Contents
Introduction to Your Projector
Setting Up the Projector
Using the Projector on a Network
Using Basic Projector Features
Adjusting Projector Features
Using the Interactive Features
Adjusting the Menu Settings
Maintaining and Transporting the Projector
- Projector Maintenance
- Transporting the Projector
Solving Problems
Technical Specifications
Notices

Epson EB-1430Wi User Manual

Displayed below is the user manual for EB-1430Wi by Epson which is a product in the Data Projectors category. This manual has pages.

Related Manuals

Epson Epson M-190: 57.5mm, 5V, Standard Ribbon Manual

Epson Epson SureColor SCF7000 Manual

Epson TM-U220A Manual

Epson TM-U295 Manual

Epson TM-U220PA Manual

Epson TM-U220PA-103 Manual

Epson TM-U295P Parallel White Manual

Epson TM-C100 Manual

BrightLink®Pro 1420Wi/1430Wi

User's Guide

Contents

BrightLink Pro 1420Wi/1430Wi User's Guide .......................................................................................... 13

Introduction to Your Projector ................................................................................................................. 14

Projector Features.............................................................................................................................. 14

Product Box Contents.................................................................................................................... 16

Additional Components ................................................................................................................ 17

Optional Equipment and Replacement Parts................................................................................. 18

Warranty and Registration Information .......................................................................................... 19

Notations Used in the Documentation ................................................................................................ 20

Where to Go for Additional Information .............................................................................................. 20

Projector Part Locations ..................................................................................................................... 21

Projector Parts - Front/Top ............................................................................................................ 21

Projector Parts - Side..................................................................................................................... 22

Projector Parts - Interface Panel.................................................................................................... 23

Projector Parts - Base.................................................................................................................... 25

Projector Parts - Control Panel ...................................................................................................... 26

Projector Parts - Interactive Pens and Pen Tray............................................................................ 27

Projector Parts - Remote Control................................................................................................... 29

Projector Parts - Touch Unit .......................................................................................................... 31

Projector Parts - Control Pad......................................................................................................... 33

Setting Up the Projector ........................................................................................................................... 35

Projector Placement........................................................................................................................... 35

Projector Setup and Installation Options ....................................................................................... 35

Projection Distance........................................................................................................................ 36

Removing and Attaching the Cable Cover.......................................................................................... 39

Adjusting the Angle of the Touch Unit ................................................................................................ 39

Installing the Projector Feet................................................................................................................ 59

Projector Connections........................................................................................................................ 60

Connecting to Computer Sources.................................................................................................. 61

Connecting to a Computer for USB Video and Audio................................................................ 61

Connecting to a Computer for VGA Video................................................................................. 62

Connecting to a Computer for HDMI Video and Audio.............................................................. 63

Connecting to a Computer for Pen Use or USB Mouse Control ................................................ 64

Connecting to a Computer for Sound........................................................................................ 65

Connecting a Computer to the Control Pad............................................................................... 65

Connecting to Video Sources ........................................................................................................ 67

Connecting to an HDMI Video Source ...................................................................................... 67

Connecting to an MHL-Compatible Device ............................................................................... 68

Connecting to a Component-to-VGA Video Source .................................................................. 68

Connecting to a Composite Video Source ................................................................................ 69

Connecting to a Video Source for Sound .................................................................................. 70

Connecting to an External Computer Monitor................................................................................ 70

Connecting to External Speakers .................................................................................................. 71

Connecting to External USB Devices ............................................................................................ 72

USB Device Projection.............................................................................................................. 72

Connecting a USB Device or Camera to the Projector.............................................................. 73

Connecting a USB Device to the Control Pad or Projector........................................................ 74

Selecting the Connected USB Source ...................................................................................... 74

Disconnecting a USB Device From the Control Pad or Projector.............................................. 74

Connecting a Printer to the Control Pad ........................................................................................ 75

Supported Printer Types ........................................................................................................... 76

Connecting to a Document Camera .............................................................................................. 76

Connecting Multiple Projectors of the Same Model ....................................................................... 77

Installing Batteries in the Remote Control .......................................................................................... 78

Installing Batteries in the Pens ........................................................................................................... 79

Installing Batteries in the Control Pad................................................................................................. 80

Using the Projector on a Network ............................................................................................................ 83

Wired Network Projection................................................................................................................... 83

Connecting to a Wired Network ..................................................................................................... 84

Selecting Wired Network Settings ................................................................................................. 84

Restricted IP Addresses ........................................................................................................... 87

Wireless Network Projection .............................................................................................................. 88

Installing the Wireless LAN Module ............................................................................................... 89

Using Quick Wireless Connection (Windows Only) ....................................................................... 91

Selecting Wireless Network Settings Manually.............................................................................. 92

Wireless LAN Menu Settings .................................................................................................... 94

Selecting Wireless Network Settings in Windows.......................................................................... 96

Selecting Wireless Network Settings in OS X ................................................................................ 97

Enabling WPA or EAP Security ..................................................................................................... 97

Wireless Security Menu Settings .............................................................................................. 98

Setting Up Projector Network E-Mail Alerts ...................................................................................... 100

Network Projector E-mail Alert Messages ................................................................................... 102

Setting Up Monitoring Using SNMP ................................................................................................. 102

Controlling a Networked Projector Using a Web Browser ................................................................ 103

Creating an Address Book ............................................................................................................... 105

Adding Templates from a Web Browser ........................................................................................... 106

Crestron RoomView Support............................................................................................................ 107

Setting Up Crestron RoomView Support ..................................................................................... 108

Controlling a Networked Projector Using Crestron RoomView .................................................... 109

Using Basic Projector Features ............................................................................................................. 111

Turning On the Projector .................................................................................................................. 111

Turning Off the Projector .................................................................................................................. 113

Selecting the Language for the Projector Menus.............................................................................. 114

Setting the Date and Time................................................................................................................ 115

Image Shape.................................................................................................................................... 117

Correcting Image Shape with the Keystone Buttons.................................................................... 117

Correcting Image Shape with Quick Corner ................................................................................ 120

Resizing the Image with the Wide and Tele Buttons ........................................................................ 121

Adjusting the Image Position............................................................................................................ 122

Focusing the Image.......................................................................................................................... 123

Remote Control Operation ............................................................................................................... 124

Using the Remote Control as a Wireless Mouse ......................................................................... 126

Using the Remote Control as a Pointer........................................................................................ 127

Selecting an Image Source .............................................................................................................. 127

Projection Modes ............................................................................................................................. 128

Changing the Projection Mode Using the Remote Control .......................................................... 129

Changing the Projection Mode Using the Menus......................................................................... 130

Image Aspect Ratio .......................................................................................................................... 130

Changing the Image Aspect Ratio ............................................................................................... 131

Available Image Aspect Ratios .................................................................................................... 131

Color Mode....................................................................................................................................... 132

Changing the Color Mode............................................................................................................ 132

Available Color Modes................................................................................................................. 133

Turning On Auto Iris..................................................................................................................... 134

Controlling the Volume with the Volume Buttons.............................................................................. 135

Projecting a PC Free Presentation ................................................................................................... 135

Supported PC Free File Types .................................................................................................... 136

Starting a PC Free Slide Show .................................................................................................... 137

Starting a PC Free Movie Presentation ....................................................................................... 139

Starting a PC Free PDF File Presentation ................................................................................... 140

Slideshow Display Options .......................................................................................................... 142

Adjusting Projector Features ................................................................................................................. 144

Shutting Off the Picture and Sound Temporarily .............................................................................. 144

Stopping Video Action Temporarily .................................................................................................. 145

Zooming Into and Out of Images ...................................................................................................... 145

Scheduling Projector Events ............................................................................................................ 146

Saving a Scheduled Event........................................................................................................... 147

Viewing Scheduled Events .......................................................................................................... 147

Editing Scheduled Events............................................................................................................ 148

Projector Security Features.............................................................................................................. 150

Password Security Types ............................................................................................................ 150

Setting a Password ................................................................................................................. 151

Selecting Password Security Types........................................................................................ 152

Entering a Password to Use the Projector............................................................................... 153

Saving a User's Logo Image to Display................................................................................... 154

Locking the Projector's Buttons ................................................................................................... 156

Unlocking the Projector's Buttons ........................................................................................... 157

Installing a Security Cable ........................................................................................................... 157

Creating a User Pattern to Display ................................................................................................... 158

Using the Interactive Features ............................................................................................................... 159

Interactive Modes............................................................................................................................. 159

Using the Interactive Pens ............................................................................................................... 160

Using the Pens ............................................................................................................................ 160

Pen Calibration............................................................................................................................ 163

Calibrating Automatically ........................................................................................................ 164

Calibrating Manually ............................................................................................................... 166

Using Finger Touch Interactivity ...................................................................................................... 169

Touch Unit Safety Instructions..................................................................................................... 169

Calibrating for Finger Touch Interactivity ..................................................................................... 171

Using Finger Touch Operations................................................................................................... 175

Using BrightLink With a Computer ................................................................................................... 177

PC Interactive Mode System Requirements................................................................................ 177

Switching to PC Interactive Mode................................................................................................ 178

Controlling Computer Features from a Projected Screen (PC Interactive Mode)......................... 179

Adjusting the Pen Operation Area ............................................................................................... 181

Easy Interactive Tools ................................................................................................................. 183

Windows Pen Input and Ink Tools ............................................................................................... 184

Enabling Windows Pen Input and Ink Tools............................................................................ 184

Using Windows Pen Input and Ink Tools................................................................................. 186

Whiteboard Mode............................................................................................................................. 187

Using the Whiteboard Toolbars ................................................................................................... 188

The Main Whiteboard Toolbar ..................................................................................................... 189

Selecting Background Templates................................................................................................ 191

Zooming Images in Whiteboard Mode......................................................................................... 192

Inserting and Working With Images............................................................................................. 192

Using the Shapes Tool ................................................................................................................ 193

Selecting Line Width and Color ................................................................................................... 194

The Bottom Whiteboard Toolbar.................................................................................................. 194

Selecting Whiteboard Settings .................................................................................................... 196

Selecting Basic Whiteboard Settings and Policies .................................................................. 196

Selecting Whiteboard Print Settings........................................................................................ 199

Selecting Settings for Saving Whiteboard Pages.................................................................... 201

Selecting Settings for Emailing Whiteboard Pages ................................................................. 203

Inserting a Document or Image From a Scanner ......................................................................... 205

Selecting a Networked Device Source ........................................................................................ 206

Saving Pages in Whiteboard Mode ............................................................................................. 208

Working With Thumbnail Pages .................................................................................................. 209

Printing in Whiteboard Mode ....................................................................................................... 210

Emailing Your Whiteboard Pages................................................................................................ 212

Sharing the Whiteboard............................................................................................................... 213

Starting a Shared Whiteboard Session ................................................................................... 214

Connecting to a Shared Whiteboard from a Computer or Other Device.................................. 216

Supported Web Browsers for Sharing a Whiteboard............................................................... 216

Web Browser Toolbars ........................................................................................................... 217

Connecting to a Shared Whiteboard from a Projector............................................................. 219

Annotation Mode (PC Free) ............................................................................................................. 220

Drawing on a Projected Image (Annotation Mode) ...................................................................... 220

Using the Annotation Toolbars .................................................................................................... 222

The Main Annotation Toolbar ...................................................................................................... 224

Zooming Images in Annotation Mode .......................................................................................... 226

The Bottom Annotation Toolbar................................................................................................... 226

Printing in Annotation Mode......................................................................................................... 227

Saving Images in Annotation Mode ............................................................................................. 228

Splitting the Screen .......................................................................................................................... 228

Adjusting the Menu Settings .................................................................................................................. 231

Using the Projector's Menus............................................................................................................. 231

Image Quality Settings - Image Menu .............................................................................................. 234

Input Signal Settings - Signal Menu.................................................................................................. 236

Projector Feature Settings - Settings Menu...................................................................................... 239

Projector Setup Settings - Extended Menu....................................................................................... 242

Projector Network Settings - Network Menu..................................................................................... 250

Projector Setup Settings - ECO Menu .............................................................................................. 252

Projector Information Display - Info Menu ........................................................................................ 254

Event ID Code List....................................................................................................................... 255

Projector Reset Options - Reset Menu ............................................................................................. 257

Maintaining and Transporting the Projector ......................................................................................... 258

Projector Maintenance ..................................................................................................................... 258

Cleaning the Projection Window.................................................................................................. 258

Cleaning the Obstacle Sensor ..................................................................................................... 259

Cleaning the Projector Case........................................................................................................ 260

Air Filter and Vent Maintenance .................................................................................................. 260

Cleaning the Air Filter and Vents............................................................................................. 260

Replacing the Air Filter............................................................................................................ 263

Projector Lamp Maintenance....................................................................................................... 266

Replacing the Lamp ................................................................................................................ 267

Resetting the Lamp Timer....................................................................................................... 271

Replacing the Remote Control Batteries ..................................................................................... 272

Replacing the Interactive Pen Batteries....................................................................................... 273

Replacing the Interactive Pen Tips .............................................................................................. 275

Transporting the Projector................................................................................................................ 276

Solving Problems .................................................................................................................................... 277

Projection Problem Tips ................................................................................................................... 277

Projector Light Status ....................................................................................................................... 278

Using the Projector Help Displays .................................................................................................... 280

Solving Image or Sound Problems ................................................................................................... 281

Solutions When No Image Appears............................................................................................. 281

Solutions When Image is Incorrect Using the USB Display Function .......................................... 282

Solutions When "No Signal" Message Appears........................................................................... 283

Displaying From a PC Laptop ................................................................................................. 283

Displaying From a Mac Laptop ............................................................................................... 284

Solutions When "Not Supported" Message Appears ................................................................... 284

Solutions When Only a Partial Image Appears............................................................................ 284

Solutions When the Image is Not Rectangular ............................................................................ 285

Solutions When the Image Contains Noise or Static ................................................................... 285

Solutions When the Image is Fuzzy or Blurry .............................................................................. 286

Solutions When the Image Brightness or Colors are Incorrect .................................................... 287

Solutions to Sound Problems ...................................................................................................... 287

Solving Projector or Remote Control Operation Problems ............................................................... 288

Solutions to Projector Power or Shut-Off Problems ..................................................................... 288

Solutions to Problems with the Remote Control........................................................................... 289

Solutions to Password Problems ................................................................................................. 290

Solutions When the Source Cannot Be Changed........................................................................ 290

Solving Interactive Problems............................................................................................................ 290

Solutions When "Error Occurred in the Easy Interactive Function" Message Appears................ 291

Solutions When the Interactive Pens Do Not Work...................................................................... 291

Solutions When the Interactive Pen Position Is Not Accurate...................................................... 292

Solutions When Manual Calibration Does Not Work.................................................................... 293

Solutions When the Interactive Pens Are Slow or Difficult to Use................................................ 293

Solutions When the Interactive Pens Cause Interference or Unwanted Effects .......................... 293

Solutions When Finger Touch Interactivity Does Not Work ......................................................... 294

Solutions for Problems With Capturing, Printing, Saving, or Scanning ........................................ 294

Solutions When Inking Does Not Appear in Microsoft Office ....................................................... 295

Solutions When the Pen Does Not Work Over a Network or the Toolbars Do Not Appear ......... 296

Solutions When the Time Is Incorrect in Whiteboard Settings ..................................................... 296

Solving Network Problems ............................................................................................................... 296

Solutions When Wireless Authentication Fails ............................................................................ 296

Solutions When You Cannot Access the Projector Through the Web ......................................... 297

Solutions When Network Alert E-Mails are Not Received............................................................ 297

Where to Get Help............................................................................................................................ 297

Technical Specifications ........................................................................................................................ 299

General Projector Specifications ...................................................................................................... 299

Projector Lamp Specifications.......................................................................................................... 300

Remote Control Specifications ......................................................................................................... 301

Interactive Pen Specifications .......................................................................................................... 301

Touch Unit Specifications ................................................................................................................ 301

Projector Dimension Specifications.................................................................................................. 302

Projector Electrical Specifications .................................................................................................... 302

Projector Environmental Specifications............................................................................................ 303

Projector Safety and Approvals Specifications................................................................................. 303

Supported Video Display Formats.................................................................................................... 303

USB Display System Requirements................................................................................................. 306

Notices ..................................................................................................................................................... 308

Recycling.......................................................................................................................................... 308

Important Safety Information ............................................................................................................ 308

Important Safety Instructions............................................................................................................ 309

Restriction of Use ........................................................................................................................ 312

FCC Compliance Statement............................................................................................................. 312

Wireless Telegraphy Act Regulations............................................................................................... 313

Trademarks...................................................................................................................................... 313

Open Source Software License........................................................................................................ 313

Copyright Notice............................................................................................................................... 365

A Note Concerning Responsible Use of Copyrighted Materials................................................... 365

Copyright Attribution.................................................................................................................... 365

BrightLink Pro 1420Wi/1430Wi User's Guide

Welcome to the BrightLink Pro 1420Wi/1430Wi User's Guide.

Introduction to Your Projector

Refer to these sections to learn more about your projector and this manual.

Projector Features

Notations Used in the Documentation

Where to Go for Additional Information

Projector Part Locations

Projector Features

The BrightLink Pro 1420Wi/1430Wi projectors include these special features:

Unique interactive functions

• Annotation with or without a computer

• Annotation with two pens at the same time

• Enhanced Easy Interactive toolbar for Windows and Mac

• Touch-based interactivity for as many as six users (BrightLink Pro 1430Wi)

• Share your whiteboard with up to 15 other devices, including tablets, smartphones, and other

projectors with whiteboard sharing capabilities

• Annotate projected content from your device

• Scan and display content from a connected scanner

• Email, save, or print your content without a computer

• Import content from a USB drive

Ultra short throw projection system

• Project an 87-inch (221-cm) image (WXGA) from just 9.1 inches (231 mm) away

• Easily mounted on a wall (with the wall mount) or table (with the optional table projection mount) for

fast, low-cost installations

• Can be mounted vertically to create an interactive workspace directly on a table surface

• Reduced shadow interference and glare

Bright, high-resolution images

• Up to 3300 lumens of color brightness (color light output) and 3300 lumens of white brightness (white

light output)

Note: Color brightness (color light output) and white brightness (white light output) will vary depending

on usage conditions. Color light output measured in accordance with IDMS 15.4; white light output

measured in accordance with ISO 21118.

• Native resolution of 1280 × 800 pixels (WXGA)

Flexible connectivity

• HDMI 1/MHL and HDMI 2 ports for computer or video device connection

• Plug-and-play 3-in-1 USB projection, audio, and mouse control for instant setup

• Wired network support for projection

• Projector monitoring and control via remote network computer

• Optional wireless network support, including video and audio transfer

• PC Free photo slide shows via connected USB memory devices or Epson document camera

• Dual VGA ports for connections by multiple presenters

• Port for connecting an external monitor

• Projection from iOS or Android devices with the wireless LAN module and free Epson iProjection app;

visit epson.com/projectorapp (U.S.) or epson.ca/projectorapp (Canada) for more information

Innovative display and operation features

• Low total cost of ownership with long-life projector lamp and high-efficiency air filter

• High digital zoom ratio for larger images in shorter projection distances

• 10000:1 contrast ratio and Auto Iris control for sharp, detailed images

• Built-in closed captioning decoder

• Powerful 16 W speaker system with audio out port for connecting external speakers

• Epson's Instant Off and Direct Power On features for quick setup and shut down

• Support for Crestron RoomView network monitoring systems

• Network message broadcast system to project timely messages to all networked projectors

Product Box Contents

Additional Components

Optional Equipment and Replacement Parts

Warranty and Registration Information

Parent topic: Introduction to Your Projector

Product Box Contents

Save all the packaging in case you need to ship the projector. Always use the original packaging (or

equivalent) when shipping.

Make sure your projector box included all of these parts:

1 Projector

2 Remote control

3 Remote control batteries (two AA alkaline)

4 Pens and batteries (one AA alkaline battery for each pen)

5 Rubber feet (BrightLink Pro 1420Wi)

6 Pen tray

7 USB cables (3)

8 Power cord

9 Touch Unit connection cable (BrightLink Pro 1430Wi)

10 Password Protected sticker

11 Projector manuals and software links CD

12 Projector software for Easy Interactive Function CD

13 Touch Unit and markers (inside the unit) (BrightLink Pro 1430Wi)

14 Labels (4) (BrightLink Pro 1430Wi)

15 Tape for securing markers (BrightLink Pro 1430Wi)

16 Infrared deflectors (8) (BrightLink Pro 1430Wi)

17 Wireless LAN unit

18 Control Pad (with batteries)

Parent topic: Projector Features

Additional Components

Depending on how you plan to use the projector, you may need to obtain the following additional

components:

• To receive a composite video signal, you need an RCA-style video or A/V cable. See your local

computer or electronics dealer for purchase information.

• To receive a component video signal, you need a D-sub, 15-pin, component-to-VGA video cable. You

can purchase one from Epson or an authorized Epson reseller.

• To receive an HDMI signal, you need a compatible HDMI cable. You can purchase one from Epson or

an authorized Epson reseller.

Note: To connect a Mac that includes only a Mini DisplayPort, Thunderbolt port, or Mini-DVI port for

video output, you need to obtain an adapter that allows you to connect to the projector's HDMI port.

Contact Apple for compatible adapter options. Older Mac computers (2009 and earlier) may not

support audio through the HDMI port.

• To receive an HDMI signal via MHL, you need an MHL-compatible device, an MHL cable or an HDMI

cable and an MHL adapter compatible with your device. Devices with an integrated MHL connector

may not require a cable.

• To sync additional BrightLink Pro projectors together, you will need a stereo mini cable or the remote

control cable set (ELPKC28).

• To power the Control Pad from the projector, you will need the remote control cable set (ELPKC28).

• To project with audio from certain ports, you may need a commercially available audio cable

compatible with your device. See your local computer or electronics dealer for purchase information.

• If you did not purchase a mount that included a VGA cable, you may need a VGA computer cable. You

can purchase one from Epson or an authorized Epson reseller.

Parent topic: Projector Features

Optional Equipment and Replacement Parts

You can purchase screens, other optional accessories, and replacement parts from an Epson authorized

reseller. To find the nearest reseller, call 800-GO-EPSON (800-463-7766). Or you can purchase online

at epsonstore.com (U.S. sales) or epson.ca (Canadian sales).

Epson offers the following optional accessories and replacement parts for your projector:

Option or part Part number

Genuine Epson replacement lamp (ELPLP80) V13H010L80

Replacement air filter (ELPAF40) V13H134A40

Quick wireless connection USB key (ELPAP09) V12H005M09

SMART Notebook software V12HSSW020

Mimio MimioStudio Software for BrightLink Projectors V12HMSS020

Wall mount (ELPMB43) V12H675020

Table projection mount (ELPMB29) V12H516020

Epson DC-06 document camera (ELPDC06) V12H321005

Epson DC-11 document camera (ELPDC11) V12H377020

Epson DC-12 document camera (ELPDC12) V12H594020

Option or part Part number

Epson DC-20 document camera (ELPDC20) V12H500020

PowerLite Pilot 2 (ELPCB02) V12H614020

Active speakers (ELPSP02) V12H467020

Additional interactive pen A (ELPN04A) (orange) V12H666010

Additional interactive pen B (ELPN04B) (blue) V12H667010

Replacement set of 6 pen tips (ELPPS02) V12H668010

Interactive Pen Extension (ELPPE01) V12H590001

USB extension cable V12H525001

Remote control cable set (ELPKC28) V12H005C28

On Wall Cable Management Kit ELPCK01

Kensington security lock ELPSL01

Touch Unit attachment mount (BrightLink Pro 1430Wi) ELPPT05

90-inch whiteboard V12H468002

96-inch whiteboard V12H468001

6 ft. (1.8 m) VGA computer cable F3H982-06

10 ft. (3.0 m) VGA computer cable F3H982-10

10 ft. (3.0 m) Component-to-VGA video cable ELPKC19

In addition to the accessories listed above, 1-year and 2-year extended service plans are available.

Parent topic: Projector Features

Warranty and Registration Information

Your projector comes with a basic warranty that lets you project with confidence. For details, see the

warranty that came with your projector.

In addition, Epson offers free Extra Care Road Service. In the unlikely event of an equipment failure, you

won’t have to wait for your unit to be repaired. Instead, Epson will ship you a replacement unit anywhere

in the United States, Canada, or Puerto Rico. See the Extra Care Road Service brochure for details.

Registering also lets you receive special updates on new accessories, products, and services.

Parent topic: Projector Features

Notations Used in the Documentation

Follow the guidelines in these notations as you read your documentation:

•Warnings must be followed carefully to avoid bodily injury.

•Cautions must be observed to avoid damage to your equipment.

•Notes contain important information about your projector.

•Tips contain additional projection information.

Parent topic: Introduction to Your Projector

Where to Go for Additional Information

Need quick help on using your projector? Here's where to look for help:

• Built-in help system

Press the Help button on the remote control or projector to get quick solutions to common problems.

• Help icon on the bottom whiteboard toolbar

Select the help icon to get a quick summary of the tools and features available.

•epson.com/support (U.S) or epson.ca/support (Canada)

View FAQs (frequently asked questions) and e-mail your questions to Epson technical support 24

hours a day.

• For detailed instructions on using your projector in a network environment, see the EasyMP Network

Projection Operation Guide.

• For detailed instructions on monitoring your projector in a network environment (Windows only), see

the EasyMP Monitor Operation Guide.

• For detailed instructions on using your projector to hold interactive meetings in a network environment,

see the EasyMP Multi PC Projection Operation Guide.

• If you still need help after checking this manual and the sources listed above, you can use the Epson

PrivateLine Support service to get help fast. For details, see "Where to Get Help".

Parent topic: Introduction to Your Projector

Projector Part Locations

Check the projector part illustrations to learn about the parts on your projector.

Projector Parts - Front/Top

Projector Parts - Side

Projector Parts - Interface Panel

Projector Parts - Base

Projector Parts - Control Panel

Projector Parts - Interactive Pens and Pen Tray

Projector Parts - Remote Control

Projector Parts - Touch Unit

Projector Parts - Control Pad

Parent topic: Introduction to Your Projector

Projector Parts - Front/Top

1 Remote control receiver

2 Speaker

3 Control panel

4 Cable cover screws

5 Cable cover

6 Exhaust vent

7 Lamp cover screw

8 Lamp cover

Parent topic: Projector Part Locations

Projector Parts - Side

1 Filter cover switch

2 Security cable installation slot

3 Wireless LAN light

4 Interactive pen receiver

5 Obstacle sensor

6 Remote receiver

7 Projection window

8 Security lock port

9 Air filter cover

10 Air intake vent (air filter)

11 Focus lever

Parent topic: Projector Part Locations

Projector Parts - Interface Panel

1 Wireless LAN module port

2Audio port

3Computer port

4Audio Out port

5USB-B port

6Monitor Out port

7 Network (LAN) port

8HDMI 2 port

9HDMI 1/MHL port

10 Audio port

11 RS-232C port

12 SYNC In/Out ports

13 Power inlet

14 TCH port for the Touch Unit connection cable (BrightLink Pro 1430Wi)

15 USB-A port

16 USB-A port (for document camera)

17 Video port

18 Audio port

19 Remote port (for optional connection to the Control Pad)

Parent topic: Projector Part Locations

Related references

Projector Light Status

Projector Parts - Base

1 Ceiling mount holes (5)

2 Security cable attachment point

3 Rear foot attachment points (2) (BrightLink Pro 1420Wi)

4 Wall mount plate holes (4)

5 Illumination sensor

6 Front foot attachment point (BrightLink Pro 1420Wi)

Parent topic: Projector Part Locations

Related tasks

Installing the Projector Feet

Projector Parts - Control Panel

1 Projector status lights

2Source Search button (searches for connected video sources)

3Enter button (selects options)

4 Horizontal/Vertical keystone adjustment buttons (display the adjustment screen and adjust screen

shape) and arrow buttons

5 Help button (accesses projector help information)

6Esc button (cancels/exits functions)

7Wide/Tele buttons (adjust projected image size), horizontal keystone adjustment buttons (adjust

screen shape), and arrow buttons

8Menu button (accesses projector menu system)

9 Power button

Parent topic: Projector Part Locations

Projector Parts - Interactive Pens and Pen Tray

1 Pen tip

2 Battery light

3 Power/function button

4 Attachment for optional strap or cord

5 Battery cover

1 Installation magnets

2 Mounting holes

3 Security lock hole

Parent topic: Projector Part Locations

Projector Parts - Remote Control

1 Power button

2Capture button (captures the annotation screen and pastes it as a new whiteboard page)

3Print button (prints the projected screen)

4 Numeric buttons (enter numbers)

5Auto button (automatically adjusts position, tracking, and sync settings)

6Aspect button (selects the image aspect ratio)

7Num button (when held down, switches numeric buttons to number function)

8Menu button (accesses projector menu system)

9 Arrow buttons (move through on-screen options and control wireless mouse functions)

10 Enter button (selects options and controls wireless mouse functions)

11 User button (customizable for different functions)

12 Page up/down buttons (control presentation slides)

13 E-Zoom +/–buttons (zoom into and out of the image)

14 A/V Mute button (turns off picture and sound)

15 Split button (toggles split screen mode)

16 Strap attachment point

17 Help button (accesses projector help information)

18 Freeze button (stops video action)

19 Volume up/down buttons (adjust speaker volume)

20 Pointer button (activates on-screen pointer)

21 Esc button (cancels/exits functions and controls wireless mouse functions)

21 Pen Mode button (cycles between PC Interactive and PC Free Annotation modes)

23 Color Mode button (selects display modes)

24 MHL Menu button (displays settings or performs functions for the MHL device)

25 Whiteboard button (turns the projector on (if necessary) and displays Whiteboard mode)

26 Save button (saves the displayed image to a USB drive or network folder)

27 Source Search button (searches for connected sources)

Parent topic: Projector Part Locations

Projector Parts - Touch Unit

The Touch Unit comes with the BrightLink Pro 1430Wi projector only.

Front (Cover On)

Front (Cover Off)

1 Dial cover

2 TCH port

3 Security slot

4 Adjustment dials

5 Power light

Rear

1 Laser diffusion ports

2 Installation magnets

3 Guide markers (used for performing angle adjustment)

Parent topic: Projector Part Locations

Projector Parts - Control Pad

1 Power button

2Whiteboard button (switches to whiteboard mode)

3Source Search button (searches for connected sources)

4Capture button (captures projected image in annotation mode)

5Print button (prints the projected image)

6Save button (saves the projected image)

7 USB-B port for connecting a computer (on bottom of control pad)

8USB-A port for connecting a USB thumbdrive or other storage device (under bottom cover)

9Printer USB-A port for connecting a printer (under top cover)

10 USB-B port for connecting to the projector for printing or thumbdrive access (under top cover)

11 USB-A port for connecting to the projector for interactive functions (under top cover)

12 Remote port for connecting the optional remote control cable (under top cover)

13 Light emitting areas (output remote control signals)

14 Bottom cover (open to connect a USB thumbdrive or other storage device)

15 Top cover (open to connect cables or replace batteries)

16 Cable cover (open when cables are wired along a wall)

Parent topic: Projector Part Locations

Setting Up the Projector

Follow the instructions in these sections to set up your projector for use.

Projector Placement

Removing and Attaching the Cable Cover

Adjusting the Angle of the Touch Unit

Installing the Projector Feet

Projector Connections

Installing Batteries in the Remote Control

Installing Batteries in the Pens

Installing Batteries in the Control Pad

Projector Placement

Your ultra-short throw projector is designed to be installed on a wall (with a wall mount) or vertically on a

table (with a table mount) to create an interactive tabletop workspace.

Keep these considerations in mind as you select a projector location:

• Follow the instructions in the Installation Guide provided with your mounting hardware to install the

projector using the included mounting equipment.

• Leave plenty of space around and under the projector for ventilation, and do not place it on top of or

next to anything that could block the vents.

• Position the projector within reach of a grounded electrical outlet or extension cord.

• If installing vertically on a desk or table, the table projection mount (V12H516020) is required.

• If installing on a wall, the wall mount (V12H675020) is required.

Projector Setup and Installation Options

Projection Distance

Parent topic: Setting Up the Projector

Projector Setup and Installation Options

You can set up or install your projector in the following ways:

Mounted on the wall or ceiling

Mounted vertically on a table to create an interactive workspace

Wherever you set up the projector, make sure to position it squarely in front of the screen, not at an

angle.

Parent topic: Projector Placement

Related references

Projector Setup Settings - Extended Menu

Projection Distance

The distance at which you place the projector from the screen determines the approximate size of the

image. The image size increases the farther the projector is from the screen, but can vary depending on

the zoom factor, aspect ratio, and other settings.

Use the tables here to determine approximately how far to place the projector from the screen based on

the size of the projected image. (Conversion figures may have been rounded up or down.) For more

detailed information and installation instructions, see the Installation Guide provided with your wall

mount. You can also use the projector Throw Distance Calculator at epson.com/support (U.S.) or

epson.ca/support (Canada).

Note: All minimum ceiling heights are based on an image 30 inches (76 cm) from the floor.

16:10 Aspect Ratio

Diagonal

image

size

Min. ceiling

height

Image

width

Image height Min. projection

distance

Distance from top

of image to wall

plate holes

60 inches 78.7 inches

(199.8 cm)

50.9

inches

(129.2 cm)

31.8 inches

(80.8 cm)

2.5 inches

(6.2 cm)

6.9 inches (17.4 cm)

70 inches 85.0 inches

(215.9 cm)

59.4

inches

(150.8 cm)

37.1 inches

(94.2 cm)

4.9 inches

(12.4 cm)

7.9 inches (20.1 cm)

80 inches 91.4 inches

(232.0 cm)

67.8

inches

(172.3 cm)

42.4 inches

(107.7 cm)

7.3 inches

(18.7 cm)

9.0 inches (22.7 cm)

88 inches 96.4 inches

(245.0 cm)

74.6

inches

(189.5 cm)

46.6 inches

(118.5 cm)

9.3 inches

(23.6 cm)

9.8 inches (24.9 cm)

90 inches 97.7 inches

(248.2 cm)

76.3

inches

(193.9 cm)

47.7 inches

(121.2 cm)

9.8 inches

(24.9 cm)

10.0 inches

(25.4 cm)

100 inches 104.1 inches

(264.3 cm)

84.8

inches

(215.4 cm)

53.0 inches

(134.6 cm)

12.2 inches

(31.1 cm)

11.1 inches

(28.1 cm)

16:9 Aspect Ratio

Diagonal

image

size

Min. ceiling

height

Image width Image height Min. projection

distance

Distance from top

of image to wall

plate holes

59 inches 77.5 inches

(196.8 cm)

51.5 inches

(130.6 cm)

28.9 inches

(73.5 cm)

2.6 inches

(6.6 cm)

8.5 inches (21.7 cm)

Diagonal

image

size

Min. ceiling

height

Image width Image height Min. projection

distance

Distance from top

of image to wall

plate holes

60 inches 78.1 inches

(198.3 cm)

52.3 inches

(132.8 cm)

29.4 inches

(74.7 cm)

2.9 inches

(7.3 cm)

8.7 inches (22.0 cm)

70 inches 84.3 inches

(214.2 cm)

61.0 inches

(155.0 cm)

34.3 inches

(87.2 cm)

5.4 inches

(13.7 cm)

10.0 inches

(25.4 cm)

77 inches 88.7 inches

(225.3 cm)

67.1 inches

(170.5 cm)

37.8 inches

(95.9 cm)

7.1 inches

(18.1 cm)

11.0 inches

(27.8 cm)

80 inches 90.6 inches

(230.1 cm)

69.7 inches

(177.1 cm)

39.2 inches

(99.6 cm)

7.9 inches

(20.0 cm)

11.4 inches

(28.9 cm)

90 inches 96.8 inches

(246.0 cm)

78.4 inches

(199.2 cm)

44.1 inches

(112.1 cm)

10.4 inches

(26.4 cm)

12.7 inches

(32.3 cm)

97 inches 101.2 inches

(257.1 cm)

84.5 inches

(214.7 cm)

47.6 inches

(120.8 cm)

12.2 inches

(30.9 cm)

13.7 inches

(34.7 cm)

4:3 Aspect Ratio

Diagonal

image

size

Min. ceiling

height

Image width Image height Min. projection

distance

Distance from top

of image to wall

plate holes

53 inches 78.7 inches

(199.8 cm)

42.4 inches

(107.7 cm)

31.8 inches

(80.8 cm)

2.5 inches

(6.2 cm)

6.9 inches (17.4 cm)

60 inches 83.7 inches

(212.5 cm)

48 inches

(121.9 cm)

36 inches

(91.4 cm)

4.4 inches

(11.2 cm)

7.7 inches (19.5 cm)

70 inches 90.9 inches

(230.8 cm)

56.0 inches

(142.2 cm)

42 inches

(106.7 cm)

7.2 inches

(18.2 cm)

8.9 inches (22.5 cm)

77 inches 95.9 inches

(243.6 cm)

61.6 inches

(156.5 cm)

46.2 inches

(117.3 cm)

9.1 inches

(23.1 cm)

9.7 inches (24.7 cm)

80 inches 98.1 inches

(249.1 cm)

64 inches

(162.6 cm)

48 inches

(121.9 cm)

9.9 inches

(25.2 cm)

10.1 inches

(25.6 cm)

88 inches 103.8 inches

(263.7 cm)

70.4 inches

(182.9 cm)

52.8 inches

(134.1 cm)

12.1 inches

(30.8 cm)

11.0 inches

(28.0 cm)

Parent topic: Projector Placement

Removing and Attaching the Cable Cover

Before you can connect equipment to your projector, you need to remove the cable cover.

1. Remove both of the cable cover screws (screwdriver not included).

2. Slide off the cable cover.

To attach the cable cover, slide it into position and tighten the screws.

Parent topic: Setting Up the Projector

Adjusting the Angle of the Touch Unit

You can adjust the angle of the Touch Unit to detect the position of your fingers.

Note: These instructions require that the Touch Unit is mounted and connected according to the

Installation Guide provided with your projector or projector mount.

1. Turn the projector on.

2. Loosen the screw at the bottom of the Touch Unit.

3. Remove the dial cover from the Touch Unit.

4. Remove the markers from inside the Touch Unit.

5. Press the Menu button on the remote control or projector control panel.

6. Select Easy Interactive Function from the Extended menu.

7. Select Touch Unit Setup.

8. Make sure Power is set to On.

The Touch Unit power turns on and the indicator light turns blue.

Warning: Do not look into the projector's projection window or the Touch Unit's laser diffusion ports

(located on the back of the Touch Unit); this could cause injury to eyesight.

9. Select Angle Adjustment.

The Angle Adjustment screen is displayed.

10. Turn the adjustment dials on the Touch Unit counterclockwise until you hear a click. Press the

button on the remote control.

Note: Make sure to stop turning the dials when you hear the click.

11. Attach the two markers you removed from the Touch Unit to the marker positions shown on the

projected screen ( ) ( ).

12. Match the positions so that the crosses (A) overlap with the points (B) on the marker positions ( ) (

). Move the marker over the projected cross until the lines of the cross align with the lines on the

marker.

13. When pointers ( ) ( ) with the same color (blue and green) as the marker positions are

displayed on the left and right of the projection surface, attach the markers to the projection surface

as follows:

• For magnetic screens: Place the bottom of the markers on the screen.

• For non-magnetic screens: Use the supplied tape to secure the markets. Attach the tape so that

each end of the marker is secure on the screen.

Correct position:

Incorrect position:

Note: Do not place anything other than the markers near the projected image during angle

adjustment. If other objects are on the projected image, angle adjustment may not be performed

correctly.

14. Turn the adjustment dials on the Touch Unit to move the pointers so that they move inside of the

target of the same color (blue and green) on either side.

Turning an adjustment dial clockwise moves the pointer diagonally up towards the center of the

projected image.

Turning an adjustment dial counterclockwise moves the pointer diagonally down away from the

center of the projected image.

When the pointers are inside the target, the colors become solid ( ) ( )

Note: If a dial makes a clicking sounds, the pointer will not move any further. When turning the dials,

make sure the shadows from your arm or body do not cover the markers.

15. When the pointers on the left and right become solid colors, press the button on the remote

control.

The next adjustment screen is displayed.

16. Place the markers at the top marker positions [1]. When angle adjustment is performed correctly, the

upper pointers become solid colors. If the upper pointers do not become solid colors, start again

from step 9.

17. Place the markers at the bottom marker positions [2]. When angle adjustment is performed correctly,

the bottom pointers become solid colors. If the bottom pointers do not become solid colors, start

again from step 9.

18. When you have finished checking the marker positions, remove the markets and press the button

on the remote control.

The following confirmation screen is displayed:

19. Trace the dots with your finger as shown. When angle adjustment is performed correctly, the traced

dots disappear.

Note: Finger touch operations may not function correctly if you are wearing bandages, artificial nails,

nail polish, or anything else that may obstruct your fingers.

20. When all of the dots have disappeared, press the press the button on the remote control and go

to the next step.

If any dots remain (as shown below), do the following:

• Remove any obstacles from around the projected screen. When you are finished, press the up or

down arrow button on the remote control and repeat step 19.

• If the dots still remain after removing obstacles, turn the adjustment dials about a quarter turn

counterclockwise. Press the up or down arrow button on the remote control and repeat step 19.

• If the dots still remain or there are obstacles that cannot be removed, such as whiteboard trays or

frames, go to step 21.

21. If there is an obstacle that cannot be removed such as a whiteboard tray or frame, remove the tape

from the back of the supplied infrared deflectors and stick them to the screen so that the laser is not

reflected by the obstacle.

Make sure to stick the deflectors between the dots and the obstacle and adjust the number of

deflectors according to the number of dots.

Note: Do not remove an infrared deflector once is has been stuck in place. Do not stick tape or place

anything on the infrared deflectors. The deflectors will not function properly if anything is placed on

them.

22. After placing the infrared deflectors, press the up or down arrow button on the remote control and

repeat step 19.

If the dots do not disappear even after attaching the infrared deflectors, turn the adjustment dials

about a quarter turn counterclockwise. Press the up or down arrow button on the remote control and

repeat step 19.

Note: If the dots do not disappear even after performing the above procedure, contact Epson

support.

23. Perform touch calibration by pressing the Menu button on the remote control. On the Extended

menu, select Easy Interactive Function, then select Touch Unit Setup. Select Touch Calibration

and follow the instructions.

24. After you have finished touch calibration, store the markers inside the Touch Unit.

25. Attach the supplied labels to the tabs on either side of the Touch Unit. Match the center of the labels

with the tabs on the Touch Unit.

If the Touch Unit moves out of position, use the position of the labels to determine where to

reposition the Touch Unit.

26. Attach the dial cover. Make sure to tighten the screw at the bottom of the cover.

Parent topic: Setting Up the Projector

Related references

Touch Unit Safety Instructions

Related tasks

Calibrating for Finger Touch Interactivity

Using Finger Touch Operations

Installing the Projector Feet

To use the projector on a table or cart, you first need to install the feet (BrightLink Pro 1420Wi). You can

then use the feet to adjust the image position.

1. Turn the projector upside down.

2. Insert the larger front foot into the hole at the front of the projector.

1 Front foot (larger)

2 Rear feet

3. Insert the two smaller rear feet into the holes at the back of the projector.

Parent topic: Setting Up the Projector

Projector Connections

You can connect the projector to a variety of computer, video, and audio sources to display

presentations, movies, or other images, with or without sound.

• Connect any type of computer that has a USB port, standard video output (monitor) port, or HDMI port.

• For video projection, connect devices such as DVD players, gaming consoles, digital cameras, and

smartphones with compatible video output ports.

• If your presentation or video includes sound, you can connect audio input cables, if necessary.

• For slide shows without a computer, you can connect USB devices (such as a flash drive or camera)

or an optional Epson document camera.

Caution: If you will use the projector at altitudes above 4921 feet (1500 m), turn on High Altitude Mode

to ensure the projector's internal temperature is regulated properly.

Connecting to Computer Sources

Connecting to Video Sources

Connecting to an External Computer Monitor

Connecting to External Speakers

Connecting to External USB Devices

Connecting a Printer to the Control Pad

Connecting to a Document Camera

Connecting Multiple Projectors of the Same Model

Parent topic: Setting Up the Projector

Related references

Projector Setup Settings - Extended Menu

Connecting to Computer Sources

Follow the instructions in these sections to connect a computer to the projector.

Connecting to a Computer for USB Video and Audio

Connecting to a Computer for VGA Video

Connecting to a Computer for HDMI Video and Audio

Connecting to a Computer for Pen Use or USB Mouse Control

Connecting to a Computer for Sound

Connecting a Computer to the Control Pad

Parent topic: Projector Connections

Connecting to a Computer for USB Video and Audio

If your computer meets the system requirements, you can send video and audio output to the projector

through the computer's USB port (preferably USB 2.0). Connect the projector to your computer using a

USB cable.

You can also connect your computer to the control pad.

Note: This also lets you use the interactive pens with your computer. You need to change the USB Type

Bsetting in the projector's Extended menu before you can project through the USB port. Note that using

USB Display will slow interactive pen function. For the best performance, VGA or HDMI connections are

recommended.

Note: You can connect your computer's USB cable to the control pad instead of directly to the projector.

1. Turn on your computer.

2. Connect the cable to your projector's USB-B port.

3. Connect the other end to any available USB port on your computer.

4. To use USB Display, do one of the following:

•Windows 8.x: Click EPSON_PJ_UD in the upper right-corner, then select Run EMP_UDSE.exe

in the dialog box that appears to install the Epson USB Display software.

•Windows 7/Windows Vista: Select Run EMP_UDSE.exe in the dialog box that appears to install

the Epson USB Display software.

•Windows XP: Wait as messages appear on your computer screen and the projector installs the

Epson USB Display software on your computer.

•Windows 2000: Select Computer,EPSON_PJ_UD, and EMP_UDSE.EXE to install the Eposn

USB Display software.

•OS X: The USB Display setup folder appears on your screen. Select USB Display Installer and

follow the on-screen instructions to install the Epson USB Display software.

Follow any on-screen instructions. You need to install this software only the first time you connect

the projector to the computer.

The projector displays the image from your computer's desktop and outputs sound, if your presentation

contains audio.

Parent topic: Connecting to Computer Sources

Connecting to a Computer for VGA Video

You can connect the projector to your computer using a VGA computer cable.

Note: To connect a Mac that includes only a Mini DisplayPort, Thunderbolt port, or Mini-DVI port for

video output, you need to obtain an adapter that allows you to connect to the projector's VGA video port.

Contact Apple for compatible adapter options.

1. If necessary, disconnect your computer's monitor cable.

2. Connect the VGA computer cable to your computer's monitor port.

3. Connect the other end to a Computer port on the projector.

4. Tighten the screws on the VGA connector.

Parent topic: Connecting to Computer Sources

Connecting to a Computer for HDMI Video and Audio

If your computer has an HDMI port, you can connect it to the projector using an optional HDMI cable.

Note: To connect a Mac that includes only a Mini DisplayPort, Thunderbolt port, or Mini-DVI port for

video output, you need to obtain an adapter that allows you to connect to the projector's HDMI port.

Contact Apple for compatible adapter options. Older Mac computers (2009 and earlier) may not support

audio through the HDMI port.

1. Connect the HDMI cable to your computer's HDMI output port.

2. Connect the other end to one of the projector's HDMI ports.

Note: The projector converts the digital audio signal sent from your computer into a mono analog signal

for the internal speaker or a stereo analog signal if you are connecting to external speakers.

Parent topic: Connecting to Computer Sources

Connecting to a Computer for Pen Use or USB Mouse Control

If you connected your computer to a Computer or HDMI port on the projector, you also need to connect

the USB cable so you can use the pens with your computer.

Note: You can connect your computer's USB cable to the control pad instead of directly to the projector.

Connecting the USB cable also lets you set up the remote control to act as a wireless mouse, but you

cannot use this feature at the same time you are using the pens with your computer.

1. Connect the USB cable to your projector's USB-B port.

2. Connect the other end to any available USB port on your computer.

If you want to use the remote control as a wireless mouse, you need to change the USB Type B setting

in the projector's Extended menu. You may also need to configure your computer to work with an

external USB mouse. See your computer documentation for details.

Parent topic: Connecting to Computer Sources

Related references

Projector Setup Settings - Extended Menu

Projector Parts - Remote Control

Related tasks

Using the Remote Control as a Wireless Mouse

Connecting to a Computer for Sound

If your computer presentation includes sound and you did not connect it to the projector's USB-B or an

HDMI port, you can still play sound through the projector's speaker system. Just connect an optional

3.5 mm stereo mini-jack audio cable as described here.

1. Connect the audio cable to your laptop's headphone or audio-out jack, or your desktop's speaker or

audio-out port.

2. Connect the other end to the Audio port that corresponds to the Computer port you are using.

Parent topic: Connecting to Computer Sources

Connecting a Computer to the Control Pad

If your computer meets the system requirements, you can send video and audio output to the projector

through the control pad's USB-B port (preferably USB 2.0). Connect the projector and your computer to

the control pad using USB cables.

Caution: Make sure the control pad is positioned no more than 6.5 ft (2 m) away from the projector, and

no obstacles are blocking the signal from the projector. Do not place the control pad behind the

projection surface.

Note: This also lets you use the interactive pens with your computer. You need to adjust the USB Type

Bsetting in the projector's Extended menu before you can project through the USB port. Note that using

USB Display will slow interactive pen function. For the best performance, VGA or HDMI connections are

recommended, in addition to the USB connection for interactive pen usage.

1. Turn on your computer.

2. Make sure a USB cable is connected between the USB-B port on the projector and the USB-A port

on the control pad.

3. Connect another USB cable to the USB port on the bottom of the control pad and any available USB

port on your computer.

4. To use USB Display, do one of the following:

•Windows 8.x: Click EPSON_PJ_UD in the upper right-corner, then select Run EMP_UDSe.exe

in the dialog box that appears to install the Epson USB Display software.

•Windows 7/Windows Vista: Select Run EMP_UDSE.exe in the dialog box that appears to install

the Epson USB Display software.

•Windows XP: Wait as messages appear on your computer screen and the projector installs the

Epson USB Display software on your computer.

•Windows 2000: Select Computer,EPSON_PJ_UD, and EMP_UDSE.EXE to install the Epson

USB Display software.

•OS X: The USB Display setup folder appears on your screen. Select USB Display Installer and

follow the on-screen instructions to install the Epson USB Display software.

Follow any on-screen instructions. You need to install this software only the first time you connect

the projector to the computer.

The projector displays the image from your computer's desktop and outputs sound, if your presentation

contains audio.

Parent topic: Connecting to Computer Sources

Connecting to Video Sources

Follow the instructions in these sections to connect video devices to the projector.

Connecting to an HDMI Video Source

Connecting to an MHL-Compatible Device

Connecting to a Component-to-VGA Video Source

Connecting to a Composite Video Source

Connecting to a Video Source for Sound

Parent topic: Projector Connections

Connecting to an HDMI Video Source

If your video source has an HDMI port, you can connect it to the projector using an optional HDMI cable.

The HDMI connection provides the best image quality.

1. Connect the HDMI cable to your video source's HDMI output port.

2. Connect the other end to one of the projector's HDMI ports.

Note: The projector converts the digital audio signal sent from your video source into a mono analog

signal for the internal speaker or a stereo analog signal if you are connecting to external speakers.

Parent topic: Connecting to Video Sources

Connecting to an MHL-Compatible Device

If you have an MHL-compatible smartphone or tablet, you can connect it to the projector using either an

MHL cable or an HDMI cable with a device-compatible MHL adapter. If you have a device with a built-in

MHL connector, plug it directly into the HDMI 1/MHL port.

Note: Some connected devices may not charge when using an MHL adapter.

1. Connect the MHL cable or adapter to your device's Micro-USB port.

2. If you are using an MHL adapter, connect it to an MHL-compatible HDMI cable.

3. Connect the other end of the cable to the projector's HDMI 1/MHL port.

Note: The projector converts the digital audio signal sent from your video source into a mono analog

signal for the internal speaker or a stereo analog signal if you are connecting to external speakers.

Parent topic: Connecting to Video Sources

Connecting to a Component-to-VGA Video Source

If your video source has component video ports, you can connect it to the projector using an optional

component-to-VGA video cable. Depending on your component ports, you may need to use an adapter

cable along with a component video cable.

1. Connect the component connectors to your video source's color-coded component video output

ports, usually labeled Y,Pb,Pr or Y,Cb,Cr. If you are using an adapter, connect these connectors

to your component video cable.

2. Connect the VGA connector to a Computer port on the projector.

3. Tighten the screws on the VGA connector.

If your image colors appear incorrect, you may need to change the Input Signal setting in the projector's

Signal menu.

Parent topic: Connecting to Video Sources

Connecting to a Composite Video Source

If your video source has a composite video port, you can connect it to the projector using an optional

RCA-style video or A/V cable.

1. Connect the cable with the yellow connector to your video source's yellow video output port.

2. Connect the other end to the projector's Video port.

Parent topic: Connecting to Video Sources

Connecting to a Video Source for Sound

You can play sound through the projector's speaker system if your video source has audio output ports.

Connect the projector to the video source using a stereo mini-jack adapter cable (with one 3.5 mm mini-

plug and two RCA plugs).

Note: If you connected your video source to the projector using an HDMI or MHL cable, the audio signal

is transferred with the video signal; you do not need an additional cable for sound.

1. Connect the audio cable to your video source's audio-out ports.

2. Connect the other end of the cable to the projector's Audio port or ports.

Note: To add additional sound, connect your video source and speakers to an audio video receiver,

then connect the receiver to the projector using one of the receiver's compatible video outputs (an

HDMI connection provides the best image quality, if available). You can also connect speakers to

any video source that has its own speaker connections. External powered speakers or headphones

can also be connected to the Audio Out port using a 3.5 mm stereo mini jack cable.

Parent topic: Connecting to Video Sources

Connecting to an External Computer Monitor

If you connected the projector to a computer using a Computer port, you can also connect an external

monitor to the projector. This lets you see your presentation on the external monitor even when the

projected image is not visible.

If you want to output images to an external monitor when the projector is turned off, you need to select

Communication On as the Standby Mode setting and Always On as the A/V Output setting in the

projector's menu system.

Note: Monitors that use a refresh rate less than 60 Hz may not be able to display images correctly.

1. Make sure your computer is connected to the projector's Computer port.

2. Connect the external monitor's cable to your projector's Monitor Out port.

Note: Only analog RGB signals from the Computer port can be output to an external monitor.

Note: Content you draw using the interactive features is not displayed on an external monitor unless

you draw it using Easy Interactive Tools.

Parent topic: Projector Connections

Connecting to External Speakers

To enhance the sound from your presentation, you can connect the projector to external self-powered

speakers. You can control the volume using the projector's remote control.

Note: You can also connect the projector to an amplifier with speakers.

If you want to output audio from the external speakers when the projector is turned off, you need to

select Communication On for the Standby Mode setting and Always On for the A/V Output setting in

the projector's menu system. You cannot play audio from the USB-B and LAN ports while the projector

is turned off.

Note: The projector's built-in speaker system is disabled when you connect external speakers.

1. Make sure your computer or video source is connected to the projector with both audio and video

cables as necessary.

2. Locate the appropriate cable to connect your external speakers, such as a stereo mini-jack-to-pin-

jack cable, or another type of cable or adapter.

3. Connect one end of the cable to your external speakers as necessary.

4. Connect the stereo mini-jack end of the cable to your projector's Audio Out port.

Parent topic: Projector Connections

Connecting to External USB Devices

Follow the instructions in these sections to connect external USB devices to the projector.

USB Device Projection

Connecting a USB Device or Camera to the Projector

Connecting a USB Device to the Control Pad or Projector

Selecting the Connected USB Source

Disconnecting a USB Device From the Control Pad or Projector

Parent topic: Projector Connections

USB Device Projection

You can project images and other content without using a computer or video device by connecting any of

these devices to your projector:

• USB flash drive

• Digital camera or smartphone

• USB hard drive

• Multimedia storage viewer

• USB memory card reader

Note: Digital cameras or smartphones must be USB-mounted devices, not TWAIN-compliant devices,

and must be USB Mass Storage Class-compliant.

Note: USB hard drives must meet these requirements:

• USB Mass Storage Class-compliant (not all USB Mass Storage Class devices are supported)

• Formatted in FAT or FAT32

• Self-powered by their own AC power supplies (bus-powered hard drives are not recommended)

• Avoid using hard drives with multiple partitions

You can project slide shows from image files on a connected USB device or memory card reader.

Parent topic: Connecting to External USB Devices

Connecting a USB Device or Camera to the Projector

You can connect your USB device or camera to the projector's USB-A port and use it to project images

and other content.

1. If your USB device came with a power adapter, plug the device into an electrical outlet.

2. Connect the USB cable (or USB flash drive or USB memory card reader) to the projector's USB-A

port shown here.

Note: Do not connect a USB hub or a USB cable longer than 10 feet (3 m), or the device may not

operate correctly.

3. Connect the other end of the cable (if applicable) to your device.

Parent topic: Connecting to External USB Devices

Connecting a USB Device to the Control Pad or Projector

You can connect your USB device to the USB-A port on the control pad or projector and use it to project

images and other content.

1. If your USB device came with a power adapter, plug the device into an electrical outlet.

2. Make sure a USB cable is connected between the USB-A port on the projector and the USB-B port

on the control pad.

3. Connect the USB cable for the device (or USB flash drive or USB memory card reader) into the

USB-A port on the bottom of the control pad.

4. Connect the other end of the cable (if applicable) to your device.

Note: You can also connect a USB device directly to the projector's USB-A port.

Parent topic: Connecting to External USB Devices

Selecting the Connected USB Source

You can switch the projector's display to the source you connected to the USB-A port on the control pad

or the projector.

1. Make sure the connected USB source is turned on, if necessary.

2. Press the Source Search button on the remote control or control pad, then select USB1.

Parent topic: Connecting to External USB Devices

Disconnecting a USB Device From the Control Pad or Projector

When you finish presenting with a connected USB device, you must prepare to disconnect the device

from the control pad or projector.

1. If the device has a power button, turn off and unplug the device.

2. Disconnect the USB device (or cable) from the control pad or projector.

Parent topic: Connecting to External USB Devices

Connecting a Printer to the Control Pad

You can connect an Epson printer or all-in-one device to the Printer port on the control pad and use it to

print your projected and annotated content from the whiteboard.

Note: Make sure the printer meets the control command requirements.

1. Make sure a USB cable is connected between the USB-A port on the projector and the USB-B port

on the control pad.

2. Connect another USB cable to the Printer port on the control pad. Make sure the cable is no longer

than 16.4 ft (5 m).

3. Connect the other end of the cable to the USB type B port on the printer.

Note: You can connect a wireless PCL6-compatible or Epson printer through the Whiteboard

Settings menu.

Supported Printer Types

Parent topic: Projector Connections

Related tasks

Selecting Whiteboard Print Settings

Supported Printer Types

You can connect to a printer with the type and command language described here.

Note: Scanning is only supported from Epson All-in-One printers over a USB connection.

Printer type Command language Scanner USB

connection

Network

connection

Single-

function

printer

ESC/Raster No Yes No

Single-

function

printer

ESC/P-R No Yes Yes

Multi-function

printer

ESC/Raster Yes Yes No

Multi-function

printer

ESC/P-R Yes Yes Yes

Laser ESC/Page, ESC/Page-

Color

No No Yes

Laser PCL6-compatible No No Yes

Parent topic: Connecting a Printer to the Control Pad

Related tasks

Selecting Whiteboard Print Settings

Connecting to a Document Camera

You can connect a document camera to your projector to project images viewed by the camera.

Depending on your Epson document camera model, do one of the following to connect the document

camera to your projector:

• For the Epson DC-06 document camera, locate the USB cable that came with the camera and

connect it to the to the projector's USB-A port and to the document camera's USB Type B port.

• For the Epson DC-11 document camera, connect it to the projector's Computer or Video port and to

the corresponding port on the document camera. See the document camera manual for details.

• For the Epson DC-12 document camera, connect it to the projector's HDMI,Computer, or Video port

and to the corresponding port on the document camera. See the document camera manual for details.

• For the Epson DC-20 document camera, connect it to the projector's HDMI,Computer, or Video port

and to the corresponding port on the document camera. See the document camera manual for details.

Note: For additional features supported by software, connect your document camera to your computer

instead of the projector. See the document camera manual for details.

Parent topic: Projector Connections

Connecting Multiple Projectors of the Same Model

If you use the interactive features of multiple projectors of the same model in the same room, you need

to synchronize the projectors. To do this, connect the optional remote control cable set (V12H005C28) to

the SYNC port on each projector.

1. Connect one end of the remote control cable to the SYNC In port on one projector, and connect the

other end to the SYNC Out port on the other projector.

Note: If you are connecting three or more projectors, connect the projectors in a chain as shown.

2. In the Extended menu, set the Sync of Projectors setting to Wired.

Note: If you are using the projector in the same room as another projector that does not support

cable connection, set the Wired Sync Mode setting to Mode 2 in the projector's Extended menu. If

you do not have the optional remote control cable, set the Distance of Projectors setting in the

projector's Extended menu to Mode 2.

Parent topic: Projector Connections

Installing Batteries in the Remote Control

The remote control uses the two AA batteries that came with the projector.

Caution: Use only the type of batteries specified in this manual. Do not install batteries of different types,

or mix new and old batteries.

1. Open the battery cover.

2. Insert the batteries with the +and –ends facing as shown.

3. Close the battery cover and press it down until it clicks into place.

Warning: Dispose of used batteries according to local regulations. Do not expose batteries to heat

or flame. Keep batteries out of the reach of children; they are choking hazards and are very

dangerous if swallowed.

Parent topic: Setting Up the Projector

Installing Batteries in the Pens

Each pen uses one AA battery.

1. Open the battery cover as shown.

2. Insert the battery with the +and –ends facing as shown.

3. Replace the battery cover and press it down until it clicks into place.

Parent topic: Setting Up the Projector

Installing Batteries in the Control Pad

The control pad uses two AA batteries.

Note: If you have the optional remote control cable set (ELPKC28), you can use it instead of batteries to

power the control pad.

1. Remove the top cover of the control pad by prying it off as shown.

2. Insert the batteries with the +and –ends facing as shown.

3. Replace the cover and press it down until it clicks into place.

Parent topic: Setting Up the Projector

Using the Projector on a Network

Follow the instructions in these sections to set up your projector for use on a network.

Wired Network Projection

Wireless Network Projection

Setting Up Projector Network E-Mail Alerts

Setting Up Monitoring Using SNMP

Controlling a Networked Projector Using a Web Browser

Creating an Address Book

Adding Templates from a Web Browser

Crestron RoomView Support

Wired Network Projection

You can send images to your projector through a wired network. To do this, you connect the projector to

your network, and then set up your projector and computer for network projection.

After connecting and setting up the projector as described here, install the network software from the

Epson Projector Software CD or download the software as necessary. Use the following software and

documentation to set up, control, and monitor network projection:

• EasyMP Network Projection software sets up your computer for network projection. See the EasyMP

Network Projection Operation Guide for instructions.

• EasyMP Monitor software (Windows only) lets you monitor and control your projector through the

network. You can download the latest software and documentation from the Epson web site. Go to

epson.com/support (U.S.) or epson.ca/support (Canada) and select your projector.

• Connect to a Network Projector (Windows 7 and Windows Vista only)

• EasyMP Multi PC Projection software allows you to hold interactive meetings by projecting the

computer screens of users over a network. See the EasyMP Multi PC Projection Operation Guide for

instructions.

• EasyMP Network Updater software (Windows only) allows you to update firmware for a projector over

a wired LAN. See the EasyMP Network Updater Operation Guide for instructions. You can download

the latest software and documentation from the Epson web site. Go to epson.com/support (U.S.) or

epson.ca/support (Canada) and select your projector.

Note: If your projector is connected via a LAN cable to a network that includes a wireless access point,

you can connect to the projector wirelessly through the access point using the EasyMP Network

Projection software.

Connecting to a Wired Network

Selecting Wired Network Settings

Parent topic: Using the Projector on a Network

Connecting to a Wired Network

To connect the projector to a wired local area network (LAN), use a 100Base-TX or 10Base-T network

cable. To ensure proper data transmission, use a Category 5 shielded cable or better.

1. Connect one end of the network cable to your network hub, switch, or router.

2. Connect the other end of the cable to the projector's LAN port.

Parent topic: Wired Network Projection

Selecting Wired Network Settings

Before you can project from computers on your network, you must select the network settings for the

projector using its menu system.

Note: Make sure you already connected the projector to your wired network using the LAN port.

1. Turn on the projector.

2. Press the Menu button.

3. Select the Network menu and press Enter.

4. Select Network Configuration and press Enter.

5. Select the Basic menu and press Enter.

6. Select the following basic options as necessary:

•Projector Name lets you enter a name up to 16 alphanumeric characters long to identify the

projector over the network.

•PJLink Password lets you enter a password up to 32 alphanumeric characters long for using the

PJLink protocol for projector control.

•Web Control Password or Web Remote Password lets you enter a password up to 8

alphanumeric characters long for accessing the projector over the web. (Default user name is

EPSONWEB; default password is admin.)

•Projector Keyword lets you turn on a security password to prevent access to the projector by

anyone not in the room with it. You must enter a displayed, randomized keyword from a computer

using the EasyMP Network Projection software to access the projector.

Note: Use the displayed keyboard to enter the name, passwords and keyword. Press the arrow

buttons on the remote control to highlight characters and press Enter to select them.

7. Select the Wired LAN menu and press Enter.

8. If necessary, select IP Settings and press Enter.

9. Select your IP Settings as necessary:

• If your network assigns addresses automatically, turn on the DHCP setting.

• If you must set addresses manually, turn off DHCP and enter the projector's IP Address,Subnet

Mask,DNS server,WINS server,and Gateway Address as needed. When manually entering IP

Settings, you cannot use restricted IP addresses.

Note: To highlight the numbers you want from the displayed keyboard, press the arrow buttons on

the remote control. To select a highlighted number, press Enter. Or, press and hold the Num button

on the remote control while entering the desired numbers.

10. To prevent display of the IP address on the standby screen, turn off IP Address Display.

11. When you finish selecting settings, select Complete or Setup Complete and follow the on-screen

instructions to save your settings and exit the menus.

Restricted IP Addresses

Parent topic: Wired Network Projection

Related references

Projector Network Settings - Network Menu

Restricted IP Addresses

When manually entering IP Settings, you cannot use certain ranges of IP addresses:

Setting Restricted IP addresses

IP Address 0.0.0.0

127.x.x.x

192.0.2.x

224.0.0.0 to 255.255.255.255

Subnet Mask 0.0.0.0

255.255.255.255

Gateway Address 0.0.0.0

197.x.x.x

224.0.0.0 to 255.255.255.255

DNS Server 127.x.x.x

192.0.2.x

224.0.0.0 to 255.255.255.255

Setting Restricted IP addresses

WINS Server 0.0.0.0

192.0.2.x

224.0.0.0 to 255.255.255.255

If you are not setting a WINS server, use 0.0.0.0.

Parent topic: Selecting Wired Network Settings

Wireless Network Projection

You can send images to your projector through a wireless network. To do this, you must install the

Epson 802.11b/g/n wireless LAN module, and then set up your projector and computer for wireless

projection.

Note: If your projector is connected via a LAN cable to a network that includes a wireless access point,

you can connect to the projector wirelessly using the EasyMP Network Projection software or other

supported Epson network software.

There are two ways to connect the projector to your wireless network:

• Using the optional Quick Wireless Connection USB Key (Windows only)

• Configuring the connection manually using the projector's Network menus

After installing the module and setting up the projector, install the network software from the Epson

Projector Software CD or download the software, as necessary. Use the following software and

documentation to set up, control, and monitor wireless projection:

• EasyMP Network Projection software sets up your computer for wireless network projection. See the

EasyMP Network Projection Operation Guide for instructions.

• EasyMP Monitor software (Windows only) lets you monitor and control your projector through the

network. You can download the latest software and documentation from the Epson web site. Go to

epson.com/support (U.S.) or epson.ca/support (Canada) and select your projector.

• EasyMP Multi PC Projection software allows you to hold interactive meetings by projecting the

computer screens of users over a network. See the EasyMP Multi PC Projection Operation Guide for

instructions.

• Projection from iOS or Android devices with the wireless LAN module and free Epson iProjection app;

visit epson.com/projectorapp (U.S.) or epson.ca/projectorapp (Canada) for more information.

Installing the Wireless LAN Module

Using Quick Wireless Connection (Windows Only)

Selecting Wireless Network Settings Manually

Selecting Wireless Network Settings in Windows

Selecting Wireless Network Settings in OS X

Enabling WPA or EAP Security

Parent topic: Using the Projector on a Network

Installing the Wireless LAN Module

To use the projector over a wireless network, install the Epson 802.11b/g/n wireless module in the

projector. Do not install any other type of wireless module.

Caution: Never remove the module while its indicator light is green or flashing, or while you are

projecting wirelessly. You may damage the module or lose data.

1. Turn off the projector and unplug the power cord.

2. Unscrew and remove the cable cover if it is attached (screwdriver not included).

3. Insert the wireless LAN module into the port shown here.

4. Replace the cable cover and tighten the screws.

5. Plug in and turn on the projector.

Parent topic: Wireless Network Projection

Using Quick Wireless Connection (Windows Only)

You can use the Quick Wireless Connection USB Key to quickly connect the projector to a Windows

computer wirelessly. Then you can project your presentation and remove the key when you are done.

Note: The Quick Wireless Connection USB Key is not included with your projector.

1. Turn on the projector.

2. Connect the USB key to the projector's USB-A port.

Note: If the control pad is connected to the projector, you can also connect the USB key to the USB-

Aport on the control pad, as shown:

You see a projected message that the network information update is complete.

3. Remove the USB key.

4. Connect the USB key to a USB port on your computer or laptop.

Note: In Windows Vista, if you see the AutoPlay window, select Run LaunchU3.exe, then select

Allow on the next screen.

5. Follow the on-screen instructions to install the Quick Wireless Connection driver.

Note: If you see a Windows Firewall message, click Yes to disable the firewall.

After a few minutes, your computer image is displayed by the projector. If it does not appear, press

the Source Search button on your remote control and select the LAN source, or restart your

computer.

6. Run your presentation as necessary.

7. When you finish projecting wirelessly, select the Safely Remove Hardware option in the Windows

taskbar, then remove the USB key from your computer.

Note: You may need to restart your computer to reactivate your wireless LAN connection.

Parent topic: Wireless Network Projection

Selecting Wireless Network Settings Manually

Before you can project from your wireless network, you must select the network settings for the projector

using its menu system.

1. Turn on the projector.

2. Press the Menu button.

3. Select the Network menu and press Enter.

4. Select Network Configuration and press Enter.

5. Select the Basic menu and press Enter.

6. Select the following basic options as necessary:

•Projector Name lets you enter a name up to 16 alphanumeric characters long to identify the

projector over the network.

•Web Remote Password lets you enter a password up to 8 alphanumeric characters long for

accessing the projector over the web.

•Projector Keyword lets you turn on a security password to prevent access to the projector by

anyone not in the room with it. You must enter a displayed, randomized keyword from a computer

using the EasyMP Network Projection software to access the projector.

Note: Use the displayed keyboard to enter the name, passwords and keyword. Press the arrow

buttons on the remote control to highlight characters and press Enter to select them.

7. Select the Wireless LAN menu and press Enter.

8. Select the settings on the Wireless LAN menu as necessary for your network.

9. When you finish selecting settings, select Setup complete and follow the on-screen instructions to

save your settings and exit the menus.

After you complete the wireless settings for your projector, you need to select the wireless network on

your computer.

Wireless LAN Menu Settings

Parent topic: Wireless Network Projection

Wireless LAN Menu Settings

Setting Options Description

Wireless LAN Power On

Off

Turns wireless LAN support on

and off

Wi-Fi Protected Setup To Setup Wizard Select To Setup Wizard to start

the WPS Connection Setup utility

Setting Options Description

Wireless LAN System 802.11b/g

802.11b/g/n

Sets the type of wireless LAN

system the projector is

connecting to

Connection Mode Quick

Advanced

Selects the type of wireless

connection:

Quick: lets you quickly connect

to one computer or use the

optional Quick Wireless

Connection USB key to connect.

If the SSID Auto Setting is set to

On, the projector becomes an

easy access point. If SSID Auto

Setting is set to Off, the network

is created in Ad hoc mode.

Advanced: lets you connect to

multiple computers via a wireless

network access point

(infrastructure mode)

SSID Auto Setting On

Off

Turns on automatic SSID

searching in Quick connection

mode; set to Off when

connecting to multiple projectors

at the same time

SSID Up 32 alphanumeric characters Sets the SSID (network name) of

the wireless LAN system the

projector is connecting to

Search Access Point To Search View Search for available wireless

network access points in

Advanced connection mode

Channel 1ch

6ch

11ch

In Quick connection mode,

selects the frequency band

(channel) used by the wireless

LAN

Setting Options Description

SSID Display On

Off

Selects whether to display the

SSID on the network standby

screen

DHCP On

Off

Turns on DHCP if your network

assigns addresses automatically;

set to Off to manually enter the

network's IP Address,Subnet

Mask, and Gateway Address

DNS Server IP address Sets the IP address for the DNS

server. The DNS server resolves

the host name entered during

email configuration

WINS server IP address Sets the IP address for the

network folder where images are

saved; this setting is used

(instead of the UNC address)

when the folder is on a different

network segment from the

projector

IP Address Display On

Off

Selects whether to display the IP

address on the network standby

screen

Parent topic: Selecting Wireless Network Settings Manually

Selecting Wireless Network Settings in Windows

Before connecting to the projector, select the correct wireless network on your computer.

1. To access your wireless utility software, double-click the network icon on the Windows taskbar.

2. Do one of the following:

• If your projector is set up on an existing network (Advanced mode), select the network name

(SSID).

• If your projector is configured for Quick mode, select the projector's SSID.

3. Click Connect.

Parent topic: Wireless Network Projection

Selecting Wireless Network Settings in OS X

Before connecting to the projector, select the correct wireless network in OS X.

1. Click the AirPort icon on the menu bar at the top of the screen.

2. Make sure AirPort is turned on, then do one of the following:

• If your projector is set up on an existing network (Advanced mode), select the network name

(SSID).

• If your projector is configured for Quick mode, select the projector's SSID.

Parent topic: Wireless Network Projection

Enabling WPA or EAP Security

Set up the WPA or EAP security settings to match your network's settings. Check with your network

administrator for guidance on entering the correct information.

1. Select a WPA or EAP setting from the drop-down menu.

2. Select the settings on the security menu as necessary for your network.

3. When you finish selecting settings, select Setup complete and follow the on-screen instructions to

save your settings and exit the menus.

Wireless Security Menu Settings

Parent topic: Wireless Network Projection

Wireless Security Menu Settings

Settings on the Security menu let you select the type of security and security settings that match the

network you are connecting the projector to.

Setting Options Description

Security Open

WPA/WPA2-PSK

WPA/WPA2-EAP

Selects the type of security used

on the wireless network

Passphrase Various passphrases from 8 to

63 characters

For WPA/WPA2-PSK security,

selects the pre-shared

passphrase used on the network

Note: You can enter up to 32

characters in the projector menu.

To input more than 32

characters, use your Web

browser.

In Quick mode, the initial

passphrase is hidden. Change

the passphrase to connect using

Epson iProjection.

EAP Method PEAP

PEAP-TLS

EAP-TLS

EAP-Fast

LEAP

For WPA/WPA2-EAP security,

selects the protocol for

authentication

Setting Options Description

User name Various user names up to 64

characters

For WPA/WPA2-EAP security,

selects the user name;

automatically detected when

using the PEAP-TLS or EAP-

TLS EAP methods

Note: You can enter up to 32

characters in the projector menu.

To input more than 32

characters, use your Web

browser.

Password Various passwords up to 64

characters

For WPA/WPA2-EAP security,

selects the password for EAP

authentication

Note: You can enter up to 32

characters in the projector menu.

To input more than 32

characters, use your Web

browser.

Client Certificate — For WPA/WPA2-EAP security,

displays the certificate's Issued

to,Issued by, and Validity

period if a client certificate has

been set

Verify Server Certificate On

Off

For WPA/WPA2-EAP security,

selects whether to verify the

server certificate when a CA

certificate has been set

CA certificate — For WPA/WPA2-EAP security,

displays the certificate's Issued

to,Issued by, and Validity

period if a CA certificate has

been set

100

Setting Options Description

Setting RADIUS Server Name On

Off

For WPA/WPA2-EAP security,

selects whether to verify the

authentication server name

during certificate verification

RADIUS Server Name Various server names up to 32

characters

For WPA/WPA2-EAP security,

selects the server name to verify

Verify Exp. date of Server Cert. On

Off

For WPA/WPA2-EAP security,

selects whether to verify the

server certificate's validity period

during certificate verification

Parent topic: Enabling WPA or EAP Security

Setting Up Projector Network E-Mail Alerts

You can set up the projector to send you an e-mail alert over the network if there is a problem with the

projector.

1. Press the Menu button.

2. Select the Network menu and press Enter.

3. Select Network Configuration and press Enter.

101

4. Select the Administrator Settings menu and press Enter, then select Mail Notification and press

Enter.

5. Enter the IP address for the SMTP Server option.

Note: Do not use these addresses: 127.x.x.x or 224.0.0.0 through 255.255.255.255 (where x is a

number from 0 to 255).

6. Select a number for the SMTP server Port Number, from 1 to 65535 (default is 25).

7. Choose an Email Address field, enter the e-mail address, and select the alerts you want to receive

there. Repeat for up to three addresses.

Note: Your e-mail address can be up to 32 alphanumeric characters long.

8. When you finish selecting settings, select Setup Complete and follow the on-screen instructions to

save your settings and exit the menus.

Note: If a critical problem causes the projector to shut down, you may not receive an e-mail alert.

Network Projector E-mail Alert Messages

102

Parent topic: Using the Projector on a Network

Network Projector E-mail Alert Messages

When a problem occurs with a networked projector, and you selected to receive e-mail alerts, you

receive an e-mail containing the following information:

•Epson Projector on the subject line

• The name of the projector experiencing a problem

• The IP address of the affected projector

• Detailed information about the problem

Note: If a critical problem causes a projector to shut down, you may not receive an e-mail alert.

Parent topic: Setting Up Projector Network E-Mail Alerts

Setting Up Monitoring Using SNMP

Network administrators can install SNMP (Simple Network Management Protocol) software on network

computers so they can monitor projectors. If your network uses this software, you can set up the

projector for SNMP monitoring.

1. Press the Menu button.

2. Select the Network menu and press Enter.

3. Select Network Configuration and press Enter.

103

4. Select the Administrator Setting menu and press Enter, then select the SNMP menu and press

Enter.

5. Enter up to two IP addresses to receive SNMP notifications, using 0 to 255 for each address field.

Note: Do not use these addresses: 127.x.x.x or 224.0.0.0 through 255.255.255.255 (where x is a

number from 0 to 255).

6. Enter the community name of SNMP (up to 32 single-byte alphanumeric characters).

7. When you finish selecting settings, select Setup Complete and follow the on-screen instructions to

save your settings and exit the menus.

Parent topic: Using the Projector on a Network

Controlling a Networked Projector Using a Web Browser

Once you have connected your projector to your network, you can select projector settings and control

projection using a compatible web browser. This lets you access the projector remotely.

Note: The web setup and control features support Microsoft Internet Explorer 8.0 or later, and Safari on

networks that do not use a proxy server for connection. You cannot select all of the projector menu

settings or control all projector functions using a web browser.

104

Note: If you want to use a web browser to select settings when the projector is turned off, you need to

adjust the Standby Mode settings in the ECO menu.

1. Make sure the projector is turned on.

2. Start your web browser on a computer connected to the network.

3. Type the projector's IP address into the browser's address box and press the computer's Enter key.

You see the Web Control screen and a prompt to enter a user ID and password.

4. Enter the following information in uppercase or lowercase letters, exactly as shown:

• For the user ID, enter EPSONWEB. (You cannot change the user ID.)

• For the password, enter the default password admin. (You can change the Web Control password

using the projector's Network menu.)

5. To select projector menu settings, select the name of the menu and follow the on-screen instructions

to select settings.

6. To control projection remotely, select the Web Remote option.

Note: If the Web Remote Password is set to On, the user ID for the remote is EPSONREMOTE.

You see this screen:

1 Power button control

105

2 Captures the projected image. Switch to whiteboard mode to paste the image into a new

page.

3 Prints the projected image.

4Freeze button control

5A/V Mute button control

6Page Up and Page Down button controls

7 Searches for sources

8 Switches to whiteboard mode.

9 Saves the projected image in .webp format.

10 Volume button controls

11 Closed Caption control

7. Select the icon corresponding to the projector function you want to control.

Parent topic: Using the Projector on a Network

Related references

Wireless Security Menu Settings

Creating an Address Book

When sending e-mails from whiteboard mode, you can choose e-mail addresses from an address book .

You can create the address book by loading a text file of up to 999 addresses through the web control

page.

Note: Addresses are displayed in the order they appear in the text file.

1. Create the text file containing the list of addresses you want to add to the address book. The file

must have the following characteristics:

• Tab-delimited

• Each line must contain a pair of strings separated by a tab: <name> <tab> <email_address>

• Filename with a .txt extension

• Character code must be Unicode

An example of a text file:

106

2. Open a web browser and connect to the projector by entering the IP address of the projector.

Note: You can find the projector's IP address in the projector's Network menu.

3. Enter the user name and password at the prompts.

4. Select the config icon.

Note: This icon does not appear when you connect from a computer.

The Web Control page is displayed.

5. Select Whiteboard Settings >Administrator Settings >Address Book Settings >Address

Book File and select the Choose File button.

6. Select the address book file and select Set.

The address book file is uploaded to the projector.

7. To delete the address book, select Whiteboard Settings >Administrator Settings >Address

Book Settings >Delete Address Book and select Set.

Parent topic: Using the Projector on a Network

Related references

Projector Network Settings - Network Menu

Adding Templates from a Web Browser

You can use a web browser to add templates for use in Whiteboard mode. You can add up to 5 images,

which must be in .webp format to be used as templates.

1. Make sure the projector is turned on.

2. Start your web browser on a computer connected to the network.

3. Type the projector's IP address into the browser's address box and press the computer's Enter key.

You see the Web Control screen and a prompt to enter a user ID and password.

4. Enter the following information in uppercase or lowercase letters, exactly as shown:

• For the user ID, enter EPSONWEB. (You cannot change the user ID.)

107

• For the password, enter the default password admin. (You can change the Web Control password

using the projector's Network menu.)

5. Under Whiteboard Settings, select Administrator Settings.

You see a screen like this:

6. Under Template Settings, select the number of the template you are uploading.

7. Select the Browse button, select the .webp image on your computer, and select Open.

8. Select Set to upload the template to the projector.

Parent topic: Using the Projector on a Network

Crestron RoomView Support

If you are using the Crestron RoomView network monitoring and control system, you can set up your

projector for use on the system. Crestron RoomView lets you control and monitor your projector using a

web browser.

Note: You cannot use the Epson Web Control feature or the Message Broadcasting plug-in for EasyMP

Monitor when you use Crestron RoomView.

For additional information on Crestron RoomView, contact Crestron.

108

Setting Up Crestron RoomView Support

Controlling a Networked Projector Using Crestron RoomView

Parent topic: Using the Projector on a Network

Setting Up Crestron RoomView Support

To set up your projector for monitoring and control using a Crestron RoomView system, make sure your

computer and projector are connected to the network.

Note: If you want to use the Crestron RoomView system when the projector is turned off, you need to

adjust the Standby Mode settings in the ECO menu.

1. Press the Menu button.

2. Select the Network menu and press Enter.

3. Select Network Configuration and press Enter.

4. Select the Administrator Setting menu and press Enter.

5. Set the Crestron RoomView setting to On to allow the projector to be detected.

6. Turn off the projector, then turn it on again to enable the setting.

109

Parent topic: Crestron RoomView Support

Controlling a Networked Projector Using Crestron RoomView

Once you have set up your projector to use Crestron RoomView, you can control and monitor projection

using a compatible web browser.

1. Start your web browser on a computer connected to the network.

2. Type the projector's IP address into the browser's address box and press the computer's Enter key.

You see this screen:

3. Select the input source that you want to control in the Sources List box. You can scroll through

available sources using the up and down arrows in the box.

4. To control projection remotely, click the on-screen buttons that correspond to the projector's remote

control buttons. You can scroll through button options at the bottom of the screen.

Note: These on-screen buttons do not directly correspond to the projector's remote control buttons:

•OK acts as the Enter button

•Menu displays the projector's menu

5. To view information about the projector, click the Info tab.

6. To change projector, Crestron, and password settings, click the Tools tab, select settings on the

displayed screen, and click Send.

110

7. When you finish selecting settings, click Exit to exit the program.

Parent topic: Crestron RoomView Support

111

Using Basic Projector Features

Follow the instructions in these sections to use your projector's basic features.

Turning On the Projector

Turning Off the Projector

Selecting the Language for the Projector Menus

Setting the Date and Time

Image Shape

Resizing the Image with the Wide and Tele Buttons

Adjusting the Image Position

Focusing the Image

Remote Control Operation

Selecting an Image Source

Projection Modes

Image Aspect Ratio

Color Mode

Controlling the Volume with the Volume Buttons

Projecting a PC Free Presentation

Turning On the Projector

Turn on the computer or video equipment you want to use before you turn on the projector so it can

display the image source.

112

1. Connect the power cord to the projector's power inlet.

2. Plug the power cord into an electrical outlet.

Note: With Direct Power On turned on, the projector turns on as soon as you plug it in.

The projector's power light turns blue. This indicates that the projector is receiving power.

3. Press the power button on the projector or the remote control to turn on the projector.

The projector beeps and the Status light flashes blue as the projector warms up. Once the projector

is warmed up, the Status light stops flashing and turns blue.

Warning: Never look into the projector lens when the lamp is on. This can damage your eyes and is

especially dangerous for children.

113

If you do not see a projected image right away, try the following:

• Turn on the connected computer or video device.

• Press the Source Search button on the projector or remote control to detect the video source.

Parent topic: Using Basic Projector Features

Related references

Projector Setup Settings - Extended Menu

Turning Off the Projector

Before turning off the projector, shut down any computer connected to it so you can see the computer

display during shutdown.

Note: Turn off this product when not in use to prolong the life of the projector. Lamp life will vary

depending upon mode selected, environmental conditions, and usage. Brightness decreases over time.

Note: When using the A/V Mute feature, the projector lamp is still on. To turn off the lamp, turn off the

projector.

1. Press the power button on the projector or the remote control.

The projector displays a shutdown confirmation screen.

2. Press the power button again. (To leave it on, press any other button.)

The projector beeps twice, the lamp turns off, and the Status light turns off.

Note: With Epson's Instant Off technology, there is no cool-down period so you can pack up the

projector for transport right away (if necessary).

114

Caution: Do not turn the projector on immediately after turning it off. Turning the projector on and off

frequently may shorten the life of the lamp.

3. To transport or store the projector, make sure the Status light is off, then unplug the power cord.

Caution: To avoid damaging the projector or lamp, never unplug the power cord when the Status

light is on or flashing.

Parent topic: Using Basic Projector Features

Selecting the Language for the Projector Menus

If you want to view the projector's menus and messages in another language, you can change the

Language setting.

1. Turn on the projector.

2. Press the Menu button.

115

3. Select the Extended menu and press Enter.

4. Select the Language setting and press Enter.

5. Select the language you want to use and press Enter.

6. Press Menu or Esc to exit the menus.

Parent topic: Using Basic Projector Features

Related references

Projector Setup Settings - Extended Menu

Setting the Date and Time

You must set the projector's date and time to schedule projector events and use wireless LAN

authentication.

1. Press the Menu button.

2. Select the Extended menu and press Enter.

3. Select the Time/Schedule Settings setting and press Enter.

116

The Schedule Settings screen appears.

4. Select the Date & Time setting and press Enter.

5. Do one of the following:

• Enter the date and time settings using the on-screen keyboard.

• Select On as the Use Internet Time setting and enter the IP address for the time server in the

Internet Time Server field.

6. Select Change DST Settings and select the Daylight Savings Time setting for your location.

7. When you are finished, press the Esc button.

8. Select Setup complete and select Yes to save your changes.

117

Parent topic: Using Basic Projector Features

Related tasks

Enabling WPA or EAP Security

Related topics

Scheduling Projector Events

Image Shape

You can project an evenly rectangular image by placing the projector directly in front of the center of the

screen and keeping it level. If you place the projector at an angle to the screen, or tilted up or down, or off

to the side, you may need to correct the image shape for the best display quality.

Note: For interactive use, the image must be evenly rectangular, without distortion.

Correcting Image Shape with the Keystone Buttons

Correcting Image Shape with Quick Corner

Parent topic: Using Basic Projector Features

Correcting Image Shape with the Keystone Buttons

You can use the projector's keystone correction buttons to correct the shape of an image that is

unevenly rectangular on the sides.

Note: For interactive use, make sure the degree of horizontal and vertical keystone correction is no more

than ± 3°.

1. Turn on the projector and display an image.

Note: You can display a pattern to aid in adjusting the projected image using the Settings menu.

Note: You can also display the pattern by pressing the User button on the remote control (if the test

pattern is assigned to this button).

118

2. Press one of these keystone buttons on the control panel to display the Keystone adjustment

screen.

119

3. Press a keystone button on the projector's control panel to adjust the image shape.

Note: The horizontal keystone adjustment buttons are labeled Wide and Tele.

After correction, your image is slightly smaller.

Note: If the projector is installed out of reach, you can also correct the image shape with the remote

control using the Keystone settings in the projector menus.

Parent topic: Image Shape

120

Correcting Image Shape with Quick Corner

You can use the projector's Quick Corner setting to correct the shape and size of an image that is

unevenly rectangular on all sides.

1. Turn on the projector and display an image.

Note: You can display a pattern to aid in adjusting the projected image using the Settings menu.

Note: You can also display the pattern by pressing the User button on the remote control (if the test

pattern is assigned to this button).

2. Press the Menu button.

3. Select the Settings menu and press Enter.

4. Select the Keystone setting and press Enter.

5. Select the Quick Corner setting and press Enter. Then press Enter again.

121

You see the Quick Corner adjustment screen:

6. Use the arrow buttons on the projector or the remote control to select the corner of the image you

want to adjust. Then press Enter.

7. Press the arrow buttons to adjust the image shape as necessary.

8. When you are finished, press Esc.

Note: Using Quick Corner can affect the accuracy of the interactive pens.

Parent topic: Image Shape

Resizing the Image with the Wide and Tele Buttons

1. Turn on the projector and display an image.

2. To enlarge the image size, press the Wide button on the projector's control panel.

122

3. To reduce the image size, press the Tele button.

After you adjust the image size, the Image Shift screen is displayed automatically for adjusting the

image position.

Note: If the projector is installed out of reach, you can also adjust the image size with the remote

control using the Zoom setting in the projector menus.

Parent topic: Using Basic Projector Features

Related references

Projector Feature Settings - Settings Menu

Adjusting the Image Position

You can use the Image Shift feature to adjust the image position without moving the projector.

Note: This feature is not available if the Zoom option is set to the widest setting.

123

1. Turn on the projector and display an image.

2. Adjust the image size using the Wide and Tele buttons.

After you adjust the image size, the Image Shift screen is displayed automatically.

3. Use the arrow buttons on the projector or remote control to adjust the image position.

Note: You can also use the Settings menu to adjust the Image Shift setting.

Parent topic: Using Basic Projector Features

Related references

Projector Feature Settings - Settings Menu

Focusing the Image

1. Turn on the projector and display an image.

Note: You can display a pattern to aid in adjusting the projected image using the Settings menu.

2. Slide the switch to open the air filter cover on the side of the projector.

124

3. Raise or lower the focus lever to sharpen the image.

Parent topic: Using Basic Projector Features

Related references

Projector Feature Settings - Settings Menu

Remote Control Operation

The remote control lets you control the projector from almost anywhere in the room, up to 19.7 feet (6 m)

away. You can point it at the screen or board, or the front or back of the projector.

125

Make sure that you aim the remote control at the projector's receivers within the angles listed here.

1 19.7 feet (6 m)

2 ± 30°

3 ± 55°

4 60°

5 75°

6 15°

Note: Avoid using the remote control in conditions with bright fluorescent lights or in direct sunlight, or

the projector may not respond to commands. If you will not use the remote control for a long time,

remove the batteries.

Using the Remote Control as a Wireless Mouse

Using the Remote Control as a Pointer

Parent topic: Using Basic Projector Features

126

Using the Remote Control as a Wireless Mouse

You can use the projector's remote control as a wireless mouse so you can control projection at a

distance from the computer.

Note: This feature cannot be used at the same time as the interactive pens. If you want to use the

remote control as a wireless mouse, you need to change the USB Type B setting in the projector's

Extended menu.

1. Connect the projector to a computer using the projector's USB-B,Computer, or HDMI port to

display video.

Note: You cannot use the wireless mouse feature with an MHL connection.

2. If you connected your computer to the Computer or HDMI port, also connect a USB cable to the

projector's USB-B port and to a USB port on your computer (for wireless mouse support).

3. Start your presentation.

4. Use the following buttons on the remote control to control your presentation:

• To move through slides or pages, press the up or down Page buttons.

• To move the cursor on the screen, use the arrow buttons.

• To left-click, press the button once (press it twice to double-click).

• To right-click, press the Esc button.

• To drag-and-drop, hold the button as you move the cursor with the arrow buttons, then release

at the destination.

127

Parent topic: Remote Control Operation

Using the Remote Control as a Pointer

You can use the projector's remote control as a pointer to help you call out important information on the

screen. The default pointer shape is an arrow, but you can select an alternative shape using the Settings

menu.

1. Press the Pointer button on the remote control.

2. Use the arrow buttons on the remote control to move the pointer on the screen.

3. Press Esc to clear the pointer from the screen.

Parent topic: Remote Control Operation

Selecting an Image Source

If you connected multiple image sources to the projector, such as a computer and DVD player, you may

want to switch from one image source to the other.

1. Make sure the connected image source you want to use is turned on.

2. For video image sources, insert a DVD or other video media and press its play button, if necessary.

128

3. Press the Source Search button on the projector, remote control, or control pad, then select the

source you want.

Parent topic: Using Basic Projector Features

Related tasks

Selecting a Networked Device Source

Projection Modes

Depending on how you positioned the projector, you may need to change the projection mode so your

images project correctly.

•Front lets you project from a table in front of the screen.

129

•Front/Upside Down (default setting) flips the image over top-to-bottom to project upside-down from a

wall or ceiling mount. This mode should also be used when you mount the projector vertically on a

table to create an interactive work surface.

•Rear flips the image horizontally to project from behind a translucent screen.

•Rear/Upside Down flips the image over top-to-bottom and horizontally to project from the wall or

ceiling and behind a translucent screen.

Note: The two Rear modes cannot be used with the interactive pens.

You can change the projection mode using the remote control or by changing the Projection setting in

the Extended menu.

Changing the Projection Mode Using the Remote Control

Changing the Projection Mode Using the Menus

Parent topic: Using Basic Projector Features

Related references

Projector Setup Settings - Extended Menu

Changing the Projection Mode Using the Remote Control

You can change the projection mode to flip the image over top-to-bottom.

1. Turn on the projector and display an image.

2. Hold down the A/V Mute button on the remote control for five seconds.

The image disappears briefly and reappears flipped top-to-bottom.

3. To change projection back to the original mode, hold down the A/V Mute button for five seconds

again.

130

Parent topic: Projection Modes

Changing the Projection Mode Using the Menus

You can change the projection mode to flip the image over top-to-bottom and/or left-to-right using the

projector menus.

1. Turn on the projector and display an image.

2. Press the Menu button.

3. Select the Extended menu and press Enter.

4. Select the Projection setting and press Enter.

5. Select a projection mode and press Enter.

6. Press Menu or Esc to exit the menus.

Parent topic: Projection Modes

Related references

Projector Setup Settings - Extended Menu

Image Aspect Ratio

The projector can display images in different width-to-height ratios called aspect ratios. Normally the

input signal from your video source determines the image's aspect ratio. However, for certain images

you can change the aspect ratio to fit your screen by pressing a button on the remote control.

131

If you always want to use a particular aspect ratio for a certain video input source, you can select it using

the projector's menus.

Changing the Image Aspect Ratio

Available Image Aspect Ratios

Parent topic: Using Basic Projector Features

Changing the Image Aspect Ratio

You can change the aspect ratio of the displayed image to resize it.

1. Turn on the projector and switch to the image source you want to use.

2. Press the Aspect button on the remote control.

The shape and size of the displayed image changes, and the name of the aspect ratio appears

briefly on the screen.

3. To cycle through the available aspect ratios for your input signal, press the Aspect button

repeatedly.

Parent topic: Image Aspect Ratio

Available Image Aspect Ratios

You can select the following image aspect ratios, depending on the input signal from your image source.

Note: Black bands and cropped images may project in certain aspect ratios, depending on the aspect

ratio and resolution of your input signal.

132

Aspect ratio setting Description

Auto Automatically sets the aspect ratio according to the input signal and

the Resolution setting.

Normal Displays images using the full projection area and maintains the

aspect ratio of the image.

16:9 Converts the aspect ratio of the image to 16:9.

Full Displays images using the full width of the projection area, but does

not maintain the aspect ratio.

Zoom Displays images using the full width of the projection area and

maintains the aspect ratio of the image.

Native Displays images as is (aspect ratio and resolution are maintained).

Note: The Auto aspect ratio setting is available only for HDMI image sources.

Parent topic: Image Aspect Ratio

Color Mode

The projector offers different Color Modes to provide optimum brightness, contrast, and color for a

variety of viewing environments and image types. You can select a mode designed to match your image

and environment, or experiment with the available modes.

If you always want to use a particular color mode for a certain video input source, you can select it using

the projector menus.

Changing the Color Mode

Available Color Modes

Turning On Auto Iris

Parent topic: Using Basic Projector Features

Changing the Color Mode

You can change the projector's Color Mode using the remote control to optimize the image for your

viewing environment.

1. Turn on the projector and switch to the image source you want to use.

2. If you are projecting from a DVD player or other video source, insert a disc or other video media and

press the play button, if necessary.

133

3. Press the Color Mode button on the remote control to change the Color Mode.

The image appearance changes and the name of the Color Mode appears briefly on the screen.

4. To cycle through all the available Color Modes for your input signal, press the Color Mode button

repeatedly.

Parent topic: Color Mode

Available Color Modes

You can set the projector to use these Color Modes, depending on the input source you are using:

Color Mode Description

Dynamic Best for video games in a bright room

Presentation Best for color presentations in a bright room

Theatre Best for movies projected in a dark room

Photo Best for still images projected in a bright room

Sports Best for television images in a bright room

sRGB Best for standard sRGB computer displays

Whiteboard Best for presentations onto a whiteboard (adjusts the colors

accordingly)

DICOM SIM Best for projecting X-rays and other medical images (shows clear

shadows)

Customized Best for customizing a color mode using manual RGBCMY

settings in the Image > Advanced menu

134

Note: The projector is not a medical device and cannot be used for medical diagnosis.

Parent topic: Color Mode

Related references

Image Quality Settings - Image Menu

Turning On Auto Iris

In certain color modes, you can turn on the Auto Iris setting to automatically optimize the image based on

the brightness of the content you project.

1. Turn on the projector and switch to the image source you want to use.

2. Press the Menu button.

3. Select the Image menu and press Enter.

4. Select the Auto Iris setting and choose one of the following:

•High Speed to adjust brightness as soon as the scene changes.

•Normal for standard brightness adjustment.

Note: You can set Auto Iris for each Color Mode that supports the feature. You cannot change the

Auto Iris setting when you are using a Closed Caption setting.

5. Press Menu or Esc to exit the menus.

135

Parent topic: Color Mode

Controlling the Volume with the Volume Buttons

You can use the Volume buttons on the remote control to adjust the volume as you project a

presentation with audio. The volume buttons control the projector’s internal speaker system or any

external speakers you connected to the projector.

You must adjust the volume separately for each connected input source.

1. Turn on the projector and start a presentation that includes audio.

2. To lower or raise the volume, press the Volume buttons on the remote control.

A volume gauge appears on the screen.

3. To set the volume to a specific level for an input source, use the projector menus.

Parent topic: Using Basic Projector Features

Projecting a PC Free Presentation

You can use your projector's PC Free feature whenever you connect a USB device that contains

compatible image or movie files. This lets you quickly and easily display and control them using the

projector's remote control. You can also display a slide show of the images.

Supported PC Free File Types

Starting a PC Free Slide Show

Starting a PC Free Movie Presentation

Starting a PC Free PDF File Presentation

Slideshow Display Options

Parent topic: Using Basic Projector Features

136

Supported PC Free File Types

You can project these types of files using the projector's PC Free feature.

Note: For best results, place your files on media that is formatted in FAT16/32. If you have trouble

projecting from media formatted for non-Windows file systems, try formatting the media for Windows

instead. You may not be able to use the security features on certain USB storage devices with PC Free

features. When connecting a USB-compatible hard drive, connect the AC adapter supplied with the

drive.

Graphic and Text File Formats

File contents File type

(extension)

Details

Image .jpg Make sure the file is not:

• CMYK format

• Progressive format

• Highly compressed

• Above 8192 × 8192 resolution

• Over 12MB in size

• Named with a .jpeg extension

.bmp Make sure the file resolution is not above 2048 × 2048

.gif Make sure the file is not:

• Above 2048 × 2048 resolution

• Animated

.webp Make sure the file resolution is not above 2048 × 2048

PDF .pdf Make sure the file is not:

• Saved in PDF version 1.7 or earlier format

• Encrypted

Movie File Formats

137

File type

(extension)

Movie codec Audio codec Recording quality

.mpg MPEG-2 MPEG-1 Layer 1/2

You can play back MPEG

contents with no audio.

You cannot play back audio

from Linear PCM and AC-3

content.

Make sure the file is not

named with an .mpeg

extension.

Maximum bit rate: 12 Mbps

Maximum resolution: 1280 ×

720

.mp4 MPEG-4 ASP

MPEG-4 AVC

MPEG-4 AAC-LC

.wmv WMV9 WMA

.avi Motion JPEG Linear PCM

ADPCM

Note: For best results, do not use a USB storage device with a slow access speed or the movies may

not play back correctly. You cannot project files to which DRM (Digital Rights Management) is applied.

Parent topic: Projecting a PC Free Presentation

Starting a PC Free Slide Show

After connecting a USB device or digital camera to the projector, you can switch to the USB input source

and start your slide show.

Note: You can change the PC Free operation options or add special effects by highlighting Option at the

bottom of the screen and pressing Enter.

1. Press the Source Search button on the projector, remote control, or Control Pad, or tap the Source

Select icon on the whiteboard.

2. Select the USB1 source.

138

The PC Free screen appears.

3. Do the following as necessary to locate your files:

• If you need to display files inside a subfolder on your device, press the arrow buttons to highlight

the folder and press the Enter button.

• To move back up a folder level on your device, highlight Back to Top and press Enter.

• To view additional files in a folder, highlight Next page or Previous page and press Enter, or

press the Page up or down buttons on the remote control.

4. Do one of the following:

• To display an individual image, press the arrow buttons to highlight the image and press Enter.

(Press the Esc button to return to the file list screen.)

• To display a slide show of all the images in a folder, press the arrow buttons to highlight the

Slideshow option at the bottom of the screen and press Enter.

Note: If any file names are longer than 8 characters or include unsupported symbols, the file names

may be shortened or changed only in the screen display.

139

5. While projecting, use the following commands to control the display as necessary:

• To rotate a displayed image, press the up or down arrow button.

• To move to the next or previous image, press the left or right arrow button.

6. To stop the display, follow the on-screen instructions or press the Esc button.

Parent topic: Projecting a PC Free Presentation

Starting a PC Free Movie Presentation

After connecting a USB device or digital camera to the projector, you can switch to the USB input source

and start your movie.

Note: You can change the PC Free operation options by highlighting Option at the bottom of the screen

and pressing Enter.

1. Press the Source Search button on the projector, remote control, or Control Pad, or tap the Source

Select icon on the whiteboard. Select the USB1 source.

The PC Free screen appears.

140

2. Do the following as necessary to locate your files:

• If you need to display files inside a subfolder on your device, press the arrow buttons to highlight

the folder and press the Enter button.

• To move back up a folder level on your device, highlight Back to Top and press Enter.

• To view additional files in a folder, highlight Next page or Previous page and press Enter, or

press the Page up or down buttons on the remote control.

3. To play back a movie, press the arrow buttons to highlight the file and press Enter.

Note: If any file names are longer than 8 characters or include unsupported symbols, the file names

may be shortened or changed only in the screen display. If you want to play back all the movies in a

folder in sequence, select the Slideshow option at the bottom of the screen.

4. To stop movie playback, press the Esc button, highlight Exit, and press Enter.

Parent topic: Projecting a PC Free Presentation

Starting a PC Free PDF File Presentation

After connecting a USB device to the projector, you can switch to the USB input source and start your

PDF file presentation.

Note: You cannot do the following while presenting a PDF file from a USB device:

• Release a password

• Display e-signatures, JPEG2000 images, transparent effects, 3D artwork, or comments

• Play multimedia content

1. Press the Source Search button on the projector, remote control, or Control Pad, or tap the Source

Select icon on the whiteboard. Select the USB1 source.

141

The PC Free screen appears.

2. Do the following as necessary to locate your files:

• If you need to display files inside a subfolder on your device, press the arrow buttons to highlight

the folder and press the Enter button.

• To move back up a folder level on your device, highlight Back to Top and press Enter.

• To view additional files in a folder, highlight Next page or Previous page and press Enter.

3. To display the first page of a PDF file at full size, press the arrow buttons to highlight the file and

press Enter. (Press the Esc button to return to the file list screen.)

Note: If any file names are longer than 8 characters or include unsupported symbols, the file names

may be shortened or changed only in the screen display. If a PDF file extension is not .pdf, the file

does not appear in the file list.

4. While projecting a PDF file, use the following commands to control the display as necessary:

• To move to the next or previous page, press the up or down arrow button.

142

• To display a menu of pages to select from, press the Esc button. Then press the left or right arrow

button to select a page and press Enter.

• To enlarge the view of a page to fit the screen, press Enter. Press Enter again to return to

standard size display.

• To rotate a displayed page, press the left or right arrow button.

5. To stop the display, press the Esc button, press the up or down arrow button to highlight EXIT, and

press Enter.

Parent topic: Projecting a PC Free Presentation

Slideshow Display Options

You can select these display options when using the projector's Slideshow feature.

Setting Options Description

Display Order Name Order Displays files in name order

Date Order Displays files in date order

Sort Order In Ascending Sorts files in first-to-last order

In Descending Sorts files in last-to-first order

Continuous Play On Displays a slide show continuously

Off Displays a slide show one time through

143

Setting Options Description

Screen Switching

Time

No Does not display the next file automatically

1 Second to 60 Seconds Displays files for the selected time and

switches to the next file automatically; high

resolution images may switch at a slightly

slower rate

Effect Wipe Transitions between images with a wipe effect

Dissolve Transitions between images with a dissolve

effect

Random Transitions between images using a random

variety of effects

Parent topic: Projecting a PC Free Presentation

144

Adjusting Projector Features

Follow the instructions in these sections to use your projector's feature adjustments.

Shutting Off the Picture and Sound Temporarily

Stopping Video Action Temporarily

Zooming Into and Out of Images

Scheduling Projector Events

Projector Security Features

Creating a User Pattern to Display

Shutting Off the Picture and Sound Temporarily

You can temporarily turn off the projected picture and sound if you want to redirect your audience's

attention during a presentation. Any sound or video action continues to run, however, so you cannot

resume projection at the point that you stopped it.

If you want to display an image such as a company logo or picture when the presentation is stopped, you

can set up this feature using the projector's menus.

1. Press the A/V Mute button on the remote control to temporarily stop projection and mute any sound.

2. To turn the picture and sound back on, press A/V Mute again.

Parent topic: Adjusting Projector Features

145

Stopping Video Action Temporarily

You can temporarily stop the action in a video or computer presentation and keep the current image on

the screen. Any sound or video action continues to run, however, so you cannot resume projection at the

point that you stopped it.

Note: You can also stop video action using the interactive pens.

1. Press the Freeze button on the remote control to stop the video action.

2. To restart the video action in progress, press Freeze again.

Parent topic: Adjusting Projector Features

Zooming Into and Out of Images

You can draw attention to parts of a presentation by zooming into a portion of the image and enlarging it

on the screen.

Note: You can also zoom into your image using the interactive pens.

146

1. Press the E-Zoom + button on the remote control.

You see a crosshair on the screen indicating the center of the zoom area.

2. Use the following buttons on the remote control to adjust the zoomed image:

• Use the arrow buttons to position the crosshair in the image area you want to zoom into.

• Press the E-Zoom + button repeatedly to zoom into the image area, enlarging it as necessary.

Press and hold the E-Zoom + button to zoom in more quickly.

• To pan around the zoomed image area, use the arrow buttons.

• To zoom out of the image, press the E-Zoom – button as necessary.

• To return to the original image size, press Esc.

Parent topic: Adjusting Projector Features

Scheduling Projector Events

You can save a projector command, such as turning the projector on or off or switching input sources, as

an "event". You can schedule when you want the projector to automatically execute the command.

Note: The Time/Schedule Protection setting in the Password Protection menu must be turned off to

schedule an event.

Saving a Scheduled Event

Viewing Scheduled Events

Editing Scheduled Events

Parent topic: Adjusting Projector Features

147

Related tasks

Setting a Password

Saving a Scheduled Event

You can select projector commands you want to perform and schedule them as an event.

1. Press the Menu button.

2. Select the Extended menu and press Enter.

3. Select the Time/Schedule Settings setting and press Enter.

The Schedule Settings screen appears.

4. Select the Schedule menu and press Enter.

5. Select Add New and press Enter.

6. In the Event Settings section, select the events you want to have occur. (Select No Change for

events that you do not want to occur.)

7. In the Date/Time Settings section, set the date and time for the scheduled events to occur.

8. When you are finished, select Save and press Enter.

9. To schedule more events, repeat the previous 4 steps.

10. Select Setup complete and select Yes to save your changes.

Parent topic: Scheduling Projector Events

Related references

Projector Setup Settings - Extended Menu

Viewing Scheduled Events

You can view your scheduled events on the calendar displayed on the Schedule Settings screen.

1. Press the Menu button on the remote control or control panel.

2. Select the Extended menu.

3. Select Time/Schedule Settings.

148

4. Select Schedule.

The Schedule Settings screen is displayed.

Colored boxes on the calendar indicate the following:

One-time event

Repeating event

Communication is on or off

Event is invalid

5. To view an event, press the left and right arrow buttons on the remote to select a day.

The screen displays the details of the events scheduled for that day. A blue icon indicates an

enabled event; a gray icon indicates a disabled event, and the icon indicates a repeating

event.

Parent topic: Scheduling Projector Events

Related references

Projector Setup Settings - Extended Menu

Editing Scheduled Events

You can edit your scheduled events on the calendar displayed on the Schedule Settings screen.

1. Press the Menu button on the remote control or control panel.

2. Select the Extended menu.

149

3. Select Time/Schedule Settings.

4. Select Schedule.

The Schedule Settings screen is displayed.

Colored boxes on the calendar indicate the following:

One-time event

Repeating event

Communication is on or off

Event is invalid

5. To edit an event, press the up and down arrow buttons on the remote to highlight an event.

Note: While an event is selected, pressing the button will enable or disable the event.

6. Press the Esc button and choose an option..

•On/Off: Enables or disables the event

•Edit: Edits the settings for the event

•Clear: Deletes the event

7. Select Edit and change the settings for the event.

8. Select Save.

You see the new event on the Schedule screen.

Parent topic: Scheduling Projector Events

150

Related references

Projector Setup Settings - Extended Menu

Projector Security Features

You can secure your projector to deter theft or prevent unintended use by setting up the following

security features:

• Password security to prevent the projector from being turned on, and prevent changes to the startup

screen and other settings.

• Button lock security to block operation of the projector using the buttons on the control panel.

• Security cabling to physically cable the projector in place.

Password Security Types

Locking the Projector's Buttons

Installing a Security Cable

Parent topic: Adjusting Projector Features

Password Security Types

You can set up these types of password security using one shared password:

•Power On Protection password prevents anyone from using the projector without first entering a

password.

•User's Logo Protection password prevents anyone from changing the custom screen the projector

can display when it turns on or when you use the A/V Mute feature. The presence of the custom

screen discourages theft by identifying the projector’s owner.

•Network Protection password prevents anyone from changing the network settings in the projector

menus.

•Time/Schedule Protection password prevents anyone from changing the projector's time or

schedule settings.

Setting a Password

Selecting Password Security Types

Entering a Password to Use the Projector

Saving a User's Logo Image to Display

Parent topic: Projector Security Features

151

Setting a Password

To use password security, you must set a password.

1. Hold down the Freeze button on the remote control for about ten seconds or until you see this menu.

2. Press the down arrow to select Password and press Enter.

You see the prompt "Change the password?".

3. Select Yes and press Enter.

4. Press and hold down the Num button on the remote control and use the numeric buttons to set a

four-digit password.

The password displays as **** as you enter it. Then you see the confirmation prompt.

5. Enter the password again.

You see the message "Password accepted."

6. Press Esc to return to the menu.

152

7. Make a note of the password and keep it in a safe place in case you forget it.

Parent topic: Password Security Types

Selecting Password Security Types

After setting a password, you see this menu, allowing you to select the password security types you want

to use.

If you do not see this menu, hold down the Freeze button on the remote control for five seconds until the

menu appears.

1. To prevent unauthorized use of the projector, select Power On Protection, press Enter, select On,

press Enter again, and press Esc.

2. To prevent changes to the User's Logo screen or related display settings, select User's Logo

Protection, press Enter, select On, press Enter again, and press Esc.

3. To prevent changes to network settings, select Network Protection, press Enter, select On, press

Enter again, and press Esc.

4. To prevent changes to the projector's time or schedule settings, select Time/Schedule Protection,

press Enter, select On, press Enter again, and press Esc.

You can attach the Password Protect sticker to the projector as an additional theft deterrent.

Note: Be sure to keep the remote control in a safe place; if you lose it, you will not be able to enter the

password required to use the projector.

Parent topic: Password Security Types

Related references

Projector Feature Settings - Settings Menu

153

Projector Network Settings - Network Menu

Related tasks

Turning On the Projector

Saving a User's Logo Image to Display

Related topics

Scheduling Projector Events

Entering a Password to Use the Projector

If a password is set up and a Power On Protection password is enabled, you see a prompt to enter a

password whenever you turn on the projector.

You must enter the correct password to use the projector.

1. Press and hold down the Num button on the remote control while you enter the password using the

numeric buttons.

154

The password screen closes.

2. If the password is incorrect, the following may happen:

• You see a "wrong password" message and a prompt to try again. Enter the correct password to

proceed.

• If you enter an incorrect password several times in succession, the projector displays a request

code and a message to contact Epson Support. When you contact Epson Support, provide the

displayed request code and proof of ownership for assistance in unlocking the projector.

Parent topic: Password Security Types

Related tasks

Selecting Password Security Types

Saving a User's Logo Image to Display

You can transfer an image to the projector and then display it whenever the projector turns on. You can

also display the image when the projector is not receiving an input signal or when you temporarily stop

projection (using the A/V Mute feature). This transferred image is called the User's Logo screen.

The image you select as the User's Logo can be a photo, graphic, or company logo, which is useful in

identifying the projector's owner to help deter theft. You can prevent changes to the User's Logo by

setting up password protection for it.

1. Display the image you want to project as the User's Logo.

2. Press the Menu button, select the Extended menu, and press Enter.

155

3. Select the User's Logo setting and press Enter.

You see a prompt asking if you want to use the displayed image as a user's logo.

4. Select Yes and press Enter.

You see a selection box overlaying your image.

5. Use the arrow buttons on the remote control to surround the image area you want to use as the

User's Logo and press Enter.

You see a prompt asking if you want to select this image area.

6. Select Yes and press Enter. (If you want to change the selected area, select No, press Enter, and

repeat the last step.)

You see the User's Logo zoom factor menu.

7. Select a zoom percentage and press Enter.

You see a prompt asking if you want to save the image as the User's Logo.

8. Select Yes and press Enter.

Note: It takes a few moments for the projector to save the image; do not use the projector, its remote

control, or any connected equipment until it is finished.

You see a completion message.

9. Press Esc to exit the message screen.

10. Select the Extended menu and press Enter.

11. Select Display and press Enter.

156

12. Select when you want to display the User's Logo screen:

• To display it whenever there is no input signal, select Display Background and set it to Logo.

• To display it whenever you turn the projector on, select Startup Screen and set it to On.

• To display it whenever you press the A/V Mute button, select A/V Mute and set it to Logo.

To prevent anyone from changing the User's Logo settings without first entering a password, set a

password and enable User's Logo security.

Parent topic: Password Security Types

Related tasks

Setting a Password

Locking the Projector's Buttons

You can lock the buttons on the projector's control panel to prevent anyone from using the projector. You

can lock all the buttons or all the buttons except the power button.

1. Press the Menu button.

2. Select the Settings menu and press Enter.

3. Select the Control Panel Lock setting and press Enter.

4. Select one of these lock types and press Enter:

• To lock all of the projector's buttons, select Full Lock.

157

• To lock all buttons except the power button, select Partial Lock.

You see a confirmation prompt.

5. Select Yes and press Enter.

Unlocking the Projector's Buttons

Parent topic: Projector Security Features

Unlocking the Projector's Buttons

If the projector's buttons have been locked, hold the Enter button on the projector's control panel for

seven seconds to unlock them.

Parent topic: Locking the Projector's Buttons

Installing a Security Cable

You can install two types of security cables on the projector to deter theft.

• Use the security slot on the projector to attach a Kensington Microsaver Security system, available

from Epson.

• Use the security cable attachment point on the projector to attach a wire cable and secure it to a room

fixture or heavy furniture.

Note: Do not pass drop-prevention cables through the security cable attachment point when mounting

the projector on a wall or ceiling.

Parent topic: Projector Security Features

158

Creating a User Pattern to Display

You can transfer an image to the projector and then display it as a pattern to aid in presentations when

you use the Pattern Display feature. This transferred image is called the User Pattern.

1. Display the image you want to project as the User Pattern from a connected computer or video

source.

2. Press the Menu button, select the Settings menu, and press Enter.

3. Select the Pattern setting and press Enter.

4. Select the User Pattern setting and press Enter.

You see a prompt asking if you want to use the displayed image as a User Pattern.

5. Select Yes and press Enter.

Note: It takes a few moments for the projector to save the image; do not use the projector, its remote

control, or any connected equipment until it is finished.

You see a completion message.

6. Press Esc to exit the message screen.

Parent topic: Adjusting Projector Features

159

Using the Interactive Features

Follow the instructions in these sections to use your projector's interactive features.

Interactive Modes

Using the Interactive Pens

Using Finger Touch Interactivity

Using BrightLink With a Computer

Whiteboard Mode

Annotation Mode (PC Free)

Splitting the Screen

Interactive Modes

The BrightLink interactive features turn any wall into an interactive whiteboard, either with or without a

computer. These interactive modes are available:

• In whiteboard mode, you can use one or both interactive pens or your finger (BrightLink Pro 1430Wi)

to write on the projected "whiteboard". You can split the screen and interact with the whiteboard and

another source. You can insert images from a thumbdrive or scanner and save, print, or email your

"pages," without connecting a computer.

• In annotation mode (PC Free Annotation), you can annotate over content projected from a computer,

tablet, document camera, or other source. You can capture your annotated pages, then save or print

them. You can even split the screen and annotate on two images at the same time, using one or both

pens.

• In PC Interactive mode, you can use the interactive pen or your finger (BrightLink Pro 1430Wi) as a

mouse to navigate, select, and scroll through content from your computer. You can split the screen

and interact with two projected images at the same time.

Note: You can also use the Easy Interactive Tools software to provide additional interactive features,

such as saving your annotations and printing them. See the online Easy Interactive Tools Operation

Guide for detailed instructions.

Parent topic: Using the Interactive Features

Related concepts

Whiteboard Mode

Using BrightLink With a Computer

160

Annotation Mode (PC Free)

Using the Interactive Pens

The BrightLink interactive pens turn any wall into an interactive whiteboard, either with or without a

computer.

• With a computer, you can use Easy Interactive Tools. This software lets you use the pen as a mouse

to annotate, save, and interact with content from your computer. Two people can annotate at the same

time.

• Without a computer, you can use the built-in toolbar. This lets you annotate images from a document

camera, iPad, DVD player, or other source.

Follow the instructions in these sections to use the interactive pens.

Using the Pens

Pen Calibration

Parent topic: Using the Interactive Features

Related concepts

Easy Interactive Tools

Related tasks

Selecting a Networked Device Source

Using the Pens

Your projector came with a blue pen and an orange pen, identified by the color on the end of the pen.

You can use either pen, or both pens at the same time (one of each color), with Easy Interactive Tools.

Make sure the pen batteries are installed.

161

Note: The pen turns off automatically after 20 minutes of inactivity. Tap the pen tip or press the button on

the side to turn the pen back on.

1 Pen tip

2 Battery light

3 Power/function button

4 Attachment for optional strap or cord

5 Battery cover

• To turn on the pen, tap the pen tip or press the power/function button.

Note: If you press the button, the battery light flashes briefly, then turns off. If the battery is low, the

battery light flashes continuously.

162

• For best performance, hold the pen perpendicular to the board, as shown below. Do not cover the

black section near the tip of the pen.

• To write or draw on the projection surface in annotation mode or whiteboard mode, do the following:

• To select a projected item, such as an icon, tap the projection surface with the pen tip.

• To draw on the projected screen, tap the projection surface with the pen and drag it as necessary.

• To move the pointer, hover over the surface without touching it.

• To switch the pen from drawing tool to eraser, press the power/function button on the side.

163

• To use the pen as a mouse in PC Interactive mode, do the following:

• To left-click, tap the board with the pen tip.

• To double-click, tap twice.

• To right-click, press the power/function button on the side.

• To click and drag, tap and drag with the pen.

• To move the cursor, hover over the board without touching it.

Note: If you do not want to use the hovering feature, you can turn it off using the Easy Interactive

Function setting in the projector's Extended menu.

Parent topic: Using the Interactive Pens

Related concepts

Whiteboard Mode

Using BrightLink With a Computer

Annotation Mode (PC Free)

Pen Calibration

Calibration coordinates the position of the pen with the location of your cursor. You only need to calibrate

the first time you use your projector's interactive features. Calibration results remain until you calibrate

again.

Be sure to calibrate the pen before performing finger touch calibration (BrightLink Pro 1430Wi).

If you notice positioning discrepancies after doing any of the following, calibrate again:

• Performing Keystone correction

• Adjusting the image size

164

• Using the Image Shift feature

• Moving the projector

Note: Move any pen you are not using away from the projection screen while calibrating.

Calibrating Automatically

Calibrating Manually

Parent topic: Using the Interactive Pens

Related tasks

Correcting Image Shape with the Keystone Buttons

Resizing the Image with the Wide and Tele Buttons

Adjusting the Image Position

Calibrating Automatically

You do not need the pens or a computer for Auto Calibration.

Note: You can start Auto Calibration by pressing the User button on the remote control or by pressing

the Menu button on the remote control as described here.

1. Press the Menu button, select the Extended menu, and press Enter.

165

2. Select the Easy Interactive Function setting and press Enter.

3. Select Auto Calibration and press Enter.

4. Adjust the image focus, if necessary.

5. Press Enter to select Yes.

A pattern appears then disappears, and the system is calibrated. If you see a message that

calibration failed, you need to calibrate manually.

166

The cursor location and pen position should match after calibration. If not, you may need to calibrate

manually.

Parent topic: Pen Calibration

Calibrating Manually

If the cursor location and pen position do not match after auto calibration, you can calibrate manually.

1. Press the Menu button, select the Extended menu, and press Enter.

2. Select the Easy Interactive Function setting and press Enter.

167

3. Select Manual Calibration and press Enter.

4. Adjust the image focus, if necessary.

5. Press Enter to select Yes.

A flashing green circle appears in the upper left corner of your projected image.

6. Touch the center of the circle with the tip of the pen.

The circle disappears, and you see another circle below the first one.

168

Note: For the most accurate calibration, make sure you touch the center of the circle.

7. Touch the center of the next circle, then repeat. When you get to the bottom of the column, the next

circle appears at the top of a new column.

Note: Make sure you are not blocking the signal between the pen and the interactive receiver (next

to the projection window on the projector).

If you make a mistake, press the Esc button on the remote control to go back to the previous circle.

To restart the calibration process, press and hold the Esc button for 2 seconds.

8. Continue until all of the circles disappear.

Parent topic: Pen Calibration

169

Using Finger Touch Interactivity

You can use your finger to perform the same functions as the interactive pens when you install the

Touch Unit (BrightLink Pro 1430Wi).

Note: See the Installation Guide for detailed instructions on installing the Touch Unit.

Touch Unit Safety Instructions

Calibrating for Finger Touch Interactivity

Using Finger Touch Operations

Parent topic: Using the Interactive Features

Related concepts

Whiteboard Mode

Using BrightLink With a Computer

Annotation Mode (PC Free)

Related tasks

Adjusting the Angle of the Touch Unit

Touch Unit Safety Instructions

The Touch Unit enables finger touch interactivity with your projector (BrightLink Pro 1430Wi). Do not

connect it to any other projectors or devices.

A built-in, high-power laser is emitted from the laser diffusion ports on the back of the Touch Unit.

170

Follow these precautions when using the Touch Unit and finger touch interactivity:

• Children using finger touch interactivity should always be accompanied by an adult.

• Never disassemble or modify the Touch Unit.

• Do not look into the laser diffusion ports on the back of the Touch Unit. The laser can damage your

eyes. Extra care should be taken when children are present.

• Do not allow the laser light from the Touch Unit to pass through or be reflected by any optical devices,

such as a magnifying glass or mirror. This could cause personal injury or fire.

• Do not view the laser light from the Touch Unit using an optical device such as an eye loupe,

magnifying glass, or microscope, especially within 2.75 inches (70 mm) of the laser diffusion ports.

This could damage your eyes.

• Unplug the projector from the electrical outlet and refer all repairs to qualified service personnel if any

problems occur with the Touch Unit.

The Touch Unit is a Class 1 laser product that complies with IEC/EN60825-1:2007. The labels indicating

the Class 1 laser product and warnings are located in the following areas on the Touch Unit:

171

Parent topic: Using Finger Touch Interactivity

Calibrating for Finger Touch Interactivity

Finger touch calibration coordinates the positioning of your finger with the location of the cursor

(BrightLink Pro 1430Wi).

Note: Make sure you have calibrated the pens before calibrating for finger touch interactivity.

1. Press the Menu button, select the Extended menu, and press Enter.

172

2. Select the Easy Interactive Function setting and press Enter.

3. Select Touch Unit Setup and press Enter.

4. Select Touch Calibration and press Enter.

173

The following screen appears:

5. Adjust the image focus, if necessary.

6. Press Enter to select Yes.

A flashing green circle appears in the upper left corner of your projected image.

7. Touch and hold the center of the circle with your finger until the circle disappears and another circle

appears, then release it.

The circle disappears, and you see another circle below the first one.

174

Note: For the most accurate calibration, make sure you touch the center of the circle with the tip of

your finger.

Note: Make sure you are not blocking the signal between your finger and the interactive receiver

(next to the projection window on the projector).

8. Touch the center of the next circle with your finger and continue until all of the circles disappear.

When you get to the bottom of a column, the next circle appears at the top of a new column.

Note: If you make a mistake, press the Esc button on the remote control to go back to the previous

circle. To restart the calibration process, press and hold the Esc button for 2 seconds.

9. If the cursor location and your finger position do not match, repeat these steps to calibrate again.

175

Parent topic: Using Finger Touch Interactivity

Related tasks

Adjusting the Angle of the Touch Unit

Using Finger Touch Operations

You can use your finger to interact with the projected screen, just as you would use an interactive pen

(BrightLink Pro 1430Wi). You can use either a pen or your finger, or use both at the same time.

When performing touch operations with your finger, you can use two fingers in annotation and

whiteboard modes.

1. Calibrate the pens.

2. Install the Touch Unit as described in your mount's Installation Guide.

3. Adjust the angle of the Touch Unit if it was not adjusted during installation.

4. Calibrate for finger touch interactivity.

5. Turn on your projector. This automatically turns on the Touch Unit also.

The blue light on the Touch Unit remains lit.

176

6. To write or draw on the projection surface in annotation mode or whiteboard mode, do the following:

• To select a projected item, such as an icon, tap the projection surface with your finger.

• To draw on the projected screen, tap the projection surface with your finger and drag it as

necessary.

7. To use your finger as a mouse in PC Interactive mode, do the following:

• To left-click, tap the board with your finger.

• To double-click, tap twice with your finger.

• To right-click, press the board with your finger for about 3 seconds.

• To click and drag, press on and drag an item with your finger.

• To scroll, drag your finger on the screen.

8. If your operating system supports these functions, you can also do the following:

• To zoom in or out, touch an item using two fingers and either move your fingers away from each

other (zoom in) or toward each other (zoom out).

• To rotate an image, touch the image with your fingers and rotate your hand.

177

• To drag up or down on a page, or move backward or forward in a browser window, use swiping

gestures or flicks.

Note: Finger touch operations may not work correctly with long or artificial nails, or fingers wearing

bandages. If your fingers are too close together or crossed, or your sleeve touches the screen, finger

touch may not be recognized. Some operating systems may not support gestures.

Parent topic: Using Finger Touch Interactivity

Related tasks

Calibrating for Finger Touch Interactivity

Using BrightLink With a Computer

You can connect a computer to the projector and install the software from the CD labeled "Epson

Projector Software for Easy Interactive Function." You can then do the following:

• Use the pens or your finger (BrightLink Pro 1430Wi) as a mouse to control your computer

• Use the Easy Interactive Tools software to annotate with both pens or a combination of pen and finger

touch (BrightLink Pro 1430Wi) at the same time

Note: See the online Easy Interactive Tools Operation Guide for detailed information.

• Save and print your annotations

• Use the Tablet PC input panel in Windows 8.x, Windows 7, or Windows Vista

• Use Ink Tools for annotation in Microsoft Office applications

PC Interactive Mode System Requirements

Switching to PC Interactive Mode

Controlling Computer Features from a Projected Screen (PC Interactive Mode)

Adjusting the Pen Operation Area

Easy Interactive Tools

Windows Pen Input and Ink Tools

Parent topic: Using the Interactive Features

PC Interactive Mode System Requirements

Your computer system must meet the system requirements here to use PC Interactive mode and Easy

Interactive Tools.

178

Note: Easy Interactive Driver must be installed and running to use Easy Interactive Tools on a Mac.

Requirement Windows Mac

Operating system Windows XP Professional SP2 or later,

Home Edition

OS X 10.5.x, 10.6.x, OS X 10.7.x,

10.8.x, 10.9.x (32-bit)

OS X 10.6.x, OS X 10.7.x, 10.8.x,

10.9.x (64-bit)

Windows Vista Ultimate, Enterprise,

Business, Home Premium, and Home

Basic (32-bit)

Windows 8.x Pro, Enterprise, Windows 7

Ultimate, Enterprise, Professional, Home

Premium, and Home Basic (32- and 64-

bit)

CPU Intel Pentium M 1.6 GHz or faster (Core2

Duo 1.2 GHz or faster recommended)

Power PC G4 1.5 GHz or faster

(Core Duo 1.83 GHz or faster

recommended)

Memory 512MB or more (1G or more recommended)

Hard disk space 100MB or more

Display Resolution between 1024 × 768 and 1920 × 1200, 16-bit color or greater

Parent topic: Using BrightLink With a Computer

Related concepts

Easy Interactive Tools

Switching to PC Interactive Mode

You can easily switch between PC Free annotation and PC interactive modes. Although you can use

both pens in PC interactive mode, this may cause interference in some applications that only support

one pen. To avoid interference, turn off the unused pen or move it away from the projection surface.

• To switch to PC interactive mode, select the Pen mode icon on the toolbar, then select the

Mouse icon.

• To switch back to annotation mode, select the Mouse icon, then select the Pen mode icon.

Parent topic: Using BrightLink With a Computer

179

Controlling Computer Features from a Projected Screen (PC Interactive Mode)

You can navigate, select, and interact with your computer programs from the projected screen using the

interactive pens or your finger (BrightLink Pro 1430Wi) just as you would a mouse.

Note: OS X users need to install the Easy Interactive Driver before using PC Interactive mode. Go to

epson.com/support (U.S.) or epson.ca/support (Canada) and select your projector.

1. Connect the projector to your computer using a USB cable.

2. Turn on your projector and project your computer screen.

3. Press the Menu button on the remote control, select the Extended menu, and press the Enter

button.

4. Select the USB Type B setting and press the Enter button.

5. Select one of the following:

•Easy Interactive Function to use PC Interactive mode.

•USB Display/Easy Interactive Function to use PC Interactive mode and USB Display.

•Wireless Mouse/USB Display to use the mouse and USB Display

6. Press the Esc button to exit the USB Type B menu.

180

7. Select the Easy Interactive Function setting and press the Enter button.

8. Select one of the following as the Pen Operation Mode depending on your projector model and

computer operating system (BrightLink Pro 1430Wi):

BrightLink Pro 1420Wi:

•Two Users/Mouse: Lets you use both interactive pens as a mouse

•One User/Mouse: Lets you use one interactive pen as a mouse

•One User/Pen: Uses the Windows pen and ink feature (Windows 8.x, Windows 7, and Windows

Vista)

BrightLink Pro 1430Wi:

•Mode 1: Windows XP or earlier

•Mode 2: Windows Vista, Windows 7, Windows 8.x, and OS X

•Mode 3: Linux

9. Press the Enter button on the remote control and press the Menu button to exit the Extended menu.

10. Hover near or tap on the board or the projected image with the interactive pen or your finger

(BrightLink Pro 1430Wi).

The icon is displayed on the projected screen.

181

11. Select the icon, then select the icon.

You can now operate the computer using the interactive pens or your finger (BrightLink Pro 1430Wi).

Parent topic: Using BrightLink With a Computer

Adjusting the Pen Operation Area

If you connect a different computer or adjust the computer's resolution, the pen operation area is

adjusted automatically to match your mouse pointer position. If you intend to only use a single computer

with the projector, set Auto Adjust Pen Area to Off. If you will be using many computers with the

projector, set Auto Adjust Pen Area to On.If you notice that the pen position is incorrect when using PC

Interactive mode, you can adjust the pen area manually.

Note: Manual adjustment is not available when projecting from a LAN source.

1. Project your computer's desktop.

2. Press the Menu button, select the Extended menu, and press Enter.

182

3. Select the Easy Interactive Function setting and press Enter.

4. Select Advanced in the PC Interactive section and press Enter.

5. Select Manual Adj. Pen Area and press Enter.

183

You see this screen:

6. Press Enter to select Yes.

The mouse pointer moves toward the top left corner.

7. When the mouse pointer stops at the top left corner of the image, touch the tip of the pointer with the

interactive pen.

The mouse pointer moves toward the bottom right corner.

8. When the mouse pointer stops at the bottom right corner of the image, touch the tip of the pointer

with the interactive pen.

Parent topic: Using BrightLink With a Computer

Easy Interactive Tools

Your projector came with a CD containing the Easy Interactive Tools software for use with a computer.

Easy Interactive Tools lets you use your interactive pen or finger (BrightLink Pro 1430Wi) as a mouse to

navigate, select, scroll, draw, save, and interact with projected content from your computer.

These two modes are available:

• Annotation (interactive) mode displays the toolbar on the projected image and lets you use the pen or

finger (BrightLink Pro 1430Wi) as a mouse to open applications, access links, and operate scroll bars,

for example (using one pen at a time). You can also annotate whatever is displayed from your

computer (using both pens at the same time).

• Whiteboard mode lets you project on one of 3 solid colors or 6 background patterns, and use the

toolbar to write or draw on the background. You can also import images from your computer or a

document camera. In full screen whiteboard mode, two people can use the pens at the same time.

Finger touch is also available in whiteboard mode. (BrightLink Pro 1430Wi)

Note: For detailed instructions on using the Easy Interactive Tools software, see the online Easy

Interactive Tools Operation Guide or the online help.

184

Parent topic: Using BrightLink With a Computer

Windows Pen Input and Ink Tools

If you are using Windows 8.x, Windows 7, or Windows Vista, you can use the pen input and Ink tools to

add input and annotations to your work. You can also use these features over a network when you set

the interactive features to be available on your network. See the EasyMP Network Projection Operation

Guide for instructions on setting up your computer for network projection.

Enabling Windows Pen Input and Ink Tools

Using Windows Pen Input and Ink Tools

Parent topic: Using BrightLink With a Computer

Enabling Windows Pen Input and Ink Tools

To use the pen input and Ink tools in Windows 8.x, Windows 7, or Windows Vista, you need to adjust the

pen operation mode in your projector's menus.

1. Press the Menu button, select the Extended menu, and press Enter.

185

2. Select the Easy Interactive Function setting and press Enter.

3. Select Pen Operation Mode and press Enter.

4. Select one of the following:

•One User/Pen (BrightLink Pro 1420Wi)

•Mode 1 or Mode 2 when using Ink tools (BrightLink Pro 1430Wi); this also lets you use Windows

multi-touch features

186

•Mode 2 when using pen input (BrightLink Pro 1430Wi)

Parent topic: Windows Pen Input and Ink Tools

Using Windows Pen Input and Ink Tools

If you are using Windows 8.x, Windows 7, or Windows Vista, you can add handwritten input to your work

and convert it to text.

If you have Microsoft Office 2003 or later, you can also use the Ink function to add handwritten notes to a

Word document, Excel spreadsheet, or PowerPoint presentation.

Note: Option names for the annotation functions may vary depending on your version of Microsoft

Office.

• To open the Touch Keyboard in Windows 8.x, right-click or tap-and-hold on the Taskbar, and select

Toolbars > Touch Keyboard. Select the keyboard icon on the screen and select the pen icon.

• To open the Tablet PC input panel in Windows 7 or Windows Vista, select > All Programs >

Accessories > Tablet PC > Tablet PC Input Panel.

You can write in the box using the interactive pen or your finger (BrightLink Pro 1430Wi), and select

from a variety of options to edit and convert the text.

• To add Ink annotations in Microsoft Office applications, select the Review menu, and select Start

Inking.

Note: In Microsoft Word or Excel, select the Insert tab and select Start Inking.

187

• To annotate your PowerPoint slides in Slideshow mode, press the button on the side of the interactive

pen or press the projection surface with your finger (BrightLink Pro 1430Wi) for about 3 seconds, and

select Pointer Options > Pen from the pop-up menu.

Note: This also works in Windows XP Tablet PC Edition.

For more information about these features, see Windows Help.

Parent topic: Windows Pen Input and Ink Tools

Whiteboard Mode

You can use the pens or your finger (BrightLink Pro 1430Wi) to write or draw on the projection surface

just as you would on a chalkboard or dry erase board.

You can also do the following:

• Insert images from a thumbdrive or scanner and resize, rotate, or crop the images

• Insert a background pattern or template, or a variety of shapes

• Save, print, or email your whiteboard pages

Using the Whiteboard Toolbars

The Main Whiteboard Toolbar

Selecting Background Templates

Zooming Images in Whiteboard Mode

Inserting and Working With Images

Using the Shapes Tool

Selecting Line Width and Color

The Bottom Whiteboard Toolbar

Selecting Whiteboard Settings

Inserting a Document or Image From a Scanner

Selecting a Networked Device Source

Saving Pages in Whiteboard Mode

Working With Thumbnail Pages

Printing in Whiteboard Mode

Emailing Your Whiteboard Pages

Sharing the Whiteboard

Parent topic: Using the Interactive Features

188

Using the Whiteboard Toolbars

You can use both pens at the same time in whiteboard mode.

1. Press the Whiteboard button on the remote control or control pad.

You see the whiteboard screen, with the main toolbar and the bottom toolbar:

2. To move the main toolbar to the other side of the screen, select the arrow.

Note: You can use the pen or your finger (BrightLink Pro 1430Wi) to move the arrow up or down.

3. To add a new page, select the New page icon on the bottom toolbar.

Your current page appears as a thumbnail image on the bottom toolbar.

4. To close the main toolbar, select the icon at the bottom of the toolbar.

Note: If you want to hide the toolbar automatically after drawing, select the icon at the bottom of

the toolbar.

5. To show or hide the bottom toolbar, select one of the arrows.

189

Parent topic: Whiteboard Mode

The Main Whiteboard Toolbar

The main whiteboard toolbar lets you draw, write, and insert images and backgrounds. The toolbar also

lets you easily switch to PC Free annotation or computer interactive mode.

Switch to PC Free annotation mode

Switch to whiteboard mode

Undo the last annotation

190

Redo the last undo

Select all objects in a rectangular area

Select all objects in a freehand area

Turn the pen into a draggable pointer

Capture the selected area as an image

Insert a .jpg or .webp image from a thumbdrive or network folder

Insert a circle, square, triangle, or other shape

Change custom pen color and width

Write or draw free-form lines with custom pen

Change highlighter pen color and width

Write or draw free-form lines with transparent highlighter pen

Black pen (fine point on left, thick on right)

Red pen (fine point on left, thick on right)

191

Blue pen (fine point on left, thick on right)

Eraser (thin width on left, thick on right)

Clear all content on page

Displays the current color and mode for both interactive pens and finger (BrightLink Pro

1430Wi)

Hide the toolbar after each annotation

Close the toolbar

Parent topic: Whiteboard Mode

Related tasks

Inserting and Working With Images

Using the Shapes Tool

Selecting Line Width and Color

Selecting Background Templates

In whiteboard mode, you can insert horizontal lines, a graph-paper grid, or another background template

and place it on your whiteboard pages. You can select from 10 pre-installed patterns or add up to 5

custom templates by accessing the projector through your web browser.

1. In whiteboard mode, select the Template tool on the bottom toolbar.

You see the available templates.

2. Select one of the template patterns.

3. If you want to use the pattern for all the pages in the current session, select Apply to all pages.

4. To scale the pattern, select the pattern repeatedly to cycle through the different scales.

Note: Not all patterns will scale.

Parent topic: Whiteboard Mode

192

Related references

The Bottom Whiteboard Toolbar

Related tasks

Adding Templates from a Web Browser

Zooming Images in Whiteboard Mode

You can use the pen to zoom in and pan around your enlarged image, then zoom out when you are

done.

1. Select the Zoom tool on the bottom toolbar.

2. Do one of the following to adjust the image if necessary:

• Select the plus icon to enlarge the image.

• Select the minus icon to shrink the image.

• Select the x1 icon to return to the original size.

• Press and drag on the screen to pan around the enlarged area.

Parent topic: Whiteboard Mode

Related references

The Bottom Whiteboard Toolbar

Inserting and Working With Images

In whiteboard mode, you can use the Insert Image tool to insert an image from a thumbdrive or a

network folder. Images can be in .webp or .jpg format, with a maximum size of 2048 × 2048 pixels. Once

the image is projected, you can move, resize, rotate, or crop it.

Note: You can also use the tool on the bottom toolbar to import files (including pdf files) in

whiteboard mode.

1. Select the Insert Image tool.

2. Select the image you want to add, then select Insert Image.

After a moment, the image appears on the whiteboard page.

193

3. Once you have selected the image, select either the Rectangle Select or Free Select tool and

do any of the following as necessary:

• To move the image, touch inside it and drag with the pen.

• To resize the image, touch any corner and drag inward to shrink or outward to enlarge.

• To rotate the image, touch the round icon at the top of the image and drag left or right.

• To crop the image, select and drag the side of the image.

4. The menu in the bottom right corner of the image allows you to:

•Cut: removes the image from the whiteboard. Tap a location on the screen to paste the image

again.

•Copy: touch a location on the screen and paste a copy of the image

•Paste: create a new selected copy of the image. Drag the image to the desired location.

•Auto Crop: removes any black borders around the selected image

•Delete: removes the image from the whiteboard

After you have edited the image, select another tool from the whiteboard toolbar to exit image edit

mode.

Parent topic: Whiteboard Mode

Related references

The Main Whiteboard Toolbar

Using the Shapes Tool

You can add a variety of shapes to your projected image and select the color and line width.

1. Select the Shapes tool.

2. Select the line width, color, and shape you want to create, or select the Line tool to define your

own shape.

3. Drag the pen on the projection surface to draw the shape you want.

Parent topic: Whiteboard Mode

Related references

The Main Whiteboard Toolbar

194

Selecting Line Width and Color

You can select the color and line width for both the custom Pen and the Highlighter tools.

1. Select the icon next to the custom Pen or Highlighter annotation tool.

2. Select the line width and color you want to use for the Pen or Highlighter tools.

3. Use the pen to write or draw on the projection surface.

Parent topic: Whiteboard Mode

Related references

The Main Whiteboard Toolbar

The Bottom Whiteboard Toolbar

The bottom whiteboard toolbar lets you add scanned or imported images, and view, save, print, or email

your pages.

Share the current whiteboard session

Start a new meeting or whiteboard session

Open a .jpg, .webp, or .pdf file from a thumbdrive or network folder. When you open a multi-

page pdf, each page in the document appears on a separate whiteboard page.

Scan and insert an image

Select a background template

Duplicate the current page

195

Delete the current page

Open a new page. The current page appears as a thumbnail on the bottom toolbar.

Display the previous page thumbnail

Display the next page thumbnail

Print one or more pages

Save a page or a series of pages on a thumbdrive or network folder

Email a page or series of pages

Select an input source

Zoom into the whiteboard

Stops projection and mutes audio. Touch the screen again to restore the image and sound.

Split the screen and project two images. When the screen is split, select the tool again to

return to a single image.

196

Display a help screen for the toolbar functions

Show or hide bottom toolbar

Parent topic: Whiteboard Mode

Related tasks

Selecting Background Templates

Zooming Images in Whiteboard Mode

Selecting a Networked Device Source

Saving Pages in Whiteboard Mode

Working With Thumbnail Pages

Printing in Whiteboard Mode

Emailing Your Whiteboard Pages

Starting a Shared Whiteboard Session

Connecting to a Shared Whiteboard from a Projector

Inserting a Document or Image From a Scanner

Related topics

Sharing the Whiteboard

Selecting Whiteboard Settings

Follow the instructions in these sections to select settings for capturing, scanning, saving, printing, and

emailing in whiteboard mode.

Selecting Basic Whiteboard Settings and Policies

Selecting Whiteboard Print Settings

Selecting Settings for Saving Whiteboard Pages

Selecting Settings for Emailing Whiteboard Pages

Parent topic: Whiteboard Mode

Selecting Basic Whiteboard Settings and Policies

You can select the whiteboard features you want to use and control the way whiteboard pages are saved

in the projector.

197

1. Press the Menu button on the remote control.

2. Select the Extended menu and press Enter.

3. Select Whiteboard Settings and press Enter.

4. Select Basic and press Enter.

198

5. Select the following basic options as necessary:

•Administrator Password lets you enter a password up to 16 alphanumeric characters long for

controlling whiteboard settings. This password is also used for network settings.

•Clock Display Settings lets you control the date and time display on the bottom whiteboard

toolbar.

•Keyboard Layout lets you select the onscreen keyboard layout.

•Delete All Internal Data lets you delete data stored in the projector. Use this option if you have

problems with internal storage, or you need to dispose of the projector or have it repaired.

Note: Use the displayed keyboard to enter the password. Press the arrow buttons on the remote

control to highlight characters and press Enter to select them.

6. Select the Policy menu and press Enter.

7. Select the following policy options as necessary:

•Policy Setting options let you disable capturing, printing, scanning, USB storage, network

storage, or emailing from the projector. All features are enabled by default.

•Template Settings lets you control how the user templates can be changed. When Protect User

Templates is set to On, the user templates can only be changed through the web browser

interface. When set to Off, the user templates can be edited in whiteboard mode.

•Internal Storage settings let you control the use of the projector's internal storage. In most cases,

you should leave this setting On, and select Retain for saved data. The Backup Time for Saved

199

Data setting determines how often whiteboard pages are backed up automatically in case of a

power outage.

8. When you finish selecting settings, select Setup Complete and follow the on-screen instructions to

save your settings and exit the menus.

Parent topic: Selecting Whiteboard Settings

Related references

Projector Setup Settings - Extended Menu

Related tasks

Printing in Whiteboard Mode

Emailing Your Whiteboard Pages

Saving Pages in Whiteboard Mode

Selecting Background Templates

Adding Templates from a Web Browser

Selecting Whiteboard Print Settings

You can select the default settings for printing whiteboard pages from the projector.

1. Press the Menu button on the remote control.

2. Select the Extended menu and press Enter.

3. Select Whiteboard Settings and press Enter.

200

4. Select Print and press Enter.

5. Select the following printing options as necessary:

•Default Printer lets you select either USB or Network for the printer connection. You can change

this setting when you print in whiteboard mode, but not in annotation mode.

Note: Selecting USB will also enable scanning from Epson All-in-One printers.

•Paper Size lets you select either Letter or A4 as the default paper size.

•Network Printer Settings let you enter the print job user name and IP address for a printer

connected to the same network as the projector. Once this is set, you can select Get printer

information to have the projector communicate with the printer and automatically determine the

printer type. You can also select the Printer Type manually.

•Test Print lets you send a test page to the connected printer.

Note: Use the displayed keyboard to enter the IP address if necessary. Press the arrow buttons on

the remote control to highlight numbers and press Enter to select them.

6. When you finish selecting settings, select Setup Complete and follow the on-screen instructions to

save your settings and exit the menus.

Parent topic: Selecting Whiteboard Settings

201

Related references

Projector Setup Settings - Extended Menu

Supported Printer Types

Related tasks

Connecting a Printer to the Control Pad

Selecting Settings for Saving Whiteboard Pages

You can select the default settings for saving whiteboard pages from the projector.

1. Press the Menu button on the remote control.

2. Select the Extended menu and press Enter.

3. Select Whiteboard Settings and press Enter.

202

4. Select Save and press Enter.

5. Select the following options for saving as necessary:

•Default Save Location lets you select either USB or Network for saving on a USB thumb drive or

network folder. You can change this setting when you save in whiteboard mode, but not in

annotation mode.

•UNC Address (Universal Naming Convention) lets you set a folder and path in the following

format: \\host name\share name. You can use an IP address or a NetBIOS name as the host

name. You can enter up to 63 alphanumeric characters for the address.

When an IP address is set as the host name, the projector communicates with the file sharing

server using the CIFS protocol. If a routing configuration is used for the TCP protocol, the subnet

is skipped and communication is performed outside the subnet.

When a NetBIOS name is set as the host name, the projector communicates with the file sharing

server using the SMB protocol.

Note: The folder must be on a shared network drive. To save to a folder on a different network

segment, use the WINS server setting on the wired or wireless network menu.

203

•User name lets you set the a user name with read/write privileges on the network folder. You can

enter up to 64 alphanumeric characters. You can enter a domain name by adding it before the

user name and separating them with a backslash (domain\username).

•Password lets you enter a password for the user name. You can enter up to 64 alphanumeric

characters. After you enter the password and select Setup complete, the password is hidden.

•Check Connection lets you test the network connection.

Note: Use the displayed keyboard to enter the address, user name, and password if necessary.

Press the arrow buttons on the remote control to highlight numbers and press Enter to select them.

6. When you finish selecting settings, select Setup Complete and follow the on-screen instructions to

save your settings and exit the menus.

Parent topic: Selecting Whiteboard Settings

Selecting Settings for Emailing Whiteboard Pages

You can select the settings for emailing whiteboard pages from the projector.

1. Press the Menu button on the remote control.

2. Select the Extended menu and press Enter.

3. Select Whiteboard Settings and press Enter.

204

4. Select Mail and press Enter.

5. Select the following options for emailing as necessary:

•SMTP Server let you enter the IP address or host name for the mail server. You can enter up to

63 alphanumeric characters. If you specify a host name, you must configure a DNS server.

Note: You cannot use the following IP addresses: 127.x.x.x, 192.0.2.x, or 224.0.0.0 to

255.255.255.255.

•Authentication lets you set the type of authentication expected by the mail server

•Port Number lets you enter a port number for the SMTP server. The default port is 25.

•User name lets you enter a user name for the mail server. You can enter up to 64 alphanumeric

characters.

•Password lets you enter a password for the mail server. You can enter up to 64 alphanumeric

characters.

•From lets you enter the email address to be displayed to the sender. You can enter up to 64

alphanumeric characters.

•Default e-mail address lets you enter an optional address for testing. You can enter up to 64

alphanumeric characters.

205

•Send a test e-mail connects to the SMTP server and sends a test email to the address you set as

the default.

Note: Use the displayed keyboard to enter the addresses. Press the arrow buttons on the remote

control to highlight numbers or characters and press Enter to select them. You cannot use spaces in

the User Name and Password fields. You can not use spaces or the following symbols: " * + , : ; < =

> ? [ ] | in the Reply to and From fields.

6. When you finish selecting settings, select Setup Complete and follow the on-screen instructions to

save your settings and exit the menus.

Parent topic: Selecting Whiteboard Settings

Related references

Projector Setup Settings - Extended Menu

Related tasks

Selecting Wired Network Settings

Selecting Wireless Network Settings Manually

Inserting a Document or Image From a Scanner

You can scan a paper document into a new page in whiteboard mode. Make sure a supported Epson all-

in-one printer is connected to the control pad (or to your network).

Note: Standalone scanners are not supported.

1. Place your document on the scanner glass or in the automatic document feeder (if available).

Note: You can place up to 10 sheets in the ADF. If you want to scan a longer document, scan the

pages in batches of 10.

2. Select the Scan tool on the bottom toolbar.

206

You see the Scan screen:

3. Select the following settings:

• Select Color or Monochrome

• Select the orientation for the scanned document.

• Under ADF, select On if you placed your document in the automatic document feeder.

4. Select Advanced to access additional options.

5. Select Scan on the Scan screen.

After a moment, you see your document or image on the screen.

Note: Multi-page documents appear on multiple whiteboard pages.

Parent topic: Whiteboard Mode

Related references

The Bottom Whiteboard Toolbar

Selecting a Networked Device Source

You can project an image from up to 50 devices connected to the projector via a network. You can select

the image source from computers running EasyMP Multi PC Projection, and smartphones or tablets

running Epson iProjection.

207

1. Select the Source Select icon on the projector control toolbar.

An image source list appears.

2. Select Participant List.

You see a list of available devices. The icon next to a user name indicates the currently selected

source.

208

3. Select the user name for the device from which you want to project.

Note: Select Refresh to update the user list.

4. Select Return.

You see the screen image from the selected device.

Parent topic: Whiteboard Mode

Related references

The Bottom Whiteboard Toolbar

Saving Pages in Whiteboard Mode

You can save your pages as .webp, .ewf, or .pdf files and select the location (network folder or

thumbdrive) where you want to store your files.

1. Press the Save button on the control pad or remote control, or select the Save tool on the

bottom toolbar.

2. Select the location where you want to save your file, then select OK.

You see a screen like the following:

3. To enter a file name, select the File Name text box.

The on-screen keyboard appears.

4. Use the keyboard to enter a file name, then select OK.

209

5. Select the location where you want to save the file by selecting the Location field. Choose either a

USB or Network location and navigate to the target folder, then select OK.

6. If sharing the whiteboard, select Distribute to all participants to temporarily save the file and make

it available for download through a web browser. After the file is downloaded, it is erased.

7. Select the format for saving. If you choose PDF or EWF (Epson Whiteboard Format), you can

encrypt the file and add a password. If you choose EWF, you can reopen the file later and continue

editing.

8. Select one of the following under Range:

•All to save all the pages in the current whiteboard session (available for PDF or EWF format only)

•Current to save only the current whiteboard page

•Selection if you want to save a range of pages. Tap the numbers in the boxes to select the range

of pages (available for PDF or EWF format only).

9. When you are ready, select Save.

Parent topic: Whiteboard Mode

Related references

The Bottom Whiteboard Toolbar

Working With Thumbnail Pages

Thumbnail pages are displayed on the bottom toolbar in whiteboard mode. You can scroll through your

pages with the pen or your finger (BrightLink Pro 1430Wi), select a page to display at full size, and copy

or delete individual pages. The 5 rectangles in the center of the bottom toolbar shown here are thumbnail

pages:

1. To display a page at full size, select its thumbnail.

2. To scroll through the thumbnail pages, select to move to the previous page or to move to

the next page.

210

3. Do any of the following as necessary:

• To add a new page, select the New page icon. A blank page opens, and this page appears

as the current thumbnail on the bottom toolbar.

• To duplicate the current page, select the icon. The duplicate page appears after the last

page displayed.

• To delete the current page, select the Delete icon.

• To change the order of the pages, select and hold a thumbnail for three seconds, then drag the

thumbnail to the new location.

Parent topic: Whiteboard Mode

Related references

The Bottom Whiteboard Toolbar

Printing in Whiteboard Mode

You can print your pages directly from the projector to a supported printer (USB or networked). You can

also select settings for your printed pages, including page numbers, time and date, and collation of

multiple copies.

Make sure your printer meets the control command requirements for printing from the projector.

1. Press the Print button on the control pad or remote control, or select the Print tool on the

bottom toolbar.

2. Select the number of copies and whether you want to print in color or black only (monochrome).

3. Select one of the following under Range:

•All to print all the pages in the current whiteboard session

•Current to print only the current whiteboard page

•Selection if you want to print selected pages. Tap the numbers in the boxes to select the range of

pages.

4. To make additional settings, select Advanced.

211

You see a screen like the following:

5. Select any of the following settings:

•Printer to choose between a USB and Network printer connection

•Paper Size to choose the size paper loaded in the printer (Letter or A4)

•Pages per sheet to print multiple reduced pages on one sheet of paper

•Page Border to add a border around each page

•Page Number to print the page number on each page

•Date & Time to print the time and date stamp on each page

•Collate to collate pages when printing multiple copies

•Duplex Printing to print on both sides of the paper

6. When you are ready, select Print.

212

Your page or pages are printed.

Parent topic: Whiteboard Mode

Related references

The Bottom Whiteboard Toolbar

Emailing Your Whiteboard Pages

If your projector is set up on your network, you can email your pages directly from the projector.

Note: Mail server settings must be configured before you can email from the projector. Use the

Whiteboard Settings function on the projector's Extended menu to configure email options.

1. Select the Email tool on the bottom toolbar.

You see a screen like the following:

2. To enter the email address for the recipient, tap the E-mail Address text box.

The on-screen keyboard appears.

3. Use the keyboard to enter the email address and select OK.

4. Select the plus icon to add another email address. You can send email to 10 addresses.

Note: If you imported an address book, you can select the address book icon to add up to 10

addresses.

213

5. Use the on-screen keyboard to enter the subject that you want to appear on the Subject line.

6. Use the on-screen keyboard to enter a file name for the attachment.

7. Select the file format for emailing. If you choose PDF or EWF (Epson Whiteboard Format), you can

encrypt the file and add a password.

8. Select any of the following under Range:

•All to send all the pages in the current whiteboard session (available for PDF or EWF format only)

•Current to send only the current whiteboard page

•Selection if you want to send a range of pages (available for PDF or EWF format only). Tap the

numbers in the boxes to select the range of pages.

9. When you are ready, select Send.

Your page or pages are sent.

Parent topic: Whiteboard Mode

Related references

The Bottom Whiteboard Toolbar

Related tasks

Selecting Settings for Emailing Whiteboard Pages

Creating an Address Book

Sharing the Whiteboard

Follow the instructions in these sections to share the whiteboard screen with other projectors, devices,

and computers.

Starting a Shared Whiteboard Session

Connecting to a Shared Whiteboard from a Computer or Other Device

Supported Web Browsers for Sharing a Whiteboard

Web Browser Toolbars

Connecting to a Shared Whiteboard from a Projector

Parent topic: Whiteboard Mode

Related references

The Bottom Whiteboard Toolbar

214

Starting a Shared Whiteboard Session

You can share the whiteboard with up to 15 devices on the same network SSID, including other

projectors that support whiteboard sharing, computers, and other devices.

Note: In order to share the whiteboard, the projector must be set up on a network, and your network

administrator must have opened TCP port 80. If using SSL, also open port 443.

1. Press the Whiteboard button on the remote control or control pad, or select the whiteboard icon

on the toolbar.

The projector displays the whiteboard.

2. Select the share icon on the bottom toolbar.

A dialog is displayed.

3. Select Start sharing with this whiteboard.

You see a dialog displaying the PIN code.

215

4. When connecting to the shared whiteboard, users must enter the PIN code. If you want to set your

own PIN code, select the PIN code field and enter a new 7-digit code.

Note: After you share the whiteboard, you cannot change the PIN code unless you restart the

whiteboard sharing session.

5. Select the Start button.

6. To set editing permissions for connected users, select the share icon on the bottom toolbar again.

You see the Shared Whiteboard dialog.

7. Select one of the following as the Share Configuration setting to permit access to features by

devices connecting to the whiteboard:

•Presentation: Connected devices can view and save the whiteboard screen.

•Discussion: Connected devices can draw on the shared screen.

•Collaboration: Connected devices can access all available features except creating a new

meeting.

Note: The projector displays connection information about the shared whiteboard under Network

information.

216

8. Select Stop sharing this whiteboard to end the whiteboard sharing session.

9. Select Close.

Parent topic: Sharing the Whiteboard

Related references

The Bottom Whiteboard Toolbar

Related tasks

Selecting Wireless Network Settings Manually

Selecting Wired Network Settings

Connecting to a Shared Whiteboard from a Computer or Other Device

You can connect to a shared whiteboard from a computer or device on the same network using a web

browser. You can view, save, and draw on the shared whiteboard from your connected computer or

device.

Note: Select the share icon on the bottom toolbar of the whiteboard to display the IP address and PIN

code for the shared whiteboard.

1. On the computer or other device, enter the whiteboard IP address into a web browser in this format:

<projector_ip_address>/wb.

You see a prompt to enter a PIN code.

2. Enter the PIN code and select Connect.

You see the shared whiteboard content and toolbar on your computer or device.

Parent topic: Sharing the Whiteboard

Supported Web Browsers for Sharing a Whiteboard

You can connect to a shared whiteboard using the web browsers described here.

Operating

system

Browser version Screen resolution of connected device or

computer

Windows Internet Explorer 8/9/10/11* Smaller than XGA

OS X Safari 5/6/7 Up to 1280 × 800

iOS iOS 6.0 or later Up to 1024 × 768

217

Operating

system

Browser version Screen resolution of connected device or

computer

Android Android OS 4.0 or later standard

browser

Up to 1024 × 768 (4:3 aspect ratio)

Up to 1280 × 600 (16:9 aspect ratio)

Up to 1280 × 720 (16:10 aspect ratio)

* Internet Explorer 8 and 9 require an SSL connection

Parent topic: Sharing the Whiteboard

Web Browser Toolbars

When connected through a web browser, the whiteboard toolbars allow you to interact with the shared

whiteboard. The available tools depend on the Share Configuration setting you selected.

Tool icon Description

Saves the whiteboard screen as a PDF or PNG file depending on the whiteboard

settings; available only when you select Distribute to the participants when saving to

the connected projector

Displays the pointer on the whiteboard screen and all connected devices

Adjusts the view of the display in the web browser window

Displays the entire whiteboard

Selects a pen for drawing

218

Tool icon Description

Selects a translucent highlighter pen for drawing

Selects a shape to place on the screen

Selects the eraser tool so you can click on content and select OK to delete it; you

cannot delete partially drawn content

Selects an object or image

Selects the line thickness for the current pen or shape

Selects the color of the selected pen or shape

Loads an image on the whiteboard and resizes it if it is larger than the whiteboard*

Selects a background for the whiteboard page

Control which whiteboard page is displayed on the shared whiteboard

On: Synchronizes the page with the connected whiteboard. When you edit the page,

the change is reflected on the shared whiteboard.

Off: Displays a page that differs from the connected whiteboard. You can only modify

pages that are displayed on the shared whiteboard.

Displays the page number of the edited pages and arrows for moving between them

219

Tool icon Description

Creates a new whiteboard page

* Images must be JPG or PNG, with a resolution up to 2048 × 2048.

Parent topic: Sharing the Whiteboard

Connecting to a Shared Whiteboard from a Projector

You can connect another projector on the same network to a projector that is sharing its whiteboard.

1. Press the Whiteboard button on the remote control or control pad, or select the whiteboard icon

on the toolbar.

The projector displays the whiteboard.

2. Press the share icon on the bottom toolbar.

The projector displays the Shared Whiteboard dialog.

3. Select Connect to the shared whiteboard.

The projector displays the Shared Whiteboard dialog.

220

4. Enter the IP address and PIN code for the projector you want to connect to.

Note: To display the addresses for the last five projector connections, select the arrow icon next to

the address field.

5. Press the Connect button.

Both projectors display the shared whiteboard screen.

To disconnect from the shared whiteboard, select the share icon on the bottom toolbar and select

Disconnect.

Parent topic: Sharing the Whiteboard

Related references

The Bottom Whiteboard Toolbar

Annotation Mode (PC Free)

Annotation mode lets you project from a computer, tablet, video device, or other source and add notes to

your projected content. You can easily switch between sources and capture, save, or print the images

with annotations. You can also split the screen to annotate on two images at the same time.

Drawing on a Projected Image (Annotation Mode)

Using the Annotation Toolbars

The Main Annotation Toolbar

Zooming Images in Annotation Mode

The Bottom Annotation Toolbar

Printing in Annotation Mode

Saving Images in Annotation Mode

Parent topic: Using the Interactive Features

Drawing on a Projected Image (Annotation Mode)

You can project from a computer, tablet, video device, or other source and add notes to your projected

content using the interactive pens or your finger (BrightLink Pro 1430Wi). You can use one pen, both

pens at the same time, or a combination of pens and finger touch (BrightLink Pro 1430Wi).

1. Project an image from a connected device.

2. Hover near or tap the board or projected image with the interactive pen or your finger (BrightLink Pro

1430Wi). Tap the annotation icon on the toolbar.

221

You see the main toolbar on the side and the projection control toolbar on the bottom of the

projected image.

3. To move the main toolbar to the other side of the screen, tap the arrow on the opposite side of

the screen.

Note: You can use the pen or your finger (BrightLink Pro 1430Wi) to move the arrow icon up or

down to reposition the toolbar.

4. To switch to one of the other interactive modes, do one of the following:

• To switch to whiteboard mode, select the Whiteboard tool.

• To switch to PC Interactive mode, select , then select .

Note: You can also press the Pen Mode button on the remote control to switch between modes.

5. To close the main toolbar, select the icon at the bottom of the toolbar.

Note: If you want to hide the toolbar automatically after drawing, select the icon at the bottom of

the toolbar.

222

6. To show or hide the projection control toolbar, select the arrow.

Parent topic: Annotation Mode (PC Free)

Related references

The Main Annotation Toolbar

The Bottom Annotation Toolbar

Related tasks

Inserting a Document or Image From a Scanner

Inserting and Working With Images

Using the Annotation Toolbars

You can use both pens at the same time in annotation mode.

1. Project an image from a connected device.

2. Turn on one of the pens and hover near or tap the projected image.

You see the main toolbar and the bottom toolbar on the projected image, for example:

223

3. To move the main toolbar to the other side of the screen, select the arrow.

Note: You can use the pen to move the arrow icon up or down.

4. To switch to one of the other modes, do one of the following:

• To switch to whiteboard mode, select the Whiteboard tool.

• To switch to computer interactive mode, select , then select .

5. To close the main toolbar, select the icon at the bottom of the toolbar.

Note: If you want to hide the toolbar automatically after drawing, select the icon at the bottom of

the toolbar.

6. To show or hide the bottom toolbar, select the arrow.

Parent topic: Annotation Mode (PC Free)

Related concepts

Whiteboard Mode

Using BrightLink With a Computer

Annotation Mode (PC Free)

224

The Main Annotation Toolbar

The main annotation toolbar lets you draw and write on your projected image. The toolbar also lets you

easily switch to whiteboard or computer interactive mode.

Switch to annotation mode (PC free annotation)

Switch to whiteboard mode

Undo the last annotation

225

Redo the last undo

Change custom pen color and width

Write or draw free-form lines with custom pen

Change highlighter pen color

Write or draw free-form lines with transparent highlighter pen

Black pen (fine point on left, thick on right)

Red pen (fine point on left, thick on right)

Blue pen (fine point on left, thick on right)

Eraser (thin width on left, thick on right)

Clear all annotations

Hide the toolbar after each annotation

Close the toolbar

Switch modes. Select then to switch to computer interactive mode (PC

interactive). Select then to switch back to annotation mode (PC free annotation).

Parent topic: Annotation Mode (PC Free)

226

Zooming Images in Annotation Mode

You can use the pen to zoom in on a portion of your image, the same as you can using the E-Zoom

button on the remote control.

1. Select the Zoom tool.

2. Do one of the following to adjust the image if necessary:

• Press and drag on the screen to pan around the enlarged area.

• Select the plus icon to enlarge the image.

• Select the minus icon to shrink the image.

• Select the x1 icon to return to the original size.

Parent topic: Annotation Mode (PC Free)

The Bottom Annotation Toolbar

The bottom annotation toolbar lets you split the screen and capture, print, or save your images.

Capture the projected image. Switch to whiteboard mode to paste the image onto a new

page.

Print the projected image

Save the projected image in .webp format

Select an input source

Zoom into the whiteboard

227

Stops projection and mutes audio. Touch the screen again to restore the image and sound.

Pauses video.

Split the screen and project two images. When the screen is split, select the tool again to

return to a single image.

Show or hide bottom toolbar

Parent topic: Annotation Mode (PC Free)

Related tasks

Printing in Annotation Mode

Saving Images in Annotation Mode

Printing in Annotation Mode

You can print the projected image directly from the projector to a supported printer (USB or networked).

Make sure your printer meets the control command requirements for printing from the projector.

1. Press the Print button on the control pad or remote control, or select the Print tool on the

bottom annotation toolbar.

2. Select the number of copies you want.

3. When you are ready, select Print.

Your page is printed on the default printer set up in the Print menu under the Whiteboard Settings

menu.

Parent topic: Annotation Mode (PC Free)

Related tasks

Selecting Whiteboard Print Settings

228

Saving Images in Annotation Mode

You can save your images as .webp files in the default location set in the projector's menu system.

1. Press the Save button on the control pad or remote control, or select the Save tool on the

bottom annotation toolbar.

You see a confirmation message.

2. Select Yes.

Your image is named and saved automatically.

Parent topic: Annotation Mode (PC Free)

Related tasks

Selecting Settings for Saving Whiteboard Pages

Splitting the Screen

You can split the screen and project from two sources at the same time. You can annotate and interact

with both sources.

1. Press the Split button on the remote control or select the Split tool on the bottom toolbar.

The current image is reduced and appears on the left side of the projection surface.

2. Press the Source Select icon on the bottom toolbar.

229

You see a screen like this:

3. Select the two sources you want to display. Not all combinations of sources are valid.

If you want to write on a blank screen, select any unused source. Unused sources display the color

selected in the Display Background setting. The Logo option will display a blue background.

Note: You can also press the Menu button on the remote control and select the Source option to

select the two sources.

4. Press the Switch Source button to display the two sources.

5. Do any of the following as necessary:

• To change to a different source at any time, press the Menu button on the remote control and

select Source, or press the Select Source icon on the bottom toolbar.

• To annotate on the right screen, press the Menu button on the remote control, select Target Pen

Mode, and select Screen Right. Set the Pen Mode setting to PC Free Annotation.

230

• To use PC interactive mode on the right screen, press the Menu button on the remote control,

select Target Pen Mode, and select Screen Right. Set the Pen Mode setting to PC Interactive.

Note: If you select Video,USB1, or USB2 as a source, you cannot use PC interactive mode.

• To reverse the left and right images, press the Menu button on the remote control and select

Swap Screens.

• To make one image larger, press the Menu button on the remote control, select Screen Size, and

select Larger Left or Larger Right.

6. To return to displaying one image, press the Esc button on the remote control, or press the Split

Screen icon on the bottom toolbar.

Note: The following operations cannot be performed during split screen projection:

• Menu settings

• E-Zoom

• Switching aspect mode

• Operations made by the User button on the remote control

• Auto Iris

• Light Optimizer

• Image Processing

• Freeze (if one screen is displaying the whiteboard)

Parent topic: Using the Interactive Features

231

Adjusting the Menu Settings

Follow the instructions in these sections to access the projector menu system and change projector

settings.

Using the Projector's Menus

Image Quality Settings - Image Menu

Input Signal Settings - Signal Menu

Projector Feature Settings - Settings Menu

Projector Setup Settings - Extended Menu

Projector Network Settings - Network Menu

Projector Setup Settings - ECO Menu

Projector Information Display - Info Menu

Projector Reset Options - Reset Menu

Using the Projector's Menus

You can use the projector's menus to adjust the settings that control how your projector works. The

projector displays the menus on the screen.

232

1. Press the Menu button on the control panel or remote control.

You see the menu screen displaying the Image menu settings.

233

2. Press the up or down arrow buttons to move through the menus listed on the left. The settings for

each menu are displayed on the right.

Note: The available settings depend on the current input source.

3. To change settings in the displayed menu, press Enter.

4. Press the up or down arrow button to move through the settings.

5. Change the settings using the buttons listed on the bottom of the menu screens.

6. To return all the menu settings to their default values, select Reset.

7. When you finish changing settings on a menu, press Esc.

8. Press Menu or Esc to exit the menus.

Parent topic: Adjusting the Menu Settings

Related references

Image Quality Settings - Image Menu

Input Signal Settings - Signal Menu

Projector Feature Settings - Settings Menu

Projector Setup Settings - Extended Menu

Projector Network Settings - Network Menu

Projector Setup Settings - ECO Menu

Projector Information Display - Info Menu

Projector Reset Options - Reset Menu

234

Image Quality Settings - Image Menu

Settings on the Image menu let you adjust the quality of your image for the input source you are currently

using. The available settings depend on the currently selected input source.

To change settings for an input source, make sure the source is connected and select that source.

Setting Options Description

Color Mode See the list of available Color

Modes

Adjusts the vividness of image

colors for various image types

and environments

Brightness Varying levels available Lightens or darkens the overall

image

Contrast Varying levels available Adjusts the difference between

light and dark areas of the image

Color Saturation Varying levels available Adjusts the intensity of the image

colors

Tint Varying levels available Adjusts the balance of green to

magenta tones in the image

Sharpness Varying levels available Adjusts the sharpness or

softness of image details

235

Setting Options Description

Color Temp. (color temperature) High

Medium

Low

Sets the overall color tone; High

tints the image blue and Low

tints the image red

Advanced Various options available Adjusts the gamma levels and

intensity of individual hues in the

image

Auto Iris Off

Normal

High Speed

Adjusts the projected luminance

based on the image brightness

when certain Color Modes are

selected; High Speed sets faster

luminance correction for fast-

moving images

Note: The Brightness setting does not affect lamp brightness. To change the lamp brightness mode,

use the Power Consumption setting.

Parent topic: Adjusting the Menu Settings

Related references

Available Color Modes

Related tasks

Turning On Auto Iris

Changing the Color Mode

236

Input Signal Settings - Signal Menu

Normally the projector detects and optimizes the input signal settings automatically. If you need to

customize the settings, you can use the Signal menu. The available settings depend on the currently

selected input source.

Note: You can restore the default settings of the Position,Tracking, and Sync settings by pressing the

Auto button on the remote control.

To change settings for an input source, make sure the source is connected and select that source.

Setting Options Description

Auto Setup On

Off

Automatically optimizes computer

image quality (when On)

Resolution Auto

Wide

Normal

Sets the input signal resolution if

not detected automatically using

the Auto option

Tracking Varying levels available Adjusts signal to eliminate vertical

stripes in computer images

237

Setting Options Description

Sync. Varying levels available Adjusts signal to eliminate

fuzziness or flickering in

computer images

Position Up, down, left, right Adjusts the image location on the

screen

Progressive Off

Video

Film/Auto

Sets whether to convert

interlaced-to-progressive signals

for certain video image types

Off: for fast-moving video images

Video: for most video images

Film/Auto: for movies, computer

graphics, and animation

Noise Reduction Off

NR1

NR2

Reduces flickering in analog

images in two levels

HDMI Video Range Auto

Normal

Expanded

Sets the video range to match the

setting of the device connected to

the HDMI input port

Auto: detects the video range

automatically

Normal: normally for images from

a device other than a computer;

can also be selected if the black

areas of the image are too bright

Expanded: normally for images

from a computer; can also be

selected if the image is too dark

238

Setting Options Description

Input Signal Auto

RGB

Component

Specifies the signal type from

input sources connected to

computer ports

Auto: detects signals

automatically

RGB: corrects color for

computer/RGB video inputs

Component: corrects color for

component video inputs

Video Signal Auto

Various video standards

Specifies the signal type from the

input sources connected to the

video ports

Auto: detects signals

automatically

Aspect See the list of available aspect

ratios

Sets the aspect ratio (width-to-

height ratio) for the selected input

source

Overscan Auto

Off

Changes the projected image

ratio to make the edges visible by

a selectable percentage or

automatically

Image Processing Fine

Fast

Adjusts image processing

speed/quality

Parent topic: Adjusting the Menu Settings

Related concepts

Image Aspect Ratio

Related references

Available Image Aspect Ratios

Related tasks

Changing the Image Aspect Ratio

239

Projector Feature Settings - Settings Menu

Options on the Settings menu let you customize various projector features.

Setting Options Description

Keystone H/V Keystone

Quick Corner

Adjusts image shape to

rectangular (horizontally and

vertically)

H/V Keystone: lets you manually

correct horizontal and vertical

sides

Quick Corner: select to correct

image shape and alignment

using an on-screen display

Split Screen – Turns split screen on or off

Zoom Varying levels available Adjusts the size of the projected

image

Image Shift Varying positions available Adjusts the position of the

projected image

240

Setting Options Description

Control Panel Lock Full Lock

Partial Lock

Off

Controls projector button locking

to secure the projector

Full Lock: locks all buttons

Partial Lock: locks all buttons

except the power button

Off: no buttons locked

Pointer Shape Three shapes available Changes the shape of the remote

control pointer feature

Volume Varying levels available Adjusts the volume of projector’s

speaker system or external

speakers

Remote Receiver Front/Rear

Front

Rear

Off

Limits reception of remote control

signals by the selected receiver;

Off turns off all receivers

User Button Power Consumption

Info

Progressive

Closed Caption

Test Pattern

Resolution

Pattern Display

Auto Calibration

Assigns a menu option to the

User button on the remote

control for one-touch access

241

Setting Options Description

Pattern Pattern Display

Pattern Type

User Pattern

Test Pattern

Selects various pattern display

options

Pattern Display: lets you display

the selected pattern type on the

screen to aid in presentation

Pattern Type: selects the type of

grid or line pattern to display

User Pattern: captures a

projected screen and saves it as

a pattern for display

Test Pattern: displays a test

pattern to assist in focusing and

zooming the image and

correcting image shape

Parent topic: Adjusting the Menu Settings

Related tasks

Correcting Image Shape with the Keystone Buttons

Correcting Image Shape with Quick Corner

Adjusting the Image Position

Locking the Projector's Buttons

Unlocking the Projector's Buttons

242

Projector Setup Settings - Extended Menu

Settings on the Extended menu let you customize various projector setup features that control its

operation.

Easy Interactive Function Settings

Setting Options Description

General Easy Interactive Function settings

Auto Calibration

Manual Calibration

— Start calibration for the

interactive pens

243

Setting Options Description

Touch Unit Setup

(BrightLink Pro 1430Wi)

Installation Pattern

Power

Angle Adjustment

Touch Calibration

Select settings for the Touch Unit

Installation Pattern: displays

reference points to help you

determine the installation position

of the Touch Unit

Power: turns on the Touch Unit

power

Angle Adjustment: performs

angle adjustment for laser

diffusion

Touch Calibration: performs

calibration for finger touch

operations

Pen Mode PC Free Annotation

PC Interactive

Selects the mode for the

interactive pens

PC Free Annotation: draws on

the projected screen without

software or PC required

PC Interactive: operates a

mouse or interactive device from

the projected screen using the

interactive pen or your finger

(BrightLink Pro 1430Wi)

Hovering On

Off

Turns the pen hovering feature

on and off; when set to On, the

pointer follows the pen tip as you

hover it over the screen and

move it around

244

Setting Options Description

Advanced Distance of Projectors

Sync of Projectors

Wired Sync Mode

Pen Button Function

Confirm Clear Screen

Color Palette

Selects various settings for

interactive features

Distance of Projectors,Sync of

Projectors, and Wired Sync

Mode: let you adjust features for

using multiple projectors of the

same model in the same room

Pen Button Function: sets the

pen to act as an eraser

Confirm Clear Screen: lets you

display a confirmation screen

before clearing all of the content

Color Palette: lets you choose a

different palette if certain colors

are difficult to see

PC Interactive Easy Interactive Function settings

Pen Operation Mode

(BrightLink Pro 1420Wi)

Two Users/Mouse

One User/Mouse

One User/Pen

Sets the operation mode and

number of users for the

interactive pen

Two Users/Mouse or One

User/Mouse: lets you use the

interactive pen as a mouse

One User/Pen: lets you use the

Windows pen and ink features

Pen Operation Mode

(BrightLink Pro 1430Wi)

Mode 1

Mode 2

Mode 3

Selects the operating system

version for pen operations

Mode 1: Windows XP or earlier

Mode 2: OS X, or Windows Vista

or later

Mode 3 : Linux

245

Setting Options Description

Enable Right Click On

Off

Lets you use a long pen press or

finger press (BrightLink Pro

1430Wi) as a right-click operation

when using mouse mode

Advanced Pen Tip Button

Auto Adjust Pen Area

Manual Adj. Pen Area

Select pen operation and

adjustment options

Pen Tip Button: assign either

Right Click or Left Click to the

pen tip button

Select either Auto Adjust Pen

Area or Manual Adj. Pen Area

as the pen area adjustment

option

Other Extended Settings

Setting Options Description

Whiteboard Settings Basic

Policy

Save

Mail

Reset

Displays whiteboard setting

menus

246

Setting Options Description

Display Messages

Display Background

Startup Screen

A/V Mute

Toolbars

Pen Mode Icon

Projector Control

Selects various display options

Messages: controls whether

messages are displayed on the

screen

Display Background: selects

the screen color or logo to

display when no signal is

received

Startup Screen: controls

whether a special screen

appears when the projector starts

A/V Mute: selects the screen

color or logo to display when A/V

Mute is turned on

Toolbar Tab: controls whether

the tab is always displayed in

annotation mode

Pen Mode Icon: controls the

display and position of the pen

icon in interactive computer

mode

Projector Control: controls

where the projector control

toolbar is displayed on the screen

Closed Caption Off

CC1

CC2

Controls use of closed captions

and selects the closed caption

type

User's Logo – Creates a screen that the

projector displays to identify itself

and enhance security

247

Setting Options Description

Projection Front

Front/Upside Down

Rear

Rear Upside Down

Selects the way the projector

faces the screen so the image is

oriented correctly

Operation Direct Power On

High Altitude Mode

Startup Source Search

Auto Power On

Selects various operation options

Direct Power On: lets you turn

on the projector without pressing

the power button

High Altitude Mode: regulates

the projector’s operating

temperature at altitudes above

4921 feet (1500 m)

Startup Source Search:

automatically detects the image

signal that is input when the

projector is turned on

Auto Power On: lets you turn on

the projector by turning on a

computer connected to the

Computer port

248

Setting Options Description

A/V Settings A/V Output

Audio Output

HDMI1 Audio Output

HDMI2 Audio Output

Selects the following when the

projector is in standby mode

(turned off):

A/V Output: The Always On

setting lets the projector output

audio and video signals even

while it is standby mode.

Available only when Standby

Mode is set to Communication

Audio Output: Selects the audio

input port when projecting

images from the Computer,

Video, and USB-A ports.

HDMI1 Audio Output and

HDMI2 Audio Output: Selects

which Audio port provides audio

output when viewing images from

the HDMI 1/MHL and HDMI 2

ports on the projector.

249

Setting Options Description

USB Type B Easy Interactive Function

USB Display/Easy Interactive

Function

Wireless Mouse/USB Display

Selects what happens when you

connect your computer to the

projector's USB-B port

Easy Interactive Function: lets

you use the interactive pens or

your finger (BrightLink Pro

1430Wi) with your computer

USB Display/Easy Interactive

Function: lets you display your

computer's image through the

USB port and use the interactive

pens or your finger (BrightLink

Pro 1430Wi) with your computer

Wireless Mouse/USB Display:

lets you use the wireless mouse

feature and display your

computer's image through the

USB port (interactivity not

available)

Time/Schedule Settings Date & Time

Schedule

Schedule Reset

Setup Complete

Sets the projector's date and time

and scheduled projector actions

Language Various languages available Selects the language for

projector menu and message

displays (not changed by Reset

option)

Parent topic: Adjusting the Menu Settings

Related concepts

Projector Connections

Projection Modes

Related references

Projector Setup and Installation Options

250

Related tasks

Connecting to a Computer for Pen Use or USB Mouse Control

Turning On the Projector

Selecting the Language for the Projector Menus

Changing the Projection Mode Using the Menus

Saving a Scheduled Event

Viewing Scheduled Events

Editing Scheduled Events

Selecting Basic Whiteboard Settings and Policies

Selecting Whiteboard Print Settings

Selecting Settings for Saving Whiteboard Pages

Selecting Settings for Emailing Whiteboard Pages

Projector Network Settings - Network Menu

Settings on the Network menu let you view network information and set up the projector for monitoring

and control over a network.

251

Setting Options Description

Net. Info - Wireless LAN Connection mode

Wireless LAN Sys.

Antenna level

Projector Name

SSID

DHCP

IP Address

Subnet Mask

Gateway Address

MAC Address

Displays wireless network status

and details

Net. Info - Wired LAN Projector Name

DHCP

IP Address

Subnet Mask

Gateway Address

MAC Address

Displays wired network status

and details

Network Configuration Accesses additional network

menus

Configures your network settings

Parent topic: Adjusting the Menu Settings

Related references

Wireless LAN Menu Settings

Related tasks

Selecting Wired Network Settings

Selecting Wireless Network Settings Manually

252

Projector Setup Settings - ECO Menu

Settings on the ECO menu let you customize projector functions to save power. When you select a

power-saving setting, a leaf icon appears next to the menu item.

Setting Options Description

Power Consumption Auto

Normal

ECO

Selects the brightness mode of

the projector lamp

Auto: sets the projector to sense

the optimum lamp brightness and

adjust the lamp brightness

accordingly

Normal: sets maximum lamp

brightness

ECO: reduces lamp brightness

and fan noise, and saves power

and lamp life

Light Optimizer On

Off

When Power Consumption is

set to Normal, the lamp

brightness is adjusted based on

the projected image; you can set

this option for each color mode

253

Setting Options Description

Sleep Mode On

Off

Automatically places the

projector in standby mode after

an interval of inactivity

Sleep Mode Timer 1 to 30 minutes Sets the interval for Sleep Mode

A/V Mute Timer On

Off

Automatically turns off the

projector after 30 minutes if A/V

Mute is enabled

Standby Mode Communication On

Communication Off

Enable this setting to allow the

following operations to occur

when the projector is in standby

mode:

• Monitor and control the

projector over a network

• Output audio and video to an

external device (A/V Output

must be set to Always On)

ECO Display On

Off

Displays a leaf icon in the bottom

left corner of the projected screen

to indicate the power-saving

status when the lamp brightness

changes

Parent topic: Adjusting the Menu Settings

Related references

Projector Lamp Specifications

254

Projector Information Display - Info Menu

You can display information about the projector and input sources by viewing the Info menu. However,

you cannot change any settings in the menu.

Select Version to display the projector's firmware version. Select Projector Info to display the settings

described below.

Note: Available settings depend on the current input source. The lamp usage timer does not register any

hours until you have used the lamp for at least 10 hours.

Information item Description

Lamp Hours Displays the number of hours (H) the lamp has been used in

Normal and ECO Power Consumption modes; if the information is

displayed in yellow, obtain a genuine Epson replacement lamp

soon

Source Displays the name of the port to which the current input source is

connected

Input Signal Displays the input signal setting of the current input source

Resolution Displays the resolution of the current input source

Video Signal Displays the video signal format of the current input source

255

Information item Description

Refresh Rate Displays the refresh rate of the current input source

Sync Info Displays information that may be needed by a service technician

Status Displays information about projector problems that may be needed

by a service technician

Serial Number Displays the projector's serial number

Event ID Displays the Event ID number corresponding to a specific projector

problem; see the list of Event ID codes

Event ID Code List

Parent topic: Adjusting the Menu Settings

Event ID Code List

If the Event ID option on the Info menu displays a code number, check this list of Event ID codes for the

solution to the projector problem associated with the code.

Event ID code Cause and solution

0432 The EasyMP Network Projection program did not start. Turn the projector off and

then on again.

0435

0434 Unstable network communication. Check the network communication status, wait a

few moments, and try connecting to the network again.

0482

0484

0485

0433 Cannot display the transferred images. Restart the EasyMP Network Projection

program.

0481 Communication with computer was disconnected. Restart the EasyMP Network

Projection program.

0483 The EasyMP Network Projection program quit unexpectedly. Check the network

communication status, then turn the projector off and then on again.

04FE

256

Event ID code Cause and solution

0479 A projector system error has occurred. Turn the projector off and then on again.

04FF

0891 Cannot find an access point with the same SSID. Set your computer, access point,

and projector to the same SSID.

0892 The WPA/WPA2 authentication type does not match. Make sure the wireless

network security settings are correct.

0893 The WEP/TKIP/AES encryption type does not match. Make sure the wireless

network security settings are correct.

0894 Communication with unauthorized access point was disconnected. Contact your

network administrator.

0898 Failed to acquire DHCP. Make sure the DHCP server is operating correctly. If you

are not using DHCP, turn off the DHCP setting in the Network menus.

0899 A communication error has occurred. Try restarting the EasyMP Network Projection

program and restarting your projector. If that does not solve the problem, contact

Epson for help.

089A The EAP authentication type does not match the network. Check the wireless LAN

security settings and make sure that the security certificate is installed correctly.

089B EAP server authentication failed. Check the wireless LAN security settings and

make sure that the security certificate is installed correctly.

089C EAP client authentication failed. Check the wireless LAN security settings and make

sure that the security certificate is installed correctly.

089D Key exchange failed. Check the wireless LAN security settings and make sure that

the security certificate is installed correctly.

0B01 The internal storage could not be detected correctly. Select Delete All Internal Data

in the Basic menu under Whiteboard Settings. Turn off the projector and disconnect

the power cord, then reconnect the power cord and turn the projector back on. If that

does not solve the problem, contact Epson for help.

0BFF An error has occurred in the whiteboard function. Restart the projector.

Parent topic: Projector Information Display - Info Menu

257

Projector Reset Options - Reset Menu

You can reset most of the projector settings to their default values using the Reset All option on the

Reset menu.

You can also reset the projector's lamp usage timer to zero when you replace the lamp using the Reset

Lamp Hours option.

You cannot reset the following settings using the Reset All option:

• Input Signal

• User's Logo

• Language

• Network menu items

• Lamp Hours

• Password

• Zoom

• Image Shift

Parent topic: Adjusting the Menu Settings

258

Maintaining and Transporting the Projector

Follow the instructions in these sections to maintain your projector and transport it from place to place.

Projector Maintenance

Transporting the Projector

Projector Maintenance

Your projector needs little maintenance to keep working at its best.

You may need to clean the projection window and obstacle sensor periodically, and clean the air filter

and air vents to prevent the projector from overheating due to blocked ventilation.

The only parts you should replace are the lamp, air filter, pen batteries and tips, control pad batteries,

and remote control batteries. If any other part needs replacing, contact Epson or an authorized Epson

servicer.

Warning: Before cleaning any part of the projector, turn it off and unplug the power cord. Never open

any cover on the projector, except as specifically explained in this manual. Dangerous electrical voltages

in the projector can injure you severely.

Warning: Do not try to service this product yourself, except as specifically explained in this manual.

Refer all other servicing to qualified servicers.

Cleaning the Projection Window

Cleaning the Obstacle Sensor

Cleaning the Projector Case

Air Filter and Vent Maintenance

Projector Lamp Maintenance

Replacing the Remote Control Batteries

Replacing the Interactive Pen Batteries

Replacing the Interactive Pen Tips

Parent topic: Maintaining and Transporting the Projector

Cleaning the Projection Window

Clean the projection window periodically, or whenever you notice dust or smudges on the surface.

• To remove dust or smudges, gently wipe the projection window with lens-cleaning paper.

259

• To remove stubborn smudges, moisten a soft, lint-free cloth with lens cleaner and gently wipe the

projection window.

Warning: Do not use a lens cleaner that contains flammable gas. The high heat generated by the

projector lamp may cause a fire.

Caution: Do not use canned air, or the gases may leave a flammable residue.

Parent topic: Projector Maintenance

Related tasks

Turning Off the Projector

Cleaning the Obstacle Sensor

Clean the projector's obstacle sensor glass (circled in red) periodically, or if you see a message telling

you to remove any obstacles that are interfering with the projection area.

• To remove dust or smudges, gently wipe the obstacle sensor glass with lens-cleaning paper.

• To remove stubborn smudges, moisten a soft, lint-free cloth with lens cleaner and gently wipe the

obstacle sensor glass.

Warning: Do not use a lens cleaner that contains flammable gas. The high heat generated by the

projector lamp may cause a fire.

260

Caution: Do not use canned air, or the gases may leave a flammable residue.

Parent topic: Projector Maintenance

Related tasks

Turning Off the Projector

Cleaning the Projector Case

Before cleaning the projector case, turn off the projector and unplug the power cord.

• To remove dust or dirt, use a soft, dry, lint-free cloth.

• To remove stubborn dirt, use a soft cloth moistened with water and mild soap. Do not spray liquid

directly on the projector.

Caution: Do not use wax, alcohol, benzene, paint thinner, or other chemicals to clean the projector

case. These can damage the case. Do not use canned air, or the gases may leave a flammable

residue.

Parent topic: Projector Maintenance

Related tasks

Turning Off the Projector

Air Filter and Vent Maintenance

Regular filter maintenance is important to maintaining your projector. Your Epson projector is designed

with an easily accessible, user-replaceable filter to protect your projector and make regular maintenance

simple. Filter maintenance intervals will depend on the environment.

If regular maintenance is not performed, your Epson projector will notify you when the temperature

inside the projector has reached a high level. Do not wait until this warning appears to maintain your

projector filter as prolonged exposure to high temperatures may reduce the life of your projector or lamp.

Damage due to the failure to properly maintain the projector or its filter may not be covered by the

projector or lamp Limited Warranties.

Cleaning the Air Filter and Vents

Replacing the Air Filter

Parent topic: Projector Maintenance

Cleaning the Air Filter and Vents

Clean the projector's air filter or vents if they get dusty, or if you see a message telling you to clean them.

261

1. Turn off the projector and unplug the power cord.

2. Slide the air filter cover latch and open the air filter cover.

262

3. Pull the air filter out of the projector.

4. Vacuum the front of the air filter (the side with the tabs) to remove any remaining dust.

Note: If dust is difficult to remove or the air filter is damaged, replace the air filter.

263

5. Place the air filter back in the projector as shown.

6. Close the air filter cover.

Parent topic: Air Filter and Vent Maintenance

Related tasks

Turning Off the Projector

Replacing the Air Filter

You need to replace the air filter in the following situations:

• After cleaning the air filter, you see a message telling you to clean or replace it

• The air filter is torn or damaged

You can replace the air filter while the projector is mounted on the wall or ceiling.

1. Turn off the projector and unplug the power cord.

264

2. Slide the air filter cover latch and open the air filter cover.

265

3. Pull the air filter out of the projector.

Note: Air filters contain polypropylene. Dispose of used air filters according to local regulations.

266

4. Place the new air filter in the projector as shown.

5. Close the air filter cover.

Parent topic: Air Filter and Vent Maintenance

Related tasks

Turning Off the Projector

Projector Lamp Maintenance

The projector keeps track of the number of hours the lamp is used and displays this information in the

projector's menu system.

Replace the lamp as soon as possible when the following occurs:

• The projected image gets darker or starts to deteriorate

• A message appears when you turn on the projector telling you to replace the lamp

• The projector's lamp light is flashing orange and its power light is flashing blue

Replacing the Lamp

Resetting the Lamp Timer

267

Parent topic: Projector Maintenance

Replacing the Lamp

Before you replace the lamp, let the projector cool down for at least one hour so the lamp will not be hot.

Warning: Let the lamp fully cool before replacing it to avoid injury.

You can replace the lamp while the projector is mounted on the wall or ceiling.

1. Turn off the projector and unplug the power cord.

2. Allow the projector lamp to cool down for at least one hour.

Warning: If the lamp is broken, glass fragments may be loose inside the lamp chamber. Be careful

removing any broken glass to avoid injury. If the projector is mounted on the wall or ceiling, stand to

the side in case the lamp is broken.

3. Use the screwdriver included with the replacement lamp to loosen the screw securing the lamp

cover.

268

4. Slide off the lamp cover.

5. Loosen the screws securing the lamp to the projector. The screws do not come all the way out.

269

6. Lift up the lamp handle and gently pull the lamp out of the projector.

Note: The lamp(s) in this product contain mercury. Please consult your state and local

regulations regarding disposal or recycling. Do not put in the trash.

7. Gently insert the new lamp into the projector along the guide rail. If it does not fit easily, make sure it

is facing the right way. Press the handle down.

Caution: Do not touch any glass on the lamp assembly to avoid premature lamp failure.

270

8. Tighten the screws to secure the lamp.

9. Replace the lamp cover and tighten the screw to secure it.

Note: Be sure the lamp cover is securely installed or the lamp will not come on.

271

Reset the lamp timer to zero to keep track of the new lamp’s usage.

Parent topic: Projector Lamp Maintenance

Related tasks

Turning Off the Projector

Resetting the Lamp Timer

You must reset the lamp timer after replacing the projector's lamp to clear the lamp replacement

message and to keep track of lamp usage correctly.

Note: Do not reset the lamp timer if you have not replaced the lamp to avoid inaccurate lamp usage

information.

1. Turn on the projector.

2. Press the Menu button.

3. Select the Reset menu and press Enter.

4. Select Reset Lamp Hours and press Enter.

You see a prompt asking if you want to reset the lamp hours.

5. Select Yes and press Enter.

6. Press Menu or Esc to exit the menus.

272

Parent topic: Projector Lamp Maintenance

Replacing the Remote Control Batteries

The remote control uses two AA manganese or alkaline batteries. Replace the batteries as soon as they

run out.

Caution: Use only the type of batteries specified in this manual. Do not install batteries of different types,

or mix new and old batteries.

1. Open the battery cover as shown.

2. Remove the old batteries.

Warning: If the battery fluid has leaked, wipe it away with a soft cloth and avoid getting the fluid on

your hands. If it gets on your hands, wash them immediately to avoid injury.

273

3. Insert the batteries with the +and –ends facing as shown.

4. Close the battery cover and press it down until it clicks into place.

Warning: Dispose of used batteries according to local regulations. Do not expose batteries to heat

or flame. Keep batteries out of the reach of children; they are choking hazards and are very

dangerous if swallowed.

Parent topic: Projector Maintenance

Replacing the Interactive Pen Batteries

Each pen uses one AA alkaline or Sanyo Eneloop rechargeable battery. Replace the battery as soon as

it runs out.

274

When the battery is low, the pen light flashes as you turn on the switch. When the battery runs out, the

pen light goes out.

Caution: Use only the type of batteries specified in this manual.

1. Open the battery cover as shown.

2. Remove the old battery.

Warning: If the battery fluid has leaked, wipe it away with a soft cloth and avoid getting the fluid on

your hands. If it gets on your hands, wash them immediately to avoid injury.

3. Insert the battery with the +and –ends facing as shown.

275

4. Replace the battery cover and press it down until it clicks into place.

Warning: Dispose of used batteries according to local regulations. Do not expose batteries to heat

or flame. Keep batteries out of the reach of children; they are choking hazards and are very

dangerous if swallowed.

Parent topic: Projector Maintenance

Replacing the Interactive Pen Tips

If the pen tips become damaged or no longer work correctly, you can replace them.

1. Twist off the tip of the pen to remove it.

276

2. Twist on the new tip.

Parent topic: Projector Maintenance

Transporting the Projector

The projector contains precision parts, some of which are glass. Follow these guidelines to transport or

ship the projector safely:

• Remove any equipment connected to the projector.

• When transporting the projector a long distance or as checked luggage, pack it in a firm box with

cushioning around it and mark the box "Fragile."

• When shipping the projector for repairs, place it in its original packing materials, if possible, or use

equivalent materials with cushioning around the projector. Mark the box "Fragile."

Note: Epson shall not be liable for any damages incurred during transportation.

Parent topic: Maintaining and Transporting the Projector

277

Solving Problems

Check the solutions in these sections if you have any problems using the projector.

Projection Problem Tips

Projector Light Status

Using the Projector Help Displays

Solving Image or Sound Problems

Solving Projector or Remote Control Operation Problems

Solving Interactive Problems

Solving Network Problems

Where to Get Help

Projection Problem Tips

If the projector is not working properly, try turning it off and unplugging it. Then plug it back in and turn it

on.

If this does not solve the problem, check the following:

• The lights on the projector may indicate what the problem is.

• The solutions in this manual can help you solve many problems.

If none of these solutions help, you can contact Epson for technical support.

Parent topic: Solving Problems

Related references

Projector Light Status

278

Projector Light Status

The lights on the projector indicate the projector status and let you know when a problem occurs. Check

the status and color of the lights and look for a solution in the table here.

1 Power light

2 Status light

3 Lamp light

4 Temp (temperature) light

Power light Status light Lamp light Temp light Status and solution

Blue Blue Off Off Normal operation.

Blue Flashing blue Off Off Warming up. Wait for an image to

appear.

Shutting down. (When the Status light

stops flashing, you can unplug the

projector.)

279

Power light Status light Lamp light Temp light Status and solution

Blue Off Off Off Standby or sleep mode.

Network monitoring mode. The

projector is being monitored and

controlled over the network.

Off Flashing blue Off Orange Projector has overheated and turned

off. Leave it turned off to cool down.

After about five minutes, do the

following:

• Make sure that the vents and air

filter are not clogged with dust or

obstructed by nearby objects.

• Clean or replace the air filter.

• If operating the projector at high

altitude, turn on High Altitude

Mode.

• If the problem persists, unplug the

projector and contact Epson for

help.

Off Flashing blue Orange Off Lamp has a problem.

• Check to see if the lamp is burned

out, broken, or installed incorrectly.

Reseat or replace the lamp as

necessary.

• Clean or replace the air filter.

• If operating the projector at high

altitude, turn on High Altitude

Mode.

• If the problem persists, unplug the

projector and contact Epson for

help.

Flashing blue Varies Flashing

orange

Varies Replace the lamp soon to avoid

damage. Do not continue using the

projector.

280

Power light Status light Lamp light Temp light Status and solution

Off Flashing blue Off Flashing

orange

A fan or sensor has a problem. Turn

the projector off, unplug it, and

contact Epson for help.

Off Flashing blue Flashing

orange

Flashing

orange

Auto Iris error. Turn the projector off,

unplug it, and contact Epson for help.

Off Flashing blue Orange Orange Power error (ballast). Turn the

projector off, unplug it, and contact

Epson for help.

Obstacle detection error. A message

is displayed: "For safety purposes

remove any obstacles blocking the

lens."

• Remove any obstacles.

• Clean the obstacle sensor.

• If the detection error continues, turn

the projector off, unplug it, and

contact Epson for help.

Off Flashing blue Flashing

orange

Off Internal projector error. Turn the

projector off, unplug it, and contact

Epson for help.

Note: If the lights display a pattern not listed in the table above, turn the projector off, unplug it, and

contact Epson for help.

Parent topic: Solving Problems

Using the Projector Help Displays

You can display information to help you solve common problems using the projector's Help system.

1. Turn on the projector.

2. Press the Help button on the projector or the remote control.

You see the Help menu.

281

3. Use the up and down arrow buttons to highlight the problem you want to solve.

Note: You can also display image adjustment recommendations by pressing the left arrow button.

4. Press Enter to view the solutions.

5. When you are finished, do one of the following:

• To select another problem to solve, press Esc.

• To exit the help system, press Help.

Parent topic: Solving Problems

Solving Image or Sound Problems

Check the solutions in these sections if you have any problems with projected images or sound.

Solutions When No Image Appears

Solutions When Image is Incorrect Using the USB Display Function

Solutions When "No Signal" Message Appears

Solutions When "Not Supported" Message Appears

Solutions When Only a Partial Image Appears

Solutions When the Image is Not Rectangular

Solutions When the Image Contains Noise or Static

Solutions When the Image is Fuzzy or Blurry

Solutions When the Image Brightness or Colors are Incorrect

Solutions to Sound Problems

Parent topic: Solving Problems

Solutions When No Image Appears

If no image appears, try the following solutions:

• Press the A/V Mute button on the remote control to see if the image was temporarily turned off.

• Make sure all necessary cables are securely connected and the power is on for the projector and

connected video sources.

• Press the projector's power button to wake it from standby or sleep mode. Also see if your connected

computer is in sleep mode or displaying a blank screen saver.

• Check the settings on the Signal menu to make sure they are correct for the current video source.

282

• Adjust the Brightness setting or select the Normal Power Consumption setting.

• Check the Display setting to make sure Messages is set to On.

• If the projector does not respond when you press the control panel buttons, the buttons may be

locked. Unlock the buttons.

• If the projector does not respond when you press buttons on the remote control, make sure the remote

receivers are turned on.

• For images projected with Windows Media Center, reduce the screen size from full screen mode.

• For images projected from applications using Windows DirectX, turn off DirectX functions.

Parent topic: Solving Image or Sound Problems

Related references

Input Signal Settings - Signal Menu

Projector Feature Settings - Settings Menu

Related tasks

Unlocking the Projector's Buttons

Selecting an Image Source

Solutions When Image is Incorrect Using the USB Display Function

If no image appears or if the image appears incorrectly using the USB Display function, try the following

solutions:

• Press the Source Search button on the remote control or control pad and select USB Display.

• Make sure the USB Display software has installed correctly. Install it manually if necessary.

• Make sure the USB Type B setting in the Extended menu is set to one of the USB Display options.

• With Mac OS X, select the USB Display icon in the Dock or from the Applications folder.

• Change the computer's resolution to 1280 × 800.

• For images projected with Windows Media Center, reduce the screen size from full screen mode.

• For images projected from applications using Windows DirectX, turn off DirectX functions.

• If the mouse cursor flickers, select Make the movement of the mouse pointer smooth in the Epson

USB Display Settings program on your computer (feature not available with Windows 2000).

• Turn off the Transfer layered window setting in the Epson USB Display Settings program on your

computer.

Parent topic: Solving Image or Sound Problems

283

Related references

Projector Setup Settings - Extended Menu

Related tasks

Selecting an Image Source

Solutions When "No Signal" Message Appears

If the "No Signal" message appears, try the following solutions:

• Press the Source Search button and wait a few seconds for an image to appear.

• Turn on the connected computer or video source, and press its play button to begin your presentation,

if necessary.

• Check the connection from the projector to your video sources.

• If you are projecting from a laptop computer, make sure it is set up to display on an external monitor.

• If necessary, turn the projector and the connected computer or video source off and then on again.

Displaying From a PC Laptop

Displaying From a Mac Laptop

Parent topic: Solving Image or Sound Problems

Related tasks

Selecting an Image Source

Related topics

Connecting to Computer Sources

Connecting to Video Sources

Displaying From a PC Laptop

If you see the "No Signal" message when you display from a PC laptop, you need to set up the laptop to

display on an external monitor.

1. Hold down the laptop's Fn key and press the key labelled with a monitor icon or CRT/LCD. (See

your laptop manual for details.) Wait a few seconds for an image to appear.

2. To display on both the laptop's monitor and the projector, try pressing the same keys again.

3. If the same image is not displayed by the laptop and projector, check the Windows Display utility to

make sure the external monitor port is enabled and extended desktop mode is disabled. (See your

computer or Windows manual for instructions.)

284

4. If necessary, check your video card settings and set the multiple display option to Mirror or

Duplicate.

Parent topic: Solutions When "No Signal" Message Appears

Displaying From a Mac Laptop

If you see the "No Signal" message when you display from a Mac laptop, you need to set up the laptop

for mirrored display. (See your laptop manual for details.)

1. Open the System Preferences utility and select Displays.

2. Click the Arrangement tab.

3. Select the Mirror Displays checkbox.

Parent topic: Solutions When "No Signal" Message Appears

Solutions When "Not Supported" Message Appears

If the "Not Supported" message appears, try the following solutions:

• Make sure the correct input signal is selected on the Signal menu.

• Make sure the computer's display resolution does not exceed the projector's resolution and frequency

limit. If necessary, select a different display resolution for your computer. (See your computer manual

for details.)

Parent topic: Solving Image or Sound Problems

Related references

Input Signal Settings - Signal Menu

Solutions When Only a Partial Image Appears

If only a partial computer image appears, try the following solutions:

• Press the Auto button on the remote control to optimize the image signal.

• Try adjusting the image position using the Position menu setting.

• Press the Aspect button on the remote control to select a different image aspect ratio.

• If you zoomed into or out of the image using the E-Zoom buttons, press the Esc button until the

projector returns to a full display.

• Check your computer display settings to disable dual display and set the resolution within the

projector's limits. (See your computer manual for details.)

285

• Check the resolution assigned to your presentation files to see if they are created for a different

resolution than you are projecting in. (See your software help for details.)

Parent topic: Solving Image or Sound Problems

Related references

Input Signal Settings - Signal Menu

Related tasks

Changing the Image Aspect Ratio

Zooming Into and Out of Images

Solutions When the Image is Not Rectangular

If the projected image is not evenly rectangular, try the following solutions:

• If the projector is not mounted on the wall or ceiling, place it directly in front of the center of the screen,

facing it squarely, if possible.

• If you adjusted the projector height using the projector feet, press the keystone buttons on the

projector to adjust the image shape. (BrightLink Pro 1420Wi)

• Adjust the Quick Corner or Keystone setting to correct the image shape.

Note: Adjusting Quick Corner and Keystone settings may affect focus and pen calibration.

Parent topic: Solving Image or Sound Problems

Related tasks

Correcting Image Shape with the Keystone Buttons

Correcting Image Shape with Quick Corner

Solutions When the Image Contains Noise or Static

If the projected image seems to contain electronic interference (noise) or static, try the following

solutions:

• Check the cables connecting your computer or video source to the projector. They should be:

• Separated from the power cord to prevent interference

• Securely connected at both ends

• Not connected to an extension cable

• No longer than 10 feet (3 m) for VGA/computer cables or 24 feet (7.3 m) for HDMI cables

286

• Check the settings on the projector's Signal menu to make sure they match the video source.

• Select a computer video resolution and refresh rate that are compatible with the projector.

• Try a different cable.

Parent topic: Solving Image or Sound Problems

Related references

Input Signal Settings - Signal Menu

Supported Video Display Formats

Related topics

Connecting to Computer Sources

Connecting to Video Sources

Solutions When the Image is Fuzzy or Blurry

If the projected image is fuzzy or blurry, try the following solutions:

• Adjust the image focus.

• Check the projector lens cover glass for condensation.

Note: To avoid condensation on the lens after bringing the projector in from a cold environment, let the

projector warm up to room temperature before using it.

• Position the projector close enough to the screen, and directly in front of it.

• Position the projector so the keystone adjustment angle is not so wide that it distorts the image.

• Adjust the Sharpness setting to improve image quality.

• If you are projecting from a computer, press the Auto button on the remote control to automatically

adjust the tracking and sync. If any bands or overall blurriness remain, display a uniformly patterned

image on the screen and manually adjust the Tracking and Sync settings.

• If you are projecting from a computer, use a lower resolution.

Parent topic: Solving Image or Sound Problems

Related references

Image Quality Settings - Image Menu

Input Signal Settings - Signal Menu

Related tasks

Focusing the Image

287

Solutions When the Image Brightness or Colors are Incorrect

If the projected image is too dark or light, or the colors are incorrect, try the following solutions:

• Press the Color Mode button on the remote control to try different color modes for the image and

environment.

• Check your video source settings.

• Adjust the available settings on the Image menu for the current input source, such as Brightness,

Contrast,Tint,Color Adjustment, and/or Color Saturation.

• Make sure you selected the correct Input Signal or Video Signal setting on the Signal menu, if

available for your image source.

• Make sure all the cables are securely connected to the projector and your video device. If you

connected long cables, try connecting shorter cables.

• If you are using the ECO Power Consumption setting, try selecting Normal in the projector's menus.

• Position the projector close enough to the screen.

• If the image has been progressively darkening, you may need to replace the projector lamp soon.

Parent topic: Solving Image or Sound Problems

Related references

Image Quality Settings - Image Menu

Input Signal Settings - Signal Menu

Projector Setup Settings - ECO Menu

Related topics

Connecting to Computer Sources

Connecting to Video Sources

Solutions to Sound Problems

If there is no sound when you expect it or the volume is too low or high, try the following solutions:

• Adjust the projector's volume settings.

• Press the A/V Mute button on the remote control to resume video and audio if they were temporarily

stopped.

• Press the Source Search button to switch to the correct input source, if necessary.

• Check your computer or video source to make sure the volume is turned up and the audio output is set

for the correct source.

288

• Check the audio cable connections between the projector and your video source.

• If you do not hear sound from an HDMI source, set the connected device to PCM output.

• Make sure any connected audio cables are labeled "No Resistance".

• If you are using the USB Display function, turn on the Output audio from the projector setting in the

Epson USB Display Settings program on your computer.

• If you are using a Mac and you do not hear sound from an HDMI source, make sure your Mac

supports audio through the HDMI port. If not, you need to connect an audio cable.

• If you want to use a connected audio source when the projector is off, set the Standby Mode option to

Communication On and the A/V Output option to Always On.

• If you want to use a connected audio source when the projector is off, set the Standby Mode option to

A/V Standby.

• If you turn the projector on immediately after turning it off, the cooling fans may run at high speed

momentarily and cause an unexpected noise. This is normal.

Parent topic: Solving Image or Sound Problems

Related references

Projector Setup Settings - ECO Menu

Related tasks

Shutting Off the Picture and Sound Temporarily

Solving Projector or Remote Control Operation Problems

Check the solutions in these sections if you have problems operating the projector or remote control.

Solutions to Projector Power or Shut-Off Problems

Solutions to Problems with the Remote Control

Solutions to Password Problems

Solutions When the Source Cannot Be Changed

Parent topic: Solving Problems

Solutions to Projector Power or Shut-Off Problems

If the projector does not come on when you press the power button or it shuts off unexpectedly, try the

following solutions:

• Make sure the power cord is securely connected to the projector and to a working electrical outlet.

289

• The projector's buttons may be locked for security. Unlock the buttons or use the remote control to

turn on the projector.

• The power cord may be defective. Disconnect the cord and contact Epson.

• If the projector's lamp shuts off unexpectedly, it may have entered standby mode after a period of

inactivity. Press the power button to wake the projector.

• If the projector's lamp shuts off and the power and Temp lights are red, the projector has overheated

and shut off. Check the solutions for this light status.

• If the power button on the remote control does not turn on the projector, check its batteries and make

sure the Remote Receiver setting is turned on in the projector's menu, if available.

Parent topic: Solving Projector or Remote Control Operation Problems

Related references

Projector Light Status

Projector Feature Settings - Settings Menu

Related tasks

Unlocking the Projector's Buttons

Solutions to Problems with the Remote Control

If the projector does not respond to remote control commands, try the following solutions:

• Check that the remote control batteries are installed correctly and have power. If necessary, replace

the batteries.

• Make sure you are operating the remote control within the reception angle and range of the projector.

• Make sure the projector is not warming up or shutting down.

• Check to see if a button on the remote control is stuck down, causing it to enter sleep mode. Release

the button to wake the remote control up.

• Strong fluorescent lighting, direct sunlight, or infrared device signals may be interfering with the

projector's remote receivers. Dim the lights or move the projector away from the sun or interfering

equipment.

• If available, turn off one of the remote receivers in the projector's menu system, or check if all the

remote receivers were turned off.

• If you assigned an ID number to the remote control to operate multiple projectors, you may need to

check or change the ID setting (feature not available with all projectors).

• If you lose the remote control, you can order another one from Epson.

290

Parent topic: Solving Projector or Remote Control Operation Problems

Related references

Remote Control Operation

Related tasks

Replacing the Remote Control Batteries

Solutions to Password Problems

If you cannot enter or remember a password, try the following solutions:

• You may have turned on password protection without first setting a password. Try entering 0000 using

the remote control.

• If you have entered an incorrect password too many times and see a message displaying a request

code, write down the code and contact Epson. Do not attempt to enter the password again. Provide

the request code and proof of ownership for assistance in unlocking the projector.

• If you lose the remote control you cannot enter a password. Order a new one from Epson.

Parent topic: Solving Projector or Remote Control Operation Problems

Related concepts

Projector Security Features

Solutions When the Source Cannot Be Changed

If you are having trouble changing the source, make sure the projector is not opening an image,

scanning, saving, or printing at the same time. Close all projector menus and dialogs. These processes

may take time to complete, and the source cannot be changed during processing.

Parent topic: Solving Projector or Remote Control Operation Problems

Solving Interactive Problems

Check the solutions in these sections if you have problems using the interactive system.

Solutions When "Error Occurred in the Easy Interactive Function" Message Appears

Solutions When the Interactive Pens Do Not Work

Solutions When the Interactive Pen Position Is Not Accurate

Solutions When Manual Calibration Does Not Work

Solutions When the Interactive Pens Are Slow or Difficult to Use

Solutions When the Interactive Pens Cause Interference or Unwanted Effects

291

Solutions When Finger Touch Interactivity Does Not Work

Solutions for Problems With Capturing, Printing, Saving, or Scanning

Solutions When Inking Does Not Appear in Microsoft Office

Solutions When the Pen Does Not Work Over a Network or the Toolbars Do Not Appear

Solutions When the Time Is Incorrect in Whiteboard Settings

Parent topic: Solving Problems

Solutions When "Error Occurred in the Easy Interactive Function" Message Appears

If the "Error occurred in the Easy Interactive Function" message appears, contact Epson for help.

Parent topic: Solving Interactive Problems

Solutions When the Interactive Pens Do Not Work

If the interactive pens do not work, try the following solutions:

• The pens turn off automatically if you forget to turn them off. Tap the pen tip or press the

power/function button to turn the pen back on.

• Make sure you are not covering the black section near the tip of the pen.

• Make sure nothing is blocking the signal between the pen and the interactive pen receiver on the

projector.

• Try holding the pen at a different angle so that your hand is not blocking the signal.

• Make sure the cable cover is in place to keep cables from blocking the signal.

• Make sure the pen battery has enough power. Try replacing the battery.

• If you are projecting from a computer, make sure the USB cable is connected to the computer and

projector.

• Dim the room lights and turn off any fluorescent lights. Make sure the projection surface and pen

receiver are not in direct sunlight or other sources of bright lighting.

• Remove any decorative lights from around the projector or projection surface.

• If the pen tip is worn out or damaged, you may need to replace it.

• Make sure the interactive pen receiver on the projector is clean and free from dust.

• Make sure there is no interference from infrared remote controls, mice, or infrared microphones.

• Make sure the USB Type B option on the Extended menu is set to Easy Interactive Function or USB

Display/Easy Interactive Function.

292

• Make sure you have calibrated the system. Try recalibrating.

• If you are projecting from a laptop computer, make sure the battery has enough power, or connect the

laptop to a power outlet.

• Make sure the Pen Mode and Pen Operation Mode settings are set correctly in the Easy Interactive

Function options on the Extended menu.

• If you are using multiple projectors in the same room, change the Distance of Projectors setting in

Easy Interactive Function >Advanced on the Extended menu.

Parent topic: Solving Interactive Problems

Related tasks

Replacing the Interactive Pen Tips

Replacing the Interactive Pen Batteries

Solutions When the Interactive Pen Position Is Not Accurate

If the pen position is not the same as the mouse pointer, try the following solutions:

• Make sure you have calibrated the system. Try manual calibration.

• Make sure the cable cover is in place to keep cables from blocking the signal.

• Try adjusting the pen operation area.

• If you use the E-Zoom + button on the remote control to enlarge the image, the pen position is not

accurate. When you return the image to the original size, the position should be correct.

• In PC Interactive mode (in the Extended > Advanced menu), turn off Auto Adjust Pen Area and

select Manual Adj. Pen Area.

• Try changing the computer's resolution to 1280 × 800.

Parent topic: Solving Interactive Problems

Related concepts

Pen Calibration

Related references

Projector Setup Settings - Extended Menu

Related tasks

Adjusting the Pen Operation Area

Zooming Into and Out of Images

Removing and Attaching the Cable Cover

293

Solutions When Manual Calibration Does Not Work

If you are having trouble calibrating manually, try the following solutions:

• If the circle does not move to the next position, or it moves automatically, dim or turn off any bright

lights near the projection surface.

• Make sure the projector is not too close to the projection surface.

Parent topic: Solving Interactive Problems

Solutions When the Interactive Pens Are Slow or Difficult to Use

If the pens are difficult to use or respond too slowly, try the following solutions:

• For easier operation, hold the pen perpendicular to the projection surface.

• For the best performance, connect your computer to the projector using a VGA or HDMI cable for

display and the USB cable for interactivity.

• If you are using a computer, try setting your computer's display to 1280 × 800.

• If you are using USB Display in Windows, you may need to disable Windows Aero in the Epson USB

Display Settings program on your computer.

• If you are projecting over a network, see the EasyMP Network Projection Operation Guide for

performance adjustment instructions.

Parent topic: Solving Interactive Problems

Related tasks

Using the Pens

Solutions When the Interactive Pens Cause Interference or Unwanted Effects

If the pens are causing interference or unwanted effects, try the following solutions:

• When both pens are used at the same time, make sure they are approximately 4 inches (10.16 cm)

apart.

• Turn off the pens when they are not in use.

• Do not rest the pens on the image area of an interactive table, to avoid interference with your

computer's mouse.

• Try changing the Number of Pen Users setting from One User to Two Users. (BrightLink Pro

1420Wi)

• Turn off hovering.

294

Parent topic: Solving Interactive Problems

Related references

Projector Setup Settings - Extended Menu

Solutions When Finger Touch Interactivity Does Not Work

If finger touch interactivity does not work (BrightLink Pro 1430Wi), try the following solutions:

• Make sure the Touch Unit is installed correctly and the power cable is properly connected. See your

mount's Installation Guide for details.

• If the light on the Touch Unit is not on, check the Touch Unit Setup settings in the Easy Interactive

Function option on the Extended menu and make sure the Power setting is set to On.

• Adjust the angle on the Touch Unit.

• Make sure there are no obstacles (such as cables or pen trays) between the Touch Unit's laser

diffusion ports and the projection surface.

• Remove any decorative lights from around the projector or projection surface.

• Make sure there is no interference from infrared remote controls, mice, or infrared microphones.

• Make sure you have performed pen calibration and finger touch calibration. Try recalibrating.

Parent topic: Solving Interactive Problems

Related concepts

Pen Calibration

Related tasks

Adjusting the Angle of the Touch Unit

Calibrating for Finger Touch Interactivity

Solutions for Problems With Capturing, Printing, Saving, or Scanning

If you are having trouble capturing and pasting, or printing, saving, or scanning, try the following

solutions:

• If you start a process using one of the pens, you must complete it using the pen. If you start using the

remote control or control pad, you must complete the process using the remote control or control pad.

• If you are having trouble pasting a captured image, make sure the image is not protected.

• If a black frame appears around a pasted image, it may be because the image was shifted or resized.

• If you are having trouble printing or scanning, make sure the printer is not out of ink, jammed, or in any

other error state.

295

• For USB printing or scanning, make sure a USB cable is connected between the projector's USB-A

port and the USB-B port on the control pad. Make sure another USB cable is connected between the

Printer port on the control pad and the printer itself.

• For USB printing or scanning, try connecting a different USB cable, and make sure the cables are less

than 16 ft (4.9 m) long.

• Connect only one printer or multifunction device at a time, and make sure the device is supported by

the projector.

• Check the Whiteboard Settings on the Extended menu.

Parent topic: Solving Interactive Problems

Related references

Projector Setup Settings - Extended Menu

Supported Printer Types

Related tasks

Connecting a Printer to the Control Pad

Solutions When Inking Does Not Appear in Microsoft Office

If Start Inking does not appear on the Review tab in your Microsoft Office application, try this solution.

Open the projector's Extended menu and change the following settings in Easy Interactive Function:

BrightLink Pro 1420Wi:

• Set the Number of Pen Users to One User.

• Set the Pen Operation Mode to Pen.

BrightLink Pro 1430Wi:

Change the Pen Operation Mode setting.

Parent topic: Solving Interactive Problems

Related references

Projector Setup Settings - Extended Menu

296

Solutions When the Pen Does Not Work Over a Network or the Toolbars Do Not Appear

If you are having trouble using the pen with a network connection, or the toolbars do not appear on your

projected image, try the following solutions:

• If you are using EasyMP Network Projection software, select Options, then make sure Use

Interactive Pen is enabled. Also, select the Adjust performance tab and select Transfer layered

window.

• If you are using the Quick Wireless Connection USB Key, start the Epson Quick Wireless Connections

Settings program on your computer, select the General settings tab, then make sure Use Interactive

Pen is enabled. Also, select the Adjust performance tab and select Transfer layered window.

Parent topic: Solving Interactive Problems

Solutions When the Time Is Incorrect in Whiteboard Settings

If the time is incorrect on internal storage settings for whiteboard mode, you may need to update the

Time/Schedule Settings on the Extended menu.

Parent topic: Solving Interactive Problems

Related references

Projector Setup Settings - Extended Menu

Solving Network Problems

Check the solutions in these sections if you have problems using the projector on a network.

Solutions When Wireless Authentication Fails

Solutions When You Cannot Access the Projector Through the Web

Solutions When Network Alert E-Mails are Not Received

Parent topic: Solving Problems

Solutions When Wireless Authentication Fails

• If the wireless settings are correct, but authentication fails, you may need to update the

Time/Schedule Settings on the Extended menu.

• Check the Security settings and passphrase in the Network Configuration menu.

Parent topic: Solving Network Problems

Related references

Projector Setup Settings - Extended Menu

297

Projector Network Settings - Network Menu

Solutions When You Cannot Access the Projector Through the Web

If you are unable to access the projector through a web browser, make sure you are using the correct ID

and password, which are case sensitive.

• For the user ID, enter EPSONWEB. (You cannot change the user ID.)

• For the password, enter the password set in the projector's Network menu. The default password is

admin.

• Make sure you have access to the network the projector is on.

Note: The user ID and password are case sensitive.

Parent topic: Solving Network Problems

Related tasks

Controlling a Networked Projector Using a Web Browser

Solutions When Network Alert E-Mails are Not Received

If you do not receive an e-mail alerting you to problems with a projector over the network, try the

following solutions:

• Make sure the projector is turned on and connected to the network correctly. (If an error shut down the

projector, it cannot send an e-mail.)

• Make sure you set up the projector e-mail alert settings correctly on the projector's network Mail menu

or in the network software.

Parent topic: Solving Network Problems

Related references

Network Projector E-mail Alert Messages

Related tasks

Setting Up Projector Network E-Mail Alerts

Where to Get Help

If you need to contact Epson for technical support services, use the following support options.

298

Internet Support

Visit Epson's support website at epson.com/support (U.S.) or epson.ca/support (Canada) for solutions to

common problems with your projector. You can download utilities and documentation, get FAQs and

troubleshooting advice, or e-mail Epson with your questions.

Speak to a Support Representative

To use the Epson PrivateLine Support service, call (800) 637-7661. This service is available for the

duration of your warranty period. You may also speak with a projector support specialist by dialing (562)

276-4394 (U.S.) or (905) 709-3839 (Canada).

Support hours are 6 AM to 8 PM, Pacific Time, Monday through Friday and 7 AM to 4 PM, Pacific Time,

Saturday.

Days and hours of support are subject to change without notice. Toll or long distance charges may

apply.

Before you call, have the following information ready:

• Product name

• Product serial number (located on the bottom or rear of the projector, or in the menu system)

• Proof of purchase (such as a store receipt) and date of purchase

• Computer or video configuration

• Description of the problem

Purchase Supplies and Accessories

You can purchase screens, other optional accessories, and replacement parts from an Epson authorized

reseller. To find the nearest reseller, call 800-GO-EPSON (800-463-7766). Or you can purchase online

at epsonstore.com (U.S. sales) or epson.ca (Canadian sales).

To purchase a replacement remote control, call (562) 276-4394 (U.S.) or (905) 709-3839 (for dealer

referral in Canada).

Parent topic: Solving Problems

Related references

Projector Light Status

299

Technical Specifications

These sections list the technical specifications of your projector.

General Projector Specifications

Projector Lamp Specifications

Remote Control Specifications

Interactive Pen Specifications

Touch Unit Specifications

Projector Dimension Specifications

Projector Electrical Specifications

Projector Environmental Specifications

Projector Safety and Approvals Specifications

Supported Video Display Formats

USB Display System Requirements

General Projector Specifications

Type of display Poly-silicon TFT active matrix

Resolution 1280 × 800 pixels (WXGA)

Lens F=1.80

Focal length: 3.71 mm

Color reproduction Full color, up to 1 billion colors

Brightness Normal Power Consumption mode:

White light output 3300 lumens (ISO 21118 standard)

Color light output 3300 lumens

ECO Power Consumption mode:

White light output 1900 lumens (ISO 21118 standard)

Note: Color brightness (color light output) and white brightness

(white light output) will vary depending on usage conditions. Color

light output measured in accordance with IDMS 15.4; white light

output measured in accordance with ISO 21118.

300

Contrast ratio 10000:1 with Auto Iris on and Normal Power Consumption mode

Image size

(in native aspect ratio)

60 inches (1.54 m) to 100 inches (2.54 m)

Projection distance

(in native aspect ratio)

13.7 inches (0.348 m) to 23.5 inches (0.597 m)

Projection methods Front, rear, ceiling-mounted, table projection

Optical aspect ratio

(width-to-height)

16:10

Focus adjustment Manual

Zoom adjustment Digital

Zoom ratio

(Tele-to-Wide)

1.0 to 1.35

Internal sound system 16 W monaural

Noise level 35 dB (Normal Power Consumption mode)

28 dB (ECO Power Consumption mode)

Keystone correction angle Vertical: ± 3°

Horizontal: ± 3°

USB Type B port compatibility One USB 1.1 and 2.0 compliant port for USB display, external

mouse, interactivity

USB Type A port compatibility One USB 1.1 and 2.0 compliant port for USB device input

One USB 1.1 and 2.0 compliant port for Epson document camera

display

Parent topic: Technical Specifications

Projector Lamp Specifications

Type UHE (Ultra High Efficiency)

Power consumption 245 W

301

Lamp life Normal Power Consumption mode:

Up to about 4000 hours

ECO Power Consumption mode:

Up to about 6000 hours

Note: Turn off this product when not in use to prolong the life of the projector. Lamp life will vary

depending upon mode selected, environmental conditions, and usage. Brightness decreases over time.

Parent topic: Technical Specifications

Remote Control Specifications

Reception range 19.7 feet (6 m)

Batteries Two alkaline or manganese AA

Parent topic: Technical Specifications

Interactive Pen Specifications

Batteries One AA alkaline

Size 6.3 inches (161 mm) long; diameter 0.94 inches (24 mm)

Weight 1.06 oz (30 g), excluding the battery

Parent topic: Technical Specifications

Touch Unit Specifications

The Touch Unit comes only with the BrightLink Pro 1430Wi.

Technology Infrared Laser (Class 1)

Dimensions Height: 3.7 inches (95 mm)

Width: 8.2 inches (207 mm)

Depth: 2 inches (51 mm)

Weight 15.9 oz (450 g)

302

Parent topic: Technical Specifications

Projector Dimension Specifications

Height (excluding feet) 6.1 inches (155 mm)

Width 14.4 inches (367 mm)

Depth 14.8 inches (375 mm)

Weight 12.3 lb (5.6 kg)

Parent topic: Technical Specifications

Projector Electrical Specifications

Rated frequency 50/60 Hz

Power supply 100 to 240 VAC ±10%

3.8 to 1.7 A

Power consumption

(100 to 120 V)

Operating:

Normal Power Consumption mode: 384 W

ECO Power Consumption mode: 288 W

Standby:

0.31 W (Communication Off), 2.4 W (Communication On)

Power consumption

(220 to 240 V)

Operating:

Normal Power Consumption mode: 365 W

ECO Power Consumption mode: 274 W

Standby:

0.42 W (Communication Off), 2.5 W (Communication On)

Parent topic: Technical Specifications

303

Projector Environmental Specifications

Temperature Operating:

Up to 4921 feet (1500 m): 41 to 95 °F (5 to 35 °C)

4921 feet (1500 m) to 9843 feet (3000 m) : 41 to 86 °F (5 to 30 °C)

Storage: 14 to 140 °F (–10 to 60 °C)

Humidity (relative, non-

condensing)

Operating: 20 to 80%

Storage: 10 to 90%

Operating altitude Up to 4921 feet (1500 m)

Up to 9843 feet (3000 m) with High Altitude Mode enabled

Parent topic: Technical Specifications

Projector Safety and Approvals Specifications

United States FCC Part 15 Class B (DoC)

UL60950-1 2nd edition (cTUVus Mark)

Canada ICES-003 Class B

CSA C22.2 No. 60950-1

Parent topic: Technical Specifications

Supported Video Display Formats

For best results, your computer's monitor port or video card resolution should be set to display in the

projector's native resolution. However, your projector includes Epson's SizeWise chip that supports other

computer display resolutions, so your image will be resized to fit automatically.

Your computer's monitor port or video card refresh rate (vertical frequency) must be compatible with the

projector. (See your computer or video card manual for details.)

The table here lists the compatible refresh rate and resolution for each compatible video display format.

Display format Refresh rate (in Hz) Resolution (in pixels)

Computer signals (analog RGB)

304

Display format Refresh rate (in Hz) Resolution (in pixels)

VGA 60/72/75/85 640 × 480

SVGA 56/60/72/75/85 800 × 600

XGA 60/70/75/85 1024 × 768

WXGA 60 1280 × 768

60 1366 × 768

60/75/85 1280 × 800

WXGA+ 60/75/85 1440 × 900

WXGA++ 60 1600 × 900

SXGA 70/75/85 1152 × 864

60/75/85 1280 × 1024

60/75/85 1280 × 960

SXGA+ 60/75 1400 × 1050

WSXGA+* 60 1680 × 1050

UXGA 60 1600 × 1200

MAC13" 67 640 × 480

MAC16" 75 832 × 624

MAC19" 75 1024 × 768

59 1024 × 768

MAC21" 75 1152 × 870

Composite video

TV (NTSC) 60 720 × 480

TV (SECAM) 50 720 × 576

TV (PAL) 50/60 720 × 576

Component video

SDTV (480i) 60 720 × 480

SDTV (576i) 50 720 × 576

305

Display format Refresh rate (in Hz) Resolution (in pixels)

SDTV (480p) 60 720 × 480

SDTV (576p) 50 720 × 576

HDTV (720p) 50/60 1280 × 720

HDTV (1080i) 50/60 1920 × 1080

HDMI input signals

VGA 60 640 × 480

SVGA 60 800 × 600

XGA 60 1024 × 768

WXGA 60 1280 × 800

60 1366 × 768

WXGA+ 60 1440 × 900

WXGA++ 60 1600 × 900

WSXGA+ 60 1680 × 1050

SXGA 60 1280 × 960

60 1280 × 1024

SXGA+ 60 1400 × 1050

UXGA 60 1600 × 1200

SDTV (480i/480p) 60 720 × 480

SDTV (576i/576p) 50 720 × 576

HDTV (720p) 50/60 1280 × 720

HDTV (1080i) 50/60 1920 × 1080

HDTV (1080p) 24/30/50/60 1920 × 1080

MHL input signals

VGA 60 640 × 480

SDTV (480i/480p) 60 720 × 480

SDTV (576i/576p) 50 720 × 576

306

Display format Refresh rate (in Hz) Resolution (in pixels)

HDTV (720p) 50/60 1280 × 720

HDTV (1080i) 50/60 1920 × 1080

HDTV (1080p) 24/30 1920 × 1080

*Wide resolution only

Parent topic: Technical Specifications

USB Display System Requirements

Your computer system must meet the system requirements here to use the projector's USB Display

software.

Requirement Windows Mac

Operating system Windows XP Professional, Home

Edition, and Tablet PC Edition (32-bit)

OS X 10.5.x (32-bit), and 10.6.x,

10.7.x , 10.8.x, 10.9.x (32- and 64-

bit)

Windows Vista Ultimate, Enterprise,

Business, Home Premium, and Home

Basic (32-bit)

Windows 7 Ultimate, Enterprise,

Professional, and Home Premium (32-

and 64-bit); Home Basic and Starter (32-

bit)

Windows 8.x, Pro, and Enterprise (32-

and 64-bit)

USB version USB 1.1 and above (USB 2.0 recommended)

CPU Mobile Pentium III 1.2 GHz or faster

(1.6 GHz or faster recommended)

Power PC G4 1 GHz or faster (Core

Duo 1.83 GHz or faster

recommended)

Memory 256MB or more (512MB or more

recommended)

512MB or more

Hard disk space 20MB or more

Display Resolution between 640 × 480 and 1600 × 1200, 16-bit color or greater

307

Parent topic: Technical Specifications

Related references

Projector Setup Settings - Extended Menu

308

Notices

Check these sections for important notices about your projector.

Recycling

Important Safety Information

Important Safety Instructions

FCC Compliance Statement

Wireless Telegraphy Act Regulations

Trademarks

Open Source Software License

Recycling

Epson offers a recycling program for end of life products. Please go to epson.com/recycle for information

on how to return your products for proper disposal.

Parent topic: Notices

Important Safety Information

Caution: Never look into the projector lens when the lamp is turned on; the bright light can damage your

eyes. Never let children look into the lens when it is on. Never open any cover on the projector, except

the lamp and filter covers. Dangerous electrical voltages inside the projector can severely injure you.

Except as specifically explained in this User's Guide, do not attempt to service this product yourself.

Refer all servicing to qualified service personnel.

Warning: The projector and its accessories come packaged in plastic bags. Keep plastic bags away

from small children to avoid any risk of suffocation.

Caution: When you replace the lamp, never touch the new lamp with your bare hands; the invisible

residue left by the oil on your hands may shorten the lamp life. Use a cloth or glove to handle the new

lamp.

Parent topic: Notices

309

Important Safety Instructions

Follow these safety instructions when setting up and using the projector:

• Do not look into the lens when the projector is on. The bright light can damage your eyes. Avoid

standing in front of the projector so the bright light does not shine into your eyes.

• Do not place the projector on an unstable cart, stand, or table.

• Do not operate the projector on its side, or while tilted to one side. Do not tilt the projector more than 3°

forward or back.

• If the projector is mounted on a ceiling or wall, it should be installed by qualified technicians using

mounting hardware designed for use with this projector.

• When installing or adjusting a ceiling or wall mount, do not use adhesives to prevent the screws from

loosening and do not use oils or lubricants. This may cause the projector case to crack and the

projector to fall from its ceiling mount. This could cause serious injury to anyone under the mount and

could damage the projector.

• Do not use the projector near water, sources of heat, high-voltage electrical wires, or sources of

magnetic fields.

• Use the type of power source indicated on the projector. Use of a different power source may result in

fire or electric shock. If you are not sure of the power available, consult your dealer or power company.

• Place the projector near a wall outlet where the plug can be easily unplugged.

• Take the following precautions when handling the plug: Do not hold the plug with wet hands. Do not

insert the plug into a dusty outlet. Insert the plug firmly into the outlet. Do not pull the power cord when

disconnecting the plug; always be sure to hold the plug when disconnecting it. Do not overload wall

outlets, extension cords, or power strips. Failure to comply with these precautions could result in fire or

electric shock.

• Do not place the projector where the cord can be walked on. This may result in fraying or damage to

the plug.

• Unplug the projector from the wall outlet before cleaning. Use a dry cloth (or, for stubborn dirt or

stains, a moist cloth that has been wrung dry) for cleaning. Do not use liquid or aerosol cleaners, any

sprays containing flammable gas, or solvents such as alcohol, paint thinner, or benzine.

• Do not block the slots and openings in the projector case. They provide ventilation and prevent the

projector from overheating. Do not operate the projector on a sofa, rug, or other soft surface, or set it

on top of loose papers. Do not cover the projector with a blanket, curtain, or tablecloth. If you are

setting up the projector near a wall, leave at least 7.9 inches (20 cm) of space between the wall and

the air exhaust vent.

• Do not operate the projector in a closed-in cabinet unless proper ventilation is provided.

310

• Never allow objects of any kind to enter any openings in the projector. Do not leave objects, especially

flammable objects, near the projector. Never spill liquid of any kind into the projector.

• If you are using two or more projectors side-by-side, leave at least 2 feet (60 cm) of space between the

projectors to allow for proper ventilation.

• You may need to clean the air filter and vent. A clogged air filter or vent can block ventilation needed

to cool the projector. Do not use canned air, or the gases may leave a residue.

• Do not store the projector outdoors for an extended length of time.

• Except as specifically explained in this manual, do not attempt to service this product yourself. Refer

all servicing to qualified personnel. Opening or removing covers may expose you to dangerous

voltages and other hazards.

• Never open any covers on the projector except as specifically explained in this manual. Never attempt

to disassemble or modify the projector. Refer all repairs to qualified service personnel.

• Unplug the projector from the wall outlet and refer servicing to qualified service personnel under the

following conditions: if it does not operate normally when you follow the operating instructions, or

exhibits a distinct change in performance; if smoke, strange odors, or strange noises come from the

projector; if the power cord or plug is damaged or frayed; if liquid or foreign objects get inside the

projector, or if it has been exposed to rain or water; if it has been dropped or the housing has been

damaged.

• Do not touch the plug during an electrical storm. Otherwise, you may receive an electric shock.

• Unplug the projector when it will not be used for extended periods.

• Do not use the projector where it may be exposed to rain, water, or excessive humidity.

• Do not use or store the projector where it may be exposed to smoke, steam, corrosive gases,

excessive dust, vibration, or shock.

• Do not use the projector where flammable or explosive gases may be present.

• Do not use or store the projector or remote control in a hot location, such as near a heater, in direct

sunlight, or in a closed vehicle.

• If you use the projector in a country other than where you purchased it, use the correct power cord for

that country.

• Do not stand on the projector or place heavy objects on it.

• Do not use the projector outside of the required temperature range of 41 to 95 °F (5 to 35 °C) at an

altitude of 4921 feet (1500 m) or less, or 41 to 86 °F (5 to 30 °C) at a higher altitude. Doing so may

cause an unstable display and could lead to projector damage. Do not use or store the projector where

it may be exposed to sudden changes in temperature.

311

• Do not store the projector outside of the required temperature range of 14 to 140 °F (–10 to 60 °C) or

in direct sunlight for long periods of time. Doing so may cause damage to the case.

• Do not place anything that can become warped or damaged by heat near the exhaust vents. Do not

bring your hands or face close to the vents while projection is in progress. Do not bring your face close

to the projector while it is in use.

• Before you move the projector, make sure its power is turned off, the plug is disconnected from the

outlet, and all cables are disconnected.

• Never try to remove the lamp immediately after use because it will be extremely hot. Before removing

the lamp, turn off the power and wait at least an hour to allow the lamp to cool completely.

• Do not disassemble the lamp or subject it to impacts.

• Do not place the source of an open flame, such as a lit candle, on or near the projector.

• Do not block the lens during projection using a book or any other object. This could damage the

projector or cause a fire.

• Do not modify the power cord. Do not place heavy objects on top of the power cord or bend, twist, or

pull it excessively. Keep the power cord away from hot electrical appliances.

• If the lamp breaks, ventilate the room to prevent gases contained in the lamp from being inhaled or

coming in contact with your eyes or mouth. If you do inhale gases or gases come in contact with your

eyes or mouth, seek medical advice immediately.

• If the projector is mounted overhead and the lamp breaks, be careful to prevent pieces of glass from

falling into your eyes or mouth when you open the lamp cover. If pieces of glass do get into your eyes

or mouth, seek medical advise immediately.

• Always lower the volume before turning off the projector. Turning on the projector with the volume too

high can damage your ears.

• Do not store the interactive pens or the batteries in a hot location, such as near a heater, in direct

sunlight, or in a closed vehicle.

• Remove the batteries from the interactive pens if you will not be using the pens for a long time.

Note: The lamp(s) in this product contain mercury. Please consult your state and local regulations

regarding disposal or recycling. Do not put in the trash.

WARNING: The cords included with this product contain chemicals, including lead, known to the State of

California to cause birth defects or other reproductive harm. Wash hands after handling. (This notice is

provided in accordance with Proposition 65 in Cal. Health & Safety Code § 25249.5 and following.)

Restriction of Use

312

Parent topic: Notices

Restriction of Use

When this product is used for applications requiring high reliability/safety such as transportation devices

related to aviation, rail, marine, automotive; disaster prevention devices; various safety devices; or

functional/precision devices, you should use this product only after giving consideration to including fail-

safes and redundancies into your design to maintain safety and total system reliability.

Because this product was not intended for use in applications requiring extremely high reliability/safety

such as aerospace equipment, main communication equipment, nuclear power control equipment, or

medical equipment related to direct medical care, please make your own judgment on this product's

suitability after a full evaluation.

Parent topic: Important Safety Instructions

FCC Compliance Statement

For United States Users

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interference will not occur in

a particular installation. If this equipment does cause interference to radio and television reception, which

can be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

WARNING

The connection of a non-shielded equipment interface cable to this equipment will invalidate the FCC

Certification or Declaration of this device and may cause interference levels which exceed the limits

established by the FCC for this equipment. It is the responsibility of the user to obtain and use a shielded

equipment interface cable with this device. If this equipment has more than one interface connector, do

not leave cables connected to unused interfaces. Changes or modifications not expressly approved by

the manufacturer could void the user’s authority to operate the equipment.

313

For Canadian Users

CAN ICES-3(B)/NMB-3(B)

Parent topic: Notices

Wireless Telegraphy Act Regulations

The following acts are prohibited by the Wireless Telegraphy Act:

• Modifying and disassembling (including the antenna)

• Removing the label of conformance

Parent topic: Notices

Trademarks

EPSON®, EasyMP®, Instant Off®, and Quick Corner®are registered trademarks, and EPSON Exceed

Your Vision is a registered logomark of Seiko Epson Corporation.

PrivateLine®is a registered trademark; SizeWiseTM is a trademark; and Epson StoreSM and Extra CareSM

are service marks of Epson America, Inc.

Mac and OS X are trademarks of Apple Inc., registered in the U.S. and other countries.

HDMI and High-Definition Multimedia Interface are the trademarks or registered trademarks of HDMI

Licensing LLC.

General Notice: Other product names used herein are for identification purposes only and may be

trademarks of their respective owners. Epson disclaims any and all rights in those marks.

Parent topic: Notices

Open Source Software License

GNU GPL

This projector product includes the open source software programs which apply the GNU General Public

License Version 2 or later version ("GPL Programs").

314

We provide the source code of the GPL Programs until five (5) years after the discontinuation of same

model of this projector product.

If you desire to receive the source code of the GPL Programs, contact Epson as described in the User's

Guide .

These GPL Programs are WITHOUT ANY WARRANTY; without even the implied warranty of

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public

License for more details.

The list of GPL Programs is as follows and the names of author are described in the source code of the

GPL Programs

The list of GPL Programs

busybox-1.13.4

iptables-1.4.4

libgcc1(gcc-4.3.3)

libstdc++-6.0.10

linux-2.6.27

patches

udhcp 0.9.8

uvc rev.219

wireless_tools 29

EPSON original drivers

The GNU General Public License Version 2 is as follows. You also can see the GNU General Public

License Version 2 at http://www.gnu.org/licenses/.

GNU GENERAL PUBLIC LICENSE

Version 2, June 1991

02110-1301 USA Everyone is permitted to copy and distribute verbatim copies of this license document,

but changing it is not allowed.

Preamble

The licenses for most software are designed to take away your freedom to share and change it. By

contrast, the GNU General Public License is intended to guarantee your freedom to share and change

free software--to make sure the software is free for all its users. This General Public License applies to

most of the Free Software Foundation's software and to any other program whose authors commit to

315

using it. (Some other Free Software Foundation software is covered by the GNU Lesser General Public

License instead.) You can apply it to your programs, too.

When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are

designed to make sure that you have the freedom to distribute copies of free software (and charge for

this service if you wish), that you receive source code or can get it if you want it, that you can change the

software or use pieces of it in new free programs; and that you know you can do these things.

To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask

you to surrender the rights. These restrictions translate to certain responsibilities for you if you distribute

copies of the software, or if you modify it.

For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the

recipients all the rights that you have. You must make sure that they, too, receive or can get the source

code. And you must show them these terms so they know their rights.

We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which

gives you legal permission to copy, distribute and/or modify the software.

Also, for each author's protection and ours, we want to make certain that everyone understands that

there is no warranty for this free software. If the software is modified by someone else and passed on,

we want its recipients to know that what they have is not the original, so that any problems introduced by

others will not reflect on the original authors' reputations.

Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that

redistributors of a free program will individually obtain patent licenses, in effect making the program

proprietary. To prevent this, we have made it clear that any patent must be licensed for everyone's free

use or not licensed at all.

The precise terms and conditions for copying, distribution and modification follow.

GNU GENERAL PUBLIC LICENSE TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND

MODIFICATION

0. This License applies to any program or other work which contains a notice placed by the copyright

holder saying it may be distributed under the terms of this General Public License. The "Program",

below, refers to any such program or work, and a "work based on the Program" means either the

Program or any derivative work under copyright law: that is to say, a work containing the Program or a

portion of it, either verbatim or with modifications and/or translated into another language. (Hereinafter,

translation is included without limitation in the term "modification".) Each licensee is addressed as "you".

Activities other than copying, distribution and modification are not covered by this License; they are

outside its scope. The act of running the Program is not restricted, and the output from the Program is

covered only if its contents constitute a work based on the Program (independent of having been made

by running the Program). Whether that is true depends on what the Program does.

316

1. You may copy and distribute verbatim copies of the Program's source code as you receive it, in any

medium, provided that you conspicuously and appropriately publish on each copy an appropriate

absence of any warranty; and give any other recipients of the Program a copy of this License along with

the Program.

You may charge a fee for the physical act of transferring a copy, and you may at your option offer

warranty protection in exchange for a fee.

2.You may modify your copy or copies of the Program or any portion of it, thus forming a work based on

the Program, and copy and distribute such modifications or work under the terms of Section 1 above,

provided that you also meet all of these conditions:

a) You must cause the modified files to carry prominent notices stating that you changed the files and the

date of any change.

b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived

from the Program or any part thereof, to be licensed as a whole at no charge to all third parties under the

terms of this License.

c) If the modified program normally reads commands interactively when run, you must cause it, when

started running for such interactive use in the most ordinary way, to print or display an announcement

including an appropriate copyright notice and a notice that there is no warranty (or else, saying that you

provide a warranty) and that users may redistribute the program under these conditions, and telling the

user how to view a copy of this License. (Exception: if the Program itself is interactive but does not

normally print such an announcement, your work based on the Program is not required to print an

announcement.)

These requirements apply to the modified work as a whole. If identifiable sections of that work are not

derived from the Program, and can be reasonably considered independent and separate works in

themselves, then this License, and its terms, do not apply to those sections when you distribute them as

separate works. But when you distribute the same sections as part of a whole which is a work based on

the Program, the distribution of the whole must be on the terms of this License, whose permissions for

other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.

Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by

you; rather, the intent is to exercise the right to control the distribution of derivative or collective works

based on the Program.

In addition, mere aggregation of another work not based on the Program with the Program (or with a

work based on the Program) on a volume of a storage or distribution medium does not bring the other

work under the scope of this License.

3. You may copy and distribute the Program (or a work based on it, under Section 2) in object code or

executable form under the terms of Sections 1 and 2 above provided that you also do one of the

following:

317

a) Accompany it with the complete corresponding machine-readable source code, which must be

distributed under the terms of Sections 1 and 2 above on a medium customarily used for software

interchange; or,

b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no

more than your cost of physically performing source distribution, a complete machine-readable copy of

the corresponding source code, to be distributed under the terms of Sections 1 and 2 above on a

medium customarily used for software interchange; or,

c) Accompany it with the information you received as to the offer to distribute corresponding source

code. (This alternative is allowed only for noncommercial distribution and only if you received the

program in object code or executable form with such an offer, in accord with Subsection b above.)

The source code for a work means the preferred form of the work for making modifications to it. For an

executable work, complete source code means all the source code for all modules it contains, plus any

associated interface definition files, plus the scripts used to control compilation and installation of the

executable. However, as a special exception, the source code distributed need not include anything that

is normally distributed (in either source or binary form) with the major components (compiler, kernel, and

so on) of the operating system on which the executable runs, unless that component itself accompanies

the executable.

If distribution of executable or object code is made by offering access to copy from a designated place,

then offering equivalent access to copy the source code from the same place counts as distribution of

the source code, even though third parties are not compelled to copy the source along with the object

code.

4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under

this License. Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will

automatically terminate your rights under this License. However, parties who have received copies, or

rights, from you under this License will not have their licenses terminated so long as such parties remain

in full compliance.

5. You are not required to accept this License, since you have not signed it. However, nothing else

grants you permission to modify or distribute the Program or its derivative works. These actions are

prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Program

(or any work based on the Program), you indicate your acceptance of this License to do so, and all its

terms and conditions for copying, distributing or modifying the Program or works based on it.

6. Each time you redistribute the Program (or any work based on the Program), the recipient

automatically receives a license from the original licensor to copy, distribute or modify the Program

subject to these terms and conditions. You may not impose any further restrictions on the recipients'

exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties to

this License.

318

7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason

(not limited to patent issues), conditions are imposed on you (whether by court order, agreement or

otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of

this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License

and any other pertinent obligations, then as a consequence you may not distribute the Program at all.

For example, if a patent license would not permit royalty-free redistribution of the Program by all those

who receive copies directly or indirectly through you, then the only way you could satisfy both it and this

License would be to refrain entirely from distribution of the Program.

If any portion of this section is held invalid or unenforceable under any particular circumstance, the

balance of the section is intended to apply and the section as a whole is intended to apply in other

circumstances.

It is not the purpose of this section to induce you to infringe any patents or other property right claims or

to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the

free software distribution system, which is implemented by public license practices. Many people have

made generous contributions to the wide range of software distributed through that system in reliance on

consistent application of that system; it is up to the author/donor to decide if he or she is willing to

distribute software through any other system and a licensee cannot impose that choice.

This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this

License.

8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by

copyrighted interfaces, the original copyright holder who places the Program under this License may add

an explicit geographical distribution limitation excluding those countries, so that distribution is permitted

only in or among countries not thus excluded. In such case, this License incorporates the limitation as if

written in the body of this License.

9. The Free Software Foundation may publish revised and/or new versions of the General Public

License from time to time. Such new versions will be similar in spirit to the present version, but may differ

in detail to address new problems or concerns.

Each version is given a distinguishing version number. If the Program specifies a version number of this

License which applies to it and "any later version", you have the option of following the terms and

conditions either of that version or of any later version published by the Free Software Foundation. If the

Program does not specify a version number of this License, you may choose any version ever published

by the Free Software Foundation.

10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions

are different, write to the author to ask for permission. For software which is copyrighted by the Free

Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this.

Our decision will be guided by the two goals of preserving the free status of all derivatives of our free

software and of promoting the sharing and reuse of software generally.

319

NO WARRANTY

11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR

THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN

OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES

PROVIDE THE PROGRAM "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR

IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY

AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND

PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE,

YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.

12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL

ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE

THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY

GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE

OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR

DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES

OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH

HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

END OF TERMS AND CONDITIONS

How to Apply These Terms to Your New Programs

If you develop a new program, and you want it to be of the greatest possible use to the public, the best

way to achieve this is to make it free software which everyone can redistribute and change under these

terms.

To do so, attach the following notices to the program. It is safest to attach them to the start of each

source file to most effectively convey the exclusion of warranty; and each file should have at least the

"copyright" line and a pointer to where the full notice is found.

one line to give the program's name and a brief idea of what it does.

This program is free software; you can redistribute it and/or modify it under the terms of the GNU

General Public License as published by the Free Software Foundation; either version 2 of the License, or

(at your option) any later version.

This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without

even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See

the GNU General Public License for more details.

You should have received a copy of the GNU General Public License along with this program; if not,

write to the Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301

USA.

320

Also add information on how to contact you by electronic and paper mail.

If the program is interactive, make it output a short notice like this when it starts in an interactive mode:

Gnomovision version 69, Copyright (C) year name of author Gnomovision comes with ABSOLUTELY

NO WARRANTY; for details type 'show w'. This is free software, and you are welcome to redistribute it

under certain conditions; type 'show c' for details.

The hypothetical commands 'show w' and 'show c' should show the appropriate parts of the General

Public License. Of course, the commands you use may be called something other than 'show w' and

'show c'; they could even be mouse-clicks or menu items--whatever suits your program.

You should also get your employer (if you work as a programmer) or your school, if any, to sign a

"copyright disclaimer" for the program, if necessary. Here is a sample; alter the names:

Yoyodyne, Inc., hereby disclaims all copyright interest in the program 'Gnomovision' (which makes

passes at compilers) written by James Hacker.

signature of Ty Coon, 1 April 1989

Ty Coon, President of Vice

This General Public License does not permit incorporating your program into proprietary programs. If

your program is a subroutine library, you may consider it more useful to permit linking proprietary

applications with the library. If this is what you want to do, use the GNU Lesser General Public License

instead of this License.

GNU LGPL

This projector product includes the open source software programs which apply the GNU Lesser

General Public License Version 2 or later version ("LGPL Programs").

We provide the source code of the LGPL Programs until five (5) years after the discontinuation of same

model of this projector product.

If you desire to receive the source code of the LGPL Programs, please contact Epson as described in

the User's Guide.

These LGPL Programs are WITHOUT ANY WARRANTY; without even the implied warranty of

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public

License for more details.

The list of LGPL Programs is as follows and the names of author are described in the source code of the

LGPL Programs.

LGPL Programs

glibc-2.8

SDL-1.2.13

321

SDL-Image

cairo-1.10.2

podofo-0.91

wcecompat-1.2

The GNU Lesser General Public License Version 2 is as follows. You also can see the GNU Lesser

General Public License Version 2 at http://www.gnu.org/licenses/.

GNU LESSER GENERAL PUBLIC LICENSE

Version 2.1, February 1999

02110-1301 USA Everyone is permitted to copy and distribute verbatim copies of this license document,

but changing it is not allowed.

[This is the first released version of the Lesser GPL. It also counts as the successor of the GNU Library

Public License, version 2, hence the version number 2.1.]

Preamble

The licenses for most software are designed to take away your freedom to share and change it. By

contrast, the GNU General Public Licenses are intended to guarantee your freedom to share and

change free software--to make sure the software is free for all its users.

This license, the Lesser General Public License, applies to some specially designated software

packages--typically libraries--of the Free Software Foundation and other authors who decide to use it.

You can use it too, but we suggest you first think carefully about whether this license or the ordinary

General Public License is the better strategy to use in any particular case, based on the explanations

below.

When we speak of free software, we are referring to freedom of use, not price. Our General Public

Licenses are designed to make sure that you have the freedom to distribute copies of free software (and

charge for this service if you wish); that you receive source code or can get it if you want it; that you can

change the software and use pieces of it in new free programs; and that you are informed that you can

do these things.

To protect your rights, we need to make restrictions that forbid distributors to deny you these rights or to

ask you to surrender these rights. These restrictions translate to certain responsibilities for you if you

distribute copies of the library or if you modify it.

For example, if you distribute copies of the library, whether gratis or for a fee, you must give the

recipients all the rights that we gave you. You must make sure that they, too, receive or can get the

source code. If you link other code with the library, you must provide complete object files to the

322

recipients, so that they can relink them with the library after making changes to the library and

recompiling it. And you must show them these terms so they know their rights.

We protect your rights with a two-step method: (1) we copyright the library, and (2) we offer you this

license, which gives you legal permission to copy, distribute and/or modify the library.

To protect each distributor, we want to make it very clear that there is no warranty for the free library.

Also, if the library is modified by someone else and passed on, the recipients should know that what they

have is not the original version, so that the original author's reputation will not be affected by problems

that might be introduced by others.

Finally, software patents pose a constant threat to the existence of any free program. We wish to make

sure that a company cannot effectively restrict the users of a free program by obtaining a restrictive

license from a patent holder. Therefore, we insist that any patent license obtained for a version of the

library must be consistent with the full freedom of use specified in this license.

Most GNU software, including some libraries, is covered by the ordinary GNU General Public License.

This license, the GNU Lesser General Public License, applies to certain designated libraries, and is quite

different from the ordinary General Public License. We use this license for certain libraries in order to

permit linking those libraries into non-free programs.

When a program is linked with a library, whether statically or using a shared library, the combination of

the two is legally speaking a combined work, a derivative of the original library. The ordinary General

Public License therefore permits such linking only if the entire combination fits its criteria of freedom. The

Lesser General Public License permits more lax criteria for linking other code with the library.

We call this license the "Lesser" General Public License because it does Less to protect the user's

freedom than the ordinary General Public License. It also provides other free software developers Less

of an advantage over competing non-free programs. These disadvantages are the reason we use the

ordinary General Public License for many libraries. However, the Lesser license provides advantages in

certain special circumstances.

For example, on rare occasions, there may be a special need to encourage the widest possible use of a

certain library, so that it becomes a de-facto standard. To achieve this, non-free programs must be

allowed to use the library. A more frequent case is that a free library does the same job as widely used

non-free libraries. In this case, there is little to gain by limiting the free library to free software only, so we

use the Lesser General Public License.

In other cases, permission to use a particular library in non-free programs enables a greater number of

people to use a large body of free software. For example, permission to use the GNU C Library in non-

free programs enables many more people to use the whole GNU operating system, as well as its variant,

the GNU/Linux operating system.

Although the Lesser General Public License is Less protective of the users' freedom, it does ensure that

the user of a program that is linked with the Library has the freedom and the wherewithal to run that

program using a modified version of the Library.

323

The precise terms and conditions for copying, distribution and modification follow. Pay close attention to

the difference between a "work based on the library" and a "work that uses the library". The former

contains code derived from the library, whereas the latter must be combined with the library in order to

run.

GNU LESSER GENERAL PUBLIC LICENSE TERMS AND CONDITIONS FOR COPYING,

DISTRIBUTION AND MODIFICATION

0. This License Agreement applies to any software library or other program which contains a notice

placed by the copyright holder or other authorized party saying it may be distributed under the terms of

this Lesser General Public License (also called "this License"). Each licensee is addressed as "you".

A "library" means a collection of software functions and/or data prepared so as to be conveniently linked

with application programs (which use some of those functions and data) to form executables.

The "Library", below, refers to any such software library or work which has been distributed under these

terms. A "work based on the Library" means either the Library or any derivative work under copyright

law: that is to say, a work containing the Library or a portion of it, either verbatim or with modifications

and/or translated straightforwardly into another language. (Hereinafter, translation is included without

limitation in the term "modification".)

"Source code" for a work means the preferred form of the work for making modifications to it. For a

library, complete source code means all the source code for all modules it contains, plus any associated

interface definition files, plus the scripts used to control compilation and installation of the library.

Activities other than copying, distribution and modification are not covered by this License; they are

outside its scope. The act of running a program using the Library is not restricted, and output from such a

program is covered only if its contents constitute a work based on the Library (independent of the use of

the Library in a tool for writing it). Whether that is true depends on what the Library does and what the

program that uses the Library does.

1. You may copy and distribute verbatim copies of the Library's complete source code as you receive it,

in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate

absence of any warranty; and distribute a copy of this License along with the Library.

You may charge a fee for the physical act of transferring a copy, and you may at your option offer

warranty protection in exchange for a fee.

2. You may modify your copy or copies of the Library or any portion of it, thus forming a work based on

the Library, and copy and distribute such modifications or work under the terms of Section 1 above,

provided that you also meet all of these conditions:

a) The modified work must itself be a software library.

b) You must cause the files modified to carry prominent notices stating that you changed the files and the

date of any change.

324

c) You must cause the whole of the work to be licensed at no charge to all third parties under the terms

of this License.

d) If a facility in the modified Library refers to a function or a table of data to be supplied by an application

program that uses the facility, other than as an argument passed when the facility is invoked, then you

must make a good faith effort to ensure that, in the event an application does not supply such function or

table, the facility still operates, and performs whatever part of its purpose remains meaningful.

(For example, a function in a library to compute square roots has a purpose that is entirely well-defined

independent of the application. Therefore, Subsection 2d requires that any application-supplied function

or table used by this function must be optional: if the application does not supply it, the square root

function must still compute square roots.)

These requirements apply to the modified work as a whole. If identifiable sections of that work are not

derived from the Library, and can be reasonably considered independent and separate works in

themselves, then this License, and its terms, do not apply to those sections when you distribute them as

separate works. But when you distribute the same sections as part of a whole which is a work based on

the Library, the distribution of the whole must be on the terms of this License, whose permissions for

other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.

Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by

you; rather, the intent is to exercise the right to control the distribution of derivative or collective works

based on the Library.

In addition, mere aggregation of another work not based on the Library with the Library (or with a work

based on the Library) on a volume of a storage or distribution medium does not bring the other work

under the scope of this License.

3. You may opt to apply the terms of the ordinary GNU General Public License instead of this License to

a given copy of the Library. To do this, you must alter all the notices that refer to this License, so that

they refer to the ordinary GNU General Public License, version 2, instead of to this License. (If a newer

version than version 2 of the ordinary GNU General Public License has appeared, then you can specify

that version instead if you wish.) Do not make any other change in these notices.

Once this change is made in a given copy, it is irreversible for that copy, so the ordinary GNU General

Public License applies to all subsequent copies and derivative works made from that copy.

This option is useful when you wish to copy part of the code of the Library into a program that is not a

library.

4.You may copy and distribute the Library (or a portion or derivative of it, under Section 2) in object code

or executable form under the terms of Sections 1 and 2 above provided that you accompany it with the

complete corresponding machine-readable source code, which must be distributed under the terms of

Sections 1 and 2 above on a medium customarily used for software interchange.

325

If distribution of object code is made by offering access to copy from a designated place, then offering

equivalent access to copy the source code from the same place satisfies the requirement to distribute

the source code, even though third parties are not compelled to copy the source along with the object

code.

5. A program that contains no derivative of any portion of the Library, but is designed to work with the

Library by being compiled or linked with it, is called a "work that uses the Library". Such a work, in

isolation, is not a derivative work of the Library, and therefore falls outside the scope of this License.

However, linking a "work that uses the Library" with the Library creates an executable that is a derivative

of the Library (because it contains portions of the Library), rather than a "work that uses the library". The

executable is therefore covered by this License. Section 6 states terms for distribution of such

executables.

When a "work that uses the Library" uses material from a header file that is part of the Library, the object

code for the work may be a derivative work of the Library even though the source code is not. Whether

this is true is especially significant if the work can be linked without the Library, or if the work is itself a

library. The threshold for this to be true is not precisely defined by law.

If such an object file uses only numerical parameters, data structure layouts and accessors, and small

macros and small inline functions (ten lines or less in length), then the use of the object file is

unrestricted, regardless of whether it is legally a derivative work. (Executables containing this object

code plus portions of the Library will still fall under Section 6.)

Otherwise, if the work is a derivative of the Library, you may distribute the object code for the work under

the terms of Section 6. Any executables containing that work also fall under Section 6, whether or not

they are linked directly with the Library itself.

6. As an exception to the Sections above, you may also combine or link a "work that uses the Library"

with the Library to produce a work containing portions of the Library, and distribute that work under terms

of your choice, provided that the terms permit modification of the work for the customer's own use and

reverse engineering for debugging such modifications.

You must give prominent notice with each copy of the work that the Library is used in it and that the

Library and its use are covered by this License. You must supply a copy of this License. If the work

during execution displays copyright notices, you must include the copyright notice for the Library among

them, as well as a reference directing the user to the copy of this License. Also, you must do one of

these things:

a) Accompany the work with the complete corresponding machine-readable source code for the Library

including whatever changes were used in the work (which must be distributed under Sections 1 and 2

above); and, if the work is an executable linked with the Library, with the complete machine-readable

"work that uses the Library", as object code and/or source code, so that the user can modify the Library

and then relink to produce a modified executable containing the modified Library. (It is understood that

326

the user who changes the contents of definitions files in the Library will not necessarily be able to

recompile the application to use the modified definitions.)

b) Use a suitable shared library mechanism for linking with the Library. A suitable mechanism is one that

(1) uses at run time a copy of the library already present on the user's computer system, rather than

copying library functions into the executable, and (2) will operate properly with a modified version of the

library, if the user installs one, as long as the modified version is interface-compatible with the version

that the work was made with.

c) Accompany the work with a written offer, valid for at least three years, to give the same user the

materials specified in Subsection 6a, above, for a charge no more than the cost of performing this

distribution.

d) If distribution of the work is made by offering access to copy from a designated place, offer equivalent

access to copy the above specified materials from the same place.

e) Verify that the user has already received a copy of these materials or that you have already sent this

user a copy.

For an executable, the required form of the "work that uses the Library" must include any data and utility

programs needed for reproducing the executable from it. However, as a special exception, the materials

to be distributed need not include anything that is normally distributed (in either source or binary form)

with the major components (compiler, kernel, and so on) of the operating system on which the

executable runs, unless that component itself accompanies the executable.

It may happen that this requirement contradicts the license restrictions of other proprietary libraries that

do not normally accompany the operating system. Such a contradiction means you cannot use both

them and the Library together in an executable that you distribute.

7. You may place library facilities that are a work based on the Library side-by-side in a single library

together with other library facilities not covered by this License, and distribute such a combined library,

provided that the separate distribution of the work based on the Library and of the other library facilities is

otherwise permitted, and provided that you do these two things:

a) Accompany the combined library with a copy of the same work based on the Library, uncombined with

any other library facilities. This must be distributed under the terms of the Sections above.

b) Give prominent notice with the combined library of the fact that part of it is a work based on the

Library, and explaining where to find the accompanying uncombined form of the same work.

8. You may not copy, modify, sublicense, link with, or distribute the Library except as expressly provided

under this License. Any attempt otherwise to copy, modify, sublicense, link with, or distribute the Library

is void, and will automatically terminate your rights under this License. However, parties who have

received copies, or rights, from you under this License will not have their licenses terminated so long as

such parties remain in full compliance.

327

9. You are not required to accept this License, since you have not signed it. However, nothing else

grants you permission to modify or distribute the Library or its derivative works. These actions are

prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Library (or

any work based on the Library), you indicate your acceptance of this License to do so, and all its terms

and conditions for copying, distributing or modifying the Library or works based on it.

10. Each time you redistribute the Library (or any work based on the Library), the recipient automatically

receives a license from the original licensor to copy, distribute, link with or modify the Library subject to

these terms and conditions. You may not impose any further restrictions on the recipients' exercise of

the rights granted herein. You are not responsible for enforcing compliance by third parties with this

License.

11. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason

(not limited to patent issues), conditions are imposed on you (whether by court order, agreement or

otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of

this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License

and any other pertinent obligations, then as a consequence you may not distribute the Library at all. For

example, if a patent license would not permit royalty-free redistribution of the Library by all those who

receive copies directly or indirectly through you, then the only way you could satisfy both it and this

License would be to refrain entirely from distribution of the Library.

If any portion of this section is held invalid or unenforceable under any particular circumstance, the

balance of the section is intended to apply, and the section as a whole is intended to apply in other

circumstances.

It is not the purpose of this section to induce you to infringe any patents or other property right claims or

to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the

free software distribution system which is implemented by public license practices. Many people have

made generous contributions to the wide range of software distributed through that system in reliance on

consistent application of that system; it is up to the author/donor to decide if he or she is willing to

distribute software through any other system and a licensee cannot impose that choice.

This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this

License.

12. If the distribution and/or use of the Library is restricted in certain countries either by patents or by

copyrighted interfaces, the original copyright holder who places the Library under this License may add

an explicit geographical distribution limitation excluding those countries, so that distribution is permitted

only in or among countries not thus excluded. In such case, this License incorporates the limitation as if

written in the body of this License.

13. The Free Software Foundation may publish revised and/or new versions of the Lesser General

Public License from time to time. Such new versions will be similar in spirit to the present version, but

may differ in detail to address new problems or concerns.

328

Each version is given a distinguishing version number. If the Library specifies a version number of this

License which applies to it and "any later version", you have the option of following the terms and

conditions either of that version or of any later version published by the Free Software Foundation. If the

Library does not specify a license version number, you may choose any version ever published by the

Free Software Foundation.

14. If you wish to incorporate parts of the Library into other free programs whose distribution conditions

are incompatible with these, write to the author to ask for permission. For software which is copyrighted

by the Free Software Foundation, write to the Free Software Foundation; we sometimes make

exceptions for this. Our decision will be guided by the two goals of preserving the free status of all

derivatives of our free software and of promoting the sharing and reuse of software generally.

NO WARRANTY

15. BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR

THE LIBRARY, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE

STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE

LIBRARY "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED,

INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND

PERFORMANCE OF THE LIBRARY IS WITH YOU. SHOULD THE LIBRARY PROVE DEFECTIVE,

YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.

16. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL

ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE

THE LIBRARY AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY

GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE

OR INABILITY TO USE THE LIBRARY (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA

BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A

FAILURE OF THE LIBRARY TO OPERATE WITH ANY OTHER SOFTWARE), EVEN IF SUCH

HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

END OF TERMS AND CONDITIONS

How to Apply These Terms to Your New Libraries

If you develop a new library, and you want it to be of the greatest possible use to the public, we

recommend making it free software that everyone can redistribute and change. You can do so by

permitting redistribution under these terms (or, alternatively, under the terms of the ordinary General

Public License).

To apply these terms, attach the following notices to the library. It is safest to attach them to the start of

each source file to most effectively convey the exclusion of warranty; and each file should have at least

the "copyright" line and a pointer to where the full notice is found.

one line to give the library's name and a brief idea of what it does.

329

This library is free software; you can redistribute it and/or modify it under the terms of the GNU Lesser

General Public License as published by the Free Software Foundation; either version 2.1 of the License,

or (at your option) any later version.

This library is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even

the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the

GNU Lesser General Public License for more details.

You should have received a copy of the GNU Lesser General Public License along with this library; if

not, write to the Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301

USA

Also add information on how to contact you by electronic and paper mail.

You should also get your employer (if you work as a programmer) or your school, if any, to sign a

"copyright disclaimer" for the library, if necessary. Here is a sample; alter the names:

Yoyodyne, Inc., hereby disclaims all copyright interest in the library 'Frob' (a library for tweaking knobs)

written by James Random Hacker.

signature of Ty Coon, 1 April 1990

Ty Coon, President of Vice

That's all there is to it!

BSD License (Berkeley Software Distribution License)

This projector product includes the open source software program "University of California, Berkeley

License (Berkeley Software Distribution License)" which applies the terms and conditions provided by

owner of the copyright to the "BSD License".

The "BSD License" are WITHOUT ANY WARRANTY; without even the implied warranty of

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

List of BSD License programs

busybox-1.13.4

License terms of conditions of each program which are provided by owner of the copyright to the "BSD

License" are as follows.

This code is derived from software contributed to Berkeley by Kenneth Almquist.

Redistribution and use in source and binary forms, with or without modification, are permitted provided

that the following conditions are met:

330

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the

following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the

following disclaimer in the documentation and/or other materials provided with the distribution.

3. Neither the name of the University nor the names of its contributors may be used to endorse or

promote products derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS "AS IS" AND ANY

EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE

DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE FOR ANY

DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES

(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;

LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON

ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING

NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,

EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

libjpeg

This projector product includes the open source software program "libjpeg" which applies the terms and

conditions provided by owner of the copyright to the "libjpeg".

The "libjpeg" are WITHOUT ANY WARRANTY; without even the implied warranty of

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

List of libjpeg programs

libjpeg-6b

License terms of conditions of each program which are provided by owner of the copyright to the

"libjpeg" are as follows.

For conditions of distribution and use, see the accompanying README file.

This distribution contains the sixth public release of the Independent JPEG Group's free JPEG software.

You are welcome to redistribute this software and to use it for any purpose, subject to the conditions

under LEGAL ISSUES, below.

LEGAL ISSUES

============

In plain English:

1. We don't promise that this software works. (But if you find any bugs, please let us know!)

331

2. You can use this software for whatever you want. You don't have to pay us.

3. You may not pretend that you wrote this software. If you use it in a program, you must acknowledge

somewhere in your documentation that you've used the IJG code.

In legalese:

The authors make NO WARRANTY or representation, either express or implied, with respect to this

software, its quality, accuracy, merchantability, or fitness for a particular purpose. This software is

provided "AS IS", and you, its user, assume the entire risk as to its quality and accuracy.

below.

Permission is hereby granted to use, copy, modify, and distribute this software (or portions thereof) for

any purpose, without fee, subject to these conditions:

(1) If any part of the source code for this software is distributed, then this README file must be included,

with this copyright and no-warranty notice unaltered; and any additions, deletions, or changes to the

original files must be clearly indicated in accompanying documentation.

(2) If only executable code is distributed, then the accompanying documentation must state that "this

software is based in part on the work of the Independent JPEG Group".

(3) Permission for use of this software is granted only if the user accepts full responsibility for any

undesirable consequences; the authors accept NO LIABILITY for damages of any kind.

These conditions apply to any software derived from or based on the IJG code, not just to the unmodified

library. If you use our work, you ought to acknowledge us.

Permission is NOT granted for the use of any IJG author's name or company name in advertising or

publicity relating to this software or products derived from it. This software may be referred to only as

"the Independent JPEG Group's software".

We specifically permit and encourage the use of this software as the basis of commercial products,

provided that all warranty or liability claims are assumed by the product vendor.

ansi2knr.c is included in this distribution by permission of L. Peter Deutsch, sole proprietor of its

principally, that you must include source code if you redistribute it. (See the file ansi2knr.c for full details.)

However, since ansi2knr.c is not needed as part of any program generated from the IJG code, this does

not limit you more than the foregoing paragraphs do.

The Unix configuration script "configure" was produced with GNU Autoconf. It is copyright by the Free

Software Foundation but is freely distributable. The same holds for its supporting scripts (config.guess,

config.sub, ltconfig, ltmain.sh). Another support script, install-sh, is copyright by M.I.T. but is also freely

distributable.

332

It appears that the arithmetic coding option of the JPEG spec is covered by patents owned by IBM, ATT,

and Mitsubishi. Hence arithmetic coding cannot legally be used without obtaining one or more licenses.

For this reason, support for arithmetic coding has been removed from the free JPEG software. (Since

arithmetic coding provides only a marginal gain over the unpatented Huffman mode, it is unlikely that

very many implementations will support it.) So far as we are aware, there are no patent restrictions on

the remaining code.

The IJG distribution formerly included code to read and write GIF files. To avoid entanglement with the

Unisys LZW patent, GIF reading support has been removed altogether, and the GIF writer has been

simplified to produce "uncompressed GIFs". This technique does not use the LZW algorithm; the

resulting GIF files are larger than usual, but are readable by all standard GIF decoders.

We are required to state that "The Graphics Interchange Format(c) is the Copyright property of

CompuServe Incorporated. GIF(sm) is a Service Mark property of CompuServe Incorporated."

libpng

This projector product includes the open source software program "libpng" which applies the terms and

conditions provided by owner of the copyright to the "libpng".

The "libpng" are WITHOUT ANY WARRANTY; without even the implied warranty of

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

List of libpng programs

libpng-1.2.49

License terms of conditions of each program which are provided by owner of the copyright to the "libpng"

are as follows.

1995, 1996 Guy Eric Schalnat, Group 42, Inc.)

This copy of the libpng notices is provided for your convenience. In case of any discrepancy between

this copy and the notices in the file png.h that is included in the libpng distribution, the latter shall prevail.

If you modify libpng you may insert additional notices immediately following this sentence.

This code is released under the libpng license.

2009 Glenn Randers-Pehrson, and are distributed according to the same disclaimer and license as

libpng-1.2.5 with the following individual added to the list of Contributing Authors

Cosmin Truta

333

Randers-Pehrson, and are distributed according to the same disclaimer and license as libpng-1.0.6 with

the following individuals added to the list of Contributing Authors

Simon-Pierre Cadieux

Eric S. Raymond

Gilles Vollant

and with the following additions to the disclaimer:

There is no warranty against interference with your enjoyment of the library or against infringement.

There is no warranty that our efforts or the library will fulfill any of your particular purposes or needs. This

library is provided with all faults, and the entire risk of satisfactory quality, performance, accuracy, and

effort is with the user.

Randers-Pehrson, and are distributed according to the same disclaimer and license as libpng-0.96, with

the following individuals added to the list of Contributing Authors:

Tom Lane

Glenn Randers-Pehrson

Willem van Schaik

Distributed according to the same disclaimer and license as libpng-0.88, with the following individuals

added to the list of Contributing Authors:

John Bowler

Kevin Bracey

Sam Bushell

Magnus Holmgren

Greg Roelofs

Tom Tanner

Schalnat, Group 42, Inc.

For the purposes of this copyright and license, "Contributing Authors" is defined as the following set of

individuals:

Andreas Dilger

Dave Martindale

334

Guy Eric Schalnat

Paul Schmidt

Tim Wegner

The PNG Reference Library is supplied "AS IS". The Contributing Authors and Group 42, Inc. disclaim all

warranties, expressed or implied, including, without limitation, the warranties of merchantability and of

fitness for any purpose. The Contributing Authors and Group 42, Inc. assume no liability for direct,

indirect, incidental, special, exemplary, or consequential damages, which may result from the use of the

PNG Reference Library, even if advised of the possibility of such damage.

Permission is hereby granted to use, copy, modify, and distribute this source code, or portions hereof, for

any purpose, without fee, subject to the following restrictions:

1. The origin of this source code must not be misrepresented.

2. Altered versions must be plainly marked as such and must not be misrepresented as being the

original source.

3. This Copyright notice may not be removed or altered from any source or altered source distribution.

The Contributing Authors and Group 42, Inc. specifically permit, without fee, and encourage the use of

this source code as a component to supporting the PNG file format in commercial products. If you use

this source code in a product, acknowledgment is not required but would be appreciated.

A "png_get_copyright" function is available, for convenient use in "about" boxes and the like:

printf("%s",png_get_copyright(NULL));

Also, the PNG logo (in PNG format, of course) is supplied in the files "pngbar.webp" and "pngbar.jpg"

(88x31) and "pngnow.webp" (98x31).

Libpng is OSI Certified Open Source Software. OSI Certified Open Source is a certification mark of the

Open Source Initiative.

Glenn Randers-Pehrson

glennrp@users.sourceforge.net

March 29, 2012

zlib

This projector product includes the open source software program "zlib" which applies the terms and

conditions provided by owner of the copyright to the "zlib".

The "zlib" are WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY

AND FITNESS FOR A PARTICULAR PURPOSE.

List of zlib programs

335

zlib-1.1.4

zlib-1.2.3

minzip 1.01e

License terms of conditions of each program which are provided by owner of the copyright to the "zlib"

are as follows.

This software is provided 'as-is', without any express or implied warranty. In no event will the authors be

held liable for any damages arising from the use of this software.

Permission is granted to anyone to use this software for any purpose, including commercial applications,

and to alter it and redistribute it freely, subject to the following restrictions:

1. The origin of this software must not be misrepresented; you must not claim that you wrote the original

software. If you use this software in a product, an acknowledgment in the product documentation would

be appreciated but is not required.

2. Altered source versions must be plainly marked as such, and must not be misrepresented as being

the original software.

3. This notice may not be removed or altered from any source distribution.

Jean-loup Gailly

jloup@gzip.org

Mark Adler

madler@alumni.caltech.edu

If you use the zlib library in a product, we would appreciate *not* receiving lengthy legal documents to

sign. The sources are provided for free but without warranty of any kind. The library has been entirely

written by Jean-loup Gailly and Mark Adler; it does not include third-party code.

If you redistribute modified sources, we would appreciate that you include in the file ChangeLog history

information documenting your changes.

Apache License

This projector product includes the open source software program which applies the following license

terms "Apache License Version 2.0, January 2004".

List of "Apache License Programs"

mDNSResponder-107.6 (only mDNSResponderPosix is used)

336

Google Web Toolkit

GWT-Crypto 2.3.0

get-file-api

GWT-Log

DroidSansFallback

License terms "Apache License Version 2.0, January 2004" are as follows.

Apache License

Version 2.0, January 2004

http://www.apache.org/licenses/

TERMS AND CONDITIONS FOR USE, REPRODUCTION, AND DISTRIBUTION

1. Definitions.

"License" shall mean the terms and conditions for use, reproduction, and distribution as defined by

Sections 1 through 9 of this document.

"Licensor" shall mean the copyright owner or entity authorized by the copyright owner that is granting the

License.

"Legal Entity" shall mean the union of the acting entity and all other entities that control, are controlled

by, or are under common control with that entity. For the purposes of this definition, "control" means (i)

the power, direct or indirect, to cause the direction or management of such entity, whether by contract or

otherwise, or (ii) ownership of fifty percent (50%) or more of the outstanding shares, or (iii) beneficial

ownership of such entity.

"You" (or "Your") shall mean an individual or Legal Entity exercising permissions granted by this License.

"Source" form shall mean the preferred form for making modifications, including but not limited to

software source code, documentation source, and configuration files.

"Object" form shall mean any form resulting from mechanical transformation or translation of a Source

form, including but not limited to compiled object code, generated documentation, and conversions to

other media types.

"Work" shall mean the work of authorship, whether in Source or Object form, made available under the

License, as indicated by a copyright notice that is included in or attached to the work (an example is

provided in the Appendix below).

"Derivative Works" shall mean any work, whether in Source or Object form, that is based on (or derived

from) the Work and for which the editorial revisions, annotations, elaborations, or other modifications

represent, as a whole, an original work of authorship. For the purposes of this License, Derivative Works

337

shall not include works that remain separable from, or merely link (or bind by name) to the interfaces of,

the Work and Derivative Works thereof.

"Contribution" shall mean any work of authorship, including the original version of the Work and any

modifications or additions to that Work or Derivative Works thereof, that is intentionally submitted to

Licensor for inclusion in the Work by the copyright owner or by an individual or Legal Entity authorized to

submit on behalf of the copyright owner. For the purposes of this definition, "submitted" means any form

of electronic, verbal, or written communication sent to the Licensor or its representatives, including but

not limited to communication on electronic mailing lists, source code control systems, and issue tracking

systems that are managed by, or on behalf of, the Licensor for the purpose of discussing and improving

the Work, but excluding communication that is conspicuously marked or otherwise designated in writing

by the copyright owner as "Not a Contribution."

"Contributor" shall mean Licensor and any individual or Legal Entity on behalf of whom a Contribution

has been received by Licensor and subsequently incorporated within the Work.

2. Grant of Copyright License. Subject to the terms and conditions of this License, each Contributor

hereby grants to You a perpetual, worldwide, non-exclusive, no-charge, royalty-free, irrevocable

sublicense, and distribute the Work and such Derivative Works in Source or Object form.

3. Grant of Patent License. Subject to the terms and conditions of this License, each Contributor hereby

grants to You a perpetual, worldwide, non-exclusive, no-charge, royalty-free, irrevocable (except as

stated in this section) patent license to make, have made, use, offer to sell, sell, import, and otherwise

transfer the Work, where such license applies only to those patent claims licensable by such Contributor

that are necessarily infringed by their Contribution(s) alone or by combination of their Contribution(s) with

the Work to which such Contribution(s) was submitted. If You institute patent litigation against any entity

(including a cross-claim or counterclaim in a lawsuit) alleging that the Work or a Contribution

incorporated within the Work constitutes direct or contributory patent infringement, then any patent

licenses granted to You under this License for that Work shall terminate as of the date such litigation is

filed.

4. Redistribution. You may reproduce and distribute copies of the Work or Derivative Works thereof in

any medium, with or without modifications, and in Source or Object form, provided that You meet the

following conditions:

(a) You must give any other recipients of the Work or Derivative Works a copy of this License; and

(b) You must cause any modified files to carry prominent notices stating that You changed the files; and

trademark, and attribution notices from the Source form of the Work, excluding those notices that do not

pertain to any part of the Derivative Works; and

(d) If the Work includes a "NOTICE" text file as part of its distribution, then any Derivative Works that You

distribute must include a readable copy of the attribution notices contained within such NOTICE file,

338

excluding those notices that do not pertain to any part of the Derivative Works, in at least one of the

following places: within a NOTICE text file distributed as part of the Derivative Works; within the Source

form or documentation, if provided along with the Derivative Works; or, within a display generated by the

Derivative Works, if and wherever such third-party notices normally appear. The contents of the NOTICE

file are for informational purposes only and do not modify the License. You may add Your own attribution

notices within Derivative Works that You distribute, alongside or as an addendum to the NOTICE text

from the Work, provided that such additional attribution notices cannot be construed as modifying the

License.

You may add Your own copyright statement to Your modifications and may provide additional or different

license terms and conditions for use, reproduction, or distribution of Your modifications, or for any such

Derivative Works as a whole, provided Your use, reproduction, and distribution of the Work otherwise

complies with the conditions stated in this License.

5. Submission of Contributions. Unless You explicitly state otherwise, any Contribution intentionally

submitted for inclusion in the Work by You to the Licensor shall be under the terms and conditions of this

License, without any additional terms or conditions.

Notwithstanding the above, nothing herein shall supersede or modify the terms of any separate license

agreement you may have executed with Licensor regarding such Contributions.

6. Trademarks. This License does not grant permission to use the trade names, trademarks, service

marks, or product names of the Licensor, except as required for reasonable and customary use in

describing the origin of the Work and reproducing the content of the NOTICE file.

7. Disclaimer of Warranty. Unless required by applicable law or agreed to in writing, Licensor provides

the Work (and each Contributor provides its Contributions) on an "AS IS" BASIS, WITHOUT

WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied, including, without limitation,

any warranties or conditions of TITLE, NON-INFRINGEMENT, MERCHANTABILITY, or FITNESS FOR

A PARTICULAR PURPOSE. You are solely responsible for determining the appropriateness of using or

redistributing the Work and assume any risks associated with Your exercise of permissions under this

License.

8. Limitation of Liability. In no event and under no legal theory, whether in tort (including negligence),

contract, or otherwise, unless required by applicable law (such as deliberate and grossly negligent acts)

or agreed to in writing, shall any Contributor be liable to You for damages, including any direct, indirect,

special, incidental, or consequential damages of any character arising as a result of this License or out of

the use or inability to use the Work (including but not limited to damages for loss of goodwill, work

stoppage, computer failure or malfunction, or any and all other commercial damages or losses), even if

such Contributor has been advised of the possibility of such damages.

9. Accepting Warranty or Additional Liability. While redistributing the Work or Derivative Works thereof,

You may choose to offer, and charge a fee for, acceptance of support, warranty, indemnity, or other

liability obligations and/or rights consistent with this License. However, in accepting such obligations,

You may act only on Your own behalf and on Your sole responsibility, not on behalf of any other

339

Contributor, and only if You agree to indemnify, defend, and hold each Contributor harmless for any

liability incurred by, or claims asserted against, such Contributor by reason of your accepting any such

warranty or additional liability.

END OF TERMS AND CONDITIONS

APPENDIX: How to apply the Apache License to your work.

To apply the Apache License to your work, attach the following boilerplate notice, with the fields

enclosed by brackets "[]" replaced with your own identifying information. (Don't include the brackets!)

The text should be enclosed in the appropriate comment syntax for the file format. We also recommend

that a file or class name and description of purpose be included on the same "printed page" as the

Licensed under the Apache License, Version 2.0 (the "License");

you may not use this file except in compliance with the License.

You may obtain a copy of the License at

http://www.apache.org/licenses/LICENSE-2.0

Unless required by applicable law or agreed to in writing, software distributed under the License is

distributed on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either

express or implied.

See the License for the specific language governing permissions and limitations under the License.

newlib

This projector product includes the open source software program "newlib" which applies the terms and

conditions provided by owner of the copyright to the "newlib".

The "newlib" are WITHOUT ANY WARRANTY; without even the implied warranty of

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

List of newlib programs

newlib 1.17.0

License terms of conditions of each program which are provided by owner of the copyright to the "newlib"

are as follows.

The newlib subdirectory is a collection of software from several sources.

Each file may have its own copyright/license that is embedded in the source file. Unless otherwise noted

in the body of the source file(s), the following copyright notices will apply to the contents of the newlib

subdirectory:

340

(1) Red Hat Incorporated

This copyrighted material is made available to anyone wishing to use, modify, copy, or redistribute it

subject to the terms and conditions of the BSD License. This program is distributed in the hope that it will

be useful, but WITHOUT ANY WARRANTY expressed or implied, including the implied warranties of

MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. A copy of this license is available

at http://www.opensource.org/licenses. Any Red Hat trademarks that are incorporated in the source

code or documentation are not subject to the BSD License and may only be used or replicated with the

express permission of Red Hat, Inc.

(2) University of California, Berkeley

Redistribution and use in source and binary forms, with or without modification, are permitted provided

that the following conditions are met:

Redistributions of source code must retain the above copyright notice, this list of conditions and the

following disclaimer.

Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the

following disclaimer in the documentation and/or other materials provided with the distribution.

Neither the name of the University nor the names of its contributors may be used to endorse or promote

products derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"

AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE

DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE

FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL

DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR

SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER

CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR

TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF

THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

(3) David M. Gay (ATT 1991, Lucent 1998)

341

The author of this software is David M. Gay.

Permission to use, copy, modify, and distribute this software for any purpose without fee is hereby

granted, provided that this entire notice is included in all copies of any software which is or includes a

copy or modification of this software and in all copies of the supporting documentation for such software.

THIS SOFTWARE IS BEING PROVIDED "AS IS", WITHOUT ANY EXPRESS OR IMPLIED

WARRANTY. IN PARTICULAR, NEITHER THE AUTHOR NOR ATT MAKES ANY REPRESENTATION

OR WARRANTY OF ANY KIND CONCERNING THE MERCHANTABILITY OF THIS SOFTWARE OR

ITS FITNESS FOR ANY PARTICULAR PURPOSE.

-----------

The author of this software is David M. Gay.

Permission to use, copy, modify, and distribute this software and its documentation for any purpose and

without fee is hereby granted, provided that the above copyright notice appear in all copies and that both

that the copyright notice and this permission notice and warranty disclaimer appear in supporting

documentation, and that the name of Lucent or any of its entities not be used in advertising or publicity

pertaining to distribution of the software without specific, written prior permission.

LUCENT DISCLAIMS ALL WARRANTIES WITH REGARD TO THIS SOFTWARE, INCLUDING ALL

IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL LUCENT OR

ANY OF ITS ENTITIES BE LIABLE FOR ANY SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES

OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,

WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION,

ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.

(4) Advanced Micro Devices

This software is the property of Advanced Micro Devices, Inc (AMD) which specifically grants the user

the right to modify, use and distribute this software provided this notice is not removed or altered. All

other rights are reserved by AMD.

AMD MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS

SOFTWARE. IN NO EVENT SHALL AMD BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL

DAMAGES IN CONNECTION WITH OR ARISING FROM THE FURNISHING, PERFORMANCE, OR

USE OF THIS SOFTWARE.

342

So that all may benefit from your experience, please report any problems or suggestions about this

software to the 29K Technical Support Center at 800-29-29-AMD (800-292-9263) in the USA, or 0800-

89-1131 in the UK, or 0031-11-1129 in Japan, toll free. The direct dial number is 512-462-4118.

Advanced Micro Devices, Inc.

29K Support Products

Mail Stop 573

5900 E. Ben White Blvd.

Austin, TX 78741

800-292-9263

(5)

C.W. Sandmann

This file may be freely distributed as long as the author's name remains.

(6) Eric Backus

This software may be used freely so long as this copyright notice is left intact. There is no warrantee on

this software.

(7) Sun Microsystems

Developed at SunPro, a Sun Microsystems, Inc. business. Permission to use, copy, modify, and

distribute this software is freely granted, provided that this notice is preserved.

(8) Hewlett Packard

To anyone who acknowledges that this file is provided "AS IS" without any express or implied warranty:

permission to use, copy, modify, and distribute this file for any purpose is hereby granted without fee,

provided that the above copyright notice and this notice appears in all copies, and that the name of

Hewlett-Packard Company not be used in advertising or publicity pertaining to distribution of the

software without specific, written prior permission. Hewlett-Packard Company makes no representations

about the suitability of this software for any purpose.

(9) Hans-Peter Nilsson

343

Permission to use, copy, modify, and distribute this software is freely granted, provided that the above

THIS SOFTWARE IS PROVIDED "AS IS" AND WITHOUT ANY EXPRESS OR IMPLIED

WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

(11) Christopher G. Demetriou

Redistribution and use in source and binary forms, with or without modification, are permitted provided

that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the

following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the

following disclaimer in the documentation and/or other materials provided with the distribution.

3. The name of the author may not be used to endorse or promote products derived from this software

without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE AUTHOR "AS IS" AND ANY EXPRESS OR IMPLIED

WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO

EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,

EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,

PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS;

OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,

WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR

OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED

OF THE POSSIBILITY OF SUCH DAMAGE.

(12) SuperH, Inc.

This software is the property of SuperH, Inc (SuperH) which specifically grants the user the right to

modify, use and distribute this software provided this notice is not removed or altered. All other rights are

reserved by SuperH.

SUPERH MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS

SOFTWARE. IN NO EVENT SHALL SUPERH BE LIABLE FOR INDIRECT, SPECIAL, INCIDENTAL OR

CONSEQUENTIAL DAMAGES IN CONNECTION WITH OR ARISING FROM THE FURNISHING,

PERFORMANCE, OR USE OF THIS SOFTWARE.

344

So that all may benefit from your experience, please report any problems

or suggestions about this software to the SuperH Support Center via

e-mail at softwaresupport@superh.com .

SuperH, Inc.

405 River Oaks Parkway

San Jose

CA 95134

USA

(13) Royal Institute of Technology

Redistribution and use in source and binary forms, with or without modification, are permitted provided

that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the

following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the

following disclaimer in the documentation and/or other materials provided with the distribution.

3. Neither the name of KTH nor the names of its contributors may be used to endorse or promote

products derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY KTH AND ITS CONTRIBUTORS "AS IS" AND ANY EXPRESS

OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO

EVENT SHALL KTH OR ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,

INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT

LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR

PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF

LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR

OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED

OF THE POSSIBILITY OF SUCH DAMAGE.

(14) Alexey Zelkin

345

Redistribution and use in source and binary forms, with or without modification, are permitted provided

that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the

following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the

following disclaimer in the documentation and/or other materials provided with the distribution.

THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS "AS IS" AND ANY

EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE

DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY

DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES

(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;

LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON

ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING

NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,

EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

(15) Andrey A. Chernov

Redistribution and use in source and binary forms, with or without modification, are permitted provided

that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the

following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the

following disclaimer in the documentation and/or other materials provided with the distribution.

THIS SOFTWARE IS PROVIDED BY THE AUTHOR "AS IS" AND ANY EXPRESS OR IMPLIED

WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO

EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,

INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT

LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR

PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF

LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR

OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED

OF THE POSSIBILITY OF SUCH DAMAGE.

(16) FreeBSD

346