Table of Contents
- Organization of the Guide and Notations in the Guide
- Contents
- Introduction
- Preparing
- Basic Operations
- Projecting Images
- Adjusting the Projected Image
- Adjusting the Image
- Useful Functions
- Using the Projector on a Network
- Configuration Menu
- Troubleshooting
- Maintenance
- Appendix
- Index
Epson EH-LS500B User Manual
Displayed below is the user manual for EH-LS500B by Epson which is a product in the Data Projectors category. This manual has pages.
Related Manuals
User's Guide
Organization of the Guide and Notations in the Guide
1
Using Each Guide
The guides for this projector are organized as shown below.
Safety Instructions/Support and Service Guide
Contains information on using the projector safely, as well as a support and service guide,
troubleshooting check lists, and so on. Make sure you read this guide before using the pro-
jector.
User's Guide (this guide)
Contains information on setting up and basic operations before using the projector, using
the Configuration menu, and handling problems and performing routine maintenance.
Quick Start Guide
Contains information on the procedures for setting up the projector. Read this first.
Organization of the Guide and Notations in the Guide
2
Notations Used in This Guide
Safety Indications
The documentation and the projector use graphical symbols to show how to use the projector safely.
The following shows the symbols and their meanings. Please understand and respect these caution symbols
in order to avoid injury to persons or property.
Warning
This symbol indicates information that, if ignored, could possibly result in personal injury or even death
due to incorrect handling.
Caution
This symbol indicates information that, if ignored, could possibly result in personal injury or physical
damage due to incorrect handling.
General Information Indications
Attention
Indicates procedures which may result in damage or malfunctions to occur.
c
Indicates additional information and points which may be useful to know regarding a topic.
sIndicates a page where detailed information regarding a topic can be found.
Menu Name Indicates Configuration menu items.
Example: Image - Color Mode
[Hardware
Names]
Indicates the buttons on the remote control or the control panel.
Example: [Menu] button
About the Use of "This Product" or "This Projector"
As well as the main projector unit, supplied items or optional extras may be referred to using the phrase "this
product" or "this projector".
Contents
3
Organization of the Guide and
Notations in the Guide
Using Each Guide ..................... 1
Notations Used in This Guide ........... 2
Safety Indications.......................2
General Information Indications .............2
About the Use of "This Product" or "This Projector"
..................................... 2
Introduction
Projector Features .................... 6
Project Large Images Even when Near a Wall
..................................... 6
Project Images from Mobile Devices ..........6
Other Useful Functions .................... 6
Part Names and Functions ............. 7
Front/Top ............................. 7
Rear/Top .............................. 8
Connector Ports .........................9
Base ................................ 10
Control Panel .......................... 11
Remote Control ........................ 12
Preparing
Installing ............................ 15
Projected Image and Position of Projector.....15
Installing in parallel with the screen ........15
Installing the projector horizontally by
adjusting the height of either side ......... 16
Screen Size and Projection Distance.........17
Connecting a Device ................. 18
Connecting a Streaming Media Player........ 18
Connecting Video Equipment ..............19
Connecting a Computer .................. 20
Connecting to the LAN Port...............20
Attaching the Wireless LAN Unit............20
Connecting External Speakers .............. 21
Connecting an ARC Compatible AV System....21
Preparing the Remote Control ........ 22
Installing the Remote Control Batteries.......22
Remote Control Operating Range ...........23
Operating range (left to right) ............23
Operating range (top to bottom) .......... 23
Basic Operations
Projecting Images ................... 24
Turning On the Projector.................24
If the target image is not projected . . . . . . . . 25
Using the Home Screen .................. 26
Turning Off ...........................27
Adjusting the Projected Image . . . . . . . . 28
Adjusting the Focus ..................... 28
Adjusting the Projection Size (Adjust Zoom)
.................................... 28
Adjusting the Position of the Image (Image
Shift) ................................ 29
Correcting Vertical Distortion in the Image ..... 29
Correcting Keystone Distortion ............. 30
Correct using the Keystone buttons ........ 30
Correcting with Quick Corner............ 31
Adjusting the Volume .................... 32
Hiding the Image and Muting the Audio
Temporarily (A/V Mute) .................. 32
Adjusting the Image
Adjusting the Image ................. 33
Selecting the Projection Quality (Color Mode)
.................................... 33
Switching the Screen Between Full and Zoom
(Aspect).............................33
Adjusting the Sharpness .................. 35
Adjusting Image Resolution (Image
Enhancement) ......................... 36
Adjusting the Luminance for Images .........37
Setting Frame Interpolation............... 37
Setting the Image Processing Speed .........38
Adjusting the Color .................. 39
Adjusting the Color Temp.................39
Adjusting the RGB (Offset and Gain).........39
Adjusting Hue, Saturation, and Brightness . . . . . 40
Adjusting the Gamma ...................41
Contents
4
Select and adjust the correction value . . . . . . 41
Adjust using the gamma adjustment graph
.................................. 42
Viewing the Image at the Saved Image
Quality (Memory Function) . . . . . . . . . . . 43
Saving a Memory .......................43
Loading, Deleting, and Renaming a Memory
.................................... 44
Useful Functions
Enjoying 3D Images .................. 45
Preparing to View 3D Images .............. 45
If the 3D image cannot be viewed .........45
Using 3D Glasses ....................... 46
Warnings Regarding Viewing 3D Images......46
Using the HDMI Link Function ........ 48
HDMI Link Function ..................... 48
HDMI Link Settings ...................... 48
Connecting ........................... 49
Using the Projector on a Network
Projecting Using Wired LAN .......... 50
Selecting Wired Network Settings ...........50
Projecting Using Wireless LAN ........ 52
Selecting Wireless Network Settings Manually
.................................... 52
Selecting the Computer's Wireless LAN Settings
.................................... 55
Selecting wireless network settings in
Windows ........................... 55
Selecting wireless network settings in OS X
.................................. 55
Setting Up Wireless Network Security . . . . . . . . 55
Projecting in Epson iProjection (iOS/Android)
.................................... 56
Operating using a smartphone (remote
control function) .....................57
Configuration Menu
Configuration Menu Functions ........ 59
Configuration Menu Operations ............ 59
Configuration Menu Table................60
Image menu ........................60
Signal menu ........................ 62
Settings menu ....................... 63
Extended menu ...................... 65
Network menu ....................... 68
Info menu .......................... 72
Reset menu ......................... 72
Troubleshooting
Problem Solving . .................... 73
Handling Problems .....................73
Reading the Indicators ................... 73
Indicator status during an error/warning....74
Indicator status during normal operation . . . . 75
When the Indicators Provide No Help........76
Check the problem .................... 76
Problems relating to images ............. 77
Noise problems ...................... 80
Problems when projection starts ..........80
Problems with the remote control ......... 81
Problems with the control panel .......... 81
Problems with 3D .................... 82
Problems with HDMI ..................82
Problems with a streaming media player . . . . 83
Network problems .................... 83
About Event ID ........................ 85
Maintenance
Maintenance ........................ 86
Cleaning the Parts ...................... 86
Cleaning the air filter .................. 86
Cleaning the main unit ................. 88
Cleaning the lens ..................... 88
Replacement Periods for Consumables.......88
Air filter replacement period ............. 88
Replacing Consumables .................. 88
Replacing the air filter .................88
Panel Alignment ..................... 90
Color Uniformity ..................... 92
About PJLink ........................ 94
Contents
5
Appendix
Optional Accessories and
Consumables ........................ 95
Optional Items ......................... 95
Consumables .......................... 95
Supported Resolutions ............... 96
PC .................................. 96
Unique Aspect ......................... 96
SD ................................. 96
HD ................................. 97
4K .................................. 97
3D ................................. 98
Specifications ...................... 101
EH-LS500W Android TV
™
edition/EH-LS500B
Android TVTM edition .................. 101
Appearance ........................ 104
List of Safety Symbols ............... 105
Safety Instructions for Laser Products
.................................... 107
Laser Warning Labels ................... 108
Glossary ........................... 109
General Notes ...................... 110
General Notice ........................ 111
Introduction
6
Projector Features
Project Large Images Even when Near a Wall
Take advantage of the projector's ultra-short
throw lens to enjoy the full force of a projected
image up on your wall instead of using a TV.
s p.15
Project Images from Mobile Devices
By using Epson iProjection, you can wirelessly connect the pro-
jector to smartphones and tablets. You can download Epson
iProjection for free from the App Store or from Google Play.
s p.56
Other Useful Functions
In addition, the following useful functions are provided.
•Playing audio through the internal speaker. This allows you to enjoy audio without an external speaker.
•Operate by remote control from a smartphone. By using Epson iProjection, you can operate the projector from a
smartphone or tablet. s p.57
Introduction
7
Part Names and Functions
Front/Top
Name Function
aFront cover
Remove the cover when connecting a streaming media player and when operat-
ing the control panel and focus lever.
bSpeaker
The projector's built-in speaker. Outputs audio.
cControl panel
Operates the projector. s p.11
dFocus lever
Adjusts the image focus. s p.28
eStorage space cover
Remove the cover when connecting a streaming media player. s p.18
fAir filter cover
When cleaning or replacing the air filter, open this cover and remove the air filter.
s p.86, p.88
Air intake vent
Intake vent for air used to cool the projector internally.
gStandby button
(Standby indicator)
Turns the projector on or off. s p.24
Lit when the projector is on. Shows the projector's status through a combination
of other indicators lit and flashing. s p.73
hIndicators
Shows the projector's status through a combination of indicators lit and flashing.
s p.73
iRemote receiver
Receives signals from the remote control. s p.23
Introduction
8
c
When the Illumination function is set to Off, all indicators are off under normal projection conditions.
s
Extended - Operation - Illumination p.65
Rear/Top
Name Function
aLens
Images are projected from here.
bSecurity cable sec-
tion
Secure a commercially available anti-theft wire lock through this section.
cPower inlet
Connect the power cord.
dSecurity slot ( )
The security slot compatible with the MicroSaver security system manufactured
by Kensington. For more details, visit the homepage of Kensington at http://
www.kensington.com/.
eAir exhaust vent
Exhaust vent for air used to cool the projector internally.
Caution
While projecting, do not put your face or hands near the air exhaust vent,
and do not place objects that may become warped or damaged by heat near
the vent. Hot air from the air exhaust vent could cause burns, warping, or
accidents to occur.
fRemote receiver
Receives signals from the remote control. s p.23
Introduction
9
Connector Ports
Rear
Front
Menu Esc
Home Source
Focus
DC Out (2.0A)
HDMI 3
Name Function
aLAN port
Connects a LAN cable to connect to a network. s p.20
bHDMI1 port
Connects HDMI compatible video equipment and computers. s p.19
cHDMI2 (ARC) port
Connects HDMI compatible video equipment and computers. s p.19
You can also output audio by connecting an ARC compatible AV amplifier.
s p.21
dService port
Service port. This is not normally used.
eUSB-A port
Connects the optional Wireless LAN unit. It is also used when updating the
firmware. s p.20
fRS-232C port
When controlling the projector, connect the projector to a computer with an
RS-232C cable. This port is for control use and should not normally be
used. s p.101
gAudio Out port
Outputs audio during playback to external speakers. s p.21
hCable holder
Pass a commercially available cable tie through here to secure the cables.
iHDMI3 port
Inputs signals from a streaming media player. s p.18
jDC Out (2.0A) power sup-
ply port
Provides power to a streaming media player. s p.18
Introduction
10
Base
Name Function
aFront adjustable foot
When the projector is set up on a table, extend the foot to correct vertical distortion
in the image. s p.29
bAir intake vent
Takes in air to cool the projector internally.
cAir intake vent
Takes in air to cool the streaming media player.
dAir exhaust vent
Air exhaust vent to cool the streaming media player.
eRear foot
Supports the projector when it is set up on a table.
Caution
Place the projector on a flat surface such as a table to project images. Do not attach a commercially available
mount and so on to the screw hole at the bottom. If this projector is installed on a wall or ceiling using this
screw hole, it could fall and cause damage or injury to occur.
Introduction
11
Control Panel
Name Function
a[Menu] button
Displays and closes the Configuration menu.
On the Configuration menu, you can make adjustments and settings for Sig-
nal, Image, and so on. s p.59
b[Enter] button
When a menu is displayed, it confirms the current item and moves to the next
level. s p.59
c[Home] button
Displays or closes the Home screen. s p.26
dVolume (Left/Right)
buttons
•
Adjusts the volume. s p.32
•
Selects menu items or adjustment values while displaying the projector's menu.
s p.59
•
When the Keystone screen is displayed, you can adjust horizontal distortion in
the projected image. s p.30
e[Source] button
Changes to the image from each input port. s p.25
f[Esc] button
Returns to the previous menu level when a menu is displayed. s p.59
gKeystone (Up/Down)
buttons
•
Selects menu items or adjustment values while displaying the projector's
menu. s p.59
•
Adjusts keystone distortion in projected images. s p.30
Introduction
12
Remote Control
Projector remote control
This remote control allows you to operate the projector and the streaming media player supplied (ELPAP12).
Unless stated otherwise, this guide describes operations for the projector remote control.
Name Function
aStandby button
Turns the projector on or off. s p.24
bEsc button
Closes the current function. Press when a menu is displayed to return to the
previous menu level. s p.59
cUp/Down/Left/Right
buttons
Selects menu items and adjustment values. s p.59
d[Enter] button
When a menu is displayed, it confirms the current item and moves to the next
level. s p.59
eMenu button
Displays and closes the Configuration menu.
On the Configuration menu, you can make adjustments and settings for Signal,
Image, and so on. s p.59
fVolume buttons
Adjusts the volume. s p.32
gPlayback control but-
tons
Operates a streaming media player and video devices compliant with the HDMI
CEC standard. s p.48
Introduction
13
Name Function
hKeystone button
Corrects distortion in the image. s p.30
iMic button
Allows you to operate Android TV
TM
using voice commands. When you press
this button, the microphone on the remote control starts listening for voice
commands.
jSource button
Changes to the image from each input port.
kHome button
Displays or closes the Android TV
TM
home screen.
lApps button
Displays a list of apps for Android TV
TM
.
mYouTube button
Opens the YouTube app.
nA/V Mute button
Temporarily hides or shows the image and audio. s p.32
oIndicator
Turns on while operating the remote control.
pMicrophone section
This detects voice commands when you press the Mic button.
qRemote control light
emitting area
Outputs remote control signals.
Remote control for Android TVTM
This remote control allows you to operate the streaming media player supplied (ELPAP12).
Introduction
14
Name Function
aStandby button
Turns the streaming media player supplied on or off.
bUp/Down/Left/Right
buttons
Selects the Android TV
TM
menu items.
cEnter button
Confirms the current Android TV
TM
menu item and moves to the next level.
dEsc button
Press while Android TV
TM
is displayed to return to the previous menu level.
eVolume buttons
Adjusts the volume for the streaming media player supplied.
fYouTube button
Opens the YouTube app.
gNetflix button
Opens the Netflix app.
hGoogle Play button
Connects to Google Play.
iHome button
Displays the Android TV
TM
home screen.
jApps button
Displays a list of apps for Android TV
TM
.
kIndicator
Turns on while operating the remote control.
lMic button
Allows you to operate Android TV
TM
using voice commands. When you press
this button, the microphone on the remote control starts listening for voice
commands.
mMicrophone section
This detects voice commands when you press the Mic button.
nRemote control light
emitting area
Outputs remote control signals.
Preparing
15
Installing
Projected Image and Position of Projector
Install the projector on a table in your living room or on a low shelf to project images.
Follow the steps below to install the projector.
Installing in parallel with the screen
If the projector is installed at an angle to the screen, keystone distortion occurs in the projected image.
Adjust the projector's position so that it is installed in parallel with the screen.
c
If the projector cannot be installed directly in front of the screen, adjust the position of the projected
image.
s
p.28
Preparing
16
Installing the projector horizontally by adjusting the height of either side
If the projector is tilted, the projected image is also tilted.
Install the projector horizontally so that both sides are at the same height.
Warning
•Do not set up the projector in locations exposed to humidity or dust, or in locations exposed to oil smoke or
steam such as on a kitchen counter, in the kitchen, or near a humidifier. Doing so could cause fire or electric
shock.
•Do not install in locations where salt damage could occur, or in locations subject to corrosive gas such as
sulphuric gas from hot springs. Otherwise, corrosion could cause the projector to fall. It could also cause the
projector to malfunction.
•Do not install it on an unstable shelf or in a place out of load range. Otherwise, it could fall or topple causing
an accident and injury.
•When installing the projector in a high position such as on a shelf, take measures against falling by using
wires or belts to ensure safety in an emergency such as an earthquake, and to prevent accidents. If it is not
installed correctly, it could fall causing an accident and injury.
•Do not block the air intake vent and air exhaust vent of the projector. Blocking its air intake vent and air
exhaust vent may trap heat inside causing fire.
•Do not place a cloth or any paper under the projector. The cloth or paper could be sucked up by the Air intake
vent on the bottom of the projector during projection causing the internal temperature to rise which could
start a fire.
Attention
•Do not use the projector installed vertically. Doing so could cause a malfunction.
•We recommend cleaning the air filter every 20,000 hours. Clean it more often if the environment is particularly
dusty. s p.86
Preparing
17
Screen Size and Projection Distance
Use the table below to setup the projector at the optimum position from the screen. The values given here
are for your reference only.
A
B
C
D23.3cm
E
A : Projection distance
B : Distance from the projector to the bottom of the screen
C : Distance from the projector to the top of the screen
D : Distance from the center of the lens to the back of the projector
E : Size of the projected image
Unit: cm
16:9 Screen Size A B C
E W x H Minimum (Wide) to Maximum
(Tele)
Minimum (Wide) Minimum (Wide)
70" 155 x 87 43 - 59 12 99
80" 177 x 100 49 - 67 14 114
90" 199 x 112 56 - 76 16 128
100" 221 x 125 62
*
17 142
110" 244 x 137 69
*
19 156
120" 266 x 149 75
*
21 170
130" 288 x 162 82
*
23 185
*Projecting using Wide (maximum zoom)
Preparing
18
Connecting a Device
Attention
•Make cable connections before connecting to a power outlet.
•Check the shape of the cable's connector and the shape of the port, and then connect. If you force a connector
of a different shape into the port, it could cause damage and a malfunction to occur.
Connecting a Streaming Media Player
To project images from a streaming media player, connect them using the HDMI extension cable and the
USB power cable supplied.
DC Out (2.0A)
HDMI 3
Attention
The streaming media player supplied is dedicated to this projector. Depending on the video equipment
you are connecting, it may not work correctly.
c
If the streaming media player supplied is sent for repairs, it may be reset when it is returned. Make
sure you save any account information for your online services before sending it for repairs.
a
Remove the front cover.
b
Remove the storage space cover.
c
Connect the HDMI extension cable
supplied to the HDMI3 port.
Preparing
19
d
Connect the USB power cable
supplied to the DC Out (2.0A) power
supply port.
e
Connect the streaming media player
to the HDMI extension cable.
f
Connect the USB power cable to the
USB port (type B) on the streaming
media player.
g
Place the streaming media player in
the storage space.
Arrange the cables as shown in the
following diagram.
h
Replace the storage space cover.
Attention
Make sure the cables are not caught by
the cover. You cannot close the cover if
it catches on the cables.
i
Replace the front cover.
c
You need to pair the streaming
media player supplied with the
remote control when it is turned
on for the first time. Follow the
on-screen instructions to pair the
device.
s
p.22
Connecting Video Equipment
To project images from DVD/Blu-ray players, connect to the projector using an HDMI cable (commercially
available).
Preparing
20
c
•To display signals in the 18 Gbps transmission band, such as 4k60p/4:4:4, use a premium HDMI cable.
If you use a cable that does not support it, images may not be displayed properly. If you experience
any trouble displaying images at 18 Gbps, change the EDID setting to Normal. s Signal - Advanced -
EDID p.62
•You can also connect your AV system to enjoy the audio from connected equipment.
Connecting a Computer
To project images from a computer, connect to the projector using an HDMI cable (commercially available).
Connecting to the LAN Port
Connect to a network router, a hub, and so on, with a 100BASE-TX or 10BASE-T LAN cable. You can operate
the projector or check its status over a network from a computer or a smart device.
c
To prevent malfunctions, use a category 5 or higher shielded LAN cable.
Attaching the Wireless LAN Unit
When using the wireless LAN function, connect the optional Wireless LAN unit (ELPAP10) to the USB-A port.
You can use one of the following methods to project over wireless LAN. For more details, see the download
page.
Preparing
21
•Projecting four screens simultaneously
When using Epson iProjection (Windows/Mac), you can display up to four separate screens from the projector from
up to 50 computers connected to the network.
You can download Epson iProjection (Windows/Mac) from the following Web site.
https://www.epson.com
•Projecting images from a mobile terminal via a network
By installing Epson iProjection (iOS/Android) on a smartphone or tablet, you can wirelessly project data on your
device. s p.56
c
•When not using the wireless LAN function with the Wireless LAN unit kept inserted, set Wireless LAN
Power to Off. This can prevent unauthorized access from outsiders. s p.68
•When using Epson iProjection in Quick connection mode, we recommend making security settings.
s p.70
Connecting External Speakers
To output audio from external speakers, connect the speakers to the projector's Audio Out port with a
commercially available audio cable.
c
•To output audio from external speakers, set Audio Out Device to Projector. s Settings - HDMI
Link - Audio Out Device p.63
•When an AV system is not connected to the projector, audio is output from the external speakers, even
if Audio Out Device is set to AV System.
Connecting an ARC Compatible AV System
To output audio from an ARC compatible AV System, use an HDMI cable (commercially available) to connect
the AV System to the HDMI2 (ARC) port on the projector.
AVアンプ
c
Make the following settings when outputting audio from an ARC compatible AV System.
•Set the Audio Out Device to AV System. s Settings - HDMI Link - Audio Out Device p.63
•When the AV System is connected to the projector, set HDMI Link to On. s Settings - HDMI
Link p.63
Preparing
22
Preparing the Remote Control
Installing the Remote Control Batteries
Attention
•Check the positions of the (+) and (-) marks inside the battery holder to ensure the batteries are inserted the
correct way.
•You cannot use other batteries except for AAA size manganese or alkaline.
a
Remove the battery cover.
While pushing the battery compartment
cover catch, lift the cover up.
b
Replace the old batteries with new
batteries.
Check the polarity of the batteries (+) and
(-) before installing.
c
Reattach the battery cover.
Press the cover until it clicks into place.
c
If delays in the responsiveness of
the remote control occur or if it
does not operate, it probably
means that the batteries are
becoming flat. Replace with two
new batteries (AAA size
manganese or alkaline batteries).
d
You need to pair the projector's
remote control to the streaming
media player supplied to operate it
with the remote control. To perform
pairing, follow the on-screen
instructions and hold down the home
button and the [Enter] button on the
remote control at the same time for
approximately three seconds.
c
•If the projector’s HDMI Link is set
to Off, set it to On. s p.48
•The remote control indicator
flashes while pairing.
Preparing
23
Remote Control Operating Range
Operating range (left to right)
30°
30°
6m
55°
55°
55°
55°
55°
55°
6m
Operating range (top to bottom)
6m
6m
15°
60°
60°
Basic Operations
24
Projecting Images
Turning On the Projector
a
Connect the equipment to the
projector.
b
Connect using the power cord
supplied.
c
Remove the lens cap.
Attention
If the projector is turned on while the lens
cap is attached, the lens cap becomes
hot due to the light from the projector.
Make sure you remove the cap before
turning on the projector.
d
Press the standby button on the
remote control or on top of the
projector to turn it on.
Remote control Top of projector
The projector's status indicator flashes blue
as the projector warms up. Once the
projector is warmed up, the standby
indicator and the status indicator turn blue.
c
•When Direct Power On is set to
On, you can start projecting by
simply connecting the power
cord to the projector without
having to press any buttons.
s Extended - Operation -
Direct Power On p.65
•If you turn on Quick Startup from
the Extended menu, the
projector will be ready to project
in a just a few seconds the next
time it is turned on.
s Extended - Operation -
Quick Startup p.65
e
Turn on the connected equipment.
Basic Operations
25
Warning
•Do not look into the lens during projection. The powerful light emitted could cause damage to eyesight. Pay
close attention to how your child behaves.
•When using the remote control to turn it on while you are away from the projector, make sure no one is
looking into the lens.
•Do not stand in front of the lens during projection. Clothes could be damaged due to the high temperature.
c
•This projector provides a Child Lock function to prevent children from accidentally turning the power
on and a Control Panel Lock function to prevent accidental operations and so on. s Settings - Lock
Setting - Child Lock/Control Panel Lock p.63
•When using at an altitude of 1500 m or more, set High Altitude Mode to On. s Extended - Operation -
High Altitude Mode p.65
If the target image is not projected
If the image is not projected, you can change the source using one of the following methods.
Remote control Control panel
Press the source button and select the target port. Press the [Source] button and select the target port.
c
If you press the [Home] button on the control panel, you can also make settings from the Home
screen.
s
p.26
Basic Operations
26
Using the Home Screen
The Home screen feature allows you to easily select an image source and access useful functions.
Press the [Home] button on the control panel to display the Home screen.
Under the following conditions, the Home screen is displayed automatically when the projector is turned on.
•Home Screen Auto Disp. is set to On. s Extended - Home Screen - Home Screen Auto Disp. p.65
•There are no signals from any sources.
a
Selects the source you want to project.
b
Displays the Connection Guide.
c
Displays the Configuration menu. s p.59
d
Performs menu options assigned to Custom Function 1 and Custom Function 2 on the Home Screen.
s Extended - Home Screen p.65
e
Sets the brightness for the light source. s Image - Light Output p.60
f
Selects the Color Mode. s p.33 s Image - Color Mode p.60
c
The Home screen disappears after 10 minutes of inactivity.
Basic Operations
27
Turning Off
a
Turn off the connected equipment.
b
Press the standby button on the
remote control or on top of the
projector.
Remote control Top of projector
A confirmation message is displayed.
c
Press the standby button again.
The status indicator flashes and the
projector begins to cool down.
c
When Standby Confirmation is
set to Off, you can turn off the
projector by pressing the button
on the remote control once.
s
Extended - Display - Standby
Confirmation p.65
d
Wait until cool-down is complete.
When cool-down is complete, the status
indicator stops flashing.
e
Disconnect the power cord.
c
•If the power cord is connected,
some electricity is consumed
even if no operations are made.
•When connecting the power cord
again, wait a sufficient time
interval.
f
Attach the lens cap.
c
When USB Power in Standby is set to On, power is supplied to the streaming media player even
when the projector is in standby mode (power off); this helps to speed up turning on the streaming
media player.
s
Extended - Operation - USB Power in Standby p.65
Basic Operations
28
Adjusting the Projected Image
c
Since images are unstable immediately after the projector is turned on, before you make focus, zoom,
or lens shift settings, we recommend waiting 20 minutes or more after starting to project the images.
Adjusting the Focus
Adjust the focus by moving the focus lever up or down.
Adjusting the Projection Size (Adjust Zoom)
The zoom function adjusts the size of the projected image.
a
Press the [Menu] button to display
menus in the order Settings - Zoom.
Remote control Control panel
b
Use the left and right buttons to make
adjustments.
c
Press the [Menu] button to exit the
menu.
Basic Operations
29
Adjusting the Position of the Image (Image Shift)
You can adjust the position of the projected image without having to move the projector.
s
Settings -
Image Shift p.63
a
Press the [Menu] button to display
menus in the order Settings - Image
Shift.
Remote control Control panel
b
Press the up/down/left/right buttons
to adjust the position of the image.
c
Press the [Menu] button to exit the
menu.
c
•Use zoom to adjust the size of the image, and then adjust the projection position by using Image
Shift. You cannot adjust the projection position when the zoom is set to maximum wide.
•Images are not stable immediately after the projector is turned on. Wait for at least 20 minutes after
you start projecting to adjust the projection position.
•The setting for Image Shift is stored even when the projector is turned off. If you change the projector's
installation position or angle, make adjustments again.
Correcting Vertical Distortion in the Image
If the projected image is distorted vertically, adjust the front foot so that the image and the screen are at the
same angle.
Retract the foot
Extend the foot
Basic Operations
30
Correcting Keystone Distortion
If you place the projector at an angle to the screen, or tilt it up or down, or off to the side, you may need to
correct the distortion in the image.
You can correct it by using one of the following two methods.
•Correct the vertical and horizontal distortion s p.30
•Correct the corners of the projected image individually s p.31
Correct using the Keystone buttons
You can use the up/down/left/right buttons on the control panel or the remote control to correct vertical
and horizontal keystone distortion.
Press the up/down buttons on the control panel or the keystone button on the remote control to display the
V-Keystone/H-Keystone gauges.
When the gauges are displayed, press the up and down buttons to perform vertical correction, and press the
left and right buttons to perform horizontal correction.
When the top or bottom is too wide
When the left or right is too wide
c
•When you correct keystone distortion, the projected image may be reduced. Increase the projection
distance to fit the projected image to the screen size.
•You can also set H/V-Keystone from the Configuration menu. s Settings - Keystone - H/V-
Keystone p.63
•You can make effective corrections within a projection angle of 3° up, down, left, and right.
•You can adjust the volume by pressing the left/right buttons on the control panel when the V-
Keystone/H-Keystone gauges are not displayed. s p.32
Basic Operations
31
Correcting with Quick Corner
You can use the projector's Quick Corner setting to correct the shape and size of an image that is unevenly
rectangular.
a
Press the [Menu] button to display
menus in the order Settings -
Keystone.
Remote control Control panel
b
Use the up and down buttons to select
Quick Corner, and then press the
[Enter] button. Press the [Enter]
button again if necessary.
The area selection screen is displayed.
c
Use the up/down/left/right buttons to
select the corner of the image you
want to adjust. Then press the [Enter]
button.
c
To reset the Quick Corner
corrections, hold down the [Esc]
button for about two seconds
while the area selection screen is
displayed, and then select Yes.
d
Press the up/down/left/right buttons
to adjust the shape of the image as
necessary. Press the [Enter] button to
return to the area selection screen.
c
If you see this screen, you cannot
adjust the shape any further in the
direction indicated by the gray
triangle.
e
Repeat steps 3 and 4 as needed to
adjust any remaining corners.
f
When you are finished, press the
[Esc] button.
c
After executing Quick Corner, the
Keystone setting is now set to
Quick Corner in the projector's
Settings menu. When you press
the up/down buttons on the
control panel or the keystone
button on the remote control, the
area selection screen is displayed.
Basic Operations
32
Adjusting the Volume
You can adjust the volume by using the volume buttons on the remote control or on the control panel.
Remote control Control panel
c
•You can also adjust the volume from the Configuration menu. s Settings - Volume p.63
•When an AV System is connected to the projector and you want to adjust the volume for the AV system,
set HDMI Link to On and Audio Out Device to AV System. s Settings - HDMI Link p.63
•If you have used the remote control for Android TV
TM
to mute the volume on your streaming media
player, you will not be able to turn it up using the projector remote control. Increase the volume using
the remote control for Android TV
TM
before you make adjustments.
Caution
Do not start at high volume.
A sudden excessive volume may cause loss of hearing. Always lower the volume before powering off, so
that you can power on and then gradually increase the volume.
Hiding the Image and Muting the Audio Temporarily (A/V Mute)
Press the A/V mute button on the remote control to show or hide the image. The audio is also muted or played.
c
•For movies, the image and audio continue to play even during A/V Mute. You cannot resume projection
from the point that you muted the video and audio using the A/V mute button.
•When outputting audio from an AV system and you want to adjust the volume for the AV system, set
HDMI Link to On and Audio Out Device to AV System. s Settings - HDMI Link p.63
Adjusting the Image
33
Adjusting the Image
Selecting the Projection Quality (Color Mode)
You can obtain the optimum image quality to suit your surroundings when projecting. The brightness of the
image varies depending on the mode selected.
a
Press the [Menu] button to display menus in the order Image - Color Mode.
Remote control Control panel
c
If you press the [Home] button on the control panel, you can also make settings from the
Home screen.
s
p.26
b
Use the up and down buttons to select a mode, and then press the [Enter] button to confirm
the selection.
Mode Application
Dynamic
This is the brightest mode. Best for prioritizing brightness.
Bright Cinema
Best for projecting vivid images.
Cinema
Best for enjoying content such as movies.
Game
Best for enjoying content such as video games.
Switching the Screen Between Full and Zoom (Aspect)
You can change the input signal's type, aspect ratio, and resolution to match the Aspect of the projected
image.
The available settings vary depending on the image signal currently being projected.
c
Note that using the aspect ratio function of the projector to reduce, enlarge, or split the projected
image for commercial purposes or for public viewing may infringe upon the rights of the copyright
holder of that image based on copyright law.
Adjusting the Image
34
a
Press the [Menu] button to display
menus in the order Signal - Aspect.
Remote control Control panel
b
Use the up and down buttons to select
the aspect mode, and then press the
[Enter] button to confirm the
selection.
c
You cannot switch the Aspect when the Source is LAN. Also, when the Source is HDMI1/HDMI2/
HDMI3, you may not be able to change the Aspect depending on the input signal.
By normally selecting Auto, the optimum aspect is used to display the input signal. Change the setting if you
want to use a different aspect.
Aspect Mode Aspect Ratio for Input Signal
16:10 16:9 4:3
Normal
Full
Zoom
c
When a 4K image signal is being input, you can only select Normal.
Adjusting the Image
35
Adjusting the Sharpness
You can make the image clearer.
The following shows the setting items and procedures.
Standard
Enhances the outlines for the projected image overall. When you adjust Stand-
ard, the adjustment values for Thin Line Enhancement and Thick Line En-
hancement are also adjusted.
Thin Line Enhancement
Details such as hair and patterns on clothing are enhanced.
Thick Line Enhancement
Rough parts such as outlines for entire subjects or the background are enhanced,
making the overall image clearer.
a
Press the [Menu] button to display
menus in the order Image -
Sharpness.
Remote control Control panel
The Sharpness adjustment screen is
displayed.
b
Use the up and down buttons to select
the item, and then use the left and
right buttons to make the
adjustments.
The image is enhanced when moved to the
right (positive) and softer when moved to
the left (negative).
c
Press the [Menu] button to exit the
menu.
Adjusting the Image
36
Adjusting Image Resolution (Image Enhancement)
You can adjust the resolution of the image using the Image Enhancement function.
The following content can be adjusted.
4K Enhancement*3
4K Enhancement is a function that projects an image at a doubled res-
olution by diagonally shifting 1 pixel in increments of 0.5 pixels.
A high-resolution image signal is projected in fine detail.
Image Preset Mode
Select the settings prepared in advance as the settings for Noise Re-
duction, MPEG Noise Reduction, Super-resolution, and Detail En-
hancement.
Frame Interpolation*1 *2 *3
Plays movies smoothly. s p.37
Deinterlacing*1 *2
Converts the signal from interlaced to progressive using a method ap-
propriate for the image signal.
Noise Reduction*1 *2 *3 *4
Smoothes out rough images.
MPEG Noise Reduction*1 *2 *3
*4
You can reduce dot and block noise that occurs in outlines when pro-
jecting MPEG movies.
Super-resolution*2
Fine Line Adjust: Enhances the contrast and the outlines of complicated
images.
Soft Focus Detail: Enhances the contrast and the outlines for smooth
backgrounds.
Detail Enhancement*2
Enhances the contrast in an image to create a more emphatic texture
and material feel.
Strength: The larger the value, the stronger the contrast.
Range: The larger the value, the wider the range of detail enhancement
becomes.
*1 This can only be set when Signal - Advanced- Image Processing is set to Fine.
*2 This can be set at any time except when Image Preset Mode is set to Off.
*3 This cannot be set when 4K signals are being input.
*4 This cannot be set when 21:9 signals are being input.
a
Press the [Menu] button to display
menus in the order Image - Image
Enhancement.
Remote control Control panel
b
Use the up and down buttons to select
the item you want to adjust, and then
press the [Enter] button to confirm the
selection.
Adjusting the Image
37
c
Use the left and right buttons to make
adjustments.
Press the [Esc] button to adjust another
item.
d
Press the [Menu] button to exit the
menu.
Adjusting the Luminance for Images
When Dynamic Contrast is set to On, the luminance of the projected image is adjusted automatically.
Automatically adjusting the luminance improves the contrast according to the brightness of the image.
a
Press the [Menu] button to display
menus in the order Image - Dynamic
Contrast.
Remote control Control panel
b
Use the up and down buttons to select
the item, and then press the [Enter]
button to confirm the selection.
Setting Frame Interpolation
You can play fast moving images smoothly by automatically producing intermediate frames between the
original frames.
Frame Interpolation is available under the following conditions.
•When Image Processing is set to Fine. s Signal - Advanced - Image Processing p.62
•When the source is HDMI1/HDMI2/HDMI3.
•When inputting 2D signals* or 3D signals (1080p 24 Hz). s p.96
* This is unavailable when a 4K signal is being input. This is enabled only when 4K Enhancement is set to On and
1080p 24 Hz signals are being input. s Image - Image Enhancement - 4K Enhancement p.60
a
Press the [Menu] button to display
menus in the order Image - Image
Enhancement - Frame
Interpolation.
Remote control Control panel
b
Use the up and down buttons to select
the item, and then press the [Enter]
button to confirm the selection.
Adjusting the Image
38
Setting the Image Processing Speed
Improves the response speed for images projected at high-speed, such as games.
This is only available when receiving a progressive signal input from the HDMI1/HDMI2/HDMI3 ports.
a
Press the [Menu] button to display
menus in the order Signal -
Advanced - Image Processing.
Remote control Control panel
b
Use the up/down buttons to switch
between Fine and Fast.
c
•This does not support 3D images.
•When Image Processing is set to Fast, Noise Reduction, Frame Interpolation, Deinterlacing, and
MPEG Noise Reduction are fixed at Off.
Adjusting the Image
39
Adjusting the Color
Adjusting the Color Temp.
Adjusts the tint for the images. Make adjustments if the image is a little too blue or too red and so on.
a
Press the [Menu] button to display
menus in the order Image - White
Balance - Color Temp.
Remote control Control panel
b
Use the left and right buttons to make
adjustments.
Blue tints grow stronger as the value is
increased, and red tints grow stronger as
the value is reduced.
Adjusting the RGB (Offset and Gain)
You can adjust the brightness of dark areas (Offset) and bright areas (Gain) for R (red), G (green), and B (blue).
a
Press the [Menu] button to display
menus in the order Image - White
Balance - Custom.
Remote control Control panel
b
Use the up and down buttons to select
the item, and then use the left and
right buttons to make the
adjustments.
The image becomes brighter when moved
to the right (positive) and darker when
moved to the left (negative).
Offset
When the image is made brighter, shading for the darker sections is more vividly expressed.
When the image is made darker, the image appears more full-bodied but shading for the
darker sections is harder to distinguish.
Gain
When the image is made brighter, the bright sections become whiter and shading is lost.
When the image is made darker, shading for the bright sections is more vividly expressed.
Adjusting the Image
40
Adjusting Hue, Saturation, and Brightness
You can adjust the hue, saturation, and brightness for each of the R (red), G (green), B (blue), C (cyan), M
(magenta), and Y (yellow) colors.
Hue
Adjusts the overall color of the image to be blue, green, or red.
Saturation
Adjusts the overall vividness of the image.
Brightness
Adjusts the overall color brightness of the image.
a
Press the [Menu] button to display
menus in the order Image -
Advanced - RGBCMY.
Remote control Control panel
b
Use the up and down buttons to select
the color you want to adjust, and then
press the [Enter] button to confirm the
selection.
c
Use the up and down buttons to select
Hue, Saturation, or Brightness.
d
Use the left and right buttons to make
adjustments.
Press the [Esc] button to adjust another
color.
e
Press the [Menu] button to exit the
menu.
Adjusting the Image
41
Adjusting the Gamma
You can adjust slight coloration differences that may occur due to the device being used when the image is
displayed.
You can set it by using one of the following methods.
•Select and adjust the correction value
•Adjust using the gamma adjustment graph
Select and adjust the correction value
a
Press the [Menu] button to display
menus in the order Image -
Advanced - Gamma.
Remote control Control panel
b
Use the up and down buttons to select
the correction value, and then press
the [Enter] button to confirm the
selection.
The larger the value, the lighter the dark
portions of the image become, but bright
areas may appear discolored. The upper
part of the gamma adjustment graph
becomes rounded.
The smaller the value, the darker the bright
portions of the image become. The lower
part of the gamma adjustment graph
becomes rounded.
c
•The horizontal axis of the gamma adjustment graph shows the input signal level, and the vertical axis
shows the output signal level.
•Select Reset to return the adjustments to their default values.
Adjusting the Image
42
Adjust using the gamma adjustment graph
Select a tone point on the graph and make adjustments.
a
Press the [Menu] button to display
menus in the order Image -
Advanced - Gamma - Custom.
Remote control Control panel
b
Use the left and right buttons to select
the tone you want to adjust from the
graph.
c
Use the up and down buttons to
adjust the brightness, and then press
the [Enter] button to confirm the
selection.
Adjusting the Image
43
Viewing the Image at the Saved Image Quality
(Memory Function)
Saving a Memory
By using the memory function, you can register settings for Image from the Configuration menu, and then
load them when necessary.
a
Make the settings or adjustments you
want to register.
b
Press the [Menu] button to display
menus in the order Settings -
Memory.
Remote control Control panel
c
Use the up and down buttons to select
Save Memory, and then press the
[Enter] button to confirm the
selection.
d
Use the up and down buttons to select
the memory name you want to save,
and then press the [Enter] button to
confirm the selection.
The current projector settings are saved to
the memory.
If the mark on the left of the memory name
is turned aqua, it means the memory has
already been registered. When you select a
registered memory, a message is displayed
asking you to confirm that you want to
overwrite the memory. If you select Yes, the
previous content is erased and the current
settings are saved.
Adjusting the Image
44
Loading, Deleting, and Renaming a Memory
You can load, delete, and rename registered memories.
a
Press the [Menu] button to display
menus in the order Settings -
Memory.
Remote control Control panel
b
Select the target function on the
screen displayed.
Function Explanation
Load Memory
Loads the saved memory. When you select a memory and press the
[Enter] button, the settings applied to the current image are replaced with
the settings from the memory.
Erase Memory
Erases a saved memory. When you select a memory name and press the
[Enter] button, a message is displayed. Select Yes, and then press the
[Enter] button to erase the selected memory.
Rename Memory
Changes the memory name. Select the memory name you want to
change, and then press the [Enter] button. Enter the memory name using
the soft keyboard. s p.69
When you have finished, move the cursor over Finish, and then press the
[Enter] button.
Useful Functions
45
Enjoying 3D Images
Preparing to View 3D Images
To view 3D images, be sure to prepare a pair of commercially available 3D Glasses with an active shutter
system that supports radio waves (RF/Bluetooth) communication system in advance.
Check the following before viewing 3D images.
•The source is HDMI1/HDMI2/HDMI3
•3D Display is set to Auto or 3D
s Signal - 3D Setup - 3D Display p.62
•Pair 3D Glasses.
This projector supports the following 3D formats.
•Frame Packing
•Side by Side
•Top and Bottom
If the 3D image cannot be viewed
The projector automatically projects a 3D image when detecting a 3D format.
Some 3D TV broadcasts may not contain 3D format signals. If this happens, follow the steps below to set the
3D format.
a
Press the [Menu] button to display
menus in the order Signal - 3D Setup.
Remote control Control panel
b
Set 3D Display to 3D.
c
Press the [Esc] button to return to the
previous screen.
d
Select 3D Format, and then select the
3D format on the AV device.
Useful Functions
46
c
•If you are using a device or cable that does not support 3D images, 3D projection cannot be performed.
•For details on 3D format settings on the AV device, see the documentation supplied with the AV device.
•When the 3D format has not been correctly set up, an image will not be correctly projected as shown
below.
•If a 3D image is not projected correctly even when a 3D format is set, the synchronization timing for
the 3D Glasses may be inversed. Inverse the synchronization timing using Inverse 3D Glasses.
s Signal - 3D Setup - Inverse 3D Glasses p.62
•How a 3D image is perceived varies depending on the individual.
•When you start projecting a 3D image, a warning about viewing 3D images is displayed. You can turn
off this warning by setting 3D Viewing Notice to Off. s Signal - 3D Setup - 3D Viewing Notice p.62
•During 3D projection, the following Configuration menu functions cannot be changed.
4K Enhancement, Frame Interpolation, Aspect, Overscan (set to Off), Super-resolution, Image
Processing, Advanced - Dynamic Range
•The appearance of the 3D image may change depending on the temperature of the surroundings.
Refrain from using the projector if the image is not projected normally.
Using 3D Glasses
You can view 3D images by using a pair of commercially available 3D Glasses (with an active shutter system
that supports radio waves (RF/Bluetooth) communication system).
To view 3D images, you first need to pair the 3D Glasses with the projector. See the User's Guide supplied
with your 3D Glasses for more information.
Warnings Regarding Viewing 3D Images
Note the following important points when viewing 3D images.
Caution
Viewing Time
•When viewing 3D images, always take periodic breaks during extended viewing.
Long periods of viewing 3D images may cause eye fatigue.
The amount of time and frequency of such breaks varies from person to person. If your eyes still feel tired or
uncomfortable even after taking a break from viewing, stop viewing immediately.
Useful Functions
47
Caution
Watching 3D Images
•If your eyes feel fatigued or uncomfortable when viewing 3D images, stop viewing immediately.
Continuing to view the 3D images could cause you to feel unwell.
•When viewing 3D images be sure to always wear 3D Glasses. Do not attempt to view 3D images without 3D
Glasses.
Doing so could cause you to feel unwell.
•Do not place any breakable or fragile objects around you when using 3D Glasses.
3D images may cause you to move your body involuntarily, resulting in damage to nearby items or personal
injury.
•Only wear 3D Glasses when viewing 3D images. Do not move around while wearing 3D Glasses.
Your vision may appear darker than normal, causing you to fall or injure yourself.
•Try to stay as level with the viewing screen as possible when viewing 3D images.
Viewing 3D images at an angle reduces the 3D effect and may cause you to feel unwell due to unintended
color changes.
•When viewing 3D images in a room with fluorescent or LED lighting, you may see flashing or flickering
throughout the room. If this should occur, reduce the lighting until the flickering goes away or turn off the
lights completely when viewing 3D images. In some very rare cases, this flickering could trigger seizures or
fainting for some individuals. If you begin to feel uncomfortable or unwell at any time when viewing 3D
images, stop immediately.
•Stay at least three times the height of the screen away from the screen when viewing 3D images.
The recommended viewing distance for an 80-inch screen is at least 3 meters, and at least 3.6 meters for a
100-inch screen.
Sitting or standing any closer than the recommended viewing distance may result in eye fatigue.
Caution
Health Risks
•You should not use 3D Glasses if you are sensitive to light, have a heart condition, or are unwell.
Doing so could aggravate your pre-existing conditions.
Caution
Recommended Age of Use
•The minimum recommended age to view 3D images is six years old.
•Children under the age of six are still developing and viewing 3D images may cause complications. Consult
your doctor if you have any concerns.
•Children viewing 3D images through 3D Glasses should always be accompanied by an adult. It is often difficult
to tell when a child is feeling tired or uncomfortable, which could result in them feeling suddenly unwell.
Always check with your child to ensure that they are not experiencing any eye fatigue during viewing.
Useful Functions
48
Using the HDMI Link Function
HDMI Link Function
When an AV device that meets the HDMI CEC standards is connected to the projector's HDMI port, you can
perform linked operations such as linked power on and volume adjustment for the AV system from one
remote control.
c
•As long as the AV device meets the HDMI CEC standards, you can use the HDMI link function even if
the AV system in-between does not meet the HDMI CEC standards.
•Up to 3 multi-media players that meet the HDMI CEC standards can be connected at the same time.
Connection Example
Projector Amplifier Multi-media players and so on
HDMI Link Settings
When HDMI Link is set to On, you can perform the following
operations. s Settings - HDMI Link - HDMI Link p.63
•
Input Change Link
Changes the input source of the projector to HDMI when
content is played back on the connected device.
•
Connected Devices Operations
Using the projector's remote control, you can perform op-
erations such as Play, Fast Forward, Rewind, Pause, Volume
Adjustment, and Audio Mute.
You can also select the following functions from the HDMI
Link screen.
Function Explanation
Audio Out Device Selects which device outputs audio.
Projector: Select this to output audio from the projector’s built-in speakers or from an
external speaker connected to the Audio Out port.
AV System: Select this to output audio from an AV amplifier that supports the HDMI
CEC standards.
Power On Link When Power On Link is set, operations are linked as shown below.
•
When the projector is turned on, the connected devices are also turned on.
•
Also, when the connected devices are turned on and content is played back, the projector
turns on.
Useful Functions
49
Function Explanation
Power Off Link When Power Off Link is set to On, when the projector is turned off, the connected
devices are also turned off.
•
This only works when the connected device's CEC power link function is enabled.
•
Note that depending on the status of the connected device (for example, if it is record-
ing), the device may not power off.
Link Buffer If HDMI Link is not working correctly, you may be able to improve it by changing the
settings.
c
To use the HDMI Link function, you must configure the connected device. See the documentation
supplied with the connected device for more information.
Connecting
You can check the connected devices that are available for HDMI Link, and select on the device you want to
project the image from. Devices that can be controlled by HDMI Link automatically become the selected
device.
Before displaying the list of connected devices, check that HDMI Link is set to On.
s
Settings - HDMI
Link - HDMI Link p.63
a
Press the [Menu] button to display
menus in the order HDMI Link -
Device Connections.
Remote control Control panel
The Device Connections list is displayed.
Devices that have an aqua icon to their left
are linked by HDMI Link.
If the device name cannot be determined
this field is left blank.
b
Select the device you want to operate
using the HDMI Link function.
c
•If the cable does not meet the HDMI standards, operations are not possible.
•Some connected devices or functions of those devices may not operate properly even if they meet the
HDMI CEC standards. See the documentation and so on supplied with the connected device for more
information.
Using the Projector on a Network
50
Projecting Using Wired LAN
You can send images to your projector through a wired network.
To do this, connect the projector to your network, and then set up your projector and computer for network
projection.
When you have finished making projector connection and network settings, install Epson iProjection
(Windows/Mac) from the following Web site.
You can use Epson iProjection to project computer images over a network. You can also hold dynamic
meetings by projecting images from multiple computers connected to the network at the same time. See
the Epson iProjection Operation Guide (Windows/Mac) for more information.
https://www.epson.com
Selecting Wired Network Settings
Before you can project images over a network, you need to connect the Wireless LAN unit (ELPAP10) and
configure network settings on the projector.
c
Before making settings, connect a LAN cable to the LAN port, and connect the projector to the wired
LAN.
a
Press the [Menu] button to display menus in the order Network - Network Configuration.
Remote control Control panel
b
Select Basic, and then set the following as necessary.
•Projector Name: Enter a name up to 16 alphanumeric characters long to identify the projector over the
network.
•PJLink Password: Set a password to use when you control the projector using compatible PJLink software.
You can enter up to 32 single-byte alphanumeric characters.
•Remote Password: Set a password to use when you operate the projector from a smartphone or a tablet. You
can enter up to single-byte 8 alphanumeric characters.
•Display LAN Info.: Set the display format for the projector's network information.
c
Use the displayed keyboard to enter the name, passwords and keyword. Use the up/down/
left/right buttons on the remote control to select characters, and then press the [Enter] button
to confirm the selection.
c
Select Wired LAN, and then press the [Enter] button.
Using the Projector on a Network
51
d
Select the basic options as necessary.
•If your network uses DHCP, set DHCP to On.
•If you are not using DHCP, set DHCP to Off, and then enter the projector's IP Address, Subnet Mask, and
Gateway Address.
e
When you have finished making settings, select Complete and follow the on-screen
instructions to save your settings and exit the menus.
f
Press the source button on the remote control or the [Source] button on the control panel,
and then select LAN.
The settings are complete when you see the correct IP address on the LAN standby screen.
c
To prevent the IP address from being displayed on the LAN standby screen or the Home screen,
set IP Address Display to Off.
s
Network - Network Configuration - Wired LAN p.71
Using the Projector on a Network
52
Projecting Using Wireless LAN
You can project images from smartphones, tablets, and computers over wireless LAN.
To project over wireless LAN, you need to make wireless network settings for the projector and the connected
device in advance.
Use Epson iProjection to project images over wireless LAN. You can download Epson iProjection using any
of the following methods; however, the customer is liable for any costs involved.
•You can download Epson iProjection (Windows/Mac) from the following Web site.
http://www.epson.com
•You can download Epson iProjection (iOS/Android) from the App Store or Google Play.
Selecting Wireless Network Settings Manually
Before you can project from your wireless network, you need to select network settings for the projector.
a
Press the [Menu] button to display menus in the order Network - Wireless LAN Power.
Remote control Control panel
b
Use the up and down buttons to select On, and then press the [Enter].
c
Select Network Configuration, and then press the [Enter] button.
Using the Projector on a Network
53
d
Select Basic, and then set the following as necessary.
•Projector Name: Enter a name up to 16 alphanumeric characters long to identify the projector over the
network.
•PJLink Password: Set a password to use when you control the projector using compatible PJLink software.
You can enter up to 32 single-byte alphanumeric characters.
•Remote Password: Set a password to use when you operate the projector from a smartphone or a tablet. You
can enter up to single-byte 8 alphanumeric characters.
•Display LAN Info.: Set the display format for the projector's network information.
c
Use the displayed keyboard to enter the name, passwords and keyword. Use the up/down/
left/right buttons to select characters, and then press the [Enter] button to confirm the
selection.
e
Select Wireless LAN, and then press the [Enter] button.
f
Select the Connection Mode setting.
•Quick: Lets you connect the projector to your smartphones, tablets, or computers directly using wireless
communication. When you select Quick, go to step 10.
•Advanced: Lets you connect to multiple smartphones, tablets, or computers over a wireless network access
point. When you select Advanced, go to step 7.
g
Select Network Configuration - Wireless LAN - Search Access Point, to select the access
point you want to connect to.
c
If you need to assign the SSID manually, select SSID to enter the SSID. In addition, configure
the security settings in the Security menu.
s
p.55
Using the Projector on a Network
54
h
Assign an IP address to the projector as necessary.
•If your network uses DHCP, select IP Settings to set the DHCP setting to On.
•If you are not using DHCP, select IP Settings to set the DHCP setting to Off, and then enter the projector's IP
Address, Subnet Mask, and Gateway Address.
i
When you have finished making settings, select Complete and follow the on-screen
instructions to save your settings and exit the menus.
j
Press the source button on the remote control or the [Source] button on the control panel,
and then select LAN.
The settings are complete when you see the correct IP address on the LAN standby screen.
When you have finished making wireless settings for your projector, you need to make wireless settings on
the connected device. Then start the network software to send images to your projector through a wireless
network.
c
To prevent the SSID and IP address from being displayed on the LAN standby screen or the Home
screen, set SSID Display and IP Address Display to Off.
s
Network - Network Configuration -
Wireless LAN p.70
Using the Projector on a Network
55
Selecting the Computer's Wireless LAN Settings
To connect the computer and the projector using Advanced mode, select the correct wireless network
settings on your computer.
Selecting wireless network settings in Windows
a
To access your wireless utility software, double-click the network icon on the Windows
taskbar.
b
Select the network name (SSID) of the network the projector is connected to.
c
Click Connect.
Selecting wireless network settings in OS X
a
Click the AirMac icon on the menu bar at the top of the screen.
b
Make sure AirMac is turned on and select the network name (SSID) of the network the
projector is connected to.
Setting Up Wireless Network Security
You can set up security for your projector to use on a wireless network. Set up one of the following Connection
Mode to match the settings used on your network:
•WPA2 security
•WPA/WPA2 security
a
Press the [Menu] button to display menus in the order Network - Network
Configuration - Security.
Remote control Control panel
b
Select the security settings to match your network settings.
Using the Projector on a Network
56
c
When you have finished making settings, select Complete and follow the on-screen
instructions to save your settings and exit the menus.
Projecting in Epson iProjection (iOS/Android)
You can display a QR code on the screen and project data easily from a smartphone or tablet using the Epson
iProjection app (V3.2.0 or later).
c
•You can download Epson iProjection for free from the App Store or from Google Play. Any fees incurred
when communicating with the App Store or Google Play are the responsibility of the customer.
•When using Epson iProjection in Quick connection mode, we recommend making security settings.
s p.55
a
To display the QR code, press the [Menu] button, and then select Network - Display the
QR Code.
Remote control Control panel
c
•If you press the [Home] button on the control panel, you can also display the QR code from the
Connection Guideon the Home screen. s p.26
•To hide the QR code, press the [Esc] button.
b
Start Epson iProjection on your smartphone or tablet.
c
Read the projected QR code on your smartphone or tablet.
Read the code from in front of the screen so that the QR code fits into the guide. If you are too far from
the screen, the code may not be read.
Once connected, go to and select the Contents menu, and then select a file you want to project.
Using the Projector on a Network
57
Operating using a smartphone (remote control function)
By using Epson iProjection, you can operate the projector from a smartphone or tablet.
Tap in Epson iProjection to display the menu.
Tap Remote Control on the menu to display the following screen.
c
When Remote Password is set, you need to enter the password. Once the password has been
recognized, you do not need to enter it from the second time.
Button Function
a
Displays the menu.
b
Turns the projector on or off.
c
Changes to the image from each input port. s p.25
d
Sets the image quality using the on-screen instructions.
e
Saves, loads, erases, or rename a memory. s p.43
f
Turns HDMI Link on or off. s p.48
g
When HDMI Link is On, you can perform operations such as Play,
Stop, Fast Forward, Rewind, Next Chapter, Previous Chapter, and
Pause.
h
Allows you to specify Color Mode, Frame Interpolation, Image
Enhancement, Image Processing, Dynamic Contrast, Light Out-
put, White Balance, Gamma, and RGBCMY.
i
Allows you to specify 3D Display, 3D Format, 3D Depth, Diagonal
Screen Size, and 3D Brightness.
j
Allows you to specify Aspect, Keystone, Reset All, Reset Memo-
ry, Test Pattern, Zoom, Image Shift.
k
When HDMI Link is set to On, you can adjust the volume.
Configuration Menu
59
Configuration Menu Functions
Configuration Menu Operations
On the Configuration menu, you can make adjustments and settings for Signal, Image, Input Signal, and so on.
a
Press the [Menu] button.
Remote control Control panel
The Configuration menu is displayed.
b
Use the up and down buttons to select
the top menu on the left, and then
press the [Enter] button to confirm the
selection.
When you select the top menu on the left,
the sub menu on the right changes.
The line at the bottom is a guide for
operations.
c
Use the up and down buttons to select
the sub menu on the right, and then
press the [Enter] button to confirm the
selection.
The adjustment screen for the selected
function is displayed.
d
Use the up/down/left/right buttons to
adjust the settings.
Ex.) Adjustment bar
Ex.) Choices
Press the [Enter] button on an item
displaying this icon to change to the
selection screen for that item.
Press the [Esc] button to return to the
previous level.
e
Press the [Menu] button to exit the
menu.
Configuration Menu
60
Configuration Menu Table
If there is no image signal being input, you cannot adjust items related to the Image or Signal in the
Configuration menu. Note that the items displayed for the Image, Signal, and Info vary depending on the
image signal being projected.
Image menu
Function Menu/Settings Explanation
Color Mode
Dynamic, Bright Cinema, Cinema, Game Select a color mode based on your sur-
roundings and the image you are projec-
ting. s p.33
Brightness
Adjusts the brightness when the image
appears too dark.
Contrast
Adjusts the contrast between light and
shade in the images. By increasing the
contrast, the images become vivid.
Color Satura-
tion
Adjusts the color saturation for the im-
ages.
Tint
Adjusts the tint for the images.
Sharpness
Adjusts the image sharpness.
White Balance
Color Temp. Adjusts the tint for the images. The image
is tinted blue for high values, and tinted
red for low values.
G-M Correction The image becomes greener when set to
a positive value and redder when set to a
negative value.
Custom Adjusts the offset and gain for each R, G,
and B color.
Grayscale Adjustment Level, Red,
Green, Blue, Brightness
Adjusts red, green, blue, and brightness
for the selected adjustment level.
Configuration Menu
61
Function Menu/Settings Explanation
Image En-
hancement*1
4K Enhancement On, Off You can project at a doubled resolution.
Image Preset Mode Off, Preset 1 to Preset 5 Select the settings prepared in advance as
the settings for Frame Interpolation, De-
interlacing, Noise Reduction, MPEG
Noise Reduction, Super-resolution, and
Detail Enhancement.
Frame Interpolation Off, Low, Normal, High Adjusts the smoothness of movement of
the image.
Deinterlacing Off, Video, Film/Auto (This can only be set when Image Pro-
cessing is set to Fine or when receiving a
480i, 576i, or 1080i signal input from the
HDMI1/HDMI2/HDMI3 ports.)
Converts the signal from interlaced (i) to
progressive (p) using a method appropri-
ate for the image signal.
•
Off: This is ideal for dynamic motion im-
ages.
•
Video: This is ideal for viewing general
video images.
•
Film/Auto: Performs the optimal conver-
sion for film, CG, or animation input sig-
nals.
Noise Reduction Adjusts the roughness of the image.
MPEG Noise Reduction Smoothes out rough images in MPEG for-
mat.
Super-resolution Fine Line Adjust, Soft
Focus Detail
Adjusts the amount of enhancement for
complicated images and backgrounds.
Detail Enhancement Strength, Range Creates a more emphatic texture and ma-
terial feel of the image.
Advanced
Gamma 2, 1, 0, -1, -2, Custom
*2
,
Reset
Performs gamma adjustments. You can
select a raw value or adjust using a custom
value. s p.41
RGBCMY R/G/B/C/M/Y Hue, Satura-
tion, Bright-
ness
Adjusts the Hue, Saturation, and Bright-
ness for each R, G, B, C, M, and Y col-
or. s p.40
Light Output
Sets the brightness for the light source.
Dynamic Con-
trast
Off, Normal, High Speed Adjusts the projection luminance accord-
ing to the brightness of the image. s p.37
Reset
Yes, No Resets the adjustment values of Image set
in the current Color Mode to the default
settings.
*1 Only when an HDMI1, HDMI2, or HDMI3 image signal is being input.
*2 Settings are saved for each type of input source or Color Mode.
Configuration Menu
62
Signal menu
The Signal menu cannot be set when a LAN image signal is being input.
Function Menu/Settings Explanation
3D Setup
3D Display Auto, 3D, 2D To view 3D images, set this to Auto or
3D. s p.45
3D Format Side by Side, Top
and Bottom
Sets the 3D format for the input signal.
3D Depth -10 to 10 Sets the depth for the 3D image.
Diagonal Screen
Size
60 to 300 Sets the projection size for the 3D image. By
matching this to the actual size, you can achieve
the optimum 3D effect.
3D Brightness Low, Medium, High Sets the brightness for the 3D image.
Inverse 3D Glasses Reverses the synchronization timing for the left/
right shutters on the 3D Glasses and the left/right
images. Enable this function if the 3D effect is not
displayed correctly.
3D Viewing Notice On, Off Turns the notice that appears when viewing 3D
content on or off.
Aspect*1
Auto
*2
, Normal, Full, Zoom Selects the aspect mode. s p.33
Overscan*1
Auto, Off, 4%, and 8% Changes the output image ratio (the range of the
projected image).
•
Off, 4%, 8%: Sets the range of the image. When
set to Off, the entire range of the image is pro-
jected. Depending on the image signal, you may
notice noise at the top and bottom of the image.
•
Auto: Automatically sets to Off or 8% depend-
ing on the input signal.
Color Space
Auto, BT.709, BT.2020 Sets the conversion system for the color space.
Dynamic
Range
Dynamic Range Auto, SDR, HDR10,
HLG
Lets you change the range of dark and bright
areas in images.
Signal Status - Displays the image signal.
HDR10 Setting 1 to 16 Lets you change the PQ curve of the dynamic
range in the HDR PQ method.
HLG Setting 1 to 16 Lets you change the HLG curve of the dynamic
range in the HDR HLG method.
Configuration Menu
63
Function Menu/Settings Explanation
Advanced
Video Range
*1
Auto, Limited
(16-235), Full
(0-255)
When set to Auto, the video level for the DVD
signal being input to the HDMI1/HDMI2/HDMI3
ports is automatically detected and set.
If you experience under or overexposure when
set to Auto, set the video level of the projector
to match that of the DVD/Blu-ray disc player's
video level. Your player may be set to Normal
(Limited) or Expand (Full).
EDID Expanded, Normal,
21:9
Lets you change the EDID settings.
Expanded supports 3840 x 2160 60 Hz signals,
Normal supports 3840 x 2160 30 Hz signals, and
21:9 supports 2560 x 1080 60 Hz signals.
Image Processing Fine, Fast Improves the response speed for images projec-
ted at high-speed, such as games.
Reset
Yes, No Resets all Signal settings except for Diagonal
Screen Size, 3D Viewing Notice, and Aspect.
*1 Settings are saved for each type of input source or signal.
*2 You may not be able to make selections depending on the source or type of signal.
Settings menu
Function Menu/Settings Explanation
Installation
Guide
- Displays a guide so that you can adjust the posi-
tion during installation.
Keystone
H/V-Keystone
V-Keystone -12 to 12
Corrects keystone distortion. s p.30
•
H/V-Keystone: Manually corrects horizontal and
vertical distortions. s p.30
•
Quick Corner: Corrects the corners of the pro-
jected image individually. s p.31
H-Keystone -12 to 12
Quick Corner -
Blanking
Covers part of the image with a blank (black
screen). You can set the top, bottom, left, or right
of the image.
Zoom
Adjusts the size of the image. s p.28
Image Shift
- Adjusts the position of the projected image with-
out having to move the projector. s p.29
Volume
Adjusts the volume.
Configuration Menu
64
Function Menu/Settings Explanation
HDMI Link
Device Connections - Displays a list of devices connected to the
HDMI1/HDMI2/HDMI3 ports.
HDMI Link On, Off Enables or disables the HDMI Link function.
Audio Out Device Projector, AV Sys-
tem
Selects which device outputs audio. s p.48
Power On Link Off, Bidirectional,
Device -> PJ, PJ ->
Device
Sets the link function when the power is turned
on.
•
When linking operations to the connected de-
vice and turning on the projector, select Bidir-
ectional or Device -> PJ.
•
When linking power on for the projector to the
connected device, select Bidirectional or PJ ->
Device.
Power Off Link On, Off Sets whether or not to power off connected de-
vices when the projector is turned off.
Link Buffer On, Off If HDMI Link is not working correctly, you may be
able to improve it by changing the settings.
Lock Setting
Child Lock On, Off This locks the standby button on the projector's
control panel to prevent children from turning
on the projector by accident. You can turn on the
power when locked by holding down the stand-
by button for approximately three seconds. You
can still turn off the device using the standby
button or perform operations with the remote
control as usual.
If changed, this setting is enabled after you pow-
er off the projector and the cool-down process is
complete.
Note that even if Child Lock is set to On, the pro-
jector still turns on when the power cord is con-
nected if Direct Power On is set to On.
Control Panel Lock Full Lock, Partial
Lock, Off
Full Lock: Disables all of the projector's buttons.
Partial Lock: Disables all of the projector's but-
tons except for the standby button.
is displayed on the screen if buttons are
pressed while the projector is locked. To unlock,
press and hold the standby button on the control
panel for at least 7 seconds.
If changed, this setting is enabled once you close
the Configuration menu.
Configuration Menu
65
Function Menu/Settings Explanation
Memory
Load Memory Memory1 to Memo-
ry10
Loads the settings saved in Save Memory to ad-
just the image.
Save Memory Memory1 to Memo-
ry10
Saves the settings made in Image to a memory.
Erase Memory Memory1 to Memo-
ry10
Erases a saved memory.
Rename Memory Memory1 to Memo-
ry10, Default, DVD,
VCR, SDTV, HDTV,
Cinema, Sports, Mu-
sic, Anime, Game,
Custom
Changes the saved memory name.
Reset
Yes, No Resets the adjustment values for Keystone,
Blanking, Volume, HDMI Link, and Lock Set-
ting.
Extended menu
Function Menu/Settings Explanation
Home Screen
Home Screen
Auto Disp.
On, Off Selects whether or not to display the Home
screen automatically when the projector turns
On. The Home screen is not displayed when the
selected source has an image signal when the
projector turns on.
Custom
Function 1
Dynamic Contrast, Key-
stone, Info, Installation
Guide
Select the function assigned to the Home screen.
Custom
Function 2
Configuration Menu
66
Function Menu/Settings Explanation
Display
Messages On, Off Sets whether or not to display the following mes-
sages (On or Off).
•
Item names for image signals, color modes, and
aspect ratios.
•
If the internal temperature is rising when no im-
age signal is being input or an unsupported sig-
nal is detected.
Display Back-
ground
Black, Blue, Logo Selects the screen status when no image signal
is being input.
Startup
Screen
On, Off Sets whether or not to show a startup screen
when projection begins (On or Off). If changed,
this setting is enabled after you power off the
projector and the cool-down process is com-
plete.
Standby Con-
firmation
On, Off Sets whether or not to display a standby confir-
mation message (On or Off). s p.27
Panel Align-
ment
-s p.68
Color Uni-
formity
Color Uni-
formity
On, Off
Enables or disables Color Uniformity.
Adjustment
Level
There are eight levels from white, through gray,
and up to black. You can adjust each level indi-
vidually.
Start Adjust-
ments
Red, Green,
Blue
Starts making Color Uniformity adjustments.
Reset
Yes, No
Resets all adjustments and settings for Color Uni-
formity to their default values.
Projection
Front, Front/Upside Down Change this setting depending on how the pro-
jector is installed.
Configuration Menu
67
Function Menu/Settings Explanation
Operation
Direct Power
On
On, Off You can set up the projector so that projection
starts as soon as the power cord is plugged in
without any button operations.
Note that when this is set to On, projection starts
if power is restored after a blackout or other
power outage and the power cord is still plugged
into the projector.
Sleep Mode On, Off If the set time is exceeded and no signal is input,
the projector is automatically turned off and en-
ters standby mode. When in standby mode,
press the power button on the remote control or
the standby button on the control panel to re-
start projection.
Sleep Mode
Timer
1 to 30 mins. Sets the interval for Sleep Mode.
Illumination On, Off Set this to Off if the light from the indicators on
the control panel bother you when watching a
movie in a dark room.
High Altitude
Mode
On, Off Set this to On if you are using the projector above
an altitude of 1500 meters.
Quick Startup Off, 20min., 60min.,
90min.
Set how long you want to Quick Startup mode to
be available. Turn off the projector to enter Quick
Startup mode. In Quick Startup mode, you can
project within seconds of pressing the power
button.
In Quick Startup mode, the standby power con-
sumption increases.
USB Power in
Standby (on-
ly some coun-
tries and re-
gions)
On, Off When set to On, power is also supplied to the
streaming media player from the USB power ca-
ble when the projector is in standby mode (pow-
er off). If the internal temperature of the projector
gets too hot, power may stop automatically.
Log Save Des-
tination
Internal Memory, USB and
Internal Memory
Set where you want to save the logs.
Standby Mode
Communication Off, Communication On Communication On indicates that the projector
can be monitored over a network when the pro-
jector is in standby mode.
Language
- Selects the display language.
Reset
Yes, No Resets all Extended settings except for Memo-
ry, Projection, High Altitude Mode, Standby
Mode, USB Power in Standby and Language.
Configuration Menu
68
Panel Alignment menu
Menu/Settings Explanation
Panel Alignment Panel Alignment On, Off Enables or disables Panel Alignment.
Select Color R, B Select the color to correct.
Pattern Color R/G/B, R/G, G/B Select the pattern used for correc-
tion.
Start Adjust-
ments
-Starts Panel Alignment. s p.90
Memory Load Panel
Alignment
Memory1,
Memory2,
Memory3
Loads settings saved using the Save
Panel Alignment function.
Save Panel
Alignment
Memory1,
Memory2,
Memory3
Saves the settings made in Panel
Alignment to a memory.
Erase Panel
Alignment
Memory1,
Memory2,
Memory3
Erases memories registered using
the Panel Alignment function.
Rename Panel
Alignment
Memory1,
Memory2,
Memory3
Renames Panel Alignment memo-
ries.
Reset Yes, No Resets the correction value.
Network menu
Function Menu/Settings Explanation
Wireless LAN Power
On, Off Sets whether or not (On or Off) to use Wireless LAN
Power.
Net. Info. - Wireless LAN
- Displays the following network settings.
•
Connection Mode
•
Wireless LAN system
•
Antenna Level
•
Projector Name
•
SSID
•
DHCP
•
IP Address
•
Subnet Mask
•
Gateway Address
•
MAC Address
•
Region Code
Net. Info. - Wired LAN
- Displays the following network settings.
•
Projector Name
•
DHCP
•
IP Address
•
Subnet Mask
•
Gateway Address
•
MAC Address
Configuration Menu
69
Function Menu/Settings Explanation
Display the QR Code
- Displays network information for the projector with a
QR code.
Network Configuration
- Displays the screen to set the network. s p.69
Notes on operating the Network menu
Basic operations are made in the same way as when using the Configuration menu.
However, be sure to select the Complete menu to save your settings when done.
Yes:
Saves the settings and exits the Network menu.
No:
Exits the Network menu without saving the settings.
Cancel:
Continues displaying the Network menu.
Soft keyboard operations
In the Network menu, the soft keyboard appears when you need to enter numbers and characters. Use the
up/down/left/right buttons on the remote control or control panel to select keys, and then press the
[Enter] button to input the text. Press Finish to confirm your input, or Cancel to cancel your input.
CAPS key:
Switches between uppercase and lowercase letters.
SYM1/2 key:
Switches the symbol keys.
Basic menu
Function Menu/Settings Explanation
Projector Name
Up to 16 alphanumeric
characters
Enter a name to identify the projector over a network.
PJLink Password
Up to 32 alphanumeric
characters
Set a password to use when you control the projector using
compatible PJLink software. s p.94
Remote Password
Up to 8 alphanumeric
characters
Set a password to use when you operate the projector from
a smartphone or a tablet.
Display LAN Info.
Text & QR Code, Text Set the display format for the projector's network information.
Configuration Menu
70
Wireless LAN menu
Function Menu/Settings Explanation
Connection Mode
Quick, Advanced Determines how the wireless LAN is connected.
Quick: Using Epson iProjection allows you to connect to
smartphones, tablets, or computers directly using wireless
communication. The projector becomes a simple access
point. (Make sure the number of devices connected to the
projector is six or less. It may take longer to update the pro-
jected image if the number of connected devices exceeds this
number.)
Advanced: Lets you connect to multiple smartphones, tab-
lets, or computers over a wireless network access point.
Channel*1
1ch, 6ch, 11ch Select the frequency bandwidth used by the wireless LAN.
SSID*2
Up to 32 alphanumeric
characters
Enter an SSID. When an SSID is provided for the wireless LAN
system in which the projector participates, enter the SSID.
Search Access
Point*2
To Search View Search for available wireless network access points.
indicates currently connected access points. indicates
the access points where security is set.
If you select an access point that has security enabled, Secur-
ity menu appears. s p.70
IP Settings*2
DHCP Set whether or not (On/Off) to use DHCP. If this is set to On,
you cannot set any more addresses.
IP Address Inputs the IP address for the projector.
The following IP addresses cannot be used.
0.0.0.0, 127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a
number from 0 to 255)
Subnet Mask Enter the projector's subnet mask.
The following subnet masks cannot be used.
0.0.0.0, 255.255.255.255
Gateway Address Enter the projector's gateway IP address.
The following gateway addresses cannot be used.
0.0.0.0, 127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a
number from 0 to 255)
SSID Display
On, Off Sets whether or not to display the SSID on the LAN Standby
screen and the Home screen (On or Off).
IP Address Display
On, Off Sets whether or not to display the IP address on the LAN
Standby screen and the Home screen (On or Off).
*1 This can only be set when Connection Mode is set to Quick.
*2 This can only be set when Connection Mode is set to Advanced.
Security menu
Function Menu/Settings Explanation
Security
No, WPA2-PSK, WPA/
WPA2-PSK
Sets the security.
In Quick, WPA2-PSK is selectable. In Advanced, WPA2-
PSK/WPA/WPA2-PSK is selectable.
Passphrase
From 8 to 32 single-
byte alphanumeric
characters
Inputs the passphrase.
It is recommended to change the passphrase periodically for
the purpose of security.
Configuration Menu
71
Wired LAN menu
Function Menu/Settings Explanation
DHCP
On, Off Set whether or not (On/Off) to use DHCP. If this
is set to On, you cannot set any more addresses.
IP Address
Number from 0 to 255 Enter the IP address assigned to the projector.
You can enter a number from 0 to 255 in each
field of the address. However, the following IP
addresses cannot be used.
0.0.0.0, 127.x.x.x, 224.0.0.0 to 255.255.255.255
(where x is a number from 0 to 255)
Subnet Mask
Number from 0 to 255 Enter the projector's subnet mask.
You can enter a number from 0 to 255 in each
field of the address. However, the following sub-
net masks cannot be used.
0.0.0.0, 255.255.255.255
Gateway Address
Number from 0 to 255 Enter the projector's gateway IP address.
You can enter a number from 0 to 255 in each
field of the address. However, the following gate-
way addresses cannot be used.
0.0.0.0, 127.x.x.x, 224.0.0.0 to 255.255.255.255
(where x is a number from 0 to 255)
IP Address Display
On, Off Set to Off to prevent the IP address from being
displayed on the Net. Info. - Wired LAN screen.
Others menu
Function Menu/Settings Explanation
PJLink Notifica-
tion
On, Off To use the notification function of PJLink, select
On.
Notified IP Ad-
dress
Number from 0 to 255 Enter the IP address of a computer to be notified
of the projector’s operating status using the
PJLink notification function.
You can enter numbers from 0 to 255. The fol-
lowing IP addresses cannot be used.
127.x.x.x, 224.0.0.0 to 255.255.255.255 (x is a
number from 0 to 255)
AMX Device Dis-
covery
On, Off When you want to allow the projector to be de-
tected by AMX Device Discovery, set this to On.
Set this to Off if you are not connected to an en-
vironment controlled by a controller from AMX
or AMX Device Discovery.
Control4 SDDP
On, Off When you want to allow the projector to be de-
tected by Control4 SDDP, set this to On. Set this
to Off if you are not connected to an environ-
ment controlled by a controller from Control4 or
Control4 SDDP.
Configuration Menu
72
Reset menu
Function Explanation
Reset network settings.
You can reset all adjustment values for Network to their default settings.
Info menu
Function Menu/Settings Explanation
Projector Info
Operation Hours Displays the usage time since the projector was turned on.
Source Displays the current input source.
Input Signal
*
Displays the input signal setting of the current input source.
Resolution
*
Displays the resolution.
Scan Mode
*
Displays the scan mode.
Refresh Rate
*
Displays the refresh rate.
3D Format
*
Displays the 3D format of the signal input during 3D projec-
tion (Side by Side or Top and Bottom).
Sync Info
*
Displays the image signal information.
This information may be needed if service is required.
Color Depth
*
Displays the color depth and color difference.
Color Format
*
Displays information on the Color Space and Dynamic Range.
Status This is information about errors that have occurred on the
projector.
This information may be needed if service is required.
Serial Number Displays the projector's serial number.
Event ID The application error log appears. s p.85
Light Source Info
Light Source Hours Displays the light source usage time.
Version
Main Displays the firmware version of the projector.
Video2
*This is not displayed when a LAN image signal is being input.
Reset menu
Function Explanation
Reset Memory
Resets all items for Memory to their default settings.
Reset All Config
Resets all items in the Configuration menu to their default settings.
The following adjustment values are not reset to their defaults: Zoom, Image
Shift, Memory, Panel Alignment, Color Uniformity, Operation Hours, Lan-
guage and Network Settings.
Troubleshooting
73
Problem Solving
Handling Problems
If the projector is not operating correctly, turn off the power, reconnect the power cord, and then turn it on
again.
If this does not solve the problem, check the following points.
•Use the indicators to check the status of the projector.
•See the list of problems in this guide for information on solving problems.
If you cannot solve the problem, contact your local dealer or the contact information provided in the Epson
Projector Contact List.
Reading the Indicators
You can check the status of the projector from the flashing and lit Indicators on the control panel.
Temperature indicator
Laser indicator
Status indicator
Standby indicator
Refer to the following table to check the projector's status and how to remedy problems shown by the
indicators.
Troubleshooting
74
Indicator status during an error/warning
: Lit : Flashing : Status dependent : Off
Indicators Status Remedy
High Temp Warning
You can continue projecting. If the temperature rises too high
again, projection stops automatically.
•
Make sure that the air filter and exhaust vents are not blocked,
and that air flow is not being blocked by any objects or walls
around the projector.
•
If the air filter is clogged, clean or replace it. s p.86, p.88
•
Make sure that nothing is blocking the area around the inlet
and that the temperature around the inlet is not too high.
s p.101
Internal Error
The projector has malfunctioned.
Remove the power plug from the electrical outlet, and contact
your local dealer or the nearest Epson repair center. s Epson
Projector Contact List
Fan Error
Sensor Error
Laser Warning
A laser warning has occurred.
Remove the power plug from the electrical outlet, and contact
your local dealer or the nearest Epson repair center. s Epson
Projector Contact List
Laser Error
A laser error has occurred.
Remove the power plug from the electrical outlet, and contact
your local dealer or the nearest Epson repair center. s Epson
Projector Contact List
High Temp Error
(Overheating)
The internal temperature is too high.
•
The projector turns off automatically and you cannot project
until it has cooled down. Wait for about five minutes. When the
fan has stopped, disconnect the power cord.
•
Make sure that the air filter and exhaust vents are not blocked,
and that air flow is not being blocked by any objects or walls
around the projector.
•
If the air filter is clogged, clean or replace it. s p.86, p.88
•
Make sure that nothing is blocking the area around the inlet
and that the temperature around the inlet is not too high.
s p.101
•
If turning the power back on does not clear the problem, stop
using the projector and remove the power plug from the elec-
trical outlet. Contact your local dealer or the nearest Epson re-
pair center. s Epson Projector Contact List
•
When using at an altitude of 1500 m or more, set High Altitude
Mode to On. s Extended - Operation - High Altitude
Mode p.65
Troubleshooting
75
Indicator status during normal operation
: Lit : Flashing : Status dependent : Off
Indicators Status Remedy
Standby condition
When you press the power button on the remote control, or the
standby button on the control panel, projection starts after a
short wait.
When Standby Mode is set to Communication On, the standby
indicator remains on even when the projector is standing by.
Warm-up in progress
Warm-up time is about 30 seconds.
The power-off operation is disabled while the projector is warm-
ing-up.
Cool-down in pro-
gress
All operations are disabled while the projector is cooling-down.
Projection in pro-
gress
The projector is operating normally.
c
•Under normal operating conditions, the temperature and laser indicators are off.
•When the Illumination function is set to Off, all indicators are off under normal projection conditions.
s Extended - Operation - Illumination p.65
Troubleshooting
76
When the Indicators Provide No Help
Check the problem
Check the following table to see if your problem is mentioned, and go to the appropriate page for information
on handling the problem.
Problem Page
Problems relating to im-
ages
No images appear
Projection does not start, the projection area is completely black, or
the projection area is completely blue.
p.77
Moving images are not displayed p.77
"Not supported" is displayed p.77
"No Signal" is displayed p.78
Keystone distortion of projected image p.78
Images are fuzzy or out of focus p.78
Interference/distortion appear in images p.78
Part of the image is truncated (large) or small p.79
Image colors are not right
The whole image appears purplish or greenish, images are black &
white, or colors appear dull.
*
p.79
Images appear dark p.79
Projection stops automatically p.80
Noise problems No audio, or the audio is too low p.80
Problems when projection
starts
The projector does not turn on p.80
Problems with the remote
control
The remote control does not respond p.81
Problems with the control
panel
Cannot make settings on the control panel p.81
Problems with 3D Cannot project correctly in 3D p.82
Problems with HDMI HDMI Link does not function p.82
The device name is not displayed under Device Connections p.83
Problems with a streaming
media player
Cannot view images from a streaming media player p.83
Network problems Cannot access the network via wireless LAN p.83
The settings cannot be modified using the remote controller function
for Epson iProjection
p.84
The image contains static during network projection p.84
*Because color reproduction differs between monitors and computer LCD screens, the image projected by the
projector and the color tones displayed on the monitor may not match, however this is not a fault.
Troubleshooting
77
Problems relating to images
No images appear
Check Remedy
Is the power turned on? Press the power button on the remote control or the standby
button the control panel to turn on the projector.
Is the power cord connected? Connect the power cord.
Are the indicators switched off? Disconnect and then reconnect the projector's power cord.
Check that pressing the power button after connection supplies
the projector with power.
Is an image signal being input? Check that the connected device is turned on. When Messag-
es is set to On from the Configuration menu, image signal mes-
sages are displayed. s Extended - Display - Messages p.65
Has the power to the AV amplifier been dis-
connected?
If an AV amplifier is connected, check the AV amplifier's power
supply.
Is an image signal being sent from the device? Check that an image signal is being sent from the connected
device.
Are the Configuration menu settings correct? Reset all of the settings. s Reset - Reset All Config p.72
(Only when projecting computer image sig-
nals)
Was the connection made while the power of
the projector or the computer was already
turned on?
If the connection is made while the power is already turned on,
the Fn key (Function key) that changes the computer's image
signal to external output may not work. Turn off the power for
the computer and the projector and then turn it back on again.
Is power being supplied to the streaming me-
dia player?
When projecting from a streaming media player, make sure that
the USB power cable is connected correctly.
Are you able to connect to Wi-Fi? You need an Internet connection to view online content. Make
sure you can connect to Wi-Fi.
Is the streaming media player turned off? Use the remote control for Android TV
TM
to turn on your stream-
ing media player.
Moving images are not displayed
Check Remedy
(Only when projecting computer image sig-
nals)
Is the computer's image signal set to external
output and to output to the LCD monitor at
the same time?
Depending on the computer's specifications, moving images
may not be displayed when the computer is set to external out-
put and to the LCD monitor output at the same time.
Change it so that the image signal is set to external output only.
For the computer's specifications, see the documentation sup-
plied with the computer.
"Not supported" is displayed
Check Remedy
(Only when projecting computer image sig-
nals)
Do the image signal's frequency and resolu-
tion correspond to the mode?
Check the image signal being input in Resolution from the Con-
figuration menu, and check that it matches the projector's reso-
lution. s Info - Projector Info p.72
s "Supported Resolutions" p.96
Troubleshooting
78
"No Signal" is displayed
Check Remedy
Are the cables connected correctly?Check that all the cables required for projection are securely
connected. s p.18
Is the correct image input port selected? Switch the image with the source buttons on the remote control.
s p.25
Is the connected device turned on? Turn on the device.
(Only when projecting computer image sig-
nals)
Are the image signals being output to the
projector?
Change it so that the image signal is set to external output, and
not just the computer's LCD monitor. For some models, when
the image signals are output externally, they no longer appear
on the LCD monitor.
For the computer's specifications, see the documentation sup-
plied with the computer.
If the connection is made while the power of the projector or the
computer is already turned on, the Fn key (Function key) that
changes the computer's image signal to external output may not
work. Turn the power for the computer and the projector off and
then back on again.
Keystone distortion of projected image
Check Remedy
Is keystone distortion adjusted within the cor-
rection range?
If projecting the image from outside of the correctable range,
you may not be able to correct the keystone distortion com-
pletely. Install the projector horizontally and parallel to the front
of the screen as much as possible, and then adjust the projection
position using Image Shift. s p.15
Images are fuzzy or out of focus
Check Remedy
Has the focus been adjusted? Adjust the focus. s p.28
Is the lens cap attached? Remove the lens cap.
Is the projector at the correct distance? Check the recommended projection range. s p.17
Has condensation formed on the lens? If the projector is suddenly taken from a cold environment to a
warm environment, or if sudden ambient temperature changes
occur, condensation may form on the surface of the lens, and this
may cause the images to appear fuzzy. Set the projector up in
the room about one hour before it is used. If the projector is wet
from condensation, turn off the projector, disconnect the power
cord, and leave it for a while.
Interference or distortion appear in images
Check Remedy
Are the cables connected correctly?Check that all the cables required for projection are securely
connected. s p.18
Troubleshooting
79
Check Remedy
Is an extension cable being used? If an extension cable is used, electrical interference may affect
the signals.
(Only when projecting computer image sig-
nals)
Is the correct resolution selected?
Set the computer so that the signals being output are compatible
with the projector. s p.96
Have you connected an AV system that does
not support ARC?
If you connect an AV system that does not support ARC to the
HDMI2 (ARC) port, the image may be distorted.
Part of the image is truncated (large) or small
Check Remedy
Is the correct Aspect selected? Select the aspect mode to match the input signal in Aspect from
the Configuration menu. s Signal - Aspect p.62
(Only when projecting computer image sig-
nals)
Is the correct resolution selected?
Set the computer so that the signals being output are compatible
with the projector. s p.96
Image colors are not right
Check Remedy
Are the cables connected correctly?Check that all the cables required for projection are securely
connected. s p.18
Is the contrast adjusted correctly? Adjust the Contrast setting from the Configuration menu.
s Image - Contrast p.60
Is the color adjusted correctly? Adjust the Advanced setting from the Configuration menu.
s Image - Advanced p.60
(Only when projecting images from a video
device)
Are the color saturation and tint adjusted cor-
rectly?
Adjust the Color Saturation and Tint settings from the Config-
uration menu. s Image - Color Saturation/Tint p.60
Images appear dark
Check Remedy
Is the image brightness set correctly? Adjust the Brightness setting from the Configuration menu.
s Image - Brightness p.60
Is the contrast adjusted correctly? Adjust the Contrast setting from the Configuration menu.
s Image - Contrast p.60
Troubleshooting
80
Projection stops automatically
Check Remedy
Is Sleep Mode enabled? If the set time is exceeded and no signal is input, the laser is
automatically turned off and the projector enters standby mode.
Press the power button on the remote control or the standby
button on the control panel to turn on the projector. If you want
to disable Sleep Mode, change the setting to Off. s Exten-
ded - Operation - Sleep Mode p.65
Noise problems
No audio, or the audio is too low
Check Remedy
Is the audio cable connected correctly? Try disconnecting the cable from the Audio Out port, and then
reconnecting.
Is the volume too low? Adjust the volume so that you can hear the audio. s p.32
Is it connected with an HDMI cable? If no audio is output when connecting via an HDMI cable, set the
connected equipment to PCM output.
Are the Audio Out Device settings correct? Check that the Audio Out Device settings are correct on the
Configuration menu. s Settings - HDMI Link - Audio Out De-
vice p.63
Have you connected a streaming media play-
er or video equipment?
Make sure that the volume for the streaming media player or the
video equipment is high enough, and that the audio output set-
tings are correct.
Have you connected an ARC compatible AV
system?
Make sure that an ARC compatible AV system is connected to the
HDMI2 port.
Check that the following settings are correct on the Configura-
tion menu.
•
Set Audio Out Device to AV System. s Settings - HDMI Link
- Audio Out Device p.63
•
When the AV System is connected to the projector, set HDMI
Link to On. s Settings - HDMI Link p.63
Problems when projection starts
The projector does not turn on
Check Remedy
Is the power turned on? Press the power button on the remote control or the standby
button the control panel to turn on the projector.
Is Child Lock set to On? When Child Lock is set to On from the Configuration menu, hold
down the standby button on the control panel for approximately
three seconds, or perform operations from the remote control.
s Settings - Lock Setting - Child Lock p.63
Troubleshooting
81
Check Remedy
Do the indicators turn on and off when the
power cord is touched?
Turn off the projector, and then disconnect and reconnect the
projector's power cord. If the problem continues, stop using the
projector, remove the power plug from the electrical outlet, and
contact your local dealer or the nearest projector information
center. s Epson Projector Contact List
Problems with the remote control
The remote control does not respond
Check Remedy
Is the remote control light-emitting area
pointing towards the remote receiver on the
projector during operation?
Point the remote control towards the remote receiver. Also,
check the operating range. s p.23
Is the remote control too far from the projec-
tor?
Check the operating range. s p.23
Is direct sunlight or strong light from fluores-
cent lamps shining onto the remote receiver?
Set the projector up in a location where strong light does not
shine onto the remote receiver.
Are the batteries dead or have the batteries
been inserted correctly?
Make sure the batteries are inserted correctly or replace the bat-
teries with new ones if necessary. s p.22
Has the streaming media player been paired?
•
When the pairing screen is displayed, hold down the Enter button
and the home button on the remote control at the same time for
approximately three seconds to pair the devices. s p.22
•
If the pairing screen is not displayed, make sure that the projector
and the streaming media player are on, and then hold down the
Esc button and the right button on the remote control for ap-
proximately seven seconds. This should display the pairing
screen and allow you to perform pairing. s p.22
Are you using the remote control for Android
TV
TM
to perform operations?
Check that you are not using the remote control for Android
TV
TM
. Use the projector remote control.
Problems with the control panel
Cannot make settings on the control panel
Check Remedy
Is Control Panel Lock set to Full Lock or Par-
tial Lock?
When Control Panel Lock is set to Full Lock in the Configura-
tion menu, all button operations on the control panel are disa-
bled; when Partial Lock is set, only the standby button on the
control panel is available. Perform operations from the remote
control. s Settings - Lock Setting - Control Panel Lock p.63
Troubleshooting
82
Problems with 3D
Cannot project correctly in 3D
Check Remedy
Are the 3D Glasses turned on? Turn on the 3D Glasses.
Are the 3D Glasses fully charged? Charge the 3D Glasses.
Is a 3D image being projected? If the projector is projecting a 2D image, or if an error occurs on
the projector that prevents the 3D image from being projected,
you cannot view 3D images even if you are wearing the 3D
Glasses.
Is the input image in 3D? Check that the input image is 3D compatible.
Since most TV broadcasts do not contain a 3D format signal, 3D
reception must be set manually.
Is 3D Display set to 2D?If 3D Display is set to 2D from the Configuration menu, the pro-
jector does not automatically change to 3D even when a 3D im-
age is input. Set 3D Display to either 3D or Auto. s Signal - 3D
Setup - 3D Display p.62
Is 3D Format set correctly? Unless the 3D format of the AV device and 3D Format of the
projector are the same, part of the image may not be displayed.
Check that the projector's 3D Format setting matches the 3D
format setting for the AV device. s Signal - 3D Setup - 3D For-
mat p.62
Before changing the 3D Format, set 3D Display to 3D.
Are you viewing within the reception range? If the distance between the projector and the 3D Glasses exceed
10 m, the connection may be lost. Move the 3D Glasses closer to
the projector.
Has pairing been performed correctly? See the user's guide supplied with your 3D Glasses and perform
pairing.
Are there any devices that cause radio wave
interference in the vicinity?
When using other devices at the same time with the frequency
band (2.4 GHz) such as Bluetooth communication devices, wire-
less LAN (IEEE802.11b/g), or microwave ovens, radio wave inter-
ference may occur, the image may be interrupted, or communi-
cation may not be possible. Do not use the projector near these
devices.
Problems with HDMI
HDMI Link does not function
Check Remedy
Are you using a cable that meets the HDMI
standards?
Operations are not possible with cables that do not meet the
HDMI standards.
Troubleshooting
83
Check Remedy
Does the connected device meet the HDMI
CEC standards?
If the connected device does not meet the HDMI CEC standards,
it cannot be operated even if it is connected to the HDMI port.
See the documentation and so on supplied with the connected
device for more information.
Also, check if the device is available under Device Connec-
tions from the Configuration menu. s Settings - HDMI Link -
Device Connections p.49
Are the cables connected correctly? Check that all the cables required to use HDMI Link are securely
connected. s p.48
Is the power for the amplifier or DVD recorder
and so on turned on?
Put each device in standby status. See the documentation and
so on supplied with the connected device for more information.
If you have connected a speaker and so on, set the connected
equipment to PCM output.
Was a new device connected, or was the con-
nection changed?
If the CEC function for a connected device needs to be set again,
for example when a new device is connected or the connection
is changed, you may need to restart the device.
Are many multi-media players connected? Up to 3 multi-media players that meet the HDMI CEC standards
can be connected at the same time.
The device name is not displayed under Device Connections
Check Remedy
Does the connected device meet the HDMI
CEC standards?
If the connected device does not meet the HDMI CEC standards,
it is not displayed. See the documentation and so on supplied
with the connected device for more information.
Problems with a streaming media player
Cannot view images from a streaming media player
Check Remedy
Is the streaming media player connected cor-
rectly?
Make sure that the streaming media player is connected cor-
rectly to the HDMI3 port using the HDMI extension cable and the
USB power cable supplied.
Is the device connected to the Internet? You need an Internet connection to view online content. Make
sure you can connect to Wi-Fi.
Network problems
Cannot access the network via wireless LAN
Check Remedy
Is Wireless LAN Power set to Off?Set Wireless LAN Power to On in the Configuration menu. If this
is already set to On, set Wireless LAN Power to Off, and then set
it to On again. s Network - Wireless LAN Power p.68
Troubleshooting
84
Check Remedy
Is the passphrase correct? Note that the passphrase is case sensitive; upper case and lower
case letters are treated as different characters. If you have for-
gotten your passphrase, set it again. s Network - Network
Configuration - Security - Passphrase p.70
Have you checked the Event ID? Check the Event ID number and perform the following steps.
s Info - Projector Info - Event ID p.72
s p.85
The settings cannot be modified using the remote controller function for Epson iProjection
Check Remedy
Is the connected network device turned on? When the projector is in the standby mode with Standby
Mode set to Communication On, check to see if the connected
network device is powered on. After powering on the network
device, try starting the projector again. s Extended - Standby
Mode p.65
The image contains static during network projection
Check Remedy
Are there any obstacles between the access
point and the connected device?
Check for any obstacles between the access point, the mobile
device, the computer, and the projector, and change their posi-
tions to improve communication.
Is the distance between the access point and
the connected device too far?
Make sure that the access point, the mobile device, the comput-
er, and the projector are not too far apart. Move them closer to-
gether and try to connect again.
Are there any Bluetooth devices or micro-
wave oven in the vicinity?
If the wireless connection is slow or your projected image con-
tains noise, check for interference from other equipment, such
as a Bluetooth device or microwave. Move the interfering device
farther away or expand your wireless bandwidth.
Are too many devices connected? Reduce the number of connected devices if the connection
speed declines.
Troubleshooting
85
About Event ID
Check the event ID and perform the remedy given below. If you cannot resolve the problem, contact your
local dealer or the nearest Epson repair center.
s
Epson Projector Contact List
Event ID Cause Remedy
0022
0027
0028
0029
0030
0031
0035
0434
0481
0482
0485
Network communication is unstable. Check the network communication status, and
reconnect after waiting for a while.
0432
0435
Failed to start the network software. Restart the projector.
0433 An image that was transferred cannot be re-
produced.
Restart the network software.
0484 Communications was cut off from the comput-
er.
04FE The network software ended unexpectedly. Check the status of network communications.
Wait for a while and then try connecting again.
0479
04FF
A system error occurred in the projector. Restart the projector.
0891 The same SSID access point cannot be found. Set the computer, the access point, and the
projector to the same SSID.
0892 WPA and WPA2 authentication type mismatch. Check the setting of wireless LAN security to
see if it is correct.
0894 Communications was cut off because a con-
nection was made to the wrong access point.
Check with the network administrator and fol-
low their instructions.
0898 Failed to acquire the DHCP. Check that the DHCP server is operating cor-
rectly. Turn off the DHCP setting if you are not
using DHCP. s Network - Network Configu-
ration - Wireless LAN - IP Settings -
DHCP p.70
0020
0026
0032
0036
0037
0038
0899
Other connection errors If restarting the projector or network software
does not solve the problem, contact your local
dealer or the nearest address provided in the
Epson Projector Contact List. s Epson Projector
Contact List
Maintenance
86
Maintenance
Cleaning the Parts
You should clean the projector if it becomes dirty or if the quality of projected images starts to deteriorate.
Warning
Do not use sprays that contain flammable gas to remove dirt and dust from the projector's lens, air filter,
and so on. The projector may catch fire due to the high internal temperature of the laser.
Cleaning the air filter
Clean the air filter if dust has accumulated on the air filter or when the following message is displayed.
"The projector is overheating. Make sure nothing is blocking the air vent, and clean or replace the air
filter."
Attention
•If dust collects on the air filter, it can cause the internal temperature of the projector to rise, and this can lead
to problems with operation and shorten the optical engine's service life. We recommend cleaning the air filter
every 20,000 hours. Clean them more often than this if using the projector in a particularly dusty environment.
•Do not rinse the air filter in water. Do not use detergents or solvents.
•Lightly brush the air filter to clean it. If it is brushed too strongly, dust will be ground into the air filter and
cannot be removed.
•Do not use an air duster. Combustible material may remain, and dust may enter the precision parts.
a
Press the standby button on the
remote control or the control panel to
turn off the power, and then
disconnect the power cord.
b
Lift the air filter side of the projector
slightly to tilt it.
c
Loosen the fixing screws and open the
air filter cover.
Maintenance
87
d
Remove the air filter.
Grip the knob in the center of the air filter
and pull it out.
e
Hold the air filter with the surface
facing down and tap it 4 or 5 times to
remove the dust.
Turn it over and tap the other side in the
same way.
Attention
If the air filter is hit too hard, it may
become unusable due to deformities
and cracks.
f
Remove any dust remaining on the air
filter by using a vacuum cleaner from
the front side.
Attention
•Do not rinse the air filter in water. Do not
use detergents or solvents.
•Do not use an air duster. Combustible
material may remain, and dust may
enter the precision parts.
g
Install the air filter.
Grip the air filter by the knob in the center
and insert it straight.
h
Close the air filter cover and tighten
the fixing screws.
Maintenance
88
Cleaning the main unit
Before cleaning, make sure you unplug the charging adapter from the outlet.
Clean the projector's surface by wiping it gently with a soft cloth.
If it is particularly dirty, use a piece of well-wrung cloth moistened with water and wipe the surface again with
a dry cloth.
Attention
Do not use detergent for kitchen or volatile substances such as wax, benzine and thinner to clean the
projector's surface. The quality of the outer case may change or the paint may peel off.
Cleaning the lens
Before cleaning, make sure you unplug the charging adapter from the outlet.
Use a commercially available cloth for cleaning glasses to gently wipe off dirt from the lens.
Attention
•Do not rub the lens with harsh materials or handle the lens too roughly as it can easily become damaged.
•Do not use an air duster. Combustible material may remain, and dust may enter the precision parts.
Replacement Periods for Consumables
Air filter replacement period
If the replacement message is displayed even though the air filter has been cleaned
s
p.86
Replacing Consumables
Replacing the air filter
c
Dispose of used air filters properly in accordance with your local regulations.
•Filter frame: Polypropylene
•Filter: Polypropylene
a
Press the standby button on the
remote control or the control panel to
turn off the power, and then
disconnect the power cord.
Maintenance
89
b
Lift the air filter side of the projector
slightly to tilt it.
c
Loosen the fixing screws and open the
air filter cover.
d
Remove the old air filter.
Grip the knob in the center of the air filter
and pull it out.
e
Install the new air filter.
Grip the air filter by the knob in the center
and insert it straight.
f
Close the air filter cover and tighten
the fixing screws.
Maintenance
90
Panel Alignment
Adjusts the pixel color shift of the LCD display. You can adjust the pixels horizontally and vertically by 0.125
pixels within a range of ±3 pixels.
c
•Image quality may decline after performing LCD alignment.
•Images for pixels that extend beyond the edge of the projected screen are not displayed.
a
Press the [Menu] button while
projecting, and then select Display
from Extended.
Remote control Control panel
b
Select Panel Alignment, and then
press the [Enter] button.
c
Enable Panel Alignment.
(1) Select Panel Alignment, and then
press the [Enter] button.
(2) Select On, and then press the [Enter]
button.
(3) Press the [Esc] button to return to the
previous screen.
d
Select the color you want to adjust.
(1) Select Select Color, and then press the
[Enter] button.
(2) Select R (red) or B (blue), and then
press the [Enter] button.
(3) Press the [Esc] button to return to the
previous screen.
e
Select the grid color displayed when
making adjustments from Pattern
Color.
(1) Select Pattern Color, and then press
the [Enter] button.
(2) Select a combination of R (red), G
(green), and B (blue) for the grid color.
R/G/B: Displays a combination all
three colors; red, green and blue. The
actual color of the grid is white.
R/G: This is available when R is selected
from Select Color. Displays a combi-
nation of two colors; red and green.
The actual color of the grid is yellow.
G/B: This is available when B is selected
from Select Color. Displays a combi-
nation of two colors; green and blue.
The actual color of the grid is cyan.
(3) Press the [Esc] button to return to the
previous screen.
Maintenance
91
f
Select Start Adjustments, and then
press the [Enter] button.
First, select Shift the whole panel and
adjust the entire LCD display. When a
confirmation message is displayed, press
the [Enter] button to start the adjustment.
c
The image may become distorted
while adjusting. The image is
restored once adjustments are
complete.
g
Use the up/down/left/right buttons to
adjust, and then press the [Enter]
button.
h
To make more detailed adjustments,
select Adjust the four corners, and
then press the [Enter] button to
confirm the selection.
i
Use the up/down/left/right buttons to
make adjustments, and then press the
[Enter] button to move to the next
adjustment point.
j
When you have adjusted all four
corners, select Exit, and then press the
[Enter] button.
If you feel you still need to make
adjustments after correcting all four points,
select Select intersection and adjust and
then continue making adjustments.
Maintenance
92
Color Uniformity
If colors in the projected image are uneven, you can adjust the color tone of the whole image in Color
Uniformity.
c
The color tone may not be uniform even after performing color uniformity.
a
Press the [Menu] button while
projecting, and then select Display
from Extended.
Remote control Control panel
b
Select Color Uniformity, and then
press the [Enter] button.
The following screen is displayed.
Color Uniformity: Turns color uniformity
on or off.
Adjustment Level: There are eight levels
from white, through gray, and up to black.
You can adjust each level individually.
Start Adjustments: Starts making color
uniformity adjustments.
Reset: Resets all adjustments and settings
for Color Uniformity to their default
values.
c
The image may become distorted
while adjusting Color
Uniformity. The image is restored
once adjustments are complete.
c
Select Color Uniformity, and then
press the [Enter] button.
d
Set this to On, and then press the
[Esc] button.
e
Select Adjustment Level, and then
press the [Enter] button.
f
Use the left and right buttons to set
the adjustment level.
g
Press the [Esc] button to return to the
previous screen.
h
Select Start Adjustments, and then
press the [Enter] button.
i
Select the area you want to adjust, and
then press the [Enter] button.
Adjust the outer areas first, and then adjust
the whole screen.
Maintenance
93
j
Use the up and down buttons to select
the color you want to adjust, and then
use the left and right buttons to adjust.
Press the left button to weaken the color
tone. Press the right button to strengthen
the color tone.
k
Return to step 5 and adjust each level.
l
To complete the adjustment, press the
[Menu] button.
Maintenance
94
About PJLink
PJLink was established by the JBMIA (Japan Business Machine and Information System Industries Association)
as a standard protocol for controlling network-compatible projectors as part of their efforts to standardize
projector control protocols.
This projector complies with the PJLink Class2 standard established by the JBMIA.
The port number used by the search function of PJLink is 4352 (UDP).
You need to make network settings before you can use PJLink. See the following for more information on
network settings.
s
p.68
It supports all commands defined by PJLink Class2 except for the following commands. The compliance is
confirmed by the PJLink standard adaptability verification.
URL: https://pjlink.jbmia.or.jp/english/
•Non-compatible commands
Function PJLink Command
Mute settings Image muting set AVMT 11
Audio muting set AVMT 21
•Correspondence table for port name and source number
Port name Source number
HDMI1 32
HDMI2 33
HDMI3 36
LAN 52
•Manufacturer name displayed for "Manufacture name information query"
EPSON
•Model name displayed for "Product name information query"
EPSON LS500B/LS500W
Appendix
95
Optional Accessories and Consumables
The following optional accessories and consumables are available for purchase if required. This list of optional
accessories and consumables is current as of June 2019. Details of accessories are subject to change without
notice.
Varies depending on country of purchase.
Optional Items
Name Model No. Explanation
Wireless LAN unit ELPAP10 Use when connecting an external device to the pro-
jector via a wireless LAN to project images.
Consumables
Name Model No. Explanation
Air filter ELPAF56 Use as a replacement for used air filters. (1 air filter)
Appendix
96
Supported Resolutions
If the projector receives higher resolution signals than the resolution of the projector panel, the image quality
may be degraded.
The projector supports signals marked with a check symbol.
PC
Signal For-
mat
Resolution
(Dots)
V Sync
(Hz)
Dotclk
(MHz)
HDMI
RGB YCbCr
4:4:4 4:2:2 4:2:0
8
10, 12
8
10, 12
8
10, 12
8
10, 12
VGA60 640 480 60
25.175
Unique Aspect
Signal For-
mat
Resolution
(Dots)
V Sync
(Hz)
Dotclk
(MHz)
HDMI
RGB YCbCr
4:4:4 4:2:2 4:2:0
8
10, 12
8
10, 12
8
10, 12
8
10, 12
21:9 2560 1080 60
198.000
SD
Signal For-
mat
Resolution
(Dots)
V Sync
(Hz)
Dotclk
(MHz)
HDMI
RGB YCbCr
4:4:4 4:2:2 4:2:0
8
10, 12
8
10, 12
8
10, 12
8
10, 12
SDTV (480i)
720 480 59.94
13.500
SDTV (576i)
720 576 50
13.500
SDTV (480p)
720 480 59.94
27.000
SDTV (576p)
720 576 50
27.000
Appendix
97
HD
Signal For-
mat
Resolution
(Dots)
V Sync
(Hz)
Dotclk
(MHz)
HDMI
RGB YCbCr
4:4:4 4:2:2 4:2:0
8
10, 12
8
10, 12
8
10, 12
8
10, 12
HDTV (720p)
1280 720 50
74.250
HDTV (720p)
1280 720 59.94
74.176
HDTV (720p)
1280 720 60
74.250
HDTV (1080i)
1920 1080 50
74.250
HDTV (1080i)
1920 1080 59.94
74.176
HDTV (1080i)
1920 1080 60
74.250
HDTV (1080p)
1920 1080 23.98
74.176
***
HDTV (1080p)
1920 1080 24
74.250
***
HDTV (1080p)
1920 1080 29.97
74.176
***
HDTV (1080p)
1920 1080 30
74.250
***
HDTV (1080p)
1920 1080 50
148.500
***
HDTV (1080p)
1920 1080 59.94
148.352
***
HDTV (1080p)
1920 1080 60
148.500
***
*HDR is supported. (For HDR, HDR10 and HLG are supported.)
4K
Signal For-
mat
Resolution
(Dots)
V Sync
(Hz)
Dotclk
(MHz)
HDMI
RGB YCbCr
4:4:4 4:2:2 4:2:0
8
10, 12
8
10, 12
8
10, 12
8
10, 12
4K
(3840x2160)
3840 2160 23.98
296.703
***
4K
(3840x2160)
3840 2160 24
297.000
***
4K
(3840x2160)
3840 2160 25
297.000
***
4K
(3840x2160)
3840 2160 29.97
296.703
***
4K
(3840x2160)
3840 2160 30
297.000
***
4K
(3840x2160)
3840 2160 50
297.000
*
4K
(3840x2160)
3840 2160 59.94
296.703
*
4K
(3840x2160)
3840 2160 60
297.000
*
Appendix
98
Signal For-
mat
Resolution
(Dots)
V Sync
(Hz)
Dotclk
(MHz)
HDMI
RGB YCbCr
4:4:4 4:2:2 4:2:0
8
10, 12
8
10, 12
8
10, 12
8
10, 12
4K
(3840x2160)
3840 2160 50
594.000
*
4K
(3840x2160)
3840 2160 59.94
593.407
*
4K
(3840x2160)
3840 2160 60
594.000
*
4K(4096x216
0) (SMPTE)
4096 2160 23.98
296.703
***
4K(4096x216
0) (SMPTE)
4096 2160 24
297.000
***
4K(4096x216
0) (SMPTE)
4096 2160 25
297.000
***
4K(4096x216
0) (SMPTE)
4096 2160 29.97
296.703
***
4K(4096x216
0) (SMPTE)
4096 2160 30
297.000
***
4K(4096x216
0) (SMPTE)
4096 2160 50
297.000
*
4K(4096x216
0) (SMPTE)
4096 2160 59.94
296.703
*
4K(4096x216
0) (SMPTE)
4096 2160 60
297.000
*
4K(4096x216
0) (SMPTE)
4096 2160 50
594.000
*
4K(4096x216
0) (SMPTE)
4096 2160 59.94
593.407
*
4K(4096x216
0) (SMPTE)
4096 2160 60
594.000
*
*HDR is supported. (For HDR, HDR10 and HLG are supported.)
3D
Signal For-
mat
Resolution
(Dots)
V Sync
(Hz)
Dotclk
(MHz)
3D Format HDMI
RGB YCbCr
4:4:4 4:2:2
8
10, 12
8
10, 12
8
10, 12
HDTV (720p)
1280 720 60
148.500
Frame Pack-
ing
74.250
Side by Side
74.250
Top and Bot-
tom
Appendix
99
Signal For-
mat
Resolution
(Dots)
V Sync
(Hz)
Dotclk
(MHz)
3D Format HDMI
RGB YCbCr
4:4:4 4:2:2
8
10, 12
8
10, 12
8
10, 12
HDTV (720p)
1280 720 59.94
148.500
Frame Pack-
ing
74.250
Side by Side
74.250
Top and Bot-
tom
HDTV (720p)
1280 720 50
148.500
Frame Pack-
ing
74.250
Side by Side
74.250
Top and Bot-
tom
HDTV (1080i)
1920 1080 60
148.500
Frame Pack-
ing
74.250
Side by Side
74.250
Top and Bot-
tom
HDTV (1080i)
1920 1080 59.94
148.500
Frame Pack-
ing
74.250
Side by Side
74.250
Top and Bot-
tom
HDTV (1080i)
1920 1080 50
148.500
Frame Pack-
ing
74.250
Side by Side
74.250
Top and Bot-
tom
HDTV (1080p)
1920 1080 24
148.500
Frame Pack-
ing
74.250
Side by Side
74.250
Top and Bot-
tom
HDTV (1080p)
1920 1080 23.98
148.500
Frame Pack-
ing
74.250
Side by Side
74.250
Top and Bot-
tom
HDTV (1080p)
1920 1080 60
297.000
Frame Pack-
ing
148.500
Side by Side
148.500
Top and Bot-
tom
Appendix
100
Signal For-
mat
Resolution
(Dots)
V Sync
(Hz)
Dotclk
(MHz)
3D Format HDMI
RGB YCbCr
4:4:4 4:2:2
8
10, 12
8
10, 12
8
10, 12
HDTV (1080p)
1920 1080 59.94
297.000
Frame Pack-
ing
148.500
Side by Side
148.500
Top and Bot-
tom
HDTV (1080p)
1920 1080 50
297.000
Frame Pack-
ing
148.500
Side by Side
148.500
Top and Bot-
tom
Appendix
101
Specifications
EH-LS500W Android TV™ edition/EH-LS500B Android TVTM edition
* The following specifications are current as of June 2019. Details of accessories are subject to change without
notice.
Product name
EH-LS500W Android TV
TM
edition
EH-LS500B Android TV
TM
edition
Appearance
458 (W) x 209.5 (H) x 375 (D) mm
(not including adjustable foot)
Panel Size
0.61"
Display method
Polysilicon TFT active matrix
Resolution
1920 (W) x 1080 (H) x 3
Focus adjustment
Manual
Zoom adjustment
1 - 1.35 (Digital)
Light source
Laser diode
Light source output
Max. 104.5 W
Wavelength of light source
449 - 461 nm
Light source life expectancy*1
Approx. 20,000 hours
Power supply
100 - 240 V AC ±10%, 50/60 Hz, 3.8 - 1.7 A
Power con-
sumption
100 to 120 V area
When operating (when Light Output is 100%): 381 W
When operating (when Light Output is 50%): 236 W
220 to 240 V area
When operating (when Light Output is 100%): 366 W
When operating (when Light Output is 50%): 230 W
Power consumption when
standing by
Communication On: 2.0 W
Communication Off: 0.5 W
Operating altitude
Altitude 0 to 3048 m
Operating temperature*2
+5 to +35°C (No condensation) (at an altitude of 0 to 2286 m)
+5 to +30°C (No condensation) (at an altitude of 2287 to 3048 m)
Storage temperature
-10 to +60°C (No condensation)
Mass
Approx. 9.3 kg
Speaker
10 W x 2
*1 Estimated time until the brightness of the light source is reduced by half.
(Assuming the projector is being used in an environment containing airborne particles of 0.04 to 0.2 mg/m
3
.
This is an approximate guide only and may change depending on the projector's usage and surroundings.)
*2 When using the projector at an altitude of 1,500 m or more, set High Altitude Mode to On to make sure that
the projector's internal temperature is adjusted correctly. s p.65
Appendix
102
Connectors
HDMI port 3 HDMI HDCP2.2 supported, CEC signals supported, 3D sig-
nals supported, Linear PCM supported, Deep Color
USB port
*
1 USB connector (Type A) Supports USB 2.0
DC Out (2.0A) power
supply port
*
1 USB connector (Type A)
Audio Out port 1 Stereo mini jack (3.5Φ)
RS-232C port 1 D-sub 9-pin (male)
LAN port 1 RJ-45
Service port
*
1 USB connector (Type B) Supports USB 2.0
*Not guaranteed to operate all devices that support USB.
This product is also designed for IT power distribution system with phase-to-phase voltage 230V.
Appendix
103
Supplier's DECLARATION of CONFORMITY
According to 47CFR, Part 2 and 15
Class B Personal Computers and Peripherals; and/or
CPU Boards and Power Supplies used with Class B Personal Computers
We: Epson America, Inc.
Located at: 3840 Kilroy Airport Way Long Beach, CA 90806
Tel: 562-981-3840
Declare under sole responsibility that the product identified herein, complies with 47CFR Part 2 and 15 of the
FCC rules as a Class B digital device. Each product marketed, is identical to the representative unit tested and
found to be compliant with the standards. Records maintained continue to reflect the equipment being
produced can be expected to be within the variation accepted, due to quantity production and testing on a
statistical basis as required by 47CFR 2.906. Operation is subject to the following two conditions : (1) this
device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Trade Name: EPSON
Type of Product: LCD Projector
Model: H956C
FCC Compliance Statement
For United States Users
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures.
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
WARNING
The connection of a non-shielded equipment interface cable to this equipment will invalidate the FCC
Certification or Declaration of this device and may cause interference levels which exceed the limits
established by the FCC for this equipment. It is the responsibility of the user to obtain and use a shielded
equipment interface cable with this device. If this equipment has more than one interface connector, do not
leave cables connected to unused interfaces. Changes or modifications not expressly approved by the
manufacturer could void the user's authority to operate the equipment.
Appendix
104
Appearance
Units: mm
205.5 205.5
250 45
Center of lens
227.5
164.8
233
375
209.5
Appendix
105
List of Safety Symbols
The following table lists the meaning of the safety symbols labeled on the equipment.
Symbol mark Approved stand-
ards
Meaning
IEC60417
No. 5007
"ON" (power)
To indicate connection to the mains.
IEC60417
No. 5008
"OFF" (power)
To indicate disconnection from the mains.
IEC60417
No. 5009
Standby
To identify the switch or switch position by means of which part
of the equipment is switched on in order to bring it into the
standby condition.
ISO7000
No. 0434B
IEC3864-B3.1
Caution
To identify general caution when using the product.
IEC60417
No. 5041
Caution, hot surface
To indicate that the marked item can be hot and should not be
touched without taking care.
IEC60417
No. 6042
ISO3864-B3.6
Caution, risk of electric shock
To identify equipment that has risk of electric shock.
IEC60417
No. 5957
For indoor use only
To identify electrical equipment designed primarily for indoor
use.
IEC60417
No. 5926
Polarity of d.c. power connector
To identify the positive and negative connections (the polarity)
on a piece of equipment to which a d.c. power supply may be
connected.
---
IEC60417
No. 5001B
Battery, general
On battery powered equipment. To identify a device for instance
a cover for the battery compartment, or the connector terminals.
IEC60417
No. 5002
Positioning of cell
To identify the battery holder itself and to identify the positioning
of the cell(s) inside the battery holder.
---
IEC60417
No. 5019
Protective earth
To identify any terminal which is intended for connection to an
external conductor for protection against electric shock in case
of a fault, or the terminal of a protective earth electrode.
IEC60417
No. 5017
Earth
To identify an earth (ground) terminal in cases where neither the
symbol is explicitly required.
Appendix
106
Symbol mark Approved stand-
ards
Meaning
IEC60417
No. 5032
Alternating current
To indicate on the rating plate that the equipment is suitable for
alternating current only; to identify relevant terminals.
IEC60417
No. 5031
Direct current
To indicate on the rating plate that the equipment is suitable for
direct current only; to identify relevant terminals.
IEC60417
No. 5172
Class II equipment
To identify equipment meeting the safety requirements specified
for Class II equipment according to IEC 61140.
ISO 3864 General prohibition
To identify actions or operations that are prohibited.
ISO 3864 Contact prohibition
To indicate injury that could occur due to touching a specific part
of the equipment.
--- Never look into the projection lens while the projector is on.
--- To indicate that you must never place anything on the projector.
ISO3864
IEC60825-1
Caution, laser radiation
To indicate the equipment has a laser radiation part.
ISO 3864 Disassembly prohibition
To indicate a risk of injury, such as electric shock, if the equipment
is disassembled.
IEC60417
No. 5266
Standby, partial standby
To indicate that part of the equipment is in the ready status.
ISO3864
IEC60417
No. 5057
Caution, movable parts
To indicate that you must keep away from movable parts ac-
cording to protection standards.
IEC 60417-6056 Caution (movable fan blades)
To indicate that you must keep away from the blades of the mov-
able fan according to protection standards.
IEC 60417-6043 Caution (sharp corners)
To indicate that you must not touch the sharp corners of the
product according to protection standards.
-- Never look into the projection lens while the projector is on.
ISO7010
No. W027
ISO 3864
Warning, light emission (UV, visible light, IR and so on)
To indicate that you must be careful not to injure your eyes or
skin when near light emitting sections.
IEC60417
No.5109
Not to be used in residential areas
To indicate that the electrical equipment/device is not suitable
for use in a residential area.
Appendix
107
Safety Instructions for Laser Products
This projector is a Class 1 laser product that complies with IEC/EN60825-1: 2014. Make sure you follow the
instructions below.
Warning
•Do not open the projector’s case. The projector contains a high-powered laser product.
•Do not look directly into the projector’s light source. The powerful light emitted could cause damage to
eyesight.
•If a problem occurs with the projector, immediately turn off the power, unplug the power plug from the
power outlet, and contact your local dealer or the contact information provided in the Epson Projector Contact
List. Continuing to use the projector when a problem has occurred could not only cause fire or electric shock,
but also damage to eyesight.
Attention
Do not disassemble the projector when disposing of it. Dispose of the projector in accordance with your
country’s regulations or local regulations.
c
•The projector’s light source uses a laser. The laser has the following characteristics.
•The brightness of the light source may be reduced according to the surroundings. The higher the
temperature, the greater the reduction in brightness.
•Light source calibration may be performed when the projector is turned off to correct the white balance
of the light source and changes in the brightness level.
Appendix
108
Laser Warning Labels
This projector comes with internal and external laser warning labels.
Internal
External
As with any bright source, do not stare into the beam, RG2 IEC/EN 62471-5:2015.
Appendix
109
Glossary
This section briefly explains the difficult terms that are not explained in context in the text of this guide. For
details, refer to other commercially available publications.
4K
This provides a high-quality image with a screen comprised of a 3840 x 2160 pixels.
Aspect Ratio
The ratio between an image's length and its height. Screens with a horizontal:vertical ratio
of 16:9, such as HDTV screens, are known as wide screens.
SDTV and general computer displays have an aspect ratio of 4:3.
HDCP
HDCP is an abbreviation for High-bandwidth Digital Content Protection. It is used to pre-
vent illegal copying and protect copyrights by encrypting digital signals sent over DVI and
HDMI ports. Because the HDMI port on this projector supports HDCP, it can project digital
images protected by HDCP technology. However, the projector may not be able to project
images protected with updated or revised versions of HDCP encryption.
HDMI
™
An abbreviation for High Definition Multimedia Interface. This is the standard by which
HD images and multichannel audio signals are digitally transmitted.
HDMI
™
is a standard aimed at digital consumer electronics and computers. By not com-
pressing the digital signal, the image can be transferred at the highest quality possible. It
also provides an encryption function for the digital signal.
HDTV
An abbreviation for High-Definition Television. This refers to high-definition systems
which satisfy the following conditions.
•
Vertical resolution of 720p or 1080i or greater (p = Progressive, i = Interlace)
•
Screen aspect of 16:9 Dolby Digital audio reception and playback (or output)
Interlace
Transmits information needed to create one screen by sending every other line, starting
from the top of the image and working down to the bottom. Images are more likely to
flicker because one frame is displayed every other line.
Pairing
Register devices in advance when connecting with Bluetooth devices to ensure mutual
communication.
SDTV
An abbreviation for Standard Definition Television. This refers to standard television sys-
tems which do not satisfy the conditions for HDTV High-Definition Television.
SVGA
A screen size standard with a resolution of 800 (horizontal) x 600 (vertical) dots.
SXGA
A screen size standard with a resolution of 1,280 (horizontal) x 1,024 (vertical) dots.
VGA
A screen size standard with a resolution of 640 (horizontal) x 480 (vertical) dots.
XGA
A screen size standard with a resolution of 1,024 (horizontal) x 768 (vertical) dots.
YCbCr
In component image signals for SDTV, Y is the brightness, while Cb and Cr indicate the
color difference.
YPbPr
In component image signals for HDTV, Y is the brightness, while Pb and Pr indicate the
color difference.
Appendix
110
General Notes
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted
in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior
written permission of Seiko Epson Corporation. No patent liability is assumed with respect to the use of the
information contained herein. Neither is any liability assumed for damages resulting from the use of the infor-
mation contained herein.
Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties
for damages, losses, costs, or expenses incurred by the purchaser or third parties as a result of: accident, misuse,
or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the
U.S.) failure to strictly comply with Seiko Epson Corporation's operating and maintenance instructions.
Seiko Epson Corporation shall not be liable against any damages or problems arising from the use of any options
or any consumable products other than those designated as Original Epson Products or Epson Approved Prod-
ucts by Seiko Epson Corporation.
The contents of this guide may be changed or updated without further notice.
Illustrations in this guide and the actual projector may differ.
Restriction of Use
When this product is used for applications requiring high reliability/safety such as transportation devices related
to aviation, rail, marine, automotive etc.; disaster prevention devices; various safety devices etc; or functional/
precision devices etc, you should use this product only after giving consideration to including fail-safes and
redundancies into your design to maintain safety and total system reliability. Because this product was not
intended for use in applications requiring extremely high reliability/safety such as aerospace equipment, main
communication equipment, nuclear power control equipment, or medical equipment related to direct medical
care etc, please make your own judgment on this product’s suitability after a full evaluation.
Indication of the manufacturer and the importer in accordance with requirements of directive 2011/65/
EU (RoHS)
Manufacturer: SEIKO EPSON CORPORATION
Address: 3-5, Owa 3-chome, Suwa-shi, Nagano-ken 392-8502 Japan
http://www.epson.com/
Importer: EPSON EUROPE B.V.
Address: Atlas Arena, Asia Building, Hoogoorddreef 5,1101 BA Amsterdam
Zuidoost The Netherlands
http://www.epson.eu/
Appendix
111
General Notice
"EPSON" is a registered trademark of Seiko Epson Corporation. "EXCEED YOUR VISION" is a registered trademark
or trademark of the Seiko Epson Corporation.
iPad, iPhone, Mac ,OS X, and iOS are trademarks of Apple Inc.
Windows and the Windows logo are trademarks or registered trademarks of the Microsoft Corporation in the
United States and/or other countries.
HDMI, the HDMI Logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI
Licensing Administrator, Inc.
The Bluetooth
®
word mark and logo are registered trademarks of Bluetooth SIG, Inc., and the Seiko Epson Cor-
poration uses these marks under license. Other trademarks or trade names are the property of their respective
owners.
Bluetopia
®
is provided for your use by Stonestreet One, LLC
®
under a software license agreement. Stonestreet
One, LLC
®
is and shall remain the sole owner of all right, title and interest whatsoever in and to Bluetopia
®
and
your use is subject to such ownership and to the license agreement. Stonestreet One, LLC
®
reserves all rights
related to Bluetopia
®
not expressly granted under the license agreement and no other rights or licenses are
granted either directly or by implication, estoppel or otherwise, or under any patents, copyrights, mask works,
trade secrets or other intellectual property rights of Stonestreet One, LLC
®
.
© 2000-2012 Stonestreet One, LLC
®
All Rights Reserved.
WPA
™
and WPA2
™
are registered trademarks of the Wi-Fi Alliance.
App Store is a service mark of Apple Inc.
Netflix is a registered trademark of Netflix, Inc..
Google, Android TV
™
, Chromecast, Google Assistant, YouTube and Google Play are trademarks of Google LLC.
"QR Code" is a registered trademark of DENSO WAVE INCORPORATED.
Other product names used herein are also for identification purposes only and may be trademarks of their
respective owners. Epson disclaims any and all rights in those marks.
©SEIKO EPSON CORPORATION 2019. All rights reserved.
Index
112
3
3D brightness ................................................. 62
3D display ......................................................... 62
3D format ......................................................... 62
3D Glasses ........................................................ 46
3D images ........................................................ 45
3D setup ........................................................... 62
4
4K Enhancement ........................................... 61
A
A/V mute .......................................................... 32
Adjusting focus .............................................. 28
Adjusting RGB ................................................. 39
Adjusting the position of the image ...... 29
Advanced .................................................. 61, 63
Air exhaust vent ........................................ 8, 10
Air filter ....................................................... 86, 88
Air filter cover .................................................... 7
Air intake vent ............................................ 7, 10
AMX device discovery .................................. 71
Appearance ................................................... 104
Aspect ......................................................... 33, 62
B
Basic menu ....................................................... 69
Blanking ............................................................ 63
Brightness .......................................... 40, 60, 61
C
Channel ............................................................. 70
Child lock .......................................................... 64
Cleaning the lens ........................................... 88
Cleaning the main unit ................................ 88
Color depth ..................................................... 72
Color format .................................................... 72
Color Mode ...................................................... 33
Color mode ...................................................... 60
Color saturation ............................................. 60
Color Space ...................................................... 62
Color temp. ............................................... 39, 60
Color Uniformity ............................................ 92
Color uniformity ............................................. 66
Configuration menu ..................................... 59
Connecting ...................................................... 18
Connecting a computer .............................. 20
Connecting an ARC compatible AV system
................................................................................ 21
Connecting external speakers .................. 21
Connecting media streaming devices
................................................................................ 18
Connecting to the LAN port ...................... 20
Connecting video equipment ........... 19, 20
Connection mode ......................................... 70
Contrast ............................................................ 60
Control panel .............................................. 7, 11
Control panel lock ......................................... 64
Control4 SDDP ................................................ 71
Cool-down ....................................................... 27
D
Deinterlacing .................................................. 61
Detail Enhancement ..................................... 61
Detail enhancement ..................................... 36
DHCP ........................................................... 70, 71
Direct power on ............................................. 67
Display ............................................................... 66
Display background ..................................... 66
Display LAN info. ........................................... 69
Display the QR code ..................................... 69
Dynamic contrast ................................... 37, 61
Dynamic range ............................................... 62
E
EDID .................................................................... 63
Event ID ............................................................. 85
Extended menu .............................................. 65
F
Focus .................................................................. 78
Focus adjustment .......................................... 28
Focus lever ......................................................... 7
Focus ring ......................................................... 28
Frame interpolation .............................. 37, 61
Front adjustable foot ................................... 10
Front cover ......................................................... 7
Full ...................................................................... 33
G
Gain ............................................................. 39, 60
Gamma ....................................................... 41, 61
Gateway Address ........................................... 71
Gateway address ........................................... 70
G-M Correction ............................................... 60
Grayscale .......................................................... 60
H
H/V-Keystone .................................................. 30
HDMI Link ......................................................... 48
HDMI link .......................................................... 64
Index
113
High altitude mode ...................................... 67
Home screen ............................................ 26, 65
Hue .............................................................. 40, 61
I
Illumination ..................................................... 67
Image ................................................................. 33
Image enhancement ............................. 36, 61
Image menu .................................................... 60
Image processing ................................... 38, 63
Image Shift ....................................................... 63
Image shift ....................................................... 29
Indicators ..................................................... 7, 73
Info menu ......................................................... 72
Inverse 3D glasses ......................................... 62
IP Address ......................................................... 71
IP address ......................................................... 70
IP Address Display ......................................... 71
IP address display .......................................... 70
IP settings ......................................................... 70
K
Keystone ........................................................... 63
Keystone distortion ............................... 30, 63
L
Language ......................................................... 67
Lens ....................................................................... 8
Light output .................................................... 61
Light source info ............................................ 72
Lock setting ..................................................... 64
M
Memory ............................................................. 65
Memory function ........................................... 43
Menu .................................................................. 59
Messages .......................................................... 66
MPEG Noise Reduction ................................ 61
MPEG noise reduction ................................. 36
Mute ................................................................... 32
N
Network menu ............................................... 68
Noise .................................................................. 78
Noise Reduction ............................................. 61
Noise reduction .............................................. 36
O
Offset .......................................................... 39, 60
Operating range ............................................ 23
Operation ......................................................... 67
Others menu ................................................... 71
Overscan ........................................................... 62
P
Pairing ............................................................... 22
Panel Alignment ............................................ 90
Panel alignment ...................................... 66, 68
Passphrase ....................................................... 70
PJLink ................................................................. 94
Power ................................................................. 27
Power supply .............................................. 8, 24
Projection ......................................................... 66
Projection distance ....................................... 17
Projection size ................................................ 28
Projector info .................................................. 72
Projector name ............................................... 69
Projector remote control ............................ 12
Q
Quick Corner ............................................ 31, 63
R
Rear foot ........................................................... 10
Remote control ....................................... 12, 22
Remote control for Android TV ................ 13
Remote password ......................................... 69
Replacing consumables .............................. 88
Reset .............................................. 61, 63, 65, 67
Reset all config ............................................... 72
Reset memory ................................................. 72
Reset menu ...................................................... 72
RGBCMY ..................................................... 40, 61
S
Saturation .................................................. 40, 61
Screen size ....................................................... 17
Search access point ...................................... 70
Security ...................................................... 55, 70
Security menu ................................................ 70
Settings menu ................................................ 63
Sharpness .................................................. 35, 60
Signal menu .................................................... 62
Sleep mode ...................................................... 67
Soft keyboard ................................................. 69
Source ................................................................ 25
Speaker ................................................................ 7
Specifications ............................................... 101
SSID .................................................................... 70
SSID display ..................................................... 70
Standby button ................................................ 7
Standby mode ................................................ 67
Index
114
Startup screen ................................................ 66
Storage space cover ........................................ 7
Subnet Mask .................................................... 71
Subnet mask ................................................... 70
Super-resolution ..................................... 36, 61
Supported resolutions ................................. 96
T
Tint ...................................................................... 60
U
USB power in standby ................................. 67
V
Version .............................................................. 72
Volume ....................................................... 32, 63
W
White balance ................................................. 60
Wired LAN menu ........................................... 71
Wireless LAN menu ....................................... 70
Wireless LAN power ..................................... 68
Wireless LAN unit .......................................... 20
Z
Zoom .................................................... 28, 33, 63