Table of Contents
- Organization of the Guide and Notations in the Guide
- Contents
- Introduction
- Preparing
- Basic Operations
- Projecting Images
- Adjusting the Projected Image
- Displaying the Test Pattern
- Adjusting the Focus
- Adjusting the Projection Size
- Adjust the Height of the Image
- Adjusting the Projector's Tilt
- Adjusting the Position of the Image (Lens Shift)(EH-TW5650/EH-TW5600 only)
- Correcting Distortion
- Adjusting the Volume
- Hiding the Image and Muting the Audio Temporarily(A/V Mute)
- Adjusting the Image
- Useful Functions
- Using the Projector on a Network (EH-TW5650 Only)
- Configuration Menu
- Troubleshooting
- Maintenance
- Appendix
- Index
Epson EH-TW5650 User Manual
Displayed below is the user manual for EH-TW5650 by Epson which is a product in the Data Projectors category. This manual has pages.
Related Manuals
User's Guide
Organization of the Guide and Notations in the Guide
1
Using Each Guide
The guides for this projector are organized as shown below.
Safety Instructions/Support and Service Guide
Contains information on using the projector safely, as well as a support and service guide,
troubleshooting check lists, and so on. Make sure you read this guide before using the pro-
jector.
User's Guide (this guide)
Contains information on setting up and basic operations before using the projector, using
the Configuration menu, and handling problems and performing routine maintenance.
Quick Start Guide
Contains information on the procedures for setting up the projector. Read this first.
Organization of the Guide and Notations in the Guide
2
Notations Used in This Guide
Safety Indications
The documentation and the projector use graphical symbols to show how to use the projector safely.
The following shows the symbols and their meanings. Please understand and respect these caution symbols
in order to avoid injury to persons or property.
Warning
This symbol indicates information that, if ignored, could possibly result in personal injury or even death
due to incorrect handling.
Caution
This symbol indicates information that, if ignored, could possibly result in personal injury or physical
damage due to incorrect handling.
General Information Indications
Attention
Indicates procedures which may result in damage or malfunctions to occur.
c
Indicates additional information and points which may be useful to know regarding a topic.
sIndicates a page where detailed information regarding a topic can be found.
Menu Name Indicates Configuration menu items.
Example: Image - Color Mode
Button Name Indicates the buttons on the remote control or the control panel.
Example: button
About the Use of "This Product" or "This Projector"
As well as the main projector unit, supplied items or optional extras may be referred to using the phrase "this
product" or "this projector".
Contents
3
Organization of the Guide and
Notations in the Guide
Using Each Guide ..................... 1
Notations Used in This Guide ........... 2
Safety Indications.......................2
General Information Indications .............2
About the Use of "This Product" or "This Projector"
..................................... 2
Introduction
Part Names and Functions ............. 6
Front/Top ............................. 6
Control Panel .......................... 7
Remote Control .........................9
Rear ................................ 11
Base ................................ 12
Preparing
Installing ............................ 13
Projected Image and Position of Projector.....13
Installing in parallel with the screen ........ 13
Installing the projector horizontally by
adjusting the height of either side ......... 13
Various Setting Methods.................14
Placing on a table and projecting.........14
Suspending from the ceiling and projecting
.................................. 15
Projection Distance ..................... 15
Connecting a Device ................. 18
Connecting Video Equipment ..............18
Connecting a Computer .................. 18
Connecting Smartphones or Tablets .........18
Connecting USB Devices .................. 19
Connecting External Speakers .............. 19
Connecting Bluetooth
®
devices............20
Preparing the Remote Control ........ 23
Installing the Remote Control Batteries.......23
Remote Control Operating Range ...........24
Operating range (left to right) ............ 24
Operating range (top to bottom) .......... 24
Basic Operations
Projecting Images ................... 25
Turning On the Projector.................25
If the target image is not projected . . . . . . . . 26
Using the Home Screen .................. 26
Turning Off ...........................27
Adjusting the Projected Image . . . . . . . . 28
Displaying the Test Pattern ................ 28
Adjusting the Focus ..................... 28
Adjusting the Projection Size ..............28
Adjust the Height of the Image .............29
Adjusting the Projector's Tilt ...............29
Adjusting the Position of the Image (Lens Shift)
(EH-TW5650/EH-TW5600 only).............29
Correcting Distortion .................... 30
Correct automatically (Auto V-Keystone)
(EH-TW5650/EH-TW5600 only)...........30
Correct manually (H-Keystone adjuster) . . . . . 31
Correct manually (H/V-Keystone) .......... 31
Correct manually (Quick Corner)..........32
Adjusting the Volume ....................33
Hiding the Image and Muting the Audio
Temporarily(A/V Mute) ................... 33
Adjusting the Image
Adjusting the Image ................. 34
Selecting the Projection Quality (Color Mode)
.................................... 34
Switching the Screen Between Full and Zoom
(Aspect).............................35
Adjusting the Sharpness .................. 35
Adjusting Image Resolution (Image
Enhancement) ......................... 35
Setting Auto Iris ........................ 36
Setting Frame Interpolation............... 36
Adjusting the Color .................. 38
Adjusting the Color Temp.................38
Adjusting the RGB (Offset and Gain).........38
Adjusting Hue, Saturation, and Brightness . . . . . 38
Adjusting the Gamma ...................39
Select and adjust the correction value......39
Contents
4
Adjust using the gamma adjustment graph
.................................. 40
Viewing the Image at the Saved Image
Quality (Memory Function) . . . . . . . . . . . 41
Saving a Memory ....................... 41
Loading, Deleting, and Renaming a Memory
.................................... 41
Useful Functions
Enjoying 3D Images .................. 43
Preparing to View 3D Images .............. 43
If the 3D image cannot be viewed .........43
Using 3D Glasses ....................... 44
Charging the 3D Glasses ................44
Pairing 3D Glasses ....................45
Wearing 3D Glasses ...................45
Reading the indicator on the 3D Glasses . . . . 45
Converting 2D Images to 3D ............... 46
Warnings Regarding Viewing 3D Images......47
Using the HDMI Link Function ........ 49
HDMI Link Function ..................... 49
HDMI Link Settings ...................... 49
Connecting ........................... 50
Playing Back Image Data (Slideshow)
...................................... 51
Compatible Data ....................... 51
Playing a Slideshow ..................... 51
Settings for Slideshow ................... 52
Projecting Two Images Simultaneously
(Split Screen) (EH-TW5650 Only) . . . . . . 53
Projecting in Split Screen.................53
Changing the Split Screen Settings ..........53
Exiting Split Screen ..................... 53
Using the Projector on a Network
(EH-TW5650 Only)
Projecting Using Wireless LAN ........ 54
Selecting Network Settings for the Projector
.................................... 54
Selecting the Computer's Wireless LAN Settings
.................................... 56
Selecting wireless network settings in
Windows ........................... 56
Selecting wireless network settings in Mac
.................................. 56
Setting Up Wireless Network Security . . . . . . . . 57
Connecting a Mobile Device Using a QR Code
.................................... 57
Projecting in Screen Mirroring ........ 59
Selecting Screen Mirroring Settings .......... 59
Projecting in Windows 10 ................. 60
Projecting in Windows 8.1 ................61
Projecting Using the Miracast Function.......63
Configuration Menu
Configuration Menu Functions ........ 64
Configuration Menu Operations............ 64
Configuration Menu Table................65
Image menu ........................65
Signal menu ........................ 66
Settings menu ....................... 68
Extended menu ...................... 71
Network menu (EH-TW5650 only)......... 72
Info menu .......................... 76
Reset menu ......................... 76
Troubleshooting
Problem Solving . .................... 77
Reading the Indicators ................... 77
Indicator status during an error/warning....77
Indicator status during normal operation . . . . 79
Wireless LAN indicator and status (EH-
TW5650 only).......................79
When the Indicators Provide No Help........80
Check the problem .................... 80
Problems relating to images ............. 81
Problems when projection starts .......... 84
Problems with the remote control ......... 84
Problems with 3D .................... 84
Problems with HDMI ..................85
Network problems .................... 86
Bluetooth device problems .............. 87
Contents
5
Other problems ...................... 88
About Event ID ........................ 89
Maintenance
Maintenance ........................ 91
Cleaning the Parts ...................... 91
Cleaning the air filter .................. 91
Cleaning the main unit ................. 92
Cleaning the lens ..................... 93
Cleaning the 3D Glasses ................ 93
Replacement Periods for Consumables.......93
Air filter replacement period ............. 93
Lamp replacement period.............. 93
Replacing Consumables .................. 94
Replacing the air filter.................94
Replacing the lamp ...................95
Resetting lamp hours .................. 96
Appendix
Optional Accessories and
Consumables ........................ 98
Optional Items ......................... 98
Consumables .......................... 98
Supported Resolutions ............... 99
Computer Signals (Analog RGB)............99
HDMI1/HDMI2 Input Signal ................ 99
MHL Input Signal ....................... 99
3D Input Signal HDMI ................... 100
3D Input Signal MHL .................... 100
Specifications ...................... 101
Appearance ........................ 103
List of Safety Symbols ............... 104
Glossary ........................... 106
General Notes ...................... 107
General Notice ........................ 108
Introduction
6
Part Names and Functions
Front/Top
Name Function
aLamp cover
Open when replacing the projector's lamp. s p.95
bA/V mute slide lever
Slide the knob to open and close the lens cover.
Close during projection to delete audio and video. s p.33
cAir exhaust vent
Exhaust vent for air used to cool the projector internally.
Warning
Do not look into the air exhaust vent. If the lamp explodes, scattered
small shards of glass and released gas may cause an injury. If any glass
gets into your eyes or mouth, contact your local physicians immediately.
Caution
While projecting, do not put your face or hands near the air exhaust vent,
and do not place objects that may become warped or damaged by heat
near the vent. Hot air from the air exhaust vent could cause burns, warp-
ing, or accidents to occur.
dLens cover
Close when not using the projector to protect the lens from being scratched
or soiled. s p.27
eFoot release lever
Press the foot release lever to extend and retract the front adjustable foot.
s p.29
fLens
Images are projected from here.
gRemote receiver
Receives signals from the remote control. s p.24
hAir intake vent
Intake vent for air used to cool the projector internally.
Introduction
7
Name Function
iAir filter cover
When replacing the air filter, open this cover and remove the air filter. s p.94
jFocus adjuster (EH-
TW5650/EH-TW5600)
Focus ring (EH-TW5400)
Adjusts the image focus. s p.28
kZoom adjuster (EH-
TW5650/EH-TW5600)
Zoom ring (EH-TW5400)
Adjusts the image size. s p.28
lLens shift dial (EH-
TW5650/EH-TW5600
only)
Moves the position of the image vertically. s p.29
mHorizontal keystone ad-
juster
Performs horizontal keystone correction. s p.31
nControl panel
Operates the projector. s p.7
Control Panel
Buttons/Indicators Function
a
Turns the projector on or off. s p.25
Shows the projector's status through a combination of other indicators lit and
flashing. s p.79
b
Operation indicator
Flashes blue to indicate the projector is warming up or cooling down. Shows
the projector's status through a combination of other indicators lit and flashing.
s p.77
c
Shows the access status to the wireless LAN by lighting or flashing. s p.79
EH-TW5600/EH-TW5400 do not light or flash.
d
Flashes orange when it is time to replace the lamp. Shows the projector's errors
through a combination of other indicators lit and flashing. s p.77
Introduction
8
Buttons/Indicators Function
e
Flashes orange if the internal temperature is too high. Shows the projector's
errors through a combination of other indicators lit and flashing. s p.77
f
Switches to the image from each input port. s p.26
g
•
Adjusts the volume. s p.33
You cannot control the volume for Bluetooth audio devices.
•
Selects menu items or adjustment values while displaying the projector's menu.
•
Performs horizontal keystone correction when the Keystone screen is displayed.
s p.31
h
•
Adjusts keystone distortion in projected images. s p.31
•
Selects menu items or adjustment values while displaying the projector's menu.
i
Return to the previous menu level when a menu is displayed. s p.64
j
Selects functions and settings when a menu is displayed. s p.64
k
Displays and closes the Configuration menu.
On the Configuration menu, you can make adjustments and settings for Sig-
nal, Image, Input Signal, and so on. s p.64
l
Displays and closes the Home screen. s p.26
Introduction
9
Remote Control
Button Function
a
Turns the projector on or off. s p.25
b
Switches to the image from each input port.
s p.26
If you press the button when using EH-
TW5650, the source switches between LAN and
Screen Mirroring.
c
•
When HDMI Link is On
Displays the device connections list.
Press other buttons to control playback, stop, or
adjust the volume of connected devices com-
patible with the HDMI CEC or MHL standards.
s p.49
•
When HDMI Link is Off
Displays the HDMI Link settings menu.
d
Displays and closes the Configuration menu.
On the Configuration menu, you can make ad-
justments and settings for Signal, Image, Input
Signal, and so on. s p.64
e
Selects menu items and adjustment values.
s p.64
f
Performs the function assigned to the User But-
ton. s p.68
g
Changes the Color Mode. s p.34
h
Changes the 3D Display to Auto, 3D, or 2D.
s p.46
i
Changes the 3D format. s p.43
j
Sets the Auto Iris. s p.36
k
Displays the Image Enhancement menu.
s p.35
l
Displays and closes the test pattern. s p.28
m
Displays and closes the Home screen. s p.26
Introduction
10
Button Function
n
Turns the video and audio on or off. s p.33
o
Sets the strength for Frame Interpolation.
s p.36
p
Registers and loads a memory. s p.41
q
The adjustment value returns to its default value
when pressed while the menu's adjustment
screen is displayed. s p.64
r
When a menu is displayed, it accepts and enters
the current selection and moves to the next lev-
el. s p.64
s
Returns to the previous menu level when a menu
is displayed. s p.64
t
Adjusts the volume. s p.33
You cannot control the volume for Bluetooth
audio devices.
A
Temporarily mutes or plays the audio. s p.33
Introduction
11
Rear
Name Function
aPower inlet
Connect the power cord. s p.25
bSpeaker
The projector's built-in speaker. Outputs audio.
cRemote receiver
Receives signals from the remote control. s p.24
dAudio Out port
Outputs audio during playback to the external speakers. s p.19
eHDMI2 port
Connects HDMI compatible video equipment and computers. s p.18
fHDMI1/MHL port
Connects HDMI compatible video equipment and computers. s p.18
Also, connects MHL compatible smartphones and tablets. s p.18
gPC port
Connects to the RGB output port on a computer. s p.18
hService port
Service port. This is not normally used.
iUSB port
Connects USB devices such as a USB memory device or a digital camera, and
projects images as a slideshow. s p.18
Introduction
12
Base
Name Function
aCeiling mount fixing
points (three points)
Attaches the optional ceiling mount here when suspending the projector from a
ceiling. s p.98
bSecurity cable fitting
Thread a commercially available theft-prevention wire lock through this opening
to secure and lock the projector.
cRear foot
When set up on a surface such as a table, extend the foot to adjust horizontal tilt.
s p.29
dFront adjustable foot
When set up on a surface such as a table, extend the foot to adjust the height of
the image. s p.29
Preparing
13
Installing
Projected Image and Position of Projector
Install the projector as follows.
Installing in parallel with the screen
If the projector is installed at an angle to the screen, keystone distortion occurs in the projected image.
Adjust the projector's position so that it is installed in parallel with the screen.
c
If the projector cannot be installed in parallel, use one of the following methods to adjust the
projected image.
•Correct distortion in the image using the horizontal keystone adjuster or H/V-Keystone s p.30
•Adjust the position of the projected image using lens shift s p.29
Installing the projector horizontally by adjusting the height of either side
If the projector is tilted, the projected image is also tilted.
Install the projector horizontally so that both sides are at the same height.
If the projector cannot be installed horizontally, you can adjust the projector's tilt with the rear foot.
s
p.29
Preparing
14
Various Setting Methods
Warning
•A special method of installation is required when suspending the projector from a ceiling (ceiling mount). If
it is not installed correctly, it could fall causing an accident and injury.
•If you use adhesives, lubricants, or oil on the ceiling mount fixing points to prevent screws from loosening,
or if you use things such as lubricants or oils on the projector, the projector case may crack causing it to fall
from its ceiling mount. This could cause serious injury to anyone under the projector and also damage the
projector.
•Do not install it on an unstable shelf or in a place out of load range. Otherwise, it could fall or topple causing
an accident and injury.
•When installing it in a high position such as on a shelf, take measures against falling by using wires to ensure
the safety in an emergency, such as an earthquake, and prevent accidents. If it is not installed correctly, it
could fall causing an accident and injury.
•Do not block the air intake vent and air exhaust vent of the projector. Blocking its air intake vent and air
exhaust vent may trap heat inside causing fire.
Attention
•Try not to setup the projector in locations subject to high humidity and dust, or in locations subject to smoke
from fires or tobacco smoke.
•Do not use the projector installed vertically. Doing so could cause a malfunction.
•Clean the air filter once every three months. Clean it more often if the environment is particularly dusty.
s p.91
Placing on a table and projecting
You can install the projector on a table in your living room or on a low shelf to project images.
Preparing
15
Suspending from the ceiling and projecting
You can suspend the projector from the ceiling with the optional ceiling mount to project images.
c
When suspending from the ceiling and projecting, set Projection to Front/Ceiling or Rear/
Ceiling.
s
Extended - Projection p.71
Projection Distance
The size of the projection increases as the projector is moved away from the screen.
Use the table below to setup the projector at the optimum position from the screen. The values given here
are for your reference only.
The maximum lens shift adjustment values are shown in the following table.
c
The projected image becomes smaller after correcting distortion. Increase the projection distance
to fit the projected image to the screen size.
A : Projection distance from the projector to the screen
B : Height from the center of the lens to the bottom edge of the projected image
C : The center of the lens
Preparing
16
EH-TW5650/EH-TW5600
Unit: cm
16:9 Screen Size A B
Minimum (Wide) to Maximum
(Tele)
Vertical Lens Shift Highest to
Lowest
60" 133 x 75 176 to 286 -4 to +7
80" 177 x 100 235 to 382 -5 to +10
100" 221 x 125 295 to 478 -6 to +12
150" 332 x 187 443 to 719 -9 to +19
200" 443 x 249 591 to 959 -12 to +25
250" 553 x 311 740 to 1200 -16 to +31
300" 664 x 374 888 to 1441 -19 to +37
EH-TW5400
Unit: cm
16:9 Screen Size A B*
Minimum (Wide) to Maximum
(Tele)
60" 133 x 75 162 to 195 -7
80" 177 x 100 217 to 261 -9
100" 221 x 125 272 to 327 -11
150" 332 x 187 410 to 492 -17
200" 443 x 249 547 to 658 -23
250" 553 x 311 685 to 823 -28
332" 735 x 413 911 to 1094 -38
* Lens shift is not supported.
Preparing
17
Installation example for EH-TW5650/EH-TW5600 (with 16:9 screen size and 100")
Side view
Overhead view
Preparing
18
Connecting a Device
Attention
•Make cable connections before connecting to a power outlet.
•Check the shape of the cable's connector and the shape of the port, and connect. If you force a connector of
a different shape into the port, it could cause damage and a malfunction to occur.
Connecting Video Equipment
To project images from DVD players and so on, connect to the projector using one of the following methods.
c
•Some types of video equipment are capable of outputting different types of signals. Check the user's
guide supplied with the video equipment to confirm what type of signals can be output.
•If audio is not output correctly, check the settings in Audio Out Device. s Settings - HDMI Link -
Audio Out Device p.68
Connecting a Computer
To project images from a computer, connect the computer using one of the following methods.
When using a commercially available computer cable
When using a commercially available HDMI cable
Connecting Smartphones or Tablets
You can connect MHL compatible smartphones or tablets.
Use a commercially available MHL cable to connect the micro USB port of smartphones and tablets to the
HDMI1/MHL port on the projector.
Preparing
19
The connected smartphone or tablet begins charging when images are projected.
Attention
•Be sure to use an MHL compatible cable for making connections. If a cable that does not meet the MHL
standards is connected, the smartphone or tablet could generate heat, cause a liquid leak, explode or generate
other conditions that could result in a fire.
•If you connect using a commercially available MHL-HDMI conversion adapter, charging the smartphone or
tablet may not work or you may not be able to perform operations using the projector's remote control.
c
•When using a lot of power, such as when playing a movie, you may not be able to charge.
•This projector will not charge devices in standby mode or when the battery in a smartphone or tablet
is depleted.
Connecting USB Devices
You can connect USB devices such as USB memories, and USB compatible digital cameras.
Using the USB cable supplied with the USB device, connect the USB device to the USB (TypeA) port on the
projector.
When the USB device is connected, you can project image files on the USB memory or digital camera as a
slideshow.
s
p.51
When you have finished projecting, remove USB devices from the projector. For devices with a power switch,
make sure you turn them off before disconnecting the USB device.
Attention
•If you use a USB hub, the connection may not operate correctly. Devices such as digital cameras and USB
devices should be connected to the projector directly.
•Connect a digital camera using a USB cable specified for use with the device.
•Use a USB cable less than 3 m in length. If the cable exceeds 3 m, slideshows may not function correctly.
Connecting External Speakers
To output audio from external speakers, connect the speakers to the projector's Audio Out port with a
commercially available audio cable.
Preparing
20
c
•To output audio from external speakers, set Audio Out Device to Projector. s Settings - HDMI
Link - Audio Out Device p.68
•When an AV system is not connected to the projector, audio is output from the external speakers, even
if Audio Out Device is set to AV System.
Connecting Bluetooth® devices
You can connect audio devices that support Bluetooth (A2DP compliant) or 3D Glasses (Bluetooth 3DS Profile
compliant).
See the following for information on connecting 3D Glasses.
s
"Pairing 3D Glasses" p.45
Audio input to the HDMI1 port, HDMI2 port, or Screen Mirroring is output from speakers or headphones that
support Bluetooth.
a
Press the button to display the menu in the following order; Settings - Bluetooth -
Bluetooth Audio.
b
Use the buttons to select On, and then press the button to confirm the
selection.
c
Turn on "pairing mode" on the Bluetooth device you want to connect to.
See the documentation supplied with the Bluetooth device for more information.
d
Select Search Bluetooth Device.
A list of available devices is displayed.
Preparing
21
e
Use the buttons to select the Bluetooth device you want to connect to, and
then press the button to connect.
The next time you turn on the projector, it automatically connects to the last device it connected to.
To switch between the connected devices, repeat the procedure from step 3.
c
•When Audio Out Device is set to AV System, audio cannot be output from Bluetooth audio devices.
To output audio from Bluetooth audio devices, set Audio Out Device to Projector. s Settings -
HDMI Link - Audio Out Device p.68
•There is a delay in the audio output from any Bluetooth audio devices.
Bluetooth specifications
Version
Bluetooth Ver. 3.0
Output
Class 2
Communication dis-
tance
Approx. 10 m
Supported profiles
A2DP
Content protection
SCMS-T
Frequency used
2.4 GHz band (2.402 to 2.480 GHz)
Supported codecs
SBC, Qualcomm
®
aptX
™
audio
Warning
•Electromagnetic interference may cause medical equipment to malfunction. Before using the device, make
sure there is no medical equipment in the vicinity.
•Electromagnetic interference may cause automatically controlled equipment to malfunction which could
cause an accident. Do not use the device near automatically controlled equipment such as automatic doors
or fire alarms.
Preparing
22
c
•Connect a Bluetooth device that supports copyright protection (SCMS-T).
•You may not be able to connect depending on the standard and type of device.
•Even when connecting within the specified communication distance, connections can be lost due to
the status of the signal.
•The communication method for Bluetooth uses the same frequency (2.4 GHz) as wireless LAN
(IEEE802.11b/g) or microwave ovens. Therefore, if these devices are used at the same time, radio wave
interference may occur, the image and audio may be interrupted, or communication may not be
possible. If you do need to use these devices at the same time, make sure there is enough distance
between them and the Bluetooth device.
•You cannot connect multiple Bluetooth devices to the projector at the same time.
Preparing
23
Preparing the Remote Control
Installing the Remote Control Batteries
Attention
•Check the positions of the (+) and (-) marks inside the battery holder to ensure the batteries are inserted the
correct way.
•You cannot use other batteries except for the AA size manganese or alkaline.
a
Remove the battery cover.
While pushing the battery compartment
cover catch, lift the cover up.
b
Replace the old batteries with new
batteries.
Check the polarity of the batteries (+) and
(-) before installing.
c
Reattach the battery cover.
Press the cover until it clicks into place.
c
If delays in the responsiveness of the
remote control occur or if it does not
operate, it probably means that the
batteries are becoming flat. When this
happens, replace them with new
batteries. Have two AA size manganese
or alkaline batteries ready.
Preparing
24
Remote Control Operating Range
Operating range (left to right) Operating range (top to bottom)
Basic Operations
25
Projecting Images
Turning On the Projector
a
Connect the equipment to the
projector.
b
Connect using the power cord
supplied.
c
Press the button on the remote
control or the control panel.
Remote control Control panel
The operation indicator flashes blue as the
projector warms up. Once the projector is
warmed up, the operation indicator stops
flashing and turns blue.
c
When Direct Power On is set to
On, you can start projecting by
simply connecting the power cord
to the projector without having to
press any buttons.
s
Extended -
Operation - Direct Power
On p.71
d
Open the lens cover.
e
Turn on the connected equipment.
Warning
•Do not look into the lens during projection. The
powerful light emitted could cause damage to
eyesight.
•Do not stand in front of the lens during projection.
Clothes could be damaged due to the high
temperature.
Basic Operations
26
c
•This projector provides a Child Lock function to prevent children from accidentally turning the power
on and a Control Panel Lock function to prevent accidental operations and so on. s Settings - Lock
Setting - Child Lock/Control Panel Lock p.68
•This projector provides an Auto Setup function to automatically select the optimum settings when the
input signal for the connected computer image switches. s Signal - Auto Setup p.66
•When using at an altitude of 1500 m or more, set High Altitude Mode to On. s Extended - Operation -
High Altitude Mode p.71
If the target image is not projected
If the image is not projected, you can switch the source using one of the following methods.
Remote control Control panel
Press the button for the target port. Press the button and select the target port.
Press the button to confirm the selection.
Using the Home Screen
The Home screen feature allows you to easily select an image source and access useful functions.
Press the button on the remote control or the control panel to display the Home screen.
Under the following conditions, the Home screen is displayed automatically when the projector is turned on.
•Home Screen Auto Disp. is set to On. s Extended - Home Screen - Home Screen Auto Disp. p.71
•There are no signals from the connected sources.
a
Selects the source you want to project.
b
Displays the connection guide (EH-TW5650 only).
Basic Operations
27
c
Displays the Configuration menu. s p.64
d
Performs menu options assigned to Home Screen in the Extended menu.
s Extended - Home Screen p.71
e
Sets the 3D function. s p.66
f
Changes the Color Mode. s p.34
c
The Home screen disappears after 10 minutes of inactivity.
Turning Off
a
Turn off the connected equipment.
b
Press the button on the remote
control or the control panel.
Remote control Control panel
A confirmation message is displayed.
c
Press the button again.
The operation indicator flashes and the
projector begins to cool down.
d
Wait until cool-down is complete.
When cool-down is complete, the
operation indicator stops flashing.
e
Disconnect the power cord.
c
If the power cord is connected,
some electricity is consumed even
if no operations are made.
f
Close the lens cover.
c
Do not turn the projector back on immediately after turning off the projector. Turning the projector
on/off too frequently can cause the lamp to malfunction.
Basic Operations
28
Adjusting the Projected Image
c
Since images are unstable immediately after the projector is turned on, before you make focus, zoom,
or lens shift settings, we recommend waiting 30 minutes or more after starting to project the images.
Displaying the Test Pattern
When adjusting the zoom/focus or the projection position just after setting up the projector, you can display
a test pattern instead of connecting video equipment.
Press the button on the remote control to display the test pattern. The standard for horizontal lines at
the top and bottom uses 2.40:1 CinemaScope.
Press the button again to end the test pattern display.
Adjusting the Focus
Adjust the focus using the focus ring or the focus adjuster.
Adjusting the Projection Size
Adjust the size of the projected image using the zoom ring or the zoom adjuster.
Basic Operations
29
Adjust the Height of the Image
Press the foot release lever to extend the front adjustable foot. You can tilt the projector up to 11° to adjust
image height.
c
It becomes more difficult to focus the higher the tilt angle is. Use a moderate tilt angle.
Adjusting the Projector's Tilt
If the projected image is horizontally tilted (the left and right sides of the projected image are at different
heights) when the projector is setup on a table, adjust the rear foot so that both sides are level with each other.
Adjusting the Position of the Image (Lens Shift)(EH-TW5650/EH-TW5600 only)
If the projector cannot be installed directly in front of the screen, you can adjust the position of the image by
using lens shift.
Turn the lens shift dial on the projector to adjust the position of the image.
Basic Operations
30
Attention
When using lens shift for adjusting the position of the image, adjust the image by moving it upward.
c
When adjusting the projection position using the lens shift, you are recommended to install the
projector in parallel with the screen.
Correcting Distortion
You can correct keystone distortion using one of the following methods.
Correct automatically
(EH-TW5650/EH-
TW5600 only)
Auto V-Keystone Automatically correct vertical keystone distortion.
Correct manually H-Keystone Adjuster Correct horizontal keystone distortion with the horizontal
keystone adjuster.
H/V-Keystone Manually correct distortion in the horizontal and vertical di-
rections independently.
Quick Corner Adjust the four corners of the projected image individually.
c
•The projected image becomes smaller after correcting distortion. Increase the projection distance to
fit the projected image to the screen size.
•Install the projector parallel with the screen without any loss in image quality. If you cannot install the
projector parallel to the screen, adjust the shape of the image using H/V-Keystone correction.
•When correcting distortion, rotate the lens shift dial to adjust the lens position to the top edge. If the
lens position is incorrect, the projection screen may be warped.
Correct automatically (Auto V-Keystone) (EH-TW5650/EH-TW5600 only)
When the projector is moved or tilted during projection, Auto V-Keystone automatically corrects any vertical
keystone distortion. Two seconds after the projector is moved, it displays an adjustment screen and then
automatically corrects the projected image.
Auto V-Keystone can correct the projected image distortion in these conditions:
•Projection angle is less than 30° up or down.
Basic Operations
31
•Projection is set to Front. s Extended - Projection p.71
c
If you do not want to use the Auto V-Keystone function, set Auto V-Keystone to Off.
s
Settings -
Keystone - Auto V-Keystone p.68
Correct manually (H-Keystone adjuster)
Move the horizontal keystone adjuster to the right or left to perform horizontal keystone correction.
c
•When Keystone is set to Quick Corner, the H-Keystone adjuster does not function. Set it to H/V-
Keystone. sSettings - Keystone p.68
•You can correct images up to 30° left or right.
Correct manually (H/V-Keystone)
You can use the buttons on the control panel to correct keystone distortion.
Press the buttons to display the V-Keystone/H-Keystone gauges.
When the gauges are displayed, press the buttons to perform vertical correction, and press the
buttons to perform horizontal correction.
When the top or bottom is too wide
When the left or right is too wide
c
•You can correct images up to 30° right, left, up, or down.
•You can adjust the volume by pressing the buttons when the gauges are not displayed.
s p.33
•You can set H/V-Keystone from the Configuration menu. s Settings - Keystone - V-Keystone/H-
Keystone p.68
Basic Operations
32
Correct manually (Quick Corner)
You can use the projector's Quick Corner setting to correct the shape and size of an image that is unevenly
rectangular.
a
Press the button to display menus
in the order Settings - Keystone.
Remote control Control panel
b
Use the button to select
Quick Corner, and then press the
button. Press the button again if
necessary.
The area selection screen is displayed.
c
Select the corner you want to correct
using the buttons,
and then press the button.
c
To reset the Quick Corner
corrections, hold down the
button for about two
seconds while the area selection
screen is displayed, and then
select Yes.
d
Use the buttons to
adjust the position of the corner. Press
the button to return to the area
selection screen.
c
If you see this screen, you cannot
adjust the shape any further in
the direction indicated by the
gray triangle.
e
Repeat steps 3 and 4 as needed to
adjust any remaining corners.
f
When you are finished, press the
button.
c
After executing Quick Corner,
the Keystone setting is now set
to Quick Corner in the
projector's Settings menu.
When you press one of the
buttons on the control
panel, the area selection screen
is displayed.
Basic Operations
33
Adjusting the Volume
You can adjust the volume by using the buttons on the remote control or the buttons
on the control panel.
Remote control Control panel
c
•You can also adjust the volume from the Configuration menu. s Settings - Volume p.68
•When an AV System is connected to the projector and you want to adjust the volume for the AV system,
set HDMI Link to On and Audio Out Device to AV System. s Settings - HDMI Link p.68
•You cannot adjust the volume of Bluetooth audio devices from the projector.
Caution
Do not start at high volume.
A sudden excessive volume may cause loss of hearing. Always lower the volume before powering off, so
that you can gradually increase the volume when you next turn on the power.
Hiding the Image and Muting the Audio Temporarily(A/V Mute)
You can temporarily stop projection and mute any sound by pressing the button on the remote control
or by closing the lens cover. To turn the image and sound back on, press the button again or open the
lens cover.
Remote control Main unit
c
•Because a movie continues to play even when it is hidden, you cannot return to the point at which you
hid the image and muted the audio.
•The button also switches between muting and playing the audio.
Adjusting the Image
34
Adjusting the Image
Selecting the Projection Quality (Color Mode)
You can obtain the optimum image quality to suit your surroundings when projecting. The brightness of the
image varies depending on the mode selected.
a
Press the button.
c
•You can make settings from the Configuration menu. s Image - Color Mode p.65
•If you press the button, you can also make settings from the Home screen.s p.26
b
Select Color Mode.
Use the buttons to select a mode, and then press the button to confirm the
selection.
Choices when projecting 2D images
Mode Application
Dynamic
Ideal for use in a bright room.
BrightCinema
Ideal for use in a bright room. Images are clear and sharp.
Natural
Ideal for use in a dark room. We recommend selecting this mode when performing
color adjustment for the image. s p.38
Cinema
Ideal for watching movies and concerts in a dark room.
Choices when projecting 3D images
Mode Application
3D Dynamic
Images are bright and sharper than 3D Cinema.
3D Cinema
Produces crisper colors than 3D Dynamic.
Adjusting the Image
35
Switching the Screen Between Full and Zoom (Aspect)
You can change the Aspect of the projected image.
Press the button to displays menus in the following order.
Signal - Aspect
Use the buttons to select the item, and then
press the button to confirm the selection.
You can select the following aspects according to the input signal from the connected device.
Aspect Mode Explanation
Auto Sets the aspect ratio automatically according to the input signal and Resolution infor-
mation.
Normal Displays the image at the vertical width of the projection area while maintaining the
aspect ratio of the input signal.
Full Displays the image across the entire projection area without maintaining the aspect ratio
of the input signal.
Zoom Displays the image at the width of the projection area while maintaining the aspect ratio
of the input signal.
c
•The Aspect is sometimes fixed by the signal.
•Note that using the aspect ratio function of the projector to reduce, enlarge, or split the projected
image for commercial purposes or for public viewing may infringe upon the rights of the copyright
holder of that image based on copyright law.
Adjusting the Sharpness
You can adjust the outline of the image.
Press the button to displays menus in the following order.
Image - Sharpness
Use the buttons to make adjustments.
The image becomes sharper as the value is increased, and
becomes softer as the value is decreased.
Adjusting Image Resolution (Image Enhancement)
You can adjust the resolution of the image using the Image Enhancement function.
This is only available when receiving input signals from HDMI1, HDMI2, PC, or Screen Mirroring.
The following content can be adjusted.
Image Preset Mode
Select the settings prepared in advance as the settings for Noise Re-
duction, MPEG Noise Reduction, and Detail Enhancement.
Noise Reduction
(Only available when Image Processing is set to Fine) Smoothes out
rough images.
MPEG Noise Reduction
Smoothes out rough images in MPEG format.
Adjusting the Image
36
Detail Enhancement
Enhances the contrast in an image to create a more emphatic texture
and material feel.
Depending on the image, a highlight may be noticeable at the border
between colors. If this bothers you, set a smaller value.
a
Press the button to display menus
in the order Image - Image
Enhancement.
b
Use the buttons to
select the item you want to adjust, and
then press the button to confirm
the selection.
c
Use the buttons to make
adjustments.
Press the button to adjust another item.
Press the button to return the
adjustments to their default values.
d
Press the button to exit the menu.
Setting Auto Iris
By automatically setting the luminance according to the displayed image, you can enjoy deep and rich images.
You can select the luminance adjustment tracking for changes in brightness in the displayed image from
Normal to High Speed.
a
Press the button.
c
You can make settings from the
Configuration menu.
s
Image -
Auto Iris p.65
b
Use the buttons to
select the item, and then press the
button to confirm the selection.
c
Depending on the image, you may hear the Auto Iris operating, but this is not a malfunction.
Setting Frame Interpolation
You can play fast moving images smoothly by automatically producing intermediate frames between the
original frames.
Adjusting the Image
37
Frame Interpolation is available under the following conditions.
•When Image Processing is set to Fine. s Signal - Advanced - Image Processing p.66
•When the source is HDMI1 or HDMI2.
•When inputting 2D signals or 3D signals (1080p 24 Hz). s p.99
a
Press the button.
c
You can make settings from the
Configuration menu.
s
Image -
Frame Interpolation p.65
b
Use the buttons to
select the item, and then press the
button to confirm the selection.
Adjusting the Image
38
Adjusting the Color
Adjusting the Color Temp.
You can adjust the overall tint of the image. Make adjustments if the image is a little too blue or too red and
so on.
Press the button to displays menus in the following order.
Image - Color Temp. - Color Temp.
Use the buttons to make adjustments.
Blue tints grow stronger as the value is increased, and red
tints grow stronger as the value is reduced.
c
Press the button to return the adjustments to their default values.
Adjusting the RGB (Offset and Gain)
You can adjust the brightness of dark areas (Offset) and bright areas (Gain) for R (red), G (green), and B (blue).
Press the button to displays menus in the following order.
Image - Color Temp. - Customized
Use the buttons to select the item, and then
use the buttons to make the adjustments. The image
becomes brighter when moved to the right (positive) and
darker when moved to the left (negative).
Offset
When the image is made brighter, shading for the darker sections is more vividly expressed.
When the image is made darker, the image appears more full-bodied but shading for the
darker sections is harder to distinguish.
Gain
When the image is made brighter, the bright sections become whiter and shading is lost.
When the image is made darker, shading for the bright sections is more vividly expressed.
c
Press the button to return the adjustments to their default values.
Adjusting Hue, Saturation, and Brightness
You can adjust the hue, saturation, and brightness for each of the R (red), G (green), B (blue), C (cyan), M
(magenta), and Y (yellow) colors.
Hue
Adjusts the overall color of the image to be blue, green, or red.
Saturation
Adjusts the overall vividness of the image.
Brightness
Adjusts the overall color brightness of the image.
Adjusting the Image
39
a
Press the button to display menus
in the order Image - Advanced -
RGBCMY.
b
Use the buttons to
select the color you want to adjust,
and then press the button to
confirm the selection.
c
Use the buttons to
select Hue, Saturation, or
Brightness.
d
Use the buttons to make
adjustments.
Press the button to adjust another
color.
Press the button to return the
adjustments to their default values.
e
Press the button to exit the menu.
Adjusting the Gamma
You can adjust slight coloration differences that may occur due to the device being used when the image is
displayed.
You can set it by using one of the following methods.
•Select and adjust the correction value
•Adjust using the gamma adjustment graph
Select and adjust the correction value
a
Press the button to displays menus
in the following order.
Image - Advanced - Gamma
Adjusting the Image
40
b
Use the buttons to
select the correction value, and then
press the button to confirm the
selection.
The larger the value, the lighter the dark
portions of the image become, but bright
areas may appear discolored. The upper
part of the gamma adjustment graph
becomes rounded.
The smaller the value, the darker the bright
portions of the image become. The lower
part of the gamma adjustment graph
becomes rounded.
c
•The horizontal axis of the gamma adjustment graph shows the input signal level, and the vertical axis
shows the output signal level.
•Select Reset to return the adjustments to their default values.
Adjust using the gamma adjustment graph
Select a tone point on the graph and make adjustments.
a
Press the button to displays menus
in the following order.
Image - Advanced - Gamma -
Customized
b
Use the buttons to select the
tone you want to adjust from the
graph.
c
Use the buttons to
adjust the brightness, and then press
the button to confirm the
selection.
Adjusting the Image
41
Viewing the Image at the Saved Image Quality
(Memory Function)
Saving a Memory
You can save the adjustment values for Image from the Configuration menu.
a
Press the button, and then make
the settings for Image that you want
to save.
b
Press the button.
c
Use the buttons to
select Save Memory, and then press
the button to confirm the
selection.
d
Use the buttons to
select the memory name to be saved,
and then press the button to
confirm the selection.
The current projector settings are saved to
the memory.
If the mark on the left of the memory name
is turned aqua, it means the memory has
already been registered. When you select a
registered memory, a message is displayed
asking you to confirm that you want to
overwrite the memory. If you select Yes, the
previous content is erased and the current
settings are saved.
Loading, Deleting, and Renaming a Memory
You can load, delete, and rename registered memories.
Press the button, and then select the target function on the screen displayed.
Function Explanation
Load Memory
Loads the saved memory. When you select a memory and press the
button, the settings applied to the current image are replaced with the
settings from the memory.
Erase Memory
Erases a saved memory. When you select a memory name and press the
button, a message is displayed. Select Yes, and then press the
button to erase the selected memory.
Useful Functions
43
Enjoying 3D Images
Preparing to View 3D Images
Check the following before viewing 3D images.
•The source is HDMI1 or HDMI2.
•Set 3D Display to Auto or 3D.
When 2D is set, press the button on the remote control and switch to Auto or 3D. s Signal - 3D Setup - 3D
Display p.66
•Pair 3D Glasses. s p.45
This projector supports the following 3D formats.
•Frame Packing
•Side by Side
•Top and Bottom
If the 3D image cannot be viewed
The projector automatically projects a 3D image when detecting a 3D format.
Some 3D TV broadcasts may not contain 3D format signals. If this happens, follow the steps below to set the
3D format.
a
Press the button to set 3D
Display to 3D.
The button toggles 3D Display
between Auto, 3D, and 2D.
b
Press the button to set the 3D
format on the AV device.
Useful Functions
44
c
•If you are using a device or cable that does not support 3D images, 3D projection cannot be performed.
•For details on 3D format settings on the AV device, see the documentation supplied with the AV device.
•When the 3D format has not been correctly set up, an image will not be correctly projected as shown
below.
•If a 3D image is not projected correctly even when a 3D format is set, the synchronization timing for
the 3D Glasses may be inversed. Inverse the synchronization timing using Inverse 3D Glasses.
s Signal - 3D Setup - Inverse 3D Glasses p.66
•How a 3D image is perceived varies depending on the individual.
•When you start projecting a 3D image, a warning about viewing 3D images is displayed. You can turn
off this warning by setting 3D Viewing Notice to Off. s Signal - 3D Setup - 3D Viewing Notice p.66
•During 3D projection, the following Configuration menu functions cannot be changed.
Aspect (Normal fixed), Overscan (Off fixed)
•You cannot use the Split Screen function (EH-TW5650 only) during 3D projection.
•How the 3D image is viewed may change depending on the temperature of the surroundings and how
long the lamp has been used. Refrain from using the projector if the image is not projected normally.
Using 3D Glasses
Use the optional 3D Glasses (ELPGS03) to view 3D images.
s
p.98
c
The 3D Glasses come with protective stickers. Remove the protective stickers before use.
Charging the 3D Glasses
Use the USB charging cable to connect the 3D Glasses to the USB Charging Adapter (ELPAC01), and then
connect the USB Charging Adapter to an electrical outlet.
c
•You can only charge the 3D Glasses ELPGS03.
•You can use the glasses for approximately three hours after charging for just three minutes. A full
charge takes 50 minutes and the glasses can be used for approximately 40 hours.
•You can also charge by connecting the 3D Glasses to the projector. When using the projector to charge
the 3D Glasses, connect the USB charging cable to the USB (TypeA) port on the projector (you can only
charge when the projector is turned on).
Useful Functions
45
Attention
•Only connect to an electrical outlet that uses the voltage displayed on the adapter.
•Note the following points when handling the USB cable.
- You should not bend, twist, or pull the cable with too much force.
- You should not modify the cable.
- You should not perform wiring near an electric heater.
- You should not use the cable if it is damaged.
Pairing 3D Glasses
To view 3D images, you first need to pair the 3D Glasses with the projector.
Press the [Pairing] button for a while on the 3D Glasses to start pairing. See the User's Guide for the 3D Glasses
for more information.
c
•When using the 3D Glasses for the first time, pairing is performed when the 3D Glasses are turned on.
You do not need to perform pairing if 3D images can already be viewed correctly.
•Once pairing has been performed, you can view 3D images the next time the devices are turned on.
•You can perform pairing within a range of three meters from the projector. While pairing is being
performed, make sure you stay within a range of three meters from the projector. Otherwise, pairing
will fail.
•If synchronization cannot be performed within 30 seconds, pairing is automatically canceled. When
pairing is cancelled, 3D images cannot be viewed because pairing fails.
Wearing 3D Glasses
a
Turn on the 3D Glasses by sliding the
[Power] switch to On.
The indicator turns on for several seconds,
and then turns off.
b
Put on the 3D Glasses and enjoy the
show.
c
•When you have finished using the
3D Glasses, turn them off by
sliding the [Power] switch to Off.
•If the 3D Glasses are not used for
at least 30 seconds, they turn off
automatically. To turn the 3D
Glasses back on, slide the
[Power] switch to Off, and then
slide it back to On.
Reading the indicator on the 3D Glasses
You can check the status of the 3D Glasses by whether its indicator is lit or flashing.
Useful Functions
46
Indicators Status
Flashes red two times x5 Weak battery
Lit red Charging
Lit green Charging completed
Flashes green and red in turn Pairing
Lit green for ten seconds and then turns
off
Power on or pairing succeeded
Converting 2D Images to 3D
You can convert 2D images from HDMI1 or HDMI2 into 3D images.
a
Press the button to set 3D
Display to Auto.
The button toggles 3D Display
between Auto, 3D, and 2D.
b
Press the button, to display the
menu in the order Signal - 3D Setup
- 2D-to-3D Conversion.
c
Use the buttons to
select the strength of the 3D effect,
and then press the button to
confirm the selection.
Useful Functions
47
Warnings Regarding Viewing 3D Images
Note the following important points when viewing 3D images.
Warning
Disassembling or remodeling
•Do not disassemble or remodel the 3D Glasses.
This could cause a fire to occur or the images to appear abnormal when viewing, causing you to feel unwell.
Storage locations
•Do not leave the 3D Glasses or the supplied parts within reach of children.
They could be accidentally swallowed. If anything is accidentally swallowed, contact a doctor immediately.
Heating
•Do not place the 3D Glasses in a fire, on a heat source, or leave them unattended in a location subject to high
temperatures. Because this device has a built-in rechargeable lithium battery, it could cause burns or a fire if
it ignites or explodes.
Charging
•When charging, connect the supplied cable to the USB port designated by Epson. Do not charge using other
devices as it may cause the battery to leak, overheat, or explode.
•Only use the supplied charging cable to charge the 3D Glasses. Otherwise, it could overheat, ignite, or explode.
Caution
3D Glasses
•Do not drop or press too forcefully on the 3D Glasses.
If the glass sections and so on are broken, an injury could occur. Store the glasses in the soft glasses case.
•Be careful of the edges of the frame when wearing the 3D Glasses.
If it pokes your eye and so on, an injury could occur.
•Do not place your finger in any of the moving sections (such as the hinges) of the 3D Glasses.
Otherwise an injury could occur.
Caution
Wearing 3D Glasses
•Make sure you wear the 3D Glasses correctly.
Do not wear the 3D Glasses upside down.
If the image is not displayed correctly into the right and left eyes, it could cause you to feel unwell.
•Do not wear the glasses unless you are viewing a 3D image.
•How a 3D image is perceived varies depending on the individual. Stop using the 3D function if you feel strange
or cannot see in 3D.
Continuing to view the 3D images could cause you to feel unwell.
•Stop wearing the 3D Glasses immediately if they seem abnormal or a malfunction occurs.
Continuing to wear the 3D Glasses could cause an injury or cause you to feel unwell.
•Stop wearing the 3D Glasses if your ears, nose, or temples become red, painful, or itchy.
Continuing to wear the 3D Glasses could cause you to feel unwell.
•Stop wearing the 3D Glasses if your skin feels unusual when wearing the glasses.
In some very rare cases the paint or materials used in the 3D Glasses could cause an allergic reaction.
Useful Functions
48
Caution
Viewing Time
•When viewing 3D images, always take periodic breaks during extended viewing.
Long periods of viewing 3D images may cause eye fatigue.
The amount of time and frequency of such breaks varies from person to person. If your eyes still feel tired or
uncomfortable even after taking a break from viewing, stop viewing immediately.
Caution
Watching 3D Images
•If your eyes feel fatigued or uncomfortable when viewing 3D images, stop viewing immediately.
Continuing to view the 3D images could cause you to feel unwell.
•When viewing 3D images be sure to always wear 3D Glasses. Do not attempt to view 3D images without 3D
Glasses.
Doing so could cause you to feel unwell.
•Do not place any breakable or fragile objects around you when using 3D Glasses.
3D images may cause you to move your body involuntarily, resulting in damage to nearby items or personal
injury.
•Only wear 3D Glasses when viewing 3D images. Do not move around while wearing 3D Glasses.
Your vision may appear darker than normal, causing you to fall or injure yourself.
•Try to stay as level with the viewing screen as possible when viewing 3D images.
Viewing 3D images at an angle reduces the 3D effect and may cause you to feel unwell due to unintended
color changes.
•If using 3D Glasses in a room with fluorescent or LED lighting, you may see flashing or flickering throughout
the room. If this should occur, reduce the lighting until the flickering goes away or turn off the lights completely
when viewing 3D images. In some very rare cases, this flickering could trigger seizures or fainting for some
individuals. If you begin to feel uncomfortable or unwell at any time when viewing 3D images, stop
immediately.
•Stay at least three times the height of the screen away from the screen when viewing 3D images.
The recommended viewing distance for an 80-inch screen is at least 3 meters, and at least 3.6 meters for a
100-inch screen.
Sitting or standing any closer than the recommended viewing distance may result in eye fatigue.
Caution
Health Risks
•You should not use 3D Glasses if you are sensitive to light, have a heart condition, or are unwell.
Doing so could aggravate your pre-existing conditions.
Caution
Recommended Age of Use
•The minimum recommended age to view 3D images is six years old.
•Children under the age of six are still developing and viewing 3D images may cause complications. Consult
your doctor if you have any concerns.
•Children viewing 3D images through 3D Glasses should always be accompanied by an adult. It is often difficult
to tell when a child is feeling tired or uncomfortable, which could result in them feeling suddenly unwell.
Always check with your child to ensure that they are not experiencing any eye fatigue during viewing.
Useful Functions
49
Using the HDMI Link Function
HDMI Link Function
When an AV device that meets the HDMI CEC standards is connected to the projector's HDMI port, you can
perform linked operations such as linked power on and volume adjustment for the AV system from one
remote control.
c
•As long as the AV device meets the HDMI CEC standards, you can use the HDMI link function even if
the AV system in-between does not meet the HDMI CEC standards.
•Up to 3 multi-media players that meet the HDMI CEC standards can be connected at the same time.
Connection Example
Projector Amplifier Multi-media players and so on
HDMI Link Settings
When HDMI Link is set to On, you can perform the following
operations. s Settings - HDMI Link - HDMI Link p.68
•
Input Change Link
Switches the input source of the projector to HDMI when
content is played back on the connected device.
•
Connected Devices Operations
Using the projector's remote control, you can perform op-
erations such as Play, Stop, Fast Forward, Rewind, Next
Chapter, Previous Chapter, Pause, Volume Adjustment, and
Audio Mute.
You can also select the following functions from the HDMI
Link screen.
Function Explanation
Audio Out Device When an AV system is connected, you can output audio from the projector's speaker
or from the AV system.
Power On Link When Power On Link is set to Bidirectional, operations are linked as shown below.
•
When the projector is turned on, the connected devices are also turned on.
•
Also, when the connected devices are turned on and content is played back, the projector
turns on.
Power Off Link When Power Off Link is set to On, when the projector is turned off, the connected
devices are also turned off.
•
This only works when the connected device's CEC power link function is enabled.
•
Note that depending on the status of the connected device (for example, if it is record-
ing), the device may not power off.
Useful Functions
50
c
To use the HDMI Link function, you must configure the connected device. See the documentation
supplied with the connected device for more information.
Connecting
You can check the connected devices that are available for HDMI Link, and select on the device you want to
project the image from. Devices that can be controlled by HDMI Link automatically become the selected
device.
Before displaying the list of connected devices, check that HDMI Link is set to On.
s
Settings - HDMI
Link - HDMI Link p.68
a
Press the button, and then select
Device Connections.
The Device Connections list is displayed.
Devices that have an aqua icon to their left
are linked by HDMI Link.
If the device name cannot be determined
this field is left blank.
b
Select the device you want to operate
using the HDMI Link function.
c
•If the cable does not meet the HDMI standards, operations are not possible.
•Some connected devices or functions of those devices may not operate properly even if they meet the
HDMI CEC standards. See the documentation and so on supplied with the connected device for more
information.
Useful Functions
51
Playing Back Image Data (Slideshow)
Compatible Data
The following types of files stored on USB storage devices such as USB memories and digital cameras that
are connected to the projector's USB port can be displayed as a slideshow.
Slideshow compatible file types
File Type (Extension) Notes
.jpg
•
Images using CMYK color mode are not compatible.
•
Progressive format images are not compatible.
•
Images with a resolution greater than 8192 x 8192 are not compatible.
•
Due to the characteristics of JPEG files, images may not be projected clearly if the
compression ratio is too high.
Playing a Slideshow
a
Connect a USB storage device.
Files are displayed as thumbnails.
To open a folder, select the folder, and then press the button.
c
If thumbnails of the files are not displayed, press the button on the remote control to
switch the source.
b
Select Slideshow.
Use the buttons to select Slideshow at the bottom right of the screen, and then
press the button.
Slideshow starts.
c
•To close the slideshow, disconnect the USB storage device.
•Select an image from the thumbnails and press the button to enlarge the selected image.
Press the buttons on the remote control when viewing an enlarged image to change between
images. You can also rotate the image using the buttons.
Useful Functions
52
Settings for Slideshow
You can set the file display order and slideshow operations on the option screen.
a
Use the buttons to position the cursor over the folder where you want
to change settings, and then press the button.
The submenu is displayed.
b
Select Option, and then press the button.
The option screen is displayed.
c
Position the cursor over the item you want to change, and press the button to make
settings for each item.
The following table shows the details for each item.
Display Order
You can select to display the files in Name Order or Date Order.
Sort Order
You can select to sort the files In Ascending or In Descending order.
Continuous Play
You can set whether to repeat a slideshow.
Screen Switching
Time
When playing a slideshow, you can set the time for a single file to be dis-
played. You can set a time between No (0) to 60 seconds. When you set No,
auto play is disabled.
Effect
You can set the screen effects when changing slides.
d
When you have finished making settings, use the buttons to position
the cursor over OK, and then press the button.
The settings are applied.
If you do not want to apply the settings, position the cursor on Cancel, and then press the button.
Useful Functions
53
Projecting Two Images Simultaneously (Split
Screen) (EH-TW5650 Only)
Projecting in Split Screen
You can use the split screen feature to simultaneously project two images from different image sources
(HDMI1/HDMI2 and Screen Mirroring).
Check the following points before you start projecting in Split Screen.
•Connect devices to the projector using Screen Mirroring. s p.59
•Make sure the source is HDMI1 or HDMI2.
a
Press the button to display the Settings menu.
b
Select Split Screen, and then press the button.
Images from the HDMI1 or HDMI2 source are projected on the left of the screen, and images from
Screen Mirroring are projected on the right of the screen.
c
3D images cannot be projected in the split screen projection.
Changing the Split Screen Settings
When you press the button while performing the split screen projection, you can change the Split
Screen settings.
The following table shows the details for each item.
Screen Right For-
mat
Select the orientation and size of the image sent by Screen Mirroring.
Audio Source
Select the source to output audio. When Screen Left is selected, audio is
output from the HDMI1 or HDMI2 source. When Screen Right is selected,
audio is output from Screen Mirroring.
Exit Split Screen
Exits the split screen display.
Exiting Split Screen
To exit the split screen projection, press the button.
Using the Projector on a Network (EH-TW5650 Only)
54
Projecting Using Wireless LAN
You can project images from smartphones, tablets, and computers over wireless LAN.
To project over wireless LAN, you need to make wireless network settings for the projector and the connected
device in advance. You do not need to install the wireless LAN unit as this projector has built-in wireless LAN.
Use Epson iProjection to project over wireless LAN. You can download Epson iProjection for free using one
of the following methods; however, any fees incurred when communicating are the responsibility of the
customer.
•Download Epson iProjection (Windows/Mac) from the following Web site.
http://www.epson.com/
•Download Epson iProjection (iOS/Android) from the App Store or Google Play.
Selecting Network Settings for the Projector
Before you can project from your wireless network, you need to select network settings for the projector.
a
Press the button to display menus in the order Network - Wireless LAN Power.
b
Use the buttons to select On, and then press the button.
c
Select Network Configuration, and then press the button.
Using the Projector on a Network (EH-TW5650 Only)
55
d
Select Basic, and then set the following as necessary.
•Projector Name: Enter a name up to 16 alphanumeric characters long to identify the projector over the
network.
•Remote Password: When operating the projector from a smartphone or a tablet, enter a password up to 8
alphanumeric characters long for accessing the projector.
•Display LAN Info.: Set the display format for the projector's network information.
c
Use the displayed keyboard to enter the name, passwords and keyword. Press the
buttons on the remote control to highlight characters, and then press to
enter them.
e
Select Wireless LAN, and then press the button.
f
Select the Connection Mode setting.
•Quick: Lets you quickly connect to one smartphone, tablet, or computer. When you select Quick, go to step 10.
•Advanced: Lets you connect to multiple smartphones, tablets, or computers over a wireless network access
point. When you select Advanced, go to step 7.
When switching the connection mode, follow the on-screen instructions to save your settings. After
saving the settings, the Network menu is displayed.
g
Select Network Configuration - Wireless LAN - Search Access Point, to select the access
point you want to connect to.
h
If you need to assign the SSID manually, select SSID to enter the SSID.
Using the Projector on a Network (EH-TW5650 Only)
56
i
Assign an IP address to the projector as necessary.
•If your network assigns addresses automatically, select IP Settings to set the DHCP setting to On.
•If you need to set addresses manually, select IP Settings to set the DHCP setting to Off, and then enter the
projector's IP Address, Subnet Mask, and Gateway Address as necessary.
j
When you have finished selecting settings, select Complete and then follow the on-screen
instructions to save your settings and exit the menus.
k
Press the button on the remote control. The wireless network settings are complete
when you see the correct IP address on the LAN standby screen.
When you have finished making wireless settings for your projector, you need to make wireless settings on
the connected device. Then start the network software to send images to your projector through a wireless
network.
c
To prevent the SSID and IP address from being displayed on the LAN standby screen or the Home
screen, set SSID Display and IP Address Display to Off.
s
Network - Network Configuration -
Wireless LAN p.72
Selecting the Computer's Wireless LAN Settings
Before connecting to the projector, select the correct wireless network on your computer.
Selecting wireless network settings in Windows
a
To access your wireless utility software, double-click the network icon on the Windows
taskbar.
b
When connecting in Advanced connection mode, select the network name (SSID) of the
network the projector is connecting to.
c
Click Connect.
Selecting wireless network settings in Mac
a
Click the AirPort icon on the menu bar at the top of the screen.
Using the Projector on a Network (EH-TW5650 Only)
57
b
When connecting in Advanced connection mode, make sure AirPort is turned on and select
the network name (SSID) of the network the projector is connecting to.
Setting Up Wireless Network Security
You can set up security for your projector to use on a wireless network. Set up one of the following security
options to match the settings used on your network:
•WPA2 security
•WPA/WPA2 security
a
Press the button to display menus in the order Network - Network Configuration -
Security.
b
Select the security settings to match your network settings.
c
When you have finished making settings, select Complete and follow the on-screen
instructions to save your settings and exit the menus.
Connecting a Mobile Device Using a QR Code
When wireless LAN settings have been completed for the projector, you can read the QR code projected onto
the projection screen by Epson iProjection (V1.3.0 or later) to connect mobile devices such as smartphones
and tablets.
c
When using Epson iProjection in Quick connection mode, we recommend making security settings.
s
p.57
a
Press the button to display the QR code.
c
•
If you press the button, you can also display the QR code from the Home screen.s p.26
•
If the QR code is not displayed, set Display LAN Info. to Text & QR Code from the
Network menu. sNetwork - Network Configuration - Basic - Display LAN Info. p.74
•
To hide the QR code, press the button.
b
Start Epson iProjection on your smartphone or tablet.
Using the Projector on a Network (EH-TW5650 Only)
58
c
Read the projected QR code in Epson iProjection.
Read the code from in front of the screen so that the QR code fits into the guide in your smart phone
or tablet. If you are too far from the screen, the code may not be read.
When a connection is established, select the Contents menu from , and select the file you want to
project.
Using the Projector on a Network (EH-TW5650 Only)
59
Projecting in Screen Mirroring
You can send images to your projector from mobile devices such as laptops, smartphones, and tablets using
Miracast technology.
If your device supports Miracast, you do not need to install any additional software. When using a Windows
computer, make sure that you have the necessary adapter for establishing a Miracast connection.
Note the following limitations when using Screen Mirroring features.
•You cannot play interlaced images.
•You cannot play multi-channel audio over 3ch (channel 3).
•You cannot project images with a resolution above 1920 x 1080 and a frame rate above 30 fps.
•You cannot play 3D video.
•Depending on the device being used, you may not be able to play content that is copyright protected over a
Miracast connection.
•The audio and connection to Bluetooth audio devices may be lost due to radio wave interference.
•Audio may continue to be output from Screen Mirroring even when projecting images from a source other than
Screen Mirroring.
•Do not change the projector's Screen Mirroring Settings during Screen Mirroring projection. Doing so may cause
the projector to disconnect and it may take a while to re-connect.
•While projecting using Screen Mirroring, do not turn off the projector using the power breaker.
c
Mobile devices with Android installed or Windows 8.1 or later installed mainly support Miracast.
Support for Miracast varies depending on the mobile device. See your mobile device manual for
details.
Selecting Screen Mirroring Settings
Select Screen Mirroring Settings on your projector to project images from your mobile device.
a
Press the button to display menus in the order Network - Screen Mirroring.
b
Use the buttons to select On, and then press the button.
Using the Projector on a Network (EH-TW5650 Only)
60
c
Select Screen Mirroring Settings, and then press the button.
d
Select the Display Name settings as necessary.
e
Set the Operation Mode.
•Basic: Connects using the basic settings.
•Extended: Allows you to make detailed connection settings.
f
Set the Adjust Image Quality as necessary.
Select a small number to improve the quality and select large number to increase the speed.
g
When you have selected Extended, make the Extended settings.
•Interrupt Connection: Set this to On to allow other users to switch the screen while projecting in Screen
Mirroring, or select Off to prevent the screen from being switched.
•Channel: Select the wireless channel used in Screen Mirroring.
h
When you finish selecting settings, select Set and follow the on-screen instructions to save
your settings and exit the menus.
Projecting in Windows 10
You can make settings to project images wirelessly from your computer. You can play audio through the
projector's speaker system by connecting using Screen Mirroring.
a
Select Screen Mirroring Settings on your projector as necessary.
Using the Projector on a Network (EH-TW5650 Only)
61
b
Press the button on the remote control to switch to the Screen Mirroring source.
You see the Screen Mirroring standby screen.
c
Display Action Center, and then select Connect.
You see a list of available devices.
d
Select the projector's Display Name from the list.
e
If you see the PIN entry screen on your computer, enter the PIN code displayed on the
Screen Mirroring standby screen or at the bottom right of the projected image.
The projector displays the image from your computer.
c
It may take some time until the connection is established. While connecting, do not disconnect
the projector's power cord. Doing so may cause your device to freeze or malfunction.
Projecting in Windows 8.1
You can set up your computer for wireless projection from Charms in Windows 8.1. You can play audio through
the projector's speaker system by connecting using Screen Mirroring.
a
Select Screen Mirroring Settings on your projector as necessary.
b
Press the button on the remote control to switch to the Screen Mirroring source.
You see the Screen Mirroring standby screen.
Using the Projector on a Network (EH-TW5650 Only)
62
c
On your computer, select Devices from Charms, and then select Project.
d
Select Add a wireless display.
You see a list of available devices.
e
Select the projector's Display Name from the list.
f
If you see the PIN entry screen on your computer, enter the PIN code displayed on the
Screen Mirroring standby screen or at the bottom right of the projected image.
The projector displays the image from your computer.
c
It may take some time until the connection is established. While connecting, do not disconnect
the projector's power cord. Doing so may cause your device to freeze or malfunction.
Using the Projector on a Network (EH-TW5650 Only)
63
Projecting Using the Miracast Function
If your mobile device such as a smartphone supports Miracast, you can connect it to the projector wirelessly
and project images.
You can play audio through the projector's speaker system by connecting using Screen Mirroring.
a
Select Screen Mirroring Settings on your projector as necessary.
b
Press the button on the remote control to switch to the Screen Mirroring source.
You see the Screen Mirroring standby screen.
c
On your mobile device, use your Miracast function to search for the projector.
You see a list of available devices.
d
Select the projector's Display Name from the list.
e
If you see the PIN entry screen on your mobile device, enter the PIN code displayed on the
Screen Mirroring standby screen or at the bottom right of the projected image.
The projector displays the image from your mobile device.
c
It may take some time until the connection is established. While connecting, do not disconnect
the projector's power cord. Doing so may cause your device to freeze or malfunction.
Depending on the mobile device, you may need to delete a device when connecting. Follow
the on-screen instructions on your device.
Configuration Menu
64
Configuration Menu Functions
Configuration Menu Operations
On the Configuration menu, you can make adjustments and settings for Signal, Image, Input Signal, and so on.
a
Press the button.
Remote control Control panel
The Configuration menu is displayed.
b
Use the buttons to
select the top menu on the left, and
then press the button to confirm
the selection.
When you select the top menu on the left,
the sub menu on the right changes.
The line at the bottom is a guide for
operations.
c
Use the buttons to
select the sub menu on the right, and
then press the button to confirm
the selection.
The adjustment screen for the selected
function is displayed.
d
Use the buttons to
adjust the settings.
Ex.) Adjustment bar
Ex.) Choices
Press the button on an item displaying
this icon to change to the selection
screen for that item.
Press the button to return to the
previous level.
e
Press the button to exit the menu.
Configuration Menu
65
c
For items adjusted using an adjustment bar, such as the brightness level, you can press the
button while the adjustment screen is displayed to return the adjustment value to its default value.
Configuration Menu Table
If there is no image signal being input, you cannot adjust items related to the Image or Signal in the
Configuration menu. Note that the items displayed for the Image, Signal, and Info vary depending on the
image signal being projected.
Image menu
Function Menu/Settings Explanation
Color Mode
Dynamic, BrightCinema, Natural, Cinema, 3D Dy-
namic, 3D Cinema
Select a color mode based on your sur-
roundings and the image you are projec-
ting. s p.34
Brightness
Adjusts the brightness when the image
appears too dark.
Contrast
Adjusts the contrast between light and
shade in the images. By increasing the
contrast, the images become vivid.
Color Satura-
tion
Adjusts the color saturation for the im-
ages.
Tint
Adjusts the tint for the images.
Sharpness
Adjusts the image sharpness.
Color Temp.
Color Temp. Adjusts the tint for the images. The image
is tinted blue for high values, and tinted
red for low values.
Customized Adjusts the offset and gain for each R, G,
and B color.
Frame Interpo-
lation*1
Off, Weak, Normal, Strong (This can only be set when Image Pro-
cessing is set to Fine.)
Adjusts the smoothness of movement of
the image.
Image En-
hancement*2
Image Preset Mode Off, Preset 1 to Preset 5 Select the settings prepared in advance as
the settings for Noise Reduction, MPEG
Noise Reduction, and Detail Enhance-
ment.
Noise Reduction (This can only be set when Image Pro-
cessing is set to Fine.)
Smoothes out rough images.
MPEG Noise Reduction Smoothes out rough images in MPEG for-
mat.
Detail Enhancement Creates a more emphatic texture and ma-
terial feel of the image.
Configuration Menu
66
Function Menu/Settings Explanation
Advanced
Gamma 2,1,0,-1,-2 Performs gamma adjustments. You can
select a raw value or adjust the gamma
while viewing the graph. s p.39
Customized
*3
Reset
RGBCMY R/G/B/C/M/Y Hue, Satura-
tion, Bright-
ness
Adjusts the hue, saturation, and bright-
ness for each R, G, B, C, M, and Y color.
s p.38
EPSON Super White On, Off (This is only available when receiving sig-
nal input from the HDMI1 or HDMI2 port.)
Set this to On if you are experiencing
bright over exposure of whites in your im-
age. When set to On, HDMI Video Range
settings are disabled.
Power Con-
sumption
Normal, ECO You can set the lamp brightness to one of
two settings.
Select ECO if the images being projected
are too bright. When ECO is selected, pow-
er consumption during projection decrea-
ses, and fan rotation noise is reduced.
Auto Iris
Off, Normal, High Speed You can change the luminance adjust-
ment tracking for changes in brightness in
the displayed image. s p.36
Reset
Yes, No Resets the adjustment values of Image set
in the current Color Mode to the default
settings.
*1 This is only displayed when a HDMI1 or HDMI2 image signal is being input.
*2 This is only displayed when an HDMI1, HDMI2, PC, or Screen Mirroring image signal is being input.
*3 Settings are saved for each type of input source or Color Mode.
Signal menu
The Signal menu cannot be set when a USB or LAN image signal is being input.
Configuration Menu
67
Function Menu/Settings Explanation
3D Setup*1
3D Display Auto, 3D, 2D To view 3D images, set this to Auto or 3D.
s p.43
3D Format Side by Side, Top
and Bottom
Sets the 3D format for the input signal.
2D-to-3D Conver-
sion
Off, Weak, Medium,
Strong
Converts 2D images to 3D images.
3D Depth -10 to 10 Sets the depth for the 3D image.
Diagonal Screen
Size
60 to 300 Sets the projection size for the 3D image. By
matching this to the actual size, you can achieve
the optimum 3D effect.
3D Brightness Low, Medium, High Sets the brightness for the 3D image.
Inverse 3D Glasses Yes, No Reverses the synchronization timing for the left/
right shutters on the 3D Glasses and the left/right
images. Enable this function if the 3D effect is not
displayed correctly.
3D Viewing Notice On, Off Turns the notice that appears when viewing 3D
content on or off.
Aspect*2
Auto
*1
, Normal, Full
*3
, Zoom
*3
Selects the aspect mode. s p.35
Tracking*2 *3
Varies depending on the input signal. Adjusts computer images when vertical stripes
appear in the images.
Sync.*2 *3
0 to 31 Adjusts computer images when flickering, fuzzi-
ness, or interference appear in the images.
•
Adjusting the Brightness, Contrast, or Sharp-
ness may cause flickering or fuzziness.
•
When adjusting Sync. after adjusting the Track-
ing, you can create a more vivid image.
Position*2 *3
Adjusts the display position up, down, left, and
right when a part of the image is missing so that
the whole image is projected.
Auto Setup*3
On, Off Sets whether or not to automatically adjust the
image whenever the input signal is switched.
When enabled, the Tracking, Position, and
Sync. are automatically configured.
Overscan *2
Auto
*1
, Off, 4%, 8% Changes the output image ratio (the range of the
projected image).
•
Off, 4%, 8%: Sets the range of the image. Off
projects all ranges. Depending on the image sig-
nal, you may notice noise at the top and bottom
of the image.
•
Auto: Automatically sets to Off or 8% depend-
ing on the input signal.
Configuration Menu
68
Function Menu/Settings Explanation
Advanced
HDMI Video
Range
*1
*2
Auto, Normal, Ex-
panded
(This can only be set when EPSON Super
White is set to Off.)
When set to Auto, the video level for the DVD
input signal to the HDMI1 or HDMI2 ports is au-
tomatically detected and set.
If you experience under or overexposure when
set to Auto, set the video level of the projector
to match that of the DVD player's video level.
Your DVD player may be set to Normal or Expand.
Image Process-
ing
*1
*3
*4
Fine, Fast Improves the response speed for images projec-
ted at high-speed, such as games.
Reset
Yes, No Resets all Signal settings except for Diagonal
Screen Size, 3D Viewing Notice, and Aspect.
*1 This is only displayed when a HDMI1 or HDMI2 image signal is being input.
*2 Settings are saved for each type of input source or signal.
*3 This is only displayed when a PC image signal is being input.
*4 This is only displayed when a Screen Mirroring image signal is being input.
Settings menu
Function Menu/Settings Explanation
Keystone
H/V-Keystone V-Keystone -60 to 60 Corrects vertical distortion in an im-
age. s p.31
H-Keystone -60 to 60 Corrects horizontal distortion in an
image. s p.31
Auto V-Keystone
(EH-TW5650/EH-
TW5600 only)
On, Off Enables or disables Auto V-Key-
stone. s p.30
H-Keystone Ad-
juster
On, Off Enables or disables H-Keystone
Adjuster. s p.31
Quick Corner - Selects and adjusts the four corners
of the projected image. s p.32
Split Screen
(EH-TW5650
only)
- The screen is split in two, and im-
ages from the HDMI source and the
Screen Mirroring source are dis-
played.
Volume
0 to 20 Adjusts the volume.
Configuration Menu
69
Function Menu/Settings Explanation
HDMI Link
Device Connections - Displays a list of devices connected
to the HDMI1 or HDMI2 ports.
HDMI Link On, Off Enables or disables the HDMI Link
function.
Audio Out Device Projector, AV System When an AV system is connected,
you can set whether to output audio
from the projector's speaker, or
from the AV system's speaker.
Power On Link Off, Bidirectional, Device -
> PJ, PJ -> Device
Sets the link function when the
power is turned on.
•
When linking operations to the
connected device and turning on
the projector, select Bidirectional
or Device -> PJ.
•
When linking power on for the pro-
jector to the connected device, se-
lect Bidirectional or PJ -> Device.
Power Off Link On, Off Sets whether or not to power off
connected devices when the pro-
jector is turned off.
Bluetooth
Search Bluetooth Device - Searches for available Bluetooth de-
vices and displays them as a list.
Bluetooth Audio On, Off Enables or disables audio output
from Bluetooth audio devices.
Setup cannot be performed in the
following cases.
•
When the source is LAN
•
When Audio Out Device is set to
AV System from the HDMI Link
menu
Connected Device - Displays information on the con-
nected Bluetooth device.
Configuration Menu
70
Function Menu/Settings Explanation
Lock Setting
Child Lock On, Off This locks the button on the
projector's control panel to prevent
children from turning on the pro-
jector by accident. You can turn on
the power when locked by holding
down the button for approxi-
mately three seconds. You can still
turn off the device using the
button, or perform operations with
the remote control as usual.
If changed, this setting is enabled
after you power off the projector
and the cool-down process is com-
plete.
Note that even if Child Lock is set to
On, the projector still turns on when
the power cord is connected if Di-
rect Power On is set to On.
Control Panel Lock Full Lock, Partial Lock, Off Full Lock: Disables all of the projec-
tor's buttons.
Partial Lock: Disables all of the pro-
jector's buttons except for the
button.
is displayed on the screen if but-
tons are pressed while the projector
is locked. To unlock, press and hold
the button on the control panel
for at least 7 seconds.
If changed, this setting is enabled
once you close the Configuration
menu.
User Button
Fine/Fast, 2D-to-3D Conversion, Brightness Control, In-
fo, Display the QR Code (EH-TW5650 only)
Select a Configuration menu item to
assign to the button on the re-
mote control. button, the as-
signed menu item selection/adjust-
ment screen is displayed, allowing
you to make one-touch settings/ad-
justments.
Memory
Load Memory Memory1 to Memory10 Loads the settings saved in Save
Memory to adjust the image.
Save Memory Memory1 to Memory10 Saves the settings made in Image to
a memory.
Erase Memory Memory1 to Memory10 Erases a saved memory.
Rename Memory Memory1 to Memory10,
Default, DVD, VCR, SDTV,
HDTV, Cinema, Sports,
Music, Anime, Game, Cus-
tomized
Changes the saved memory name.
Configuration Menu
71
Function Menu/Settings Explanation
Reset
Yes, No Resets all Settings except for Audio
Out Device, Power On Link, Power
Off Link, User Button, and Memo-
ry.
Extended menu
Function Menu/Settings Explanation
Home Screen
Home Screen Auto
Disp.
On, Off Selects whether or not to display the Home
screen automatically when the projector turns
on. The Home screen is not displayed when the
selected source has an image signal when the
projector turns on.
Custom Function 1 Power Consump-
tion, Auto Iris, Key-
stone, Info
Select the function assigned to the Home screen.
Custom Function 2
Display
Messages On, Off Sets whether or not to display the following mes-
sages (On or Off).
•
Item names for image signals, color modes, and
aspect ratios.
•
If the internal temperature is rising when no im-
age signal is being input or an unsupported sig-
nal is detected.
Display Background Black, Blue, Logo Selects the screen status when no image signal
is being input.
Startup Screen On, Off Sets whether or not to show a startup screen
when projection begins (On or Off). If changed,
this setting is enabled after you power off the
projector and the cool-down process is com-
plete.
Projection
Front, Front/Ceiling, Rear, Rear/Ceiling Change this setting depending on how the pro-
jector is installed.
Configuration Menu
72
Function Menu/Settings Explanation
Operation
Direct Power On On, Off You can set up the projector so that projection
starts as soon as the power cord is plugged in
without any button operations.
Note that when this is set to On, projection starts
if power is restored after a blackout or other
power outage and the power cord is still plugged
into the projector.
Sleep Mode On, Off If no signal is input for the set amount of time, or
if the lens cover is closed for the set amount of
time when the power is on, the projector is au-
tomatically turned off and enters standby mode.
When in standby mode, press the button on
the remote control or the control panel to start
projection.
Sleep Mode Timer 1 to 30 Sets the interval for Sleep Mode.
Illumination On, Off Set this to Off if the light from the indicators on
the control panel bother you when watching a
movie in a dark room.
High Altitude Mode On, Off Set this to On if you are using the projector above
an altitude of 1500 meters.
Auto Source Search On, Off Set to On to detect the input signal automatically
and project images when there is no input signal.
Standby Mode
(EH-TW5650
only)
Communication Off, Communication On Communication On indicates that the projector
can be monitored over a network when the pro-
jector is in standby mode.
Language
- Selects the display language.
Reset
Yes, No Resets all Extended settings except for Projec-
tion, High Altitude Mode, Auto Source
Search, Standby Mode, and Language.
Network menu (EH-TW5650 only)
Function Menu/Settings Explanation
Screen Mirror-
ing
On, Off Enables or disables Screen Mirroring.
Screen Mirror-
ing Info
Display Name, MAC Address, Region
Code, Channel, Connected Device
Displays information on Screen Mirroring.
Configuration Menu
73
Function Menu/Settings Explanation
Screen Mirror-
ing Settings
Display
Name
-(Only available when Screen Mirroring is set to
On.)
Enter a name to identify the projector when
searching for the projector using the Screen Mir-
roring feature.
Operation
Mode
Basic, Extended Select Extended to enable Extended.
Adjust Im-
age Quality
1 (Fine), 2, 3, 4 (Fast) (Only available when Screen Mirroring is set to
On.)
Adjusts the Screen Mirroring speed/quality.
Extended Interrupt
Connection
On, Off (Only available when Extended is set to Exten-
ded.)
Sets whether or not to allow Interrupt Connec-
tion.
Channel 1 to 165 (Only available when Extended is set to Exten-
ded.)
Selects the frequency channel you want to use,
and then stabilizes the connection status.
Reset Yes, No Resets all adjustment values on the Screen Mir-
roring Settings menu to their default settings.
Wireless LAN
Power
On, Off Sets whether or not to use a wireless LAN (On or
Off).
Network infor-
mation - Wire-
less LAN
- Displays the following network settings.
•
Connection Mode
•
Wireless LAN system
•
Antenna Level
•
Projector Name
•
SSID
•
DHCP
•
IP Address
•
Subnet Mask
•
Gateway Address
•
MAC Address
•
Region Code
Display the QR
Code
-(Only available when Wireless LAN Power is set
to On.)
Displays network information for the projector
with a QR code.
Network Con-
figuration
- Displays the screen to set the network. s p.74
Notes on operating the Network menu
Basic operations are made in the same way as when using the Configuration menu.
However, be sure to select the Setup complete menu to save your settings when done.
Configuration Menu
74
Yes:
Saves the settings and exits the Network menu.
No:
Exits the Network menu without saving the settings.
Cancel:
Continues displaying the Network menu.
Soft Keyboard Operations
In the Network menu, the soft keyboard appears when you need to enter numbers and characters. Use the
buttons on the remote control or buttons on the control panel to
select the desired key, and then press the button to enter. Press Finish to confirm your input, or
Cancel to cancel your input.
CAPS key:
Switches between uppercase and lowercase letters.
SYM1/2 key:
Switches the symbol keys.
Basic menu
Function Menu/Settings Explanation
Projector Name
Up to 16 alphanumeric
characters
Enter a name to identify the projector over a network.
Remote Password
Up to 8 alphanumeric
characters
When operating the projector from a smartphone or a tablet,
enter a password for accessing the projector.
Display LAN Info.
Text & QR Code, Text Set the display format for the projector's network information.
Wireless LAN menu
Function Menu/Settings Explanation
Connection Mode
Quick, Advanced Determines how the wireless LAN is connected.
Quick: lets you quickly connect to one smartphone, tablet, or
computer.
Advanced: lets you connect to multiple smartphones, tab-
lets, or computers over a wireless network access point. The
connection is established in infrastructure mode.
Channel
1ch, 6ch, 11ch (This can only be set when Connection Mode is set to Quick.)
Select the frequency bandwidth used by the wireless LAN.
Configuration Menu
75
Function Menu/Settings Explanation
SSID
Up to 32 alphanumeric
characters
(This can only be set when Connection Mode is set to Ad-
vanced.)
Enter an SSID. When an SSID is provided for the wireless LAN
system in which the projector participates, enter the SSID.
Search Access Point
To Search View (This can only be set when Connection Mode is set to Ad-
vanced.)
Search for available wireless network access points.
indicates currently connected access points. indicates
the access points where security is set.
If you select an access point which has security, Security menu
appears. s p.75
IP Settings
(This can only be set
when Connection
Mode is set to Ad-
vanced.)
DHCP Sets whether or not to use DHCP (On or Off). If this is set to
On, you cannot set any more addresses.
IP Address Inputs the IP address for the projector.
The following IP addresses cannot be used.
0.0.0.0, 127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a
number from 0 to 255)
Subnet Mask Inputs the subnet mask for the projector.
The following subnet masks cannot be used.
0.0.0.0, 255.255.255.255
Gateway Address Inputs the gateway IP address of the projector.
The following gateway addresses cannot be used.
0.0.0.0, 127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a
number from 0 to 255)
SSID Display
On, Off Sets whether or not to display the SSID on the LAN Standby
screen and the Home screen (On or Off).
IP Address Display
On, Off Sets whether or not to display the IP address on the LAN
Standby screen and the Home screen (On or Off).
Security menu
Function Menu/Settings Explanation
Security
No, WPA2-PSK, WPA/
WPA2-PSK
Sets the security.
Select WPA2-PSK in Quick and WPA/WPA2-PSK in Ad-
vanced.
Passphrase
From 8 to 32 single-
byte alphanumeric
characters
Inputs the passphrase.
It is recommended to change the passphrase periodically for
the purpose of security.
Reset menu
Function Explanation
Reset network settings.
You can reset all adjustment values for Network to their default settings.
Configuration Menu
76
Info menu
Function Menu/Settings Explanation
Projector Info
Lamp Hours Displays the cumulative lamp operating time.
Source Displays the name of the port to which the current input
source is connected.
Input Signal Displays the input signal setting of the current input source.
Resolution Displays the resolution.
Scan Mode Displays the scan mode.
Refresh Rate Displays the refresh rate.
3D Format Displays the 3D format of the signal input during 3D projec-
tion (Frame Packing, Side by Side, or Top and Bottom).
Sync Info Displays the image signal information.
This information may be needed if service is required.
Color Depth Displays the color depth.
Status This is information about problems that have occurred on the
projector.
This information may be needed if service is required.
Serial Number Displays the projector's serial number.
Event ID The application error log appears. s p.89
Version
Main Displays the firmware version of the projector.
Video2
Screen Mirroring
Reset menu
Function Explanation
Reset Lamp Hours
Resets the cumulative lamp hours use time to 0 H. Reset when you replace the
lamp.
Reset Memory
Resets all items for Memory to their default settings.
Reset All
Resets all items in the Configuration menu to their default settings.
The following items are not reset to their defaults: Memory, Lamp Hours, Lan-
guage, and all adjustment values for the Network menu.
Troubleshooting
77
Problem Solving
Reading the Indicators
You can check the status of the projector from the flashing and lit , (operation indicators),
o
,
m
, and
on the control panel.
Refer to the following table to check the projector's status and how to remedy problems shown by the
indicators.
Indicator status during an error/warning
: Flashing : Lit : Status maintained : Off
Indicators Status Remedy
(blue)
(orange)
Replace Lamp
It is time to replace your lamp. Replace the lamp with a new lamp
as soon as possible. s p.95
The lamp may explode if you continue to use it in this status.
(blue)
(orange)
High Temp Warning
You can continue projecting. If the temperature rises too high
again, projection stops automatically.
•
If the projector is installed next to a wall, make sure there is at
least 20 cm between the wall and the projector's exhaust vent.
•
If the air filter is clogged, clean it. s p.91
Troubleshooting
78
Indicators Status Remedy
(blue)
(orange)
Internal Error
The projector has malfunctioned.
Remove the power plug from the electrical outlet, and contact
your local dealer or the nearest Epson repair center. s Epson
Projector Contact List
(blue)
(orange)
Fan Error
Sensor Error
(blue)
(orange)
Auto Iris Error
(blue)
(orange)
Power Err. (Ballast)
(blue)
(orange)
Lamp Error
Lamp Failure
Lamp Cover Open
There is a problem with the lamp, or it failed to turn on.
•
Disconnect the power cord, and then check if the lamp is cracked.
s p.95
If it is not cracked, reinstall the lamp and turn on the power.
If reinstalling the lamp does not fix the problem, or if the lamp is
cracked, remove the power plug from the electrical outlet, and
contact your local dealer or the nearest Epson repair center.
s Epson Projector Contact List
•
Check that the lamp cover has been properly closed.
Troubleshooting
79
Indicators Status Remedy
(blue)
(orange)
High Temp Error
(Overheating)
The internal temperature is too high.
•
The lamp turns off automatically and projection stops. Wait for
about five minutes. When the fan has stopped, disconnect the
power cord.
•
If the projector is installed next to a wall, make sure there is at
least 20 cm between the wall and the projector's exhaust vent.
•
If the air filter is clogged, clean it. s p.91
•
When using at an altitude of 1500 m or more, set High Altitude
Mode to On. s Extended - Operation - High Altitude
Mode p.71
•
If turning the power back on does not clear the problem, stop
using the projector and remove the power plug from the elec-
trical outlet. Contact your local dealer or the nearest Epson repair
center. s Epson Projector Contact List
Indicator status during normal operation
: Flashing : Lit : Off
Indicators Status Remedy
(blue)
Standby condition
When you press the button on the remote control or the
control panel, projection starts after a short wait.
(blue)
Warm-up in progress
Warm-up time is about 30 seconds.
The power-off operation is disabled while the projector is warm-
ing-up.
Cool-down in pro-
gress
All operations are disabled while the projector is cooling-down.
The projector enters standby condition when cool-down is com-
plete. If for any reason the power cord is disconnected during
cool-down, wait until the lamp has cooled down sufficiently
(about 10 minutes), reconnect the power cord, and then press
the button on the remote control or the control panel.
(blue)
Projection in pro-
gress
The projector is operating normally.
c
•Under normal operating conditions, the o and m indicators are off.
•When the Illumination function is set to Off, all indicators are off under normal projection conditions.
s Extended - Operation - Illumination p.71
Wireless LAN indicator and status (EH-TW5650 only)
: Flashing : Lit : Off
Troubleshooting
80
Indicators Status Explanation
(blue)
Ready
Wireless LAN is available.
(Flashing blue
quickly)
Connecting
Connecting to a device.
(Flashing blue
slowly)
Error
Wireless LAN error. Select Off as the Wireless LAN Power setting
in the projector's Network menu, and select On again.
If you cannot solve the problem, contact the following address.
s Epson Projector Contact List
Starting
Wireless LAN Off
Wireless LAN connection is unavailable. Check that Wireless
LAN Power is set to On in the Network menu.
When the Indicators Provide No Help
Check the problem
Check the following table to see if your problem is mentioned, and go to the appropriate page for information
on handling the problem.
Problem Page
Problems relating to im-
ages
No images appear.
Projection does not start, the projection area is completely black, or
the projection area is completely blue.
p.81
Moving images being projected from a computer are not projected. p.81
"Not supported" is displayed. p.82
"No Signal" is displayed p.82
Images are fuzzy or out of focus. p.82
Interference or distortion appears in the images. p.82
The image is truncated (large) or small, or only a part of the image is
projected.
p.83
Image colors are not right.
The whole image appears purplish or greenish, images are black &
white, or colors appear dull.
*
p.83
Images appear dark. p.83
Projection stops automatically. p.84
Problems when projection
starts
The projector does not turn on. p.84
Problems with the remote
control
The remote control does not respond. p.84
Problems with 3D Cannot project correctly in 3D. p.84
Troubleshooting
81
Problem Page
Problems with HDMI HDMI Link does not function. p.85
The device name is not displayed under device connections. p.86
Network problems Cannot access the network via wireless LAN. p.86
The image contains static during network projection. p.86
Cannot connect using Screen Mirroring. p.87
The image contains static during Screen Mirroring connection. p.87
Bluetooth device prob-
lems
Cannot connect Bluetooth device. p.87
The audio and connection for the Bluetooth device disconnects. p.88
Other problems No audio, or the audio is too low. p.88
Cannot make settings on the control panel. p.88
Slideshow does not start. p.89
*Because color reproduction differs between monitors and computer LCD screens, the image projected by the
projector and the color tones displayed on the monitor may not match, however this is not a fault.
Problems relating to images
No images appear
Check Remedy
Is the projector turned on? Press the button on the remote control or the control panel.
Is the power cord connected? Connect the power cord.
Are the indicators switched off? Disconnect and then reconnect the projector's power cord.
Check that pressing the power button after connection supplies
the projector with power.
Is an image signal being input? Check that the connected device is turned on. When Messag-
es is set to On from the Configuration menu, image signal mes-
sages are displayed. s Extended - Display - Messages p.71
Are the Configuration menu settings correct? Reset all of the settings. s Reset - Reset All p.76
(Only when projecting computer image sig-
nals)
Was the connection made while the power of
the projector or the computer was already
turned on?
If the connection is made while the power is already turned on,
the Fn key (Function key) that switches the computer's image
signal to external output may not work. Turn off the power for
the computer and the projector and then turn it back on again.
Moving images are not displayed
Check Remedy
(Only when projecting computer image sig-
nals)
Is the computer's image signal set to external
output and to output to the LCD monitor at
the same time?
Depending on the computer's specifications, moving images
may not be displayed when the computer is set to external out-
put and to the LCD monitor output at the same time.
Switch it so that the image signal is set to external output only.
For the computer's specifications, see the documentation sup-
plied with the computer.
Troubleshooting
82
"Not supported" is displayed
Check Remedy
(Only when projecting computer image sig-
nals)
Do the image signal's frequency and resolu-
tion correspond to the mode?
Check the image signal being input in Resolution from the Con-
figuration menu, and check that it corresponds to the projector's
resolution. s About - Projector Info p.76
s p.99
"No Signal " is displayed
Check Remedy
Are the cables connected correctly?Check that all the cables required for projection are securely
connected. s p.18
Is the correct image input port selected? Switch the image with the source buttons on the remote control,
or the button on the control panel. s p.26
Is the connected device turned on? Turn on the device.
(Only when projecting computer image sig-
nals)
Are the image signals being output to the
projector?
Switch it so that the image signal is set to external output, and
not just the computer's LCD monitor. For some models, when
the image signals are output externally, they no longer appear
on the LCD monitor.
For the computer's specifications, see the documentation sup-
plied with the computer.
If the connection is made while the power of the projector or the
computer is already turned on, the Fn key (Function key) that
switches the computer's image signal to external output may not
work. Turn the power for the computer and the projector off and
then back on again.
Images are fuzzy or out of focus
Check Remedy
Has the focus been adjusted? Adjust the focus. s p.28
Is the lens cover closed? Open the lens cover. s p.25
Is the projector at the correct distance? Check the recommended projection range. s p.15
Has condensation formed on the lens? If the projector is suddenly taken from a cold environment to a
warm environment, or if sudden ambient temperature changes
occur, condensation may form on the surface of the lens, and this
may cause the images to appear fuzzy. Set the projector up in
the room about one hour before it is used. If the projector is wet
from condensation, turn off the projector, disconnect the power
cord, and leave it for a while.
Interference or distortion appear in images
Check Remedy
Are the cables connected correctly?Check that all the cables required for projection are securely
connected. s p.18
Troubleshooting
83
Check Remedy
Is an extension cable being used? If an extension cable is used, electrical interference may affect
the signals.
(Only when projecting computer image sig-
nals)
Are the Sync. and Tracking settings adjusted
correctly?
The projector uses automatic adjustment functions to project at
the optimum status. However, depending on the signal, some
may not be adjusted correctly even after performing self correc-
tions. If this happens, adjust the Tracking and Sync. settings
from the Configuration menu. s Signal - Tracking/Sync. p.66
(Only when projecting computer image sig-
nals)
Is the correct resolution selected?
Set the computer so that the signals being output are compatible
with the projector. s p.99
Part of the image is truncated (large) or small
Check Remedy
Is the correct Aspect selected? Select the aspect mode to match the input signal in Aspect from
the Configuration menu. s Signal - Aspect p.66
Is the image Position adjusted correctly? Adjust the Position setting from the Configuration menu.
s Signal - Position p.66
(Only when projecting computer image sig-
nals)
Is the correct resolution selected?
Set the computer so that the signals being output are compatible
with the projector. s p.99
Image colors are not right
Check Remedy
Is the contrast adjusted correctly? Adjust the Contrast setting from the Configuration menu.
s Image - Contrast p.65
Is the color adjusted correctly? Adjust the Advanced setting from the Configuration menu.
s Image - Advanced p.65
Images appear dark
Check Remedy
Is the image brightness set correctly? Adjust the Brightness setting from the Configuration menu.
s Image - Brightness p.65
Is the contrast adjusted correctly? Adjust the Contrast setting from the Configuration menu.
s Image - Contrast p.65
Is it time to replace the lamp? When the lamp is nearly ready for replacement, the images be-
come darker and the color quality becomes poorer. When this
happens, replace the lamp with a new lamp. s p.95
Troubleshooting
84
Projection stops automatically
Check Remedy
Is Sleep Mode enabled? If the set time is exceeded and no signal is input, the lamp is
automatically turned off and the projector enters standby mode.
The projector returns from standby mode when you press the
button on the remote control or the control panel. If you want
to disable Sleep Mode, change the setting to Off. s Exten-
ded - Operation - Sleep Mode p.71
Problems when projection starts
The projector does not turn on
Check Remedy
Is the power turned on? Press the button on the remote control or the control panel.
Is Child Lock set to On? When Child Lock is set to On from the Configuration menu, hold
down the button on the control panel for approximately
three seconds, or perform operations from the remote control.
s Settings - Lock Setting - Child Lock p.68
Do the indicators turn on and off when the
power cord is touched?
Turn off the projector, and then disconnect and reconnect the
projector's power cord. If the problem continues, stop using the
projector, remove the power plug from the electrical outlet, and
contact your local dealer or the nearest projector information
center. s Epson Projector Contact List
Problems with the remote control
The remote control does not respond
Check Remedy
Is the remote control light-emitting area
pointing towards the remote receiver on the
projector during operation?
Point the remote control towards the remote receiver. Also,
check the operating range. s p.24
Is the remote control too far from the projec-
tor?
Check the operating range. s p.24
Is direct sunlight or strong light from fluores-
cent lamps shining onto the remote receiver?
Set the projector up in a location where strong light does not
shine onto the remote receiver.
Are the batteries dead or have the batteries
been inserted correctly?
Make sure the batteries are inserted correctly or replace the bat-
teries with new ones if necessary. s p.23
Problems with 3D
Cannot project correctly in 3D
Check Remedy
Are the 3D Glasses turned on? Turn on the 3D Glasses.
Troubleshooting
85
Check Remedy
Is a 3D image being projected? If the projector is projecting a 2D image, or if an error occurs on
the projector that prevents the 3D image from being projected,
you cannot view 3D images even if you are wearing the 3D
Glasses.
Is the input image in 3D? Check that the input image is 3D compatible.
Since most TV broadcasts do not contain a 3D format signal, 3D
reception must be set manually.
Is 3D Display set to 2D?If 3D Display is set to 2D from the Configuration menu, the pro-
jector does not automatically switch to 3D even when a 3D image
is input. Press the button, and then set 3D Display to 3D
or Auto. s Signal - 3D Setup - 3D Display p.66
Is 3D Format set correctly? Unless the 3D format of the AV device and 3D Format of the
projector are the same, part of the image may not be displayed.
Check that the projector's 3D Format setting matches the 3D
format setting for the AV device. s Signal - 3D Setup - 3D For-
mat p.66
When changing the 3D Format, set 3D Display to Auto, and
then press the button.
Are you viewing within the reception range? If the distance between the projector and the 3D Glasses exceed
10 m, the connection may be lost. Move the 3D Glasses closer to
the projector.
Has pairing been performed correctly? See the User's Guide for the 3D Glasses to perform pairing.
Are there any devices that cause radio wave
interference in the vicinity?
When using other devices at the same time with the frequency
band (2.4 GHz) such as Bluetooth communication devices, wire-
less LAN (IEEE802.11b/g), or microwave ovens, radio wave inter-
ference may occur, the image may be interrupted, or communi-
cation may not be possible. Do not use the projector near these
devices.
Problems with HDMI
HDMI Link does not function
Check Remedy
Are you using a cable that meets the HDMI
standards?
Operations are not possible with cables that do not meet the
HDMI standards.
Does the connected device meet the HDMI
CEC standards?
If the connected device does not meet the HDMI CEC standards,
it cannot be operated even if it is connected to the HDMI port.
See the documentation and so on supplied with the connected
device for more information.
Also, press the button, and then check if the device is
available under Device Connections. s p.50
Are the cables connected correctly? Check that all the cables required to use HDMI Link are securely
connected. s p.49
Is the power for the amplifier or DVD recorder
and so on turned on?
Put each device in standby status. See the documentation and
so on supplied with the connected device for more information.
If you have connected a speaker and so on, set the connected
equipment to PCM output.
Troubleshooting
86
Check Remedy
Was a new device connected, or was the con-
nection changed?
If the CEC function for a connected device needs to be set again,
for example when a new device is connected or the connection
is changed, you may need to restart the device.
Are many multi-media players connected? Up to 3 multi-media players that meet the HDMI CEC standards
can be connected at the same time.
The device name is not displayed under Device Connections
Check Remedy
Does the connected device meet the HDMI
CEC standards?
If the connected device does not meet the HDMI CEC standards,
it is not displayed. See the documentation and so on supplied
with the connected device for more information.
Network problems
Cannot access the network via wireless LAN
Check Remedy
Is Wireless LAN Power set to Off?Set Wireless LAN Power to On in the Configuration menu. If this
is already set to On, set Wireless LAN Power to Off, and then set
it to On again. s Network - Wireless LAN Power p.72
Is the passphrase correct? Note that the passphrase is case sensitive; upper case and lower
case letters are treated as different characters. If you have for-
gotten your passphrase, set a new one. s Network Settings -
Security - Passphrase p.72
Have you checked the Event ID? Check the Event ID number and perform the following steps.
s Info - Event ID p.76
s p.89
The image contains static during network projection
Check Remedy
Are there any obstacles between the access
point and the connected device?
Check for any obstacles between the access point, the mobile
device, the computer, and the projector, and change their posi-
tions to improve communication.
Is the distance between the access point and
the connected device too far?
Make sure that the access point, the mobile device, the comput-
er, and the projector are not too far apart. Move them closer to-
gether and try to connect again.
Are there any Bluetooth devices or micro-
wave oven in the vicinity?
If the wireless connection is slow or your projected image con-
tains noise, check for interference from other equipment, such
as a Bluetooth device or microwave. Move the interfering device
farther away or expand your wireless bandwidth.
Are too many devices connected? Reduce the number of connected devices if the connection
speed declines.
Troubleshooting
87
Cannot connect using Screen Mirroring
Check Remedy
Is Screen Mirroring set to Off?Set Screen Mirroring to On in the Configuration menu. If this is
already set to On, set Screen Mirroring to Off, and then set it to
On again. s Network - Screen Mirroring p.72
Is there a hyphen (-) in the display name? Change the Display Name so that it does not include "-" in the
projector's Screen Mirroring Settings menu. If the Display
Name includes "-", it may not be displayed correctly on your mo-
bile device. s Network - Screen Mirroring Settings p.72
Are other mobile devices already connected? Make sure no other mobile device is connected to the projector.
Are the settings correct for the mobile device? Make sure the settings on the mobile device are correct. If the
settings are correct, restart the mobile device.
Are you trying to reconnect immediately after
the Screen Mirroring connection has ended?
When connecting again immediately after disconnecting, it may
take some time until the connection is established. Reconnect
after waiting for a while.
Are you connecting from the connection his-
tory of the mobile device?
Once you have connected using Screen Mirroring, the projector
connection information may be recorded on the mobile device.
However, you may not be able to reconnect to the projector from
the recorded information. Select the projector from the list of
available devices.
The image contains static during Screen Mirroring connection
Check Remedy
Is the Wi-Fi antenna of the mobile device cov-
ered?
Try not to cover the Wi-Fi antenna of the mobile device.
Is the mobile device connected to the inter-
net?
If you use a Screen Mirroring connection and an internet con-
nection at the same time, the image may stop or contain noise.
Disconnect the internet connection to expand your wireless
bandwidth and improve the connection speed of the mobile
device.
Is there a problem in the projected content? Content that can be projected in Screen Mirroring is subject to
restrictions. Make sure the projected content meets the require-
ments. s p.59
Does the mobile device have a power saving
setting?
Depending on the settings of the mobile device, the connection
may be lost when the device enters the power saving mode.
Check the electrical power saving settings on the mobile device.
Is the mobile device using the latest version
of its wireless driver or firmware?
Update to the latest version of the wireless driver or firmware on
the mobile device.
Bluetooth device problems
Cannot Connect Bluetooth Device
Check Remedy
Was a device search performed? When connecting a Bluetooth device for the first time, or when
changing to another Bluetooth device, perform Search Blue-
tooth Device. s p.20
Troubleshooting
88
Check Remedy
Does the device support copyright protection
(SCMS-T)?
You cannot connect a Bluetooth device that does not support
copyright protection (SCMS-T).
Is the device based on A2DP? You cannot connect a Bluetooth device that does not support
A2DP.
The audio and connection for the Bluetooth device disconnects
Check Remedy
Are there any obstacles between the projec-
tor and the Bluetooth device?
Check for any obstacles between the projector and the Bluetooth
device, and change their positions to improve communication.
Is the device connected within the specified
communication distance?
If the distance between the projector and the Bluetooth device
exceed 10 m, the connection may be lost. Move the Bluetooth
device closer to the projector.
Are there any wireless equipment or micro-
wave ovens in the vicinity?
If the device is used at the same time as other wireless equipment
or microwave ovens, radio wave interference may occur, and the
image and audio may be interrupted. Avoid equipment that
could cause interference.
Other problems
No audio, or the audio is too low
Check Remedy
Is the volume too low? Adjust the volume so that you can hear the audio. s p.33
Is it connected with an HDMI cable? If no audio is output when connecting via an HDMI cable, set the
connected equipment to PCM output.
Are the Audio Out Device settings correct? Check that the Audio Out Device settings are correct on the
Configuration menu. s Settings - HDMI Link - Audio Out De-
vice p.68
Are the Bluetooth Audio settings correct? Make the following settings when connecting a Bluetooth audio
device.
•
To output audio from the projector's speaker or an AV system,
set Bluetooth Audio to Off.
•
To output audio from Bluetooth audio devices, set Bluetooth
Audio to On.
s Settings - Bluetooth - Bluetooth Audio p.68
Cannot make settings on the control panel
Check Remedy
Is Control Panel Lock set to Full Lock or Par-
tial Lock?
When Control Panel Lock is set to Full Lock in the Configura-
tion menu, all button operations on the control panel are disa-
bled; when Partial Lock is set, only the button on the control
panel is available. Perform operations from the remote control.
s Settings - Lock Setting - Control Panel Lock p.68
Troubleshooting
89
Slideshow does not start
Check Remedy
Is the USB storage device using a security
function?
You may not be able to use USB storage devices that incorporate
security functions.
About Event ID
Check the event ID and perform the remedy given below. If you cannot find the event ID in the table or resolve
the problem, contact your local dealer or the nearest Epson repair center.
s
Epson Projector Contact List
Event ID Cause Remedy
0020
0026
0032
0036
0037
A Screen Mirroring communication error oc-
curred.
Restart the projector and network software.
0021 Failed to startup Screen Mirroring. Restart the projector.
0022
0027
0028
0029
0030
0031
0035
Screen Mirroring communication is unstable. Check the network communication status, and
reconnect after waiting for a while.
0023
0024
0025
Failed to connect. If you see the PIN entry screen on your com-
puter, enter the PIN code displayed on the
Screen Mirroring standby screen or at the bot-
tom right of the projected image. If this does
not solve the problem, restart the projector and
the connected devices, and then check the
connection settings.
0038
0042
Wireless LAN system mismatch. Check the wireless LAN system for the mobile
device and the projector, and then reconnect.
0041 Failed to connect. Delete the connection information for the pro-
jector that is stored on the computer, and then
reconnect.
0043 The video format is not supported. Change the resolution of the mobile device,
and then reconnect. Or change the Adjust Im-
age Quality for the projector, and then recon-
nect.
0432
0435
Failed to start the network software. Restart the projector.
0433 An image that was transferred cannot be re-
produced.
Restart the network software.
0434
0481
0482
0485
Network communication is unstable. Check the network communication status, and
reconnect after waiting for a while.
Troubleshooting
90
Event ID Cause Remedy
0484 Communications was cut off from the comput-
er.
Restart the network software.
0483
04FE
The network software ended unexpectedly. Check the status of network communications.
Wait for a while and then try connecting again.
0479
04FF
A system error occurred in the projector. Restart the projector.
0891 The same SSID access point cannot be found. Set the computer, the access point, and the
projector to the same SSID.
0892 WPA and WPA2 authentication type mismatch. Check the setting of wireless LAN security to
see if it is correct.
0894 Communications was cut off because a con-
nection was made to the wrong access point.
Check with the network administrator and fol-
low their instructions.
0898 Failed to acquire the DHCP. Check the DHCP server to see if it is operating
correctly. Turn off DHCP if it is not being used.
s Network Settings - Wireless LAN - IP Set-
tings - DHCP p.72
0899 Other connection errors If restarting the projector or network software
does not solve the problem, contact your local
dealer or the nearest address provided in the
Epson Projector Contact List. s Epson Projector
Contact List
Maintenance
91
Maintenance
Cleaning the Parts
You should clean the projector if it becomes dirty or if the quality of projected images starts to deteriorate.
Warning
Before cleaning any part of the projector, turn it off and unplug the power cord. Never open any cover on
the projector, except as specifically explained in this manual. Dangerous electrical voltages in the projector
can injure you severely.
Cleaning the air filter
Clean the air filter if dust has accumulated on the air filter or when the following message is displayed.
"The projector is overheating. Make sure nothing is blocking the air vent, and clean or replace the air
filter."
c
Since the air filter is removable, you can clean both sides. Do not rinse the air filter in water. Do not
use detergents or solvents.
Attention
•If dust collects on the air filter, it can cause the internal temperature of the projector to rise, and this can lead
to problems with operation and shorten the optical engine's service life. Clean them frequently if you are
using the projector in a particularly dusty environment.
•Do not use an air duster. Combustible substances may remain, and dust may enter the precision components.
For ELPAF54
Remove any dust on the air filter by using a vacuum cleaner from the front side.
For ELPAF55
Maintenance
92
a
Open the air filter cover.
b
Remove the air filter.
Grip the air filter cover tab and pull it
straight up.
c
Hold the air filter with the surface
facing down and tap it 4 or 5 times to
remove the dust.
Tap the air filter on its side to remove the
dust.
Attention
If the air filter is hit too hard, it may
become unusable due to deformities
and cracks.
d
Remove any dust remaining on the air
filter by using a vacuum cleaner from
the front side.
e
Install the air filter.
Slide in the air filter until it clicks into place.
f
Close the air filter cover.
Cleaning the main unit
Clean the projector's surface by wiping it gently with a soft cloth.
If it is particularly dirty, moisten the cloth with water containing a small amount of neutral detergent, and
then firmly wring the cloth dry before using it to wipe the surface.
Attention
Do not use volatile substances such as wax, alcohol, or thinner to clean the projector's surface. The quality
of the case may change or the paint may peel off.
Maintenance
93
Cleaning the lens
Use a commercially available cloth for cleaning glasses to gently wipe off dirt from the lens.
Warning
Do not use a lens cleaner that contains flammable gas. The high heat generated by the projector lamp may
cause a fire.
Attention
Do not rub the lens with harsh materials or handle the lens too roughly as it can easily become damaged.
Cleaning the 3D Glasses
Use the cloth supplied to gently wipe off dirt from the lenses of
the 3D Glasses.
Attention
•
Do not rub the lenses of the glasses with harsh materials or
handle the lenses too roughly as they can easily become
damaged.
•
When maintenance is necessary, disconnect the USB Charg-
ing Adapter from the electrical outlet, and check that all ca-
bles have been disconnected.
c
The 3D Glasses contain rechargeable batteries. Observe local regulations when you dispose of them.
Replacement Periods for Consumables
Air filter replacement period
•If the message is displayed even though the air filter has been cleaned s p.91
Lamp replacement period
•The following message is displayed when projection starts:
It is time to replace your lamp.Please contact your Epson projector reseller or visit www.epson.com to purchase.
•The projected image gets darker or starts to deteriorate.
Maintenance
94
c
•The brightness of the projected image declines with the passage of projection time. The lamp
replacement message is displayed to help you maintain the brightness and image quality of the initial
image. The message display time differs depending on the menu settings, the environmental
conditions, and the usage conditions.
If you continue to use the lamp after the replacement period has passed, the possibility that the lamp
may explode increases. When the lamp replacement message appears, replace the lamp with a new
one as soon as possible, even if it is still working.
•Depending on the characteristics of the lamp and the way it has been used, the lamp may become
darker or stop working before the lamp warning message appears. You should always have a spare
lamp unit ready in case it is needed.
Replacing Consumables
Replacing the air filter
c
Dispose of used air filters properly in accordance with your local regulations.
Filter frame: ABS (ELPAF54)/Polypropylene (ELPAF55)
Filter: Polyurethane foam (ELPAF54)/Polypropylene (ELPAF55)
a
Press the button on the remote
control or the control panel to turn off
the power, and then disconnect the
power cord.
b
Open the air filter cover.
c
Remove the old air filter.
Grip the air filter cover tab and pull it
straight up.
d
Install the new air filter.
Slide in the air filter until it clicks into place.
e
Close the air filter cover.
Maintenance
95
Replacing the lamp
Warning
When replacing the lamp because it has stopped illuminating, there is a possibility that the lamp may be
broken. If replacing the lamp of a projector that has been suspended from the ceiling, you should always
assume that the lamp is cracked, and remove the lamp cover with care. When you open the lamp cover,
small shards of glass could fall out. If any shards of glass get into your eyes or mouth, contact a doctor
immediately.
Caution
•Do not touch the lamp cover immediately after turning off the projector as it is still hot. Wait until the lamp
has cooled down sufficiently before removing the lamp cover. Otherwise, you could get burnt.
•We recommend the use of genuine EPSON option lamps. The use of non-genuine lamps may affect projection
quality and safety.
Any damage or malfunction caused by the use of non-genuine lamps may not be covered by Epson's warranty.
a
Press the button on the remote
control or the control panel to turn off
the power, and then disconnect the
power cord.
b
Loosen the lamp cover fixing screw.
c
Remove the lamp cover.
Slide the lamp cover straight forward and
remove it.
d
Loosen the two lamp fixing screws.
e
Remove the old lamp.
Grip the projection and pull it straight out.
Maintenance
96
f
Install the new lamp.
Make sure the lamp is facing the correct
direction and press it in.
g
Tighten the two lamp fixing screws.
h
Replace the lamp cover.
Slide the cover back into place.
i
Tighten the lamp cover fixing screw.
Warning
Do not disassemble or remodel the lamp. If a modified or disassembled lamp is installed in the projector
and used, it could cause a fire, electric shock, or an accident.
Caution
•Make sure you install the lamp and lamp cover securely. If they are not installed correctly, the power does
not turn on.
•The lamp contains mercury (Hg). Dispose of used lamps in accordance with your local laws and regulations
on disposing of fluorescent tubing.
Resetting lamp hours
After replacing the lamp, make sure you reset the lamp hours.
The projector records how long the lamp is turned on and a message and indicator notify you when it is time
to replace the lamp.
a
Turn on the power.
b
Press the button.
The Configuration menu is displayed.
Maintenance
97
c
Select Reset - Reset Lamp Hours.
A reset confirmation message is displayed.
d
Use the buttons to select Yes,
and then press the button to
execute.
The lamp hours are reset.
Appendix
98
Optional Accessories and Consumables
The following optional accessories/consumables are available for purchase if required. This list of optional
accessories and consumables is current as of: May, 2017. Details of accessories are subject to change without
notice.
Varies depending on country of purchase.
Optional Items
Name Model No. Explanation
Ceiling mount (white)
*
ELPMB23 Use when installing the projector on a ceiling.
Ceiling pipe 450 (450 mm white)
*
ELPFP13 Use when installing the projector on a high ceil-
ing.
Ceiling pipe 700 (700 mm white)
*
ELPFP14
RF system 3D Glasses ELPGS03 Use when viewing 3D images.
USB Charging Adapter ELPAC01 Use when charging the 3D Glasses.
Computer cable (1.8 m) ELPKC02 Use when projecting a computer's screen.
Computer cable (3.0 m) ELPKC09
Computer cable (20.0 m) ELPKC10
*Special expertise is required to suspend the projector from a ceiling. Contact your local dealer.
Consumables
Name Model No. Explanation
Lamp unit ELPLP96 Use as a replacement for used lamps. (1 lamp)
Air filter ELPAF54 (for EH-
TW5600/EH-
TW5400) EL-
PAF55 (for EH-
TW5650)
Use as a replacement for used air filters. (Contains 2
air filters)
Appendix
99
Supported Resolutions
Computer Signals (Analog RGB)
Signal Refresh Rate (Hz) Resolution (dots)
VGA 60 640 x 480
SVGA 60 800 x 600
XGA 60 1024 x 768
SXGA 60 1280 x 960
60 1280 x 1024
WXGA 60 1280 x 768
60 1366 x 768
60 1280 x 800
WXGA++ 60 1600 x 900
HDMI1/HDMI2 Input Signal
Signal Refresh Rate (Hz) Resolution (dots)
SDTV (480i) 60 720 x 480
SDTV (576i) 50 720 x 576
SDTV (480p) 60 720 x 480
SDTV (576p) 50 720 x 576
HDTV (720p) 50/60 1280 x 720
HDTV (1080i) 50/60 1920 x 1080
HDTV (1080p) 24/30/50/60 1920 x 1080
MHL Input Signal
Signal Refresh Rate (Hz) Resolution (dots)
SDTV (480i) 60 720 x 480
SDTV (576i) 50 720 x 576
SDTV (480p) 60 720 x 480
SDTV (576p) 50 720 x 576
HDTV (720p) 50/60 1280 x 720
HDTV (1080i) 50/60 1920 x 1080
HDTV (1080p) 24/30 1920 x 1080
Appendix
100
3D Input Signal HDMI
Signal Refresh Rate
(Hz)
Resolution (dots) 3D Format
Frame Pack-
ing
Side by Side Top and Bot-
tom
HDTV (720p) 50/60 1280 x 720
HDTV (1080i) 50/60 1920 x 1080 - -
HDTV (1080p) 50/60 1920 x 1080 - -
HDTV (1080p) 24 1920 x 1080
3D Input Signal MHL
Signal Refresh Rate
(Hz)
Resolution (dots) 3D Format
Frame Pack-
ing
Side by Side Top and Bot-
tom
HDTV (720p) 50/60 1280 x 720 -
HDTV (1080i) 50/60 1920 x 1080 - -
HDTV (1080p) 50/60 1920 x 1080 - - -
HDTV (1080p) 24 1920 x 1080 -
Appendix
101
Specifications
Product name
EH-TW5650 EH-TW5600 EH-TW5400
Appearance
309 (W) x 107 (H) x 278 (D) mm (without projections)
Panel Size
0.61" wide
Display method
Polysilicon TFT active matrix
Resolution
1920 (W) x 1080 (H) x 3
Focus adjustment
Manual
Zoom adjustment
Manual (Approx. 1 to 1.6) Manual (Approx. 1 to
1.2)
Lamp (light source)
UHE lamp 200 W, Model No.: ELPLP96
Lamp replacement time
4,400 hours
Power supply
100 - 240 V AC ±10%, 50/60 Hz, 3.2 - 1.4 A
Power con-
sumption
100 to 120 V area
Operating: 312 W
Standby power consumption (Communication On): 2.0 W
Standby power consumption (Communication Off): 0.2 W
220 to 240 V area
Operating: 296 W
Standby power consumption (Communication On): 2.0 W
Standby power consumption (Communication Off): 0.2 W
Operating altitude
Altitude 0 to 3,000 m
Operating temperature
+5 to +35°C
*
(No condensation)
Storage temperature
-10 to +60°C (No condensation)
Mass
Approx. 3.5 kg Approx. 3.4 kg Approx. 3.2 kg
Connectors
PC port x 1, Mini D-Sub15-pin (female) blue
HDMI port x 2, HDMI
For HDCP, For CEC signals, For MHL signals (HDMI1 port only), For 3D
signals, Deep Color
USB 2.0 TypeA port x 1
Audio Out port x 1, Stereo mini jack
Speaker
Maximum input 10 W x 1
*The operating temperature is +5 to 30°C at an altitude of 2287 to 3000m.
This product is also designed for IT power distribution system with phase-to-phase voltage 230V.
Angle of tilt
If you use the projector tilted at an angle of more than 11°, it could be
damaged or cause an accident.
Appendix
102
DECLARATION of CONFORMITY
According to 47CFR, Part 2 and 15
Class B Personal Computers and Peripherals; and/or
CPU Boards and Power Supplies used with Class B Personal Computers
We: Epson America, Inc.
Located at: 3840 Kilroy Airport Way
MS: 3-13
Long Beach, CA 90806
Tel: 562-981-3840
Declare under sole responsibility that the product identified herein, complies with 47CFR Part 2 and 15 of the
FCC rules as a Class B digital device. Each product marketed, is identical to the representative unit tested and
found to be compliant with the standards. Records maintained continue to reflect the equipment being
produced can be expected to be within the variation accepted, due to quantity production and testing on a
statistical basis as required by 47CFR 2.909. Operation is subject to the following two conditions : (1) this
device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Trade Name: EPSON
Type of Product: LCD Projector
Model: H850C/H851C/H852C
FCC Compliance Statement
For United States Users
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures.
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
WARNING
The connection of a non-shielded equipment interface cable to this equipment will invalidate the FCC
Certification or Declaration of this device and may cause interference levels which exceed the limits
established by the FCC for this equipment. It is the responsibility of the user to obtain and use a shielded
equipment interface cable with this device. If this equipment has more than one interface connector, do not
leave cables connected to unused interfaces. Changes or modifications not expressly approved by the
manufacturer could void the user's authority to operate the equipment.
Appendix
103
Appearance
Units: mm
aCenter of lens
b Distance from center of lens to suspension bracket fixing point
Appendix
104
List of Safety Symbols
The following table lists the meaning of the safety symbols labeled on the equipment.
Symbol mark Approved stand-
ards
Meaning
IEC60417
No. 5007
"ON" (power)
To indicate connection to the mains.
IEC60417
No. 5008
"OFF" (power)
To indicate disconnection from the mains.
IEC60417
No. 5009
Stand-by
To identify the switch or switch position by means of which part
of the equipment is switched on in order to bring it into the stand-
by condition.
ISO7000
No. 0434B
IEC3864-B3.1
Caution
To identify general caution when using the product.
IEC60417
No. 5041
Caution, hot surface
To indicate that the marked item can be hot and should not be
touched without taking care.
IEC60417
No. 6042
ISO3864-B3.6
Caution, risk of electric shock
To identify equipment that has risk of electric shock.
IEC60417
No. 5957
For indoor use only
To identify electrical equipment designed primarily for indoor
use.
IEC60417
No. 5926
Polarity of d.c. power connector
To identify the positive and negative connections (the polarity)
on a piece of equipment to which a d.c. power supply may be
connected.
---
IEC60417
No. 5001B
Battery, general
On battery powered equipment. To identify a device for instance
a cover for the battery compartment, or the connector terminals.
IEC60417
No. 5002
Positioning of cell
To identify the battery holder itself and to identify the positioning
of the cell(s) inside the battery holder.
---
IEC60417
No. 5019
Protective earth
To identify any terminal which is intended for connection to an
external conductor for protection against electric shock in case
of a fault, or the terminal of a protective earth electrode.
IEC60417
No. 5017
Earth
To identify an earth (ground) terminal in cases where neither the
symbol is explicitly required.
Appendix
105
Symbol mark Approved stand-
ards
Meaning
IEC60417
No. 5032
Alternating current
To indicate on the rating plate that the equipment is suitable for
alternating current only; to identify relevant terminals.
IEC60417
No. 5031
Direct current
To indicate on the rating plate that the equipment is suitable for
direct current only; to identify relevant terminals.
IEC60417
No. 5172
Class II equipment
To identify equipment meeting the safety requirements specified
for Class II equipment according to IEC 61140.
ISO 3864 General prohibition
To identify actions or operations that are prohibited.
ISO 3864 Contact prohibition
To indicate injury that could occur due to touching a specific part
of the equipment.
--- Never look into the projection lens while the projector is on.
--- To indicate that the marked item don't place anything on pro-
jector.
ISO3864
IEC60825-1
Caution, laser radiation
To indicate the equipment has a laser radiation part.
ISO 3864 Disassembly prohibition
To indicate a risk of injury, such as electric shock, if the equipment
is disassembled.
Appendix
106
Glossary
This section briefly explains the difficult terms that are not explained in context in the text of this guide. For
details, refer to other commercially available publications.
Aspect Ratio
The ratio between an image's length and its height. Screens with a horizontal:vertical ratio
of 16:9, such as HDTV screens, are known as wide screens.
SDTV and general computer displays have an aspect ratio of 4:3.
HDCP
HDCP is an abbreviation for High-bandwidth Digital Content Protection. It is used to pre-
vent illegal copying and protect copyrights by encrypting digital signals sent over DVI and
HDMI ports. Because the HDMI port on this projector supports HDCP, it can project digital
images protected by HDCP technology. However, the projector may not be able to project
images protected with updated or revised versions of HDCP encryption.
HDMI
™
An abbreviation for High Definition Multimedia Interface. This is the standard by which
HD images and multichannel audio signals are digitally transmitted.
HDMI
™
is a standard aimed at digital consumer electronics and computers. By not com-
pressing the digital signal, the image can be transferred at the highest quality possible. It
also provides an encryption function for the digital signal.
HDTV
An abbreviation for High-Definition Television. This refers to high-definition systems
which satisfy the following conditions.
•
Vertical resolution of 720p or 1080i or greater (p = Progressive, i = Interlace)
•
Screen aspect of 16:9 Dolby Digital audio reception and playback (or output)
MHL
An abbreviation for Mobile High-definition Link, which is a standard high-definition in-
terface that enables high-speed transfer of video signals on mobile devices.
It is a standard targeting smartphones and tablets that transfers uncompressed digital
signals without loss of quality and also enables simultaneous charging of such devices.
Pairing
Register devices in advance when connecting with Bluetooth devices to ensure mutual
communication.
SDTV
An abbreviation for Standard Definition Television. This refers to standard television sys-
tems which do not satisfy the conditions for HDTV High-Definition Television.
SVGA
A screen size standard with a resolution of 800 (horizontal) x 600 (vertical) dots.
SXGA
A screen size standard with a resolution of 1,280 (horizontal) x 1,024 (vertical) dots.
VGA
A screen size standard with a resolution of 640 (horizontal) x 480 (vertical) dots.
XGA
A screen size standard with a resolution of 1,024 (horizontal) x 768 (vertical) dots.
YCbCr
In component image signals for SDTV, Y is the brightness, while Cb and Cr indicate the
color difference.
YPbPr
In component image signals for HDTV, Y is the brightness, while Pb and Pr indicate the
color difference.
Appendix
107
General Notes
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted
in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior
written permission of Seiko Epson Corporation. No patent liability is assumed with respect to the use of the
information contained herein. Neither is any liability assumed for damages resulting from the use of the infor-
mation contained herein.
Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties
for damages, losses, costs, or expenses incurred by the purchaser or third parties as a result of: accident, misuse,
or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the
U.S.) failure to strictly comply with Seiko Epson Corporation's operating and maintenance instructions.
Seiko Epson Corporation shall not be liable against any damages or problems arising from the use of any options
or any consumable products other than those designated as Original Epson Products or Epson Approved Prod-
ucts by Seiko Epson Corporation.
The contents of this guide may be changed or updated without further notice.
Illustrations in this guide and the actual projector may differ.
Restriction of Use
When this product is used for applications requiring high reliability/safety such as transportation devices related
to aviation, rail, marine, automotive etc.; disaster prevention devices; various safety devices etc; or functional/
precision devices etc, you should use this product only after giving consideration to including fail-safes and
redundancies into your design to maintain safety and total system reliability. Because this product was not
intended for use in applications requiring extremely high reliability/safety such as aerospace equipment, main
communication equipment, nuclear power control equipment, or medical equipment related to direct medical
care etc, please make your own judgment on this product’s suitability after a full evaluation.
Appendix
108
General Notice
EPSON is the registered trademark of Seiko Epson Corporation. EXCEED YOUR VISION and ELPLP are the trade-
marks or registered trademarks of Seiko Epson Corporation.
HDMI and High-Definition Multimedia Interface are the trademarks or registered trademarks of HDMI Licensing
LLC.
Windows is the trademark or registered trademark of Microsoft Corporation in the United States and/or other
countries.
Mac, Mac OS, OS X, and macOS are trademarks of Apple Inc.
The Bluetooth
®
word mark and logo are registered trademarks of Bluetooth SIG, Inc., and the Seiko Epson Cor-
poration uses these marks under license. Other trademarks or trade names are the property of their respective
owners.
Bluetopia
®
is provided for your use by Stonestreet One, LLC
®
under a software license agreement. Stonestreet
One, LLC
®
is and shall remain the sole owner of all right, title and interest whatsoever in and to Bluetopia
®
and
your use is subject to such ownership and to the license agreement. Stonestreet One, LLC
®
reserves all rights
related to Bluetopia
®
not expressly granted under the license agreement and no other rights or licenses are
granted either directly or by implication, estoppel or otherwise, or under any patents, copyrights, mask works,
trade secrets or other intellectual property rights of Stonestreet One, LLC
®
.
© 2000-2012 Stonestreet One, LLC
®
All Rights Reserved.
MHL, the MHL logo, and Mobile High-Definition Link are trademarks, registered trademarks, or service marks of
MHL and LLC in the United States and/or other countries.
Wi-Fi
®
, Miracast
®
, WPA
™
, and WPA2
™
are registered trademarks of the Wi-Fi Alliance.
App Store is a service mark of Apple Inc.
Google Play is a trademark of Google Inc.
"QR Code" is a registered trademark of DENSO WAVE INCORPORATED.
Qualcomm aptX is a product of Qualcomm Technologies International, Ltd. Qualcomm is a trademark of Qual-
comm Incorporated, registered in the United States and other countries, used with permission. aptX is a trade-
mark of Qualcomm Technologies International, Ltd., registered in the United States and other countries, used
with permission.
Other product names used herein are also for identification purposes only and may be trademarks of their
respective owners. Epson disclaims any and all rights in those marks.
©SEIKO EPSON CORPORATION 2017. All rights reserved.
Indication of the manufacturer and the importer in accordance with requirements of EU directive
Manufacturer: SEIKO EPSON CORPORATION
Address: 3-5, Owa 3-chome, Suwa-shi, Nagano-ken 392-8502 Japan
Telephone: 81-266-52-3131
http://www.epson.com/
Importer: SEIKO EUROPE B.V.
Address: Azië building, Atlas ArenA, Hoogoorddreef 5, 1101 BA Amster-
dam Zuidoost The Netherlands
Telephone: 31-20-314-5000
http://www.epson.eu/
Index
109
3
3D brightness ................................................. 67
3D conversion ................................................. 46
3D display ......................................................... 67
3D format ......................................................... 67
3D Glasses ........................................................ 44
3D images ........................................................ 43
3D settings ....................................................... 67
3D viewing notice ......................................... 67
A
A/V Mute ........................................................... 33
Adjusting focus .............................................. 28
Adjusting RGB ................................................. 38
Adjusting the position of the image ...... 29
Adjusting the tilt ............................................ 29
Advanced .................................................. 66, 68
Air filter .............................................................. 91
Air filter cover .......................................... 92, 94
Air filter replacement period ..................... 93
Appearance ................................................... 103
Aspect ......................................................... 35, 67
Auto iris ...................................................... 36, 66
Auto setup ....................................................... 67
Auto V-Keystone ..................................... 30, 68
B
Basic menu ....................................................... 74
Bluetooth ......................................................... 69
Brightness .......................................... 38, 65, 66
C
CEC standards ................................................. 49
Channel ............................................................. 74
Child lock .......................................................... 70
Cleaning the 3D Glasses ............................. 93
Cleaning the air filter .................................... 91
Cleaning the lens ........................................... 93
Cleaning the main unit ................................ 92
Color mode ............................................... 34, 65
Color saturation ............................................. 65
Color Temp. ..................................................... 65
Configuration menu ..................................... 64
Connecting ...................................................... 18
Connecting a computer .............................. 18
Connecting Bluetooth devices ................. 20
Connecting external speakers .................. 19
Connecting smartphones or tablets ...... 18
Connecting USB devices ............................. 19
Connecting video equipment .................. 18
Connection Mode ......................................... 74
Contrast ............................................................ 65
Control Panel ..................................................... 7
Control panel ..................................................... 6
Control panel lock ......................................... 70
Cool-down ....................................................... 27
D
Detail Enhancement .............................. 36, 65
DHCP .................................................................. 75
Direct power on ............................................. 72
Display ............................................................... 71
Display Background ..................................... 71
Display LAN Info. ........................................... 74
Display the QR Code .................................... 73
Displaying the test pattern ........................ 28
E
Error/Warning indicators ............................ 77
Event ID ............................................................. 89
Extended menu .............................................. 71
F
Focus .................................................................. 82
Focus adjustment .......................................... 28
Focus ring .................................................... 6, 28
Frame Interpolation ..................................... 65
Full ...................................................................... 35
G
Gain ............................................................. 38, 66
Gamma .............................................................. 39
Gateway Address ........................................... 75
H
H/V-Keystone ........................................... 31, 68
HDMI link .......................................................... 49
HDMI port ......................................................... 49
Height adjustment ........................................ 29
High altitude mode ...................................... 72
H-Keystone ...................................................... 68
H-Keystone adjuster .............................. 31, 68
Home screen ................................................... 26
Horizontal keystone adjuster ...................... 7
Hue .............................................................. 38, 66
I
Illumination ..................................................... 72
Image ................................................................. 34
Image Enhancement .................................... 65
Image enhancement .................................... 35
Image menu .................................................... 65
Index
110
Images ............................................................... 51
Indicators .......................................................... 77
Info menu ......................................................... 76
Inverse 3D Glasses ......................................... 67
IP Address ......................................................... 75
IP Address Display ......................................... 75
IP Settings ........................................................ 75
K
Keystone ........................................................... 68
L
Lamp cover ................................................. 6, 95
Lamp cover fixing screw ............................. 95
Lamp replacement period ......................... 93
Language ......................................................... 72
Lens shift dial .................................................. 29
Load memory .................................................. 41
Lock setting ..................................................... 70
M
Memory ............................................................. 70
Memory function ........................................... 41
Menu .................................................................. 64
Messages .......................................................... 71
MPEG Noise Reduction ......................... 35, 65
N
Network menu ............................................... 72
Noise .................................................................. 82
Noise Reduction ...................................... 35, 65
O
Offset .......................................................... 38, 66
Operating range ............................................ 24
Operating time ............................................... 96
Operation ......................................................... 72
Overscan ........................................................... 67
P
Pairing ............................................................... 45
Passphrase ....................................................... 75
Position ............................................................. 67
Power ................................................................. 27
Power consumption ..................................... 66
Power supply .................................................. 25
Projection ......................................................... 71
Projection size ................................................ 28
Projector Info .................................................. 76
Projector name ............................................... 74
Q
Quick Corner ............................................ 32, 68
R
Remote Control ................................................ 9
Remote control .............................................. 23
Remote Password .......................................... 74
Replacement periods for consumables
................................................................................ 93
Replacement time ......................................... 93
Replacing consumables .............................. 94
Replacing the air filter .................................. 94
Replacing the lamp ....................................... 95
Reset .............................................. 66, 68, 71, 72
Reset all ............................................................. 76
Reset lamp hours .................................... 76, 96
Reset memory ................................................. 76
Reset menu ............................................... 75, 76
RGB ..................................................................... 66
RGBCMY ..................................................... 38, 66
S
Saturation .................................................. 38, 66
Save memory .................................................. 41
Search Access Point ...................................... 75
Security ............................................................. 75
Security menu ................................................ 75
Settings menu ................................................ 68
Sharpness .................................................. 35, 65
Signal menu .................................................... 66
Sleep mode ...................................................... 72
Slideshow ......................................................... 51
Soft Keyboard ................................................. 74
Source ................................................................ 26
Specifications ............................................... 101
Split Screen ...................................................... 53
Split screen ...................................................... 68
SSID .................................................................... 75
SSID Display ..................................................... 75
Standby Mode ................................................ 72
Startup Screen ................................................ 71
Sub menu ......................................................... 64
Subnet Mask .................................................... 75
Supported resolutions ................................. 99
Sync. ................................................................... 67
T
Tint ...................................................................... 65
Top menu ......................................................... 64
Tracking ............................................................ 67
Index
111
U
USB ..................................................................... 51
User button ...................................................... 70
V
Version .............................................................. 76
V-Keystone ....................................................... 68
Volume ....................................................... 33, 68
W
Wireless LAN menu ....................................... 74
Wireless LAN Power ...................................... 73
Z
Zoom .................................................................. 35
Zoom adjustment ......................................... 28
Zoom ring ........................................................... 6