Table of Contents
- Contents
- Guide to This Manual
- Important Instructions
- Part Names and Functions
- Guide to the Control Panel
- Loading Paper
- Placing Originals
- Printing
- Copying
- Scanning
- Faxing
- Maintaining the Printer
- Checking the Status of Consumable
- Cleaning the Paper Path for Paper Feeding Problems
- Improving Print, Copy, Scan, and Fax Quality
- Cleaning the Printer
- Cleaning Spilled ink
- Checking the Total Number of Pages Fed Through the Printer
- Saving Power
- Installing or Uninstalling Applications Separately
- Transporting and Storing the Printer
- Solving Problems
- Adding or Replacing the Computer or Devices
- Product Information
- Administrator Information
- Where to Get Help
- Technical Support Web Site
- Contacting Epson Support
- Before Contacting Epson
- Help for Users in Europe
- Help for Users in Taiwan
- Help for Users in Australia
- Help for Users in New Zealand
- Help for Users in Singapore
- Help for Users in Thailand
- Help for Users in Vietnam
- Help for Users in Indonesia
- Help for Users in Hong Kong
- Help for Users in Malaysia
- Help for Users in India
- Help for Users in the Philippines
Epson ET-5150 User Manual
Displayed below is the user manual for ET-5150 by Epson which is a product in the Multifunctionals category. This manual has pages.
Related Manuals
Contents
Guide to This Manual
Introduction to the Manuals...................7
Searching for Information....................7
Printing Only the Pages You Need.............. 8
About is Manual......................... 8
Marks and Symbols.......................8
Notes on Screenshots and Illustrations.........9
Operating System References................9
Trademarks..............................10
Copyright...............................11
Important Instructions
Safety Instructions.........................13
Safety Instructions for Ink................. 13
Printer Advisories and Warnings.............. 14
Advisories and Warnings for Setting Up the
Printer................................14
Advisories and Warnings for Using the Printer. . 14
Advisories and Warnings for Using the
Touchscreen........................... 15
Advisories and Warnings for Using the
Printer with a Wireless Connection...........15
Advisories and Warnings for Transporting or
Storing the Printer.......................16
Protecting Your Personal Information...........16
Part Names and Functions
Front...................................18
Inside..................................19
Rear................................... 20
Guide to the Control Panel
Control Panel............................ 22
Touch Screen Operations....................22
Home Screen Conguration..................23
Guide to the Network Icon.................24
Menu Screen Conguration..................25
Entering Characters........................26
Viewing Animations....................... 26
Loading Paper
Paper Handling Precautions..................29
Paper Size and Type Settings..................29
List of Paper Type....................... 30
Loading Paper............................31
Precautions when Loading Letterhead Paper. . . . 31
Loading Various Paper......................32
Loading Envelopes.......................32
Loading Pre-punched Paper................33
Outputting Paper..........................33
Placing Originals
Placing Originals..........................35
Originals that are not Supported by the ADF. . . . . . 36
Printing
Printing Documents........................38
Printing from a Computer - Windows.........38
Printing from a Computer - Mac OS..........55
Printing Documents from Smart Devices (iOS). . 61
Printing Documents from Smart Devices
(Android).............................62
Printing on Envelopes...................... 63
Printing on Envelopes from a Computer
(Windows)............................ 63
Printing on Envelopes from a Computer
(Mac OS)..............................64
Printing Web Pages........................ 64
Printing Web Pages from a Computer.........64
Printing Web Pages from Smart Devices.......64
Printing Using a Cloud Service................65
Registering to Epson Connect Service from
the Control Panel........................66
Copying
Available Copying Methods..................68
Copying Originals.......................68
Copying on 2-Sides...................... 69
Copying by Enlarging or Reducing...........69
Copying Multiple Originals onto One Sheet. . . . .70
Copying Originals Using Good Quality. . . . . . . . 71
Copying ID card........................ 71
Copying in Page Order....................72
Basic Menu Options for Copying.............. 72
B&W:................................72
2
Color:................................72
(2-Sided):............................. 72
(Density):............................. 72
Advanced Menu Options for Copying...........73
Paper Setting:.......................... 73
Reduce/Enlarge:.........................73
Original Size:...........................73
Multi-Page:............................73
Quality:...............................74
Finishing:............................. 74
Original Orientation:.....................74
Remove Shadow:........................74
Remove Punch Holes:.................... 74
ID Card Copy:..........................74
Clear All Settings:....................... 74
Scanning
Basic Information on Scanning................76
What is a "Scan"?........................76
Scanning Uses..........................76
Available Scanning Methods................76
Recommended File Formats to Suit Your
Purpose...............................78
Recommended Resolutions to Suit Your
Purpose...............................78
Scanning Originals to a Computer............. 79
Scanning from the Control Panel............ 79
Scanning from a Computer.................80
Scanning Originals to the Cloud...............80
Basic Menu Options for Scanning to the Cloud. . 81
Advanced Menu Options for Scanning to the
Cloud................................81
Scanning Using WSD.......................82
Setting Up a WSD Port....................82
Scanning Originals to a Smart Device...........84
Faxing
Before Using Fax Features....................86
Overview of this Printer's Fax Features..........86
Feature: Sending Faxes...................86
Feature: Receiving Faxes...................87
Feature: PC-FAX Send/Receive
(Windows/Mac OS)......................87
Features: Various Fax Reports...............88
Feature: Security when Sending and
Receiving Faxes.........................88
Features: Other Useful Features............ 88
Sending Faxes Using the Printer...............89
Selecting Recipients......................89
Various Ways of Sending Faxes..............90
Receiving Faxes on the Printer................92
Receiving Incoming Faxes................. 93
Receiving Faxes by Making a Phone Call.......94
Viewing Received Faxes Saved in the Printer
on the LCD Screen.......................95
Menu Options for Faxing....................96
Recipient..............................96
Fax Settings............................96
More.................................98
Menu Options for Inbox.....................99
Open Inbox (XX Unread)..................99
Using Other Faxing Features.................100
Printing Fax Report Manually..............100
Sending a Fax from a Computer..............100
Sending Documents Created Using an
Application (Windows).................. 100
Sending Documents Created Using an
Application (Mac OS)....................102
Receiving Faxes on a Computer...............104
Checking for New Faxes (Windows).........104
Checking for New Faxes (Mac OS).......... 106
Canceling the Feature that Saves Incoming
Faxes to the Computer...................106
Maintaining the Printer
Checking the Status of Consumable............109
Cleaning the Paper Path for Paper Feeding
Problems...............................109
Improving Print, Copy, Scan, and Fax Quality. . . . 111
Checking and Cleaning the Print Head.......111
Running Power Cleaning.................112
Preventing nozzle clogging................114
Aligning the Print Head..................114
Cleaning the Paper Path for Ink Smears.......114
Cleaning the Scanner Glass................114
Cleaning the ADF...................... 115
Cleaning the Translucent Film............. 118
Cleaning the Printer.......................121
Cleaning Spilled ink.......................121
3
Checking the Total Number of Pages Fed
rough the Printer.......................122
Saving Power............................122
Saving Power (Control Panel)..............122
Installing or Uninstalling Applications Separately. 123
Installing the Applications Separately........ 123
Adding the Printer (for Mac OS Only)........125
Uninstalling Applications.................125
Updating Applications and Firmware. . . . . . . . 127
Transporting and Storing the Printer...........128
Solving Problems
e Printer Does Not Work as Expected........134
e Printer Does Not Turn On or O........134
Power Turns O Automatically.............134
Paper Does Not Feed Properly. . . . . . . . . . . . . 134
Cannot Print..........................139
Cannot Start Scanning...................156
Cannot Send or Receive Faxes..............167
Cannot Operate the Printer as Expected. . . . . . 180
A Message is Displayed on the LCD Screen. . . . . . 183
Paper Gets Jammed.......................184
Removing Jammed Paper.................185
Removing Jammed Paper from the ADF......189
Preventing Paper Jams...................191
It is Time to Rell the Ink...................192
Ink Bottle Handling Precautions............192
Relling the Ink Tank....................193
It is Time to Replace the Maintenance Box. . . . . . .196
Maintenance Box Handling Precautions. . . . . . 196
Replacing a Maintenance Box..............197
Printing, Copying, Scanning, and Faxing
Quality is Poor...........................198
Print Quality is Poor.....................198
Copy Quality is Poor.................... 204
Scanned Image Problems.................210
e Quality of the Sent Fax is Poor..........213
Received Fax Quality is Poor...............215
Cannot Solve Problem.....................215
Cannot Solve Printing or Copying Problems. . . 215
Adding or Replacing the Computer or
Devices
Connecting to a Printer that has been
Connected to the Network..................218
Using a Network Printer from a Second
Computer............................218
Using a Network Printer from a Smart Device. . 219
Re-setting the Network Connection........... 219
When Replacing the Wireless Router.........219
When Changing the Computer.............220
Changing the Connection Method to the
Computer............................220
Making Wi-Fi Settings from the Control Panel. .221
Connecting a Smart Device and Printer Directly
(Wi-Fi Direct)...........................225
About Wi-Fi Direct..................... 225
Connecting to Devices using Wi-Fi Direct. . . . .226
Disconnecting Wi-Fi Direct (Simple AP)
Connection...........................228
Changing the Wi-Fi Direct (Simple AP)
Settings Such as the SSID.................228
Checking the Network Connection Status.......229
Checking the Network Connection Status
from the Control Panel...................229
Printing a Network Connection Report. . . . . . . 230
Printing a Network Status Sheet............ 236
Checking the Network of the Computer
(Windows only)........................236
Product Information
Paper Information........................239
Available Paper and Capacities.............239
Unavailable Paper Types..................241
Consumable Products Information............242
Ink Bottle Codes....................... 242
Maintenance Box Code...................243
Soware Information......................243
Soware for Printing.................... 243
Soware for Scanning....................247
Soware for Faxing..................... 247
Soware for Package Creation..............248
Soware for Making Settings.............. 249
Soware for Updating................... 251
Settings Menu List........................251
General Settings........................251
Maintenance..........................262
Print Status Sheet.......................263
Print Counter..........................263
User Settings..........................264
Restore Default Settings..................264
Firmware Update.......................264
Product Specications..................... 265
Printer Specications....................265
Scanner Specications................... 265
ADF Specications......................266
4
Fax Specications.......................266
Using Port for the Printer.................267
Interface Specications...................268
Network Specications...................268
Supported ird Party Services.............270
Dimensions...........................270
Electrical Specications.................. 270
Environmental Specications..............271
System Requirements....................272
Regulatory Information....................272
Standards and Approvals................. 272
Restrictions on Copying..................274
Administrator Information
Connecting the Printer to the Network.........276
Before Making Network Connection.........276
Connecting to the Network from the Control
Panel................................278
Settings to Use the Printer...................280
Making Contacts Available................280
Making Fax Features Available.............282
Problems when Making Settings............291
Where to Get Help
Technical Support Web Site..................295
Contacting Epson Support..................295
Before Contacting Epson................. 295
Help for Users in Europe..................295
Help for Users in Taiwan..................295
Help for Users in Australia................296
Help for Users in New Zealand.............296
Help for Users in Singapore............... 297
Help for Users in ailand................297
Help for Users in Vietnam................ 298
Help for Users in Indonesia................298
Help for Users in Hong Kong..............301
Help for Users in Malaysia................ 302
Help for Users in India...................302
Help for Users in the Philippines............303
5
Guide to This Manual
Introduction to the Manuals...........................................7
Searching for Information.............................................7
Printing Only the Pages You Need.......................................8
About is Manual..................................................8
Trademarks...................................................... 10
Copyright........................................................11
Introduction to the Manuals
e following manuals are supplied with your Epson printer. As well as the manuals, check the various types of
help information available from the printer itself or from the Epson soware applications.
❏Important Safety Instructions (paper manual)
Provides you with instructions to ensure the safe use of this printer.
❏Start Here (paper manual)
Provides you with information on setting up the printer and installing the soware.
❏User's Guide (digital manual)
is manual. is manual is available as PDF and Web manuals. Provides overall information and instructions
on using the printer, on network settings when using the printer on a network, and on solving problems.
is manual is used for the ET-5170 Series/L6490 Series and ET-5150 Series/L6460 Series. However, the Faxing
feature is only available for theET-5170 Series/L6490 Series.
❏Faxing
You can obtain the latest versions of the above manuals with the following methods.
❏Paper manual
Visit the Epson Europe support website at http://www.epson.eu/support, or the Epson worldwide support
website at http://support.epson.net/.
❏Digital manual
To view the Web manual, visit the following website, enter the product name, and then go to Support.
http://epson.sn
Related Information
&“Application for Updating Soware and Firmware (EPSON Soware Updater)” on page 251
Searching for Information
e PDF manual allows you to search for information you are looking for by keyword, or jump directly to specic
sections using the bookmarks. is section explains how to use a PDF manual that has been opened in Adobe
Acrobat Reader DC on your computer.
Searching by keyword
Click Edit > Advanced Search. Enter the keyword (text) for information you want to nd in the search window,
and then click Search. Hits are displayed as a list. Click one of the displayed hits to jump to that page.
Guide to This Manual
>
Searching for Information
7
Jumping directly from bookmarks
Click a title to jump to that page. Click + or > to view the lower level titles in that section. To return to the previous
page, perform the following operation on your keyboard.
❏Windows: Hold down Alt. and then press ←.
❏Mac OS: Hold down the command key, and then press ←.
Printing Only the Pages You Need
You can extract and print only the pages you need. Click Print in the File menu, and then specify the pages you
want to print in Pages in Pages to Print.
❏To specify a series of pages, enter a hyphen between the start page and the end page.
Example: 20-25
❏To specify pages that are not in series, divide the pages with commas.
Example: 5, 10, 15
About This Manual
is section explains the meaning of marks and symbols, notes on descriptions, and operating system reference
information used in this manual.
Marks and Symbols
!
Caution:
Instructions that must be followed carefully to avoid bodily injury.
Guide to This Manual
>
About This Manual
>
Marks and Symbols
8
c
Important:
Instructions that must be observed to avoid damage to your equipment.
Note:
Provides complementary and reference information.
Related Information
&Links to related sections.
Notes on Screenshots and Illustrations
❏Screenshots of the printer driver are from Windows 10 or macOS High Sierra. e content displayed on the
screens varies depending on the model and situation.
❏Illustrations used in this manual are examples only. Although there may be slight dierences depending on the
model, the method of operation is the same.
❏Some of the menu items on the LCD screen vary depending on the model and settings.
❏You can read the QR code using dedicated app.
Operating System References
Windows
In this manual, terms such as "Windows 10", "Windows 8.1", "Windows 8", "Windows 7", "Windows Vista",
"Windows XP", "Windows Server 2019", "Windows Server 2016", "Windows Server 2012 R2", "Windows Server
2012", "Windows Server 2008 R2", "Windows Server 2008", "Windows Server 2003 R2", and "Windows Server
2003" refer to the following operating systems. Additionally, "Windows" is used to refer to all versions.
❏Microso
®
Windows
®
10 operating system
❏Microso
®
Windows
®
8.1 operating system
❏Microso
®
Windows
®
8 operating system
❏Microso
®
Windows
®
7 operating system
❏Microso
®
Windows Vista
®
operating system
❏Microso
®
Windows
®
XP operating system
❏Microso
®
Windows
®
XP Professional x64 Edition operating system
❏Microso
®
Windows Server
®
2019 operating system
❏Microso
®
Windows Server
®
2016 operating system
❏Microso
®
Windows Server
®
2012 R2 operating system
❏Microso
®
Windows Server
®
2012 operating system
❏Microso
®
Windows Server
®
2008 R2 operating system
❏Microso
®
Windows Server
®
2008 operating system
❏Microso
®
Windows Server
®
2003 R2 operating system
❏Microso
®
Windows Server
®
2003 operating system
Guide to This Manual
>
About This Manual
>
Operating System References
9
Mac OS
In this manual, "Mac OS" is used to refer to Mac OS X v10.6.8 or later.
Trademarks
❏EPSON
®
is a registered trademark, and EPSON EXCEED YOUR VISION or EXCEED YOUR VISION is a
trademark of Seiko Epson Corporation.
❏Epson Scan 2 soware is based in part on the work of the Independent JPEG Group.
❏libti
Copyright © 1988-1997 Sam Leer
Copyright © 1991-1997 Silicon Graphics, Inc.
Permission to use, copy, modify, distribute, and sell this soware and its documentation for any purpose is
hereby granted without fee, provided that (i) the above copyright notices and this permission notice appear in
all copies of the soware and related documentation, and (ii) the names of Sam Leer and Silicon Graphics
may not be used in any advertising or publicity relating to the soware without the specic, prior written
permission of Sam Leer and Silicon Graphics.
THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND, EXPRESS,
IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR ANY SPECIAL,
INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND, OR ANY DAMAGES
WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER OR NOT ADVISED
OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF LIABILITY, ARISING OUT OF OR IN
CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
❏QR Code is a registered trademark of DENSO WAVE INCORPORATED in Japan and other countries.
❏Microso
®
, Windows
®
, Windows Server
®
, and Windows Vista
®
are registered trademarks of Microso
Corporation.
❏Apple, Mac, macOS, OS X, Bonjour, Safari, AirPrint, iPad, iPhone, iPod touch, and iTunes are trademarks of
Apple Inc., registered in the U.S. and other countries.
❏Use of the Works with Apple badge means that an accessory has been designed to work specically with the
technology identied in the badge and has been certied by the developer to meet Apple performance
standards.
❏Chrome, Google Play, and Android are trademarks of Google LLC.
❏Adobe and Adobe Reader are either registered trademarks or trademarks of Adobe Systems Incorporated in the
United States and/or other countries.
❏Firefox is a trademark of the Mozilla Foundation in the U.S. and other countries.
❏Mopria® and the Mopria® Logo are registered and/or unregistered trademarks and service marks of Mopria
Alliance, Inc. in the United States and other countries. Unauthorized use is strictly prohibited.
❏General Notice: Other product names used herein are for identication purposes only and may be trademarks
of their respective owners. Epson disclaims any and all rights in those marks.
Guide to This Manual
>
Trademarks
10
Copyright
No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any
means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of
Seiko Epson Corporation. No patent liability is assumed with respect to the use of the information contained
herein. Neither is any liability assumed for damages resulting from the use of the information herein. e
information contained herein is designed only for use with this Epson product. Epson is not responsible for any
use of this information as applied to other products.
Neither Seiko Epson Corporation nor its aliates shall be liable to the purchaser of this product or third parties for
damages, losses, costs, or expenses incurred by the purchaser or third parties as a result of accident, misuse, or
abuse of this product or unauthorized modications, repairs, or alterations to this product, or (excluding the U.S.)
failure to strictly comply with Seiko Epson Corporation's operating and maintenance instructions.
Seiko Epson Corporation and its aliates shall not be liable for any damages or problems arising from the use of
any options or any consumable products other than those designated as Original Epson Products or Epson
Approved Products by Seiko Epson Corporation.
Seiko Epson Corporation shall not be held liable for any damage resulting from electromagnetic interference that
occurs from the use of any interface cables other than those designated as Epson Approved Products by Seiko
Epson Corporation.
© 2020 Seiko Epson Corporation
e contents of this manual and the specications of this product are subject to change without notice.
Guide to This Manual
>
Copyright
11
Safety Instructions
Read and follow these instructions to ensure safe use of this printer. Make sure you keep this manual for future
reference. Also, be sure to follow all warnings and instructions marked on the printer.
❏Some of the symbols used on your printer are to ensure safety and proper use of the printer. Visit the following
Web site to learn the meaning of the symbols.
http://support.epson.net/symbols
❏Use only the power cord supplied with the printer and do not use the cord with any other equipment. Use of
other cords with this printer or the use of the supplied power cord with other equipment may result in re or
electric shock.
❏Be sure your AC power cord meets the relevant local safety standard.
❏Never disassemble, modify, or attempt to repair the power cord, plug, printer unit, scanner unit, or options by
yourself, except as specically explained in the printer's manuals.
❏Unplug the printer and refer servicing to qualied service personnel under the following conditions:
e power cord or plug is damaged; liquid has entered the printer; the printer has been dropped or the casing
damaged; the printer does not operate normally or exhibits a distinct change in performance. Do not adjust
controls that are not covered by the operating instructions.
❏Place the printer near a wall outlet where the plug can be easily unplugged.
❏Do not place or store the printer outdoors, near excessive dirt or dust, water, heat sources, or in locations
subject to shocks, vibrations, high temperature or humidity.
❏Take care not to spill liquid on the printer and not to handle the printer with wet hands.
❏Keep the printer at least 22 cm away from cardiac pacemakers. Radio waves from this printer may adversely
aect the operation of cardiac pacemakers.
❏If the LCD screen is damaged, contact your dealer. If the liquid crystal solution gets on your hands, wash them
thoroughly with soap and water. If the liquid crystal solution gets into your eyes, ush them immediately with
water. If discomfort or vision problems remain aer a thorough ushing, see a doctor immediately.
❏Avoid using a telephone during an electrical storm. ere may be a remote risk of electric shock from lightning.
❏Do not use a telephone to report a gas leak in the vicinity of the leak.
Safety Instructions for Ink
❏Be careful not to touch any ink when you handle the ink tanks, ink tank caps, and opened ink bottles or ink
bottle caps.
❏If ink gets on your skin, wash the area thoroughly with soap and water.
❏If ink gets into your eyes, ush them immediately with water. If discomfort or vision problems continue aer
a thorough ushing, see a doctor immediately.
❏If ink gets into your mouth, see a doctor right away.
❏Do not disassemble the maintenance box; otherwise ink may get into your eyes or on your skin.
❏Do not shake an ink bottle too vigorously or subject it to strong impacts as this can cause ink to leak.
❏Keep ink bottles and maintenance box out of the reach of children. Do not allow children to drink from the ink
bottles.
Important Instructions
>
Safety Instructions
>
Safety Instructions for Ink
13
Printer Advisories and Warnings
Read and follow these instructions to avoid damaging the printer or your property. Make sure you keep this
manual for future reference.
Advisories and Warnings for Setting Up the Printer
❏Do not block or cover the vents and openings in the printer.
❏Use only the type of power source indicated on the printer's label.
❏Avoid using outlets on the same circuit as photocopiers or air control systems that regularly switch on and o.
❏Avoid electrical outlets controlled by wall switches or automatic timers.
❏Keep the entire computer system away from potential sources of electromagnetic interference, such as
loudspeakers or the base units of cordless telephones.
❏e power-supply cords should be placed to avoid abrasions, cuts, fraying, crimping, and kinking. Do not place
objects on top of the power-supply cords and do not allow the power-supply cords to be stepped on or run over.
Be particularly careful to keep all the power-supply cords straight at the ends and the points where they enter
and leave the transformer.
❏If you use an extension cord with the printer, make sure that the total ampere rating of the devices plugged into
the extension cord does not exceed the cord's ampere rating. Also, make sure that the total ampere rating of all
devices plugged into the wall outlet does not exceed the wall outlet's ampere rating.
❏If you plan to use the printer in Germany, the building installation must be protected by a 10 or 16 amp circuit
breaker to provide adequate short-circuit protection and over-current protection for the printer.
❏When connecting the printer to a computer or other device with a cable, ensure the correct orientation of the
connectors. Each connector has only one correct orientation. Inserting a connector in the wrong orientation
may damage both devices connected by the cable.
❏Place the printer on a at, stable surface that extends beyond the base of the printer in all directions. e printer
will not operate properly if it is tilted at an angle.
❏Allow space above the printer so that you can fully raise the document cover.
❏Leave enough space in front of the printer for the paper to be fully ejected.
❏Avoid places subject to rapid changes in temperature and humidity. Also, keep the printer away from direct
sunlight, strong light, or heat sources.
Advisories and Warnings for Using the Printer
❏Do not insert objects through the slots in the printer.
❏Do not put your hand inside the printer during printing.
❏Do not touch the white at cable and ink tubes inside the printer.
❏Do not use aerosol products that contain ammable gases inside or around the printer. Doing so may cause re.
❏Do not move the print head by hand; otherwise, you may damage the printer.
❏Be careful not to trap your ngers when closing the ADF.
❏Do not press too hard on the scanner glass when placing the originals.
Important Instructions
>
Printer Advisories and Warnings
>
Advisories and Warnings for Using the Printer
14
❏If any of the ink tanks are not lled up to the lower line, rell the ink soon. Prolonged use of the printer when
the ink level is below the lower line could damage the printer.
❏Always turn the printer o using the
P
button. Do not unplug the printer or turn o the power at the outlet
until the
P
light stops ashing.
❏If you are not going to use the printer for a long period, be sure to unplug the power cord from the electrical
outlet.
❏When liing the printer, place your hands in the positions shown below.
Advisories and Warnings for Using the Touchscreen
❏e LCD screen may contain a few small bright or dark spots, and because of its features it may have an uneven
brightness. ese are normal and do not indicate that it is damaged in any way.
❏Only use a dry, so cloth for cleaning. Do not use liquid or chemical cleaners.
❏e exterior cover of the touchscreen could break if it receives a heavy impact. Contact your dealer if the panel
surface chips or cracks, and do not touch or attempt to remove the broken pieces.
❏Press the touchscreen gently with your nger. Do not press force or operate with your nails.
❏Do not use sharp objects such as ball point pens or sharp pencils to perform operations.
❏Condensation inside the touchscreen due to abrupt changes in temperature or humidity may cause
performance to deteriorate.
Advisories and Warnings for Using the Printer with a Wireless
Connection
❏Radio waves from this printer may negatively aect the operation of medical electronic equipment, causing
them to malfunction. When using this printer inside medical facilities or near medical equipment, follow
directions from the authorized personnel representing the medical facilities, and follow all posted warnings and
directions on the medical equipment.
❏Radio waves from this printer may negatively aect the operation of automatically controlled devices such as
automatic doors or re alarms, and could lead to accidents due to malfunction. When using this printer near
automatically controlled devices, follow all posted warnings and directions on these devices.
Important Instructions
>
Printer Advisories and Warnings
>
Advisories and Warnings for Using the Printer with
…
15
Advisories and Warnings for Transporting or Storing the Printer
❏When storing or transporting the printer, avoid tilting it, placing it vertically, or turning it upside down;
otherwise ink may leak.
❏Before transporting the printer, make sure that the print head is in the home (far right) position.
Protecting Your Personal Information
When you give the printer to someone else or dispose of it, erase all the personal information stored in the printer's
memory by selecting Settings > Restore Default Settings > Clear All Data and Settings on the control panel.
Important Instructions
>
Protecting Your Personal Information
16
Front
AADF (Automatic Document
Feeder)
Feeds originals automatically.
BADF cover Open when removing originals jammed in the ADF.
CADF input tray Supports loaded originals.
DADF edge guide Feeds originals straight into the printer. Slide to the edges of the originals.
EADF document support Supports originals.
FADF output tray Holds originals ejected from the ADF.
AControl panel Indicates the printer's status and allows you to make print settings.
BInk tank cover Open to rell the ink tank.
CInk tank cap Open to rell the ink tank.
DInk tank Contains the ink tank.
Part Names and Functions
>
Front
18
EPaper cassette cover Open to load paper in the paper cassette.
FFront cover Open when removing jammed paper.
GOutput tray Holds the ejected paper.
Inside
ADocument cover Blocks external light while scanning.
BScanner glass Place the originals.
CPrint head Ink is ejected from the print head nozzles underneath.
DEdge guide Feeds the paper straight into the printer. Slide to the edges of the paper.
EPaper cassette Loads paper.
FOutput switch lever Raise to output paper to the output tray. Lower to output paper facing up to
the front of the printer.
GPrinter cover Open when removing jammed paper.
Part Names and Functions
>
Inside
19
Rear
AStopper Position the stopper to prevent print outs from falling from the output tray.
BLAN port Connects a LAN cable.
CUSB port Connects a USB cable to connect with a computer.
DLINE port
*
Connects a phone line.
EEXT. port
*
Connects external phone devices.
FAC inlet Connects the power cord.
GRear paper feed slot Loads paper.
HRear cover Remove when removing jammed paper.
IMaintenance box cover Open when replacing the maintenance box.
* Only for ET-5170 Series/L6490 Series
Part Names and Functions
>
Rear
20
Guide to the Control Panel
Control Panel.....................................................22
Touch Screen Operations.............................................22
Home Screen Conguration.......................................... 23
Menu Screen Conguration...........................................25
Entering Characters................................................ 26
Viewing Animations................................................26
Control Panel
ATurns the printer on or o.
Unplug the power cord after checking that the power light is o.
BDisplays the home screen.
CDisplays menus and messages.
DDisplays the solutions when you are in trouble.
E
*
Turns on when received documents that have not yet been read, printed, or saved, are stored in the printer's
memory.
* Only for ET-5170 Series/L6490 Series
Touch Screen Operations
e touchscreen is compatible with the following operations.
Tap Press or select the items or the icons.
Flick Scroll the screen swiftly.
Guide to the Control Panel
>
Touch Screen Operations
22
Slide Hold and move the items around.
Pinch in
Pinch out
Zoom in or zoom out of the preview image on the control panel when printing
photos.
Home Screen Conguration
ADisplays the Remaining capacity of Maintenance box screen. You can check the approximate
service life of maintenance box.
BDisplays the network connection status. See the following for more details.
“Guide to the Network Icon” on page 24
Guide to the Control Panel
>
Home Screen Conguration
23
CDisplays the Device Sound Settings screen. You can set Mute and Quiet Mode. You can also
access the Sound menu from this screen. You can also make this setting from the Settings
menu.
Settings > General Settings > Basic Settings > Sound
Indicates whether or not Quiet Mode is set for the printer. When this feature is
enabled, the noise made by printer operations is reduced, but print speed may slow
down. However, noises may not be reduced depending on the selected paper type
and print quality.
Indicates that Mute is set for the printer.
DDisplays the Fax Data Information screen.
The number displayed indicates the number of faxes that have not yet been read, printed, or
saved.
EDisplays each menu.
❏Copy
Allows you to copy documents.
❏Scan
Allows you to scan documents and save them to a computer.
❏Fax
Allows you to send faxes.
❏Maintenance
Displays the menus recommended to improve the quality of your printouts such as unclogging nozzles by printing
a nozzle check pattern and performing head cleaning, and improving blurring or banding in your printouts by
aligning the print head. You can also make this setting from the Settings menu.
Settings > Maintenance
❏Settings
Allows you to make settings related to maintenance, printer settings, and operations.
FScrolls the screen to the right.
Guide to the Network Icon
The printer is not connected to a wired (Ethernet) network or unset it.
The printer is connected to a wired (Ethernet) network.
The printer is not connected to a wireless (Wi-Fi) network.
The printer is searching for SSID, unset IP address, or having a problem with a wireless
(Wi-Fi) network.
The printer is connected to a wireless (Wi-Fi) network.
The number of bars indicates the signal strength of the connection. The more bars
there are, the stronger the connection.
The printer is not connected to a wireless (Wi-Fi) network in Wi-Fi Direct (Simple AP)
mode.
Guide to the Control Panel
>
Home Screen Conguration
>
Guide to the Network Icon
24
The printer is connected to a wireless (Wi-Fi) network in Wi-Fi Direct (Simple AP) mode.
Menu Screen Conguration
AReturns to the previous screen.
BSwitches the list of settings using the tabs. The Advanced Settings tab displays other items that you can set as
necessary.
CDisplays the list of setting items. When is displayed, you view additional information by selecting the icon. Make
settings by selecting the item or adding a check mark.
Grayed out items are not available. Select the item to check why it is unavailable.
If any problems occur, is displayed on the item. Select the icon to check how to solve the problem.
DStarts operations using the current settings. Items vary depending on the menu.
Copies Displays the on-screen keypad allowing you to enter the number of copies.
x
Starts printing, copying, scanning, or sending faxes.
Guide to the Control Panel
>
Menu Screen Conguration
25
Entering Characters
You can enter characters and symbols by using on-screen keyboard when you make network settings and so on.
AIndicates the character count.
BMoves the cursor to the input position.
CSwitches between upper case and lower case.
DSwitches the character type.
ABC: Alphabet
123#: Numbers and symbols
EEnters frequently used email domain addresses or URLs by simply selecting the item.
FEnters a space.
GEnters character.
HDeletes a character to the left. Deletes a character to the right when the cursor is at the start of the line and there are
no characters to the left.
Viewing Animations
You can view animations of operating instructions such as loading paper or removing jammed paper on the LCD
screen.
❏Select : Displays the help screen. Select How To and select the items that you want to view.
Guide to the Control Panel
>
Viewing Animations
26
Loading Paper
Paper Handling Precautions.......................................... 29
Paper Size and Type Settings..........................................29
Loading Paper.................................................... 31
Loading Various Paper.............................................. 32
Outputting Paper.................................................. 33
Paper Handling Precautions
❏Read the instruction sheets supplied with the paper.
❏To achieve high-quality printouts with genuine Epson paper, use the paper in the environment stated on the
sheets supplied with the paper.
❏Fan and align the edges of the paper before loading. Do not fan or curl photo paper. Doing so may damage the
printable side.
❏If the paper is curled, atten it or curl it slightly in the opposite direction before loading. Printing on curled
paper may cause paper jams and smears on the printout.
❏Paper feed problems may occur frequently for manual 2-sided printing when printing on one side of pre-
printed paper. Reduce the number of sheets to half or less, or load one sheet of paper at a time if paper jams
continue.
❏Make sure you are using long-grain paper. If you are not sure what type of paper you are using, check the paper
packaging or contact the manufacturer to conrm the paper specications.
❏Fan and align the edges of the envelopes before loading. When the stacked envelopes are pued up with air,
press them down to atten them before loading.
Related Information
&“Unavailable Paper Types” on page 241
Paper Size and Type Settings
If you register the paper size and type on the screen displayed when you load paper, the printer informs you when
the registered information and print settings dier. is prevents you from wasting paper and ink by making sure
Loading Paper
>
Paper Size and Type Settings
29
you are not printing on the wrong paper size or printing in the wrong color due to using settings that do not match
the paper type.
is screen is not displayed if you have disabled Paper Setup Auto Display. If you disable this feature, you cannot
print from an iPhone, iPad, or iPod touch using AirPrint.
If displayed paper size and type dier from the loaded paper, select the item to change. If the settings match the
loaded paper, close the screen.
Note:
You can also display the paper size and paper type settings screen by selecting Settings > General Settings > Printer
Settings > Paper Source Settings > Paper Setting.
Related Information
&“Paper Setup Auto Display:” on page 253
List of Paper Type
To obtain optimum printing results, select the paper type that suits the paper.
Media Name Media Type
Control Panel Printer Driver
Epson Bright White Ink Jet Paper Plain paper Plain paper
Epson Ultra Glossy Photo Paper Ultra Glossy Epson Ultra Glossy
Epson Premium Glossy Photo Paper Prem. Glossy Epson Premium Glossy
Epson Premium Semigloss Photo
Paper
Prem. Semigloss Epson Premium Semigloss
Epson Photo Paper Glossy Glossy Photo Paper Glossy
Epson Matte Paper-Heavyweight
Epson Double-Sided Matte Paper
Matte Epson Matte
Epson Photo Quality Ink Jet Paper
Epson Double-sided Photo Quality Ink
Jet Paper
Epson Photo Quality Self Adhesive
Sheets
Photo Quality IJ Epson Photo Quality Ink Jet
Loading Paper
>
Paper Size and Type Settings
>
List of Paper Type
30
Loading Paper
You can load paper by referring to the animations displayed on the printer's LCD screen.
Select , and then select How To > Load paper.
Select the paper source you want to use to display the animations.
Select Finish to close the animation screen.
Precautions when Loading Letterhead Paper
❏For letterhead paper, select Letterhead as the paper type.
❏For letterhead paper, if you print on paper that is smaller than the setting in the printer driver, the printer may
print beyond the edges of the paper which can lead to ink smears on your printouts and excess ink building up
inside the printer. Make sure you select the correct paper size setting.
❏2-sided printing is not available for letterhead paper. Also, the print speed may be slower.
Loading Paper
>
Loading Paper
>
Precautions when Loading Letterhead Paper
31
Loading Various Paper
Loading Envelopes
Rear Paper Feed Slot
Load an envelope at the center of the rear paper feed slot short edge rst with the ap facing down, and slide the
edge guides to the edges of the envelope.
Note:
We recommend lowering the output switch lever to output the envelope to the front of the printer.
Paper Cassette
Load envelopes in the paper cassette with the ap facing up, and then slide the edge guides to the edges of the
envelopes.
Loading Paper
>
Loading Various Paper
>
Loading Envelopes
32
Loading Pre-punched Paper
Load a single sheet of pre-punched paper at the center of the rear paper feed slot with the printable side facing up.
Adjust the print position of your le to avoid printing over the holes.
Outputting Paper
❏Printed paper is ejected to the output tray with the printed side facing down. For A4 size plain paper (with a
thickness of 80g/m²), up to 100 sheets can be ejected at a time. Outputting more than 100 sheets may cause
paper to fall or a paper jam to occur. Remove any excess paper so that it does not exceed the maximum number
of sheets that can be ejected.
❏When you load thick paper, photo paper, or business card size paper, lower the output switch lever to output
paper to the front of the printer. We also recommend outputting envelopes to the front of the printer.
❏Avoid touching the printed surface of the photo paper with your bare hands. Moisture and oils from your hands
can aect print quality.
Loading Paper
>
Outputting Paper
33
Placing Originals
Place originals on the scanner glass or the ADF.
You can place multiple originals in the ADF.
Follow the steps below to view the animations for placing originals.
Select , and then select How To > Place Originals. Select the method of placing originals that you want to view.
Select Finish to close the animation screen.
When using the scanner glass
!
Caution:
Be careful not to trap your ngers when closing the document cover. Otherwise you may be injured.
c
Important:
❏When placing bulky originals such as books, prevent exterior light from shining directly onto the scanner glass.
❏Do not apply too much force to the scanner glass or the document cover. Otherwise, they may be damaged.
Note:
❏If there is any trash or dirt on the scanner glass, the scanning range may expand to include it, so the image of the original
may be displaced or reduced. Remove any trash and dirt on the scanner glass before scanning.
❏A range of 1.5 mm from the corner of the scanner glass is not scanned.
❏When originals are placed in the ADF and on the scanner glass, priority is given to the originals in the ADF.
❏If you leave the originals on the scanner glass for a long time, they may stick to the surface of the glass.
Placing Originals
>
Placing Originals
35
When using the ADF
c
Important:
❏Do not load originals above the line just under the triangle symbol inside the ADF edge guide.
❏Do not add originals while scanning.
Related Information
&“Originals that are not Supported by the ADF” on page 36
&“Scanner Specications” on page 265
Originals that are not Supported by the ADF
c
Important:
Do not feed photographs or valuable original artwork into the ADF. Misfeeding may wrinkle or damage the
original. Scan these documents on the scanner glass instead.
To prevent paper jams, avoid placing the following originals in the ADF. For these types, use the scanner glass.
❏Originals that are torn, folded, wrinkled, deteriorated, or curled
❏Originals with binder holes
❏Originals held together with tape, staples, paper clips etc.
❏Originals that have stickers or labels stuck to them
❏Originals that are cut irregularly or not right angled
❏Originals that are bound
❏OHPs, thermal transfer paper, or carbon backs
Placing Originals
>
Originals that are not Supported by the ADF
36
Printing Documents
Printing from a Computer - Windows
Printing Using Easy Settings
Note:
Operations may dier depending on the application. See the application's help for details.
1. Load paper in the printer.
“Loading Paper” on page 31
2. Open the le you want to print.
3. Select Print or Print Setup from the File menu.
4. Select your printer.
Printing
>
Printing Documents
>
Printing from a Computer - Windows
38
5. Select Preferences or Properties to access the printer driver window.
6. Change the settings as necessary.
You can see the online help for explanations of the setting items. Right-clicking an item displays Help.
7. Click OK to close the printer driver window.
8. Click Print.
Related Information
&“Available Paper and Capacities” on page 239
&“List of Paper Type” on page 30
Adding Printing Presets for Easy Printing
If you create your own preset of frequently used print settings on the printer driver, you can print easily by
selecting the preset from the list.
Printing
>
Printing Documents
>
Printing from a Computer - Windows
39
1. On the printer driver's Main or More Options tab, set each item (such as Document Size and Paper Type).
2. Click Add/Remove Presets in Printing Presets.
3. Enter a Name and, if necessary, enter a comment.
4. Click Save.
Note:
To delete an added preset, click Add/Remove Presets, select the preset name you want to delete from the list, and then
delete it.
5. Click Print.
e next time you want to print using the same settings, select the registered setting name from Printing Presets,
and click OK.
Related Information
&“Loading Paper” on page 31
&“Printing Using Easy Settings” on page 38
Printing on 2-Sides
You can print on both sides of the paper.
Note:
❏If you do not use paper that is suitable for 2-sided printing, the print quality may decline and paper jams may occur.
“Paper for 2-Sided Printing” on page 241
❏Depending on the paper and the data, ink may bleed through to the other side of the paper.
❏However, it may not be available when the printer is accessed over a network or is used as a shared printer.
1. On the printer driver's Main tab, select the method of 2-Sided Printing.
2. Click Settings, make the appropriate settings, and then click OK.
3. Click Print Density, make the appropriate settings, and then click OK.
When setting Print Density, you can adjust print density according to the document type.
Printing
>
Printing Documents
>
Printing from a Computer - Windows
40
Note:
Printing may be slow depending on the combination of options selected for Select Document Type in the Print Density
Adjustment window and for Quality on the Main tab.
4. Set the other items on the Main and More Options tabs as necessary, and then click OK.
5. Click Print.
Related Information
&“Available Paper and Capacities” on page 239
&“Loading Paper” on page 31
&“Printing Using Easy Settings” on page 38
Printing a Booklet
You can also print a booklet that can be created by re-ordering the pages and folding the printout.
Note:
❏If you do not use paper that is suitable for 2-sided printing, the print quality may decline and paper jams may occur.
“Paper for 2-Sided Printing” on page 241
❏Depending on the paper and the data, ink may bleed through to the other side of the paper.
❏However, it may not be available when the printer is accessed over a network or is used as a shared printer.
1. On the printer driver's Main tab, select the type of long-edge binding you want to use from 2-Sided Printing.
2. Click Settings, select Booklet, and then select Center Binding or Side Binding.
❏Center Binding: Use this method when printing a small number of pages that can be stacked and easily
folded in half.
❏Side Binding. Use this method when printing one sheet (four pages) at a time, folding each in half, and then
putting them together in one volume.
3. Click OK.
Printing
>
Printing Documents
>
Printing from a Computer - Windows
41
4. When printing data that has a lot of photos and images, click Print Density, and then make the appropriate
settings, and then click OK.
When setting Print Density, you can adjust print density according to the document type.
Note:
Printing may be slow depending on the combination of options selected for Select Document Type in the Print Density
Adjustment window and for Quality on the Main tab.
5. Set the other items on the Main and More Options tabs as necessary, and then click OK.
6. Click Print.
Related Information
&“Available Paper and Capacities” on page 239
&“Loading Paper” on page 31
&“Printing Using Easy Settings” on page 38
Printing Several Pages on One Sheet
You can print several pages of data on a single sheet of paper.
1. On the printer driver's Main tab, select 2-Up, 4-Up, 6-Up, 8-Up, 9-Up, or 16-Up as the Multi-Page setting.
2. Click Layout Order, make the appropriate settings, and then click OK.
3. Set the other items on the Main and More Options tabs as necessary, and then click OK.
4. Click Print.
Related Information
&“Loading Paper” on page 31
&“Printing Using Easy Settings” on page 38
Printing
>
Printing Documents
>
Printing from a Computer - Windows
42
Printing to Fit the Paper Size
Select the paper size you loaded in the printer as the Destination Paper Size setting.
1. On the printer driver's More Options tab, make the following settings.
❏Document Size: Select the size of the paper you set in the application setting.
❏Output Paper: Select the paper size you loaded in the printer.
Fit to Page is automatically selected.
Note:
Click Center to print the reduced image in the middle of the paper.
2. Set the other items on the Main and More Options tabs as necessary, and then click OK.
3. Click Print.
Related Information
&“Loading Paper” on page 31
&“Printing Using Easy Settings” on page 38
Printing
>
Printing Documents
>
Printing from a Computer - Windows
43
Printing a Reduced or Enlarged Document at any Magnication
You can reduce or enlarge the size of a document by a specic percentage.
1. On the printer driver's More Options tab, select the document size from the Document Size setting.
2. Select the paper size you want to print on from the Output Paper setting.
3. Select Reduce/Enlarge Document, Zoom to, and then enter a percentage.
4. Set the other items on the Main and More Options tabs as necessary, and then click OK.
5. Click Print.
Related Information
&“Loading Paper” on page 31
&“Printing Using Easy Settings” on page 38
Printing One Image on Multiple Sheets for Enlargement (Creating a Poster)
is feature allows you to print one image on multiple sheets of paper. You can create a larger poster by taping
them together.
1. On the printer driver's Main tab, select 2x1 Poster, 2x2 Poster, 3x3 Poster, or 4x4 Poster as the Multi-Page
setting.
Printing
>
Printing Documents
>
Printing from a Computer - Windows
44
2. Click Settings, make the appropriate settings, and then click OK.
Note:
Print Cutting Guides allows you to print a cutting guide.
3. Set the other items on the Main and More Options tabs as necessary, and then click OK.
4. Click Print.
Related Information
&“Loading Paper” on page 31
&“Printing Using Easy Settings” on page 38
Making Posters Using Overlapping Alignment Marks
Here is an example of how to make a poster when 2x2 Poster is selected, and Overlapping Alignment Marks is
selected in Print Cutting Guides.
Printing
>
Printing Documents
>
Printing from a Computer - Windows
45
1. Prepare Sheet 1 and Sheet 2. Cut o the margins of Sheet 1 along the vertical blue line through the center of
the top and bottom cross marks.
2. Place the edge of Sheet 1 on top of Sheet 2 and align the cross marks, then temporarily tape the two sheets
together from the back.
Printing
>
Printing Documents
>
Printing from a Computer - Windows
46
3. Cut the taped sheets in two along the vertical red line through the alignment markers (this time, the line to the
le of the cross marks).
4. Tape the sheets together from the back.
5. Repeat steps 1 to 4 to tape Sheet 3 and Sheet 4 together.
Printing
>
Printing Documents
>
Printing from a Computer - Windows
47
6. Cut o the margins of Sheet 1 and Sheet 2 along the horizontal blue line through the center of the le and right
side cross marks.
7. Place the edge of Sheet 1 and Sheet 2 on top of Sheet 3 and Sheet 4 and align the cross marks, and then
temporarily tape them together from the back.
Printing
>
Printing Documents
>
Printing from a Computer - Windows
48
10. Cut o the remaining margins along the outer guide.
Printing with a Header and Footer
You can print information such as a user name and printing date in headers or footers.
1. On the printer driver's More Options tab, click Watermark Features, and then select Header/Footer.
Printing
>
Printing Documents
>
Printing from a Computer - Windows
50
2. Settings, and then select the items you want to print and then click OK.
Note:
❏To specify the rst page number, select Page Number from the position you want to print in the header or footer, and
then select the number in Starting number.
❏If you want to print text in the header or footer, select the position you want to print, and then select Text. Enter the
text you want to print in the text input eld.
3. Set the other items on the Main and More Options tabs as necessary, and then click OK.
4. Click Print.
Related Information
&“Loading Paper” on page 31
&“Printing Using Easy Settings” on page 38
Printing a Watermark
You can print a watermark such as "Condential" or an anti-copy pattern on your printouts. If you print with an
anti-copy pattern, the hidden letters appear when photocopied in order to distinguish the original from the copies.
Anti-Copy Pattern is available under the following conditions:
❏Paper Type: Plain paper, Letterhead, or ick paper
❏Quality: Standard
❏2-Sided Printing: O
❏Color Correction: Automatic
❏Short Grain Paper: Not selected
Note:
You can also add your own watermark or anti-copy pattern.
1. On the printer driver's More Options tab, click Watermark Features, and then select Anti-Copy Pattern or
Watermark.
2. Click Settings to change details such as the size, density, or position of the pattern or the mark.
3. Set the other items on the Main and More Options tabs as necessary, and then click OK.
4. Click Print.
Related Information
&“Loading Paper” on page 31
Printing
>
Printing Documents
>
Printing from a Computer - Windows
51
&“Printing Using Easy Settings” on page 38
Printing Multiple Files Together
Job Arranger Lite allows you to combine several les created by dierent applications and print them as a single
print job. You can specify the print settings for combined les, such as multi-page layout, and 2-sided printing.
1. On the printer driver's Main tab, select Job Arranger Lite.
2. Click Print.
When you start printing, the Job Arranger Lite window is displayed.
3. With the Job Arranger Lite window opened, open the le that you want to combine with the current le, and
then repeat the above steps.
4. When you select a print job added to Print Project Lite in the Job Arranger Lite window, you can edit the page
layout.
5. Click Print from the File menu to start printing.
Note:
If you close the Job Arranger Lite window before adding all the print data to the Print Project, the print job you are
currently working on is canceled. Click Save from the File menu to save the current job. e extension of the saved les
is "ecl".
To open a Print Project, click Job Arranger Lite on the printer driver's Maintenance tab to open the Job Arranger Lite
window. Next, select Open from the File menu to select the le.
Related Information
&“Loading Paper” on page 31
&“Printing Using Easy Settings” on page 38
Printing Using the Color Universal Print Feature
You can enhance the visibility of texts and images in printouts.
Printing
>
Printing Documents
>
Printing from a Computer - Windows
52
Color Universal Print is only available when the following settings are selected.
❏Paper Type: Plain paper, Letterhead, or ick paper
❏Quality: Standard or a higher quality
❏Color: Color
❏Applications: Microso® Oce 2007 or later
❏Text Size: 96 pts or smaller
1. On the printer driver's More Options tab, click Image Options in the Color Correction setting.
2. Select an option from the Color Universal Print setting.
3. Enhancement Options to make further settings.
4. Set the other items on the Main and More Options tabs as necessary, and then click OK.
5. Click Print.
Note:
❏Certain characters may be altered by patterns, such as "+" appearing as "±".
❏Application-specic patterns and underlines may alter content printed using these settings.
❏Print quality may decrease in photos and other images when using Color Universal Print settings.
❏Printing is slower when using Color Universal Print settings.
Related Information
&“Loading Paper” on page 31
&“Printing Using Easy Settings” on page 38
Adjusting the Print Color
You can adjust the colors used in the print job. ese adjustments are not applied to the original data.
PhotoEnhance produces sharper images and more vivid colors by automatically adjusting the contrast, saturation,
and brightness of the original image data.
Note:
PhotoEnhance adjusts the color by analyzing the location of the subject. erefore, if you have changed the location of the
subject by reducing, enlarging, cropping, or rotating the image, the color may change unexpectedly. If the image is out of
focus, the tone may be unnatural. If the color is changed or becomes unnatural, print in a mode other than PhotoEnhance.
1. On the printer driver's More Options tab, select the method of color correction from the Color Correction
setting.
❏Automatic: is setting automatically adjusts the tone to match the paper type and print quality settings.
Printing
>
Printing Documents
>
Printing from a Computer - Windows
53
❏Custom: Click Advanced, you can make your own settings.
2. Set the other items on the Main and More Options tabs as necessary, and then click OK.
3. Click Print.
Related Information
&“Loading Paper” on page 31
&“Printing Using Easy Settings” on page 38
Printing to Emphasize Thin Lines
You can thicken thin lines that are too thin to print.
1. On the printer driver's More Options tab, click Image Options in the Color Correction setting.
2. Select Emphasize in Lines.
3. Set the other items on the Main and More Options tabs as necessary, and then click OK.
4. Click Print.
Related Information
&“Loading Paper” on page 31
&“Printing Using Easy Settings” on page 38
Printing Clear Bar Codes
You can print a bar code clearly and make it easy to scan. Only enable this feature if the bar code you printed
cannot be scanned.
You can use this feature under the following conditions.
❏Paper Type: Plain paper, Letterhead, ick paper, Epson Matte, or Envelope
Printing
>
Printing Documents
>
Printing from a Computer - Windows
54
❏Quality: Standard
1. On the printer driver's Maintenance tab, click Extended Settings, and then select Barcode mode.
2. Set the other items on the Main and More Options tabs as necessary, and then click OK.
3. Click Print.
Note:
Deblurring may not always be possible depending on the circumstances.
Related Information
&“Loading Paper” on page 31
&“Printing Using Easy Settings” on page 38
Printing from a Computer - Mac OS
Printing Using Easy Settings
Note:
Operations and screens dier depending on the application. See the application's help for details.
1. Load paper in the printer .
“Loading Paper” on page 31
2. Open the le you want to print.
3. Select Print from the File menu or another command to access the print dialog.
If necessary, click Show Details or
d
to expand the print window.
4. Select your printer.
Printing
>
Printing Documents
>
Printing from a Computer - Mac OS
55
5. Select Print Settings from the pop-up menu.
6. Change the settings as necessary.
7. Click Print.
Related Information
&“Available Paper and Capacities” on page 239
&“List of Paper Type” on page 30
Adding Printing Presets for Easy Printing
If you create your own preset of frequently used print settings on the printer driver, you can print easily by
selecting the preset from the list.
1. Set each item such as Print Settings and Layout (Paper Size, Media Type, and so on).
Printing
>
Printing Documents
>
Printing from a Computer - Mac OS
56
2. Click Presets to save the current settings as a preset.
3. Click OK.
Note:
To delete an added preset, click Presets > Show Presets, select the preset name you want to delete from the list, and then
delete it.
4. Click Print.
e next time you want to print using the same settings, select the registered preset name from the Presets.
Related Information
&“Loading Paper” on page 31
&“Printing Using Easy Settings” on page 55
Printing on 2-Sides
You can print on both sides of the paper.
Note:
❏If you do not use paper that is suitable for 2-sided printing, the print quality may decline and paper jams may occur.
“Paper for 2-Sided Printing” on page 241
❏Depending on the paper and the data, ink may bleed through to the other side of the paper.
1. Select Two-sided Printing Settings from the pop-up menu.
2. Select the bindings in Two-sided Printing.
3. Select the type of original in Document Type.
Note:
❏Printing may be slow depending on the Document Type setting.
❏If you are printing high-density data such as photos or graphs, select Text & Photo s or Te xt & Graphi c s as the
Document Type setting. If scung occurs or the image bleeds through to the reverse side, adjust the print density
and ink drying time by clicking the arrow mark next to Adjustments.
4. Set the other items as necessary.
Printing
>
Printing Documents
>
Printing from a Computer - Mac OS
57
5. Click Print.
Related Information
&“Available Paper and Capacities” on page 239
&“Loading Paper” on page 31
&“Printing Using Easy Settings” on page 55
Printing Several Pages on One Sheet
You can print several pages of data on a single sheet of paper.
1. Select Layout from the pop-up menu.
2. Set the number of pages in Pages per Sheet, the Layout Direction (page order), and Border.
3. Set the other items as necessary.
4. Click Print.
Related Information
&“Loading Paper” on page 31
&“Printing Using Easy Settings” on page 55
Printing
>
Printing Documents
>
Printing from a Computer - Mac OS
58
Printing to Fit the Paper Size
Select the paper size you loaded in the printer as the Destination Paper Size setting.
1. Select the size of the paper you set in the application as the Paper Size setting.
2. Select Paper Handling from the pop-up menu.
3. Select Scale to t paper size.
4. Select the paper size you loaded in the printer as the Destination Paper Size setting.
5. Set the other items as necessary.
6. Click Print.
Related Information
&“Loading Paper” on page 31
&“Printing Using Easy Settings” on page 55
Printing a Reduced or Enlarged Document at any Magnication
You can reduce or enlarge the size of a document by a specic percentage.
Printing
>
Printing Documents
>
Printing from a Computer - Mac OS
59
1. Select Print from the File menu or another command to access the print dialog.
2. Select Page Setup from the File menu of the application.
3. Select Printer, Paper Size, enter percentage in Scale, and then click OK.
Note:
Select the paper size you set in the application as the Paper Size setting.
4. Set the other items as necessary.
5. Click Print.
Related Information
&“Loading Paper” on page 31
&“Printing Using Easy Settings” on page 55
Adjusting the Print Color
You can adjust the colors used in the print job. ese adjustments are not applied to the original data.
PhotoEnhance produces sharper images and more vivid colors by automatically adjusting the contrast, saturation,
and brightness of the original image data.
Note:
PhotoEnhance adjusts the color by analyzing the location of the subject. erefore, if you have changed the location of the
subject by reducing, enlarging, cropping, or rotating the image, the color may change unexpectedly. If the image is out of
focus, the tone may be unnatural. If the color is changed or becomes unnatural, print in a mode other than PhotoEnhance.
1. Select Color Matching from the pop-up menu, and then select EPSON Color Controls.
2. Select Color Options from the pop-up menu, and then select one of the available options.
3. Click the arrow next to Advanced Settings and make the appropriate settings.
4. Set the other items as necessary.
5. Click Print.
Related Information
&“Loading Paper” on page 31
&“Printing Using Easy Settings” on page 55
Printing
>
Printing Documents
>
Printing from a Computer - Mac OS
60
Printing Documents from Smart Devices (iOS)
You can print documents from a smart device such as a smartphone or tablet.
Printing Documents Using Epson Smart Panel
Note:
Operations may dier depending on the device.
1. Set up your printer for wireless printing.
2. If Epson Smart Panel is not installed, install it.
“Application for Easily Operating the Printer from a Smart device (Epson Smart Panel)” on page 246
3. Connect your smart device to the wireless router.
4. Start Epson Smart Panel.
5. Select the print document menu on the home screen.
6. Select the document you want to print.
7. Start printing.
Printing Documents Using AirPrint
AirPrint enables instant wireless printing from iPhone, iPad, iPod touch, and Mac without the need to install
drivers or download soware.
Note:
If you disabled paper conguration messages on your printer control panel, you cannot use AirPrint. See the link below to
enable the messages, if necessary.
1. Set up your printer for wireless printing. See the link below.
http://epson.sn
2. Connect your Apple device to the same wireless network that your printer is using.
Printing
>
Printing Documents
>
Printing Documents from Smart Devices (iOS)
61
3. Print from your device to your printer.
Note:
For details, see the AirPrint page on the Apple website.
Related Information
&“Cannot Print Even ough a Connection has been Established (iOS)” on page 155
Printing Documents from Smart Devices (Android)
You can print documents from a smart device such as a smartphone or tablet.
Printing Documents Using Epson Smart Panel
Note:
Operations may dier depending on the device.
1. Set up your printer for wireless printing.
2. If Epson Smart Panel is not installed, install it.
“Application for Easily Operating the Printer from a Smart device (Epson Smart Panel)” on page 246
3. Connect your smart device to the wireless router.
4. Start Epson Smart Panel.
5. Select the print document menu on the home screen.
6. Select the document you want to print.
7. Start printing.
Printing Documents Using Epson Print Enabler
You can wirelessly print your documents, emails, photos, and web pages right from your Android phone or tablet
(Android v4.4 or later). With a few taps, your Android device will discover an Epson printer that is connected to
the same wireless network.
Note:
Operations may dier depending on the device.
1. Set up your printer for wireless printing.
Printing
>
Printing Documents
>
Printing Documents from Smart Devices (Android)
62
2. On your Android device, install the Epson Print Enabler plug-in from Google Play.
3. Connect your Android device to the same wireless network as your printer.
4. Go to Settings on your Android device, select Printing, and then enable Epson Print Enabler.
5. From an Android application such as Chrome, tap the menu icon and print whatever is on the screen.
Note:
If you do not see your printer, tap All Printers and select your printer.
Printing Using Mopria Print Service
Mopria Print Service enables instant wireless printing from Android smart phones or tablets.
1. Install Mopria Print Service from Google Play.
2. Load paper in the printer.
3. Set up your printer for wireless printing. See the link below.
http://epson.sn
4. Connect your Android device to the same wireless network that your printer is using.
5. Print from your device to your printer.
Note:
For more details, access the Mopria Web site at https://mopria.org.
Related Information
&“Loading Paper” on page 31
Printing on Envelopes
Printing on Envelopes from a Computer (Windows)
1. Load envelopes in the printer.
“Loading Paper” on page 31
2. Open the le you want to print.
3. Access the printer driver window.
Printing
>
Printing on Envelopes
>
Printing on Envelopes from a Computer (Windows)
63
4. Select the envelope size from Document Size on the Main tab, and then select Envelope from Paper Type.
5. Set the other items on the Main and More Options tabs as necessary, and then click OK.
6. Click Print.
Printing on Envelopes from a Computer (Mac OS)
1. Load envelopes in the printer.
“Loading Paper” on page 31
2. Open the le you want to print.
3. Select Print from the File menu or another command to access the print dialog.
4. Select the size as the Paper Size setting.
5. Select Print Settings from the pop-up menu.
6. Select Envelope as the Media Type setting.
7. Set the other items as necessary.
8. Click Print.
Printing Web Pages
Printing Web Pages from a Computer
Epson Photo+ allows you to display web pages, crop the specied area, and then edit and print them. See the
application’s help for details.
Printing Web Pages from Smart Devices
Note:
Operations may dier depending on the device.
1. Load paper in the printer.
“Loading Paper” on page 31
2. Set up your printer for wireless printing.
3. If Epson Smart Panel is not installed, install it.
“Application for Easily Operating the Printer from a Smart device (Epson Smart Panel)” on page 246
Printing
>
Printing Web Pages
>
Printing Web Pages from Smart Devices
64
4. Connect your smart device to the same wireless network as your printer.
5. Open the web page you want to print in your web browser app.
6. Tap Share from the menu of the web browser application.
7. Select Smart Panel.
8. Tap Print.
Printing Using a Cloud Service
By using Epson Connect service available on the Internet, you can print from your smartphone, tablet PC, or
laptop, anytime and practically anywhere. To use this service, you need to register the user and the printer in
Epson Connect.
e features available on the Internet are as follows.
❏Email Print
When you send an email with attachments such as documents or images to an email address assigned to the
printer, you can print that email and the attachments from remote locations such as your home or oce printer.
❏Epson iPrint
is Application is for iOS and Android, and allows you to print or scan from a smartphone or tablet. You can
print documents, images, and web sites by sending them directly to a printer on the same wireless LAN.
❏Remote Print Driver
is is a shared driver supported by Remote Print Driver. When printing using a printer in a remote location,
you can print by changing the printer on the usual applications window.
See the Epson Connect web portal for details on how to setup or print.
Printing
>
Printing Using a Cloud Service
65
https://www.epsonconnect.com/
http://www.epsonconnect.eu (Europe only)
Registering to Epson Connect Service from the Control Panel
Follow the steps below to register the printer.
1. Select Settings on the control panel.
2. Select General Settings > Web Service Settings > Epson Connect Services > Unregister to print the
registration sheet.
3. Follow the instructions on the registration sheet to register the printer.
Printing
>
Printing Using a Cloud Service
>
Registering to Epson Connect Service from the Control Panel
66
Available Copying Methods
Place the originals on the scanner glass or the ADF, and then select the Copy menu on the home screen.
Copying Originals
You can copy the originals of xed size or custom size by color or monochrome.
1. Load paper in the printer.
“Loading Paper” on page 31
2. Place the originals.
“Placing Originals” on page 35
3. Select Copy on the home screen.
4. Select the Copy tab, and then select B&W or Color.
5. Tap
x
.
Copying
>
Available Copying Methods
>
Copying Originals
68
Copying on 2-Sides
Copy multiple originals on both sides of the paper.
1. Place all originals face up in the ADF.
“Placing Originals” on page 35
c
Important:
If you want to copy originals that are not supported by the ADF, use the scanner glass.
“Originals that are not Supported by the ADF” on page 36
Note:
You can also place the originals on the scanner glass.
“Placing Originals” on page 35
2. Select Copy on the home screen.
3. Select the Copy tab, and then select (2-Sided) > 1→2-Sided.
4. Specify the original orientation and the binding position, and then select OK.
5. Tap
x
.
Copying by Enlarging or Reducing
You can copy originals at a specied magnication.
1. Place the originals.
If you want to copy multiple originals, place all of the originals on the ADF.
“Placing Originals” on page 35
Copying
>
Available Copying Methods
>
Copying by Enlarging or Reducing
69
2. Select Copy on the home screen.
3. Select the Advanced Settings tab, select Reduce/Enlarge.
4. Specify the amount of enlargement or reduction, and then select OK.
5. Tap
x
on the Copy tab.
Copying Multiple Originals onto One Sheet
You can copy the multiple originals onto a single sheet.
1. Place all originals face up in the ADF.
“Placing Originals” on page 35
Place them in the direction shown in the illustration.
❏Portrait Originals
❏Landscape Originals
c
Important:
If you want to copy originals that are not supported by the ADF, use the scanner glass.
“Originals that are not Supported by the ADF” on page 36
Note:
You can also place the originals on the scanner glass.
“Placing Originals” on page 35
2. Select Copy on the home screen.
3. Select the Advanced Settings tab, and then select Multi-Page > 2-up.
Copying
>
Available Copying Methods
>
Copying Multiple Originals onto One Sheet
70
4. Specify the layout order and the original orientation, and then select OK.
5. Tap
x
on the Copy tab.
Copying Originals Using Good Quality
You can copy originals without shadows and punched holes.
1. Place the originals.
If you want to copy multiple originals, place all of the originals on the ADF.
“Placing Originals” on page 35
2. Select Copy on the home screen.
3. Select the Advanced Settings tab, select Remove Shadow or Remove Punch Holes, and then enable the
setting.
4. Tap
x
on the Copy tab.
Copying ID card
Scans both sides of an ID card and copies onto one side of a paper.
1. Place the original on the scanner glass.
“Placing Originals” on page 35
2. Select Copy on the home screen.
3. Select the Advanced Settings tab, and then enable ID Card Copy.
4. Tap
x
on the Copy tab.
Copying
>
Available Copying Methods
>
Copying ID card
71
Copying in Page Order
When making multiple copies of a multi-page document, you can discharge one copy at a time in page order.
1. Place the originals.
“Placing Originals” on page 35
2. Select Copy on the home screen.
3. Select the Advanced tab, and then select Finishing > Collate (Page Order).
4. Tap
x
on the Copy tab.
Basic Menu Options for Copying
Note:
e items may not be available depending on other settings you made.
B&W:
Copies the original in black and white (monochrome).
Color:
Copies the original in color.
(2-Sided):
Select 2-sided layout.
❏1→1-Sided
Copies one side of an original onto a single side of paper.
❏1→2-Sided
Copies two single-sided originals onto both sides of a single sheet of paper. Select the orientation
of your original and the binding position of the paper.
(Density):
Increase the level of density when the copying results are faint. Decrease the level of density when ink
smears.
Copying
>
Basic Menu Options for Copying
72
Advanced Menu Options for Copying
Note:
e items may not be available depending on other settings you made.
Paper Setting:
Select the paper size and the paper type you loaded.
Reduce/Enlarge:
Congures the magnication ratio of the enlargement or reduction. Tap the value and specify the
magnication used to enlarge or reduce the original within a range of 25 to 400%.
❏Actual Size
Copies at 100 % magnication.
❏A4→A5 and others
Automatically enlarges or reduces the original to t to a specic paper size.
❏Auto Fit Page
Detects the scan area and automatically enlarges or reduces the original to t to the paper size you
selected. When there are white margins around the original, the white margins from the corner
mark of the scanner glass are detected as the scan area, but the margins at the opposite side may be
cropped.
Original Size:
Select the size of your original. When copying non-standard size originals, select the size closest to
your original.
Multi-Page:
Select the copy layout.
❏Single Page
Copies a single-sided original onto a single sheet.
❏2-up
Copies two single-sided originals onto a single sheet in 2-up layout. Select the layout order and the
orientation of your original.
Copying
>
Advanced Menu Options for Copying
73
Quality:
Select the quality for copying. Selecting Best provides higher quality printing, but the printing speed
may be slower.
Finishing:
Select how to eject the paper for multiple copies of multiple originals.
❏Group (Same Pages)
Copies the originals by page as a group.
❏Collate (Page Order)
Copies the originals collated in order and sorted into sets.
Original Orientation:
Select the orientation of your original.
Remove Shadow:
Removes shadows that appear around copies when copying thick paper or that appear in the center of
copies when copying a booklet.
Remove Punch Holes:
Removes the binding holes when copying.
ID Card Copy:
Scans both sides of an ID card and copies onto one side of a paper.
Clear All Settings:
Resets the copy settings to their defaults.
Copying
>
Advanced Menu Options for Copying
74
Scanning
Basic Information on Scanning........................................76
Scanning Originals to a Computer......................................79
Scanning Originals to the Cloud....................................... 80
Scanning Using WSD............................................... 82
Scanning Originals to a Smart Device....................................84
Basic Information on Scanning
What is a "Scan"?
A "scan" is the process of converting the optical information of paper data such as documents into digital image
data.
You can save scanned data as a digital image such as a JPEG or PDF.
You can then print the image, send it by email, and so on.
Scanning Uses
You can use scanning in a variety of ways to make your life more convenient.
❏By scanning a paper document and turning it into digital data, you can read it on a computer or a smart device.
❏By scanning tickets or yers into digital data, you can dispose of the originals and reduce clutter.
❏By scanning important documents, you can back them up to cloud services or another storage medium, just in
case they get lost.
❏You can send the scanned photos or documents to friends by email.
❏By scanning hand-drawn illustrations and so on, you can share them on social media at a much higher quality
than by just taking a photo on your smart device.
❏By scanning your favorite pages from newspapers or magazines, you can save them and dispose of the originals.
Available Scanning Methods
You can use any of the following methods to scan using this printer.
Scanning to a Computer
ere are two methods of scanning originals to a computer; scanning using the printer’s control panel, and
scanning from the computer.
Scanning
>
Basic Information on Scanning
>
Available Scanning Methods
76
You can scan easily from the control panel.
Use the scanning application Epson ScanSmart to scan from the computer. You can edit images aer scanning.
Sending to a Cloud Service
You can send scanned images from the printer's control panel to cloud services that have been registered in
advance.
Scanning Using WSD
You can save the scanned image to a computer connected to the printer, using WSD feature.
If you are using the Windows 7/Windows Vista, you need to make WSD settings on your computer before
scanning.
Scanning
>
Basic Information on Scanning
>
Available Scanning Methods
77
Scanning Directly from Smart Devices
You can save scanned images directly to a smart device such as a smart phone or tablet by using the Epson Smart
Panel application on the smart device.
Recommended File Formats to Suit Your Purpose
Generally speaking, the JPEG format is suitable for photos while the PDF format is suitable for documents.
See the following descriptions to choose the best format for what you want to do.
File Format Description
JPEG (.jpg) A le format that allows you to compress the data to be saved. If the compression ratio
is high, the image quality declines, and you cannot convert the image back to the
original quality.
This is the standard image format for digital cameras. This format is suitable for images
that have many colors.
PDF (.pdf) A general le format that can be used across dierent operating systems and provides
the same level of screen display and print result.
Also, you can save the multiple pages as a one le.
You can view PDF les using dedicated PDF reading software or in Web browsers.
Recommended Resolutions to Suit Your Purpose
Resolution indicates the number of pixels (smallest area of an image) for each inch (25.4 mm), and is measured in
dpi (dots per inch). e advantage of increasing the resolution is that the details in the image become ne.
However, it can also have the following disadvantages.
❏e le size becomes large
(When you double the resolution, the le size becomes about four times larger.)
❏Scanning, saving, and reading the image takes a long time
❏Sending and receiving emails or faxes takes a long time
❏e image becomes too large to t the display or print on the paper
See the table and set the appropriate resolution for the purpose of your scanned image.
Scanning
>
Basic Information on Scanning
>
Recommended Resolutions to Suit Your Purpose
78
Purpose Resolution (Reference)
Displaying on a computer
Sending by email
Up to 200 dpi
Printing using a printer
Sending by fax
200 to 300 dpi
Scanning Originals to a Computer
ere are two methods of scanning originals to a computer; scanning using the printer’s control panel, and
scanning from the computer.
Scanning from the Control Panel
Note:
To use this feature, make sure the following applications are installed on your computer.
❏Epson ScanSmart (Windows 7 or later, or OS X El Capitan or later)
❏Epson Event Manager (Windows Vista/Windows XP, or OS X Yosemite/OS X Mavericks/OS X Mountain Lion/Mac OS
X v10.7.x/Mac OS X v10.6.8)
❏Epson Scan 2 (application required to use the scanner feature)
See the following to check for installed applications.
Windows 10: Click on the start button, and then select Windows System-Control Panel-Programs-Programs and
Features.
Windows 8.1/Windows 8: Select Desktop-Settings-Control Panel-Programs-Programs and Features.
Windows 7/Windowes Vista: Click the start button, and then select Control Panel-Programs-Programs and Features.
Windows XP: Click the start button, and then select Control Panel-Add or Remove Programs.
Mac OS: Select Go > Applications > Epson Soware.
1. Place the originals.
“Placing Originals” on page 35
2. Select Scan > Computer on the control panel.
3. Select a computer on which to save the scanned images.
❏If the Select Computer screen is displayed, select the computer from the screen.
❏If the Scan to Computer screen is displayed and the computer is already selected, make sure the selected
computer is correct. If you want to change the computer, select , and then select another computer.
4. Select to select how to save the scanned image to a computer.
❏Preview on Computer (Windows 7 or later, or OS X El Capitan or later): Previews the scanned image on a
computer before saving images.
❏Save as JPEG: Saves the scanned image in JPEG format.
Scanning
>
Scanning Originals to a Computer
>
Scanning from the Control Panel
79
❏Save as PDF: Saves the scanned image in PDF format.
5. Tap
x
.
When using Windows 7 or later, or OS X El Capitan or later: Epson ScanSmart automatically starts on your
computer, and scanning starts.
Note:
❏See the Epson ScanSmart help for detailed operation information for the soware. Click Help on the Epson
ScanSmart screen to open the help.
❏You can not only start scanning from the printer but also from your computer by using Epson ScanSmart.
Scanning from a Computer
You can scan from a computer by using Epson ScanSmart.
is application allows you to scan documents easily, and then save the scanned images in simple steps.
1. Place the originals.
“Placing Originals” on page 35
2. Start Epson ScanSmart.
❏Windows 10
Click the start button, and then select Epson Soware > Epson ScanSmart.
❏Windows 8.1/Windows 8
Enter the application name in the search charm, and then select the displayed icon.
❏Windows 7
Click the start button, and then select All Programs > Epson Soware > Epson ScanSmart.
❏Mac OS
Select Go > Applications > Epson Soware > Epson ScanSmart.
3. When the Epson ScanSmart screen is displayed, follow the on-screen instructions to scan.
Note:
Click Help to view detailed operation information.
Scanning Originals to the Cloud
Before using this feature, make settings using Epson Connect. See the following Epson Connect portal website for
details.
https://www.epsonconnect.com/
http://www.epsonconnect.eu (Europe only)
1. Place the originals.
“Placing Originals” on page 35
2. Select Scan > Cloud on the control panel.
Scanning
>
Scanning Originals to the Cloud
80
3. Select on the top of the screen, and then select a destination.
4. Make the scan settings.
“Basic Menu Options for Scanning to the Cloud” on page 81
“Advanced Menu Options for Scanning to the Cloud” on page 81
5. Tap
x
.
Basic Menu Options for Scanning to the Cloud
Note:
e items may not be available depending on other settings you made.
B&W/Color
Select whether to scan in monochrome or in color.
JPEG/PDF
Select the format in which to save the scanned image.
Advanced Menu Options for Scanning to the Cloud
Note:
e items may not be available depending on other settings you made.
Scan Area:
Select the scan area. To crop the white space around the text or image when scanning, select Auto
Cropping. To scan at the maximum area of the scanner glass, select Max Area.
❏Original Orientation:
Select the orientation of the original.
Original Type:
Select the type of your original.
Density:
Select the contrast of the scanned image.
Remove Shadow:
Remove the shadows of the original that appear in the scanned image.
❏Surround:
Remove the shadows at the edge of the original.
❏Center:
Remove the shadows of the binding margin of the booklet.
Scanning
>
Scanning Originals to the Cloud
>
Advanced Menu Options for Scanning to the Cloud
81
Remove Punch Holes:
Remove the punch holes that appear in the scanned image. You can specify the area to erase the
punch holes by entering a value in the box on the right.
❏Erasing Position:
Select the position to remove the punch holes.
❏Original Orientation:
Select the orientation of the original.
Clear All Settings
Resets the scan settings to their defaults.
Scanning Using WSD
Note:
❏is feature is only available for computers running Windows 10/Windows 8.1/Windows 8/Windows 7/Windows Vista.
❏If you are using Windows 7/Windows Vista, you need to setup your computer in advance using this feature.
“Setting Up a WSD Port” on page 82
1. Place the originals.
“Placing Originals” on page 35
2. Select Scan > WSD on the control panel.
3. Select a computer.
4. Tap
x
.
Setting Up a WSD Port
is section explains how to set up a WSD port for Windows 7/Windows Vista.
Note:
For Windows 10/Windows 8.1/Windows 8, the WSD port is set up automatically.
e following is necessary to set up a WSD port.
❏e printer and the computer are connected to the network.
❏e printer driver is installed on the computer.
1. Turn the printer on.
2. Click start, and then click Network on the computer.
3. Right-click the printer, and then click Install.
Click Continue when the User Account Control screen is displayed.
Scanning
>
Scanning Using WSD
>
Setting Up a WSD Port
82
Click Uninstall and start again if the Uninstall screen is displayed.
Note:
e printer name you set on the network and model name (EPSON XXXXXX (XX-XXXX)) are displayed on the
network screen. You can check the printer's name set on the network from the printer's control panel or by printing a
network status sheet.
4. Click Your device is ready to use.
5. Check the message, and then click Close.
6. Open the Devices and Printers screen.
❏Windows 7
Click start > Control Panel > Hardware and Sound (or Hardware) > Devices and Printers.
Scanning
>
Scanning Using WSD
>
Setting Up a WSD Port
83
❏Windows Vista
Click start > Control Panel > Hardware and Sound > Printers.
7. Check that an icon with the printer's name on the network is displayed.
Select the printer name when using with WSD.
Scanning Originals to a Smart Device
Note:
❏Before scanning, install Epson Smart Panel on your smart device.
❏Epson Smart Panel screens are subject to change without notice.
❏Epson Smart Panel contents may vary depending on the product.
1. Place the originals.
“Placing Originals” on page 35
2. Start Epson Smart Panel on your smart device.
3. Select scan menu on the home screen.
4. Follow the on-screen instructions to scan and save the images.
Scanning
>
Scanning Originals to a Smart Device
84
Faxing
Before Using Fax Features............................................86
Overview of this Printer's Fax Features...................................86
Sending Faxes Using the Printer........................................89
Receiving Faxes on the Printer.........................................92
Menu Options for Faxing.............................................96
Menu Options for Inbox.............................................99
Using Other Faxing Features.........................................100
Sending a Fax from a Computer.......................................100
Receiving Faxes on a Computer.......................................104
Before Using Fax Features
Faxing feature is available only for ET-5170 Series/L6490 Series.
Check the following before you start using the fax features.
❏e printer and the phone line, and (if it is being used) the phone machine are connected correctly
❏Fax basic settings (Fax Setting Wizard) is complete
❏Other necessary Fax Settings are complete
See "Related Information" below to make settings.
Related Information
&“Connecting the Printer to a Phone Line” on page 283
&“Making the Printer Ready to Send and Receive Faxes” on page 286
&“Making Settings for the Printer's Fax Features According to Use” on page 288
&“Basic Settings” on page 260
&“Making Contacts Available” on page 280
&“User Settings” on page 264
Overview of this Printer's Fax Features
Feature: Sending Faxes
Sending Methods
❏Sending automatically
When you scan an original by tapping
x
(Send), the printer dials the recipients and sends the fax.
“Sending Faxes Using the Printer” on page 89
❏Sending manually
When you perform a manual check on the line connection by dialing the recipient, tap
x
(Send) to start
sending a fax directly.
“Sending Faxes Dialing from the External Phone Device” on page 91
Recipient Designation when Sending a Fax
You can enter recipients using Keypad, Contacts, and Recent.
“Recipient” on page 96
“Making Contacts Available” on page 280
Scan Settings when Sending a Fax
You c a n s ele ct it e ms such as Resolution or Original Size (Glass) when sending faxes.
“Scan Settings:” on page 96
Faxing
>
Overview of this Printer's Fax Features
>
Feature: Sending Faxes
86
Using Fax Send Settings when Sending a Fax
You can use Fax Send Settings such as Direct Send (to send a large document stably) or Send Fax Later (to send a
fax at a time you specied).
“Fax Send Settings:” on page 97
Feature: Receiving Faxes
Receive Mode
ere are two options in Receive Mode for receiving incoming faxes.
❏Manual
Mainly for phoning, but also for faxing
“Usage of Manual Mode” on page 93
❏Auto
- Only for faxing (external phone device is not required)
- Mainly for faxing, and sometimes phoning
“Usage of Auto Mode” on page 93
Receiving Faxes by Operating a Connected Phone
You can receive faxes by only operating an external phone device.
“Basic Settings” on page 260
“Making Settings When You Connect a Phone Device” on page 289
Destinations of Received Faxes
❏Received faxes are printed by default. You can set up destinations for received faxes to the inbox. If you save in
the inbox, you can check the contents on the screen.
“Fax Output Settings” on page 257
“Menu Options for Inbox” on page 99
“Viewing Received Faxes Saved in the Printer on the LCD Screen” on page 95
Feature: PC-FAX Send/Receive (Windows/Mac OS)
PC-FAX Send
You can send faxes from a computer.
“Soware for Faxing” on page 247
Faxing
>
Overview of this Printer's Fax Features
>
Feature: PC-FAX Send/Receive (Windows/Mac OS)
87
“Sending a Fax from a Computer” on page 100
PC-FAX Receive
You can receive faxes on a computer.
“Making Settings to Send and Receive Faxes on a Computer” on page 291
“Soware for Faxing” on page 247
“Receiving Faxes on a Computer” on page 104
Features: Various Fax Reports
You can check the status of sent and received faxes in a report.
“Report Settings” on page 259
“Fax Send Settings:” on page 97
“Transmission Log:” on page 98
“Fax Report:” on page 98
Feature: Security when Sending and Receiving Faxes
You can use many security features such as Direct Dialing Restrictions to prevent sending to the wrong
destination, or Backup Data Auto Clear to prevent information leakage. You can set a password for the inbox in
the printer.
“Security Settings” on page 262
“Save to Inbox:” on page 257
Features: Other Useful Features
Blocking Junk Faxes
You can reject junk faxes.
“Rejection Fax:” on page 261
Receiving Faxes After Dialing
Aer dialing to another fax machine, you can receive documents from that fax machine.
“Receiving Faxes by Making a Phone Call” on page 94
Faxing
>
Overview of this Printer's Fax Features
>
Features: Other Useful Features
88
“Polling Receive:” on page 98
Sending Faxes Using the Printer
You can send faxes by entering fax numbers for recipients on the printer's control panel.
Note:
When sending a fax in monochrome, you can preview the scanned image on the LCD screen before sending.
1. Place the originals.
You can send up to 100 pages in one transmission; however depending on the remaining amount of memory,
you may not be able to send faxes even with less than 100 pages.
“Placing Originals” on page 35
2. Select Fax on the printer's control panel.
3. Specify the recipient.
“Selecting Recipients” on page 89
4. Select the Fax Settings tab, and then make settings as necessary.
“Fax Settings” on page 96
5. Tap
x
to send the fax .
Note:
❏If the fax number is busy or there are some problems, the printer automatically redials aer one minute.
❏To cancel sending, tap
y
.
❏It takes longer to send a fax in color because the printer performs scanning and sending simultaneously. While the
printer is sending a fax in color, you cannot use the other features.
Selecting Recipients
You can specify recipients on the Recipient tab to send the fax using the following methods.
Entering Fax Number Manually
Select Keypad, enter a fax number on the screen displayed, and then select OK.
- To add a pause (pause for three seconds during dialing), enter a hyphen (-).
- If you have set an external access code in Line Type, enter "#" (hash) instead of the actual external access code at
the beginning of the fax number.
Note:
If you cannot manually enter a fax number, Direct Dialing Restrictions in Security Settings is set to On. Select fax
recipients from the contacts list or the sent fax history.
Selecting the recipients from the contacts list
Select Contacts and select recipients you want to send. If the recipient you want to send to has not been registered
in Contacts yet, select Add Entry and register it.
Faxing
>
Sending Faxes Using the Printer
>
Selecting Recipients
89
Selecting the recipients from the sent fax history
Select Recent, and then select a recipient.
Note:
To delete recipients you entered, display the list of recipients by tapping on the eld of a fax number or the number of
recipients on the LCD screen, select the recipient from the list, and then select Remove.
Related Information
&“Making Contacts Available” on page 280
Various Ways of Sending Faxes
Sending a Fax after Checking the Scanned Image
You can preview the scanned image on the LCD screen before sending the fax. (Monochrome faxes only)
1. Place the originals.
“Placing Originals” on page 35
2. Select Fax on the home screen.
3. Specify the recipient.
“Selecting Recipients” on page 89
4. Select the Fax Settings tab, and then make settings as necessary.
“Fax Settings” on page 96
5. Select Preview on the fax top screen to scan, check the scanned document image.
- : Moves the screen in the direction of the arrows.
- : Reduces or enlarges.
- : Moves to the previous or the next page.
Note:
❏When Direct Send is enabled, you cannot preview.
❏If you leave the printer untouched for 20 seconds aer prompted to set the next originals, the printer stops storing
and starts sending the document.
❏e image quality of a sent fax may be dierent from what you previewed depending on the capability of the
recipient machine.
6. Select Start Sending. Otherwise, select Cancel
Note:
e image quality of a sent fax may be dierent from what you previewed depending on the capability of the recipient
machine.
Faxing
>
Sending Faxes Using the Printer
>
Various Ways of Sending Faxes
90
Sending Faxes Dialing from the External Phone Device
You can send a fax by dialing using the connected telephone when you want to talk over the phone before sending
a fax, or when the recipient's fax machine does not switch to the fax automatically.
1. Pick up the handset of the connected telephone, and then dial the recipient's fax number using the phone.
Note:
When the recipient answers the phone, you can talk with the recipient.
2. Select Fax on the home screen.
3. Make necessary settings on theFax Settings.
“Fax Settings” on page 96
4. When you hear a fax tone, tap
x
, and then hang up the handset.
Note:
When a number is dialed using the connected telephone, it takes longer to send a fax because the printer performs
scanning and sending simultaneously. While sending the fax, you cannot use the other features.
Sending Many Pages of a Monochrome Document (Direct Send)
When sending a fax in monochrome, the scanned document is temporarily stored in the printer's memory.
erefore, sending a lot of pages may cause the printer to run out of memory and stop sending the fax. You can
avoid this by enabling the Direct Send feature, however, it takes longer to send the fax because the printer
performs scanning and sending simultaneously. You can use this feature when there is only one recipient.
Accessing the Menu
You c a n nd the menu on the printer's control panel below.
Fax > Fax Settings > Direct Send.
Sending Faxes in Monochrome at Specied Time of the Day (Send Fax Later)
You can set to send a fax at a specied time. Only monochrome faxes can be sent when the time to send is
specied.
1. Select Fax on the home screen.
2. Specify the recipient.
“Selecting Recipients” on page 89
3. Select the Fax Settings tab, and then select Send Fax Later.
4. Tap the Send Fax Later eld to set this to On.
5. Select the Time eld, enter the time you want to send the fax, and then select OK.
Faxing
>
Sending Faxes Using the Printer
>
Various Ways of Sending Faxes
91
6. Select OK to apply the settings.
You can also make settings such as the resolution and the sending method as necessary.
7. Send the fax.
Note:
You cannot send another fax until the fax has been sent at the specied time. If you want to send another one, you need
to cancel the scheduled fax by selecting Fax on the home screen, and then deleting it.
Sending Dierent Size Documents Using ADF (ADF Continuous Scan)
Sending faxes by placing originals one by one, or by placing originals by size, you can send them as one document
at their original sizes.
If you place dierent sized originals in the ADF, all of the originals are sent at the largest size among them. To send
originals at their original sizes, do not place originals with mixed sizes.
1. Place the rst batch of originals at the same size.
2. Select Fax on the home screen.
3. Specify the recipient.
“Selecting Recipients” on page 89
4. Select the Fax Settings tab, and then tap ADF Continuous Scan to set this to On.
You can also make settings such as the resolution and the sending method as necessary.
5. Tap
x
(Send) on the Recipienttab.
6. When scanning the rst set of originals is complete and a message is displayed on the control panel asking you
to scan the next set of originals, select Yes, set the next originals, and then select Start Scanning.
Note:
If you leave the printer untouched for 20 seconds aer prompted to set the next originals, the printer stops storing and
starts sending the document.
Receiving Faxes on the Printer
If the printer is connected to the phone line and basic settings have been completed using the Fax Setting Wizard,
you can receive faxes.
You can save received faxes, check them on the printer screen, and print them as necessary.
Received faxes are printed in the printer's initial settings.
Faxing
>
Receiving Faxes on the Printer
92
When you want to check the status of the fax settings, print a Fax Settings List by selecting Fax > (More) > Fax
Report > Fax Settings List.
Receiving Incoming Faxes
ere are two options in Receive Mode.
Related Information
&“Usage of Manual Mode” on page 93
&“Usage of Auto Mode” on page 93
Usage of Manual Mode
is mode is mainly for making phone calls, but is also for faxing.
Receiving Faxes
When the telephone rings, you can answer the ringing manually by picking up the handset.
❏When you hear a fax signal (baud):
Select Fax on the printer's home screen, select Send/Receive > Receive, and then tap
x
. Next, hang up the
handset.
❏If the ringing is for a voice call:
You can answer the phone as normal.
Receiving Faxes Using only the Connected Telephone
When Remote Receive is set, you can receive faxes by simply entering the Start Code.
When the telephone rings, pick up the handset. When you hear a fax tone (baud), dial the two digit Start Code,
and then hang up the handset.
Related Information
&“Remote Receive:” on page 261
Usage of Auto Mode
is mode allows you to use the line for the following uses.
❏Using the line for faxing only (external telephone is not necessary)
❏Using the line for faxing mainly, and sometimes phoning
Receiving Faxes Without an External Phone Device
e printer automatically switches to receive faxes when the number of rings you set in Rings to Answer is
complete.
Faxing
>
Receiving Faxes on the Printer
>
Receiving Incoming Faxes
93
Receiving Faxes With an External Phone Device
A printer with an external phone device works as follows.
❏When the answering machine answers within the number of rings set in Rings to Answer:
- If the ringing is for a fax: e printer automatically switches to receive faxes.
- If the ringing is for a voice call: e answering machine can receive voice calls and record voice messages.
❏When you pick up the handset within the number of rings set in Rings to Answer:
- If the ringing is for a fax: Hold the line until the printer automatically starts receiving the fax by displaying
Connecting on the printer's control panel. Once the printer starts receiving the fax, you can hang up the
handset. To start receiving the fax immediately, use the same steps as for Manual. Select Fax on the printer's
control panel, and then select Send/Receive > Receive. Next, tap
x
, and then hang up the handset.
- If the ringing is for a voice call: You can answer the phone as normal.
❏When the ringing stops and the printer automatically switches to receive faxes:
- If the ringing is for a fax: e printer starts receiving faxes.
- If the ringing is for a voice call: You cannot answer the phone. Ask the person to call you back.
Note:
Set the number of rings to answer for the answering machine to a lower number than the number set in Rings to Answer.
Otherwise, the answering machine cannot receive voice calls to record voice messages. For details on setting up the answering
machine, see the manual supplied with the answering machine.
Receiving Faxes by Making a Phone Call
You can receive a fax stored on another fax machine by dialing the fax number.
Receiving Faxes by Polling (Polling Receive)
You can receive a fax stored on another fax machine by dialing the fax number. Use this feature to receive a
document from a fax information service. However, if the fax information service has an audio guidance feature
that you need to follow to receive a document, you cannot use this feature.
Note:
To receive a document from a fax information service that uses audio guidance, just dial the fax number using the connected
telephone, and operate the phone and the printer following the audio guidance.
1. Select Fax on the home screen.
2. Tap (More).
3. Tap Polling Receive to set this to On, and then tap Close.
4. Enter the fax number.
Note:
When Security Settings > Direct Dialing Restrictions is set to On, you can only select fax recipients from the contact
list or the sent fax history. You cannot manually enter a fax number.
5. Tap
x
.
Faxing
>
Receiving Faxes on the Printer
>
Receiving Faxes by Making a Phone Call
94
Viewing Received Faxes Saved in the Printer on the LCD Screen
If you set up to save received faxes in the printer, you can view the contents and print as necessary.
“Making Settings to Save Received Faxes” on page 289
1. Tap on the home screen.
Note:
When there are received faxes that have not been read, the number of unread documents is displayed on the on the
home screen.
2. Tap Open Inbox (XX Unread).
3. If the inbox has been password protected, enter the inbox password.
4. Select the fax you want to view from the list.
e contents of the fax are displayed.
❏: Moves the screen in the direction of the arrows.
❏: Reduces or enlarges.
❏: Rotates the image to the right by 90 degrees.
❏: Moves to the previous or the next page.
❏To hide the operation icons, tap anywhere on the preview screen except for the icons. Tap again to display
the icons.
5. Select whether to print or delete the document you have viewed, and then follow the on-screen instructions.
c
Important:
If the printer runs out of memory, receiving and sending faxes is disabled. Delete documents that you have
already read or printed.
Faxing
>
Receiving Faxes on the Printer
>
Viewing Received Faxes Saved in the Printer on the LCD Screen
95
Menu Options for Faxing
Recipient
Select the menus on the control panel as described below.
Fax > Recipient
Keypad:
Manually enter a fax number.
Contacts:
Select a recipient from the contacts list. You can also add or edit a contact.
Recent:
Select a recipient from the sent fax history. You can also add the recipient to the contacts list.
Related Information
&“Selecting Recipients” on page 89
Fax Settings
Select the menus on the control panel as described below.
Fax > Fax Settings
Scan Settings:
Original Size (Glass):
Select the size and orientation of the original you placed on the scanner glass.
Color Mode:
Select whether to scan in color or in monochrome.
Resolution:
Select the resolution of the outgoing fax. If you select a higher resolution, the data size
becomes larger and it takes time to send the fax.
Density:
Sets the density of the outgoing fax. + makes the density darker, and - makes it lighter.
Remove Background:
Detects the paper color (background color) of the original document, and removes or lightens
the color. Depending on the darkness and vividness of the color, it may not be removed or
lightened
Faxing
>
Menu Options for Faxing
>
Fax Settings
96
Sharpness:
Enhances or defocuses the outline of the image. + enhances the sharpness, and - defocuses the
sharpness.
ADF Continuous Scan:
Sending faxes by placing originals one by one, or by placing originals by size, you can send
them as one document at their original sizes. See the related information below on this topic.
Fax Send Settings:
Direct Send:
Sends a monochrome fax while scanning the originals. Since scanned originals are not stored
temporarily in the printer's memory even when sending a large volume of pages, you can avoid
printer errors due to a lack of memory. Note that sending using this feature takes longer than
not using this feature. See the related information below on this topic.
You cannot use this feature when sending a fax to multiple recipients.
Send Fax Later:
Sends a fax at a time you specied. Only a monochrome fax is available when using this
option. See the related information below on this topic.
Add Sender Information:
❏Add Sender Information
Select the position where you want to include the header information (sender name and fax
number) in the outgoing fax, or not to include the information.
- O: Sends a fax with no header information.
- Outside of Image: Sends a fax with header information in the top white margin of the fax.
is keeps the header from overlapping with the scanned image, however, the fax received
by the recipient may be printed across two sheets depending on the size of the originals.
- Inside of Image: Sends a fax with header information approximately 7 mm lower than the
top of the scanned image. e header may overlap with the image, however, the fax received
by the recipient will not be split into two documents.
❏Fax Header
Select the header for the recipient. To use this feature, you should register multiple headers
in advance.
❏Additional Information
Select the information you want to add. You can select one from You r Ph one Nu mb er and
Destination List.
Transmission Report:
Prints a transmission report aer you send the fax.
Print on Error prints a report only when an error occurs.
When Attach Fax image to report has been set in Settings > General Settings > Fax Settings
> Report Settings, faxes with errors are also printed with the report.
Clear All Settings:
Restores all settings in Scan Settings and Fax Send Settings to their defaults.
Faxing
>
Menu Options for Faxing
>
Fax Settings
97
Related Information
&“Sending Dierent Size Documents Using ADF (ADF Continuous Scan)” on page 92
&“Sending Many Pages of a Monochrome Document (Direct Send)” on page 91
&“Sending Faxes in Monochrome at Specied Time of the Day (Send Fax Later)” on page 91
More
Selecting in Fax on the home screen displays the More menu.
Transmission Log:
You can check the history of sent or received fax jobs.
Fax Report:
Last Transmission:
Prints a report for the previous fax that was sent or received through polling.
Fax Log:
Prints a transmission report. You can set to print this report automatically using the following
menu.
Settings > General Settings > Fax Settings > Report Settings > Fax Log Auto Print
Fax Settings List:
Prints the current fax settings.
Protocol Trace:
Prints a detailed report for the previous fax that was sent or received.
Polling Receive:
When this is set to On and you call the sender's fax number, you can receive documents from the
sender's fax machine. See the related information below for details on how to receive faxes using
Polling Receive.
When you leave the Fax menu, the setting returns to O (default).
Inbox:
Accesses (Inbox) on the home screen.
Reprint Faxes:
Reprints the received faxes in the printer.
Fax Settings:
Accesses Settings > General Settings > Fax Settings. Access the setting menu as an administrator.
Related Information
&“Receiving Faxes by Polling (Polling Receive)” on page 94
Faxing
>
Menu Options for Faxing
>
More
98
Menu Options for Inbox
:
You can access the Inbox where the received faxes are stored by tapping this icon. When there are received
faxes that have not been read, the number of unread documents is displayed on the .
Open Inbox (XX Unread)
(Inbox Menu)
Print All:
Selecting this prints out all received faxes in the inbox.
Delete All:
Selecting this deletes all received faxes in the inbox.
Inbox (List)
You can save up to 100 documents in the inbox in total.
preview screen
❏: Reduces or enlarges.
❏: Rotates the image to the right by 90 degrees.
❏: Moves the screen in the direction of the arrows.
❏: Moves to the previous or the next page.
To hide the operation icons, tap anywhere on the preview screen except for the icons.
Tap again to display the icons.
Delete:
Deletes the document you are previewing.
Proceed to Print:
Prints the document you are previewing. You can make settings such as 2-Sided before
starting printing.
(Preview menu)
Details:
Displays information for the selected document such as the saved date and time,
and total number of pages.
Related Information
&“Making Settings to Save Received Faxes” on page 289
Faxing
>
Menu Options for Inbox
99
Using Other Faxing Features
Printing Fax Report Manually
1. Select Fax on the home screen.
2. Tap (More).
3. Select Fax Report.
4. Select the report you want to print, and then follow the on-screen instructions.
Note:
You can change the report format. From the home screen, select Settings > General Settings > Fax Settings > Report
Settings, and then change the Attach Fax image to report or Report Format settings.
Sending a Fax from a Computer
You can send faxes from the computer by using the FAX Utility and PC-FAX driver.
Note:
❏Check if the FAX Utility and the printer's PC-FAX driver has been installed before using this feature.
“Application for Conguring Fax Operations and Sending Faxes (FAX Utility)” on page 247
“Application for Sending Faxes (PC-FAX Driver)” on page 248
❏If the FAX Utility is not installed, install the FAX Utility using the EPSON Soware Updater (application for updating
soware).
Sending Documents Created Using an Application (Windows)
By selecting a printer fax from the Print menu of an application like Microso Word or Excel, you can directly
transmit data such as documents, drawings, and tables you have created, with a cover sheet.
Note:
e following explanation uses Microso Word as an example. e actual operation may dier depending on the application
you use. For details, see the application’s help.
1. Using an application, create a document to transmit by fax.
2. Click Print from the File menu.
e application’s Print window appears.
3. Select XXXXX (FAX) (where XXXXX is your printer name) in Printer, and then check the settings for fax
sending.
❏Specify 1 in Number of copies. Fax may not be transmitted correctly if you specify 2 or more.
❏You can send up to 100 pages in one fax transmission.
Faxing
>
Sending a Fax from a Computer
>
Sending Documents Created Using an Application (Windows)
100
4. Click Printer Properties or Properties if you want to specify Paper Size, Orientation, Color, Image Quality,
or Character Density.
For details, see the PC-FAX driver help.
5. Click Print.
Note:
When Using FAX Utility for the rst time, a window for registering your information is displayed. Enter the necessary
information, and then click OK.
Recipient Settings screen of FAX Utility is displayed.
6. When you want to send other documents in the same fax transmission, select Add documents to send
checkbox.
e screen for adding documents is displayed when you click Next in step 9.
7. Select Attach a cover sheet checkbox if necessary.
8. Specify a recipient.
❏Selecting a recipient (name, fax number and so on) from PC-FAX Phone Book:
If the recipient is saved in the phone book, do the steps below.
A
Click the PC-FAX Phone Book tab.
B
Select the recipient from the list and click Add.
❏Selecting a recipient (name, fax number and so on) from the contacts on the printer:
If the recipient is saved in the contacts on the printer, do the steps below.
A
Click the Contacts on Printer tab.
B
Select contacts from the list and click Add to proceed to Add to Recipient window.
C
Select the contacts from the list displayed, and then click Edit.
D
Add the personal data such as Company/Corp. and Title as necessary, and then click OK to return to
the Add to Recipient window.
E
As necessary, select the checkbox of Register in the PC-FAX Phone Book to save the contacts to PC-
FAX Phone Book.
F
Click OK.
❏Specifying a recipient (name, fax number and so on) directly:
Do the steps below.
A
Click the Manual Dial tab.
B
Enter the necessary information.
C
Click Add.
Furthermore, by clicking Save to Phone Book, you can save the recipient in the list under the PC-FAX
Phone Book tab.
Note:
❏If your printer's Line Type is set to PBX and the access code has been set to use # (hash) instead of entering the exact
prex code, enter # (hash). For details, see Line Type in Basic Settings from related information link below.
❏If you have selected Enter fax number twice in the Optional Settings on the FAX Utility main screen, you need to
enter the same number again when you click Add or Next.
e recipient is added to the Recipient List displayed in the upper part of the window.
Faxing
>
Sending a Fax from a Computer
>
Sending Documents Created Using an Application (Windows)
101
9. Click Next.
❏When you have selected Add documents to send checkbox, follow the steps below to add documents in the
Document Merging window.
A
Open a document you want to add, and then select the same printer (fax name) in the Print window.
e document is added to the Document List to Merge list.
B
Click Preview to check the merged document.
C
Click Next.
Note:
e Image Quality and Color settings you have selected for the rst document are applied to other documents.
❏When you have selected Attach a cover sheet checkbox, specify the content of the cover sheet in the Cover
Sheet Settings window.
A
Select a cover sheet from samples in the Cover Sheet list. Note that there is no function to create an
original cover sheet or to add an original cover sheet to the list.
B
Enter the Subject and Message.
C
Click Next.
Note:
Set the following as necessary in Cover Sheet Settings.
❏Click Cover Sheet Formatting if you want to change the order of the items on the cover sheet. You can select the
cover sheet size in Paper Size. You can also select a cover sheet at a dierent size to the document being transmitted.
❏Click Font if you want to change the font used for the text on the cover sheet.
❏Click Sender Settings if you want to change the sender information.
❏Click Detailed Preview if you want to check the cover sheet with the subject and the message you entered.
10. Check the transmission content and click Send.
Make sure the name and fax number of the recipient are correct before transmitting. Click Preview to preview
the cover sheet and document to transmit.
Once transmission starts, a window displaying the transmission status appears.
Note:
❏To stop transmitting, select the data, and click Cancel . You can also cancel using the printer's control panel.
❏If an error occurs during transmission, the Communication error window appears. Check the error information
and retransmit.
❏e Fax Status Monitor screen (the screen mentioned above where you can check the transmission status) is not
displayed if Display Fax Status Monitor During Transmission is not selected in the Optional Settings screen of the
FAX Utility main screen.
Related Information
&“Basic Settings” on page 260
Sending Documents Created Using an Application (Mac OS)
By selecting a fax-capable printer from the Print menu of a commercially available application, you can send data
such as documents, drawings, and tables, you have created.
Faxing
>
Sending a Fax from a Computer
>
Sending Documents Created Using an Application (Mac OS)
102
Note:
e following explanation uses Text Edit, a standard Mac OS application as an example.
1. Create the document you want to send by fax in an application.
2. Click Print from the File menu.
e application’s Print window is displayed.
3. Select your printer (fax name) in Name, click
d
to display the detailed settings, check the print settings, and
then click OK.
4. Make settings for each item.
❏Specify 1 in Number of copies. Even if you specify 2 or more, only 1 copy is sent.
❏You can send up to 100 pages in one fax transmission.
Note:
e page size of documents you can send is the same as the paper size you can fax from the printer.
5. Select Fax Settings from the popup menu, and then make settings for each item.
See the PC-FAX driver's help for explanations on each setting item.
Click at the bottom le of the window to open the PC-FAX driver's help.
6. Select the Recipient Settings menu, and then specify the recipient.
❏Specifying a recipient (name, fax number, and so on) directly:
Click the Add item, enter the necessary information, and then click . e recipient is added to the
Recipient List displayed in the upper part of the window.
If you have selected "Enter fax number twice" in the PC-FAX driver settings, you need to enter the same
number again when you click .
If your fax connection line requires a prex code, enter External Access Prex.
Note:
If your printer's Line Type is set to PBX and the access code has been set to use # (hash) instead of entering the exact
prex code, enter # (hash). For details, see Line Type in Basic Settings from Related Information link below.
❏Selecting a recipient (name, fax number, and so on) from the phone book:
If the recipient is saved in the phone book, click . Select the recipient from the list, and then click Add
> OK.
If your fax connection line requires a prex code, enter External Access Prex.
Note:
If your printer's Line Type is set to PBX and the access code has been set to use # (hash) instead of entering the exact
prex code, enter # (hash). For details, see Line Type in Basic Settings from Related Information link below.
7. Check the recipient settings, and then click Fax.
Sending starts.
Make sure the name and fax number of the recipient are correct before transmitting.
Faxing
>
Sending a Fax from a Computer
>
Sending Documents Created Using an Application (Mac OS)
103
Note:
❏If you click the printer icon in Dock, the transmission status check screen is displayed. To stop sending, click the data,
and then click Delete.
❏If an error occurs during transmission, the Sending failed message is displayed. Check the transmission records on
the Fax Transmission Record screen.
❏Mixed paper size documents may not be sent correctly.
Related Information
&“Basic Settings” on page 260
Receiving Faxes on a Computer
Faxes can be received by a printer and saved in PDF format on a computer connected to the printer. Use the FAX
Utility (application) to make settings.
For details on how to operate FAX Utility, see Basic Operations in the FAX Utility help (displayed on the main
window). If the password entry screen is displayed on the computer screen while you are making settings, enter the
password. If you do not know the password, contact your administrator.
Note:
❏Check if the FAX Utility and the printer's PC-FAX driver have been installed and the FAX Utility settings have been
made before using this feature.
“Application for Conguring Fax Operations and Sending Faxes (FAX Utility)” on page 247
“Application for Sending Faxes (PC-FAX Driver)” on page 248
❏If the FAX Utility is not installed, install the FAX Utility using the EPSON Soware Updater (application for updating
soware).
c
Important:
❏To receive faxes on a computer, the Receive Mode on the printer's control panel must be set to Auto. Contact
your administrator for information on the printer settings status. To make settings on the printer's control panel,
select Settings > General Settings > Fax Settings > Basic Settings > Receive Mode.
❏e computer set to receive faxes should always be on. Received documents are saved in the printer's memory
temporarily before the documents are saved on the computer. If you turn o the computer, the printer's memory
might become full as it cannot send the documents to the computer.
❏e number of documents that have been temporarily saved to the printer’s memory are displayed on the on
the home screen.
❏To read the received faxes, you need to install a PDF viewer such as Adobe Reader in the computer.
Related Information
&“Making Settings to Send and Receive Faxes on a Computer” on page 291
Checking for New Faxes (Windows)
By setting up a computer to save faxes received by the printer, you can check the processing status of received faxes,
and whether or not there are any new faxes using the fax icon on the Windows task bar. By setting up the computer
Faxing
>
Receiving Faxes on a Computer
>
Checking for New Faxes (Windows)
104
to display a notication when new faxes are received, a notication screen pops up near the Windows system tray,
and you can check the new faxes.
Note:
❏Received fax data saved to the computer is removed from the printer's memory.
❏You need Adobe Reader to view the received faxes saved as PDF les.
Using the Fax Icon on the Task Bar (Windows)
You can check for new faxes and the operation status by using the fax icon displayed on the Windows taskbar.
1. Check the icon.
❏: Standing by.
❏: Checking for new faxes.
❏: Importing new faxes is complete.
2. Right-click the icon, and then click View Receiving Fax Record.
e Receiving Fax Record screen is displayed.
3. Check the date and the sender in the list, and then open the received le as a PDF.
Note:
❏Received faxes are automatically renamed using the following naming format.
YYYYMMDDHHMMSS_xxxxxxxxxx_nnnnn (Year/Month/Day/Hour/Minute/Second_sender’s number)
❏You can also open the received fax folder directly when you right-click the icon. For details, see Optional Settings in
the FAX Utility and its help (displayed on the main window).
While the fax icon indicates that it is standing by, you can check for new faxes instantly by selecting Check new
faxes now.
Using the Notication Window (Windows)
When you set to notify you the new faxes exist, a notication window is displayed near the task bar for each the
fax.
1. Check the notication screen displayed on your computer screen.
Note:
e notication screen disappears if no operation is performed for a given length of time. You can change the
notication settings such as the display time.
2. Click anywhere in the notication screen, except for the button.
e Receiving Fax Record screen is displayed.
Faxing
>
Receiving Faxes on a Computer
>
Checking for New Faxes (Windows)
105
3. Check the date and the sender in the list, and then open the received le as a PDF.
Note:
❏Received faxes are automatically renamed using the following naming format.
YYYYMMDDHHMMSS_xxxxxxxxxx_nnnnn (Year/Month/Day/Hour/Minute/Second_sender’s number)
❏You can also open the received fax folder directly when you right-click the icon. For details, see Optional Settings in
the FAX Utility and its help (displayed on the main window).
Checking for New Faxes (Mac OS)
You can check for new faxes using one of the following methods. is is available only on computers set to "Save"
(save faxes on this computer).
❏Open the received fax folder (specied in Received Fax Output Settings.)
❏Open the Fax Receive Monitor and click Check new faxes now.
❏Notication that new faxes have been received
Select the Notify me of new faxes via a dock icon in the Fax Receive Monitor > Preferences in the FAX Utility,
the fax receive monitor icon on the Dock jumps to notify you that new faxes have arrived.
Open the Received Fax Folder from Received Fax Monitor (Mac OS)
You can open the save folder from the computer specied to receive faxes when selecting "Save" (save faxes on
this computer).
1. Click the received fax monitor icon on the Dock to open Fax Receive Monitor.
2. Select the printer and click Open folder, or double click the printer name.
3. Check the date and the sender in the le name, and then open the PDF le.
Note:
Received faxes are automatically renamed using the following naming format.
YYYYMMDDHHMMSS_xxxxxxxxxx_nnnnn (Year/Month/Day/Hour/Minute/Second_sender's number)
Information sent from the sender is displayed as the sender's number. is number may not be displayed depending on
the sender.
Canceling the Feature that Saves Incoming Faxes to the Computer
You can cancel saving faxes to the computer by using the FAX Utility.
For details, see Basic Operations in the FAX Utility help (displayed on the main window).
Note:
❏If there are any faxes that have not been saved to the computer, you cannot cancel the feature that saves faxes on the
computer.
❏You can also change the settings on the printer. Contact your administrator for information on canceling settings to save
received faxes on the computer.
Faxing
>
Receiving Faxes on a Computer
>
Canceling the Feature that Saves Incoming Faxes to the Computer
106
Maintaining the Printer
Checking the Status of Consumable....................................109
Cleaning the Paper Path for Paper Feeding Problems....................... 109
Improving Print, Copy, Scan, and Fax Quality.............................111
Cleaning the Printer...............................................121
Cleaning Spilled ink............................................... 121
Checking the Total Number of Pages Fed rough the Printer.................122
Saving Power.................................................... 122
Installing or Uninstalling Applications Separately..........................123
Transporting and Storing the Printer...................................128
Checking the Status of Consumable
You can check the approximate service life of the maintenance box from the printer's control panel. Select on
the home screen.
To conrm the actual ink remaining, visually check the ink levels in all of the printer's tanks.
c
Important:
Prolonged use of the printer when the ink level is below the lower line could damage the printer.
Note:
You can also check the approximate ink levels and the approximate service life of the maintenance box from the status
monitor on the printer driver. See the related information link below for details.
Related Information
&“Application for Printing from a Computer (Windows Printer Driver)” on page 243
&“Guide to Mac OS Printer Driver” on page 245
&“Relling the Ink Tank” on page 193
&“Replacing a Maintenance Box” on page 197
Cleaning the Paper Path for Paper Feeding Problems
When paper is not fed from paper cassette correctly, clean the roller inside.
1. Turn o the printer by pressing the
P
button.
2. Unplug the power cord, and then disconnect the power cord.
Maintaining the Printer
>
Cleaning the Paper Path for Paper Feeding Problems
109
3. Make sure that the ink tank cap is securely closed.
c
Important:
If the ink tank cap is not securely closed, ink may leak.
4. Close the document cover, the ADF cover, and the printer cover.
5. Slide out the paper cassette, and then remove the paper.
6. Stand the printer on its side with the printer's ink tank at the bottom.
!
Caution:
Be careful not to trap your hand or ngers when standing the printer. Otherwise you may be injured.
Maintaining the Printer
>
Cleaning the Paper Path for Paper Feeding Problems
110
c
Important:
Do not leave the printer standing for a long time.
7. Dampen a so cloth with water, wring it out thoroughly, and then wipe the roller while rotating it with the
cloth.
8. Return the printer to its normal position, and then insert the paper cassette.
9. Connect the power cord.
Improving Print, Copy, Scan, and Fax Quality
Checking and Cleaning the Print Head
If the nozzles are clogged, the printouts become faint, there is visible banding, or unexpected colors appear. If the
nozzles are severely clogged, a blank sheet will be printed. When print quality has declined, rst use the nozzle
check feature to check if the nozzles are clogged. If the nozzles are clogged, clean the print head.
c
Important:
❏Do not open the printer cover or turn o the printer during head cleaning. If the head cleaning is incomplete, you
may not be able to print.
❏Head cleaning consumes ink and should not be performed more than necessary.
❏When ink is low, you may not be able to clean the print head.
❏If print quality has not improved aer repeating nozzle check and head cleaning 3 times, wait for at least 12
hours without printing, and then run the nozzle check again and repeat the head cleaning if necessary. We
recommend turning o the printer by using the
P
button. If print quality has still not improved, run Power
Cleaning.
❏To prevent the print head from drying out, do not unplug the printer while the power is on.
1. Select Maintenance on the printer's control panel.
2. Select Print Head Nozzle Check.
Maintaining the Printer
>
Improving Print, Copy, Scan, and Fax Quality
>
Checking and Cleaning the Print Head
111
3. Follow the on-screen instructions to load paper and print the nozzle check pattern.
4. Check the printed pattern to see if the print head nozzles are clogged.
❏A:
All lines are printed. Select . No further steps are needed.
❏B or close to B
Some nozzles are clogged. Select , and then follow the on-screen instructions to clean the print head.
When cleaning is nished, print the nozzle check pattern again.
❏C or close to C
If most lines are missing or not printed, this indicates most nozzles are clogged. Select to exit the nozzle
check feature, and then run Power Cleaning. For details, see "Related information" below.
5. Repeat cleaning and printing the pattern until all lines are printed completely.
c
Important:
If print quality has not improved aer repeating nozzle check and head cleaning 3 times, wait for at least 12 hours
without printing, and then run the nozzle check again and repeat the head cleaning if necessary. We recommend
turning o the printer by using the
P
button. If print quality has still not improved, run Power Cleaning.
Note:
You can also check and clean the print head from the printer driver. See the related information link below for details.
Related Information
&“Running Power Cleaning” on page 112
&“Application for Printing from a Computer (Windows Printer Driver)” on page 243
&“Guide to Mac OS Printer Driver” on page 245
Running Power Cleaning
e Power Cleaning utility allows you to replace all of the ink inside the ink tubes. In the following situations, you
may need to use this feature to improve the print quality.
❏You printed or performed head cleaning when the ink levels were too low to be seen in the ink tank windows.
Maintaining the Printer
>
Improving Print, Copy, Scan, and Fax Quality
>
Running Power Cleaning
112
❏You performed the nozzle check and head cleaning 3 times and then waited for at least 12 hours without
printing, but print quality still did not improve.
Before running this feature, read the following instructions.
c
Important:
Make sure that there is enough ink in the ink tanks.
Visually check all ink tanks are at least a third full. Low ink levels during Power Cleaning could damage the
product.
c
Important:
An interval of 12 hours is required between each Power Cleaning.
Normally, a single Power Cleaning should resolve the print quality issue within 12 hours. erefore, to avoid
unnecessary ink usage, you must wait 12 hours before you try it again.
c
Important:
Maintenance box replacement may be required.
Ink will be deposited to the maintenance box. If it becomes full, you must prepare and install a replacement
maintenance box to continue printing.
Note:
When the ink levels or the free space in the maintenance box are insucient for Power Cleaning, you cannot run this
feature. Even in this case, the levels and the free space for printing may remain.
1. Select Maintenance on the printer's control panel.
2. Select Power Cleaning.
3. Follow the on-screen instructions to run the Power Cleaning feature.
Note:
If you cannot run this feature, solve the problems that are displayed on the screen. Next, follow this procedure from step
1 to run this feature again.
4. Aer running this feature, run the nozzle check to make sure the nozzles are not clogged.
For details on how to run the nozzle check, see the related information link below.
c
Important:
If print quality has not improved aer running Power Cleaning, wait for at least 12 hours without printing, and
then print the nozzle check pattern again. Run Print Head Cleaning or Power Cleaning again depending on the
printed pattern. If quality still does not improve, contact Epson support.
Note:
You can also run power cleaning from the printer driver. See the related information link below for details.
Related Information
&“Checking and Cleaning the Print Head” on page 111
Maintaining the Printer
>
Improving Print, Copy, Scan, and Fax Quality
>
Running Power Cleaning
113
&“Application for Printing from a Computer (Windows Printer Driver)” on page 243
&“Guide to Mac OS Printer Driver” on page 245
Preventing nozzle clogging
Always use the power button when turning the printer on and o.
Check that the power light is o before you disconnect the power cord.
e ink itself can dry out if it is not covered. Just like placing a cap on a fountain pen or an oil pen to prevent it
from drying, make sure the print head is capped properly to prevent the ink from drying.
When the power cord is unplugged or a power outage occurs while the printer is in operation, the print head may
not be capped properly. If the print head is le as it is, it will dry out causing nozzles (ink outlets) to clog.
In these cases, turn the printer on and o again as soon as possible to cap the print head.
Aligning the Print Head
If you notice a misalignment of vertical lines or blurred images, align the print head.
1. Select Maintenance on the printer's control panel.
2. Select Print Head Alignment.
3. Select one of the alignment menus.
❏Vertical lines look misaligned or the printouts look blurry : Select Vertical Alignment.
❏Horizontal banding occurs at regular intervals: Select Horizontal Alignment.
4. Follow the on-screen instructions to load paper and print the alignment pattern.
Cleaning the Paper Path for Ink Smears
When the printouts are smeared or scued, clean the roller inside.
c
Important:
Do not use tissue paper to clean the inside of the printer. e print head nozzles may be clogged with lint.
1. Select Maintenance on the printer's control panel.
2. Select Paper Guide Cleaning.
3. Follow the on-screen instructions to load paper and clean the paper path.
Repeat this procedure until the paper is not smeared with ink.
Cleaning the Scanner Glass
When the copies or scanned images are smeared, clean the scanner glass.
Maintaining the Printer
>
Improving Print, Copy, Scan, and Fax Quality
>
Cleaning the Scanner Glass
114
!
Caution:
Be careful not to trap your hand or ngers when opening or closing the document cover. Otherwise you may be
injured.
c
Important:
Never use alcohol or thinner to clean the printer. ese chemicals can damage the printer.
1. Open the document cover.
2. Use a so, dry, clean cloth to clean the surface of the scanner glass.
c
Important:
❏If the glass surface is stained with grease or some other hard-to-remove material, use a small amount of
glass cleaner and a so cloth to remove it. Wipe o all remaining liquid.
❏Do not press the glass surface too hard.
❏Be careful not to scratch or damage the surface of the glass. A damaged glass surface can decrease the scan
quality.
Cleaning the ADF
When the copied or scanned images from the ADF are smeared or the originals do not feed in the ADF correctly,
clean the ADF.
c
Important:
Never use alcohol or thinner to clean the printer. ese chemicals can damage the printer.
Maintaining the Printer
>
Improving Print, Copy, Scan, and Fax Quality
>
Cleaning the ADF
115
3. Close the ADF cover, and then open the document cover.
4. Clean the part that is shown in the illustration.
c
Important:
❏If the glass surface is stained with grease or some other hard-to-remove material, use a small amount of
glass cleaner and a so cloth to remove it. Wipe o all remaining liquid.
❏Do not press the glass surface too hard.
❏Be careful not to scratch or damage the surface of the glass. A damaged glass surface can decrease the scan
quality.
Maintaining the Printer
>
Improving Print, Copy, Scan, and Fax Quality
>
Cleaning the ADF
117
5. If the problem cannot be cleared, turn o the printer by pressing the
P
button, open the ADF cover, and then
raise the ADF input tray.
6. Clean the part that is shown in the illustration.
Cleaning the Translucent Film
When the printout is not improved aer aligning the print head or cleaning the paper path, the translucent lm
inside the printer may be smeared.
Items required:
❏Cotton swabs (several)
❏Water with a few drops of detergent (2 to 3 drops of detergent in 1/4 cup of tap water)
❏Light for checking smears
Maintaining the Printer
>
Improving Print, Copy, Scan, and Fax Quality
>
Cleaning the Translucent Film
118
c
Important:
Do not use cleaning liquid other than water with a few drops of detergent.
1. Tur n o the printer by pressing the
P
button.
2. Open the printer cover.
3. Check if the translucent lm is smeared. Smears are easier to see if you use a light.
If there are smears (such as nger marks or grease) on the translucent lm (A), go to the next step.
A: Translucent lm
B: Rail
Maintaining the Printer
>
Improving Print, Copy, Scan, and Fax Quality
>
Cleaning the Translucent Film
119
c
Important:
Be careful not to touch the rail (B). Otherwise, you may not be able to print. Do not wipe o the grease on the
rail, because this is necessary for operations.
4. Moisten a cotton swab with the water with a few drops of detergent so that it is not dripping water, and then
wipe the smeared part.
c
Important:
Wipe o the smear gently. If you press the cotton swab too hard to the lm, the springs of the lm may be
dislocated and the printer may be damaged.
5. Use a new dry cotton swab to wipe the lm.
c
Important:
Do not leave any bers on the lm.
Note:
To prevent the smear from spreading, frequently replace the cotton swab with a new one.
6. Repeat steps 4 and 5 until the lm is not smeared.
7. Visually check that the lm is not smeared.
Maintaining the Printer
>
Improving Print, Copy, Scan, and Fax Quality
>
Cleaning the Translucent Film
120
Cleaning the Printer
If the components and the case are dirty or dusty, turn o the printer and clean them using a so, clean cloth that
has been dampened with water. If you cannot remove the dirt, try adding a small amount of mild detergent to the
damp cloth.
c
Important:
❏Be careful not to get water onto the printer mechanism or any electrical components. Otherwise, the printer
could be damaged.
❏Never use alcohol or paint thinner to clean the components and the case. ese chemicals can damage them.
❏Do not touch the parts shown in the following illustration. Doing so may cause a malfunction.
Cleaning Spilled ink
If ink has been spilled, clean it up in the following ways.
❏If ink adheres to the area around the tank, wipe it o using a napless, clean cloth or cotton swab.
❏If ink spills on the desk or oor, wipe it o immediately. When ink is dried, it will be dicult to remove the
smear. To prevent the smear from spreading, blot the ink with a dry cloth, and then wipe it with a moist cloth.
❏If ink gets on your hands, wash them with water and soap.
Maintaining the Printer
>
Cleaning Spilled ink
121
Checking the Total Number of Pages Fed Through the
Printer
You can check the total number of pages fed through the printer. e information is printed together with the
nozzle check pattern.
1. Select Maintenance on the printer's control panel.
2. Select Print Head Nozzle Check.
3. Follow the on-screen instructions to load paper and print the nozzle check pattern.
Note:
You can also check the total number of pages fed from the printer driver. See the related information link below for details.
Related Information
&“Application for Printing from a Computer (Windows Printer Driver)” on page 243
&“Guide to Mac OS Printer Driver” on page 245
Saving Power
e printer enters sleep mode or turns o automatically if no operations are performed for a set period. You can
adjust the time before power management is applied. Any increase will aect the product's energy eciency. Please
consider the environment before making any change.
Depending on the location of purchase, the printer may have a feature that turns it o automatically if it is not
connected to the network for 30 minutes.
Saving Power (Control Panel)
1. Select Settings on the home screen.
2. Select General Settings > Basic Settings.
3. Do one of the following.
Note:
Your produc t may have the Power O Settings or Power O Timer feature depending on the location of purchase.
❏Select Sleep Timer or Power O Settings > Power O If Inactive or Power O If Disconnected, and then
make settings.
❏Select Sleep Timer or Power O Timer, and then make settings.
Maintaining the Printer
>
Saving Power
>
Saving Power (Control Panel)
122
Installing or Uninstalling Applications Separately
Connect your computer to the network and install the latest version of applications from the website. Log in to
your computer as an administrator. Enter the administrator password if the computer prompts you.
Installing the Applications Separately
Note:
When reinstalling an application, you need to uninstall it rst.
1. Make sure the printer and the computer are available for communication, and the printer is connected to the
Internet.
2. Start EPSON Soware Updater.
e screenshot is an example on Windows.
3. For Windows, select your printer, and then click to check for the latest available applications.
4. Select the items you want to install or update, and then click the install button.
c
Important:
Do not turn o or unplug the printer until the update is complete. Doing so may result in malfunction of the
printer.
Maintaining the Printer
>
Installing or Uninstalling Applications Separately
>
Installing the Applications Separ
…
123
Note:
❏You can download the latest applications from the Epson website.
http://www.epson.com
❏If you use Windows Server operating systems, you cannot use Epson Soware Updater. Download the latest
applications from the Epson website.
Related Information
&“Application for Updating Soware and Firmware (EPSON Soware Updater)” on page 251
&“Uninstalling Applications” on page 125
Checking if a genuine Epson printer driver is installed - Windows
You can check if a genuine Epson printer driver is installed on your computer by using one of the following
methods.
Select Control Panel > View devices and printers (Printers, Printers and Faxes), and then do the following to
open the print server properties window.
❏Windows Windows 10/Windows 8.1/Windows 8/Windows 7/Windows Server 2019/Windows Server 2016/
Windows Server 2012 R2/Windows Server 2012/Windows Server 2008 R2
Click the printer icon, and then click Print server properties at the top of the window.
❏Windows Vista/Windows Server 2008
Right-click on the Printers folder, and then click Run as administrator > Server Properties.
❏Windows XP/Windows Server 2003 R2/Windows Server 2003
From the File menu, select Server Properties.
Click the Driver tab. If your printer name is displayed in the list, a genuine Epson printer driver is installed on
your computer.
Maintaining the Printer
>
Installing or Uninstalling Applications Separately
>
Installing the Applications Separ
…
124
Related Information
&“Installing the Applications Separately” on page 123
Checking if a genuine Epson printer driver is installed - Mac OS
You can check if a genuine Epson printer driver is installed on your computer by using one of the following
methods.
Select System Preferences from the Apple menu > Printers & Scanners (or Print & Scan, Print & Fax), and then
select the printer. Click Options & Supplies, and if the Options tab and Utility tab are displayed on the window, a
genuine Epson printer driver is installed on your computer.
Related Information
&“Installing the Applications Separately” on page 123
Adding the Printer (for Mac OS Only)
1. Select System Preferences from the Apple menu > Printers & Scanners (or Print & Scan, Print & Fax).
2. Click +, and then select Add Other Printer or Scanner.
3. Select your printer, and then select your printer from the Use.
4. Click Add.
Note:
If your printer is not listed, check that it is correctly connected to the computer and that the printer is on.
Uninstalling Applications
Log in to your computer as an administrator. Enter the administrator password if the computer prompts you.
Maintaining the Printer
>
Installing or Uninstalling Applications Separately
>
Uninstalling Applications
125
Uninstalling Applications - Windows
1. Press the
P
button to turn o the printer.
2. Quit all running applications.
3. Open Control Panel:
❏Windows 10/Windows Server 2019/Windows Server 2016
Click on the start button, and then select Windows System > Control Panel.
❏Windows 8.1/Windows 8/Windows Server 2012 R2/Windows Server 2012
Select Desktop > Settings > Control Panel.
❏Windows 7/Windows Vista/Windows XP/Windows Server 2008 R2/Windows Server 2008/Windows Server
2003 R2/Windows Server 2003
Click the start button and select Control Panel.
4. Open Uninstall a program (or Add or Remove Programs):
❏Windows 10/Windows 8.1/Windows 8/Windows 7/Windows Vista/Windows Server 2019/Windows Server
2016/Windows Server 2012 R2/Windows Server 2012/Windows Server 2008 R2/Windows Server 2008
Select Uninstall a program in Programs.
❏Windows XP/Windows Server 2003 R2/Windows Server 2003
Click Add or Remove Programs.
5. Select the application you want to uninstall.
You cannot uninstall the printer driver if there is any print jobs. Delete or wait to be printed the jobs before
uninstalling.
6. Uninstall the applications:
❏Windows 10/Windows 8.1/Windows 8/Windows 7/Windows Vista/Windows Server 2019/Windows Server
2016/Windows Server 2012 R2/Windows Server 2012/Windows Server 2008 R2/Windows Server 2008
Click Uninstall/Change or Uninstall.
❏Windows XP/Windows Server 2003 R2/Windows Server 2003
Click Change/Remove or Remove.
Note:
If the User Account Control window is displayed, click Continue.
7. Follow the on-screen instructions.
Uninstalling Applications - Mac OS
1. Download the Uninstaller using EPSON Soware Updater.
Once you have downloaded the Uninstaller, you do not need to download it again each time you uninstall the
application.
2. Press the
P
button to turn o the printer.
Maintaining the Printer
>
Installing or Uninstalling Applications Separately
>
Uninstalling Applications
126
3. To uninstall the printer driver or PC-FAX driver, select System Preferences from the Apple menu > Printers &
Scanners (or Print & Scan, Print & Fax), and then remove the printer from the enabled printers list.
4. Quit all running applications.
5. Select Go > Applications > Epson Soware > Uninstaller.
6. Select the application you want to uninstall, and then click Uninstall.
c
Important:
e Uninstaller removes all drivers for Epson inkjet printers on the computer. If you use multiple Epson inkjet
printers and you only want to delete some drivers, delete all of them rst, and then install the necessary printer
driver again.
Note:
If you cannot nd the application you want to uninstall in the application list, you cannot uninstall using the
Uninstaller. In this situation, select Go > Applications > Epson Soware, select the application you want to uninstall,
and then drag it to the trash icon.
Related Information
&“Application for Updating Soware and Firmware (EPSON Soware Updater)” on page 251
Updating Applications and Firmware
You may be able to clear certain problems and improve or add functions by updating the applications and the
rmware. Make sure you use the latest version of the applications and rmware.
1. Make sure that the printer and the computer are connected, and the computer is connected to the internet.
2. Start EPSON Soware Updater, and update the applications or the rmware.
c
Important:
Do not turn o the computer or the printer until the update is complete; otherwise, the printer may
malfunction.
Note:
If you cannot nd the application you want to update in the list, you cannot update using the EPSON Soware Updater.
Check for the latest versions of the applications from your local Epson website.
http://www.epson.com
Related Information
&“Application for Updating Soware and Firmware (EPSON Soware Updater)” on page 251
Updating the Printer's Firmware Using the Control Panel
If the printer can be connected to the Internet, you can update the printer's rmware using the control panel. You
can also set the printer to regularly check for rmware updates and notify you if any are available.
Maintaining the Printer
>
Installing or Uninstalling Applications Separately
>
Updating Applications and Firm
…
127
Related Information
&“Firmware Update” on page 264
Transporting and Storing the Printer
When you need to store the printer or transport it when moving or for repairs, follow the steps below to pack the
printer.
1. Turn o the printer by pressing the
P
button.
2. Make sure the power light turns o, and then unplug the power cord.
c
Important:
Unplug the power cord when the power light is o. Otherwise, the print head does not return to the home
position causing the ink to dry, and printing may become impossible.
3. Disconnect all cables such as the power cord and USB cable.
4. Remove all of the paper from the printer.
5. Make sure there are no originals on the printer.
6. Close the document cover if it is open.
7. Open the printer cover. Secure the print head to the case with tape.
!
Caution:
Be careful not to trap your hand or ngers when opening or closing the print cover. Otherwise you may be
injured.
Maintaining the Printer
>
Transporting and Storing the Printer
128
c
Important:
❏When storing or transporting the printer, place the printer in the plastic bag and fold it closed. Avoid tilting the
printer, placing it vertically, or turning it upside down; otherwise ink may leak.
❏When liing the printer, place your hands in the positions shown below.
Maintaining the Printer
>
Transporting and Storing the Printer
131
c
Important:
❏When storing or transporting an ink bottle, do not tilt the bottle and do not subject it to impacts or temperature
changes. Otherwise, ink may leak even if the cap on the ink bottle is tightened securely. Be sure to keep the ink
bottle upright when tightening the cap, and take precautions to prevent ink from leaking when transporting the
bottle, for example, putting the bottle in a bag.
❏Do not put opened ink bottles in the box with printer.
When you use the printer again, make sure you remove the tape securing the print head. If print quality has
declined the next time you print, clean and align the print head.
Related Information
&“Checking and Cleaning the Print Head” on page 111
&“Aligning the Print Head” on page 114
Maintaining the Printer
>
Transporting and Storing the Printer
132
Solving Problems
e Printer Does Not Work as Expected.................................134
A Message is Displayed on the LCD Screen...............................183
Paper Gets Jammed................................................184
It is Time to Rell the Ink........................................... 192
It is Time to Replace the Maintenance Box...............................196
Printing, Copying, Scanning, and Faxing Quality is Poor.....................198
Cannot Solve Problem..............................................215
The Printer Does Not Work as Expected
The Printer Does Not Turn On or O
Power Does Not Turn On
e following causes can be considered.
The power cord is not plugged in properly to the electrical outlet.
Solutions
Make sure the power cord is securely plugged in.
The
P
button was not pressed for long enough.
Solutions
Hold down the
P
button for a little longer.
Power Does Not Turn O
The
P
button was not pressed for long enough.
Solutions
Hold down the
P
button for a little longer. If you still cannot turn o the printer, unplug the power cord.
To prevent the print head from drying out, turn the printer back on and turn it o by pressing the
P
button.
Power Turns O Automatically
The Power O Settings or Power O Timer feature is enabled.
Solutions
❏Select Settings > General Settings > Basic Settings > Power O Settings, and then disable the Power
O If Inactive and Power O If Disconnected settings.
❏Select Settings > General Settings > Basic Settings, and then disable the Power O Timer Setting.
Note:
Your product may have the Power O Settings or Power O Timer feature depending on the location of purchase.
Paper Does Not Feed Properly
No Paper Feeds
e following causes can be considered.
Solving Problems
>
The Printer Does Not Work as Expected
>
Paper Does Not Feed Properly
134
The installation location is inappropriate.
Solutions
Place the printer on a at surface and operate in the recommended environmental conditions.
&“Environmental Specications” on page 271
Unsupported paper is being used.
Solutions
Use paper supported by this printer.
&“Available Paper and Capacities” on page 239
&“Unavailable Paper Types” on page 241
Paper handling is inappropriate.
Solutions
Follow paper handling precautions.
&“Paper Handling Precautions” on page 29
Too many sheets are loaded in the printer.
Solutions
Do not load more than the maximum number of sheets specied for the paper.
&“Available Paper and Capacities” on page 239
The paper settings on the printer are incorrect.
Solutions
Make sure the paper size and paper type settings match the actual paper size and paper type loaded in the
printer.
&“Paper Size and Type Settings” on page 29
Paper slips when paper dust adheres to the roller.
Solutions
Clean the roller.
&“Cleaning the Paper Path for Paper Feeding Problems” on page 109
Paper Feeds at a Slant
e following causes can be considered.
The installation location is inappropriate.
Solutions
Place the printer on a at surface and operate in the recommended environmental conditions.
&“Environmental Specications” on page 271
Solving Problems
>
The Printer Does Not Work as Expected
>
Paper Does Not Feed Properly
135
Unsupported paper is being used.
Solutions
Use paper supported by this printer.
&“Available Paper and Capacities” on page 239
&“Unavailable Paper Types” on page 241
Paper handling is inappropriate.
Solutions
Follow paper handling precautions.
&“Paper Handling Precautions” on page 29
The paper is loaded incorrectly.
Solutions
Load paper in the correct direction, and slide the edge guide against the edge of the paper.
&“Loading Paper” on page 31
Too many sheets are loaded in the printer.
Solutions
Do not load more than the maximum number of sheets specied for the paper.
&“Available Paper and Capacities” on page 239
The paper settings on the printer are incorrect.
Solutions
Make sure the paper size and paper type settings match the actual paper size and paper type loaded in the
printer.
&“Paper Size and Type Settings” on page 29
Paper slips when paper dust adheres to the roller.
Solutions
Clean the roller.
&“Cleaning the Paper Path for Paper Feeding Problems” on page 109
Several Sheets of Paper are Fed at a Time
e following causes can be considered.
The installation location is inappropriate.
Solutions
Place the printer on a at surface and operate in the recommended environmental conditions.
&“Environmental Specications” on page 271
Solving Problems
>
The Printer Does Not Work as Expected
>
Paper Does Not Feed Properly
136
Unsupported paper is being used.
Solutions
Use paper supported by this printer.
&“Available Paper and Capacities” on page 239
&“Unavailable Paper Types” on page 241
Paper handling is inappropriate.
Solutions
Follow paper handling precautions.
&“Paper Handling Precautions” on page 29
The paper is moist or damp.
Solutions
Load new paper.
Static electricity is causing sheets of paper to stick to each other.
Solutions
Fan the paper before loading. If the paper still does not feed, load one sheet of paper at a time.
Too many sheets are loaded in the printer.
Solutions
Do not load more than the maximum number of sheets specied for the paper.
&“Available Paper and Capacities” on page 239
The paper settings on the printer are incorrect.
Solutions
Make sure the paper size and paper type settings match the actual paper size and paper type loaded in the
printer.
&“Paper Size and Type Settings” on page 29
Paper slips when paper dust adheres to the roller.
Solutions
Clean the roller.
&“Cleaning the Paper Path for Paper Feeding Problems” on page 109
Ejected Paper Falls from the Output Tray
The stopper is not extended.
Solutions
If ejected paper falls from the output tray, slide out the stopper to prevent the paper from falling.
Solving Problems
>
The Printer Does Not Work as Expected
>
Paper Does Not Feed Properly
137
Paper is Ejected During Printing
Letterhead is not selected as the paper type.
Solutions
When you load letterhead paper (paper on which information such as the sender's name or corporation
name are pre-printed in the header), select Letterhead as the paper type setting.
Original Does Not Feed in the ADF
e following causes can be considered.
Originals that are not supported by the ADF are being used.
Solutions
Use originals supported by the ADF.
&“ADF Specications” on page 266
The originals are loaded incorrectly.
Solutions
Load originals in the correct direction, and slide the ADF edge guides against the edges of the originals.
Too many originals are loaded in the ADF.
Solutions
Do not load originals above the line indicated by the triangle symbol on the ADF.
The original slips when paper dust adheres to the roller.
Solutions
Clean the inside of the ADF.
&“Cleaning the ADF” on page 115
Originals are not detected.
Solutions
On the screen for copy or scan, or fax, check that the ADF icon is on. If it is o, place the originals again.
Solving Problems
>
The Printer Does Not Work as Expected
>
Paper Does Not Feed Properly
138
An original is placed on the scanner glass.
Solutions
Make sure that an original has not been placed on the scanner glass.
Cannot Print
Cannot Print from Windows
Make sure the computer and the printer are connected correctly.
e cause and solution to the problem dier depending on whether or not they are connected.
Checking the Connection Status
Use Epson Printer Connection Checker to check the connection status for the computer and the printer. You may
be able to solve the problem depending on the results of the check.
1. Double-click the Epson Printer Connection Checker icon on the desktop.
Epson Printer Connection Checker starts.
If there is no icon on the desktop, follow the methods below to start Epson Printer Connection Checker.
❏Windows 10
Click the start button, and then select Epson Soware > Epson Printer Connection Checker.
❏Windows 8.1/Windows 8
Enter the application name in the search charm, and then select the displayed icon.
❏Windows 7
Click the start button, and then select All Programs > Epson Soware > Epson Printer Connection
Checker.
2. Follow the on-screen instructions to check.
Note:
If the printer name is not displayed, install a genuine Epson printer driver.
“Checking if a genuine Epson printer driver is installed - Windows” on page 124
When you have identied the problem, follow the solution displayed on the screen.
When you cannot solve the problem, check the following according to your situation.
❏e printer is not recognized over a network connection
“Cannot connect to a Network” on page 140
❏e printer is not recognized using a USB connection
“e Printer Cannot Connect by USB (Windows)” on page 143
❏e printer is recognized, but printing cannot be performed.
“Cannot Print Even ough a Connection has been Established (Windows)” on page 143
Solving Problems
>
The Printer Does Not Work as Expected
>
Cannot Print
139
Cannot connect to a Network
e problem could be one of the following issues.
Something is wrong with the network devices for Wi-Fi connection.
Solutions
Turn o the devices you want to connect to the network. Wait for about 10 seconds, and then turn on the
devices in the following order; wireless router, computer or smart device, and then printer. Move the
printer and computer or smart device closer to the wireless router to help with radio wave
communication, and then try to make network settings again.
Devices cannot receive signals from the wireless router because they are too far apart.
Solutions
Aer moving the computer or the smart device and the printer closer to the wireless router, turn o the
wireless router, and then turn it back on.
When changing the wireless router, the settings do not match the new router.
Solutions
Make the connection settings again so that they match the new wireless router.
&“When Replacing the Wireless Router” on page 219
The SSIDs connected from the computer or smart device and computer are dierent.
Solutions
When you are using multiple wireless routers at the same time or the wireless router has multiple SSIDs
and devices are connected to dierent SSIDs, you cannot connect to the wireless router.
Connect the computer or smart device to the same SSID as the printer.
Solving Problems
>
The Printer Does Not Work as Expected
>
Cannot Print
140
❏Example of connecting to dierent SSIDs
❏Example of connecting to SSIDs with a dierent frequency range
A privacy separator on the wireless router is available.
Solutions
Most wireless routers have a separator function that blocks communication between devices within the
same SSID. If you cannot communicate between the printer and the computer or smart device even if
they are connected to the same network, disable the separator function on the wireless router. See the
manual provided with the wireless router for details.
The IP address is incorrectly assigned.
Solutions
If the IP address assigned to the printer is 169.254.XXX.XXX, and the subnet mask is 255.255.0.0, the IP
address may not be assigned correctly.
Select Settings > General Settings > Network Settings > Advanced on the printer’s control panel, and
then check the IP address and the subnet mask assigned to the printer.
Restart the wireless router or reset the network settings for the printer.
&“Re-setting the Network Connection” on page 219
Solving Problems
>
The Printer Does Not Work as Expected
>
Cannot Print
141
There is a problem with the network settings on the computer.
Solutions
Try accessing any website from your computer to make sure that your computer's network settings are
correct. If you cannot access any website, there is a problem on the computer.
Check the network connection of the computer. See the documentation provided with the computer for
details.
The printer has been connected by Ethernet using devices that support IEEE802.3az (Energy
Ecient Ethernet).
Solutions
When you connect the printer by Ethernet using devices that support IEEE802.3az (Energy Ecient
Ethernet), the following problems may occur depending on the hub or router that you are using.
❏Connection becomes unstable, the printer is connected and disconnected again and again.
❏Cannot connect to the printer.
❏e communication speed becomes slow.
Follow the steps below to disable IEEE802.3az for the printer and then connect.
1. Remove the Ethernet cable connected to the computer and the printer.
2. When IEEE802.3az for the computer is enabled, disable it.
See the documentation provided with the computer for details.
3. Connect the computer and the printer with an Ethernet cable directly.
4. On the printer, print a network connection report.
“Printing a Network Connection Report” on page 230
5. Check the printer's IP address on the network connection report.
6. On the computer, access Web Cong.
Launch a Web browser, and then enter the printer's IP address.
“Application for Conguring Printer Operations (Web Cong)” on page 249
7. Select Advanced Settings from the list at the top right of the window.
8. Select Network Settings > Wired LAN.
9. Select OFF for IEEE 802.3az.
10. Click Next.
11. Click OK.
12. Remove the Ethernet cable connected to the computer and the printer.
13. If you disabled IEEE802.3az for the computer in step 2, enable it.
Solving Problems
>
The Printer Does Not Work as Expected
>
Cannot Print
142
14. Connect the Ethernet cables that you removed in step 1 to the computer and the printer.
If the problem still occurs, devices other than the printer may be causing the problem.
The Printer Cannot Connect by USB (Windows)
e following causes can be considered.
The USB cable is not plugged into the electrical outlet correctly.
Solutions
Connect the USB cable securely to the printer and the computer.
There is a problem with the USB hub.
Solutions
If you are using a USB hub, try to connect the printer directly to the computer.
There is a problem with the USB cable or the USB inlet.
Solutions
If the USB cable cannot be recognized, change the port, or change the USB cable.
Cannot Print Even Though a Connection has been Established (Windows)
e following causes can be considered.
There is a problem with the software or data.
Solutions
❏Make sure that a genuine Epson printer driver (EPSON XXXXX) is installed. If a genuine Epson
printer driver is not installed, the available functions are limited. We recommend using a genuine
Epson printer driver.
❏If you are printing a large data size image, the computer may run out of memory. Print the image at a
lower resolution or a smaller size.
❏If you have tried all of the solutions and have not solved the problem, try uninstalling and then
reinstalling the printer driver.
❏You may be able to clear the problem by updating the soware to the latest version. To check the
soware status, use the soware update tool.
&“Checking if a genuine Epson printer driver is installed - Windows” on page 124
&“Checking if a genuine Epson printer driver is installed - Mac OS” on page 125
&“Installing or Uninstalling Applications Separately” on page 123
&“Updating Applications and Firmware” on page 127
There is a problem with the printer's status.
Solutions
Click EPSON Status Monitor 3 on the printer driver's Maintenance tab, and then check the printer
status. If EPSON Status Monitor 3 is disabled, click Extended Settings on the Maintenance tab, and
then select Enable EPSON Status Monitor 3.
Solving Problems
>
The Printer Does Not Work as Expected
>
Cannot Print
143
There is still a job waiting to be printed.
Solutions
Click Print Queue on the printer driver's Maintenance tab. If unnecessary data remains, select Cancel all
documents from the Printer menu.
The printer is pending or oine.
Solutions
Click Print Queue on the printer driver's Maintenance tab.
If the printer is oine or pending, clear the oine or pending setting from the Printer menu.
The printer is not selected as the default printer.
Solutions
Right-click the printer icon in Control Panel > View devices and printers (or Printers, Printers and
Faxes) and click Set as default printer.
Note:
If there are multiple printer icons, see the following to select the correct printer.
Example)
USB connection: EPSON XXXX Series
Network connection: EPSON XXXX Series (network)
If you install the printer driver multiple times, copies of the printer driver may be created. If copies such
as "EPSON XXXX Series (copy 1)" are created, right-click the copied driver icon, and then click Remove
Device.
Solving Problems
>
The Printer Does Not Work as Expected
>
Cannot Print
144
The printer port is not set correctly.
Solutions
Click Print Queue on the printer driver's Maintenance tab.
Make sure the printer port is set correctly as shown below in Property > Port from the Printer menu.
USB connection: USBXXX, Network connection: EpsonNet Print Port
Suddenly the Printer Cannot Print over a Network Connection
e problem could be one of the following issues.
The network environment has been changed.
Solutions
When you have changed the network environment, such as the wireless router or provider, try making
network settings for the printer again.
Connect the computer or smart device to the same SSID as the printer.
&“Re-setting the Network Connection” on page 219
Something is wrong with the network devices for Wi-Fi connection.
Solutions
Turn o the devices you want to connect to the network. Wait for about 10 seconds, and then turn on the
devices in the following order; wireless router, computer or smart device, and then printer. Move the
printer and computer or smart device closer to the wireless router to help with radio wave
communication, and then try to make network settings again.
The printer is not connected to the network.
Solutions
Select Settings > General Settings > Network Settings > Connection Check, and then print the network
connection report. If the report shows that the network connection failed, check the network connection
report and then follow the printed solutions.
There is a problem with the network settings on the computer.
Solutions
Try accessing any website from your computer to make sure that your computer's network settings are
correct. If you cannot access any website, there is a problem on the computer.
Check the network connection of the computer. See the documentation provided with the computer for
details.
Solving Problems
>
The Printer Does Not Work as Expected
>
Cannot Print
145
There is still a job waiting to be printed.
Solutions
Click Print Queue on the printer driver's Maintenance tab. If unnecessary data remains, select Cancel all
documents from the Printer menu.
The printer is pending or oine.
Solutions
Click Print Queue on the printer driver's Maintenance tab.
If the printer is oine or pending, clear the oine or pending setting from the Printer menu.
The printer is not selected as the default printer.
Solutions
Right-click the printer icon in Control Panel > View devices and printers (or Printers, Printers and
Faxes) and click Set as default printer.
Note:
If there are multiple printer icons, see the following to select the correct printer.
Example)
USB connection: EPSON XXXX Series
Network connection: EPSON XXXX Series (network)
If you install the printer driver multiple times, copies of the printer driver may be created. If copies such
as "EPSON XXXX Series (copy 1)" are created, right-click the copied driver icon, and then click Remove
Device.
Solving Problems
>
The Printer Does Not Work as Expected
>
Cannot Print
146
The printer port is not set correctly.
Solutions
Click Print Queue on the printer driver's Maintenance tab.
Make sure the printer port is set correctly as shown below in Property > Port from the Printer menu.
USB connection: USBXXX, Network connection: EpsonNet Print Port
Cannot Print from Mac OS
Make sure the computer and the printer are connected correctly.
e cause and solution to the problem dier depending on whether or not they are connected.
Checking the Connection Status
Use EPSON Status Monitor to check the connection status for the computer and the printer.
1. Select System Preferences from the Apple menu > Printers & Scanners (or Print & Scan, Print & Fax), and
then select the printer.
2. Click Options & Supplies > Utility > Open Printer Utility.
3. Click EPSON Status Monitor.
When the status of consumables is displayed, a connection has been successfully established between the computer
and the printer.
Check the following if a connection has not been established.
❏e printer is not recognized over a network connection
“Cannot connect to a Network” on page 147
❏e printer is not recognized using a USB connection
“e Printer Cannot Connect by USB (Mac OS)” on page 150
Check the following if a connection has been established.
❏e printer is recognized, but printing cannot be performed.
“Cannot Print Even ough a Connection has been Established (Mac OS)” on page 151
Cannot connect to a Network
e problem could be one of the following issues.
Something is wrong with the network devices for Wi-Fi connection.
Solutions
Turn o the devices you want to connect to the network. Wait for about 10 seconds, and then turn on the
devices in the following order; wireless router, computer or smart device, and then printer. Move the
Solving Problems
>
The Printer Does Not Work as Expected
>
Cannot Print
147
printer and computer or smart device closer to the wireless router to help with radio wave
communication, and then try to make network settings again.
Devices cannot receive signals from the wireless router because they are too far apart.
Solutions
Aer moving the computer or the smart device and the printer closer to the wireless router, turn o the
wireless router, and then turn it back on.
When changing the wireless router, the settings do not match the new router.
Solutions
Make the connection settings again so that they match the new wireless router.
&“When Replacing the Wireless Router” on page 219
The SSIDs connected from the computer or smart device and computer are dierent.
Solutions
When you are using multiple wireless routers at the same time or the wireless router has multiple SSIDs
and devices are connected to dierent SSIDs, you cannot connect to the wireless router.
Connect the computer or smart device to the same SSID as the printer.
❏Example of connecting to dierent SSIDs
Solving Problems
>
The Printer Does Not Work as Expected
>
Cannot Print
148
❏Example of connecting to SSIDs with a dierent frequency range
A privacy separator on the wireless router is available.
Solutions
Most wireless routers have a separator function that blocks communication between devices within the
same SSID. If you cannot communicate between the printer and the computer or smart device even if
they are connected to the same network, disable the separator function on the wireless router. See the
manual provided with the wireless router for details.
The IP address is incorrectly assigned.
Solutions
If the IP address assigned to the printer is 169.254.XXX.XXX, and the subnet mask is 255.255.0.0, the IP
address may not be assigned correctly.
Select Settings > General Settings > Network Settings > Advanced on the printer’s control panel, and
then check the IP address and the subnet mask assigned to the printer.
Restart the wireless router or reset the network settings for the printer.
&“Re-setting the Network Connection” on page 219
There is a problem with the network settings on the computer.
Solutions
Try accessing any website from your computer to make sure that your computer's network settings are
correct. If you cannot access any website, there is a problem on the computer.
Check the network connection of the computer. See the documentation provided with the computer for
details.
The printer has been connected by Ethernet using devices that support IEEE802.3az (Energy
Ecient Ethernet).
Solutions
When you connect the printer by Ethernet using devices that support IEEE802.3az (Energy Ecient
Ethernet), the following problems may occur depending on the hub or router that you are using.
❏Connection becomes unstable, the printer is connected and disconnected again and again.
❏Cannot connect to the printer.
Solving Problems
>
The Printer Does Not Work as Expected
>
Cannot Print
149
❏e communication speed becomes slow.
Follow the steps below to disable IEEE802.3az for the printer and then connect.
1. Remove the Ethernet cable connected to the computer and the printer.
2. When IEEE802.3az for the computer is enabled, disable it.
See the documentation provided with the computer for details.
3. Connect the computer and the printer with an Ethernet cable directly.
4. On the printer, print a network connection report.
“Printing a Network Connection Report” on page 230
5. Check the printer's IP address on the network connection report.
6. On the computer, access Web Cong.
Launch a Web browser, and then enter the printer's IP address.
“Application for Conguring Printer Operations (Web Cong)” on page 249
7. Select Advanced Settings from the list at the top right of the window.
8. Select Network Settings > Wired LAN.
9. Select OFF for IEEE 802.3az.
10. Click Next.
11. Click OK.
12. Remove the Ethernet cable connected to the computer and the printer.
13. If you disabled IEEE802.3az for the computer in step 2, enable it.
14. Connect the Ethernet cables that you removed in step 1 to the computer and the printer.
If the problem still occurs, devices other than the printer may be causing the problem.
The Printer Cannot Connect by USB (Mac OS)
e following causes can be considered.
The USB cable is not plugged into the electrical outlet correctly.
Solutions
Connect the USB cable securely to the printer and the computer.
There is a problem with the USB hub.
Solutions
If you are using a USB hub, try to connect the printer directly to the computer.
Solving Problems
>
The Printer Does Not Work as Expected
>
Cannot Print
150
There is a problem with the USB cable or the USB inlet.
Solutions
If the USB cable cannot be recognized, change the port, or change the USB cable.
Cannot Print Even Though a Connection has been Established (Mac OS)
e following causes can be considered.
There is a problem with the software or data.
Solutions
❏Make sure that a genuine Epson printer driver (EPSON XXXXX) is installed. If a genuine Epson
printer driver is not installed, the available functions are limited. We recommend using a genuine
Epson printer driver.
❏If you are printing a large data size image, the computer may run out of memory. Print the image at a
lower resolution or a smaller size.
❏If you have tried all of the solutions and have not solved the problem, try uninstalling and then
reinstalling the printer driver.
❏You may be able to clear the problem by updating the soware to the latest version. To check the
soware status, use the soware update tool.
&“Checking if a genuine Epson printer driver is installed - Windows” on page 124
&“Checking if a genuine Epson printer driver is installed - Mac OS” on page 125
&“Installing or Uninstalling Applications Separately” on page 123
&“Updating Applications and Firmware” on page 127
There is a problem with the status of the printer.
Solutions
Make sure the printer status is not Pause.
Select System Preferences from the Apple menu > Printers & Scanners (or Print & Scan, Print & Fax),
and then double-click the printer. If the printer is paused, click Resume.
User feature restrictions are enabled for the printer.
Solutions
e printer may not print when the user feature restriction is enabled. Contact your printer
administrator.
Suddenly the Printer Cannot Print over a Network Connection
e problem could be one of the following issues.
The network environment has been changed.
Solutions
When you have changed the network environment, such as the wireless router or provider, try making
network settings for the printer again.
Solving Problems
>
The Printer Does Not Work as Expected
>
Cannot Print
151
Connect the computer or smart device to the same SSID as the printer.
&“Re-setting the Network Connection” on page 219
Something is wrong with the network devices for Wi-Fi connection.
Solutions
Turn o the devices you want to connect to the network. Wait for about 10 seconds, and then turn on the
devices in the following order; wireless router, computer or smart device, and then printer. Move the
printer and computer or smart device closer to the wireless router to help with radio wave
communication, and then try to make network settings again.
The printer is not connected to the network.
Solutions
Select Settings > General Settings > Network Settings > Connection Check, and then print the network
connection report. If the report shows that the network connection failed, check the network connection
report and then follow the printed solutions.
There is a problem with the network settings on the computer.
Solutions
Try accessing any website from your computer to make sure that your computer's network settings are
correct. If you cannot access any website, there is a problem on the computer.
Check the network connection of the computer. See the documentation provided with the computer for
details.
The Print Settings Menu is Not Displayed.
e following causes can be considered.
The Epson Printer Driver has Not been Installed Correctly
Solutions
If the Print Settings menu is not displayed on macOS Catalina (10.15) or later, macOS High Sierra
(10.13), macOS Sierra (10.12), OS X El Capitan (10.11), OS X Yosemite (10.10), OS X Mavericks (10.9),
OS X Mountain Lion (10.8), the Epson printer driver has not been installed correctly. Enable it from the
following menu.
Select System Preferences from the Apple menu > Printers & Scanners (or Print & Scan, Print & Fax),
remove the printer, and then add the printer again. See the following to add a printer.
“Adding the Printer (for Mac OS Only)” on page 125
macOS Mojave (10.14) cannot access Print Settings in applications made by Apple such as TextEdit.
Solving Problems
>
The Printer Does Not Work as Expected
>
Cannot Print
152
Cannot Print from Smart Device
Make sure the smart device and the printer are connected correctly.
e cause and solution to the problem dier depending on whether or not they are connected.
Check the connection with the smart device
Use Epson Smart Panel to check the connection between the smart device and the printer.
Open the Epson Smart Panel. If you cannot connect to the printer, tap [+] at the top of the screen to reset.
If you are not using Epson Smart Panel, see the link below.
http://epson.sn
Cannot connect to a Network
e problem could be one of the following issues.
Something is wrong with the network devices for Wi-Fi connection.
Solutions
Turn o the devices you want to connect to the network. Wait for about 10 seconds, and then turn on the
devices in the following order; wireless router, computer or smart device, and then printer. Move the
printer and computer or smart device closer to the wireless router to help with radio wave
communication, and then try to make network settings again.
Devices cannot receive signals from the wireless router because they are too far apart.
Solutions
Aer moving the computer or the smart device and the printer closer to the wireless router, turn o the
wireless router, and then turn it back on.
When changing the wireless router, the settings do not match the new router.
Solutions
Make the connection settings again so that they match the new wireless router.
&“When Replacing the Wireless Router” on page 219
Solving Problems
>
The Printer Does Not Work as Expected
>
Cannot Print
153
The SSIDs connected from the computer or smart device and computer are dierent.
Solutions
When you are using multiple wireless routers at the same time or the wireless router has multiple SSIDs
and devices are connected to dierent SSIDs, you cannot connect to the wireless router.
Connect the computer or smart device to the same SSID as the printer.
❏Example of connecting to dierent SSIDs
❏Example of connecting to SSIDs with a dierent frequency range
A privacy separator on the wireless router is available.
Solutions
Most wireless routers have a separator function that blocks communication between devices within the
same SSID. If you cannot communicate between the printer and the computer or smart device even if
they are connected to the same network, disable the separator function on the wireless router. See the
manual provided with the wireless router for details.
The IP address is incorrectly assigned.
Solutions
If the IP address assigned to the printer is 169.254.XXX.XXX, and the subnet mask is 255.255.0.0, the IP
address may not be assigned correctly.
Solving Problems
>
The Printer Does Not Work as Expected
>
Cannot Print
154
Select Settings > General Settings > Network Settings > Advanced on the printer’s control panel, and
then check the IP address and the subnet mask assigned to the printer.
Restart the wireless router or reset the network settings for the printer.
&“Re-setting the Network Connection” on page 219
There is a problem with the network settings on the smart device.
Solutions
Try accessing any website from your smart device to make sure that your smart device's network settings
are correct. If you cannot access any website, there is a problem on the smart device.
Check the network connection of the computer. See the documentation provided with the smart device
for details.
Cannot Print Even Though a Connection has been Established (iOS)
e following causes can be considered.
Paper Setup Auto Display is disabled.
Solutions
Enable Paper Setup Auto Display in the following menu.
Settings > General Settings > Printer Settings > Paper Source Settings > Paper Setup Auto Display
AirPrint is disabled.
Solutions
Enable the AirPrint setting on Web Cong.
&“Application for Conguring Printer Operations (Web Cong)” on page 249
Suddenly the Printer Cannot Print over a Network Connection
e problem could be one of the following issues.
The network environment has been changed.
Solutions
When you have changed the network environment, such as the wireless router or provider, try making
network settings for the printer again.
Connect the computer or smart device to the same SSID as the printer.
&“Re-setting the Network Connection” on page 219
Something is wrong with the network devices for Wi-Fi connection.
Solutions
Turn o the devices you want to connect to the network. Wait for about 10 seconds, and then turn on the
devices in the following order; wireless router, computer or smart device, and then printer. Move the
Solving Problems
>
The Printer Does Not Work as Expected
>
Cannot Print
155
printer and computer or smart device closer to the wireless router to help with radio wave
communication, and then try to make network settings again.
The printer is not connected to the network.
Solutions
Select Settings > General Settings > Network Settings > Connection Check, and then print the network
connection report. If the report shows that the network connection failed, check the network connection
report and then follow the printed solutions.
There is a problem with the network settings on the smart device.
Solutions
Try accessing any website from your smart device to make sure that your smart device's network settings
are correct. If you cannot access any website, there is a problem on the smart device.
Check the network connection of the computer. See the documentation provided with the smart device
for details.
Printing received faxes is disabled under the current settings.
If Save to Computer is set to Yes , change the setting to Yes a nd Pr int . Or, disable Save to Inbox and Save to
Computer allows printing to be performed.
You c a n nd Save to Inbox and Save to Computer in Settings > General Settings > Fax Settings > Receive
Settings > Fax Output Settings.
Cannot Start Scanning
Cannot Start Scanning from Windows
Make sure the computer and the printer are connected correctly.
e cause and solution to the problem dier depending on whether or not they are connected.
Checking the Connection Status
Use Epson Printer Connection Checker to check the connection status for the computer and the printer. You may
be able to solve the problem depending on the results of the check.
Solving Problems
>
The Printer Does Not Work as Expected
>
Cannot Start Scanning
156
1. Double-click the Epson Printer Connection Checker icon on the desktop.
Epson Printer Connection Checker starts.
If there is no icon on the desktop, follow the methods below to start Epson Printer Connection Checker.
❏Windows 10
Click the start button, and then select Epson Soware > Epson Printer Connection Checker.
❏Windows 8.1/Windows 8
Enter the application name in the search charm, and then select the displayed icon.
❏Windows 7
Click the start button, and then select All Programs > Epson Soware > Epson Printer Connection
Checker.
2. Follow the on-screen instructions to check.
Note:
If the printer name is not displayed, install a genuine Epson printer driver.
“Checking if a genuine Epson printer driver is installed - Windows” on page 124
When you have identied the problem, follow the solution displayed on the screen.
When you cannot solve the problem, check the following according to your situation.
❏e printer is not recognized over a network connection
“Cannot connect to a Network” on page 157
❏e printer is not recognized using a USB connection
“e Printer Cannot Connect by USB (Windows)” on page 143
❏e printer is recognized, but scanning cannot be performed.
“Cannot Scan Even ough a Connection has been Correctly Established (Windows)” on page 160
Cannot connect to a Network
e problem could be one of the following issues.
Something is wrong with the network devices for Wi-Fi connection.
Solutions
Turn o the devices you want to connect to the network. Wait for about 10 seconds, and then turn on the
devices in the following order; wireless router, computer or smart device, and then printer. Move the
printer and computer or smart device closer to the wireless router to help with radio wave
communication, and then try to make network settings again.
Solving Problems
>
The Printer Does Not Work as Expected
>
Cannot Start Scanning
157
Devices cannot receive signals from the wireless router because they are too far apart.
Solutions
Aer moving the computer or the smart device and the printer closer to the wireless router, turn o the
wireless router, and then turn it back on.
When changing the wireless router, the settings do not match the new router.
Solutions
Make the connection settings again so that they match the new wireless router.
&“When Replacing the Wireless Router” on page 219
The SSIDs connected from the computer or smart device and computer are dierent.
Solutions
When you are using multiple wireless routers at the same time or the wireless router has multiple SSIDs
and devices are connected to dierent SSIDs, you cannot connect to the wireless router.
Connect the computer or smart device to the same SSID as the printer.
❏Example of connecting to dierent SSIDs
❏Example of connecting to SSIDs with a dierent frequency range
Solving Problems
>
The Printer Does Not Work as Expected
>
Cannot Start Scanning
158
A privacy separator on the wireless router is available.
Solutions
Most wireless routers have a separator function that blocks communication between devices within the
same SSID. If you cannot communicate between the printer and the computer or smart device even if
they are connected to the same network, disable the separator function on the wireless router. See the
manual provided with the wireless router for details.
The IP address is incorrectly assigned.
Solutions
If the IP address assigned to the printer is 169.254.XXX.XXX, and the subnet mask is 255.255.0.0, the IP
address may not be assigned correctly.
Select Settings > General Settings > Network Settings > Advanced on the printer’s control panel, and
then check the IP address and the subnet mask assigned to the printer.
Restart the wireless router or reset the network settings for the printer.
&“Re-setting the Network Connection” on page 219
There is a problem with the network settings on the computer.
Solutions
Try accessing any website from your computer to make sure that your computer's network settings are
correct. If you cannot access any website, there is a problem on the computer.
Check the network connection of the computer. See the documentation provided with the computer for
details.
The printer has been connected by Ethernet using devices that support IEEE802.3az (Energy
Ecient Ethernet).
Solutions
When you connect the printer by Ethernet using devices that support IEEE802.3az (Energy Ecient
Ethernet), the following problems may occur depending on the hub or router that you are using.
❏Connection becomes unstable, the printer is connected and disconnected again and again.
❏Cannot connect to the printer.
❏e communication speed becomes slow.
Follow the steps below to disable IEEE802.3az for the printer and then connect.
1. Remove the Ethernet cable connected to the computer and the printer.
2. When IEEE802.3az for the computer is enabled, disable it.
See the documentation provided with the computer for details.
3. Connect the computer and the printer with an Ethernet cable directly.
4. On the printer, print a network connection report.
“Printing a Network Connection Report” on page 230
5. Check the printer's IP address on the network connection report.
Solving Problems
>
The Printer Does Not Work as Expected
>
Cannot Start Scanning
159
6. On the computer, access Web Cong.
Launch a Web browser, and then enter the printer's IP address.
“Application for Conguring Printer Operations (Web Cong)” on page 249
7. Select Advanced Settings from the list at the top right of the window.
8. Select Network Settings > Wired LAN.
9. Select OFF for IEEE 802.3az.
10. Click Next.
11. Click OK.
12. Remove the Ethernet cable connected to the computer and the printer.
13. If you disabled IEEE802.3az for the computer in step 2, enable it.
14. Connect the Ethernet cables that you removed in step 1 to the computer and the printer.
If the problem still occurs, devices other than the printer may be causing the problem.
The Printer Cannot Connect by USB (Windows)
e following causes can be considered.
The USB cable is not plugged into the electrical outlet correctly.
Solutions
Connect the USB cable securely to the printer and the computer.
There is a problem with the USB hub.
Solutions
If you are using a USB hub, try to connect the printer directly to the computer.
There is a problem with the USB cable or the USB inlet.
Solutions
If the USB cable cannot be recognized, change the port, or change the USB cable.
Cannot Scan Even Though a Connection has been Correctly Established (Windows)
Scanning at a high resolution over a network.
Solutions
Try scanning at a lower resolution.
Solving Problems
>
The Printer Does Not Work as Expected
>
Cannot Start Scanning
160
Cannot Start Scanning from Mac OS
Make sure the computer and the printer are connected correctly.
e cause and solution to the problem dier depending on whether or not they are connected.
Checking the Connection Status
Use EPSON Status Monitor to check the connection status for the computer and the printer.
1. Select System Preferences from the Apple menu > Printers & Scanners (or Print & Scan, Print & Fax), and
then select the printer.
2. Click Options & Supplies > Utility > Open Printer Utility.
3. Click EPSON Status Monitor.
When the remaining ink levels are displayed, a connection has been successfully established between the computer
and the printer.
Check the following if a connection has not been established.
❏e printer is not recognized over a network connection
“Cannot connect to a Network” on page 161
❏e printer is not recognized using a USB connection
“e Printer Cannot Connect by USB (Mac OS)” on page 150
Check the following if a connection has been established.
❏e printer is recognized, but scanning cannot be performed.
“Cannot Scan Even ough a Connection has been Correctly Established (Mac OS)” on page 164
Cannot connect to a Network
e problem could be one of the following issues.
Something is wrong with the network devices for Wi-Fi connection.
Solutions
Turn o the devices you want to connect to the network. Wait for about 10 seconds, and then turn on the
devices in the following order; wireless router, computer or smart device, and then printer. Move the
printer and computer or smart device closer to the wireless router to help with radio wave
communication, and then try to make network settings again.
Solving Problems
>
The Printer Does Not Work as Expected
>
Cannot Start Scanning
161
Devices cannot receive signals from the wireless router because they are too far apart.
Solutions
Aer moving the computer or the smart device and the printer closer to the wireless router, turn o the
wireless router, and then turn it back on.
When changing the wireless router, the settings do not match the new router.
Solutions
Make the connection settings again so that they match the new wireless router.
&“When Replacing the Wireless Router” on page 219
The SSIDs connected from the computer or smart device and computer are dierent.
Solutions
When you are using multiple wireless routers at the same time or the wireless router has multiple SSIDs
and devices are connected to dierent SSIDs, you cannot connect to the wireless router.
Connect the computer or smart device to the same SSID as the printer.
❏Example of connecting to dierent SSIDs
❏Example of connecting to SSIDs with a dierent frequency range
Solving Problems
>
The Printer Does Not Work as Expected
>
Cannot Start Scanning
162
A privacy separator on the wireless router is available.
Solutions
Most wireless routers have a separator function that blocks communication between devices within the
same SSID. If you cannot communicate between the printer and the computer or smart device even if
they are connected to the same network, disable the separator function on the wireless router. See the
manual provided with the wireless router for details.
The IP address is incorrectly assigned.
Solutions
If the IP address assigned to the printer is 169.254.XXX.XXX, and the subnet mask is 255.255.0.0, the IP
address may not be assigned correctly.
Select Settings > General Settings > Network Settings > Advanced on the printer’s control panel, and
then check the IP address and the subnet mask assigned to the printer.
Restart the wireless router or reset the network settings for the printer.
&“Re-setting the Network Connection” on page 219
There is a problem with the network settings on the computer.
Solutions
Try accessing any website from your computer to make sure that your computer's network settings are
correct. If you cannot access any website, there is a problem on the computer.
Check the network connection of the computer. See the documentation provided with the computer for
details.
The printer has been connected by Ethernet using devices that support IEEE802.3az (Energy
Ecient Ethernet).
Solutions
When you connect the printer by Ethernet using devices that support IEEE802.3az (Energy Ecient
Ethernet), the following problems may occur depending on the hub or router that you are using.
❏Connection becomes unstable, the printer is connected and disconnected again and again.
❏Cannot connect to the printer.
❏e communication speed becomes slow.
Follow the steps below to disable IEEE802.3az for the printer and then connect.
1. Remove the Ethernet cable connected to the computer and the printer.
2. When IEEE802.3az for the computer is enabled, disable it.
See the documentation provided with the computer for details.
3. Connect the computer and the printer with an Ethernet cable directly.
4. On the printer, print a network connection report.
“Printing a Network Connection Report” on page 230
5. Check the printer's IP address on the network connection report.
Solving Problems
>
The Printer Does Not Work as Expected
>
Cannot Start Scanning
163
6. On the computer, access Web Cong.
Launch a Web browser, and then enter the printer's IP address.
“Application for Conguring Printer Operations (Web Cong)” on page 249
7. Select Advanced Settings from the list at the top right of the window.
8. Select Network Settings > Wired LAN.
9. Select OFF for IEEE 802.3az.
10. Click Next.
11. Click OK.
12. Remove the Ethernet cable connected to the computer and the printer.
13. If you disabled IEEE802.3az for the computer in step 2, enable it.
14. Connect the Ethernet cables that you removed in step 1 to the computer and the printer.
If the problem still occurs, devices other than the printer may be causing the problem.
The Printer Cannot Connect by USB (Mac OS)
e following causes can be considered.
The USB cable is not plugged into the electrical outlet correctly.
Solutions
Connect the USB cable securely to the printer and the computer.
There is a problem with the USB hub.
Solutions
If you are using a USB hub, try to connect the printer directly to the computer.
There is a problem with the USB cable or the USB inlet.
Solutions
If the USB cable cannot be recognized, change the port, or change the USB cable.
Cannot Scan Even Though a Connection has been Correctly Established (Mac OS)
Scanning at a high resolution over a network.
Solutions
Try scanning at a lower resolution.
Solving Problems
>
The Printer Does Not Work as Expected
>
Cannot Start Scanning
164
Cannot Start Scanning from Smart Device
Make sure the smart device and the printer are connected correctly.
e cause and solution to the problem dier depending on whether or not they are connected.
Check the connection with the smart device
Use Epson Smart Panel to check the connection between the smart device and the printer.
Open the Epson Smart Panel. If you cannot connect to the printer, tap [+] at the top of the screen to reset.
If you are not using Epson Smart Panel, see the link below.
http://epson.sn
Cannot connect to a Network
e problem could be one of the following issues.
Something is wrong with the network devices for Wi-Fi connection.
Solutions
Turn o the devices you want to connect to the network. Wait for about 10 seconds, and then turn on the
devices in the following order; wireless router, computer or smart device, and then printer. Move the
printer and computer or smart device closer to the wireless router to help with radio wave
communication, and then try to make network settings again.
Devices cannot receive signals from the wireless router because they are too far apart.
Solutions
Aer moving the computer or the smart device and the printer closer to the wireless router, turn o the
wireless router, and then turn it back on.
When changing the wireless router, the settings do not match the new router.
Solutions
Make the connection settings again so that they match the new wireless router.
&“When Replacing the Wireless Router” on page 219
Solving Problems
>
The Printer Does Not Work as Expected
>
Cannot Start Scanning
165
The SSIDs connected from the computer or smart device and computer are dierent.
Solutions
When you are using multiple wireless routers at the same time or the wireless router has multiple SSIDs
and devices are connected to dierent SSIDs, you cannot connect to the wireless router.
Connect the computer or smart device to the same SSID as the printer.
❏Example of connecting to dierent SSIDs
❏Example of connecting to SSIDs with a dierent frequency range
A privacy separator on the wireless router is available.
Solutions
Most wireless routers have a separator function that blocks communication between devices within the
same SSID. If you cannot communicate between the printer and the computer or smart device even if
they are connected to the same network, disable the separator function on the wireless router. See the
manual provided with the wireless router for details.
The IP address is incorrectly assigned.
Solutions
If the IP address assigned to the printer is 169.254.XXX.XXX, and the subnet mask is 255.255.0.0, the IP
address may not be assigned correctly.
Solving Problems
>
The Printer Does Not Work as Expected
>
Cannot Start Scanning
166
Select Settings > General Settings > Network Settings > Advanced on the printer’s control panel, and
then check the IP address and the subnet mask assigned to the printer.
Restart the wireless router or reset the network settings for the printer.
&“Re-setting the Network Connection” on page 219
There is a problem with the network settings on the smart device.
Solutions
Try accessing any website from your smart device to make sure that your smart device's network settings
are correct. If you cannot access any website, there is a problem on the smart device.
Check the network connection of the computer. See the documentation provided with the smart device
for details.
Cannot Send or Receive Faxes
Cannot Send or Receive Faxes
e following causes can be considered.
There are some problems in telephone wall jack.
Solutions
Check that the telephone wall jack works by connecting a phone to it and testing it. If you cannot make or
receive calls, contact your telecommunication company.
There are some problems in connecting to the telephone line.
Solutions
Select Settings > General Settings > Fax Settings > Check Fax Connection on the control panel to run
the automatic fax connection check. Try the solutions printed on the report.
Communication error occurs.
Solutions
Select Slow(9,600bps) in Settings > General Settings > Fax Settings > Basic Settings > Fax Speed on
the control panel.
Connected to a DSL phone line without DSL lter.
Solutions
To connect to a DSL phone line, you need to use a DSL modem equipped with a built-in DSL lter, or
install a separate DSL lter to the line. Contact your DSL provider.
“Connecting to DSL or ISDN” on page 284
There are some problems in the DSL lter when you connect to a DSL phone line.
Solutions
If you can not send or receive fax, connect the printer directly to a telephone wall jack to see if the printer
can send a fax. If it works, the problem may be caused by the DSL lter. Contact your DSL provider.
Solving Problems
>
The Printer Does Not Work as Expected
>
Cannot Send or Receive Faxes
167
Cannot Send Faxes
e following causes can be considered.
The connection line is set to PSTN in a facility where a private branch exchange (PBX) is
being used.
Solutions
Select PBX in Settings > General Settings > Fax Settings > Basic Settings > Line Type on the control
panel.
Sending faxes without entering an access code in an environment in which a PBX is
installed.
Solutions
If your phone system requires an external access code to get an outside line, register the access code to the
printer, and enter # (hash) at the beginning of a fax number when sending.
The header information for outgoing faxes is not registered.
Solutions
Select Settings > General Settings > Fax Settings > Basic Settings > Header and set up the header
information. Some fax machines automatically reject incoming faxes that do not include header
information.
Your caller ID is blocked.
Solutions
Contact your telecommunication company to unblock your caller ID. Some phones or fax machines
automatically reject anonymous calls.
The recipient's fax number is wrong.
Solutions
Check that the recipient's number registered in your contacts list or that you entered directly using the
keypad is correct. Or, check with the recipient that the fax number is correct.
The recipient's fax machine is not ready to receive faxes.
Solutions
Ask the recipient if the recipient's fax machine is ready to receive a fax.
The data being sent is too large.
Solutions
You can send faxes at a smaller data size using one of the following methods.
❏When you send the fax in monochrome, enable Direct Send in Fax > Fax Settings > Fax Send
Settings.
“Sending Many Pages of a Monochrome Document (Direct Send)” on page 91
❏Using the connected phone
“Sending Faxes Dialing from the External Phone Device” on page 91
Solving Problems
>
The Printer Does Not Work as Expected
>
Cannot Send or Receive Faxes
168
❏Separating the originals
Cannot Receive Faxes
e following causes can be considered.
Subscribing to a call forwarding service.
Solutions
If you have subscribed to a call forwarding service, the printer may not be able to receive faxes. Contact
the service provider.
The Receive Mode is set to Manual while an external phone device is connected to the
printer.
Solutions
If an external phone device is connected to the printer and is sharing a phone line with the printer, select
Settings >General Settings > Fax Settings > Basic Settings, and then set Receive Mode to Auto.
The available memory of the inbox is not enough.
Solutions
100 received documents have been saved in the inbox in total. Delete the unnecessary documents.
The computer that will save the received faxes is not turned on.
Solutions
When you have made settings to save received faxes to a computer, turn on the computer. e received
fax is deleted once it has been saved to the computer.
The sender's fax number has been registered to the Rejection Number List.
Solutions
Make sure that the sender's number can be deleted from the Rejection Number List before deleting it.
Delete it from Settings > General Settings > Fax Settings > Basic Settings > Rejection Fax > Edit
Blocked Number list. Or disable the Rejection Number List in Settings > General Settings > Fax
Settings > Basic Settings > Rejection Fax > Rejection Fax. Faxes sent from numbers that have not been
registered to this list are blocked when this setting is enabled.
The sender's fax number has not been registered in the contacts list.
Solutions
Register the sender's fax number to contact list. Or disable Unregistered Contacts in Settings > General
Settings > Fax Settings > Basic Settings > Rejection Fax > Rejection Fax. Faxes sent from numbers that
have not been registered to this list are blocked.
The sender has sent the fax without header information.
Solutions
Ask the sender if header information is setup on their fax machine. Or, disable Fax Header Blank in
Settings > General Settings > Fax Settings > Basic Settings > Rejection Fax > Rejection Fax. Faxes that
do not include header information are blocked when this setting is enabled.
Solving Problems
>
The Printer Does Not Work as Expected
>
Cannot Send or Receive Faxes
169
Cannot Send Faxes to a Specic Recipient
The Fax Speed setting registered in the contact list is wrong.
Solutions
Select the recipient from the contact list, and then select Edit > Fax Speed > Slow(9,600bps).
Cannot Send Faxes at a Specied Time
The printer's date and time is wrong.
Solutions
Select Settings > General Settings > Basic Settings > Date/Time Settings, and then set the correct date
and time.
Faxes Are Sent at the Wrong Size
e following causes can be considered.
The originals are not placed correctly.
Solutions
❏Make sure the original is placed correctly against the alignment marks.
❏If the edge of the scanned image is missing, move the original slightly away from the edge of the
scanner glass. You cannot scan the area within approximately 1.5 mm (0.06 in.) from the edge of the
scanner glass.
&“Placing Originals” on page 35
There is dust or dirt on the originals or the scanner glass.
Solutions
Remove any dust or dirt that adheres to the originals, and clean the scanner glass.
&“Cleaning the Scanner Glass” on page 114
Received Faxes Are Not Printed
e following causes can be considered.
An error has occurred in the printer such as a paper jam.
Solutions
Clear the printer error, and then ask the sender to resend the fax.
Printing received faxes is disabled under the current settings.
Solutions
If Save to Computer is set to Yes, change the setting to Ye s and Pr int. Or, disable Save to Inbox and Save
to Computer allows printing to be performed.
Solving Problems
>
The Printer Does Not Work as Expected
>
Cannot Send or Receive Faxes
170
You c a n n d Save to Inbox and Save to Computer in Settings > General Settings > Fax Settings >
Receive Settings > Fax Output Settings.
Cannot Send and Receive Faxes (Windows)
Make sure the computer and the printer are connected correctly. e cause and solution to the problem dier
depending on whether or not they are connected.
Checking the Connection Status
Use Epson Printer Connection Checker to check the connection status for the computer and the printer. You may
be able to solve the problem depending on the results of the check.
1. Double-click the Epson Printer Connection Checker icon on the desktop.
Epson Printer Connection Checker starts.
If there is no icon on the desktop, follow the methods below to start Epson Printer Connection Checker.
❏Windows 10
Click the start button, and then select Epson Soware > Epson Printer Connection Checker.
❏Windows 8.1/Windows 8
Enter the application name in the search charm, and then select the displayed icon.
❏Windows 7
Click the start button, and then select All Programs > Epson Soware > Epson Printer Connection
Checker.
2. Follow the on-screen instructions to check.
Note:
If the printer name is not displayed, install a genuine Epson printer driver.
“Checking if a genuine Epson printer driver is installed - Windows” on page 124
When you have identied the problem, follow the solution displayed on the screen.
When you cannot solve the problem, check the following according to your situation.
❏e printer is not recognized over a network connection
“Cannot connect to a Network” on page 140
❏e printer is not recognized using a USB connection
“e Printer Cannot Connect by USB (Windows)” on page 143
❏e printer is recognized, but printing cannot be performed.
“Cannot Print Even ough a Connection has been Established (Windows)” on page 143
Cannot connect to a Network
e problem could be one of the following issues.
Solving Problems
>
The Printer Does Not Work as Expected
>
Cannot Send or Receive Faxes
171
Something is wrong with the network devices for Wi-Fi connection.
Solutions
Turn o the devices you want to connect to the network. Wait for about 10 seconds, and then turn on the
devices in the following order; wireless router, computer or smart device, and then printer. Move the
printer and computer or smart device closer to the wireless router to help with radio wave
communication, and then try to make network settings again.
Devices cannot receive signals from the wireless router because they are too far apart.
Solutions
Aer moving the computer or the smart device and the printer closer to the wireless router, turn o the
wireless router, and then turn it back on.
When changing the wireless router, the settings do not match the new router.
Solutions
Make the connection settings again so that they match the new wireless router.
&“When Replacing the Wireless Router” on page 219
The SSIDs connected from the computer or smart device and computer are dierent.
Solutions
When you are using multiple wireless routers at the same time or the wireless router has multiple SSIDs
and devices are connected to dierent SSIDs, you cannot connect to the wireless router.
Connect the computer or smart device to the same SSID as the printer.
❏Example of connecting to dierent SSIDs
Solving Problems
>
The Printer Does Not Work as Expected
>
Cannot Send or Receive Faxes
172
❏Example of connecting to SSIDs with a dierent frequency range
A privacy separator on the wireless router is available.
Solutions
Most wireless routers have a separator function that blocks communication between devices within the
same SSID. If you cannot communicate between the printer and the computer or smart device even if
they are connected to the same network, disable the separator function on the wireless router. See the
manual provided with the wireless router for details.
The IP address is incorrectly assigned.
Solutions
If the IP address assigned to the printer is 169.254.XXX.XXX, and the subnet mask is 255.255.0.0, the IP
address may not be assigned correctly.
Select Settings > General Settings > Network Settings > Advanced on the printer’s control panel, and
then check the IP address and the subnet mask assigned to the printer.
Restart the wireless router or reset the network settings for the printer.
&“Re-setting the Network Connection” on page 219
There is a problem with the network settings on the computer.
Solutions
Try accessing any website from your computer to make sure that your computer's network settings are
correct. If you cannot access any website, there is a problem on the computer.
Check the network connection of the computer. See the documentation provided with the computer for
details.
The printer has been connected by Ethernet using devices that support IEEE802.3az (Energy
Ecient Ethernet).
Solutions
When you connect the printer by Ethernet using devices that support IEEE802.3az (Energy Ecient
Ethernet), the following problems may occur depending on the hub or router that you are using.
❏Connection becomes unstable, the printer is connected and disconnected again and again.
❏Cannot connect to the printer.
Solving Problems
>
The Printer Does Not Work as Expected
>
Cannot Send or Receive Faxes
173
❏e communication speed becomes slow.
Follow the steps below to disable IEEE802.3az for the printer and then connect.
1. Remove the Ethernet cable connected to the computer and the printer.
2. When IEEE802.3az for the computer is enabled, disable it.
See the documentation provided with the computer for details.
3. Connect the computer and the printer with an Ethernet cable directly.
4. On the printer, print a network connection report.
“Printing a Network Connection Report” on page 230
5. Check the printer's IP address on the network connection report.
6. On the computer, access Web Cong.
Launch a Web browser, and then enter the printer's IP address.
“Application for Conguring Printer Operations (Web Cong)” on page 249
7. Select Advanced Settings from the list at the top right of the window.
8. Select Network Settings > Wired LAN.
9. Select OFF for IEEE 802.3az.
10. Click Next.
11. Click OK.
12. Remove the Ethernet cable connected to the computer and the printer.
13. If you disabled IEEE802.3az for the computer in step 2, enable it.
14. Connect the Ethernet cables that you removed in step 1 to the computer and the printer.
If the problem still occurs, devices other than the printer may be causing the problem.
The Printer Cannot Connect by USB (Windows)
e following causes can be considered.
The USB cable is not plugged into the electrical outlet correctly.
Solutions
Connect the USB cable securely to the printer and the computer.
There is a problem with the USB hub.
Solutions
If you are using a USB hub, try to connect the printer directly to the computer.
Solving Problems
>
The Printer Does Not Work as Expected
>
Cannot Send or Receive Faxes
174
There is a problem with the USB cable or the USB inlet.
Solutions
If the USB cable cannot be recognized, change the port, or change the USB cable.
Cannot Send or Receive Faxes Even Though a Connection has been Correctly
Established (Windows)
e following causes can be considered.
The software is not installed.
Solutions
Make sure that the PC-FAX driver have been installed on the computer. e PC-FAX driver is installed
with FAX Utility. Follow the steps below to check if it is installed.
Make sure the printer (fax) is displayed in Devices and Printers, Printer, or Printers and Other
Hardware. e printer (fax) is displayed as "EPSON XXXXX (FAX)". If the printer (fax) is not displayed,
uninstall and then re-install the FAX Utility. See the following to access Devices and Printers, Printer, or
Printers and Other Hardware.
❏Windows 10
Click on the start button, and then select Windows System > Control Panel > View devices and
printers in Hardware and Sound.
❏Windows 8.1/Windows 8
Select Desktop > Settings > Control Panel > View devices and printers in Hardware and Sound or
Hardware.
❏Windows 7
Click the start button, and select Control Panel > View devices and printers in Hardware and Sound
or Hardware.
❏Windows Vista
Click the start button, and select Control Panel > Printers in Hardware and Sound.
❏Windows XP
Click the start button, and select Settings > Control Panel > Printers and Other Hardware > Printers
and Faxes.
User authentication failed when a fax is sent from a computer.
Solutions
Set the user name and password in the printer driver. When sending a fax from a computer when the
security function that restrict users from using the printer's fax function is set, user authentication is
performed with the user name and password set in the printer driver.
There are some problems with fax connection and fax settings.
Solutions
Try the resolutions for fax connection and fax settings.
Solving Problems
>
The Printer Does Not Work as Expected
>
Cannot Send or Receive Faxes
175
Cannot Send and Receive Faxes (Mac OS)
Make sure the computer and the printer are connected correctly. e cause and solution to the problem dier
depending on whether or not they are connected.
Checking the Connection Status
Use EPSON Status Monitor to check the connection status for the computer and the printer.
1. Select System Preferences from the Apple menu > Printers & Scanners (or Print & Scan, Print & Fax), and
then select the printer.
2. Click Options & Supplies > Utility > Open Printer Utility.
3. Click EPSON Status Monitor.
When the status of consumables is displayed, a connection has been successfully established between the computer
and the printer.
Check the following if a connection has not been established.
❏e printer is not recognized over a network connection
“Cannot connect to a Network” on page 147
❏e printer is not recognized using a USB connection
“e Printer Cannot Connect by USB (Mac OS)” on page 150
Check the following if a connection has been established.
❏e printer is recognized, but printing cannot be performed.
“Cannot Print Even ough a Connection has been Established (Mac OS)” on page 151
Cannot connect to a Network
e problem could be one of the following issues.
Something is wrong with the network devices for Wi-Fi connection.
Solutions
Turn o the devices you want to connect to the network. Wait for about 10 seconds, and then turn on the
devices in the following order; wireless router, computer or smart device, and then printer. Move the
printer and computer or smart device closer to the wireless router to help with radio wave
communication, and then try to make network settings again.
Solving Problems
>
The Printer Does Not Work as Expected
>
Cannot Send or Receive Faxes
176
Devices cannot receive signals from the wireless router because they are too far apart.
Solutions
Aer moving the computer or the smart device and the printer closer to the wireless router, turn o the
wireless router, and then turn it back on.
When changing the wireless router, the settings do not match the new router.
Solutions
Make the connection settings again so that they match the new wireless router.
&“When Replacing the Wireless Router” on page 219
The SSIDs connected from the computer or smart device and computer are dierent.
Solutions
When you are using multiple wireless routers at the same time or the wireless router has multiple SSIDs
and devices are connected to dierent SSIDs, you cannot connect to the wireless router.
Connect the computer or smart device to the same SSID as the printer.
❏Example of connecting to dierent SSIDs
❏Example of connecting to SSIDs with a dierent frequency range
Solving Problems
>
The Printer Does Not Work as Expected
>
Cannot Send or Receive Faxes
177
A privacy separator on the wireless router is available.
Solutions
Most wireless routers have a separator function that blocks communication between devices within the
same SSID. If you cannot communicate between the printer and the computer or smart device even if
they are connected to the same network, disable the separator function on the wireless router. See the
manual provided with the wireless router for details.
The IP address is incorrectly assigned.
Solutions
If the IP address assigned to the printer is 169.254.XXX.XXX, and the subnet mask is 255.255.0.0, the IP
address may not be assigned correctly.
Select Settings > General Settings > Network Settings > Advanced on the printer’s control panel, and
then check the IP address and the subnet mask assigned to the printer.
Restart the wireless router or reset the network settings for the printer.
&“Re-setting the Network Connection” on page 219
There is a problem with the network settings on the computer.
Solutions
Try accessing any website from your computer to make sure that your computer's network settings are
correct. If you cannot access any website, there is a problem on the computer.
Check the network connection of the computer. See the documentation provided with the computer for
details.
The printer has been connected by Ethernet using devices that support IEEE802.3az (Energy
Ecient Ethernet).
Solutions
When you connect the printer by Ethernet using devices that support IEEE802.3az (Energy Ecient
Ethernet), the following problems may occur depending on the hub or router that you are using.
❏Connection becomes unstable, the printer is connected and disconnected again and again.
❏Cannot connect to the printer.
❏e communication speed becomes slow.
Follow the steps below to disable IEEE802.3az for the printer and then connect.
1. Remove the Ethernet cable connected to the computer and the printer.
2. When IEEE802.3az for the computer is enabled, disable it.
See the documentation provided with the computer for details.
3. Connect the computer and the printer with an Ethernet cable directly.
4. On the printer, print a network connection report.
“Printing a Network Connection Report” on page 230
5. Check the printer's IP address on the network connection report.
Solving Problems
>
The Printer Does Not Work as Expected
>
Cannot Send or Receive Faxes
178
6. On the computer, access Web Cong.
Launch a Web browser, and then enter the printer's IP address.
“Application for Conguring Printer Operations (Web Cong)” on page 249
7. Select Advanced Settings from the list at the top right of the window.
8. Select Network Settings > Wired LAN.
9. Select OFF for IEEE 802.3az.
10. Click Next.
11. Click OK.
12. Remove the Ethernet cable connected to the computer and the printer.
13. If you disabled IEEE802.3az for the computer in step 2, enable it.
14. Connect the Ethernet cables that you removed in step 1 to the computer and the printer.
If the problem still occurs, devices other than the printer may be causing the problem.
The Printer Cannot Connect by USB (Mac OS)
e following causes can be considered.
The USB cable is not plugged into the electrical outlet correctly.
Solutions
Connect the USB cable securely to the printer and the computer.
There is a problem with the USB hub.
Solutions
If you are using a USB hub, try to connect the printer directly to the computer.
There is a problem with the USB cable or the USB inlet.
Solutions
If the USB cable cannot be recognized, change the port, or change the USB cable.
Cannot Send or Receive Even Though a Connection has been Correctly Established
(Mac OS)
e following causes can be considered.
The software is not installed.
Solutions
Make sure that the PC-FAX driver have been installed on the computer. e PC-FAX driver is installed
with FAX Utility. Follow the steps below to check if it is installed.
Solving Problems
>
The Printer Does Not Work as Expected
>
Cannot Send or Receive Faxes
179
Select System Preferences from the Apple menu > Printers & Scanners (or Print & Scan, Print & Fax),
and then make sure the printer (fax) is displayed. e printer (fax) is displayed as "FAX XXXX (USB)" or
"FAX XXXX (IP)". If the printer (fax) is not displayed, click [+] and then register the printer (fax).
PC-FAX driver is paused.
Solutions
Select System Preferences from the Apple menu > Printers & Scanners (or Print & Scan, Print & Fax),
and then double-click the printer (fax). If the printer is paused, click Resume (or Resume Printer).
User authentication failed when a fax is sent from a computer.
Solutions
Set the user name and password in the printer driver. When sending a fax from a computer when the
security function that restrict users from using the printer's fax function is set, user authentication is
performed with the user name and password set in the printer driver.
There are some problems with fax connection and fax settings.
Solutions
Try the resolutions for fax connection and fax settings.
Cannot Operate the Printer as Expected
Operations are Slow
Printing Is Too Slow
e following causes can be considered.
Unnecessary applications are running.
Solutions
Close any unnecessary applications on your computer or smart device.
The print quality is set to high.
Solutions
Lower the quality setting.
Bidirectional printing is disabled.
Solutions
Enable the bidirectional (or high speed) setting. When this setting is enabled, the print head prints while
moving in both directions, and the printing speed increases.
❏Windows
Select Bidirectional Printing on the printer driver's More Options tab.
Solving Problems
>
The Printer Does Not Work as Expected
>
Cannot Operate the Printer as Expected
180
❏Mac OS
Select System Preferences from the Apple menu > Printers & Scanners (or Print & Scan, Print &
Fax), and then select the printer. Click Options & Supplies > Options (or Driver). Select On as the
Bidirectional Printing setting.
Quiet Mode is enabled.
Solutions
Disable Quiet Mode. e printing speed slows down when the printer is running in Quiet Mode.
❏Control panel
Select on the home screen, and then select O.
❏Windows
Select O as the Quiet Mode setting on the printer driver's Main tab.
❏Mac OS
Select System Preferences from the Apple menu > Printers & Scanners (or Print & Scan, Print &
Fax), and then select the printer. Click Options & Supplies > Options (or Driver). Select O as the
Quiet Mode setting.
Printing Slows Down Dramatically During Continuous Printing
The function that prevents the printer mechanism from overheating and being damaged is
operating.
Solutions
You can continue printing. To return to normal printing speed, leave the printer idle for at least 30
minutes. Printing speed does not return to normal if the power is o.
Scanning Speed Is Slow
Scanning at a high resolution.
Solutions
Try scanning at a lower resolution.
LCD Screen Gets Dark
The printer is in sleep mode.
Solutions
Tap anywhere on the LCD screen to return it to its former state.
Solving Problems
>
The Printer Does Not Work as Expected
>
Cannot Operate the Printer as Expected
181
Operation Sounds Are Loud
Quiet Mode is disabled on the printer.
Solutions
If operations sounds are too loud, enable Quiet Mode. Enabling this feature may reduce printing speed.
❏Control panel
Select on the home screen, and then select On.
❏Windows
Select On as the Quiet Mode on the printer driver's Main tab.
❏Mac OS
Select System Preferences from the Apple menu > Printers & Scanners (or Print & Scan, Print &
Fax), and then select the printer. Click Options & Supplies > Options (or Driver). Select On as the
Quiet Mode setting.
The Date and Time Are Incorrect
Error occurred in power supply.
Solutions
Aer a power failure caused by a lightning strike or if the power is le o for a long time, the clock may
show the wrong time. Set the date and the time correctly in Settings > General Settings > Basic Settings
> Date/Time Settings on the control panel.
The Root Certicate Needs to be Updated
The root certicate has expired.
Solutions
Run Web Cong, and then update the root certicate.
Cannot Cancel Printing from a Computer Running Mac OS X v10.6.8
There is a problem with your AirPrint setup.
Solutions
Run Web Cong, and then select Port9100 as the Top Priority Protocol setting in AirPrint Setup. Select
System Preferences from the Apple menu > Printers & Scanners (or Print & Scan, Print & Fax), remove
the printer, and then add the printer again.
&“Application for Conguring Printer Operations (Web Cong)” on page 249
Solving Problems
>
The Printer Does Not Work as Expected
>
Cannot Operate the Printer as Expected
182
Sender's Fax Number Not Displayed
The sender's fax number is not set to the sender's machine.
Solutions
e sender may not have set the fax number. Contact the sender.
Sender's Fax Number Displayed on Received Faxes is Wrong
The sender's fax number set to the sender's machine is wrong.
Solutions
e sender may have set the fax number incorrectly. Contact the sender.
Cannot Make Calls on the Connected Telephone
The phone cable is not connected correctly.
Solutions
Connect the telephone to the EXT. port on the printer, and pick up the receiver. If you cannot hear a dial
tone through the receiver, connect the phone cable correctly.
Answering Machine Cannot Answer Voice Calls
The printer's Rings to Answer setting is set to less than the number of rings for your
answering machine.
Solutions
Select Slow(9,600bps) in Settings > General Settings > Fax Settings > Basic Settings > Rings to
Answer, and then set to a number higher than the number of rings for your answering machine.
A Lot of Junk Faxes Have Been Received
The printer's feature to block junk faxes has not been set up.
Solutions
Make Rejection Fax settings in Settings > General Settings > Fax Settings > Basic Settings.
“Making Settings for Blocking Junk Faxes” on page 290
A Message is Displayed on the LCD Screen
If an error message is displayed on the LCD screen, follow the on-screen instructions or the solutions below to
solve the problem.
Solving Problems
>
A Message is Displayed on the LCD Screen
183
Error Messages Solutions
Printer Error
Turn on the printer again. See your
documentation for more details.
Remove any paper or protective material in the printer. If the error
message is still displayed, contact Epson support.
Paper out in XX. Load paper, and then insert the paper cassette all the way.
Paper Setup Auto Display is set to O. Some
features may not be available. For details, see
your documentation.
If Paper Setup Auto Display is disabled, you cannot use AirPrint.
No dial tone is detected. This problem might be resolved by selecting Settings > General
Settings > Fax Settings > Basic Settings > Line Type and then
selecting PBX. If your phone system requires an external access code to
get an outside line, set the access code after selecting PBX. Use # (hash)
instead of the actual access code when entering an outside fax number.
This makes connection more secure.
If the error message is still displayed, set the Dial Tone Detection
settings to disabled. However, disabling this feature may drop the rst
digit of a fax number and send the fax to the wrong number.
The combination of the IP address and the
subnet mask is invalid. See your documentation
for more details.
Enter the correct IP address or default gateway. Contact the person who
setup the network for assistance.
To use cloud services, update the root certicate
from the Epson Web Cong utility.
Run Web Cong, and then update the root certicate.
Check that the printer driver is installed on the
computer and that the port settings for the
printer are correct.
Make sure the printer port is selected correctly in Property > Port from
the Printer menu as follows.
Select "USBXXX" for a USB connection, or "EpsonNet Print Port" for a
network connection.
Check that the printer driver is installed on the
computer and that the USB port settings for the
printer are correct.
Recovery Mode The printer has started in recovery mode because the rmware update
failed. Follow the steps below to try to update the rmware again.
1. Connect the computer and the printer with a USB cable. (During
recovery mode, you cannot update the rmware over a network
connection.)
2. Visit your local Epson website for further instructions.
Paper Gets Jammed
Check the error displayed on the control panel and follow the instructions to remove the jammed paper including
any torn pieces. Next, clear the error.
c
Important:
❏Remove the jammed paper carefully. Removing the paper vigorously may cause damage to the printer.
❏When removing jammed paper, avoid tilting the printer, placing it vertically, or turning it upside down;
otherwise ink may leak.
Solving Problems
>
Paper Gets Jammed
184
Removing Jammed Paper
!
Caution:
Never touch the buttons on the control panel while your hand is inside the printer. If the printer starts operating, it
could cause an injury. Be careful not to touch the protruding parts to avoid injury.
1. Remove the jammed paper.
2. Remove the rear cover.
3. Remove the jammed paper.
Solving Problems
>
Paper Gets Jammed
>
Removing Jammed Paper
185
8. Remove the jammed paper.
c
Important:
Do not touch the parts inside the printer. Doing so may cause a malfunction.
9. Raise the output switch lever.
10. Close the front cover.
11. Open the printer cover, and then use the knob to fasten it to the top.
Solving Problems
>
Paper Gets Jammed
>
Removing Jammed Paper
187
12. Remove the jammed paper.
c
Important:
Do not touch the white at cable, translucent lm, and ink tubes inside the printer. Doing so may cause a
malfunction. If you touch the translucent lm, make sure you clean it.
13. Close the printer cover until it clicks.
Solving Problems
>
Paper Gets Jammed
>
Removing Jammed Paper
188
5. Lower the ADF input tray.
6. Close the ADF cover until it clicks.
Preventing Paper Jams
Check the following if paper jams occur frequently.
❏Place the printer on a at surface and operate in the recommended environmental conditions.
“Environmental Specications” on page 271
❏Use the paper supported by this printer.
“Available Paper and Capacities” on page 239
❏Follow paper handling precautions.
“Paper Handling Precautions” on page 29
❏Load paper in the correct direction, and slide the edge guide against the edge of the paper.
“Loading Paper” on page 31
Solving Problems
>
Paper Gets Jammed
>
Preventing Paper Jams
191
❏Do not load more than the maximum number of sheets specied for paper.
❏Load one sheet of paper at a time if you have loaded several sheets of paper.
❏Make sure the paper size and paper type settings match the actual paper size and paper type loaded in the
printer.
“List of Paper Type” on page 30
❏Clean the roller inside the printer.
“Cleaning the Paper Path for Paper Feeding Problems” on page 109
It is Time to Rell the Ink
Ink Bottle Handling Precautions
Read the following instructions before relling ink.
Storing precautions for ink
❏Keep the ink bottles out of direct sunlight.
❏Do not store the ink bottles in high or freezing temperatures.
❏Epson recommends using the ink bottle before the date printed on the package.
❏When storing or transporting an ink bottle, do not tilt the bottle and do not subject it to impacts or temperature
changes. Otherwise, ink may leak even if the cap on the ink bottle is tightened securely. Be sure to keep the ink
bottle upright when tightening the cap, and take precautions to prevent ink from leaking when transporting the
bottle, for example, putting the bottle in a bag.
❏Aer bringing an ink bottle inside from a cold storage site, allow it to warm up at room temperature for at least
three hours before using it.
❏Do not open the ink bottle package until you are ready to ll the ink tank. e ink bottle is vacuum packed to
maintain its reliability. If you leave an ink bottle unpacked for a long time before using it, normal printing may
not be possible.
❏Once you open an ink bottle, we recommend using it as soon as possible.
Handling precautions for relling ink
❏To ensure you receive premium print quality and to help protect your print head, a variable ink safety reserve
remains in the ink tank when your printer indicates to rell ink. e yields quoted for you do not include this
reserve.
❏For optimum print results do not maintain low ink levels for extended periods of time.
❏Use ink bottles with the correct part code for this printer.
❏e ink for this printer must be handled carefully. Ink may splatter when the ink tanks are being lled or relled
with ink. If ink gets on your clothes or belongings, it may not come o.
❏Do not shake too vigorously or squeeze the ink bottles.
❏Prolonged use of the printer when the ink level is below the lower line could damage the printer. Fill the ink
tank to the upper line while the printer is not operating. To display the correct ink level estimates, reset the ink
level aer lling the tank.
❏To obtain optimum printing results, rell the ink tanks to the upper line at least once every year.
Solving Problems
>
It is Time to Rell the Ink
>
Ink Bottle Handling Precautions
192
Ink consumption
❏To maintain optimum print head performance, some ink is consumed from all ink tanks during maintenance
operations such as print head cleaning. Ink may also be consumed when you turn the printer on.
❏When printing in monochrome or grayscale, color inks instead of black ink may be used depending on the
paper type or print quality settings. is is because a mixture of color inks is used to create black.
❏e ink in the ink bottles supplied with your printer is partly used during initial setup. In order to produce high
quality printouts, the print head in your printer will be fully charged with ink. is one-o process consumes a
quantity of ink and therefore these bottles may print fewer pages compared to subsequent ink bottles.
❏Quoted yields may vary depending on the images that you are printing, the paper type that you are using, the
frequency of your prints and environmental conditions such as temperature.
❏Visually check ink levels in the actual ink tanks. Prolonged use of the printer when the ink is expended could
damage the printer. Epson recommends lling the ink tank to the upper line when the printer is not operating
to reset the ink level.
Relling the Ink Tank
1. Select Maintenance on the printer's control panel.
2. Select Fill Ink.
3. Read all of the usage precautions for lling ink on the screen, and then proceed to the next screen.
4. Open the ink tank cover.
5. Open the ink tank cap.
Solving Problems
>
It is Time to Rell the Ink
>
Relling the Ink Tank
193
c
Important:
Make sure that the color of the ink tank matches the ink color that you want to rell.
6. While holding the ink bottle upright, turn the cap slowly to remove it.
c
Important:
❏Epson recommends the use of genuine Epson ink bottles.
❏Be careful not to spill any ink.
7. Check the upper line (a) in the ink tank.
8. Align the top of the ink bottle with the lling port, and then insert it straight into the port to ll ink until it
stops automatically at the upper line.
When you insert the ink bottle into the lling port for the correct color, ink starts pouring and the ow stops
automatically when the ink reaches the upper line.
Solving Problems
>
It is Time to Rell the Ink
>
Relling the Ink Tank
194
If the ink does not start owing into the tank, remove the ink bottle and reinsert it. However, do not remove
and reinsert the ink bottle when the ink has reached the upper line; otherwise ink may leak.
9. When you have nished relling the ink, remove the ink bottle, and then close the ink tank cap securely.
c
Important:
Do not leave the ink bottle inserted; otherwise the bottle may be damaged or ink may leak.
Solving Problems
>
It is Time to Rell the Ink
>
Relling the Ink Tank
195
Note:
If any ink remains in the ink bottle, tighten the cap and store the bottle upright for later use.
10. Close the ink tank cover rmly.
11. Follow the on-screen instructions to set the ink level of the color of the ink you relled.
c
Important:
Even if you do not rell ink up to the upper line on the ink tank, you can continue using the printer. To keep your
printer operating at its best, however, ll ink tank up to the upper line and reset the ink level immediately.
Related Information
&“Ink Bottle Codes” on page 242
&“Ink Bottle Handling Precautions” on page 192
&“Cleaning Spilled ink” on page 121
It is Time to Replace the Maintenance Box
Maintenance Box Handling Precautions
Read the following instructions before replacing the maintenance box.
❏Do not touch the green chip on the side of the maintenance box. Doing so may prevent normal operation and
printing.
Solving Problems
>
It is Time to Replace the Maintenance Box
>
Maintenance Box Handling Precautions
196
❏Do not drop the maintenance box or subject it to strong shocks.
❏Do not replace the maintenance box during printing; otherwise, ink may leak.
❏Do not remove the maintenance box and its cover except when replacing the maintenance box; otherwise ink
may leak.
❏When the cover cannot be reattached, the maintenance box may not be installed correctly. Remove the
maintenance box, and re-install it.
❏Do not tilt the used maintenance box until aer it is sealed in the plastic bag; otherwise ink may leak.
❏Do not touch the openings in the maintenance box as you may get smeared with ink.
❏Do not reuse a maintenance box which has been removed and le detached for a long period. Ink inside the box
will have solidied and no more ink can be absorbed.
❏Keep the maintenance box out of direct sunlight.
❏Do not store the maintenance box in high or freezing temperatures.
Replacing a Maintenance Box
In some print cycles a very small amount of surplus ink may be collected in the maintenance box. To prevent ink
leakage from the maintenance box, the printer is designed to stop printing when the absorbing capacity of the
maintenance box has reached its limit. Whether and how oen this is required will vary according to the number
of pages you print, the type of material that you print and the number of cleaning cycles that the printer performs.
When a message is displayed prompting you to replace the maintenance box, refer to the animations displayed on
the control panel. e need for replacement of the box does not mean that your printer has ceased to operate in
accordance with its specications. e Epson warranty does not cover the cost of this replacement. It is a user-
serviceable part.
Note:
❏When the maintenance box is full, you cannot print and clean the print head until it is replaced to avoid ink leakage.
However, you can perform operations that do not use ink such as scanning.
Related Information
&“Maintenance Box Code” on page 243
&“Maintenance Box Handling Precautions” on page 196
Solving Problems
>
It is Time to Replace the Maintenance Box
>
Replacing a Maintenance Box
197
Printing, Copying, Scanning, and Faxing Quality is
Poor
Print Quality is Poor
Color Missing, Banding, or Unexpected Colors Appear in Printout
The print head nozzles may be clogged.
Solutions
❏Perform a nozzle check to see if the print head nozzles are clogged. Perform a nozzle check, and then
clean the print head if any of the print head nozzles are clogged. If you have not used the printer for a
long time, the print head nozzles may be clogged and ink drops may not be discharged.
❏If you printed when the ink levels were too low to be seen in the ink tank windows, rell the ink tanks
to the upper lines and then use the Power Cleaning utility to replace the ink inside the ink tubes. Aer
you use the utility, perform a nozzle check to see if print quality has improved.
&“Checking and Cleaning the Print Head” on page 111
&“Running Power Cleaning” on page 112
Colored Banding Appears at Intervals of Approximately 1.1 cm or 3.3 cm
e following causes can be considered.
The paper type setting does not match the paper loaded.
Solutions
Select the appropriate paper type setting for the type of paper loaded in the printer.
&“List of Paper Type” on page 30
Solving Problems
>
Printing, Copying, Scanning, and Faxing Quality is Poor
>
Print Quality is Poor
198
The print quality is set to low.
Solutions
When printing on plain paper, print using a higher quality setting.
❏Windows
Select High from Quality on the printer driver's Main tab.
❏Mac OS
Select Fine as Print Quality from the print dialog's Print Settings menu.
The print head position is out of alignment.
Solutions
Select the Maintenance > Print Head Alignment > Horizontal Alignment menu on the control panel to
align the print head.
Blurry Prints, Vertical Banding, or Misalignment
e following causes can be considered.
The print head position is out of alignment.
Solutions
Select the Maintenance > Print Head Alignment > Vertical Alignment menu on the control panel to
align the print head.
The bidirectional printing setting is enabled.
Solutions
If print quality does not improve even aer aligning the print head, disable the bidirectional setting.
During bidirectional (or high speed) printing, the print head prints while moving in both directions, and
vertical lines may be misaligned. Disabling this setting may slow down printing speed but improve print
quality.
❏Windows
Clear Bidirectional Printing on the printer driver’s More Options tab.
❏Mac OS
Select System Preferences from the Apple menu > Printers & Scanners (or Print & Scan, Print &
Fax), and then select the printer. Click Options & Supplies > Options (or Driver). Select O as the
Bidirectional Printing setting.
Solving Problems
>
Printing, Copying, Scanning, and Faxing Quality is Poor
>
Print Quality is Poor
199
Printout Comes Out as a Blank Sheet
The print head nozzles may be clogged.
Solutions
Perform the nozzle check, and then try Power Cleaning if the print head nozzles are clogged.
&“Running Power Cleaning” on page 112
The print settings and the paper size loaded in the printer are dierent.
Solutions
Change the print settings according to the paper size loaded in the printer. Load paper in the printer that
matches the print settings.
Multiple sheets of paper are fed into the printer at the same time.
Solutions
See the following to prevent multiple sheets of paper being fed into the printer at the same time.
&“Several Sheets of Paper are Fed at a Time” on page 136
Paper Is Smeared or Scued
e following causes can be considered.
Paper is loaded incorrectly.
Solutions
When horizontal banding (perpendicular to the printing direction) appears, or the top or bottom of the
paper is smeared, load paper in the correct direction and slide the edge guides to the edges of the paper.
&“Loading Paper” on page 31
Solving Problems
>
Printing, Copying, Scanning, and Faxing Quality is Poor
>
Print Quality is Poor
200
The paper path is smeared.
Solutions
When vertical banding (horizontal to the printing direction) appears, or the paper is smeared, clean the
paper path.
&“Cleaning the Paper Path for Ink Smears” on page 114
The paper is curled.
Solutions
Place the paper on a at surface to check if it is curled. If it is, atten it.
The print head is rubbing the surface of the paper.
Solutions
When printing on thick paper, the print head is close to the printing surface and the paper may be
scued. In this case, enable the reduce scu setting. If you enable this setting, print quality may decline or
printing may slow down.
Windows
Click Extended Settings on the printer driver's Maintenance tab, and then select Short Grain Paper.
When printing using automatic 2-sided printing, the print density is too high and the drying
time is too short.
Solutions
When using the automatic 2-sided printing feature and printing high density data such as images and
graphs, set the print density to lower and the drying time to longer.
&“Printing on 2-Sides” on page 40
&“Printing on 2-Sides” on page 40
Printed Photos are Sticky
The print was made on the wrong side of the photo paper.
Solutions
Make sure you are printing on the printable side. When printing on the wrong side of the photo paper,
you need to clean the paper path.
&“Cleaning the Paper Path for Ink Smears” on page 114
Solving Problems
>
Printing, Copying, Scanning, and Faxing Quality is Poor
>
Print Quality is Poor
201
Images or Photos are Printed in Unexpected Colors
e following causes can be considered.
The print head nozzles may be clogged.
Solutions
Perform a nozzle check to see if the print head nozzles are clogged. Perform a nozzle check, and then
clean the print head if any of the print head nozzles are clogged. If you have not used the printer for a
long time, the print head nozzles may be clogged and ink drops may not be discharged.
Color correction has been applied.
Solutions
When printing from the Windows printer driver, the Epson auto photo adjustment setting is applied by
default depending on the paper type. Try change the setting.
On the More Options tab, select Custom in Color Correction, and then click Advanced. Change the
Scene Correction setting from Automatic to any other option. If changing the setting does not work, use
any color correction method other than PhotoEnhance in Color Management.
&“Adjusting the Print Color” on page 53
The Position, Size, or Margins of the Printout Are Incorrect
e following causes can be considered.
The paper is loaded incorrectly.
Solutions
Load paper in the correct direction, and slide the edge guide against the edge of the paper.
&“Loading Paper” on page 31
The size of the paper is set incorrectly.
Solutions
Select the appropriate paper size setting.
Solving Problems
>
Printing, Copying, Scanning, and Faxing Quality is Poor
>
Print Quality is Poor
202
The margin setting in the application software is not within the print area.
Solutions
Adjust the margin setting in the application so that it falls within the printable area.
&“Printable Area” on page 265
Printed Characters Are Incorrect or Garbled
e following causes can be considered.
The USB cable is not connected correctly.
Solutions
Connect the USB cable securely to the printer and the computer.
There is a job waiting to be printed.
Solutions
Cancel any paused print jobs.
The computer has been manually put into the Hibernate mode or the Sleep mode while
printing.
Solutions
Do not put the computer manually into the Hibernate mode or the Sleep mode while printing. Pages of
garbled text may be printed next time you start the computer.
You are using the printer driver for a dierent printer.
Solutions
Make sure that the printer driver you are using is for this printer. Check the printer name on the top of
the printer driver window.
The Printed Image Is Inverted
Solving Problems
>
Printing, Copying, Scanning, and Faxing Quality is Poor
>
Print Quality is Poor
203
The image is set to invert horizontally in the print settings.
Solutions
Clear any mirror image settings in the printer driver or the application.
❏Windows
Clear Mirror Image on the printer driver’s More Options tab.
❏Mac OS
Clear Mirror Image from the print dialog's Print Settings menu.
Mosaic-Like Patterns in the Prints
Images or photos with a low resolution were printed.
Solutions
When printing images or photos, print using high-resolution data. Images on web sites are oen low
resolution although they look good enough on the display, and so print quality may decline.
Copy Quality is Poor
Color Missing, Banding, or Unexpected Colors Appear in Copies
The print head nozzles may be clogged.
Solutions
❏Perform a nozzle check to see if the print head nozzles are clogged. Perform a nozzle check, and then
clean the print head if any of the print head nozzles are clogged. If you have not used the printer for a
long time, the print head nozzles may be clogged and ink drops may not be discharged.
❏If you printed when the ink levels were too low to be seen in the ink tank windows, rell the ink tanks
to the upper lines and then use the Power Cleaning utility to replace the ink inside the ink tubes. Aer
you use the utility, perform a nozzle check to see if print quality has improved.
&“Checking and Cleaning the Print Head” on page 111
&“Running Power Cleaning” on page 112
Solving Problems
>
Printing, Copying, Scanning, and Faxing Quality is Poor
>
Copy Quality is Poor
204
Colored Banding Appears at Intervals of Approximately 1.1 cm or 3.3 cm
e following causes can be considered.
The paper type setting does not match the paper loaded.
Solutions
Select the appropriate paper type setting for the type of paper loaded in the printer.
&“List of Paper Type” on page 30
The print quality is set to low.
Solutions
When printing on plain paper, print using a higher quality setting.
Select Best in Quality.
The print head position is out of alignment.
Solutions
Select the Maintenance > Print Head Alignment > Horizontal Alignment menu on the control panel to
align the print head.
Blurry Copies, Vertical Banding, or Misalignment
e following causes can be considered.
The print head position is out of alignment.
Solutions
Select the Maintenance > Print Head Alignment > Vertical Alignment menu on the control panel to
align the print head.
Solving Problems
>
Printing, Copying, Scanning, and Faxing Quality is Poor
>
Copy Quality is Poor
205
Printout Comes Out as a Blank Sheet
The print head nozzles may be clogged.
Solutions
Perform the nozzle check, and then try Power Cleaning if the print head nozzles are clogged.
&“Running Power Cleaning” on page 112
The print settings and the paper size loaded in the printer are dierent.
Solutions
Change the print settings according to the paper size loaded in the paper cassette. Load paper in the
paper cassette that matches the print settings.
Multiple sheets of paper are fed into the printer at the same time.
Solutions
See the following to prevent multiple sheets of paper being fed into the printer at the same time.
&“Several Sheets of Paper are Fed at a Time” on page 136
Paper Is Smeared or Scued
e following causes can be considered.
Paper is loaded incorrectly.
Solutions
When horizontal banding (perpendicular to the printing direction) appears, or the top or bottom of the
paper is smeared, load paper in the correct direction and slide the edge guides to the edges of the paper.
&“Loading Paper” on page 31
Solving Problems
>
Printing, Copying, Scanning, and Faxing Quality is Poor
>
Copy Quality is Poor
206
The paper path is smeared.
Solutions
When vertical banding (horizontal to the printing direction) appears, or the paper is smeared, clean the
paper path.
&“Cleaning the Paper Path for Ink Smears” on page 114
The paper is curled.
Solutions
Place the paper on a at surface to check if it is curled. If it is, atten it.
Copied Photos are Sticky
The copy was made on the wrong side of the photo paper.
Solutions
Make sure you are copying on the printable side. If you have accidentally copied on the wrong side of the
photo paper, you need to clean the paper path.
&“Loading Paper” on page 31
&“Cleaning the Paper Path for Ink Smears” on page 114
The Position, Size, or Margins of the Copies are Incorrect
e following causes can be considered.
The paper is loaded incorrectly.
Solutions
Load paper in the correct direction, and slide the edge guide against the edge of the paper.
&“Loading Paper” on page 31
Solving Problems
>
Printing, Copying, Scanning, and Faxing Quality is Poor
>
Copy Quality is Poor
207
The size of the paper is set incorrectly.
Solutions
Select the appropriate paper size setting.
The originals are not placed correctly.
Solutions
❏Make sure the original is placed correctly against the alignment marks.
❏If the edge of the scanned image is missing, move the original slightly away from the edge of the
scanner glass. You cannot scan the area within approximately 1.5 mm (0.06 in.) from the edge of the
scanner glass.
&“Placing Originals” on page 35
Uneven Colors, Smears, Dots, or Straight Lines Appear in the Copied Image
e following causes can be considered.
The paper path is dirty.
Solutions
Load and eject paper without printing to clean the paper path.
&“Cleaning the Paper Path for Ink Smears” on page 114
There is dust or dirt on the originals or the scanner glass.
Solutions
Remove any dust or dirt that adheres to the originals, and clean the scanner glass.
&“Cleaning the Scanner Glass” on page 114
There is dust or dirt on the ADF or originals.
Solutions
Clean the ADF, and remove any dust or dirt that adheres to the originals.
&“Cleaning the ADF” on page 115
The original was pressed with too much force.
Solutions
If you press with too much force, blurring, smudges, and spots may occur.
Solving Problems
>
Printing, Copying, Scanning, and Faxing Quality is Poor
>
Copy Quality is Poor
208
Do not press with too much force on the original or the document cover.
&“Placing Originals” on page 35
The copy density setting is too high.
Solutions
Lower the copy density setting.
&“Basic Menu Options for Copying” on page 72
Moiré (Cross-Hatch) Patterns Appear in the Copied Image
If the original is a printed document such as a magazine or a catalog, a dotted moiré pattern
appears.
Solutions
Change the reduce and enlarge setting. If a moiré pattern still appears, place the original at a slightly
dierent angle.
&“Advanced Menu Options for Copying” on page 73
An Image of the Reverse Side of the Original Appears in the Copied Image
e following causes can be considered.
When scanning thin originals, images on the back may be scanned at the same time.
Solutions
Place the original on the scanner glass and then place a piece of black paper over it.
&“Placing Originals” on page 35
The copy density setting is too high.
Solutions
Lower the copy density setting.
&“Basic Menu Options for Copying” on page 72
Solving Problems
>
Printing, Copying, Scanning, and Faxing Quality is Poor
>
Copy Quality is Poor
209
The Text or Image Copied from the ADF is Squeezed or Stretched
Some originals may not be scanned properly from the ADF.
Solutions
Place originals on the scanner glass.
Select , and then select How To > Place Originals > Scanner Glass. Select Finish to close the
animation screen.
Scanned Image Problems
Uneven Colors, Dirt, Spots, and so on Appear when Scanning from the Scanner
Glass
There is dust or dirt on the originals or the scanner glass.
Solutions
Remove any dust or dirt that adheres to the originals, and clean the scanner glass.
&“Cleaning the Scanner Glass” on page 114
The original was pressed with too much force.
Solutions
If you press with too much force, blurring, smudges, and spots may occur.
Do not press with too much force on the original or the document cover.
&“Placing Originals” on page 35
Solving Problems
>
Printing, Copying, Scanning, and Faxing Quality is Poor
>
Scanned Image Problems
210
Straight Lines Appear when Scanning from ADF
There is dust or dirt on the ADF or originals.
Solutions
Clean the ADF, and remove any dust or dirt that adheres to the originals.
&“Cleaning the ADF” on page 115
Oset Appears in the Background of Scanned Images
When scanning thin originals, images on the back may be scanned at the same time.
Solutions
When scanning from the scanner glass, place black paper or a desk pad over the original.
&“Placing Originals” on page 35
Cannot Scan the Correct Area on the Scanner Glass
The originals are not placed correctly.
Solutions
❏Make sure the original is placed correctly against the alignment marks.
❏If the edge of the scanned image is missing, move the original slightly away from the edge of the
scanner glass. You cannot scan the area within approximately 1.5 mm (0.06 in.) from the edge of the
scanner glass.
&“Placing Originals” on page 35
Solving Problems
>
Printing, Copying, Scanning, and Faxing Quality is Poor
>
Scanned Image Problems
211
There is dust or dirt on the scanner glass.
Solutions
When scanning from the control panel and selecting auto scan area cropping function, remove any trash
or dirt from the scanner glass and document cover. If there is any trash or dirt around the original, the
scanning range expands to include it.
Cannot Solve Problems in the Scanned Image
Check the following if you have tried all of the solutions and have not solved the problem.
There are problems with the scanning software settings.
Solutions
Use Epson Scan 2 Utility to initialize the settings for the scanner soware.
Note:
Epson Scan 2 Utility is an application supplied with the scanner soware.
1. Start the Epson Scan 2 Utility.
❏Windows 10
Click the start button, and then select EPSON > Epson Scan 2 Utility.
❏Windows 8.1/Windows 8
Enter the application name in the search charm, and then select the displayed icon.
❏Windows 7/Windows Vista/Windows XP
Click the start button, and then select All Programs or Programs > EPSON > Epson Scan 2 >
Epson Scan 2 Utility.
❏Mac OS
Select Go > Applications > Epson Soware > Epson Scan 2 Utility.
2. Select the Other tab.
3. Click Reset.
If initialization does not solve the problem, uninstall and re-install the scanner soware.
&“Installing or Uninstalling Applications Separately” on page 123
The Text or Image Scanned from the ADF is Squeezed or Stretched
Solving Problems
>
Printing, Copying, Scanning, and Faxing Quality is Poor
>
Scanned Image Problems
212
Some originals may not be scanned properly from the ADF.
Place originals on the scanner glass.
Select , and then select How To > Place Originals > Scanner Glass. Select Finish to close the animation screen.
The Quality of the Sent Fax is Poor
Quality of the Sent Fax is Poor
e following causes can be considered.
There is dust or dirt on the originals or the scanner glass.
Solutions
Remove any dust or dirt that adheres to the originals, and clean the scanner glass.
&“Cleaning the Scanner Glass” on page 114
The original was pressed with too much force.
Solutions
If you press with too much force, blurring, smudges, and spots may occur.
Do not press with too much force on the original or the document cover.
&“Placing Originals” on page 35
Straight Lines Appear when Sending Faxes from the ADF
e following causes can be considered.
There is dust or dirt on the ADF or originals.
Solutions
Clean the ADF, and remove any dust or dirt that adheres to the originals.
&“Cleaning the ADF” on page 115
Solving Problems
>
Printing, Copying, Scanning, and Faxing Quality is Poor
>
The Quality of the Sent Fax is Poor
213
The Image Quality of the Sent Fax is Poor
e following causes can be considered.
The resolution is set to low.
Solutions
If you do not know the performance of the sender’s fax machine, set the following before sending a fax.
❏Select Fax > Fax Settings and then make the Resolution setting to set the highest quality image.
❏Select Fax > Fax Settings and then enable Direct Send.
Note that if you set Resolution to Photo but you send the fax without enabling Direct Send, the fax
may be sent at a lower resolution.
ECM setting is disabled.
Solutions
Select Settings > General Settings > Fax Settings > Basic Settings and enable the ECM setting on the
control panel. is may clear errors that occur due to connection problems. Note that the speed of
sending and receiving faxes may be slower than when ECM is disabled.
An Image of the Reverse Side of the Original Appears in the Sent Fax
e following causes can be considered.
When scanning thin originals, images on the back may be scanned at the same time.
Solutions
Place the original on the scanner glass and then place a piece of black paper over it.
&“Placing Originals” on page 35
The density setting is high when sending faxes.
Solutions
Select Fax > Fax Settings > Scan Settings > Density, and then lower the setting.
Solving Problems
>
Printing, Copying, Scanning, and Faxing Quality is Poor
>
The Quality of the Sent Fax is Poor
214
Received Fax Quality is Poor
The Image Quality of Received Faxes is Poor
e following causes can be considered.
ECM setting is disabled.
Solutions
Select Settings > General Settings > Fax Settings > Basic Settings and enable the ECM setting on the
control panel. is may clear errors that occur due to connection problems. Note that the speed of
sending and receiving faxes may be slower than when ECM is disabled.
The image quality setting is low on the sender's fax machine.
Solutions
Ask the sender to send faxes at a higher quality.
Cannot Solve Problem
If you cannot solve the problem aer trying all of the solutions, contact Epson support.
If you cannot solve printing or copying problems, see the following related information.
Related Information
&“Cannot Solve Printing or Copying Problems” on page 215
Cannot Solve Printing or Copying Problems
Try the following problems in order starting at the top until you solve the problem.
❏Make sure you match the paper type loaded in the printer and the paper type set on the printer to the paper
type settings in the printer driver.
“Paper Size and Type Settings” on page 29
❏Use a higher quality setting on the control panel or the printer driver.
❏Align the print head.
“Aligning the Print Head” on page 114
Solving Problems
>
Cannot Solve Problem
>
Cannot Solve Printing or Copying Problems
215
❏Run a nozzle check to see if the print head nozzles are clogged.
If there are missing segments in the nozzle check pattern, the nozzles may be clogged. Repeat head cleaning and
the nozzle check alternately 3 times and check if the clogging has cleared.
Note that print head cleaning uses some ink.
“Checking and Cleaning the Print Head” on page 111
❏Turn o the printer, wait for at least 12 hours, and then check if the clogging has cleared.
If the problem is clogging, leaving the printer for a while without printing may solve the problem.
You can check the following items while the printer is o.
❏Check that you are using genuine Epson ink bottles.
Try to use genuine Epson ink bottles. e use of non-genuine ink bottles may cause print quality to decline.
❏Check if the translucent lm is smeared.
If there are smears on the translucent lm, carefully wipe o the smear.
“Cleaning the Translucent Film” on page 118
❏Make sure that there are no paper fragments le inside the printer.
When you remove the paper, do not touch the translucent lm with your hand or the paper.
❏Check the paper.
Check if the paper is curled or loaded with the printable side facing up.
“Paper Handling Precautions” on page 29
“Available Paper and Capacities” on page 239
“Unavailable Paper Types” on page 241
❏If you turn o the printer, wait for at least 12 hours, and if print quality has still not improved, run Power
Cleaning.
“Running Power Cleaning” on page 112
If you cannot solve the problem by checking the solutions above, you may need to request repairs. Contact Epson
support.
Related Information
&“Before Contacting Epson” on page 295
&“Contacting Epson Support” on page 295
Solving Problems
>
Cannot Solve Problem
>
Cannot Solve Printing or Copying Problems
216
Adding or Replacing the Computer or
Devices
Connecting to a Printer that has been Connected to the Network...............218
Re-setting the Network Connection....................................219
Connecting a Smart Device and Printer Directly (Wi-Fi Direct)................225
Checking the Network Connection Status................................229
Connecting to a Printer that has been Connected to
the Network
When the printer has already been connected to the network, you can connect a computer or a smart device to the
printer over the network.
Using a Network Printer from a Second Computer
We recommend using the installer to connect the printer to a computer. You can run the installer using one of the
following methods.
❏Setting up from the website
Access the following website, and then enter the product name. Go to Setup, and then start setting up.
http://epson.sn
❏Setting up using the soware disc (only for the models that come with a soware disc and users with Windows
computers with disc drives.)
Insert the soware disc into the computer, and then follow the on-screen instructions.
Selecting the Printer
Follow the on-screen instructions until the following screen is displayed, select the printer name you want to
connect to, and then click Next.
Follow the on-screen instructions.
Adding or Replacing the Computer or Devices
>
Connecting to a Printer that has been Connected t
…
218
Using a Network Printer from a Smart Device
You can connect a smart device to the printer using one of the following methods.
Connecting over a wireless router
Connect the smart device to the same Wi-Fi network (SSID) as the printer.
See the following for more details.
“Making Settings for Connecting to the Smart Device” on page 219
Connecting by Wi-Fi Direct
Connect the smart device to the printer directly without a wireless router.
See the following for more details.
“Connecting a Smart Device and Printer Directly (Wi-Fi Direct)” on page 225
Re-setting the Network Connection
is section explains how to make the network connection settings and change the connection method when
replacing the wireless router or the computer.
When Replacing the Wireless Router
When you replace the wireless router, make settings for the connection between the computer or the smart device
and the printer.
You need to make these settings if you change your Internet service provider and so on.
Making Settings for Connecting to the Computer
We recommend using the installer to connect the printer to a computer. You can run the installer using one of the
following methods.
❏Setting up from the website
Access the following website, and then enter the product name. Go to Setup, and then start setting up.
http://epson.sn
❏Setting up using the soware disc (only for the models that come with a soware disc and users with Windows
computers with disc drives.)
Insert the soware disc into the computer, and then follow the on-screen instructions.
Making Settings for Connecting to the Smart Device
You can use the printer from a smart device when you connect the printer to the same Wi-Fi network (SSID) as the
smart device. To use the printer from a smart device, set up from the following website. Access to the website from
the smart device that you want to connect to the printer.
http://epson.sn > Setup
Adding or Replacing the Computer or Devices
>
Re-setting the Network Connection
>
When Repl
…
219
When Changing the Computer
When changing the computer, make connection settings between the computer and the printer.
Making Settings for Connecting to the Computer
We recommend using the installer to connect the printer to a computer. You can run the installer using one of the
following methods.
❏Setting up from the website
Access the following website, and then enter the product name. Go to Setup, and then start setting up.
http://epson.sn
❏Setting up using the soware disc (only for the models that come with a soware disc and users with Windows
computers with disc drives.)
Insert the soware disc into the computer, and then follow the on-screen instructions.
Follow the on-screen instructions.
Changing the Connection Method to the Computer
is section explains how to change the connection method when the computer and the printer have been
connected.
Changing the Network Connection from Ethernet to Wi-Fi
Change the Ethernet connection to Wi-Fi connection from the printer's control panel. e changing connection
method is basically the same as the Wi-Fi connection settings.
Related Information
&“Making Wi-Fi Settings from the Control Panel” on page 221
Changing the Network Connection from Wi-Fi to Ethernet
Follow the steps below to change from a Wi-Fi connection to an Ethernet connection.
1. Select Settings on the home screen.
2. Select General Settings > Network Settings > Wired LAN Setup.
3. Follow the on-screen instructions.
Changing from USB to a Network Connection
Using the installer and re-set up in a dierent connection method.
Adding or Replacing the Computer or Devices
>
Re-setting the Network Connection
>
Changing t
…
220
❏Setting up from the website
Access the following website, and then enter the product name. Go to Setup, and then start setting up.
http://epson.sn
❏Setting up using the soware disc (only for the models that come with a soware disc and users with Windows
computers with disc drives.)
Insert the soware disc into the computer, and then follow the on-screen instructions.
Selecting Change the Connection Methods
Follow the on-screen instructions until the following screen is displayed.
Select the network connection that you want to use, Connect via wireless network (Wi-Fi) or Connect via wired
LAN (Ethernet), and then click Next.
Note:
e displayed connection method diers depending on the model.
Follow the on-screen instructions.
Making Wi-Fi Settings from the Control Panel
You can make network settings from the printer's control panel in several ways. Choose the connection method
that matches the environment and conditions that you are using.
If you know the information for the wireless router such as SSID and password, you can make settings manually.
If the wireless router supports WPS, you can make settings by using push button setup.
Adding or Replacing the Computer or Devices
>
Re-setting the Network Connection
>
Making Wi-
…
221
Aer connecting the printer to the network, connect to the printer from the device that you want to use (computer,
smart device, tablet, and so on.)
Related Information
&“Making Wi-Fi Settings by Entering the SSID and Password” on page 222
&“Making Wi-Fi Settings by Push Button Setup (WPS)” on page 223
&“Making Wi-Fi Settings by PIN Code Setup (WPS)” on page 224
Making Wi-Fi Settings by Entering the SSID and Password
You can set up a Wi-Fi network by entering the information necessary to connect to a wireless router from the
printer's control panel. To set up using this method, you need the SSID and password for a wireless router.
Note:
If you are using a wireless router with its default settings, the SSID and password are on the label. If you do not know the
SSID and password, see the documentation provided with the wireless router.
1. Tap on the home screen.
2. Select Wi-Fi (Recommended).
If the printer has already been connected by Ethernet, select Router.
3. Tap Start Setup.
If the network connection is already set up, the connection details are displayed. Tap Change Settings to
change the settings.
If the printer has already been connected by Ethernet, tap Change to Wi-Fi connection., and then select Ye s
aer checking the message.
4. Select Wi-Fi Setup Wizard.
5. Select the SSID for the wireless router.
Note:
❏If the SSID you want to connect to is not displayed on the printer's control panel, tap Search Again to update the list.
If it is still not displayed, tap Enter Manually, and then enter the SSID directly.
❏If you do not know the network name (SSID) check if the information is written on the label of the wireless router. If
you are using the wireless router with its default settings, use the SSID on the label. If you cannot nd any
information, see the documentation provided with the wireless router.
Adding or Replacing the Computer or Devices
>
Re-setting the Network Connection
>
Making Wi-
…
222
6. Tap Enter Password, and then enter the password.
Note:
❏e password is case-sensitive.
❏If you do not know the password, check if the information is written on the label of the wireless router. On the label,
the password may be written "Network Key", "Wireless Password", and so on. If you are using the wireless router
with its default settings, use the password written on the label.
7. When you have nished, tap OK.
8. Check the settings, and then tap Start Setup.
9. Tap OK to nish.
Note:
If you fail to connect, load A4 size plain paper, and then select Print Check Report to print a connection report.
10. Close the Network Connection Settings screen.
Related Information
&“Entering Characters” on page 26
&“Checking the Network Connection Status” on page 229
Making Wi-Fi Settings by Push Button Setup (WPS)
You can automatically set up a Wi-Fi network by pressing a button on the wireless routor. If the following
conditions are met, you can set up by using this method.
❏e wireless router is compatible with WPS (Wi-Fi Protected Setup).
❏e current Wi-Fi connection was established by pressing a button on the wireless router.
1. Tap on the home screen.
2. Select Wi-Fi (Recommended).
If the printer has already been connected by Ethernet, select Router.
3. Tap Start Setup.
If the network connection is already set up, the connection details are displayed. Tap Change Settings to
change the settings.
If the printer has already been connected by Ethernet, tap Change to Wi-Fi connection., and then select Ye s
aer checking the message.
4. Select Push Button Setup (WPS).
Adding or Replacing the Computer or Devices
>
Re-setting the Network Connection
>
Making Wi-
…
223
5. Hold down the [WPS] button on the wireless router until the security light ashes.
If you do not know where the [WPS] button is, or there are no buttons on the wireless router, see the
documentation provided with your wireless router for details.
6. Tap Start Setup on the printer.
7. Close the screen.
e screen automatically closes aer a specic length of time.
Note:
If connection fails, restart the wireless router, move it closer to the printer, and try again. If it still does not work, print a
network connection report and check the solution.
8. Close the Network Connection Settings screen.
Related Information
&“Checking the Network Connection Status” on page 229
Making Wi-Fi Settings by PIN Code Setup (WPS)
You can automatically connect to a wireless router by using a PIN code. You can use this method to set up if a
wireless router is capable of WPS (Wi-Fi Protected Setup). Use a computer to enter a PIN code into the wireless
router.
1. Tap on the home screen.
2. Select Wi-Fi (Recommended).
If the printer has already been connected by Ethernet, select Router.
3. Tap Start Setup.
If the network connection is already set up, the connection details are displayed. Tap Change Settings to
change the settings.
If the printer has already been connected by Ethernet, tap Change to Wi-Fi connection., and then select Ye s
aer checking the message.
Adding or Replacing the Computer or Devices
>
Re-setting the Network Connection
>
Making Wi-
…
224
4. Select Others > PIN Code Setup (WPS).
5. Use your computer to enter the PIN code (an eight digit number) displayed on the printer's control panel into
the wireless router within two minutes.
Note:
See the documentation provided with your wireless router for details on entering a PIN code.
6. Tap Start Setup on the printer's control panel.
7. Close the screen.
e screen automatically closes aer a specic length of time.
Note:
If connection fails, restart the wireless router, move it closer to the printer, and try again. If it still does not work, print a
connection report and check the solution.
8. Close the Network Connection Settings screen.
Related Information
&“Checking the Network Connection Status” on page 229
Connecting a Smart Device and Printer Directly (Wi-Fi
Direct)
Wi-Fi Direct (Simple AP) allows you to connect a smart device directly to the printer without a wireless router and
print from the smart device.
About Wi-Fi Direct
Use this connection method when you are not using Wi-Fi at home or at the oce, or when you want to connect
the printer and the computer or smart device directly. In this mode, the printer acts as an wireless router and you
can connect the devices to the printer without having to use a standard wireless router. However, devices directly
connected to the printer cannot communicate with each other through the printer.
Adding or Replacing the Computer or Devices
>
Connecting a Smart Device and Printer Directly (Wi
…
225
e printer can be connected by Wi-Fi or Ethernet, and Wi-Fi Direct (Simple AP) connection simultaneously.
However, if you start a network connection in Wi-Fi Direct (Simple AP) connection when the printer is connected
by Wi-Fi, the Wi-Fi is temporarily disconnected.
Connecting to Devices using Wi-Fi Direct
is method allows you to connect the printer directly to devices without a wireless router.
Note:
For iOS or Android users, it is convenient to set up from Epson Smart Panel.
You only need to make these settings for the printer and the device that you want to connect to once. Unless you disable Wi-
Fi Direct or restore the network settings to their defaults, you do not need to make these settings again.
1. Tap on the home screen.
2. Tap Wi-Fi Direct.
3. Tap Start Setup.
4. Select Other Methods.
5. Select Other OS Devices.
Adding or Replacing the Computer or Devices
>
Connecting a Smart Device and Printer Directly (Wi
…
226
6. On the device's Wi-Fi screen, select the SSID shown on the printer's control panel, and then enter the
password.
7. On the printing app screen for the device, select the printer that you want to connect to.
8. On the printer's control panel, select Complete.
For devices that have been connected to the printer before, select the network name (SSID) on the device's Wi-Fi
screen to connect them again.
Note:
If you are using an iOS device, you can also connect by scanning the QR code with the standard iOS camera. See the link
below http://epson.sn.
Adding or Replacing the Computer or Devices
>
Connecting a Smart Device and Printer Directly (Wi
…
227
Disconnecting Wi-Fi Direct (Simple AP) Connection
Note:
When Wi-Fi Direct (Simple AP) connection disabled, all computers and smart devices connected to the printer in Wi-Fi
Direct (Simple AP) connection are disconnected. If you want to disconnect a specic device, disconnect from the device
instead of the printer.
1. Tap on the home screen.
2. Select Wi-Fi Direct.
e Wi-Fi Direct information is displayed.
3. Tap Start Setup.
4. Tap .
5. Select Disable Wi-Fi Direct.
6. Tap the Disable the settings.
7. When a completion message is displayed, close the screen.
e screen automatically closes aer a specic length of time.
8. Close the Network Connection Settings screen.
Changing the Wi-Fi Direct (Simple AP) Settings Such as the SSID
When Wi-Fi Direct (simple AP) connection is enabled, you can change the settings from > Wi-Fi
Direct > Start Setup > , and then the following menu items are displayed.
Change Network Name
Change the Wi-Fi Direct (simple AP) network name (SSID) used for connecting to the printer to your arbitrary
name. You can set the network name (SSID) in ASCII characters that is displayed on the soware keyboard on the
control panel. You can enter up to 22 characters.
When changing the network name (SSID), all connected devices are disconnected. Use the new network name
(SSID) if you want to re-connect the device.
Change Password
Change the Wi-Fi Direct (simple AP) password for connecting to the printer to your arbitrary value. You can set
the password in ASCII characters that is displayed on the soware keyboard on the control panel. You can enter 8
to 22 characters.
When changing the password, all connected devices are disconnected. Use the new password if you want to re-
connect the device.
Adding or Replacing the Computer or Devices
>
Connecting a Smart Device and Printer Directly (Wi
…
228
Disable Wi-Fi Direct
Disable Wi-Fi Direct (simple AP) settings of the printer. When disabling it, all devices connected to the printer in
Wi-Fi Direct (Simple AP) connection are disconnected.
Restore Default Settings
Restore all Wi-Fi Direct (simple AP) settings to their defaults.
e Wi-Fi Direct (simple AP) connection information of the smart device saved to the printer is deleted.
Checking the Network Connection Status
You can check the network connection status in the following way.
Related Information
&“Checking the Network Connection Status from the Control Panel” on page 229
&“Printing a Network Connection Report” on page 230
Checking the Network Connection Status from the Control Panel
You can check the network connection status using the network icon or the network information on the printer’s
control panel.
Checking the Network Connection Status using the Network Icon
You can check the network connection status and strength of the radio wave using the network icon on the
printer's home screen.
Displaying Detailed Network Information on the Control Panel
When your printer is connected to the network, you can also view other network-related information by selecting
the network menus you want to check.
1. Select Settings on the home screen.
2. Select General Settings > Network Settings > Network Status.
Adding or Replacing the Computer or Devices
>
Checking the Network Connection Status
>
Chec
…
229
3. To check the information, select the menus that you want to check.
❏Wired LAN/Wi-Fi Status
Displays the network information (device name, connection, signal strength, and so on) for Ethernet or Wi-
Fi connections.
❏Wi-Fi Direct Status
Displays whether Wi-Fi Direct is enabled or disabled, and the SSID, password and so on for Wi-Fi Direct
connections.
❏Print Status Sheet
Prints a network status sheet. e information for Ethernet, Wi-Fi, Wi-Fi Direct, and so on is printed on
two or more pages.
Printing a Network Connection Report
You can print a network connection report to check the status between the printer and the wireless router.
1. Select Settings on the home screen.
2. Select General Settings > Network Settings > Connection Check.
e connection check starts.
3. Select Print Check Report.
4. Print the network connection report.
If an error has occurred, check the network connection report, and then follow the printed solutions.
Adding or Replacing the Computer or Devices
>
Checking the Network Connection Status
>
Printi
…
230
Messages and Solutions on the Network Connection Report
Check the messages and error codes on the network connection report, and then follow the solutions.
a. Error code
b. Messages on the Network Environment
Related Information
&“E-1” on page 232
&“E-2, E-3, E-7” on page 232
&“E-5” on page 233
&“E-6” on page 233
&“E-8” on page 233
&“E-9” on page 234
&“E-10” on page 234
&“E-11” on page 234
&“E-12” on page 235
&“E-13” on page 235
&“Message on the Network Environment” on page 236
Adding or Replacing the Computer or Devices
>
Checking the Network Connection Status
>
Printi
…
231
E-1
Solutions:
❏Make sure the Ethernet cable is securely connected to your printer and to your hub or other network device.
❏Make sure your hub or other network device is turned on.
❏If you want to connect the printer by Wi-Fi, make Wi-Fi settings for the printer again because it is disabled.
E-2, E-3, E-7
Solutions:
❏Make sure your wireless router is turned on.
❏Conrm that your computer or device is connected correctly to the wireless router.
❏Turn o the wireless router. Wait for about 10 seconds, and then turn it on.
❏Place the printer closer to your wireless router and remove any obstacles between them.
❏If you have entered the SSID manually, check if it is correct. Check the SSID from the Network Status part on
the network connection report.
❏If an wireless router has multiple SSIDs, select the SSID that is displayed. When the SSID is using a non-
compliant frequency, the printer does not display them.
❏If you are using push button setup to establish a network connection, make sure your wireless router supports
WPS. You cannot use push button setup if your wireless router does not support WPS.
❏Makes sure your SSID uses only ASCII characters (alphanumeric characters and symbols). e printer cannot
display an SSID that contains non-ASCII characters.
❏Makes sure you know your SSID and password before connecting to the wireless router. If you are using a
wireless router with its default settings, the SSID and password are located on a label on the wireless router. If
you do not know your SSID and password, contact the person who set up the wireless router, or see the
documentation provided with the wireless router.
❏If you are connecting to an SSID generated from a tethering smart device, check for the SSID and password in
the documentation provided with the smart device.
❏If your Wi-Fi connection suddenly disconnects, check for the conditions below. If any of these conditions are
applicable, reset your network settings by downloading and running the soware from the following website.
http://epson.sn > Setup
❏Another smart device was added to the network using push button setup.
❏e Wi-Fi network was set up using any method other than push button setup.
Related Information
&“Making Settings for Connecting to the Computer” on page 220
&“Making Wi-Fi Settings from the Control Panel” on page 221
Adding or Replacing the Computer or Devices
>
Checking the Network Connection Status
>
Printi
…
232
E-5
Solutions:
Make sure the wireless router’s security type is set to one of the following. If it is not, change the security type on
the wireless router, and then reset the printer’s network settings.
❏WEP-64 bit (40 bit)
❏WEP-128 bit (104 bit)
❏WPA PSK (TKIP/AES)
*
❏WPA2 PSK (TKIP/AES)
*
❏WPA (TKIP/AES)
❏WPA2 (TKIP/AES)
* WPA PSK is also known as WPA Personal. WPA2 PSK is also known as WPA2 Personal.
E-6
Solutions:
❏Check if MAC address ltering is disabled. If it is enabled, register the printer’s MAC address so that it is not
ltered. See the documentation provided with the wireless router for details. You can check the printer’s MAC
address from the Network Status part on the network connection report.
❏If your wireless router is using shared authentication with WEP security, make sure the authentication key and
index are correct.
❏If the number of connectable devices on the wireless router is less than the number of network devices that you
want to connect, make settings on the wireless router to increase the number of connectable devices. See the
documentation provided with the wireless router to make settings.
Related Information
&“Making Settings for Connecting to the Computer” on page 220
E-8
Solutions:
❏Enable DHCP on the wireless router if the printer’s Obtain IP Address setting is set to Auto.
❏If the printer’s Obtain IP Address setting is set to Manual, the IP address you manually set is invalid due to out
of range (for example: 0.0.0.0). Set a valid IP address from the printer’s control panel.
Related Information
&“Network Settings” on page 254
Adding or Replacing the Computer or Devices
>
Checking the Network Connection Status
>
Printi
…
233
E-9
Solutions:
Check the following.
❏Devices are turned on.
❏You can access the Internet and other computers or network devices on the same network from the devices you
want to connect to the printer.
If still does not connect your printer and network devices aer conrming the above, turn o the wireless router.
Wait for about 10 seconds, and then turn it on. en reset your network settings by downloading and running the
installer from the following website.
http://epson.sn > Setup
Related Information
&“Making Settings for Connecting to the Computer” on page 220
E-10
Solutions:
Check the following.
❏Other devices on the network are turned on.
❏Network addresses (IP address, subnet mask, and default gateway) are correct if you have set the printer’s
Obtain IP Address to Manual.
Reset the network address if they are incorrect. You can check the IP address, subnet mask, and default gateway
from the Network Status part on the network connection report.
If DHCP is enabled, change the printer’s Obtain IP Address setting to Auto. If you want to set the IP address
manually, check the printer’s IP address from the Network Status part on the network connection report, and then
select Manual on the network settings screen. Set the subnet mask to [255.255.255.0].
If still does not connect your printer and network devices, turn o the wireless router. Wait for about 10 seconds,
and then turn it on.
Related Information
&“Network Settings” on page 254
E-11
Solutions:
Check the following.
❏e default gateway address is correct if you set the printer’s TCP/IP Setup setting to Manual.
❏e device that is set as the default gateway is turned on.
Set the correct default gateway address. You can check the default gateway address from the Network Status part
on the network connection report.
Adding or Replacing the Computer or Devices
>
Checking the Network Connection Status
>
Printi
…
234
Related Information
&“Network Settings” on page 254
E-12
Solutions:
Check the following.
❏Other devices on the network are turned on.
❏e network addresses (IP address, subnet mask, and default gateway) are correct if you are entering them
manually.
❏e network addresses for other devices (subnet mask and default gateway) are the same.
❏e IP address does not conict with other devices.
If still does not connect your printer and network devices aer conrming the above, try the following.
❏Turn o the wireless router. Wait for about 10 seconds, and then turn it on.
❏Make network settings again using the installer. You can run it from the following website.
http://epson.sn > Setup
❏You can register several passwords on a wireless router that uses WEP security type. If several passwords are
registered, check if the rst registered password is set on the printer.
Related Information
&“Network Settings” on page 254
&“Making Settings for Connecting to the Computer” on page 220
E-13
Solutions:
Check the following.
❏Network devices such as a wireless router, hub, and router are turned on.
❏e TCP/IP Setup for network devices has not been set up manually. (If the printer’s TCP/IP Setup is set
automatically while the TCP/IP Setup for other network devices is performed manually, the printer’s network
may dier from the network for other devices.)
If it still does not work aer checking the above, try the following.
❏Turn o the wireless router. Wait for about 10 seconds, and then turn it on.
❏Make network settings on the computer that is on the same network as the printer using the installer. You can
run it from the following website.
http://epson.sn > Setup
❏You can register several passwords on a wireless router that uses the WEP security type. If several passwords are
registered, check if the rst registered password is set on the printer.
Adding or Replacing the Computer or Devices
>
Checking the Network Connection Status
>
Printi
…
235
Message on the Network Environment
Message Solution
The Wi-Fi environment needs to be
improved. Turn the wireless router o and
then turn it on. If the connection does not
improve, see the documentation for the
wireless router.
After moving the printer closer to the wireless router and removing any
obstacles between them, turn o the wireless router. Wait for about 10
seconds, and then turn it on. If it still does not connect, see the
documentation supplied with the wireless router.
*No more devices can be connected.
Disconnect one of the connected devices if
you want to add another one.
Computer and smart devices that can be connected simultaneously are
connected in full in the Wi-Fi Direct (Simple AP) connection. To add another
computer or smart device, disconnect one of the connected devices or
connect it to the other network rst.
You can conrm the number of wireless devices which can be connected
simultaneously and the number of connected devices by checking the
network status sheet or the printer’s control panel.
The same SSID as Wi-Fi Direct exists in the
environment. Change the Wi-Fi Direct SSID
if you cannot connect a smart device to the
printer.
On the printer’s control panel, go to Wi-Fi Direct Setup screen and select the
menu to change the setting. You can change the network name following
after DIRECT-XX-. Enter within 22 characters.
Printing a Network Status Sheet
You can check the detailed network information by printing it.
1. Select Settings on the home screen.
2. Select General Settings > Network Settings > Network Status.
3. Select Print Status Sheet.
4. Check the message, and then print the network status sheet.
Checking the Network of the Computer (Windows only)
By using the command prompt, check the connection status of the computer and the connection path to the
printer. is will lead you to solve the problems.
Adding or Replacing the Computer or Devices
>
Checking the Network Connection Status
>
Chec
…
236
❏ipcong command
Display the connection status of the network interface that is currently used by the computer.
By comparing the setting information with actual communication, you can check whether the connection is
correct. In case there are multiple DHCP servers on the same network, you can nd out the actual address
assigned to the computer, the referred DNS server, etc.
❏Format : ipcong /all
❏Examples :
❏pathping command
You c a n conrm the list of routers passing through the destination host and the routing of communication.
❏Format : pathping xxx.xxx.xxx.xxx
❏Examples : pathping 192.0.2.222
Adding or Replacing the Computer or Devices
>
Checking the Network Connection Status
>
Chec
…
237
Product Information
Paper Information.................................................239
Consumable Products Information.....................................242
Soware Information.............................................. 243
Settings Menu List.................................................251
Product Specications..............................................265
Regulatory Information.............................................272
Paper Information
Available Paper and Capacities
Genuine Epson Paper
Epson recommends using genuine Epson paper to ensure high-quality printouts.
Note:
❏e availability of paper varies by location. For the latest information on paper available in your area, contact Epson
support.
❏See the following for information on available paper types for 2-sided printing.
“Paper for 2-Sided Printing” on page 241
❏When printing on genuine Epson paper at a user dened size, only Standard or Normal print quality settings are
available. Although some printer drivers allow you to select a better print quality, the printouts are printed using
Standard or Normal.
Paper suitable for printing documents
Media Name Size Loading Capacity (Sheets)
Paper Cassette Rear Paper Feed Slot
Epson Bright White Ink Jet Paper A4 200 1
Paper suitable for printing documents and photos
Media Name Size Loading Capacity (Sheets)
Paper Cassette Rear Paper Feed Slot
Epson Photo Quality Ink Jet Paper A4 100 1
Epson Double-sided Photo Quality
Ink Jet Paper
A4 80 1
Epson Matte Paper-Heavyweight A4 20 1
Epson Double-Sided Matte Paper A4 1 1
Paper suitable for printing photos
Media Name Size Loading Capacity (Sheets)
Paper Cassette Rear Paper Feed Slot
Epson Ultra Glossy Photo Paper A4, 13x18 cm (5x7 in.), 10x15
cm (4x6 in.)
20 1
Product Information
>
Paper Information
>
Available Paper and Capacities
239
Media Name Size Loading Capacity (Sheets)
Paper Cassette Rear Paper Feed Slot
Epson Premium Glossy Photo
Paper
A4, 13x18 cm (5x7 in.), 10x15
cm (4x6 in.)
20 1
Epson Premium Semigloss Photo
Paper
A4, 13x18 cm (5x7 in.), 10x15
cm (4x6 in.)
20 1
Epson Photo Paper Glossy A4, 13x18 cm (5x7 in.), 10x15
cm (4x6 in.)
20 1
Various other paper types
Media Name Size Loading Capacity (Sheets)
Paper Cassette Rear Paper Feed Slot
Epson Photo Quality Self Adhesive
Sheets
A4 1 1
Commercially Available Paper
Note:
See the following for information on available paper types for 2-sided printing.
“Paper for 2-Sided Printing” on page 241
Plain papers
Plain paper includes copy paper and letterhead*1.
Size Loading Capacity (Sheets)
Paper Cassette Rear Paper Feed Slot
Letter, A4, B5, A5, A6, B6, 16K (195×270
mm)
250 1
Legal, Indian-Legal, 8.5×13 in. 50 1
User Dened
*2
(mm)
54x86 to 215.9x1200
-1
User Dened
*2
(mm)
89x127 to 215.9x1200
1-
*1 Paper on which information such as the sender's name or corporation name are pre-printed in the header. There must be a
margin of 5 mm or more at the top of the paper. 2-sided printing are not available for letterhead paper.
*2 Only printing from computer is available.
Product Information
>
Paper Information
>
Available Paper and Capacities
240
Thick papers
Size Loading Capacity (Sheets)
Paper Cassette Rear Paper Feed Slot
Legal, Letter, 8.5×13 in., A4, B5, A5, A6,
B6, 16K (195×270 mm), Indian-Legal
-1
User Dened
*
(mm)
54x86 to 215.9x1200
-1
* Only printing from computer is available.
Envelope
Size Loading Capacity (Envelopes)
Paper Cassette Rear Paper Feed Slot
Envelope #10, Envelope DL, Envelope
C6
10 1
Paper for 2-Sided Printing
Genuine Epson Paper
Epson Bright White Ink Jet Paper
Related Information
&“Available Paper and Capacities” on page 239
Commercially Available Paper
Plain paper, Copy paper
*
* Letter, A4, B5, 16K, and user-dened size (182x257 to 215.9x297 mm) paper is supported for 2-sided printing.
Related Information
&“Available Paper and Capacities” on page 239
Unavailable Paper Types
Do not use the following papers. Using these types of paper causes paper jams and smears on the printout.
❏Papers that are wavy
❏Papers that are torn or cut
❏Papers that are folded
Product Information
>
Paper Information
>
Unavailable Paper Types
241
❏Papers that are damp
❏Papers that are too thick or too thin
❏Papers that have stickers
Do not use the following envelopes. Using these types of envelope causes paper jams and smears on the printout.
❏Envelopes that are curled or folded
❏Envelopes with adhesive surfaces on the aps or window envelopes
❏Envelopes that are too thin
ey may curl during printing.
Consumable Products Information
Ink Bottle Codes
Epson recommends the use of genuine Epson ink bottles.
e following are the codes for genuine Epson ink bottles.
c
Important:
❏Epson warranty does not cover damage caused by inks other than those specied, including any genuine Epson
ink not designed for this printer or any third party ink.
❏Other products not manufactured by Epson may cause damage that is not covered by Epson’s warranties, and
under certain circumstances, may cause erratic printer behavior.
Note:
❏Ink bottle codes may vary by location. For the correct codes in your area, contact Epson support.
❏Although the ink bottles may contain recycled materials, this does not aect printer function or performance.
❏Specications and appearance of the ink bottle are subject to change without prior notice for improvement.
For Europe
Product BK: Black C: Cyan M: Magenta Y: Yellow
ET-5170 Series/
ET-5150 Series
113 113 113 113
L6490 Series/L6460
Series
112 112 112 112
Note:
Visit the following website for information on Epson's ink bottle yields.
http://www.epson.eu/pageyield
Product Information
>
Consumable Products Information
>
Ink Bottle Codes
242
For Australia and New Zealand
BK: Black C: Cyan M: Magenta Y: Yellow
542 542 542 542
For Asia
BK: Black C: Cyan M: Magenta Y: Yellow
008 008 008 008
Maintenance Box Code
e maintenance box can be purchased and replaced by the user.
Epson recommends the use of a genuine Epson maintenance box.
e following is the code for the genuine Epson maintenance box.
T04D1
c
Important:
Once a maintenance box has been installed in a printer it cannot be used with other printers.
Software Information
is section introduces the network services and soware products available for your printer from the Epson
website.
Software for Printing
Application for Printing from a Computer (Windows Printer Driver)
e printer driver controls the printer according to the commands from an application. Making settings on the
printer driver provides the best printing results. You can also check the status of the printer or keep it in top
operating condition using the printer driver utility.
Note:
You can change the language of the printer driver. Select the language you want to use from the Language setting on the
Maintenance tab.
Accessing the printer driver from applications
To make settings that apply only to the application you are using, access from that application.
Select Print or Print Setup from the File menu. Select your printer, and then click Preferences or Properties.
Note:
Operations dier depending on the application. See the application's help for details.
Product Information
>
Software Information
>
Software for Printing
243
Accessing the printer driver from the control panel
To make settings that apply to all of the applications, access from the control panel.
❏Windows 10/Windows Server 2019/Windows Server 2016
Click on the start button, and then select Windows System > Control Panel > View devices and printers in
Hardware and Sound. Right-click on your printer, or press and hold it and then select Printing preferences
❏Windows 8.1/Windows 8/Windows Server 2012 R2/Windows Server 2012
Select Desktop > Settings > Control Panel > View devices and printers in Hardware and Sound. Right-click
on your printer, or press and hold it and then select Printing preferences
❏Windows 7/Windows Server 2008 R2
Click the start button, and select Control Panel > View devices and printers in Hardware and Sound. Right-
click on your printer and select Printing preferences.
❏Windows Vista/Windows Server 2008
Click the start button, and select Control Panel > Printers in Hardware and Sound. Right-click on your printer
and select Printing preferences.
❏Windows XP/Windows Server 2003 R2/Windows Server 2003
Click the start button, and select Control Panel > Printers and Other Hardware > Printers and Faxes. Right-
click on your printer and select Printing preferences.
Accessing the printer driver from the printer icon on the task bar
e printer icon on the desktop task bar is a shortcut icon allowing you to quickly access the printer driver.
If you click the printer icon and select Printer Settings, you can access the same printer settings window as the one
displayed from the control panel. If you double-click this icon, you can check the status of the printer.
Note:
If the printer icon is not displayed on the task bar, access the printer driver window, click Monitoring Preferences on the
Maintenance tab, and then select Register the shortcut icon to the taskbar.
Starting the utility
Access the printer driver window. Click the Maintenance tab.
Making Operation Settings for the Windows Printer Driver
You can make settings such as enabling EPSON Status Monitor 3.
1. Access the printer driver window.
2. Click Extended Settings on the Maintenance tab.
3. Make the appropriate settings, and then click OK.
See the online help for explanations of the setting items.
Related Information
&“Application for Printing from a Computer (Windows Printer Driver)” on page 243
Product Information
>
Software Information
>
Software for Printing
244
Application for Printing from a Computer (Mac OS Printer Driver)
e printer driver controls the printer according to the commands from an application. Making settings on the
printer driver provides the best printing results. You can also check the status of the printer or keep it in top
operating condition using the printer driver utility.
Accessing the printer driver from applications
Click Page Setup or Print on the File menu of your application. If necessary, click Show Details (or
d
) to expand
the print window.
Note:
Depending on the application being used, Page Setup may not be displayed in the File menu, and the operations for
displaying the print screen may dier.See the application's help for details.
Starting the utility
Select System Preferences from the Apple menu > Printers & Scanners (or Print & Scan, Print & Fax), and then
select the printer. Click Options & Supplies > Utility > Open Printer Utility.
Guide to Mac OS Printer Driver
Epson Printer Utility
You can run a maintenance feature such as nozzle check and print head cleaning, and by starting EPSON Status
Monitor, you can check printer status and error information.
Accessing the Operation Settings Window of the Mac OS Printer Driver
Select System Preferences from the Apple menu > Printers & Scanners (or Print & Scan, Print & Fax), and then
select the printer. Click Options & Supplies > Options (or Driver).
Product Information
>
Software Information
>
Software for Printing
245
Application for Quick and Fun Printing from a Computer (Epson Photo+)
Epson Photo+ is an application that allows you to easily print images with a variety of layouts. You can also
perform image correction and adjust the position while viewing a preview of your document. You can also
brighten up your images by adding text and stamps wherever you like. When printing on genuine Epson photo
paper, the ink performance is maximized creating a beautiful nish with excellent coloring.
See the application's help for details.
Note:
❏Windows Server operating systems are not supported.
❏To use this application the printer driver for this printer must be installed.
Starting on Windows
❏Windows 10
Click the start button, and then select Epson Soware > Epson Photo+.
❏Windows 8.1/Windows 8
Enter the application name in the search charm, and then select the displayed icon.
❏Windows 7/Windows Vista/Windows XP
Click the start button, and select All Programs or Programs > Epson Soware > Epson Photo+.
Starting on Mac OS
Select Go > Applications > Epson Soware > Epson Photo+.
Related Information
&“Installing the Applications Separately” on page 123
Application for Easily Operating the Printer from a Smart device (Epson Smart
Panel)
Epson Smart Panel is an application that allows you to perform printer operations easily including printing,
copying, or scanning from a smart device such as a smartphone or tablet. You can connect the printer and smart
device over a wireless network, check the ink levels and printer status, and check for solutions if an error occurs.
You can also copy easily by registering a copy favorite.
Search for and install Epson Smart Panel from App Store or Google Play.
Application for Printing Easily from an Android Application (Epson Print
Enabler)
Epson Print Enabler is an application that allows you to wirelessly print your documents, emails, photos, and web
pages right from your Android phone or tablet (Android v4.4 or later). With a few taps, your Android device will
discover an Epson printer that is connected to the same wireless network.
Product Information
>
Software Information
>
Software for Printing
246
Search for and install Epson Print Enabler from Google Play.
Software for Scanning
Application for Scanning from a Computer (Epson ScanSmart)
is application allows you to scan documents easily, and then save the scanned images in simple steps.
See the Epson ScanSmart help for details on using the features.
Starting on Windows
❏Windows 10
Click the start button, and then select Epson Soware > Epson ScanSmart.
❏Windows 8.1/Windows 8
Enter the application name in the search charm, and then select the displayed icon.
❏Windows 7
Click the start button, and then select All Programs > Epson Soware > Epson ScanSmart.
Starting on Mac OS
Select Go > Applications > Epson Soware > Epson ScanSmart.
Software for Faxing
Application for Conguring Fax Operations and Sending Faxes (FAX Utility)
FAX Utility is an application that allows you to congure various settings for sending faxes from a computer. You
can create or edit the contacts list to be used when sending a fax, congure to save received faxes in PDF format on
the computer, and so on. See the application's help for details.
Note:
❏Windows Server operating systems are not supported.
❏Make sure you have installed the printer driver before installing FAX Utility.
❏Make sure the FAX Utility has been installed. See "Starting on Windows" or "Starting on Mac OS" below to check if the
application has been installed.
Starting on Windows
❏Windows 10
Click the start button, and select Epson Soware > FAX Utility.
❏Windows 8.1/Windows 8
Enter the application name in the search charm, and then select the displayed icon.
❏Windows 7/Windows Vista/Windows XP
Click the start button, and select All Programs (or Programs) > Epson Soware > FAX Utility.
Product Information
>
Software Information
>
Software for Faxing
247
Starting on Mac OS
Select System Preferences from the Apple menu > Printers & Scanners (or Print & Scan, Print & Fax), and then
select the printer (FAX). Click Options & Supplies > Utility > Open Printer Utility.
Related Information
&“Sending a Fax from a Computer” on page 100
&“Receiving Faxes on a Computer” on page 104
Application for Sending Faxes (PC-FAX Driver)
PC-FAX driver is an application that allows you to send a document created on a separate application as a fax
directly from the computer. PC-FAX driver is installed when you install FAX Utility. See the application's help for
details.
Note:
❏Windows Server operating systems are not supported.
❏Check if PC-FAX driver has been installed. See "Accessing from Windows" or "Accessing from Mac OS" below.
❏e operation diers depending on the application you used to create the document. See the application's help for details.
Accessing from Windows
In the application, select Print or Print Setup from the File menu. Select your printer (FAX), and then click
Preferences or Properties.
Accessing from Mac OS
In the application, select Print from the File menu. Select your printer (FAX) as the Printer setting, and then select
Fax Settings or Recipient Settings from the pop-up menu.
Related Information
&“Sending a Fax from a Computer” on page 100
Software for Package Creation
Application for Creating Driver Packages (EpsonNet SetupManager)
EpsonNet SetupManager is a soware to create a package for a simple printer installation, such as installing the
printer driver, installing EPSON Status Monitor and creating a printer port. is soware allows the administrator
to create unique soware packages and distribute them among groups.
For more information, visit your regional Epson website.
http://www.epson.com
Product Information
>
Software Information
>
Software for Package Creation
248
Software for Making Settings
Application for Conguring Printer Operations (Web Cong)
Web Cong is an application that runs in a web browser, such as Internet Explorer and Safari, on a computer or
smart device. You can conrm the printer status or change the network service and printer settings. To use the
Web Cong, connect the printer and the computer or device to the same network.
e following browsers are supported.
Microso Edge, Internet Explorer 8 or later, Firefox
*
, Chrome
*
, Safari
*
*Use the latest version.
Note:
If the administrator password has not been set when accessing Web Cong, the password must be set on the administrator
password setting page.
Do not forget the user name and the password. If you forget them, you will need to contact Epson service support.
Running Web Cong on a Web Browser
1. Check the printer's IP address.
Select the network icon on the printer's home screen, and then select the active connection method to conrm
the printer's IP address.
Note:
You can also check the IP address by printing the network connection report.
2. Launch a Web browser from a computer or smart device, and then enter the printer's IP address.
Format:
IPv4: http://the printer's IP address/
IPv6: http://[the printer's IP address]/
Examples:
IPv4: http://192.168.100.201/
IPv6: http://[2001:db8::1000:1]/
Note:
Using the smart device, you can also run Web Cong from the product information screen of the Epson Smart Panel.
Since the printer uses a self-signed certicate when accessing HTTPS, a warning is displayed on the browser
when you start Web Cong; this does not indicate a problem and can be safely ignored.
Related Information
&“Printing a Network Connection Report” on page 230
Running Web Cong on Windows
When connecting a computer to the printer using WSD, follow the steps below to run Web Cong.
Product Information
>
Software Information
>
Software for Making Settings
249
1. Open the printer list on the computer.
❏Windows 10
Click on the start button, and then select Windows System > Control Panel > View devices and printers
in Hardware and Sound.
❏Windows 8.1/Windows 8
Select Desktop > Settings > Control Panel > View devices and printers in Hardware and Sound (or
Hardware).
❏Windows 7
Click the start button, and select Control Panel > View devices and printers in Hardware and Sound.
❏Windows Vista
Click the start button, and select Control Panel > Printers in Hardware and Sound.
2. Right-click on your printer and select Properties.
3. Select the Web S er vice tab and click the URL.
Since the printer uses a self-signed certicate when accessing HTTPS, a warning is displayed on the browser
when you start Web Cong; this does not indicate a problem and can be safely ignored.
Running Web Cong on Mac OS
1. Select System Preferences from the Apple menu > Printers & Scanners (or Print & Scan, Print & Fax), and
then select the printer.
2. Click Options & Supplies> Show Printer Webpage.
Since the printer uses a self-signed certicate when accessing HTTPS, a warning is displayed on the browser
when you start Web Cong; this does not indicate a problem and can be safely ignored.
Application for Setting up the Device on a Network (EpsonNet Cong)
EpsonNet Cong is an application that allows you to set the network interface addresses and protocols. See the
operations guide for EpsonNet Cong or the application's help for more details.
Starting on Windows
❏Windows 10/Windows Server 2019/Windows Server 2016
Click the start button, and then select EpsonNet > EpsonNet Cong.
❏Windows 8.1/Windows 8/Windows Server 2012 R2/Windows Server 2012
Enter the application name in the search charm, and then select the displayed icon.
❏Windows 7/Windows Vista/Windows XP/Windows Server 2008 R2/Windows Server 2008/Windows Server
2003 R2/Windows Server 2003
Click the start button, and select All Programs or Programs > EpsonNet > EpsonNet Cong SE > EpsonNet
Cong.
Starting on Mac OS
Go > Applications > Epson Soware > EpsonNet > EpsonNet Cong SE > EpsonNet Cong.
Product Information
>
Software Information
>
Software for Making Settings
250
Related Information
&“Installing the Applications Separately” on page 123
Software for Updating
Application for Updating Software and Firmware (EPSON Software Updater)
EPSON Soware Updater is an application that installs new soware, and updates rmware over the Internet. If
you want to check for update information regularly, you can set the interval for checking for updates in EPSON
Soware Updater's Auto Update Settings.
Note:
Windows Server operating systems are not supported.
Starting on Windows
❏Windows 10
Click the start button, and then select Epson Soware > EPSON Soware Updater.
❏Windows 8.1/Windows 8
Enter the application name in the search charm, and then select the displayed icon.
❏Windows 7/Windows Vista/Windows XP
Click the start button, and then select All Programs (or Programs) > Epson Soware > EPSON Soware
Updater.
Note:
You can also start EPSON Soware Updater by clicking the printer icon on the task bar on the desktop, and then selecting
Soware Update.
Starting on Mac OS
Select Go > Applications > Epson Soware > EPSON Soware Updater.
Related Information
&“Installing the Applications Separately” on page 123
Settings Menu List
Select Settings on the home screen of the printer to make various settings.
General Settings
Select the menus on the control panel as described below.
Settings > General Settings
Product Information
>
Settings Menu List
>
General Settings
251
Basic Settings
Select the menus on the control panel as described below.
Settings > General Settings > Basic Settings
LCD Brightness:
Adjust the brightness of the LCD screen.
Sound:
Adjust the volume.
❏Mute
Select On to mute sounds such as those emitted by Button Press.
❏Normal Mode
Select the volume such as Button Press.
❏Quiet Mode
Select the volume such as Button Press in Quiet Mode.
Sleep Timer:
Adjust the time period to enter a sleep mode (energy saving mode) when the printer has not
performed any operations. e LCD screen turns black when the setting time passes.
Power O Timer:
Your product may have this feature or the Power O Settings feature depending on the location of
purchase.
Select this setting to turn the printer o automatically when it is not used for a specied period of
time. You can adjust the time before power management is applied. Any increase will aect the
product’s energy eciency. Please consider the environment before making any change.
Power O Settings:
Your product may have this feature or the Power O Timer feature depending on the location of
purchase.
❏Power O If Inactive
Select this setting to turn the printer o automatically if it is not used for a specied period of
time. Any increase will aect the product’s energy eciency. Please consider the environment
before making any change.
❏Power O If Disconnected
Select this setting to turn the printer o aer 30 minutes when all ports including the LINE port
are disconnected. is feature may not be available depending on your region.
Date/Time Settings:
❏Date/Time
Enter the current date and time.
❏Daylight Saving Time
Select the summer time setting that applies to your area.
Product Information
>
Settings Menu List
>
General Settings
252
❏Time Dierence
Enter the time dierence between your local time and UTC (Coordinated Universal Time).
Country/Region:
Select the country or region in which you are using your printer. If you change the country or region,
your fax settings return to their defaults and you must select them again.
Language:
Select the language used on the LCD screen.
Operation Time Out:
Select On to return to the initial screen when no operations have been performed for the specied
time.
Keyboard:
Change the layout of the keyboard on the LCD screen.
Related Information
&“Saving Power” on page 122
&“Entering Characters” on page 26
Printer Settings
Select the menus on the control panel as described below.
Settings > General Settings > Printer Settings
Paper Source Settings:
Paper Setting:
Select the paper size and paper type you loaded in the paper source. You can make Favorite
Paper Settings in paper size and paper type.
A4/Letter Auto Switching:
Select On to feed paper from the paper source set as A4 size when there is no paper source set
as Letter, or feed from the paper source set as Letter size when there is no paper source set as
A4.
Error Notice:
Select On to display an error message when the selected paper size or type does not match the
loaded paper.
Paper Setup Auto Display:
Select On to display the Paper Setting screen when loading paper in the paper cassette. If you
disable this feature, you cannot print from an iPhone, iPad, or iPod touch using AirPrint.
Product Information
>
Settings Menu List
>
General Settings
253
Universal Print Settings:
ese print settings are applied when you print by an external device without using the printer driver.
e oset settings are applied when you print using the printer driver.
Top Oset:
Adjust the top margin of the paper.
Left Oset:
Adjust the le margin of the paper.
Top Oset in Back:
Adjust the top margin for the back of the page when performing 2-sided printing.
Left Oset in Back:
Adjust the le margin for the back of the page when performing 2-sided printing.
Skip Blank Page:
Skips blank pages in the print data automatically.
Auto Error Solver:
Select an action to perform when a 2-sided printing error or a memory full error occurs.
❏On
Displays a warning and prints in single-sided mode when a 2-sided printing error occurs, or prints
only what the printer could process when a memory full error occurs.
❏O
Displays an error message and cancels printing.
Quiet Mode:
Select On to reduce noise during printing, however, this may lower the print speed. Depending on
the paper type and print quality settings you selected, there may be no dierence in the printer's noise
level.
Ink Drying Time:
Select the ink drying time you want to use when performing 2-sided printing. e printer prints the
other side aer printing one side. If your printout is smeared, increase the time setting.
PC Connection via USB:
Select Enable to allow a computer to access the printer when connected by USB. When Disable is
selected, printing and scanning that is not sent over a network connection is restricted.
Related Information
&“Loading Paper” on page 31
Network Settings
Select the menus on the control panel as described below.
Product Information
>
Settings Menu List
>
General Settings
254
Settings > General Settings > Network Settings
Wi-Fi Setup:
Set up or change wireless network settings. Choose the connection method from following and then
follow the instructions on the control panel.
Wi-Fi (Recommended):
❏Wi-Fi Setup Wizard
❏Push Button Setup (WPS)
❏Others
❏PIN Code Setup (WPS)
❏Wi-Fi Auto Connect
❏Disable Wi-Fi
You may be able to resolve network problems by disabling the Wi-Fi settings or making
the Wi-Fi settings again. Select > Wi-Fi (Recommended) > Change
Settings > Others > Disable Wi-Fi > Start Setup.
Wi-Fi Direct:
❏iOS
❏Other OS Devices
❏Menu
❏Change Network Name
❏Change Password
❏Disable Wi-Fi Direct
❏Restore Default Settings
Wired LAN Setup:
Set up or change a network connection that uses a LAN cable and router. When this is being used,
Wi-Fi connections are disabled.
Network Status:
Displays or prints the current network settings.
❏Wired LAN/Wi-Fi Status
❏Wi-Fi Direct Status
❏Print Status Sheet
Connection Check:
Checks the current network connection and prints a report. If there are any problems with the
connection, see the report to solve the problem.
Advanced:
Make the following detailed settings.
❏Device Name
Product Information
>
Settings Menu List
>
General Settings
255
❏TCP/IP
❏Proxy Server
❏IPv6 Address
❏Link Speed & Duplex
Related Information
&“Making Wi-Fi Settings by Entering the SSID and Password” on page 222
&“Making Wi-Fi Settings by Push Button Setup (WPS)” on page 223
&“Making Wi-Fi Settings by PIN Code Setup (WPS)” on page 224
&“Connecting a Smart Device and Printer Directly (Wi-Fi Direct)” on page 225
&“Printing a Network Connection Report” on page 230
&“Checking the Network Connection Status” on page 229
&“Changing the Network Connection from Wi-Fi to Ethernet” on page 220
Web Service Settings
Select the menus on the control panel as described below.
Settings > General Settings > Web Service Settings
Epson Connect Services:
Displays whether the printer is registered and connected to Epson Connect.
You can register to the service by selecting Register and follow the instructions.
When you have registered, you can change the following settings.
❏Suspend/Resume
❏Unregister
For details, see the following web site.
https://www.epsonconnect.com/
http://www.epsonconnect.eu (Europe only)
Related Information
&“Printing Using a Cloud Service” on page 65
Fax Settings
Faxing feature is available only for ET-5170 Series/L6490 Series.
Related Information
&“Check Fax Connection” on page 257
&“Fax Setting Wizard” on page 257
&“Receive Settings” on page 257
&“Report Settings” on page 259
Product Information
>
Settings Menu List
>
General Settings
256
&“Basic Settings” on page 260
&“Security Settings” on page 262
Check Fax Connection
You can nd the menu on the printer's control panel below.
Settings > General Settings > Fax Settings > Check Fax Connection
Selecting Check Fax Connection checks that the printer is connected to the phone line and ready for fax
transmission. You can print the check result on A4 size plain paper.
Fax Setting Wizard
You c a n nd the menu on the printer's control panel below.
Settings > General Settings > Fax Settings > Fax Setting Wizard
Note:
You cannot display this menu on the Web Cong screen.
Selecting Fax Setting Wizard makes basic fax settings. Follow the on-screen instructions.
Related Information
&“Basic Settings” on page 260
&“Making the Printer Ready to Send and Receive Faxes” on page 286
Receive Settings
Related Information
&“Fax Output Settings” on page 257
&“Print Settings” on page 258
Fax Output Settings
You can nd the menu on the printer's control panel below.
Settings > General Settings > Fax Settings > Receive Settings > Fax Output Settings
Save to Inbox:
Save to Inbox:
Saves received faxes to the printer's Inbox. Up to 100 documents can be saved. Note that saving
100 documents may not be possible depending on the usage conditions such as the le size of
saved documents, and using of multiple fax saving features at a time.
ough the received faxes are not automatically printed, you can view them on the printer's
screen and print only the ones you need.
Product Information
>
Settings Menu List
>
General Settings
257
Options when memory is full:
You can select the operation to print the received fax or refuse to receive it when the Inbox
memory is full.
Inbox Password Settings:
Password protects the Inbox to restrict users from viewing received faxes. Select Change to
change the password, and select Reset to cancel password protection. When changing or
resetting the password, you need the current password.
You cannot set a password when Options when memory is full has been set to Receive and
print faxes.
Save to Computer:
Saves received faxes as PDF les on a computer connected to the printer. You can only set this to Yes
by using the FAX Utility (application). You cannot enable this from printer's control panel. Install the
FAX Utility on the computer in advance. Aer setting this to Yes, you can change this to Ye s an d
Print from the printer's control panel.
Related Information
&“Making Settings to Save Received Faxes” on page 289
Print Settings
You can nd the menu on the printer's control panel below.
Settings > General Settings > Fax Settings > Receive Settings > Print Settings
Auto Reduction:
Prints received faxes with large-size documents reduced to t on the paper in the paper source.
Reducing may not always be possible depending on the received data. If this is turned o, large
documents are printed at their original size on multiple sheets, or a blank second page may be
ejected.
Split Page Settings:
Prints received faxes with the page split when the size of the received documents is larger than the
size of the paper loaded in the printer.
Auto Rotation:
Rotates faxes received as landscape-oriented A5 size documents so that they are printed on A5 size
paper. is setting is applied when the paper size setting for at least one paper source used for
printing faxes is set to A5.
By selecting O, faxes received as landscape-oriented A5 size, which are the same width as A4
portrait documents, are assumed to be A4 size faxes and printed as such.
Check the paper size setting in Settings > General Settings > Printer Settings > Paper Source
Settings.
Add Reception Information:
Prints reception information on the received fax, even if the sender does not set the header
information. e reception information includes the received date and time, sender's ID, and page
number (such as "P1"). When Split Page Settings is enabled, the split page number is also included.
Product Information
>
Settings Menu List
>
General Settings
258
2-Sided:
Prints multiple pages of received faxes on both sides of the paper.
Print Start Timing:
Select options to start printing the faxes to receive.
❏All Pages Received: Printing starts aer receiving all of the pages. To start printing from the rst
page or last page depends on the setting of Collation Stack feature. See the explanation for
Collation Stack.
❏First Page Received: Starts printing when the rst page is received, and then prints in order as the
pages are received. If the printer cannot start printing, such as when it is printing other jobs, the
printer starts printing received pages as a batch when it is available.
Collation Stack:
Since the rst page is printed last (output to the top), the printed documents are stacked in the correct
page order. When the printer is running low on memory, this feature may not be available.
Print Suspend Time:
Print Suspend Time
During the specied time period, the printer saves documents received in the printer's
memory without printing them. is feature can be used for noise prevention at night or to
prevent condential documents from being disclosed while you are away. Before using this
feature, make sure there is enough free memory.
Time to Stop
Stops printing documents.
Time to Restart
Restarts printing documents automatically.
Quiet Mode:
Reduces the noise the printer makes when printing faxes, however, print speed may be reduced.
Report Settings
You can nd the menu on the printer's control panel below.
Settings > General Settings > Fax Settings > Report Settings
Fax Log Auto Print:
Prints the fax log automatically. Select On(Every 30) to print a log every time 30 fax jobs are
completed. Select On(Time) to print the log at a specied time. However, if the number of fax jobs
exceeds 30, the log is printed before the specied time.
Attach Fax image to report:
Prints a Transmission Report with an image of the rst page of the sent document. Select On(Large
Image) to print the upper part of the page without reducing. Select On(Small Image) to print the
entire page reducing it to t onto the report.
Product Information
>
Settings Menu List
>
General Settings
259
Report Format:
Selects a format for fax reports in Fax > More tab > Fax Report other than Protocol Trace. Select
Detail to print with error codes.
Basic Settings
You can nd the menu on the printer's control panel below.
Settings > General Settings > Fax Settings > Basic Settings
Fax Speed:
Select the fax transmission speed. We recommend selecting Slow(9,600bps) when a communication
error occurs frequently, when sending/receiving a fax to/from abroad, or when you are using an IP
(VoIP) phone service.
ECM:
Automatically corrects errors in the fax transmission (Error Correction Mode), mostly caused by
telephone line noise. If this is disabled, you cannot send or receive documents in color.
Dial Tone Detection:
Detects a dial tone before starting to dial. If the printer is connected to a PBX (Private Branch
Exchange) or digital phone line, the printer may fail to start dialing. In this situation, change the Line
Type setting to PBX. If this does not work, disable this feature. However, disabling this feature may
drop the rst digit of a fax number and send the fax to the wrong number.
Dial Mode:
Select the type of phone system to which you have connected the printer. When set to Pulse, you can
temporarily switch the dialing mode from pulse to tone by pressing ("T" is entered) while entering
numbers on the fax top screen. is setting may not be displayed depending on your region or
country.
Line Type:
Select the line type to which you have connected the printer.
When using the printer in an environment that uses extensions and requires an external access code,
such as 0 and 9, to get an outside line, select PBX. For an environment that uses a DSL modem or
terminal adapter, setting to PBX is also recommended.
Access Code
Select Use, and then register an external access code such as 0 or 9. en, when sending a fax
to an outside fax number, enter # (hash) instead of the real code. # (hash) must also be used in
Contacts as an external access code. If an external access code such as 0 or 9 is set in a contact,
you cannot send faxes to the contact. In this case, set Access Code to Do Not Use, otherwise
you must change the code in Contacts to #.
Header:
Enter your sender name and fax number. ese appear as a header on outgoing faxes.
❏Your Phone Number: You can enter up to 20 characters using 0-9 + or space. For Web Cong, you
can enter up to 30 characters.
Product Information
>
Settings Menu List
>
General Settings
260
❏Fax Header: You can register up to 21 sender names as necessary. You can enter up to 40 characters
for each sender name. For Web Cong, enter the header in Unicode (UTF-8).
Receive Mode:
Select the receive mode. For details, see the related Information below.
DRD:
If you have subscribed to a distinctive ring service from your telephone company, select the ring
pattern to be used for incoming faxes. e distinctive ring service, oered by many telephone
companies (the service name diers by company), allows you to have several phone numbers on one
phone line. Each number is assigned dierent ring pattern. You can use one number for voice calls
and another for fax calls. Depending on the region, this option may be On or O.
Rings to Answer:
Select the number of rings that must occur before the printer automatically receives a fax.
Remote Receive:
Remote Receive
When you answer an incoming fax call on a phone connected to the printer, you can start
receiving the fax by entering the code using the phone.
Start Code
Set the start code of Remote Receive. Enter two characters using 0-9, *, #.
Rejection Fax:
Rejection Fax
Select options to reject receiving junk faxes.
❏Rejection Number List: If the other party's phone number is in the rejection number list, set
whether to reject the incoming faxes.
❏Fax Header Blank: If the other party's phone number is blocked, set whether to reject
receiving the faxes.
❏Unregistered Contacts: If the other party's phone number is not in the contacts, set whether
to reject receiving the faxes.
Edit Blocked Number list
You can register up to 30 fax numbers to reject the faxes and calls. Enter up to 20 characters
using 0-9, *, #, or space.
Related Information
&“Making the Printer Ready to Send and Receive Faxes” on page 286
&“Making Settings for a PBX Phone System” on page 288
&“Receiving Incoming Faxes” on page 93
&“Making Settings for Blocking Junk Faxes” on page 290
Product Information
>
Settings Menu List
>
General Settings
261
Security Settings
You can nd the menu on the printer's control panel below.
Settings > General Settings > Fax Settings > Security Settings
Direct Dialing Restrictions:
Selecting On disables manual entry of the recipient's fax numbers allowing the operator to select
recipients only from the contacts list or sent history.
Selecting Enter Twice requires the operator to enter the fax number again when the number was
manually entered.
Selecting O enables manual entry of the recipient's fax numbers.
Conrm Address List:
Selecting On displays a recipient conrmation screen before starting the transmission.
Backup Data Auto Clear:
Backup copies of sent and received documents are usually temporarily stored in the printer's memory
to prepare for an unexpected power failure due to an electricity failure or incorrect operations.
Selecting On automatically erases the backups when sending or receiving a document completes
successfully and the backups become unnecessary.
Clear Backup Data:
Erases all backup copies temporarily stored in the printer's memory. Run this before you give the
printer to someone else or dispose of it.
Maintenance
Select the menus on the control panel as described below.
Settings > Maintenance
Print Head Nozzle Check:
Select this feature to check if the print head nozzles are clogged. e printer prints a nozzle check
pattern.
Print Head Cleaning:
Select this feature to clean clogged nozzles in the print head.
Power Cleaning:
Select this feature to replace all of the ink inside the ink tubes. More ink is consumed than in usual
cleaning. See the "Related Information" below for details on using this feature.
Print Head Alignment:
Select this feature to adjust the print head to improve print quality.
❏Vertical Alignment
Select this feature if your printouts look blurry or text and lines are misaligned.
Product Information
>
Settings Menu List
>
Maintenance
262
❏Horizontal Alignment
Select this feature if horizontal banding appears at regular intervals in your printouts.
Fill Ink:
Select this feature to reset the ink level to 100% when lling the ink tank.
Ink Level Setting:
Select this feature to set the ink level according to the actual ink remaining.
Remaining capacity of Maintenance box:
Displays the approximate service life of the maintenance box. When is displayed, the
maintenance box is nearly full. When is displayed, the maintenance box is full.
Paper Guide Cleaning:
Select this feature if there are ink stains on the internal rollers. e printer feeds paper to clean the
internal rollers.
Related Information
&“Checking and Cleaning the Print Head” on page 111
&“Running Power Cleaning” on page 112
&“Relling the Ink Tank” on page 193
&“Cleaning the Paper Path for Ink Smears” on page 114
Print Status Sheet
Select the menus on the control panel as described below.
Settings > Print Status Sheet
Conguration Status Sheet:
Print information sheets showing the current printer status and settings.
Supply Status Sheet:
Print information sheets showing the status of consumables.
Usage History Sheet:
Print information sheets showing the usage history of the printer.
Print Counter
Select the menus on the control panel as described below.
Settings > Print Counter
Displays the total number of prints, B&W prints, and color prints including items such as the status sheet from the
time you purchased the printer.
Product Information
>
Settings Menu List
>
Print Counter
263
User Settings
Select the menus on the control panel as described below.
Settings > User Settings
You can change the default settings for your frequently used scanning, copying, and faxing settings. See the
following related information for details.
❏Copy
❏Scan to Computer
❏Scan to Cloud
❏Fax
Restore Default Settings
Select the menus on the control panel as described below.
Settings > Restore Default Settings
Resets the following menus to their defaults.
❏Network Settings
❏Copy Settings
❏Scan Settings
❏Fax Settings
❏Clear All Data and Settings
Firmware Update
Select the menus on the control panel as described below.
Settings > Firmware Update
Update:
Check if the latest version of the rmware has been uploaded to the network server. e rmware is
updated when new rmware is found. Once the update has started, it cannot be interrupted.
Notication:
Select On to receive a notication if a rmware update is available.
Related Information
&“Updating the Printer's Firmware Using the Control Panel” on page 127
Product Information
>
Settings Menu List
>
Firmware Update
264
Product Specications
Printer Specications
Print Head Nozzle Placement Black ink nozzles: 400
Color ink nozzles: 128 for each color
Weight of Paper
*
Plain Paper 64 to 90 g/m(17 to 24lb)
Thick Paper 91 to 256 g/m (25 to 68 lb)
Envelopes Envelope #10, DL, C6: 75 to 100 g/m (20 to 27 lb)
* Even when the paper thickness is within this range, the paper may not feed in the printer or the print quality may decline
depending on the paper properties or quality.
Printable Area
Printable Area for Single Sheets
Print quality may decline in the shaded areas due to the printer's mechanism.
A 3.0 mm (0.12 in.)
B 3.0 mm (0.12 in.)
C 46.0 mm (1.81 in.)
D 44.0 mm (1.73 in.)
Printable Area for Envelopes
Print quality may decline in the shaded areas due to the printer's mechanism.
A 3.0 mm (0.12 in.)
B 3.0 mm (0.12 in.)
C 24.0 mm (0.95 in.)
D 46.0 mm (1.81 in.)
Scanner Specications
Scanner Type Flatbed
Product Information
>
Product Specications
>
Scanner Specications
265
Photoelectric Device CIS
Eective Pixels 10200×14040 pixels (1200 dpi)
Maximum Document Size 216×297 mm (8.5×11.7 in.)
A4, Letter
Scanning Resolution 1200 dpi (main scan)
2400 dpi (sub scan)
Output Resolution 50 to 9600 dpi in 1 dpi increments
Color Depth Color
❏48 bits per pixel internal (16 bits per pixel per color internal)
❏24 bits per pixel external (8 bits per pixel per color external)
Grayscale
❏16 bits per pixel internal
❏8 bits per pixel external
Black and white
❏16 bits per pixel internal
❏1 bits per pixel external
Light Source LED
ADF Specications
Available Paper Sizes A4, Letter, Legal, 8.5x13in
Paper Type Plain Paper
Weight of Paper 64 to 95 g/m(17 to 24lb)
Loading Capacity A4, Letter, : 35 sheets or 3.85 mm
Legal, 8.5x13in: 10 sheets
Auto Duplex Scanning Not supported
Even when the original meets the specications for media that can be placed in the ADF, it may not feed from the
ADF or the scan quality may decline depending on the paper properties or quality.
Fax Specications
ET-5170 Series/L6490 Series Only
Fax Type Walk-up black and white and color fax capability (ITU-T Super Group 3)
Supported Lines Standard analogue telephone lines, PBX (Private Branch Exchange) telephone
systems
Speed Up to 33.6 kbps
Product Information
>
Product Specications
>
Fax Specications
266
Resolution Monochrome
❏Standard: 8 pel/mm×3.85 line/mm (203 pel/in.×98 line/in.)
❏Fine: 8 pel/mm×7.7 line/mm (203 pel/in.×196 line/in.)
❏Super Fine: 8 pel/mm×15.4 line/mm (203 pel/in.×392 line/in.)
❏Ultra Fine: 16 pel/mm×15.4 line/mm (406 pel/in.×392 line/in.)
❏Photo: 8 pel/mm×7.7 line/mm (203 pel/in.×196 line/in.)
Color
❏Fine: 200×200 dpi
❏Photo: 200×200 dpi
Page Memory Up to 180 pages (when received ITU-T No.1 chart in monochrome draft mode)
Redial
*
2 times (with 1 minute intervals)
Interface RJ-11 Phone Line, RJ-11 Telephone set connection
* The specications may dier by country or region.
Using Port for the Printer
e printer uses the following port. ese ports should be allowed to become available by the network
administrator as necessary.
Sender
(Client)
Use Destination
(Server)
Protocol Port
Number
Printer When Epson Connect is used Epson Connect
Server
HTTPS 443
XMPP 5222
Control WSD Client computer WSD (TCP) 5357
Search the computer when push
scanning from Epson ScanSmart
Client computer Network Push Scan
Discovery
2968
Product Information
>
Product Specications
>
Using Port for the Printer
267
Sender
(Client)
Use Destination
(Server)
Protocol Port
Number
Client
computer
Discover the printer from an
application such as EpsonNet Cong,
printer driver, and scanner driver.
Printer ENPC (UDP) 3289
Collect and set up the MIB information
from an application such as EpsonNet
Cong, printer driver, and scanner
driver.
Printer SNMP (UDP) 161
Forwarding LPR data Printer LPR (TCP) 515
Forwarding RAW data Printer RAW (Port9100) (TCP) 9100
Forwarding AirPrint (IPP/IPPS printing)
data
Printer IPP/IPPS (TCP) 631
Searching WSD printer Printer WS-Discovery (UDP) 3702
Forwarding the scan data from Epson
ScanSmart
Printer Network Scan (TCP) 1865
Collecting the job information when
push scanning from Epson ScanSmart
Printer Network Push Scan 2968
Interface Specications
For Computer Hi-Speed USB
*
* USB 3.0 cables are not supported.
Network Specications
Wi-Fi Specications
Standards IEEE802.11b/g/n
*1
Frequency Range 2.4 GHz
Coordination Modes Infrastructure, Wi-Fi Direct (Simple AP)
*2*3
Wireless Securities
*4
WEP (64/128bit), WPA2-PSK (AES)
*5
*1 IEEE802.11n is only available for the HT20.
*2 Not supported for IEEE 802.11b.
*3 Simple AP mode is compatible with a Wi-Fi connection (infrastructure) or an Ethernet connection.
*4 Wi-Fi Direct supports WPA2-PSK (AES) only.
*5 Complies with WPA2 standards with support for WPA/WPA2 Personal.
Product Information
>
Product Specications
>
Network Specications
268
Ethernet Specications
Standards IEEE802.3i (10BASE-T)
*1
IEEE802.3u (100BASE-TX)
IEEE802.3az (Energy Ecient Ethernet)
*2
Communication Mode Auto, 10Mbps Full duplex, 10Mbps Half duplex, 100Mbps
Full duplex, 100Mbps Half duplex
Connector RJ-45
*1 Use a category 5e or higher STP (Shielded twisted pair) cable to prevent risk of radio interference.
*2 The connected device should comply with IEEE802.3az standards.
Network Functions and IPv4/IPv6
Functions Supported Remarks
Network Printing EpsonNet Print (Windows) IPv4 ✓-
Standard TCP/IP (Windows) IPv4, IPv6 ✓-
WSD Printing (Windows) IPv4, IPv6 ✓Windows Vista or
later
Bonjour Printing (Mac OS) IPv4, IPv6 ✓-
IPP Printing (Windows, Mac
OS)
IPv4, IPv6 ✓-
PictBridge Printing (Wi-Fi) IPv4 - Digital camera
Epson Connect (Email Print,
Remote Print)
IPv4 ✓-
AirPrint (iOS, Mac OS) IPv4, IPv6 ✓iOS 5 or later, Mac
OS X v10.7 or later
Network Scanning Epson Scan 2 IPv4, IPv6 ✓-
Epson ScanSmart IPv4 ✓Windows 7 or later,
Mac OS X El
Capitan or later
Event Manager IPv4 ✓Windows XP, Vista,
Mac OS X v10.6 to
Yosemite
Epson Connect (Scan to
Cloud)
IPv4 ✓-
AirPrint (Scan) IPv4, IPv6 ✓OS X Mavericks or
later
Product Information
>
Product Specications
>
Network Specications
269
Functions Supported Remarks
Fax Send a fax IPv4 ✓-
Receive a fax IPv4 ✓-
AirPrint (Faxout) IPv4, IPv6 ✓OS X Mountain
Lion or later
Security Protocol
SSL/TLS HTTPS Server/Client, IPPS
Supported Third Party Services
AirPrint Print iOS 5 or later/Mac OS X v10.7.x or later
Scan OS X Mavericks or later
Fax OS X Mountain Lion or later
Dimensions
Dimensions Storage
❏Width: 375 mm (14.8 in.)
❏Depth: 347 mm (13.7 in.)
❏Height: 346 mm (13.6 in.)
Printing
❏Width: 375 mm (14.8 in.)
❏Depth: 347 mm (13.7 in.)
❏Height: 346 mm (13.6 in.)
Weight
*
Approx. 7.3 kg (16.1 lb)
* Without the ink and the power cord.
Electrical Specications
ET-5170 Series/L6490 Series
Power Supply Rating AC 100-240 V AC 220-240 V
Rated Frequency Range 50-60 Hz 50-60 Hz
Rated Current 0.5-0.2 A 0.3 A
Product Information
>
Product Specications
>
Electrical Specications
270
Power Consumption (with USB Con-
nection)
Standalone copying: Approx. 12.0 W
(ISO/IEC24712)
Ready mode: Approx. 5.4 W
Sleep mode: Approx. 0.9 W
Power o: Approx. 0.2 W
Standalone copying: Approx. 12.0 W
(ISO/IEC24712)
Ready mode: Approx. 5.5 W
Sleep mode: Approx. 0.9 W
Power o: Approx. 0.2 W
Note:
❏Check the label on the printer for its voltage.
❏For European users, see the following Website for details on power consumption.
http://www.epson.eu/energy-consumption
ET-5150 Series/L6460 Series
Power Supply Rating AC 100-240 V AC 220-240 V
Rated Frequency Range 50-60 Hz 50-60 Hz
Rated Current 0.5-0.2 A 0.3 A
Power Consumption (with USB Con-
nection)
Standalone copying: Approx. 12.0 W
(ISO/IEC24712)
Ready mode: Approx. 5.3 W
Sleep mode: Approx. 0.9 W
Power o: Approx. 0.2 W
Standalone copying: Approx. 12.0 W
(ISO/IEC24712)
Ready mode: Approx. 5.4 W
Sleep mode: Approx. 0.9 W
Power o: Approx. 0.2 W
Note:
❏Check the label on the printer for its voltage.
❏For European users, see the following Website for details on power consumption.
http://www.epson.eu/energy-consumption
Environmental Specications
Operation Use the printer within the range shown in the following graph.
Temperature: 10 to 35°C (50 to 95°F)
Humidity: 20 to 80% RH (without condensation)
Storage Temperature after initial ink charging: -15 to 40°C (5 to 104°F)
*
Temperature before initial ink charging: -20 to 40°C (-4 to 104°F)
*
Humidity: 5 to 85% RH (without condensation)
Product Information
>
Product Specications
>
Environmental Specications
271
* You can store for one month at 40°C (104°F).
Environmental Specications for Ink Bottles
Storage Temperature -20 to 40 °C (-4 to 104 °F)
*
Freezing Temperature -15 °C (5 °F)
Ink thaws and is usable after approximately 2 hours at 25 °C (77 °F).
* You can store for one month at 40 °C (104 °F).
System Requirements
❏Windows
Windows Vista, Windows 7, Windows 8/8.1, Windows 10 or later (32-bit, 64-bit)
Windows XP SP3 (32-bit)
Windows XP Professional x64 Edition SP2
Windows Server 2003 (SP2) or later
❏Mac OS
Mac OS X v10.6.8 or later
Note:
❏Mac OS may not support some applications and features.
❏e UNIX File System (UFS) for Mac OS is not supported.
Regulatory Information
Standards and Approvals
Standards and Approvals for U.S. Model
Safety UL60950-1
CAN/CSA-C22.2 No.60950-1
EMC FCC Part 15 Subpart B Class B
CAN ICES-3 (B)/NMB-3 (B)
is equipment contains the following wireless module.
Manufacturer: Seiko Epson Corporation
Type: J26H006
is product conforms to Part 15 of the FCC Rules and RSS-210 of the IC Rules. Epson cannot accept
responsibility for any failure to satisfy the protection requirements resulting from a non-recommended
Product Information
>
Regulatory Information
>
Standards and Approvals
272
modication of the product. Operation is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation of the device.
To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from
windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject
to licensing.
is equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and
meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio
frequency (RF) Exposure rules. is equipment should be installed and operated so that the radiator is kept at least
7.9 inches (20 cm) or more away from a person's body (excluding extremities: hands, wrists, feet and ankles).
Standards and Approvals for European Model
For European users
Hereby, Seiko Epson Corporation declares that the following radio equipment model is in compliance with
Directive 2014/53/EU. e full text of the EU declaration of conformity is available at the following website.
http://www.epson.eu/conformity
C662B, C653A
For use only in Ireland, UK, Austria, Germany, Liechtenstein, Switzerland, France, Belgium, Luxemburg,
Netherlands, Italy, Portugal, Spain, Denmark, Finland, Norway, Sweden, Iceland, Croatia, Cyprus, Greece,
Slovenia, Malta, Bulgaria, Czech, Estonia, Hungary, Latvia, Lithuania, Poland, Romania, and Slovakia.
Epson cannot accept responsibility for any failure to satisfy the protection requirements resulting from a non-
recommended modication of the products.
Frequency Maximum Radio-Frequency Power Transmitted
2400-2483.5 MHz 20 dBm (EIRP)
Standards and Approvals for Australian Model
EMC AS/NZS CISPR32 Class B
Epson hereby declares that the following equipment Models are in compliance with the essential requirements and
other relevant provisions of AS/NZS4268:
C662B, C653A
Epson cannot accept responsibility for any failure to satisfy the protection requirements resulting from a non-
recommended modication of the products.
Standards and Approvals for New Zealand Model
General Warning
Product Information
>
Regulatory Information
>
Standards and Approvals
273
e grant of a Telepermit for any item of terminal equipment indicates only that Telecom has accepted that the
item complies with minimum conditions for connection to its network. It indicates no endorsement of the product
by Telecom, nor does it provide any sort of warranty. Above all, it provides no assurance that any item will work
correctly in all respects with another item of Telepermitted equipment of a dierent make or model, nor does it
imply that any product is compatible with all of Telecom's network services.
Telepermitted equipment only may be connected to the EXT telephone port. is port is not specically designed
for 3-wire-connected equipment. 3-wire-connected equipment might not respond to incoming ringing when
attached to this port.
Important Notice
Under power failure conditions, this telephone may not operate. Please ensure that a separate telephone, not
dependent on local power, is available for emergency use.
is equipment is not capable, under all operating conditions, of correct operation at the higher speeds for which it
is designed. Telecom will accept no responsibility should diculties arise in such circumstances.
is equipment shall not be set up to make automatic calls to the Telecom '111' Emergency Service.
Restrictions on Copying
Observe the following restrictions to ensure the responsible and legal use of the printer.
Copying of the following items is prohibited by law:
❏Bank bills, coins, government-issued marketable securities, government bond securities, and municipal
securities
❏Unused postage stamps, pre-stamped postcards, and other ocial postal items bearing valid postage
❏Government-issued revenue stamps, and securities issued according to legal procedure
Exercise caution when copying the following items:
❏Private marketable securities (stock certicates, negotiable notes, checks, etc.), monthly passes, concession
tickets, etc.
❏Passports, driver’s licenses, warrants of tness, road passes, food stamps, tickets, etc.
Note:
Copying these items may also be prohibited by law.
Responsible use of copyrighted materials:
Printers can be misused by improperly copying copyrighted materials. Unless acting on the advice of a
knowledgeable attorney, be responsible and respectful by obtaining the permission of the copyright holder before
copying published material.
Product Information
>
Regulatory Information
>
Restrictions on Copying
274
Connecting the Printer to the Network
You can connect the printer to the network in several ways.
❏Connect by using advanced settings on the control panel.
❏Connect by using the installer on the website or on the soware disc.
is section explains the procedure to connect the printer to the network using the printer's control panel.
Before Making Network Connection
To connect to the network, check the connection method and setting information for connection in advance.
Gathering Information on the Connection Setting
Prepare the necessary setting information to connect. Check the following information in advance.
Divisions Items Note
Device connection
method
❏Ethernet
❏Wi-Fi
Decide how to connect the printer to the network.
For Wired LAN, connects to the LAN switch.
For Wi-Fi, connects to the network (SSID) of the access point.
LAN connection
information
❏IP address
❏Subnet mask
❏Default gateway
Decide the IP address to assign to the printer.
When you assign the IP address statically, all values are required.
When you assign the IP address dynamically using the DHCP function,
this information is not required because it is set automatically.
Wi-Fi connection
information
❏SSID
❏Password
These are the SSID (network name) and the password of the access
point that the printer connects to.
If MAC address ltering has been set, register the MAC address of the
printer in advance to register the printer.
See the following for the supported standards.
“Wi-Fi Specications” on page 268
DNS server information ❏IP address for
primary DNS
❏IP address for
secondary DNS
These are required when specifying DNS servers. The secondary DNS
is set when the system has a redundant conguration and there is a
secondary DNS server.
If you are in a small organization and do not set the DNS server, set
the IP address of the router.
Proxy server
information
❏Proxy server name Set this when your network environment uses the proxy server to
access the internet from the intranet, and you use the function that
the printer directly accesses to the internet.
For the following functions, the printer directly connects to the
internet .
❏Epson Connect Services
❏Cloud services of other companies
❏Firmware updating
Administrator Information
>
Connecting the Printer to the Network
>
Before Making Network Connection
276
Divisions Items Note
Port number
information
❏Port number to
release
Check the port number used by the printer and computer, then
release the port that is blocked by a rewall, if necessary.
See the following for the port number used by the printer.
“Using Port for the Printer” on page 267
IP Address Assignment
ese are the following types of IP address assignment.
Static IP address:
Assign the predetermined IP address to the printer (host) manually.
e information to connect to the network (subnet mask, default gateway, DNS server and so on) need to be set
manually.
e IP address does not change even when the device is turned o, so this is useful when you want to manage
devices with an environment where you cannot change the IP address or you want to manage devices using the IP
address. We recommend settings to the printer, server, etc. that many computers access.
Automatic assignment by using DHCP function (dynamic IP address):
Assign the IP address automatically to the printer (host) by using the DHCP function of the DHCP server or
router.
e information to connect to the network (subnet mask, default gateway, DNS server and so on) is set
automatically, so you can easily connect the device to the network.
If the device or the router is turned o, or depending on the DHCP server settings, IP address may change when
re-connecting.
We recommend managing devices other than the IP address and communicating with protocols that can follow
the IP address.
Note:
When you use the IP address reservation function of the DHCP, you can assign the same IP address to the devices at any
time.
DNS Server and Proxy Server
e DNS server has a host name, domain name of the email address, etc. in association with the IP address
information.
Communication is impossible if the other party is described by host name, domain name, etc. when the computer
or the printer performs IP communication.
Queries the DNS server for that information and gets the IP address of the other party. is process is called name
resolution.
erefore, the devices such as computers and printers can communicate using the IP address.
Name resolution is necessary for the printer to communicate using the email function or Internet connection
function.
When you use those functions, make the DNS server settings.
Administrator Information
>
Connecting the Printer to the Network
>
Before Making Network Connection
277
When you assign the printer's IP address by using the DHCP function of the DHCP server or router, it is
automatically set.
e proxy server is placed at the gateway between the network and the Internet, and it communicates to the
computer, printer, and Internet (opposite server) on behalf of each of them. e opposite server communicates
only to the proxy server. erefore, printer information such as the IP address and port number cannot be read
and increased security is expected.
When you connect to the Internet via a proxy server, congure the proxy server on the printer.
Connecting to the Network from the Control Panel
Connect the printer to the network by using the printer's control panel.
Assigning the IP Address
Set up the basic items such as Host Address, Subnet Mask, Default Gateway.
is section explains the procedure for setting a static IP address.
1. Turn on the printer.
2. Select Settings on the home screen on the printer's control panel.
3. Select General Settings > Network Settings > Advanced > TCP/IP.
4. Select Manual for Obtain IP Address.
When you set the IP address automatically by using the DHCP function of router, select Auto. In that case, the
IP Address, Subnet Mask, and Default Gateway on step 5 to 6 are also set automatically, so go to step 7.
5. Enter the IP address.
Focus moves to the forward segment or the back segment separated by a period if you select
l
and
r
.
Conrm the value reected on the previous screen.
6. Set up the Subnet Mask and Default Gateway.
Conrm the value reected on the previous screen.
c
Important:
If the combination of the IP Address, Subnet Mask and Default Gateway is incorrect, Start Setup is inactive
and cannot proceed with the settings. Conrm that there is no error in the entry.
7. Enter the IP address for the primary DNS server.
Conrm the value reected on the previous screen.
Note:
When you select Auto for the IP address assignment settings, you can select the DNS server settings from Manual or
Auto. If you cannot obtain the DNS server address automatically, select Manual and enter the DNS server address.
en, enter the secondary DNS server address directly. If you select Auto, go to step 9.
Administrator Information
>
Connecting the Printer to the Network
>
Connecting to the Network from the
…
278
8. Enter the IP address for the secondary DNS server.
Conrm the value reected on the previous screen.
9. Tap Start Setup.
Setting the Proxy Server
Set up the proxy server if both of the following are true.
❏e proxy server is built for Internet connection.
❏When using a function in which a printer directly connects to the Internet, such as Epson Connect service or
another company's cloud services.
1. Select Settings on the home screen.
When making settings aer IP address setting, the Advanced screen is displayed. Go to step 3.
2. Select General Settings > Network Settings > Advanced.
3. Select Proxy Server.
4. Select Use for Proxy Server Settings.
5. Enter the address for the proxy server by IPv4 or FQDN format.
Conrm the value reected on the previous screen.
6. Enter the port number for the proxy server.
Conrm the value reected on the previous screen.
7. Tap Start Setup.
Connecting to LAN
Connect the printer to the network by Ethernet or Wi-Fi.
Connecting to Ethernet
Connect the printer to the network by using the Ethernet cable, and check the connection.
1. Connect the printer and hub (LAN switch) by Ethernet cable.
2. Select Settings on the home screen.
3. Select General Settings > Network Settings > Connection Check.
e connection diagnosis result is displayed. Conrm the connection is correct.
4. Tap OK to nish.
When you tap Print Check Report, you can print the diagnosis result. Follow the on-screen instructions to
print it.
Administrator Information
>
Connecting the Printer to the Network
>
Connecting to the Network from the
…
279
Related Information
&“Changing the Network Connection from Wi-Fi to Ethernet” on page 220
Connecting to the Wireless LAN (Wi-Fi)
You can connect the printer to the wireless LAN (Wi-Fi) in several ways. Choose the connection method that
matches the environment and conditions that you are using.
If you know the information for the wireless router such as SSID and password, you can make settings manually.
If the wireless router supports WPS, you can make settings by using push button setup.
Aer connecting the printer to the network, connect to the printer from the device that you want to use (computer,
smart device, tablet, and so on.)
Related Information
&“Making Wi-Fi Settings by Entering the SSID and Password” on page 222
&“Making Wi-Fi Settings by Push Button Setup (WPS)” on page 223
&“Making Wi-Fi Settings by PIN Code Setup (WPS)” on page 224
Settings to Use the Printer
Making Contacts Available
Registering a contacts list allows you to easily enter destinations. You can register up to 100 entries, and you can
use the contacts list when you enter a fax number. is feature is available only for ET-5170 Series/L6490 Series.
Registering or Editing Contacts
1. Select Fax on the home screen.
2. Select Contacts.
3. Do one of the following.
❏To register a new contact, select Add Entry, and then select Add Contact.
❏To edit a contact, select on the target contact, and then select Edit.
❏To delete a contact, select on the target contact, and then select Delete, and then select Yes. You do not
have to perform following procedures.
4. Make the necessary settings.
Note:
When entering a fax number, enter an external access code at the beginning of the fax number if your phone system is
PBX and you need the access code to get an outside line. If the access code has been set in the Line Type setting, enter a
hash (#) instead of the actual access code. To add a pause (pause for three seconds) during dialing, enter a hyphen (-).
5. Select OK.
Administrator Information
>
Settings to Use the Printer
>
Making Contacts Available
280
Registering or Editing Grouped Contacts
Adding contacts to a group allows you to send a fax to multiple destinations at the same time.
1. Select Fax on the home screen.
2. Select Contacts.
3. Do one of the following.
❏To register a new grouped contacts, select Add Entry, and then select Add Group.
❏To edit a grouped contacts, select on the target grouped contacts, and then select Edit.
❏To delete a grouped contacts, select on the target grouped contacts and then select Delete, and then
select Yes. You do not have to perform following procedures.
4. Enter or edit the Group Name and the Index Word, and then select Contact(s) Added to the Group
(Required).
5. Select the contacts that you want to register in the group, and then tap Close.
Note:
❏You can register up to 99 contacts.
❏To deselect a contact, tap it again.
6. Select OK.
Register Contacts on a Computer
Using Web Cong, you can create a contact list on your computer and import it to the printer.
1. Access Web Cong.
2. Select Advanced Settings from the list at the top right of the window.
3. Select Contacts.
4. Select the number that you want to register, and then click Edit.
5. Enter Name, Index Word, Fax Number, and Fax Speed.
6. Click Apply.
Related Information
&“Running Web Cong on a Web Browser” on page 249
Administrator Information
>
Settings to Use the Printer
>
Making Contacts Available
281
Destination Setting Items
Items Settings and Explanation
Name Enter a name displayed in the contacts in 30 characters or less in Unicode (UTF-8).
If you do not specify this, leave it blank.
Index Word Enter words to search in 30 characters or less in Unicode (UTF-8). If you do not
specify this, leave it blank.
Type This item is xed as Fax. You cannot change this setting.
Fax Number Enter between 1 and 64 characters using 0-9 - * # and space.
Fax Speed Select a communication speed for a destination.
Registering Destinations as a Group
1. Access Web Cong.
2. Select Advanced Settings from the list at the top right of the window.
3. Select Contacts.
4. Select the number that you want to register, and then click Edit.
5. Enter a Name and Index Word.
6. Select a group from Type.
7. Click Select for Contact(s) for Group.
e available destinations are displayed.
8. Select the destination that you want to register to the group, and then click Select.
Note:
Destinations can be registered to multiple groups.
9. Click Apply.
Related Information
&“Running Web Cong on a Web Browser” on page 249
Making Fax Features Available
Faxing feature is available only for ET-5170 Series/L6490 Series.
Before Using Fax Features
Set up the following to use the fax features.
Administrator Information
>
Settings to Use the Printer
>
Making Fax Features Available
282
❏Connect the printer correctly with the phone line and, if necessary, with a phone
❏Complete the Fax Setting Wizard, which is required to make basic settings.
Set the following as necessary.
❏Output destinations and related settings, such as network settings.
❏Contacts registration
❏User Settings that dene default values for Fax menu items
❏Report Settings to print reports when faxes are sent or received
Related Information
&“Connecting the Printer to a Phone Line” on page 283
&“Making the Printer Ready to Send and Receive Faxes” on page 286
&“Fax Settings” on page 256
&“Making Contacts Available” on page 280
&“User Settings” on page 264
&“Report Settings” on page 259
Connecting the Printer to a Phone Line
Compatible Telephone Lines
You can use the printer over standard analogue telephone lines (PSTN = Public Switched Telephone Network) and
PBX (Private Branch Exchange) telephone systems.
You may not be able to use the printer with the following phone lines or systems.
❏VoIP phone line such as DSL or ber-optic digital service
❏Digital phone line (ISDN)
❏Some PBX telephone systems
❏When adapters such as terminal adapters, VoIP adapters, splitters, or DSL router are connected between the
telephone wall jack and the printer
Connecting the Printer to a Phone Line
Connect the printer to a telephone wall jack using an RJ-11 (6P2C) phone cable. When connecting a telephone to
the printer, use a second RJ-11 (6P2C) phone cable.
Depending on the area, a phone cable may be included with the printer. If it is included, use that cable.
You may need to connect the phone cable to an adapter provided for your country or region.
Note:
Remove the cap from the EXT. port of the printer only when connecting your telephone to the printer. Do not remove the cap
if you are not connecting your telephone.
In areas where lightning strikes occur frequently, we recommend that you use a surge protector.
Administrator Information
>
Settings to Use the Printer
>
Making Fax Features Available
283
Connecting to a Standard Phone Line (PSTN) or PBX
Connect a phone cable from the telephone wall jack or PBX port to the LINE port on the back of the printer.
Connecting to DSL or ISDN
Connect a phone cable from the DSL modem or the ISDN terminal adapter to the LINE port on the back of the
printer. See the documentation provided with the modem or the adapter for more details.
Note:
If your DSL modem is not equipped with a built-in DSL lter, connect a separate DSL lter.
Connecting Your Phone Device to the Printer
When using the printer and your telephone on a single phone line, connect the telephone to the printer.
Note:
❏If your phone device has a fax function, disable the fax function before connecting. See the manuals that came with the
phone device for details. Depending on the model of the phone device, the fax function cannot be completely disabled, so
you may not be able to use it as an external phone.
❏If you connect an answering machine, make sure the printer's Rings to Answer setting is set higher than the number of
rings your answering machine is set to answer a call.
Administrator Information
>
Settings to Use the Printer
>
Making Fax Features Available
284
1. Remove the cap from the EXT. port on the back of the printer.
2. Connect the phone device and the EXT. port with a phone cable.
Note:
When sharing a single phone line, make sure you connect the phone device to the EXT. port of the printer. If you split
the line to connect the phone device and the printer separately, the phone and the printer do not work correctly.
3. Select Fax on the printer's control panel.
Administrator Information
>
Settings to Use the Printer
>
Making Fax Features Available
285
4. Pick up the handset.
If a message to start sending or receiving faxes is displayed as shown on the following screen, the connection
has been established.
Related Information
&“Making the Printer Ready to Send and Receive Faxes” on page 286
&“Making Settings to Use an Answering Machine” on page 289
&“Making Settings to Receive Faxes Operating Only a Connected Phone” on page 289
&“Receive Mode:” on page 261
Making the Printer Ready to Send and Receive Faxes
Fax Setting Wizard congures the basic fax features to make the printer ready to send and receive faxes.
e Wizard is displayed automatically when the printer is turned on for the rst time. You can also display the
wizard manually from the printer's control panel. You need to run the wizard again in case the wizard is skipped
when the printer is rst turned on or when the connection environment has changed.
❏e items below are what you can set through the wizard.
❏Header (Your Phone Number and Fax Header)
❏Receive Mode (Auto or Manual)
❏Distinctive Ring Detection (DRD) Setting
❏e items below are set automatically according to the connection environment.
❏Dial Mode (such as Tone or Pulse)
❏Other items in Basic Settings remain as they are.
Related Information
&“Basic Settings” on page 260
Making the Printer Ready to Send and Receive Faxes Using Fax Setting Wizard
1. Select Settings on the home screen on the printer's control panel.
Administrator Information
>
Settings to Use the Printer
>
Making Fax Features Available
286
2. Select General Settings > Fax Settings > Fax Setting Wizard.
3. Following the on-screen instructions, enter the sender name such as your company name, your fax number.
Note:
Your sender name and your fax number appear as the header for outgoing faxes.
4. Make the distinctive ring detection (DRD) setting.
❏If you have subscribed to a distinctive ring service from your telephone company:
Go to the next screen and select the ring pattern to be used for incoming faxes.
When you select any item except All, Receive Mode is set to Auto and you continue to the next screen
where you can check the settings you made.
❏If you have not subscribed to a distinctive ring service from your telephone company, or you do not need to
set this option:
Skip this setting and go to the screen where you can check the settings you made.
Note:
❏Distinctive ring services, oered by many telephone companies (the service name diers by company), allows you to
have several phone numbers on one phone line. Each number is assigned a dierent ring pattern. You can use one
number for voice calls and another for fax calls. Select the ring pattern assigned to fax calls in DRD.
❏Depending on the region, On and O are displayed as the DRD options. Select On to use the distinctive ring feature.
5. Make the Receive Mode setting.
❏If you do not need to connect a phone device to the printer:
Select No.
Receive Mode is set to Auto.
❏If you need to connect a phone device to the printer:
Select Yes , and then select whether or not to receive faxes automatically.
6. Check the settings you made on the screen displayed, and then proceed to the next screen.
To correct or change settings, select .
7. Check the fax connection by selecting Start Checking, and then select Print to print a report that shows the
connection status.
Note:
❏If there are any errors reported, follow the instructions on the report to solve them.
❏If the Select Line Type screen is displayed, select the line type.
- When you are connecting the printer to a PBX phone system or terminal adapter, select PBX.
- When you are connecting the printer to a standard phone line, select PSTN, and then select Do Not Detect on the
Conrmation screen displayed. However, setting this to Do Not Detect may cause the printer to skip the rst digit of
a fax number when dialing and send the fax to the wrong number.
Related Information
&“Connecting the Printer to a Phone Line” on page 283
&“Making Settings to Use an Answering Machine” on page 289
&“Receive Mode:” on page 261
&“Making Settings to Receive Faxes Operating Only a Connected Phone” on page 289
Administrator Information
>
Settings to Use the Printer
>
Making Fax Features Available
287
&“Basic Settings” on page 260
Making Settings for the Printer's Fax Features According to Use
You can congure the printer's fax features individually using the printer's control panel according to use. e
settings made using Fax Setting Wizard can also be changed. For more details, see the descriptions of the Fax
Settings menu.
Related Information
&“Fax Settings” on page 256
&“Making Settings for a PBX Phone System” on page 288
&“Making Settings When You Connect a Phone Device” on page 289
&“Receiving Incoming Faxes” on page 93
&“Making Settings to Save Received Faxes” on page 289
&“Making Settings for Blocking Junk Faxes” on page 290
&“Making Settings to Send and Receive Faxes on a Computer” on page 291
Making Settings for a PBX Phone System
Make the following settings when using the printer in oces that use extensions and require external access codes,
such as 0 and 9, to get an outside line.
1. Select Settings on the printer's control panel.
2. Select General Settings > Fax Settings > Basic Settings.
3. Select Line Type, and then select PBX.
4. When sending a fax to an outside fax number using # (hash) instead of the actual external access code, select
the Access Code box to make this to Use.
e #, entered instead of the actual access code, is replaced with the stored access code when dialing. Using #
helps avoid connection problems when connecting to an outside line.
Note:
You cannot send faxes to recipients in Contacts that have external access codes such as 0 and 9.
If you have registered recipients in Contacts using an external access code such as 0 and 9, set the Access Code to Do
Not Use. Otherwise, you must change the code to # in Contacts.
5. Tap the Access Code input box, enter the external access code used for your phone system, and then tap OK.
6. Select OK to apply the settings.
e access code is stored in the printer.
Administrator Information
>
Settings to Use the Printer
>
Making Fax Features Available
288
Making Settings When You Connect a Phone Device
Making Settings to Use an Answering Machine
You need settings to use an answering machine.
1. Select Settings on the printer's control panel..
2. Select General Settings > Fax Settings > Basic Settings.
3. Set Receive Mode to Auto.
4. Set the Rings to Answer setting of the printer to a higher number than the number of rings for the answering
machine.
If Rings to Answer is set lower than the number of rings for the answering machine, the answering machine
cannot receive voice calls to record voice messages. See the manuals that came with the answering machine for
its settings.
e printer's Rings to Answer setting may not be displayed, depending on the region.
Related Information
&“Basic Settings” on page 260
Making Settings to Receive Faxes Operating Only a Connected Phone
You can start receiving incoming faxes by only picking up the handset and operating the phone, without operating
the printer at all.
e Remote Receive feature is available for telephones that support tone dialing.
1. Select Settings on the printer's control panel.
2. Select General Settings > Fax Settings > Basic Settings > Remote Receive.
3. Tap Remote Receive to set this to On.
4. Select Start Code, enter a two digit code (you can enter 0 to 9, *, and #), and then tap OK.
5. Select OK to apply the settings.
Related Information
&“Basic Settings” on page 260
Making Settings to Save Received Faxes
e printer is set to print received faxes by default. Besides printing, you can set the printer to save received faxes.
❏Inbox in the Printer
You can save received faxes to the Inbox. You can view them on the printer's control panel so that you can print
only the ones you want to print or delete unnecessary faxes.
Administrator Information
>
Settings to Use the Printer
>
Making Fax Features Available
289
❏A computer (PC-FAX reception)
e above features can be used at the same time. If you use them at the same time, received documents are saved
to the inbox and on a computer. To receive faxes on a computer, make settings using FAX Utility.
“Making Settings to Send and Receive Faxes on a Computer” on page 291
1. Select Settings on the printer's control panel.
2. Select General Settings > Fax Settings > Receive Settings > Fax Output Settings.
3. If a conrmation message is displayed, conrm it, and then tap OK.
4. Select Save to Inbox.
5. Select Save to Inbox to set this to On
6. Select Options when memory is full, select the option to use when the inbox is full.
❏Receive and print faxes: e printer prints all received documents that cannot be saved in the Inbox.
❏Reject incoming faxes: e printer does not answer incoming fax calls.
7. You can s e t a p a s s word for the inb ox . S elect Inbox Password Settings, and then set the password.
Note:
You cannot set a password when Options when memory is full is set to Receive and print faxes.
Related Information
&“Fax Output Settings” on page 257
&“Viewing Received Faxes Saved in the Printer on the LCD Screen” on page 95
Making Settings for Blocking Junk Faxes
You can block junk faxes.
1. Select Settings on the printer's control panel.
2. Select General Settings > Fax Settings > Basic Settings > Rejection Fax.
3. Set the condition to block junk faxes.
Select Rejection Fax, and then enable the following options.
❏Rejection Number List: Rejects faxes that are in the Rejection Number List.
❏Fax Header Blank: Rejects faxes that have blank header information.
❏Unregistered Contacts: Rejects faxes that have not been added to the contact list.
4. Tap to return to the Rejection Fax screen.
5. If you are using the Rejection Number List, select Edit Blocked Number list, and then edit the list.
Administrator Information
>
Settings to Use the Printer
>
Making Fax Features Available
290
Making Settings to Send and Receive Faxes on a Computer
To send and receive faxes on a computer, FAX Utility must be installed on the computer connected by network or
USB cable .
Making Save to Computer Setting to Receive Faxes
You can receive faxes on a computer by using the FAX Utility. Install FAX Utility on the computer
and make the setting. For details, see Basic Operations in the FAX Utility help (displayed on the main
window).
e setting item below on the printer's control panel is set to Yes, and the faxes received can be saved
on the computer.
Settings > General Settings > Fax Settings > Receive Settings > Fax Output Settings > Save to
Computer
Making Save to Computer Setting to Also Print on the Printer to Receive Faxes
You can make the setting to print received faxes on the printer as well as save them on a computer.
1. Select Settings on the home screen on the printer's control panel.
2. Select General Settings > Fax Settings > Receive Settings.
3. Select Fax Output Settings > Save to Computer > Ye s and Pri nt.
Making Save to Computer Setting not to Receive Faxes
To set the printer not to save received faxes on the computer, change the settings on the printer.
Note:
You can also change the settings using the FAX Utility. However, if there are any faxes that have been unsaved
to the computer, the feature does not work.
1. Select Settings on the home screen on the printer's control panel.
2. Select General Settings > Fax Settings > Receive Settings.
3. Select Fax Output Settings > Save to Computer > No.
Related Information
&“Running Web Cong on a Web Browser” on page 249
Problems when Making Settings
Hints to Solving Problems
❏Checking the error message
When trouble has occurred, rst check whether there are any messages on the printer's control panel or driver
screen. If you have the notication email set when the events occur, you can promptly learn the status.
Administrator Information
>
Settings to Use the Printer
>
Problems when Making Settings
291
❏Network connection report
Diagnose the network and the printer status, and then print the result.
You can nd the diagnosed error from the printer side.
❏Checking the communication status
Check the communication status of server computer or client computer by using the command such as ping
and ipcong.
❏Connection test
For checking the connection between the printer to the mail server, perform the connection test from the
printer. Also, check the connection from the client computer to the server to check the communication status.
❏Initializing the settings
If the settings and communication status show no problem, the problems may be solved by disabling or
initializing the network settings of the printer, and then setting up again.
Cannot Access Web Cong
The IP address is not assigned to the printer.
A valid IP address may not be assigned to the printer. Congure the IP address using the printer’s
control panel. You can conrm the current setting information with a network status sheet or from
the printer’s control panel.
Web browser does not support the Encryption Strength for SSL/TLS.
SSL/TLS has the Encryption Strength. You can open Web Cong by using a web browser that
supports bulk encryptions as indicated below. Check you are using the a supported browser.
❏80bit: AES256/AES128/3DES
❏112bit: AES256/AES128/3DES
❏128bit: AES256/AES128
❏192bit: AES256
❏256bit: AES256
CA-signed Certicate is expired.
If there is a problem with the expiration date of the certicate, "e certicate has expired" is
displayed when connecting to Web Cong with SSL/TLS communication (https). If the message
appears before its expiration date, make sure that the printer's date is congured correctly.
The common name of the certicate and the printer do not match.
If the common name of the certicate and the printer do not match, the message "e name of the
security certicate does not match···" is displayed when accessing Web Cong using SSL/TLS
communication (https). is happens because the following IP addresses do not match.
❏e printer's IP address entered to common name for creating a Self-signed Certicate or CSR
❏IP address entered to web browser when running Web Cong
For Self-signed Certicate, update the certicate.
For CA-signed Certicate, take the certicate again for the printer.
Administrator Information
>
Settings to Use the Printer
>
Problems when Making Settings
292
The proxy server setting of local address is not set to web browser.
When the printer is set to use a proxy server, congure the web browser not to connect to the local
address via the proxy server.
❏Windows:
Select Control Panel > Network and Internet > Internet Options > Connections > LAN settings
> Proxy server, and then congure not to use the proxy server for LAN (local addresses).
❏Mac OS:
Select System Preferences > Network > Advanced > Proxies, and then register the local address
for Bypass proxy settings for these Hosts & Domains.
Example:
192.168.1.*: Local address 192.168.1.XXX, subnet mask 255.255.255.0
192.168.*.*: Local address 192.168.XXX.XXX, subnet mask 255.255.0.0
Administrator Information
>
Settings to Use the Printer
>
Problems when Making Settings
293
Technical Support Web Site
If you need further help, visit the Epson support website shown below. Select your country or region and go to the
support section of your local Epson website. e latest drivers, FAQs, manuals, or other downloadables are also
available from the site.
http://support.epson.net/
http://www.epson.eu/support (Europe)
If your Epson product is not operating properly and you cannot solve the problem, contact Epson support services
for assistance.
Contacting Epson Support
Before Contacting Epson
If your Epson product is not operating properly and you cannot solve the problem using the troubleshooting
information in your product manuals, contact Epson support services for assistance.
e following Epson support list is based on the country of sale. Some products may not be sold in your current
location, so be sure to contact Epson support for the area in which you purchased your product.
If Epson support for your area is not listed below, contact the dealer where you purchased your product.
Epson support will be able to help you much more quickly if you give them the following information:
❏Product serial number
(e serial number label is usually on the back of the product.)
❏Product model
❏Product soware version
(Click About, Version Info, or a similar button in the product soware.)
❏Brand and model of your computer
❏Your computer operating system name and version
❏Names and versions of the soware applications you normally use with your product
Note:
Depending on the product, the dial list data for fax and/or network settings may be stored in the product’s memory. Due to
breakdown or repair of a product, data and/or settings may be lost. Epson shall not be responsible for the loss of any data, for
backing up or recovering data and/or settings even during a warranty period. We recommend that you make your own
backup data or take notes.
Help for Users in Europe
Check your Pan-European Warranty Document for information on how to contact Epson support.
Help for Users in Taiwan
Contacts for information, support, and services are:
Where to Get Help
>
Contacting Epson Support
>
Help for Users in Taiwan
295
World Wide Web
http://www.epson.com.tw
Information on product specications, drivers for download, and products enquiry are available.
Epson HelpDesk
Phone: +886-2-80242008
Our HelpDesk team can help you with the following over the phone:
❏Sales enquiries and product information
❏Product usage questions or problems
❏Enquiries on repair service and warranty
Repair service center:
http://www.tekcare.com.tw/branchMap.page
TekCare corporation is an authorized service center for Epson Taiwan Technology & Trading Ltd.
Help for Users in Australia
Epson Australia wishes to provide you with a high level of customer service. In addition to your product manuals,
we provide the following sources for obtaining information:
Internet URL
http://www.epson.com.au
Access the Epson Australia World Wide Web pages. Worth taking your modem here for the occasional surf! e
site provides a download area for drivers, Epson contact points, new product information and technical support (e-
mail).
Epson Helpdesk
Phone: 1300-361-054
Epson Helpdesk is provided as a nal backup to make sure our clients have access to advice. Operators on the
Helpdesk can aid you in installing, conguring and operating your Epson product. Our Pre-sales Helpdesk sta
can provide literature on new Epson products and advise where the nearest dealer or service agent is located. Many
types of queries are answered here.
We encourage you to have all the relevant information on hand when you ring. e more information you prepare,
the faster we can help solve the problem. is information includes your Epson product manuals, type of
computer, operating system, application programs, and any information you feel is required.
Transportation of Product
Epson recommends retaining product packaging for future transportation. Securing the ink tank with tape and
keeping the product upright is also recommended.
Help for Users in New Zealand
Epson New Zealand wishes to provide you with a high level of customer service. In addition to your product
documentation, we provide the following sources for obtaining information:
Where to Get Help
>
Contacting Epson Support
>
Help for Users in New Zealand
296
Internet URL
http://www.epson.co.nz
Access the Epson New Zealand World Wide Web pages. Worth taking your modem here for the occasional surf!
e site provides a download area for drivers, Epson contact points, new product information and technical
support (e-mail).
Epson Helpdesk
Phone: 0800 237 766
Epson Helpdesk is provided as a nal backup to make sure our clients have access to advice. Operators on the
Helpdesk can aid you in installing, conguring and operating your Epson product. Our Pre-sales Helpdesk sta
can provide literature on new Epson products and advise where the nearest dealer or service agent is located. Many
types of queries are answered here.
We encourage you to have all the relevant information on hand when you ring. e more information you prepare,
the faster we can help solve the problem. is information includes your Epson product documentation, type of
computer, operating system, application programs, and any information you feel is required.
Transportation of Product
Epson recommends retaining product packaging for future transportation. Securing the ink tank with tape and
keeping the product upright is also recommended.
Help for Users in Singapore
Sources of information, support, and services available from Epson Singapore are:
World Wide Web
http://www.epson.com.sg
Information on product specications, drivers for download, Frequently Asked Questions (FAQ), Sales Enquiries,
and Technical Support via e-mail are available.
Epson HelpDesk
Toll Free: 800-120-5564
Our HelpDesk team can help you with the following over the phone:
❏Sales enquiries and product information
❏Product usage questions or problem troubleshooting
❏Enquiries on repair service and warranty
Help for Users in Thailand
Contacts for information, support, and services are:
World Wide Web
http://www.epson.co.th
Information on product specications, drivers for download, Frequently Asked Questions (FAQ), and e-mail are
available.
Where to Get Help
>
Contacting Epson Support
>
Help for Users in Thailand
297
Epson Call Centre
Phone: 66-2685-9899
Email: support@eth.epson.co.th
Our Call Centre team can help you with the following over the phone:
❏Sales enquiries and product information
❏Product usage questions or problems
❏Enquiries on repair service and warranty
Help for Users in Vietnam
Contacts for information, support, and services are:
Epson Service Center
65 Truong Dinh Street, District 1, Ho Chi Minh City, Vietnam.
Phone(Ho Chi Minh City): 84-8-3823-9239, 84-8-3825-6234
29 Tue Tinh, Quan Hai Ba Trung, Hanoi City, Vietnam
Phone(Hanoi City): 84-4-3978-4785, 84-4-3978-4775
Help for Users in Indonesia
Contacts for information, support, and services are:
World Wide Web
http://www.epson.co.id
❏Information on product specications, drivers for download
❏Frequently Asked Questions (FAQ), Sales Enquiries, questions through e-mail
Epson Hotline
Phone: +62-1500-766
Fax: +62-21-808-66-799
Our Hotline team can help you with the following over the phone or fax:
❏Sales enquiries and product information
❏Technical support
Where to Get Help
>
Contacting Epson Support
>
Help for Users in Indonesia
298
Epson Service Center
Province Company Name Address Phone
E-mail
JAKARTA Epson Sales and
Service Jakarta
(SUDIRMAN)
Wisma Keiai Lt. 1 Jl. Jenderal Sudirman Kav.
3 Jakarta Pusat - DKI JAKARTA 10220
021-5724335
ess@epson-indonesia.co.id;
ess.support@epson-
indonesia.co.id
SERPONG Epson Sales and
Service Serpong
Ruko Melati Mas Square Blok A2 No.17
Serpong-Banten
082120090084 / 082120090085
esstag@epson-indonesia.co.id;
esstag.support@epson-
indonesia.co.id
SEMARANG Epson Sales and
Service Semarang
Komplek Ruko Metro Plaza Block C20 Jl. MT
Haryono No. 970 Semarang -JAWA TENGAH
024 8313807 / 024 8417935
esssmg@epson-indonesia.co.id;
esssmg.support@epson-
indonesia.co.id
JAKARTA Epson Sales and
Service Jakarta
(MANGGA DUA)
Ruko Mall Mangga Dua No. 48 Jl. Arteri
Mangga Dua, Jakarta Utara - DKI JAKARTA
021 623 01104
jkt-technical1@epson-
indonesia.co.id; jkt-admin@epson-
indonesia.co.id
BANDUNG Epson Sales and
Service Bandung
Jl. Cihampelas No. 48 A Bandung Jawa
Barat 40116
022 420 7033
bdg-technical@epson-
indonesia.co.id; bdg-
admin@epson-indonesia.co.id
MAKASSAR Epson Sales and
Service Makassar
Jl. Cendrawasih NO. 3A, kunjung mae,
mariso, MAKASSAR - SULSEL 90125
0411- 8911071
mksr-technical@epson-
indonesia.co.id; mksr-
admin@epson-indonesia.co.id
MEDAN Epson Service
Center Medan
Jl. Bambu 2 Komplek Graha Niaga Nomor
A-4, Medan - SUMUT
061- 42066090 / 42066091
mdn-technical@epson-
indonesia.co.id; mdn-adm@epson-
indonesia.co.id
PALEMBANG Epson Service
Center Palembang
Jl. H.M Rasyid Nawawi No. 249 Kelurahan 9
Ilir Palembang Sumatera Selatan
0711 311 330
escplg@epson-indonesia.co.id;
escplg.support@epson-
indonesia.co.id
PEKANBARU Epson Service
Center PekanBaru
Jl. Tuanku Tambusai No. 459 A Kel.
Tangkerang barat Kec Marpoyan damai
Pekanbaru - Riau 28282
0761- 8524695
pkb-technical@epson-
indonesia.co.id; pkb-
admin@epson-indonesia.co.id
PONTIANAK Epson Service
Center Pontianak
Komp. A yani Sentra Bisnis G33, Jl. Ahmad
Yani - Pontianak Kalimantan Barat
0561- 735507 / 767049
pontianak-technical@epson-
indonesia.co.id; pontianak-
admin@epson-indonesia.co.id
Where to Get Help
>
Contacting Epson Support
>
Help for Users in Indonesia
299
Province Company Name Address Phone
E-mail
SAMARINDA Epson Service
Center Samarinda
Jl. KH. Wahid Hasyim (M. Yamin) Kelurahan
Sempaja Selatan Kecamatan Samarinda
UTARA - SAMARINDA - KALTIM
0541 7272 904
escsmd@epson-indonesia.co.id;
escsmd.support@epson-
indonesia.co.id
SURABAYA Epson Sales &
Service Surabaya
(barat)
Jl. Haji Abdul Wahab Saimin, Ruko Villa
Bukit Mas RM-11, Kec. Dukuh Pakis,
Surabaya - 60225
031- 5120994
sby-technical@epson-
indonesia.co.id; sby-
admin@epson-indonesia.co.id
YOGYAKARTA Epson Service
Center Yogyakarta
YAP Square, Block A No. 6 Jl. C Simanjutak
Yogyakarta - DIY
0274 581 065
ygy-technical@epson-
indonesia.co.id; ygy-
admin@epson-indonesia.co.id
JEMBER Epson Service
Center Jember
JL. Panglima Besar Sudirman Ruko no.1D
Jember-Jawa Timur (Depan Balai Penelitian
& Pengolahan Kakao)
0331- 488373 / 486468
jmr-admin@epson-indonesia.co.id;
jmr-technical@epson-
indonesia.co.id
MANADO EPSON SALES AND
SERVICE Manado
Jl. Piere Tendean Blok D No 4 Kawasan
Mega Mas Boulevard - Manado 95111
0431- 8805896
MND-ADMIN@EPSON-
INDONESIA.CO.ID; MND-
TECHNICAL@EPSON-
INDONESIA.CO.ID
CIREBON EPSON SERVICE
CENTER Cirebon
Jl. Tuparev No. 04 ( Depan Hotel Apita )
Cirebon, JAWA BARAT
0231– 8800846
cbn-technical@epson-
indonesia.co.id
CIKARANG EPSON SALES AND
SERVICE CIKARANG
Ruko Metro Boulevard B1 Jababeka
cikarang - Jawa Barat,
021- 89844301 / 29082424
ckg-admin@epson-
indonesia.co.id; ckg-
technical@epson-indonesia.co.id
MADIUN EPSON SERVICE
CENTER MADIUN
Jl. Diponegoro No.56, MADIUN - JAWA
TIMUR
0351- 4770248
mun-admin@epson-
indonesia.co.id ; mun-
technical@epson-indonesia.co.id
PURWOKERTO EPSON SALES AND
SERVICE Purwokerto
Jl. Jendral Sudirman No. 4 Kranji
Purwokerto - JAWA TENGAH
0281- 6512213
pwt-admin@epson-
indonesia.co.id ; pwt-
technical@epson-indonesia.co.id
BOGOR EPSON SALES AND
SERVICE Bogor
Jl.Pajajaran No 15B Kel Bantarjati Kec Bogor
Utara - JAWA BARAT 16153
0251- 8310026
bgr-admin@epson-
indonesia.co.id ; bgr-
technical@epson-indonesia.co.id
SERANG EPSON SERVICE
CENTER Serang
Jl. Ahmad Yani No.45C, SERANG - BANTEN 0254- 7912503
srg-admin@epson-
indonesia.co.id ; srg-
technical@epson-indonesia.co.id
Where to Get Help
>
Contacting Epson Support
>
Help for Users in Indonesia
300
Province Company Name Address Phone
E-mail
PALU EPSON SALES AND
SERVICE Palu
Jl. Juanda No. 58, Palu - Sulteng 0451- 4012 881
plw-admin@epson-
indonesia.co.id; plw-
technical@epson-indonesia.co.id
BANJARMASI
N
EPSON SERVICE
CENTER
BANJARMASIN
Jl. Gatot Soebroto NO. 153 BANJARMASIN -
KALSEL 70235
0511- 6744135 (TEKNISI) /
3266321(ADMIN)
bdj-admin@epson-indonesia.co.id;
bdj-technical@epson-
indonesia.co.id
DENPASAR EPSON SALES AND
SERVICE Denpasar
JL. MAHENDRADATA NO. 18, DENPASAR -
BALI
0361- 3446699 / 9348428
dps-admin@epson-
indonesia.co.id; dps-
technical@epson-indonesia.co.id
JAKARTA EPSON SALES AND
SERVICE CILANDAK
CIBIS Business Park Tower 9 LT. MEZZANINE,
Jalan TB Simatupang No.2, Jakarta Selatan -
DKI JAKARTA 12560
021- 80866777
esscibis.support1@epson-
indonesia.co.id;
esscibis.support2@epson-
indonesia.co.id;
esscibis.admin@epson-
indonesia.co.id;
esscibis.sales@epson-
indonesia.co.id
SURABAYA EPSON SALES AND
SERVICE SURABAYA
(GUBENG)
JL. RAYA GUBENG NO. 62, SURABAYA - JAWA
TIMUR
031- 99444940 / 99446299 /
99446377
esssby@epson-indonesia.co.id;
esssby.support@epson-
indonesia.co.id
AMBON EPSON SERVICE
CENTER AMBON
Jl. Diponegoro No.37 (Samping Bank
Mandiri Syariah) Kel.Ahusen, Kec.Sirimau -
Ambon 97127
-
For other cities not listed here, call the Hot Line: 08071137766.
Help for Users in Hong Kong
To obtain technical support as well as other aer-sales services, users are welcome to contact Epson Hong Kong
Limited.
Internet Home Page
http://www.epson.com.hk
Epson Hong Kong has established a local home page in both Chinese and English on the Internet to provide users
with the following information:
❏Product information
❏Answers to Frequently Asked Questions (FAQs)
Where to Get Help
>
Contacting Epson Support
>
Help for Users in Hong Kong
301
❏Latest versions of Epson product drivers
Technical Support Hotline
You can also contact our technical sta at the following telephone and fax numbers:
Phone: 852-2827-8911
Fax: 852-2827-4383
Help for Users in Malaysia
Contacts for information, support, and services are:
World Wide Web
http://www.epson.com.my
❏Information on product specications, drivers for download
❏Frequently Asked Questions (FAQ), Sales Enquiries, questions through e-mail
Epson Call Centre
Phone: 1800-81-7349 (Toll Free)
Email: websupport@emsb.epson.com.my
❏Sales enquiries and product information
❏Product usage questions or problems
❏Enquiries on repair services and warranty
Head Oce
Phone: 603-56288288
Fax: 603-5628 8388/603-5621 2088
Help for Users in India
Contacts for information, support, and services are:
World Wide Web
http://www.epson.co.in
Information on product specications, drivers for download, and products enquiry are available.
Helpline
❏Service, product information, and ordering consumables (BSNL Lines)
Toll-free number: 18004250011
Accessible 9am to 6pm, Monday through Saturday (Except public holidays)
Where to Get Help
>
Contacting Epson Support
>
Help for Users in India
302
❏Service (CDMA & Mobile Users)
Toll-free number: 186030001600
Accessible 9am to 6pm, Monday through Saturday (Except public holidays)
Help for Users in the Philippines
To obtain technical support as well as other aer sales services, users are welcome to contact the Epson Philippines
Corporation at the telephone, fax numbers and e-mail address below:
World Wide Web
http://www.epson.com.ph
Information on product specications, drivers for download, Frequently Asked Questions (FAQ), and E-mail
Enquiries are available.
Epson Philippines Customer Care
Toll Free: (PLDT) 1-800-1069-37766
Toll Free: (Digital) 1-800-3-0037766
Metro Manila: (632) 8441 9030
Web Site: https://www.epson.com.ph/contact
E-mail: customercare@epc.epson.com.ph
Accessible 9am to 6pm, Monday through Saturday (Except public holidays)
Our Customer Care team can help you with the following over the phone:
❏Sales enquiries and product information
❏Product usage questions or problems
❏Enquiries on repair service and warranty
Epson Philippines Corporation
Trunk Line: +632-706-2609
Fax: +632-706-2663
Where to Get Help
>
Contacting Epson Support
>
Help for Users in the Philippines
303