Table of Contents
- Contents
- Introduction to Your Projector
- Setting Up the Projector
- Using the Projector on a Network
- Wired Network Projection
- Wireless Network Projection
- Setting Up Projector Network E-Mail Alerts
- Selecting Other Network Settings
- Setting a Static IP Address on the LCD Screen
- Controlling a Networked Projector Using a Web Browser
- Using Crestron Connected
- Art-Net Channel Definitions
- Registering a Digital Certificate on the Projector
- Using Basic Projector Features
- Turning On the Projector
- Turning Off the Projector
- Selecting the Language for the Projector Menus
- Adjusting the Image Height
- Resizing the Image with the Zoom Button
- Focusing the Image Using the Focus and Distortion Buttons
- Setting the Screen Type
- Adjusting the Image Position Using Lens Shift
- Adjusting the Image Position Using Screen Position
- Displaying a Test Pattern
- Image Shape
- Selecting an Image Source
- Remote Control Operation
- Projection Modes
- Image Aspect Ratio
- Color Mode
- Adjusting the Brightness
- Adjusting Luminance Controls
- Adjusting Gamma
- Setting the Date and Time
- Adjusting Projector Features
- Shutting Off the Picture Temporarily
- Stopping Video Action Temporarily
- Projector Security Features
- Projecting Two Images Simultaneously
- Using Advanced Image Adjustment Features
- Using Multiple Projectors
- Enabling Protocol Emulation
- Saving Settings to Memory and Using Saved Settings
- Saving a Scheduled Event
- Copying Menu Settings Between Projectors
- Adjusting the Menu Settings
- Using the Projector's Menus
- Image Quality Settings - Image Menu
- Input Signal Settings - Signal Menu
- Projector Feature Settings - Settings Menu
- Projector Setup Settings - Extended Menu
- Projector Network and Camera Settings - Network Menu
- Projector Information Display - Info Menu
- Projector Reset Options - Reset Menu
- Maintaining and Transporting the Projector
- Solving Problems
- Projection Problem Tips
- Projector Light Status
- Viewing Projector Status Information
- Using the Projector Help Displays
- Solving Image Problems
- Solutions When No Image Appears
- Solutions When "No Signal" Message Appears
- Solutions When "Not Supported" Message Appears
- Solutions When Only a Partial Image Appears
- Solutions When the Image is Not Rectangular
- Solutions When the Image Contains Noise or Static
- Solutions When the Image is Fuzzy or Blurry
- Solutions When the Image Brightness or Colors are Incorrect
- Solutions When Automatic Adjustments are not Applied Correctly
- Solving Projector or Remote Control Operation Problems
- Solving Network Problems
- Where to Get Help
- Technical Specifications
- General Projector Specifications
- Projector Light Source Specifications
- Remote Control Specifications
- Projector Dimension Specifications
- Projector Electrical Specifications
- Projector Environmental Specifications
- Projector Safety and Approvals Specifications
- Safety and Approvals Specifications for Latin America
- Supported Video Display Formats
- Notices
Epson PRO-L20000UNL User Manual
Displayed below is the user manual for PRO-L20000UNL by Epson which is a product in the Data Projectors category. This manual has pages.
Related Manuals
Pro L20000UNL/L20002UNL
User's Guide
3
Contents
Pro L20000UNL/L20002UNL User's Guide .............................................................................................. 11
Introduction to Your Projector ................................................................................................................. 12
Projector Features.............................................................................................................................. 12
Additional Components ................................................................................................................ 13
Additional Projector Software and Manuals................................................................................... 14
Optional Equipment and Replacement Parts................................................................................. 15
Warranty and Registration Information .......................................................................................... 16
Notations Used in the Documentation ................................................................................................ 17
Where to Go for Additional Information .............................................................................................. 17
Projector Part Locations ..................................................................................................................... 17
Projector Parts - Front/Top ............................................................................................................ 18
Projector Parts - Side/Rear............................................................................................................ 19
Projector Parts - Base.................................................................................................................... 20
Projector Parts - Interface Ports .................................................................................................... 21
Projector Parts - Control Panel ...................................................................................................... 23
Projector Parts - Remote Control................................................................................................... 24
Setting Up the Projector ........................................................................................................................... 27
Projector Placement........................................................................................................................... 27
Projector Setup and Installation Options ....................................................................................... 29
Installing the Projector in a Mount.................................................................................................. 30
Protecting the Built-in Camera....................................................................................................... 32
Projection Distance........................................................................................................................ 32
Projector Connections........................................................................................................................ 33
Connecting to Video Sources ........................................................................................................ 34
Connecting to an HDMI Video Source ...................................................................................... 34
Connecting to a Component-to-BNC Video Source .................................................................. 35
Connecting to a Component Video Source ............................................................................... 35
Connecting to an SDI Video Source.......................................................................................... 36
Connecting to Computer Sources.................................................................................................. 37
Connecting to a Computer for VGA Video................................................................................. 37
4
Connecting to a Computer for HDMI Video............................................................................... 38
Connecting to a Computer for DVI-D Video .............................................................................. 38
Connecting to a Computer for 5 BNC Video.............................................................................. 39
Connecting to a Computer for DisplayPort Video...................................................................... 39
Connecting to an HDBaseT Transmitter ....................................................................................... 40
Connecting to an External Computer Monitor................................................................................ 41
Attaching and Removing a Lens......................................................................................................... 42
Attaching a Lens ........................................................................................................................... 42
Removing a Lens .......................................................................................................................... 47
Installing Batteries in the Remote Control .......................................................................................... 48
Using the Projector on a Network ............................................................................................................ 51
Wired Network Projection................................................................................................................... 51
Connecting to a Wired Network ..................................................................................................... 51
Selecting Wired Network Settings ................................................................................................. 52
Wireless Network Projection .............................................................................................................. 55
Using a QR Code to Connect a Mobile Device .............................................................................. 55
Using Quick Wireless Connection (Windows)................................................................................ 57
Selecting Wireless Network Settings Manually.............................................................................. 58
Wireless LAN Menu Settings .................................................................................................... 61
Selecting Wireless Network Settings in Windows.......................................................................... 63
Selecting Wireless Network Settings on Mac ................................................................................ 64
Setting Up Wireless Network Security ........................................................................................... 64
Setting Up Projector Network E-Mail Alerts ........................................................................................ 66
Network Projector E-mail Alert Messages ..................................................................................... 68
Selecting Other Network Settings....................................................................................................... 68
Setting a Static IP Address on the LCD Screen.................................................................................. 70
Controlling a Networked Projector Using a Web Browser .................................................................. 71
Web Control Options ..................................................................................................................... 73
Viewing an Image Capture of the Displayed Image from a Remote Location ............................... 79
Using Crestron Connected................................................................................................................. 83
Setting Up Crestron Connected..................................................................................................... 84
Controlling a Networked Projector Using Crestron Connected...................................................... 85
Art-Net Channel Definitions................................................................................................................ 87
5
Registering a Digital Certificate on the Projector ................................................................................ 92
Importing a Web Server Certificate Using the Projector Menus..................................................... 92
Registering Digital Certificates from a Web Browser ..................................................................... 94
Digital Certificate Types................................................................................................................. 95
Using Basic Projector Features ............................................................................................................... 97
Turning On the Projector .................................................................................................................... 97
Turning Off the Projector .................................................................................................................... 99
Selecting the Language for the Projector Menus.............................................................................. 101
Adjusting the Image Height .............................................................................................................. 102
Resizing the Image with the Zoom Button ........................................................................................ 103
Focusing the Image Using the Focus and Distortion Buttons ........................................................... 103
Setting the Screen Type................................................................................................................... 105
Adjusting the Image Position Using Lens Shift ................................................................................. 106
Adjusting the Image Position Using Screen Position........................................................................ 109
Displaying a Test Pattern ................................................................................................................. 109
Image Shape.................................................................................................................................... 110
Correcting Image Shape with H/V Keystone................................................................................ 110
Correcting Image Shape with Quick Corner ................................................................................ 112
Correcting Image Shape with Curved Surface ............................................................................ 114
Correcting Image Shape with Corner Wall................................................................................... 119
Correcting Image Shape with Point Correction............................................................................ 122
Selecting an Image Source .............................................................................................................. 124
Remote Control Operation ............................................................................................................... 126
Projection Modes ............................................................................................................................. 127
Changing the Projection Mode Using the Remote Control .......................................................... 127
Changing the Projection Mode Using the Menus......................................................................... 128
Image Aspect Ratio .......................................................................................................................... 129
Changing the Image Aspect Ratio ............................................................................................... 129
Available Image Aspect Ratios.................................................................................................... 130
Color Mode....................................................................................................................................... 131
Changing the Color Mode............................................................................................................ 131
Available Color Modes................................................................................................................. 132
Adjusting the Brightness................................................................................................................... 132
6
Constant Brightness Usage Hours .............................................................................................. 134
Adjusting Luminance Controls.......................................................................................................... 136
Adjusting Gamma............................................................................................................................. 138
Setting the Date and Time................................................................................................................ 140
Date and Time Settings ............................................................................................................... 141
Adjusting Projector Features ................................................................................................................. 142
Shutting Off the Picture Temporarily ................................................................................................ 142
Stopping Video Action Temporarily .................................................................................................. 143
Projector Security Features.............................................................................................................. 144
Password Security Types ............................................................................................................ 144
Setting a Password ................................................................................................................. 145
Selecting Password Security Types........................................................................................ 146
Entering a Password to Use the Projector............................................................................... 147
Saving a User's Logo Image to Display................................................................................... 148
Locking the Projector's Lens Settings and Buttons...................................................................... 150
Unlocking the Projector's Buttons ........................................................................................... 152
Locking the Remote Control Buttons .......................................................................................... 152
Installing a Security Cable ........................................................................................................... 154
Projecting Two Images Simultaneously............................................................................................ 154
Input Sources for Split Screen Projection .................................................................................... 156
Using Advanced Image Adjustment Features .................................................................................. 156
Using Frame Interpolation .......................................................................................................... 157
Creating Image Presets............................................................................................................... 159
Using MPEG Noise Reduction..................................................................................................... 160
Adjusting Scaled Resolution Images (Super-resolution) ............................................................. 161
Adjusting Detail Enhancement .................................................................................................... 162
Adjusting the Color Convergence (Panel Alignment)................................................................... 163
Adjusting the Color Tone (Color Uniformity) ................................................................................ 165
Running Light Source Calibration ................................................................................................ 167
Using Multiple Projectors ................................................................................................................. 169
Multiple Projector Adjustment Overview ...................................................................................... 169
Projector Identification System for Multiple Projector Control ...................................................... 171
Setting the Projector ID........................................................................................................... 171
7
Setting the Remote Control ID ................................................................................................ 172
Tiling Images into One Image...................................................................................................... 173
Configuring Tiling Automatically.............................................................................................. 173
Configuring Tiling Manually..................................................................................................... 176
Blending the Image Edges .......................................................................................................... 178
Adjusting the Black Level ............................................................................................................ 180
Matching Tint and Brightness (Screen Matching) ....................................................................... 184
Matching the Screens Automatically....................................................................................... 185
Matching the Screens Manually ............................................................................................. 186
Scaling an Image......................................................................................................................... 188
Enabling Protocol Emulation ............................................................................................................ 189
Saving Settings to Memory and Using Saved Settings .................................................................... 190
Saving a Scheduled Event ............................................................................................................... 192
Viewing Scheduled Events .......................................................................................................... 194
Editing a Scheduled Event........................................................................................................... 195
Copying Menu Settings Between Projectors .................................................................................... 196
Saving Settings to a USB Flash Drive.......................................................................................... 197
Transferring Settings from a USB Flash Drive ............................................................................. 198
Saving Settings to a Computer .................................................................................................... 200
Transferring Settings from a Computer ....................................................................................... 201
Adjusting the Menu Settings .................................................................................................................. 204
Using the Projector's Menus............................................................................................................. 204
Image Quality Settings - Image Menu .............................................................................................. 206
Input Signal Settings - Signal Menu.................................................................................................. 210
Projector Feature Settings - Settings Menu...................................................................................... 214
Projector Setup Settings - Extended Menu....................................................................................... 218
Projector Network and Camera Settings - Network Menu ................................................................ 225
Projector Information Display - Info Menu ........................................................................................ 227
Event ID Code List....................................................................................................................... 230
Projector Reset Options - Reset Menu............................................................................................. 231
Maintaining and Transporting the Projector ......................................................................................... 233
Projector Maintenance ..................................................................................................................... 233
Cleaning the Lens........................................................................................................................ 233
8
Cleaning the Projector Case........................................................................................................ 234
Air Filter and Vent Maintenance .................................................................................................. 234
Cleaning the Air Filters and Air Intake Vents........................................................................... 235
Replacing the Air Filters.......................................................................................................... 239
Replacing the Remote Control Batteries ..................................................................................... 242
Transporting the Projector................................................................................................................ 244
Solving Problems .................................................................................................................................... 247
Projection Problem Tips ................................................................................................................... 247
Projector Light Status ....................................................................................................................... 248
Viewing Projector Status Information ............................................................................................... 253
Projector Status Display Messages ............................................................................................. 255
Using the Projector Help Displays .................................................................................................... 260
Solving Image Problems .................................................................................................................. 261
Solutions When No Image Appears............................................................................................. 261
Solutions When "No Signal" Message Appears........................................................................... 262
Displaying From a PC Laptop ................................................................................................. 263
Displaying From a Mac Laptop ............................................................................................... 264
Solutions When "Not Supported" Message Appears ................................................................... 264
Solutions When Only a Partial Image Appears............................................................................ 264
Solutions When the Image is Not Rectangular ............................................................................ 265
Solutions When the Image Contains Noise or Static ................................................................... 266
Solutions When the Image is Fuzzy or Blurry .............................................................................. 266
Solutions When the Image Brightness or Colors are Incorrect .................................................... 267
Solutions When Automatic Adjustments are not Applied Correctly.............................................. 268
Solving Projector or Remote Control Operation Problems ............................................................... 269
Solutions to Projector Power or Shut-Off Problems..................................................................... 269
Solutions to Remote Control Problems........................................................................................ 270
Solutions to Password Problems ................................................................................................. 271
Solving Network Problems ............................................................................................................... 272
Solutions When Wireless Authentication Fails ............................................................................ 272
Solutions When You Cannot Access the Projector Through the Web ......................................... 273
Solutions When the Image Contains Static During Network Projection ....................................... 274
Solutions When Network Alert E-Mails are Not Received............................................................ 274
9
Where to Get Help............................................................................................................................ 274
Technical Specifications ........................................................................................................................ 276
General Projector Specifications ...................................................................................................... 276
Projector Light Source Specifications............................................................................................... 277
Remote Control Specifications ......................................................................................................... 278
Projector Dimension Specifications.................................................................................................. 278
Projector Electrical Specifications .................................................................................................... 278
Projector Environmental Specifications............................................................................................ 279
Projector Safety and Approvals Specifications................................................................................. 280
Safety and Approvals Specifications for Latin America .................................................................... 280
Supported Video Display Formats.................................................................................................... 281
Notices ..................................................................................................................................................... 285
Recycling.......................................................................................................................................... 285
Important Safety Information ............................................................................................................ 285
Important Safety Instructions............................................................................................................ 285
Laser Safety Information ............................................................................................................. 289
Laser Safety Labels..................................................................................................................... 289
Hazard Distance (HD) ................................................................................................................. 293
Typical Setup Configurations (U.S. Only) .................................................................................... 296
List of Safety Symbols (corresponding to IEC60950-1 A2)............................................................... 298
Manufacturer and Importer Address................................................................................................. 302
FCC Compliance Statement............................................................................................................. 303
Binding Arbitration and Class Waiver ............................................................................................... 303
Trademarks...................................................................................................................................... 306
Copyright Notice............................................................................................................................... 307
A Note Concerning Responsible Use of Copyrighted Materials................................................... 308
Copyright Attribution.................................................................................................................... 308
11
Pro L20000UNL/L20002UNL User's Guide
Welcome to the Pro L20000UNL/L20002UNL User's Guide.
For a printable PDF copy of this guide, click here.
12
Introduction to Your Projector
Refer to these sections to learn more about your projector and this manual.
Projector Features
Notations Used in the Documentation
Where to Go for Additional Information
Projector Part Locations
Projector Features
The Pro L20000UNL and Pro L20002UNL projectors include these special features:
Bright, high-resolution projection system
• Up to 20000 lumens of brightness (white light output and color light output)
Note: Color brightness (color light output) and white brightness (white light output) will vary depending
on usage conditions. Color light output measured in accordance with IDMS 15.4; white light output
measured in accordance with ISO 21118.
• Native resolution of 1920 × 1200 pixels (WUXGA)
Flexible connectivity
• Wired and wireless network support for projection, monitoring, and control via remote network
computer
• Variety of connection methods for a computer or video device including HDMI, BNC, DVI-D, SDI, and
HDBaseT
• Ports for connecting an external monitor
Easy-to-use setup and operation features
• Interchangeable bayonet lens options available
• Project images side by side from two separate input sources
• Create one large seamless display when projecting from multiple projectors using Edge Blending
• Epson's Instant Off and Direct Power On features for quick setup and shut down
• Support for Crestron Connected and Art-Net network monitoring systems
13
• Network message broadcast system to project timely messages to all networked projectors (Windows
only)
Additional Components
Additional Projector Software and Manuals
Optional Equipment and Replacement Parts
Warranty and Registration Information
Parent topic: Introduction to Your Projector
Related concepts
Projector Part Locations
Projector Connections
Using Multiple Projectors
Using Crestron Connected
Related topics
Using the Projector on a Network
Additional Components
Depending on how you plan to use the projector, you may need to obtain additional components.
Note: To connect a Mac that does not include a compatible video output port, you need to obtain an
adapter that allows you to connect to an input port on the projector. Contact Apple for compatible
adapter options. To connect a smartphone or tablet, you may need to obtain an adapter that allows you
to connect to the projector. This allows you to mirror your smartphone or tablet screens, watch movies,
and more. Contact your device manufacturer for compatible adapter options.
Unless listed as available from Epson in this table, see your local computer or electronics dealer for
purchase information.
Signal or connection
type
Additional component necessary
Component video Component-to-BNC or D-sub, 15-pin, component-to-VGA video cable or
adapter
Available for purchase from Epson or an authorized Epson reseller.
14
Signal or connection
type
Additional component necessary
HDMI HDMI cable
Available for purchase from Epson or an authorized Epson reseller.
You also need a splitter that supports HDMI signals (commerically
available).
VGA VGA computer cable
Available for purchase from Epson or an authorized Epson reseller.
If you want to connect the projector using a splitter, you also need a splitter
that supports VGA signals (commercially available) and a second VGA
computer cable.
BNC VGA-to-5-BNC cable or adapter
Available for purchase from Epson or an authorized Epson reseller.
DVI-D Compatible DVI-D cable
HDBaseT Compatible 100Base-TX LAN cable
SDI Compatible BNC video cable
DisplayPort Compatible DisplayPort cable (with optional DisplayPort interface board
installed)
Parent topic: Projector Features
Related concepts
Projector Connections
Related references
Optional Equipment and Replacement Parts
Additional Projector Software and Manuals
After connecting and setting up the projector, install the projector software as necessary. You may need
to install it from a software CD, if included, or download the software and manuals as necessary.
You can install the projector software programs listed here and view their manuals for instructions on
using them.
15
Note: If you still need help after checking this manual and the sources listed here, you can use the
Epson PrivateLine Support service to get help fast. For details, see "Where to Get Help."
Projector software Manual Description
Epson Projector
Management (Windows
only)
Epson Projector
Management Operation
Guide
Lets you monitor and control your projector
through the network.
You can download the latest software and
documentation from the Epson web site. Go to
epson.com/support (U.S.) or epson.ca/support
(Canada) and select your projector.
Epson iProjection
(Windows/Mac)
Epson iProjection
Operation Guide
(Windows/Mac)
Lets you project the computer screens of
users over a network.
You can download the latest software and
documentation from the Epson web site. Go to
epson.com/support (U.S.) or epson.ca/support
(Canada) and select your projector.
Epson Projector
Professional Tool
(Windows only)
Epson Projector
Professional Tool
Operation Guide
Lets you manage multiple Epson projectors
simultaneously
You can download the latest software and
documentation from the Epson web site. Go to
epson.com/support (U.S.) or epson.ca/support
(Canada) and select your projector.
—Open Source Software
License
You can download this document from the
Epson web site. Go to epson.com/support
(U.S.) or epson.ca/support (Canada) and
select your projector.
Parent topic: Projector Features
Optional Equipment and Replacement Parts
You can purchase screens, other optional accessories, and replacement parts from an Epson authorized
reseller. To find the nearest reseller, call 800-GO-EPSON (800-463-7766) in the U.S. or 800-807-7766 in
Canada. Or you can purchase online at epsonstore.com (U.S. sales) or epsonstore.ca (Canadian sales).
Epson offers the following optional accessories and replacement parts for your projector:
16
Option or part Part number
Air filter (ELPAF58) V13H134A58
HDBaseT Transmitter (ELPHD01) V12H547020
HDMI/DVI-D interface board (ELPIF01) V12H917F01
DisplayPort interface board (ELPIF03) V12H916F01
Remote control cable set (ELPKC28) V12H005C28
Ultra short-throw lens (ELPLX02) V12H004X02
White ultra short-throw lens (ELPLX02W) V12H004Y02
Short-throw zoom lens (ELPLU04) V12H004U04
Wide-throw zoom lens (ELPLW06) V12H004W06
Wide-throw zoom lens (ELPLW08) V12H004W08
Middle-throw zoom lens (ELPLM15) V12H004M0F
Middle-throw zoom lens (ELPLM10) V12H004M0A
Middle-throw zoom lens (ELPLM11) V12H004M0B
Long throw zoom lens (ELPLL08) V12H004L08
Epson Stacking and Rigging Frame (ELPMB57) V12H989A01
Parent topic: Projector Features
Warranty and Registration Information
Your projector comes with a basic warranty that lets you project with confidence. For details, see the
warranty that came with your projector.
In addition, Epson offers free Extra Care Road Service. In the unlikely event of an equipment failure, you
won’t have to wait for your unit to be repaired. Instead, Epson will ship you a replacement unit anywhere
in the United States, Canada, or Puerto Rico. See the Extra Care Road Service brochure for details.
Note: Availability varies by region.
Register your product online at this site: epson.com/webreg.
Registering also lets you receive special updates on new accessories, products, and services.
Parent topic: Projector Features
17
Notations Used in the Documentation
Follow the guidelines in these notations as you read your documentation:
•Warnings must be followed carefully to avoid bodily injury.
•Cautions must be observed to avoid damage to your equipment.
•Notes contain important information about your projector.
•Tips contain additional projection information.
Parent topic: Introduction to Your Projector
Where to Go for Additional Information
Need quick help on using your projector? Here's where to look for help:
•epson.com/support (U.S.), epson.ca/support (Canada), or epson.com.jm/support (Caribbean)
View FAQs (frequently asked questions) and e-mail your questions to Epson technical support 24
hours a day.
• If you still need help after checking this manual and any other sources listed here, you can use the
Epson PrivateLine Support service to get help fast. For details, see "Where to Get Help."
Parent topic: Introduction to Your Projector
Related references
Where to Get Help
Related topics
Solving Problems
Projector Part Locations
Check the projector part illustrations to learn about the parts on your projector.
Projector Parts - Front/Top
Projector Parts - Side/Rear
Projector Parts - Base
Projector Parts - Interface Ports
Projector Parts - Control Panel
Projector Parts - Remote Control
Parent topic: Introduction to Your Projector
18
Projector Parts - Front/Top
1 Cap for lens cover
2 Built-in camera
3 Projection lens
4 Lens cover
5 Air filter covers
6 Remote receivers
7 Status lights
8 Replacement lens cover (for certain lenses)
9 Holes for optional mounting
Parent topic: Projector Part Locations
Related topics
Attaching and Removing a Lens
21
Related tasks
Installing a Security Cable
Transporting the Projector
Projector Parts - Interface Ports
1Slot 1 for installing an interface board (HDMI/DVI-D interface board described below)
2Slot 2 for installing an optional DisplayPort interface board (described below)
3HDBaseT port
4 Network LAN port
5Computer In port
6Computer/BNC Out port
7BNC In ports
8 Cable clip slot
9RS-232C port
10 Remote port
11 SDI Out port
12 SDI In port
22
13 Service port
14 USB-A port
HDMI/DVI-D Interface Board
1DVI-D In port
2HDMI In port
3DC Out port
Optional DisplayPort Interface Board
1DisplayPort In1 port
2DisplayPort In2 port
Caution: Do not attempt to install or remove your projector's interface board. Static electricity or other
interference may damage the projector or cause it to malfunction. Contact Epson to have an interface
board installed or removed.
Parent topic: Projector Part Locations
Related references
Optional Equipment and Replacement Parts
23
Projector Parts - Control Panel
1On button (turns on the projector)
2Standby button (turns off the projector)
3Sync. lights (indicate the selected image source)
4Sync. buttons (select an image source)
5Auto button (automatically adjusts computer images)
6Test Pattern button (displays a test pattern)
7Lens Shift button (adjusts the image position)
8Calibration button (starts lens calibration)
9Zoom button (changes the image size)
10 Focus button (adjusts the image focus)
11 Distortion button (corrects image distortion)
12 Geometry button (adjusts the image shape)
24
13 Shutter button (turns input signal on or off temporarily)
14 Enter button (selects options)
15 Arrow buttons (move through on-screen options; adjust the focus, zoom, and lens shift)
16 Lock button (displays the Control Panel Lock screen)
17 Light button (lights up the control panel buttons and LCD screen temporarily)
18 Esc button (cancels/exits functions)
19 Arrow buttons (select LCD screen settings)
20 LCD screen (displays projector status information)
21 Menu button (accesses projector menu system)
Parent topic: Projector Part Locations
Projector Parts - Remote Control
25
1On button (turns on the projector)
2Standby button (turns off the projector)
3 Source buttons (select an image source)
4User1,User2, and User3 buttons (open menu assigned by user)
5Aspect button (selects the image aspect ratio)
6Auto button (automatically adjusts computer images)
7Freeze button (stops video action)
8Default button (resets settings to their default values in the projector menu system)
9Menu button (accesses projector menu system)
10 Arrow buttons (move through on-screen options and move pointer)
11 Enter button (selects options)
12 On-Screen button (displays or hides the on-screen menus or messages)
13 Zoom button (changes the image size)
14 Focus button (adjusts the image focus)
15 Lens Shift button (adjusts the image position)
16 Page up and down buttons (scroll through image files when projecting from a computer over a
network connection, or change the displayed test pattern)
17 Numeric buttons (enter numbers)
18 ID button (hold down and use numeric keys to select projector to control)
19 ID switch (selects control of one or all projectors from the remote control)
20 Remote port (connects to a remote control cable)
21 ibutton (displays the Info menu)
22 Num button (hold down and use numeric keys to enter numbers)
23 Test Pattern button (displays a test pattern)
24 Geometry button (corrects image shape)
25 Calibration button (starts lens calibration)
26 Distortion button (corrects image distortion)
27 Shutter button (turns signal on or off temporarily)
26
28 Esc button (cancels/exits functions and moves to previous menu levels)
29 Memory button (saves and applies presets)
30 Color Mode button (selects display modes)
31 Search button (searches for connected sources)
32 Light button (lights up the remote control buttons temporarily)
33 Indicator light (lights up when the remote control is in use)
34 Remote control signal emitter (emits remote control signals)
Parent topic: Projector Part Locations
27
Setting Up the Projector
Follow the instructions in these sections to set up your projector for use.
Projector Placement
Projector Connections
Attaching and Removing a Lens
Installing Batteries in the Remote Control
Projector Placement
You can place the projector on almost any flat surface to project an image.
You can also install the projector in a ceiling mount if you want to use it in a fixed location.
Keep these considerations in mind as you select a projector location:
• Place the projector on a sturdy, level surface or install it using a compatible mount.
• Install the projector at any angle. There is no vertical or horizontal limit to how the projector can be
installed.
• Leave plenty of space around and under the projector for ventilation as described here, and do not
place it on top of or next to anything that could block the vents.
• Place the projector parallel to the screen.
• Position the projector within reach of a grounded electrical outlet or extension cord.
28
Caution: Be sure to leave the following amount of space around the projector to avoid blocking the air
exhaust and intake vents.
1 7.87 inches (20 cm)
2 19.7 inches (50 cm)
Caution: If you are setting up the projector with the intake vent facing down or placing the projector in a
mount, be sure to leave the following amount of space around the projector.
1 3.9 inches (10 cm)
2 7.87 inches (20 cm)
Note: When setting up multiple projectors, leave the following amount of space between the projectors.
1 19.7 inches (50 cm)
29
If you are stacking multiple projectors, follow these guidelines:
• Do not stack more than two projectors.
• Tilt the projectors only within the extendable range of the feet.
• Make sure all of the projector's feet sit firmly on the projector below.
Projector Setup and Installation Options
Installing the Projector in a Mount
Protecting the Built-in Camera
Projection Distance
Parent topic: Setting Up the Projector
Projector Setup and Installation Options
You can set up or install your projector in the following ways:
Front
Rear
30
Front ceiling
Rear ceiling
If you project from the ceiling or from the rear, select the correct Projection setting and, if necessary,
adjust the OSD Rotation setting.
Parent topic: Projector Placement
Related references
Projector Setup Settings - Extended Menu
Installing the Projector in a Mount
When installing the projector in an optional mount, follow these guidelines:
31
• When using a ceiling or portrait mount, use commercially available M6 screws (up to a depth of 1.06
inches [27 mm]) to attach the mount to the projector at these four points:
• When using a clamp to attach the projector to an aluminum truss, use commercially available M6
screws (up to a depth of 1.06 inches [27 mm]) to attach the clamp to at least four points on the
projector. You can use any of these points on the projector to accommodate the distance between the
screw holes and the center of the aluminum truss pipe.
Caution: Make sure to attach a commercially available drop-prevention wire that supports weights of at
least 220 lb (100 kg) to secure the projector to the mount to prevent it from falling. Make sure there is no
slack in the wire and that it is securely attached to the two connection points on the bottom of the
projector.
32
Parent topic: Projector Placement
Related references
Projector Parts - Side/Rear
Protecting the Built-in Camera
If you use the projector near other devices that emit laser beams, install the protective plate over the
built-in camera to protect it from interference.
Remove the protective plate from its storage area on the side of the projector and place it over the built-
in camera on the front of the projector. When you finish, remove the protective plate from the camera
and return it to its storage area.
Parent topic: Projector Placement
Related references
Projector Parts - Front/Top
Projection Distance
The distance at which you place the projector from the screen determines the approximate size of the
image. The image size increases the farther the projector is from the screen, but can vary depending on
the zoom factor, aspect ratio, and other settings.
Use the tables here to determine approximately how far to place the projector from the screen based on
the installed lens and the size of the projected image. (Conversion figures may have been rounded up or
down.)
33
You can also use the projector Throw Distance Calculator at epson.com/support (U.S.) or
epson.ca/support (Canada).
Number Lens Screen size Projection distance
1 ELPLX02
ELPLX02W
100 to 1000 inches
(254 to 2540 cm)
29.1 to 302.8 inches (74 to 769 cm)
2 ELPLU04 60 to 1000 inches
(152.4 to 2540 cm)
31.5 to 670.0 inches (80 to 1702 cm)
3 ELPLW08 42.9 to 1039.0 inches (109 to 2639 cm)
4 ELPLW06 58.7 to 1395.3 inches (149 to 3544 cm)
5 ELPLM15 78.3 to 2190.2 inches (199 to 5563 cm)
6 ELPLM10 120.5 to 3183.5 inches (306 to 8086 cm)
7 ELPLM11 175.2 to 4648.4 inches (445 to 11807 cm)
8 ELPLL08 261.4 to 6367.7 inches (664 to 16174 cm)
Note: If the screen is larger than 500 inches (1270 cm), fine text and images may not display clearly.
Parent topic: Projector Placement
Related references
Optional Equipment and Replacement Parts
Projector Connections
See these sections to connect the projector to a variety of projection sources.
Caution: If you will use the projector at altitudes above 4921 feet (1500 m), turn on High Altitude Mode
to ensure the projector's internal temperature is regulated properly.
34
Connecting to Video Sources
Connecting to Computer Sources
Connecting to an HDBaseT Transmitter
Connecting to an External Computer Monitor
Parent topic: Setting Up the Projector
Related references
Projector Setup Settings - Extended Menu
Connecting to Video Sources
Follow the instructions in these sections to connect video devices to the projector.
Connecting to an HDMI Video Source
Connecting to a Component-to-BNC Video Source
Connecting to a Component Video Source
Connecting to an SDI Video Source
Parent topic: Projector Connections
Connecting to an HDMI Video Source
If your video source has an HDMI port, you can connect it to the projector using an optional HDMI cable.
The HDMI connection provides the best image quality.
1. Connect the HDMI cable to your video source's HDMI output port.
2. Connect the other end to the projector's HDMI In port on the HDMI/DVI-D board in slot 1. If you are
connecting an optical HDMI cable, you must also connect the cable's USB power connector to the
DC Out port on the board.
35
Note: Depending on the length and performance quality of the HDMI cable, images may not display
correctly. For best results, use a cable that conforms to the HDMI standard.
Parent topic: Connecting to Video Sources
Connecting to a Component-to-BNC Video Source
If your video source has component video ports, you can connect it to the projector using an optional
component-to-BNC video cable. Depending on your component ports, you may need to use an adapter
cable along with a component video cable.
1. Connect the component connectors to your video source's color-coded component video output
ports, usually labeled Y,Pb,Pr or Y,Cb,Cr. If you are using an adapter, connect these connectors
to your component video cable.
2. Connect the BNC connectors to the projector's R/Cr/Pr,G/Y,B/Cb/Pb ports.
Parent topic: Connecting to Video Sources
Connecting to a Component Video Source
If your video source has component video ports, you can connect it to the projector using an optional
component-to-VGA video cable. Depending on your component ports, you may need to use an adapter
cable along with a component video cable.
1. Connect the component connectors to your video source's color-coded component video output
ports, usually labeled Y,Pb,Pr or Y,Cb,Cr. If you are using an adapter, connect these connectors
to your component video cable.
36
2. Connect the VGA connector to the Computer In port on the projector.
3. Tighten the screws on the VGA connector.
If your image colors appear incorrect, you may need to change the Input Signal setting in the projector's
Signal menu.
Parent topic: Connecting to Video Sources
Related references
Input Signal Settings - Signal Menu
Connecting to an SDI Video Source
If your video source has an SDI port, you can connect it to the projector using an optional BNC video
cable.
1. Connect the BNC video cable to your video source's SDI output port.
2. Connect the other end to the projector's SDI In port.
Note: Select the signal for the SDI In port in the SDI Settings in the Extended menu.
Parent topic: Connecting to Video Sources
37
Related references
Projector Setup Settings - Extended Menu
Connecting to Computer Sources
Follow the instructions in these sections to connect a computer to the projector.
Connecting to a Computer for VGA Video
Connecting to a Computer for HDMI Video
Connecting to a Computer for DVI-D Video
Connecting to a Computer for 5 BNC Video
Connecting to a Computer for DisplayPort Video
Parent topic: Projector Connections
Connecting to a Computer for VGA Video
You can connect the projector to your computer using a VGA computer cable.
Note: To connect a Mac that does not include a compatible video output port, you need to obtain an
adapter that allows you to connect to an input port on the projector. Contact Apple for compatible
adapter options. To connect a smartphone or tablet, you may need to obtain an adapter that allows you
to connect to the projector. This allows you to mirror your smartphone or tablet screens, watch movies,
and more. Contact your device manufacturer for compatible adapter options.
1. If necessary, disconnect your computer's monitor cable.
2. Connect the VGA computer cable to your computer's monitor port.
3. Connect the other end to the Computer In port on the projector.
4. Tighten the screws on the VGA connector.
38
Parent topic: Connecting to Computer Sources
Connecting to a Computer for HDMI Video
If your computer has an HDMI port, you can connect it to the projector using an optional HDMI cable.
Note: To connect a Mac that does not include a compatible video output port, you need to obtain an
adapter that allows you to connect to an input port on the projector. Contact Apple for compatible
adapter options. To connect a smartphone or tablet, you may need to obtain an adapter that allows you
to connect to the projector. This allows you to mirror your smartphone or tablet screens, watch movies,
and more. Contact your device manufacturer for compatible adapter options.
1. Connect the HDMI cable to your computer's HDMI output port.
2. Connect the other end to the projector's HDMI In port on the HDMI/DVI-D board in slot 1. If you are
connecting an optical HDMI cable, you must also connect the cable's USB power connector to the
DC Out port on the board.
Note: Depending on the length and performance quality of the HDMI cable, images may not display
correctly. For best results, use a cable that conforms to the HDMI standard.
Parent topic: Connecting to Computer Sources
Connecting to a Computer for DVI-D Video
If your computer has a DVI-D connector, you can connect it to the projector using an optional DVI-D
cable.
1. Connect the DVI-D cable to your computer's DVI-D connector.
39
2. Connect the other end to the projector's DVI-D In port on the HDMI/DVI-D interface board in slot 1.
Parent topic: Connecting to Computer Sources
Connecting to a Computer for 5 BNC Video
You can connect the projector to your computer using an optional VGA-to-5-BNC cable.
1. Connect the VGA connector to your computer's monitor port.
2. Connect the 5 BNC connectors to the projector's BNC In ports.
Parent topic: Connecting to Computer Sources
Connecting to a Computer for DisplayPort Video
If your computer has a DisplayPort connector, you can connect it to the projector using an optional
DisplayPort cable. You must have installed the optional DisplayPort interface board in slot 2 to provide a
DisplayPort connection.
1. Connect the DisplayPort cable to your computer's DisplayPort connector.
40
2. Connect the other end to the projector's DisplayPort In port on the optional DisplayPort interface
board in slot 2.
Parent topic: Connecting to Computer Sources
Related references
Optional Equipment and Replacement Parts
Connecting to an HDBaseT Transmitter
To send an HDMI or RS-232C signal over a long distance, you can connect the projector to an optional
HDBaseT transmitter using a 100Base-TX network cable. This is useful when you want to send a signal
to or control the projector from a remote location, such as in a hall or event site, since you can use a
network cable up to 328 feet (100 m) in length. To ensure proper data transmission, use a Category 6
STP cable or better.
1. Turn off the projector and HDBaseT transmitter.
Note: Make sure the projector and HDBaseT transmitter are turned off when connecting or
disconnecting a network cable between the two devices.
2. Connect one end of the network cable to the HDBaseT port on the transmitter.
3. Connect the other end to the projector's HDBaseT port.
41
Note: See the documentation that came with the HDBaseT transmitter for instructions on connecting
it to your video device or computer.
4. Turn on the projector and HDBaseT transmitter.
Note: To enable communication from the Ethernet and serial ports on the transmitter, select On as the
Control Communications setting in the projector's Extended menu. Turning on this setting disables the
projector's LAN,RS-232C, and Remote ports. If you connected an Extron XTP transmitter or switcher to
the projector's HDBaseT port, select On as the Extron XTP setting in the projector's Extended menu.
Parent topic: Projector Connections
Related references
Projector Setup Settings - Extended Menu
Connecting to an External Computer Monitor
If you connected a computer to the projector's Computer In or BNC In ports, or a video source to the
projector's SDI In port, you can also connect an external monitor to the projector. This lets you see your
presentation on the external monitor even when the projected image is not visible.
1. Make sure your computer or video source is connected to the projector's Computer In,BNC In, or
SDI In port.
42
2. Connect the external monitor's cable to your projector's Computer/BNC Out (for computer or BNC
sources) or SDI Out (for SDI sources) port.
Parent topic: Projector Connections
Attaching and Removing a Lens
Follow the instructions in these sections to attach or remove a compatible lens.
Attaching a Lens
Removing a Lens
Parent topic: Setting Up the Projector
Attaching a Lens
You can attach a compatible lens to the projector.
Warning: Turn off the projector and unplug its power cord before attaching or removing a lens;
otherwise you could receive an electric shock.
43
1. Turn off the projector and unplug the power cord.
Caution: Avoid touching the lens with your bare hands to prevent fingerprints on or damage to the
lens surface. Make sure the front of the projector is not facing up when you attach the lens. This
prevents dirt or dust from entering the projector and lowering the projection quality.
2. Use your hand to loosen the screw securing the lens cover to the projector.
3. Press the buttons on the sides of the lens cover and pull the lens cover off the projector.
4. If you are attaching the ELPLX02 or ELPLX02W lens, loosen the screws securing the lens
replacement cover on top of the projector and slide the cover off as shown.
44
5. If the lens lock lever is in the Lock position, release the lock lever. Pull the black lever up (1), pinch
the metal tab against the lever, move it toward the Release position until it stops (2), and then push
the black lever in as shown (3).
6. If the lens has a cap covering its narrower end, remove the cap and store it for use if you remove the
lens later.
45
7. Position the lens so the white circle is on top and insert the lens straight into the projector's lens
socket.
8. Hold the lens firmly as you lock the lens in place. Pull the black lever up (1), pinch the metal tab
against the lever, move it toward the Lock position until it stops (2), and then push the black lever in
as shown (3).
46
9. Replace the lens cover as shown.
10. Tighten the screw to secure the lens cover to the projector.
11. Do one of the following:
• If you attach a lens that is different from the previous lens, you see a message to calibrate the lens
the next time you turn on the projector. Select Yes to calibrate the lens.
• If you remove and attach the same lens, press and hold the Default button on the remote control
for at least 3 seconds or select Lens Calibration in the Extended menu to calibrate the lens.
Lens calibration takes up to 3 minutes to complete. When calibration is finished, the lens returns to
its previous position.
Caution: If you see a message that lens calibration failed, turn off the projector, unplug the power
cord, remove the lens, and reinstall it. If you continue to see an error message, contact Epson.
47
Parent topic: Attaching and Removing a Lens
Related references
Projector Setup Settings - Extended Menu
Removing a Lens
You can remove a lens to replace it with a different lens.
Warning: Turn off the projector and unplug its power cord before attaching or removing a lens;
otherwise you could receive an electric shock.
Caution: Remove the lens only when necessary and make sure the front of the projector is not facing up
when you remove the lens. This prevents dirt or dust from entering the projector and lowering the
projection quality. Avoid touching the lens with your bare hands to prevent fingerprints on or damage to
the lens surface.
1. Center the lens using the Lens Shift button.
2. Turn off the projector and unplug the power cord.
Warning: Wait about 30 minutes after turning off the projector before removing the lens. Touching
the lens immediately after projecting or turning off the projector may cause burns.
3. Use your hand to loosen the screw securing the lens cover to the projector.
48
4. Press the buttons on the sides of the lens cover and pull the lens cover off the projector.
5. Hold the lens firmly as you release the lens lock. Pull the black lever up (1), pinch the metal tab
against the lever, move it toward the Release position until it stops (2), and then push the black lever
in as shown (3).
6. Remove the lens from the projector.
7. If you are not attaching a different lens right away, replace the lens cover and lens cover cap to
protect the projector.
Parent topic: Attaching and Removing a Lens
Related tasks
Adjusting the Image Position Using Lens Shift
Installing Batteries in the Remote Control
The remote control uses the two AA batteries that came with the projector.
49
Caution: Use only the type of batteries specified in this manual. Do not install batteries of different types,
or mix new and old batteries.
1. Remove the battery cover.
2. Insert the batteries with the +and –ends facing as shown.
Warning: Make sure the batteries are inserted in the correct positions. If the batteries are not
inserted correctly, they could explode or leak, causing a fire, injury, or damage to the product.
50
3. Replace the battery cover and press it down until it clicks into place.
Warning: Dispose of used batteries according to local regulations. Do not expose batteries to heat
or flame. Keep batteries out of the reach of children; they are choking hazards and are very
dangerous if swallowed.
Parent topic: Setting Up the Projector
51
Using the Projector on a Network
Follow the instructions in these sections to set up your projector for use on a network.
Wired Network Projection
Wireless Network Projection
Setting Up Projector Network E-Mail Alerts
Selecting Other Network Settings
Setting a Static IP Address on the LCD Screen
Controlling a Networked Projector Using a Web Browser
Using Crestron Connected
Art-Net Channel Definitions
Registering a Digital Certificate on the Projector
Wired Network Projection
You can project through a wired network. To do this, you connect the projector to your network with an
Ethernet cable, and then set up your projector and computer for network projection.
After connecting and setting up the projector, install the projector software. You may need to install it
from a software CD, if included, or download the software and manuals as necessary.
Note: If your projector is connected via a LAN (Ethernet) cable to a network that includes a wireless
access point, you can connect to the projector wirelessly through the access point using the Epson
network software.
Connecting to a Wired Network
Selecting Wired Network Settings
Parent topic: Using the Projector on a Network
Related references
Additional Projector Software and Manuals
Connecting to a Wired Network
To connect the projector to a wired local area network (LAN), use a 100Base-TX or 10Base-T network
cable. You can also connect a commercially available etherCON LAN cable. To ensure proper data
transmission, use a Category 5 shielded cable or better.
52
1. Connect one end of the network cable to your network hub, switch, or router.
2. Connect the other end of the cable to the projector's LAN port.
Parent topic: Wired Network Projection
Selecting Wired Network Settings
Before you can project from computers on your network, you must select the network settings for the
projector using its menu system.
Note: Make sure you already connected the projector to your wired network using the LAN port.
1. Turn on the projector.
2. Press the Menu button.
3. Select the Network menu and press Enter.
53
4. Select Network Configuration and press Enter.
5. Select the Basic menu and press Enter.
6. Select the following basic options as necessary:
•Projector Name lets you enter a name up to 16 alphanumeric characters long to identify the
projector over the network.
•PJLink Password lets you enter a password up to 32 alphanumeric characters long for using the
PJLink protocol for projector control.
•Remote Password lets you enter a password up to 8 alphanumeric characters long for accessing
the Remote screen in Epson Web Control. (Default user name is EPSONREMOTE; default
password is guest.)
•Web Control Password lets you enter a password up to 8 alphanumeric characters long for
accessing Epson Web Control. (Default user name is EPSONWEB; default password is admin.)
•Moderator Password lets you enter a password up to 4 numbers long for accessing the projector
as a moderator with the Epson iProjection (Windows/Mac) software or the Epson iProjection app.
•Projector Keyword lets you turn on a security password to prevent access to the projector by
anyone not in the room with it. The projector displays a random keyword that you must enter from
a computer using the Epson iProjection (Windows/Mac) software or an iOS or Android device, or
on a Chromebook, using the Epson iProjection app.
•Display Keyword lets you display a keyword on the projected image when accessing the
projector from a computer using the Epson iProjection (Windows/Mac) software or an iOS or
Android device, or on a Chromebook, using the Epson iProjection app.
54
•Display LAN Info lets you select how the projector displays network information. You can select
an option to display a QR code that lets you quickly connect your iOS or Android devices using the
Epson iProjection app.
Note: Use the displayed keyboard to enter the name, passwords, and keyword. Press the arrow
buttons on the remote control to highlight characters and press Enter to select them.
7. Select the Wired LAN menu and press Enter.
8. Select your IP Settings as necessary:
• If your network assigns addresses automatically, turn on the DHCP setting.
• If you must set addresses manually, turn off DHCP and enter the projector's IP Address,Subnet
Mask, and Gateway Address as needed.
Note: To highlight the numbers you want from the displayed keyboard, press the arrow buttons on
the remote control. To select a highlighted number, press Enter.
9. To prevent display of the IP address on the standby screen, turn off IP Address Display.
10. To connect the projector to the network using IPv6, select On as the IPv6 Settings option. Then
select the Auto Configuration and Use Temporary Address settings as necessary.
11. When you finish selecting settings, select Complete and follow the on-screen instructions to save
your settings and exit the menus.
55
Parent topic: Wired Network Projection
Wireless Network Projection
You can project over a wireless network. To do this, you must set up your projector and computer for
wireless projection.
To connect wirelessly to your projector, configure the connection using the projector's Network menus.
After connecting and setting up the projector, install the projector software. You may need to install it
from a software CD, if included, or download the software and manuals as necessary.
Note: If your projector is connected via a LAN cable to a network that includes a wireless access point,
you can connect to the projector wirelessly through the access point using the Epson network software.
Using a QR Code to Connect a Mobile Device
Using Quick Wireless Connection (Windows)
Selecting Wireless Network Settings Manually
Selecting Wireless Network Settings in Windows
Selecting Wireless Network Settings on Mac
Setting Up Wireless Network Security
Parent topic: Using the Projector on a Network
Related references
Additional Projector Software and Manuals
Using a QR Code to Connect a Mobile Device
After you select the wireless network settings for your projector, you can display a QR code on the
screen and use it to connect a mobile device using the Epson iProjection app.
Note: Make sure you have installed the latest version of Epson iProjection on your device. Visit
epson.com/iprojection (U.S.) or epson.ca/iprojection (Canada) for more information.
1. Press the Menu button.
56
2. Select the Network menu and press Enter.
3. Select Network Configuration and press Enter.
4. Select the Basic menu and press Enter.
5. Set the Display LAN Info setting to Text & QR Code.
6. Select Complete and follow the on-screen instructions to save your settings and exit the menus.
57
7. Do one of the following:
• Press the LAN button on the remote control.
• Select Display the QR Code in the projector's Network menu.
Your projector displays the QR code on the projection surface.
Note: If you do not see the QR code after pressing the LAN button, press Enter to display it.
8. Start Epson iProjection on your mobile device.
9. Use the QR code reader feature to read the QR code and connect your device to the projector. Visit
epson.com/iprojection (U.S.) or epson.ca/iprojection (Canada) for instructions.
Parent topic: Wireless Network Projection
Related references
Additional Projector Software and Manuals
Using Quick Wireless Connection (Windows)
You can create a Quick Wireless Connection USB Key to quickly connect the projector to a Windows
computer wirelessly. Then you can project your presentation and remove the key when you are done.
Note: A USB flash drive is not included with your projector.
1. Create a Quick Wireless Connection USB Key with a USB flash drive and the Epson iProjection
(Windows) software.
Note: See the online Epson iProjection Operation Guide for instructions.
2. Turn on the projector.
3. Press the LAN button on the remote control.
The LAN standby screen is displayed.
4. Verify the SSID and IP address.
5. Insert the USB key into the projector's USB-A port.
You see a projected message that the network information update is complete.
6. Remove the USB key.
58
7. Insert the USB key into a USB port on your computer.
Note: In Windows Vista, if you see the AutoPlay window, select Run MPPLaunch.exe, then select
Allow on the next screen.
8. Follow the on-screen instructions to install the Epson iProjection software.
Note: If you see a Windows Firewall message, click Yes to disable the firewall. You need
administrator authority to install the software. If it is not installed automatically, double-click
MPPLaunch.exe in the USB key.
After a few minutes, your computer image is displayed by the projector. If it does not appear, press
the LAN or Source Search button on your remote control or restart your computer.
9. Run your presentation as necessary.
10. When you finish projecting wirelessly, select the Safely Remove Hardware option in the Windows
taskbar, then remove the USB key from your computer.
Note: You can share the USB key with other computers without disconnecting your computer. You
may need to restart your computer to reactivate your wireless LAN connection.
Parent topic: Wireless Network Projection
Related references
Additional Projector Software and Manuals
Projector Parts - Interface Ports
Selecting Wireless Network Settings Manually
Before you can project from your wireless network, you must select the network settings for the projector
using its menu system.
1. Turn on the projector.
2. Press the Menu button.
59
3. Select the Network menu and press Enter.
4. Make sure the Wireless Mode setting is set to Wireless LAN On.
5. Select Network Configuration and press Enter.
6. Select the Basic menu and press Enter.
7. Select the following basic options as necessary:
•Projector Name lets you enter a name up to 16 alphanumeric characters long to identify the
projector over the network.
60
•PJLink Password lets you enter a password up to 32 alphanumeric characters long for using the
PJLink protocol for projector control.
•Remote Password lets you enter a password up to 8 alphanumeric characters long for accessing
the Remote or Basic Control screen in the Epson Web Control. (Default user name is
EPSONREMOTE; default password is guest.)
•Web Control Password lets you enter a password up to 8 alphanumeric characters long for
accessing the projector over the web. (Default user name is EPSONWEB; default password is
admin.)
•Moderator Password lets you enter a password up to 4 numbers long for accessing the projector
as a moderator with the Epson iProjection (Windows/Mac) software or the Epson iProjection app.
•Projector Keyword lets you turn on a security password to prevent access to the projector by
anyone not in the room with it. The projector displays a random keyword that you must enter from
a computer using the Epson iProjection (Windows/Mac) software or an iOS or Android device, or
on a Chromebook, using the Epson iProjection app.
•Display Keyword lets you display a keyword on the projected image when accessing the
projector from a computer using the Epson iProjection (Windows/Mac) software or an iOS or
Android device, or on a Chromebook, using the Epson iProjection app.
•Display LAN Info lets you select how the projector displays network information. You can select
an option to display a QR code that lets you quickly connect your iOS or Android devices with the
Epson iProjection app.
Note: Use the displayed keyboard to enter the name, passwords and keyword. Press the arrow
buttons on the remote control to highlight characters and press Enter to select them.
61
8. Select the Wireless LAN menu and press Enter.
9. Select the settings on the Wireless LAN menu as necessary for your network.
10. When you finish selecting settings, select Complete and follow the on-screen instructions to save
your settings and exit the menus.
After you complete the wireless settings for your projector, you need to select the wireless network on
your computer, or iOS or Android device.
Wireless LAN Menu Settings
Parent topic: Wireless Network Projection
Wireless LAN Menu Settings
Setting Options Description
Connection Mode Quick
Advanced
Selects the type of wireless
connection:
Quick: lets you connect to
multiple smartphones, tablets, or
computers directly
Advanced: lets you connect to
multiple smartphones, tablets, or
computers via a wireless network
access point
62
Setting Options Description
Search Access Point To Search View Search for available wireless
network access points in
Advanced connection mode
SSID Up 32 alphanumeric characters Sets the SSID (network name) of
the wireless LAN system the
projector is connecting to
Security Open
WPA2-PSK
WPA/WPA2-PSK
WPA2-EAP
WPA/WPA2-EAP
Selects the type of wireless
security used in the wireless
network (some options are only
available when the Connection
Mode setting is set to
Advanced)
Passphrase Between 8 to 63 alphanumeric
characters
Enter a paraphrase for the
wireless network
EAP Method EAP Type
User name
Password
Client Certificate
Verify Server Cert.
CA certificate
RADIUS Serv.Name
Sets the EAP settings for WPA2-
EAP and WPA/WPA2-EAP
security
Channel 1ch
6ch
11ch
In Quick connection mode,
selects the frequency band
(channel) used by the wireless
LAN
63
Setting Options Description
IP Settings DHCP
IP Address
Subnet Mask
Gateway Address
Turns on DHCP if your network
assigns addresses automatically;
set to Off to manually enter the
network's IP Address,Subnet
Mask, and Gateway Address
(some options are only available
when the Connection Mode
setting is set to Advanced)
SSID Display On
Off
Selects whether to display the
SSID on the network standby
screen
IP Address Display On
Off
Selects whether to display the IP
address on the network standby
screen
IPv6 Settings IPv6
Auto Configuration
Use Temporary Address
Selects the IPv6 settings when
you connect the projector to the
network using IPv6
Parent topic: Selecting Wireless Network Settings Manually
Selecting Wireless Network Settings in Windows
Before connecting to the projector, select the correct wireless network on your computer.
1. To access your wireless utility software, access the Desktop and double-click the network icon on
the Windows taskbar.
2. Do one of the following:
• If your projector is set up on an existing network (Advanced mode), select the network name
(SSID).
• If your projector is configured for Quick mode, select the projector's SSID.
3. Click Connect.
Parent topic: Wireless Network Projection
64
Selecting Wireless Network Settings on Mac
Before connecting to the projector, select the correct wireless network on your Mac.
1. Click the AirPort icon on the menu bar at the top of the screen.
2. Make sure AirPort is turned on, then do one of the following:
• If your projector is set up on an existing network (Advanced mode), select the network name
(SSID).
• If your projector is configured for Quick mode, select the projector's SSID.
Parent topic: Wireless Network Projection
Setting Up Wireless Network Security
You can set up security for your projector to use on a wireless network. Set up one of the following
security options to match the settings used on your network:
• WPA2-PSK (Advanced and Quick connection mode)
• WPA2-EAP (Advanced mode)
• WPA/WPA2-PSK (Advanced connection mode)
• WPA/WPA2-EAP (Advanced connection mode)
Note: Contact your network administrator for guidance on entering the correct information.
1. If you want to set up WPA2-EAP or WAP/WAP2-EAP security, make sure your digital certificate file
is compatible with projector registration and placed directly on a USB storage device.
2. Press the Menu button.
65
3. Select the Network menu and press Enter.
4. Select Network Configuration and press Enter.
5. Select the Wireless LAN menu and press Enter.
6. Set the Security setting to match your network settings.
7. Do one of the following depending on the network security setting you selected:
•WPA2-PSK or WPA/WPA2-PSK: Select Complete and follow the on-screen instructions to save
your settings and exit the menus. Skip the remaining steps.
•WPA2-EAP or WPA/WPA2-EAP: Select EAP Method and press Enter.
66
8. Select your authentication protocol as the EAP Type setting.
9. To import your certification, select the certificate type (either Client Certificate or CA certificate)
and press Enter.
Note: You can also register a digital certificate from your web browser. Make sure to register just
once or the certificate may not install correctly.
10. Select Register and press Enter.
11. Follow the on-screen instructions to connect a USB storage device to the projector's USB-A port.
12. Press Enter to display the certificate list.
13. Select the certificate to import from the displayed list.
You see a message to enter the certificate password.
14. Enter a password and press Enter.
You see a completion message after the certificate is imported.
15. Set the following EAP settings as necessary:
•User name lets you enter a user name up to 64 alphanumeric characters long. To enter more than
32 characters, use your web browser.
•Password lets you enter a password up to 64 alphanumeric characters long when using the
PEAP, EAP-FAST, or LEAP protocols. To enter more than 32 characters, use your web browser.
•Verify Server Cert. lets you select whether or not to verify the server certificate when a CA
certificate has been set.
•RADIUS Serv.Name lets you enter the server name to be verified.
16. When you finish selecting settings, select Complete and follow the on-screen instructions to save
your settings and exit the menus.
Parent topic: Wireless Network Projection
Related references
Wireless LAN Menu Settings
Setting Up Projector Network E-Mail Alerts
You can set up the projector to send you an e-mail alert over the network if there is a problem with the
projector.
1. Press the Menu button.
67
2. Select the Network menu and press Enter.
3. Select Network Configuration and press Enter.
4. Select the Notifications menu and press Enter.
5. Turn on Mail Notification.
6. Enter the IP address for the SMTP Server setting.
Note: Do not use these addresses: 127.x.x.x or 224.0.0.0 through 255.255.255.255 (where x is a
number from 0 to 255).
7. Select a number for the SMTP server Port Number setting, from 1 to 65535 (default is 25).
8. Enter the sender's email address as the From setting.
9. Choose an Address Setting field, enter the e-mail address, and select or deselect the alerts you
want to receive there. Your e-mail address can be up to 32 alphanumeric characters long. Repeat
for up to three addresses.
10. If you are using the PJLink protocol for projector control, turn on the PJLink Notification setting and
enter the IP address where you want to receive PJLink notifications as the Notified IP Address
setting.
11. When you finish selecting settings, select Complete and follow the on-screen instructions to save
your settings and exit the menus.
68
Note: If a critical problem causes a projector to shut down, you may not receive an e-mail alert.
Network Projector E-mail Alert Messages
Parent topic: Using the Projector on a Network
Network Projector E-mail Alert Messages
When a problem occurs with a networked projector, and you selected to receive e-mail alerts, you
receive an e-mail containing the following information:
• The email address entered as the From setting
•Epson Projector on the subject line
• The name of the projector experiencing a problem
• The IP address of the affected projector
• Detailed information about the problem
Note: If a critical problem causes a projector to shut down, you may not receive an e-mail alert.
Parent topic: Setting Up Projector Network E-Mail Alerts
Selecting Other Network Settings
You can select optional network settings on the Others menu.
1. Press the Menu button.
2. Select the Network menu and press Enter.
3. Select Network Configuration and press Enter.
69
4. Select the Others menu and press Enter.
5. If you want to use the Secure HTTP protocol to encrypt communication when using Web Control,
turn on the Secure HTTP setting and import the web server certificate using the Web Server Cert.
setting.
6. Select the Priority Gateway setting for your network.
7. If your network environment uses an AMX controller, turn on the AMX Device Discovery setting to
allow the projector to be detected.
8. If your network environment uses a Crestron Connected controller, turn on the Crestron Connected
setting to allow the projector to be detected.
Note: Enabling Crestron Connected disables the Message Broadcasting feature in the Epson
Projector Management software (Windows only).
9. If you want to control the projector using Art-Net (an Ethernet communication protocol based on
TCP/IP), turn on the Art-Net setting.
10. If you want this projector to receive broadcasted messages over the network, turn on the Message
Broadcasting setting. Administrators can broadcast messages over the network using the Epson
Projector Management software (Windows only).
11. When you finish selecting settings, select Complete and follow the on-screen instructions to save
your settings and exit the menus.
Parent topic: Using the Projector on a Network
70
Related concepts
Using Crestron Connected
Related references
Art-Net Channel Definitions
Additional Projector Software and Manuals
Setting a Static IP Address on the LCD Screen
You can set a static IP address on the projector's LCD screen while the projector is in standby mode.
This lets you set the address without needing to project anything.
1. Press the Menu button on the projector or remote control.
2. Select the Extended menu and press Enter.
3. Select the A/V Settings >A/V Output, select Always On, and press Enter.
4. Select Standby Mode, select Communication On, and press Enter.
5. Press the Menu button to exit the menu system.
6. Turn off the projector, connect it to a wired LAN, and turn on the power using the power switch.
7. Hold down the HDBaseT/LAN button on the projector control panel for at least three seconds.
71
You see the static IP setting menu:
8. Press the Enter button on the projector control panel, press the down arrow button to select OFF as
the DHCP setting, and press Enter again.
9. Use the up and down arrow buttons as necessary to change the IP address values. Use the left and
right arrow buttons to move the cursor to the next or previous number position. When you finish,
press Enter.
Note: You can also enter the numbers using the numeric buttons on the remote control.
10. Repeat the last step to enter the subnet mask and gateway address, if necessary, and press Enter.
11. Press Enter to select Finish and return to the status information screen.
Parent topic: Using the Projector on a Network
Related references
Projector Parts - Control Panel
Related tasks
Selecting Wired Network Settings
Controlling a Networked Projector Using a Web Browser
Once you have connected your projector to your network, you can select projector settings and control
projection using a compatible web browser. This lets you access the projector remotely.
Note: The web setup and control features support Microsoft Internet Explorer 11.0 or later, Microsoft
Edge, Google Chrome, and Safari on networks that do not use a proxy server for connection. You
cannot select all of the projector menu settings or control all projector functions using a web browser.
72
Note: If you set Standby Mode to Communication On, you can use a web browser to select settings
and control projection even if the projector is in standby mode.
1. Make sure the projector is turned on.
2. Start your web browser on a computer or device connected to the network.
3. Type the projector's IP address into the browser's address box and press the computer's Enter key.
Note: You may need to log in to access some of the options on the Web Control screen. If you see a
log in window, enter your user name and password. (The default user name is EPSONWEB and the
default password is admin.)
You see the Epson Web Control screen.
1 Select Basic Control to control the projector remotely.
2 Select Test Pattern to display a test pattern
3 Select Crestron Connected to open the menu (if you enabled Crestron Connected in the
Network >Others menu)
4 Select Advanced to open the advanced menu screen.
5 Select Status Information to view the projector's status.
6 Select Remote Camera Access to take an image capture of the displayed image from a
remote location
73
7 Select Lens Control to adjust the lens (focus, zoom, and lens shift).
8 Select OSD Control Pad to change the projector's menu settings.
4. Select the option corresponding to the projector function you want to control.
Web Control Options
Viewing an Image Capture of the Displayed Image from a Remote Location
Parent topic: Using the Projector on a Network
Related tasks
Selecting Other Network Settings
Web Control Options
Basic Control
Note: If the Remote Password is set to On, you need to enter your user name and password. (The
default username is EPSONREMOTE and the default password is guest).
1 Turns on the projector (power on)
2 Input source selection controls
3 Turns off the image temporarily
4 Searches for sources
74
5 Turns off the projector (standby)
OSD Control Pad
1 Returns to the Home screen
2 Displays the projector's setting menus
3 Use your finger or mouse to navigate the menus
4 Returns settings to their default values
5 Returns to the previous menu (if this doesn't work, select Home)
6 Displays help topics
Note: You cannot change some settings using Epson Web Control.
75
Lens Control
Focus/Distortion screen
Note: Depending on the currently installed lens, this screen may look different.
1 Returns to the Home screen
2 Focus adjustment slider
3 Focus adjustment buttons
4 Distortion adjustment slider
5 Distortion adjustment buttons
6 Displays the Focus/Distortion screen
7 Displays the Zoom screen
8 Displays the Lens Shift screen
9 Displays the Test Pattern screen
10 Displays the Memory screen
Zoom screen
76
Note: Zoom is not available for the ELPLX02 and ELPLX02W lenses.
Note: Depending on the currently installed lens, this screen may look different.
1 Zoom adjustment slider
2 Zoom adjustment buttons
Lens Shift screen
Note: Depending on the currently installed lens, this screen may look different.
77
1 The blue square displays the current image position and the red square displays the new image
position
2 Displays the vertical image position; select to change the value
3 Moves the image position up, down, left, or right
4 Moves the lens to the home position
5 Displays the horizontal image position; select to change the value
Test Pattern screen
1 Displays available test patterns; select to project a test pattern
2 Turns off test pattern display
78
Memory screen
1 Overwrites your current settings with saved settings
2 Saves your current settings to memory
3 Displays a list of saved memories
4 Erases a saved memory
5 Renames a saved memory
Status Information screen
79
1 Returns to the Home screen
2 Displays a list of monitored settings
3 Displays the setting status
4 Select to view different status information
Remote Camera Access screen
1 Displays the image you captured using the Shoot button
2 Takes a picture of the projected image using the camera on the front of the projector
3 Adjusts the image exposure
4 Zooms in or out on the image you captured
Parent topic: Controlling a Networked Projector Using a Web Browser
Related tasks
Viewing an Image Capture of the Displayed Image from a Remote Location
Viewing an Image Capture of the Displayed Image from a Remote Location
You can take an image capture of the projected image and view it from a remote location using the
projector's built-in camera.
80
Note the following when using this feature:
• This feature is not supported with the ELPLX02 or ELPLX02W lens.
• This feature is not supported when performing the following functions: Tiling, Tiling Assist, Screen
Matching, Color Calibration, Lens Calibration, Message Broadcasting in the Epson Projector
Management software.
• Using this feature cancels the following functions: Split Screen, Shutter, on-screen display (when the
message is hidden).
1. Hold down the Freeze button on the remote control for about five seconds or until you see this
menu.
2. Make sure the Remote Camera Access setting is set to Off, then exit the menu.
3. Press the Menu button.
4. Select the Network menu and press Enter.
81
5. Select Network Configuration and select the Others menu.
6. Make sure the Secure HTTP setting is enabled and return to the Network menu.
7. Select Remote Camera Access and press Enter.
You see a screen like this:
8. Select On as the Remote Camera Access setting.
9. Select the Password setting and enter a password up to 32 alphanumeric characters long.
Note: Do not use these characters in the password: * (asterisk), : (colon), or a space character.
10. Open a web browser on a computer or mobile device connected to the projector over a network
connection.
11. Enter the projector's IP address in your browser's address box to connect to Epson Web Control.
82
You see a screen like this:
Note: You can view the projector's IP address by selecting Net. Info. - Wireless LAN or Net. Info. -
Wired LAN on the Network menu.
12. Select Remote Camera Access.
Note: You may need to log in to access some of the options on the Epson Web Control screen. If
you see a log in window, enter your user name and password. (The default user name is
EPSONWEB and the default password is admin.)
83
13. Click Shoot to take a capture of the projected image. (You cannot capture warning or caution
messages.)
Note: If you see a password screen, enter the password you selected for remote camera access.
You cannot perform any projector operations during shooting other than turning off the projector.
The projector displays a message on the projection screen for several seconds while it takes an
image capture. When finished, the captured image is displayed in the area above the Shoot button.
Parent topic: Controlling a Networked Projector Using a Web Browser
Using Crestron Connected
If you are using the Crestron Connected network monitoring and control system, you can set up your
projector for use on the system. Crestron Connected lets you control and monitor your projector using a
web browser.
Note: You cannot use the Message Broadcasting feature in the Epson Projector Management software
when you use Crestron Connected.
For additional information on Crestron Connected, contact Crestron.
Setting Up Crestron Connected
Controlling a Networked Projector Using Crestron Connected
84
Parent topic: Using the Projector on a Network
Related references
Additional Projector Software and Manuals
Setting Up Crestron Connected
To set up your projector for monitoring and control using a Crestron Connected system, make sure your
computer and projector are connected to the network.
Note: If you want to use the Crestron Connected system when the projector is turned off, you need to
adjust the Standby Mode settings in the Extended menu.
1. Press the Menu button.
2. Select the Network menu and press Enter.
3. Select Network Configuration and press Enter.
4. Select the Others menu and press Enter.
5. Set the Crestron Connected setting to On to allow the projector to be detected.
Note: Enabling Crestron Connected disables the Message Broadcasting feature in the Epson
Projector Management software.
6. Turn off the projector, then turn it on again to enable the setting.
85
Parent topic: Using Crestron Connected
Related references
Projector Setup Settings - Extended Menu
Controlling a Networked Projector Using Crestron Connected
Once you have set up your projector to use Crestron Connected, you can control and monitor projection
using a compatible web browser.
1. Start your web browser on a computer connected to the network.
2. Type the projector's IP address into the browser's address box and press the computer's Enter key.
You see the Epson Web Control screen:
3. Select Crestron Connected.
86
You see a screen like this:
Note: Sources in the image above vary depending on ports available on your product.
4. Select the input source that you want to control in the Sources List box. You can scroll through
available sources using the up and down arrows in the box.
5. To control projection remotely, click the on-screen buttons that correspond to the projector's remote
control buttons. You can scroll through button options at the bottom of the screen.
Note: These on-screen buttons do not directly correspond to the projector's remote control buttons:
•OK acts as the Enter button
•Menu displays the projector's menu
6. To view information about the projector, click the Info tab.
7. To change projector, Crestron, and password settings, click the Tools tab, select settings on the
displayed screen, and click Send.
8. When you finish selecting settings, click Exit to exit the program.
Parent topic: Using Crestron Connected
87
Art-Net Channel Definitions
Art-Net is an Ethernet communication protocol based on the TCP/IP protocol. You can control the
projector by using a DMX controller or an application system.
The following table lists the channel definitions used to control the projector in Art-Net.
Begin by setting channel 13 to Can control.
Note: When controlling the projector using Art-Net and performing operations from the remote control or
control panel, settings made by the DMX controller or application software may not be applied to the
projector correctly or may differ from the projector's actual status. If you want to apply control for multiple
channels to the projector, set Channel 13 to Cannot control before you make any other settings. Then
set Channel 13 to Can control after setting multiple channels. You can then control the projector without
changing the setting for Channel 13.
Channel/Function Operation Parameters Description
1 Adjusting light
(dimming)
0% to 100% 0 to 255 Adjusts the image
brightness (default is
0)
2 Shutter control Shutter closed
Non-operational
Shutter open
0 to 63
64 to 191
192 to 255
Closes and opens
the shutter (default is
128)
88
Channel/Function Operation Parameters Description
3 Switch source Non-operational 0 to 23, 32 to 47, 64 to 71,
88 to 127, 144 to 167, 184
to 255
Switches to the
specified source
(default is 0)
HDBaseT 24 to 31
SDI 48 to 55
Computer 56 to 63
BNC 72 to 79
LAN 80 to 87
Slot 1-1* 128 to 135
Slot 1-2* 136 to 143
Slot 2-1* 168 to 175
Slot 2-2* 176 to 183
4 Lens position Non operational
Move to home position
0 to 31, 64 to 255
32 to 63
Shifts the lens to the
home position
(default is 0)
5 Horizontal lens
shift
(+) Lens adjustment Movement - large: 0 to 31
Movement - medium: 32 to
63
Movement - small: 64 to
95
Shifts the lens
horizontally by the
amount of shift
specified (default is
128)
Non-operational 96 to 159
(–) Lens adjustment Movement - small: 160 to
191
Movement - medium: 192
to 223
Movement - large: 224 to
255
89
Channel/Function Operation Parameters Description
6 Vertical lens shift (+) Lens adjustment Movement - large: 0 to 31
Movement - medium: 32 to
63
Movement - small: 64 to
95
Shifts the lens
vertically by the
amount of shift
specified (default is
128)
Non-operational 96 to 159
(–) Lens adjustment Movement - small: 160 to
191
Movement - medium: 192
to 223
Movement - large: 224 to
255
7 Electronic zoom (+) Lens adjustment Movement - large: 0 to 31
Movement - medium: 32 to
63
Movement - small: 64 to
95
Zooms using the
specified amount of
movement (default is
128)
Non-operational 96 to 159
(–) Lens adjustment Movement - small: 160 to
191
Movement - medium: 192
to 223
Movement - large: 224 to
255
90
Channel/Function Operation Parameters Description
8 Electronic focus (+) Lens adjustment Movement - large: 0 to 31
Movement - medium: 32 to
63
Movement - small: 64 to
95
Performs electronic
focus using the
specified amount of
movement (default is
128)
Non-operational 96 to 159
(–) Lens adjustment Movement - small: 160 to
191
Movement - medium: 192
to 223
Movement - large: 224 to
255
9 Electronic
distortion
(+) Lens adjustment Movement - large: 0 to 31
Movement - medium: 32 to
63
Movement - small: 64 to
95
Corrects distortion
using the specified
amount of movement
(default is 128)
Non-operational 96 to 159
(–) Lens adjustment Movement - small: 160 to
191
Movement - medium: 192
to 223
Movement - large: 224 to
255
91
Channel/Function Operation Parameters Description
10 Load lens
memory
Non-operational 0 to 15, 176 to 255 Loads the specified
lens memory (default
is 0)
Load lens memory 1 16 to 31
Load lens memory 2 32 to 47
Load lens memory 3 48 to 63
Load lens memory 4 64 to 79
Load lens memory 5 80 to 95
Load lens memory 6 96 to 111
Load lens memory 7 112 to 127
Load lens memory 8 128 to 143
Load lens memory 9 144 to 159
Load lens memory 10 160 to 175
11 Power control Power off
Non-operational
Power on
0 to 63
64 to 191
192 to 255
Turns the projector
power on or off
(default is 128)
12 Geometry
correction
Off 0 to 15 Performs geometry
correction (default is
255)
H/V-Keystone 16 to 31
Quick Corner 32 to 47
Point Correction 48 to 63
Curved Surface 64 to 79
Corner Wall 80 to 95
Load geometry correction
memory 1
96 to 111 Loads a geometry
correction memory
(default is 255)
Load geometry correction
memory 2
112 to 127
Load geometry correction
memory 3
128 to 143
Non-operational 144 to 175
92
Channel/Function Operation Parameters Description
13 Lock Cannot control
Can control
0 to 127
128 to 255
Enables/disables Art-
Net operations
(default is 0)
14 Freeze Non-operational 0 to 31, 96 to 159, 224 to
255
Pauses or resumes
image display
(default is 128)
Freeze off 32 to 95
Freeze on 160 to 223
* The slot number of the interface board followed by the port number from left to right on the interface
board
Parent topic: Using the Projector on a Network
Related tasks
Selecting Other Network Settings
Registering a Digital Certificate on the Projector
Follow the instructions here if you need to install a digital certificate on the projector to provide security
for your presentation files.
Note: You can register a digital certificate over a network or from a connected USB device. However, be
sure to register just once from either a USB device or network, or the certificate may not install correctly.
Importing a Web Server Certificate Using the Projector Menus
Registering Digital Certificates from a Web Browser
Digital Certificate Types
Parent topic: Using the Projector on a Network
Importing a Web Server Certificate Using the Projector Menus
You can create your web server certificate and import it using the projector menus and a USB flash
drive.
Note: You can also register digital certificates from your web browser. Make sure to only register once,
or the certificate may not install correctly.
93
1. Make sure your digital certificate file is compatible with projector registration and saved in the root
directory of the USB flash drive.
2. Press the Menu button on the remote control.
3. Select the Network menu and press Enter.
4. Select the Network Configuration setting and press Enter.
5. Select the Others menu and press Enter.
6. Select On as the Secure HTTP setting.
7. Select the Web Server Cert. setting and press Enter.
8. Select Register and press Enter.
9. Insert a USB flash drive into the projector's USB-A port.
10. Press Enter to display the certificate list.
11. Select the certificate you want to import from the displayed list.
A message is displayed prompting you to enter the password for the certificate.
12. Enter the password and press Enter.
The certificate is imported and a completion message appears.
Parent topic: Registering a Digital Certificate on the Projector
Related references
Digital Certificate Types
94
Registering Digital Certificates from a Web Browser
You can register the digital certificates on the projector for wireless LAN authentication.
1. Make sure your digital certificate file is compatible with projector registration.
2. Make sure the projector is turned on.
3. Start your web browser on a computer or mobile device connected to the network.
4. Type the projector's IP address into the browser's address box and press the computer's Enter key.
You see the Web Control screen:
5. Select Advanced.
Note: You may need to log in to access some of the options on the Web Control screen. If you see a
log in window, enter your user name and password. (The default user name is EPSONWEB and the
default password is admin.)
6. Under Network, select Certificate.
7. Click the Choose File button, select the certificate file, and click Open.
8. Enter a password in the Password box and click Send.
9. When you finish registering the certificate, click Apply to finalize your changes and complete the
registration.
Parent topic: Registering a Digital Certificate on the Projector
95
Related references
Digital Certificate Types
Digital Certificate Types
You can register these types of digital certificates.
Client Certificate (PEAP-TLS/EAP-TLS)
Specification Description
Format PKCS#12
Extension PFX/P12
Encryption RSA
Hashes MD5/SHA-1/SHA-256/SHA-384/SHA-512
Key length 512/1024/2048/4096 bit
Password Up to 32 alphanumeric characters; required
CA Certificate (PEAP/PEAP-TLS/EAP-TLS/EAP-FAST)
Specification Description
Format X509v3
Extension DER/CER/PEM
Encryption RSA
Hashes MD5/SHA-1/SHA-256/SHA-384/SHA-512
Key length 512/1024/2048/4096 bit
Encoding BASE64/Binary
Web Server Certificate (Secure HTTP)
Specification Description
Format PKCS#12
Extension PFX/P12
Encryption RSA
96
Specification Description
Hashes MD5/SHA-1/SHA-256/SHA-384/SHA-512
Key length 512/1024/2048/4096 bit
Common name Network host name
Organization Optional
Password Up to 32 alphanumeric characters; required
Note: You can set a password of up to 64 characters if you use a web browser to enter the text.
Parent topic: Registering a Digital Certificate on the Projector
97
Using Basic Projector Features
Follow the instructions in these sections to use your projector's basic features.
Turning On the Projector
Turning Off the Projector
Selecting the Language for the Projector Menus
Adjusting the Image Height
Resizing the Image with the Zoom Button
Focusing the Image Using the Focus and Distortion Buttons
Setting the Screen Type
Adjusting the Image Position Using Lens Shift
Adjusting the Image Position Using Screen Position
Displaying a Test Pattern
Image Shape
Selecting an Image Source
Remote Control Operation
Projection Modes
Image Aspect Ratio
Color Mode
Adjusting the Brightness
Adjusting Luminance Controls
Adjusting Gamma
Setting the Date and Time
Turning On the Projector
Turn on the computer or video equipment you want to use before you turn on the projector so it can
display the image source.
Note: Install a circuit breaker for 13 A to 20 A to the wiring that supplies power to the projector and do
not connect any other devices to that wiring.
98
1. Connect the power cord to the projector's power inlet. Flip the power cable holder over the plug as
shown.
Note: If you connected the projector using the 100 V power cord, the image brightness is reduced to
approximately 55% of the brightness achievable with the 220 V power cord and the Laser light
flashes orange. For optimal performance, connect the 220 V power cord that came with the
projector. You cannot access the Light Source Mode,Estimated Remains, or Light Source
Calibration menu settings when connected using the 100 V power cord.
2. Plug the power cord into an electrical outlet.
3. Turn on the power switch on the side of the projector.
The projector's On/Standby light flashes briefly and then turns blue. This indicates that the projector
is receiving power.
99
Note: With Direct Power On turned on, the projector turns on as soon as you plug it in.
4. Press the On button on the projector or remote control to turn on the projector.
The projector beeps and the Status light flashes blue as the projector warms up. After about 30
seconds, the Status light stops flashing and turns blue.
Warning: Never look into the projector lens when the laser is on. This can damage your eyes and is
especially dangerous for children and pets.
Caution: Make sure no objects are blocking the light from the projector lens. Objects blocking the
lens for an extended time can melt and light that is reflected back into the lens can cause the
projector to malfunction.
If you do not see a projected image right away, try the following:
• Make sure the lens cap is off.
• Turn on the connected computer or video device.
• Insert a DVD or other video media and press the play button, if necessary.
• Press the Search button on the remote control to detect the video source, or press one of the source
buttons on the remote control or projector.
Parent topic: Using Basic Projector Features
Related references
Projector Setup Settings - Extended Menu
Related tasks
Turning Off the Projector
Turning Off the Projector
Before turning off the projector, shut down any computer connected to it so you can see the computer
display during shutdown.
Note: Turn off this product when not in use to prolong the life of the projector. Laser life will vary
depending upon mode selected, environmental conditions, and usage. Brightness decreases over time.
1. Press the Standby button on the projector or remote control.
100
The projector displays a shutdown confirmation screen.
2. Press the Standby button on the projector or remote control again. (To leave it on, press any other
button.)
The projector beeps twice, the laser turns off, and the Status light turns off.
Note: With Epson's Instant Off technology, there is no cool-down period so you can pack up the
projector for transport right away (if necessary).
3. Turn off the power using the power switch on the side of the projector.
The On/Standby light turns off.
4. To transport or store the projector, make sure the Status light is off, then unplug the power cord. (If
necessary, flip open the power cable holder first.)
101
Note: If you use the projector continuously for more than 24 hours, or regularly turn it off by shutting off
the power outlet, schedule periodic Light Source Calibration events in the Extended menu schedule
settings.
Parent topic: Using Basic Projector Features
Related references
Projector Setup Settings - Extended Menu
Related tasks
Turning On the Projector
Saving a Scheduled Event
Selecting the Language for the Projector Menus
If you want to view the projector's menus and messages in another language, you can change the
Language setting.
1. Turn on the projector.
2. Press the Menu button.
3. Select the Extended menu and press Enter.
4. Select the Language setting and press Enter.
5. Select the language you want to use and press Enter.
6. Press Menu or Esc to exit the menus.
102
Parent topic: Using Basic Projector Features
Adjusting the Image Height
If you are projecting from a table or other flat surface, and the image is too high or low, you can adjust
the image height using the projector's adjustable feet.
1. Turn on the projector and display an image.
2. To adjust the image height, or the projector's horizontal and vertical tilt, rotate the front or rear feet to
extend or retract them.
1 Extend the feet
2 Retract the feet
Note: You can adjust the projector's tilt up to 2°. You can also detach the feet or extend them up to
1.1 inches (28 mm) before they detach.
If the projected image is unevenly rectangular, you need to adjust the image shape.
Parent topic: Using Basic Projector Features
103
Related concepts
Image Shape
Resizing the Image with the Zoom Button
You can adjust the size of the image using the zoom buttons.
Note: Wait 30 minutes after turning on the projector before setting the focus, zoom, and lens shift for
maximum accuracy.
1. Turn on the projector and display an image.
2. Press the Zoom button on the control panel.
3. Press the left or right arrow buttons to resize the image.
4. Press the Esc button when finished.
Note: You can also press the Zoom + or –buttons on the remote control to adjust the size of the image.
Parent topic: Using Basic Projector Features
Focusing the Image Using the Focus and Distortion Buttons
You can adjust the sharpness of the projected image using the focus and distortion buttons.
Note: Wait 30 minutes after turning on the projector before setting the focus, zoom, and lens shift for
maximum accuracy.
1. Turn on the projector and display an image.
Note: If you are projecting from multiple projectors that differ in brightness, display a grayscale test
pattern to adjust the focus for best results.
104
2. Press the Focus button on the control panel.
3. Do one of the following depending on the type of lens you have installed:
•Non-short-throw zoom lens: Press the left and right arrow buttons to adjust the focus and press
the Esc button when finished. Skip the rest of these steps.
•Short-throw zoom lens: Press the left and right arrow buttons to focus the image around the
center of the lens. You may see a message prompting you to correct the image distortion.
Continue with the next steps.
4. Press the Distortion button on the control panel.
105
5. Press the left and right arrow buttons to focus the image in the surrounding area.
Note: You can also adjust image distortion using the Focus + or –and Distortion + or –buttons on
the remote control.
6. If the center becomes out of focus again, repeat steps 2 and 3.
If you still cannot correct the focus, press the Calibration button on the remote control to calibrate the
lens, then try focusing again.
Parent topic: Using Basic Projector Features
Related tasks
Displaying a Test Pattern
Setting the Screen Type
You can use the Screen Type setting to match the aspect ratio of the displayed image to the screen you
are using.
Note: The Screen Type setting is not supported by the Message Broadcasting feature in the Epson
Projector Management software.
1. Turn on the projector and display an image.
2. Press the Menu button.
3. Select the Extended menu and press Enter.
106
4. Select Display >Screen >Screen Type.
You see this screen:
5. Select your screen's aspect ratio and press Enter.
6. Press the Menu button to exit.
7. Adjust the aspect ratio for the projected image, if necessary.
Parent topic: Using Basic Projector Features
Related concepts
Image Aspect Ratio
Adjusting the Image Position Using Lens Shift
If you cannot install the projector directly in front of the screen, you can adjust the position of the
projected image using the lens shift feature.
Note: Wait 30 minutes after turning on the projector before setting the focus, zoom, and lens shift for
maximum accuracy.
1. Turn on the projector and display an image.
107
2. Press the Lens Shift button on the control panel or remote control.
3. Press the arrow buttons on the remote control or the control panel to adjust the position of the
projected image as necessary.
Note: When adjusting the image height, position the image lower than where you want it to be and
then move it up. This will help prevent the image from moving down after adjustment.
Here are the lens shift ranges for the optional lenses:
ELPLU04/ELPLW06/ELPLW08/ELPLM10/ELPLM11/ELPLM15/ELPLL08
108
1 Center of lens
2 Projected image when lens shift is set to the home position
3 Maximum motion range: V × 60%
ELPLX02/ELPLX02W
1 Center of lens
2 Projected image when lens shift is set to the home position
3 Maximum motion range: Up V × 20%, Down V × 5%
Note: You cannot move the image vertically when the lens is shifted horizontally all the way.
4. When you are finished, press the Esc button on the control panel or remote control.
Note: The image is clearest when the lens is at the home position. To move the lens to the home
position, press and hold the Lens Shift button on the remote control or control panel for at least three
seconds. Set the A/V Output setting in the Extended menu to Always On so you can move the lens to
the home position even when the projector is in standby mode.
Parent topic: Using Basic Projector Features
Related references
Projector Setup Settings - Extended Menu
109
Adjusting the Image Position Using Screen Position
You can adjust the image position if there are margins between the edge of the image and the projected
screen frame.
Note: You cannot adjust the screen position if the Screen Type setting is set to 16:10.
1. Turn on the projector and display an image.
2. Press the Menu button.
3. Select the Extended menu and press Enter.
4. Select Display >Screen >Screen Position.
5. Use the arrow buttons on the remote control or projector to adjust the position of the image.
6. When you are finished, press the Menu button.
Parent topic: Using Basic Projector Features
Related tasks
Setting the Screen Type
Displaying a Test Pattern
You can display a test pattern to adjust the projected image without connecting a computer or video
device.
Note: The test pattern's shape is determined by the Screen Type setting. Be sure to set the correct
screen type before adjusting with the test pattern.
110
1. Turn on the projector.
2. Press the Test Pattern button on the remote control or control panel.
3. Press the left or right arrow button on the remote control, or press Enter on the control panel to cycle
through the available test patterns.
4. Adjust the image as necessary.
5. Press the Esc button to clear the test pattern.
Parent topic: Using Basic Projector Features
Related tasks
Setting the Screen Type
Image Shape
You can project an evenly rectangular image by placing the projector directly in front of the center of the
screen and keeping it level. If you place the projector at an angle to the screen, or tilted up or down, or off
to the side, you may need to correct the image shape for the best display quality.
Correcting Image Shape with H/V Keystone
Correcting Image Shape with Quick Corner
Correcting Image Shape with Curved Surface
Correcting Image Shape with Corner Wall
Correcting Image Shape with Point Correction
Parent topic: Using Basic Projector Features
Correcting Image Shape with H/V Keystone
You can use the projector's H/V Keystone setting to correct the shape of an image that is unevenly
rectangular on the sides.
111
Note: You cannot combine H/V Keystone correction with other image shape correction methods.
1. Turn on the projector and display an image.
2. Press the Geometry button on the projector control panel or remote control.
3. Select the H/V-Keystone setting and press Enter. Then press Enter again.
You see the H/V-Keystone adjustment screen:
Note: You can also access the H/V Keystone setting by pressing the Menu button and selecting
Geometry Correction on the Settings menu.
4. Use the arrow buttons on the projector or the remote control to select between vertical and
horizontal keystone or balance correction and to adjust the image shape as necessary.
V-Keystone
V-Balance
112
H-Keystone
H-Balance
5. When you are finished, press the Menu button.
After correction, your image may be slightly smaller.
Parent topic: Image Shape
Related references
Projector Feature Settings - Settings Menu
Correcting Image Shape with Quick Corner
You can use the projector's Quick Corner setting to correct the shape and size of an image that is
unevenly rectangular on all sides.
113
1. Turn on the projector and display an image.
2. Press the Geometry button on the projector control panel or remote control.
3. Select Quick Corner and press Enter.
You see the Quick Corner adjustment screen:
Note: You can also access the Quick Corner setting by pressing the Menu button and selecting
Geometry Correction on the Settings menu.
4. Use the arrow buttons on the projector or remote control to select the corner of the image you want
to adjust. Then press Enter.
5. Press the arrow buttons to adjust the image shape as necessary.
Note: To reset your adjustments, press and hold the Esc button for at least 2 seconds to display a
reset screen. Then select Yes and press Enter.
6. When you are finished, press the Menu button.
Parent topic: Image Shape
Related references
Projector Feature Settings - Settings Menu
114
Correcting Image Shape with Curved Surface
You can use the projector's Curved Surface setting to adjust the shape of an image projected on a
curved surface.
Note: For the best results, project from the front of the screen onto a surface with a uniform arc radius
and with the lens in the home position.
1. Turn on the projector and display an image.
2. Press the Geometry button on the projector control panel or remote control.
3. Select the Curved Surface setting and press Enter. If you see a confirmation message, press Enter
again.
You see this screen:
115
Note: You can also access the Curved Surface setting by pressing the Menu button and selecting
Geometry Correction on the Settings menu.
4. Select Curved Surface again and press Enter.
5. Select the Correct Shape setting and press Enter.
You see a screen like this:
6. Use the arrow buttons on the projector or the remote control to select the area you want to adjust.
Then press Enter.
7. Use the arrow buttons on the projector control panel or remote control to adjust the image shape.
116
Note: If the adjustment triangle turns gray, you cannot adjust the shape any further in that direction.
8. Press the Esc button to return to the Curved Surface menu screen.
9. Repeat the previous three steps as necessary to adjust other image areas.
If the image expands or contracts, continue with the next steps to adjust the linearity.
Note: To reset your adjustments, press and hold the Esc button for at least 2 seconds to display a
reset screen. Then select Yes and press Enter.
10. Press the Esc button.
You see this screen:
11. To compensate for expansion or contraction while maintaining the image aspect ratio, select
Maintain Aspect Ratio and set it to On.
12. Select one of the following to adjust the linearity:
•Horizontal Linearity: Adjusts horizontal expansion or contraction.
•Vertical Linearity: Adjusts vertical expansion or contraction.
13. Use the arrow buttons to select a displayed line to use as a baseline and press Enter.
The selected baseline flashes orange and white.
117
14. Adjust the linearity by doing one of the following:
• Press the left arrow button to contract the distance between the lines closest to the baseline.
118
• Press the right arrow button to expand the distance between the lines closest to the baseline.
15. When you are finished, press the Menu button.
Note: If necessary, you can adjust the image tilt using the Quick Corner setting, then fine-tune your
adjustments using the Point Correction setting.
Parent topic: Image Shape
Related references
Projector Feature Settings - Settings Menu
Related tasks
Correcting Image Shape with Quick Corner
Correcting Image Shape with Point Correction
119
Correcting Image Shape with Corner Wall
You can use the projector's Corner Wall setting to adjust the shape of an image projected on a surface
with right angles, such as a rectangular pillar or the corner of a room.
Note: For the best results, project from the front of the screen onto a right-angled surface. The image
may not be evenly focused throughout even after performing the steps here.
1. Turn on the projector and display an image.
2. Press the Geometry button on the projector control panel or remote control.
3. Select the Corner Wall setting and press Enter.
Note: If you see a confirmation message, press Enter.
You see this screen:
4. Select Corner Wall again and press Enter.
5. Select the Corner Type setting and press Enter.
120
6. Select one of the following:
•Horizontal Corner when the surfaces line up horizontally
•Vertical Corner when the surfaces line up vertically
7. Press the Esc button to return to the Corner Wall menu screen.
8. Select the Correct Shape setting and press Enter.
9. Adjust the projector's position and use lens shift to center the image over the point where the two
surfaces meet. (The rest of these steps show Horizontal Corner as the selected Corner Type but the
steps are the same for Vertical Corner.)
121
Note: You can press Enter to show or hide the image and grid to check the results.
10. Press the arrow buttons on the projector or the remote control to select the area you want to adjust.
Then press Enter.
• For horizontal corners, adjust the top area using the lowest point (1) as your reference. Adjust the
lower area using the highest point (2) as your reference.
• For vertical corners, adjust the left and right areas using the points nearest the center of the image
as your reference points.
122
11. Press the arrow buttons on the projector or remote control to adjust the image shape.
Note: To reset your adjustments, press and hold the Esc button for at least 2 seconds to display a
reset screen. Then select Yes.
12. Repeat the previous two steps as necessary to adjust other image areas.
13. If the image expands or contracts, press the Esc button to return to the Corner Wall screen so you
can adjust the linearity.
14. When you are finished, press the Menu button.
Note: If necessary, you can adjust the image tilt using the Quick Corner setting, then fine-tune your
adjustments using the Point Correction setting.
Parent topic: Image Shape
Related tasks
Correcting Image Shape with Quick Corner
Correcting Image Shape with Point Correction
Correcting Image Shape with Point Correction
You can use the projector's Point Correction feature to fine-tune the image shape using points on a grid.
This is useful for adjusting overlapping areas in multiple projected images that do not line up correctly.
Note: You can move the points on the grid between 0.5 to 32 pixels in any direction.
1. Turn on the projector and display an image.
2. Press the Geometry button on the projector control panel or remote control.
3. Select the Point Correction setting and press Enter.
Note: If you see a confirmation message, press Enter.
123
4. Select the Point Correction setting again and press Enter.
You see this screen:
5. Select the Point Correction setting and press Enter.
6. Select the number of grid lines to display and press Enter.
Note: If you need to change the color of the grid lines, select the Pattern Color setting and select a
suitable color.
7. Press the arrow buttons on the projector or remote control to move to the point on the grid that you
want to adjust. Then press Enter.
124
8. Press the arrow buttons to correct the image shape in all necessary directions.
Note: You can press Enter to show or hide the image and grid to check the results.
9. Press Esc to return to the previous screen and select another point to correct, if necessary.
10. When you are finished, press the Menu button.
Note: If necessary, you can fine-tune your image adjustments using the Quick Corner setting.
Parent topic: Image Shape
Related tasks
Correcting Image Shape with Quick Corner
Selecting an Image Source
If you connected multiple image sources to the projector, such as a computer and DVD player, you may
want to switch from one image source to the other.
1. Make sure the connected image source you want to use is turned on.
2. For video image sources, insert a DVD or other video media and press its play button, if necessary.
3. Do one of the following:
• Press the Search button on the remote control until you see the image from the source you want.
125
• Press the button for the source you want on the remote control. If there is more than one port for
that source, press the button again to cycle through the sources.
1 HDBaseT port source
2 HDMI source
3 Computer or BNC port source
4 DisplayPort source (if optional DisplayPort interface board is installed)
5 SDI port source
6 Network source
7 Input ports on the optional interface board in Slot 2
8 Input ports on the interface board in Slot 1
9 DVI-D source
• Press the button for the source you want on the projector control panel. If there is more than one
port for that source, press the button again to cycle through the sources.
126
1 HDMI or DVI-D source
2 HDBaseT port or network source
3 SDI port source
4 Computer or BNC port source
5 Input ports on the interface board in Slot 1
6 Input ports on the optional interface board in Slot 2
The Sync. light on the control panel turns on for the currently selected input source.
Parent topic: Using Basic Projector Features
Remote Control Operation
The remote control lets you control the projector from almost anywhere in the room, up to 98.4 feet
(30 m) away. You can point it at the front or rear of the projector.
Make sure that you aim the remote control at the projector's receivers within the angles listed here.
127
1 98.4 feet (30 m)
2 50°
3 40°
4 30°
Note: Avoid using the remote control in conditions with bright fluorescent lights or in direct sunlight, or
the projector may not respond to commands. If you will not use the remote control for a long time,
remove the batteries.
Parent topic: Using Basic Projector Features
Related tasks
Replacing the Remote Control Batteries
Projection Modes
Depending on how you positioned the projector, you may need to change the projection mode so your
images project correctly.
•Front (default setting) lets you project from a table in front of the screen.
•Front/Ceiling flips the image over top-to-bottom to project upside-down from a ceiling or wall mount.
•Rear flips the image horizontally to project from behind a translucent screen.
•Rear/Ceiling flips the image over top-to-bottom and horizontally to project from the ceiling and behind
a translucent screen.
Changing the Projection Mode Using the Remote Control
Changing the Projection Mode Using the Menus
Parent topic: Using Basic Projector Features
Changing the Projection Mode Using the Remote Control
You can change the projection mode to flip the image over top-to-bottom.
1. Turn on the projector and display an image.
128
2. Hold down the Shutter button on the remote control for 5 to 10 seconds.
The image disappears briefly and reappears flipped top-to-bottom.
3. To change projection back to the original mode, hold down the Shutter button for 5 to 10 seconds
again.
Parent topic: Projection Modes
Changing the Projection Mode Using the Menus
You can change the projection mode to flip the image over top-to-bottom and/or left-to-right using the
projector menus.
1. Turn on the projector and display an image.
2. Press the Menu button.
3. Select the Extended menu and press Enter.
4. Select the Projection setting and press Enter.
129
5. Select a projection mode and press Enter.
6. Press Menu or Esc to exit the menus.
Parent topic: Projection Modes
Image Aspect Ratio
The projector can display images in different width-to-height ratios called aspect ratios. Normally the
input signal from your video source determines the image's aspect ratio. However, for certain images
you can change the aspect ratio to fit your screen by pressing a button on the remote control.
If you always want to use a particular aspect ratio for a certain video input source, you can select it using
the projector's menus.
Changing the Image Aspect Ratio
Available Image Aspect Ratios
Parent topic: Using Basic Projector Features
Related references
Input Signal Settings - Signal Menu
Changing the Image Aspect Ratio
You can change the aspect ratio of the displayed image to resize it.
Note: Set the Screen Type setting in the projector's Extended menu before changing the aspect ratio.
1. Turn on the projector and switch to the image source you want to use.
2. Press the Aspect button on the remote control.
The shape and size of the displayed image changes, and the name of the aspect ratio appears
briefly on the screen.
130
3. To cycle through the available aspect ratios for your input signal, press the Aspect button
repeatedly.
Note: If you are projecting from a computer and parts of the image are cut off, set the Resolution
setting to Wide or Normal in the Signal menu.
Parent topic: Image Aspect Ratio
Related references
Available Image Aspect Ratios
Input Signal Settings - Signal Menu
Related tasks
Setting the Screen Type
Available Image Aspect Ratios
You can select the following image aspect ratios, depending on the selected Screen Type setting and
the input signal from your image source.
Note: Black bands and cropped or stretched images may project in certain aspect ratios, depending on
the aspect ratio and resolution of your input signal.
Aspect ratio setting Description
Auto Automatically sets the aspect ratio according to the input signal.
Normal Displays images in the same aspect ratio of the input signal.
4:3 Displays images at a 4:3 aspect ratio.
16:9 Displays images at a 16:9 aspect ratio.
Full Displays images using the full size of the projection area, but does
not maintain the aspect ratio.
H-Zoom
V-Zoom
Displays images using the full width (H-Zoom) or full height (V-
Zoom) of the projection area and maintains the aspect ratio of the
image. Areas that exceed the edges of the projected screen are not
projected.
Native Displays images as is (aspect ratio and resolution are maintained).
Areas that exceed the edges of the projected screen are not
projected.
131
Parent topic: Image Aspect Ratio
Related tasks
Setting the Screen Type
Color Mode
The projector offers different Color Modes to provide optimum brightness, contrast, and color for a
variety of viewing environments and image types. You can select a mode designed to match your image
and environment, or experiment with the available modes.
If you always want to use a particular color mode for a certain video input source, you can select it using
the projector menus.
Changing the Color Mode
Available Color Modes
Parent topic: Using Basic Projector Features
Related references
Image Quality Settings - Image Menu
Changing the Color Mode
You can change the projector's Color Mode using the remote control to optimize the image for your
viewing environment.
1. Turn on the projector and switch to the image source you want to use.
2. If you are projecting from a DVD player or other video source, insert a disc or other video media and
press the play button, if necessary.
3. Press the Color Mode button on the remote control to change the Color Mode.
The image appearance changes and the name of the Color Mode appears briefly on the screen.
132
4. To cycle through all the available Color Modes for your input signal, press the Color Mode button
repeatedly.
Parent topic: Color Mode
Related references
Available Color Modes
Available Color Modes
You can set the projector to use these Color Modes, depending on the input source you are using:
Color Mode Description
Dynamic Best for projecting in a bright room
Presentation Best for color presentations in a bright room
Natural Best for projecting still pictures such as photos
Cinema Best for movies projected in a dark room
BT.709 Best for watching digital TV or Blu-ray discs; produces images that
conform to the ITU-R BT.709 standard
DICOM SIM* Best for projecting X-ray photographs and other medical images
Multi-Projection Best for projecting from multiple projectors (reduces the color tone
difference between images)
* Available only when inputting RGB signals
Note: The DICOM SIM Color Mode is for reference purposes only and should not be used to make
medical diagnoses.
Parent topic: Color Mode
Adjusting the Brightness
You can adjust the brightness of your projector's light source.
1. Turn on the projector and switch to the image source you want to use.
2. Press the Menu button.
133
3. Select the Settings menu and press Enter.
4. Select the Brightness Settings setting and press Enter.
5. Select the Light Source Mode setting and press Enter.
6. Select one of the following options:
•Normal: Sets brightness to the maximum level (ideal for conference rooms, auditoriums, and
lecture halls)
•Quiet: Sets brightness to 70% and reduces fan noise (ideal for libraries, theaters, museums, and
art galleries)
•Extended: Sets brightness to 70% and extends the life expectancy of the light source (ideal for
darker environments with ambient light, such as museums and art galleries, where a reduced
maintenance cycle is desired)
•Custom: Allows you to select a custom brightness level between 30 to 100%
7. If you selected Custom, select Brightness Level from the Brightness Settings screen and use the
left and right arrow buttons to select the brightness.
8. If you selected Custom and want to maintain consistent brightness, turn on the Constant
Brightness setting.
Note: If you turn on Constant Brightness, you cannot change the Light Source Mode and
Brightness Level settings. If you turn off Constant Brightness, the Brightness Level setting
changes according to the status of the light source.
134
9. Press Menu or Esc to exit the menus.
Note: If you use the projector continuously for more than 24 hours, or regularly turn it off by shutting off
the power outlet, schedule periodic Light Source Calibration events from the Extended menu.
Otherwise, the Constant Brightness setting may not work properly.
Constant Brightness Usage Hours
Parent topic: Using Basic Projector Features
Related references
Projector Setup Settings - Extended Menu
Related tasks
Saving a Scheduled Event
Constant Brightness Usage Hours
If you turn on the Constant Brightness setting, the number of hours the projector can maintain constant
brightness is displayed as the Estimated Remains setting.
Display level Estimated remaining hours
10000 or more hours
135
Display level Estimated remaining hours
8000 to 9999 hours
6000 to 7999 hours
4000 to 5999 hours
2000 to 3999 hours
0 to 1999 hours
Light source life span
The estimated life span of the light source varies depending on the Brightness Level setting and
whether the Constant Brightness setting is on or off.
Constant Brightness off
Brightness Level setting Hours
100% 20000 hours
90% 36000 hours
80% 41000 hours
70% 43000 hours
60% 46000 hours
50% 57000 hours
40% 75000 hours
30% 103000 hours
Constant Brightness on
1 Brightness level
136
2 Time the projector can maintain constant brightness (approximate)
Brightness Level setting Hours
85% 7000 hours
80% 15000 hours
70% 25000 hours
60% 35000 hours
50% 47000 hours
40% 66000 hours
30% 95000 hours
Note: The light source usage hours vary depending upon environmental conditions and usage. The
hours listed here are an approximate and are not guaranteed. You may need to replace parts in the
projector sooner than the estimated light source operation time. If Constant Brightness is turned on,
and you have exceeded the usage hours listed here, you may not be able to select a high Brightness
Level setting.
Parent topic: Adjusting the Brightness
Adjusting Luminance Controls
You can turn on the Dynamic Contrast setting to automatically optimize the image luminance. This
improves the image contrast based on the brightness of the content you project. You can also set the
light source to turn off automatically after a certain time period while projecting at a specific brightness
level.
1. Turn on the projector and switch to the image source you want to use.
2. Press the Menu button.
137
3. Select the Image menu and press Enter.
4. Select the Light Source Control setting and press Enter.
You see this screen:
5. Select the Light Source Control setting, choose one of the following options, and press Enter:
•Off: Turns off light source control.
•Dynamic Contrast: Automatically adjusts the amount of light according to the brightness of the
image.
138
•Lights-Out Control: Automatically turns off the light after a certain time has elapsed while
projecting at the specified video level.
6. Press the Esc button.
7. If you selected Dynamic Contrast as the Light Source Control setting, select the Dynamic
Contrast setting, choose one of the following options, and press Enter:
• Select the Response Speed setting and select either Normal (to adjust brightness at the
standard speed) or High Speed (to adjust brightness as soon as the scene changes).
• Select the Black Level setting and select the black level you want to project when the brightness
level of the image signal is zero. (If you select 0%, the light source turns off.)
8. If you selected Lights-Out Control as the Light Source Control setting, select the Lights-Out
Control setting, choose one of the following options, and press Enter:
• Select the Light-Out Signal Level setting and select the brightness level for the current video
signal. If the brightness level exceeds this level, the light source turns off automatically and then
turns back on immediately.
• Select the Lights-Out Timer setting and select the amount of time before the light source
automatically turns off.
9. Press Menu to exit the menus.
Parent topic: Using Basic Projector Features
Adjusting Gamma
You can adjust the gamma to improve differences in halftone brightness that vary depending on the
connected device.
Note: Project a still image to adjust the gamma; you cannot adjust it properly when projecting a movie or
other moving video. Medical images many not reproduce correctly depending on your operating
environment and screen.
1. Turn on the projector and switch to the image source you want to use.
2. Press the Menu button.
3. Select the Image menu and press Enter.
4. Select Advanced, select the Gamma setting, and press Enter.
139
You see a screen like this:
5. Use the arrow buttons to adjust the value of the Gamma setting as follows:
• To brighten darker areas of the image, select higher gamma values. (Color saturation in the lighter
areas may become weaker.)
• To reduce overall image brightness and sharpen the image, select lower gamma values.
• If you are projecting using DICOM SIM as the Color Mode setting, adjust the gamma according to
the projection width. If it is less than 150 inches (3.81 m) wide, select a smaller value; if it is wider,
select a larger value.
6. To adjust specific tones in the gamma using a graph, select the Custom setting and press Enter.
You see a screen like this:
140
7. Press the left or right arrow button to select the tone you want to change, then press the up or down
arrow button to adjust the tone and press Enter.
8. Press Menu to exit the menus.
Parent topic: Using Basic Projector Features
Setting the Date and Time
You can set the date and time for the projector.
Note: If the Schedule Protection setting in the Password Protection screen is enabled, you cannot
change the date and time settings.
1. Press the Menu button.
2. Select the Extended menu and press Enter.
3. Select the Operation setting and press Enter.
4. Select the Date & Time setting and press Enter.
You see a screen like this:
5. Select your date and time settings. Then select Set and press Enter to confirm your changes.
6. When you are finished, press the Menu button to exit.
Date and Time Settings
Parent topic: Using Basic Projector Features
Related concepts
Password Security Types
141
Date and Time Settings
Settings Options Description
Date & Time Date
Time
Time Difference (UTC)
Adjusts the projector's date and time
settings
Date and Time: sets the date and time
Time Difference (UTC): sets the time
difference from Coordinated Universal
Time
Daylight Saving Time Daylight Saving Time
DST Start
DST End
DST Adjustment (min)
Adjusts the daylight saving time
settings
Daylight Saving Time: enables or
disables daylight saving time
DST Start and DST End: sets the date
and time to start or end daylight saving
time
DST Adjustment (min): sets the
difference between standard and
daylight saving time
Internet Time Internet Time
Internet Time Server
Automatically adjusts the time through
an Internet connection
Internet Time: turn on this setting to
update the date and time automatically
through an Internet time server
Internet Time Server: sets the IP
address for the Internet time server
Parent topic: Setting the Date and Time
142
Adjusting Projector Features
Follow the instructions in these sections to use your projector's feature adjustments.
Shutting Off the Picture Temporarily
Stopping Video Action Temporarily
Projector Security Features
Projecting Two Images Simultaneously
Using Advanced Image Adjustment Features
Using Multiple Projectors
Enabling Protocol Emulation
Saving Settings to Memory and Using Saved Settings
Saving a Scheduled Event
Copying Menu Settings Between Projectors
Shutting Off the Picture Temporarily
You can temporarily turn off the projected picture if you want to redirect your audience's attention during
a presentation. Any video action continues to run, however, so you cannot resume projection at the point
that you stopped it.
Note: If the picture is off for more than 2 hours, the power automatically turns off. You can disable the
Shutter Timer setting in the Extended Menu to turn off this feature.
143
1. Press the Shutter button on the projector's control panel or remote control to temporarily stop
projection.
2. To turn the picture back on, press the Shutter button again.
Note: To fade the image in and out when you press the Shutter button, turn on the Fade-out and Fade-
in settings in the Extended menu. If you selected Shutter as the Shutter Release setting in the
Extended menu, you can still control the projector while the shutter feature is active.
Parent topic: Adjusting Projector Features
Related references
Projector Setup Settings - Extended Menu
Stopping Video Action Temporarily
You can temporarily stop the action in a video or computer presentation and keep the current image on
the screen. Any video action continues to run, however, so you cannot resume projection at the point
that you stopped it.
144
1. Press the Freeze button on the remote control to stop the video action.
2. To restart the video action in progress, press Freeze again.
Parent topic: Adjusting Projector Features
Projector Security Features
You can secure your projector to deter theft or prevent unintended use by setting up the following
security features:
• Password security to prevent the projector from being turned on, and prevent changes to the startup
screen and other settings.
• Button lock security to block operation of the projector using the buttons on the control panel or remote
control.
• Security cabling to physically cable the projector in place.
Password Security Types
Locking the Projector's Lens Settings and Buttons
Locking the Remote Control Buttons
Installing a Security Cable
Parent topic: Adjusting Projector Features
Password Security Types
You can set up these types of password security using one shared password:
•Power On Protection password prevents anyone from using the projector without first entering a
password.
•User's Logo Protection password prevents anyone from changing the custom screen the projector
can display when it turns on. The presence of the custom screen discourages theft by identifying the
projector’s owner.
145
•Network Protection password prevents anyone from changing the network settings in the projector
menus.
•Schedule Protection password prevents anyone from changing the projector's time or schedule
settings.
•Remote Camera Access password prevents anyone from changing the projector's Remote Camera
Access settings in the Network menu.
Note: Additional security measures are available for the Remote Camera Access feature. Contact
Epson for details.
Setting a Password
Selecting Password Security Types
Entering a Password to Use the Projector
Saving a User's Logo Image to Display
Parent topic: Projector Security Features
Setting a Password
To use password security, you must set a password.
Note: The default password is set to 0000.
1. Hold down the Freeze button on the remote control for about five seconds or until you see this
menu.
2. Press the down arrow to select Password and press Enter.
You see the prompt "Change the password?".
146
3. Select Yes and press Enter.
4. Press and hold down the Num button on the remote control and use the numeric buttons to set a
four-digit password.
The password displays as **** as you enter it. Then you see the confirmation prompt.
5. Enter the password again.
You see the message "Password accepted."
6. Press Esc to return to the menu.
7. Make a note of the password and keep it in a safe place in case you forget it.
Parent topic: Password Security Types
Selecting Password Security Types
After setting a password, you see this menu, allowing you to select the password security types you want
to use.
147
If you do not see this menu, hold down the Freeze button on the remote control for about five seconds or
until the menu appears.
• To prevent unauthorized use of the projector, select Power On Protection, press Enter, select On,
press Enter again, and press Esc.
• To prevent changes to the User's Logo screen or related display settings, select User's Logo
Protection, press Enter, select On, press Enter again, and press Esc.
• To prevent changes to network settings, select Network Protection, press Enter, select On, press
Enter again, and press Esc.
• To prevent changes to the projector's time or schedule settings, select Schedule Protection, press
Enter, select On, press Enter again, and press Esc.
• To prevent changes to the projector's Remote Camera Access settings in the Network menu, select
Remote Camera Access, press Enter, select On, press Enter again, and press Esc.
Note: Be sure to keep the remote control in a safe place; if you lose it, you will not be able to enter the
password required to use the projector.
Parent topic: Password Security Types
Entering a Password to Use the Projector
If a password is set up and a Power On Protection password is enabled, you see a prompt to enter a
password whenever you turn on the projector.
You must enter the correct password to use the projector.
148
1. Press and hold down the Num button on the remote control while you enter the password using the
numeric buttons.
Note: The default password is 0000.
The password screen closes.
2. If the password is incorrect, the following may happen:
• You see a "wrong password" message and a prompt to try again. Enter the correct password to
proceed.
• If you have forgotten the password, make note of the Request Code: xxxxx number that appears
on the screen and contact Epson Support.
• If you enter an incorrect password three times in succession, you see a message telling you that
the projector is locked. After the message is displayed for 5 minutes, the projector enters standby
mode. Unplug the projector, plug in the power cord, and turn on the projector. You see a prompt to
enter the password.
• If you continue to enter an incorrect password many times in succession, the projector displays a
request code and a message to contact Epson Support. Do not attempt to enter the password
again. When you contact Epson Support, provide the displayed request code and proof of
ownership for assistance in unlocking the projector.
Parent topic: Password Security Types
Related references
Where to Get Help
Saving a User's Logo Image to Display
You can transfer an image to the projector and then display it whenever the projector turns on. You can
also display the image when the projector is not receiving an input signal or when you temporarily stop
projection (using the Shutter feature). This transferred image is called the User's Logo screen.
149
The image you select as the User's Logo can be a photo, graphic, or company logo, which is useful in
identifying the projector's owner to help deter theft. You can prevent changes to the User's Logo by
setting up password protection for it.
Note: When you copy the menu settings from one projector to another using the batch setup feature, the
user logo is also copied. Do not include any information in the user logo that you do not want to share
between multiple projectors.
1. Display the image you want to project as the User's Logo.
2. Press the Menu button, select the Extended menu, and press Enter.
3. Select the User's Logo setting and press Enter.
4. Select Start Setting and press Enter.
You see a prompt asking if you want to use the displayed image as a user's logo.
5. Select Yes and press Enter.
6. Select the capture size and press Enter.
7. Use the arrow buttons on the remote control or control panel to surround the image area you want to
use as the User's Logo and press Enter.
You see a prompt asking if you want to select this image area.
8. Select Yes and press Enter. (If you want to change the selected area, select No, press Enter, and
repeat the last step.)
You see the User's Logo zoom factor menu.
150
9. Select a zoom percentage and press Enter.
You see a prompt asking if you want to save the image as the User's Logo.
10. Select Yes and press Enter.
You see a completion message.
11. Press Esc to exit the message screen.
12. Select the Extended menu and press Enter.
13. Select Display and press Enter.
14. Select when you want to display the User's Logo screen:
• To display it whenever there is no input signal, select Display Background and set it to Logo.
• To display it whenever you turn the projector on, select Startup Screen and set it to On.
To prevent anyone from changing the User's Logo settings without first entering a password, set a
password and enable User's Logo security.
Parent topic: Password Security Types
Related tasks
Saving Settings to Memory and Using Saved Settings
Locking the Projector's Lens Settings and Buttons
You can lock the buttons on the projector's control panel to prevent anyone from using the projector. You
can also lock the zoom, focus, and lens shift settings to prevent them from being adjusted.
Note: You can use the remote control to control the projector when the control panel buttons are locked.
1. Press the Menu button.
151
2. Select the Settings menu and press Enter.
3. Select the Lock Setting setting and press Enter.
Note: You can also press the lock button on the control panel to display the Control Panel Lock
screen.
4. Select one of these lock types and press Enter:
• To lock the zoom, focus, and lens shift settings, select Lens Lock.
• To lock all buttons, select Control Panel Lock >Full Lock.
• To lock all buttons except the power button, select Control Panel Lock >Partial Lock.
Note: A message is displayed on the screen if any control panel buttons are pressed while this
setting is enabled.
You see a confirmation prompt.
5. Select Yes and press Enter.
6. Restart the projector for the lock settings to take effect.
Unlocking the Projector's Buttons
Parent topic: Projector Security Features
152
Related tasks
Locking the Remote Control Buttons
Unlocking the Projector's Buttons
If the projector's control panel buttons have been locked, hold the Enter or lock button on the
projector's control panel for seven seconds to unlock them. You can also use the remote control to set
the Control Panel Lock setting to Off in the Settings menu.
If the remote control buttons have been locked, hold the ibutton on the remote control for 5 seconds to
unlock them.
Parent topic: Locking the Projector's Lens Settings and Buttons
Related references
Projector Feature Settings - Settings Menu
Projector Parts - Remote Control
Related tasks
Locking the Remote Control Buttons
Locking the Remote Control Buttons
You can lock some of the buttons on the remote control.
To lock the remote control buttons related to lens operation, turn on the Lens Lock setting in the
Settings menu.
153
To lock the remote control buttons shown here, press and hold the ibutton on the remote control for
approximately 5 seconds. (To unlock the buttons, press and hold the ibutton again for approximately 5
seconds.)
Note: If you lock the remote control buttons, you can still reset the Remote Receiver setting in the
Settings menu to the default settings.
Parent topic: Projector Security Features
Related references
Projector Feature Settings - Settings Menu
Related tasks
Locking the Projector's Lens Settings and Buttons
154
Installing a Security Cable
You can install two types of security cables on the projector to deter theft.
• Use the security slot on the projector to attach a Kensington lock. See your local computer or
electronics dealer for purchase information.
• Use both of the drop-prevention wire attachment points to connect a wire to the projector that supports
a weight of at least 220.5 lb (100 kg). Secure the wire to the wall, ceiling, or projector mount without
leaving any slack in the wire. Check any installation instructions included with the wire.
Parent topic: Projector Security Features
Related references
Projector Parts - Side/Rear
Projector Parts - Base
Projecting Two Images Simultaneously
You can use the split screen feature to simultaneously project two images from different image sources
next to each other. You can control the split screen feature using the projector menus.
Note: While you use the split screen feature, other projector features may not be available and some
settings may be automatically applied to both images. You cannot project from the same input source
onto both sides (left and right) of the screen. You also cannot use split screen with certain input source
combinations.
155
1. Press the Menu button.
2. Select the Settings menu and press Enter.
3. Select Split Screen and press Enter.
4. Press the Menu button.
You see this screen:
5. To select an input source for the other image, select the Source setting, press Enter, select the
input source, select Execute, and press Enter. (You can also change image sources, if necessary.)
6. To switch the images, select the Swap Screens setting and press Enter.
156
7. To change the image sizes, select the Screen Size setting, press Enter, select a sizing option,
press Enter, and press Menu to exit.
Note: Depending on the video input signals, the images may not appear at the same size even if you
choose the Equal setting.
8. To exit the split screen feature, select Exit Split Screen or press the Esc button.
Input Sources for Split Screen Projection
Parent topic: Adjusting Projector Features
Input Sources for Split Screen Projection
You can choose from the input source combinations listed here for split screen projection.
Note: If you installed the optional DisplayPort interface board, you also cannot choose the port 1 and
port 2 input sources for split screen projection.
Left Screen Right Screen
HDMI HDBaseT DVI-D SDI Computer BNC LAN
HDMI — —
HDBaseT —
DVI-D — —
SDI — — — —
Computer — — — —
BNC — — — —
LAN — — — —
Parent topic: Projecting Two Images Simultaneously
Related references
Projector Parts - Interface Ports
Using Advanced Image Adjustment Features
Follow the instructions in these sections to use your projector's advanced image adjustments.
157
Using Frame Interpolation
Creating Image Presets
Using MPEG Noise Reduction
Adjusting Scaled Resolution Images (Super-resolution)
Adjusting Detail Enhancement
Adjusting the Color Convergence (Panel Alignment)
Adjusting the Color Tone (Color Uniformity)
Running Light Source Calibration
Parent topic: Adjusting Projector Features
Using Frame Interpolation
You can use the projector's Frame Interpolation feature to smooth fast-moving video by comparing
consecutive image frames and inserting an intermediate image frame between them.
You cannot use this feature in any of the following conditions:
• The input signal exceeds 1920 in horizontal resolution
• You selected V-Zoom as the Aspect setting
• You turned on the Edge Blending or Scale settings
1. Press the Menu button.
158
You see a screen like this:
2. Select the Image Enhancement setting and press Enter.
3. Select the Frame Interpolation setting and press Enter.
You see a screen like this:
4. Select the level of interpolation and press Enter.
5. When you are finished, press the Menu button.
Note: If your resulting images contain noise, turn off the Frame Interpolation setting.
Parent topic: Using Advanced Image Adjustment Features
159
Creating Image Presets
You can quickly optimize your projected image by selecting image adjustment settings and saving them
as a preset you can reuse later.
You can save the following settings in a preset:
• Frame Interpolation
• Deinterlacing
• Noise Reduction
• MPEG Noise Reduction
• Super-resolution
• Detail Enhancement
1. Press the Menu button.
You see a screen like this:
2. Select the Image Enhancement setting and press Enter.
160
3. Select the Image Preset Mode setting and press Enter.
4. Select one of the presets and press Enter.
Note: If you select a previously used preset, your new adjustments overwrite the old ones.
5. Press Esc to return to the Image Enhancement menu.
6. Fine-tune the following settings:
• Frame Interpolation
• Deinterlacing
• Noise Reduction
• MPEG Noise Reduction
• Super-resolution
• Detail Enhancement
7. Press Menu or Esc to exit the menus.
The currently selected Image Preset Mode will be updated with the current settings.
Parent topic: Using Advanced Image Adjustment Features
Using MPEG Noise Reduction
If you are projecting MPEG movies, you can reduce dots and block noise by adjusting the MPEG Noise
Reduction setting.
You cannot use this feature if the input signal exceeds 1920 horizontal resolution.
1. Press the Menu button.
161
You see a screen like this:
2. Select the Image Enhancement setting and press Enter.
3. Select the MPEG Noise Reduction setting and press Enter.
4. Select the level of noise reduction and press Enter.
5. Press Menu or Esc to exit the menus.
Parent topic: Using Advanced Image Adjustment Features
Adjusting Scaled Resolution Images (Super-resolution)
You can sharpen blurry, low-resolution images that had their resolution scaled up for projection using the
Super-resolution setting.
1. Turn on the projector and switch to the image source you want to use.
2. Press the Menu button.
162
You see a screen like this:
3. Select the Image Enhancement setting and press Enter.
4. Select the Super-resolution setting and press Enter.
5. Adjust each of the following options as necessary:
•Fine Line Adjust to enhance fine details such as hair and fabric patterns
•Soft Focus Detail to enhance the outline, background, and main parts of an image
Note: Higher values increase the intensity of the effect.
6. Press Menu or Esc to exit the menus.
Parent topic: Using Advanced Image Adjustment Features
Adjusting Detail Enhancement
You can enhance the contrast in detailed areas of an image to create a more textured look.
1. Turn on the projector and switch to the image source you want to use.
163
2. Press the Menu button.
You see a screen like this:
3. Select the Image Enhancement setting and press Enter.
4. Select the Detail Enhancement setting and press Enter.
5. Adjust each of the following options as necessary:
•Strength to adjust the image contrast
•Range to adjust the enhanced area of the image
Note: Higher values increase the intensity of the effect. Depending on the image, you may notice a
highlight at the border between colors; if so, select lower values.
6. Press Menu or Esc to exit the menus.
Parent topic: Using Advanced Image Adjustment Features
Adjusting the Color Convergence (Panel Alignment)
You can use the Panel Alignment feature to manually adjust the color convergence (the alignment of the
red and blue colors) in the projected image.
Note: You can adjust only the red or blue color convergence. Green is the standard color panel and
cannot be adjusted.
164
1. Turn on the projector.
2. Press the Menu button.
3. Select the Extended menu and press Enter.
4. Select the Display setting and press Enter.
5. Select the Panel Alignment setting and press Enter.
6. Select the Panel Alignment setting again and press Enter.
7. Select On and press Enter.
8. Press Esc to return to the previous screen.
9. Select the Select Color setting and choose one of the following:
•Rto adjust the red color convergence.
•Bto adjust the blue color convergence.
10. Press Esc to return to the previous screen.
11. Select the Pattern Color setting and press Enter.
12. Select the pattern you want to use and press Enter.
13. Press Esc to return to the previous screen.
14. Select Start Adjustments and press Enter.
165
You see this screen:
15. First, select Shift the whole panel to adjust the entire panel and press Enter.
16. Use the arrow buttons on the remote control to adjust the whole panel and press Enter.
17. Next, select Adjust the four corners to make finer adjustments and press Enter.
18. Use the arrow buttons on the remote control to adjust the color alignment of the color you selected
for the Select Color setting and press Enter.
19. When you are finished adjusting each corner of the screen, press Enter.
20. Do one of the following:
• If your projector's panel alignment is now correct, select Exit and press Enter to return to the
Panel Alignment menu.
• If your projector needs additional panel alignment, select Select intersection and adjust and
press Enter to continue making adjustments.
Parent topic: Using Advanced Image Adjustment Features
Adjusting the Color Tone (Color Uniformity)
You can use the Color Uniformity feature to manually adjust the color tone balance in the projected
image.
1. Press the Menu button.
166
2. Select the Extended menu and press Enter.
3. Select the Display setting and press Enter.
4. Select the Color Uniformity setting and press Enter.
You see this screen:
5. Press Enter and select On.
6. Press Esc.
167
7. Select the Adjustment Level setting and press Enter.
8. Press the right and left arrow buttons to adjust the level, and press Esc.
9. Select the Start Adjustments setting and press Enter.
10. Select the area of the screen that you want to adjust and press Enter.
Note: Adjust the outer areas first, then adjust the entire screen.
11. Select the color (Red,Green, or Blue) you want to adjust, and use the left arrow button to weaken
the color tone and the right arrow button to strengthen the color tone.
12. Press Esc.
13. Repeat steps 10 and 11 for each area you want to adjust.
14. Repeat steps 7 to 11 for each adjustment level.
15. When you are finished, press the Menu button.
Parent topic: Using Advanced Image Adjustment Features
Running Light Source Calibration
Light source calibration automatically adjusts any difference between the white balance and the
brightness level of the light source. You should perform light source calibration every 100 hours of
projector usage. You can also schedule automatic calibration or run the light source calibration manually
using the menus.
168
Automatic light source calibration may not start in the following conditions:
• Within 30 minutes of turning on the projector.
• When using the Shutter feature or within 30 minutes of releasing the shutter.
• When using direct power shutdown.
• When you have used the projector continuously for over 24 hours.
Note: To perform a light source calibration, the projector must have been on for at least 30 minutes and
the projector brightness must not be automatically dimmed due to high temperatures.
1. Press the Menu button.
2. Select the Reset menu and press Enter.
You see a screen like this:
3. Select Light Source Calibration and press Enter.
4. Select any of the following:
• To run the light source calibration now, select Run Now.
• To automatically run the light source calibration every 100 hours of projector usage, select Run
Periodically.
• To schedule automatic calibration, select Schedule Settings.
169
•Last Run displays the last time the projector performed a calibration.
Note: If you use the projector continuously for more than 24 hours or use direct shutdown regularly,
select Schedule Settings to schedule calibration of the light source periodically.
5. When you are finished, select Return and press the Enter button to return to the Reset menu.
Parent topic: Using Advanced Image Adjustment Features
Related tasks
Turning On the Projector
Turning Off the Projector
Stopping Video Action Temporarily
Using Multiple Projectors
You can combine the projected images from two or more projectors to create one large image. Follow
the instructions in these sections to set up and project from multiple projectors.
Multiple Projector Adjustment Overview
Projector Identification System for Multiple Projector Control
Tiling Images into One Image
Blending the Image Edges
Adjusting the Black Level
Matching Tint and Brightness (Screen Matching)
Scaling an Image
Parent topic: Adjusting Projector Features
Multiple Projector Adjustment Overview
If you are combining images from multiple projectors on a network (up to 15), you can assign one
projector as the "master" and automatically adjust all the images to match the "master" image. If the
projectors are not connected to a network, you can match each projector's images manually.
Note: Make sure all networked projectors are connected using LAN cables, have their DHCP setting
turned on, and have been assigned an IP address. Also disable Sleep Mode on each projector so they
do not turn off during adjustment.
1. Turn on all the projectors.
170
2. To select a master projector for automatic adjustment, select Custom for the Light Source Mode
setting and set the Brightness Level setting to the maximum value for all projectors. The projector
with the darkest projected image is the master projector.
3. Do one of the following:
• For automatic adjustment, set an ID for the master projector and the remote control.
• For manual adjustment, set an ID for each projector and the remote control.
4. Adjust each projector's physical position and angle to the screen.
5. Do one of the following:
• For automatic adjustment, configure tiling automatically.
• For manual adjustment, configure tiling manually.
6. Adjust the image aspect ratio for each projector.
7. Adjust the position of the image for each projector using lens shift.
8. Adjust the zoom and focus for each projector.
9. Adjust small differences in the images using the Point Correction setting.
10. Adjust the edges of the images using the Edge Blending and Black Level settings.
11. Adjust the brightness and tint of the images using the Screen Matching setting.
12. Select sections of the images using the Scale setting.
Parent topic: Using Multiple Projectors
Related concepts
Wired Network Projection
Projector Identification System for Multiple Projector Control
Related references
Projector Feature Settings - Settings Menu
Related tasks
Changing the Image Aspect Ratio
Adjusting the Image Position Using Lens Shift
Resizing the Image with the Zoom Button
Focusing the Image Using the Focus and Distortion Buttons
Correcting Image Shape with Point Correction
Blending the Image Edges
171
Adjusting the Black Level
Scaling an Image
Related topics
Tiling Images into One Image
Matching Tint and Brightness (Screen Matching)
Projector Identification System for Multiple Projector Control
You can operate multiple projectors using one remote control for more elaborate presentations. To do
this, you assign an identification number to each projector and to the remote control. Then you can
operate all the projectors at once or individually.
Setting the Projector ID
Setting the Remote Control ID
Parent topic: Using Multiple Projectors
Setting the Projector ID
If you want to control multiple projectors from a remote control, give each projector a unique ID.
1. Press the Menu button.
2. Select the Extended menu and press Enter.
3. Select the Multi-Projection setting and press Enter.
4. Select Projector ID and press Enter.
5. Press the left or right arrow buttons on the remote control to select the identification number you
want to use for the projector. Then select Set and press Enter.
Repeat these steps for all the other projectors you want to operate from one remote control.
Note: To temporarily display the projector's ID number on the screen, hold down the ibutton and press
the ID button.
172
Parent topic: Projector Identification System for Multiple Projector Control
Setting the Remote Control ID
The remote control's ID is set to 0by default so it can operate any compatible projector. If you want to set
the remote control to operate only a particular projector, you need to set the remote control's ID to match
the projector's ID.
1. Turn on the projector you want the remote control to operate with exclusively.
2. Set the remote control ID switch to On.
3. Hold down the ID button on the remote control while you press the numeric button that matches the
projector's ID. (Enter a two-digit number, such as 01 for projector ID 1.) Then release the buttons.
Note: To temporarily display the projector's ID on the screen, press the ibutton and press the ID
button. If the batteries are left out of the remote control for an extended period, the remote control ID
returns to its default setting.
Parent topic: Projector Identification System for Multiple Projector Control
173
Related concepts
Image Shape
Related references
Additional Projector Software and Manuals
Tiling Images into One Image
You can project the same image from up to nine projectors to create one large image using the Tiling
feature.
Note: Before tiling, make sure the displayed images from your projectors are rectangular, correctly
sized, and focused.
Note: You can automatically adjust the tiling using the Tiling Assist feature in the Epson Projector
Professional Tool software available for download from the Epson website.
Configuring Tiling Automatically
Configuring Tiling Manually
Parent topic: Using Multiple Projectors
Configuring Tiling Automatically
If your projectors are on a network and you have identified a master projector, you can configure tiling
automatically.
174
1. Turn on the projector.
Note: Make sure nothing is blocking the built-in camera on the front of the projector.
2. Press the Menu button.
3. Select the Extended menu and press Enter.
4. Select Multi-Projection and press Enter.
You see this screen:
5. Select Projector Grouping and press Enter.
175
You see a screen like this:
6. Press the up or down arrow buttons to highlight a projector and press Enter to place a checkmark
next to each projector you want to use for tiling. Then select Set and press Enter.
7. Select Tiling and press Enter.
8. Select Tiling again and press Enter.
9. Select Auto and press Esc.
10. Select Location Setup and press Enter.
The projected images are positioned automatically.
11. When you see the message to assign projector IDs, select Yes.
176
When setup is complete, you see a screen like this:
Note: If any of the images are not positioned correctly, set up tiling manually instead.
12. Select the input signal to display an image.
After performing the steps here, adjust the images for any gaps and differences in color.
Note: Do not change any of the projector names or IP addresses, or the images will not be adjusted
automatically.
Parent topic: Tiling Images into One Image
Related tasks
Configuring Tiling Manually
Configuring Tiling Manually
If your projectors are not on a network or you were unsuccessful tiling the images automatically, you can
configure tiling manually.
1. Turn on the projector.
2. Press the Menu button.
3. Select the Extended menu and press Enter.
177
4. Select Multi-Projection >Tiling >Layout.
5. Select the number of rows and columns you are setting up as the Row and Column settings. Then
select Set and press Enter.
6. Repeat the previous steps with each projector you are setting up before continuing with the next
step.
7. Select Location Setup and press Enter.
8. Select the position of each projected image as follows:
•Row Order to layout the screens from top to bottom in sequential order, starting with 1at the top
178
•Column Order to layout the screens from left to right, starting with Aon the left
9. Repeat the previous step with each projector you are setting up before continuing with the next step.
10. Select the input signal to display an image.
After performing the steps here, adjust the images for any gaps and differences in color.
Parent topic: Tiling Images into One Image
Related tasks
Configuring Tiling Automatically
Blending the Image Edges
You can use the projector's Edge Blending feature to create a seamless image from multiple projectors.
Note: Before performing Edge Blending, set the Color Mode setting to Multi-Projection to make more
precise adjustments.
1. Press the Menu button.
2. Select the Extended menu and press Enter.
179
3. Select the Multi-Projection setting and press Enter.
4. Select the Edge Blending setting and press Enter.
You see this screen:
5. Turn on the Edge Blending,Line Guide, and Pattern Guide settings.
Note: If the projected guide is unclear, try changing the Guide Color setting.
6. Select the edge you want to blend on each projector and press Enter.
You see a screen like this:
7. Select the Blending setting and select On.
8. Press Esc to return to the previous screen.
9. Select the Blend Start Position setting and adjust the point where edge blending begins.
180
10. Select the Blend Range setting and use the arrow buttons to select the width of the blended area so
that the displayed guides are at the edges of the overlapping area between the two images.
11. Select the Blend Curve setting and select a gradient for the shaded area on the projectors.
12. Press Esc to go back to the previous screen.
13. When the edges are blended, turn off the Line Guide and Pattern Guide settings on each projector
to check the final settings.
14. When you are finished, press the Menu button.
Parent topic: Using Multiple Projectors
Related tasks
Changing the Color Mode
Adjusting the Black Level
When two images overlap, the overlapping area can appear differently from the areas that do not
overlap. You can use the projector's Black Level setting to make the difference less noticeable.
Note: You may not be able to adjust the black levels correctly if the Geometry Correction settings are
set too high. The brightness and tone of the overlapping areas may differ from the rest of the image even
after adjusting the black level.
1. Press the Menu button.
2. Select the Extended menu and press Enter.
181
3. Select the Multi-Projection setting and press Enter.
4. Select the Black Level setting and press Enter.
You see this screen:
5. Select the Color Adjustment setting and press Enter.
You see a screen based on the Top Edge,Bottom Edge,Right Edge, and Left Edge settings you
selected for the Edge Blending setting.
Note: The Color Adjustment setting is automatically adjusted when selecting Start Auto
Adjustment in the Screen Matching screen.
182
6. Select the area you want to adjust and press Enter.
Note: The area you selected is displayed in orange. Adjust overlapping areas starting with the
brightest areas first. For example, adjust area 2 to match area 1, then adjust area 3 to match area 2.
7. Adjust the brightness and tone of the areas that do not overlap to match the areas that overlap using
the displayed adjustment sliders.
8. Repeat the previous two steps as needed until all areas match.
9. If the tone of some areas do not match, you can adjust them using the Area Correction setting.
Continue with the next step. Otherwise, press the Menu button to exit.
10. Press the Esc button to return to the Black Level screen.
11. Select the Area Correction setting and press Enter.
12. Select the Start Adjustments setting and press Enter.
183
You see a screen with boundary lines indicating areas that are overlapping. The boundary lines are
based on the Top Edge,Bottom Edge,Right Edge, and Left Edge settings you selected for the
Edge Blending setting.
13. Use the arrow buttons to select a boundary line of the area you want to adjust and press Enter.
The selected line is displayed in orange.
14. Use the arrow buttons to adjust the boundary line position and press the Enter button.
15. Use the arrow buttons to select an adjustment point and press the Enter button.
The selected point turns orange.
184
16. Use the arrow buttons to move the point.
17. To move another point, press the Esc button and repeat the previous two steps.
18. To move another boundary line, press the Esc button repeatedly until you can select a boundary
line.
19. When you are finished, press the Esc button until you see a confirmation message. Select Yes and
press Enter to return to the Black Level screen.
20. When you are finished, press the Menu button.
Note: Changing the Top Edge,Bottom Edge,Right Edge, or Left Edge settings resets the Black
Level setting to its default value.
Parent topic: Using Multiple Projectors
Related references
Projector Feature Settings - Settings Menu
Related topics
Matching Tint and Brightness (Screen Matching)
Matching Tint and Brightness (Screen Matching)
You can adjust the tint and brightness of multiple projectors so they match better. You can also schedule
automatic adjustments to the tint and brightness.
Note: Wait 30 minutes after turning on the projector before using the Screen Matching feature and
darken the room for maximum accuracy. Brightness decreases over time, so you may need to perform
Screen Matching again to correct large differences in brightness.
185
Matching the Screens Automatically
Matching the Screens Manually
Parent topic: Using Multiple Projectors
Related tasks
Saving a Scheduled Event
Matching the Screens Automatically
You can automatically correct the brightness and tint for multiple projectors based on the brightness and
tint settings you selected for the master projector.
Before you start, make sure of the following:
• Select Multi-Projection for the Color Mode setting and adjust the Brightness,Contrast,Color
Saturation,Tint,White Balance, and Advanced settings in the Image menu, as necessary, on the
master projector.
• You are projecting on a matte white diffusion screen that is flat and even.
• The projected image is between 100 to 300 inches (254 to 762 cm) and is rectangular after tiling.
• All the projectors are connected to a network and the Location Setup setting has been configured.
• Nothing is blocking the built-in camera on the front of each projector.
• The projected images do not overlap or have gaps between them.
• The projectors are installed parallel to the screen.
• The Blend Range setting is set between 15 to 45%.
• All the projectors are the same model.
Note: Auto adjustment is not available for the following lenses: ELPLX02, ELPLX02W, ELPLU04, or
ELPLL08. After auto adjustment, the movement range for lens shift is reduced.
1. Press the Menu button.
2. Select the Extended menu and press Enter.
3. Select the Multi-Projection setting and press Enter.
186
4. Select the Screen Matching setting and press Enter.
5. Select Start Auto Adjustment press Enter.
Select Yes when a message appears. When adjustment starts, you see an adjustment pattern.
Adjustment is complete when you see a displayed image.
After automatic adjustment, the Color Uniformity and Color Matching settings are returned to their
default values, and the Light Source Control setting is turned off. You may have to adjust the Blend
Curve setting manually if it was not set correctly during automatic adjustment.
Parent topic: Matching Tint and Brightness (Screen Matching)
Related references
Image Quality Settings - Image Menu
Projector Parts - Front/Top
Related tasks
Changing the Color Mode
Configuring Tiling Automatically
Blending the Image Edges
Matching the Screens Manually
You can manually correct the brightness and tint for multiple projectors.
1. Press the Menu button.
2. Select the Extended menu and press Enter.
187
3. Select the Multi-Projection setting and press Enter.
4. Select the Screen Matching setting and press Enter.
5. Select the Color Matching setting and press Enter.
You see this screen:
6. Press the left or right arrow buttons to select a value for the Adjustment Level setting.
Note: There are eight adjustment levels ranging from white to black and you can adjust each level
individually.
7. Press the left or right arrow buttons to adjust the color tone for the Red,Green, and Blue settings.
8. Press the left or right arrow buttons to adjust the Brightness setting.
9. Repeat the previous three steps as necessary to adjust each adjustment level.
10. Press the Esc button to return to the previous screen.
Parent topic: Matching Tint and Brightness (Screen Matching)
188
Scaling an Image
You can project the same image from multiple projectors and use the Scale feature to crop and combine
them into one large image.
1. Press the Menu button.
2. Select the Extended menu and press Enter.
3. Select the Multi-Projection setting and press Enter.
4. Select the Scale setting and press Enter.
You see this screen:
5. Select one of the following as the Scale setting:
•Auto to automatically adjust the clipped areas according to the Edge Blending and Tiling
settings you selected
•Manual to adjust the clipped areas manually
6. Select the Scale Mode setting and select one of these options:
•Zoom Display to maintain the image aspect ratio as you scale the image
189
•Full Display to adjust the image to the projector's screen size as you scale the image
7. If you selected Auto as the Scale setting, you can skip the remaining steps. If you selected Manual,
adjust each of the following options as necessary:
• Select –or +to scale the image horizontally and vertically at the same time
Note: You can set a value between 0.5 and 10.
• Select Scale Vertically to scale the image vertically only
• Select Scale Horizontally to scale the image horizontally only
8. Select the Clip Adjustment setting and use the arrow buttons to adjust the coordinates and size of
each image as you view the screen.
9. Select the Clip Range setting to preview the area you just selected.
10. Press the Menu button to exit.
Parent topic: Using Multiple Projectors
Related tasks
Blending the Image Edges
Related topics
Tiling Images into One Image
Enabling Protocol Emulation
You can use protocol emulation to control your projector with the same RS-232 control codes as those
used by the manufacturers of other projectors. This lets you control a group of projectors from a common
controller.
1. Make sure the projector is turned on.
2. Connect a controller to the RS-232C port on the projector.
3. Do one of the following:
• Press and hold the Test Pattern button on the remote control for at least five seconds.
• Select the Extended menu, highlight the Standby Mode setting, and hold down the right arrow
button on the remote control or projector control panel for at least five seconds.
You see the Protocol Emulation screen.
190
4. Select one of the following and press Enter:
•Type P for Panasonic projectors
•Type M for Mitsubishi projectors
•Type N for NEC projectors
•Type S for Sony projectors
•Type SA for Sanyo projectors
5. Turn the projector off and on again to enable the protocol emulation you selected.
Parent topic: Adjusting Projector Features
Related references
Projector Parts - Interface Ports
Projector Setup Settings - Extended Menu
Saving Settings to Memory and Using Saved Settings
You can save customized settings and then select the saved settings whenever you want to use them.
1. Turn on the projector and display an image.
2. Press the Menu button.
3. Select the Settings menu and press Enter.
191
4. Select the Memory setting and press Enter.
Note: You can also access this screen by pressing the Memory button on the remote control.
5. Select one of the following options:
•Memory: Saves or loads various settings; you can save up to 10 different memories
Note: The following settings are saved: all settings from the Image menu, the Scale,Overscan,
and Video Range settings from the Signal menu, and the Edge Blending,Black Level, and
Color Matching settings from the Extended menu.
•Lens Position: Saves or loads settings related to the lens such as the lens shift, focus, zoom, and
distortion adjustment settings; you can save up to 10 different memories
•Geometry Correction: Saves or loads any adjustments made in the Geometry Correction
setting in the Settings menu; you can save up to 3 different memories
192
You see this screen:
6. Select one of the following options:
•Load Memory: Overwrites your current settings with saved settings
•Save Memory: Saves your current settings to memory
Note: A memory name that has already been used is indicated by a blue mark. Saving over a
previously saved memory overwrites the settings with your current settings.
•Erase Memory: Erases the selected memory settings
•Rename Memory: Renames a saved memory
•Reset Memory: Resets the name and settings of a saved memory
Note: To reset all saved memories of all types, select Reset All Memories in the Reset menu.
7. Press Menu or Esc to exit.
Parent topic: Adjusting Projector Features
Saving a Scheduled Event
You can select projector commands you want to perform and schedule them as an event.
193
You cannot schedule an event to occur at the following times:
• Five minutes before or after a Color Calibration event
• Five minutes before or 30 minutes after a Screen Matching event
Note: Make sure to perform Screen Matching after executing Light Source Calibration.
Note: When you have set Light Source Calibration or Screen Matching events and you want to apply this
schedule to other projectors with tiling settings, set Sync Schedule to On.
1. Press the Menu button.
2. Select the Extended menu and press Enter.
3. Select the Schedule Settings setting and press Enter.
You see a screen like this:
4. Select the Schedule or Extended Schedule menu and press Enter.
5. Select Add New and press Enter.
6. In the Event Settings section, select the events you want to have occur. (Select No Change or Off
for events that you do not want to occur.)
Note: In the Extended Schedule menu, you can schedule only one event for Color Calibration or
Screen Matching.
7. In the Date/Time Settings section, set the date and time for the scheduled events to occur.
8. When you are finished, select Save and press Enter.
194
9. To schedule more events, repeat the previous steps as necessary.
10. Select Setup complete and select Yes to save your changes.
Viewing Scheduled Events
Editing a Scheduled Event
Parent topic: Adjusting Projector Features
Related tasks
Running Light Source Calibration
Related topics
Matching Tint and Brightness (Screen Matching)
Viewing Scheduled Events
You can view any currently scheduled events.
1. Press the Menu button.
2. Select the Extended menu and press Enter.
3. Select the Schedule Settings setting and press Enter.
You see a screen like this:
The colored boxes in the calendar indicate the following about the scheduled events:
One-time event
Recurring event
Communication is on/off
195
Event is invalid
Parent topic: Saving a Scheduled Event
Editing a Scheduled Event
You can edit any currently scheduled event.
1. Press the Menu button.
2. Select the Extended menu and press Enter.
3. Select the Schedule Settings setting and press Enter.
You see a screen like this:
4. Press the left or right arrow buttons to highlight the date on the calendar containing the scheduled
event you want to edit.
5. Press the up or down arrow buttons to highlight the event you want to edit, and press Esc.
6. Select one of the following:
•On/Off to enable or disable the selected event.
•Edit to edit the settings for the selected event.
•Clear to delete the selected event.
•Add New to add a new scheduled event.
7. When you are finished, select Return and press Enter.
196
8. Select Setup complete and select Yes to save your changes.
Note: To delete all scheduled events, select Schedule Reset and select Yes.
Parent topic: Saving a Scheduled Event
Copying Menu Settings Between Projectors
After you select menu settings for your projector, you can transfer them to another projector of the same
model.
Note: Copy the projector's settings before you adjust the projected image using the projector's Geometry
Correction settings. Any saved User's Logo setting on the projector will transfer to the other projector.
Caution: If the copy process fails due to a power failure, communication error, or for any other reason,
Epson will not be responsible for any repair costs incurred.
The following settings will not transfer between projectors:
• Network menu settings other than those in the Notifications and Others menus (when the Batch
Setup Range setting is set to Limited)
• EDID settings in the Signal menu (when the Batch Setup Range setting is set to Limited)
• Light Source Info in the Info menu
• Status Information in the Info menu
• Password-protected items
Note: In addition to the methods covered in this section, you can also copy and transfer settings to
multiple projectors over a network using the Epson Projector Management software. See the online
Epson Projector Management Operation Guide for instructions. You can download the latest software
and documentation from the Epson website.
Saving Settings to a USB Flash Drive
Transferring Settings from a USB Flash Drive
Saving Settings to a Computer
Transferring Settings from a Computer
Parent topic: Adjusting Projector Features
197
Related concepts
Password Security Types
Related references
Projector Feature Settings - Settings Menu
Projector Network and Camera Settings - Network Menu
Input Signal Settings - Signal Menu
Projector Information Display - Info Menu
Additional Projector Software and Manuals
Saving Settings to a USB Flash Drive
You can save the projector settings you want to transfer to a USB flash drive.
Note: Use an empty flash drive. If the drive contains other files, the transfer may not complete correctly.
The flash drive must use the FAT format and cannot have any security features.
1. Turn off the projector using the power switch.
2. Insert the flash drive into the USB-A port.
Note: Connect the flash drive directly to the projector. Do not use a hub or your settings may not be
saved correctly.
198
3. Press and hold the Esc button on the control panel or remote control as you turn on the power
switch.
4. When the On/Standby and Status lights are blue, and the Laser and Temp lights are orange, release
the Esc button.
The lights flash to indicate that settings are transferring to the flash drive. When the lights stop
flashing, the On/Standby light turns blue and the projector enters standby mode.
Caution: Do not unplug the power cord, turn off the power switch, or remove the flash drive while the
lights are flashing. This could damage the projector.
5. Once the projector enters standby mode, remove the flash drive.
Note: If the projector does not enter standby mode and the lights continue flashing, see the link
below for a solution.
Parent topic: Copying Menu Settings Between Projectors
Related references
Projector Light Status
Transferring Settings from a USB Flash Drive
After saving projector settings to a USB flash drive, you can transfer them to another projector of the
same model.
Note: Make sure the USB flash drive contains only a single settings transfer from another projector of
the same model. The settings are contained in a file called pjconfdata.bin. If the drive contains other
files, the transfer may not complete correctly.
Do not adjust image settings on a projector until after you transfer settings to it. Otherwise, you may have
to repeat your adjustments.
1. Turn off the projector using the power switch.
199
2. Insert the flash drive into the USB-A port.
Note: Connect the flash drive directly to the projector. Do not use a hub or your settings may not be
saved correctly.
3. Press and hold the Menu button on the control panel or remote control as you turn on the power
switch.
4. When the On/Standby and Status lights are blue, and the Laser and Temp lights are orange, release
the Menu button.
The lights flash to indicate that settings are transferring to the projector. When the lights stop
flashing, the On/Standby light turns blue and the projector enters standby mode.
Caution: Do not unplug the power cord, turn off the power switch, or remove the flash drive while the
lights are flashing. This could damage the projector.
5. Once the projector enters standby mode, remove the flash drive.
Note: If the projector does not enter standby mode and the lights continue flashing, see the link
below for a solution.
200
Parent topic: Copying Menu Settings Between Projectors
Related references
Projector Light Status
Saving Settings to a Computer
You can save the projector settings you want to transfer to a computer.
Your computer must be running one of the following operating systems:
• Windows Vista
• Windows 7
• Windows 8.x
• Windows 10
• OS X 10.7.x
• OS X 10.8.x
• OS X 10.9.x
• OS X 10.10.x
• OS X 10.11.x
• macOS 10.12.x
• macOS 10.13.x
• macOS 10.14.x
1. Turn off the projector using the power switch.
2. Connect a USB cable to your projector's Service port.
201
3. Connect the other end to any available USB port on your computer.
4. Press and hold the Esc button on the control panel or remote control as you turn on the power
switch.
5. When the On/Standby and Status lights are blue, and the Laser and Temp lights are orange, release
the Esc button.
The projector shows up as a removable disk on your computer.
6. Open the removable disk and copy the pjconfdata.bin file to your computer.
7. Once the file has copied, do one of the following:
•Windows: Open the My Computer,Computer,Windows Explorer, or File Explorer utility.
Right-click the name of your projector (listed as a removable disk) and select Eject.
•Mac: Drag the removable disk icon for your projector from the desktop into the trash.
The projector enters standby mode.
Note: If the projector does not enter standby mode and the lights continue flashing, see the link
below for a solution.
Parent topic: Copying Menu Settings Between Projectors
Related references
Projector Light Status
Transferring Settings from a Computer
After saving projector settings to a computer, you can transfer them to another projector of the same
model.
Your computer must be running one of the following operating systems:
• Windows Vista
• Windows 7
• Windows 8.x
202
• Windows 10
• OS X 10.7.x
• OS X 10.8.x
• OS X 10.9.x
• OS X 10.10.x
• OS X 10.11.x
• macOS 10.12.x
• macOS 10.13.x
• macOS 10.14.x
Do not adjust image settings on a projector until after you transfer settings to it. Otherwise, you may have
to repeat your adjustments.
1. Turn off the projector using the power switch.
2. Connect a USB cable to your projector's Service port.
3. Connect the other end to any available USB port on your computer.
4. Press and hold the Menu button on the control panel or remote control as you turn on the power
switch.
203
5. When the On/Standby and Status lights are blue, and the Laser and Temp lights are orange, release
the Menu button.
The projector shows up as a removable disk on your computer.
6. Copy the pjconfdata.bin file from your computer to the removable disk.
Note: Do not copy any other files to the removable disk.
7. Once the file has copied, do one of the following:
•Windows: Open the My Computer,Computer,Windows Explorer, or File Explorer utility.
Right-click the name of your projector (listed as a removable disk) and select Eject.
•Mac: Drag the removable disk icon for your projector from the desktop into the trash.
All the lights start flashing to indicate that the projector's settings are being updated. When the lights
stop flashing, the On/Standby light turns blue and the projector enters standby mode.
Caution: Do not turn off the power switch or unplug the power cord while the lights are flashing. This
could damage the projector.
Note: If the projector does not enter standby mode and the lights continue flashing, see the link
below for a solution.
Parent topic: Copying Menu Settings Between Projectors
Related references
Projector Light Status
204
Adjusting the Menu Settings
Follow the instructions in these sections to access the projector menu system and change projector
settings.
Using the Projector's Menus
Image Quality Settings - Image Menu
Input Signal Settings - Signal Menu
Projector Feature Settings - Settings Menu
Projector Setup Settings - Extended Menu
Projector Network and Camera Settings - Network Menu
Projector Information Display - Info Menu
Projector Reset Options - Reset Menu
Using the Projector's Menus
You can use the projector's menus to adjust the settings that control how your projector works. The
projector displays the menus on the screen.
1. Press the Menu button on the control panel or remote control.
205
You see the menu screen displaying the Image menu settings.
2. Press the up or down arrow button to move through the menus listed on the left. The settings for
each menu are displayed on the right.
Note: The available settings depend on the current input source, resolution, or other menu settings.
3. To change settings in the displayed menu, press Enter.
4. Press the up or down arrow button to move through the settings.
5. Change the settings using the buttons listed on the bottom of the menu screens.
6. To return all the menu settings to their default values, select Reset.
7. When you finish changing settings on a menu, press Esc.
8. Press Menu or Esc to exit the menus.
Parent topic: Adjusting the Menu Settings
206
Image Quality Settings - Image Menu
Settings on the Image menu let you adjust the quality of your image for the input source you are currently
using. The available settings depend on the currently selected input source.
To change settings for an input source, make sure the source is connected and select that source.
Setting Options Description
Color Mode See the list of available Color
Modes
Adjusts the vividness of image
colors for various image types
and environments
Brightness Varying levels available Lightens or darkens the overall
image
Contrast Varying levels available Adjusts the difference between
light and dark areas of the image
Color Saturation Varying levels available Adjusts the intensity of the image
colors
Tint Varying levels available Adjusts the balance of green to
magenta tones in the image
207
Setting Options Description
Sharpness Standard
Thin Line Enhancement
Thick Line Enhancement
Adjusts the sharpness of image
details
Standard: adjusts the overall
image sharpness
Thin Line Enhancement:
enhances fine details such as
hair and fabric patterns
Thick Line Enhancement:
enhances the outline,
background, and main parts of an
image to make them more clear
White Balance Color Temp.
G-M Correction
Customized
Adjusts the overall tint of the
image
Color Temp.: sets the color tone
based on color temperature
G-M Correction: higher values
tint the image blue and lower
values tint the image red
Customized: lets you adjust the
offset and gain of each color R
(red), G (green), and B (blue)
individually
208
Setting Options Description
Image Enhancement Image Preset Mode Selects the image enhancement
settings saved in advance
Frame Interpolation Smooths fast moving video by
comparing consecutive frames
and inserting an intermediate
frame between them
Deinterlacing Sets whether to convert
interlaced-to-progressive signals
for certain video image types
Off: for fast-moving video images
Video: for most video images
Film/Auto: for movies, computer
graphics, and animation
Noise Reduction Reduces flickering in analog
images
MPEG Noise Reduction Reduces the noise or artifacts
seen in MPEG video
Super resolution Sharpens blurred images
resulting from increasing
resolution
Detail enhancement Enhances details to create clear
outlines
Range: higher settings increase
the affected area around the
outline
Strength: higher settings create
a stronger effect
Advanced Gamma Adjusts the gamma levels of the
image. Select Customized to
adjust the gamma while viewing
the image or a graph.
RGBCMY Adjusts the hue, saturation, and
brightness for each color
209
Setting Options Description
Dynamic Contrast Off
Response Speed
Black Level
Adjusts the luminance of the
image to improve contrast by
tracking changes in image
brightness
Response Speed: select either
Normal to adjust brightness at
the standard speed or High
Speed to adjust brightness as
soon as the scene changes
Black Level: select the black
level you want to project when
the brightness level of the image
signal is zero; if you select 0%,
the light source turns off
Light Source Control Dynamic Contrast Automatically adjusts the amount
of light according to the
brightness of the image.
Lights-Out Control Automatically turns off the light
after a certain time has elapsed
while projecting at the specified
video level.
Lights-Out Signal Level: select
the brightness level for the
current video signal
Lights-Out Timer: select the
amount of time before the light
source automatically turns off
Note: The Brightness setting does not affect laser brightness. To change the laser brightness, use the
Brightness Settings in the Settings menu.
Parent topic: Adjusting the Menu Settings
Related concepts
Using Advanced Image Adjustment Features
210
Related references
Available Color Modes
Projector Feature Settings - Settings Menu
Related tasks
Adjusting Luminance Controls
Input Signal Settings - Signal Menu
Normally the projector detects and optimizes the input signal settings automatically. If you need to
customize the settings, you can use the Signal menu. The available settings depend on the currently
selected input source.
Note: You can restore the default settings of the Position,Tracking, and Sync settings by pressing the
Auto button on the remote control.
To change settings for an input source, make sure the source is connected and select that source.
211
Setting Options Description
Resolution Auto
Normal
Wide
Manual
Sets the input signal resolution
from an analog RGB computer
connection
Auto: detects the resolution
automatically
Normal: for 4:3 or 5:4 screens
Wide: for widescreen
Manual: lets you specify a
resolution
Aspect See the list of available aspect
ratios
Sets the aspect ratio (width-to-
height ratio) for the selected input
source
Tracking Varying levels available Adjusts signal to eliminate
vertical stripes in images from an
analog RGB computer
connection
Sync. Varying levels available Adjusts signal to eliminate
fuzziness or flickering in images
from an analog RGB computer
connection
Position Up, down, left, right Adjusts the image location on the
screen
Auto Setup On
Off
Automatically optimizes image
quality from an analog RGB
computer connection (when On)
Overscan Auto
Off
4%
8%
Changes the projected image
ratio to make the edges visible by
a selectable percentage or
automatically
212
Setting Options Description
Blanking Top
Bottom
Left
Right
Hides an area of the projected
image that you select using the
arrow buttons
Color Space Auto
BT.709
BT.2020
Sets the conversion system for
the color space
Selecting the incorrect color
space for the input source may
adversely affect the image
colors; the recommended setting
in most cases is Auto.
Dynamic Range Dynamic Range
HDR10 Setting
HLG Setting
Dynamic Range: sets the range
of dark and bright areas in
images; choose from Auto
(recommended), SDR,HDR10,
or HLG
HDR10 Setting: adjusts the
curve for the PQ (Perceptual
Quantizer) signal
HLG Setting: adjusts the curve
for the HDR HLG (Hybrid Log
Gamma) signal
213
Setting Options Description
Advanced Video Range Sets the video range to match
the setting of the device
connected to the HDMI,DVI-D,
HDBaseT, or SDI input ports
Input Signal Specifies the signal type from
input sources connected to
computer ports
Auto: detects signals
automatically
RGB: corrects color for
computer/RGB video inputs
Component: corrects color for
component video inputs
BNC Sync Termination Sets the termination for the signal
from the BNC port (set to Off
unless you need analog
termination, such as for
switchers)
EDID Describes the projector's display
capabilities to devices connected
to the HDMI, HDBaseT, DVI-D,
or DisplayPort input ports so you
can unify multiple displays
DDC Buffer If you are projecting using an
HDMI or DVI extension cable and
the image is not displayed
correctly, enabling this setting
may improve image quality
Scale Various scale options When using multiple projectors to
project one image, adjusts the
scale of the image displayed by
each projector
Parent topic: Adjusting the Menu Settings
215
Setting Options Description
Geometry Correction H/V-Keystone
Quick Corner
Curved Surface
Corner Wall
Point Correction
Memory
Adjusts the projected image
shape
H/V Keystone: lets you manually
correct the angles of the
horizontal and vertical sides
Quick Corner: select to adjust
the position of the four corners
Curved Surface: select to adjust
the image when projecting on a
curved surface
Corner Wall: select to adjust the
image when projecting on a
surface with a right angle
Point Correction: select to
display a grid and finely adjust
the image position
Memory: select to save
adjustment value of the
geometric correction and load it
when needed
Split Screen — Divides the viewing area
horizontally and displays two
images side-by-side
Lock Setting Control Panel Lock
Lens Lock
Controls projector button locking
to secure the projector
Control Panel Lock:
•Full Lock: locks all buttons
•Partial Lock: locks all buttons
except the power button
•Off: no buttons locked
Lens Lock: locks the focus,
zoom, and lens shift settings
216
Setting Options Description
Brightness Settings Light Source Mode
Brightness Level
Constant Brightness
Estimated Remains
Selects the brightness mode of
the projector
Light Source Mode: sets the
brightness for the light source
•Normal: maximum brightness
•Quiet: 70% brightness with
reduced fan noise
•Extended: 70% brightness
and extends the life
expectancy of the light source
•Custom: select a custom
brightness level and enable
use of next three settings
Brightness Level: select the
Custom brightness level you
want
Constant Brightness: maintains
a constant brightness (cannot
change the Light Source Mode
and Brightness Level settings)
Estimated Remains: displays
how long the projector can
maintain constant brightness (if
that setting is selected)
Remote Receiver Front/Rear
Front
Rear
Off
Limits reception of remote control
signals by the selected receiver;
Off turns off all receivers
User Button User1
User2
User3
Assigns a menu option to the
User1,User2, and User3
buttons on the remote control for
one-touch access
217
Setting Options Description
Test Pattern — Displays a test pattern to assist in
adjusting the image; select from
a variety of patterns
Memory Memory
Lens Position
Geometry Correction
Save customized sets of settings
to memory
Memory: loads, saves, erases,
or resets specific menu settings
Lens Position: saves the
position of the adjusted lens
Geometry Correction: saves the
geometry correction adjustments.
Parent topic: Adjusting the Menu Settings
Related concepts
Image Shape
Related tasks
Projecting Two Images Simultaneously
Locking the Projector's Lens Settings and Buttons
Saving Settings to Memory and Using Saved Settings
218
Projector Setup Settings - Extended Menu
Settings on the Extended menu let you customize various projector setup features that control its
operation.
Setting Options Description
Display — See the Display settings table in
this topic
User's Logo — Creates a screen that the
projector displays to identify itself
and enhance security
Projection Front
Front/Ceiling
Rear
Rear Ceiling
Selects the way the projector
faces the screen so the image is
oriented correctly
Operation — See the Operation settings table
in this topic
219
Setting Options Description
A/V Settings A/V Output Select Always On to set a fixed
IP address and move the lens to
the home position when the
projector is in standby mode (the
Standby Mode setting must be
set to Communication On)
Standby Mode Communication On
Communication Off
Enable this setting to allow the
following operations to occur
when the projector is in standby
mode:
• Monitor and control the
projector over a network
• Output video to an external
device (A/V Output must be
set to Always On)
• Communication from the
HDBaseT port (Control
Communications must be set
to On in the HDBaseT
settings)
HDBaseT Control Communications
Extron XTP
Selects the communication
settings for connections to an
HDBaseT transmitter or switcher
Control Communications:
enables or disables
communication from the Ethernet
and serial ports on the
transmitter; turning on this setting
disables the projector's LAN,RS-
232C, and Remote ports (Extron
XTP must be turned off to use
this setting)
Extron XTP: set to On when you
connect an Extron XTP
transmitter or switcher to the
HDBaseT port
220
Setting Options Description
SDI Settings Link Type
Manual Settings
Select the signal settings for the
SDI port
Link Type: select Single (Auto)
to let the projector read the
payload ID for the input signal
and automatically display the
image, or select Single (Manual)
when you know the type of input
signal and want to select the
same signal in the Manual
Settings options
Manual Settings: set various
SDI settings manually or reset
them to their default values
Color Calibration Start Auto Adjustment
Undo
Redo
Color Uniformity
Automatically detects color
deterioration and adjusts the
color tone
Start Auto Adjustment:
automatically adjusts the color
tone for the whole image
Undo and Redo: undoes or
redoes the auto adjustment
Color Uniformity: adjusts the
color tone balance for the whole
image
221
Setting Options Description
Multi-Projection Projector ID
Projector Grouping
Tiling
Geometry Correction
Edge Blending
Black Level
Scale
Screen Matching
Select various options when
projecting from multiple
projectors
Projector ID: sets the projector
to a particular ID number which
allows you to use a remote
control to individually control
projectors
Projector Grouping: lets you
select the projectors being used
to project one image
Tiling: sets the number of split
screens and the position of each
image
Geometry Correction: corrects
image distortion
Edge Blending: blends the
border between multiple images
to create a seamless screen
Black Level: adjusts the
brightness and tone differences
in overlapping images
Scale: adjusts the scale of the
images
Screen Matching: adjusts the
tint and brightness of the images
Schedule Settings Various scheduling options Lets you schedule various
projector tasks
Language Various languages available Selects the language for
projector menu and message
displays (not changed by Reset
option)
Display settings
222
Setting Description
Menu Position Selects the position of the projector menu displayed on the
screen
Message Position Selects the position of messages displayed on the screen
Messages Controls whether messages are displayed on the screen
Display Background Selects the screen color or logo to display when no signal is
received
Startup Screen Controls whether a special screen appears when the projector
starts up
Standby Confirmation Displays a confirmation message after pressing the Standby
button on the remote control
Air Filter Notice Displays a message when a clog in the air filter is detected
Screen Sets the aspect ratio and position of the projected image
according to the type of screen being used
Panel Alignment Corrects color misalignment in the projected image
Color Uniformity Adjusts the color tone balance
OSD Rotation Rotates the menu display 90°
Operation settings
Setting Description
Direct Power On Turns on the projector when you plug it in
Sleep Mode Automatically places the projector in standby mode after an
interval of inactivity
Sleep Mode Timer Sets the time before the projector automatically turns off (Sleep
Mode must be turned on)
High Altitude Mode Regulates the projector’s operating temperature at altitudes
above 4921 feet (1500 m)
Startup Source Search Automatically detects the image signal being input when the
projector is turned on
223
Setting Description
Shutter Settings Adjusts the shutter settings
Fade-in: sets the number of seconds for a fade-in transition
effect when displaying an image
Fade-out: sets the number of seconds for a fade-out transition
effect when hiding an image
Shutter Timer: turns off the projector automatically after using
the shutter and 2 hours of inactivity has passed
Shutter Release: select Shutter if you want to use only the
Shutter button to turn off the shutter, or select Any Button to
use any button to turn it off
Startup: select the shutter status for when you turn on the
projector
Standby: select the shutter status for when the projector is in
standby mode or select Last Used to maintain the current
shutter status when you turn off the projector
Video Terminal Settings Enables or disables each video input port
Advanced See the next table in this topic
Date & Time Adjusts the projector's time and date settings
Lens Calibration Displays information about the lens currently in use and lets
you start lens calibration
Advanced settings
Setting Description
Beep Controls the beep that sounds when you turn the projector on
or off
Indicators Select Off to turn off projector lights, except warning lights
Log Save Destination Select where you want to save projector operation log files
Batch Setup Range Select which projector menu settings to copy using the batch
setup feature; select All or select Limited to not copy the EDID
settings or all Network menu settings (except the Notifications
and Others menu settings)
224
Setting Description
AC Voltage Monitoring Select Off to regularly use the direct shutdown feature; if you
select On for this setting and the projector is turned off by any
method other than pressing the power button, a power supply
voltage warning message is displayed the next time the
projector is turned on
Lens Type Select the model number of the lens if you installed any of
these lenses: ELPLS04, ELPLU02, ELPLR04, ELPLW04,
ELPLM06, ELPLM07, or ELPLL07
Parent topic: Adjusting the Menu Settings
Related concepts
Using Multiple Projectors
Related tasks
Saving a User's Logo Image to Display
Running Light Source Calibration
Saving a Scheduled Event
Shutting Off the Picture Temporarily
Turning Off the Projector
Related topics
Copying Menu Settings Between Projectors
Attaching and Removing a Lens
225
Projector Network and Camera Settings - Network Menu
Settings on the Network menu let you view network information and set up the projector for monitoring
and control over a network. You can also control access to a remote camera.
Setting Options Description
Wireless Mode Wireless LAN On
Off
Enable or disable wireless
communication
226
Setting Options Description
Net. Info - Wireless LAN Connection mode
Wireless LAN Sys.
Antenna level
Projector Name
SSID
DHCP
IP Address
Subnet Mask
Gateway Address
MAC Address
Region Code
IPv6
Displays wireless network status
and details
Net. Info - Wired LAN Projector Name
DHCP
IP Address
Subnet Mask
Gateway Address
MAC Address
IPv6 Address (Manual)
IPv6 Address (Auto)
Displays wired network status
and details
Display the QR Code — Displays the QR Code
Network Configuration Accesses additional network
menus
Configures your network settings
227
Setting Options Description
Remote Camera Access Remote Camera Access
Password
Enables or disables the remote
camera and lets you set a
password to limit access to
changing the remote camera
setting or capturing the projected
image using Web Control
Parent topic: Adjusting the Menu Settings
Related concepts
Wired Network Projection
Wireless Network Projection
Related tasks
Using a QR Code to Connect a Mobile Device
Viewing an Image Capture of the Displayed Image from a Remote Location
Projector Information Display - Info Menu
You can display information about the projector and input sources by viewing the Info menu. However,
you cannot change any settings in the menu.
228
Setting Options Description
Projector Info Operation Hours Displays the number of hours the
projector has been used since it was
turned on
Source Displays the name of the port to which
the current input source is connected
Input Signal Displays the input signal setting of the
current input source
Resolution Displays the resolution of the current
input source
Refresh Rate Displays the refresh rate of the current
input source
Sync Info Displays information that may be
needed by a service technician
Color Format Displays information about the color
space and dynamic range
Status Displays information about projector
problems that may be needed by a
service technician
Serial Number Displays the projector's serial number
Lens Type Displays the model number of the
installed lens
Event ID Displays the Event ID number
corresponding to a specific projector
problem; see the list of Event ID
codes
HDBaseT Signal Level Displays the image signal information
from the HDBaseT port
229
Setting Options Description
Light Source Info Light Source Hours Displays the number of operating
hours for each of the projector's Light
Source Mode settings
Estimated Remains If the Constant Brightness setting is
enabled, displays the remaining
number of hours the projector can
maintain constant brightness
Version Main
Video2
Sub
Sub2
HDBaseT
HDBaseT2
SDI
Status Monitor
AC Monitor
Displays the projector's firmware
information
Version (Slot) Slot1
Slot2
Displays the version information of the
interface board connected to the
indicated slot
Status Information — Displays basic status information
Voltage Warning Info — Displays power voltage warning
information
Temp Warning Info — Displays various high temperature
warning information
Power On/Off History — Displays the projector's power on and
power off history
Event ID Code List
Parent topic: Adjusting the Menu Settings
230
Event ID Code List
If the Event ID option on the Info menu displays a code number, check this list of Event ID codes for the
solution to the projector problem associated with the code.
Event ID code Cause and solution
0432 Turn the projector off and then on again.
0435
0434 Unstable network communication. Check the network communication status, wait a
few moments, and try connecting to the network again.
0482
0484
0485
0433 Cannot display the transferred images. Restart the network software.
0481 Communication with computer was disconnected. Restart the network software.
0483
04FE
The network software quit unexpectedly. Check the network communication status,
then turn the projector off and then on again.
0479
04FF
A projector system error has occurred. Turn the projector off and then on again.
0891 Cannot find an access point with the same SSID. Set your computer, access point,
and projector to the same SSID.
0892 The WPA/WPA2 authentication type does not match. Make sure the wireless
network security settings are correct.
0893 The TKIP/AES encryption type does not match. Make sure the wireless network
security settings are correct.
0894 Communication with unauthorized access point was disconnected. Contact your
network administrator.
0898 Failed to acquire DHCP. Make sure the DHCP server is operating correctly. If you
are not using DHCP, turn off the DHCP setting in the Network menus.
0899 Communication error. Turn the projector off and then on again.
231
Event ID code Cause and solution
089A
089B
089C
089D
EAP authentication error. Make sure the wireless network security settings are
correct.
0920 The internal power supply is running low. Contact Epson support.
Parent topic: Projector Information Display - Info Menu
Projector Reset Options - Reset Menu
You can reset most of the projector settings to their default values using the Reset All Config option on
the Reset menu.
You can also reset the saved names and settings in the Save Memory list using the Reset All Memories
option.
To reset all settings to the factory default (except for password protected settings), select the Reset All
(Factory Default) option. You need to enter a password to reset the settings. The default password is
0000, which you should change to your own password.
You cannot reset the following settings using the Reset All Config option:
• Input Signal
• Memory
232
• User's Logo
• Network menu items
• Language
• Date & Time
• Panel Alignment
• Color Uniformity
• Lens Calibration
• Color Calibration
• Projector Grouping
• Screen Matching
• Color Matching
Parent topic: Adjusting the Menu Settings
Related references
Projector Network and Camera Settings - Network Menu
Related tasks
Saving Settings to Memory and Using Saved Settings
233
Maintaining and Transporting the Projector
Follow the instructions in these sections to maintain your projector and transport it from place to place.
Projector Maintenance
Transporting the Projector
Projector Maintenance
Your projector needs little maintenance to keep working at its best.
You may need to clean the lens periodically, and clean the air filter and air vents to prevent the projector
from overheating due to blocked ventilation.
The only parts you should replace are the air filter and remote control batteries. If any other part needs
replacing, contact Epson or an authorized Epson servicer.
This projector uses a sealed laser light source which does not need servicing and cannot be replaced.
Warning: Before cleaning any part of the projector, turn it off, wait for it to beep, and unplug the power
cord. Never open any cover on the projector, except as specifically explained in this manual. Dangerous
electrical voltages in the projector can injure you severely.
Warning: Do not try to service this product yourself, except as specifically explained in this manual.
Refer all other servicing to qualified servicers.
Cleaning the Lens
Cleaning the Projector Case
Air Filter and Vent Maintenance
Replacing the Remote Control Batteries
Parent topic: Maintaining and Transporting the Projector
Related tasks
Turning Off the Projector
Cleaning the Lens
Clean the projector's lens periodically, or whenever you notice dust or smudges on the surface.
• To remove dust or smudges, gently wipe the lens with lens-cleaning paper.
234
• To remove stubborn smudges, moisten a soft, lint-free cloth with lens cleaner and gently wipe the
lens. Do not spray any liquid directly on the lens.
Warning: Do not use a lens cleaner that contains flammable gas. The high heat generated by the
projector may cause a fire.
Caution: Do not use glass cleaner or any harsh materials to clean the lens and do not subject the lens
to any impacts; you may damage it. Do not use canned air, or the gases may leave a residue. Avoid
touching the lens with your bare hands to prevent fingerprints on or damage to the lens surface.
Parent topic: Projector Maintenance
Cleaning the Projector Case
Before cleaning the projector case, turn off the projector, wait for it to beep, and unplug the power cord.
• To remove dust or dirt, use a soft, dry, lint-free cloth.
• To remove stubborn dirt, use a soft cloth moistened with water and mild soap. Do not spray liquid
directly on the projector.
Caution: Do not use wax, alcohol, benzine, paint thinner, or other chemicals to clean the projector
case. These can damage the case. Do not use canned air, or the gases may leave a flammable
residue.
Parent topic: Projector Maintenance
Related tasks
Turning Off the Projector
Air Filter and Vent Maintenance
Regular filter maintenance is important to maintaining your projector. Your Epson projector is designed
with an easily accessible, user-replaceable filter to protect your projector and make regular maintenance
simple. Filter maintenance intervals will depend on the environment.
If regular maintenance is not performed, your Epson projector will notify you when the temperature
inside the projector has reached a high level. Do not wait until this warning appears to maintain your
projector filter as prolonged exposure to high temperatures may reduce the life of your projector or laser.
Damage due to the failure to properly maintain the projector or its filter may not be covered by the
projector's Limited Warranty.
Cleaning the Air Filters and Air Intake Vents
235
Replacing the Air Filters
Parent topic: Projector Maintenance
Related references
Projector Light Status
Cleaning the Air Filters and Air Intake Vents
You need to clean the projector's air filters and air intake vents in the following situations:
• The filters or vents get dusty.
• You see a message telling you to clean it.
Note: To receive air filter notifications, make sure the Air Filter Notice setting is set to On in the
Extended menu Display settings.
• The projector's Filter light flashes orange.
Note: The projector has two air filters on the front. The illustrations here show cleaning the air filter on
the right, but the steps are the same to clean either filter.
1. Turn off the projector, wait for the projector to beep, and unplug the power cord.
236
2. Loosen the screw securing the air filter cover and open the air filter cover as shown. (It is attached
with a cord.)
3. Grasp the tab on the air filter and pull it out of the projector.
237
4. Tap each side of the air filter 4 to 5 times to shake off any excess dust.
Caution: Do not use excessive force when tapping the air filter, or it may crack and become
unusable. Do not rinse the air filter in water, or use any detergent or solvent to clean it. Do not use
canned air; the gases may leave a residue, or push dust and debris into the projector's optics or
other sensitive areas.
5. Vacuum the front of the air filter (the side with the tabs) to remove any remaining dust.
Note: If dust is difficult to remove or the air filter is damaged, replace the air filter.
238
6. Place the air filter back in the projector as shown and push gently until it clicks into place.
7. Insert the tabs on the right side of the air filter cover into the notches in the projector. Then close the
air filter cover and tighten the screw to secure it.
8. Repeat these steps to clean the other air filter.
239
9. Use a vacuum cleaner or soft, long-bristle brush to carefully remove dust from the air intake vents on
the side and bottom of the projector.
Note: Clean the projector's air intake vents periodically, or whenever you notice dust on the side or
bottom of the projector.
Parent topic: Air Filter and Vent Maintenance
Related references
Projector Light Status
Projector Setup Settings - Extended Menu
Related tasks
Replacing the Air Filters
Replacing the Air Filters
You need to replace the air filters in the following situations:
• After cleaning an air filter, you see a message telling you to clean or replace it.
• An air filter is torn or damaged.
240
Note: To receive air filter notifications, make sure the Air Filter Notice setting is set to On in the
Extended menu Display settings.
You can replace the air filters while the projector is mounted to the ceiling or placed on a table.
Note: The projector has two air filters. The illustrations here show replacing the air filter on the right, but
the steps are the same to replace either filter.
1. Turn off the projector, wait for the projector to beep, and unplug the power cord.
2. Loosen the screw securing the air filter cover and open the air filter cover as shown. (It is attached
with a cord.)
241
3. Grasp the tab on the air filter and pull it out of the projector.
Note: Air filters contain polypropylene. Dispose of used air filters according to local regulations.
4. Place the new air filter in the projector as shown and push gently until it clicks into place.
242
5. Insert the tabs on the right side of the air filter cover into the notches in the projector. Then close the
cover and tighten the screw securing it.
6. Repeat these steps to replace the other air filter.
Parent topic: Air Filter and Vent Maintenance
Related references
Projector Setup Settings - Extended Menu
Replacing the Remote Control Batteries
The remote control uses two AA manganese or alkaline batteries. Replace the batteries as soon as they
run out.
Caution: Use only the type of batteries specified in this manual. Do not install batteries of different types,
or mix new and old batteries.
243
1. Remove the battery cover as shown.
2. Remove the old batteries.
Warning: If the battery fluid has leaked, wipe it away with a soft cloth and avoid getting the fluid on
your hands. If it gets on your hands, wash them immediately to avoid injury.
3. Insert the batteries with the +and –ends facing as shown.
244
4. Replace the battery cover and press it down until it clicks into place.
Warning: Dispose of used batteries according to local regulations. Do not expose batteries to heat
or flame. Keep batteries out of the reach of children; they are choking hazards and are very
dangerous if swallowed.
Parent topic: Projector Maintenance
Transporting the Projector
The projector contains precision parts, some of which are glass. Follow the guidelines here to transport,
ship, or store the projector safely.
Caution: Use three or more people to unpack or lift the projector.
Warning: When moving the projector, do not hold the lens replacement cover. It may come off and the
projector may fall, which could cause an injury.
1. Turn the projector off, wait for it to beep, and remove any equipment connected to the projector.
2. If you are packing the projector to transport it a long distance, remove the lens unit and attach the
cap for the lens cover.
3. To lift or lower the projector, install four commercially available eye bolt screws M6 (up to a depth of
27 mm) to the screw thread holes in each corner of the projector. Attach straps or chains to the
245
screws and make sure the angle of the strap is 60 degrees or more when lifting or lowering the
projector.
Caution: Do not lift the projector with the front, back, or side of the projector facing up.
Caution: Do not use the eye bolt screws for permanent installation as this can cause damage.
4. Do one of the following:
• When transporting the projector a long distance or as checked luggage, pack it in a firm box with
cushioning around it and mark the box "Fragile."
• When shipping the projector for repairs, place it in its original packing materials, if possible, or use
equivalent materials with cushioning around the projector. Mark the box "Fragile."
Note: Epson shall not be liable for any damages incurred during transportation.
247
Solving Problems
Check the solutions in these sections if you have any problems using the projector.
Projection Problem Tips
Projector Light Status
Viewing Projector Status Information
Using the Projector Help Displays
Solving Image Problems
Solving Projector or Remote Control Operation Problems
Solving Network Problems
Where to Get Help
Projection Problem Tips
If the projector is not working properly, try turning it off and unplugging it. Then plug it back in and turn it
on.
If this does not solve the problem, check the following:
• The lights on the projector may indicate what the problem is.
• The projector's Help system can display information about common problems, if the projector is
operating.
• The projector's LCD screen can display information about the projector's status.
• The solutions in this manual can help you solve many problems.
If none of these solutions help, you can contact Epson for technical support.
Parent topic: Solving Problems
Related references
Projector Light Status
Where to Get Help
Related tasks
Using the Projector Help Displays
Viewing Projector Status Information
248
Projector Light Status
The lights on the projector indicate the projector status and let you know when a problem occurs. Check
the status and color of the lights and look for a solution in the table here.
1 LAN (wired network or HDBaseT status)
2 WLAN (wireless network status)
3 Filter light
4 Temp (temperature) light
5 Laser light
6 Status light
7 On/Standby light
On/Standby
(power) light
Status
light
Laser
light
Temp light Filter
light
Status and solution
Blue Off Off Off Off Projector is in standby mode or
network monitoring and control is in
progress.
Blue Flashing
blue
Varies Off Off Warming up. Wait for an image to
appear.
Blue Blue Varies Off Off Normal operation.
249
On/Standby
(power) light
Status
light
Laser
light
Temp light Filter
light
Status and solution
Blue Blue Flashing
orange
fast
Off Off Projector is connected to a 110 V
power source and the laser is
operating at approximately 55% of
available power.
For optimal performance, connect
the projector to a 220 V power
source using the 220 V power cord
that came with the projector.
Blue Flashing
blue
Off Off Off Cooling down. All buttons are
disabled.
Flashing blue Off Off Off Off Preparing network monitoring. (Wait
for the light to remain orange before
unplugging the projector.)
Blue Blue Flashing
blue
Off Off The shutter feature is enabled.
Off Flashing
blue
Flashing
orange
Off Off Internal error. Turn off the projector,
unplug the power cord, and contact
Epson for help.
Off Flashing
blue
Off Flashing
orange
Off A fan or sensor has a problem. Turn
off the projector, unplug the power
cord, and contact Epson for help.
250
On/Standby
(power) light
Status
light
Laser
light
Temp light Filter
light
Status and solution
Off Flashing
blue
Off Orange Off Projector is too hot. Wait for about
five minutes so the projector can
switch to standby mode. Then check
the following:
• Make sure that the vents and air
filter are not clogged with dust or
obstructed by nearby objects.
• Clean or replace the air filter.
• Make sure the environmental
temperature is not too hot.
• If operating the projector at high
altitude, turn on High Altitude
Mode.
• If the problem persists, unplug the
projector and contact Epson for
help.
Off Flashing
blue
Orange Off Off Laser error.
• Make sure that the vents and air
filter are not clogged with dust or
obstructed by nearby objects.
• Clean or replace the air filter.
• If the problem persists, unplug the
projector and contact Epson for
help.
Off Flashing
blue
Off Off Orange Low air flow through the projector.
• Make sure that the vents and air
filter are not clogged with dust or
obstructed by nearby objects.
• Clean or replace the air filter.
• If the problem persists, unplug the
projector and contact Epson for
help.
251
On/Standby
(power) light
Status
light
Laser
light
Temp light Filter
light
Status and solution
Off Flashing
blue
Orange Orange Off No lens installed, or lens shift or
supply voltage error. Remove and
reinstall the lens. If the problem
persists, turn off the projector, unplug
the power cord, and contact Epson
for help
Off Flashing
blue
Flashing
orange
Flashing
orange
Off Shutter error. Turn off the projector,
unplug the power cord, and contact
Epson for help.
Flashing blue Varies Varies Flashing
orange
Varies High temperature warning. If the
temperature gets too high, projection
will automatically stop.
• Make sure that the vents and air
filter are not clogged with dust or
obstructed by nearby objects.
• Make sure the environmental
temperature is not too hot.
• Clean or replace the air filter.
Varies Varies Varies Varies Flashing
orange
Clean the air filter.
Flashing blue Varies Flashing
orange
Varies Varies Laser warning. Turn off the projector,
unplug the power cord, and contact
Epson for help.
Flashing blue Varies Flashing
orange
Varies Varies An unsupported lens is attached.
Attach only a supported lens.
Flashing blue Varies Flashing
orange
Flashing
orange
Varies Shutter error. Turn off the projector,
unplug the power cord, and contact
Epson for help.
252
On/Standby
(power) light
Status
light
Laser
light
Temp light Filter
light
Status and solution
Flashing blue Varies Varies Varies Orange Low air flow through the air filter.
• Make sure that the vents and air
filter are not clogged with dust or
obstructed by nearby objects.
• Clean or replace the air filter.
• If the problem persists, unplug the
projector and contact Epson for
help.
Varies Varies Flashing
orange
Varies Varies End of Constant Brightness mode.
Varies Off Flashing
orange
fast
Flashing
orange fast
Varies When performing batch setup using
a USB flash drive, the setup file may
be corrupt or the USB flash drive
may not be connected correctly.
Remove the USB flash drive, turn off
the projector and unplug the power
cord, then plug the power cord back
in, turn on the projector, and try
again.
Flashing blue
fast
Off Flashing
orange
fast
Flashing
orange fast
Flashing
blue fast
When performing batch setup, an
error may have occurred when
writing the settings. Turn off the
projector, unplug the power cord, and
contact Epson for help.
LAN light WLAN light Status and solution
Blue — You can use a wired LAN or HDBaseT
transmitter
Off — Cannot use wired LAN or HDBaseT
transmitter. Check the LAN cable
connection and your LAN or HDBaseT
transmitter settings.
— Blue Wireless LAN is available.
253
LAN light WLAN light Status and solution
— Flashing blue quickly Connecting to a device.
— Flashing blue slowly Wireless error. Turn the projector off and
then on again.
— Off Wireless LAN is unavailable. Check your
wireless LAN settings.
Note: If the lights display a pattern not listed in the table above, turn the projector off, unplug it, and
contact Epson for help.
Parent topic: Solving Problems
Related concepts
Air Filter and Vent Maintenance
Wired Network Projection
Wireless Network Projection
Related references
Projector Setup Settings - Extended Menu
Optional Equipment and Replacement Parts
Projector Feature Settings - Settings Menu
Where to Get Help
Related tasks
Turning On the Projector
Shutting Off the Picture Temporarily
Turning Off the Projector
Related topics
Attaching and Removing a Lens
Copying Menu Settings Between Projectors
Viewing Projector Status Information
You can monitor the projector's status and view error information on the LCD screen.
Note: You can also view the projector's status in the Info menu. Press the ibutton on the remote control
and select Status Information.
254
1. Turn on the projector.
2. Press the light button on the control panel.
3. Press the left or right arrow button to view different categories of information.
•Status Information: the projector's operating status
•Source: input signal information
•Signal Information: input digital signal information
•Network Wired: wired LAN settings
•Network Wireless: wireless LAN settings
•Maintenance: operating time for the projector and light source
•Version: projector's firmware version
•Setting: lets you adjust the LCD screen contrast and the length of time the screen remains lit
when you press the light button
4. Press the up or down arrow button to scroll through the information on the screen.
255
1 Item name
2 Status information
Projector Status Display Messages
Parent topic: Solving Problems
Related references
Projector Information Display - Info Menu
Projector Status Display Messages
Categories on the status display screens let you view information about the projector and its operation.
Status Information category
Information Description
System See the System status information table at the end
of this topic
Last Warn/Err Displays the most recent warnings and errors
displayed by the projector
Source Displays the source currently being used
On-Screen Display Displays the settings for on-screen displays. When
turned off, menus or messages are not displayed
on the projected images
Shutter Displays the shutter status
Shutter Startup Displays the shutter Startup settings
Shutter Standby Displays the shutter Standby settings
Intake Air Temp Displays the air intake temperature
Internal Temp Lv Displays the projector's internal temperature
AC Voltage Displays warnings and errors that have occurred
when the AC Voltage Monitoring setting is turned
on
Laser Status Displays the operating status of the light source
256
Information Description
SLOT1 Model Displays the name of the interface board installed
in Slot 1.
SLOT1 Condition Displays the status of the interface board installed
in Slot 1.
SLOT1 Board ID Displays the ID of the interface board installed in
Slot 1.
SLOT1 Board Ver Displays the version of the interface board
installed in Slot 1.
SLOT2 Model Displays the name of the interface board installed
in Slot 2.
SLOT2 Condition Displays the status of the interface board installed
in Slot 2.
SLOT2 Board ID Displays the ID of the interface board installed in
Slot 2.
SLOT2 Board Ver Displays the version of the interface board
installed in Slot 2.
Source category
Information Description
Source Displays the source currently being used
Resolution Displays the resolution of the current input signal
Color Space Displays the color space of the current input signal
H-Frequency Displays the horizontal frequency of the current
input signal
V-Frequency Displays the vertical frequency of the current input
signal
Sync Polarity Displays the sync polarity
Sync Mode Displays the sync type
Detected Mode Displays the detected mode of the current input
signal
257
Information Description
Transport Displays the scanning method
Video Range Displays the video range of the projector
Signal Information category
Information Description
5V Detect Displays the detection results of 5V signals
TMDS Clock Displays the TMDS frequency of the current input
signal
H-Frequency Displays the horizontal frequency of the current
input signal
V-Frequency Displays the vertical frequency of the current input
signal
Stable Time Displays the amount of operating time since the
input source was determined
HDCP Status Displays the HDCP status
HDCP Ver Displays the HDCP version
AVI VIC Displays the VIC information (AVI) of the current
input signal
AVI Sampling Str Displays color sampling for AVI
Signal Mode Displays the signal mode
Color Space Displays the color space conversion method
HDR Mode Displays the HDR mode
EDID Mode Displays the EDID mode
HDBaseT Level Displays the image signal from the HDBaseT port
SDI Link Mode Displays the linking type for SDI
Sync Detect Displays the results of signal detection for each
SDI port
PayloadID Detect Displays the results of SDI payload ID detection
258
Information Description
Resolution Displays the resolution
Refresh Rate Displays the refresh rate for SDI
Color Sampling Displays the color sampling
Pixel Depth Displays the color depth for SDI
SDI Type Displays the type for SDI
Division Type Displays the split transmission method for SDI
3G Mapping Level Displays the mapping level for 3G-SDI
Network Wired category
Information Description
Projector Name Displays the name used to identify the projector
when connected to a network
Connection Mode Displays the connection path for the LAN
DHCP Displays the DHCP display settings
IP Display Displays the IP address display settings
IP Address Displays the IP address
MAC Address Displays the MAC address
Network Wireless category
Information Description
Projector Name Displays the name used to identify the projector
when connected to a network
Connection Mode Displays the connection mode to use when
connecting the projector and a computer over a
wireless LAN
SSID Display Displays the SSID display settings
IP Display Displays the IP address display settings
SSID Displays the SSID
259
Information Description
IP Address Displays the IP address
DHCP Displays the DHCP settings
MAC Address Displays the MAC address
Security Displays the security settings
Antenna Level Displays the reception status for Wi-Fi
Maintenance category
Information Description
Operation Time Displays the projector's total operation time
Laser Op. Time Displays the laser operating time for each Light
Source Mode setting
Service Info LBL Displays information for the light source
Version category
Information Description
Serial No. Displays the projector's serial number
Main Display the projector's firmware version
information
Video2
Sub
Sub2
HDBaseT
Status Monitor
System status information
Status Description
OK The projector is in normal operating mode
Warm-up The projector is warming up
260
Status Description
Standby The projector is in standby mode
Cool Down The projector is cooling down
Temp Error A high temperature error occurred
Fan Error A fan error occurred
Sensor Error A sensor error occurred
Internal Error An internal error occurred
Airflow Error A filter airflow error occurred
Temp Warning A high temperature warning occurred
Internal Warning A warning regarding the internal system occurred
Airflow Decline A low airflow error occurred
Clean Filter An air filter notice occurred; clean the air filter
Lens Error A lens error has occurred
Laser Error A laser error has occurred
Laser Warning A laser warning has occurred
Parent topic: Viewing Projector Status Information
Using the Projector Help Displays
You can display information to help you solve common problems using the projector's Help system.
Note: Before using the Help system, assign Help to one of the User buttons.
1. Turn on the projector.
2. Press the User button assigned to Help.
You see the Help menu.
3. Use the up and down arrow buttons to highlight the problem you want to solve.
4. Press Enter to view the solutions.
261
5. When you are finished, do one of the following:
• To select another problem to solve, press Esc.
• To exit the help system, press the Menu button.
Parent topic: Solving Problems
Related references
Projector Feature Settings - Settings Menu
Solving Image Problems
Check the solutions in these sections if you have any problems with projected images.
Solutions When No Image Appears
Solutions When "No Signal" Message Appears
Solutions When "Not Supported" Message Appears
Solutions When Only a Partial Image Appears
Solutions When the Image is Not Rectangular
Solutions When the Image Contains Noise or Static
Solutions When the Image is Fuzzy or Blurry
Solutions When the Image Brightness or Colors are Incorrect
Solutions When Automatic Adjustments are not Applied Correctly
Parent topic: Solving Problems
Solutions When No Image Appears
If no image appears, try the following solutions:
• Make sure the lens cap is off.
• Press the Shutter button on the remote control to see if the image was temporarily turned off.
• Make sure all necessary cables are securely connected and the power is on for the projector and
connected video sources.
• Make sure the image being projected is not completely black (only when projecting computer images).
• Press the projector's power button to wake it from standby or sleep mode. Also see if your connected
computer is in sleep mode or displaying a blank screen saver.
• Press the Menu button. If the projector menu displays, there may be a problem with the connected
video source, cable connection, or port.
262
• Check the settings on the Signal menu to make sure they are correct for the current video source. If
you are using the SDI In port, make sure the SDI Settings options are set correctly on the Extended
menu.
• Adjust the Brightness Settings.
• Check the Display setting to make sure Messages is set to On.
• For images projected with Windows Media Center, reduce the screen size from full screen mode.
• For images projected from applications using Windows DirectX, turn off DirectX functions.
• If you are projecting from a laptop computer, make sure it is set up to display on an external monitor.
• If you are using other display equipment with the projector, make sure the EDID settings are set
correctly on the Signal menu. You may need to disconnect the other equipment and select EDID
settings again.
• If you connected an external monitor to the projector and nothing appears on it, make sure the
projector is not in standby mode. Also make sure you connected the external monitor to the correct
port for your video source.
• If the other solutions do not solve the problem, reset all of the projector settings using the options on
the Reset menu.
Parent topic: Solving Image Problems
Related concepts
Projector Connections
Related references
Input Signal Settings - Signal Menu
Projector Setup Settings - Extended Menu
Projector Reset Options - Reset Menu
Related tasks
Shutting Off the Picture Temporarily
Connecting to an External Computer Monitor
Solutions When "No Signal" Message Appears
If the "No Signal" message appears, try the following solutions:
• Press the Search button on the remote control and wait a few seconds for an image to appear. You
can also press the source button for the video source on the projector's control panel or remote
control.
263
• Turn on the connected computer or video source, and press its play button to begin your presentation,
if necessary.
• Check the connection from the projector to your video sources.
• If you are projecting from a laptop computer, make sure it is set up to display on an external monitor.
• If necessary, turn the projector and the connected computer or video source off and then on again.
• Try a different video cable.
• If the other solutions do not solve the problem, reset all of the projector settings using the options on
the Reset menu.
Displaying From a PC Laptop
Displaying From a Mac Laptop
Parent topic: Solving Image Problems
Related concepts
Projector Connections
Related references
Projector Reset Options - Reset Menu
Related tasks
Selecting an Image Source
Displaying From a PC Laptop
If you see the "No Signal" message when you display from a PC laptop, you need to set up the laptop to
display on an external monitor.
1. Hold down the laptop's Fn key and press the key labeled with a monitor icon or CRT/LCD. (See your
laptop manual for details.) Wait a few seconds for an image to appear. To display on both the
laptop's monitor and the projector, try pressing the same keys again.
Note: On Windows 7 or later, hold down the Windows key and press Pat the same time, then click
Duplicate.
2. If the same image is not displayed by the laptop and projector, check the Windows Display utility to
make sure the external monitor port is enabled and extended desktop mode is disabled. (See your
computer or Windows manual for instructions.)
3. If necessary, check your video card settings and set the multiple display option to Clone,Mirror, or
Duplicate.
Parent topic: Solutions When "No Signal" Message Appears
264
Displaying From a Mac Laptop
If you see the "No Signal" message when you display from a Mac laptop, you need to set up the laptop
for mirrored display. (See your laptop manual for details.)
1. Open the System Preferences utility and select Displays,Display, or Color LCD.
2. Click the Arrange or Arrangement tab.
3. Select the Mirror Displays checkbox.
Parent topic: Solutions When "No Signal" Message Appears
Solutions When "Not Supported" Message Appears
If the "Not Supported" message appears, try the following solutions:
• Make sure the correct input signal is selected on the Signal menu.
• Make sure the computer's display resolution does not exceed the projector's resolution and frequency
limit. If necessary, select a different display resolution for your computer. (See your computer manual
for details.)
• As a test, try setting the computer's display resolution to the lowest possible setting, and then
gradually increase it as necessary.
• Check the input resolution under Projector Info in the Info menu and make sure that the projector
supports that resolution.
Parent topic: Solving Image Problems
Related references
Input Signal Settings - Signal Menu
Supported Video Display Formats
Projector Information Display - Info Menu
Solutions When Only a Partial Image Appears
If only a partial computer image appears, try the following solutions:
• Press the Auto button on the remote control to optimize the image signal.
• Make sure you selected the correct Screen Type setting for the screen you are using.
• Make sure the Scale setting in the Extended menu is turned off.
• Try adjusting the image position using the Position setting in the Signal menu.
• Try adjusting the image position using the Screen Position menu setting.
265
• Press the Aspect button on the remote control to select a different image aspect ratio.
• Check the Blanking setting in the Signal menu.
• Check the cables connecting the computer or video source to the projector. Try connecting different
cables.
• Check your computer display settings to disable dual display and set the resolution within the
projector's limits. (See your computer manual for details.)
• Check the resolution assigned to your presentation files to see if they are created for a different
resolution than you are projecting in. (See your software help for details.)
• Make sure you selected the correct Projection setting in the Extended menu.
• If the other solutions do not solve the problem, reset all of the projector settings using the options on
the Reset menu.
Parent topic: Solving Image Problems
Related concepts
Projector Connections
Related references
Input Signal Settings - Signal Menu
Projector Reset Options - Reset Menu
Projector Setup Settings - Extended Menu
Related tasks
Setting the Screen Type
Scaling an Image
Adjusting the Image Position Using Screen Position
Changing the Image Aspect Ratio
Solutions When the Image is Not Rectangular
If the projected image is not evenly rectangular, try the following solutions:
• Place the projector directly in front of the center of the screen, facing it squarely, if possible.
• Adjust the image shape using the Geometry Correction menu settings.
Parent topic: Solving Image Problems
Related references
Projector Feature Settings - Settings Menu
266
Solutions When the Image Contains Noise or Static
If the projected image seems to contain electronic interference (noise) or static, try the following
solutions:
• Check the cables connecting your computer or video source to the projector. They should be:
• Separated from the power cord to prevent interference
• Securely connected at both ends
• Not connected to an extension cable
• No longer than 9.8 feet (3 m) for VGA/computer cables or 24 feet (7.3 m) for HDMI cables
• Select a computer video resolution and refresh rate that are compatible with the projector.
• If you are projecting from a computer, press the Auto button on the remote control to automatically
adjust the tracking and sync. If the problem remains, display a uniformly patterned image on the
screen and manually adjust the Tracking and Sync settings.
• Try a different cable.
• Try adjusting the Image Enhancement settings on the Image menu.
Parent topic: Solving Image Problems
Related references
Supported Video Display Formats
Image Quality Settings - Image Menu
Solutions When the Image is Fuzzy or Blurry
If the projected image is fuzzy or blurry, try the following solutions:
• Adjust the image focus.
• Clean the projector lens.
Note: To avoid condensation on the lens after bringing the projector in from a cold environment, let the
projector warm up to room temperature before using it.
• Position the projector close enough to the screen.
• Position the projector so the keystone adjustment angle is not so wide that it distorts the image.
• Adjust the Sharpness setting to improve image quality.
267
• If you are projecting from a computer, press the Auto button on the remote control to automatically
adjust the tracking and sync. If any bands or overall blurriness remain, display a uniformly patterned
image on the screen and manually adjust the Tracking and Sync settings.
• If you are projecting from a computer, try using a lower resolution or try to match the projector's native
resolution.
Parent topic: Solving Image Problems
Related references
Image Quality Settings - Image Menu
General Projector Specifications
Supported Video Display Formats
Related tasks
Focusing the Image Using the Focus and Distortion Buttons
Cleaning the Lens
Solutions When the Image Brightness or Colors are Incorrect
If the projected image is too dark or light, or the colors are incorrect, try the following solutions:
• Press the Color Mode button on the remote control to try different color modes for the image and
environment.
• Check your video source settings.
• Adjust the available settings on the Image menu for the current input source, such as Brightness,
Contrast,Tint,Advanced, and Color Saturation.
• Make sure you selected the correct Input Signal,Video Range,HDR 10 Setting, and HLG Setting
options on the Signal menu.
• Make sure you selected the correct Gamma or RGBCMY setting in the Image menu.
• Make sure all the cables are securely connected to the projector and your video device. If you
connected long cables, try connecting shorter cables.
• Make sure the Brightness Settings options in the Settings menu are set correctly.
• Position the projector close enough to the screen.
• When using multiple projectors, make sure Light Source Calibration in the Reset menu is set
correctly in all of the projectors. If light source calibration is performed only in some of the projectors,
the white balance and the brightness level of the projected image may differ between the projectors.
• If the above solutions do not correct your image, try resetting all of the projector's settings using the
Reset menu.
268
Parent topic: Solving Image Problems
Related references
Input Signal Settings - Signal Menu
Image Quality Settings - Image Menu
Projector Feature Settings - Settings Menu
Projector Reset Options - Reset Menu
Related tasks
Changing the Color Mode
Running Light Source Calibration
Solutions When Automatic Adjustments are not Applied Correctly
If you have problems with automatic adjustments not being applied correctly, try the following solutions:
• Be sure to wait at least 30 minutes after turning on the projector or turning off the Shutter setting
before performing automatic adjustments. This gives the projector's temperature a chance to stabilize.
• Check that the protective plate is not installed on the built-in camera and that the camera area is
clean.
• Depending on the lens you installed, automatic adjustments may not be available. If you installed one
of these lenses, you cannot use the Screen Matching setting or the Tiling Assist feature in the Epson
Projector Professional Tool software: ELPLX02, ELPLX02W, ELPLU04, or ELPLL08. If you installed
one of these lenses, you cannot use the Color Calibration setting: ELPLX02, ELPLX02W, or
ELPLL08.
• If you are projecting from an analog input source, the changing color and brightness of the image may
cause automatic adjustments to not be applied correctly.
• Make sure that a powerful spotlight or source of strong natural light is not shining into the projection
environment and interfering with automatic adjustments.
• Check that your image correction and image blending settings are within reasonable ranges. If the
projection angle is very large, try turning off the Geometry Correction setting or reduce the projection
angle. If you are using the Edge Blending setting, make sure the blending width is between 15 to
43%.
• If you see an error message during automatic adjustments, make a note of the error codes and
contact Epson for support.
Parent topic: Solving Image Problems
269
Related references
Projector Parts - Front/Top
Projector Parts - Side/Rear
Additional Projector Software and Manuals
Optional Equipment and Replacement Parts
Projector Feature Settings - Settings Menu
Where to Get Help
Related tasks
Shutting Off the Picture Temporarily
Cleaning the Projector Case
Running Light Source Calibration
Blending the Image Edges
Related topics
Matching Tint and Brightness (Screen Matching)
Solving Projector or Remote Control Operation Problems
Check the solutions in these sections if you have problems operating the projector or remote control.
Solutions to Projector Power or Shut-Off Problems
Solutions to Remote Control Problems
Solutions to Password Problems
Parent topic: Solving Problems
Solutions to Projector Power or Shut-Off Problems
If the projector does not come on when you press the power button or it shuts off unexpectedly, try the
following solutions:
• Make sure the power cord is securely connected to the projector and to a working electrical outlet.
• The projector's buttons may be locked for security. Unlock the buttons or use the remote control to
turn on the projector.
• Make sure the power switch is turned on.
• If the projector's laser shuts off unexpectedly, it may have entered standby mode after a period of
inactivity. Press the power button to wake the projector and adjust the Sleep Mode setting to change
the sleep interval.
270
• If the power button on the remote control does not turn on the projector, check its batteries and make
sure the Remote Receiver setting is turned on in the projector's menu, if available.
• If the power button on the remote control does not turn on the projector, check its batteries.
• If you have set the remote control to operating only a projector with a matching ID, set the ID switch to
Off.
• If the projector lights turn on and off when you touch the power cord, the cord may have a poor contact
with the electrical outlet. Unplug the power cord and plug it back in to check.
• The power cord may be defective. Try another power cord. If that doesn't work, disconnect the cord
and contact Epson.
• If you see an error message indicating that the battery for your clock settings is running low, contact
Epson for support.
• If you do not see error messages or other information displayed after turning on the projector, a
sudden voltage drop, blackout, or power cut may have occurred. Turn off the power switch or unplug
the power cord, wait at least 10 seconds, then turn on the power switch or plug in the power cord.
Parent topic: Solving Projector or Remote Control Operation Problems
Related references
Projector Setup Settings - Extended Menu
Where to Get Help
Related tasks
Turning On the Projector
Turning Off the Projector
Unlocking the Projector's Buttons
Replacing the Remote Control Batteries
Setting the Remote Control ID
Solutions to Remote Control Problems
If the projector does not respond to remote control commands, try the following solutions:
• Check that the remote control batteries are installed correctly and have power. If necessary, replace
the batteries.
• Make sure you are operating the remote control within the reception angle and range of the projector.
• Make sure the projector is not warming up or shutting down.
• Check to see if a button on the remote control is stuck down, causing it to enter sleep mode. Release
the button to wake the remote control up.
271
• If you enabled the remote control button lock, press and hold the ibutton for about 5 seconds to turn it
off.
• Strong fluorescent lighting, direct sunlight, or infrared device signals may be interfering with the
projector's remote receivers. Dim the lights or move the projector away from the sun or interfering
equipment.
• Make sure the optional remote control cable set is not attached to the projector's Remote port. If you
leave the cable connected to the port, the remote control cannot control the projector.
• If available, turn on one of the remote receivers in the projector's menu system, or check if all the
remote receivers were turned off.
• If you assigned an ID number to the remote control to operate multiple projectors, you may need to
check or change the ID setting (feature not available with all projectors).
• Make sure the Control Communications or Extron XTP setting in the Extended menu is set to Off if
you are using the optional remote control cable set.
• If you lose the remote control, you can purchase another from an authorized Epson reseller.
Parent topic: Solving Projector or Remote Control Operation Problems
Related references
Remote Control Operation
Projector Parts - Interface Ports
Projector Feature Settings - Settings Menu
Projector Setup Settings - Extended Menu
Related tasks
Replacing the Remote Control Batteries
Locking the Remote Control Buttons
Unlocking the Projector's Buttons
Setting the Remote Control ID
Solutions to Password Problems
If you cannot enter or remember a password, try the following solutions:
• You may have turned on password protection without first setting a password. Try entering 0000 using
the remote control.
• If you have entered an incorrect password too many times and see a message displaying a request
code, write down the code and contact Epson. Do not attempt to enter the password again. Provide
the request code and proof of ownership for assistance in unlocking the projector.
272
• If you set a Epson Web Control password and forgot the user ID or password, try entering the
following:
• User ID: EPSONWEB
• Default password: admin
• If you set a Remote password (in Epson Web Control) and forgot the user ID or password, try entering
the following:
• User ID: EPSONREMOTE
• Default password: guest
• If you lose the remote control, you cannot enter a password. Order a new one from Epson.
Parent topic: Solving Projector or Remote Control Operation Problems
Related concepts
Password Security Types
Solving Network Problems
Check the solutions in these sections if you have problems using the projector on a network.
Solutions When Wireless Authentication Fails
Solutions When You Cannot Access the Projector Through the Web
Solutions When the Image Contains Static During Network Projection
Solutions When Network Alert E-Mails are Not Received
Parent topic: Solving Problems
Solutions When Wireless Authentication Fails
If you cannot authenticate a wireless connection, try the following solutions:
• If the wireless settings are correct, but authentication fails, you may need to update the Date & Time
settings in the Extended menu, if available.
• Make sure the Wireless Mode setting is set to Wireless LAN On.
• Check the Security settings and passphrase in the Network Configuration menu.
• Check the Event ID number displayed in the Info menu and check the link below to identify the
problem.
• Make sure the connected device is on and operating properly.
Parent topic: Solving Network Problems
273
Related references
Projector Setup Settings - Extended Menu
Event ID Code List
Related tasks
Selecting Wireless Network Settings Manually
Setting Up Wireless Network Security
Solutions When You Cannot Access the Projector Through the Web
If you are unable to access the projector through a web browser, make sure you are using the correct ID
and password, which are case sensitive.
• For the user ID, enter EPSONWEB. (You cannot change the user ID.)
• For the password, enter the password set in the projector's Network menu. The default password is
admin.
• Make sure you have access to the network the projector is on.
• If you have problems while controlling the projector using Art-Net, any operations you perform using
the projector remote control or control panel may cause your software operations to be applied
incorrectly. To apply channel controls to the projector, set Channel 13 to Cannot control, then set it
back to Can control.
Note: The user ID and password are case sensitive.
Parent topic: Solving Network Problems
Related concepts
Password Security Types
Related references
Art-Net Channel Definitions
Related tasks
Controlling a Networked Projector Using a Web Browser
274
Solutions When the Image Contains Static During Network Projection
If the projected image contains static during network projection, try the following solutions:
• Check for any obstacles between the access point, the computer, the mobile device, and the projector.
If necessary, change their positions to improve communication. Also make sure that they are not too
far apart; move them closer together and try to connect again.
• If the wireless connection is slow or your projected image contains noise, check for interference from
other equipment, such as a Bluetooth device or microwave. Move the interfering device farther away
or expand your wireless bandwidth.
• If the connection speed declines, reduce the number of connected devices.
Parent topic: Solving Network Problems
Solutions When Network Alert E-Mails are Not Received
If you do not receive an e-mail alerting you to problems with a projector over the network, try the
following solutions:
• Make sure the projector is turned on and connected to the network correctly. (If an error shut down the
projector, it cannot send an e-mail.)
• Make sure you set up the projector e-mail alert settings correctly on the projector's network
Notifications menu or in the network software.
• Set the Standby Mode setting to Communication On so the network software can monitor the
projector in standby mode.
Parent topic: Solving Network Problems
Related references
Projector Setup Settings - Extended Menu
Related tasks
Setting Up Projector Network E-Mail Alerts
Where to Get Help
If you need to contact Epson for technical support services, use the following support options.
Internet Support
Visit Epson's support website at epson.com/support (U.S.), epson.ca/support (Canada), or
epson.com.jm/support (Caribbean) and select your product for solutions to common problems with your
275
projector. You can download utilities and documentation, get FAQs and troubleshooting advice, or e-mail
Epson with your questions.
Speak to a Support Representative
To use the Epson PrivateLine Support service, call (800) 637-7661. This service is available for the
duration of your warranty period. You may also speak with a projector support specialist by dialing (562)
276-4394 (U.S.) or (905) 709-3839 (Canada).
Support hours are 6 AM to 8 PM, Pacific Time, Monday through Friday and 7 AM to 4 PM, Pacific Time,
Saturday.
Days and hours of support are subject to change without notice. Toll or long distance charges may
apply.
Before you call, have the following information ready:
• Product name
• Product serial number (located on the bottom or rear of the projector, or in the menu system)
• Proof of purchase (such as a store receipt) and date of purchase
• Computer or video configuration
• Description of the problem
Purchase Supplies and Accessories
You can purchase screens, other optional accessories, and replacement parts from an Epson authorized
reseller. To find the nearest reseller, call 800-GO-EPSON (800-463-7766) in the U.S. or 800-807-7766 in
Canada. Or you can purchase online at epsonstore.com (U.S. sales) or epsonstore.ca (Canadian sales).
To purchase a replacement remote control, call (562) 276-4394 (U.S.) or (905) 709-3839 (for dealer
referral in Canada).
Parent topic: Solving Problems
276
Technical Specifications
These sections list the technical specifications of your projector.
General Projector Specifications
Projector Light Source Specifications
Remote Control Specifications
Projector Dimension Specifications
Projector Electrical Specifications
Projector Environmental Specifications
Projector Safety and Approvals Specifications
Safety and Approvals Specifications for Latin America
Supported Video Display Formats
General Projector Specifications
Type of display Poly-silicon TFT active matrix
Resolution 1920 × 1200 pixels (WUXGA)
Lens F=1.8 to 2.3
Focal length: 36.0 to 57.3 mm
Color reproduction Up to 1.07 billion colors
Brightness Normal Power Consumption mode:
White light output 20000 lumens (ISO 21118 standard)
Color light output 20000 lumens
Quiet/Extended Power Consumption mode:
White light output 14000 lumens (ISO 21118 standard)
Note: Color brightness (color light output) and white brightness
(white light output) will vary depending on usage conditions. Color
light output measured in accordance with IDMS 15.4; white light
output measured in accordance with ISO 21118.
Contrast ratio Over 2,500,000:1 (dynamic on), 2000:1 (native)
277
Image size
(in native aspect ratio)
60 inches (1.52 m) to 1000 inches (25.4 m)
Projection distance
(in native aspect ratio)
78.3 inches (1.99 m) to 2190.2 inches (55.63 m)
Projection methods Front, rear, ceiling-mounted
Optical aspect ratio
(width-to-height)
16:10
Focus adjustment Powered
Zoom adjustment Powered
Zoom ratio
(Tele-to-Wide)
1:1.61
Noise level 45 dB (Normal Power Consumption mode)
38 dB (Quiet Power Consumption mode)
Keystone correction angle ± 44º vertical (manual)
± 30° horizontal (manual)
USB Type B port compatibility USB 1.1 and 2.0 compliant for firmware update or copying menu
settings
USB Type A port compatibility One USB 1.1 and 2.0 compliant port for firmware update or copying
menu settings, or for use as a DC Out 900mA port on HDMI/DVI-D
interface board
Parent topic: Technical Specifications
Projector Light Source Specifications
Type Laser diode
Light source output power Up to 488 W
Wavelength 450 to 460 nm
278
Light source life
(approximate)
Normal/Quiet Light Source Mode:
Up to about 20000 hours
Extended Light Source Mode:
Up to about 43000 hours
Note: Turn off this product when not in use to prolong the life of the projector. Laser life will vary
depending upon mode selected, environmental conditions, and usage. Brightness decreases over time.
Parent topic: Technical Specifications
Remote Control Specifications
Reception range 98.4 feet (30 m)
Batteries Two alkaline or manganese AA
Parent topic: Technical Specifications
Projector Dimension Specifications
Height (excluding feet) 11.02 inches (280 mm)
Width 24.4 inches (620 mm)
Depth 28.3 inches (720 mm)
Weight Pro L20000UNL:
109.3 lb (49.6 kg)
Pro L20002UNL:
110.9 lb (50.3 kg)
Parent topic: Technical Specifications
Projector Electrical Specifications
Rated frequency 50/60 Hz
279
Power supply 110 to 120 V AC ±10% :
12.0 A
220 to 240 V AC ±10% :
9.7 A
Note: 110 to 120 V AC power is for service purposes; use 220 to
240 V AC power for normal operation.
Power consumption
(110 to 120 V)
Operating:
Normal Power Consumption mode: 1178 W
Standby:
0.5 W (Communication Off), 2 W (Communication On)
Note: 110 to 120 V AC power is for service purposes; use 220 to
240 V AC power for normal operation.
Power consumption
(220 to 240 V)
Operating:
Normal Power Consumption mode: 1860 W
Standby:
0.5 W (Communication Off), 2 W (Communication On)
Parent topic: Technical Specifications
Projector Environmental Specifications
Temperature Operating:
Up to 4921 feet (1500 m): 32 to 122 °F (0 to 50 °C)
4921 feet (1500 m) to 10000 feet (3048 m): 32 to 113 °F (0 to 45 °C)
Storage: 14 to 140 °F (–10 to 60 °C)
Humidity (relative, non-
condensing)
Operating: 20 to 80%
Storage: 10 to 90%
Operating altitude Up to 4921 feet (1500 m)
Up to 10000 feet (3048 m) with High Altitude Mode enabled
280
Parent topic: Technical Specifications
Related references
Projector Setup Settings - Extended Menu
Projector Safety and Approvals Specifications
United States FCC Part 15B Class A (DoC)
UL60950-1 2nd edition/UL62368-1 2nd edition (cTUVus Mark)
Canada ICES-003 Class A
CSA C22.2 No. 60950-1-07/CSA C22.2 No. 62368-1-14 (cTUVus
Mark)
Parent topic: Technical Specifications
Safety and Approvals Specifications for Latin America
Notice for Argentina
WLAN Module Model: WLU5000-D101 (RoHS)
Brand: EPSON
CNC ID: C16265
Notice for Mexico
Operation is subject to the following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference that may cause
undesired operation of the device.
WLAN Module Model: WLU5000-D101 (RoHS)
Brand: EPSON
IFT Certification Number: RCPEPWL16-0829
Notice for Paraguay
Imported by:
Fastrax, S.A.
281
Av. Perú esq. Río de Janeiro, Barrios Las Mercedes, Asunción, Paraguay
Imported by:
Sol Control S.R.L.
Av. Gral. Bernardino Caballero 810 esq. Celsa Speratti, Asunción, Paraguay
Notice for Peru
Product Manufacturer: Seiko Epson Corporation
Address: 3-3-5 Owa Suwa-shi, Nagano-Ken 392-8502, Japan
Brand: EPSON
Product Model: Pro L20000UNL/L20002UNL
This product uses the following network module:
WLAN Module Model: WLU5000-D101 (RoHS)
FCC ID: BKMAE-WLU5000
Parent topic: Technical Specifications
Supported Video Display Formats
For best results, your computer's monitor port or video card resolution should be set to display in the
projector's native resolution. However, your projector includes Epson's SizeWise chip that supports other
computer display resolutions, so your image will be resized to fit automatically.
Your computer's monitor port or video card refresh rate (vertical frequency) must be compatible with the
projector. (See your computer or video card manual for details.)
The table here lists the compatible refresh rate and resolution for each compatible video display format.
Display format Refresh rate (in Hz) Resolution (in pixels)
Computer signals (analog RGB)
VGA 60/72/75/85 640 × 480
SVGA 60/72/75/85 800 × 600
XGA 60/70/75/85 1024 × 768
282
Display format Refresh rate (in Hz) Resolution (in pixels)
WXGA 60 1280 × 768
60/75/85 1280 × 800
60 1366 × 768
WXGA+ 60/75/85 1440 × 900
WXGA++ 60 1600 × 900
SXGA 70/75/85 1152 × 864
60/75/85 1280 × 960
60/75/85 1280 × 1024
SXGA+ 60/75 1400 × 1050
WSXGA+160 1680 × 1050
UXGA 60 1600 × 1200
1920 × 1080 50/60 1920 × 1080
WUXGA260 1920 × 1200
SDTV (480p) 59.94 720 × 480
SDTV (576p) 50 720 × 576
HDTV (720p) 50/59.94/60 1280 × 720
HDTV (1080p) 50/59.94/60 1920 × 1080
Component video
SDTV (480i/480p) 59.94 720 × 480
SDTV (576i/576p) 50 720 × 576
HDTV (720p) 50/59.94/60 1280 × 720
HDTV (1080i) 50/59.94/60 1920 × 1080
DVI-D, HDMI, and HDBaseT input signals
VGA 60 640 × 480
SVGA 60 800 × 600
XGA 60 1024 × 768
283
Display format Refresh rate (in Hz) Resolution (in pixels)
WXGA 60 1280 × 800
60 1366 × 768
WXGA+ 60 1440 × 900
WXGA++ 60 1600 × 900
WSXGA+ 60 1680 × 1050
SXGA 60 1280 × 960
60 1280 × 1024
SXGA+ 60 1400 × 1050
UXGA 60 1600 × 1200
1920 × 1080 50/60 1920 × 1080
WUXGA260 1920 × 1200
QXGA360 2048 × 1536
WQHD360 2560 × 1440
WQXGA2, 3 60 2560 × 1600
SDTV (480i/480p) 59.94 720 × 480
SDTV (576i/576p) 50 720 × 576
HDTV (720p) 50/59.94/60 1280 × 720
HDTV (1080i) 50/59.94/60 1920 × 1080
HDTV (1080p)323.98/24/29.97/30/50/59.94/60 1920 × 1080
4K×2K2, 3 23.98/24/25/29.97/30 3840 × 2160
4K×2K350/59.94/60 3840 × 2160
4K×2K (SMPTE)2, 3 23.98/24 4096 × 2160
4K×2K (SMPTE)350/59.94/60 4096 × 2160
SDI input signals (all 10 bit)
SDTV (480i) 59.94 (SD-SDI mode4) 720 × 480
SDTV (576i) 50 (SD-SDI mode4) 720 × 576
284
Display format Refresh rate (in Hz) Resolution (in pixels)
HDTV (720p) 50/59.94/60 (HD-SDI mode4) 1280 × 720
HDTV (1080i) 50/59.94/60 (HD-SDI mode4) 1920 × 1080
HDTV (1080p) 23.98/24/25/29.97/30 (HD-SDI
mode4)
1920 × 1080
HDTV (1080p)650/59.94/60 (3G-SDI mode;
Level A4)
1920 × 1080
HDTV (1080p)623.98/24/25/29.97/30 (3G-SDI
mode; Level A5)
1920 × 1080
HDTV (1080i) 50/59.94/60 (3G-SDI mode;
Level A5)
1920 × 1080
1Compatible only when Wide is selected as the Resolution setting
2Compatible only with VESA CVT-RB (Reduced Blanking) input signal
3HDMI or HDBaseT input only
4Compatible with YPbPr 4:2:2 input signals
5Compatible with RGB4:4:4 input signals
6Supports HDR (HDR10 and HLG)
Parent topic: Technical Specifications
Related references
Input Signal Settings - Signal Menu
285
Notices
Check these sections for important notices about your projector.
Recycling
Important Safety Information
Important Safety Instructions
List of Safety Symbols (corresponding to IEC60950-1 A2)
Manufacturer and Importer Address
FCC Compliance Statement
Binding Arbitration and Class Waiver
Trademarks
Copyright Notice
Recycling
Epson offers a recycling program for end of life products. Please go to this site for information on how to
return your products for proper disposal.
Parent topic: Notices
Important Safety Information
Caution: Never look into the projector lens when the laser is turned on; the bright light can damage your
eyes. Never let children look into the lens when it is on. Never open any cover on the projector, except
the filter covers. Dangerous electrical voltages inside the projector can severely injure you. Except as
specifically explained in this User's Guide, do not attempt to service this product yourself. Refer all
servicing to qualified service personnel.
Warning: The projector and its accessories come packaged in plastic bags. Keep plastic bags away
from small children to avoid any risk of suffocation.
Parent topic: Notices
Important Safety Instructions
Follow these safety instructions to avoid damage to the product and serious or fatal bodily injury:
286
Setup and operation
• If an error occurs in the projector, turn off the power and unplug the projector immediately. Continuing
to use the projector could result in an electric shock, fire, or visual impairment. Contact Epson support.
• Use of controls or adjustments or performance of procedures other than those specified herein may
result in hazardous radiation exposure.
• The projector and its accessories come packaged in plastic bags. Keep plastic bags away from small
children to avoid any risk of suffocation.
• Do not look into the lens when the projector is on. The bright light can damage your eyes. Avoid
standing in front of the projector so the bright light does not shine into your eyes.
• Possibly hazardous optical radiation emitted from this product. Do not direct or reflect the laser light
toward people or reflective objects. Do not look at the operating light source or expose your skin to it.
Eye and/or skin injury may result if these instructions are not followed.
• Do not look into the lens using optical devices, such as a magnifying glass or telescope. This could
cause visual impairment.
• Do not apply optical devices, such as a magnifying glass or reflector, to the projected image. Using the
projector in this way may result in physical harm, fire, or an accident.
• When turning on the projector at a distance using the remote control, make sure no one is looking into
the lens.
• Do not place the projector where the cord can be walked on. This may result in fraying or damage to
the plug.
• Do not operate the projector in a closed-in cabinet unless proper ventilation is provided.
• Do not block the slots and openings in the projector case. They provide ventilation and prevent the
projector from overheating. Do not operate the projector on a sofa, rug, or other soft surface, or set it
on top of loose papers. Do not cover the projector with a blanket, curtain, or tablecloth. If you are
setting up the projector near a wall, leave at least 7.9 inches (20 cm) of space between the wall and
the projector.
• Do not allow small children to operate the projector. Children must be accompanied by an adult.
• Before using the projector, make sure there is nothing in the area that could reflect the projected
image.
• If the projector is mounted on a ceiling or wall, it should be installed by qualified technicians using
mounting hardware designed for use with this projector.
• When installing or adjusting a ceiling or wall mount, do not use adhesives to prevent the screws from
loosening and do not use oils or lubricants. This may cause the projector case to crack and the
287
projector to fall from its ceiling mount. This could cause serious injury to anyone under the mount and
could damage the projector.
• Do not use the projector near water, sources of heat, high-voltage electrical wires, or sources of
magnetic fields.
• Use the type of power source indicated on the projector. Use of a different power source may result in
fire or electric shock. If you are not sure of the power available, consult your dealer or power company.
• Place the projector near a wall outlet where the plug can be easily unplugged.
• Take the following precautions when handling the plug: Do not hold the plug with wet hands. Do not
insert the plug into a dusty outlet. Insert the plug firmly into the outlet. Do not pull the power cord when
disconnecting the plug; always be sure to hold the plug when disconnecting it. Do not overload wall
outlets, extension cords, or power strips. Failure to comply with these precautions could result in fire or
electric shock.
• Never allow objects of any kind to enter any openings in the projector. Do not leave objects, especially
flammable objects, near the projector. Never spill liquid of any kind into the projector.
• Never open any covers on the projector except as specifically explained in this manual. Never attempt
to disassemble or modify the projector. Refer all repairs to qualified service personnel.
• Unplug the projector from the wall outlet and refer servicing to qualified service personnel under the
following conditions: if it does not operate normally when you follow the operating instructions, or
exhibits a distinct change in performance; if smoke, strange odors, or strange noises come from the
projector; if the power cord or plug is damaged or frayed; if liquid or foreign objects get inside the
projector, or if it has been exposed to rain or water; if it has been dropped or the housing has been
damaged.
• Place the projector near a wall outlet where the plug can be easily unplugged.
• Do not touch the plug during an electrical storm. Otherwise, you may receive an electric shock.
• Do not use the projector where it may be exposed to rain, water, or excessive humidity.
• Do not use the projector where flammable or explosive gases may be present.
• Do not use or store the projector or remote control in a hot location, such as near a heater, in direct
sunlight, or in a closed vehicle.
• Do not place the source of an open flame, such as a lit candle, on or near the projector.
• Do not block the lens during projection using a book or any other object. This could damage the
projector or cause a fire.
• Do not modify the power cord. Do not place heavy objects on top of the power cord or bend, twist, or
pull it excessively. Keep the power cord away from hot electrical appliances.
288
• Always attach the lens cover to the lens when not using the projector to prevent the lens from
becoming dirty or damaged.
• If you use the projector in a country other than where you purchased it, use the correct power cord for
that country.
• Do not stand on the projector or place heavy objects on it.
• Do not use the projector outside of the required temperature range below:
32 to 122 °F (0 to 50 °C) at an altitude of 4921 feet (1500 m) or less, and 32 to 113 °F (0 to 45 °C) at
an altitude of 4925 to 10000 feet (1501 to 3048 m)
Doing so may cause an unstable display and could lead to projector damage. Do not use or store the
projector where it may be exposed to sudden changes in temperature.
• Do not place anything that can become warped or damaged by heat near the exhaust vents. Do not
bring your hands or face close to the vents while projection is in progress. Do not bring your face close
to the projector while it is in use.
• Do not place the projector on an unstable cart, stand, or table.
Maintenance, storage, and transportation
• Unplug the projector from the wall outlet and allow to cool before cleaning. Use a dry cloth (or, for
stubborn dirt or stains, a moist cloth that has been wrung dry) for cleaning. Do not use liquid or aerosol
cleaners, any sprays containing flammable gas, or solvents such as alcohol, paint thinner, or benzine.
• Do not open the projector's case. The projector contains a high-powered laser.
• Unplug the projector from the wall outlet and allow to cool before cleaning. Use a dry cloth (or, for
stubborn dirt or stains, a moist cloth that has been wrung dry) for cleaning. Do not use liquid or aerosol
cleaners, any sprays containing flammable gas, or solvents such as alcohol, paint thinner, or benzine.
• Do not attempt to disassemble or modify the projector. The projector contains a high-power laser
component. Serious injury could result.
• You may need to clean the air filter and vent. A clogged air filter or vent can block ventilation needed
to cool the projector. Do not use canned air, or the gases may leave a residue.
• Do not store the projector outdoors for an extended length of time.
• Do not use or store the projector where it may be exposed to smoke, steam, corrosive gases,
excessive dust, vibration, or shock.
• Unplug the projector when it will not be used for extended periods.
• Do not store the projector outside of the required temperature range of 14 to 140 °F (–10 to 60 °C) or
in direct sunlight for long periods of time. Doing so may cause damage to the case.
289
• Before you move the projector, make sure its power is turned off, the plug is disconnected from the
outlet, and all cables are disconnected.
• When disposing of the projector, do not disassemble it. Dispose of the projector in accordance with
your local or national laws and regulations.
Laser Safety Information
Laser Safety Labels
Hazard Distance (HD)
Typical Setup Configurations (U.S. Only)
Parent topic: Notices
Laser Safety Information
This projector is a Class 1/RG3 laser product that complies with the IEC60825-1 international standard
for lasers. This projector contains a high-powered laser component and the following precautions should
be taken when operating the projector to avoid injury or damage:
• Do not enter the exclusion zone that is determined by the light beam Hazard Distance (HD). See the
link below for hazard distance information.
• Never open any covers on the projector except as specifically explained in this manual. Never attempt
to disassemble or modify the projector.
• All installations and repairs of this projector must be done by a licensed service personnel.
• The projector generates high amounts of heat. Do not place flammable or combustible objects around
the projector, especially in front of the lens.
Note: See the link below for additional safety laser cautions and other general safety instructions.
Parent topic: Important Safety Instructions
Related references
Laser Safety Labels
Hazard Distance (HD)
Typical Setup Configurations (U.S. Only)
Laser Safety Labels
Labels are attached to the projector to indicate the level of risk when operating or servicing the projector.
290
This product is in conformity with performance standards for laser products under 21CFR 1040, except
with respect to those characteristics authorized by Variance Number 2018-V-3295 effective on
November 21, 2018.
Certification labels (located on side of projector)
WARNING
RISK GROUP 3: IEC 62471:2006/LIPs Guidance dated Feb. 18, 2015
Possibly hazards optical radiation emitted from this product.
291
Comply with 21 CFR Part 1040 except with respect to those characteristics authorized by VARIANCE
NUMBER 2018-V-3295 Dated November 21, 2018
WARNING: Do not look into the beam. No direct eye exposure to the beam is permitted.
RG3 IEC/EN62471-5:2015, CLASS 1 LASER PRODUCT IEC/EN60825-1:2014
Hazard Distance: Refer to the manual.
292
Manufacturer identification label (located on back of projector)
WARNING: Never open any covers on the projector expect as specifically explained in the projector
manual.
Dangerous electrical voltages inside the projector can severely injure you.
293
Protective housing label (located inside of projector)
CAUTION/DANGER: CLASS 4 LASER RADIATION WHEN OPEN
AVOID EYE OR SKIN EXPOSURE TO DIRECT OR SCATTERED RADIATION
Parent topic: Important Safety Instructions
Hazard Distance (HD)
Hazard Distance (HD) is the distance measured from the projection lens at which the intensity of the
energy per surface unit becomes lower than the applicable exposure limit on the cornea or on the skin.
To prevent risk of eye or skin exposure, no person should enter the area within the HD of the projector
during operation.
294
The HD depends on the number of lumens produced by the projector, the size of the panel(s) used, and
the type of lens installed. HD values are provided in the table below.
To protect untrained end users (such as cinema visitors or spectators), the installation shall comply with
the following installation requirements: Operators shall control access to the beam within the hazard
distance or install the product at the height that will prevent spectators from being in the hazard distance.
Radiation levels in excess of the limits will not be permitted at any point less than 2.0 meters (SH) above
any surface upon which persons other than operators, performers, or employees are permitted to stand
or less than 1.0 meter (SH) lateral separation from any place where such persons are permitted to be. In
environments where unrestrained behavior is reasonably foreseeable, the minimum separation height
should be greater than or equal to 3.0 meters to prevent potential exposure, for example by an individual
sitting on another individual’s shoulders, within the HD.
295
These values are minimum values and are based on the guidance provided in IEC 62471-5:2015 section
6.6.5.
The installer must understand the risk and apply protective measures based upon the hazard distance
as indicated on the label and in the user information. Installation method, separation height, barriers,
detection systems or other applicable control measures shall prevent spectator access to the projected
light within the hazard distance.
For example, projectors that have a HD greater than 1 meter and emit light into an uncontrolled area
where persons may be present should be positioned in accordance with “the fixed projector installation”
parameters, resulting in a HD that does not extend into the audience area unless the beam is at least 2.0
meters above the floor level. In environments where unrestrained behavior is reasonably foreseeable,
the minimum separation height should be greater than or equal to 3.0 meters to prevent potential
exposure, for example by an individual sitting on another individual’s shoulders, within the HD.
Sufficiently large separation height may be achieved by mounting the image projector on the ceiling or
through the use of physical barriers.
U.S.A. Market Only:
This projector is a Class 1/RG3 laser product that complies with FDA Title 21 CFR 1040. This projector
can only be installed by qualified service personnel with an approved laser light show variance. Only
trained users with a valid laser light show variance are allowed access to the area where the projector is
installed. The area should be secured and access to it controlled by the owner of the location. Installers
must have a valid variance for production of Class IIIb and IV laser light shows and/or for incorporation of
the RG3 LIPs into their shows. Dealers, distributors, and end-users are also required to obtain a valid
laser light show variance.
If you are renting out this projector, it should only be delivered to parties that demonstrates that they
have a valid variance in effect at the time of delivery that permits them to produce laser light shows
incorporating this projector.
For a laser-illuminated projector (LIP) installed in the U.S.A. market, the following limits apply. For
installations other than in cinema theaters, an LIP shall be installed at a height vertically above the floor
such that the bottom plane of the hazard zone shall be no lower than 3.0 meters above the floor.
Horizontal clearance to the hazard zone shall be 2.5 meters. Any human access horizontally to the
hazard zone, if applicable, shall be restricted by barriers. If human access is possible in an unsupervised
environment, the horizontal or vertical clearances shall be increased to prevent exposure to the RG3
hazard zone.
Install one or more readily accessible controls to immediately terminate LIP projection light. The power
input at the projector side is considered as a reliable disconnect device. When required to switch off the
projector, disconnect the power cord at the projector side. In case the power input at the projector side is
not accessible (such as in a truss mount), the socket outlet supplying the projector shall be installed
nearby the projector and be easily accessible, or a readily accessible general disconnect device shall be
296
incorporated in the fixed wiring. Additionally, the projection light can be turned off by pressing the
Shutter button on the projector's control panel or remote control.
Parent topic: Important Safety Instructions
Typical Setup Configurations (U.S. Only)
Show - Elevation View
• Projector mounted from the ceiling.
• 9.8 ft (3 m) minimum vertical clearance from accessible floor to bottom plane of Hazard Zone.
• Hazard zone effectively isolated from human access with physical barriers and warning signage.
Note: Typical layout concept; not necessarily to scale.
Show - Elevation View - Typical Temporary Cinema Application
• Projector positioned at rear of venue.
• Front projection over audience onto projection surface.
• 8.2 ft (2.5 m) minimum lateral distance from accessible area to Hazard Zone.
• 9.8 ft (3 m) minimum vertical clearance from any accessible floor to bottom plane of Hazard Zone.
297
• Controlled Area** prevents human access with physical barriers and warning signage except
authorized personnel.
• Audience allowed only outside the controlled area.
Note: Typical layout concept; not necessarily to scale.
Show - Plan View - Typical Temporary Cinema Application
• Projector positioned at rear of venue.
• Front projection over audience onto projection surface.
• 8.2 ft (2.5 m) minimum lateral distance from accessible area to Hazard Zone.
• Controlled Area** prevents human access with physical barriers and warning signage except
authorized personnel.
298
• Audience allowed only outside the controlled area.
Note: Typical layout concept; not necessarily to scale.
Parent topic: Important Safety Instructions
List of Safety Symbols (corresponding to IEC60950-1 A2)
The following table lists the meaning of the safety symbols labeled on the equipment.
No. Symbol Approved Standards Description
1 IEC60417
No.5007
"ON" (power)
To indicate connection to the mains.
299
No. Symbol Approved Standards Description
2 IEC60417
No.5008
"OFF" (power)
To indicate disconnection from the
mains.
3 IEC60417
No.5009
Stand-by
To identify the switch or switch position
by means of which part of the equipment
is switched on in order to bring it into the
stand-by condition.
4 ISO7000
No.0434B
IEC3864-B3.1
Caution
To identify general caution when using
the product.
5 IEC60417
No.5041
Caution, hot surface
To indicate that the marked item can be
hot and should not be touched without
taking care.
6 IEC60417
No.6042
ISO3864-B3.6
Caution, risk of electric shock
To identify equipment that has risk of
electric shock.
7 IEC60417
No.5957
For indoor use only
To identify electrical equipment designed
primarily for indoor use.
8 IEC60417
No.5926
Polarity of DC power connector
To identify the positive and negative
connections (the polarity) on a piece of
equipment to which a DC power supply
may be connected.
300
No. Symbol Approved Standards Description
9 — Same as No. 8
10 IEC60417
No.5001B
Battery, general
On battery powered equipment. To
identify a device for instance a cover for
the battery compartment, or the
connector terminals.
11 IEC60417
No.5002
Positioning of cell
To identify the battery holder itself and to
identify the positioning of the cell(s)
inside the battery holder.
12 — Same as No. 11
13 IEC60417
No.5019
Protective earth
To identify any terminal which is intended
for connection to an external conductor
for protection against electric shock in
case of a fault, or the terminal of a
protective earth electrode.
14 IEC60417
No.5017
Earth
To identify an earth (ground) terminal in
cases where neither the symbol No.13 is
explicitly required.
15 IEC60417
No.5032
Alternating current
To indicate on the rating plate that the
equipment is suitable for alternating
current only; to identify relevant
terminals.
301
No. Symbol Approved Standards Description
16 IEC60417
No.5031
Direct current
To indicate on the rating plate that the
equipment is suitable for direct current
only; to identify relevant terminals.
17 IEC60417
No.5172
Class II equipment
To identify equipment meeting the safety
requirements specified for Class II
equipment according to IEC 61140.
18 ISO 3864 General prohibition
To identify actions or operations that are
prohibited.
19 ISO 3864 Contact prohibition
To indicate injury that could occur due to
touching a specific part of the equipment.
20 — Never look into the optical lens while the
projector is on.
21 — To indicate that the marked item don’t
place anything on projector.
22 ISO3864
IEC60825-1
Caution, laser radiation
To indicate the equipment has a laser
radiation part.
23 ISO 3864 Disassembly prohibition
To indicate a risk of injury, such as
electric shock, if the equipment is
disassembled.
302
No. Symbol Approved Standards Description
24 IEC60417
No. 5266
Standby, partial standby
To indicate that part of the equipment is
in the ready status.
25 ISO3864
IEC60417
No. 5057
Caution, movable parts
To indicate that you must keep away
from movable parts according to
protection standards.
26 IEC60417-6056 Caution (Moving Fan Blades)
To indicate that you must keep away
from moving fan blades.
27 IEC60417-6043 Caution (Sharp Corners)
To indicate that you must not touch sharp
corners.
28 — To indicate that looking into the lens
while projecting is prohibited.
29 ISO7010
No. W027
ISO3864
Warning, light emission (UV, visible light,
IR, etc.)
When you are close to the light
emissions, be careful not to injure your
eyes or skin.
30 IEC60417
No. 5109
Usage prohibition in residential areas
To indicate that this is an electrical device
or a device that is not suitable for use in
residential areas.
Parent topic: Notices
Manufacturer and Importer Address
Manufacturer
Name: Seiko Epson Corporation
303
Address: 3-5, Owa 3-chome, Suwa-shi, Nagano-ken 392-8502 Japan
Telephone: 81-266-52-3131
Importer
Name: Epson America, Inc.
Address: 3840 Kilroy Airport Way, Long Beach, CA 90806 U.S.A.
Telephone: (800) 463-7766
Parent topic: Notices
FCC Compliance Statement
For United States Users
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be required to correct
the interference at his own expense.
For Canadian Users
CAN ICES-3(A)/NMB-3(A)
Parent topic: Notices
Binding Arbitration and Class Waiver
1. DISPUTES, BINDING INDIVIDUAL ARBITRATION, AND WAIVER OF CLASS ACTIONS AND
CLASS ARBITRATIONS
1.1 Disputes. The terms of this Section 1 shall apply to all Disputes between you and Epson. The term
"Dispute" is meant to have the broadest meaning permissible under law and includes any dispute, claim,
controversy or action between you and Epson arising out of or relating to this Agreement, Epson
branded products (hardware and including any related software), or other transaction involving you and
Epson, whether in contract, warranty, misrepresentation, fraud, tort, intentional tort, statute, regulation,
ordinance, or any other legal or equitable basis. "DISPUTE" DOES NOT INCLUDE IP CLAIMS, or more
specifically, a claim or cause of action for (a) trademark infringement or dilution, (b) patent infringement,
(c) copyright infringement or misuse, or (d) trade secret misappropriation (an "IP Claim"). You and Epson
304
also agree, notwithstanding Section 1.6,that a court, not an arbitrator, may decide if a claim or cause of
action is for an IP Claim.
1.2 Binding Arbitration. You and Epson agree that all Disputes shall be resolved by binding arbitration
according to this Agreement. ARBITRATION MEANS THAT YOU WAIVE YOUR RIGHT TO A JUDGE
OR JURY IN A COURT PROCEEDING AND YOUR GROUNDS FOR APPEAL ARE LIMITED.
Pursuant to this Agreement, binding arbitration shall be administered by JAMS, a nationally recognized
arbitration authority, pursuant to its code of procedures then in effect for consumer related disputes, but
excluding any rules that permit joinder or class actions in arbitration (for more detail on procedure, see
Section 1.6 below). You and Epson understand and agree that (a) the Federal Arbitration Act (9 U.S.C.
§1, et seq.) governs the interpretation and enforcement of this Section 1, (b) this Agreement
memorializes a transaction in interstate commerce, and (c) this Section 1 shall survive termination of this
Agreement.
1.3 Pre-Arbitration Steps and Notice. Before submitting a claim for arbitration, you and Epson agree to
try, for sixty (60) days, to resolve any Dispute informally. If Epson and you do not reach an agreement to
resolve the Dispute within the sixty (60) days), you or Epson may commence an arbitration. Notice to
Epson must be addressed to: Epson America, Inc., ATTN: Legal Department, 3840 Kilroy Airport Way,
Long Beach, CA 90806 (the "Epson Address"). The Dispute Notice to you will be sent to the most recent
address Epson has in its records for you. For this reason, it is important to notify us if your address
changes by emailing us at EAILegal@ea.epson.com or writing us at the Epson Address above. Notice of
the Dispute shall include the sender's name, address and contact information, the facts giving rise to the
Dispute, and the relief requested (the "Dispute Notice"). Following receipt of the Dispute Notice, Epson
and you agree to act in good faith to resolve the Dispute before commencing arbitration.
1.4 Small Claims Court. Notwithstanding the foregoing, you may bring an individual action in the small
claims court of your state or municipality if the action is within that court's jurisdiction and is pending only
in that court.
1.5 WAIVER OF CLASS ACTIONS AND CLASS ARBITRATIONS. YOU AND EPSON AGREE THAT
EACH PARTY MAY BRING DISPUTES AGAINST THE OTHER PARTY ONLY IN AN INDIVIDUAL
CAPACITY, AND NOT AS A PLAINTIFF OR CLASS MEMBER IN ANY CLASS OR
REPRESENTATIVE PROCEEDING, INCLUDING WITHOUT LIMITATION FEDERAL OR STATE
CLASS ACTIONS, OR CLASS ARBITRATIONS. CLASS ACTION LAWSUITS, CLASS-WIDE
ARBITRATIONS, PRIVATE ATTORNEY-GENERAL ACTIONS, AND ANY OTHER PROCEEDING
WHERE SOMEONE ACTS IN A REPRESENTATIVE CAPACITY ARE NOT ALLOWED.
ACCORDINGLY, UNDER THE ARBITRATION PROCEDURES OUTLINED IN THIS SECTION, AN
ARBITRATOR SHALL NOT COMBINE OR CONSOLIDATE MORE THAN ONE PARTY'S CLAIMS
WITHOUT THE WRITTEN CONSENT OF ALL AFFECTED PARTIES TO AN ARBITRATION
PROCEEDING.
1.6 Arbitration Procedure. If you or Epson commences arbitration, the arbitration shall be governed by
the rules of JAMS that are in effect when the arbitration is filed, excluding any rules that permit arbitration
on a class or representative basis (the "JAMS Rules"), available at http://www.jamsadr.com or by calling
305
1-800-352-5267, and under the rules set forth in this Agreement. All Disputes shall be resolved by a
single neutral arbitrator, and both parties shall have a reasonable opportunity to participate in the
selection of the arbitrator. The arbitrator is bound by the terms of this Agreement. The arbitrator, and not
any federal, state or local court or agency, shall have exclusive authority to resolve all disputes arising
out of or relating to the interpretation, applicability, enforceability or formation of this Agreement,
including any claim that all or any part of this Agreement is void or voidable. Notwithstanding this broad
delegation of authority to the arbitrator, a court may determine the limited question of whether a claim or
cause of action is for an IP Claim, which is excluded from the definition of "Disputes" in Section 1.1
above. The arbitrator shall be empowered to grant whatever relief would be available in a court under
law or in equity. The arbitrator may award you the same damages as a court could, and may award
declaratory or injunctive relief only in favor of the individual party seeking relief and only to the extent
necessary to provide relief warranted by that party's individual claim. In some instances, the costs of
arbitration can exceed the costs of litigation and the right to discovery may be more limited in arbitration
than in court. The arbitrator's award is binding and may be entered as a judgment in any court of
competent jurisdiction.
You may choose to engage in arbitration hearings by telephone. Arbitration hearings not conducted by
telephone shall take place in a location reasonably accessible from your primary residence, or in Orange
County, California, at your option.
a) Initiation of Arbitration Proceeding. If either you or Epson decides to arbitrate a Dispute, both parties
agree to the following procedure:
(i) Write a Demand for Arbitration. The demand must include a description of the Dispute and the amount
of damages sought to be recovered. You can find a copy of a Demand for Arbitration at
http://www.jamsadr.com ("Demand for Arbitration").
(ii) Send three copies of the Demand for Arbitration, plus the appropriate filing fee, to: JAMS, 500 North
State College Blvd., Suite 600 Orange, CA 92868, U.S.A.
(iii) Send one copy of the Demand for Arbitration to the other party (same address as the Dispute
Notice), or as otherwise agreed by the parties.
b) Hearing Format. During the arbitration, the amount of any settlement offer made shall not be disclosed
to the arbitrator until after the arbitrator determines the amount, if any, to which you or Epson is entitled.
The discovery or exchange of non-privileged information relevant to the Dispute may be allowed during
the arbitration.
c) Arbitration Fees. Epson shall pay, or (if applicable) reimburse you for, all JAMS filings and arbitrator
fees for any arbitration commenced (by you or Epson) pursuant to provisions of this Agreement.
d) Award in Your Favor. For Disputes in which you or Epson seeks $75,000 or less in damages exclusive
of attorney's fees and costs, if the arbitrator's decision results in an award to you in an amount greater
than Epson's last written offer, if any, to settle the Dispute, Epson will: (i) pay you $1,000 or the amount
of the award, whichever is greater; (ii) pay you twice the amount of your reasonable attorney's fees, if
306
any; and (iii) reimburse you for any expenses (including expert witness fees and costs) that your attorney
reasonably accrues for investigating, preparing, and pursuing the Dispute in arbitration. Except as
agreed upon by you and Epson in writing, the arbitrator shall determine the amount of fees, costs, and
expenses to be paid by Epson pursuant to this Section 1.6d).
e) Attorney's Fees. Epson will not seek its attorney's fees and expenses for any arbitration commenced
involving a Dispute under this Agreement. Your right to attorney's fees and expenses under Section
1.6d) above does not limit your rights to attorney's fees and expenses under applicable law;
notwithstanding the foregoing, the arbitrator may not award duplicative awards of attorney's fees and
expenses.
1.7 Opt-out. You may elect to opt-out (exclude yourself) from the final, binding, individual
arbitration procedure and waiver of class and representative proceedings specified in this
Agreement by sending a written letter to the Epson Address within thirty (30) days of your assent
to this Agreement (including without limitation the purchase, download, installation of the
Software or other applicable use of Epson Hardware, products and services) that specifies (i)
your name, (ii) your mailing address, and (iii) your request to be excluded from the final, binding
individual arbitration procedure and waiver of class and representative proceedings specified in
this Section 1. In the event that you opt-out consistent with the procedure set forth above, all
other terms shall continue to apply, including the requirement to provide notice prior to litigation.
1.8 Amendments to Section 1. Notwithstanding any provision in this Agreement to the contrary, you
and Epson agree that if Epson makes any future amendments to the dispute resolution procedure and
class action waiver provisions (other than a change to Epson's address) in this Agreement, Epson will
obtain your affirmative assent to the applicable amendment. If you do not affirmatively assent to the
applicable amendment, you are agreeing that you will arbitrate any Dispute between the parties in
accordance with the language of this Section 1 (or resolve disputes as provided for in Section 1.7, if you
timely elected to opt-out when you first assented to this Agreement).
1.9 Severability. If any provision in this Section 1 is found to be unenforceable, that provision shall be
severed with the remainder of this Agreement remaining in full force and effect. The foregoing shall not
apply to the prohibition against class or representative actions as provided in Section 1.5. This
means that if Section 1.5 is found to be unenforceable, the entire Section 1 (but only Section 1)
shall be null and void.
Parent topic: Notices
Trademarks
EPSON®, Instant Off®, and Quick Corner®are registered trademarks, Epson iProjection is a trademark,
and EPSON Exceed Your Vision is a registered logomark of Seiko Epson Corporation.
PrivateLine®is a registered trademark; SizeWiseTM is a trademark; and Extra CareSM is a service mark of
Epson America, Inc.
307
Windows is a registered trademark of Microsoft Corporation in the United States and/or other countries.
Mac, macOS, and OS X are trademarks of Apple Inc., registered in the U.S. and other countries.
Google®is a registered trademark and AndroidTM , ChromebookTM , and Google ChromeTM are
trademarks of Google LLC.
HDBaseTTM and the HDBaseT Alliance logo are trademarks of the HDBaseT Alliance.
General Notice: Other product names used herein are for identification purposes only and may be
trademarks of their respective owners. Epson disclaims any and all rights in those marks.
Parent topic: Notices
Copyright Notice
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or
transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,
without the prior written permission of Seiko Epson Corporation. The information contained herein is
designed only for use with this Epson product. Epson is not responsible for any use of this information as
applied to other products.
Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third
parties for damages, losses, costs, or expenses incurred by purchaser or third parties as a result of:
accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this
product, or (excluding the U.S.) failure to strictly comply with Seiko Epson Corporation's operating and
maintenance instructions.
Seiko Epson Corporation shall not be liable for any damages or problems arising from the use of any
options or any consumable products other than those designated as Original Epson Products or Epson
Approved Products by Seiko Epson Corporation.
This information is subject to change without notice.
A Note Concerning Responsible Use of Copyrighted Materials
Copyright Attribution
Parent topic: Notices
308
A Note Concerning Responsible Use of Copyrighted Materials
Epson encourages each user to be responsible and respectful of the copyright laws when using any
Epson product. While some countries' laws permit limited copying or reuse of copyrighted material in
certain circumstances, those circumstances may not be as broad as some people assume. Contact your
legal advisor for any questions regarding copyright law.
Parent topic: Copyright Notice
Copyright Attribution
© 2019 Epson America, Inc.
11/19
CPD-56230
Parent topic: Copyright Notice