Eufy Video Doorbell 1080p User Manual
Displayed below is the user manual for Video Doorbell 1080p by Eufy which is a product in the Doorbell Kits category. This manual has pages.
Related Manuals
Anker Innovations Limited. All rights reserved. eufy Security and eufy Security
Logo are trademarks of Anker Innovations Limited, registered in the United
States and other countries. All other trademarks are the property of their
respective owners.
51005002471 V01
QUICK
START GUIDE
Video Doorbell 1080p (Battery-Powered)
TABLE OF
CONTENTS
What’s Included
01 09
Finding a Mounting Spot
Product Overview
03 11
Mounting the Bracket
How the System Works
04 14
Mounting the Doorbell
Powering on the Wi-Fi Doorbell Chime
05 15
Detaching the Doorbell
Setting up the System
07 16
Recharging the Doorbell
Charging Your Doorbell
08 17
Notice
01 English English 02
WHAT’S INCLUDED
For Video Doorbell Installation
QSG
Video Doorbell 1080p
(Battery-Powered)
Model: T8222
Screw Packs (Spare
screws and anchors are
included)
Quick Start
Guide
Screw Hole
Positioning Card
Doorbell
Detaching Pin
15° Mounting
Wedge
(Optional)
Mounting Bracket
FCC ID: 2AOKB-T8220
IC: 23451-T8220
USB Charging
Cable
For Wi-Fi Doorbell Chime Installation
Model: Wi-Fi Doorbell Chime
FCC ID: 2AOKB-T8020
IC: 23451-T8020
Note: Power plug may vary in different regions.
Power Plug
03 English English 04
PRODUCT OVERVIEW
Video Doorbell (Battery Powered)
Front view:
1
3
5
7
2
4
6
1. Motion Sensor
2. Microphone
3. Camera Lens
4. Ambient Light Sensor
5. Status LED
6. Doorbell Button
7. Speaker
Rear View:
1
2
3
1. Micro USB Charging Port
2. SYNC/RESET button
3. Detaching Mechanism
Operation How-to
Power on Press and release the SYNC button.
Add doorbell to Wi-Fi
Doorbell Chime
Press and hold the SYNC button until you hear a beep.
Power off the doorbell Quick-press the SYNC 5 times in 3 seconds.
Reset the doorbell Press and hold the SYNC button for 10 seconds.
HOW THE SYSTEM WORKS
How the System Works
The video doorbell system includes 2 parts:
• The video doorbell at your door
• The Wi-Fi Doorbell Chime in your house
The video doorbell detects motion at your porch and allows you to answer the door
anytime and anywhere. The Wi-Fi Doorbell Chime stores video clips on a microSD
card (user provides it) and works as an indoor digital chime. When someone rings the
doorbell, people in the house will be notied.
Doorbell Chime
Video Doorbell
05 English English 06
STEP 1 POWERING ON THE WI-FI
DOORBELL CHIME
Connect the Wi-Fi Doorbell Chime to the Internet
1. Fix the power connector to Wi-Fi Doorbell Chime.
① Place the power connector over Wi-Fi Doorbell Chime in the direction the
arrows indicate.
② Align the raised slots of the power connector with the notch on the base of
the doorbell chime.
③ Rotate clockwise to lock the power connector in place.
12 3
2. Extend Wi-Fi Doorbell Chime’s antennas.
3. Plug Wi-Fi Doorbell Chime into an AC power supply at your desired location. The
LED indicator turns solid green when the doorbell chime is ready for setup.
07 English English 08
STEP 2 SETTING UP THE SYSTEM
Download the App and Set up the System
Download the eufy Security app from the App Store (iOS devices) or Google Play
(Android devices).
Sign up for a eufy Security account and follow onscreen instructions to complete the
setup.
Tap Add Device and add the following devices:
1. Add the Wii-Fi Doorbell Chime.
2. Add the doorbell.
STEP 3 CHARGING YOUR
DOORBELL
The doorbell comes with an 80% battery level for safe transportation. Fully charge it
before mounting the doorbell at your front door.
6 months
Note: The battery life varies depending on usage. In most common cases, a
doorbell may have up to 15 events per day and each recording lasts 20 seconds on
average. Under this scenario, the doorbell battery life can last up to 4 months.
09 English English 10
STEP 4 FINDING A MOUNTING SPOT
Find a Mounting Spot
Take the Video Doorbell to your front door and check the live view on the eufy
Security app at the same time. Find a position where you can get the desired eld of
view.
Consider the below factors:
1. Check if you can reuse the existing holes and anchors on the wall or door frame.
2. If you want to place the doorbell close to a side wall, make sure the wall doesn’t
show up in the eld of view. Otherwise IR light will be reected and night vision
will become blurry.
3. If you are drilling the mounting holes for the first time the recommended
mounting height is 48" / 1.2m from the ground.
4. Use the 15° mounting wedge as a supplementary mounting bracket if you wish to
see more on a specic side.
1.76m(5’9”)
1.2m (48")
0.3m
(12")
1m
(40")
Video Doorbell
Without 15° Mounting wedge
Door Video Doorbell
With 15° Mounting wedge
Door
15°
Place the Screw Hole Positioning Card against the wall to mark the position.
11 English English 12
STEP 5 MOUNTING THE BRACKET
Mount the Doorbell on a Wooden Surface
If you’re mounting the doorbell on a wooden surface, you don’t need to pre-drill
pilot holes. Use the provided screws to secure the Mounting Bracket on the wall. The
Screw Hole Positioning Card indicates the position of the screw holes.
What is required: Power Drill, Mounting Bracket, 15° Mounting Wedge
(Optional), Screw Packs
Phillips-Head Screwdriver
(User provides it.)
15° Mounting
Wedge (Optional)
Screw Packs (Spare screws
and anchors are included.)
Mounting Bracket
(Attached to 15° Mounting Wedge)
Without 15° Mounting Wedge With 15° Mounting Wedge
Mounting
Bracket
Wall Mounting
Wedge
Mounting
Bracket
Wall
Mount the Video Doorbell on Surfaces Made Out of
Hard Materials
1. If you’re mounting the doorbell on a surface made out of hard materials, like brick,
concrete, stucco, drill 2 holes through the Screw Hole Positioning Card with
15/64”(6mm) drill bit.
2. Insert the provided anchors, and then use the provided long screws to secure the
Mounting Bracket on the wall.
What is required: Power Drill, 15/64”(6mm) Drill Bit, Mounting Bracket, 15°
Mounting Wedge (Optional), Screw Packs
12
15° Mounting
Wedge (Optional)
Mounting Bracket
(Attached to 15° Mounting Wedge)
Without 15° Mounting Wedge With 15° Mounting Wedge
Mounting
Bracket
Wall Mounting
Wedge
Mounting
Bracket
Wall
Power Drill with
1/4" (6.35mm) Drill Bit
(User provides it.)
Screw Packs (Spare screws
and anchors are included.)
15/64”(6 mm) Drill Bit
1
2
15° Mounting
Wedge (Optional)
Mounting Bracket
(Attached to 15° Mounting Wedge)
Without 15° Mounting Wedge With 15° Mounting Wedge
Mounting
Bracket
Wall Mounting
Wedge
Mounting
Bracket
Wall
Power Drill with
1/4" (6.35mm) Drill Bit
(User provides it.)
Screw Packs (Spare screws
and anchors are included.)
15/64”(6 mm) Drill Bit
13 English English 14
1
2
15° Mounting
Wedge (Optional)
Mounting Bracket
(Attached to 15° Mounting Wedge)
Without 15° Mounting Wedge With 15° Mounting Wedge
Mounting
Bracket
Wall Mounting
Wedge
Mounting
Bracket
Wall
Power Drill with
1/4" (6.35mm) Drill Bit
(User provides it.)
Screw Packs (Spare screws
and anchors are included.)
15/64”(6 mm) Drill Bit
STEP 6 MOUNTING THE DOORBELL
Mount the Doorbell
Align the doorbell with the top of the mount and then snap the bottom into place.
You’re all set!
If you want to detach the doorbell or recharge it, please refer to the following
sections.
15 English English 16
APPENDIX 1 DETACHING THE DOORBELL
Detach the Doorbell
1. Use the doorbell detaching pin provided if you wish to detach the doorbell from
the Mounting Bracket.
2. Insert and press the detaching pin into the hole on the bottom of the doorbell
and then lift to take the bottom of the doorbell off.
What is required: Doorbell Detaching Pin
Doorbell
Detaching Pin
APPENDIX 2 RECHARGING THE
DOORBELL
Recharge the Doorbell
Charge the doorbell with universal USB chargers that deliver 5V 1A output.
LED indication Charging: Solid orange
Fully charged: Solid blue
Charging time 6 hours from 0% to 100%
17 English English 18
NOTICE
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
Warning: Changes or modications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of
the following measures: (1) Reorient or relocate the receiving antenna. (2) Increase the
separation between the equipment and receiver. (3) Connect the equipment into an
outlet on a circuit different from that to which the receiver is connected. (4) Consult
the dealer or an experienced radio / TV technician for help.
FCC Radio Frequency Exposure Statement
The device has been evaluated to meet general RF exposure requirements. The device
can be used in xed/mobile exposure condition. The min separation distance is 20cm.
Notice: Shielded cables
All connections to other computing devices must be made using shielded cables to
maintain compliance with FCC regulations.
The following importer is the responsible party:
Company Name: POWER MOBILE LIFE, LLC
Address: 400 108th Ave NE Ste 400, Bellevue, WA 98004-5541
Telephone: 1-800-988-7973
This product complies with the radio interference requirements of the European
Community.
Declaration of Conformity
Hereby, Anker Innovations Limited declares that this device is in compliance with the
essential requirements and other relevant provisions of Directive 2014/53/EU. For the
declaration of conformity, visit the Web site: https://www.eufylife.com/.
This product can be used across EU member states.
Do not use the Device in the environment at too high or too low temperature, never
expose the Device under strong sunshine or too wet environment.
The suitable temperature for T8020 and accessories is 0°C-40°C.
The suitable temperature for T8222 and accessories is -20°C-50°C.
When charging, please place the device in an environment that has a normal room
temperature and good ventilation.
It is recommended to charge the device in an environment with a temperature that
ranges from 5°C~25°C.
RF exposure information: The Maximum Permissible Exposure (MPE) level has been
calculated based on a distance of d=20 cm between the device and the human body. To
maintain compliance with RF exposure requirement, use product that maintain a 20cm
distance between the device and human body.
CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT
TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS
Wi Operating Frequency Range: 2412~2472MHz (2.4G)
Wi Max Output Power: 15.68dBm (ERIP for T8020); 15.01dBm (ERIP for T8220)
Bluetooth Operating Frequency Range: 2402~2480MHz; Bluetooth Max Output Power:
2.048dBm (EIRP)
The following importer is the responsible party (contact for EU matters only)
Importer: Anker Technology (UK) Ltd
Importer Address: Suite B, Fairgate House, 205 Kings Road, Tyseley, Birmingham, B11
2AA, United Kingdom
This product is designed and manufactured with high quality materials and
components, which can be recycled and reused.
19 English
This symbol means the product must not be discarded as household waste,
and should be delivered to an appropriate collection facility for recycling.
Proper disposal and recycling helps protect natural resources, human health
and the environment. For more information on disposal and recycling of this
product, contact your local municipality, disposal service, or the shop where
you bought this product.
IC Statement
This device complies with Industry Canada licence-exempt RSS standard(s). Operation
is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause
undesired operation of the device."
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
IC RF Statement:
When using the product, maintain a distance of 20cm from the body to ensure
compliance with RF exposure requirements.
Lors de l'utilisation du produit, maintenez une distance de 20 cm du corps an de
vous conformer aux exigences en matière d'exposition RF.
CUSTOMER SERVICE
Warranty
12-month limited warranty
(US) +1 (800) 988 7973 Mon-Fri 9:00-17:00 (PT)
(UK) + 44 (0) 1604 936 200 Mon-Fri 6:00-11:00 (GMT)
(DE) +49 (0) 69 9579 7960 Mon-Fri 6:00-11:00
Customer Support: support@eufylife.com
Anker Innovations Limited
Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon,
Hong Kong