Gigabyte GC-WBAX200 User Manual
Displayed below is the user manual for GC-WBAX200 by Gigabyte which is a product in the Network Cards category. This manual has pages.
Related Manuals
GC-WBAX200
Installation Guide/安裝指南
安装指南/インストールガイド
Installationsanleitung
12WE6-WBAX200-11AR
- 2 -
Installing the Wi-Fi/Bluetooth Card • 安裝Wi-Fi/藍牙卡
安装Wi-Fi/蓝牙卡 • Wi-Fi/Bluetoothカードを取り付ける
Installation der Wi-Fi/Bluetooth-Karte
Antenna Connector
天線連接埠
天线连接端口
アンテナ コネクター
Antennenanschluss
Wi-Fi/Bluetooth Card
Wi-Fi/藍牙卡 • Wi-Fi/蓝牙卡
Wi-Fi/Bluetoothカード
Wi-Fi/Bluetooth-Karte
USB Connector
USB連接埠插座
USB连接端口插座
USBコネクター
USB-Anschluss
Antenna • 天線
天线 • アンテナ• Antenne
USB Cable • USB排線
USB排线 • USBケーブル
USB-Kabel
- 3 -
Step 1:
Install the Wi-Fi/Bluetooth card in a PCI Express x1
slot. Connect one end of the USB cable to the USB
connector on the Wi-Fi/Bluetooth card.
步驟一：
先將Wi-Fi/藍牙卡安裝至PCI Express x1 插
槽，接著將USB排線的一端接至無線/藍
牙卡的USB連接埠插座。
步骤一：
先将Wi-Fi/蓝牙卡安装至PCI Express x1插
槽，接着将USB排线的一端接至无线/蓝
牙卡的USB连接端口插座。
ステップ 1:
Wi-Fi/Bluetooth カードを PCI Express x1 スロ
ットに装着します。USB ケーブルの一方の
端を Wi-Fi/Bluetooth カードの USB コネクタ
に接続します。
Schritt 1:
Installieren Sie die Wi-Fi/Bluetooth-Karte in einem
PCI Express x1-Steckplatz. Verbinden Sie ein
Ende des USB-Kabels mit dem USB-Anschluss
auf der Wi-Fi/Bluetooth-Karte.
- 4 -
Step 2:
Connect the other end of the USB cable to the
F_USB connector on the motherboard.
步驟二：
再將USB排線的另一端接至主機板的
F_USB插座。
步骤二：
再将USB排线的另一端接至主板的F_USB
插座。
ステップ 2:
USB ケーブルのもう一方の端をマザー
ボードの F_USB コネクタに接続します。
Schritt 2:
Verbinden Sie das andere Ende des USB-Kabels
mit dem F_USB-Anschluss auf dem Motherboard.
- 5 -
Step 3:
Tighten the antenna cables to the antenna
connectors on the Wi-Fi/Bluetooth card
respectively.
步驟三：
將天線鎖至Wi-Fi/藍牙卡的天線連接埠。
步骤三：
将天线锁至Wi-Fi/蓝牙卡的天线连接端
口。
ステップ 3:
アン テナケ ーブ ル を そ れ ぞ れ Wi-Fi/
Bluetooth カードのアンテナコネクターに
しっかりと接続します。
Schritt 3:
Befestigen Sie die Antennenkabel gut an den
jeweiligen Antennenanschlüssen auf der Wi-Fi/
Bluetooth-Karte.
- 6 -
Step 4:
Then move the antennas to a place where the
signal is good.
步驟四：
完成安裝後將天線移至收訊良好處。
步骤四：
完成安装后将天线移至收讯良好处。
ステップ 4:
次に、ワイヤレス信号が受信し易い場所
にアンテナを配置します。
Schritt 4:
Setzen Sie die Antennen dann auf eine Stelle mit
gutem Signalempfang.
- 7 -
After the computer starts, install the
driver for the Wi-Fi/Bluetooth Card.
Adjust your wireless LAN configuration
based on your environment after
installing the driver.
啟動電腦後請安裝Wi-Fi/藍牙卡驅
動程式。完成後即可依環境中的
無線網路選擇連接。
Installing the Drivers and Utilities • 安裝驅動程式及工具
安装驱动程序及工具 •
ドライバとユーティリティをインストールする
Installation der Treiber und Dienstprogramme
启动电脑后请安装Wi-Fi/蓝牙卡驱动程序。完成后即可依环境中的无线网络选
择连接。
コンピュータが起動した後、Wi-Fi/Bluetoothカードのドライバーをインストールし
てください。ドライバーをインストールした後に、ご使用の環境に基づいて、ワイ
ヤレスLANの設定を行います。
Hat sich der Computer hochgefahren, installieren Sie den Treiber für die Wi-Fi/Bluetooth-
Karte. Passen Sie nach Installation des Treibers Ihre WLAN-Konfiguration entsprechend
Ihrer Umgebung an.
- 8 -
Regulatory Notices
Supplier’s Declaration of Conformity
47 CFR § 2.1077 Compliance Information
Product Name: PCIe add-in card
Trade Name: GIGABYTE
Model Number: GC-WBAX200
Responsible Party – U.S. Contact Information: G.B.T. Inc.
Address: 17358 Railroad street, City Of Industry, CA91748
Tel.: 1-626-854-9338
Internet contact information: https://www.gigabyte.com
FCC Compliance Statement:
This device complies with Part 15 of the FCC Rules, Subpart B, Unintentional Radiators.
Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause undesired operation.
CAUTION:
The manufacturer is not responsible for any interference caused by unauthorized modifications and/or use of unauthorized
antennas. Such changes and/or modifications not expressly approved by the party responsible for compliance of this device could
void the user’s authority to operate the equipment
RF exposure statement / Antenna Use
Further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to
lower output power if such function is available.
•Do not touch or move antenna while the unit is transmitting or receiving.
•Do not hold any component containing the radio such that the antenna is very close or touching any exposed parts of the body,
especially the face or eyes, while transmitting.
•Do not operate the radio or attempt to transmit data unless the antenna is connected; this behavior may cause damage to the
radio.
United States of America, Federal Communications Commission Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with manufacturer’s
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
- 9 -
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
Notice for 5GHz
Operations in the 5.15-5.25GHz band are restricted to indoor usage only. (For 5GHz only)
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio
Interference Regulations of the Canadian Department of Communications. This class B digital apparatus complies with Canadian
ICES-003.
Avis de conformité à la réglementation d’Industrie Canada
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Canada-Industry Canada (IC) Regulatory statement
This device complies with Canadian RSS-210.
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Cet appareil se conforme aux normesCanada d’Industrie de RSS permis-exempt. L’utilisation est assujetti aux deux conditions
suivantes: (1) cet appareil ne peut pas causer d’interférences, et (2) cet appareil doit accepter des interférences, y compris des
interférences qui peuvent causer desopérations non désirées de l’appareil.
Caution: When using IEEE 802.11a wireless LAN, this product is restricted to indoor use due to its operation in the 5.15-to 5.25-GHz
frequency range. Industry Canada requires this product to be used indoors for the frequency range of 5.15 GHz to 5.25 GHz to reduce
the potential for harmful interference to co-channel mobile satellite systems. High power radar is allocated as the primary user of the 5.25-
to 5.35-GHz and 5.65 to 5.85-GHz bands. These radar stations can cause interference with and/or damage to this device. The maximum
allowed antenna gain for use with this device is 6dBi in order to comply with the E.I.R.P limit for the 5.25-to 5.35 and 5.725 to 5.85 GHz
frequency range in point-to-point operation. To comply with RF exposure requirements all antennas should be located at a minimum
distance of 20cm, or the minimum separation distance allowed by the module approval, from the body of all persons.
Attention: l’utilisation d’un réseau sans fil IEEE802.11a est restreinte à une utilisation en intérieur à cause du fonctionnement dansla bande
de fréquence 5.15-5.25 GHz. Industry Canada requiert que ce produit soit utilisé à l’intérieur des bâtiments pour la bande de fréquence
5.15-5.25 GHz afin de réduire les possibilités d’interférences nuisibles aux canaux co-existants des systèmes de transmission satellites.
Les radars de puissances ont fait l’objet d’une allocation primaire de fréquences dans les bandes 5.25-5.35 GHz et 5.65-5.85 GHz. Ces
stations radar peuvent créer des interférences avec ce produit et/ou lui être nuisible. Le gain d’antenne maximum permissible pour une
utilisation avec ce produit est de 6 dBi afin d’être conforme aux limites de puissance isotropique rayonnée équivalente (P.I.R.E.) applicable
dans les bandes 5.25-5.35 GHz et 5.725-5.85 GHz en fonctionnement point-à-point. Pour se conformer aux conditions d’exposition de
- 10 -
RF toutes les antennes devraient être localisées à une distance minimum de 20 cm, ou la distance de séparation minimum permise par
l’approbation du module, du corps de toutes les personnes.”
Radiation Exposure Statement:
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser)
gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and
its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful
communication.
Selon les règlements de Canada d’Industrie, cet émetteur de radio peut seulement fonctionner en utilisant une antenne du typeet
de gain maximum (ou moindre) que le gainapprouvé pour l’émetteur par Canada d’Industrie. Pour réduire lesinterférencesradio
potentiellesavec les autres utilisateurs, le type d’antenne et son gain devraient êtrechoisis de façon à ce que la puissance isotrope
rayonnée équivalente(P.I.R.E.)ne soit pas supérieure à celle qui estnécessaire pour une communication réussie.
European Union (EU) CE Declaration of Conformity
This device complies with the following directives: Electromagnetic Compatibility Directive 2014/30/EU, Low-voltage Directive
2014/35/EU, Radio Equipment Directive (RED) 2014/53/EU, RoHS directive (recast) 2011/65/EU & the 2015/863 Statement.
This product has been tested and found to comply with all essential requirements of the Directives.
European Union (EU) RoHS (recast) Directive 2011/65/EU & the European Commission Delegated Directive (EU) 2015/863
Statement
GIGABYTE products have not intended to add and safe from hazardous substances (Cd, Pb, Hg, Cr+6, PBDE, PBB, DEHP, BBP,
DBP and DIBP). The parts and components have been carefully selected to meet RoHS requirement. Moreover, we at GIGABYTE
are continuing our efforts to develop products that do not use internationally banned toxic chemicals.
European Union (EU) Community Waste Electrical & Electronic Equipment (WEEE) Directive Statement
GIGABYTE will fulfill the national laws as interpreted from the 2012/19/EU WEEE (Waste Electrical and Electronic Equipment) (recast)
directive. The WEEE Directive specifies the treatment, collection, recycling and disposal of electric and electronic devices and their
components. Under the Directive, used equipment must be marked, collected separately, and disposed of properly.
WEEE Symbol Statement
The symbol shown below is on the product or on its packaging, which indicates that this product must not be disposed
of with other waste. Instead, the device should be taken to the waste collection centers for activation of the treatment,
collection, recycling and disposal procedure.
For more information about where you can drop off your waste equipment for recycling, please contact your local
government office, your household waste disposal service or where you purchased the product for details of environmentally safe
recycling.
- 11 -
End of Life Directives-Recycling
The symbol shown below is on the product or on its packaging, which indicates that this product must not be disposed of
with other waste. Instead, the device should be taken to the waste collection centers for activation of the treatment,
collection, recycling and disposal procedure.
Déclaration de Conformité aux Directives de l’Union européenne (UE)
Cet appareil portant la marque CE est conforme aux directives de l’UE suivantes: directive Compatibilité Electromagnétique
2014/30/UE, directive Basse Tension 2014/35/UE, directive RED (équipements radioélectriques) 2014/53/UE, la directive RoHS II
2011/65/UE & la déclaration 2015/863. La conformité à ces directives est évaluée sur la base des normes européennes
harmonisées applicables.
European Union (EU) CE-Konformitätserklärung
Dieses Produkte mit CE-Kennzeichnung erfüllen folgenden EU-Richtlinien: EMV-Richtlinie 2014/30/EU, Niederspannungsrichtlinie
2014/30/EU, Richtlinie RED (Funkanlagen ) 2014/53/EU, RoHS-Richtlinie 2011/65/EU erfüllt und die 2015/863 Erklärung.
Die Konformität mit diesen Richtlinien wird unter Verwendung der entsprechenden Standards zurEuropäischen Normierung
beurteilt.
CE declaração de conformidade
Este produto com a marcação CE estão em conformidade com das seguintes Diretivas UE: Diretiva Baixa Tensão 2014/35/EU;
Diretiva CEM 2014/30/EU; Diretiva de equipamentos de rádio 2014/53/EU; Diretiva RSP 2011/65/UE e a declaração 2015/863.
A conformidade com estas diretivas é verificada utilizando as normas europeias harmonizadas.
CE Declaración de conformidad
Este producto que llevan la marca CE cumplen con las siguientes Directivas de la Unión Europea: Directiva EMC (2014/30/EU),
Directiva de bajo voltaje (2014/35/EU), Directiva de equipos radioeléctricos 2014/53/EU, Directiva RoHS (recast) (2011/65/EU) y la
Declaración 2015/863.
El cumplimiento de estas directivas se evalúa mediante las normas europeas armonizadas.
Dichiarazione di conformità CE
Questo prodotto è conforme alle seguenti direttive: Direttiva sulla compatibilità elettromagnetica 2014/30/UE, Direttiva sulle
apparecchiature radio (RED) 2014/53/UE, Direttiva sulla bassa tensione 2014/35/UE, Direttiva RoHS (rifusione) 2011/65/UE e
Dichiarazione 2015/863.
Questo prodotto è stato testato e trovato conforme a tutti i requisiti essenziali delle Direttive.
Contact point for EU based customers
G.B.T. Technology Trading GmbH
Am Stadtrand 63, 22047 Hamburg, Germany
tel: +49-40-25 33 040
- 12 -
European Community Directive RED Directive Compliance Statement:
This equipment is suitable for home and office use in all the European Community Member States and EFTA Member States.
The low band 5.15 -5.35 GHz is for indoor use only for the countries listed in the table below:
AT BE BG CH CY CZ DE
DK EE EL ES FI FR HR
HU IE IS IT LI LT LU
LV MT NL PL PT RO SE
SI SK TR UK
Wireless module country approvals:
Wireless module model name: AX200NGW
Wireless module manufacturer: Intel® Corporation
- 13 -
China RoHS Compliance Statement
中国《废弃电器电子产品回收处理管理条例》提示性说明
为了更好地关爱及保护地球，当用户不再需要此产品或产品寿命终止时，请遵守国家废弃电器电子产品回
收处理相关法律法规，将其交给当地具有国家认可的回收处理资质的厂商进行回收处理。
环保使用期限
Environment-friendly use period
此标识指期限（十年），电子电气产品中含有的有害物质不会发生外泄或突变、电子电气产品用
户正常使用该电子电气产品不会对环境造成严重 污染或对其人身、财产造成严重损害的期限。
关于符合中国《电器电子产品有害物质限制使用管理办法》的声明
Administrative Measures for the Restricted Use of Hazardous Substances in Electrical and Electronic Products
(China RoHS Declaration)
产品中有害物质的名称及含量
Hazardous Substances Table
部件名称(Parts)
有害物质(Hazardous Substances)
铅
(Pb)
汞
(Hg)
镉
(Cd)
六价铬
(Cr(VI))
多溴联苯
(PBB)
多溴二
苯醚
(PBDE)
印刷电路板总成
PCB Assembly × ○ ○ ○ ○ ○
连接器
Connector × ○ ○ ○ ○ ○
机械零件-金属
Mechanical parts-Metal × ○ ○ ○ ○ ○
机械零件-塑胶
Mechanical parts-Plastic ○ ○ ○ ○ ○ ○
线材
Cable ○ ○ ○ ○ ○ ○
These tables are prepared in accordance with the provisions of SJT 11364
本表格依据SJ/T 11364 的规定编制。
○： The content of such hazardous substance in all homogeneous materials of such component is below the
limit required by GB/T 26572.
表示该有害物质在该部件所有均质材料中的含量均在GB/T 26572规定的限量要求以下。
×： The content of such hazardous substance in a certain homogeneous material of such component is beyond
the limit required by GB/T 26572.
表示该有害物质至少在该部件的某一均质材料中的含量超出GB/T 26572 规定的限量要求
- 14 -
BSMI CNS15663 限用物質含有情況標示聲明書
Declaration of the Presence Condition of the Restricted Substances Marking
設備名稱：Wi-Fi/Bluetooth Card 型號（型式）：GC-WBAX200
Equipment name Type designation (Type)
單元Unit
限用物質及其化學符號
Restricted substances and its chemical symbols
鉛
Lead
(Pb)
汞
Mercury
(Hg)
鎘
Cadmium
(Cd)
六價鉻
Hexavalent
chromium
(Cr+6)
多溴聯苯
Polybrominated
biphenyls
(PBB)
多溴二苯醚
Polybrominated
diphenyl ethers
(PBDE)
印刷電路板總成
PCB Assembly － ○ ○ ○ ○ ○
連接器
Connectors － ○ ○ ○ ○ ○
機械零件-金屬
Mechanical parts-Metal － ○ ○ ○ ○ ○
機械零件-塑膠
Mechanical parts-Plastic ○ ○ ○ ○ ○ ○
線材 Cables ○ ○ ○ ○ ○ ○
備考1. "超出0.1 wt %" 及 "超出0.01 wt %" 係指限用物質之百分比含量超出百分比含量基準值。
Note 1: "Exceeding 0.1 wt %" and "exceeding 0.01 wt %" indicate that the percentage content of the restricted substance
exceeds the reference percentage value of presence condition.
備考2. "○"係指該項限用物質之百分比含量未超出百分比含量基準值。
Note 2: "○" indicates that the percentage content of the restricted substance does not exceed the percentage of reference
value of presence.
備考3. "－"係指該項限用物質為排除項目。
Note 3: The "－" indicates that the restricted substance corresponds to the exemption.
Korea Wireless Statement:
5.15 — 5.35GHz 대역에서의 작동은 실내로。
Japan Wireless Statement:
5.15GHz帯 ~ 5.35GHz帯: 屋内のみの使用。
Taiwan NCC Wireless Statements / 無線設備警告聲明：
低功率電波輻射性電機管理辦法
第十二條：經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大
功率或變更原設計之特性及功能。
第十四條：低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，
並改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。低功率射
頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。
在5.25-5.35秭赫頻帶內操作之無線資訊傳輸設備，限於室內使用。