Hoover HDIH 2T1047-80 User Manual
Displayed below is the user manual for HDIH 2T1047-80 by Hoover which is a product in the Dishwashers category. This manual has pages.
Related Manuals
User Manual
Dishwasher
HDIH 2T1047-80
●
HMIH 2T1047-80
Thank you f
●
or purchasing a Hoover product
Please read t
●
hese instructions carefully before using this appliance. The
instructions contain important information which will help you get the best out of the
appliance and ensure safe and proper installation, use and maintenance.
Keep this manual
●
in a convenient place so you can always refer to it for the safe
and proper use of the appliance.
If you sell the appliance, give it away, or leave it behind when you move house,
make sure you also pass on this manual so that the new owner can become
familiar with the appliance and safety warnings.
Safety and warnings
●
......................................................................................
Installation instructions ..................................................................................
Product Description .......................................................................................
Overview of programmes...............................................................................
Content
1
4
21
22
Water softening system................................................................................. 24
Using rinse aid............................................................................................... 26
Utensils.......................................................................................................... 27
Loading utensils............................................................................................. 28
Adding detergent............................................................................................
Before first Use..............................................................................................
32
33
Daily Use........................................................................................................
Care and cleaning......................................
●
....................................................
Troubleshooting.............................................................................................
Technical Data...............................................................................................
34
36
39
43
How to make savings..................................................................................... 31
1
Your dishwasher has been carefully designed to operate safely during normal
●
dishwashing procedures. Please keep the following instructions in mind when you
are using your dishwasher.
●
Read all instructions before using the dishwasher.
●
The information in this manual must be followed to minimise the risk of re or
explosion or to prevent property damage, personal injury or loss of life.
Use the dishwasher only for its intended function as described in this user guide.
This appliance is intended to be used in household and similar applications such
●
as:
staff kitchen areas in shops, ofces and other working environments;
●
farm houses;
by clients in hotels, motels and other residential type environments;
bed and breakfast type environments.
Electrical shock hazard
Cut Hazard
When using your dishwasher, follow basic
precautions, including the following:
Safety and warnings
WARNING
WARNING
WARNING
Before installing the dishwasher, remove the house fuse or open the circuit breaker.
This appliance must be earthed. In the event of a malfunction or breakdown,
earthing will reduce the risk of electric shock by providing a path of least resistance
for electric current. This appliance is equipped with a cord having an equipment-
earthing conductor and an earthing plug. The plug must be plugged into an
appropriate outlet that is installed and earthed in accordance with all local codes
and ordinances.
WARNING - Improper connection of the equipment-earthing conductor can result in
a risk of electric shock. Check with a qualied electrician or service representative
if you are in doubt as to whether the appliance is properly earthed.
Do not modify the power supply plug provided with the appliance - if it will not t
the outlet, have a proper outlet installed by a qualied electrician. Do not use an
extension cord, adapter plug or multiple outlet box.
Failure to follow this advice may result in electrical shock or death.
Take care - panel edges are sharp.
Failure to use caution could result in injury or cuts.
2
Use only detergents or rinse aid recommended for use in a domestic dishwasher
and keep them out of reach of children.
Check that the detergent dispenser is empty after the completion of each wash
program.
When loading
●
items to be washed, locate sharp items so that they are not likely
to damage the dishwasher and load sharp knives with the handle up to reduce the
risk of cut-type injuries.
●
Do not touch the filter plate (the metal disc in the dishwasher base) during or
immediately after use, as it may be hot from the heater plate underneath.
Do not tamper with the controls.
Do not abuse, sit in, stand on the door or dish rack of the dishwasher.
Do not lean on the adjustable racks or use them to support your body weight.
To reduce the risk of injur
●
y, do not allow children to play in or on the dishwasher.
Under certain conditions, hydrogen gas may be produced in a hot water heater
system that has not been used for two weeks or more. Hydrogen gas is explosive.
If the hot water system has not been used for such a period, before using the
dishwasher, turn on all hot water taps and let the water flow from each for several
minutes.
●
This will release any accumulated hydrogen gas. As the gas is flammable,
do not smoke or use an open flame during this time.
Remove the door to the washing compartment when removing an old dishwasher
from service or discarding it.
Some dishwasher detergents are strongly alkaline. They can be extremely
dangerous if swallowed. Avoid contact with the skin and eyes and keep children
away from the dishwasher when the door is open. Check that the detergent
receptacle is empty after completion of the wash cycle.
Certified residential dishwashers are not intended for licensed food
establishments.
Maintenance safety instructions
Disconnect the appliance from the power supply before any cleaning or
maintenance.
When disconne
●
cting the appliance pull the plug rather than the power supply
cord or junction of cord to avoid damage.
Do not repair or replace any part of the appliance or attempt any servicing unless
specifically recommended in this user guide.
Keep the floor around your appliance clean and dry to reduce the possibility of
slipping.
Safety and warnings
3
Keep the area around/underneath your appliance free from the accumulation of
combustible materials, such as lint, pape
●
r, rags and chemicals.
Operational safety instructions
●
Open the door very carefully if the dishwasher is in operation. There is a risk of
being sprayed with hot water. Do not open the door fully until the spray arms have
stopped rotating.
The door should not be left in the open position as this could present a tripping
hazard.
The water inside the dishwasher is not suitable for drinking.
The dishwasher must be used with the filter plate, drain filter and spray arm(s) in
place. To identify what these parts are, see drawings in section ‘‘Care and Cleaning’
of this user guide.
Do not operate this dishwasher if it is damaged, malfunctioning, partially
disassembled or has missing or broken parts, including a damaged power supply
cord or plug.
Household appliances are not intended to be played with by children. Children of
less than 8 years old must be kept away from the appliance unless continuously
supervised. This appliance can be used by children aged from 8 years and
above, and persons
●
with reduced physical, sensory or mental capabilities or lack
of experience and knowledge, if they have been given supervision or instruction
concerning the use of the appliance in a safe way and they understand the hazards
involved.
Cleaning and user maintenance shall not be done by children without supervision.
Do not allow children
●
to play inside, on or with this appliance or any discarded
appliance.
If a dishwasher cleaner is used, we would strongly recommend a wash program
with detergent should be run immediately afterward, to prevent any damage to the
dishwashe
●
r.
The dishwasher is designed for washing normal household utensils. Items that
are contaminated by petrol, paint, steel or iron debris, corrosive, acidic or alkaline
chemicals are not to be washed in the dishwasher.
If the dishwasher is not being used for long periods of time, turn the electricity
and water supply to the dishwasher off.
Safety and warnings
4
Installation instructions
Parts supplied
Prior to installation
●
Unpacking and handling
Connections and services
●
Check packaging and dishwasher for signs of transport damage. If the
dishwasher is in any way damaged, do not install it. Contact the dealer the
dishwasher was purchased from.
Disposal of packaging: some of the packaging is recyclable. Check the symbols
and labels and recycle if possible.
Never lift the dishwasher from the door handle or the top panel. Doing so may
cause damage.
Always be careful with the hoses and power cord at the back of the dishwasher.
Careful handling will prevent damage and malfunction from squashing, kinking or cuts.
While installing the dishwasher, check the drain hose is not restricted or kinked.
Check that the
●
power cord is long enough to reach the outlet. If it isn’t, it must be
replaced by a haier authorised technician. Extension cords or multi-outlet power
boards should not be used to connect the dishwasher to the power supply.
Check that the hoses are long enough to reach the services. If a hose needs
extending, ensure that the extension hose is new and of equal quality and diameter
The dishwa
●
sher should not be connected to a water system where the
temperature exceeds 60oC.
The dishwasher must not be connected to an undersink high-pressure “push-
through” type hot water system, as damage to the system will result.
Drain hose
support (1)
Installation and
User Instructions
Inlet hose (1)
Ø4 x 25mm
screws (4)
Brackets for
toekick (2)
Ø3.5 x 44mm
screws (4)
Ø3.5 x 13mm
screws (10)
Moisture protection
tape (1) (to prevent
moisture damage to
cabinetry)
Installing the
fixings (2)
Salt funnel
5
Installation instructions
1Product dimensions
e
●
D
●
g
●
h
i
●
j
●
k
B
A
F
C
3.5-5kg
6
Installation instructions
M
●
M SNOISNEMID TCUDORP
A Overall height of product* 816 - 876
B Ov
●
erall width of product (excl. side seals) 448
C
●
Overall depth of product (excl. custom panel & handle) 559
D Depth of toekick 30 - 95
E Height from
●
floor to bottom of custom panel 100 - 153
F Depth
●
of open door
(measured from front of chassis) (excl. custom panel)
606
* depending on adjustment of levelling feet
CUSTOM PANEL DIMENSIONS (custom made) MM
G Height of custom door panel 660 - 713
444lenap rood motsuc fo htdiWH
I Depth of custom door panel 16 - 20
lenap kcikeot motsuc fo htdiWJ
140 -
75
***lenap kcikeot motsuc fo thgieHK
* depending on cabinetry dimensions
2
N
L
Cabinetry dimensions
PLAN
444
7
Installation instructions
M
●
Minimum clearances from adjacent cabine
●
try
min. 13 mm
●
clearance
●
from a corner
cupboard
min. 1 mm
clearance
to adjacent
cupboard door
PROFILE
MM SNOISNEMID YRTENIBAC
L452ytivac fo htdiw edisnI
M 818 - 878*ytivac fo thgieh edisnI
N775 .nimytivac fo htped edisnI
* depending on adjustment of levelling feet
3
8
Installation instructions
Cavity preparation
IMPORTANT!
●
The power outlet must be located
in a cabinet adjacent to the
dishwasher cavity.
Services can be located either
side of the dishwasher.
Ensure that any services hole has
a minimum diameter of 50mm.
Positioning and stabilising the dishwasher
Do not lift the dishwasher from the door handle.
As you push product in, pull through hoses and cord, ensuring they don’t get kinked or twisted.
Plastic spacers can now be inserted at the side of the dishwasher next to the hinge to improve
stabilitysee step 7 for details on fitting spacers
●After sliding the dishwasher into position, adjust back foot with a 6mm Allen key.
The front feet can be adjusted manually also.
We recommend that you adjust the feet so that the dishwasher sits securely under the
bench top so that it doesn’t tip.
Dia. 50mm
Apply moisture protection
tape to the underside
of the benchtop.
IMPORTANT!
To prevent possible steam damage to the cabinetry, ensure that any bare wood surrounding
the dishwasher is sealed with an oil-based paint or moisture-proof polyurethane.
1
3
4
2
Back foot of the
dishwasher can be
adjusted by using
a 6mm Allen key
(not supplied)
Front feet of
dishwasher can
be adjusted as
shown
4
9
Installation instructions
Front panel material specifications
The front of the dis
●
hwasher can be fitted with a front panel with the following specifications:
Adequately sealed to withstand moisture (50°C @ 80% RH). Because of it being a hot and wet
●
environment generally, the back and sides of the panel should be completely sealed with a
waterproof vapor barrier (ie polyurethane) to prevent damage to the panel.
Custom door panel preparation
5
10
Attaching custom door panel
Installation instructions
Insert Ø3.5 x 13mm
screws through pilot
●
holes and attach the
small slider bracket
to panel.
●
C
●
lose the door of the
dishwasher, then hang
the custom panel onto
the front of the door.
2 mm
1
2
11
Installation instructions
Door balancing
●
IMPOR
●
TANT!
5
4
The door balance can be
adjusted via two screws
accessed through two
holes at the front.Adjust
both sides at the same
time, alternating between
the sides so that even
balance is achieved.
Adjust
●
these using the
SUPPLIED HEX KEY
ONLY
●
until the door just
remains open under its
own weight.
Open the door and remove
screws before replacing
them with Ø3.5 x 44mm
screws to fix panel into
place.
3
Adjust the placement of
the door to the correct
position.
12 mm
2 mm
[08] X4
(3.5x44
m m)
12
Installation instructions
Slide toe kick firmly into
●
the spaces on either side
of the chasis to attach.
●
Fix brackets to panel using Ø3.5 x 13mm
screws. Insert toekick into product and
mark the desired alignment depth on
the bracket. Remove panel. Using a
screwdriver, bend the marked tabs out
on both brackets to prevent toekick from
receding into product further.
153
65
30
100
A
toekick depth range
4
Mark out the pilot hole locations for each
bracket. To establish the height in which
the bracket will be fixed, measure the
distance from the floor to the lowest hole
of the bracket. Remove bracket from the
product and plot the location of the other
holes relative to this measurement. Note
door overhang and swing range.
1
2
Toe kick installation
A
180.9 Centre
3
6
Separate panel
13
Installation instructions
F
●
it continuous panel to
surrounding cabinetry
Align the toekick to desired position and
mark out the point in which the toekick
meets the base of the door panel. Cut
back excess.
153
65
30
100
A
toekick depth range
3
Note door overhang and swing range
relative to height and depth of toekick
panel. As the panel is continuous, cutting
back panel is likely to be necessary to
ensure seamless integration.
1
Continuous panel
IMPORTANT!
Toe kick can protrude no more than
90mm out from the dishwasher to
ensure that the visibility of the floor
light is not obstructed.
2
14
Installation instructions
Securing product
7
A Secure to the cabinetry on the sides
Secure product to cabinetry
●
through on both sides of
the chasis using Ø4 x 25mm
screws.
●
B
15
Installation instructions
Optionally secure to the cabinetry above
Secur
●
e product to the bench
through top of the chasis
using Ø4 x 25mm screws.
16
Installation instructions
Plumbing and drainage options. Determine which is
more suitable
●
If space is limited
●
for fixing, push
hose through drain
●
hose support
to required height
●
min. radius
●
200 mm
min. 750 mm
step 9
Dishwasher and Ø 38 mm Standpipe
38mm
8
17
Installation instructions
If space is limited
●
for fixing, push
hose through drain
hose support
to required height
Dishwasher using drain hose joiner
onto sink trap/waste tee
min. 500 mm
●
min. radius
200 mm
step 9
Installer to provide
drain hose joiner to suit
min. 15mm waste tee
Ensure drain hose is routed
●
straight to joiner. Remove excess
drain hose material if necessary.
●
Do not shorten the inlet hose.
IMPORTANT!
Do not connect the drain hoses
to a Waste Disposal Unit, as this
type of connection may lead to a
blockage in the drain hoses.
750-882.5 mm
750 - 882.5 mm
18
Ensure the supplied rubber
●
washer is fitted inside the
coupling. Tighten coupling
with spanner.
180o
No leaks!
12
Plumbing -- Wa
●
ter inlet connection
IMPORTANT!
The appliance
●
should be connected to the water main using the new water
inlet hose supplied.Old hoses should not be used.
●
Do not shorten the inlet hose.
1.Take note of water connection requirements.
The dishwasher has a single valve water connection.
We recommend a cold water connection for best performance and energy efficiency.
The incoming water temperature should not exceed 25oC.
2.Take note of the permitted water pressure extremes.
Lowest: 0.4 bar = 4 N/cm2 = 40kPa
Where pressure is below 1 bar, contact a qualified plumber.
Highest: 10 bar = 100 N/cm2 = 1MPa
Where pressure is above 10 bar, a pressure reduction valve must be installed.
●
Contact a qualified plumber.
3.Connect the water inlet hose to an accessible water tap with a 3/4” BSP connector.
Ensure that there is no kink in the inlet hose that could restrict the flow of water. A
90o bend requires a minimum height of 200mm for a kink-free curve.
Ensure incoming water is clear. If the water pipes have not been used for a long
period of time, let the water run to make sure it is clear with no impurities. Not
doing so may result in the water inlet hose getting blocked and damaging the appliance.
If required, use a filter insert to filter out deposits from the piping. The filter insert is
available from your Authorised Service Centre or Customer Care.
4.Tighten the hose coupling a further half turn after seal contact.
5.Check that the connection does not leak.
min.
10mm
3/4” BSP connector
Connect inlet hose to cold water
Installation instructions
9
19
Plug product in
Electrical connection
●
The dishwasher must not be connected to the electrical supply while installation is
being carried out. Ensure all domestic wiring is properly earthed.
Check the rating label (located on the left-hand side of the dishwashers stainless
steel inner door) and ensure that the voltage and frequency values for the current
●
in the house correspond to those on the rating label.
Insert the plug into a properly earthed power outlet that has a disconnection switch.
●
IMPORTANT!
The earthing of the appliance is a safety requirement mandated by law.
If the power cord is not long enough to reach the outlet or the outlet to which the
●
appliance must be connected is not appropriate for the plug, the entire dishwasher
power cord must be replaced. This should only be done by a Haier authorised technician.
Do not modify or cut the plug. Do not use an adaptor, extension cord, or multi-outlet
●
power board to connect the dishwasher to the power supply, as these could cause
overheating and create a fire hazard.
The outlet into which the dishwasher is plugged must remain easily accessible(e.g.
in an adjacent cabinet) even when the appliance is installed. This is to ensure that the
dishwasher can be disconnected from the power supply for safe cleaning and
maintenance.
Installation instructions
10
20
Final checklist
To be completed by the installer
Check all parts are installed.
Ensure that all panels and parts thereof are secure and final electrical tests have
been conducted in accordance with local electrical regulations.
●
Check that the dishwasher is level. If necessary, adjust the levelling feet slightly.
To ensure optimum performance, the dishwasher should not be inclined more than
1o. Check with a spirit level.
Ensure inlet hose to water supply has supplied rubber washer fitted, and that its
tightened a further half turn after seal contact.
Ensure any knockouts or plugs in drain connection have been drilled out and drain
connection has been made.
The drain hose joiner must not support the weight of excess hose material. Keep
drain hose as fully extended as possible to prevent sagging. Any excess length of
drain hose should be kept on the dishwasher side of the highloop.
If connecting the drain hose to the sink trap, ensure the Highloop is a minimum
●
150mm higher than the drain hose joiner.
Ensure any packaging or tape securing the racks is removed from the dishwasher.
●
Check that the door opens and closes freely without resistance to adjacent cabinetry.
Check that the electrical outlet is accessible and located in an adjacent cupboard.
Check the operation of the dishwasher:
If a fault code appears, see the Fault codes section of the User guide for advice.
Installation instructions
21
Product Description
1.
8.
●
Detergent dispenser
2.
9.
Rating label
3.
Lower basket
●
4.
Filters
10.
11.
Salt container
Cutlery basket
5.
6.
Rinse aid dispenser
7.
Upper basket
Utensil tray
Upper spray arm
Lower spray arm
22
Overview of programmes
Time & Inf
●
o display
During any selection the display shows by scrolling related information like:
Programme c
●
ycle time
Programme start delay time
Error codes
●
and service information
After start of an operation it displays without scrolling:
●
Remaining time in hours of a delayed programme starts, e.g.
Remaining programme cycle time in minutes, e.g.130
While running it may vary due to local conditions and daily working load.
124 5
10
8
79
36
1. ON / OFF button
PROGRAMME SELECT button
START DELAY button
Additional function button
Lack Salt and Rinse Aid reset button
START / PAUSE button
3.
5.
4.
6.
2.
7. Time & Info Display
Speed Up function Indicator
Dry function Indicator
1/2 function Indicator
9.
10.
8.
1)
1) Additional function button permit to activate Exp function or Multi-tab function. Pressing consecutively this
button the correspondent functions are activated. Activation is confirmed by the correspondent indicator.
2) Adding express function, it can be used with P1(ECO), P2, P3 and P7.
3) Adding dry function, it can be used with P1(ECO), P2, P3, P5, P6, P7 and P8.
4) 1/2 function, it can be used with P1(ECO), P2, P3, P6 and P7.
23
Overview of programs
1) Use this program to quickly rinse the dishes. This prevents the remaining food
to bond on the dishes
●
and bad odours to come out from the appliance. Do not use
detergent with this program!
●
3) Program for normally soiled tablew
●
are (the most efficient in terms of its
combined energy and water consumption for that type of tableware). Program
standardised to EN 50242
●
4) The values given for programs other than the eco program are indicative only.
Programs
Programs Type of food residue Type of load
Intensive
70°C 130min
Rapid
45°C 32min
Prewash
45°C 20min
Universal
60°C 115min
Total Care
45°C 98min
Special
45°C 72min
ECO
50°C 298min
P1
P2
P3
P4
P5
P6
P7
1)
Auto Care
45-70°C 148min
P8
2) The appliance senses the type of soil and the quantity of items in the baskets. It
automatically adjusts the temperature and quantity of water, energy consumption
and program duration.
2)
24
To ensure good washing results,the dishwasher requires soft water.Hard water can
be detrimental to the performance of your dishwasher. Over time,glassware washed
in hard water will become opaque and dishes will become spotted or covered in a
white film. Using very hard water can cause dishwasher parts to fail over time.Salt
can improve the situation.
The amount of salt dispensed can be set in S1 and S6 stages,depending on the
●
hardness of your wate
●
r.
1.Find out about the hardness value of your tap water.Your water utility company
will help you with this.
2.Setting can be found in the water hardness table.
Adjusting the water softening system
Identify the local water hardness
Water softening system
* Remark
1) Factory default setting for powder de
●
tergent.
2) Recommended setting for combi det
●
egent tablets.
3) Indicator for Salt is off.
Water hardness
Water softener
adjustment
German
degrees(°dH)
French
degrees(°fH)
Mmol/l Clarke
degrees
electronic
31-50 55-89 5.5. -8.9 39-63 S6
17-30 30-54 3.0-5.4 21-38 S5
13-16 23-29 2.3-2.9 16-20 S4
9-12 16-22 1.6-2.2 11-15 S3
0-8 0-15 0-1.5 0-10 S2
- - - - S1
1) *
2) *
3) *
25
As soon as the low salt indicator is lit on the control panel ,salt should be topped
up.Always refill with special salt immediately before switching on the appliance.This
ensures that overrun special salt solution is immediately washed out and does not
corrode the rinsing tank.
Using special salt
Top up the salt as follows:
Water softening system
Only use dishwasher salt. Other products can cause damage to the appliance!
●
Any spilled salt causes corrosion.Run a programme after each refill.
1.Turn the cap clockwise to open the salt
●
container.
2.Fill with1 litre of water into the salt container.
3.Fill the tank up with specific salt(water
overflows).
4.Remove spilled salt from the opening area.
5.Turn the cap counter-clockwise to close
the salt container.
CAUTION
6.Press button for 3 sec after each
refill to reset salt aid indicator.
26
Adjusting the rinse aid dosage
●
The normal, factory-set dosage level is R3, but you may need to adjust this to suit
your water conditions.
If there is excessive foaming at the end of the wash,reduce the dosage.
●
If you live in a hard water area or if dishes are wet or streaky after drying,
increase the dosage.
To adjust the rinse aid setting:
If you are using tablets with built-in rinse aid, we recommend setting the rinse
aid dosage level to off (R1).
How to refill the rinse aid dis
●
penser
1.Pull the button to snap the dispenser cover open.
2.Pour rinse aid into the circular opening, making sure not to fill beyond the MAX
●
marking.
IMPORTANT!
Take care not to spill rinse aid into the dishwasher.Any spills must be wiped up
to prevent excess foaming. Failure to do so may result in a service call, which
will not be covered by warranty.
●
3.Close the cover, making sure it clicks shut.
4.Press and hold the button for 3 sec after each refill to reset rinse aid indicator.
Dosage regulator
When to refill the rinse aid dispenser
When rinse aid level becomes low,the digtial will
scrolling display RINSE AID to remind you to
refill the dispensers.
Using rinse aid
We highly recommend using liquid rinse aid regularly to get the best drying
results.Rinse aid gives a streak-free, sparkling clean look to glass and chinaware.
In addition, it prevents metal from tarnishing.
27
Utensils
Never put highly absorbent materials, such as sponges and towels in your
●
dishwasher.Do not put dishes or cutlery that have been soiled by tobacco
ash, wax, lubricating grease or paint in your dishwasher.
IMPORTANT!
Cutlery and silverware
All cutlery and silverware should be rinsed immediately after use to prevent tarnishing
caused by some foods. Silver items should not come into contact with stainless steel,
e.g. other cutlery. Mixing these items can cause staining. Remove silver cutlery from
●
the dishwasher and hand dry immediately after the programme has finished.
Aluminium
Aluminium can be dulled by dishwasher detergent. The degree of change depends on
the quality of the item.
●
Other metals
Iron and cast iron objects can rust and stain other items. Copper, pewter and brass
●
tend to stain. Wash these items by hand.
Woodware
Wooden items are generally sensitive to heat and water. Regular use in the
dishwasher may cause deterioration over time. If in doubt, wash by hand.
Glassware
Most everyday glassware is dishwasher safe. Crystal, very fine and antique
glassware may etch that is, become opaque. You may prefer to wash these items by
hand.
Plastic
Some plastic may change shape or colour with hot water. Check the manufacturers
instructions about washing plastic items. Washable plastic items should be weighted
●
down so they do not flip over and fill with water or fall through the basket during the
wash.
Decorated items
Most modern china patterns are dishwasher safe. Antique items, those with a pattern
painted over the glaze, gold rims or hand-painted china may be more sensitive to
machine washing. If in doubt, wash by hand
Glued items
Certain adhesives are softened or dissolved in machine washing. If in doubt, wash by
hand.
28
Loading utensils
IMPORTANT!
Upper rack
The upper rack is designed to hold items like glasses, cups, saucers, plates and
shallow pans.
The upper rack may be adjusted to accommodate larger items. You can adjust the
height of the upper basket to create more space for tall items in the lower basket.
The upper rack may be adjusted to accommodate larger items. Place small items
on the foldable cup holder.
If the tableware or cookware rack is burnt, scorched,sticky, and other food which
is very difficult to removed, it is advisable to soak it for a period of time before
washing it or pre-dispose it with a dish cloth or else it will be hard to clean.Remove
any large food particles before placing dishes in the dishwasher. It is not necessary
to prerinse utensils under running water.
Place sharp and
●
pointed
items with the blade pointing
downward into the knife
rack, to keep them out of
harms way.
29
Loading utensils
Place the largest items here: pots,
●
pans, lids, serving dishes and bowls.
Fold down the tines to place pots
●
and pans flat on the bottom.
Ensure dishware items do not block
the spray arm above from rotating.
If you need more height for tall items,
you can raise the upper basket. See
instructions on previous pages.
Lower rack
To adjust the upper rack:
1.Fully extend the upper rack and rotate open the two plastic end caps on the front
of the rails.
2.Remove the upper rack.
3.Select the set of rollers on the side of the rack that provides the desired height, and
reinstall the upper rack by guiding the rack rails between the appropriate set of rollers.
4.With the rack reinstalled, rotate closed the two plastic end caps, ensuring the snap is
properly engaged. Failure to properly engage the end caps may result in the rack falling
from the dishwasher.
End Cap
Rollers
Rail
Remove:
Rail
End
Cap
Replace:
Rollers
IMPORTANT!
Before you adjust its height,make sure the basket is empty.
30
Loading utensils
Cutlery basket
Put sharp and pointed items with the blad
●
e pointing downward to keep them out of
harms way.
Mix spoons with other cutlery
to prevent them to bond
together.
Use the grid element in order
to separate the cutlery.
Place Cutlery with the
handles down for better
washing results.
If long items may block the
spray arms find a horizontal
positioning in the upper
basket.
CAUTION
31
How to make savings
Tips on how to save money and not damage the environment when using
your appliance.
Achieve the best use of energy, water, detergent and time by using the
●
recommended maximum load size. Save up to 50% energy by washing a full
load instead of 2 half loads.
If you want the dishwasher to give a complete wash, place the dishes in the
dishwasher at the end of each meal and if necessary turn on the COLD RINSE
cycle to soften the food remains and remove bigger particles of food from the new
load of dishes. When the dishwasher is full start the complete wash cycle
programme.
If the dishes are not very dirty or if the baskets are not very full select an
ECONOMY programme, following the instructions in the program list.
The most efficient programmes in terms of combined use of water and energy are
usually the longer-lasting ones with lower temperature.
32
Adding detergent
IMPORTANT!
Only use detergents recommended for automatic dishwashers.
Dishwasher de
●
tergents are strongly alkaline. They can be extremely dangerous if
swallowed. Avoid contact with the skin and eyes and keep children and infirm
persons away from the dishwasher when it is open. Check that the detergent
dispenser is empty after completion of each wash programme.
Never sprinkle or pour detergent directly onto any item in the dishwasher. Detergent
and dishwasher tablets should not be in direct contact with dishes or cutlery.
Do not use hand washing liquids, soap, laundry detergents or disinfectants, as
these will damage the dishwasher.
Filling the detergent dispenser
1.Press the button on the left of the dispenser.
IMPORTANT!
Approach the dispenser from the right-hand side to prevent the cover from snapping
open on your hand.
2.Add detergent into the appropriate compartment(s). The ‘15’ and ‘25’
markings in the
main wash compartment correspond to grams of powdered detergent.
IMPORTANT!
Tablets should only be placed in the main wash (larger) compartment.
3.Remove any excess detergent from the edges of the dispenser.
4.Close the cover and press down until it clicks shut. The detergent will automatically
be released into the dishwasher during the wash programme.
Open the
cover here
wash compartment
●
33
Before first Use
5.The display shows the current level of R
●
inse Aid after 5 seconds. The level setting
is from R1-R4, and the default is R3.Pres
●
s the additional function key to set the
level backward:R3-R2-R1-R4-R3-R2.Press the Salt / Rinse reset key to set the
level forward:R3-R4-R1-R2-R3-R4.Press the program selection key to save the
current level and enter the Memo setting.Or press and hold the power key for 3S
to save the settings and enter the program selection state.
4.The display shows BUZZER, and displays YES after 5S. The default is YES.Press the
Salt / Rinse reset key to set to NO.Press the program selection key to save
the current level and enter the Rinse Aid setting.Or press and hold the power key
for 3S to save the settings and enter the program selection status.
How to Adjust User Preference Settings
During the selection of programmes, press and hold the program selection key
for 5S to enter the user setting mode.User setting mode includes Language setting,
Water Softener setting, Buzzer setting,Rinse Aid setting and Memo Mode setting.
1.The appliance is switched on.
2. Press the program selection key to enter the Language setting menu, and the
display will show the current language.Press to move backward and
to move forward between the 25 languages.Press the program selection key
again to save the current selection language and enter the Water Softener setting
menu.Or press the power key for 3S to save the settings and enter the program
selection state.
6.The digital tube will scroll to display the MEMO FUNCTION, and displays NO after
5S.Press the Salt / Rinse reset key to switch between YES and NO.Press the
program selection key to save the current level and enter the Language setting.
●
Press and hold the power key for 3S to save the settings and enter the program
●
selection state.
3. The current water hardness level will be displayed after the display shows
SOFTENER 5S. The default level is S4. The level setting is from S1 to S6.Press the
additional function key to set the level backward: S3-S2-S1-S6-S5-S4-S3.
Press the Salt / Rinse reset key to set the level forward S4-S5-S6-S1-S2-S3-S4.
Press the program selection key to save the current level and enter the Buzzer
setting.Or press and hold the power key for 3S to save the settings and enter the
program selection state.
34
Daily Use
1. Open the door and Press the ON/OFF button to turn the dishwasher on.
●
3. Press to start the programme and c
●
lose the door.
2. Press to select the program you want on the dishwasher control panel.
NOTICE
Start a Programme
If the MEMO MODE YES The appliance remembers the last programme
you used. The next time the appliance will switch on, the appliance pre-selects
the programme last used.
Set a start time by the following procedure
●
in order to delay a programme start:
1.Set a programme.
●
2.Press the reservation button .
3.Press the STA
●
RT/PAUSE button and close the door.
Start a Programme with Delay
Pause and restart a wash programme
1. Open the door carefuly to pause the programme.The digital scrolling display
PAUSE and the pause beep will sound while the dishwasher is paused.
NOTICE
There is a risk of being sprayed with hot water,do not fully open the door until
the spray arms have stopped rotating.
2.Load,remove,or rearrange any dishes if needed.
3.Close the door to restart the programme.
Cancel or change a wash programme
Open the door carefully to pause the programme.Press and hold 3 sec,
Washing program reset.And then you can choice a new wash programme to start.
The display shows the countdown of the start delay. The countdown decreases
with steps of 1 minute.
When the countdown is completed, the programme starts.
35
Daily Use
If a programme
●
will be aborted in the process of washing dishes, the residue of
detergent remains on the dishes. These can cause damage to health! Make sure to
rinse off the detergent residues completely before using these dishes again.
If the door will be
●
opened immediately after the end of programme, hot steam can
escape. Danger of scalding!Open the do
●
or carefully!
When the programme is completed, an accoustic signal is heard (if it is not switc hed
off).The d isplay switches off.
1.Press to switch off the appliance or the appliance switches into standby mode
automatically after 30 seconds.
2. Open the door.
3. Remove dishes:
●
Open the door slightly and leave it ajar (about 100 mm) to help the drying
process.
Let the dishes become cold before removing them from the appliance. Hot
dishes damage more easily.
First remove the items from the lower
●
basket, then from the upper basket.
CAUTION
CAUTION
Cancel a Delayed Start
End of Programme
Press the button to cancel the reservation.
Cancel Start Delay / Programme
1. Press the , the start delay is cancelled.
Press the for about 3 second, the programme is aborted.
2. Start a new programme and a delayed start if desired.
36
Care and cleaning
Over time, food
●
residue or limescale deposits may accumulate inside your
dishwasher.These may reduce efficiency, and food residue may produce a bad
odour. Inspect and clean your dishwasher regularly.
To clean exterior
●
surfaces of the dishwasher, wipe with a clean, soft damp cloth
and dry with a clean, lint-free cloth.
For non-flush surfaces wipe along or around the surface. For example, to wipe
down the exterior control buttons, use a circular wiping motion around the button.
Take care not to cause excessive wetting of the control panel area.
●
Note: before cleaning the control panel, it is useful to disable the buttons by
activating Keylock.
Clean thoroughly with warm water on a soft, lint-free cloth. If the interior is heavily
soiled, use a di
●
shwasher cleaner/descaler following the manufacturer’s instructions.
The filters prevent larger food particles in the wash water from reaching the pump.
●
These particles may occasionally block the filters. We recommend cleaning the
filters whenever there is evidence of food particles.
Cleaning the dishwasher exterior
Cleaning the door seal and dishwasher interior
IMPORTANT !
Before any cleaning or maintenance, always disconnect the dishwasher from the
power supply, turn off the water supply, and wait until all parts of the dishwasher
have cooled.
Do not use the following cleaning aids, as they may damage the surfaces:
-plastic or stainless steel scouring pads
-abrasive, solvent, household cleaners
-acid or alkaline cleaners
-laundry detergents or disinfectants
-stainless steel cleaners or polishes
-hand-washing liquids or soap
Where there is broken crockery or glass in the dishwasher, it must be carefully
removed to prevent personal injury or damage to the appliance.
After cleaning, always check that the spray arms and filters are all correctly in
place.
37
Care and cleaning
To remove the drain
●
filter, turn the filter anti-clockwise to release, then lift out.
Once the drain filter has been removed you can lift the filter plate out.
Rinse them thoroughly under running water and then replace.
Replace the filters correctly after cleaning, making sure the filter plate is flush with
the dishwasher base.
IMPORTANT !
When cleaning the underside of the filter plate, take care handling its sharp outer
edge.
Cleaning the spray arms
●
Limescale and f
●
ood particles in the wash water can block the holes in the spray
arms and the arm mountings. Clean these parts about once a month, or more often
should the need arise.
Drain filter
Filter plate
38
Care and cleaning
Cleaning the upper spray arm
To remove the upper spray arm, carefully unscrew its locking nut.
Rinse the spray arm thoroughly under running water, then refit.
IMPORTANT !
Make sure you twist the locking nut on the upper spray arm firmly back on the
water supply tube.Check that the upper spray arm is firmly locked in place and
rotates freely.
Cleaning the lower spray arm
●
To remove the lower spray arm, simply lift the spray arm off its mounting.
Rinse the spr
●
ay arm thoroughly under running water, then refit it on its mounting.
Low
●
er spray arm
Upper spray arm
Locking nut
Water supply tube
39
Troubleshooting
Before maintenance, deactivate the appl
●
iance and disconnect the mains plug from
the mains socket.
Electrical equipment should be serviced only by qualified electrical experts,
because improper repairs can cause con
●
siderable consequential damages.
Many occuring problems could be solved by yourself without specific expertise. In
case of a problem please check all shown possibilities and follow below instructions
before you contact an after sales service.
The appliance does not start, or it stops during operation or Indicator is lighted
Problem Possible cause Possible solution
The programme
does not start.
Appliance door is open. Close the appliance door.
Delay start is set. Refer to displayed time.
Mains plug is not connected
in the mains socket.
●
Connect the mains plug.
Fuse in the house circuit is
●
damaged. Replace the fuse.
Display shows
Rinse Aid
Rinse aid dispenser is empty. Refill Rinse aid until full.
R
●
efill of rinse aid was not
confirmed.
CAUTION
Display shows
Salt
Softener salt is empty. Fill the tank up with specific
salt until full.
Refill of salt was not
confirmed.
Press button for 3 sec
after each refill.
Press button for 3 sec
after each refill.
40
Troubleshooting
Problem Possible cause Possible solution
Water tap is closed.
Open the water tap.
Note: Whenever Error is
s o l v e d s w i t c h o f f t h e
appliance and restart the
programm.
W
●
ater inlet hose has a kink or
a bend.
Make sure that the position of
the hose is correct.
In case of aqua-stop system:
water protection is triggered;
the marker (C) is red.
The hose must be replaced.
Filter in the water inlet hose
is clogged.
Clean the filter at the inlet
hose connections at tap and
the rear of the appliance.
Water inlet is clogged. Check water flow from tap.
W
●
ater pressure is too low. Contact your local water
authority.
Anti- flood device is on:
There are water leakages in
●
the appliance.
●
The water inlet valve is
open and blocked.
The drainage is blocked.
1.Close the water tap.
2.Disconnect appliance from
power supply.
3.Contact Service.
Error codes on the display
All other Alarmcodes:
1. Note Alarmcode
2. Contact Service ; refer to CUSTOMER SERVICE
Acoustic alarm,
display shows
ALARMCODE E10
The appliance does
not fill with water.
Acoustic alarm,
display shows
ALARMCODE E30
Leak: The drainpump
runs permanently!
41
Troubleshooting
Problem Possible cause Possible solution
The dishes are not
●
clean.
Filters are clogged. Clean the filters.
F i l ter s a r e n o t correct l y
assembled and installed.
Make sure that the filters
are correctly assembled and
installed.
Spray arms are clogged.
Re m o v e r e m ain i n g f o o d
remnants with a thin pointed
object.
Programme was not
applicable for the type of load
and food remnants.
programme is applicable for
the type of load and food
remnants.
Incorrect position of the items
in the baskets. Water could
not wash all items.
Make sure that the position
of the items in the baskets is
correct and that the water can
easily wash all items.
S
●
pray arms could not turn
freel
●
y.
Make sure that the position
of the items in the baskets is
correct and does not cause
the blockage of the spray
arms.
No detergent or insufficient
quantity of detergent in the
detergent dispense
●
r.
Make sure that you add the
correct quantity detergent in
the dispenser before you start
a programme.
The wash cycle was
interrupted by a long break.
Do not open the door or cut
power supply during the wash
cycle.
Whitish streaks,
s t a i n s o r b l u i s h
layers on glasses
and dishes.
Released quantity of rinse aid
is too much.
D e c r e a s e t h e r e l e a s e d
quantity of rinse aid.
Quantity of detergent was too
much.
Make sure that you add the
correct quantity of detergent
in the dispenser before you
start a programme.
Mu
●
ltitab detergent tablets
used with a short programme
might not fully dissolve.
Select a longer programme
when using Multitab detergent
tablets.
Washing Results are not satisfactory
Make sure that the
42
Troubleshooting
Problem Possible cause Possible solution
Dry water drop
stains on glasses
and dishes.
Rinse aid dosage is too low. Increase the released quantity
of rinse aid.
Q u a l i t y o f r i n s e a i d o r
Multitab.stains on glasses
●
Cleaning product too old;
change the product.
The dishes are wet.
drying
phase.
low
phase.
Open the door slightly and
leave it ajar (about 100 )
to help the drying process.
The dishes are
Rinse aid dispenser y.
R e f i l l r i n s e a i d i n t o t h e
dispenser and reset the rinse
aid indicator.
Quality of rinse aid or Multitab. Cleaning product too old;
change the product.
43
Suppliers name or trade mark
●
Hoover
Supplier´s model identifier
-place settings
Power consumption (Po)
●
in left-off mode in W
Rated capacity in standard
Energy consumption (Et) of the
standard cleaning cycle in kWh
Energy efficiency class 1)
Annual energy consumption
(AEc) in kWh/year 2)
Annual water consumption
●
(AWc) in liter/year 3)
Drying efficiency class 4)
●
Standard programme
(standard cleaning cycle) 5)
Programme time for the stan-
dard cleaning cycle in minutes
Duration of the left-on
mode (Tl) in minutes
Airborne acoustical noise
●
emissions in dB(A) re 1pW
Mounting / optional mounting
1) A+++ (highest efficiency) to D (lowest efficiency).
2) Energy consumption is based on the standard cleaning cycle (280 per year) using
cold water fill and the consumption of the lower modes. Actual energy consumption
will depend on how the appliance is used.
3) Water consumption in litres per year, based on 280 standard cleaning cycles.
Actual water consumption will depend on how the appliance is used.
4) A (highest efficiency) to G (lowest efficiency).
5) This programme is suitable to clean normally dirtied tableware and it is the most
efficient programme in terms of its combined energy and water consumption for that
type of tableware.
Total absorbed power
Colour
13A
220-240V/50Hz
1720-2050 W
BI Full-integrated
Silver
211
10
A++
0.75
0.5
2520
A
ECO
298
1
47
Maximum current intensity(A)
Mains water pressure
Power voltage
0.04-1 MPa (= 0.4-10 bar)
Technical Data
HDIH 2T1047-80
Power consumption (Pl)
in left-on mode in W 2.5
HMIH 2T1047-80
0120503693