Hoover HLSI 762GTWIFI-8 User Manual
Displayed below is the user manual for HLSI 762GTWIFI-8 by Hoover which is a product in the Dishwashers category. This manual has pages.
Related Manuals
User instructions
EN
HLSI 762GT WIFI
DISHWASHER
®
3
CONTENTS
General safety rules
Water connection
Loading the salt
Adjusting the upper basket
Loading the dishes
Information for test laboratories
Loading the detergent
Types of detergent
Loading the rinse aid
Cleaning the filters
Some practical hints
Routine cleaning and maintenance
Description of the control panel
Technical data
Programme selection and special functions
Water softener unit
Programme guide
Wizard
Identifying minor faults
Your guarantee
Please read the instructions in this booklet carefully because they contain important
information on how to install, use and maintain your dishwasher safely as well as
containing useful tips on how to make the most of it.
Keep this booklet safe for future reference.
Fig. A
32
1
4
5
pag. 4
pag. 7
pag. 9
pag. 10
pag. 11
pag. 13
pag. 14
pag. 15
pag. 16
pag. 17
pag. 18
pag. 19
pag. 20
pag. 20
pag. 21
pag. 25
pag. 26
pag. 28
pag. 30
pag. 32
4
GENERAL SAFETY RULES
■This appliances is intended to be
used in household and similar
applications such as:
- staff kitchen areas in shops,
offices and other working
environments;
- farm houses;
- by clients in hotels, motels
and other residential type
environments;
- bed and breakfast type
environments.
A different use of this appliance
from household environment or
from typical housekeeping
functions, as commercial use by
expert or trained users, is
excluded even in the above
applications.
If the appliance is used in a
manner inconsistent with this
it may reduce the life of the
appliance and may void the
manufacturer’s warranty.
Any damage to the appliance or
other damage or loss arising
through use that is not consistent
with domestic or household use
(even if located in a domestic or
household environment) shall not
be accepted by the manufacturer
to the fullest extent permitted by
law.
■This appliance can be used by
children aged from 8 years and
above and persons with reduced
physical, sensory or mental
capabilities or lack of experience
and knowledge if they have been
given supervision or instruction
concerning use of the appliance in
a safe way and understand the
hazards involved.
Children shall not play with the
appliance. Cleaning and user
maintenance shall not be made
by children without supervision.
■Children should be supervised to
ensure that they do not play with
the appliance.
■Children of less than 3 years
should be kept away unless
continuously supervised.
■Should it be necessary to replace
the supply cord, call the After
Sales Service Centre.
■The appliance must be connected
to the water mains using new
hose-sets. The old hose-sets
should not be reused.
■Water pressure must be between
0,08 MPa and 0,8 MPa.
■When the appliance is located on
a carpet floor, attention must be
paid to ensure that there is no
obstruction to the bottom vents.
■After installation, the appliance
must be positioned so that the
plug is accessible.
5
■For the maximum place loading,
please refer to the "TECHNICAL
DATA" table/section.
WARNING !
Knives and other utensils with
sharp points must be loaded
in the basket with their points
down or placed in a horizontal
position.
■The door should not be left in the
open position since this could pre-
sent a potential hazard ( es. trip-
ping ).
■To consult the product fiche plea-
se refer to the manufacturer web-
site.
Safety instructions
■Make sure the electrical system
is grounded. Otherwise, seek
qualified professional assistance.
Manufacturer declines all
responsibility for any damage
due to non-earthing of the
machine.
■Ensure that the dishwasher does
not crush power cables.
■In general it is not advisable to use
adaptors, multiple plugs and/or
extension cables.
■Do not remove the plug from the
mains supply socket by pulling the
mains cable or the machine itself.
■Do not leave the appliance expo-
sed to the elements (rain, sun etc).
■Leaning or sitting on the open
door of the dishwasher could
cause it to tip over.
■The dishwasher is designed for
normal kitchen utensils.
Objects that have been contami-
ned by petrol, paint, traces of steel
or iron, corrosive chemicals, acids
or alkalis must not be washed in
the dishwasher.
■If there is a water softening device
installed in the home there is no
need to add salt to the water sof-
tener fitted in the dishwasher.
■If the appliance breaks down or
stops working properly, switch it
off, turn off the water supply and
do not tamper with it. Repair work
should only be carried out by an
approved service agent and only
genuine spare parts should be fit-
ted. Any failure to follow the above
advice may have serious conse-
quences for the safety of the
appliance.
■If it you need to move the machi-
ne after removing the packaging,
do not try to lift it by the bottom of
the door.
Open the door slightly and lift the
machine by holding on the top.
■For the installation of built-in
appliances, please refer to the
specific chapter or to the instruc-
tions enclosed with the booklet.
Appliance complies with
European Directives:
■2006/95/EC (LVD);
■2004/108/EC (EMC);
■2009/125/EC (ErP);
■2011/65/EU (RoHS)
and subsequent amendments
6
WATER CONNECTION
IMPORTANT
The appliance must be connected to
the water mains using new hose-sets.
The old hose-sets should not be reused.
■The inlet and drain hoses can be directed
to left or right.
IMPORTANT
The dishwasher can be connected to
either cold or hot water, as long as it
is no hotter than 60°C.
■Water pressure must be between
0,08 MPa and 0,8 MPa.
■The inlet hose must be connected to a
tap so that the water supply can be cut
off when the machine is not in use
(fig. 1 B).
■The dishwasher is fitted with 3/4" threaded
connector (fig. 2).
■Connect inlet hose “A” to water tap “B”
with a 3/4" attachment making sure that
it has been properly tightened.
■If it is necessary, the inlet pipe can be
lengthened up to 2,5 m. The extension
pipe is available from the After Sales
Service Centre.
■If the dishwasher is connected to new
pipes or to pipes which have not been in
use for a long time run water through for
a few minutes before connecting the
inlet hose. In this way no deposits of
sand or rust will clog up the water inflow
filter.
1
2
7
8
Connecting the outlet hose
■The outlet hose should disharge into a
standpipe, making sure that there are no
kinks (fig. 4).
■The standpipe must be at least 40 cm
above floor level and it must have an
internal diameter of at least 4 cm.
■It is advisable to fit an anti-odour air trap
(fig. 4X).
■If necessary the outlet hose can be
extended up to 2,5 m, provided that it is
kept at a maximum height of 85 cm
above floor level. The extension pipe is
available from the After Sales Service
Centre.
■The hose can be hooked over the side of
the sink, but it must not be immersed in
water, in order to prevent water from
being syphoned back to the machine
when this is in operation (fig. 4Y).
■When installing the appliance under a
worktop the hose pipe clamp must be
attached to the wall in the highest possible
position under the worktop (fig. 4Z).
■Check that there are no kinks in the inlet
and outlet hoses.
4
9
LOADING THE SALT
■The appearance of white stains on dishes
is generally a warning sign that the salt
container needs filling.
■On the bottom of the machine there is a
container for the salt for regenerating
the softener.
■It is important to use only a salt that is
specifically designed for dishwasher.
Other types of salt contain small quantities
of insoluble particles which over a long
period of time may affect and deteriorate
the softener performance.
■To add salt, unscrew the cap of the con-
tainer on the bottom and then refill the
container.
■During this operation a little water will
overflow; but keep adding salt until the
container is full. When the container is
full, clean the thread of salt residue and
retighten the tap.
■After loading the salt, it is recommended
running a complete washing cycle,
or COLD RINSE programme. The salt
IMPORTANT
After loading the salt, YOU
MUST run a complete washing
cycle, or the PRE-WASH/COLD
RINSE/REFRESH programme.
■The salt dispenser has a capacity of
between 1.5 and 1.8 kg and, for efficient
use of the appliance, it should be refilled
from time to time according to the
regulation of the water softener unit.
IMPORTANT
(Only for first start up)
When the appliance is used for the
first time, after completely filling the
salt container, it is necessary to add
water until the container overflows.
10
1
3
a
b
a
b
2
ADJUSTMENT OF THE
UPPER BASKET
If 29 cm to 32,5 cm plates are normally
used, load them onto the lower basket after
the upper basket has been placed in its
upper position and proceed as detailed
below:
1. Pull out the upper basket;
2. Then grasp the basket from both sides
and lift it upwards (fig. 1).
Dishes that are bigger than 20 cm in
diameter can no longer be loaded onto the
upper basket and the mobile supports
cannot be used when the basket is in the
upper position.
ADJUST BASKET TO THE LOWER
POSITION:
1. Grasp the basket from both sides and lift
slightly upwards (fig. 2a);
2. Then slowly release into the correct
position (fig. 2b).
N. B. : NEVER LIFT OR LOWER THE
BASKET BY ONE SIDE ONLY (fig.3).
Attention :
it is advisable to adjust the basket before
loading the dishes.
11
LOADING DISHES
Using the upper basket
■The upper basket is provided with
mobile racks hooked to the sides of the
basket, which can be regulated into 4
positions.
■In the lowered position (A-A1) the racks
may be used for such items as: tea and
coffee cups, kitchen knives and ladles.
Also glasses with stems may be safely
hung on the ends of the racks.
■In the upright position (B-B1) the racks
allow you to load dinner plates and soup
plates. Plates should be loaded
vertically with the underside of the plate
towards the back of the dishwasher with
a space between each plate to allow
water to pass freely.
■It is advisable to load large plates
(approx. 26 or more cm) slightly tilted
towards the rear to facilitate introduction
of the basket into the machine.
■Salad bowls and plastic bowls may also
be loaded on the upper basket. It is
advisable to block these in place so that
the jets of water do not make them
overturn.
■The upper basket has been designed to
offer maximum flexibility in use and can
be loaded with up to 24 plates on two
rows, up to 30 glasses on five rows or a
mixed load.
A standard daily load is represented in
figs. 1, 2 and 3.
Upper basket (fig. 1)
A= soup plates
B= dinner plates
C= dessert plates
D= saucers
E= cups
F= glasses
Upper basket (fig. 2)
A= soup plates
B= dinner plates
C= dessert plates
D= saucers
E= cups
F= glasses with stems
G= glass
H= cutlery basket
BB1
AA1
A
B
C
D
E
F
AB
C
DEF
1
2
HF
G
12
Upper basket (fig. 3)
A= glasses
B= saucers
C= cups
D= small bowl
E= medium bowl
F= large bowl
G= dessert plate
H= serving spoons
I=
ladle
L= cutlery
Using the lower basket
■Saucepans, oven dishes, tureens, salad
bowls, lids, serving dishes, dinner
plates, soup plates and ladles can be
loaded on the lower basket.
■Place the cutlery in the plastic cutlery
holder with the handles pointing
upwards.
■Place the cutlery holder on the lower
basket (fig. 7 and 8), making sure that
the cutlery does not get in the way of the
rotating arms.
■The lower basket is fitted with a special
adjustable central rack (fig. 4 and 5).
This permits stable and optimum
loading, even when the size and/or
shape of the dishes is non-standard.
- POSITION “A”: for a standard load, or
one that excludes pans, salad bowls and
the like.
- POSITION “B”: for dishes which,
although standard size, have a particular
shape (very deep bowls, square dishes
or ones without borders etc.).
- POSITION “C”: for larger than average
flat plates and/or ones with non-
standard shapes (square, hexagonal,
oval, pizza dishes etc.).
■The small plates, as those used for
desserts for example, must be placed in
the lower basket as shown in the figure 6,
with the support flap placed outwards ("B").
For normal or large plates the flap must
be in the position ("A").
WARNING!
If the small plates are placed in the
basket with the support flap in the
incorrect position, the plates will
interfere with the lower spraying arm
preventing it to rotate.
4
5
A
C
A
B
6
AB
A
F
CC
G
L
E
DB
3
H
I
H
C
13
A standard daily load is represented in
figs. 7 and 8.
Lower basket (fig. 7)
A= medium-sized saucepan
B= large saucepan
C= frying pan
D= tureens, serving dishes
E= cutlery
F= oven dishes
G= medium bowl
H= small bowl
Lower basket (fig. 8)
A= soup plates
B= dinner plates
C= dessert plates
D= serving dish
E= cutlery
Please load the dishwasher sensibly to
ensure the best wash results.
IMPORTANT
The lower basket has a safety-stop
device, for its safe extraction, also
especially useful with a full load.
For loading salt, cleaning filter and for
ordinary maintenance, the complete
extraction of the basket is necessary.
INFORMATION FOR THE TEST
LABORATORIES
Please ask information required for
comparison testing and measuring noise
levels, according to EN normative, to the
following address:
testinfo-dishwasher@candy.it
In the request, please specify model name
and number of the dishwasher (see rating
plate).
D
F
BC
EH
G
7
A
D
A
E
C
B
8
C
14
LOADING THE DETERGENT
The detergent
IMPORTANT
It is essential to use a detergent
that is specifically designed for
dishwashers either in powder, liquid
or tablet form.
“FINISH” gives very good results and can
be easily obtained.
Unsuitable detergents (like those for
washing up by hand) do not contain the
proper ingredients for use in a dishwasher,
and stop the dishwasher from working
correctly.
Filling the detergent container
The detergent container is inside the door
(fig. A “2”). If the lid of the container is
closed, press the button (A) to open.
At the end of every wash cycle the lid is
always open and ready for the next time
the dishwasher is used.
WARNING!
When loading the lower basket, please
ensure that the plates or others do not
obstruct the detergent dispenser.
The amount of detergent to be used varies
according to how dirty the dishes are and
on the type of dishes to be washed.
We advise using 20÷30 g of detergent in the
wash section of detergent compartment (B).
After pouring the detergent into the container,
close the lid, firstly pushing (1) and then
pressing on it (2) until you hear the click.
Since not all detergents are the same the
instructions on the boxes of detergent can
vary. We should just like to remind users
that too little detergent does not clean the
dishes properly whilst too much detergent
will not produce better results and is also a
waste.
IMPORTANT
Do not use an excessive amount of
detergent and help limit damage to
the environment at the same time.
A
B
15
TYPES OF DETERGENT
Detergent tablets
Detergent tablets of different manufacturers
dissolve at different speeds, for this
reason, during short programmes, some
detergent tablets may be not fully effective,
because they are not completely dissolved.
If these products are used, is recommended
to choose longer programmes to guarantee
the complete use of the detergent.
IMPORTANT
To get satisfactory washing results,
the tablets MUST be placed in the
wash section of the detergent
container and NOT directly in the
tub.
Concentrated detergents
The concentrated detergents, with reduced
alkalinity and with natural enzymes, in
conjunction with 50°C wash programmes,
have a smaller impact on the environment
and they protect the dishes and the
dishwasher.
The 50°C wash programmes purposely
exploit the dirt-dissolving properties of the
enzymes, allowing therefore, with the use
of the concentrated detergents, to achieve
the same results of the 65°C programmes
but at a lower temperature.
Combined detergents
The detergents that also contain the rinse
aid must be placed in the wash section of
the detergent container. The rinse aid
container must be empty (if it is not empty,
set the rinse aid regulator to lowest position
before using combined detergents).
"ALL in 1" combined detergents
If you are planning to use “ALL in 1” (“3 in 1 “/
“4 in 1”/ “5 in 1”, etc.) combined detergents i.e.
those with built in salt and/or rinse agent,
we would advise the following:
■read carefully and follow the manufacturer’s
instructions given on the packaging;
■the effectiveness of detergents containing
the built in water softener/salt depends
on the hardness of your water supply.
Check that the hardness of your water
supply is within the effective range given
on the detergent packaging.
If when using this type of product, you
don't get satisfactory washing results,
please contact the detergent
manufacturer.
In certain circumstances use of combined
detergents can cause:
■limescale deposits on dishes or in the
dishwasher;
■a reduction in washing and drying
performance.
IMPORTANT
Any problems which arise as a direct
result of the use of these products
are not covered by our warranty.
Please note that using the "ALL in 1"
combined detergents, the rinse aid and
salt indicator lights (only used on
selected models) are superfluous, so you
must ignore the lights.
If washing and/or drying problems occur,
we recommend you return to use traditional
separate products (salt, detergent and
rinse agent). This will ensure that the water
softener in the dishwasher operates
correctly.
In this case, we recommends that you:
■refill both the salt and rinse aid container;
■run one normal washing cycle without a
load.
Please note that on return to the use of
conventional salt, a number of cycles will
be required before the system becomes
fully efficient again.
16
LOADING THE RINSE AID
The rinse aid
The rinse aid, which is automatically
released during the last rinsing cycle, helps
the dishes to dry quickly and prevents
spots and stains forming.
Filling the rinse aid container
The rinse aid container can be found to the
left of the detergent container (fig. A "3").
To open the lid, push the reference mark
and, in the same time, pull the tab of
opening.
It is always advisable to use rinse aid that
is specifically designed for dishwasher.
Check the rinse aid level through the
indicator eye (C) which is located on the
dispenser.
Regulating the rinse aid from 1 to 6
The regulator (D) is placed under the lid
and can be turned using a coin.
The recommended position is 4.
The limestone content of the water
considerably affects the formation of
limescale and the drying performance.
It is therefore important to regulate the
quantity of rinse aid to achieve good
washing results.
If, after the wash, streaks occur on the
dishes, decrease the amount by one
position. If whitish spots occur, increase the
amount by one position.
FULL EMPTY
dark light
C
D
1
2
3
CLEANING THE FILTERS
The filter system (fig.A “4”) consists of:
a central container that traps the larger
particles;
a flat gauze that continuously filters the
wash water;
a micro filter, located beneath the gauze,
that traps the tiniest particles ensuring a
perfect rinse.
■To achieve excellent results every time,
the filters should be checked and
cleaned after each wash.
■To remove the filter unit, simply turn the
handle anticlockwise (fig. 1).
■For ease of cleaning, the central container
is removable (fig. 2).
■Remove the gauze filter (fig.3) and
wash the whole unit under a jet of
water. If necessary a small brush can
be used.
■With the Self-cleaning Micro filter,
maintenance is reduced and the filter
unit need only be checked every two
weeks. Nevertheless, after each wash it
is advisable to check that the central
container and the gauze filter are not
clogged.
WARNING!
After cleaning the filters, make sure
that they are correctly reassembled
and that the gauze filter is properly
positioned at the bottom of the
dishwasher.
Make sure that the filter is screwed
back, clockwise, into the gauze, as
poor seating of the filter unit could
have an adverse effect on the
efficiency of the appliance.
IMPORTANT
Never use the dishwasher without
the filters.
17
18
PRATICAL HINTS
How to get really good wash
results
■Before placing the dishes in the
dishwasher, remove any remaining
food (bones, shells, pieces of meat or
vegetables, coffee grounds, skin of fruit,
cigarette ash, tooth picks etc. to avoid
blocking the filters, water outlet and
washing arm nozzles.
■Try not to rinse the dishes before
loading them into the dishwasher.
■If saucepans and oven dishes are
encrusted with the remains of burnt or
roast food, it is advisable to leave them
to soak before washing.
■Place the dishes face downwards.
■Try to place the dishes in such a way
that they are not touching one another.
If they are loaded properly you will get
better results.
■After loading the dishes check that the
washing arms can rotate freely.
■Pans and other dishes that have
particularly stubborn food particles or
remnants of burnt food should be left to
soak in water with dishwasher
detergent.
■To wash silver properly:
a) rinse the silver immediately after
use, especially if it has been used for
mayonnaise, eggs, fish etc.;
b) do not sprinkle detergent onto it;
c) keep it separate from other metals.
How to make savings
■If you want the dishwasher to give a
complete wash, place the dishes in the
dishwasher at the end of each meal and
if necessary turn on the COLD RINSE
cycle to soften the food remains and
remove bigger particles of food from the
new load of dishes.
When the dishwasher is full start the
complete wash cycle programme.
■If the dishes are not very dirty or if the
baskets are not very full select an
ECONOMY programme, following the
instructions in the program list.
What not to wash
■It should be remembered that not all
dishes are suitable for washing in a
dishwasher.We advise against using
the dishwasher to wash items in
thermoplastic, cutlery with wooden or
plastic handles, saucepans with
wooden handles, items in aluminium,
crystal, leaded glass unless otherwise
stated.
■Certain decorations may fade. It is
therefore a good idea before loading the
whole batch to wash just one of the
items first so as to be sure that others
like it will not fade.
■It is a good idea not to put silver cutlery
with non-stainless steel handles into
the dishwasher as there could be a
chemical reaction between them.
IMPORTANT
When buying new crockery or
cutlery always make sure that they are
suitable for washing in a dishwasher.
Useful hints
■In order to avoid any dripping from the
top rack, remove the lower rack first.
■If the dishes are to be left in the
machine for some time, leave the door
ajar, to let some air circulate and to
improve the drying performance.
19
WHEN CYCLE IS FINISHED
After every wash it is essential to turn off
water supply and to switch off the machine
by pressing the On/Off button to the off
position.
If the machine is not going to be used for
some time, it is advisable to follow these
rules:
1. do an empty wash with detergent in order
to clean the machine of any deposits;
2. pull out the electric plug;
3. turn off the water tap;
4. fill the rinse aid container;
5. Ieave the door ajar;
6. keep the inside of the machine clean;
7. If the machine is left in places where the
temperature is below 0°C any water left
inside the pipes may freeze. Wait until
the temperature rises above zero and
then wait for about 24 hours before
starting up the dishwasher.
CLEANING AND
MAINTENANCE
■To clean the dishwasher outside, do not
use solvents (degreasing action) neither
abrasives, but only a cloth soaked with
water.
■The dishwasher does not require special
maintenance, because the tank is
self-cleaning.
■Regularly wipe the door gasket with a
damp cloth to remove any food remains
or rinse aid.
■Dishwasher cleaning is recommended,
in order to remove limestone deposits or
dirt. We suggest you run a washing cycle
periodically with specialist dishwasher
cleaning products. For all cleaning
operations the dishwasher must be
empty.
■If, in spite of the routine cleaning of the
filters, you notice that the dishes or pans
are not properly washed or rinsed, check
that all the spray heads on the rotor
arms (fig. A “5”) are clear.
If they are blocked, clean them in the
following way:
1. to remove the upper rotor arm, turn it
until it lines up with the stop marked
by the arrow (fig. 1b). Push it upwards
(fig. 1) and, keeping it pushed in,
unscrew it in a clockwise direction
(to reassemble it repeat the same
operation, but turn it anticlockwise).
The lower rotor arm can be removed
simply by pulling it upwards (fig. 2);
2. wash the rotor arms under a jet of water
to clear any blockage in the spray
heads;
3. when you have finished, refit the rotor
arms in the same position, remembering
to re-align the arrow and screw into
position.
■Both the door lining and the tank lining
are in stainless steel; however, should
spots caused by oxidation occur, this is
probably due to a high level of iron salts
presents in the water.
■The spots can be removed with a mild
abrasive agent; never use chlorine
based materials, steel wool, etc.
1
2
1b
20
DESCRIPTION OF THE CONTROL PANEL
ADIGITAL DISPLAY
B
"PROGRAMME SELECTION" button
C"DELAY START" button
D"ALL in 1" option button
E"ACTION PRO" buttons
F"START"/"RESET" button
(start/cancelling programme)
G "DELAY START" indicator light
H "OPTION SELECTION" light
I "ACTION PRO" lights
L"SALT EMPTY" light
M"RINSE AID EMPTY" light
N Programme guide
O "ON/OFF" button
PWi-Fi light ( )
DIMENSIONS
TECHNICAL DATA
CONSUMPTION (main programmes)*
Programme Energy (kWh) Water (L)
STEAM
UNIVERSAL
ECO
RAPID 24'
Width x Height x Depth (cm)
Depth with door open (cm)
EN 50242 place load
Capacity with pans and dishes
Water supply pressure (MPa)
Fuse / Power input / Supply voltage
16
9 persons
Min. 0,08 - Max. 0,8
See rating plate
Power consumption of the off-mode and of the left-on mode: 0,30 W / 0,45 W
*Values are measured in a laboratory according to European Standard EN 50242 (consumption may
vary according to conditions of usage).
59,8 x 81,8 ÷ 89,8 x 55
117
2,07
1,53
1,08
0,59
21
15
10
9
PBCD E FM NO
LGH I
A
21
PROGRAMME SELECTION
AND SPECIAL FUNCTIONS
(Use in conjunction with programme guide)
"ACTION PRO" button
This button allows you to modify the wash
intensity, according to how dirty your dishes
are, by modifying the wash time and
temperature.
Press the button to increase the intensity of
wash cycle ( indicator light) or to reduce
the intensity of wash, this also allows you to
decrease the wash length time ( indicator
light).
The combination of the button with the 4
main wash programmes enables to have 8
additional wash cycles (achieving a total of
12 programmes of washing).
IMPORTANT
When the dishwasher is switched on,
the setting last used will be indicated.
Programme settings
■Open the door and place the dirty dishes
inside the appliance.
■Press the "ON/OFF" button . The
display will show two lines.
■Choose a programme by pressing the
"PROGRAMME SELECTION" button
("PROGR.").
■If you wish, press the "ACTION PRO +"
or "ACTION PRO –" button.
■If you wish, press the option button (the
corresponding indicator light will turn on).
The option button can be selected or
deselected WITHIN one minute of the
programme commencing.
■Press the "START" button.
The length of the program will be shown on
the display alternating hours with minutes
[I.e.: 1 h (1 hour) / 25 (25 minutes)].
■Close the door (after an audible signal
has sounded, the programme will start
automatically).
WHITIN one minute of the programme
commencing, another programme
can be selected, by pressing the
"PROGRAMME SELECTION" button
(it is also possible to select or deselect
the "ACTION PRO" buttons).
"IMPULSE" programmes
The “IMPULSE” programmes use an
impluse washing technology, which reduces
consumption, noise and increases
performances.
IMPORTANT
The “intermittent” working of the
washing pump MUST NOT BE
considered a malfunction, it is a
characteristic of the impulse washing
so must be considered a normal
function of the programme.
22
Programme interruption
Opening the door when a programme is
running is not recommended especially
during the main wash and final hot rinse
phases. However, if the door is opened
while a programme is running (for example,
to add dishes) the machine stops
automatically and the display will flash the
remaining time before the end of the cycle.
Close the door, without pressing any
buttons. The cycle will start from where it
left off.
WARNING!
If you open the door during the
drying cycle, an audible audio signal
advises you that the drying cycle has
not yet finished.
Changing a running programme
Proceed as follows to change or cancel a
running programme:
■Open the door.
■Hold the "RESET" button down for at
least 5seconds. "00" will appear on the
display and some audible signals will
sound.
■The running programme will be cancelled.
The display will show two lines.
■At this point a new programme can be set.
WARNING!
Before starting a new programme,
you should check that there is still
detergent in the dispenser.
If necessary, top up the dispenser.
If there is any break in the power supply
while the dishwasher is operating, a
special memory stores the selected
programme and, when the power is
restored, it continues where it left off.
Programme end
A 5 second alarm will sound (if not muted)
3 times at 30 second intervals to signal that
the programme has ended.
Dishes can now be removed and the
dishwasher turned off by pressing the
"ON/OFF" button or dishes can be loaded
for a new cycle.
Option buttons
“ALL in 1” button
This option optimises the use of “ALL in 1”
(“3 in 1”/ “4 in 1”/“5 in 1”, etc...) combined
detergents. By pressing this button, the
selected washing programme is modified
to get the best performance from combined
detergents; furthermore, the salt and rinse
aid shortage lights are de-activated.
WARNING!
Once selected, this option keeps
being on (light on) also for next
washing cycles and it can be de-activate
(light off) only by pressing the button
once again.
IMPORTANT
This option is recommended when
using the RAPID 24' program, the
duration of which will be extended for
about 15 minutes, allowing the
detergent tablets to achieve a better
performance.
WIZARD
For details on Wi-Fi settings, please refer
to the appropriate section of this
user manual.
23
"DELAY START" button
Dishwasher start time can be set with this
button, delaying start from 1 to 23 hours.
Proceed as follows to set a delayed start:
■Press the "DELAY START" button ("00"
will appear on the display).
■Press the button again to increase the
delay in hours (each time the button is
pressed the delay is increased by 1 hour
to a maximum of 23). The “DELAY
START” indicator light will turn on.
■To start the countdown press the
"START" button (the “DELAY START”
indicator light will start to flash). At the
end of the countdown, the programme
will automatically start (the “DELAY
START” indicator light will turn off).
If you wish to see which programme has
been selected, press the "PROGRAMME
SELECTION" button.
Proceed as follows to cancel a delayed
start:
■Hold the "RESET" button down for at
least 5seconds. "00" will appear on the
display and some audible signals will
sound.
■The delayed start and the selected
programme will be cancelled.
The display will show two lines.
■At this point, a new programme and
option buttons must be set to start a
new programme as indicated in the
"PROGRAMME SETTINGS" section.
Alarm mute for the PROGRAMME
END
The alarm for the programme end may be
muted as follows:
IMPORTANT
The dishwasher must ALWAYS be off
before start of this procedure.
1. Hold down the "PROGRAMME
SELECTION" button and at the same
time switch on the dishwasher by
pressing the "ON/OFF" button (a brief
audible signal will sound).
2. Keep the "PROGRAMME SELECTION"
button pressed for at least 15 seconds
(during this time, 2audible signals will
sound).
3. Release the button when the second
audible signal sounds ("b1" will appear on
the display to indicate that the alarm is on).
4. Press the same button again ("b0" will
appear on the display to indicate that the
alarm is off).
5. Turn off the dishwasher by pressing the
"ON/OFF" button to confirm the new
setting.
To turn the alarm on again, follow the same
procedure.
24
AUTOMATIC FAULT SIGNALS
Turn off the dishwasher, open the
inlet hose and reset the cycle.
Check if the drain tube is bent or if
the siphon or filters are clogged.
If the problem persists, contact
Customer Service.
Check if the drain tube is bent or if
the siphon or filters are clogged.
If the problem persists, contact
Customer Service.
Contact Customer Service.
Clean the filter plate.
If the problem persists, contact
Customer Service.
FAULTS CAUSE SOLUTION
E2 appears on the display and
the alarm sounds.
E3 appears on the display and
the alarm sounds.
E4 appears on the display and
the alarm sounds.
E5,E6,E7,Ef or EL appears
on the display and the alarm
sounds.
E8 or Ei appear on the display
and the alarm sounds.
No water (inlet hose closed).
The machine cannot drain water.
Water leak
Electronic control fault.
The water heating element is not
working correctly or the filter plate is
clogged.
The dishwasher is able to signal a series of faults in the display.
4. Press the same button again ("A1" will
appear on the display to indicate that the
memorization is on).
5. Turn off the dishwasher by pressing the
"ON/OFF" button to confirm the new
setting.
To disable the memorization, follow the
same procedure.
IMPORTANT
This dishwasher is equipped with an
anti-overflow safety device which will
automatically discharge any excess
water should a problem occur.
WARNING!
To ensure the correct operation of
the anti-overflow safety device, we
recommend that the dishwasher is
not moved or tilted during operation.
If however it is necessary to tilt or
move the dishwasher, please ensure
that the washing cycle is complete
and that there is no remaining water
inside the dishwasher.
Memorization of the last
programme used
The last programme used can be
memorized by following the below:
IMPORTANT
The dishwasher must ALWAYS be off
before start of this procedure.
1. Hold down the "PROGRAMME
SELECTION" button and at the same
time switch on the dishwasher by
pressing the "ON/OFF" button (a brief
audible signal will sound).
2. Keep the "PROGRAMME SELECTION"
button pressed for at least 30 seconds
(during this time, 3audible signals will
sound).
3. Release the button when the THIRD
audible signal sounds ("A0 " will appear
on the display to indicate that the
memorization is off).
25
* The softener unit is set in the factory
at level 4 (d4) as this satisfies the
requirements of the majority of users.
Regulate the setting of your water softener
unit according to the degree of hardness
of your water as follows:
IMPORTANT
The dishwasher must ALWAYS be
off before start of this procedure.
1. Hold down the "PROGRAMME
SELECTION" button and at the same
time switch on the dishwasher by
pressing the "ON/OFF" button (a brief
audible signal will sound).
2. Keep the "PROGRAMME SELECTION"
button pressed for at least 5seconds,
UNTIL a brief audible signal sounds.
The current water softener setting level
will be shown on the display.
3. Press the same button again to select
the required water softener level: each
time the button is pressed, the setting
will increase by one level. When you
have reached "d7", the display will go
back to "d0".
4. Turn off the dishwasher by pressing the
"ON/OFF" button to confirm the new
setting.
WARNING!
If any problem occurs, turn the
dishwasher off by pressing the
"ON/OFF" button and start the
procedure again from the beginning
(STEP 1).
WATER SOFTENER UNIT
Depending on the source of the supply,
water contains varying amounts of limestone
and minerals which are deposited on the
dishes leaving whitish stains and marks.
The higher the level of these minerals
present in the water, the harder the water is.
The dishwasher is fitted with a water
softener unit which, through the use of
special regenerating salt, supplies
softened water for washing the dishes.
The degree of hardness of your water can
be obtained from your water supply
company.
Regulating the water softener
The water softener can treat water with a
hardness level of up to 90°fH (French
grading) or 50°dH (German grading)
through 8 settings.
The settings are listed in the table below:
NO
YES
YES
YES
YES
YES
YES
YES
0
1
2
3
*4
5
6
7
0-5
6-10
11-20
21-30
31-40
41-50
51-60
61-90
0-3
4-6
7-11
12-16
17-22
23-27
28-33
34-50
Level
°fH
(French)
°dH
(German)
d0
d1
d2
d3
d4
d5
d6
d7
Water
hardness
Water
softener
setting
Use of
regenerating
salt
Salt loading indicator
This model is provided with an indicator light
on the control panel which will light up
when it is necessary to reload the salt
container.
IMPORTANT
The appearance of white stains on
dishes is generally an important
sign that the salt container needs
filling.
26
PROGRAMME GUIDE
Wash with prewash
For wash programmes with prewash, it is advisable to add a second dose of detergent (max.
10 g) directly in the machine.
Cycle with alternated action of water jets and steam.
Effective in softening and removing dried up soil and
bacteria, with no need to pre-wash pots and dishes.
Suitable for heavily soiled items that are to be
washed straight after a meal (Max 8 place load).
Quick wash for dishes which are to be washed
immediately after the meal. Wash load of
6 persons.
Suitable for delicate crockery and glassware. Also
for less soiled items excluding pans.
Short cold pre-wash for items that are stored in
the dishwasher until you are ready to wash a full
load.
Once a day - for normal soiled pans and any other
items that have been left all day for washing.
Programme for normally soiled tableware (the
most efficient in terms of its combined energy and
water consumption for that type of tableware).
Programme standardised to EN 50242.
An antibacterial cycle, intended for washing and
sterilising dishes (even heavily stained ones)
babies’ bottles etc.
Intended for rapid washing of very dirty dishes.
Intended for everyday dishwashing. Two final
rinses ensure a high level of hygiene and
cleanliness.
Fast cycle, for “normally” dirty dishes - intended
for frequent washes and normal loads.
= "IMPULSE" programmes
Programme Description
= is the program which allows you to access the functions
Quietest washing cycle. Ideal for functioning by
night and for taking advantage of reduced energy
fares.
27
140
•••
•
75°C
•
•••
••
•••
••
130
85
75°C
65°C
•••
•
•••
•
•••
•
•••
•
•••
•
•••
•
•••
••
•••
•
•
125
120
80
240
190
85
59
24
5
55°C
45°C
45°C
65°C
50°C
70°C
60°C
55°C
Check list
Avarage
duration
in minutes
Special function
buttons available
Detergent for soaking
(Prewash)
Detergent for washing
Clean filter
Check rinse aid
dispenser
Check salt container
Hot pre-wash
Cold pre-wash
Main wash
First cold rinse
Second cold rinse
Hot rinse with rinse aid
With cold water (15°C)
*
-Tolerance ± 10%-
"DELAY START" button
"ALL IN 1" button
Programme contents
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
*
WITH HOT WATER THE TIME REMAINING UNTIL THE END OF THE PROGRAMME IS AUTOMATICALLY DISPLAYED WHILE THE
PROGRAMME IS RUNNING.
YES
YES
YES
YES
YES
YES
YES
YES
YES
•
N/A = OPTION NOT AVAILABLE
YES
YES
28
DISHWASHER
ENROLMENT
Terminology and tools
- Wi-Fi SYSTEM:
You can activate the remote control
system of the dishwasher via Wi-Fi, this
will allow you to control various aspects
of the dishwasher’s operation. For
example, selecting and starting a wash
cycle or pausing a wash cycle that’s in
progress. If the remote control system is
disabled, then the WI-Fi app will still
allow you to track the progress of a wash
cycle and see how much time is left until
it completes. However you cannot
control any of the dishwasher functions
through WI-Fi.
- REGISTRATION PROCEDURE:
This is the process by which the dishwasher
is connected to a wireless router and
enables communication with the WI-Fi
app.
- ON/OFF BUTTON:
If the dishwasher is switched off (via the
“ON/OFF” button or disconnected from
the mains supply, then functionality
through the remote control system will
not be available. To reactivate the Wi-Fi
system, restore power to the
dishwasher, select the P0 program and
then press the "START/RESET" button.
- RESET:
To restore the Wi-Fi system to factory
settings, you need to press two buttons
simultaneously until display the
message AP. On freestanding models,
you should press the "SUPER ECO"
and "ALL IN 1" buttons.
On built-in models, you should press the
"U WASH" " " and " " buttons.
- MODEM SETTING:
To activate the Wi-Fi capabilities of your
dishwasher, you will need to link it to
your internet router or hub. To establish
a wireless connection, you will need to
input the router/hub ID and password.
The dishwasher will only be compatible
with a modem that has the specifications
shown in the table below. If it doesn’t,
then you may not get a Wi-Fi signal.
Wi-Fi uncertified routers may fail to
establish the connection.
Parameter
Frequency
Modulation
Channel
intervals
Channels
Transmission
rate
(over the air)
Receive
sensitivity
Output level
(Class1)
Specifications
2,402 ~ 2,480 MHz
802.11b compatibility:
DSSS (CCK-11, CCK-5.5,
DQPSK-2 and DBPSK-1)
802.11g:
OFDM (default)
5 MHz
1-14
1-11 Mbps for 802.11b
6-54 Mbps for 802.11g
-83 dBm typical
0 to +12 dBm (software
configurable)
•
29
FUNCTIONS
The WI-Fi app allows you to manage the
dishwasher from either indoors or
outdoors.
To comply with relevant standards, the
door of the dishwasher needs to be closed
to control the appliance remotely. If the
door is not closed, then it will not be
possible to start a wash cycle, but it is
possible to use the WI-Fi app.
Within the Wi-Fi app there are
several different functions:
- PROGRAMS/OPTIONS:
Through the menu ”A la carte” you can
select up to 12 programs and up to 4
options (depending on the wash cycle
that is selected) and save them under
"Favourites". The "Quick Start"
function allows you to quickly access a
list of previously selected wash cycles
and quickly set the same one again.
- DELAY START:
This allows you to modify the start time
of the wash cycle (by up to 23 hours).
The Simply-Fi app also allows you to
track the progress of a wash cycle
and see how much time is left until it
completes.
- NOTIFICATION:
The app will inform you about the
progress of a wash cycle (i.e. washing,
rinse, drying phase) and communicate
any problems that arise during the
course of a cycle (e.g. problems with
water supply). At the end of the wash
cycle, the dishwasher will go into
stand-by and the app will return to its
home screen.
- POWER CONTROL:
The app is able to show the levels of
energy consumption at various stages of
the wash cycle, as well as providing daily
and weekly energy reports.
Furthermore, once the cost of the
household electricity supply is determined,
the app will suggest the best time to use
the dishwasher.
- DIAGNOSTICS:
The app informs the user about
any errors or problems that may occur
during the wash cycle (e.g. failure to load
/ unload). The user will be provided with
practical advice on how to solve the
problem (e.g. make sure the filter is
clean, add salt or rinse aid) before
calling the Customer Care Department.
With this the Candy Hoover Group,
declares that this appliance marked
with 0051 complies with the essential
requirements of the R&TTE Directive
1999/5/EC. To receive a copy of the
declaration of conformity, please
contact the manufacturer at:
www.candy-group.com
For detailed information about HOW TO
CONNECT your Wizard appliance and
HOW TO USE it at its best, go
to www.hooverwizard.com or visit the
dedicated Wizard Customer Service website:
www.wizardservice.candy-group.com
30
IDENTIFYING MINOR FAULTS
Should the dishwasher fail to operate, before contacting the Service Centre, make
the following checks:
FAULT CAUSE REMEDY
1 - Machine completely dead
2 - Machine does not
draw water
3 - Machine does not
discharge water
4 - Machine discharges
water continuously
5 - Spray arms are not heard
to rotate
6 - On electronic appliances
without a display: one or
more LED flashing quickly.
Plug is not connected to wall
socket
O/I button has not been pressed
Door is open
No electricity
See causes for no. 1
Water tap is turned off
Programme selector is not at
correct position
The inlet hose is bent
The inlet hose filter is not
correctly connected
Filter is dirty
Outlet hose is kinked
The outlet hose extension is
not correctly connected
The outlet connection on the
wall is pointing downwards not
upwards
Position of outlet hose is too
low
Excessive amount of detergent
Item prevents arms from rotating
Plate and cup filter very dirty
Water inlet tap turned off
Connect electric plug
Press button
Close door
Check the fuse in the plug and
the electricity supply
Check
Turn water tap on
Turn programme selector to
correct position
Eliminate the bends in the hose
Clean the filter at the end of the
hose
Clean filter
Straighten outlet hose
Follow the instructions for
connecting the outlet hose
carefully
Call a qualified technician
Lift outlet hose to at least 40 cm
above floor level
Reduce amount of detergent
Use suitable detergent
Check
Clean plate and cup filter
Switch off the appliance.
Turn on the tap.
Re-set the cycle.
31
N.B.: Should any of the situations occur and should the machine give a bad wash performance,
it is necessary to remove the deposits from the dishes by hand since the final drying cycle hardens the
deposits which a second wash in the machine would not be able to remove.
If the malfunction continues contact a Service Centre quoting the serial number of the dishwasher.
This is found on the plaque on the inside of the dishwasher door at the top or on the guarantee.
This information will make it possible to take more effective action more quickly.
The manufacturers decline any responsibility for any printing mistakes in this instruction booklet.
They also reserve the right to modify their own appliances as necessary without altering the
essential characteristics.
FAULT CAUSE REMEDY
7 - Load of dishes is only
partially washed
8 - Detergent not dispensed
or partially dispensed
9 - Presence of white spots
on dishes
10 -Noise during wash
11 -The dishes are not
completely dry
See causes for no. 5
Bottom of saucepans have not
been washed well
Edge of saucepans have not
been washed well
Spray arms are partially blocked
The dishes have not been
properly loaded
The end of the outlet hose is in
the water
The incorrect amount of
detergent has been measured
out; the detergent is old and hard
The wash programme is not
thorough enough
The lower basket dishes have
not been washed
Cutlery, dishes, pans, etc... stop
the detergent dispenser opening
Water is too hard
The dishes knock against one
another
The revolving arms knock against
the dishes
Inadequate air flow
Rinse aid missing
Check
Burnt on food remains must
be soaked before putting pans
in dishwasher
Reposition saucepans
Remove spray arms by
unscrewing ring nuts clockwise
and wash under running water
Do not place the dishes too
closely together
The end of the outlet hose
must not come into contact
with the outflow water
Increase the measure
according to how dirty the
dishes are and change detergent
Choose a more vigorous
programme
Depress half load button
Position dishes not to obstruct
the dispenser
Check salt and rinse aid level
and regulate amount.
Should the fault persist,
Contact Service Centre
Re-check loading of dishes in
the basket
Again re-check loading
Leave the dishwasher door ajar
at the end of the wash program
to allow the dishes to dry naturally
Fill the rinse aid dispenser
32
Hoover guarantees all parts of this product for 5 years from
the date of purchase. During that time Hoover will replace or
repair all defective parts free of charge, except for parts
subject to fair wear and tear such as belts. The call out fee and
labour costs are chargeable after the first 12 months. To
qualify for benefits under the guarantee, you must be able to
provide proof of date of purchase and the appliance must
have been installed and used in accordance with the
instructions described in this manual. Consequential losses and
accidental damage to the machine is not covered by the
guarantee.
Hoover cannot be responsible for the results of using this
machine for any purposes other than those described in this
manual.
This guarantee does not effect your statutory or common law
rights.
For service and repairs please call our national number:
Always use genuine Hoover spares, available direct from GIAS
Service:
Hoovercare
To maintain your Hoover product in peak condition you may
wish to take out a Hoovercare policy, which for an annual
payment provides a comprehensive maintenance and repair
scheme. For more information please call 08444 995599.
The Hoovercare scheme is not available in Eire.
The manufacturer declines all responsibility in the event of any
printing mistakes in this booklet. The manufacturer also
reserves the right to make appropriate modifications to its
products without changing the essential characteristics.
GIAS Service - Tel: 08444 995599
Support Service [Eire 0818 200021]
Hoover Spares Service
Tel: 01204 556111
This appliance is marked according to the European directive 2012/19/EU on Waste Electrical and Electronic Equipment
(WEEE).
WEEE contains both polluting substances (which can cause negative consequences for the environment) and basic
components (which can be re-used). It is important to have WEEE subjected to specific treatments, in order to remove and
dispose properly all pollutants, and recover and recycle all materials.
Individuals can play an important role in ensuring that WEEE does not become an environmental issue; it is essential to follow
some basic rules:
- WEEE should not be treated as household waste;
- WEEE should be handed over to the relevant collection points managed by the municipality or by registered companies. In
many countries, for large WEEE, home collection could be present.
In many countries, when you buy a new appliance, the old one may be returned to the retailer who has to collect it free of
charge on a one-to-one basis, as long as the equipment is of equivalent type and has the same functions as the supplied
equipment.
The manufacturer declines all responsibility in the event of any printing mistakes in this
booklet. The manufacturer also reserves the right to make appropriate modifications to
its products without changing the essential characteristics.
To consult the product fiche, please refer to the manufacturer website.
15.05 - 41902265
EN
08444 995599
HOOVER SERVICE
FOR YOUR LOCAL ENGINEER PLEASE CALL OUR NATIONAL NUMBER
Areas covered by HOOVER SERVICE DEALERS
Also Channel Islands, Scilly Isles, Orkney, Shetlands
See local telephone directory
Hoover policy is one of continuous development and for this reason
we reserve the right to change specifications without prior notice
HOOVER LIMITED DRAGONPARC ABERCANAID MERTHYR TYDFIL MID-GLAMORGAN CF48 1PQ
EIRE
0818 200021