Table of Contents
Hoover NDEH11RA2TCEXM80 User Manual
Displayed below is the user manual for NDEH11RA2TCEXM80 by Hoover which is a product in the Tumble Dryers category. This manual has pages.
Related Manuals
EN
2
Thank you for choosing this product.
We are proud to offer the ideal product for
you and the best complete range of home
appliances for your daily routine.
Please read and follow these
instructions carefully and operate the
machine accordingly. This booklet provides
important guidelines for safe use,
installation, maintenance and some useful
advice for best results when using your
machine. Keep all documentation in a safe
place for future reference or for any future
owners.
Please check that the following items are
delivered with the appliance:
•
Instruction manual
•
Guarantee card
•
Energy label
Check that no damage has occurred to the
machine during transit. If it as, call for
service by Customer Service Centre.
Failure to comply with the above can
compromise the safety of the appliance.
You may be charged for a service call if a
problem with your machine is caused by
misuse or by incorrect installation.
To contact the Service, ensure that you
have the unique 16
-
character code
available, also called the "serial number".
This code is a unique code for your
product, printed on the sticker that can be
found inside the door opening.
WEEE contains both polluting substances (which
can cause negative consequences for the
environment) and basic components (which can
be re
-
used). It is important to have WEEE
subjected to specific treatments, in order to
remove and dispose properly all pollutants, and
recover and recycle all materials. Individuals can
play an important role in ensuring that WEEE
does not become an environmental issue; it is
essential to follow some basic rules:
WEEE should not be treated as
household
waste;
WEEE should be handed over to the relevant
collection points managed by the municipality or
by registered companies. In many countries, for
large WEEE, home collection could be present.
In many countries, when you buy a new
appliance, the old one may be returned to the
retailer who has to collect it free of charge on a
one
-to-
one basis, as long as the equipment is of
equivalent type and has the same functions as
the supplied equipment.
1.
GENERAL SAFETY RULES
2.
DRAIN HOSE KIT
3.
WATER CONTAINERS
4.
DOOR, FILTERS AND HEAT
EXCHANGER
5.
PRACTICAL HINTS
6.
REMOTE CONTROL (WI-FI)
7.
QUICK USER GUIDE
8.
CONTROLS AND PROGRAMMES
9.
TROUBLESHOOTING AND WARRANTY
This appliance is marked according to
the European directive 2012/19/EU
on Waste Electrical and Electronic
Equipment (WEEE).
Environmental conditions
Contents
3
EN
1. GENERAL SAFETY
RULES
This appliance is intended to
be used in household and
similar applications such as:
- Staff kitchen areas in shops, offices
and other working environments;
- Farm houses;
- By clients in hotels, motels and
other residential type environments;
- Bed and breakfast type environments.
A different use of this appliance
from household environment
or from typical housekeeping
functions, as commercial use by
expert or trained users, is excluded
even in the above applications. If
the appliance is used in a manner
inconsistent with this it may reduce
the life of the appliance and may
void the manufacturer’s warranty.
Any damage to the appliance or
other damage or loss arising
through use that is not consistent
with domestic or household use
(even if located in a domestic or
household environment) shall not
be accepted by the manufacturer to
the fullest extent permitted by law.
This appliance can be used by
children aged from 8 years and
above and persons with reduced
physical, sensory or mental
capabilities or lack of experience
and knowledge if they have been
given supervision or instruction
concerning use of the appliance
in a safe way and understand the
hazards involved.
Children shall not play with the
appliance. Cleaning and user
maintenance shall not be made
by children without supervision.
Children should be supervised
to ensure that they do not play
with the appliance.
Children of less than 3 years
should be kept away unless
continuously supervised.
This machine is solely for
domestic use, i.e. to dry
household textiles and garments.
Ensure that the instructions for
installation and use are fully
understood before operating
the appliance.
Do not touch the appliance
when hands or feet are damp
or wet.
Do not lean on the door when
loading the machine or use the
door to lift or move the machine.
Do not continue to use this
machine if it appears to be faulty.
WARNING
M
isuse of a tumble dryer may
create a fire hazard.
4
The tumble dryer is not to be
used if industrial chemicals
have been used for cleaning.
Lint and fluff must not be allowed
to collect on the floor around the
outside of the machine.
Always remove the plug before
cleaning the appliance.
The drum inside may be very
hot. Always allow the dryer to
complete the cool down period
before removing the laundry.
The final part of a tumble dryer
cycle occurs without heat (cool
down cycle) to ensure that the
items are left at a temperature
that ensures that the items will
not be damaged.
WARNING
During transport ensure
that
the dryer is in an upright
position, if it's necessary
you can only flip in the side
shown.
If the product is in different
side, wait at least 4 hours
before switching on so that
the oil can flow back into the
compressor. Failure to do
this could result in damage
to the compressor.
WARNING
N
ever stop a tumble dryer
before the end of the drying
cycle unless all items are
quickly removed and spread
out so that the heat is
dissipated.
WARNING:
Where the hot surface
symbol
is located the
temperature rise during
operation of the tumble
dryer may be in excess of 60
degrees C.
WARNING
D
o not use the product if the
fluff filter is not in position or
is damaged; fluff could be
ignited.
5
EN
Do not install the product in a
low temperature room or in a
room where there is a risk of
frost occurring. At temperature
around freezing point the
product may not be able to
operate properly: there is a risk
of damage if the water is
allowed to freeze in the
hydraulic circuit (valves, hoses,
pumps). For a better product
performance the ambient room
temperature must be between
5-35°C. Please note that
operating in cold condition
(between +2 and +5°C) might
simply some water condensation
and water drops on floor.
In cases where the dryer is
installed on top of a washing
machine, a suitable stacking kit
must be used according to the
configuration of your appliance:
- Stacking kit "standard size":
for
washing machine with
minimum depth of 44 cm;
- Stacking kit "slim size":
for
washing machine with
minimum depth of 40 cm.
- Universal stacking kit with
sliding: for washing machine
with minimum depth of
47 cm.
The stacking kit shall be
obtainable from service. The
instructions for installation and
any fixing attachments, are
provided with the stacking kit.
NEVER install the dryer up
near curtains.
The appliance must not be
installed behind a lockable door,
a sliding door or a door with a
hinge on the opposite side to
that of the tumble dryer, in
such way that a full opening of
the tumble dryer door is restricted.
For your safety, the appliance
must be correctly installed. If
there is any doubt about installation,
call Service for advice.
Once the machine is in place
the feet should be adjusted to
ensure that the machine is
level.
The technical details (supply
voltage and power input) are
indicated on the product rating
plate.
Electrical connections and
safety instructions
Installation
6
Make sure that the electrical
system is earthed, complies
with all applicable law and that
the (electricity) socket is
compatible with the plug of the
appliance. Otherwise, seek
qualified professional assistance.
Do not use adapters, multiple
connectors and/or extensions.
The plug should be accessible
for disconnection after the
appliance has been installed.
Do not plug the machine in and
switch it on at the mains until
the installation is completed.
If the supply cord is damaged,
it must be replaced
by the
manufacturer, its service
agent
or similarly qualified persons in
order to avoid a hazard.
Adequate ventilation must be
provided in the room where the
tumble dryer is located to
prevent gases from appliances
burning other fuels, including
open fires, being drawn into
the room during operation of
the tumble dryer.
Install the rear of the appliance
close to a wall or vertical surface.
There should be a gap of at
least 12 mm between the
machine and any obstrubtions.
The inlet and outlet air should
be kept clear of obstruction.
Make sure carpets or rugs
do not obstruct the base or any
of the ventilation openings.
Prevent items from falling or
collecting behind the dryer as
these may obstruct the air inlet
and outlet.
Exhaust air must not be
discharged into a flue which is
used for exhausting fumes
from appliances burning gas or
other fuels.
Check regularly that the air
flowing around the dryer is not
restricted, avoiding accumulation
of dust and lint.
Ventilation
WARNING
T
he appliance must not be
supplied through an external
switching device, such as a
timer, or connected to a circuit
that is regularly switched on
and off by a utility.
7
EN
Check frequently the fluff filter
after use, and clean, if necessary.
Always refer to the laundry
care labels for directions on
suitability for drying.
Fabric softeners, or similar
products, should be used as
specified by the fabric softener
instructions.
Do not dry unwashed items in
the tumble dryer.
Clothes should be spin dried or
thoroughly wrung before they
are put into the tumble dryer.
Clothes that are dripping wet
should not be put into the dryer.
Glass fibre curtains should
NEVER be put in this machine.
Skin irritation may occur if
other
garments are contaminated
with
the glass fibres.
Items that have been soiled
with substances such as cooking
oil, acetone, alcohol, petrol,
kerosene, spot removers,
turpentine, waxes and wax
removers should be washed in
hot water with an extra amount
of detergent before being dried
in the tumble dryer.
Remove all objects from pockets
such as lighters and matches.
Lighters and matches must not
be left in pockets and NEVER
use flammable liquids near the
machine.
Maximum load drying weight:
see energy label.
To consult the product technical
specification please refer to the
manufacturer website.
WARNING
Do not tumble dry fabrics
treated with dry cleaning
fluids.
WARNING
Foam rubber materials can
,
under certain circumstances,
when heated become ignited
by spontaneous combustion.
Items such as foam rubber
(latex foam), shower caps,
waterproof textiles, rubber
backed articles and clothes
or pillows fitted with foam
rubber pads MUST NOT be
dried in the tumble dryer.
The Laundry
8
WARNING
Fire hazard / Flammable
materials.
The appliance contains R290,
an eco-sustainable refrigerating
gas that is flammable. Keep
open flames and sources of
ignition away from the appliance.
Check there is no visible
damage on the appliance. Do
not use the appliance if it is
damaged.
Should there be any kind of
problem, please contact your
specialised retailer or one of
our customer support centres.
WARNING
Ensure that the openings on
the appliance and the openings
of the compartment the appliance
is fitted in (for built-in models)
are clear of obstructions.
WARNING
Do not damage the refrigerating
circuit.
Any repairs or interventions on
the appliance must be carried
out only by an authorised
assistance service.
Disposing of the device
incorrectly could cause fires or
poisoning.
Dispose of the device correctly
and do not damage the pipes
used for the circulation of the
refrigerating fluid.
9
EN
2. DRAIN HOSE KIT
In order to avoid to empty the water
container after each drying cycle, the water
can be discharged directly to a waste water
drain pipe. Water Bye-Laws prohibit
connection to a surface water drain. The
waste water drain pipe should be located
adjacent to the tumble dryer.
The kit consists of: 1 hose and 1 bung.
1. The water drainage system is located at
the back of the machine on the lower
right side (figure 2).
2. Disconnect the hose (A) from the fitting
(B) by pulling it upwards (figure 3).
3. Close the extracted tube with the cap
(C) supplied with the kit (figure 4).
4. Connect the hose into the fitting (B)
making sure it is inserted securely
(figures 5-6).
Once the machine is in place, check to
ensure that the new hose does not
kink when
pushing the tumble dryer
into position.
Fitting the drain hose
The hose must be connected to a drain
system with a maximum height of 85
cm compared to the base of the dryer
(figure 1).
WARNING
Switch off and remove the tumble
dryer plug from the electricity supply
before carrying out any work.
10
3. WATER CONTAINERS
The water removed from the laundry during
the drying cycle is collected in a container.
When the container is full, an indicator light,
or on some models a message on the
display, will advise you that it MUST be
emptied (however, we recommend to empty
it after each drying cycle).
1. Gently pull out the water container
holding the handle (A).
When it is full the water container will
weigh about 6 kg.
2. Tilt the water container to empty the
water out through the spout (B).
When empty, replace the water container
back as shown; (C) first insert the base of
the container into position as shown (1)
then gentle push the top into position (2).
3. Press the programme start button to
restart the cycle.
*Depending on model
1. Gently pull the bottom of the kickplate so
that it unclips from the dryer. The top
section can then be unhinged allowing
the kickplate to be completely removed
(A)
.
2. Pull firmly on the handgrip and slide the
water container out of the dryer (B).
Support the container with both hands
(C). When full, the water container will
weigh about 4 kg.
3. Open the lid located on the top of the
container and empty the water (D).
4. Refit the lid and slide the water container
back into position (D). PUSH FIRMLY
INTO PLACE.
5. Refit the kickplate by engaging the
hinges at the top and 'snapping' the lower
clips into place.
*Depending on model
To remove the container bottom
water drawer *
ONLY FOR MODELS WITH DRAIN
HOSE KIT
If you have the option of drainage
near to the dryer yo
u can use the
discharge kit to provide a permanent
drainage for the water collected in the
container of the dryer. This means
that you don't have to empty the water
container.
To remove the container tank in
door drawer *
Very little water will collect during the
first few cycles of a new machine as an
internal reservoir is filled first.
11
EN
4. DOOR, FILTERS AND
HEAT EXCHANGER
Pull on handle to open the door.
To restart the appliance, close the door
and press the programme start button.
Lint filters and heat exchanger cleaning
indicator light
The indicator light illuminates in fixed mode to
signal the need of cleaning the lint filters and in
blinking mode to signal the need of cleaning
the heat exchanger.
If the laundry is not drying check that the
filters are not clogged.
WARNING
Clean the filters before every cycle.
If you clean filters under water, remember
to dry them.
WARNING
Do not use the tumble dryer without
the filters.
In order to have the maximum
effectiveness of the machine,
checking the cleanliness of all filters
before each drying cycle is essential.
Clogged filters and heat exchanger
could increase the drying tim
e and
cause damages and expensive
cleaning operation.
Filters and heat exchanger
WARNING
(For models with water collection tray)
If
you open the door mid cycle, before
the cool-
down cycle has completed,
the handle may be hot. Please use
extreme caution when attempting to
empty the water r
eservoir during the
cycle.
WARNING
When the tumble dryer is in use the
drum and door may be VERY HOT.
Door
12
1. Extract the two filters A and B in
sequence pulling them upwards, as
shown in the figure.
2. Open the filters.
3. Gently remove lints from both filters using
your fingertips or a soft brush, a cloth or
under water running.
4. Close both filters by repositioning them
inside the door, making sure they are
positioned correctly in place.
WARNING
Before reinserting the filters, make
sure there is no lint residue inside the
compartment; if not, remove it with a
vacuum cleaner.
To clean the lint filters
13
EN
1. Remove the kickplate.
2. Turn the handle anti-clockwise and pull
out the front cover.
3. Gently clean the heat exchanger using a
soft brush or a vacuum cleaner, to
remove any dust or fluff, paying attention
to not damage the fins.
4. Refit the front cover ensuring it is in the
right position. Turn the handle clockwise
to lock the front cover.
5. Refit the kickplate.
WARNING
Do not touch the fins with hands in
order to avoid injury.
Be careful when cleaning in order not
to damage the heat exchanger.
WARNING
Clean the exchanger every six months
or when
the filters cleaning indicator
light blinks.
To clean the heat exchanger
14
5. PRACTICAL HINTS
Before using the tumble dryer for the first
time:
Please read this instruction book
thoroughly.
Remove all items packed inside drum.
Wipe the inside of the drum and door with
a damp cloth to remove any dust which
may have settled in transit.
Make sure that the laundry you are going to
dry is suitable for drying in a tumble dryer,
as shown by the care symbols on each
item. Check that all fastenings are closed
and that pockets are empty. Turn the
articles inside out. Place clothes loosely in
the drum to make sure that they don't get
tangled.
Silk, nylon stockings, delicate embroidery,
fabrics with metallic decorations, garments
with PVC or leather trimmings.
Only put into the tumble dryer laundry which
has been thoroughly wrung or spin-dried.
The drier the laundry the shorter the drying
time thus saving electricity.
ALWAYS
Check that the filters are clean before
every drying cycle.
NEVER
Put dripping wet items into the tumble
dryer, this may damage the appliance.
By care symbols
These can be found on the collar or inside
seam:
Suitable for tumble drying.
Tumble drying at high temperature.
Tumble drying at low temperature
only.
Do not tumble dry.
If the item does not have a care label it
must be assumed that it is not suitable for
tumble drying.
By amount and thickness
Whenever the load is bigger than the dryer
capacity, separate clothes according to
thickness (e.g. towels from thin underwear).
By type of fabric
Cottons/linen: Towels, cotton jersey, bed
and table linen.
Synthetics: Blouses, shirts, overalls, etc.
made of polyester or polyamid, as well as
for cotton/synthetic mixes.
WARNING
Do not overload the drum, large items
when wet exceed the maximum
admissible clothes load (for example:
sleeping bags, duvets).
Sort the load as follows
Energy saving
During the last 15 minutes the load is
always tumbled in cool air.
WARNING
Do not dry articles which have been
treated with a dry cleaning fluid or
rubber clothes (danger of fire or
explosion).
Do not tumble dry
Clothes preparation
15
EN
Clean the filters after every drying cycle.
In models equipped with a water
collection tray, the tray should be emptied
after every drying cycle.
After each period of use, wipe the inside
of the drum and leave the door open for a
while to allow circulation of air to dry it.
Wipe the outside of the machine and the
door with a soft cloth.
DO NOT use abrasive pads or cleaning
agents.
To prevent the door sticking or the
buildup of fluff clean the inner door and
gasket with a damp cloth after every
drying cycle.
WARNING
For electrical data refer to the rating
label on the front of the dryer cabinet
(with the door open).
WARNING
Always switch off and remove the plug
from the electricity supply before
cleaning this appliance.
WARNING
The drum, door and load may be very
hot.
Cleaning the dryer
16
6. REMOTE CONTROL (WI-FI)
This appliance is equipped with Wi-Fi
technology that allows you to control it
remotely via App.
APPLIANCE PAIRING (ON APP)
Download the hOn App on
your device by
framing the following QR code:
or by the link:
go.haier-europe.com/download-app
Open the App, create the user profile
(or log-
in if it is already created previously)
and pairing the appliance following the
instructions on the device display.
TO ENABLE REMOTE CONTROL
Check that the router is switched on and
connected to the Internet.
Load the laundry and close the door.
Turn the programme selector to the
REMOTE CONTROL (Wi-Fi) position
:
the controls on the control panel will be
disabled.
Start the cycle using the app. When the
cycle has been completed, turn off the
machine by turning the programme
selector to the OFF position.
TO DISABLE REMOTE CONTROL
To exit REMOTE CONTROL
mode while
a cycle is underway, turn the programme
selector to any position other than
REMOTE CONTROL (Wi-
Fi), without
going through the OFF
. The control
panel on the appliance will be operative
once again.
With the door closed, turn the programme
selector to the REMOTE CONTROL (Wi
-
Fi)
position to control the appliance using
the app once again. If there is a cycle
underway, it will continue.
With the door opened, the REMOTE
CONTROL will be disabled. To
enable
it again, close the door, turn the
programme selector to any position
other than REMOTE CONTROL and
then select it again.
The frequency of the home Wi-Fi
network has to be set on the 2.4 GHz
band. You can not configure the
machine if your home network is set
to the 5 GHz band.
Get all the details of the Wi-Fi
functions by browsing the App in
DEMO mode.
The App is available for devices
running b
oth Android and iOS, both
for tablets and for smartphones.
17
EN
7. QUICK USER GUIDE
1. Open the door and load the drum with
laundry. Ensure that garments do not
hinder closure of the door.
2. Gently close the door pushing it slowly
until you hear the door 'click' shut.
3. Select the desired drying programme by
turning the programme knob or, in some
models, by pressing the specific button
(check the programme table for specific
details).
4. Press the programme start button. The
dryer will start automatically.
5. If the door is opened during the
programme to check the laundry, it is
necessary to press programme start
to recommence drying after the door
has been closed.
6. When the cycle is nearing completion
the machine will enter the cool down
phase, the clothes will be tumbled in
cool air allowing the load to cool down.
7. Following the completion of the cycle
the drum will rotate intermittently to
minimize creasing. This will continue
until the machine is switched OFF or the
door is opened.
Power input / Power current fuse amp/
Supply voltage: see rating plate.
Maximum load: see energy label.
Energy class: see energy label.
8. CONTROLS AND
PROGRAMMES
A
PROGRAMME SELECTOR with
OFF position
B
START/PAUSE button
C
DELAY START button
D
TIME CYCLE SELECTION/RAPIDS
button
E
ACTIVE DRY button
F
DRYING SELECTION button
G
ANTI CREASE button
H
DISPLAY
F+G
CHILD LOCK
Technical data
Do not open the door during the
automatic programmes in order to
obtain a proper drying.
18
Rotating the programme selector in both
directions it's possible to select the
desired drying programme.
To cancel the selections or switch off the
appliance rotate the programme selector
on OFF (remember to unplug the appliance).
- Language setting
After connecting the machine to the
network and turning it on, press the
button "D" or "E" to see on the display
the available languages. ENGLISH is
always the first language shown.
Select the desired language pressing the
START/PAUSE button.
- Change the language
If you want to change the setting language
you will have to press simultaneously "D"
and "E" buttons for about 5 seconds.
ENGLISH will appear on the display, and
you will be able to choose a new language.
To start the selected cycle with the preset
parameters, press START/PAUSE. When
the programme is running, the display will
show the time to elapse.
Moreover, if you want to modify the
chosen programme, press the desired
options buttons, modify the default
parameters and then press START/
PAUSE button to start the cycle.
After switching on the appliance, wait a few
seconds for the programme to start running.
PROGRAMME DURATION
When a programme is selected the
display automatically shows the cycle
duration, which can vary, depending on
the options selected.
Once the programme has started you will
be kept informed constantly of the time
remaining to the end of the drying cycle.
The appliance calculates the time to the
end of the selected programme based
upon a standard loading, during the cycle,
the appliance corrects the time to the
humidity level of the load.
PROGRAMME END
"END" ("End" on some models) will
appear in the display at the end of the
programme, it is now possible to open the
door.
At the end of the cycle, turn off the
appliance by turning the programme
selector to the OFF position.
The programme selector must
ALWAYS be put in the OFF position at
the end of the drying cycle before a
new one can be selected.
Only the options compatible with the
set programme can be selected.
Close the porthole BEFORE pressing
the START/PAUSE button.
START/PAUSE button
First starting
PROGRAMME SELECTOR with
OFF position
WARNING
Don’t touch the buttons while inserting
the plug because the machines
calibrates the systems during the first
seconds: touching the buttons
, the
machine couldn’t work property. In
this case, remove the plug and repeat
the operation.
19
EN
PAUSING THE MACHINE
Keep the START/PAUSE button pressed
for about 2 seconds (the name of the
programme and the residual time display
will flash, showing that the machine is
paused).
Press the START/PAUSE button again to
re-start the programme from the point it
had been paused at.
CANCELLING THE SET PROGRAMME
To cancel the programme, turn the
programme selector to the OFF position.
If there is a break in the power supply
whilst the machine is operating, when
the power is restored, by pressing the
START/PAUSE button, the machine will
restart from the beginning of the phase it
was in when the power was lost.
This button allows to delay the start of the
programme from 30 minutes (1 hour on
some models) to 24 hours in 30 minutes
intervals (1 hour on some models).The
delay selected is shown on the display.
After pressing the START/PAUSE button
the time showed decrease minute after
minute.
It's possible transform a cycle from
automatic to programmed, up to 3
minutes after the start of the cycle.
The progressive pressure increases the
time in 10 minute intervals. After this
selection to reset the automatic drying
functioning is necessary to switch off the
dryer.
In case of incompatibility, all indicator
lights flash quickly for 3 times.
If the programme selector is positioned
on the rapid programmes CARE
(30'/45'/59') the progressive pressure of
the button allows you to choose one of
three durations indicated.
ACTIVE DRY is the perfect cycle to use if
you want to remove bad smells from the
linens smoothing creases. This cycle can
quickly refresh the garments that you
need, ensuring the best compromise
between time and drying performance.
If you want to select this option, press the
ACTIVE DRY button once. It is available
only during program selection.
This option overwrites the program
selected with a dedicated one.
If you want to deselect the ACTIVE DRY
option, press the ACTIVE DRY button.
When you deselect the option, the
machine will show again the original
program name.
This button allows to set the desired
dryness level editable option up to 3
minutes after the starting of the cycle:
Ready to Iron: it leaves the garments
slightly wet to facilitate ironing.
Dry Hanger: to get garment ready to
be hang.
Dry wardrobe: for laundry that can be
directly stored.
Extra-dry: to get completely dry
garments, ideal for full load.
DRYING SELECTION button
ACTIVE DRY button
TIME CYCLE SELECTION/RAPIDS
button
Opening of the porthole with delayed
start set, after re-
closing the porthole,
press start again to resume the counting.
DELAY START button
20
This appliances is equipped with Drying
Manager function. On automatic cycles,
each level of intermediate drying, prior to
the reaching the selected one, is
indicated by flashing the light indicator
corresponding to the degree of drying
reached.
In case of incompatibility, all indicator
lights flash quickly for 3 times.
During the cycle the option sets alternate
movements of the drum to reduce the
folds and automatically sets the drying
level to "Ready to Iron". Moreover this
option activate an anti-creases movement
of the drum pre cycle in case of activation
of the delay and at the end of drying
cycle. It is activated every 10 minutes, up
to 6 hours after the end of the drying
cycle.
To stop the movements set the
programme selector to OFF. Useful when
it's not possible to remove immediately
the laundry.
Pressing simultaneously the buttons "F"
and "G" for about 2 seconds, the
machine allows you to lock the keys. In
this way, you can avoid making accidental
or
unwanted changes if a button on the
display is pressed accidently during a cycle.
The key lock can be simply cancelled by
pressing the two buttons simultaneously
again.
In case of opening of porthole with
activated CHILD LOCK, the cycle stops
but the lock is kept: to restart the cycle,
you must remove the lock and press
START/PAUSE again.
CHILD LOCK can be modified at any
time of the cycle.
The display shows the remaining time for
drying, the postponed time in case of
delayed start selection and other
notifications setting.
1) DRYING SELECTION INDICATOR
LIGHTS
The indicator lights display the degrees of
dryness that can be selected by the
relevant button.
2) ANTI CREASE INDICATOR LIGHT
The indicator light shows the selection of
the relevant option.
3)
LINT FILTERS AND HEAT EXCHANGER
CLEANING INDICATOR LIGHT
The indicator light illuminates in fixed mode
to signal the need of cleaning the lint filters
and in blinking mode to signal the need of
cleaning the heat exchanger.
4) Wi-Fi INDICATOR LIGHT
On models equipped with Wi-Fi, it
indicates the status of the connection. It
could be:
- FIXED ON: remote control enabled.
- SLOW FLASHING: remote control
disabled.
- QUICK FLASHING FOR 3 SECONDS,
THEN OFF: the machine cannot connect
to the home Wi-Fi network or has not yet
been associated with the App.
Display
CHILD LOCK
ANTI CREASE button
21
EN
- SLOW BLINKING FOR 3 TIMES, THEN
OFF FOR 2 SECONDS: reset of the Wi-Fi
network (during the association with the App).
- ON FOR 1 SECOND, THEN OFF FOR 3
SECONDS: the door is open. Remote
control cannot be activated.
For all the information about the
functionality and the instructions for an
easy configuration of the Wi-Fi, please
refer to:
go.he.services/htd-5d
The standard cycle COTTON DRY ( )
is the most energy efficient and best suited
for drying normal wet cotton laundry.
The table in last page shows the
approximate time and energy consumption
of the main drying programmes.
Maximum Drying Weight
Cottons
Max. capacity
declared
Synthetics or
Delicates
Max. 4 kg
Power consumption of off-mode: 0,40 W
Power consumption of left-on mode:
0,75 W
EN 61121 - Programme To Use
- STANDARD DRY COTTON
- IRON DRY COTTON
(WHITES - Ready to Iron)
- EASY-CARE TEXTILE
(SYNTHETICS - Dry Hanger)
WARNING
Only for 10/11 kg capacity Tumble
Dryer supplied with drain hose kit:
connect the drain hose for recovering
the condenser water (according to
instruction in the dedicated chapter).
WARNING
The real duration of drying cycle
depends by the starting humidity level
of the laundry due to spin speed, type
and amount of load, cleanliness of
filters and ambient temperature.
WARNING
Clean the filters before every cycle.
Information for Test Laboratory
Drying Guide
22
PROGRAMMES
Selectable Options
CAPACITY
(kg)
DRYING
TIME (min)
WHITES Full *
ECO COTTON - - - - Full *
WOOLMARK
-
-
-
-
1 70’
WATERPROOF
REVITALIZE
-
-
-
2 *
SYNTHETICS 4 *
SHIRTS
-
2,5 *
JEANS
-
-
-
-
4 *
FITNESS - - 4 *
SOFT CARE
-
- - 2 *
FRESH CARE
-
-
-
3,5 *
ALLERGY CARE - - 4 Max 220’
CARE 30-45-59 - - 2,5 *
ALL IN ONE
-
-
-
6 *
AUTO CARE
-
4 *
REMOTE CONTROL (Wi-Fi)
Position that you have to select when you want to enable remote control through the
App (via Wi-Fi).
* The real duration of drying cycle depends by the starting humidity level of the laundry due to spin
speed, type and amount of load, cleanliness of filters and ambient temperature.
Table of programmes
23
EN
To dry different types of fabrics and colors,
the tumble dryer has specific programs to
meet every need of drying (see table of
programmes).
REMOTE CONTROL (Wi
-Fi)
Position that you have to select when you
want to
enable/disable remote control
through the App, via Wi
-Fi.
In this case, the start of cycle will take place
through the App commands.
More details in the REMOTE CONTROL
(Wi
-Fi) section.
WHITES
The right cycle to dry cottons, sponges and
towels.
ECO COTTON
The cotton program (hang dry) is the most
efficient program in energy consumption.
Suitable for cottons and linens.
WOOLMARK
Woolen clothes: the program can be used
to dry up to 1 kg of laundry (around 3
jumpers). It is recommended to reverse all
clothes
before drying.
Timing can change due to dimensions and
thickness of load and to spinning chosen
during washing.
At the end of the cycle, clothes are ready to
be worn, but if they are heavier, edges can
be a big wet: it is suggested to dry them
naturally.
It is recommended to unload clothes at the
very end of the cycle.
Attention: felting process of wool is
irreversible; please dry exclusively with
symbol "ok tumble" on the garment
label. This programme is not indicated
for acrylic clothes.
WATERPROOF REVITALIZE
A special service to revitalize the
waterproofing treatment of the linens.
SYNTHETICS
To dry synthetic fabrics that need an
accurate and specific treatment.
SHIRTS
This specifics cycle has been conceived to
dry shirts minimizing tangles and folds
thanks specific movements of the drum. It's
recommended to take out the linens
immediately after drying cycle.
JEANS
Dedicated to dry uniformly fabrics like jeans
or denim. It's recommended flip over the
garments before drying.
FITNESS
The Fitness program takes care of your
technical garments used for sport and
fitness: the machine dries gently with
special care to avoid shrinking and
deterioration of elastic fibers.
The wool drying cycle of this
machine has been approved by the
Woolmark Company for the drying of
machine washable wool products
provided that the products are
washed and dried according to the
instructions on the garment label and
those issues by the manufacturer of
this machine M1530.
In UK, Eire, Hong Kong and India the
Woolmark trade mark is a
Certification trade mark.
Description of programmes
24
SOFT CARE
With the Soft Care program and a small
load, the machine will take care of your
most delicate garments.
FRESH CARE
Thanks to Fresh Care cycle, the machine
can take care of your different fabrics
together (cotton and synthetic), drying them
out even in 59'.
If the load is less than the recommended
one or with a low level of residual humidity,
the cycle is shortened for not over
-
drying
the garments.
ALLERGY CARE
One specific cycle that dries and in the
same time helps to reduce the main
allergens as dust mites, pet hair, pollens
and residual of powder detergents.
CARE (30'/45'/59')
This drying cycle allows you to have items
ready in a short time, you can choose to dry
them in 30, 45, 59 minutes.
ALL IN ONE
A new innovative cycle to dry different kinds
of fabrics in the same time. The dryer
provides an alert when the lightweight
fabrics are dry and ready to are taking out
(on the display the text AIO blinks for 3
minutes and an acoustic sound is emitted).
After this step it's necessary to press start
again to complete the drying for the
leftovers heavier linens.
AUTO CARE
The new Auto Care cycle is the new
exclusive program that is capable to adapt
its drying technology to the capacity and
typology of clothes automatically.
25
EN
9. TROUBLESHOOTING
AND WARRANTY
Defects you can remedy yourself
Before calling Service for technical advice
please run through the following checklist. A
charge will be made if the machine is found
to be working or has been installed
incorrectly or used incorrectly. If the
problem persists after completing the
recommended checks, please call Service,
they may be able to assist you over the
telephone.
Time display to end could change during
drying cycle. The time to end is
continuously checked during the drying
cycle and the time is adjusted to give the
best estimation time. The displayed time
may increase or decrease during the
cycle and this is normal.
Drying time is too long/clothes are not
dry enough…
Have you selected the correct drying
time/programme?
Were the clothes too wet? Were the
clothes thoroughly wrung or spindried?
Do the filters need cleaning?
Does the heat exchanger need cleaning?
Is the dryer overloaded?
The dryer does not operate…
Is there a working electricity supply to the
dryer? Check using another appliance
such as a table lamp.
Is the plug properly connected to the
mains supply?
Is there a power failure?
Has the fuse blown?
Is the door fully closed?
Is the dryer switched on, both at the
mains supply and at the machine?
Has the drying time or the programme
been selected?
Has the machine been switched on again
after opening the door?
The dryer is noisy…
Switch off the dryer and contact Service
for advice.
The filters cleaning indicator light is on…
Do the filters or the heat exchanger need
cleaning?
The water container indicator light is on
*
…
Does the water container need emptying?
* In some models, this will be indicated
with a message appearing on the display.
Should there still be a problem with your
dryer after completing all the recommended
checks, please call Service for advice. They
may be able to assist you over the
telephone or arrange for a suitable
appointment for an engineer to call under
the terms of your guarantee. However, a
charge may be made if any of the following
applies to your machine:
Is found to be in working order.
Has not been installed in accordance with
the installation instructions.
Has been used incorrectly.
Always use genuine spares, available direct
from Service.
Spares
Customer Service
What might be the cause of...
26
To ensure the continued safe and efficient
operation of this appliance we recommend
that any servicing or repairs are only carried
out by an Authorised Service engineer.
By placing the mark on this
product, we are confirming compliance
to all relevant European safety, health
and environmental requirements which
are applicable in legislation for this
product.
To ensure safety when disposing of an old
tumble dryer disconnect the mains plug
from the socket, cut the mains power cable
and destroy this together with the plug. To
prevent children shutting themselves in the
machine break the door hinges or the door
lock.
The manufacturer declines all
responsibility for any printing errors in
the booklet included with this product.
Moreover, it also reserves the right to
make any changes deemed useful to its
products without changing their
essential characteristics.
RADIO EQUIPMENT
INFORMATION
Technology Wi-Fi BLE
Standard IEEE
802.11b/g/n
Bluetooth
v4.2,
BR/EDR,
BLE
Frequency
Band(s) [MHz] 2401÷2483 2402÷2480
Maximum
Power [mW]
100 10
Hereby, Candy Hoover Group Srl
declares that the radio equipment is
in
compliance with Directive 2014/53/EU.
The full text of the EU declaration of
conformity is available at the following
internet address: www.candy-group.com
Warranty
The product is guaranteed under the
terms and conditions stated on the
certificate included with the product. The
certificate has to be stored so as to be
sho
wn to the Authorized Customer
Service Centre in case of need. You can
also check the warranty conditions on
our web site. To obtain assistance,
please fill in the form on-
line or contact
us at the number indicated on the
support page of our web site.
Service
hldsk
Energy Capacity Time
A++
Energy
Energy
Time Min.
Energy
Energy
Time Min.
Energy
A++ A++ A++
Capacity (kg)
Class
Whites
Whites
Cotton
Cotton ½
Whites
78910
2,15 2,41 2,70
253 281 325
1,89 2,12 2,38
222 248 286
1,72 2,16
260
1,08 1,16
118 149
1,38 1,54 1,73
162 180 208
3,04
224
350
2,67
308
2,43
280
1,21
153
1,94
135
225
1,93
11
3,39
280
438
2,98
385
2,71
350
1,24
169
2,17
A++
Time
Time Min.
Time Min.
kWh
kWh
kWh
Min. 202
0,97 kWh
kWh
-NDE H T -
21.06 - 40018063 - IDM s.r.l.