Indesit BWA 71053X W IT User Manual
Displayed below is the user manual for BWA 71053X W IT by Indesit which is a product in the Washing Machines category. This manual has pages.
Related Manuals
www.indesit.com/register
User Manual
2
HEALTH & SAFETY GUIDE ................................................................. 3
Safety Instructions ........................................................................................3
USER MANUAL ........................................................................... 5
Product description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Detergent dispenser drawer ................................................................................5
Technical data for water connection ........................................................................5
Control panel ..............................................................................................6
Wash cycles ................................................................................................ 6
Options ....................................................................................................7
Push & Wash ...............................................................................................8
Functions ..................................................................................................9
Wash cycle table ..........................................................................................10
Accessories ...............................................................................................10
How to use the appliance ................................................................................11
First time use .............................................................................................11
Daily use ..................................................................................................11
Hints and tips .............................................................................................12
Cleaning & maintenance .................................................................................13
Disconnect the water and power supplies .................................................................13
Clean the washing machine ...............................................................................13
Cleaning the detergent dispenser drawer ..................................................................13
Care for the door and drum ...............................................................................13
Clean the pump ...........................................................................................13
Check the water inlet hose ................................................................................13
Troubleshooting .........................................................................................14
Manual door opening .....................................................................................15
Transport and handling ...................................................................................15
Service ...................................................................................................16
INSTALLATION GUIDE ...................................................................17
USER MANUAL
THANK YOU FOR BUYING A INDESIT PRODUCT.
In order to receive a more complete assistance,
please register your appliance on www.indesit.com/register
INDEX
EN
Health & Safety guide
3
SAFETY INSTRUCTIONS IMPORTANT TO BE READ AND OBSERVED
Before using the appliance, read these safety
instructions. Keep them nearby for future reference.
These instructions and the appliance itself provide
important safety warnings, to be observed at all
times. The manufacturer declines any liability for
failure to observe these safety instructions, for
inappropriate use of the appliance or incorrect
setting of controls.
Very young children (0-3 years) should be kept
away from the appliance. Young children (3-8years)
should be kept away from the appliance unless
continuously supervised. Children from 8years old
and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge can use this appliance only if they
are supervised or have been given instructions on
safe use and understand the hazards involved.
Children must not play with the appliance. Cleaning
and user maintenance must not be carried out by
children without supervision.
Never open the door forcibly or use it as a step.
PERMITTED USE
CAUTION: The appliance is not intended to be
operated by means of an external switching device,
such as a timer, or separate remote controlled system.
This appliance is intended to be used in household
and similar applications such as: sta kitchen areas in
shops, oces and other working environments; farm
houses; by clients in hotels, motels, bed & breakfast
and other residential environments.
Do not load the machine above the maximum
capacity (kg of dry cloth) indicated in the programme
table.
This appliance is not for professional use. Do not
use the appliance outdoors.
Do not use any solvents (e.g. turpentine, benzene),
detergents containing solvents, scouring powder,
glass or general purpose cleaners, or ammable
uids; do not machine wash fabrics that have been
treated with solvents or ammable liquids.
INSTALLATION
The appliance must be handled and installed by
two or more persons- risk of injury. Use protective
gloves to unpack and install- risk of cuts.
If you want to stack a dryer on top of your washing
machine, rst contact our After-Sales Service or your
specialist dealer to verify whether this is possible.
This is only possible if the dryer is attached to the
washing machine by means of appropriate stacking
kit available through our After- Sales Service or your
specialist dealer.
Move the appliance without lifting it by the
worktop or top lid.
Installation, including water supply (if any) and
electrical connections and repairs must be carried
out by a qualied technician. Do not repair or replace
any part of the appliance unless specically stated in
the user manual. Keep children away from the
installation site. After unpacking the appliance,
make sure that it has not been damaged during
transport. In the event of problems, contact the
dealer or your nearest After-sales Service. Once
installed, packaging waste (plastic, styrofoam parts
etc.) must be stored out of reach of children- risk of
suocation. The appliance must be disconnected
from the power supply before any installation
operation- risk of electric shock. During installation,
make sure the appliance does not damage the
power cable - risk of re or electric shock. Only
activate the appliance when the installation has
been completed.
Do not install your appliance where it may be
exposed to extreme conditions, such as: poor
ventilation, temperatures below 5°C or above 35°C.
When installing the appliance make sure that the
four feet are stable and resting on the oor, adjusting
them as required, and check that the appliance is
perfectly to level using a spirit level.
If the appliance is being installed on wood or
“oating” oors (certain parquet and laminate
materials), secure a 60x60x3cm (at least) sheet of
plywood to the oor then place the appliance on
top of this.
Connect the water inlet hose(s) to the water
supply in accordance with the regulations of your
local water company.
For cold ll only models: do not connect to the
hot water supply.
For models with hot ll: the hot water inlet
temperature must not exceed 60°C.
The washing machine is tted with transport
bolts to prevent any possible damage to the interior
during transport. Before using the machine, it is
imperative that the transport bolts are removed.
After their removal, cover the openings with the 4
enclosed plastic caps.
After installation of the device, wait a few hours
before starting it so that it acclimates to the
environmental conditions of the room.
Make sure that the ventilation openings in the
base of your washing machine (if available on your
model) are not obstructed by a carpet or other
material.
Health & Safety guide
4
Use only new hoses to connect the appliance to
the water supply. The old hose-sets should not be
reused.
The supply water pressure must be in the
01-1Mpa range.
ELECTRICAL WARNINGS
It must be possible to disconnect the appliance
from the power supply by unplugging it if plug is
accessible, or by a multi-pole switch installed
upstream of the socket in accordance with the
wiring rules and the appliance must be earthed in
conformity with national electrical safety standards.
Do not use extension leads, multiple sockets or
adapters. The electrical components must not be
accessible to the user after installation. Do not use
the appliance when you are wet or barefoot. Do not
operate this appliance if it has a damaged power
cable or plug, if it is not working properly, or if it has
been damaged or dropped.
If the supply cord is damaged, it must be replaced
with an identical one by the manufacturer, its service
agent or similarly qualied persons in order to avoid
a hazard- risk of electric shock.
CLEANING AND MAINTENANCE
WARNING: Ensure that the appliance is switched
o and disconnected from the power supply before
performing any maintenance operation; never use
steam cleaning equipment- risk of electric shock.
DISPOSAL OF PACKAGING MATERIALS
The packaging material is 100% recyclable and is marked with the recycle
symbol .
The various parts of the packaging must therefore be disposed of
responsibly and in full compliance with local authority regulations
governing waste disposal.
DISPOSAL OF HOUSEHOLD APPLIANCES
This appliance is manufactured with recyclable or reusable materials.
Dispose of it in accordance with local waste disposal regulations.
For further information on the treatment, recovery and recycling of
household electrical appliances, contact your local authority, the
collection service for household waste or the store where you purchased
the appliance. This appliance is marked in compliance with European
Directive 2012/19/EU, Waste Electrical and Electronic Equipment (WEEE).
By ensuring this product is disposed of correctly, you will help prevent
negative consequences for the environment and human health.
The symbol on the product or on the accompanying documentation
indicates that it should not be treated as domestic waste but must be
taken to an appropriate collection center for the recycling of electrical
and electronic equipment.
EN
User manual
5
PRODUCT DESCRIPTION
1. Worktop
2. Detergent dispenser
3. Control panel
4. Door handle
5. Door
6. Water lter - behind plinth
7. Plinth (removable)
8. Adjustable feet (4)
1.
3.
2.
5.
4.
7.
6.
8.
DETERGENT DISPENSER DRAWER
Successful washing results also depend on the correct dose
of detergent: adding too much detergent will not necessarily
result in a more ecient wash, and may in fact cause
build up on the inside of your appliance and contribute to
environmental pollution.
! Do not use hand washing detergents because these create
too much foam.
! Use powder detergent for white cotton garments, for
prewashing, and for washing at temperatures over 60°C.
! Follow the instructions given on the detergent packaging.
Open the detergent dispenser drawer and pour in the
detergent or washing additive, as follows.
1. Compartment : Washing detergent (powder or liquid)
• If liquid detergent is used, the removable plastic
partition A (supplied) should be used for proper
dosage.
• If powder detergent is used, insert the partition into
slot B.
2. Compartment
• Do not insert detergent in this compartment.
3. Compartment : Additives (fabric softener, etc.)
• The fabric softener must never exceed the “max” level
indicated on the central pin.
TECHNICAL DATA FOR WATER CONNECTION
Water connection
Water supply Cold
Water tap 3/4” threaded hose connector
Minimum water supply pressure 100 kPa (1 bar)
Maximum water supply pressure 1000 kPa (10 bar)
User manual
6
WASH CYCLES
Follow the instructions on the symbols of the garment’s wash care label. The value indicated in the symbol is the maximum
recommended temperature for washing the garment.
CONTROL PANEL
1 ON/OFF button
2 START/PAUSE button and indicator
light
3 WASH CYCLE PHASE indicator lights
4 DOOR LOCKED indicator light
5 OPTION buttons and indicator lights
6 CHILDLOCK button and indicator
light
7 DELAY START button
8 SPIN button
9 TEMPERATURE button
10 WASH CYCLE SELECTOR KNOB
11 PUSH & WASH button
DAILY COTTON
A 30°C cycle for cotton garments. It allows for reducing
electricity consumption for heating the water while
guaranteeing good washing performance. Suitable for
lightly soiled garments.
DAILY SYNTHETICS
A 30°C cycle for synthetic garments. It allows for reducing
electricity consumption for heating the water while
guaranteeing good washing results. Suitable for lightly
soiled garments.
COLOUREDS
A 30°C cycle that helps to preserve colours, suitable
for cotton or synthetic coloured garments. It allows for
reducing electricity consumption for heating the water
while guaranteeing good washing results. Suitable for
lightly soiled garments.
DELICATES
Suitable for washing very delicate garments. It is advisable
to turn the garments inside out before washing them. For
best results, use liquid detergent on delicate garments. For
washing silk items and curtains, select cycle 4 and activate
the option; the machine will end the cycle with the
laundry soaked and the indicator light will ash. To drain the
water so that the laundry can be removed, press the START/
PAUSE button or the button.
RAPID 30MIN
For washing lightly soiled garments in a short time. Not
suitable for wool, silk and garments to be washed by hand.
COTTON
Suitable for washing towels, underwear, table cloths, etc.
made of resistant linen and cotton that are moderately to
heavily soiled.
SYNTHETICS
Suitable for washing moderately soiled garments made of
synthetic bres (e.g. polyester, polyacrylic, viscose, etc.) or
mixed synthetic-cotton bres.
MIXED
A 40°C cycle for washing cotton and synthetic garments
together. Suitable for lightly soiled underwear.
ECO COTTON
Suitable for washing moderately soiled cotton garments.
At 40°C and 60°C it is the standard cycle for washing cotton
garments, and is the most ecient in terms of combined
water and electricity consumption.
WHITE COTTON
For heavily soiled whites and resistant colours.
SPORT
A cycle designed for washing lightly soiled sports clothing
(tracksuits, shorts, etc.); for best results, we recommend not
exceeding the maximum load indicated in the “Wash Cycle
Table”. We recommend using liquid detergent and adding
the amount suitable for a half-load.
1
10
2 3
6
9
11
4
87
5
EN
User manual
7
DUVET
For washing clothing padded with goose down, such as
double or single duvets (weighing under 3.5 kg), cushions
or down jackets. Duvets should be loaded into the drum
with their edges folded inwards and no more than ¾ of the
total drum volume should be used up. For best results, it
is advisable to use liquid detergent to be poured into the
detergent drawer.
WOOL - WOOLMARK APPAREL CARE
- BLUE:
The “Wool” wash cycle is approved by
the Woolmark Company for washing
wool garments classied as “hand-washable”, provided
that the wash complies with the instructions appearing
on the garment’s label and with those provided by the
manufacturer of this washing machine. (M1127)
ANTI ODOUR
Use this cycle (for synthetic fabrics) to wash garments with
bad odours (e.g. smoke, sweat, fried food). The cycle is
designed to remove bad odours while preserving the fabric
bres.
RINSE + SPIN
Designed for rinsing and spinning.
SPIN + DRAIN
Designed to spin and drain the water.
ANTI-STAIN
This option allows for selecting the type of dirt so as
to optimally adjust the cycle for removing the stains. The
following types of dirt can be selected:
Food : for stains caused by foodstus and beverages, for
example.
Work : for grease and ink stains, for example.
Outdoor : for mud and grass stains, for example.
! The wash cycle duration varies according to the type of
selected dirt.
EXTRA RINSE
By selecting this option, the eciency of the rinse is
increased and optimal detergent removal is guaranteed. It is
particularly useful for sensitive skin.
EASY IRON
By selecting this function, the wash and spin
cycles will be modied in order to limit the formation of
creases. At the end of the cycle the washing machine’s
drum will rotate slowly; the EASY IRON and START/PAUSE
indicator lights will ash and the phase will remain lit
steady. To end the cycle, press the START/PAUSE button
or the EASY IRON button.
OPTIONS
! If the selected option is not compatible with the set wash cycle, the indicator light will ash and the option will not be activated.
! If the selected option is not compatible with another previously selected option, the indicator light will ash accompanied by a
buzzer (3 beeps), and only the latter option will be activated; the indicator light corresponding to the activated option will turn on.
DELAY START
To set a delayed start for the selected cycle, press the
corresponding button repeatedly until the desired delay
period has been reached (3h-6h-9h). When the button is
pressed for the fourth time, the option will deactivate.
Once the START/PAUSE button has been pressed, the
delay time can only be modied by decreasing it until the
set cycle is launched.
40°
60°
TEMPERATURE
Each wash cycle has a pre-dened temperature. To
modify the temperature, press the
40°
60°
button.
SPIN
Each wash cycle has a pre-dened spin speed. To
modify the spin speed, press the button.
User manual
8
PUSH & WASH
This function allows for starting a wash cycle even when the machine is switched o without having to press the ON/OFF
button in advance or, after switching the machine on, without having activated any other button and/or selector knob
(otherwise the Push & Wash cycle will be deactivated). To start the Push & Wash cycle press and hold the relative button for 2
seconds. The lit indicator light indicates that the cycle has started. This wash cycle is ideal for cotton or synthetic fabrics, as it
washes at a temperature of 30°C and a maximum spin speed of 1,000 rpm. Max load 4 kg (cycle duration 45’).
How does it work?
1. Load the laundry (cotton and/or synthetic garments) and
close the door.
2. Pour the detergent and additives.
3. Start the cycle by pressing and holding the Push & Wash
button for 2 seconds. The relevant indicator light will turn
green and the door will lock (the symbol lights up).
N.B.: starting the wash cycle through the Push & Wash
button activates an automatic non-customisable cycle
recommended for cotton and synthetic fabrics. This cycle
does not allow for setting any additional options.
To open the door while an automatic cycle is under way,
press the START/PAUSE button; if the locked door symbol
is o, the door may be opened. Press the START/PAUSE
button again to restart the cycle from the point at which it
was interrupted.
4. Once the programme is nished, the indicator light
turns on.
EN
User manual
9
ON/OFF
button: switches the washing machine on and o.
WASH CYCLE SELECTOR KNOB:
Used to set the desired wash cycle (see “Table of
wash cycles”).
START/PAUSE
Button with indicator light: starts or temporarily
interrupts the wash cycles.
N.B.: To pause the wash cycle in progress, press this button;
the corresponding indicator light will ash orange, while the
indicator light for the current wash cycle phase will remain
lit in a xed manner. If the DOOR LOCKED indicator light is
switched o, the door may be opened (wait approximately
3 minutes). To start the wash cycle from the point at which it
was interrupted, press this button again.
CHILD LOCK
To activate the control panel lock, press and hold
the button for approximately 2 seconds. The lit symbol
signals that the control panel is locked. This prevents wash
cycles from being modied accidentally (except for the ON/
OFF button), especially if there are children in the home.
To deactivate the control panel lock, press and hold the
button for approximately 2 seconds.
FUNCTIONS
INDICATOR LIGHTS
The indicator lights provide important information.
This is what they can tell you:
Delayed start
If the DELAY TIMER function has been activated (see
“Personalisation”), after the wash cycle has been started the
indicator light corresponding to the selected delay period
will begin to ash:
As time passes, the remaining delay will be displayed and
the corresponding indicator light will ash:
The set programme will start once the selected time delay
has expired.
Wash cycle phase indicator lights
Once the desired wash cycle has been selected and has
begun, the indicator lights switch on one-by-one to indicate
which phase of the cycle is currently in progress.
Wash
Rinse
Spin
Drain
End of Wash Cycle
Door locked indicator
When lit, the symbol indicates that the door is locked. To
prevent any damage, wait until the symbol turns o before
opening the door.
To open the door while a cycle is in progress, press the
START/PAUSE button; if the indicator light is o, the door
can be opened.
User manual
10
WASH CYCLE TABLE
Maximum load 7 kg
Power input in o mode 0.5 W / in left-on mode 8 W
Detergents and
Additives
Recommended
detergent
Residual
dampness %
Energy con-
sumption kWh
Total water l
Wash cycle Temperature Maximum
spin
(r.p.m.)
Maximum
load
(kg)
Duration
(minutes)
Wash Fabric
softener Powder Liquid
Default Range
1 Daily cotton 30°C – 30°C 1000 3.5 100 –– – –
2 Daily synthetics 30°C – 30°C 1000 3.5 90 –– – –
3 Coloureds 30°C – 30°C 1000 3.5 95 –– – –
4 Delicates 30°C – 30°C 0 1.0 80 –– – –
5 Rapid 30min 30°C – 30°C 800 3.5 30 –70 0.16 33
6 Cotton (2) 40°C – 60°C 1000 7.0 220 62 0.98 75
7 Synthetics (3) 40°C – 60°C 1000 3.5 195 33 0.75 72
8 Mixed 40°C – 40°C 1000 7.0 100 –– – –
9Eco cotton (1) 60°C 60°C 1000 7.0 275 62 1.01 52.5
40°C 1000 7.0 220 62 0.98 75
10 White cotton 60°C – 90°C 1000 7.0 130 – – –
11 Sport 30°C – 30°C 600 3.5 55 –– – –
12 Duvet 30°C – 30°C 1000 2.0 110 –– – –
13 Wool 40°C – 40°C 800 1.5 70 –– – –
14 Anti odour 40°C – 40°C 1000 3.0 100 –– – –
Rinse + Spin – – 1000 7.0 50 – – – – – –
Spin + Drain * – – 1000 7.0 10 – – – – – – –
Required dosage Optional dosage
The cycle duration indicated on the display or instruction manual
is an estimate based on standard conditions. The actual duration
may vary in relation to several factors, such as the temperature
and pressure of the incoming water, ambient temperature,
amount of detergent, load quantity and type, load balancing and
any additional options selected.
Test wash cycle in compliance with regulation 1061/2010:
1) This cycle is designed for normally soiled cotton loads and
is the most ecient in terms of both electricity and water
consumption; it should be used for garments washable at 60°C
or at 40°C. The actual washing temperature may dier from the
indicated value.
For all testing institutes:
2) Long cotton cycle: set cycle 6 at a temperature of 40°C.
3) Long synthetics cycle: set cycle 7 at a temperature of 40°C.
* By selecting the cycle and excluding the spin cycle, the
washing machine will drain only.
ACCESSORIES
Contact our Technical Assistance Service to check whether the
following accessories are available for this washing machine
model.
Stacking kit
With this accessory you can secure the tumble dryer to the
upper part of your washing machine to save space and
facilitate loading and unloading of the tumble dryer.
EN
User manual
11
HOW TO USE THE APPLIANCE
FIRST TIME USE
Once the appliance has been installed, and before it is used
for the rst time, run a wash cycle with detergent and no
laundry, by setting the “Auto-Clean” cycle.
DAILY USE
PREPARING THE LAUNDRY
Empty the pockets
• Objects such as coins or lighters can damage the
washing machine and the drum. Check all buttons.
Divide the laundry according to
• Type of fabric (cotton, mixed bres, synthetics, wool,
garments to be hand-washed). Colour (separate coloured
garments from whites, wash new coloured garments
separately). Delicates (small garments – such as nylon
stockings – and items with hooks – such as bras: insert
them in a fabric bag).
RUNNING A WASH CYCLE
Rapid programming
1. Open the door. Load the laundry while making
sure not to exceed the maximum load quantity
indicated in the cycle table.
2. Pull out the detergent dispenser drawer and pour
the detergent into the relevant compartments as
described in “DETERGENT DISPENSER DRAWER”
section.
3. Close the door.
4. Press the PUSH & WASH button to start the
wash cycle.
Traditional programming
1. Turn the washing machine on by pressing the ON/
OFF button. All the indicator lights will light up for a
few seconds, then only the lights corresponding to the
settings for the selected wash cycle will remain lit; the
START/PAUSE indicator light will also ash.
2. Open the door. Load the laundry while making
sure not to exceed the maximum load quantity
indicated in the Wash Cycle Table.
3. Pull out the detergent dispenser drawer and pour
the detergent into the relevant compartments as
described in “DETERGENT DISPENSER DRAWER”
section.
4. Close the door.
5. Set the WASH CYCLE knob to the desired
cycle.
6. Modify the temperature and/or spin: pressing the
40°
60°
button allows for gradually reducing the temperature
down to the cold wash level (20°C). The spin speed may
be progressively reduced by pressing the button,
until it is completely excluded (the “ ” setting. If these
buttons are pressed again, the maximum values are
restored.
7. Select the desired options.
- If the selected option is not compatible with the set wash cycle, the
indicator light will ash and the option will not be activated.
- If the selected option is not compatible with another previously
selected option, the indicator light will ash accompanied by a
buzzer (3 beeps), and only the latter option will be activated; the
indicator light corresponding to the activated option will turn on.
8. Press the START/PAUSE button to start the wash cycle;
the relative indicator light will light up steady green and
the door will lock ( symbol on).
PAUSING A CYCLE
To pause the wash cycle, press the START/PAUSE button
again; the indicator light will ash amber. If the symbol is
not lit, the door may be opened. To start the wash cycle from
the point at which it was interrupted, press the START/PAUSE
button again.
OPENING THE DOOR, IF NECESSARY
Once a cycle starts, the symbol turns on to signal that the
door cannot be opened. While a wash cycle is running, the
door remains locked. To open the door while a cycle is under
way, for example, to add or remove garments, press the
START/PAUSE button to pause the cycle; the indicator light
will ash amber. If the symbol is not lit, the door may be
opened. Press the START/PAUSE button again to continue
the cycle.
CHANGING A RUNNING WASH CYCLE
To change a wash cycle while it is in progress, pause the
washing machine using the START/PAUSE button (the
relative indicator light will ash amber), then select the
desired cycle and press the START/PAUSE button again.
! To cancel a cycle that has already begun, press and hold
the ON/OFF button. The cycle will be stopped and the
machine will switch o.
User manual
12
END OF THE CYCLE
Once the cycle terminates the indicator light will light
up; when the indicator light switches o, the door may
be opened. Open the door, unload the laundry and switch
o the machine. If you do not press “ON/OFF” button, the
washing machine will switch o automatically after about
a half of an hour. Close the water tap, open the door and
unload the washing machine. Leave the door ajar to allow the
drum to dry.
! If you wish to cancel a cycle which has already begun,
press and hold the “ON/OFF” button. The cycle will be
stopped and the machine will switch o.
Load balancing system
Before every spin cycle, to avoid excessive vibrations before
every spin and to distribute the load in a uniform manner, the
drum rotates continuously at a speed which is slightly greater
than the washing rotation speed. If, after several attempts,
the load is not balanced correctly, the machine spins at a
reduced spin speed. If the load is excessively unbalanced, the
washing machine performs the distribution process instead
of spinning. To encourage improved load distribution and
balance, we recommend small and large garments are mixed
in the load.
HINTS AND TIPS
RULES FOR SEPARATING LAUNDRY
• Fabric type / indications on label (cotton, mixed bres,
synthetic, wool, handwash items)
• Colour (separate coloured garments from whites, wash
new coloured items separately)
• Size (wash items of dierent sizes in the same load to
improve washing ecacy and weight distribution in the
drum)
• Delicates (place small items – such as nylon stockings –
and garments with clasps – such as braziers – in a laundry
bag or in a pillow case with a zip).
WASH SYMBOLS ON GARMENT LABELS
The value given in the tub symbol is the maximum
temperature possible for washing the garment.
Normal mechanical action
Reduced mechanical action
Much reduced mechanical action
Hand wash only
Do not wash
CLEAN THE WATER FILTER REGULARLY
• This is needed to prevent the lter from blocking and
preventing the water from draining correctly.
HOW MUCH DOES YOUR LAUNDRY WEIGH?
• 1 sheet 400-500 g
• 1 pillow case 150-200 g
• 1 tablecloth 400-500 g
• 1 bathrobe 900-1.200 g
• 1 towel 150-250 g
EN
User manual
13
DISCONNECT THE WATER AND POWER
SUPPLIES
Close the water tap after every wash. This will limit wear on
the hydraulic system inside the washing machine and help to
prevent leaks.
Unplug the washing machine when cleaning it and during all
maintenance work.
CLEAN THE WASHING MACHINE
The outer parts and rubber components of the appliance
can be cleaned using a soft cloth soaked in lukewarm soapy
water. Do not use solvents or abrasives.
The washing machine has a “Auto-cleaning” cycle for its
internal parts; it must be run without any load in the drum.
To optimise this cycle, it is possible to use either detergent
(10% of the quantity specied for lightly soiled garments)
or special additives to clean the washing machine. We
recommend running a cleaning cycle every 40 wash cycles.
To start the cycle press buttons and simultaneously
for 5 seconds.
The cycle will start automatically and will run for about 70
minutes. To stop the cycle, press the START/PAUSE button.
A
B
CLEANING THE DETERGENT DISPENSER
DRAWER
To remove the drawer, press lever (1) and pull the drawer
outwards (2) (see gure). Wash it under running water; this
procedureshould be repeated frequently.
2
1
CARE FOR THE DOOR AND DRUM
Always leave the porthole door ajar in order to prevent
unpleasant odours from forming.
CLEAN THE PUMP
The washing machine is tted with a auto-cleaning pump
that does not require any maintenance. Small items (such as
coins or buttons) may sometimes fall into the protective pre-
chamber situated at the base of the pump.
! Make sure the wash cycle has ended and unplug the
appliance.
To access the pre-chamber:
1. Remove the cover panel on the front of the machine by
rst pressing it in the centre then pushing downwards on
both sides to extract it;
2.
1
23
Loosen the drainage pump cover by turning it anti-
clockwise: it is normal for some water to leak out;
3. Clean the inside thoroughly;
4. Screw the cover back on;
5. Put the panel back in place, making sure the hooks slot in
place before pushing the panel onto the appliance.
CHECK THE WATER INLET HOSE
Check the water inlet hose at least once a year. If it is cracked
or broken, it must be replaced: during wash cycles, the high
pressure of the water could suddenly split the hose open.
! Never use hoses that have already been used.
CLEANING & MAINTENANCE
Before performing cleaning and maintenance, switch the washing machine o and disconnect it from the mains
power. Do not use ammable liquids to clean the washing machine.
User manual
14
TROUBLESHOOTING
The washing machine may occasionally fail to work. Before contacting the Technical Assistance Service, make sure that the
problem cannot be easily solved using the following list.
Anomalies Possible causes / Solution
The washing machine does
not start.
The appliance is not plugged into the socket, or not suciently to make contact.
There is no power in the house.
The wash cycle does not start.
The washing machine door is not closed properly.
The ON/OFF button has not been pressed.
The START/PAUSE button has not been pressed.
The water tap has not been opened.
A delay has been set for the start time.
The machine does not ll with
water or the indicator light
for the rst wash cycle stage
ashes rapidly.
The water inlet hose is not connected to the tap.
The hose is bent.
The water tap has not been opened.
There is no water supply in the house.
The pressure is too low.
The START/PAUSE button has not been pressed.
The washing machine
continuously loads and
unloads water.
The drain hose is not tted between 65 and 100 cm from the oor.
The free end of the hose is immersed in water.
The wall drainage system does not have a breather pipe.
If the problem persists even after these checks, turn o the water tap, switch the appliance o and contact the
Technical Assistance Service. If the home is on one of the upper oors of a building, there may be problems
relating to back-siphonage, causing the washing machine to ll with water and drain continuously. Special
anti-siphon valves are available in shops and help to prevent this inconvenience.
The washing machine does
not drain or spin.
The cycle does not include drainage: with certain cycles it must be started manually.
The drain hose is bent.
The option is enabled: to complete the wash cycle, press the START/PAUSE button.
The drainage duct is clogged.
The washing machine
vibrates a lot during the spin
cycle.
The drum was not unlocked correctly during installation.
The washing machine is not level.
The washing machine is tucked between furniture cabinets and the wall.
The washing machine leaks.
The water inlet hose is not screwed on properly.
The detergent dispenser drawer is obstructed.
The drain hose is not properly attached.
The “Options” lights and the
START/PAUSE indicator light
ash while one of the wash
cycle progress and DOOR
LOCKED lights are lit in a xed
manner.
Switch o the machine and unplug it, wait for approximately 1 minute and then switch it back on again.
If the problem persists, contact the Technical Assistance Service .
There is too much foam.
The detergent is not suitable for machine washing (it should be marked with “for washing machine use” or
“hand wash and machine wash” or similar).
Too much detergent was used.
The Push & Wash function
does not activate.
After switching on the machine, a control other than Push & Wash was activated. Switch the machine o and
press the Push & Wash button.
EN
User manual
15
TRANSPORT AND HANDLING
Do not lift the washing machine by gripping it from the upper section.
1. Unplug the appliance and close the water tap.
2. Check that the door and detergent dispenser drawer are
tightly closed.
3. Detach the lling hose from the water tap then detach
the drain hose.
4. Empty all the water remaining in the hoses and secure
the latter so that they do not get damaged during
transport.
5. Apply the transport bolts back on. Repeat, in reverse
order, the transport bolt removal procedure described in
the “Health & Safety and Installation Guides”.
Important: Do not transport the washing machine without
having xed the transport bolts.
User manual
16
SERVICE
BEFORE CONTACTING THE TECHNICAL ASSISTANCE SERVICE
• Check whether you can solve the problem alone (see
“Troubleshooting”).
• Restart the wash cycle to check whether the problem has
been solved.
• If this is not the case, contact an authorised Technical
Assistance Centre.
! Always request the assistance of authorised technicians.
CONTACT OUR TECHNICAL ASSISTANCE SERVICE
If after the above checks the fault still occurs, get in touch
with the nearest Technical Assistance Service (See phone
number in the warranty booklet)
Have the following information to hand:
• the type of problem;
• the appliance model (Mod.);
• the serial number (S/N).
This information can be found on the data plate applied to
the rear of the washing machine, and can also be found on
the front of the appliance by opening the door.
XXXXXXXXXX
17
1a
1b
x 4
17 mm - 0.67 inch
12 mm - 0.47 inch
3
4
x 1
x 1
2
1c
1d
x 4
1
2 cm - 0,7 inch
Installation guide
18
859991536030EN
max 2,0 cm
max 0,8 inch
ext nn
x 4
m
a
x
2
,
5
m
/
8
,
2
f
e
e
t
max 100cm / 39 inch
min 60cm / 24 inch
A
max 100cm / 39 inch
min 60cm / 24 inch
B
Installation guide