Indesit YT M11 83K RX EU User Manual
Displayed below is the user manual for YT M11 83K RX EU by Indesit which is a product in the Tumble Dryers category. This manual has pages.
Related Manuals
If the door is opened during the cycle, to restart it, close the door and
press the button START/PAUSE. This programme does not allow to set
other options.
OPENING OF THE DOOR DURING THE CYCLE
During operation, it is possible to open the door. After having closed it,
press the button Start/Pause again to restart the dryer.
PROGRAMMES
Eco cotton kg Max*
Standard cotton programme, suitable to dry normally wet
cotton laundry. Most ecient programme in terms of energy
consumption for drying cotton laundry. The values on the Energy
Label are based on this programme.
Synthetics kg 4
For drying laundry made of synthetic bres.
Mixed kg 4
This programme is ideal for drying cotton and synthetic fabrics
together.
Mini synthetics kg 2
Eco-drying of small laundry loads.
Mini cotton kg 2
Eco-drying of small laundry loads.
Delicates kg 2
For drying delicate laundry requiring a gentle treatment.
Wool kg 1
Programme for drying wool clothing. It is advisable to turn the
garments inside out before drying. Leave to dry naturally the heaviest
edges that are still damp.
FIRST TIME USE
Make sure that the water tank is correctly inserted. Make sure
that the drain hose on the back of the dyrer is properly xed,
either to the dryers's water tank or to the domestic sewage
system.
The dryer must be installed in a room with a temperature
ranging between 5°C and 35°C to ensure proper operation.
Before you use your dryer ensure that it has been in a upright
position for at least 6 hours.
DAILY USE
Doing this will keep your machine working at its BEST!
Remember to empty your water tank after each drying cycle.
Remember to clean your lters after each drying cycle. (Refer to
section Care & Maintanence).
1. Open the door and load garments. Always refer to instructions
on clothing labels and the max loads indicated in the programme
section. Empty pockets. Make sure garments do not get caught
between the door and/or the door lter.
2. Close the door.
3. Press the button On/O .
4. Select the programme according to the laundry type.
5. Select the options, if necessary.
6. To start the cycle, press the Start/Pause button.
7. At the end of the drying cycle, a buzzer will beep. An indicator on
the control panel signals the end of the cycle. Pull the load out
immediately to prevent the formation of creases on laundry.
8. Turn the machine o by pressing the button On/O, open the
door and pull clothing out. If the machine is not switched o
manually, after about a quarter of an hour from the cycle end, the
appliance turns o automatically to save energy.
If this last stage is not carried out immediately, some machines
and/or some programmes/options are equipped with Crease Care
system. For some hours, after the end of drying, the drum rotates at
regular intervals to prevent the formation of creases.
In case of power failure, it is necessary to press the button Start/
Pause to restart the cycle.
PUSH & GO
This function serves to start a cycle, after machine switching on,
without enabling any further button an/or knob (the programme
PUSH & GO will be deactivated instead).
It is always necessary to follow the points 1, 2, and 3
concerning the daily use.
To start the cycle Touch & GO, keep the button pressed. The light
on signals that the cycle is started. The cycle is suitable for cotton
and synthetic textiles. Max. load 4 kg. (Cycle duration 131’).
*MAX LOAD 8 Kg (Dry load)
CARE LABEL
Always check the care labels, especially when placing garments in
the tumble dryer for the rst time. Below are the most commonly
used symbols:
May be tumble dried.
Do not tumble dry.
Tumble dry – high heat.
Tumble dry – low heat.
You can download the Safety Instructions, User Manual, Product Fiche and Energy data by:
• Visiting our website - docs.indesit.eu
• Using QR Code
• Alternatively, contact our After-sales Service (See phone number in the warranty booklet). When
contacting our After-sales Service, please state the codes provided on your product’s identi cation plate.
THANK YOU FOR BUYING A INDESIT PRODUCT.
In order to receive a more complete assistance,
please register your product on
www.indesit.eu/register
EN
Quick guide
Before using the appliance carefully read the Safety Instructions.
xxxxxxxxxxxx
xxxx
CONTROL PANEL
1 ON/OFF button (Reset if long pressed)
2 Programme selection knob
3 Start/Pause
4 Push & Go
Options buttons*
5 Dryness level
6 Start delay
7 Timed drying
8 Cycle end
9 Light drying (Key lock if long pressed)
10 Crease care (Mute if long pressed)
*Note: some models may have the wording in full instead of the icons
INDICATORS
Dryness level: Iron dry - Hanger dry - Cupboard dry - Extra dry -
Cycle phase: Dry - Cool tumble - END End of cycle -
Empty water tank Clean door lter Clean bottom lter
Refer to Troubleshooting section: Failure: Call after sales service -
DEMO
Demo mode
start delay
1
3
2
4
10
8
9
567
DEMO
3’’
3’’
OPTIONS BUTTONS
These buttons serves to personalise the selected programme
according to personal requirements.
Not all options are available for all programmes. Some options
are incompatible with the ones previously set. The buzzer and/or
blinking indicators will signal the incompatibility. If the option is
available, the option indicator will stay on. Some options may be
kept in the memory of the programme if selected in the previous
drying.
Refresh
A short programme suitable for refreshing bres and
garments by means of fresh air. Do not use with garments
that are still wet. It can be used on with any load size but is
more eective with small loads. The cycle duration is about 20
minutes.
Shirts kg 3
This is a programme for Shirts made from cotton or cotton
blend/synthetics.
Duvet '
Programme intended to dry bulky garments, as single duvet.
Baby kg 2
A programme intended to dry garments and linen of
new-born babies (cotton and chenille), as well as delicate
garments. Do not dry garments having plastic covering.
Sport kg 4
For drying sports garments made of synthetics or cotton
blends.
Sport shoes 1 pair
This programme is intended to dry a pair of sport shoes.
The shoes must be washed and spun at a minimum spin speed
of 400 revolutions. It is necessary to use the apposite shoe rack
supplied. Only dry shoes made of synthetic material or canvas.
Smart iron
This cycle allows to extend the bres of garments thus
making ironing and folding easier. Do not use in case of
garments that are still wet. Suitable for small loads of cotton
textiles or cotton blends.
45’
Xpress 45' kg 1
This is a quick timed programme, ideal for drying garments
spun at high speed in the washing machine, e.g. the shirts used
in a working week.
OPTIONS
After selecting the programme, the various options can be
set, if necessary.
Dryness level
Press the related button several times to obtain a dierent
level of residual moisture on garments. An indicator signals the
level being selected.
Iron dry: a very delicate ironing. Suitable for making ironing of
garments easier immediately after the end of the cycle.
Hanger dry: a level intended for delicate garments ready to
be hanged.
Cupboard dry: the garments are ready to be folded and put
away.
Extra dry: used for garments to be worn at the end of the
cycle.
Timed drying
This option allows to set the drying time. Press the
corresponding button to set the required time for drying. An
indicator on the control panel signals the time being selected.
Start delay
This option allows you to set the delay of the cycle start. Press
the corresponding button several times to obtain the required
delay. After having reached the max. settable time, the option is
reset by pressing the button again. An indicator on the control
panel signals the time being selected. After having pressed the
button Start/Pause, the machine signals the remaining time for the
cycle start. In case of door opening, after closing, it is necessary to
press the button Start/Pause.
Crease care
This option add a crease treatment at the end of the cycle by
means of a periodic rotation of the drum (duration up to 10 hours).
It is particularly suitable when it is not possible to remove the
laundry as soon as the drying ends. If this option is used together
with the Start Delay, the crease treatment is added also in the
Start Delay phase. This option remains in memory if selected in
the previous drying.
Light dry
Enables a more gentle treatment of the laundry by reducing
the drying temperature.
Mute
This option turns o all sounds of control panel. Only
warnings remain active.
• to activate the option, keep the button pressed until the
indicator goes on.
• to disable the option, keep the button pressed until the indicator
goes o.
Key lock
This option makes all machine controls inaccesible, except
the button On/O. When the machine is on:
• to activate the option, keep the button pressed until the
indicator goes on.
• to disable the option, keep the button pressed until the indicator
goes o.
This option remains in memory if selected in the previous drying.
Cycle end
This option activates a prolonged buzzer at the end of the
cycle. Enable it if you are not sure to hear the normal sound at the
end of the cycle. This option remains in memory if selected in the
previous drying.
USE OF SHOE RACK
Remove the door lter and place
the shoe rack. Put shoelaces
into the shoes with the shoe tips
facing downwards and the soles
frontwards. Do not add garments
or other shoes into the drum.
Position the door lter back in place
at the end of drying.
The duration of these programs will depend on the size of the
load, types of textiles, the spin speed used in your washer and
any extra options selected. In machines equipped with display,
the duration of the cycles is shown on the control panel. The
remaining time is constantly checked and adjusted during the
drying cycle to show the best possible estimate.
CARE AND MANTENANCE
Unplug the dryer during the cleaning and maintenance
procedures.
Emptying the water tank after each cycle (see Fig. A).
Pull the container out of the dryer and and empty it into a sink
or other suitable drain, then place it back. Do not use the dryer
without having inserted the container back in place.
Cleaning the door lter after each cycle (see Fig. B).
Pull the lter out and clean it by removing the lint from the lter
surface under running water or using a vacuum cleaner. For optimal
performance, dry up all the lters before inserting them back in
place. Do not use the dryer without having reinserted the lter in
place.
Remove the door lter as described below:
1. Open the door and pull upwards.
2. Open the lter and remove lint from all its parts. Replace it
correctly. Ensure it is completely inserted ush with the dryer seal.
Cleaning the bottom lter when the relevant indicator
turns on (see Fig. C).
Pull the lter out and remove the lint from its surface by washing
it under runing water or by using a vacuum cleaner. However,
it is advisable to clean this lter after each cycle to optimise
drying performance. Do not use the dryer without having
inserted the lter in place rst.
Remove the bottom lter as described below:
1. Open the lower door.
2. Take the handle and pull the lower lter out.
3. Open the rear side of the lter and remove the lint from the
inner surface of the mesh.
4. Clean the bottom lter chamber avoiding the direct contact
with the leaves.
5. Close the rear side of the lower lter and place it back by
checking it is perfectly integrated in place.
6. Lower the lter handle and close the bottom door.
7. Make sure the air intake is free.
The lters are essential parts for drying. They are intended
to collect the lint formed during drying process. In case
of clogged lters, the air ow inside the dryer would be
seriously aected: the drying times would be longer, the
energy consumption would increase and the dryer could be
damaged. If these procedures are not carried out properly,
the dryer may not start.
PRODUCT DESCRIPTION
1. Water Tank
2. Air Intake
3. Bottom lter
4. Door lter
TRANSPORT AND HANDLING
Never lift the dryer by holding it at the worktop.
1. Unplug the dryer.
2. Make sure that door and water tank are properly closed.
3. If the drain hose is connected to your sewage system, x the
drain hose on the rear of the dryer again (see Installation Guide).
Heat Pump System
The heat pump contains uorinated greenhouse gases,
contained in a hermetically sealed unit. This sealed unit contains
0.43 kg of the F gas R134a. GWP = 1430 (1 t CO2).
Power consumption
o-mode (Po) - Watts 0.50
left-on mode (Pl) - Watts 1.00
Programs Kg kWh Minutes
Eco Cotton * 8 1.42 165
Eco Cotton 4 0.78 96
Synthetics 4 0.94 113
*This is the reference programme for the energy label and suitable to
dry normal wet cotton laundry. This is the most ecient programme
in terms of energy consumption for drying wet cotton laundry.
(Standard/Default starting conguration)
You can download the Safety Instructions, User Manual, Product Fiche and Energy data by:
• Visiting our website - docs.indesit.eu
• Using QR Code
• Alternatively, contact our After-sales Service (See phone number in the warranty booklet). When
contacting our After-sales Service, please state the codes provided on your product’s identi cation plate.
THANK YOU FOR BUYING A INDESIT PRODUCT.
In order to receive a more complete assistance,
please register your product on
www.indesit.eu/register
EN
Quick guide
Before using the appliance carefully read the Safety Instructions.
xxxxxxxxxxxx
xxxx
AB
1
42
3
C
TROUBLESHOOTING
Before contacting the Service Centre, refer to the table below. Often the malfunctions are minor and can be solved in few minutes
Malfunction
Possible cause
Solution
The tumble
dryer does not
turn on.
The plug is not inserted into the socket.
Insert the plug into the socket.
The plug is faulty. Try to plug another appliance in the same socket. Do not use
connecting electrical devices to the socket, as adapters or extensions
A power failure occurred. Await the reactivation of the power supply.
The tumble
dryer does not
start
The door is open.
Close the door.
A time delay for the cycle start was set. For machines equipped with this function: await the end of the delay
set or switch the machine o to reset it. Refer to the section Options.
The button Start/Pause was not pressed to start
the program.
Press the button Start/Pause.
The function Key Lock was enabled (in case of
machines equipped with this option).
Refer to the option section and, if the Key Lock is present, disable it.
Switching the machine o is not enough to disable this option.
The drying
times are very
long
An appropriate maintenance was not carried
out.
Refer to the section Care & Maintenance and perform the operations
described.
The programme, the time and/or the drying
level set are not suitable for the type and the
amount of load inserted into the dryer.
Refer to the section programmes and options to nd the programme
and the options most suitable for the type of load.
The garments are too wet. Carry out a washing cycle with higher spin speed to remove as much
water as possible.
The dryer may be overloaded. Refer to the programme section to check the max. load for each
programme.
Room temperature. The drying time may be longer if the room temperature falls outside the
14–30°C range.
The programme
did not end.
A power failure occurred might have occurred.
In case of power failure, it is necessary to press the button Start/Pause
to restart the cycle.
Lights on or ashing
Water tank The water tank is full. Emtpy the water tank. Refer to the section Care & Maintenance.
Door lter
and/or bottom
lter*
Failure of the air ow necessary for machine
operation.
Clean the door lter and the bottom one and check whether air
intake is free. Carrying out these operations improperly may cause
damages.
Bottom lter* The bottom lter requires cleaning. Clean the bottom lter. Refer to section Care & Maintanence.
DEMO
The cycle lasts
few minutes.
The dryer is in DEMO mode. The DEMO
indicator is on.
Disable the DEMO mode. The following actions must be carried out
in sequence, without breaks. Switch the machine on and then switch
it o again. Press the Start/Pause button until the buzzer is heard.
Switch the machine on again. The “DEMO” indicator ashes and then
turns o .
The presence
of wrench
symbol signals a
malfunction.
The machine sensors detected a failure.
Switch the dryer o and unplug it. Open the door immediately and
pull laundry out, to allow the heat to dissipate. Wait for about 15
minutes. Reconnect the dryer to the power supply, load the laundry
and restart the drying cycle. If the problem still occurs, contact
the After-Sales Service Centre and communicate the letters and
digits ashing on the display.
For instance: F3 and E2
*Note: some models are self-cleaning and not equipped with bottom lter. Please refer to the section Care & Maintenance.
You can download the Safety Instructions, User Manual, Product Fiche and Energy data by:
• Visiting our website - docs.indesit.eu
• Using QR Code
• Alternatively, contact our After-sales Service (See phone number in the warranty booklet). When
contacting our After-sales Service, please state the codes provided on your product’s identi cation plate.
THANK YOU FOR BUYING A INDESIT PRODUCT.
In order to receive a more complete assistance,
please register your product on
www.indesit.eu/register
EN
Quick guide
Before using the appliance carefully read the Safety Instructions.
xxxxxxxxxxxx
xxxx