JPL JPL-Connect-1 User Manual
Displayed below is the user manual for JPL-Connect-1 by JPL which is a product in the Headphones & Headsets category. This manual has pages.
Related Manuals
Important Safety Instructions
This headset is very easy to use and setup. For optimal use, we still
recommend that you read this user guide carefully before using the
headset for the rst time.
Unpacking
Remove your headset from its packaging and ensure you have the
correct specied accessories. Retain the headset box for storage
of your unit, and also in the event that it needs to be returned for
servicing or repair.
Safety
For your own safety, this product should only be used with CE
ACA and RoHS approved equipment. Using this headset with non
approved equipment can void this products warranty.
Maintenance
To gain optimal performance, hygiene and life-span from your
headset, replace all consumable items; - ear cushions, microphone
foam wind shield (if applicable) every 6 months.
Environmental Notice
This headset has been made to CE, RoHS and WEEE standards.
In the interest of recycling raw materials, please do not dispose
of this headset in the household waste at the end of its useful
life. Disposal can take place at approved recycling or disposing
locations in accordance with local regulations.
Warning
Ensure that all electrical connections (including extension leads
and interconnections between pieces of equipment) are properly
made and in accordance with the relevant manufacturers
instructions.
• Do not continue to operate the equipment if you are in any
doubt about it working normally, or if it is damaged in any way.
Disconnect from your telephone equipment and consult your
dealer.
• Do not allow electrical equipment to be exposed to rain or
moisture.
• Never push anything into holes, slots or any other opening on
your headset as this could result in fatal electrical shock.
• Do not open the headset housing as doing so will void the
warranty.
• Never guess or take chances with electrical equipment.
• Do not use this equipment to report a gas leak while you are in
the vacinity of a gas leak.
• Telephone headsets are capable of producing high levels of
sound. Prolonged exposure to high sound levels can cause
damage to hearing.
• Never allow small children to play with the headset - small parts
may be a choking hazard.
Connecting and using your headset
Does your desk phone have a dedicated headset connection
port?
If it does, simply connect your headset’s cable to your chosen bottom
lead, then connect the bottom lead to the dedicated port on your desk
phone.
If you nd that when the headset is connected to the phone it is not
working as expected then it is very likely you are using an incompatible
bottom lead.
There are various bottom leads available, these are all designed to
connect your headset to specic brands of desk phone, ensuring
whatever your setup, your headset will be compatible.
Please contact your dealer to attain the correct bottom lead for your
desk phone.
What do you do if you want to connect your headset to a PC:
Your headset requires a USB cable. In the event that you do not have this
adapter cable, please contact the supplier of this headset. They will be
able to provide the correct adapter cable for your headset and PC.
Adjusting the Headband
Place the headset receiver to your ear and set the T-bar above your other
ear. Adjust the headband until it is comfortable, ideally ensuring there is
virtually no pressure felt on the ear.
The headset can be worn on either
side. To change the microphone side,
simply rotate the microphone boom
270 degrees to the other side.
Adjusting the Microphone Boom
To avoid low or distorted sound, and to
provide clear and crisp telephone calls, the
microphone should be positioned within
30-40 mm of your mouth.
The microphone boom will move in a variety
of directions to ensure the best t.
Adjusting the Clothing Clip
Your new headset is supplied with a clothing clip to allow comfortable
tting of your headset without the cable getting caught or inadvertently
pulled.
The clothing clip should be fastened at a comfortable level, ensuring
there is suicient slack on the cable allowing free movement of your head
without disturbing the headset position.
In the interests of hygiene it is advisable to replace the ear cushions and
wind shield of your headset every 6 months.
Using the Quick Disconnect Lead (QD)
Your headset is equipped with a Quick Disconnect Lead (QD) allowing you
to move away from your desk (disconnecting the
2 connectors) without losing the call.
To connect the QD on your headset to the QD on the bottom lead, simply
align the two QD’s and push together. To disconnect the QD’s, simply pull
the two QD’s apart.
USER GUIDE
270°
30mm
Clothing Clip
Quick Disconnect
Microphone
Ear Cushion
Adjustable Headband
Optional
Accessory
Bottom Lead
Headset Amplier
REGISTERED ADDRESS
UK Oice: JPL Telecom Limited: Unit 1, Church Close Business Park, Todber, Sturminster Newton, Dorset, DT10 1JH, UK
USA Oice: JPL Telecom Holdings LLC: 445 W Merritt Ave, Merritt Island, FL 32953, USA
www.jpltele.com
2014/30/EU