KitchenAid KEWVP 80010 User Manual
Displayed below is the user manual for KEWVP 80010 by KitchenAid which is a product in the Cooker Hoods category. This manual has pages.
Related Manuals
Instructions for use
Important instructions for safety 4
Installation 6
Safeguarding the environment 6
Troubleshooting guide 7
After-sales Service 7
Cleaning 7
Use 8
Operation 9
Maintenance 10
These instructions are also available on the website: www.kitchenaid.eu
4
YOUR SAFETY AND THAT OF OTHERS IS
HIGHLY IMPORTANT.
This manual and the appliance itself provide
important safety warnings, to be read and observed
at all times.
This is the attention symbol, pertaining to
safety, which alerts users to potential risks to
themselves and others.
All safety warnings are preceded by the attention
symbol and the following terms:
indicates a hazardous situation which, if not
avoided, will cause serious injury.
indicates a hazardous situation which, if not
avoided, could cause serious injury.
All safety warnings specify the potential
danger/warning to which they refer and indicate
how to reduce the risk of injury, damage and
electrical shock resulting from incorrect use of the
appliance. Comply with the following instructions:
• Installation or maintenance must be carried out by
a specialized technician, in compliance with the
manufacturer’s instructions and local safety
regulations.
Do not repair or replace any part of the appliance
unless specifically requested in the user manual.
• The appliance must be disconnected from the
power supply before carrying out any installation
work.
• Earthing of the appliance is compulsory. (Not
necessary for class II hoods identified by the
symbol on the specifications label).
• The power supply cable must be long enough to
permit connecting the appliance to the mains
socket outlet.
• Do not pull the power supply cable in order to
unplug the appliance.
• The electrical components must no longer be
accessible to the user after installation.
• Do not touch the appliance with any wet part of
the body and do not operate it when barefoot.
• This appliance may be used by children older
than 8 years of age and by persons with reduced
physical, sensory or mental capacities or with
inadequate experience and knowledge only if they
are supervised or if they have been taught how to
use the appliance in conditions of safety and if
they are aware of the dangers involved. Children
must not play with the appliance. Cleaning and
maintenance must not be carried out by children,
unless they are supervised by adults.
• Do not repair or replace any part of the appliance
unless specifically indicated in the manual.
Defective parts must be replaced using genuine
parts. All other maintenance services must be
carried out by a specialized technician.
• Children must be supervised to ensure they do not
play with the appliance.
• When drilling through a wall or the ceiling, pay
attention not to damage electric connections
and/or pipes.
• The ventilation ducts must always discharge to
the outside.
• Exhaust air must not be vented through a flue
used for removal of fumes produced by
appliances burning gas or other fuels, but must
have a separate outlet. All national regulations
governing extraction of fumes must be observed.
• If the hood is used together with other appliances
operating on gas or other fuels, the negative
pressure in the room must not exceed 4 Pa (4 x
10-5 bar).
For this reason, make sure the room is adequately
ventilated.
• The Manufacturer declines any liability for
improper use or incorrect setting of the controls.
• Regular cleaning and maintenance is essential to
correct functioning and good performance of the
appliance. Frequently clean all encrustations from
dirty surfaces to prevent the accumulation of
grease. Regularly clean or replace the filters.
• Failure to observe the instructions for cleaning the
hood and replacing the filters may result in a fire.
• The fume extractor hood must never be opened
without the grease filters installed and it should
be kept under constant supervision.
• Gas appliances must be used under the extractor
hood only with pans resting.
• When using more than three gas cooking points,
the hood should be operating at power level 2 or
greater. This will eliminate heat congestion in the
appliance.
• Before touching the bulbs, first ensure that they
are cold.
• Do not use or leave the hood without its lamps
correctly installed - risk of electric shock.
• Wear work gloves for all installation and
maintenance operations.
• The product is not suitable for outdoor use.
• When the hob is in use, accessible parts of the
hood may become hot.
• Never flame cook food (flambé) under the
appliance. Using free flames might cause fire.
• Do not leave frying pans unattended when frying,
as the frying oil may catch fire.
WARNING:
DANGER:
Important instructions for safety
5
Scrapping of household appliances
• This appliance is manufactured with recyclable or
reusable materials. Dispose of it in accordance
with local waste disposal regulations. Before
disposing of it, make it unusable by cutting off its
power supply cable.
• For further information on the treatment, recovery
and recycling of household appliances, contact
your competent local authority, the collection
service for household waste or the shop where
you purchased the appliance.
KEEP THESE INSTRUCTIONS
Declaration of conformity
• This appliance has been designed, manufactured
and marketed in compliance with:
- safety objectives of the “Low Voltage” Directive
2006/95/EC (which replaces 73/23/EEC and
subsequent amendments);
- the ecodesign requirements of european
regulations n. 65/2014, and n. 66/2014 in
conformity to the european standard EN 61591
- the protection requirements of Directive “EMC”
2004/108/EC.
Electrical safety of the appliance can only be
guaranteed if it is correctly connected to an
approved earthing system.
Energy saving tips
• Switch ON the hood at minimum speed when you
start cooking and kept it running for few minutes
after cooking is finished.
• Increase the speed only in case of large amount of
smoke and vapour and use boost speed(s) only in
extreme situations.
• Replace the charcoal filter(s) when necessary to
maintain a good odour reduction efficiency.
• Clean the grease filter(s) when necessary to
maintain a good grease filter efficiency.
• Use the maximum diameter of the ducting system
indicated in this manual to optimize efficiency and
minimize noise.
6
After unpacking the appliance, check for any
damage caused during transport. In case of
problems, contact the dealer or the After-Sales
Service. To avoid any damage, it is advisable to
only remove the appliance from the polystyrene
base just before installation.
PREPARATION FOR INSTALLATION
this appliance is heavy; the hood should only be
lifted and installed by two or more people.
The minimum distance between the cooking pan
support on top of the cooker and the bottom of the
hood must not be less than 50 cm for electric
cookers and 65 cm for gas or mixed cookers.
Before installation also check the minimum
distances stated in the manual of the cooker.
If the installation instructions for the cooker specify
a greater distance between cooker and hood, this
distance must be observed.
ELECTRICAL CONNECTIONS
Make sure the power voltage specified on the
appliance rating plate is the same as the mains
voltage.
This information may be found on the inside of the
hood, under the grease filter.
Power cable replacement (type H05 VV-F 3 x 0.75
mm²) must be carried out by a qualified electrician.
Contact an authorized service centre.
If the hood is fitted with an electric plug, connect
the plug to a socket complying with current
regulations, located in an accessible place. If no
plug is fitted
(direct wiring to the mains), or if the socket is not
located in an accessible place, install a standardized
double pole power switch that will enable complete
isolation from the mains in case of category III
overvoltage conditions, in accordance with wiring
rules.
GENERAL RECOMMENDATIONS
Before use
Remove cardboard protection pieces, transparent
film and adhesive labels from accessories.
Make sure the appliance has not been damaged
during transport.
During use
Do not place weights on the appliance, as they
could damage it.
Do not expose the appliance to atmospheric agents.
WARNING:
Installation
Disposal of packing
The packing material is 100% recyclable and is
marked with the recycle symbol . The various
parts of the packing must be disposed of responsibly
and in full compliance with local authority
regulations governing waste disposal.
Disposal of the appliance
- This appliance is marked in compliance with
European Directive 2002/96/EC on Waste
Electrical and Electronic Equipment (WEEE).
- By ensuring that this appliance is disposed of
correctly, you can help prevent potentially
damaging consequences for the environment and
health.
- The symbol on the product or on the
accompanying documentation indicates that it
should not be treated as domestic waste but must
be taken to an appropriate collection centre for the
recycling of electrical and electronic equipment.
Safeguarding the environment
7
The appliance does not work:
• Check the domestic power supply and ensure the
appliance is connected to the mains properly.
• Switch the hood off and then on again to see if
the problem has been resolved.
The hood is not extracting satisfactorily:
• Check the extraction speed is set to the desired
level;
• Check the filters are clean;
• Check the air vents are not blocked;
The light does not work:
• Check to see if the lamp needs replacing;
• Check to see if the lamp has been fitted properly;
Troubleshooting guide
Before calling the After-sales Service:
1. See if you can solve the problem yourself with
the help of the “Troubleshooting guide”.
2. Switch the hood off and then on again to see if
the problem has been resolved.
If, after the above checks, the problem persists,
contact your nearest After-sales Service.
Always provide:
• a brief description of the problem;
• the type and specific model of the appliance;
• the Service number (this is the number which
follows the word SERVICE on the dataplate),
inside the appliance. The Service number is also
printed on the warranty booklet;
• your full address;
• your telephone number;
If any repairs are needed, contact an authorized
Service Centre (to ensure that only original spare
parts are used and that repairs are made correctly).
After-sales Service
- Do not use steam cleaners.
- Disconnect the appliance from the power
supply.
IMPORTANT: Do not use corrosive or abrasive
detergents. If any of these products accidentally
comes into contact with the appliance, clean it
immediately with a damp cloth.
• Clean the surfaces with a damp cloth. If very
dirty, add a few drops of washing up detergent to
the water. Dry with a dry cloth.
IMPORTANT: Do not use abrasive sponges or
metallic scrapers or scouring pads. Their use
could eventually ruin the enamelled surfaces.
• Use specific detergents to clean the appliance and
follow the manufacturer’s instructions
IMPORTANT: Clean the filters at least once a
month to remove built-up oil and grease.
WARNING:
Cleaning
8
Use
The hood is designed to be used either for
exhausting or filter version.
Ducting version
In this case the fumes are conveyed outside of the
building by means of a special pipe connected with
the connection ring located on top of the hood.
Attention! The exhausting pipe is not supplied and
must be purchased apart.
Diameter of the exhausting pipe must be equal to
that of the connection ring.
In the horizontal runs the exhausting pipe must be
slightly slanted (about 10°) and directed upwards to
vent the air easily from the room to the outside.
Attention! If the hood is supplied with active
charcoal filter, then it must be removed.
Connect the hood and discharge holes on the walls
with a diameter equivalent to the air outlet
(connection flange).
Using the tubes and discharge holes on walls with
smaller dimensions will cause a diminution of the
suction performance and a drastic increase in noise.
Any responsibility in the matter is therefore
declined.
- Use a duct of the minimum indispensible length.
- Use a duct with as few elbows as possible
(maximum elbow angle: 90°).
- Avoid drastic changes in the duct cross-section.
- Use a duct as smooth as possible inside.
- The duct must be made of certified material.
Filter version
One active charcoal filter is needed for this and can
be obtained from your usual retailer.
The filter removes the grease and smells from the
extracted air before sending it back into the room
through the upper outlet grid.
The models with no suction motor only operate in
ducting mode, and must be connected to an
external suction device (not supplied).
The connecting instructions are supplied with the
peripheral suction unit.
Installation
The minimum distance between the supporting
surface for the cooking equipment on the hob and
the lowest part of the range hood must be not less
than 30cm from electric cookers and 35cm from
gas or mixed cookers.
If the instructions for installation for the gas hob
specify a greater distance, this must be adhered to.
Electrical connection
The mains power supply must correspond to the
rating indicated on the plate situated inside the
hood. If provided with a plug connect the hood to a
socket in compliance with current regulations and
positioned in an accessible area, after installation.
If it not fitted with a plug (direct mains connection)
or if the plug is not located in an accessible area,
after installation, apply a double pole switch in
accordance with standards which assures the
complete disconnection of the mains under
conditions relating to over-current category III, in
accordance with installation instructions.
Warning! Before re-connecting the hood circuit to
the mains supply and checking the efficient
function, always check that the mains cable is
correctly assembled.
Mounting
Expansion wall plugs are provided to secure the
hood to most types of walls/ceilings. However, a
qualified technician must verify suitability of the
materials in accordance with the type of
wall/ceiling. The wall/ceiling must be strong
enough to take the weight of the hood. Do not tile,
grout or silicone this appliance to the wall. Surface
mounting only.
In the case of the presence of panels and/or walls
and/or lateral wall units check that there is
sufficient space to install the hood and that access
to the command panel is easy.
Only for some models
An aesthetic flue can be purchased as an optional
accessory.
Check with the authorized dealer whether the
model in your possession envisages this possibility.
We advise installing the hood after having
purchased the flue to check with certainty the most
suitable installation.
9
Operation
Use the high suction speed in cases of concentrated
kitchen vapours. It is recommended that the cooker
hood suction is switched on for 5 minutes prior to
cooking and to leave in operation during cooking
and for another 15 minutes approximately after
terminating cooking.
T1. Hood OFF
Press the button and the hood passes from
operation, in any suction mode, to OFF.
T2. “Silent” mode
This mode is not associated with any specific type
of cooking.
Press the button to activate the hood in silent mode.
Press button T1 or T2 and the hood passes to OFF.
T3. “Boost” mode
This mode is not associated with any specific type
of cooking.
Press the button in the case of particularly intense
fumes.
Press button T1 or T3 and the hood passes to OFF.
T4. Lighting ON/OFF
Press the button to turn the lights on or off.
T5. Cooking mode
Press the button cyclically to activate the different
suction modes.
Each mode is associated with different types of
food cooking.
This is to obtain optimum suction according to the
different needs.
A signalling LED corresponds to each suction
mode.
• “Slow cooking” mode LED L1 on
Press the button when cooking vegetables in a
pan, when heating food or drinks (milk, coffee,
tea).
• “Boiling” mode LED L2 on
Press the button when cooking sauces, broth,
boiled vegetables and soups, or when boiling
food (e.g. pasta).
• “Grilling” mode LED L3 on
Press the button when cooking food on grill or
griddle.
• “Frying” mode LED L4 on
Press the button when frying food (e.g. meat,
potatoes, vegetables).
To quit the selected suction mode press the
following buttons:
Button T1 hood in OFF
Button T2 activation of “Silent” mode
Button T3 activation of “Boost” mode
Fault alarm
In case of motor fault (stall, overheating, etc.) all
the functions of the motor will be blocked (except
for lighting) buttons T2, T3, T5 and LEDs L1, L2,
L3, L4 will flash.
Once the alarm has gone off, the hood goes back to
OFF.
Press button T1 and the hood passes to OFF.
If the fault persists, the hood remains in the alarm
state and all the functions are blocked. Contact the
technical service.
10
Maintenance
ATTENTION! Before performing any
maintenance operation, isolate the hood from the
electrical supply by switching off at the
connector and removing the connector fuse.
Or if the appliance has been connected through a
plug and socket, then the plug must be removed
from the socket.
Cleaning
The cooker hood should be cleaned regularly (at
least with the same frequency with which you carry
out maintenance of the fat filters) internally and
externally. Clean using the cloth dampened with
neutral liquid detergent. Do not use abrasive
products. DO NOT USE ALCOHOL!
WARNING: Failure to carry out the basic cleaning
recommendations of the cooker hood and
replacement of the filters may cause fire risks.
Therefore, we recommend observing these
instructions.
The manufacturer declines all responsibility for any
damage to the motor or any fire damage linked to
inappropriate maintenance or failure to observe the
above safety recommendations.
Steam screen
The steam screen must always be left closed and
opened only for maintenance (e.g. cleaning or
changing filters).
Grease filter (Fig. 8-24)
Traps cooking grease particles.
This must be cleaned once a month (or when the
filter saturation indication system – if envisaged on
the model in possession – indicates this necessity)
using non aggressive detergents, either by hand or
in the dishwasher, which must be set to a low
temperature and a short cycle.
When washed in a dishwasher, the grease filter may
discolour slightly, but this does not affect its
filtering capacity.
Open the steam screen.
To remove the grease filter, pull the spring release
handle.
Charcoal filter (filter version only) Fig. 23
It absorbs unpleasant odours caused by cooking.
The charcoal filter can be washed once every two
months using hot water and a suitable detergent, or
in a dishwasher at 65°C (if the dishwasher is used,
select the full cycle function and leave dishes out).
Eliminate excess water without damaging the filter,
then put it in the oven for 10 minutes at 100° C to
dry completely.
Replace the mattress every 3 years and when the
cloth is damaged.
•
Montage
Open the steam screen and remove the grease
filter.
Install the carbon filter on the back of the grease
filter and fix with two rods.
Attention! The rods are included in the carbon
filter packing and not on the hood.
•
To dismantle the filter act in the reverse manner.
Replacing lamps
The hood is equipped with a lighting system based
on LED technology.
The LEDs guarantee an optimum lighting, a
duration up to 10 times as long as the traditional
lamps and allow to save 90% electrical energy.
For replacement, contact the technical service.
400010785251
Printed in Italy n
04/15
GB