KitchenAid KHID3 65510 User Manual
Displayed below is the user manual for KHID3 65510 by KitchenAid which is a product in the Hobs category. This manual has pages.
Related Manuals
Instructions for use
Installation diagrams 5
Important safety instructions 7
Safeguarding the environment 10
Eco Design Declaration 10
Before use 10
Existing pots and pans 10
Recommended pot bottom widths XL 10
Installation 11
Electrical connection 11
Electrical connection 12
Cleaning 16
Troubleshooting guide 16
Noises made by the hob 16
After-Sales Service 17
Power level table 17
5
Installation diagrams
210 mm 280 mm
145 mm
6
Installation diagrams
483 mm
553 mm
30 mm
+1
0
580
650
700 mm
510 mm
52 mm
R = Min. 6,5 mm
Max. 8 mm
490 mm
560 mm
0
+2
0
+2
Min. 50 mm
Min. 10 cm
Min. 3 cm
Max. 6 cm
3
X4
1
2
Min. 5 mm
7
IMPORTANT SAFETY INSTRUCTIONS
SAFETY IS OUR PRIORITY
This manual and the appliance itself display important safety
messages, which must be read and then observed at all times.
This is the danger symbol, regarding safety, warning of potential
risks to users and others.
All safety messages are preceded by the danger symbol and the
text shown here:
DANGER Indicates a hazardous situation which, if not
avoided, will result in serious injury.
WARNING Indicates a hazardous situation which, if not
avoided, could cause serious injury.
All messages relevant to safety specify the potential risk to which they
refer and indicate how to reduce the risk of injury, damage and electric
shock due to incorrect use of the appliance.
Ensure that everyone complies with the following:
- Use protective gloves when unpacking and installing.
- The appliance must remain disconnected from the power supply
before any installation operation is carried out.
- Installation and maintenance must be carried out by a specialised
technician, in compliance with the manufacturer’s instructions and
the local safety regulations in force. Do not repair or replace any part
of the appliance unless specically stated in the user manual.
- The appliance must be earthed.
- The power cable must be long enough for connecting the appliance
(tted inside the cabinet) to the power supply.
- For installation to comply with the current safety regulations, an
omnipolar switch with minimum contact gap of 3 mm is required.
- Do not use multi-sockets or extension cords.
- Do not pull the appliance’s power cable.
These instructions are also available on our website: docs.kitchenaid.eu
8
- The electrical parts must not be accessible to the user after
installation.
- The appliance is designed solely for domestic use, for cooking food.
- No other use is permitted (e.g. heating rooms). The manufacturer
declines any liability for inappropriate use or incorrect setting of the
controls.
- The appliance and its accessible parts become hot during use. Care
should be taken to avoid touching heating elements. Very young
(0-3 years) and young children (3-8 years) must be kept away unless
continuously supervised.
- Children aged 8 years and above, and persons with reduced
physical, sensory or mental capabilities or lack of experience and
knowledge can only use this appliance if they are supervised or
have been given instructions on safe appliance use, and if they
understand the hazards involved. Children shall not play with the
appliance. Cleaning and user maintenance shall not be carried out
by children without supervision.
- Do not touch the appliance heating elements during or after use. Do
not allow the appliance to come into contact with cloths or other
ammable materials until all the components have cooled down
completely.
- Do not place ammable materials on or near the appliance.
- Overheated oils and fats catch re easily. Pay attention when
cooking food products rich in fat and oil.
- A separator panel (not supplied) must be installed in the
compartment under the appliance.
- If the surface is cracked, switch o the appliance to avoid the
possibility of electric shock. (Only for appliances with glass surface.)
- The appliance is not intended to be operated by means of an
external timer or separate remote control system.
- Unattended cooking on a hob with fat or oil can be dangerous and
may result in re. NEVER try to extinguish a re with water, but
switch o the appliance and then cover the ame with a lid or a re
blanket, for example.
Danger of re: do not store items on cooking surfaces.
9
- Do not use steam cleaners.
- Metallic objects such as knives, forks, spoons and lids should not be
placed on the hob surface since they can become hot.
- After use, switch o the hob element at its control, and do not rely
on the pan detector. (Only for appliances with glass surface.)
Disposal of household appliances
- This product is built from recyclable or reusable materials. Disposal must be carried out in accordance
with local regulations for waste disposal. Before scrapping, cut o the power supply cable.
- For further information on the treatment, recovery and recycling of household appliances, contact the
competent local authority, the domestic waste collection service or the shop where you purchased the
product.
10
Safeguarding the environment
Disposal of packing
The packing material is 100% recyclable and
marked with the recycling symbol . The various
parts of the packing must not be dispersed in the
environment, but disposed of in compliance with
local regulations.
Disposal
This appliance is marked in conformity with
European Directive 2012/19/EU on Waste Electrical
and Electronic Equipment (WEEE).
By ensuring that this appliance is correctly disposed
of, the user can help prevent potentially negative
consequences for the environment and the health
of people.
The symbol on the appliance or the
accompanying documentation indicates that this
product should not be treated as domestic waste
but must be taken to an appropriate collection
point for recycling WEEE.
Energy saving tips
For optimum results, it is advisable to:
• Use pots and pans with a base width equal to
that of the cooking zone.
• Only use at-bottomed pots and pans.
• When possible, keep pot lids on during cooking.
• Use a pressure cooker to save even more energy
and time.
• Place the pot in the middle of the cooking zone
marked on the hob.
Eco Design Declaration
This appliance meets the eco design requirements of European regulation N. 66/2014, in conformity with
European standard EN 60350-2.
Before use
IMPORTANT: The cooking zones will not switch on if pots are not the right size.
Only use pots bearing the symbol “INDUCTION SYSTEM” (gure opposite).
Place the pot on the required cooking zone before switching the hob on.
Existing pots and pans
Use a magnet to check whether the pot is suitable for the induction hob: pots and pans are unsuitable if
not magnetically detectable.
- Make sure pots have a smooth base, otherwise they could scratch the hob. Check dishes.
- Never place hot pots or pans on the surface of the hob’s control panel. This could result in damage.
-
Recommended pot bottom widths XL
XL Ø 28 cm Ø 17 cm min. 28 cm max. L Ø 21 cm Ø 15 cm min. 21 cm max.
S Ø 14.5 cm Ø 10 cm min. 14.5cm max.
IMPORTANT: Refer to the “SENSOR” section for information on the correct pan base diameters for cooking
zones with the SENSOR function. If adapter plates (not provided) are used or a pan is empty, the internal
temperature of the system will exceed the set limit and the power supply to the hob will be switched o.
This happens to protect the internal components from overloading. We recommend switching o the hob
and allowing the cooking zone to cool down to the temperature at which the indicators on the control
panel switch o.
11
Installation
After unpacking the product, check for any damage during transport.
In case of problems, contact the dealer or the After-Sales Service.
For built-in dimensions and installation instruction, see the pictures in page 5.
PREPARING THE CABINET FOR FITTING
WARNING
-Install a separator panel under the hob.
-The lower part of the product must not be accessible after installation.
-Do not t the separator panel if an undertop oven is installed.
• The distance between the underside of the appliance and the separator
panel must conform to the dimensions given in the gure.
• In order to ensure correct operation of the product, do not obstruct the
minimum required clearance between the hob and the top of the unit
(min. 5 mm).
• If an undertop oven is installed, ensure that the oven is equipped with a
cooling system.
• Do not install the hob above a dishwasher or washing-machine, so that
the electronic circuits do not come into contact with steam or moisture which could damage them.
• In the case of ush-mounted installation, call the After-Sales Service to request assembly of screws kit
4801 211 00112.
• To remove the hob, use a screwdriver (not provided) to prise o the perimeter clips on the underside
of the appliance.
Electrical connection
WARNING
-Disconnect the appliance from the power supply.
-Installation must be carried out by qualied personnel who know the current safety and
installation regulations.
-The manufacturer shall not be held liable for injury to persons or animals, or for damage to
property resulting from failure to observe the regulations provided in this chapter.
-The power cable must be long enough to allow the hob to be removed from the worktop.
-Ensure that the voltage specied on the rating plate located on the bottom of the appliance is
the same as that of the home.
min 5 mm
min 20 mm
min 5 mm
12
Electrical connection
Connection to the terminal block
For the electrical connection, use an H05RR-F or H05V2V2-F cable as specied in the table below.
Wires Number x size
230 V
230 V
230 V
230 V
230 V
230 V 230 V
230 V
230 V
230 V
230 V
380-415 V 3 N ~ 220-240 V ~ 220-240 V ~
(UK and AU)
380-415 V 2N ~ 220-240 V 3 ~
(Belgium only)
380-415 V 2N ~
(NL only)
220-240 V ~ + 3 x 4 mm2
220-240 V 3 ~ + 5 x 1.5 mm2
380-415 V 3 N ~ + 5 x 1.5 mm2
380-415 V 2 N ~ + 4 x 1.5 mm2
CBA
Important:
- Based on the wiring diagram (see gure), either keep or remove the metal jumpers between the
screws on the terminal block L1-L2 and N1-N2.
- If the cable is provided, see the connection instructions attached to the cable.
- Make sure all six screws on the terminal block are tightened after connecting the cables.
Example of jumper present (left) or removed (right). See the wiring diagram for details (the jumpers can be
between L1-L2 and between N1-N2).
Connect the yellow/green earth wire to the terminal with the symbol .
This wire must be longer than the other wires.
1. Remove the terminal block cover (A), undoing the screw and inserting the cover in the terminal block
hinge (B).
2. Insert the power cable in the cable clamp and connect the wires to the terminal block as indicated in
the connection diagram located near it.
3. Secure the power cable with the cable clamp.
4. Close the cover (C) and screw it on the terminal block with the previously removed screw.
Each time the power is connected, the hob performs an automatic check for a few seconds.
If the hob already has a power cable, follow the instructions attached to the cable. Connect the appliance
to the power supply by means of a multipole switch with minimum contact gap of 3 mm.
13
Instructions for use
Control panel description
The control panel is equipped with touch controls: to use them, just press the corresponding symbol (a
light touch is sucient).
ON/OFF
Quick access
Slider
Power management/timer/
Lock function button
Cooking zone controls and corresponding display
Switching the hob ON/OFF
To switch the hob on, press the button for approx. 2 seconds until the cooking zone displays light up.
To switch o, press the same button until the displays switch o. All the cooking zones are deactivated If
the hob has been in use, the residual heat indicator “H” remains lit until the cooking zones have cooled
down.
If no function is selected within 10 seconds of switching on, the hob switches o automatically.
Switching on and adjusting cooking zones
Power indicator display
Selected cooking zone indication
Slider operation
Increase power level
Cooking zone positioning
Decrease power level
After switching the hob on, activate the required cooking zone by pressing the corresponding circular
button and place the pot on the zone. With the Slider control it is possible to select the required power
level, from min. 0 to max. 9, or booster “P” if available.
To increase the power level, slide your nger on the slider from left to right several times; to decrease it,
slide in the opposite direction. Alternatively, the “+” and “-” quick access buttons can be used.
Deactivation of cooking zones
To switch o the cooking zone, press the corresponding button for more than 3 seconds.
The cooking zone switches o and, if still hot, the letter “H” appears on the zone display.
14
Instructions for use
Control panel lock
This function locks the controls to prevent accidental activation of the hob. To activate the control panel
lock, switch the hob on and press the Timer button for three seconds; an acoustic signal and a luminous
indicator near the padlock symbol signal activation. The control panel is locked except for the switching
o function. To deactivate the control lock, repeat the activation procedure. The luminous dot goes o and
the hob is active again.
The presence of water, liquid spilled from pots or any objects resting on the button below the symbol can
accidentally activate or deactivate the control panel Lock function.
Timer
The timer can be used to set the cooking time for a maximum of 99 minutes (1 hour and 39
minutes) for all the cooking zones.
Select the cooking zone to be used with the timer, press the timer and a beep signals the
function (see gure). The display shows “00” and the LED indication comes on. The timer value
can be decreased and increased by keeping the slider function “+” and “-” buttons pressed.
When the set time has elapsed, an acoustic signal sounds and the cooking zone switches o
automatically. To deactivate the timer, keep the Timer button pressed for at least 3 seconds.
To set the timer for another zone, repeat the above steps. The timer display always shows the timer for the
selected zone or the shortest timer.
To modify or deactivate the timer, press the cooking zone selection button for the timer in question.
CONTROL PANEL WARNINGS.
Residual heat indicator.
The hob is tted with a residual heat indicator for each cooking zone. these indicators alert the
user when cooking zones are still hot.
If the display shows “H”, the cooking zone is still hot. If the residual heat indicator of a given
cooking zone is lit, that zone can be used, for example, to keep a dish warm or to melt butter.
When the cooking zone cools down, the display goes o.
Incorrect or missing pot indicator.
If you are using a pot that is not suitable, not correctly positioned or not of the correct
dimensions for your induction hob, the message “no pot” will appear in the display (see gure
at side). If no pot is detected within 60 seconds, the hob switches o.
Fast boil function (Booster)
This function, only present on some cooking zones, makes it possible to exploit the hob’s maximum power
(to bring water to the boil very quickly, for example). To activate the function, press the “+” button until “P”
appears on the display. After 10 minutes’ use of the booster function, the appliance automatically sets the
zone to level 9.
Power management function (where available)
Thanks to the “Power management” function, the user can set the maximum power the hob can reach, as
required.
This setting is possible at any time and is maintained until the next change.
By setting the required maximum power, the hob automatically adjusts distribution in the various cooking
zones, ensuring that this limit is never exceeded; with the advantage of also being able to manage all the
zones simultaneously, but without overload problems.
4 maximum power levels are available and showed on the display: 2.5 – 4.0 – 6.0 – 7.2 kW (7.2 kW is
considered as the maximum power of the hob)
At the time of purchase, the hob is set to maximum power
After plugging the appliance into the electrical socket, in the rst 60 seconds it is possible to set the
required power level by running the following points:
Instructions for use
15
Instructions for use
Step Control panel DISPLAY
1+ Press for approximately 3 seconds
2Press the “Power management” button to
conrm the previous step
The display shows
3-/+ Press to set the chosen level amongst the
dierent options available
The light comes on together
with the lights in use for the
individual cooking zones
4Press the “Power management” button to
conrm the previous step
The display shows the set level
which ashes for approximately
2 seconds; after which the hob
emits an acoustic signal and
then turns itself o; it is now
ready for use.
In case of an error when setting the power, the symbol appears in the middle and an acoustic signal
sounds for about 5 seconds. In this case, repeat the conguration procedure from the beginning. If the
error occurs again, contact the After-Sales Service.
During normal use, if the user tries to increase the maximum available power level when reached, the level
of the zone in use ashes twice and an acoustic signal sounds.
To obtain a higher power in that zone, it is necessary to manually decrease the power level of one or more
already active cooking zones.
16
Cleaning
WARNING
-Do not use steam cleaners.
-Before cleaning, ensure that the cooking zones are switched o and that the residual heat
indicator (“H”) is not displayed.
IMPORTANT: Do not use abrasive sponges or scouring pads. Their use could eventually ruin the glass.
• After each use, clean the hob once it has cooled in order to remove any food residues.
• Sugar and foods with a high sugar content damage the hob and must be immediately removed.
• Salt, sugar and sand can scratch the glass surface.
• Use a soft cloth, absorbent kitchen paper or a specic hob cleaner (follow the manufacturer’s
instructions).
Troubleshooting guide
• Read and follow the instructions given in the section “Instructions for use”.
• Check that the electricity supply has not been shut o.
• Dry the hob thoroughly after cleaning it.
• If alphanumeric codes appear on the display when the hob is switched on, consult the following table
for instructions.
• If the hob cannot be switched o after using it, disconnect it from the power supply.
ERROR CODE DESCRIPTION POSSIBLE CAUSES ERROR ELIMINATION
C81, C82 The control panel
switches o because of
excessively high
temperatures
The internal
temperature of
electronic parts is too
high
Wait for the hob to cool
down before using it
again.
F42 or F43 The connection voltage
is wrong
The sensor detects a
discrepancy between
the appliance voltage
and that of the mains
supply
Disconnect the hob
from the mains and
check the electrical
connection
F12, F21, F25, F36,
F37, F40, F47, F56,
F58, F60
Call the After-Sales Service and specify the error code
Noises made by the hob
Induction hobs can make whistling or crackling sounds during normal operation. These sounds actually
come from the pots and pans as a result of the characteristics of their bases (for example, bases made of
several layers of material, or uneven bases). These noises vary depending on the pots and pans used and
the amount of food they contain, and are not indicative of a defect of any kind.
In addition, the induction hob is equipped with an internal cooling system to control the temperature of
electronic parts; as a result, during operation and for several minutes after the hob has been switched o,
the noise of the cooling fan will be audible. This is perfectly normal and indeed essential for proper
functioning of the appliance.
17
After-Sales Service
Before contacting the After-Sales Service
1. See whether you can solve the problem yourself with the help of the “Troubleshooting guide”.
2. Switch the appliance o and then on again it to see whether the problem has been eliminated.
If the problem persists after the above checks, contact the nearest After-Sales Service.
Always specify:
- a brief description of the fault;
- the product type and exact model;
- the Service number (the number after the word Service on the rating plate), located under the
appliance (on the metal plate).
- your full address;
- your telephone number.
If any repairs are required, contact an authorised After-Sales Service centre (to ensure use of original spare
parts and correct repairs). Spare parts are available for 10 years.
Power level table
Power level Type of cooking Used for
(indicating cooking experience and habits)
Max. power
Boost Fast heating Ideal for rapidly increasing the temperature of food to fast
boiling in the case of water or rapidly heating cooking liquids
8-9 Frying – boiling Ideal for browning, starting to cook, frying deep frozen
products, fast boiling
High power
7-8 Browning – sautéing
– boiling – grilling
Ideal for sautéing, maintaining a fast boil, cooking and grilling
(for a short period of time, 5-10 minutes)
6-7
Browning – cooking –
stewing – sautéing –
grilling
Ideal for sautéing, maintaining a light boil, cooking and grilling
(for a medium period of time, 10-20 minutes), preheating
accessories
Medium power
4-5 Cooking – stewing –
sautéing – grilling
Ideal for stewing, maintaining a gentle boil, cooking (for a long
period of time). Creaming pasta
3-4 Cooking – simmering
– thickening – reaming
Ideal for long-cooking recipes (rice, sauces, roasts, sh) with
liquids (e.g. water, wines, broth, milk), creaming pasta
2-3 Ideal for long-cooking recipes (less than a litre in volume: rice,
sauces, roasts, sh) with liquids (e.g. water, wine, broth, milk)
Low power
1-2 Melting – defrosting –
keeping food warm –
creaming
Ideal for softening butter, gently melting chocolate, defrosting
small items and keeping just-cooked food warm (e.g. sauces,
soups, minestrone)
1
Ideal for keeping just-cooked food warm, for creaming risottos
and for keeping serving dishes warm (with accessory suitable
for induction)
OFF Zero
power Support surface Hob in stand-by or OFF mode (possible end-of-cooking
residual heat, indicated by an “H”)
NOTE:
When making quick-cook foods that require perfect heat distribution (e.g. pancakes) on the 28 cm double
cooking zone (where present), use pans no greater than 24 cm in diameter. For delicate cooking (for
example, melting chocolate or butter) use the smaller diameter single zones.
GB
Printed in Italy
05/16
400010839674
WHIRLPOOL EUROPE s.r.l. Socio Unico
Viale G. Borghi, 27
21025 COMERIO (Varese) ITALY
Phone +39 0332 759111 – Fax +39 0332 759268
www.whirlpool.eu