Table of Contents
- Contents
- Legal and Safety Information
- Notice
- Regarding Tradenames
- Compliance and Conformity
- Safety Instructions Regarding the Disconnection of Power
- Energy Saving Control Function
- Duplex Printing
- Resource Saving - Paper
- Environmental benefits of "Power Management"
- Energy Star (ENERGY STAR®)
- Legal Restriction on Copying/Scanning
- Safety Conventions in This Guide
- Environment
- Cautions when Handling Consumables
- About the Operation Guide
- Conventions in This Guide
- 1 Machine Parts
- 2 Preparation
- 3 Copying
- 4 Printing
- 5 Scanning
- 6 Maintenance
- 7 Troubleshooting
- 8 Appendix
- Index
KYOCERA FS-1220MFP User Manual
Displayed below is the user manual for FS-1220MFP by KYOCERA which is a product in the Multifunctionals category. This manual has pages.
Related Manuals
FS-1020MFP/FS-1220MFP
oPeratioN guide
This Operation Guide is for models FS-1020MFP and FS-1220MFP.
This Operation Guide is intended to help you operate the machine correctly, perform routine maintenance and take a
simple troubleshooting action as necessary, so that you can always use the machine in good condition.
We recommend the use of our own brand supplies. We will not be liable for any damage caused by the use of third party
supplies in this machine.
A label shown in the illustration assures that the supplies are our own brand.
Included Guides
The following guides are supplied with the machine. Refer to them as necessary.
Product Library disc
Quick Installation Guide Describes the procedures for installation of the machine.
Safety Guide Provides safety and cautionary information for the installation and use of
the machine. Be sure to read this guide before using the machine.
Safety Guide
(FS-1020MFP/FS-1025MFP/FS-1120MFP/
FS-1125MFP/FS-1220MFP/FS-1320MFP/
FS-1325MFP)
Describes the machine installation space, cautionary space, and other
information. Be sure to read this guide before using the machine.
Operation Guide (This Guide) Describes how to load paper, basic copy, print and scan operations, and
troubleshooting.
KYOCERA Client Tool User Guide Describes how to use KYOCERA Client Tool. KYOCERA Client Tool is a
software program that is installed on your computer to enable you to
configure machine settings.
Printer Driver User Guide Describes how to install the printer driver and use printer functionality.
KYOCERA Net Viewer User Guide Describes how to monitor the network printing system with KYOCERA
Net Viewer.
i
Contents
1 Machine Parts ................................................................................................................................................1-1
Front Machine Components .........................................................................................................................1-2
Rear Machine Components ..........................................................................................................................1-3
Operation Panel .............................................................................................................................................1-4
2 Preparation .....................................................................................................................................................2-1
Connections ...................................................................................................................................................2-2
Loading Paper ................................................................................................................................................2-4
Loading Originals ........................................................................................................................................2-16
Installing and Uninstalling Drivers and Utilities .......................................................................................2-17
Machine Settings .........................................................................................................................................2-22
Configuration ...............................................................................................................................................2-36
Printing the Status Page .............................................................................................................................2-42
3 Copying ..........................................................................................................................................................3-1
Basic Operation .............................................................................................................................................3-2
Manual Duplex ...............................................................................................................................................3-3
Using Programs .............................................................................................................................................3-5
Copying Functions ........................................................................................................................................3-5
ID Card Copy ..................................................................................................................................................3-6
4 Printing ...........................................................................................................................................................4-1
Printing from Application Software .............................................................................................................4-2
About GX Driver .............................................................................................................................................4-2
Manual Duplex ...............................................................................................................................................4-3
Print Box .........................................................................................................................................................4-5
Changing the Default Printer Driver Settings (Windows 7 for example) ..................................................4-6
5 Scanning ........................................................................................................................................................5-1
Push Scan ......................................................................................................................................................5-2
Using Programs .............................................................................................................................................5-3
Quick Scan (Scan to PDF/Scan to Email/Scan to Folder) ..........................................................................5-4
Scanning using TWAIN/WIA .........................................................................................................................5-5
6 Maintenance ...................................................................................................................................................6-1
General Information ......................................................................................................................................6-2
Toner Container Replacement .....................................................................................................................6-2
Maintenance Kit Replacement ......................................................................................................................6-5
Cleaning the Machine ....................................................................................................................................6-5
Maintenance Menu ........................................................................................................................................6-7
Prolonged Non-Use and Moving of the Machine ........................................................................................6-8
7 Troubleshooting ............................................................................................................................................7-1
Solving Malfunctions ....................................................................................................................................7-2
Error Messages ..............................................................................................................................................7-7
Clearing Paper Jams .....................................................................................................................................7-9
8 Appendix ........................................................................................................................................................8-1
Specifications ................................................................................................................................................8-2
Index .............................................................................................................................................................. Index-1
ii
iii
Legal and Safety Information
Notice
The information in this guide is subject to change without notification. Additional pages may be inserted in future editions.
The user is asked to excuse any technical inaccuracies or typographical errors in the present edition.
No responsibility is assumed if accidents occur while the user is following the instructions in this guide. No responsibility is
assumed for defects in the machine's firmware (contents of its read-only memory).
This guide, and any copyrightable subject matter sold or provided with or in connection with the sale of the machine, are
protected by copyright. All rights are reserved. Copying or other reproduction of all or part of this guide, or any
copyrightable subject matter without the prior written consent of KYOCERA Document Solutions Inc. is prohibited. Any
copies made of all or part of this guide, or any copyrightable subject must contain the same copyright notice as the material
from which the copying is done.
Regarding Tradenames
Adobe Acrobat, and Flash are registered trademarks of Adobe Systems Incorporated.
Macintosh and Mac OS are trademarks of Apple Inc., registered in the U.S. and other countries.
Microsoft, MS-DOS, and Windows are registered trademarks of Microsoft Corporation in the U.S.A. and/or other countries.
ENERGY STAR is a U.S. registered mark.
All other brand and product names are registered trademarks or trademarks of their respective companies.
CAUTION NO LIABILITY IS ASSUMED FOR ANY DAMAGE CAUSED BY IMPROPER INSTALLATION.
iv
Compliance and Conformity
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
• The use of a non-shielded interface cable with the referenced device is prohibited.
CAUTION — The changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
This device complies with Part 15 of FCC Rules.
Operation is subject to the following two conditions; (1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause undesired operation of the device.
* The above warning is valid only in the United States of America.
Interface connectors
IMPORTANT Be sure to power off the machine before connecting or disconnecting an interface cable. For protection
against static electricity discharge to the machine's internal electronics through the interface connector(s), cover any
interface connector that is not in use with the protective cap supplied.
CDRH Regulations
The Center for Devices and Radiological Health (CDRH) of the U.S. Food and Drug Administration implemented
regulations for laser products on August 2, 1976. These regulations apply to laser products manufactured after August 1,
1976. Compliance is mandatory for products marketed in the United States. A label indicating compliance with the CDRH
regulations must be attached to laser products marketed in the United States.
Canadian Department of Communications Compliance Statement
This Class B digital apparatus complies with Canadian ICES-003.
Avis de conformité aux normes du ministère des Communications du Canada
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Note Use shielded interface cables.
v
Safety Instructions Regarding the Disconnection of Power
Caution: The power plug is the main isolation device! Other switches on the equipment are only functional switches and
are not suitable for isolating the equipment from the power source.
VORSICHT: Der Netzstecker ist die Hauptisoliervorrichtung! Die anderen Schalter auf dem Gerät sind nur
Funktionsschalter und können nicht verwendet werden, um den Stromfluß im Gerät zu unterbrechen.
Energy Saving Control Function
To reduce energy consumption while in a waiting state, the device comes equipped with an energy saving control function
for switching to Sleep Mode as well as Power Off Mode where power consumption is automatically reduced to a
minimum after a certain amount of time elapses since the device was last used.
Sleep Mode
The device automatically enters Sleep Mode when approximately 1 minute has passed since the device was last used.
The amount of time of no activity that must pass before Sleep Mode is activated may be lengthened by changing the Auto
sleep setting. For details, refer to Device Defaults Tab on page 2-38.
Power Off Mode
The device automatically turns its power off when 1 hour has passed since the device was last used. The amount of time
of no activity that must pass before Power Off Mode is activated may be lengthened by changing the Power Off Timer
setting. For details, refer to Device Defaults Tab on page 2-38.
In case of not using the machine for an extended period of time
CAUTION Remove paper from the cassettes and seal it in the paper storage bag to protect it from humidity.
Duplex Printing
This machine includes duplex printing as a standard function. For example, by printing two single-sided originals onto a
single sheet of paper as a duplex printing, it is possible to lower the amount of paper used.
Printing in duplex mode reduces paper consumption and contributes to the conservation of forest resources. Duplex mode
also reduces the amount of paper that must be purchased, and thereby reduces cost. It is recommended that machines
capable of duplex printing be set to use duplex mode by default.
Resource Saving - Paper
For the preservation and sustainable use of forest resources, it is recommended that recycled as well as virgin paper
certified under environmental stewardship initiatives or carrying recognised ecolabels, which meet EN 12281:2002*1 or an
equivalent quality standard, be used.
This machine also supports printing on 64 g/m² paper. Using such paper containing less raw materials can lead to further
saving of forest resources.
*1: EN12281:2002 "Printing and business paper - Requirements for copy paper for dry toner imaging processes"
Your sales or service representative can provide information about recommended paper types.
CAUTION If this machine will be left unused for an extended period (e.g. overnight), turn it off at the power
switch. If the machine will not be used for an even longer period of time (e.g. vacation), remove the power
plug from the outlet as a safety precaution.
vi
Environmental benefits of "Power Management"
To reduce power consumption when idle, this machine is equipped with a power management function that automatically
activates energy-saving mode when the machine is idle for a certain period of time. Although it takes the machine a slight
amount of time to return to READY mode when in energy-saving mode, a significant reduction in energy consumption is
possible.
It is recommended that the machine be used with the activation time for energy-saving mode set to the default setting.
Energy Star (ENERGY STAR®)
We have determined as a company participating in ENERGY STAR® that this product has earned the
ENERGY STAR®.
ENERGY STAR® is a voluntary energy efficiency program with the goal of developing and promoting the
use of products with high energy efficiency in order to help prevent global warming. By purchasing
ENERGY STAR® qualified products, customers can help reduce emissions of greenhouse gases during
product use and cut energy-related costs.
Legal Restriction on Copying/Scanning
It may be prohibited to copy/scan copyrighted material without permission of the copyright owner.
Copying/Scanning the following items is prohibited and may be penalized by law. It may not be limited to these items. Do
not knowingly copy/scan the items that are not to be copied/scanned.
•Paper money
•Bank note
•Securities
•Stamp
•Passport
•Certificate
Local laws and regulations may prohibit or restrict copying/scanning of other items not mentioned above.
vii
Safety Conventions in This Guide
The sections of this guide and parts of the machine marked with symbols are safety warnings meant to protect the user,
other individuals and surrounding objects, and ensure correct and safe usage of the machine. The symbols and their
meanings are indicated below.
The following symbols indicate that the related section includes safety warnings. Specific points of attention are indicated
inside the symbol.
The following symbols indicate that the related section includes information on prohibited actions. Specifics of the
prohibited action are indicated inside the symbol.
The following symbols indicate that the related section includes information on actions which must be performed. Specifics
of the required action are indicated inside the symbol.
Please contact your service representative to order a replacement if the safety warnings in this Operation Guide are
illegible or if the guide itself is missing. (fee required)
WARNING: Indicates that serious injury or even death may result from insufficient attention to or incorrect
compliance with the related points.
CAUTION: Indicates that personal injury or mechanical damage may result from insufficient attention to or
incorrect compliance with the related points.
.... [General warning]
.... [Warning of high temperature]
.... [Warning of prohibited action]
.... [Disassembly prohibited]
.... [Alert of required action]
.... [Remove the power plug from the outlet]
.... [Always connect the machine to an outlet with a ground connection]
Note An original which resembles a bank note closely may not be copied properly in some rare cases because this
machine is equipped with a counterfeiting prevention function.
viii
Environment
The service environmental conditions are as follows:
•Temperature: 50 to 90.5 °F (10 to 32.5 °C)
•Humidity: 15 to 80 %
However, adverse environmental conditions may affect the image quality. Avoid the following locations when selecting a
site for the machine.
•Avoid locations near a window or with exposure to direct sunlight.
•Avoid locations with vibrations.
•Avoid locations with drastic temperature fluctuations.
•Avoid locations with direct exposure to hot or cold air.
•Avoid poorly ventilated locations.
If the floor is delicate against casters, when this machine is moved after installation, the floor material may be damaged.
During printing, some ozone is released, but the amount does not cause any ill effect to one’s health. If, however, the
machine is used over a long period of time in a poorly ventilated room or when printing an extremely large number of
copies, the smell may become unpleasant. To maintain the appropriate environment for print work, it is suggested that the
room be properly ventilated.
Cautions when Handling Consumables
Do not attempt to incinerate parts which contain toner. Dangerous sparks may cause burns.
Keep parts which contain toner out of the reach of children.
If toner happens to spill from parts which contain toner, avoid inhalation and ingestion, as well as contact with your
eyes and skin.
•If you do happen to inhale toner, move to a place with fresh air and gargle thoroughly with a large amount of
water. If coughing develops, contact a physician.
•If you do happen to ingest toner, rinse your mouth out with water and drink 1 or 2 cups of water to dilute the contents of
your stomach. If necessary, contact a physician.
•If you do happen to get toner in your eyes, flush them thoroughly with water. If there is any remaining tenderness,
contact a physician.
•If toner does happen to get on your skin, wash with soap and water.
Do not attempt to force open or destroy parts which contain toner.
Other precautions
After use, always dispose of the Toner Container in accordance with Federal, State and Local rules and regulations.
Store all consumables in a cool, dark location.
If the machine will not be used for an extended period of time, remove the paper from the cassette, return it to its original
package and reseal it.
ix
About the Operation Guide
This Operation Guide contains the following chapters:
1 Machine Parts
This chapter lists the names of different machine parts.
2Preparation
This chapter explains how to start up the machine, load paper and originals, and use the application software included in
the Product Library disc.
3Copying
This chapter explains the functions you can use when copying.
4Printing
This chapter explains the printing procedure from an application software.
5 Scanning
This chapter explains the functions you can use when scanning originals.
6 Maintenance
This chapter explains how to replace the toner container and how to care for your machine.
7 Troubleshooting
This chapter explains how to handle machine problems that may occur, such as paper jams.
8 Appendix
This chapter lists the machine specifications.
Conventions in This Guide
This manual uses the following conventions.
Convention Description Example
Italic Typeface Used to emphasize a key word, phrase
or reference to additional information.
Refer to Connections on page 2-2.
Bold Used to denote buttons on the
software.
To start printing, click OK.
Bracket Bold Used to denote operation panel keys. Press [Start] to start copying.
Courier Indicates characters entered in the
display on the operation panel.
1- appears in the display on the operation panel.
Note Used to provide additional or useful
information about a function or feature. Note Do not remove the toner container from the
carton until you are ready to install it in the machine.
Important Used to provide important information. IMPORTANT Take care not to touch the drum and
transfer roller (black) during cleaning.
Caution Used to suggest mechanical damage
as a result of an action.
CAUTION When removing a paper jam, pull the paper
gently so as not to tear it. Torn pieces of paper are difficult
to remove and may be easily overlooked, deterring the
paper jam recovery.
Warning Used to alert users to the possibility of
personal injury.
WARNING If you are shipping the machine, remove and
pack the developer unit and drum unit in a plastic bag and
ship them separately from the machine.
x
1-1
1 Machine Parts
This chapter explains the following topics:
Front Machine Components.................................................................................................................................. 1-2
Rear Machine Components................................................................................................................................... 1-3
Operation Panel...................................................................................................................................................... 1-4
1-2
Machine Parts
Front Machine Components
1Original Cover
2Original Size Indicator Plates
3Platen
4Inner Tray
5Paper Stopper
6Front Cover
7Cassette Cover
8Cassette
9Operation Panel
10 Power Switch
2
5
7
9
10
8
1
3
4
6
1-3
Machine Parts
Rear Machine Components
11 Rear Cover
12 Power Cord Connector
13 USB Interface Connector
13 11
12
1-4
Machine Parts
Operation Panel
Mode Select key •Set the mode to Copies,
Density, or Program.
•Press and hold for 5 seconds to
print the status page. Refer to
Printing the Status Page on
page 2-42.
Copies indicator Lights up when Copies is selected.
Enter the number of copies.
Density indicator Lights up when Density is selected.
Adjust the copy density.
Program indicator Lights up when Program is
selected. Select the program
number.
[Stop/Reset] key •Cancels the printing job in progress.
•Returns settings to their default states.
•Hold down two seconds to pause printing. Hold down two seconds again to
resume printing.
[Start] key Starts copying and scanning operations.
Processing Indicator (Green) Flashes when the machine is processing data.
Attention Indicator (Amber) Lights or flashes when an error occurs.
[Quiet Mode] key Turns on Quiet Mode.
Quiet Mode
If you prefer quiet operation, press [Quiet Mode] to turn on Quiet Mode. When Quiet
Mode is on, the print speed is slower.
Display •Displays numerical values and
settings such as the number of copies,
and error codes.
•When the machine is in sleep mode,
-- is displayed.
[] key / [] key Increments/decrements numbers in the
display.
[ID Card Copy] key Displays the ID Card Copy
screen.
[Copy] key Displays the Copy screen.
[Scan] key Displays the Scan screen.
[Print Box] key Displays the Print Box screen.
2-1
2 Preparation
This chapter explains the following topics:
Connections ........................................................................................................................................................... 2-2
Loading Paper ........................................................................................................................................................ 2-4
Loading Originals................................................................................................................................................. 2-16
Installing and Uninstalling Drivers and Utilities................................................................................................ 2-17
Machine Settings.................................................................................................................................................. 2-22
Configuration........................................................................................................................................................ 2-36
Printing the Status Page...................................................................................................................................... 2-42
2-2
Preparation
Connections
This section explains how to start up the machine.
Connecting the USB Cable
Follow the steps as below for connecting the USB cable.
1Connect the USB cable to the machine’s USB interface connector.
2Connect the other end of the USB cable to the computer's USB interface connector.
Connecting the Power Cord
Install the machine close to an AC wall outlet. If an extension cord is used, the total length of the power cord plus extension
should be 5 meters (16 feet) or less.
1Connect the power cord to the power cord connector at the rear of the machine.
2Connect the other end of the power cord to a power outlet.
Note Use a USB cable with a rectangular Type A plug and a square Type B plug.
The USB cable should be shielded and no longer than 5 meters (16 feet) long.
Note Only use the power cord supplied with the machine.
2-3
Preparation
3Press the power switch to On. The machine begins to warm up.
Starter Toner Container
The toner container packed with the new machine is a starter toner container. The starter toner container lasts an average
of 700 pages.
IMPORTANT If you install the toner container and switch on the power, a screen with
two bars ( ) rotating is shown on the display on the operation panel. When the
machine is first switched on after toner installation, there will be a delay of
approximately 7 minutes before the machine gets ready to use. Once 01 appears in the
display on the operation panel, machine installation is complete.
2-4
Preparation
Loading Paper
General Guidelines
The machine is designed to print on standard copier paper, but it can also accept a variety of other types of paper within
the limits specified below.
Selection of the right paper is important. Using the wrong paper can result in paper jams, curling, poor print quality, and
paper waste, and in extreme cases can damage the machine. The guidelines given below will increase the productivity of
your office by ensuring efficient, trouble-free printing and reducing wear and tear on the machine.
Paper Availability
Most types of paper are compatible with a variety of machines. Paper intended for xerographic copiers can also be used
with the machine.
There are three general grades of paper: economy, standard, and premium. The most significant difference between
grades is the ease with which they pass through the machine. This is affected by the smoothness, size, and moisture
content of the paper, and the way in which the paper is cut. The higher the grade of paper you use, the less risk there will
be of paper jams and other problems, and the higher the level of quality your printed output will reflect.
Differences between paper from different suppliers can also affect the machine's performance. A high-quality machine
cannot produce high-quality results when the wrong paper is used. Low-priced paper is not economical in the long run if it
causes printing problems.
Paper in each grade is available in a range of basis weights (defined later). The traditional standard weights are 60 to
120 g/m² (16 to 31.9b).
Paper Specifications
The following table summarizes the basic paper specifications. Details are given on the following pages:
Note The manufacturer assumes no liability for problems that occur when paper not satisfying these requirements
is used.
Item Specifications
Weight 60 to 220 g/m² (16 to 58.5 lb/ream)
Thickness 0.086 to 0.110 mm (3.4 to 4.3 mils)
Dimensional Accuracy ±0.7 mm (±0.0276 inches)
Squareness of Corners 90 ±0.2°
Moisture Content 4 to 6%
Pulp Content 80% or more
2-5
Preparation
Minimum and Maximum Paper Sizes
The minimum and maximum paper sizes are as follows.
Selecting the Right Paper
This section describes the guidelines for selecting paper.
Condition
Avoid using paper that is bent at the edges, curled, dirty, torn, embossed, or contaminated with lint, clay, or paper shreds.
Use of paper in these conditions can lead to illegible printing and paper jams, and can shorten the life of the machine. In
particular, avoid using paper with a surface coating or other surface treatment. Paper should have as smooth and even a
surface as possible.
Composition
Do not use paper that has been coated or surface-treated and contains plastic or carbon. The heat of fusing can cause
such paper to give off harmful fumes.
Bond paper should contain at least 80% pulp. Not more than 20% of the total paper content should consist of cotton or
other fibers.
Paper Sizes
Cassette is available for the paper sizes shown below. The dimensional tolerances are ±0.7 mm for the length and width.
The angle at the corners must be 90° ±0.2°.
•A4 (210 × 297 mm)
•A5 (148 × 210 mm)
•A6 (105 × 148 mm)
•Folio (210 × 330 mm)
•JIS B5 (182 × 257 mm)
•ISO B5 (176 × 250 mm)
•Letter (8-1/2 × 11 inches)
•Legal (8-1/2 × 14 inches)
•Statement (5-1/2 × 8-1/2 inches)
•Executive (7-1/4 × 10-1/2 inches)
70 mm
(2-3/4 inches)
148 mm (5-13/16 inches)
Minimum
Paper Size
Maximum
Paper Size
216 mm (8-1/2 inches)
356 mm (14 inches)
2-6
Preparation
•Envelope Monarch (3-7/8 × 7-1/2 inches)
•Envelope #10 (4-1/8 × 9-1/2 inches)
•Envelope #9 (3-7/8 × 8-7/8 inches)
•Envelope #6-3/4 (3-5/8 × 6-1/2 inches)
•Envelope C5 (162 × 229 mm)
•Envelope DL (110 × 220 mm)
•Oficio II (216 × 340 mm, 8-1/2 × 13 inches)
•216 × 340 mm
•16 K (197 × 273 mm)
•Custom*
70 × 148 to 216 × 356 mm, 2-3/4 × 5-13/16 to 8-1/2 × 14 inches
* If the length of custom paper is larger than 297 mm (11-11/16 inches), the machine can be substituted A4, Folio,
Legal, and Oficio II as the standard paper size.
Smoothness
The paper should have a smooth, uncoated surface. Paper with a rough or sandy surface can cause blank spaces in the
printed output. Paper that is too smooth can cause multiple feeding and fogging problems. (Fogging is a gray background
effect.)
Basis weight
Basis weight is the weight of paper expressed in grams per square meter (g/m²). Paper that is too heavy or too light may
cause feed errors or paper jams as well as premature wear of the product. Uneven weight of paper, namely uneven paper
thickness may cause multiple-sheet feeding or print quality problems such as blurring because of poor toner fusing.
The recommended basis weight is between 60 and 220 g/m² (16 to 58.5 lib/ream).
Paper Weight Equivalence Table
The paper weight is listed in pounds (lb) and metric grams per square meter (g/m²). The shaded part indicates the
standard weight.
Thickness
The paper used with the machine should be neither extremely thick nor extremely thin. If you are having problems with
paper jams, multiple feeds, and faint printing, the paper you are using may be too thin. If you are having problems with
paper jams and blurred printing the paper may be too thick. The correct thickness is 0.086 to 0.110 mm (3.4 to 4.3 mils).
Moisture Content
Moisture content is defined as the percent ratio of moisture to the dry mass of the paper. Moisture can affect the paper’s
appearance, feed ability, curl, electrostatic properties, and toner fusing characteristics.
Europe Metric Weight
(g/m²) U. S. Bond Weight (lb) Europe Metric Weight
(g/m²) U. S. Bond Weight (lb)
60 16 128 34
64 17 135 36
75 20 148 39
80 21 157 42
81 22 163 43
90 24 176 47
100 27 199 53
105 28 220 58.5
120 32
2-7
Preparation
The moisture content of the paper varies with the relative humidity in the room. When the relative humidity is high and the
paper absorbs moisture, the paper edges expand, becoming wavy in appearance. When the relative humidity is low and
the paper loses moisture, the edges shrink and tighten, and print contrast may suffer.
Wavy or tight edges can cause jams and alignment anomalies. The moisture content of the paper should be 4 to 6%.
To ensure correct moisture content, it is important to store the paper in a controlled environment. Some tips on moisture
control are:
•Store paper in a cool, dry location.
•Keep the paper in its wrapping as long as possible. Re-wrap paper that is not in use.
•Store paper in its original carton. Place a pallet etc. under the carton to separate it from the floor.
•After removing paper from storage, let it stand in the same room as the machine for 48 hours before use.
•Avoid leaving paper where it is exposed to heat, sunlight, or damp.
Other Paper Properties
Porosity: Indicates the density of paper fiber.
Stiffness: Limp paper may buckle in the machine, resulting in paper jams.
Curl: Most paper naturally tends to curl one way if left unpacked. When paper passes through the fixing unit, it curls
upward a little. To produce flat printouts, load the paper so that the upward pressure from the machine can correct their
curling.
Electrostatic discharge: During the printing process the paper is electrostatically charged to attract the toner. The paper
must be able to release this charge so that printed sheets do not cling together in the Output Tray.
Whiteness: The contrast of the printed page depends on the whiteness of the paper. Whiter paper provides a sharper,
brighter appearance.
Quality control: Uneven sheet size, corners that are not square, ragged edges, welded (uncut) sheets, and crushed
edges and corners can cause the machine to malfunction in various ways. A quality paper supplier should take
considerable care to ensure that these problems do not occur.
Packaging: Paper should be packed in a sturdy carton to protect it from damage during transport. Quality paper obtained
from a reputable supplier is usually correctly packaged.
Specially treated paper: We do not recommend printing onto the following types of paper, even if it conforms to the basic
specifications. When you use these kinds of paper, purchase a small amount first as a sample to test.
•Glossy paper
•Watermarked paper
•Paper with an uneven surface
•Perforated paper
2-8
Preparation
Special Paper
The following types of special paper can be used:
•Preprinted paper
•Labels*
•Bond paper
•Recycled paper
•Thin paper* (60 to 64 g/m²)
•Rough paper
•Letterhead
•Colored paper
•Prepunched paper
•Envelopes*
•Cardstocks (Postcards)*
•Thick paper (90 to 220 g/m²)
•High-quality paper
* Only one sheet can be loaded at a time in the cassette.
Use paper that is sold specifically for use with copiers or printers (heat-fusing type).
Since the composition and quality of special paper vary considerably, special paper is more likely than white bond paper to
give trouble during printing. No liability will be assumed if moisture and so forth given off during printing on special paper
causes harm to the machine or operator.
Labels
One label sheet can be loaded at a time.
The basic rule for printing on adhesive labels is that the adhesive must never come into contact with any part of the
machine. Adhesive paper sticking to the drum or rollers will damage the machine.
Label paper has a structure comprising of three layers, as shown in the diagram. The top sheet is printed on. The adhesive
layer consists of pressure-sensitive adhesives. The carrier sheet (also called the linear or backing sheet) holds the labels
until used. Due to the complexity of its composition, adhesive-backed label paper is particularly likely to give printing
problems.
Adhesive label paper must be entirely covered by its top sheet, with no spaces between the individual labels. Labels with
spaces in between are liable to peel off, causing serious paper jam problems.
Note Before purchasing any type of special paper, test a sample on the machine and check that printing quality is
satisfactory.
Top sheet (white bond paper)
Adhesive
Carrier sheet
2-9
Preparation
Some label paper is manufactured with an extra margin of top sheet around the edge. Do not remove the extra top sheet
from the carrier sheet until after printing is finished.
The table below lists the specifications for adhesive label paper.
Postcards
One postcard can be loaded at a time. Make sure the postcards you are going to set are not curled. Feeding curled
postcards may cause paper jams.
Some postcards have rough edges on the back (those are created when the paper is cut). In this case, put the postcard on
a flat place and rub the edges with, for example, a ruler to smooth them.
Envelopes
One envelope can be loaded at a time. Envelopes should be fed in the face-up position, right edge first.
Since the composition of an envelope is more complex than that of ordinary paper, it is not always possible to ensure
consistent printing quality over the entire envelope surface.
Normally, envelopes have a diagonal grain direction. This direction can easily cause wrinkles and creases when envelopes
pass through the machine. Before purchasing envelopes, make a test print to check whether the machine accepts the
envelope.
•Do not use envelopes that have an encapsulated liquid adhesive.
•Avoid a long printing session for envelopes only. Extended envelope printing can cause premature machine wear.
Item Specification
Weight of top sheet 44 to 74 g/m² (12 to 20 lb/ream)
Composite weight 104 to 151 g/m² (28 to 40 lb/ream)
Thickness of top sheet 0.086 to 0.107 mm (3.9 to 4.2 mils)
Composite thickness 0.115 to 0.145 mm (4.5 to 5.7 mils)
Moisture content 4 to 6% (composite)
Top sheet
UnacceptableAcceptable
Carrier sheet
2-10
Preparation
Thick Paper
If an excessive amount of thick paper is loaded in the cassette, it may not be fed. In that case, reduce the number of
sheets to be loaded.
Fan the stack of paper and align the edges before loading them in the paper source. Some types of paper have rough
edges on the back (those are created when the paper is cut). In this case, put the paper on a flat place and rub the edges
once or twice with, for example, a ruler to smooth them. Feeding rough edged paper may cause paper jams.
Colored Paper
Colored paper should satisfy the same conditions as white bond paper. Refer to Paper Specifications on page 2-4. In
addition, the pigments used in the paper must be able to withstand the heat of fusing during the printing process (up to
200°C or 392°F).
Preprinted Paper
Preprinted paper should satisfy the same conditions as white bond paper. Refer to Paper Specifications on page 2-4. The
preprinted ink must be able to withstand the heat of fusing during the printing process, and must not be affected by silicone
oil.
Do not use paper with any kind of surface treatment, such as the type of paper commonly used for calendars.
Recycled Paper
Select recycled paper that meets the same specifications as the white bond paper except for whiteness. Refer to Paper
Specifications on page 2-4.
Note If paper is not fed even after its rough edges have been removed, warp the paper at the leading edge upward
for a few millimeters as shown in the figure, and then load the paper.
Note Before purchasing recycled paper, test a sample on the machine and check that the printing quality is
satisfactory.
Burrs
Burrs
2-11
Preparation
Paper Type
The machine is capable of printing under the optimum setting for the type of paper being used.
Not only can preset paper types be selected, but it is also possible for you to define and select customized paper types.
Paper type can be changed using the printer driver and KYOCERA Client Tool. The following types of paper can be used.
Preparing the Paper
After removing paper from the packaging, fan through the sheets to separate them prior to loading.
If using paper that has been folded or is curled, straighten it prior to loading. Failure to do so may result in a paper jam.
Paper Type Paper Weight Displayed in
KYOCERA Client Tool Paper Type Paper Weight Displayed in
KYOCERA Client Tool
Plain Normal 2 Color Normal 2
Preprinted Normal 2 Prepunched Normal 2
Labels*
* One sheet must be loaded at a time.
Heavy 1 Envelope* Heavy 2
Bond Heavy 1 Cardstock* Heavy 2
Recycled Normal 2 Thick Heavy 2
Vellum* Light High quality Normal 2
Rough Heavy 1 Custom 1 (to 8)**
** This is a paper type defined and registered by the user. Up to eight types of user settings may be defined. For
more information, refer to KYOCERA Client Tool User Guide.
Normal 2
Letterhead Normal 2
IMPORTANT Ensure paper is not stapled and clips are removed.
You should not use inkjet printer paper or any paper with a special surface coating. (Such papers may cause paper
jams or other faults.)
2-12
Preparation
Loading Paper into Cassette
250 sheets of A4 or Letter paper (80 g/m²) may be loaded into the cassette.
1Open the cassette cover.
2Adjust the position of the width guides located on the left and right sides of the cassette.
Note When using paper that is larger than A4/Letter, remove the cassette cover.
Gently press on both the left and right sides of the cassette cover and pull.
If necessary, open the paper stopper shown in the figure.
Note Paper sizes are marked on the cassette.
1 2
2-13
Preparation
3Adjust the paper length guide to the paper size required.
Note When using paper larger than A4/Letter, pull out the paper length guide.
When using A6 paper, attach the stopper.
Move the stopper to the A6 position.
2-14
Preparation
4Load the paper all the way in the cassette until the paper touches the far inner side. Ensure
the side to be printed is facing up and the paper is not folded, curled, or damaged.
IMPORTANT Adjust so that there is no gap between the paper length guide and the
paper.
Note Load an amount of paper that fits under (does not contact) the tabs on the width
guides.
When using A6 paper, load the paper as shown in the illustration.
When loading an envelope, load as shown in the illustration.
Load envelope with the print side facing up.
Correct Incorrect
Close the flap.
2-15
Preparation
5Close the cassette cover.
6Specify the paper size and type for the cassette using KYOCERA Client Tool. For more
information, refer to Configuration on page 2-36.
When you attach the cassette cover
Attach the cassette cover as shown.
Note When storing the cassette, or when using paper larger than A4/Letter, remove
the cassette cover.
Note Set the same paper size to the paper size that is set on the machine.
2-16
Preparation
Loading Originals
You may place books or magazines on the platen in addition to ordinary sheet originals.
Open the original cover, and place the original.
Note Shadows may be produced around the edges and in the middle of open-faced originals.
IMPORTANT Do not push the original cover forcefully when you close it. Excessive
pressure may crack the platen. (Allowable load weight: 5 kg or less)
When placing books or magazines on the machine, do so with the original cover in the open
position.
Align it flush against the
original size indicator plates
with the back left corner as the
reference point.
Put the scanning
side facedown.
2-17
Preparation
Installing and Uninstalling Drivers and Utilities
This section explains how to configure machine settings and install the software required for use as a machine. Ensure the
machine is plugged in and connected to the PC before installing the software from the Product Library disc.
Software
The following software can be installed from the provided Product Library disc.
: Installed standard. : Installed if selected.
Note Install the software when the machine status is online*.
*01 (in copy mode) or P0 (in scan or Print Box mode) appears in the operation panel display.
Software Function Description
Installation Method Reference
Page
Express
Install
Custom
Install
GX DRIVER Print Driver for printing files on a computer using
the machine. This printer driver enables full
use of the machine’s features.
Printer
Driver User
Guide
GX XPS DRIVER Printer driver for XPS (XML Paper
Specification) format developed by Microsoft
Corporation.
—
TWAIN Driver Scan Driver for scanning on the machine using a
TWAIN-compatible software application.
5-5
WIA Driver WIA (Windows Imaging Acquisition) is a
function of Windows that enables reciprocal
communication between an imaging device
such as a scanner and an image processing
software application. An image can be
acquired using a WIA-compliant software
application, which is convenient when a
TWAIN-compliant software application is not
installed in the computer.
5-5
KYOCERA Net
Viewer
Utility Utility that enables the machine to be
monitored when connected to a network.
—KYOCERA
Net Viewer
User Guide
KYOCERA Client
Tool
Utility that enables current and all supported
devices status, features and settings to be
accessed.
When KYOCERA Client Tool is installed, the
following utilities are installed.
•Status Monitor (page 2-27)
•Preset Tool (page 2-28)
•Configuration (page 2-36)
•Maintenance Menu (page 6-7)
2-22
2-18
Preparation
Installing the Software in Windows
If you are connecting this machine to a Windows PC, follow the next steps to install the software. The example shows you
how to connect your machine to a Windows 7.
You can use either Express Install or Custom Install to install the software. Express Install automatically detects connected
machines and installs the required software. Use Custom Install if you want to specify the printer port and select the
software to be installed.
1Turn on the computer and start up Windows.
If the Welcome to the Found New Hardware Wizard screen displays, select Cancel.
2Insert the Product Library disc supplied with the machine into the optical drive. In Windows
7, Windows Server 2008 and Windows Vista, the user account control window may appear.
Click Yes.
The installation program launches.
3Click View License Agreement and read the License Agreement. Click Accept.
The software install wizard starts up.
From this point, the procedure differs depending on your version of Windows and your
connection method. Proceed to the correct procedure for your connection type.
•Express Install
•Custom Install
Express Install
In Express Install, the installer automatically detects the machine when it is turned on. Use Express Install for standard
connection methods.
1Select the Express Install tab. The installer detects the machine.
If the installer does not detect a print system, check that the print system is connected via
USB and that it is turned on. Then click (Refresh) to search print system again.
Note In Windows operating systems, you must be logged in with administrator privileges to install the software.
Note If the software install wizard does not launch automatically, open the Product
Library disc window in Windows Explorer and double-click Setup.exe.
Note While the information shown in Windows 7 and Windows Vista/Windows XP
installation dialog boxes differs slightly, the installation procedure is the same.
2-19
Preparation
2Select the machine you want to install, select the Driver Package, and click Install.
3A message appears saying that your software is ready to use. To print a test page, select
the Print a test page checkbox and select the machine.
Click Finish to exit the installation wizard.
This completes the software installation procedure.
Custom Install
Use Custom Install if you want to specify the printer port and select the software to be installed.
1Select Custom Install tab.
2Select the device to be installed, and click the arrow button to move it to the Products to
Install list.
3Select the software to be installed, and click the arrow button to move it to the Products to
Install list.
4Click Install.
5A message appears saying that your software is ready to use. To print a test page, select
the Print a test page checkbox and select the machine.
Click Finish to exit the installation wizard.
This completes the software installation procedure.
Installation on a Macintosh
This section explains how to install the printer driver in Mac OS.
1Turn on the machine and the Macintosh.
2Insert the Product Library disc supplied with the machine into the optical drive.
3Double-click the Product Library disc icon.
Note If the Found New Hardware Wizard appears, click Cancel. If a hardware
installation warning message appears, click Continue.
If the Windows security window appears, click Install this driver software anyway.
2-20
Preparation
4Double-click OS X 10.5 or higher.
5Double-click Kyocera OS X 10.5+ xxxxx.
6The printer driver installation program starts up.
7Install the printer driver as directed by the instructions in the installation software.
This completes the printer driver installation.
IMPORTANT In the Authentication screen, enter the name and password used to log
in to the operating system.
2-21
Preparation
Uninstalling Drivers and Utilities
The software can be uninstalled (removed) using the Product Library disc supplied with the machine.
1Exit all active software applications.
2Insert the Product Library disc supplied with the machine into the optical drive. In Windows
7, Windows Server 2008 and Windows Vista, the user account control window may appear.
Click Yes.
3Following the procedure used to install the software, click Uninstall tab.
4Select the software package to remove.
5Click Uninstall.
The uninstaller starts.
6When Uninstall complete screen appears, click Finish.
7If Restart Your System screen appears, select whether you restart your computer or not,
and click Finish.
IMPORTANT On Macintosh computers, because the machine settings are specified using a PPD (PostScript Printer
Description) file, the software cannot be uninstalled using the Product Library disc.
Note When KYOCERA Net Viewer is installed, separate uninstallers are launched for this application. Proceed with
the uninstallation steps for this application as directed by the on-screen instructions.
2-22
Preparation
Machine Settings
Various machine settings can be configured from a computer using KYOCERA Client Tool. Install KYOCERA Client Tool
from the provided Product Library disc.
Accessing KYOCERA Client Tool
Start KYOCERA Client Tool.
KYOCERA Client Tool Functions
The functions of KYOCERA Client Tool are described below.
Note For the detailed functions of KYOCERA Client Tool, refer to KYOCERA Client Tool User Guide.
Function Description Reference Page
KYOCERA Client Tool KYOCERA Client Tool gives you quick access to common
machine features and settings, plus the current status of all
supported machines. You can also use KYOCERA Client Tool to
order toner, download printer drivers, access KYOCERA Net
Viewer, open the company website and view machine
documentation.
2-23
Status Monitor Lets you view the status of the machine on your desktop. 2-27
Preset Tool Registers the Copy, Scan and Print Box programs. 2-28
Configuration Allows user to configure machine settings, including energy saving
and paper settings. Messages shown in the Status Monitor are
also configured here.
2-36
Maintenance Menu For machine maintenance. Use when print quality deteriorates or
to adjust the print or scan position.
6-7
2-23
Preparation
KYOCERA Client Tool Settings
General
No. Item Description Reference
Page
1Machine list The list at the top of KYOCERA Client Tool screen
includes all of the supported machines installed on
your computer. You can select a machine from this
list to view its properties and select available options,
such as configuration, maintenance, and driver
download.
—
2Print The Print tab gives you access to printing
preferences and machine driver properties. Click
Preferences or Properties to open the settings.
2-24
3 Device The Device tab lets you configure a machine, view
documentation, restart a machine and restore factory
default settings.
Click Configuration to display the Configuration
screen. This lets you configure various machine
settings. Refer to Configuration on page 2-36.
2-25
4 Scan The Scan tab lets you configure TWAIN and Quick
Scan settings.
Scan to PDF, Scan to Email and Scan to Folder can
also be executed from this tab.
2-25
1
2
6
7
3
4
8
5
2-24
Preparation
Print Tab
5 Maintenance The Maintenance tab lets you open KYOCERA Net
Viewer*, order replacement toner, view our web site,
and download software.
Click Maintenance Menu to display the
Maintenance Menu screen. This lets you perform
machine maintenance. Refer to Maintenance Menu
on page 6-7.
2-26
6Machine status This shows a 3D image of the selected machine and
its current status. Click (Refresh) to refresh the
machine status.
—
7 Supplies The Supplies tab shows the toner status. —
Device Overview The Device Overview tab shows the machine
settings.
—
8Close Clicking Close exits KYOCERA Client Tool. —
* To display KYOCERA Net Viewer, KYOCERA Net Viewer must be installed.
No. Item Description Reference
Page
No. Item Description
1 Preferences Opens the Printing Preferences screen for the selected machine.
2 Properties Opens the Properties screen for the selected machine.
1
2
2-25
Preparation
Device Tab
Scan Tab
No. Item Description Reference
Page
1 Configuration Opens the Configuration screen for the selected
machine.
2-36
2 Preset Opens the Preset Tool screen for the selected
machine.
2-28
3 Documentation Opens the folder where manuals are contained. —
4 Device restart Click the Device restart icon to restart the machine.
Click Yes to confirm. You must be logged in with
administrator privileges on your PC.
—
5 Factory default Click the Factory default icon to return all of the
machine properties of the selected model to its
default settings. Click OK to confirm. You must be
logged in with administrator privileges on your PC.
—
1
2
3
5
4
No. Item Description Reference
Page
1 Preferences Opens TWAIN screen. Set the default value for the
TWAIN scan.
2-34
2 Quick Scan
Settings
Opens Quick Scan screen. 2-34
3 Scan to PDF Saves the scanned image in PDF format. 5-4
4 Scan to Email Attaches the scanned image to a new E-mail
message.
5-4
5 Scan to Folder Saves the scanned image to a specified folder. 5-4
1
2
3
5
4
2-26
Preparation
Maintenance Tab
No. Item Description Reference Page
1 Maintenance
Menu
Opens Maintenance Menu screen. 6-7
2 KYOCERA Net
Viewer
Opens KYOCERA Net Viewer.*
* To display KYOCERA Net Viewer, KYOCERA Net Viewer must be installed.
KYOCERA Net
Viewer User Guide
3 Order Toner You can order replacement toner by e-mail or
on the web. Click the Order Toner icon for
these options:
•Send e-mail
Use the default e-mail address or type
another e-mail address and then click OK
to open your default e-mail program.
•Open Web page
Use the default web address or type
another web address and then click OK to
open the web page in your default web
browser.
—
4 Kyocera Online Opens our website. —
5 Driver Download Click to open the download page of our
website. You can download software and find
an authorized dealer.
—
1
2
4
5
3
2-27
Preparation
Status Monitor
When KYOCERA Client Tool is installed, you can check the machine status in the Status Monitor icon.
The Status Monitor icon displays machine status messages in the lower right corner of the screen.
Screen Overview
The screen overview of the Status Monitor icon is as follows.
When the Status Monitor icon is active, you can select KYOCERA Client Tool options by
right-clicking the icon in the system tray.
No. Item Description
1Pop-up window If an information notification event occurs, a pop-up window
appears.
Information notification events can be set in the Configuration.
Refer to Configuration on page 2-36.
2Status Monitor
icon
The Status Monitor icon is displayed in the taskbar notification
area when the Status Monitor is running.
No. Item Description
1 Show/Hide the
KYOCERA Client Tool
Switches between hiding and showing KYOCERA Client
Tool screen.
2(URL) Opens our website.
3Exit Closes KYOCERA Client Tool and removes the Status
Monitor icon from the system tray.
1
2
1
2
3
2-28
Preparation
Default and Program Settings
This section explains about the Copy, Print Box, and Scan default settings and programs. For settings that are frequently
changed from the default settings, it is convenient to register a program.
Default Settings
This section explains the default settings for each function.
Program Settings
If you have settings that are frequently changed from the default settings, register the settings in a program. You can
simply select the program number as needed to recall those functions.
Programs can be registered from a computer using Preset Tool. The Preset Tool is a function of KYOCERA Client Tool.
Three programs can be registered per function.
This section explains how to register a program. To use a registered program, refer to the pages of each function.
•Copy: Basic Operation on page 3-2
•Scan: Push Scan on page 5-2
•Print Box: Printing from Print Box on page 4-6
Accessing the Preset Tool
1Start KYOCERA Client Tool as explained in Accessing KYOCERA Client Tool on
page 2-22.
2Click Preset on the Device tab. The Preset Tool opens.
Functions Description
Copy The default settings for Copy are changed with the Configuration. For details, refer to
Configuration on page 2-36.
Print Box It is not possible to change the default settings for Print Box. The job stored in the Default
folder is printed. The Program is used to select the Print Box. Refer to Program Settings on
page 2-28.
Push Scan It is not possible to change the default settings for Push Scan. The Program is used to change
the settings. Refer to Program Settings on page 2-28.
2-29
Preparation
General
3
1
2
6
7
8
4 5
No. Item Description Reference
Page
1Program number Select the program number (1 to 3) to be registered. When a program number is
selected, the settings registered in that number appear in the right-hand screen.
—
2Summary Shows a list of the settings of the selected program. —
3Copy Set programs for the Copy function. 2-30
4 Scan Set programs for the Scan function. 2-32
5Print Box Set programs for the Print Box function. 2-33
6 Reset Reset the program to default values. —
7 Save Save your settings. —
8Close Close the Preset Tool. —
2-30
Preparation
Copy Tab
1
2
3
4
5
7
8
9
10
11
6
No. Item Description
1 Original size Specify the size of originals being scanned.
Value: Executive, Letter, A4, A5, A6, B5 (JIS), B5 (ISO), Custom, 16K, Statement
Note Refer to Configuration on page 2-36 for selecting Custom.
2 Original image Select image quality suited to the type of original.
Value:
3 Resolution The resolution is selected when Text + Photo is selected in Original image. Select
600 dpi when you want good reproduction of fine text and lines in originals which
contain a mixture of text and photos.
Value:
Note The Photo and Text selections in Original image are fixed at 300 dpi.
4Copies* Set the default value for the number of copies.
Value: 1 to 99
5Collate Scan multiple originals and deliver complete sets of copies as required according to
page number.
Value:
6 Original orientation Select the orientation of the original document top edge to scan correct direction.
Value:
Text + Photo Photo Text
300 dpi 600 dpi
Off On
Top Edge Left Top Edge Top
2-31
Preparation
7Zoom Adjust the magnification to reduce or enlarge the original image.
Value: 100%, Auto, Custom, Fixed
When Custom or Fixed is selected, the Zoom screen is displayed.
8 Density Adjust density using 7 levels.
Value: Lighter (-3), Lighter (-2), Lighter (-1), Normal (0), Darker (+1), Darker (+2),
Darker (+3)
9EcoPrint Use EcoPrint to save toner when printing. Use this function for test copies or any other
occasion when high quality print is not required.
Value:
10 Combine Combine 2 or 4 original sheets into 1 copied page.
Value:
11 Layout You can select the page layout.
Value:
* Non-numeric characters cannot be entered. If entered number is beyond range, the max/min value will be
restored.
No. Item Description
Zoom level (Fixed)
Adjusts the image to match present
sizes.
Custom*
Specify the image size in 1% increment
between 25% - 400% of the original.
On Off
Off 2in1 4in1
2in1 4in1
Left to right Right to left
Right then
down
Down then
right
Left then
down
Down then
left
2-32
Preparation
Scan Tab
1
2
3
4
9
5
6
7
11
12
8
10
No. Item Description
1Name Set a name for the Program. Up to 18 characters can be entered.
2 Original size Specify the size of originals being scanned.
Value: Executive, Letter, A4, A5, A6, B5 (JIS), B5 (ISO), Custom, 16K, Statement
Note Refer to Configuration on page 2-36 for selecting Custom.
3 Original image Select image quality suited to the type of original.
Value:
4 Reverse image When this is selected, the image color reverses.
5Sharpen Adjust the sharpness of the image.
Value: None, Low, Medium, High, Descreen (Blurs the outlines and reduces the
sharpness.)
6 Scan color Select the color mode setting.
Value: Monochrome, Grayscale, Full color
7 Density Select the density.
Value: Lighter (-3), Lighter (-2), Lighter (-1), Normal (0), Darker (+1), Darker (+2),
Darker (+3)
8 Resolution Select fineness of scanning resolution.
Value:
9 Output name Assign a document name to scanned images. When there are multiple pages, a
three-digit incrementing number such as Scan_001, Scan_002... is appended to the
end of the file name. Up to 16 characters can be entered.
10 File format Specify the image file format.
Value: BMP, JPEG, PNG, TIFF, PDF
Text + Photo Photo Text
200×200 dpi 300×300 dpi 400×400 dpi 600×600 dpi
2-33
Preparation
Print Box Tab
11 Quality Set the quality if file format is JPEG. This is disabled for non-JPEG format.
Value: 1 to 100
Note Non-numeric characters cannot be entered. If entered number is beyond range,
the max/min value will be restored.
12 Destination folder Enter the path of the folder where the scanned image will be saved. Either
C:\User\<user>\My Documents (on Windows Vista/Windows 7) or C:\Document and
Settings\<user>\My Documents (on Windows XP) is set as the default.
Enter the path of the folder where the scanned image will be saved. To select the
folder, click Browse to open Browse for Folder.
No. Item Description
1
2
No. Item Description
1Name Set a name for the Program. Up to 18 characters can be entered.
2 Destination folder Enter the path for the folder to be used as the Print Box. Program 1 is Box 1,
Program 2 is Box 2 and Program 3 is Box 3.
To select the folder, click Browse to open Browse for Folder.
2-34
Preparation
Quick Scan/TWAIN Settings
Settings required for scanning on the machine are explained below. The settings specified here will be the default settings
for scanning.
1Start KYOCERA Client Tool as explained in Accessing KYOCERA Client Tool on
page 2-22.
2Click Preferences or Quick Scan Settings on the Scan tab.
TWAIN Settings
Item Description
Preferences Change the TWAIN scan settings. This setting is effective for Quick Scan only.
Quick Scan Settings Change the settings for Scan to PDF, Scan to Email and Scan to Folder.
No. Item Description
1 Original size Specify the size of originals being scanned.
Value: Letter, Statement, Executive, A4, A5, A6, B5 (JIS), B5
(ISO), 16K, Custom
Note Refer to Configuration on page 2-36 for selecting Custom.
2 Scan color Select the color mode setting.
Value: Monochrome, Grayscale, Full color
3 Resolution Select fineness of scanning resolution.
Value: 200 × 200 dpi, 300 × 300 dpi, 400 × 400 dpi,
600 × 600 dpi
4Sharpen Adjust the sharpness of the image.
Value: None, Low, Medium, High, Descreen (Blurs the outlines
and reduces the sharpness.)
1
2
3
8
4
5
6
7
910
2-35
Preparation
Quick Scan Settings
5 Original image Select original image type for best results.
Value: Text, Photo, Text+Photo
6 Destiny Select the density.
Value: -3 (Lighter) to 3 (Darker)
7 Reverse image When this is selected, the image color reverses.
8 Reset Reset the settings to the previous settings.
9Help Displays the Help screen.
10 OK/Close Clicking OK exits the TWAIN Settings after applying the modified
scan settings.
Clicking Close exits the TWAIN Settings without applying the
modified scan settings.
No. Item Description
No. Item Description
1 Output name Assign a document name to scanned images. When multiple
images are saved in the same folder, a three-digit incrementing
number such as Scan_001, Scan_002... is appended to the end of
the file name. Up to 16 characters can be entered.
2 File format Specify the image file format.
Value: BMP, JPEG, PNG, TIFF, PDF
Note In Scan to PDF, all images are saved in PDF format.
3Quality Set the image quality if File format is JPEG. The higher quality
becomes the lower compression. This is disabled for non-JPEG
format.
Value: 1 to 100
Note Non-numeric characters cannot be entered. If entered
number is beyond range, the max/min value will be restored.
4 Preferences Displays the TWAIN settings screen. For detail, refer to TWAIN
Settings on page 2-34.
5 OK/Cancel/Apply Clicking OK exits the Quick Scan Settings after applying the
modified scan settings.
Clicking Cancel exits the Quick Scan Settings without applying the
modified scan settings.
Clicking Apply applies the modified scan settings without exiting
the Quick Scan Settings.
1
4
5
2
3
2-36
Preparation
Configuration
The Configuration is a function of KYOCERA Client Tool. The default settings of the machine can be changed and the
messages that appear in the Status Monitor can be set.
Accessing the Configuration
Follow these steps to display the Configuration on the desktop.
1Start KYOCERA Client Tool as explained in Accessing KYOCERA Client Tool on
page 2-22.
2Click Configuration on the Device tab. The Configuration opens.
Note For the detailed functions of the Configuration, refer to KYOCERA Client Tool User Guide.
2-37
Preparation
Configuration Screen
General
5
1
4
2
3
No. Item Description Reference
Page
1 Device Defaults Configure overall machine operation. 2-38
2Copy Configure settings for copying functions. 2-40
3 Status Monitor Configure settings for the Status Monitor. 2-41
4 OK/Cancel/Apply Clicking OK exits the Configuration after applying the modified machine
settings.
Clicking Cancel exits the Configuration without applying the modified
machine settings.
Clicking Apply applies the modified machine settings without exiting the
Configuration.
—
5— Close the Configuration. —
2-38
Preparation
Device Defaults Tab
12
3
4
5
7
8
910
11
12
6
13
14
15
No. Item Description
1 Power off timer Select the length of time before the machine shuts off automatically when not in use.
The default preset time is 1 hour.
Value: 1 to 6 hours, 9 hours, 12 hours, 1 day to 1 week
Also, selects whether or not to turn the power off automatically when a USB is
connected.
Note Power off when does not appear on the FS-1020MFP for Europe, Russia, Africa
and Middle East, and FS-1220MFP for Europe.
2 Auto sleep Set the sleep timer for the machine to go into sleep mode when not in use. The default
preset time is 1 minute.
Value: 1 to 240 minutes (1 minute increments)
3Quiet mode Turn on Quiet Mode. Refer to Quiet Mode on page 1-4.
4Units Select Inches or Millimeters for the unit for paper dimensions.
5 Print density Adjust density using 5 levels.
Value: Light, Medium light, Normal, Medium dark, Dark
6 Panel options Opens Panel options screen.
• Default screen: Select the screen appearing right after
start-up (default screen).
Note To enable the change immediately, turn the
machine OFF and then ON. Otherwise wait until the
machine once enters the sleep and then resumes.
• Reset panel: If no jobs are run for a certain period of
time, automatically reset settings and return to the
default setting. If you select On for Reset panel, set the
amount of time to wait before Reset panel.
2-39
Preparation
7 Auto error clear Enable auto error clear. If an error occurs during processing, processing stops to wait
for the next step to be taken by the user. In the auto error clear mode, automatically
clear the error after a set amount of time elapses.
If you select On for auto error clear, set the amount of time to wait before automatically
clearing errors.
Value: 5 to 495 seconds (every five seconds)
8 Form feed timeout When receiving print data from the computer, the machine may sometimes wait if there
is no information signaling that the last page does not have any more data to be
printed. When the preset timeout passes, the machine automatically prints the
documents. The options are between 5 and 495 seconds.
Value: 5 to 495 seconds (every five seconds)
9 Paper size Set the default paper size to load in the cassette.
Value: Letter, Legal, Statement, Executive, A4, A5, A6, Folio, B5 (JIS), B5 (ISO),
Oficio II, 216 × 340 mm, 16K, Custom size
When a Custom size is selected, the Custom Paper size screen appears.
Type or select values for Width and Length. If the Width or
Length value exceeds the allowable limit, it automatically
adjusts to the limit after OK is clicked.
10 Original size Set the default original size to be scanned.
Value: Letter, Statement, Executive, A4, A5, A6, B5 (JIS), B5 (ISO), 16K, Custom
size
When a Custom size is selected, the Custom Original size screen appears.
Type or select values for Width and Length. If the Width or
Length value exceeds the allowable limit, it automatically
adjusts to the limit after OK is clicked.
11 Original image Set the default image quality.
Value: Text + Photo, Photo, Text, Text + High resolution photo
12 Media type Set the default media type to load in cassette.
Value: Plain, Preprinted, Labels, Bond, Recycled, Vellum (60 to 64 g/m²), Rough,
Letterhead, Color, Prepunched, Envelope, Cardstock, Thick (90 to 220 g/m²), High
quality, Custom 1-8
When Custom 1-8 is selected, the Custom name appears.
13 Custom name Change names for Custom 1-8. Selecting media type, the name after change will be
displayed.
14 Paper weight Select weight for each media type. For details, refer to Paper Type on page 2-11.
Value: Light, Normal 1, Normal 2, Normal 3, Heavy 1, Heavy 2, Heavy 3
15 Save Save the Paper weight and Custom name settings that are set for Custom 1-8.
No. Item Description
2-40
Preparation
Copy Tab
13
2
4
5
No. Item Description
1Collate Select the defaults for Collate.
2Orientation Set the original orientation defaults.
Value: Top edge top, Top edge left
3EcoPrint Select the EcoPrint default.
4Zoom Select the default zoom setting.
Value: Auto, 100%
5 Density Set the default value for the copy density.
Value: Lighter (-3), Lighter (-2), Lighter (-1), Normal, Darker (+1), Darker (+2),
Darker (+3)
2-41
Preparation
Status Monitor Tab
1
2
3
4
5
6
No. Item Description
1 Set toner level alert Select to create an alert when the toner starts running low, and then select a
percentage between 0 and 100. If the toner level goes below this percentage, an alert
icon is displayed on the Supplies tab at the bottom of KYOCERA Client Tool screen.
2 Enable event
notification
Select to activate the notification feature for selected machine events. When selected,
notification options are available.
3 Enable pop-up
notification
When selected, a pop-up message appears in the lower right corner of the screen for
each selected event as it occurs.
4Events list Select one or more events for the notification. To select all events, select Events.
5 Sound file With one or more events selected, select to enable sound notification. Type the
location of a sound file (.WAV), or click Browse to find a sound file located on your
computer. You can press the arrow button to hear the selected sound.
6 Use Text to Speech With one or more events selected, select and type your preferred text. The Microsoft
Text to Speech utility reads the text and plays it in a spoken voice. You can press the
arrow button to hear the selected text.
2-42
Preparation
Printing the Status Page
You can print the Status Page to check the current settings.
To print the status page, hold down the Mode Select key for 5 seconds.
3-1
3Copying
This chapter explains the following topics:
Basic Operation...................................................................................................................................................... 3-2
Manual Duplex........................................................................................................................................................ 3-3
Using Programs ..................................................................................................................................................... 3-5
Copying Functions................................................................................................................................................. 3-5
ID Card Copy .......................................................................................................................................................... 3-6
3-2
Copying
Basic Operation
Follow the steps as below for basic copying.
1Configure necessary settings in KYOCERA Client Tool in advance. Refer to Machine
Settings
on page 2-22.
2Press [Copy].
3Place the originals. For details, refer to Loading Originals on page 2-16.
4To use a program, select the program number (P0 to P3).
Press the Mode Select key to select Program, and press [] or [] to select the program
number.
5Enter the number of copies.
Press the Mode Select key to select Copies, and press [] or [] to enter the number of
copies.
6Adjust density using 7 levels (-3 (Lighter) to 3 (Darker)).
Press the Mode Select key to select Density, and press [] or [] to select your desired
density.
7Press [Start] to start copying.
Note For details on functions that are registered in programs, refer to Using
Programs on page 3-5.
P0 is the status with no program set.
3-3
Copying
Manual Duplex
To copy on both sides of the paper, use Manual Duplex.
1Select copy functions and place the front-side original (or odd numbered page) as
explained in Basic Operation on page 3-2.
2Press [Start] to start copying. The front side is copied.
3Retrieve the paper from the inner tray. If copying on multiple sheets, fan through the sheets
to separate them prior to loading.
If the paper is curled at an edge, straighten it prior to reloading.
3-4
Copying
4Copy the back side (or even numbered page). Load the paper as shown.
5Place the back-side original (or even numbered page). For details, refer to Loading
Originals on page 2-16.
6Press [Start]. The back side is copied, and duplex copying is completed.
Long Edge Binding Short Edge Binding
(Finished)
(Finished)
3-5
Copying
Using Programs
If there are settings that you frequently change from the default state, register the settings in a program. You can simply
select the program number as needed to recall those functions.
Copy functions can be registered in three programs.
The programs below have been preregistered. The registered contents can be re-registered for easier use in your
environment.
Copying Functions
Copying functions are as follows. These functions are all configured from KYOCERA Client Tool.
Item Program1 Program2 Program3
Original size A4 (Letter) A4 (Letter) A4 (Letter)
Original image Text Text+Photo (300 dpi) Photo
Copies 1 1 1
Collate On On On
Original orientation Top Edge Top Top Edge Top Top Edge Top
Zoom Auto Auto Auto
Density Darker (+3) Lighter (-2) Normal (0)
EcoPrint Off On Off
Combine Off 2in1 (Left to right) Off
Note For details on program registration and the various functions, refer to Program Settings on page 2-28.
Refer to Basic Operation on page 3-2 for recalling programs.
Item Description
Original size Specify the size of originals being scanned.
Value: Executive, Letter, A4, A5, A6, B5 (JIS), B5 (ISO), Custom, 16K, Statement
Original image Select image quality suited to the type of original.
Value: Text + Photo (300 dpi or 600 dpi), Photo, Text
Collate*
* When this function is selected, printing starts after all pages to be copied are scanned. Place one page at a time
and press [Start]. When you have finished scanning all pages, press [] or [] to select - and press [Start]
again to start printing.
Scan multiple originals and deliver complete sets of copies as required according to page
number.
Value: Off, On
Zoom Adjust the magnification to reduce or enlarge the original image.
Value: 100%, Auto, Fixed, Custom
Density Adjust density using 7 levels.
Value: Lighter (-3), Lighter (-2), Lighter (-1), Normal (0), Darker (+1), Darker (+2), Darker (+3)
EcoPrint Use EcoPrint to save toner when printing. Use this function for test copies or any other occasion
when high quality print is not required.
Value: Off, On
Combine* Combine 2 or 4 original sheets into 1 copied page. You can select the page layout.
Value: Off, 2in1, 4in1
Note To set a function from KYOCERA Client Tool, refer to Default and Program Settings on page 2-28.
3-6
Copying
ID Card Copy
Use to copy the front and back sides of a license or other ID card on one sheet of paper.
1Press [ID Card Copy].
2Place the original. Align with the ID Card marks on the Original Size Indicator Plates.
For details, refer to Loading Originals on page 2-16.
3Enter the number of copies. (Refer to Basic Operation on page 3-2.)
4Adjust density. (Refer to Basic Operation on page 3-2.)
5Press [Start]. 1- appears in the display on the operation panel and the first side of the card
is scanned.
After the first side is scanned, 2- appears in the display.
6Turn the original over. Align with the ID Card marks on the Original Size Indicator Plates.
7Press [Start]. The front and back sides of the card are copied on one sheet of paper.
ID Card
ID Card
ID Card
ID Card
4-1
4Printing
This chapter explains the following topics:
Printing from Application Software...................................................................................................................... 4-2
About GX Driver ..................................................................................................................................................... 4-2
Manual Duplex........................................................................................................................................................ 4-3
Print Box ................................................................................................................................................................. 4-5
Changing the Default Printer Driver Settings (Windows 7 for example)........................................................... 4-6
4-2
Printing
Printing from Application Software
The steps required to print a document created with an application are explained below. You can select the printing paper
size.
1Load the paper required into the cassette.
2From the application File menu, select Print. The Print screen appears.
3Click the drop-down list of printer names. All the installed printers are listed. Click the name
of the printer.
4Use Number of copies to enter the number of copies required. Up to 999 copies can be
printed. For Microsoft Word, we recommend that you click Options and specify Use
printer settings for the Default tray.
5To start printing, click OK.
About GX Driver
GX Driver consists of the following tabs.
Note You can also select the various settings by clicking Properties to open the Properties screen. Refer to About
GX Driver.
Tabs Description
Quick Print Use this tab to define basic print options into group profiles that
can be accessed quickly and easily.
Basic Use this tab to select the page size and orientation. The paper
source is also selected.
Layout Use to create multiple pages on a single sheet of paper. Also
contains the scaling option.
Imaging Select this tab to change the print quality and graphic settings.
Job Use to save a print job in a Print Box. Refer to Print Box on
page 4-5.
Advanced Use to set up and add watermarks to your output.
4-3
Printing
Manual Duplex
To print on both sides of the paper, use Manual Duplex. The even pages are printed first and then reloaded to print the odd
pages. An instruction sheet is available to assist with loading the sheets in the correct orientation and order.
1Select Print on both sides (manual duplex).
Select Flip on long edge if the binding will be on the long edge or Flip on short edge if
the binding will be on the short edge. Select Print manual duplex instructions to receive
the instruction sheet.
2Select OK to return to the Print screen and select OK to start printing. A Manual Duplex
Instruction message box displays. The even pages are printed including the instruction
sheet.
3Remove all the even pages (including the instruction sheet) from the inner tray, fan through
the sheets to separate them prior to loading.
If the paper is curled at an edge, straighten it prior to reloading.
Note Ensure Print manual duplex instructions is selected to receive the instruction sheet. Continue to use the
sheet until you are familiar with this feature.
Note Instructions for manual duplex will be printed on the instruction sheet.
4-4
Printing
4Load the even pages printed into the cassette with the instruction sheet facing down and
the arrows pointing toward the machine.
5Select OK in the Manual Duplex Instruction message box of the printer driver screen. All
the odd pages will be printed.
Note If the paper is considerably curled in one direction, roll the paper in the opposite
direction to counteract the curl. If this will not cancel the curl satisfactorily, try to
reduce the number of sheets loaded in the cassette to the maximum of 100.
Manual Duplex Instructions
Long Edge Binding
Manual Duplex Instructions
Short Edge Binding
Long Edge Binding Short Edge Binding
(Finished)
(Finished)
4-5
Printing
Print Box
A print job can be saved in Print Box in the computer and printed from the machine when needed. Use the machine's
operation panel to print the print job stored in a Print Box.
The four possible selections for the Print Box are the Default box and Boxes 1 - 3.
Saving to a Print Box
Save a print job to a Print Box.
1From the application File menu, select Print. The Print screen appears.
2Click Properties. The Properties screen appears.
3Select Job tab.
4Select Job storage then select the Print Box where the print job should be stored from the
Default, Box 1, Box 2 or Box 3.
5Set the job name for the print job.
6Select OK to return to the Print screen and click OK to start storing.
Note The folder to be used for Boxes 1 - 3 can be set in the Preset Tool. Refer to Program Settings on page 2-28.
Settings Filename
Application define and
Don’t use application
name
<Document name> <month><day><year>
<hour><minutes><seconds>.prn
Example: PrintBox.docx
Filename: PrintBox 040112 030201.prn
Application define <Application name> <month><day><year>
<hour><minutes><seconds>.prn
Example: PrintBox.docx
Filename: Microsoft Word 040112 030201.prn
Custom and Use job
name + date and time
<Custom name> <month><day><year>
<hour><minutes><seconds>.prn
Example: Custom name is Print_A.
Filename: Print_A 040112 030201.prn
Custom and Replace
existing file
<Custom name>.prn
Example: Custom name is Print_A.
Filename: Print_A.prn
Note Any stored job with the same name will be overwritten.
4-6
Printing
Printing from Print Box
Print a print job saved in a Print Box.
1Press [Print Box]. P0 appears in the operation panel display.
2Press [] or [] to select the Print Box number (P0 to P3).
When P0 is selected, jobs saved in Default box are printed.
The following boxes are pre-registered in the Print Box Program.
P1: Box 1
P2: Box 2
P3: Box 3
3Press [Start] to start printing.
Changing the Default Printer Driver Settings (Windows 7 for example)
The default printer driver settings can be changed. By selecting frequently used settings, you can omit steps when printing.
The procedure is as follows.
1Click the start button, and then click Devices and Printers.
2Right-click the printer driver icon of the machine, and click the Printer properties menu of
the printer driver.
3Click the Printing Preferences button on the General tab.
4Select the default settings and click the OK button.
For the settings, refer to Printer Driver User Guide.
Note All print jobs saved in the selected Print Box are printed.
KYOCERA Client Tool must be running on the computer from which printing from Print Box is executed. Refer to
Machine Settings on page 2-22.
After being printed, the print jobs in the Print Box are deleted.
Note The folders for Boxes 1 - 3 can be changed with the Preset Tool. Refer to
Program Settings on page 2-28 for registering programs.
5-1
5 Scanning
This chapter explains the following topics:
Push Scan............................................................................................................................................................... 5-2
Using Programs ..................................................................................................................................................... 5-3
Quick Scan (Scan to PDF/Scan to Email/Scan to Folder) .................................................................................. 5-4
Scanning using TWAIN/WIA.................................................................................................................................. 5-5
5-2
Scanning
Push Scan
It is easy to scan from the operation panel on the machine. Push Scan performs scanning with the following settings. P0 is
the status of scanning without using the preset program.
1Press [Scan]. P0 appears in the display on the operation panel.
2Place the originals. For details, refer to Loading Originals on page 2-16.
3To use a program, select the program number (P0 to P3).
Press [] or [] to select the program number.
Item Value
Original size If unit setting is inch: Letter
If unit setting is mm: A4
For details on unit setting, refer to Configuration on page 2-36.
Resolution 300 × 300 dpi
Reverse image Unchecked
Sharpen None
Original quality Text + Photo
Scan color Full color
Density Normal (0)
Output name Scan
File format PDF
Destination folder For Windows Vista/Windows 7: C:\Users\<user >\My Documents
For Windows XP: C:\Documents and Settings\<user>\My Documents
Note The Program is used to change the settings. Refer to Using Programs on page 5-3.
When using Push Scan, KYOCERA Client Tool must be running on the computer. Refer to Accessing KYOCERA
Client Tool on page 2-22.
Note For details on functions that are registered in programs, refer to Using
Programs on page 5-3.
5-3
Scanning
4Press [Start] to start scanning.
Using Programs
If there are settings that you frequently change from the default state, register the settings in a program. You can simply
select the program number as needed to recall those functions.
Scan functions can be registered in three programs.
The programs below have been preregistered. The registered contents can be re-registered for easier use in your
environment.
Item Program1 Program2 Program3
Name Folder 1 Folder 2 Folder 3
Original size A4 (Letter) A4 (Letter) A4 (Letter)
Original image Text Text + Photo Photo
Reverse image Off Off Off
Sharpen Low Low Low
Scan color Full color Full color Full color
Density Normal (0) Normal (0) Normal (0)
Resolution 300 × 300 dpi 300 × 300 dpi 300 × 300 dpi
Output name Scan Scan Scan
File format PDF PDF PDF
Quality———
Destination folder C:\User\<user>\My Documents (Windows Vista/Windows 7)
C:\Document and Settings\<user>\My Documents (Windows XP)
Note For details on program registration and the various functions, refer to Program Settings on page 2-28.
Refer to Push Scan on page 5-2 for recalling programs.
5-4
Scanning
Quick Scan (Scan to PDF/Scan to Email/Scan to Folder)
Execute scanning from KYOCERA Client Tool. With Quick Scan, the following 3 types of scan are possible.
Scan to PDF: Saves the scanned image in PDF format. The folder is specified after scanning.
Scan to Email: Attaches the scanned image to a new E-mail message.
Scan to Folder: Saves the scanned image to a specified folder.
1Place the originals. For details, refer to Loading Originals on page 2-16.
2Start KYOCERA Client Tool as explained in Accessing KYOCERA Client Tool on
page 2-22.
3Click Scan to PDF, Scan to Email or Scan to Folder icon on the Scan tab.
4Scan to PDF
Scanning begins. When scanning finishes, the Save PDF File As dialog appears. Specify
the PDF file name and the folder in which the image will be saved.
Scan to Email
Scanning begins. When scanning finishes, the mailer starts and the scanned image is
attached. Enter the address, subject and message, and then send.
Scan to Folder
The Browse for Folder dialog appears. Specify the folder in which the image will be
saved, and click [OK]. Scanning begins.
Note The folder in which the scanned image is saved and the file format can be set in advance in KYOCERA Client
Tool. Refer to Quick Scan/TWAIN Settings on page 2-34.
5-5
Scanning
Scanning using TWAIN/WIA
This section explains how to scan an original using TWAIN/WIA.
The procedure for scanning using the TWAIN driver is explained as an example. The WIA driver is used in the same way.
1Place the originals. For details, refer to Loading Originals on page 2-16.
2Activate the TWAIN compatible application.
3Select the machine using the application and display the TWAIN screen.
4Select scanning settings in the TWAIN screen that opens.
The settings that appear in the TWAIN screen are as follows.
Note For selecting the machine, see the Operation Guide or Help for each
application software.
No. Item Description
1Original size Specify the size of originals being scanned.
Value: Letter, Statement, Executive, A4, A5, A6, B5 (JIS),
B5 (ISO), 16K, Custom
Note Refer to Configuration on page 2-36 for selecting
Custom.
2 Scan color Select the color mode setting.
Value: Monochrome, Grayscale, Full color
3 Resolution Select fineness of scanning resolution.
Value: 200 × 200 dpi, 300 × 300 dpi, 400 × 400 dpi,
600 × 600 dpi
1
2
3
4 6
57
9
10
11 14
12 13
8
15
5-6
Scanning
4Sharpen Adjust the sharpness of the image.
Value: None, Low, Medium, High, Descreen (Blurs the
outlines and reduces the sharpness.)
5Original image Select original image type for best results.
Value: Text, Photo, Text+Photo
6 Density Select the density.
Value: -3 (Lighter) to 3 (Darker)
7 Reverse image When this is selected, the image color reverses.
8 Reset Reset the settings to the default value.
9Preview area Displays a preview of the scanned image. The image can be
enlarged, rotated, trimmed, or moved.
10 Details list Displays a list of the settings.
11 Help Displays the Help screen.
12 Pre-Scan Acquires a preview image.
13 Scan Performs the scan and returns the image to the application.
14 Close Close the TWAIN screen.
15 About Displays the driver version number.
No. Item Description
6-1
6 Maintenance
This chapter explains the following topics:
General Information ............................................................................................................................................... 6-2
Toner Container Replacement .............................................................................................................................. 6-2
Maintenance Kit Replacement .............................................................................................................................. 6-5
Cleaning the Machine ............................................................................................................................................ 6-5
Maintenance Menu ................................................................................................................................................. 6-7
Prolonged Non-Use and Moving of the Machine ................................................................................................ 6-8
6-2
Maintenance
General Information
This chapter describes basic maintenance tasks you can perform for the machine. You can replace the toner container
according to the machine's status:
Also, the internal parts need periodic cleaning.
Toner Container Replacement
The Attention indicator identifies the toner status at two stages of toner usage.
•When the machine becomes low on toner, the Attention indicator flashes and a message appears in KYOCERA
Client Tool. Note the replacement is not always necessary at this stage.
•If you ignore the above status and continue printing, E-0007 appears in the display on the operation panel, the
Attention indicator will light up just before the toner is used up and the machine will stop. The toner container must
then be replaced immediately.
In either case, replace the toner container.
Frequency of toner container replacement
According to ISO 19752 and EcoPrint switched off the toner container can print as follows (A4/Letter paper is assumed):
2,500 pages (FS-1020MFP) or 1,600 pages (FS-1220MFP).
You can print a status page to check how much toner remains in the toner container. The Toner Gauge in the consumables
status section on the status page shows a progress bar, which roughly represents how much toner is left in the toner
container.
Starter Toner Container
The toner container packed with the new machine is a starter toner container. The starter toner container lasts an average
of 700 pages.
Toner Kits
For best results, we recommend that you only use genuine Kyocera Parts and Supplies. Should any damage be caused by
the application of a toner other than the original toner, then this damage is excluded from the guarantee.
A new toner kit contains the following items:
•Toner Container
•Plastic waste bag for old toner container
•Installation Guide
Note Information Collection on Memory Chips - The memory chip attached to the toner container is designed to
improve convenience for the end user; to support the recycling operation of empty toner containers; and to gather
information to support new product planning and development. The information gathered is anonymous - it cannot
be associated to any specific individual and the data is intended to be used anonymously.
Note If Non-genuine toner is installed appears in KYOCERA Client Tool after the toner container is replaced, the
installed toner container is non-genuine.
The manufacturer assumes no responsibility for damage caused by a non-genuine toner.
We recommend that you only use genuine toner containers.
When you want to use the toner container currently installed, press the Mode Select key and [Stop/Reset]
simultaneously for 3 seconds or more.
Note Do not remove the toner container from the carton until you are ready to install it in the machine.
6-3
Maintenance
Replacing the Toner Container
This section explains how to replace the toner container.
1Open the front cover.
2Pull out the toner container.
3Take the new toner container out of the toner kit. Shake the new toner container at least 10
times as shown in the figure in order to distribute the toner evenly inside the container.
CAUTION Do not attempt to incinerate the Toner Container. Dangerous sparks may cause burns.
IMPORTANT During toner container replacement, temporarily move storage media and computer supplies (such as
floppy disks) away from the toner container. This is to avoid damaging media by the magnetism of toner.
KYOCERA Document Solutions Inc. is not liable against any damages or problems arising from the use of toner
containers other than those designated as original Kyocera toner containers. For optimum performance, it is also
recommended to use only the Kyocera toner containers which are specifically intended for use in your country or
region. If the toner container for another destinations is installed, the machine will stop printing.
Note You do not have to turn machine power off before starting the replacement. Any data that may be processing
in the machine will be deleted if you turn the machine power off.
Note Put the old toner container in the plastic bag (supplied with the new toner kit)
and discard it later according to the local code or regulations for waste disposal.
6-4
Maintenance
4Install the new toner container in the machine. Push in firmly until you hear a "click" sound.
5Close the front cover. Toner is replenished for about 4 seconds.
Note If the front cover does not close, check that the new toner container is installed
correctly (in step 4).
After use, always dispose of the toner container in accordance with Federal, State
and Local rules and regulations.
6-5
Maintenance
Maintenance Kit Replacement
When the machine prints 100,000 pages, a message is printed indicating that the maintenance kit should be replaced. The
maintenance kit must then be replaced immediately.
To replace the maintenance kit, contact your service representative.
Contents:
•Drum unit
•Developer unit
•Waste toner box
•Feed roller
•Lower paper feed guide
•Transfer roller
Cleaning the Machine
Clean the machine regularly to ensure optimum output quality.
Original Cover/Platen
Wipe the backside of the original cover and the platen with a soft cloth dampened with alcohol or mild detergent.
Interior of the Machine
To avoid print quality problems, the interior of the machine must be cleaned with every toner container replacement.
1Open the rear cover.
Note Do not use organic solvents or other strong chemicals.
6-6
Maintenance
2Use a clean, lint-free cloth to wipe dust and dirt off the metal and rubber rollers, conveying
unit, and paper feed unit.
IMPORTANT Take care not to touch the drum and transfer roller (black) during
cleaning.
Transfer Roller
Rubber Roller
Conveying Unit
Paper Feed Unit
Drum
Metal Roller
6-7
Maintenance
Maintenance Menu
The Maintenance Menu that the user can adjust from KYOCERA Client Tool is described below. In addition, also refer to
KYOCERA Client Tool User Guide.
Maintenance Menu Description
Adjust print
quality
Drum charge
setting
When print quality has deteriorated, the output of the main charger can be
changed to restore print quality.
Altitude setting If you are using the machine at an altitude of 1500 m or higher and print
quality has deteriorated, the Altitude setting can be used to restore print
quality.
Drum refresh Perform Drum refresh when images show streaking with white lines.
Adjust print
position
Printing start
position
Single-sided printing
Adjust the position of the printed
image.
Print margins Adjust the width of the top edge,
bottom edge, left edge and right edge
margins.
Note This setting is not effective for
the printing from the machine.
B
A: Left edge
B: Top edge
Top edge: +10
A
B
D
A: Left edge
B: Top edge
C: Right edge
D: Bottom edge
Top edge: +10
AC
6-8
Maintenance
Prolonged Non-Use and Moving of the Machine
Prolonged Non-use
If you ever leave the machine unused for a long period of time, remove the power cord from the wall outlet.
We recommend you consult with your dealer about the additional actions you should take to avoid possible damage that
may occur when the machine is used next time.
Moving the Machine
When you move the machine:
•Move it gently.
•Keep it as level as possible to avoid spilling toner inside the machine.
•Be sure to consult a service representative before attempting long distance transportation of the machine.
•Keep the machine horizontal.
Adjust scan
position
Scanning start
position
Adjust the position of the scanned
image.
Scan margins Adjust the width of the top edge,
bottom edge, left edge and right edge
margins.
Restore factory default Restore factory default settings.
WARNING If you are shipping the machine, remove and pack the developer unit and drum unit in a plastic
bag and ship them separately from the machine.
Maintenance Menu Description
Platen: -10
B
D
A: Left edge
B: Top edge
C: Right edge
D: Bottom edge
Top edge: +10
AC
7-1
7 Troubleshooting
This chapter explains the following topics:
Solving Malfunctions ............................................................................................................................................. 7-2
Error Messages ...................................................................................................................................................... 7-7
Clearing Paper Jams.............................................................................................................................................. 7-9
7-2
Troubleshooting
Solving Malfunctions
The table below provides general guidelines for problem solving.
If a problem occurs with your machine, look into the checkpoints and perform procedures indicated on the following pages.
If the problem persists, contact your service representative.
Symptom Checkpoints Corrective Actions Reference
Page
The screen does not
respond when the power
switch is turned on.
Check the power cord. Connect both ends of the power cord
securely.
2-2
Pressing [Start] does not
produce copies.
Is there a message on the machine
screen, KYOCERA Client Tool, or the
Status Monitor?
Determine the appropriate response to
the message and respond accordingly.
7-7
Is the machine in Sleep mode? Press any key on the operation panel
to recover the machine from Sleep
mode.
—
The indicators are off
and the motor is not
working.
Check the power cord. Connect both ends of the power cord
securely.
2-2
— Press the power switch. —
The machine will not
print from the computer.
Check the power cord. Connect both ends of the power cord
securely.
2-2
Is the machine powered on? Turn on the power switch. —
Are the interface cable connected? Connect the correct interface cable
securely.
2-2
Was the machine powered on before
the interface cable was connected?
Power on the machine after
connecting the interface cable.
2-2
Is the print job paused? Resume printing. —
Is the Attention indicator lit or
flashing?
Does an error code appear in the
display on the operation panel?
Using the information on page 7-7,
check if an error has occurred and
clear the error.
If the indicators show a pattern not
described on page 7-7, turn the power
switch off and then on again. Print the
job again.
7-7
Check if a status page can be printed. If the status page was printed
successfully, there may be a problem
with the connection to the computer.
Check the connection. To print the
status page, refer to Printing the
Status Page on page 2-42.
2-2
The machine prints a
status page but data
from the computer is not
being printed.
Check the interface cable. Connect both ends of the interface
cable securely. Try replacing the
interface cable.
2-2
Check program files and application
software.
Try printing another file or using
another print command. If the problem
occurs with a specific file or
application, check the printer settings
for that application.
—
7-3
Troubleshooting
Vapor is emitted near the
inner tray.
Check if the temperature is low near
the location of the machine, or if the
paper that is being used has been
exposed to humidity.
Depending on the operating
environment of the machine and the
condition of the paper, heat generated
during printing can evaporate water
moisture in the printed paper, emitting
vapor from the machine. In this case,
printing can be continued without any
problem.
To correct this, increase the
temperature in the room, and use
paper that has been stored in a dry
place.
—
Blank sheets are
ejected.
Are the originals loaded correctly? When placing originals on the platen,
place them face-down and align them
with the original size indicator plates.
2-16
Full black printout or faint
printing.
— Open the rear cover and press the
points shown in the figure. If the
problem is not solved even after
printing several pages, call for service.
—
Paper often jams. Is the paper loaded correctly? Load the paper correctly. 2-11, 2-12
Is the paper of the supported type? Is
it in good condition?
Remove the paper, turn it over, and
reload it.
2-4
Is the paper curled, folded or wrinkled? Replace the paper with new paper. 2-4
Are there any loose scraps or jammed
paper in the machine?
Remove any jammed paper. 7-9
2 or more sheets are
overlaps when ejected.
(multi feed)
— Load the paper correctly. 2-11
Symptom Checkpoints Corrective Actions Reference
Page
7-4
Troubleshooting
Printouts are wrinkled. Is the paper damp? Replace the paper with new paper. 2-4
Printouts are curled. Is the paper damp? Replace the paper with new paper. 2-4
Text is missing on the
Windows test page.
— This is a problem specific to the
Windows OS. It is not a machine
problem. It does not affect print quality.
—
Printouts have dropouts
or stray dots.
Check the Drum charge setting in the
Maintenance Menu.
Increase the adjustment value for the
Drum charge setting in the
Maintenance Menu.
6-7
— Run Drum refresh in the Maintenance
Menu.
6-7
— The drum or developer unit may be
damaged. If the problem is not solved
even after printing several pages, call
for service.
—
Printouts have vertical
streaks
— The drum unit may be damaged. If the
problem is not solved even after
printing several pages, call for service.
—
Faint or blurred printing. Check the toner container. If necessary, replace the toner
container.
6-2
Check the Print density setting in
KYOCERA Client Tool.
Increase the adjustment value for the
Print density setting in KYOCERA
Client Tool.
2-38
Check the Drum charge setting in the
Maintenance Menu.
Decrease the adjustment value for the
Drum charge setting in the
Maintenance Menu.
6-7
Symptom Checkpoints Corrective Actions Reference
Page
7-5
Troubleshooting
The altitude is 1500 m or
higher and printouts are
too light.
Check the Altitude Setting in the
Maintenance Menu.
Set the Altitude Setting in the
Maintenance Menu to 1. If there is still
no improvement, change the value to
2.
6-7
Gray background. Check the toner container. If necessary, replace the toner
container.
6-2
Check the Drum charge setting in the
Maintenance Menu.
Increase the adjustment value for the
Drum charge setting in the
Maintenance Menu.
6-7
— Run Drum refresh in the Maintenance
Menu.
6-7
Check the Print density setting in
KYOCERA Client Tool.
Decrease the adjustment value for
Print density in KYOCERA Client
Tool.
2-38
Dirt on the top edge or
back of the paper.
Check the Drum charge setting in the
Maintenance Menu.
Increase the adjustment value for the
Drum charge setting in the
Maintenance Menu.
6-7
Is the interior of the machine dirty? If the problem is not solved even after
printing several pages, clean the
rollers, conveying unit and paper feed
unit.
If the problem is not solved after
cleaning, call for service.
6-5
The previous image
remains and lightly
printed on the
prepunched paper.
Check the Drum charge setting in the
Maintenance Menu.
Increase the adjustment value for the
Drum charge setting in the
Maintenance Menu.
Increase the adjustment value 1 level
at a time from the current value.
If there is no improvement after the
value is increased by 1 level, increase
by 1 level again.
If there is still no improvement, return
the setting to the original value.
6-7
Gray background with
horizontal streaks near
the top edge.
Check the Drum charge setting in the
Maintenance Menu.
Increase the adjustment value for the
Drum charge setting in the
Maintenance Menu.
6-7
Symptom Checkpoints Corrective Actions Reference
Page
7-6
Troubleshooting
Tips
Machine problems may be solved easily by following the tips below. When you have encountered a problem that cannot be
solved following the guidelines above, try the following:
•Restart the computer you are using to send print jobs to the machine.
•Obtain and use the latest version of the printer driver. The latest versions of printer drivers and utilities are available at:
http://www.kyoceradocumentsolutions.com.
•Make sure that the procedures for printing are correctly followed in the application software. Consult the
documentation supplied with the application software.
Copies have a moire
pattern (dots grouped
together in patterns and
not aligned uniformly).
Is the original a printed photograph? Set the image quality to Photo.2-30
Texts are not clearly
printed.
Did you choose appropriate image
quality for the original?
Select appropriate image quality. 2-30
Images are skewed. Are the originals placed correctly? When placing originals on the platen,
align them with the original size
indicator plates.
2-16
Is the paper loaded correctly? Check the position of the paper width
guides.
2-12
Are the application software settings at
the PC set properly?
Check that the printing settings are
correct in the application software and
the printer driver.
—
Cannot scan. Check the interface cable. Connect both ends of the interface
cable securely. Try replacing the
interface cable.
2-2
Is the save location correctly
specified?
Check the path to the folder where the
scanned image will be saved.
2-34
Symptom Checkpoints Corrective Actions Reference
Page
7-7
Troubleshooting
Error Messages
If a problem has occurred in the machine, you will be notified by the following display.
•The Attention indicator on the operation panel is lit or flashing.
•An error code appears in the display on the operation panel.
•KYOCERA Client Tool and Status Monitor will show the status of the machine.
If the Attention indicator is lit or flashing and an error code appears in the display on the operation panel, check the
KYOCERA Client Tool or Status Monitor.
Problems that can be resolved by the user are described below.
Note If the indicators light or flash repeatedly in manners not described above, a service error has probably
occurred. Switch off the power switch, unplug the power cord, and then plug the power cord back in and switch on
the power switch. This may clear the error. Even if the error is not cleared, contact your service representative.
Error Code Message displayed in
KYOCERA Client T ool
and Status Monitor* Meaning Remedy
C-F040 Error has occurred An error has occurred in the
machine. Turn the power OFF and then ON.
C-#### Error has occurred An error has occurred in the
machine. Make a note of the error code displayed
on the operation panel, and contact your
service representative.
(except C-F040)
E-0001 Non-genuine toner is
installed The installed toner container is
non-genuine. The manufacturer assumes no
responsibility for damage caused by a
non-genuine toner.
We recommend that you only use
genuine toner containers.
When you want to use the toner
container currently installed, press the
Mode Select key and [Stop/Reset]
simultaneously for 3 seconds or more.
E-0002 Error has occurred The installed toner container's
regional specification does not
match the machine’s.
Install the specified toner container.
E-0003 Memory full Scanning cannot be performed due
to insufficient memory of scanner. Only the scanned pages are available.
Press [Stop/Reset] and the job will be
canceled.
E-0004 Error has occurred The number of scanned pages
exceeds the maximum number. The maximum number of scanned
original pages is 99. Only the scanned
pages are available. Press [Stop/Reset]
and the job will be canceled.
E-0007 Add toner The toner has run out. Replace with a new toner container.
Error code E-0001
This is displayed in repeating
two-digit segments (E-, 00, and 01).
7-8
Troubleshooting
E-0008 Cover open The rear cover or front cover is
open.
Close the rear cover or front cover.
E-0009 Inner tray full The inner tray is full of paper. The machine pauses after 100 sheets are
printed. Remove paper from the inner
tray and press [Start] to resume printing.
E-0012 Memory overflow Unable to continue the job as the
memory is used up.
Change the print resolution from Fast
1200 to 600 dpi. Refer to Printer Driver
User Guide.
E-0014 Add paper The paper size in the paper source
is different from the printer driver or
KYOCERA Client Tool setting.
Load the proper size of paper in the
paper source.
E-0015 — The USB cable is not connected. Press [Stop/Reset] and connect the
USB cable.
The PC is powered off. Press [Stop/Reset] and turn the PC
power on.
Cannot find KYOCERA Client Tool. Press [Stop/Reset] and open KYOCERA
Client Tool.
—Not connected. The USB cable is not connected. Connect the USB cable.
The machine is powered off. Turn the machine power on.
Cannot find the appropriate driver. Install the appropriate driver.
E-0018 — The file does not exist in Print Box. Press [Stop/Reset].
E-0019 — The machine cannot run this
program due to unusable original
size is registered in the program.
Press [Stop/Reset] and change the
program settings.
J-0511 Paper jam A paper jam has occurred in the
rear cover.
Refer to Clearing Paper Jams on
page 7-9 and remove the jammed paper.
PF Add paper A paper jam has occurred in the
cassette.
Refer to Clearing Paper Jams on
page 7-9 and remove the jammed paper.
There is no paper in the paper
source.
Load paper into the paper source.
—Toner is running out. It is almost time to replace the
toner container.
Obtain a new toner container.
—Replacing the
Maintenance Kit
Replacement of the maintenance
kit is necessary at every 100,000
images of printing.
Replace Maintenance Kit.
* Events for which the Status Monitor provides notification can be set in the Configuration. Refer to Configuration
on page 2-36.
Error Code
Message displayed in
KYOCERA Client Tool
and Status Monitor*
Meaning Remedy
7-9
Troubleshooting
Clearing Paper Jams
If paper jams in the paper transport system, or no paper sheets are fed at all, the machine automatically goes offline, and
the Attention indicator will flash. KYOCERA Client Tool can indicate the location of the paper jam (the component where
the paper jam has occurred). Remove the paper jam. After removing the paper jam, the machine will resume printing.
Possible Paper Jam Locations
Detailed paper jam positions are as follows. Refer to the indicated page number to remove the paper jam.
General Considerations for Clearing Jams
Bear in mind the following considerations when attempting paper jam removal:
•If paper jams occur frequently, try using a different type of paper, replace the paper with paper from another ream, or
flip the paper stack over. The machine may have problems if paper jams recur after the paper is replaced.
•Whether or not the jammed pages are reproduced normally after printing is resumed, depends on the location of the
paper jam.
Paper Jam
Locations Error Code Message displayed in KYOCERA
Client Tool and Status Monitor Description Reference
page
AJ-0511 Paper jam A paper jam has occurred in the rear
cover.
7-10, 7-11
BPF*
*PF also appears when the paper has run out. In this case, add paper. Refer to Loading Paper
on page 2-4.
Add paper A paper jam has occurred in the
cassette.
7-12, 7-13
CAUTION When removing a paper jam, pull the paper gently so as not to tear it. Torn pieces of paper are
difficult to remove and may be easily overlooked, deterring the paper jam recovery.
A
B
7-10
Troubleshooting
Rear Cover
Follow the steps below to clear paper jams inside the rear cover.
Note When the front cover is opened or closed, the paper inside the
machine may be discharged.
1
3
1
2
2
IMPORTANT Take care not to
touch the drum and transfer
roller (black).
Drum
Transfer Roller
7-12
Troubleshooting
Cassette
Follow the steps below to clear paper jams in the cassette.
IMPORTANT Do not try to remove paper that has already been partially fed. Refer to Rear Cover on page 7-10.
Note Do not open or close the front cover or rear cover before removing the jammed paper.
1 2
3
54
Remove any partially fed paper.
Check to see if paper is loaded
correctly. If not, reload the paper.
Press [Start] to clear the error
and the machine warms up and
resumes printing.
7-13
Troubleshooting
If paper feed failure occurs
Check on and reduction of number of paper sheets loaded
If an excessive amount of thick paper is loaded in the cassette, it may not be fed. In that case,
reduce the number of sheets to be loaded.
Edge fanning and curl straightening
Remove all the even pages (including the instruction sheet) from the inner tray, fan through the
sheets to separate them prior to loading.
If the paper is curled at an edge, straighten it prior to reloading.
No paper feed due to wavy paper edge
When the paper feed fails because the edge of the paper is wavy, turn it upside down and load
it again.
7-14
Troubleshooting
8-2
Appendix
Specifications
Common Functions
Note These specifications are subject to change without notice.
Item Description
Type Desktop
Printing Method Electrophotography by semiconductor laser
Paper Weight 60 to 220 g/m²
Paper Type Plain, Preprinted, Labels, Bond, Recycled, Vellum, Rough, Letterhead,
Color, Prepunched, Envelope, Cardstock, Thick paper, High Quality,
Custom 1 to 8
Warm-up Time
(22°C/71.6°F, 60%RH)
Power on 20 seconds or less
Sleep 12 seconds or less
Paper Capacity 250 sheets (80 g/m²)
Inner Tray Capacity Standard paper 100 sheets (80 g/m²) (The machine pauses after 100 sheets are printed.)
Special paper 1 sheet
Continuous Copying 1 to 99 sheets
Image Write System Semiconductor laser and electrophotography
Memory ROM: 32 MB, RAM: 64 MB
Interface USB Interface Connector: 1 (Hi-Speed USB)
Operating Environment Temperature 10 to 32.5°C/50 to 90.5°F
Humidity 15 to 80%
Altitude 3,500 m/11,482.8 ft maximum
Brightness 1,500 lux maximum
Dimension (W × D × H) 390 × 333 × 317 mm
15-3/8 × 13-1/8 × 12-1/2"
Weight (with toner container) 8.7 kg/19.14 lb
Space Required (W × D) 390 × 645 mm
15-3/8 × 25-3/8"
Power Requirements 230 V Specification Model: 220 to 240 V (50 Hz/60 Hz, 3.1 A)
120 V Specification Model:120 V (60 Hz, 6.0 A)
8-3
Appendix
Copy Functions
Item Description
Paper Size A4, A5, A6, Folio, JIS B5, ISO B5, Letter, Legal, Statement, Executive,
Oficio II (216 × 340 mm, 8-1/2 × 13 inches), 216 × 340 mm, 16 K,
Custom (70 × 148 to 216 × 356 mm, 2-3/4 × 5-13/16 to
8-1/2 × 14 inches)
Copying Speed
(300 × 300 dpi)
A4 Light (63 g/m² or less): 20 images/min
Normal 1 (64 to 69 g/m²): 20 images/min
Normal 2 (3) (70 to 105 g/m²): 20 images/min
A4 (Quiet Mode) Light (63 g/m² or less): 15 images/min
Normal 1 (64 to 69 g/m²): 15 images/min
Normal 2 (3) (70 to 105 g/m²): 15 images/min
Heavy 1 (106 to 135 g/m²): 14 images/min
Heavy 2 (3) (136 to 220 g/m²): 13 images/min
Letter Light (63 g/m² or less): 21 images/min
Normal 1 (64 to 69 g/m²): 21 images/min
Normal 2 (3) (70 to 105 g/m²): 21 images/min
Letter (Quiet Mode) Light (63 g/m² or less): 16 images/min
Normal 1 (64 to 69 g/m²): 16 images/min
Normal 2 (3) (70 to 105 g/m²): 16 images/min
Heavy 1 (106 to 135 g/m²): 14 images/min
Heavy 2 (3) (136 to 220 g/m²):13 images/min
A5/B5/A6 (Quiet Mode) Light (63 g/m² or less): 12 images/min
Normal 1 (64 to 69 g/m²): 12 images/min
Normal 2 (3) (70 to 105 g/m²): 12 images/min
Heavy 1 (106 to 135 g/m²): 10 images/min
Heavy 2 (3) (136 to 220 g/m²): 9 images/min
A5/B5/A6 (from 11th
image)
(Quiet Mode)
Light (63 g/m² or less): 10 images/min
Normal 1 (64 to 69 g/m²): 10 images/min
Normal 2 (3) (70 to 105 g/m²): 10 images/min
Heavy 1 (106 to 135 g/m²): 8 images/min
Heavy 2 (3) (136 to 220 g/m²): 8 images/min
First Print Time (A4, feed from cassette) 12 seconds or less
Zoom Level 25 to 400%, 1% increments
Resolution 600 × 600 dpi
Supported Original Types Sheet, Book, 3-dimensional objects (maximum original size: A4/Letter)
Original Feed System Fixed
8-4
Appendix
Printer Functions
Item Description
Paper Size A4, A5, A6, Folio, JIS B5, ISO B5, Letter, Legal, Statement, Executive,
Envelope Monarch, Envelope #10, Envelope #9, Envelope #6-3/4,
Envelope C5, Envelope DL, Oficio II (216 × 340 mm, 8-1/2 × 13 inches),
216 × 340 mm, 16 K, Custom (70 × 148 to 216 × 356 mm,
2-3/4 × 5-13/16 to 8-1/2 × 14 inches)
Printing Speed A4 Light (63 g/m² or less): 20 images/min
Normal 1 (64 to 69 g/m²): 20 images/min
Normal 2 (3) (70 to 105 g/m²): 20 images/min
A4 (Quiet Mode) Light (63 g/m² or less): 15 images/min
Normal 1 (64 to 69 g/m²): 15 images/min
Normal 2 (3) (70 to 105 g/m²): 15 images/min
Heavy 1 (106 to 135 g/m²): 14 images/min
Heavy 2 (3) (136 to 220 g/m²): 13 images/min
Letter Light (63 g/m² or less): 21 images/min
Normal 1 (64 to 69 g/m²): 21 images/min
Normal 2 (3) (70 to 105 g/m²): 21 images/min
Letter (Quiet Mode) Light (63 g/m² or less): 16 images/min
Normal 1 (64 to 69 g/m²): 16 images/min
Normal 2 (3) (70 to 105 g/m²): 16 images/min
Heavy 1 (106 to 135 g/m²): 14 images/min
Heavy 2 (3) (136 to 220 g/m²):13 images/min
A5/B5/A6 (Quiet Mode) Light (63 g/m² or less): 12 images/min
Normal 1 (64 to 69 g/m²): 12 images/min
Normal 2 (3) (70 to 105 g/m²): 12 images/min
Heavy 1 (106 to 135 g/m²): 10 images/min
Heavy 2 (3) (136 to 220 g/m²): 9 images/min
A5/B5/A6 (from 11th
image)
(Quiet Mode)
Light (63 g/m² or less): 10 images/min
Normal 1 (64 to 69 g/m²): 10 images/min
Normal 2 (3) (70 to 105 g/m²): 10 images/min
Heavy 1 (106 to 135 g/m²): 8 images/min
Heavy 2 (3) (136 to 220 g/m²): 8 images/min
Legal Light (63 g/m² or less): 13 images/min
Normal 1 (64 to 69 g/m²): 13 images/min
Normal 2 (3) (70 to 105 g/m²): 13 images/min
Legal (Quiet Mode) Light (63 g/m² or less): 12 images/min
Normal 1 (64 to 69 g/m²): 12 images/min
Normal 2 (3) (70 to 105 g/m²): 12 images/min
Heavy 1 (106 to 135 g/m²): 11 images/min
Heavy 2 (3) (136 to 220 g/m²): 10 images/min
First Print Time (A4, feed from Cassette) 8.5 seconds or less
Resolution 600 × 600 dpi/Fast 1200 dpi
Controller ARM926EJ 390MHz
Supported OS Windows XP, Windows Server 2003/R2, Windows Vista, Windows 7,
Windows Server 2008/R2, Mac OS X 10.5 or higher
8-5
Appendix
Scanner Functions
Item Description
System Requirements CPU: 20 MHz
RAM: 64 MB
Resolution 200 × 200 dpi, 300 × 300 dpi, 400 × 400 dpi, 600 × 600 dpi
File Format BMP, JPEG, PNG, TIFF, PDF
Transmission System PC transmission: Scan to Folder
TWAIN scan*
WIA scan**
* Available Operating System: Windows XP, Windows Server 2003/R2, Windows Vista, Windows 7, Windows
Server 2008/R2
** Available Operating System: Windows Vista, Windows 7, Windows Server 2008/R2
8-6
Appendix
Index-1
Index
A
Adhesive label ................................................................ 2-8
Attention Indicator
operation panel ........................................................ 1-4
C
Cassette
basis weight ............................................................ 2-6
clearing paper jams ............................................... 7-12
components ............................................................. 1-2
loading paper ......................................................... 2-12
paper sizes .............................................................. 2-5
paper type ............................................................. 2-11
Cassette cover ............................................................. 2-15
components ............................................................. 1-2
Cleaning
interior of the machine ............................................. 6-5
original cover, platen ............................................... 6-5
Clearing paper jams ....................................................... 7-9
cassette ................................................................. 7-12
possible paper jam locations ................................... 7-9
rear cover section .................................................. 7-10
Colored paper ............................................................... 2-10
Components
at the front of the machine ...................................... 1-2
at the rear of the machine ....................................... 1-3
Configuration ................................................................ 2-36
Copy tab ................................................................ 2-40
Device Defaults tab ............................................... 2-38
Status Monitor tab ................................................. 2-41
Connection
power cord .............................................................. 2-2
USB cable ............................................................... 2-2
Copies indicator
operation panel ........................................................ 1-4
Copying .......................................................................... 3-1
basic operation ........................................................ 3-2
functions .................................................................. 3-5
ID Card Copy .......................................................... 3-6
manual duplex ......................................................... 3-3
programs ................................................................. 3-5
Copy key
operation panel ........................................................ 1-4
D
Default settings ............................................................. 2-28
Density indicator
operation panel ........................................................ 1-4
E
Energy Star ........................................................................ vi
Envelopes ....................................................................... 2-9
Error messages .............................................................. 7-7
F
Front cover
components ............................................................. 1-2
I
ID Card Copy .................................................................. 3-6
ID Card Copy key
operation panel ........................................................ 1-4
Indicator
Attention .................................................................. 1-4
Copies ..................................................................... 1-4
Density ..................................................................... 1-4
Processing ............................................................... 1-4
Program ................................................................... 1-4
Inner tray
components ............................................................. 1-2
Install the software
Macintosh .............................................................. 2-19
Windows ................................................................ 2-18
Instruction sheet
manual duplex ......................................................... 4-4
K
Key
Copy ........................................................................ 1-4
ID Card Copy ........................................................... 1-4
Mode Select ............................................................. 1-4
Print Box .................................................................. 1-4
Quiet Mode .............................................................. 1-4
Scan ........................................................................ 1-4
Start ......................................................................... 1-4
Stop/Reset ............................................................... 1-4
KYOCERA Client Tool .................................................. 2-22
L
Label ............................................................................... 2-8
Loading originals ........................................................... 2-16
Loading paper
cassette ................................................................. 2-12
M
Machine parts ................................................................. 1-1
Maintenance ................................................................... 6-1
cleaning ................................................................... 6-5
maintenance kit replacement ................................... 6-5
maintenance menu .................................................. 6-7
toner container replacement .................................... 6-2
Maintenance kit
replacement ............................................................. 6-5
Maintenance menu ......................................................... 6-7
Manual duplex
copying .................................................................... 3-3
Index-2
printing .................................................................... 4-3
Mode Select key
operation panel ........................................................ 1-4
Moving machine ............................................................. 6-8
O
Operation panel
components ............................................................. 1-2
indicators, keys, overview ....................................... 1-4
Original cover
cleaning ................................................................... 6-5
components ............................................................. 1-2
Original size indicator plates
components ............................................................. 1-2
P
Paper
minimum and maximum sizes ................................. 2-5
Paper length guide ....................................................... 2-13
Paper stopper ............................................................... 2-12
components ............................................................. 1-2
Paper weight .................................................................. 2-6
Paper width guide ......................................................... 2-12
Platen
cleaning ................................................................... 6-5
components ............................................................. 1-2
Postcards ....................................................................... 2-9
Power cord
connection ............................................................... 2-2
Power cord connector
components ............................................................. 1-3
Power switch
components ............................................................. 1-2
Preparation ..................................................................... 2-1
Preparing paper ............................................................ 2-11
Preprinted paper ........................................................... 2-10
Preset Tool ................................................................... 2-28
Print Box ......................................................................... 4-5
printing .................................................................... 4-6
saving ...................................................................... 4-5
Print Box key
operation panel ........................................................ 1-4
Printing ........................................................................... 4-1
manual duplex ......................................................... 4-3
printer driver ............................................................ 4-2
printing from Application Software ........................... 4-2
Processing Indicator
operation panel ........................................................ 1-4
Program indicator
operation panel ........................................................ 1-4
Programs
copying .................................................................... 3-5
registering ............................................................. 2-28
scanning .................................................................. 5-3
Prolonged non-use ......................................................... 6-8
Push Scan ...................................................................... 5-2
Q
Quick Scan
settings .................................................................. 2-34
using ........................................................................ 5-4
Quiet Mode ..................................................................... 1-4
Quiet Mode key
operation panel ........................................................ 1-4
R
Rear cover
components ............................................................. 1-3
Rear cover section
clearing paper jams ............................................... 7-10
Recycled paper ............................................................. 2-10
Replacement
maintenance kit ....................................................... 6-5
toner container ......................................................... 6-2
S
Scan key
operation panel ........................................................ 1-4
Scanning ......................................................................... 5-1
programs ................................................................. 5-3
Push Scan ............................................................... 5-2
Quick Scan .............................................................. 5-4
TWAIN/WIA ............................................................. 5-5
Software ........................................................................ 2-17
Solving malfunctions ....................................................... 7-2
Special paper .................................................................. 2-8
Specifications .................................................................. 8-2
common functions ................................................... 8-2
copy ......................................................................... 8-3
printer ...................................................................... 8-4
scanner .................................................................... 8-5
Start key
operation panel ........................................................ 1-4
Status Monitor ............................................................... 2-27
Status page
printing ........................................................... 1-4, 2-42
Stop/Reset key
operation panel ........................................................ 1-4
T
Thick paper ................................................................... 2-10
Tips ................................................................................. 7-6
Toner container
how to replace ......................................................... 6-3
replacement ............................................................. 6-2
Toner kit
toner container, plastic waste bag, installation guide 6-2
Troubleshooting .............................................................. 7-1
clearing paper jams ................................................. 7-9
error messages ........................................................ 7-7
solving malfunctions ................................................ 7-2
Turning on the power ...................................................... 2-3
TWAIN/WIA .................................................................... 5-5
Index-4
KYOCERA Document Solutions Austria GmbH
Eduard-Kittenberger-Gasse 95, 1230 Vienna,
Austria
Phone: +43-1-863380
Fax: +43-1-86338-400
KYOCERA Document Solutions Nordic AB
Esbogatan 16B 164 75 Kista,
Sweden
Phone: +46-8-546-550-00
Fax: +46-8-546-550-10
KYOCERA Document Solutions Norge NUF
Postboks 150 Oppsal, 0619 Oslo,
Norway
Phone: +47-22-62-73-00
Fax: +47-22-62-72-00
KYOCERA Document Solutions Danmark A/S
Ejby Industrivej 60, DK-2600 Glostrup,
Denmark
Phone: +45-70223880
Fax: +45-45765850
KYOCERA Document Solutions Portugal Lda.
Rua do Centro Cultural, 41 (Alvalade) 1700-106 Lisboa,
Portugal
Phone: +351-21-843-6780
Fax: +351-21-849-3312
KYOCERA Document Solutions
South Africa (Pty) Ltd.
49 Kyalami Boulevard,
Kyalami Business Park 1685 Midrand, South Africa
Phone: +27-11-540-2600
Fax: +27-11-466-3050
KYOCERA Document Solutions Russia LLC
Botanichesky pereulok 5, Moscow, 129090,
Russia
Phone: +7(495)741-0004
Fax: +7(495)741-0018
KYOCERA Document Solutions Middle East
Dubai Internet City, Bldg. 17,
Office 157 P.O. Box 500817, Dubai,
United Arab Emirates
Phone: +971-04-433-0412
KYOCERA Document Solutions Inc.
2-28, 1-chome, Tamatsukuri, Chuo-ku
Osaka 540-8585, Japan
Phone: +81-6-6764-3555
http://www.kyoceradocumentsolutions.com
KYOCERA Document Solutions Europe B.V.
Bloemlaan 4, 2132 NP Hoofddorp,
The Netherlands
Phone: +31-20-654-0000
Fax: +31-20-653-1256
KYOCERA Document Solutions Nederland B.V.
Beechavenue 25, 1119 RA Schiphol-Rijk,
The Netherlands
Phone: +31-20-5877200
Fax: +31-20-5877260
KYOCERA Document Solutions (U.K.) Limited
8 Beacontree Plaza,
Gillette Way Reading, Berkshire RG2 0BS,
United Kingdom
Phone: +44-118-931-1500
Fax: +44-118-931-1108
KYOCERA Document Solutions Italia S.p.A.
Via Verdi, 89/91 20063 Cernusco s/N.(MI),
Italy
Phone: +39-02-921791
Fax: +39-02-92179-600
KYOCERA Document Solutions Belgium N.V.
Sint-Martinusweg 199-201 1930 Zaventem,
Belgium
Phone: +32-2-7209270
Fax: +32-2-7208748
KYOCERA Document Solutions France S.A.S.
Espace Technologique de St Aubin
Route de I’Orme 91195 Gif-sur-Yvette CEDEX,
France
Phone: +33-1-69852600
Fax: +33-1-69853409
KYOCERA Document Solutions Espana, S.A.
Edificio Kyocera, Avda. de Manacor No.2,
28290 Las Matas (Madrid), Spain
Phone: +34-91-6318392
Fax: +34-91-6318219
KYOCERA Document Solutions Finland Oy
Atomitie 5C, 00370 Helsinki,
Finland
Phone: +358-9-47805200
Fax: +358-9-47805390
KYOCERA Document Solutions
Europe B.V., Amsterdam (NL) Zürich Branch
Hohlstrasse 614, 8048 Zürich,
Switzerland
Phone: +41-44-9084949
Fax: +41-44-9084950
KYOCERA Document Solutions
Deutschland GmbH
Otto-Hahn-Strasse 12, 40670 Meerbusch,
Germany
Phone: +49-2159-9180
Fax: +49-2159-918100
First Edition 2012.09
2M4KMEN000