Table of Contents
- Contents
- Legal and Safety Information
- Notice
- Regarding Tradenames
- Compliance and Conformity
- Safety Instructions Regarding the Disconnection of Power
- Energy Saving Control Function
- Duplex Printing (FS-1025MFP, FS-1125MFP and FS-1325MFP)
- Resource Saving - Paper
- Environmental benefits of "Power Management"
- Energy Star (ENERGY STAR®)
- Legal Restriction on Copying/Scanning
- FCC PART 68 REQUIREMENTS
- IMPORTANT SAFETY INSTRUCTIONS
- IMPORTANTES MESURES DE SECURITE
- Declarations to European Directives
- Safety Conventions in This Guide
- Environment
- Cautions when Handling Consumables
- About the Operation Guide
- Conventions in This Guide
- 1 Machine Parts
- 2 Preparation
- 3 Copying
- 4 Printing
- 5 Scanning
- 6 Default Setting (System Menu)
- 7 FAX Operations
- 8 Maintenance
- 9 Troubleshooting
- 10 Appendix
- Index
KYOCERA FS-1320MFP User Manual
Displayed below is the user manual for FS-1320MFP by KYOCERA which is a product in the Multifunctionals category. This manual has pages.
Related Manuals
FS-1025MFP
FS-1120MFP/FS-1125MFP
FS-1320MFP/FS-1325MFP
oPeratioN guide
This Operation Guide is for models FS-1025MFP, FS-1120MFP, FS-1125MFP, FS-1320MFP and FS-1325MFP.
This Operation Guide is intended to help you operate the machine correctly, perform routine maintenance and take a
simple troubleshooting action as necessary, so that you can always use the machine in good condition.
We recommend the use of our own brand supplies. We will not be liable for any damage caused by the use of third party
supplies in this machine.
A label shown in the illustration assures that the supplies are our own brand.
Included Guides
The following guides are supplied with the machine. Refer to them as necessary.
Product Library disc
Quick Installation Guide Describes the procedures for installation of the machine.
Safety Guide Provides safety and cautionary information for the installation and use of
the machine. Be sure to read this guide before using the machine.
Safety Guide
(FS-1020MFP/FS-1025MFP/FS-1120MFP/
FS-1125MFP/FS-1220MFP/FS-1320MFP/
FS-1325MFP)
Describes the machine installation space, cautionary space, and other
information. Be sure to read this guide before using the machine.
Operation Guide (This Guide) Describes how to load paper, basic copy, print and scan operations, and
troubleshooting.
KYOCERA Client Tool User Guide Describes how to use KYOCERA Client Tool. KYOCERA Client Tool is a
software program that is installed on your computer to enable you to
configure machine settings.
Printer Driver User Guide Describes how to install the printer driver and use printer functionality.
KYOCERA Net Viewer User Guide Describes how to monitor the network printing system with KYOCERA Net
Viewer.
FAX Driver User Guide Describes how to install and use the FAX Driver in order to use FAX Driver
functionality.
i
Contents
1 Machine Parts ................................................................................................................................................1-1
Front Machine Components .........................................................................................................................1-2
Rear Machine Components ..........................................................................................................................1-3
Operation Panel ................ .... ... ... ... .... ... ................ ... ... .... ... ... ... ................. ... ... ... ... .... ... ..................................1-4
2 Preparation ........ ............. ............. ............. ............. ............. ............. .......... ............ .........................................2-1
Connections ...................................................................................................................................................2-2
Loading Paper ....... ................ ... ... ... .... ... ... ................ ... .... ... ... ... .... ................ ... ... ... .... ... ..................................2-5
Loading Originals ........................................................................................................................................2-18
Installing and Uninstalling Drivers and Utilities ...... .... ... ... ................ .... ... ... ... ... .... ................ ... ... .............2-20
Machine Settings .........................................................................................................................................2-26
Configuration ...............................................................................................................................................2-48
Printing the Status Page .............................................................................................................................2-58
3 Copying ..........................................................................................................................................................3-1
Basic Operation .............................................................................................................................................3-2
Manual Duplex .................. .... ... ... ... ................. ... ... ... ... .... ... ................ ... .... ... ... ... ... .........................................3-3
Using Programs ............. ... .... ... ................ ... .... ... ... ... ... ................. ... ... ... .... ... ... ................ ...............................3-5
Copying Functions ........................................................................................................................................3-6
ID Card Copy ................................................................................................................................................3-13
4 Printing ...........................................................................................................................................................4-1
Printing from Application Software .............................................................................................................4-2
About GX Driver .............................................................................................................................................4-2
Manual Feed (FS-1025MFP, FS-1125MFP and FS-1325MFP) .....................................................................4-3
Manual Duplex (FS-1120MFP and FS-1320MFP only) ................................................................................4-4
Print Box .........................................................................................................................................................4-6
Changing the Default Printer Driver Settings (Windows 7 for example) ..................................................4-8
5 Scanning ........................................................................................................................................................5-1
Push Scan ......................................................................................................................................................5-2
Using Programs ............. ... .... ... ................ ... .... ... ... ... ... ................. ... ... ... .... ... ... ................ ...............................5-3
Quick Scan (Scan to PDF/Scan to Email/Scan to Folder) ..........................................................................5-4
Scanning using TWAIN/WIA ......... .... ... ... ... .... ... ................ ... ... .... ... ... ... ................ .... ... ... ... .... ... .....................5-5
6 Default Setting (System Menu) .....................................................................................................................6-1
Default Setting (System Menu) .....................................................................................................................6-2
System Menu Settings ..................................................................................................................................6-3
Administrator ID ............................................................................................................................................6-6
7 FAX Operations .............................................................................................................................................7-1
Before Using the Fax Machine .....................................................................................................................7-2
Entering the Destination ...............................................................................................................................7-7
Sending Faxes .............................................................................................................................................7-12
Receiving Faxes ..........................................................................................................................................7-21
Printing Communication Reports ..............................................................................................................7-23
Fax Settings .................................................................................................................................................7-24
Sending Faxes from PC ..............................................................................................................................7-37
8 Maintenance ...................................................................................................................................................8-1
General Information ......................................................................................................................................8-2
Toner Container Replacement .................. .... ... ... ................ ... .... ... ... ... .... ................ ... ... ... .... ... .....................8-2
Maintenance Kit Replacement ......................................................................................................................8-5
ii
Cleaning the Machine ................................................................................................................................... 8-5
Maintenance Menu .......... .... ... ... ....... ... ... ... .... ... ............................................................................................. 8-8
Prolonged Non-Use and Moving of the Machine ....................................................................................... 8-9
9 Troubleshooting ........ ....................... ...................... ....................... ...................... .......................................... 9-1
Solving Malfunctions .................................................................................................................................... 9-2
Error Messages ............................................................................................................................................. 9-8
FAX Error Code List .................................................................................................................................... 9-12
Clearing Paper Jams .................................................................................................................................. 9-14
10 Appendix ....... ....................... ...................... ....................... ....................... .................................................... 10-1
Character Entry Method ............................................................................................................................. 10-2
Specifications ...... ................... ................ ................... .................... ................... ........................................... 10-5
Index ...............................................................................................................................................................Index-1
iii
Legal and Safety Information
Notice
The information in this guide is subject to change without notification. Additional pages may be inserted in future editions.
The user is asked to excuse any technical inaccuracies or typographical errors in the present edition.
No responsibility is assumed if accidents occur while the user is following the instructions in this guide. No responsibility is
assumed for defects in the machine's firmware (contents of its read-only memory).
This guide, and any copyrightable subject matter sold or provided with or in connection with the sale of the machine, are
protected by copyright. All rights are reserved. Copying or other reproduction of all or part of this guide, or any
copyrightable subject matter without the prior written consent of KYOCERA Document Solutions Inc. is prohibited. Any
copies made of all or part of this guide, or any copyright able subject must contain the same copyright notice as the material
from which the copying is done.
Regarding Tradenames
Adobe Acrobat, and Flash are registered trademarks of Adobe Systems Incorporated.
Macintosh and Mac OS are trademarks of Apple Inc., registered in the U.S. and other countries.
Microsoft, MS-DOS, and Windows are registered trademarks of Microsof t Corporation in the U.S.A. and/or other countries.
ENERGY STAR is a U.S. registered mark.
All other brand and product names are registered trademarks or trademarks of their respective companies.
CAUTION NO LIABILITY IS ASSUMED FOR ANY DAMAGE CAUSED BY IMPROPER INSTALLATION.
iv
Compliance and Conformity
This equipment has been tested and found to comply with the limit s f or a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However , there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment of f and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
• The use of a non-shielded interface cable with the referenced device is prohibited.
CAUTION — The changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
This device complies with Part 15 of FCC Rules.
Operation is subject to the following two conditions; (1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause undesired operation of the device.
* The above warning is valid only in the United States of America.
Interface connectors
IMPORTANT Be sure to power off the machine before connecting or disconnecting an interface cable. For protection
against static electricity discha rge to the machine's internal electronics throug h the interface connector(s), cover any
interface connector that is not in use with the protective cap supplied.
CDRH Regulations
The Center for Devices and Radiological Health (CDRH) of the U.S. Food and Drug Administration implemented
regulations for laser products on August 2, 1976. These regulations apply to laser products manufactured after August 1,
1976. Compliance is mandatory for products marketed in the United States. A label indicating compliance with the CDRH
regulations must be attached to laser products marketed in the United States.
Canadian Department of Co mmunications Compliance Statement
This Class B digital apparatus complies with Canadian ICES-003.
Avis de conformité aux normes du ministère des Communications du Canada
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Note Use shielded interface cables.
v
Safety Instructions Regarding the Disconnection of Power
Caution: The power plug is the main isolation device! Other switches on the equipment are only functional switches and
are not suitable for isolating the equipment from the power source.
VORSICHT: Der Netzstecker ist die Hauptisoliervorrichtung! Die anderen Schalter auf dem Gerät sind nur
Funktionsschalter und können nicht verwendet werden, um den Stromfluß im Gerät zu unterbrechen.
Energy Saving Control Function
To reduce energy consumption while in a waiting state, the device comes equipped with an energy saving control function
for switching to Sleep Mode as well as Power Off Mode where power consumption is automatically reduced to a
minimum after a certain amount of time elapses since the device was last used.
Sleep Mode
The device automatically enters Sleep Mode when approximately 1 minute has passed since the device was last used.
The amount of time of no activity that must pass before Sleep Mode is activated may be lengthened by changing the Auto
sleep setting. For details, refer to Device Defaults Tab on page 2-50.
Power Of f Mo d e
The device automatically turns its power off when 1 hour has passed since the device was last used. The amount of time
of no activity that must pass before Power Off Mode is activated may be lengthened by changing the Power Off Timer
setting. For details, refer to Device Defaults Tab on page 2-50.
In case of not using the machine for an extended period of time
CAUTION Remove paper from the cassettes an d seal it in the paper storage bag to protect it from humidity.
Duplex Printing (FS-1025MFP, FS-1125MFP and FS-1325MFP)
This machine includes duplex printing as a standard function. For example, by printing two single-sided originals onto a
single sheet of paper as a duplex printing, it is possible to lower the amount of paper used.
Printing in duplex mode reduces paper consumption and contributes to the conservation of forest resources. Duplex mode
also reduces the amount of paper that must be purchased, and thereby reduces cost. It is recommended that machines
capable of duplex printing be set to use duplex mode by default.
Resource Saving - Paper
For the preservation and sustainable use of forest resources, it is recommended that recycled as well as virgin paper
certified under environmental stewardship initiatives or carrying recognised ecolabels, which meet EN 12281:2002*1 or an
equivalent quality standard, be used.
This machine also supports printing on 64 g/m² paper. Using such paper containing less raw materials can lead to further
saving of forest resources.
*1: EN12281:2002 "Printing and business paper - Requirements for copy paper for dry toner imaging processes"
Your sales or service representative can provide information about recommended paper types.
CAUTION If this machine will be left unused for an extended period (e.g. overnight), turn it off at the power
switch. If the machine will not be used for an even longer period of time (e.g. vacation), remove the power
plug from the outlet as a safe ty precau tion. If the optio nal Fax kit is installed, note that turning the mach ine
off at the main power switch disables fax transmission and reception.
vi
Environmental benefits of "Power Management"
To reduce power consumption when idle, this machine is equipped with a power management function that automatically
activates energy-saving mode when the machine is idle for a certain period of time. Although it takes the machine a slight
amount of time to return to READY mode when in energy-saving mode, a significant reduction in energy consumption is
possible.
It is recommended that the machine be used with the activation time for energy-saving mode set to the default setting.
Energy Star (ENERGY S TAR®)
We have determined as a company participating in ENERGY STAR® that this product has earned the
ENERGY STAR®.
ENERGY STAR® is a voluntary energy ef ficiency program with the goal of developing and promoting the
use of products with high energy efficiency in order to help prevent global warming. By purchasing
ENERGY STAR® qualified products, customers can help reduce emissions of greenhouse gases during
product use and cut energy-related costs.
Legal Restriction on Copying/Scanning
It may be prohibited to copy/scan copyrighted material without permission of the copyright owner.
Copying/Scanning the following items is prohibited and may be penalized by law. It may not be limited to these items. Do
not knowingly copy/scan the items that are not to be copied/scanned.
•Paper money
•Bank note
•Securities
•Stamp
•Passport
•Certificate
Local laws and regulations may prohibit or restrict copying/scanning of other items not mentioned above.
vii
FCC PART 68 REQUIREMENTS
1This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the rear side
of the equipment to install Assembly Board is a label that contains, among other information, a product identifier in the
format US:AAAEQ##TXXXX. If requested, this number must be provided to the telephone company.
2This equipment connects to the network via USOC RJ11C.
3A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the
applicable FCC Part 68 rules and requirement s adopted by the ACTA. A compliant telephone cord and modular plug is
provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. See
installation instructions for details.
4The REN is used to determine the number of devices that may be connected to a telephon e line. Excessive RENs on
a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the
sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as
determined by the total RENs, contact the local telephone company. For products approved after July 23, 2001, the
REN for this product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented
by ## are the REN without a decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separately
shown on the label.
5If this equipment causes harm to the telephone network, the telephone company will notify you in advance that
temporary discontinuance of service may be required. But if advance notice isn't practical, the telephone comp any will
notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you
believe it is necessary.
6The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the
operation of the equipment. If this happens the telephone company will provide advance notice in order for you to
make necessary modifications to maintain uninterrupted service.
7If trouble is experienced with this equipment, please contact the following company for repair and (or) warranty
information:
If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect
the equipment until the problem is resolved.
8This equipment cannot be used on public coin service provided by the telephone company. Connection to Party line
service is subject to state tarif fs. Contact the state public utility commission, public service commission or corporation
commission for information.
9If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this
equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment,
consult your telephone company or a qualified installer.
10 The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other
electronic device, including F AX machines, to send any message unless such message clearly cont ains in a margin at
the top or bottom of each transmitted page or on the first page of the transmission, the date and time it is sent and an
identification of the business or other entity, or other individual sending the message and the telephone number of the
sending machine or such business, other entity, or individual. (The telephone number provided may not be a 900
number or any other number for which charges exceed local or long-distance transmission charges.)
In order to program this information into your FAX machine, you should complete the following steps: (Insure that it will
be transmitted, see Local FAX Name on page 7-3, Local FAX Number on page 7-4, TTI (Transmit Terminal
Identification) on page 7-3 and Setting Date and Time on page 7-2.)
KYOCERA Document Solutions America, Inc.
225 Sand Road,
Fairfield, New Jersey 07004-0008, USA
Phone: +1-973-808-8444
Fax: +1-973-882-6000
viii
IMPORTANT SAFETY INSTRUCTIONS
When using your telephone equip ment, basic safety precautions should always be followed to reduce the risk of fire,
electric shock and injury to persons, including the following:
CAUTION: To reduce the risk of fire, use only No.26 AWG or larger UL listed or CSA certified telecommunication line
cord.
1Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet
basement or near a swimming pool.
2Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric
shock from lightning.
3Do not use the telephone to report a gas leak in the vicinity of the leak.
4Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may
explode. Check with local codes for possible special disposal instructions.
SAVE THESE INSTRUCTIONS
IMPORTANTES MESURES DE SECURITE
Certaines mesures de sécurité doivent être prises pendant l'utilisation de matériel téléphonique afin de réduire les
risques d'ince nd ie, de choc éle ct riq ue et de blessures. En voici quelques unes:
1Ne pas utiliser l'app areil près de l'eau, p. ex., près d'une baignoire, d'un lavabo, d'un évier de cuisine, d'un bac à laver,
dans un sous-sol humide ou près d'une piscine.
2Eviter d'utiliser le téléphone (sauf s'il s'agit d'un appareil sans fil) pendant un orage électrique. Ceci peut présenter un
risque de choc électrique causé par la foudre.
3Ne pas utiliser l'appareil téléphonique pour signaler une fuite de gaz s'il est situé près de la fuite.
4Utiliser seulement le cordon d'alimentation et le type de piles indiqués dans ce manuel. Ne pas jeter les piles dans le
feu: elles peuvent exploser. Se conformer aux règlements pertinents quant à l'élimination des piles.
CONSERVER CES INSTRUCTIONS
ix
Declarations to European Directives
DECLARATION OF CONFORMITY TO 2004/108/EC, 2006/95/EEC, 93/68/EEC, 1999/5/EC and 2009/125/EC
We declare under our sole responsibility that the product to which this declaration relates is in conformity with the following
specifications.
Limits and methods of measurement for immunity
characteristics of information technology equipment EN55024
Limits and methods of measurement for radio
interference characteristics of information technology
equipment
EN55022 Class B
Limits for harmonic currents emissions for equipment
input current 16A per phase EN61000-3-2
Limitation of voltage fluctuations and flicker in
low-voltage supply systems for equipment with rated
current 16A
EN61000-3-3
Safety of information technology equipment, including
electrical business equipment EN60950-1
Terminal Equipment (TE);
Attachment requirements for pan-European approval
for connection to the analogue Public Switched
Telephone Networks (PSTNs) of TE (excluding TE
supporting the voice telephony service) in which
network addressing, if provided, is by means of Dual
Tone Multi Frequency (DTMF) signalling
TBR 21
x
Safety Conventions in This Guide
The sections of this guide and parts of the machine marked with symbols are safety warnings meant to protect the user,
other individuals and surrounding objects, and ensure correct and safe usage of the machine. The symbols and their
meanings are indicated below.
The following symbols indicate that the related section includes safety warnings. Specific points of attention are indicated
inside the symbol.
The following symbols indicate that the related section includes information on prohibited actions. Specifics of the
prohibited action are indicated inside the symbol.
The following symbols indicate that the related section includes information on actions which must be performed. Specifics
of the required action are indicated inside the symbol.
Please contact your service representative to order a replacement if the safety warnings in this Operation Guide are
illegible or if the guide itself is missing. (fee required)
WARNING: Indicates that serious injury or even death may result from insufficient attention to or incorrect
compliance with the related points.
CAUTION: Indicates that personal injury or mechanical damage may result from insufficient attention to or
incorrect compliance with the related points.
.... [General warning]
.... [Warning of high temperature]
.... [Warning of prohibited action]
.... [Disassembly prohibited]
.... [Alert of required action]
.... [Remove the power plug from the outlet]
.... [Always connect the machine to an outlet with a ground connection]
Note An original which resembles a bank note closely may not be copied properly in some rare cases because this
machine is equipped with a counterfeiting prevention function.
xi
Environment
The service environmental conditions are as follows:
•Temperature: 50 to 90.5 °F (10 to 32.5 °C)
•Humidity: 15 to 80 %
However, adverse environmental conditions may affect the image quality. Avoid the following locations when selecting a
site for the machine.
•Avoid locations near a window or with exposure to direct sunlight.
•Avoid locations with vibrations.
•Avoid locations with drastic temperature fluctuations.
•Avoid locations with direct exposure to hot or cold air.
•Avoid poorly ventilated locations.
If the floor is delicate against casters, when this machine is moved after installation, the floor material may be damaged.
During printing, some ozone is released, but the amount does not cause any ill effect to one’s health. If, however, the
machine is used over a long period of time in a poorly ventilated room or when printing an extremely large number of
copies, the smell may become unpleasant. To maintain the appropriate environment for print work, it is suggested that the
room be properly ventilated.
Cautions when Handling Consumables
Do not attempt to incinerate parts which contain toner. Dangerous sparks may cause burns.
Keep parts which contain toner out of the reach of children.
If toner happens to spill from parts which contain toner, avoid inhalation and ingestion, as well as contact with your
eyes and skin.
•If you do happen to inhale toner, move to a place with fresh air and gargle thoroughly with a large amount of
water. If coughing develops, contact a physician.
•If you do happen to ingest toner , rinse your mouth out with water and drink 1 or 2 cup s of water to dilute the contents of
your stomach. If necessary, contact a physician.
•If you do happen to get toner in your eyes, flush them thoroughly with water. If there is any remaining tenderness,
contact a physician.
•If toner does happen to get on your skin, wash with soap and water.
Do not attempt to force open or destroy parts which contain toner.
Other precautions
After use, always dispose of the Toner Container in accordance with Federal, State and Local rules and regulations.
Store all consumables in a cool, dark location.
If the machine will not be used for an extended period of time, remove the paper from the cassette, return it to its original
package and reseal it.
xii
About the Operation Guide
This Operation Guide contains the following chapters:
1 Machine Parts
This chapter lists the names of different machine parts.
2Preparation
This chapter explains how to start up the machine, load paper and originals, and use the application software included in
the Product Library disc.
3Copying
This chapter explains the functions you can use when copying.
4Printing
This chapter explains the printing procedure from an application software.
5 Scanning
This chapter explains the functions you can use when scanning originals.
6 Default Setting (System Menu)
This chapter explains how to use the System Menu to configure the machine.
7 FAX Operations
This chapter explains the functions you can use when faxing.
8 Maintenance
This chapter explains how to replace the toner container and how to care for your machine.
9 Troubleshooting
This chapter explains how to handle machine problems that may occur, such as paper jams.
10 Appendix
This chapter explains how to enter characters, and lists the machine specifications.
xiii
Conventions in This Guide
This manual uses the following conventions.
Convention Description Example
Italic Typeface Used to emphasize a key word , phrase
or reference to additional information. Refer to Connections on page 2-2.
Bold Used to denote buttons on the
software. To start printing, click OK.
Bracket Bold Used to denote operation panel keys. Press [Start] to start copying.
Courier Indicates characters entered in the
message display on the operation
panel.
Ready to Copy. appears in the message display on the
operation panel.
Note Used to provide additional or useful
information about a function or feature. Note Do not remove the toner container from the
carton until you are ready to install it in the machine.
Important Used to provide important information. IMPORTANT Take care not to touch the drum and
transfer roller (black) during cleaning.
Caution Used to suggest mechanical damage
as a result of an action. CAUTION When removing a paper jam, pull the paper
gently so as not to tear it. Torn pieces of paper are difficult
to remove and may be easily overlooked, deterring the
paper jam recovery.
Warning Used to alert users to the possibility of
personal injury. WARNING If you are shipping the machine, remove and
pack the developer unit and drum unit in a plastic bag and
ship them separately from the machine.
xiv
1-1
1 Machine Parts
This chapter explains the following topics:
Front Machine Components.................................................................................................................................. 1-2
Rear Machine Components................................................................................................................................... 1-3
Operation Panel........ .... ... ... ... ................ .... ... ... ... .... ... ................ ... ... .... ... ... ... ................ .......................................... 1-4
1-2
Machine Parts
Front Machine Co mponents
1Original Size Indicator Plates
2Slit Glass
3Platen
4Front Cover
5Paper Stopper
6Inner Tray
7Cassette Cover
8Cassette
9Operation Panel
10 Manual Feed Tray (FS-1025MFP, FS-1125MFP and FS-1325MFP)
11 Power Switch
12 Document Processor
13 Original Width Guides
14 Original Table
* The illustration shows the FS-1125MFP.
1
79
11
8
3
4
2
6
10
13
14
12
5
1-3
Machine Parts
Rear Machine Components
15 Rear Cover
16 Power Cord Connector
17 USB Interface Connector
18 Network Interface Connector (FS-1025MFP, FS-1125MFP and FS-1325MFP)
19 LINE Connector (FS-1120MFP, FS-1125MFP, FS-1320MFP and FS-1325MFP)
* The illustration shows the FS-1125MFP.
17
15
16
18
19
1-4
Machine Parts
Operation Panel
[Copy] key Displays the Copy screen.
[Scan] key Displays the Scan screen.
[FAX] key* Displays the FAX screen.
[Print Box] key Displays the Print Box screen.
[ID Card Copy] key Displays the ID Card Copy
screen.
[Address Book] key* Displays the Address Book
screen, where you can add
destinations.
[Address
Recall/Pause] key* Calls the previous destination.
Also used to enter a pause
when entering a FAX number.
[On Hook] key* Switches between on-hook
and off-hook when manually
sending a FAX.
* Only on the FS-1120MFP,
FS-1 125MFP, FS-1320MFP and
FS-1325MFP.
[Menu] key Displays functions and the System
Menu.
[Density] key Displays the density setting screen.
[] key / [] key Increments or decrements numbers,
or selects menu in the message
display. In addition, moves the cursor
when entering the characters.
[Back] key Returns to the previous display.
[OK] key Finalizes a function or menu, and
numbers that have been entered.
[Quiet Mode] key Turns on Quiet Mode.
Quiet Mode
If you prefer quiet operation,
press [Quiet Mode] to turn on
Quiet Mode. When Quiet Mode
is on, the print speed is slower.
Message Display Displays the setting menu,
machine status, and error
messages.
Processing
Indicator
(Green)
Flashing The machine is processing data.
Very slow
(5-second
interval)
flashing
The machine is in sleep mode.
Attention Indicator
(Amber) Lights or flashes when an error
occurs.
[Program 1] -
[Program 3]
key
Calls up the settings that
are registered in [Program
1] - [Program 3].
Numeric keys Enter numbers and symbols.
[Clear] key Clears entered numbers and
characters.
[Stop/Reset] key •Cancels the printing job in
progress.
•Returns settings to their
default states.
•Hold down two seconds to
pause printing. Hold down
two seconds again to
resume printing.
[Start] key Starts copying, scanning, and
FAX transmission operations.
2-1
2 Preparation
This chapter explains the following topics:
Connections ........................................................................................................................................................... 2-2
Loading Paper .......... ................ .... ... ... ... .... ... ................ ... ... .... ... ... ... ................. ... ... ... ... .......................................... 2-5
Loading Originals............ ................ ... ... .... ... ... ... ................ .... ... ... ... .... ... ................ ... ... .... .................................... 2-18
Installing and Uninstalling Drivers and Utilities................................................................................................ 2-20
Machine Settings.................................................................................................................................................. 2-26
Configuration........................................................................................................................................................ 2-48
Printing the Status Page...................................................................................................................................... 2-58
2-2
Preparation
Connections
This section explains how to start up the machine.
Connecting the USB Cable
Follow the steps as below for connecting the USB cable.
1Connect the USB cable to the machine’s USB interface connector.
2Connect the other end of the USB cable to the computer's USB interface connector.
Connecting the Network Cable (FS-1025MFP, FS-1125MFP and FS-1325MFP)
Follow the steps as below for connecting the network cable.
1Connect the network cable (not included) to the machine’s network interface connector.
2Connect the other end of the cable to the PC or your network device.
Note Use a USB cable with a rectangular Type A plug and a square Type B plug.
The USB cable should be shielded and no longer than 5 meters (16 feet) long.
Note Use shielded interface cables.
2-3
Preparation
Connecting the FAX Modular Cord (FS-1120MFP, FS-1125MFP, FS-1320MFP and
FS-1325MFP)
Follow the steps as below for connecting the modular cord.
1Connect the modular cord for the telephone line to LINE connector.
2Connect the other end of the modular cord to the modular jack.
Connecting the Power Cord
Install the machine close to an AC wall outlet. If an extension cord is used, the total length of the power cord plus extension
should be 5 meters (16 feet) or less.
1Connect the power cord to the power cord connector at the rear of the machine.
2Connect the other end of the power cord to a power outlet.
Note Only use the power cord supplied with the machine.
2-4
Preparation
3Press the power switch to On. The machine begins to warm up.
Starter Toner Container
The toner container packed with the new machine is a starter toner cont ainer. The starter toner cont aine r last s an average
of 700 pages (FS-1120MFP and FS-1320MFP) or 1,000 pages (FS-1025MFP, FS-1125MFP and FS-1325MFP).
IMPORTANT If you install the toner container and switch on the power, the start-up
screen (a rotating bar image) and then Adding toner... will be displayed on the
message display. When the machine is first switched on after toner installation, there
will be a delay of approximately 7 minutes before the machine gets ready to use. When
Ready to copy. appears in the message display on the operation panel, machine
installation is complete.
2-5
Preparation
Loading Paper
General Guidelines
The machine is designed to print on standard copier paper, but it can also accept a variety of other types of paper within
the limits specified below.
Selection of the right paper is important. Using the wrong paper can result in paper jams, curling, poor print quality, and
paper waste, and in extreme cases can damage the machine. The guidelines given below will increase the productivity of
your office by ensuring efficient, trouble-free printing and reducing wear and tear on the machine.
Paper Availability
Most types of paper are compatible with a variety of machines. Paper intended for xerographic copiers can also be used
with the machine.
There are three general grades of paper: economy, standard, and premium. The most significant difference between
grades is the ease with which they pass through the machine. This is affected by the smoothness, size, and moisture
content of the paper, and the way in which the paper is cut. The higher the grade of paper you use, the less risk there will
be of paper jams and other problems, and the higher the level of quality your printed output will reflect.
Differences between paper from different suppliers can also affect the machine's performance. A high-quality machine
cannot produce high-quality results when the wrong paper is used. Low-priced paper is not economical in the long run if it
causes printing problems.
Paper in each grade is available in a range of basis weights (defined later). The traditional standard weights are 60 to
120 g/m² (16 to 31.9b).
Paper Specifications
The following table summarizes the basic paper specifications. Details are given on the following pages:
Note The manufacturer assumes no liability for problems that occur when paper not satisfying these requirements
is used.
Item Specifications
Weight Cassette: 60 to 220 g/m² (16 to 58.5 lb/ream)
Manual Feed tray: 60 to 220 g/m² (16 to 58.5 lb/ream)
Thickness 0.086 to 0.110 mm (3.4 to 4.3 mils)
Dimensional Accuracy ±0.7 mm (±0.0276 inches)
Squareness of Corners 90 ±0.2°
Moisture Content 4 to 6%
Pulp Content 80% or more
2-6
Preparation
Minimum and Maximum Paper Sizes
The minimum and maximum paper sizes are as follows.
Selecting the Right Paper
This section describes the guidelines for selecting paper.
Condition
Avoid using paper that is bent at the edges, curled, dirty, torn, embossed, or contaminated with lint, clay, or paper shreds.
Use of paper in these conditions can lead to illegible printing and paper jams, and can shorten the life of the machine. In
particular, avoid using paper with a surface coating or other surface treatment. Paper should have as smooth and even a
surface as possible.
Composition
Do not use paper that has been coated or surface-treated and contains plastic or carbon. The heat of fusing can cause
such paper to give off harmful fumes.
Bond paper should contain at least 80% pulp. Not more than 20% of the total paper content should consist of cotton or
other fibers.
Paper Sizes
Cassette and the Manual Feed tray are available for the paper sizes shown below. The dimensional tolerances are
±0.7mm for the length and width. The angle at the corners must be 90° ±0.2°.
•A4 (210 × 297 mm)
•A5 (148 × 210 mm)
•A6 (105 × 148 mm)
•Folio (210 × 330 mm)
•JIS B5 (182 × 257 mm)
•ISO B5 (176 × 250 mm)
•Letter (8-1/2 × 11 inches)
•Legal (8-1/2 × 14 inches)
Cassette
70 mm
(2-3/4 inches)
148 mm (5-13/16 inches)
Minimum
Paper Size
Maximum
Paper Size
Manual Feed Tray
216 mm (8-1/2 inches)
356 mm (14 inches)
70 mm
(2-3/4 inches)
148 mm (5-13/16 inches)
Minimum
Paper Size
Maximum
Paper Size
216 mm (8-1/2 inches)
356 mm (14 inches)
2-7
Preparation
•Statement (5-1/2 × 8-1/2 inches)
•Executive (7-1/4 × 10-1/2 inches)
•Envelope Monarch (3-7/8 × 7-1/2 inches)
•Envelope #10 (4-1/8 × 9-1/2 inches)
•Envelope #9 (3-7/8 × 8-7/8 inches)
•Envelope #6-3/4 (3-5/8 × 6-1/2 inches)
•Envelope C5 (162 × 229 mm)
•Envelope DL (110 × 220 mm)
•Oficio II (216 × 340 mm, 8-1/2 × 13 inches)
•216 × 340 mm
•16 K (197 × 273 mm)
•Custom*
70 × 148 to 216 × 356 mm, 2-3/4 × 5-13/16 to 8-1/2 × 14 inches
* If the length of custom paper is larger than 297 mm (11-11/16 inches), the machine can be substituted A4, Folio,
Legal, and Oficio II as the standard paper size.
Smoothness
The paper should have a smooth, uncoated surface. Paper with a rough or sandy surface can cause blank spaces in the
printed output. Paper that is too smooth can cause multiple feeding and fogging problems. (Fogging is a gray background
effect.)
Basis weight
Basis weight is the weight of paper expressed in grams per square meter (g/m²). Paper that is too heavy or too light may
cause feed errors or paper jams as well as premature wear of the product. Uneven weight of paper, namely uneven paper
thickness may cause multiple-sheet feeding or print quality problems such as blurring because of poor toner fusing.
The recommended basis weight is between 60 and 220 g/m² (16 to 58.5 lib/ream).
Paper Weight Equivalence Table
The paper weight is listed in pounds (lb) and metric grams per square meter (g/m²). The shaded part indicates the
standard weight.
Thickness
The paper used with the machine should be neither extremely thick nor extremely thin. If you are having problems with
paper jams, multiple feeds, and faint printing, the paper you are using may be too thin. If you are having problems with
paper jams and blurred printing the paper may be too thick. The correct thickness is 0.086 to 0.110 mm (3.4 to 4.3 mils).
Europe Metric Weight
(g/m²) U. S. Bond Weight (lb) Europe Metric Weight
(g/m²) U. S. Bond Weight (lb)
60 16 128 34
64 17 135 36
75 20 148 39
80 21 157 42
81 22 163 43
90 24 176 47
100 27 199 53
105 28 220 58.5
120 32
2-8
Preparation
Moisture Content
Moisture content is defined as the percent ratio of moisture to the dry mass of the paper. Moisture can affect the paper’s
appearance, feed ability, curl, electrostatic properties, and toner fusing characteristics.
The moisture content of the paper varies with the relative humidity in the room. When the relative humidity is high and the
paper absorbs moisture, the paper edges expand, becoming wavy in appearance. When the relative humidity is low and
the paper loses moisture, the edges shrink and tighten, and print contrast may suffer.
Wavy or tight edges can cause jams and alignment anomalies. The moisture content of the paper should be 4 to 6%.
To ensure correct moisture content, it is important to store the paper in a controlled environment. Some tips on moisture
control are:
•Store paper in a cool, dry location.
•Keep the paper in its wrapping as long as possible. Re-wrap paper that is not in use.
•Store paper in its original carton. Place a pallet etc. under the carton to separate it from the floor.
•After removing paper from storage, let it stand in the same room as the machine for 48 hours before use.
•Avoid leaving paper where it is exposed to heat, sunlight, or damp.
Other Paper Properties
Porosity: Indicates the density of paper fiber.
Stiffness: Limp paper may buckle in the machine, resulting in paper jams.
Curl: Most paper naturally tends to curl one way if left unpacked. When paper passes through the fixing unit, it curls
upward a little. To produce flat printouts, load the paper so that the upward pressure from the machine can correct their
curling.
Electrostatic discharge: During the printing process the paper is electrostatically charged to attract the toner. The paper
must be able to release this charge so that printed sheets do not cling together in the Output Tray.
Whiteness: The contrast of the printed page depends on the whiteness of the paper. Whiter paper provides a sharper,
brighter appearance.
Quality control: Uneven sheet size, corners that are not square, ragged edges, welded (uncut) sheets, and crushed
edges and corners can cause the machine to malfunction in various ways. A quality paper supplier should take
considerable care to ensure that these problems do not occur.
Packaging: Paper should be packed in a sturdy carton to protect it from damage during transport. Quality paper obtained
from a reputable supplier is usually correctly packaged.
Specially treated p aper: We do not recommend printing onto the following types of p aper, even if it conforms to the basic
specifications. When you use these kinds of paper, purchase a small amount first as a sample to test.
•Glossy paper
•Watermarked paper
•Paper with an uneven surface
•Perforated paper
2-9
Preparation
Special Paper
The following types of special paper can be used:
•Preprinted paper
•Labels*
•Bond paper
•Recycled paper
•Thin paper* (60 to 64 g/m²)
•Rough paper
•Letterhead
•Colored paper
•Prepunched paper
•Envelopes*
•Cardstocks (Postcards)*
•Thick paper (90 to 220 g/m²)
•High-quality paper
* Only one sheet can be loaded at a time in the cassette or in the Manual Feed tray.
Use paper that is sold specifically for use with copiers or printers (heat-fusing type).
Since the composition and quality of special p aper vary considerably, special paper is more likely than white bond paper to
give trouble during printing. No liability will be assumed if moisture and so forth given off during printing on special paper
causes harm to the machine or operator.
Labels
One label sheet can be loaded at a time.
The basic rule for printing on adhesive labels is that the adhesive must never come into contact with any part of the
machine. Adhesive paper sticking to the drum or rollers will damage the machine.
Label paper has a structure comprising of th ree layers, as shown in the diagram. The top sheet is printed on. The adhesive
layer consists of pressure-sensitive adhesives. The carrier sheet (also called the linear or backing sheet) holds the labels
until used. Due to the complexity of its composition, adhesive-backed label paper is particularly likely to give printing
problems.
Adhesive label paper must be entirely covered by its top sheet, with no spaces between the individual labels. Labels with
spaces in between are liable to peel off, causing serious paper jam problems.
Note Before purchasing any type of special paper, test a sample on the machine and check that printing quality is
satisfactory.
Top sheet (white bond paper)
Adhesive
Carrier sheet
2-10
Preparation
Some label paper is manufactured with an extra margin of top sheet around the edge. Do not remove the extra top sheet
from the carrier sheet until after printing is finished.
The table below lists the specifications for adhesive label paper.
Postcards
One postcard can be loaded at a time. Make sure the postcards you are going to set are not curled. Feeding curled
postcards may cause paper jams.
Some postcards have rough edges on the back (those are created when the paper is cut). In this case, put the postcard on
a flat place and rub the edges with, for example, a ruler to smooth them.
Envelopes
One envelope can be loaded at a time. Envelopes should be fed in the face-up position, right edge first.
Since the composition of an envelope is more complex than that of ordinary paper, it is not always possible to ensure
consistent printing quality over the entire envelope surface.
Normally, envelopes have a diagonal grain direction. This direction can easily cause wrinkles and creases when envelopes
pass through the machine. Before purchasing envelopes, make a test print to check whether the machine accepts the
envelope.
•Do not use envelopes that have an encapsulated liquid adhesive.
•Avoid a long printing session for envelopes only. Extended envelope printing can cause premature machine wear.
Item Specification
Weight of top sheet 44 to 74 g/m² (12 to 20 lb/ream)
Composite weight 104 to 151 g/m² (28 to 40 lb/ream)
Thickness of top sheet 0.086 to 0.107 mm (3.9 to 4.2 mils)
Composite thickness 0.115 to 0.145 mm (4.5 to 5.7 mils)
Moisture content 4 to 6% (composite)
Top sheet
UnacceptableAcceptable
Carrier sheet
2-11
Preparation
Thick Paper
If an excessive amount of thick paper is loaded in the cassette, it may not be fed. In that case, reduce the number of
sheets to be loaded.
Fan the stack of paper and align the edges before loading them in the paper source. Some types of paper have rough
edges on the back (those are created when the paper is cut). In this case, put the paper on a flat place and rub the edges
once or twice with, for example, a ruler to smooth them. Feeding rough edged paper may cause paper jams.
Colored Paper
Colored paper should satisfy the same conditions as white bond paper. Refer to Paper Specific ations on page 2-5. In
addition, the pigments used in the paper must be able to withstand the heat of fusing during the printing process (up to
200°C or 392°F).
Preprinted Paper
Preprinted paper should satisfy the same conditions as white bond paper. Refer to Paper Specifications on page 2-5. The
preprinted ink must be able to withstand the heat of fusing during the printing process, and must not be af fected by silicone
oil.
Do not use paper with any kind of surface treatment, such as the type of paper commonly used for calendars.
Recycled Paper
Select recycled paper that meets the same specifications as the white bond paper except for whiteness. Refer to Paper
Specifications on page 2-5.
Note If paper is not fed even after its rough ed ges have been removed, warp the paper at the leading edge upward
for a few millimeters as shown in the figure, and then load the paper.
Note Before purchasing recycled paper, test a sample on the machine and check that the printing quality is
satisfactory.
Burrs
Burrs
2-12
Preparation
Paper Type
The machine is capable of printing under the optimum setting for the type of paper being used.
Not only can preset paper types be selected, but it is also possible for you to define and select customized paper types.
Paper type can be changed using the printer driver and KYOCERA Client Tool. The following types of paper can be used.
Yes: Can be stored No: Cannot be stored
Preparing the Paper
After removing paper from the packaging, fan through the sheets to separate them prior to loading.
If using paper that has been folded or is curled, straighten it prior to loading. Failure to do so may result in a paper jam.
Paper Type Paper Weight Displayed in
KYOCERA Client Tool Duplex
Path* Paper Type Paper Weight Displayed in
KYOCERA Client Tool Duplex
Path*
Plain Normal 2 Yes Color Normal 2 Yes
Preprinted Normal 2 Yes Prepunched Normal 2 Yes
Labels** Heavy 1 No Envelope** Heavy 2 No
Bond Heavy 1 Yes Cardstock** Heavy 2 No
Recycled Normal 2 Yes Thick Heavy 2 Yes
Vellum** Light No High quality Normal 2 Yes
Rough Heavy 1 Yes Custom 1 (to 8)*** Normal 2 Yes****
Letterhead Normal 2 Yes
* Automatic duplex printing is only possible on the FS-1025MFP, FS-1125MFP and FS-1325MFP.
** One sheet must be loaded at a time.
*** This is a paper type defined and registered by the user. Up to eight types of user settings may be defined. For
more information, refer to KYOCERA Client Tool User Guide.
**** When Custom is specified, duplex printing can be set in KYOCERA Client Tool.
IMPORTANT Ensure paper is not stapled and clips are removed.
You should not use inkjet printer paper or any paper with a special surface coating. (Such papers may cause paper
jams or other faults.)
2-13
Preparation
Loading Paper into Cassette
250 sheets of A4 or Letter paper (80 g/m²) may be loaded into the cassette.
1Open the cassette cover.
2Adjust the position of the width guides located on the left and right sides of the cassette.
Note When using paper that is larger than A4/Letter, remove the cassette cover.
Gently press on both the left and right sides of the cassette cover and pull.
If necessary, open the paper stopper shown in the figure.
Note Paper sizes are marked on the cassette.
1 2
2-14
Preparation
3Adjust the paper length guide to the paper size required.
Note When using paper larger than A4/Letter, pull out the paper length guide.
When using A6 paper, attach the stopper.
Move the stopper to the A6 position.
2-15
Preparation
4Load the paper all the way in the cassette until the paper touches the far inner side. Ensure
the side to be printed is facing up and the paper is not folded, curled, or damaged.
IMPORTANT Adjust so that there is no gap between the paper length guide and the
paper.
Note Load an amount of paper that fits under (does not contact) the tabs on the width
guides.
When using A6 paper, load the paper as shown in the illustration.
2-16
Preparation
5Close the cassette cover.
6Specify the paper size and type for the cassette using KYOCERA Client Tool. For more
information, refer to Configuration on page 2-48.
When you attach the cassette cover
Attach the cassette cover as shown.
Loading Paper into Manual Feed Tray
The FS-1025MFP, FS-1125MFP and FS-1325MFP can load one sheet into the Manual Feed tray.
1Adjust the position of the paper guides on the Manual Feed tray. Standard paper sizes are
marked on the Manual Feed tray. For standard paper sizes, slide the paper guides to the
corresponding mark.
Note When storing the cassette, or when using paper larger than A4/Letter, remove
the cassette cover.
Note Set the same paper size to the paper size that is set on the machine.
2-17
Preparation
2Align the paper with the paper guides and insert as far as it will go.
3Specify the paper size and type for Manual Feed tray using KYOCERA Client Tool. For
more information, refer to Configuration on page 2-48.
Note If the paper is considerably curled in one direction, for example , if the p aper is
already printed on one side, try to roll the paper in the opposite direction to counteract
the curl.
When loading an envelope, load as shown in the illustration.
Load envelope with the print side facing up.
Note Set the same paper size to the paper size that is set on the machine.
Correct Incorrect
Close the flap.
2-18
Preparation
Loading Originals
Placing Originals on the Platen
You may place books or magazines on the platen in addition to ordinary sheet originals.
Open the document processor, and place the original.
Loading Originals in the Document Processor
The document processor automatically scans each sheet of multiple originals.
Originals Supported by the Document Processor
Note Before opening the document processor, be sure that there are no originals left on the original table or on the
original eject table. Originals left on the original table or on the original eject table may fall off when the document
processor is opened.
Shadows may be produced around the edges and in the middle of open-faced originals.
CAUTION Do not leave the document processor open as there is a danger of personal
injury.
IMPORTANT Do not push the document processor forcefully when you close it. Excessive
pressure may crack the platen. (Allowable load weight: 5 kg or less)
When placing books or magazines on the machine, do so with the original cover or the
document processor in the open position.
Align it flush against the
original size indicator plates
with the back left corner as the
reference point.
Put the scanning
side facedown.
Weight 60 to 105 g/m²
Size Maximum Folio to Minimum A6
Maximum Legal to Minimum Statement-R
Capacity Plain paper (80 g/m²), Colored paper, Recycled paper: 40 sheets
Vellum (60 g/m²): 25 sheets
Thick paper (90 g/m²): 35 sheets
Thick paper (100 g/m²): 30 sheets
Thick paper (120 g/m²): 25 sheets
2-19
Preparation
Originals Not Supported by the Document Processor
•Soft originals such as vinyl sheets
•Transparencies such as OHP film
•Carbon paper
•Originals with very slippery surfaces
•Originals with adhesive tape or glue
•Wet originals
•Originals with correction fluid which is not dried
•Irregularly shaped (non-rectangular) originals
•Originals with cut-out sections
•Crumpled paper
•Originals with folds (Straighten the folds before loading. Failure to do so may cause the
originals to jam.)
•Originals bound with clips or staples (Remove the clips or staples and straighten curls,
wrinkles or creases before loading. Failure to do so may cause the originals to jam.)
How to Load Originals
1Adjust the original table size.
2Load originals.
Put the side to be scanned face-up. Slide the leading edge into the document processor as
far as it will go.
IMPORTANT Before loading originals, be sure that there are no originals left on the original eject table. Originals left
on the original eject table may cause the new originals to jam.
Note Ensure that loaded originals do not exceed the level indicator. Exceeding the
maximum level may cause the originals to jam (see the figure).
Confirm that the original width guides exactly fit the originals. If there is a gap,
readjust the original width guides. The gap may cause the originals to jam.
2-20
Preparation
Installing and Uninstalling Drivers and Utilities
This section explains how to configure machine settings and install the software required for use as a machine. Ensure the
machine is plugged in and connected to the PC before installing the software from the Product Library disc.
Software
The following software can be installed from the provided Product Library disc.
: Installed standard. : Installed if selected.
Note Install the software when the machine status is online*.
*Ready to copy, Ready to print, Ready to scan or Enter destination appears in the
message display.
Software Function Description
Installation Method Reference
Page
Express
Install Custom
Install
GX DRIVER Print Driver for printing files on a computer using
the machine. This printer driver enables full
use of the machine’s features.
Printer
Driver User
Guide
GX XPS DRIVER Printer driver for XPS (XML Paper
Specification) format developed by Microsoft
Corporation.
—
TWAIN Driver*
* The machine must be connected by USB.
Scan Driver for scanning on the machine using a
TWAIN-compatible software application. 5-5
WIA Driver* WIA (Windows Imaging Acquisition) is a
function of Windows that enables reciprocal
communication between an imaging device
such as a scanner and an image processing
software application. An image can be
acquired using a WIA-compliant software
application, which is convenient when a
TWAIN-compliant software application is not
installed in the computer.
5-5
FAX Driver**
** Only on the FS-1120MFP, FS-1125MFP, FS-1320MFP and FS-1325MFP.
FAX Driver for sending faxes from any computer
connected by USB or network cable. 7-37
KYOCERA Net
Viewer Utility Utility that enables the machine to be
monitored when connected to a network. —KYOCERA
Net Viewer
User Guide
KYOCERA Client
Tool Utility that enables current and all supported
devices status, features and settings to be
accessed.
When KYOCERA Client Tool is installed, the
following utilities are installed.
•Status Monitor (page 2-31)
•Preset Tool (page 2-32)
•Configuration (page 2-48)
•Maintenance Menu (page 8-8)
2-26
FAX Address
Book Utility** Utility for saving fax numbers and creating
group faxes. 2-39
2-21
Preparation
Installing the Software in Windows
If you are connecting this machine to a Windows PC, follow the next steps to install the software. The example shows you
how to connect your machine to a Windows 7.
You can use either Express Install or Custom Install to install the software. Express Inst all automatically detect s connected
machines and installs the required software. Use Custom Install if you want to specify the printer port and select the
software to be installed.
1Turn on the computer and start up Windows.
If the Welcome to the Found New Hardware Wizard dialog box displays, select Cancel.
2Insert the Product Library disc supplied with the machine into the optical drive. In Windows
7, Windows Server 2008 and Windows Vista, the user account control window may appear.
Click Yes.
The installation program launches.
3Click View License Agreement and read the License Agreement. Click Accept.
The software install wizard starts up.
From this point, the procedure differs depending on your version of Windows and your
connection method. Proceed to the correct procedure for your connection type.
•Express Install
•Custom Install
Express Install
In Express Install, the installer automatically detects the machine when it is turned on. Use Express Install for standard
connection methods.
1Select the Express Install tab. The installer detects the machine.
Note In Windows operating systems, you must be logged in with administrator privileges to install the software.
Note If the software install wizard does not launch automatically, open the Product
Library disc window in Windows Explorer and double-click Setup.exe.
2-22
Preparation
If the installer does not detect a print system, check that the print system is connected via
USB or a network and that it is turned on. Then click (Refresh) to search print system
again.
2Select the machine you want to install, select the Driver Package, and click Install.
3A message appears saying that your software is ready to use. To print a test page, select
the Print a test page checkbox and select the machine.
Click Finish to exit the installation wizard.
This completes the software installation procedure.
Custom Install
Use Custom Install if you want to specify the printer port and select the software to be installed.
1Select Custom Install tab.
2Select the device to be installed, and click the arrow button to move it to the Products to
Install list.
3Select the software to be installed, and click the arrow button to move it to the Prod uct s to
Install list.
4Click Install.
5A message appears saying that your software is ready to use. To print a test page, select
the Print a test page checkbox and select the machine.
Click Finish to exit the installation wizard.
This completes the software installation procedure.
Note While the information shown in Windows 7 and Windows Vista/Windows XP
installation dialog boxes differs slightly, the installation procedure is the same.
Network connection is only possible with the FS-1025MFP, FS-1125MFP and
FS-1325MFP.
Note If the Found New Hardware Wizard appears, click Cancel. If a hardware
installation warning message appears, click Continue.
If the Windows security window appears, click Install this driver software anyway.
2-23
Preparation
Installation on a Macintosh
This section explains how to install the printer driver in Mac OS.
1Turn on the machine and the Macintosh.
2Insert the Product Library disc supplied with the machine into the optical drive.
3Double-click the Product Library disc icon.
4Double-click OS X 10.5 or higher.
5Double-click Kyocera OS X 10.5+ xxxxx.
6The printer driver installation program starts up.
7Install the printer driver as directed by the instructions in the installation software.
This completes the printer driver installation. If a USB connection is used, the machine is
automatically recognized and connected.
(FS-1025MFP, FS-1125MFP and FS-1325MFP)
If an IP connection is used, the settings below are required.
IMPORTANT In the Authentication screen , en ter the na me an d pa ssword used to log
in to the operating system.
2-24
Preparation
8Open System Preferences and click Print & Fax.
9Click the plus symbol (+) to add the installed printer driver.
10Click the IP icon for an IP connection and then enter the IP address and printer name.
11Select the installed printer driver and click Add.
12The selected machine is added. This completes the machine setup procedure.
2-25
Preparation
Uninstalling Drivers and Utilities
The software can be uninstalled (removed) using the Product Library disc supplied with the machine.
1Exit all active software applications.
2Insert the Product Library disc supplied with the machine into the optical drive. In Windows
7, Windows Server 2008 and Windows Vista, the user account control window may appear.
Click Yes.
3Following the procedure used to install the software, click Uninstall tab.
4Select the software to remove.
5Click Uninstall.
The uninstaller starts.
6When Uninstall complete screen appears, click Finish.
7If Restart Your System screen appears, select whether you restart your computer or not,
and click Finish.
IMPORTANT On Macintosh computers, because the machine settings are specified using a PPD (PostScript Printer
Description) file, the software cannot be uninstalled using the Product Library disc.
Note When KYOCERA Net Viewer is installed, separate uninstallers are launched for this application. Proceed with
the uninstallation steps for this application as directed by the on-screen instructions.
2-26
Preparation
Machine Settings
Various machine settings can be configured from a computer using KYOCERA Client Tool. Install KYOCERA Client Tool
from the provided Product Library disc.
Accessing KYOCERA Client Tool
Start KYOCERA Client Tool.
KYOCERA Client Tool Functions
The functions of KYOCERA Client Tool are described below.
Note For the detailed functions of KYOCERA Client Tool, refer to KYOCERA Client Tool User Guide.
Function Description Reference Page
KYOCERA Client Tool KYOCERA Client Tool gives you quick access to common
machine features and settings, plus the current status of all
supported machines. You can also use KYOCERA Client Tool to
order toner, download printer drivers, access KYOCERA Net
Viewer, open the company website and view machine
documentation.
2-27
Status Monitor Lets you view the status of the machine on your desktop. 2-31
Preset Tool Registers the Copy, Scan, FAX and Print Box programs. 2-32
Address Book*
* Only on the FS-1120MFP, FS-1125MFP, FS-1320MFP and FS-1325MFP.
Registers the destination used for FAX. 2-39
Configuration Allows user to configure machine settings, including energy
saving, paper settings and network settings. Messages shown in
the Status Monitor are also configured here.
2-48
Maintenance Menu For machine maintenance. Use when print quality deteriorates or
to adjust the print or scan position. 8-8
2-27
Preparation
KYOCERA Client Tool Settings
General
1
2
7
8
3
4
9
6
5
No. Item Description Reference
Page
1Machine list The list at the top of KYOCERA Client Tool screen
includes all of the supported machines installed on
your computer. You can select a machine from this
list to view its properties and select available options,
such as configuration, maintenance, and driver
download.
—
2Print The Print tab gives you access to printing
preferences and machine driver properties. Click
Preferences or Properties to open the settings.
2-28
3 Device The Device tab lets you configure a machine, view
documentation, restart a machine and restore
factory default settings.
Click Configuration to display the Configuration
screen. This lets you configure various machine
settings. Refer to Configuration on page 2-48.
2-29
4 Scan The Scan tab lets you configure TWAIN and Quick
Scan settings.
Scan to PDF, Scan to Email and Scan to Folder can
also be executed from this tab.
Note The Scan tab only appears when the machine
is connected by USB.
2-29
2-28
Preparation
Print Tab
5FAX The FAX tab lets you select FAX settings and edit
Address Book destinations. For details, refer to
Address Book
on page 2-39.
Note This setting only appears on the FS-1120MFP,
FS-1125MFP, FS-1320MFP and FS-1325MFP.
2-30
6 Maintenance The Maintenance tab lets you open KYOCERA Net
Viewer*, order replacement toner, view our web site,
and download software.
Click Maintenance Menu to display the
Maintenance Menu screen. This lets you perform
machine maintenance. Refer to Maintenance Menu
on page 8-8.
2-30
7Machine status This shows a 3D image of the selected machine and
its current status. Click (Refresh) to refresh the
machine status.
—
8 Supplies The Supplies tab shows the toner status. —
Device Overview The Device Overview tab shows the machine
settings. —
9Close Clicking Close hides KYOCERA Client Tool. —
* To display KYOCERA Net Viewer, KYOCERA Net Viewer must be installed.
No. Item Description Reference
Page
1
2
No. Item Description
1 Preferences Opens the Printing Preferences screen for the selected machine.
2 Properties Opens the Properties screen for the selected machine.
2-29
Preparation
Device Tab
Scan Tab
1
2
3
5
4
No. Item Description Reference Page
1 Configuration Opens the Configuration screen for the
selected machine. 2-48
2 Preset Opens the Preset Tool screen for the
selected machine. 2-32
3 Documentation Opens the folder where manuals are
contained. —
4 Device restart Click the Device restart icon to restart the
machine. Click Yes to confirm. You must be
logged in with administrator privileges on your
PC.
—
5 Factory default Click the Factory default icon to return all of
the machine properties of the selected model
to its default settings. Click OK to confirm.
You must be logged in with administrator
privileges on your PC.
—
1
2
3
5
4
No. Item Description Reference Page
1 Preferences Opens TWAIN screen. Set the default value
for the TWAIN scan. 2-45
2 Quick Scan
Settings Opens Quick Scan screen. 2-45
3 Scan to PDF Saves the scanned image in PDF format. 5-4
4 Scan to Email Attaches the scanned image to a new E-mail
message. 5-4
5 Scan to Folder Saves the scanned image to a specified
folder. 5-4
Note To use Scan functions, the machine must be connected by USB.
2-30
Preparation
FAX Tab
Maintenance Tab
1
2
3
No. Item Description Reference Page
1 Preferences Opens FAX Printing Preferences screen. 7-40
2 Properties Opens FAX Properties screen. FAX Driver User
Guide
3 Address Book Opens FAX Address Book Utility screen. 2-39
1
2
4
5
3
No. Item Description Reference Page
1 Maintenance
Menu Opens Maintenance Menu screen. 8-8
2 KYOCERA Net
Viewer Opens KYOCERA Net Viewer.*
* To display KYOCERA Net Viewer, KYOCERA Net Viewer must be installed.
KYOCERA Net
Viewer User Guide
3 Order Toner You can order replacement toner by e-mail or
on the web. Click the Order Toner icon for
these options:
•Send e-mail
Use the default e-mail address or type
another e-mail address and then click OK
to open your default e-mail program.
•Open Web page
Use the default web address or type
another web address and then click OK to
open the web page in your default web
browser.
—
4 Kyocera Online Opens our website. —
5 Driver Download Click to open the download page of our
website. You can download software and find
an authorized dealer.
—
2-31
Preparation
Status Monitor
When KYOCERA Client Tool is installed, you can check the machine status in the Status Monitor icon.
The Status Monitor icon displays machine status messages in the lower right corner of the screen.
Screen Overview
The screen overview of the Status Monitor icon is as follows.
When the Status Monitor icon is active, you can select KYOCERA Client Tool options by
right-clicking the icon in the system tray.
No. Item Description
1Pop-up window If an information notification event occurs, a pop-up window
appears.
Information notification events can be set in the Configuration.
Refer to Configuration on page 2-48.
2Status Monitor
icon The Status Monitor icon is displayed in the taskbar notification
area when the Status Monitor is running.
No. Item Description
1 Show/Hide the
KYOCERA Client Tool Switches between hiding and showing KYOCERA Client
Tool screen.
2(URL) Opens our website.
3Exit Closes KYOCERA Client Tool and removes the Status
Monitor icon from the system tray.
1
2
1
2
3
2-32
Preparation
Default and Program Settings
This section explains about the Copy, Print Box, Scan and FAX default settings and programs. For settings that are
frequently changed from the default settings, it is convenient to register a program.
Default Settings
This section explains the default settings for each function.
Program Settings
If you have settings that are frequently changed from the default settings, register the settings in a program. You can
simply select the program number as needed to recall those functions.
Programs can be registered from a computer using Preset Tool. The Preset Tool is a function of KYOCERA Client Tool.
Three programs can be registered per function.
This section explains how to register a program. To use a registered program, refer to the pages of each function.
•Copy: Basic Operation on page 3-2
•Scan: Push Scan on page 5-2
•FAX: Basic transmission procedure on page 7-12
•Print Box: Printing from Print Box on page 4-7
Accessing the Preset Tool
1Start KYOCERA Client Tool as explained in Accessing KYOCERA Client Tool on
page 2-26.
2Click Preset on the Device tab. The Preset Tool opens.
Functions Description
Copy The default settings for Copy are changed with the Configuration. For details, refer to
Configuration on page 2-48.
Print Box It is not possible to change the default settings for Print Box. The job stored in the Default
folder is printed. The Program is used to select the Print Box. Refer to Program Settings on
page 2-32.
Push Scan It is not possible to change the default settings for Push Scan. The Program is used to change
the settings. Refer to Program Settings on page 2-32.
FAX The default settings for FAX are changed with the Configuration. For details, refer to
Configuration on page 2-48.
2-33
Preparation
General
1
2
7
8
9
3 4 5 6
No. Item Description Reference
Page
1Program number Select the program number (1 to 3) to be registered. When a program number is
selected, the settings registered in that number appear in the right-hand screen. —
2Summary Shows a list of the settings of the selected program. —
3Copy Set programs for the Copy function. 2-34
4 Scan Set programs for the Scan function. 2-36
5FAX Set programs for the FAX function.
Note This setting only appears on the FS-1120MFP, FS-1125MFP,
FS-1320MFP and FS-1325MFP.
2-37
6Print Box Set programs for the Print Box function. 2-38
7 Reset Reset the program to default values. —
8 Save Save your settings. —
9Close Close the Preset Tool. —
2-34
Preparation
Copy Tab
1
2
3
4
5
7
8
9
10
11
12
6
No. Item Description
1 Original size Specify the size of originals being scanned.
Value: Executive, Letter, Legal, A4, A5, A6, B5 (JIS), B5 (ISO), Custom,
216 × 340 mm, Oficio II, 16K, Statement, Folio
Note Refer to Configuration on page 2-48 for selecting Custom.
2 Original image Select image quality suited to the type of original.
Value:
3 Resolution The resolution is selected when Text + Photo is selected in Original image. Select
600 dpi when you want good reproduction of fine text and lines in originals which
contain a mixture of text and photos.
Value:
Note The Photo and Text selections in Original image are fixed at 300 dpi.
4Copies* Set the default value for the number of copies.
Value: 1 to 99
5Collate Scan multiple originals and deliver complete sets of copies as required according to
page number.
Value:
6 Original orientation Select the orientation of the original document top edge to scan correct direction.
Value:
Text + Photo Photo Text
300 dpi 600 dpi
Off On
Top Edge Left Top Edge Top
2-35
Preparation
7Zoom Adjust the magnification to reduce or enlarge the original image.
Value: 100%, Auto, Custom, Fixed
When Custom or Fixed is selected, the Zoom screen is displayed.
8 Density Adjust density using 7 levels.
Value: Lighter (-3), Lighter (-2), Lighter (-1), Normal (0), Darker (+1), Darker (+2),
Darker (+3)
9EcoPrint Use EcoPrint to save toner when printing. Use this function for test copies or any other
occasion when high quality print is not required.
Value:
10 Duplex Select duplex copying.
Value:
Note This setting only appears on the FS-1025MFP, FS-1125MFP and FS-1325MFP.
11 Combine Combine 2 or 4 original sheets into 1 copied page.
Value:
12 Layout You can select the page layout.
Value:
Note For details on page layout, refer to Combine on page 3-9.
* Non-numeric characters cannot be entered. If entered number is beyond range, the max/min value will be
restored.
No. Item Description
Zoom level (Fixed)
Adjusts the image to match present
sizes.
Custom*
Specify the image size in 1% increment
between 25% - 400% of the original.
On Off
Simplex Binding Left/Right Binding Top
Off 2in1 4in1
2in1 4in1
Left to right Right to left
Right then
down Down then
right Left then
down Down then
left
2-36
Preparation
Scan Tab
1
2
3
4
9
5
6
7
11
12
8
10
No. Item Description
1Name Set a name for the Program. This name is displayed in the message display of the
machine’s operation panel. Up to 18 characters can be entered.
2 Original size Specify the size of originals being scanned.
Value: Executive, Letter, Legal, A4, A5, A6, B5 (JIS), B5 (ISO), Custom,
216 × 340 mm, Oficio II, 16K, Statement, Folio
Note Refer to Configuration on page 2-48 for selecting Custom.
3 Original image Select image quality suited to the type of original.
Value:
4 Reverse image When this is selected, the image color reverses.
5Sharpen Adjust the sharpness of the image.
Value: None, Low, Medium, High, Descreen (Blurs the outlines and reduces the
sharpness.)
6 Scan color Select the color mode setting.
Value: Monochrome, Grayscale, Full color
7 Density Select the density.
Value: Lighter (-3), Lighter (-2), Lighter (-1), Normal (0), Darker (+1), Darker (+2),
Darker (+3)
8 Resolution Select fineness of scanning resolution.
Value:
9 Output name Assign a document name to scanned images. When there are multiple pages, a
three-digit incrementing number such as Scan_001, Scan_002... is appended to the
end of the file name. Up to 16 characters can be entered.
10 File format Specify the image file format.
Value: BMP, JPEG, PNG, TIFF, PDF
Text + Photo Photo Text
200×200 dpi 300×300 dpi 400×400 dpi 600×600 dpi
2-37
Preparation
FAX Tab
11 Quality Set the quality if File format is JPEG. This is disabled for non-JPEG format.
Value: 1 to 100
Note Non-numeric characters cannot be entered. If entered number is beyond range,
the max/min value will be restored.
12 Destination folder Enter the path of the folder where the scanned image will be saved. Either
C:\User\<user>\My Documents (on Windows Vista/Windows 7) or C:\Document and
Settings\<user>\My Documents (on Windows XP) is set as the default.
To select the folder, click Browse to open Browse for Folder.
No. Item Description
1
2
6
5
3
7
4
8
No. Item Description
1 Original size Specify the size of originals being scanned.
Value: Executive, Letter, Legal, A4, A5, A6, B5 (JIS), B5 (ISO), Custom,
216 × 340 mm, Oficio II, 16K, Statement, Folio
Note Refer to Configuration on page 2-48 for selecting Custom.
2 Original image Select image quality suited to the type of original.
Value:
3 Density Adjust density using 7 levels.
Value: Lighter (-3), Lighter (-2), Lighter (-1), Normal (0), Darker (+1), Darker (+2),
Darker (+3)
4 Resolution Select fineness of scanning resolution.
Value:
5 Destination list The destination is displayed.
Text + Photo Photo Text
200×100 dpi 200×200 dpi 200×400 dpi
2-38
Preparation
Print Box Tab
6New Opens Add/Edit FAX List screen.
7Edit A new destination can be added by clicking New. To edit a
destination, select the destination from the list and click
Edit. The destinations stored in the Address Book on the
machine are displayed.
•Directly enter a fax number.
Enter a fax number, and set TX start speed and ECM.
•Select from the Address Book.
Select the Select from Address book check box and
then choose from the destinations displayed.
Note Up to 100 destinations can be added. When a group
is selected from the Address Book, it is converted into the
contact destinations.
Click OK to apply the destination addition or change and
return to the FAX tab.
8 Delete To delete a destination, select the destination from the list and click Delete.
No. Item Description
1
2
3
4
5
No. Item Description
1Name Set a name for the Program. This name is displayed in the message display of the
machine’s operation panel. Up to 18 characters can be entered.
2 Connection Select the interface used to connect with the machine.
Value: Local, Network
3 Destination folder
(Local) Enter the path for the folder to be used as the Print Box. Program 1 is Box 1,
Program 2 is Box 2 and Program 3 is Box 3.
To select the folder, click Browse to open Browse for Folder.
4 IP address (IPv4) Set the IP address for the computer with the Print Box to be used.
Value: ###.###.###.###
If you select Network for Connection, this setting is available.
5 Destination folder
(Network) Enter the path for the folder to be used as the Print Box. Program 1 is Box 1,
Program 2 is Box 2 and Program 3 is Box 3.
To select the folder, click Browse to open Browse for Folder.
If you select Network for Connection, this setting is available.
2-39
Preparation
Address Book
Edit FAX destinations in the Address Book. This setting only appears for the FS-1120MFP, FS-1125MFP, FS-1320MFP
and FS-1325MFP.
Accessing the FAX Address Book Utility
1Start KYOCERA Client Tool as explained in Accessing KYOCERA Client Tool on
page 2-26.
2Click Address Book on the FAX tab. The FAX Address Book Utility opens.
Overview
The Address Book used as follows.
Note FDT file is our Address Book file format for FAX. The Address Book can be exported to another FAX from an
FDT file.
FDT*
Open the Address Book.
page 2-40
Save the Address Book.
page 2-43
FA X Address Book Utility
Edit the Address Book. page 2-41
Open the Address Book.
page 2-40
Save the Address Book.
page 2-43
2-40
Preparation
FAX Address Book Utility Screen
Opening the Address Book
Open an Address Book to be edited.
No. Item Description Reference
Page
1Main Toolbar Quick access to some important functionalities. —
2Address Book list Shows all address and group entries in the open
Address Book. —
3Add Add a new entry to the list. 2-41
4Edit Change an entry selected from the list. 2-42
5 Delete Delete the entries selected from the list. 2-42
6Contact Enter the Name, FAX Number, Company, and
Department for the entry to be registered in the
Address Book and set the FAX communication
speed and the ECM. These are enabled when Add
or Edit is clicked.
Note Name, Company and Department are used
on the cover page when sending a fax. Company
and Department will not be saved on the device and
FAX communication speed and ECM will not be
saved on the file.
2-41
7Status bar Shows the current status of the menu. —
1
3
6
2
4
5
7
Read in the Address Book from the machine.
Open an Address Book from an FDT file.
Create a new Address Book.
2-41
Preparation
Editing the Address Book
Add and edit entries in the Address Book. A combined total of 120 contact and group entries can be added.
Adding a Contact 1Click Add.
2Enter the information of the entry.
3Click Save. The new entry appears in the list at the top of the screen.
Adding a Group 1Click Add group icon.
No. Item Description
1Name Enter the Name. Up to 32 characters can be entered.
2FAX Number Enter the FAX Number. Up to 32 characters can be entered.
3FAX
communication
speed
Configure the FAX communication start speed.
Value: 9600 bps, 14400 bps, 33600 bps
Note Normally the default setting should be used.
4ECM Turn on ECM communication.
ECM (error correction mode) is a function to automatically
resend an image that has not been correctly sent or received
due to the effects of noise on the telephone line during
transmission.
5 Save Save the information that you entered.
6 Cancel Cancel the information that you entered.
1
2
3
4
5
6
2-42
Preparation
2Enter the information of the group being added.
3Click OK to add the group and exit Add Group. Click Cancel to exit Add Group without
adding the group.
Editing Address Book Entries
•Edit a contact entry.
Select the contact entry to be edited and click Edit. Edit the contact entry and click Save.
For the information in contact entries, refer to Adding a Contact on page 2-41.
No. Item Description
1 Group name Enter the Group Name. The name entered here will appear
in the list in the Address Book. Up to 32 characters can be
entered.
2 All contacts Shows all entries (contacts only) registered in the opened
Address Book.
3>> Move the entry selected in the All contacts list to the
Selected contacts list. Up to 100 entries can be selected.
4<< Delete the selected entry from the Selected contacts list
and returns it to the All contacts list.
5 Selected contacts Shows the entries in the group.
1
25
3
4
2-43
Preparation
•Edit a group entry.
Select a group entry to be edited and click the Edit group icon. The Edit Group Entry
screen appears. Edit the group entry information and click OK.
For the information in group entries, refer to Adding a Group on page 2-41.
•Delete an entry.
Select the entry to be deleted from the list, and click Delete.
Saving the Address Book
When you have finished editing the Address Book, save the Address Book in the machine or in an FDT file.
Registering Reject List
Register a Reject List for RX Restriction.
Reception from FAX numbers registered in the Rejected numbers (blocked numbers) will be rejected. Reception from
parties that do not provide fax number notification can also be rejected.
To enable RX Restriction, set RX Restriction in the Reject List. For more information, refer to RX Restriction on page 7-34.
Note The Edit Group Entry screen can also be opened by double-clicking the group
entry to be edited.
Save the Address Book in the machine.
Save the Address Book as an FDT file with a different name.
Save the Address Book in the FDT file.
2-44
Preparation
1Click Block numbers icon.
2Enter the Rejected numbers (blocked numbers) information.
3Click the Save to device icon to save the Rejected numbers in the machine.
Note Rejected numbers (blocked numbers) are stored in the machine. To read in the
numbers stored in the machine, click the Block numbers icon.
No. Item Description
1 Load from
Device Load Rejected numbers (blocked numbers) information from
the machine.
2 Enable number
blocking Select this checkbox to reject reception from rejected numbers
(blocked numbers).
To enable this setting, select this checkbox and set the
Reject List as explained in Setting RX Restriction on
page 7-34.
3FAX number Enter a F AX number from which reception will be rejected. Up
to 20 characters can be entered. Click Add to add the number
to the list at the bottom of the screen.
4 Block all
unknown
numbers
Select this checkbox to reject reception from parties that do
not provide fax number notification.
To enable this setting, select this checkbox and set Reject
as explained in Unknown Number RX on page 7-34.
5 Blocked
numbers list Shows the numbers that have been registered in Rejected
numbers (blocked numbers). Up to 10 Rejected numbers
(blocked numbers) can be registered.
6 Delete To delete numbers from Rejected numbers (blocked
numbers), select the numbers in the list and click Delete.
7 Cancel Exit without registering Rejected numbers (blocked numbers).
2
3
4
5
6
7
1
2-45
Preparation
Quick Scan/TWAIN Settings
Settings required for scanning on the machine are explained below. The settings specified here will be the default settings
for scanning.
1Start KYOCERA Client Tool as explained in Accessing KYOCERA Client Tool on
page 2-26.
2Click Preferences or Quick Scan Settings on the Scan tab.
TWAIN Settings
Item Description
Preferences Change the TWAIN scan settings. This setting is effective for Quick Scan only.
Quick Scan Settings Change the settings for Scan to PDF, Scan to Email, and Scan to Folder.
No. Item Description
1 Original size Specify the size of originals being scanned. The sizes that can be
selected vary depending on the Feed method setting.
Value: (when the Feed method is Auto or Platen) Letter,
Statement, Executive, A4, A5, A6, B5 (JIS), B5 (ISO), 16K,
Custom
(when the Feed method is Document Processor) Letter, Legal,
Statement, Executive, A4, A5, A6, Folio, B5 (JIS), B5 (ISO),
Oficio II, 16K, 216 × 340 mm, Custom
Note Refer to Configuration on page 2-48 for selecting Custom.
1
3
4
9
5
6
7
8
10 11
2
2-46
Preparation
Quick Scan Settings
2 Feed method Select the original feed method.
Value: Auto, Document Processor, Platen
3 Scan color Select the color mode setting.
Value: Monochrome, Grayscale, Full color
4 Resolution Select fineness of scanning resolution.
Value: 200 × 200 dpi, 300 × 300 dpi, 400 × 400 dpi,
600 × 600 dpi
5Sharpen Adjust the sharpness of the image.
Value: None, Low, Medium, High, Descreen (Blurs the outlines
and reduces the sharpness.)
6 Original image Select original image type for best results.
Value: Text, Photo, Text+Photo
7 Destiny Select the density.
Value: -3 (Lighter) to 3 (Darker)
8 Reverse image When this is selected, the image color reverses.
9 Reset Reset the settings to the previous settings.
10 Help Displays the Help screen.
11 OK/Close Clicking OK exits the TWAIN Settings after applying the modified
scan settings.
Clicking Close exits the TWAIN Settings without applying the
modified scan settings.
No. Item Description
No. Item Description
1 Output name Assign a document name to scanned images. When multiple
images are saved in the same folder, a three-digit incrementing
number such as Scan_001, Scan_002... is appended to the end of
the file name. Up to 16 characters can be entered.
2 File format Specify the image file format.
Value: BMP, JPEG, PNG, TIFF, PDF
Note In Scan to PDF, all images are saved in PDF format.
1
4
5
2
3
2-47
Preparation
3Quality Set the image quality if File format is JPEG. The higher quality
becomes the lower compression. This is disabled for non-JPEG
format.
Value: 1 to 100
Note Non-numeric characters cannot be entered. If entered
number is beyond range, the max/min value will be restored.
4 Preferences Displays the TWAIN settings screen. For details, refer to TWAIN
Settings on page 2-45.
5 OK/Cancel/Apply Clicking OK exits the Quick Scan Settings after applying the
modified scan settings.
Clicking Cancel exit s the Quick Scan Settings without applying the
modified scan settings.
Clicking Apply applies the modified scan settings without exiting
the Quick Scan Settings.
No. Item Description
2-48
Preparation
Configuration
The Configuration is a function of KYOCERA Client Tool. The default settings of the machine can be changed and the
messages that appear in the Status Monitor can be set.
Accessing the Configuration
Follow these steps to display the Configuration on the desktop.
1Start KYOCERA Client Tool as explained in Accessing KYOCERA Client Tool on
page 2-26.
2Click Configuration on the Device tab. The Configuration opens.
Note For the detailed functions of the Configuration, refer to KYOCERA Client Tool User Guide.
2-49
Preparation
Configuration Screen
General
8
4
7
2
16
3
5
No. Item Description Reference
Page
1 Device Defaults Configure overall machine operation. 2-50
2Copy Configure settings for copying functions. 2-52
3FAX Configure settings for fax functions.
Note This setting only appears on the FS-1120MFP, FS-1125MFP,
FS-1320MFP and FS-1325MFP.
2-53
4 Communication Configure network settings. 2-55
5SNMP Traps Configure SNMP trap settings. 2-56
6 Status Monitor Configure settings for the Status Monitor. 2-57
7 OK/Cancel/Apply Clicking OK exits the Configuration after applying the modified machine
settings.
Clicking Cancel exits the Configuration without applying the modified
machine settings.
Clicking Apply applies the modified machine settings without exiting the
Configuration.
Note When clicking OK or Apply to apply the settings, the disconnection
error may occur if the System Menu is open in the message display of the
machine’s operation panel.
—
8— Close the Configuration. —
2-50
Preparation
Device Defaults Tab
1 2
3
4
5
7
8
9
11
14
12
10
6
13 15
16
No. Item Description
1 Power off timer Select the length of time before the machine shuts off automatically when not in use.
The default preset time is 1 hour.
Value: 1 to 6 hours, 9 hours, 12 hours, 1 day to 1 week
Also, selects whether or not to turn the power off automatically when the USB is
connected, when the Network is connected and when the FAX is installed.
Note FAX is installed only appears on the FS-1120MFP, FS-11 25MFP, FS-1320MFP
and FS-1325MFP. If the optional Fax kit is installed, note that turning the machine off at
the main power switch disables fax transmission and reception.
Network is connected only appears on the FS-1025MFP, FS-1125MFP and
FS-1325MFP.
2 Auto sleep Set the sleep timer for the machine to go into sleep mode when not in use. The default
preset time is 1 minute.
Value: 1 to 240 minutes (1 minute increments)
3Quiet mode Turn on Quiet Mode. Refer to Quiet Mode on page 1-4.
4Units Select Inches or Millimeters for the unit for paper dimensions.
5 Print density Adjust density using 5 levels.
Value: Light, Medium light, Normal, Medium dark, Dark
2-51
Preparation
6 Panel options Opens Panel options screen.
• D efault screen: Select the screen appearing right af ter
start-up (default screen).
Note To enable the change immediately, turn the
machine OFF and then ON. Otherwise wait until the
machine once enters the sleep and then resumes.
• Language: Select the language displayed on the
message display.
• Reset panel: If no jobs are run for a certain period of
time, automatically reset settings and return to the
default setting. If you select On for Reset panel , set the
amount of time to wait before Reset panel.
7 Auto error clear Enable auto error clear. If an error occurs during processing, processing stops to wait
for the next step to be taken by the user. In the auto error clear mode, automatically
clear the error after a set amount of time elapses.
If you select On for auto error clear, set the amount of time to wait before automatically
clearing errors.
Value: 5 to 495 seconds (every five seconds)
8 Form feed timeout When receiving print data from the computer , the machine may sometimes wait if there
is no information signaling that the last page does not have any more data to be
printed. When the preset timeout passes, the machine automatically prints the
documents. The options are between 5 and 495 seconds.
Value: 5 to 495 seconds (every five seconds)
9 Paper size Set the default paper size to load in the cassette.
Value: Letter, Legal, Statement, Executive, A4, A5, A6, Folio, B5 (JIS), B5 (ISO),
Oficio II, 216 × 340 mm, 16K, Custom size
When a Custom size is selected, the Custom Paper size screen appears.
T ype or select values for Width and Length. If the Width or
Length value exceeds the allowable limit, it automatically
adjusts to the limit after OK is clicked.
10 Original size Set the default original size to be scanned.
Value: Letter, Legal, Statement, Executive, A4, A5, A6, Folio, B5 (JIS), B5 (ISO),
Oficio II, 216 × 340 mm, 16K, Custom size
When a Custom size is selected, the Custom Original size screen appears.
T ype or select values for Width and Length. If the Width or
Length value exceeds the allowable limit, it automatically
adjusts to the limit after OK is clicked.
11 Original image Set the default image quality.
Value: Text + Photo, Photo, Text, Text + High resolution photo
12 Media type Set the default media type to load in the cassette.
Value: Plain, Preprinted, Labels, Bond, Recycled, Vellum (60 to 64 g/m²), Rough,
Letterhead, Color, Prepunched, Envelope, Cardstock, Thick (90 to 220 g/m²), High
quality, Custom 1-8
When Custom 1-8 is selected, the Custom name and Duplex enabled appear.
No. Item Description
2-52
Preparation
Copy Tab
13 Custom name Change names for Custom 1-8. Selecting media type, the name after change will be
displayed.
14 Paper weight Select weight for each media type. For details, refer to Paper Type on page 2-12.
Value: Light, Normal 1, Normal 2, Normal 3, Heavy 1, Heavy 2, Heavy 3
15 Duplex For Custom 1-8, settings for duplex printing can be changed.
Value: On, Off
Note This setting only appears on the FS-1025MFP, FS-1125MFP and FS-1325MFP.
16 Save Save the Paper weight, Custom name and Duplex settings that are set for Custom
1-8.
No. Item Description
13
46
5
7
2
No. Item Description
1Collate Select the defaults for Collate.
2Orientation Set the original orientation defaults.
Value: Top edge top, Top edge left
3EcoPrint Select the EcoPrint default.
4 Combine Set the default value for the layout for Combine.
Value: (2 Pages) Left to right, Top to bottom, Right to left
(4 Pages) Right then down, Down then right, Left then down, Down then left
5 Binding in finishing Set the binding direction selection when doing duplex copies.
Value: Left / Right, Top
Note This setting only appears on the FS-1025MFP, FS-1125MFP and FS-1325MFP.
6Zoom Select the default zoom setting.
Value: Auto, 100%
2-53
Preparation
FAX Tab
7 Density Set the default value for the copy density.
Value: Lighter (-3), Lighter (-2), Lighter (-1), Normal, Darker (+1), Darker (+2),
Darker (+3)
Note The FAX tab only appears for the FS-1120MFP, FS-1125MFP, FS-1320MFP and FS-1325MFP.
No. Item Description
1 7
3
16
2
4
9
17 20
21
11
613
10
15
5
8
14
18
19
22
12
No. Item Description
1Name Register the local fax name printed on the fax on the receiving system. Up to 32
characters can be entered.
2 Number Register the local fax number printed on the fax on the receiving system. Up to 32
characters can be entered.
3 TX start speed Set the TX start speed.
Value: 33600 bps, 14400 bps, 9600 bps
4ECM TX Set whether ECM TX is performed.
2-54
Preparation
5 Scan preferences Opens Scan and Print preferences screen.
6 Print preferences • Resolution: Select fineness of images when sending
fax.
Value: 200 × 100 dpi Normal, 200 × 200 dpi Fine,
200 × 400 dpi Super fine
• Density: Adjust density using 7 levels when sending
fax.
Value: Lighter (-3), Lighter (-2), Lighter (-1), Normal,
Darker (+1), Darker (+2), Darker (+3)
• Duplex: Performs duplex printing if a fax of multiple
pages are received when printing a fax.
Value: Off, On
Note Duplex only appears on the FS-1125MFP and
FS-1325MFP.
7 Transmit Terminal ID
(TTI) Select whether or not to print the local fax information on the fax on the receiving
system.
8 Volume control Opens Volume control screen.
• Speaker: Adjust the volume of the speaker.
Value: 0 - 5
• Monitor: Adjust the volume of the monitor.
Value: 0 - 5
For details on volume, refer to Sound on page 7-25.
9 Dialing mode Select the dialing mode according to the line type.
Note This setting does not appear in some regions.
10 Number of retries The number of automatic retry times can be changed.
Value: 0 - 14
11 RX date and time Reception date/time function adds the reception date/time, sender information and
number of pages on the top of each page when the message is printed out.
12 RX settings Select the reception mode.
Value: Auto (Normal), Auto (DRD)
Note DRD reception mode is only available for Australia and New Zealand. This setting
does not appear in other regions.
13 RX start speed Set the RX start speed.
Value: 33600 bps, 14400 bps, 9600 bps
14 ECM RX Set whether ECM RX is performed.
15 Number of rings The number of rings until the machine answers a call can be changed as needed.
Value: 1 - 15
16 Forwarding Set whether to forward the received faxes.
17 FAX number Register a forwarding destination. Up to 64 characters can be entered.
18 TX start speed Set the TX start speed when forwarding.
Value: 33600 bps, 14400 bps, 9600 bps
19 ECM Set the ECM when forwarding.
20 Forward time setting Register the start time and end time between which forwarding is enabled.
No. Item Description
2-55
Preparation
Communication Tab
21 Print You can set whether the machine should print received originals when forwarding
them.
22 Notification Opens Notification screen.
Set the settings related to fax reports.
• Transmission (TX)
Notification: Each time you send a fax, you can print a
report to confirm whether the fax was sent successfully.
Value: Off, On, Error only
Attach copy of TX: When this is selected, you can
print the transmitted image in the send result report.
TX report: When this is selected, the administration
report is printed after every 50 fax transmissions.
• Receiving (RX)
Notification: Each time you receive a fax, you can print
a report to confirm whether the fax was received
successfully.
Value: Off, On, Error only
RX report: When this is selected, the administration
report is printed after every 50 fax receptions.
Note The Communication tab only appears for the FS-1025MFP, FS-1125MFP and FS-1325MFP.
No. Item Description
1
2
4
3
2-56
Preparation
SNMP Traps Tab
No. Item Description
1 Host name Enter the host name of the machine.
MAX characters: 16
2 LAN interface Select the type of LAN interface installed on the machine.
You can also select check boxes for available port types that the machine uses for
communication: LPD setting, Raw port, WSD print.
Value: Auto, 10Base-half, 10Base-full, 100Base-half, 100Base-full
3 TCP/IP Select the check box to enable the DHCP protocol. Enter the IP address, subnet
mask, and Default gateway values.
4SNMP Select the check box to enable the SNMP protocol, and then select SNMP protocol
options. The SNMP protocol is used for providing and transferring management
information within the network environment. Read community and W r ite community
can have up to 16 characters. The default community is public. Type sysContact,
sysName, and sysLocation information up to 32 characters. Select Enable
authentication to activate machine authentication.
Note The SNMP Traps tab only appears for the FS-1025MFP, FS-1125MFP and FS-1325MFP connected by
network connection.
1
No. Item Description
1 Trap Recipient You can select SNMP trap settings for 1 or 2 IP addresses.
Should an error occur, such as Add paper, the machine automatically generates a
trap. The trap sends an error message to one or two predetermined trap recipients.
The trap server is the SNMP trap packet receiver which runs in the application. The
default community is public.
For each IP address, select the Trap Recipient check box, type the name of the trap
community and IP address, and select from available events.
2-57
Preparation
Status Monitor Tab
1
2
3
4
5
6
No. Item Description
1 Set toner level alert Select to create an alert when the toner starts running low, and then select a
percentage between 0 and 100. If the toner level goes below this percentage, an alert
icon is displayed on the Supplies tab at the bottom of KYOCERA Client Tool screen.
2 Enable event
notification Select to activate the notification feature for selected machine events. When selected,
notification options are available.
3 Enable pop-up
notification When selected, a pop-up message appears in the lower right corner of the screen for
each selected event as it occurs.
4Events list Select one or more events for the notification. To select all events, select Events.
5 Sound file With one or more events selected, select to enable sound notification. Type the
location of a sound file (.WAV), or click Browse to find a sound file located on your
computer. You can press the arrow button to hear the selected sound.
6 Use Text to Speech With one or more events selected, select and type your preferred text. The Microsoft
Text to Speech utility reads the text and plays it in a spoken voice. You can press the
arrow button to hear the selected text.
2-58
Preparation
Printing the Status Page
You can print the Status Page to check the current settings.
1Press [Menu].
2Press [▲] or [▼] to select System Menu.
3Press [OK].
4Press [▲] or [▼] to select Report.
5Press [OK].
6Press [▲] or [▼] to select Status Page.
7Press [OK].
8Press [▲] or [▼] to select Yes.
9Press [OK]. Printing starts.
Menu
b
System Menu
System Menu
b
Report
Report
b
Status Page
Status Page
b
Yes
3-1
3Copying
This chapter explains the following topics:
Basic Operation...................................................................................................................................................... 3-2
Manual Duplex....... ... ................ .... ... ... ... .... ... ................ ... ... .... ... ... ... ................. ... ... ... ... .......................................... 3-3
Using Programs .... ... .... ... ... ... ... ................. ... ... ... .... ... ... ................ ... .... ... ... ... .... ................ ...................................... 3-5
Copying Functions................................................................................................................................................. 3-6
ID Card Copy ........................................................................................................................................................ 3-13
3-2
Copying
Basic Operation
Follow the steps as below for basic copying.
1Press [Copy].
2Place the originals. For details, refer to Loading Originals on page 2-18.
If the originals are curled at a front edge, straighten them prior to loading.
3If a program is set, press the program key ([Program 1] - [Program 3]) in which the
program is registered.
4Enter the number of copies.
Use the numeric keys, [▲] or [▼] to enter the copy quantity.
Note For details on functions that are registered in programs, refer to Using
Programs on page 3-5.
Ready to copy.
Copies 05
3-3
Copying
5Adjust density using 7 levels (Lighter -3 to Darker +3).
Press [Density], and press [▲] or [▼] to select your desired density. Press [OK].
6Select the copier’s functions to use.
Press [Menu]. Copy functions can be selected. Press [▲] or [▼] to select the copier’s
functions to use.
7Press [Start] to start copying.
Manual Duplex
To copy on both sides of the paper, use Manual Duplex.
What do you want to do? Reference Page
Collate the output documents in page order. Refer to Collate on page 3-6.
Copy on both sides of the paper. Refer to Duplex on page 3-6.
Reduce or enlarge the original. Refer to Zoom on page 3-7.
Combine 2 or 4 originals into 1 sheet. Refer to Combine on page 3-9.
Specify the original size. Refer to Original Size on
page 3-10.
Specify the original orientation to scan in the correct
direction. Refer to Original Orientation on
page 3-11.
Select original image type for best results. Refer to Original Image on
page 3-12.
Save toner when printing. Refer to EcoPrint on page 3-12.
Note To return changed copy functions to the default state, press [Stop/Reset].
Density
b
Normal 0
Menu
b
Zoom
3-4
Copying
1Select copy functions and place the front-side original (or odd numbered page) as
explained in Basic Operation on page 3-2.
2Press [Start]. The front side is copied.
3Retrieve the paper from the inner tray. If copying on multiple sheets, fan through the sheets
to separate them prior to loading.
If the paper is curled at an edge, straighten it prior to reloading.
4Copy the back side (or even numbered page). Load the paper as shown.
Long Edge Binding Short Edge Binding
(Finished)
(Finished)
3-5
Copying
5Place the back-side original (or even numbered page). For details, refer to Loading
Originals on page 2-18.
6Press [Start]. The back side is copied, and duplex copying is completed.
Using Programs
If there are settings that you frequently change from the default state, register the settings in a program. You can simply
select the program number as needed to recall those functions.
Copy functions can be registered in three programs.
The programs below have been preregistered. The registered contents can be re-registered for easier use in your
environment.
Item Program1 Program2 Program3
Original size A4 (Letter) A4 (Letter) A4 (Letter)
Original image Text Text+Photo (300 dpi) Photo
Copies 1 1 1
Collate On On On
Original orientation Top Edge Top Top Edge Top Top Edge Top
Zoom Auto Auto Auto
Density Darker (+3) Lighter (-2) Normal (0)
EcoPrint Off On Off
Duplex*
* Duplex can only be set on the FS-1025MFP, FS-1125MFP and FS-1325MFP.
Off On (Binding Left/Right) Off
Combine Off 2in1 (Left to right) Off
Note Refer to Program Settings on page 2-32 for registering programs.
Refer to Basic Operation on page 3-2 for recalling programs.
3-6
Copying
Copying Functions
Collate
Offset the output by page or set.
1Press [Menu].
2Press [▲] or [▼] to select Collate.
3Press [OK].
4Press [▲] or [▼] to select On.
5Press [OK].
Duplex
Produce two-sided copies.
1Press [Menu].
2Press [▲] or [▼] to select Duplex.
3Press [OK].
4Press [▲] or [▼] to select 1-sided>>2-sided.
Note Copy functions can also be set from KYOCERA Client Tool. For details, refer to Machine Settings on
page 2-26.
Collate
b
On
Note Duplex copying can be performed on the FS-1025MFP, FS-1125MFP and FS-1325MFP. To perform Manual
Duplex copying on the FS-1120MFP and FS-1320MFP, refer to Manual Duplex on page 3-3.
Select the orientation of the original document top edge to scan correct direction.
Top Edge Top Top Edge Left
Duplex
b
1-sided>>2-sided
3-7
Copying
5Press [OK].
6Press [▲] or [▼] to select Top Edge Top or Top Edge Left.
7Press [OK].
Zoom
Adjust the magnification to reduce or enlarge the original image. The following zoom options are available.
Setting 100% or Auto
1Press [Menu].
2Press [▲] or [▼] to select Zoom.
3Press [OK].
4Press [▲] or [▼] to select 100% or Auto.
5Press [OK].
Orig. Orientation
b
Top Edge Top
Item Description
100% Copies at full size.
Auto Adjusts the image to match the paper size.
Standard Zoom Adjusts the image to match present sizes.
Metric Models: 400%, 200%, 141% A5 >> A4, 115% B5 >> A4, 100%, 90% FOL >> A4, 86% A4 >>
B5, 70% A4 >> A5, 50%, 25%, Others (129% STMT >> LTR, 78% LGL >> LTR, 64% LTR >> STMT)
Inch Models: 400%, 200%, 129% STMT >> LTR, 100%, 78% LGL >> LTR, 64% LTR >> STMT,
50%, 25%, Others (141% A5 >> A4, 115% B5 >> A4, 90% FOL >> A4, 86% A4 >> B5, 70% A4 >>
A5)
Zoom Entry Specify the image size in 1% increment between 25% - 400% of the original.
Zoom Entry (25% - 400%)
A4: 140%
A5
A5: 70%
A4
Zoom
b
Auto
3-8
Copying
Setting Standard Zoom
1Press [Menu].
2Press [▲] or [▼] to select Zoom.
3Press [OK].
4Press [▲] or [▼] to select Standard Zoom.
5Press [OK].
6Press [▲] or [▼] to select the desired magnification, and then press [OK].
7If you select Others, press [▲] or [▼] from the displayed magnification to select the
desired magnification, and then press [OK].
Setting Zoom Entry
1Press [Menu].
2Press [▲] or [▼] to select Zoom.
3Press [OK].
4Press [▲] or [▼] to select Zoom Entry.
5Press [OK].
6Use the numeric keys to enter the any magnification, and then press [OK]. A magnification
from 25% to 400% can be selected.
Zoom
b
Standard Zoom
Standard Zoom
b
100%
Zoom
b
Zoom Entry
Zoom Entry
b
(25 - 400) %
200
3-9
Copying
Combine
Combine 2 or 4 original sheets into 1 copied page. You can select the page layout.
Setting 2 in 1
1Press [Menu].
2Press [▲] or [▼] to select Combine.
3Press [OK].
4Press [▲] or [▼] to select 2 in 1.
5Press [OK].
6Press [▲] or [▼] to select L to R/T to B or R to L.
7Press [OK].
Page layout
2 in 1 L to R/T to B R to L
4 in 1 Right then Down Down then Right Left then Down Down then Left
Original Orientation
Select the orientation of the original
document top edge to scan correct
direction.
Top Edge Top Top Edge Left
Combine
b
2 in 1
2 in 1
b
L to R/T to B
3-10
Copying
8Press [▲] or [▼] to select Top Edge Top or Top Edge Left.
9Press [OK].
Setting 4 in 1
1Press [Menu].
2Press [▲] or [▼] to select Combine.
3Press [OK].
4Press [▲] or [▼] to select 4 in 1.
5Press [OK].
6Press [▲] or [▼] to select Right then Down, Down then Right, Left then Down or
Down then Left.
7Press [OK].
8Press [▲] or [▼] to select Top Edge Top or Top Edge Left.
9Press [OK].
Original Size
Specify the size of originals being scanned.
The following options are available.
Orig. Orientation
b
Top Edge Top
Combine
b
4 in 1
4 in 1
b
Right then Down
Orig. Orientation
b
Top Edge Top
Model Original Size
Metric Models A4, A5, A6, B5, Folio, Letter, Legal, S tatement, Executive, Oficio II, 216 × 340 mm, 16K, Others (ISO
B5, Custom)
Inch Models Letter, Legal, S tatement, Executive, Oficio II, 216 × 340 mm, A4, A5, A6, B5, Folio, 16K, Others (ISO
B5, Custom)
Note To use Custom, register the custom size of the original. For detail, refer to Configuration on page 2-48.
3-11
Copying
1Press [Menu].
2Press [▲] or [▼] to select Original Size.
3Press [OK].
4Press [▲] or [▼] to select the desired original size and then press [OK].
5If you selected Others, press [▲] or [▼] to select ISO B5 or Custom, and then press
[OK].
Original Orientation
Select the orientation of the original document top edge to scan correct direction.
To use any of the following functions, the document's original orientation must be set.
•Combine
•Duplex
1Press [Menu].
2Press [▲] or [▼] to select Orig. Orientation.
3Press [OK].
4Press [▲] or [▼] to select Top Edge Top or Top Edge Left.
5Press [OK].
Original Size
b
A4
Top Edge Top Top Edge Left
Orig.Orientation
b
Top Edge Top
3-12
Copying
Original Image
Select image quality suited to the type of original.
1Press [Menu].
2Press [▲] or [▼] to select Original Image.
3Press [OK].
4Press [▲] or [▼] to select the desired original image.
5Press [OK].
EcoPrint
Use EcoPrint to save toner when printing. Use this function for test copies or any other occasion when high quality print is
not required.
1Press [Menu].
2Press [▲] or [▼] to select EcoPrint.
3Press [OK].
4Press [▲] or [▼] to select On.
5Press [OK].
Item Description
Text+Photo (High) Best when you want good reproduction of fine text and lines in originals which contain a mixture of
text and photos.
Text+Photo Best for originals which contain a mixture of text and photos.
Photo Best for photographs.
Text Sharply renders pencil text and fine lines.
Original Image
b
Text+Photo
EcoPrint
b
On
3-13
Copying
ID Card Copy
Use to copy the front and back sides of a license or other ID card on one sheet of paper.
1Press [ID Card Copy]. Scan the front page. appears.
2Place the original. Align with the ID Card marks on the Original Size Indicator Plates.
For details, refer to Loading Originals on page 2-18.
3Enter the number of copies. (Refer to Basic Operation on page 3-2.)
4Adjust density. (Refer to Basic Operation on page 3-2.)
5Press [Start]. One side of the card is scanned.
6Turn the original over. Align with the ID Card marks on the Original Size Indicator Plates.
7Press [Start]. The front and back sides of the card are copied on one sheet of paper.
Scan the front page.
Copies 01
ID Card
ID Card
Scan the back page.
Press Start Key.
ID Card
ID Card
3-14
Copying
4-1
4Printing
This chapter explains the following topics:
Printing from Application Software...................................................................................................................... 4-2
About GX Driver ................................................................................................................ ..................................... 4-2
Manual Feed (FS-1025MFP, FS-1125MFP and FS-1325MFP).............................................................................. 4-3
Manual Duplex (FS-1120MFP and FS-1320MFP only)............... ... .... ... ... ... .... ................ ... ... ... .... ... ... ................... 4-4
Print Box ................................................................................................................................................................. 4-6
Changing the Default Printer Driver Settings (Windows 7 for example)........................................................... 4-8
4-2
Printing
Printing from Application Software
The steps required to print a document created with an application are explained below. You can select the printing paper
size.
1Load the paper required into the cassette.
2From the application File menu, select Print. The Print screen appears.
3Click the drop-down list of printer names. All the installed printers are listed. Click the name
of the printer.
4Use Number of copies to enter the number of copies required. Up to 999 copies can be
printed. For Microsoft Word, we recommend that you click Options and specify Use
printer settings for the Default tray.
5To start printing, click OK.
About GX Driver
GX Driver consists of the following tabs.
Note You can also select the various settings by clicking Properties to open the Properties screen. Refer to About
GX Driver.
Tabs Description
Quick Print Use this tab to define basic print options into group profiles that
can be accessed quickly and easily.
Basic Use this tab to select the page size and orientation. The paper
source is also selected.
Layout Use to create multiple pages on a single sheet of paper. Also
contains the scaling option.
Imaging Select this tab to change the print quality and graphic settings.
Job Use to save a print job in a Print Box. Refer to Print Box on
page 4-6.
Advanced Use to set up and add watermarks to your output.
4-3
Printing
Manual Feed (FS-1025MFP, FS-1125MFP and FS-1325MFP)
[OK] can be pressed on the operation panel to feed and print on one sheet of paper. This is convenient when loading one
envelope at a time in the Manual Feed tray.
1Ensure Manual feed is selected as the Source in the Properties screen.
2Use Number of copies to enter the number of copies required.
3Select OK to return to the Print screen and select OK.
4Load the paper in the Manual Feed tray for the machine and press [OK]. One sheet is
printed.
5Repeat step 4 until all pages are printed.
Note If Auto source selection has been selected, paper is automatically fed from
the Manual Feed tray. If there is no paper in the Manual Feed tray, paper is
automatically fed from the cassette.
4-4
Printing
Manual Duplex (FS-1120MFP and FS-1320MFP only)
To print on both sides of the paper, use Manual Duplex. The even pages are printed first and then reloaded to print the odd
pages. An instruction sheet is available to assist with loading the sheets in the correct orientation and order.
1Select Print on both sides (manual duplex).
Select Flip on long edge if the binding will be on the long edge or Flip on short edge if
the binding will be on the short edge. Select P rint manual du plex instr uct ions to receive
the instruction sheet.
2Select OK to return to the Print screen and select OK to start printing. A Manual Duplex
Instruction message box displays. The even pages are printed including the instruction
sheet.
3Remove all the even pages (including the instruction sheet) from the inner tray, fan through
the sheets to separate them prior to loading.
If the paper is curled at an edge, straighten it prior to reloading.
Note Ensure Print manual duplex instructions is selected to receive the instruction sheet. Continue to use the
sheet until you are familiar with this feature.
Note Instructions for manual duplex will be printed on the instruction sheet.
4-5
Printing
4Load the even pages printed into the cassette with the instruction sheet facing down and
the arrows pointing toward the machine.
5Select OK in the Manual Duplex Instruction message box of the printer driver screen. All
the odd pages will be printed.
Note If the paper is considerably curled in one direction, roll the paper in the opposite
direction to counteract the curl. If this will not cancel the curl satisfactorily, try to
reduce the number of sheets loaded in the cassette to the maximum of 100.
Manual Duplex Instructions
Long Edge Binding
Manual Duplex Instructions
Short Edge Binding
Long Edge Binding Short Edge Binding
(Finished)
(Finished)
4-6
Printing
Print Box
A print job can be saved in Print Box in the computer and printed from the machine when needed. Use the machine's
operation panel to print the print job stored in a Print Box.
The four possible selections for the Print Box are the Default box and Boxes 1 - 3.
Saving to a Print Box
Save a print job to a Print Box.
1From the application File menu, select Print. The Print screen appears.
2Click Properties. The Properties screen appears.
3Select Job tab.
4Select Job storage then select the Print Box where the print job should be stored from the
Default, Box 1, Box 2 or Box 3.
5Set the job name for the print job.
6Select OK to return to the Print screen and click OK to start storing.
Note The folder to be used for Boxes 1 - 3 can be set in the Preset Tool. Refer to Program Settings on page 2-32.
Note The Default box can only be used from a machine connected by USB.
Settings Filename
Application define and
Don’t use application
name
<Document name> <month><day><year>
<hour><minutes><seconds>.prn
Example: PrintBox.docx
Filename: PrintBox 040112 030201.prn
Application define <Application name> <month><day><year>
<hour><minutes><seconds>.prn
Example: PrintBox.docx
Filename: Microsoft Word 040112 030201.prn
Custom and Use job
name + date and time <Custom name> <month><day><year>
<hour><minutes><seconds>.prn
Example: Custom name is Print_A.
Filename: Print_A 040112 030201.prn
Custom and Replace
existing file <Custom name>.prn
Example: Custom name is Print_A.
Filename: Print_A.prn
Note Any stored job with the same name will be overwritten.
4-7
Printing
Printing from Print Box
Print a print job saved in a Print Box.
1Press [Print Box].
2Press [Program 1] to [Program 3] to select the Print Box.
If a Print Box is not selected, the jobs stored in Default box are printed.
The following boxes are pre-registered in the Print Box Program.
Program 1: Box 1
Program 2: Box 2
Program 3: Box 3
3Press [Start] to start printing.
Note The Default box can only be used from a machine connected by USB.
All print jobs saved in the selected Print Box are printed.
KYOCERA Client Tool must be running on the computer from which printing from Print Box is executed. Refer to
Machine Settings on page 2-26.
After being printed, the print jobs in the Print Box are deleted.
Note When Program 1, 2 or 3 is selected, the Name set in the Preset Tool is
displayed. Also, the folders for Boxes 1 - 3 can be changed in the Preset Tool. Refer
to Program Settings on page 2-32 for registering programs.
Ready to print.
Folder 1
4-8
Printing
Changing the Default Printer Driver Settings (Windows 7 for example)
The default printer driver settings can be changed. By selecting frequently used settings, you can omit steps when printing.
The procedure is as follows.
1Click the start button, and then click Devices and Printers.
2Right-click the printer driver icon of the machine, and click the Printer properties menu of
the printer driver.
3Click the Printing Preferences button on the General tab.
4Select the default settings and click the OK button.
For the settings, refer to Printer Driver User Guide.
5-1
5 Scanning
This chapter explains the following topics:
Push Scan............................................................................................................................................................... 5-2
Using Programs .... ... .... ... ... ... ... ................. ... ... ... .... ... ... ................ ... .... ... ... ... .... ................ ...................................... 5-3
Quick Scan (Scan to PDF/Scan to Email/Scan to Folder) .................................................................................. 5-4
Scanning using TWAIN/WIA........... ... ................ .... ... ... ... ... .... ... ................ ... .... ... ... ... ... .... ... ................................... 5-5
5-2
Scanning
Push Scan
It is easy to scan from the operation panel on the machine. Push Scan performs scanning with the following settings.
1Press [Scan].
2Place the originals. For details, refer to Loading Originals on page 2-18.
Item Value
Original size If unit setting is inch: Letter
If unit setting is mm: A4
For details on unit setting, refer to Configuration on page 2-48.
Feed method Auto
Resolution 300 × 300 dpi
Reverse image Unchecked
Sharpen None
Original quality Text + Photo
Scan color Full color
Density Normal (0)
Output name Scan
File format PDF
Destination folder For Windows Vista/Windows 7: C:\Users\<user >\My Documents
For Windows XP: C:\Documents and Settings\<user>\My Documents
Note The Program is used to change the settings. Refer to Using Programs on page 5-3.
When using Push Scan, KYOCERA Client Tool must be running on the computer. Refer to Accessing KYOCERA
Client Tool on page 2-26.
When using Push Scan, the machine must be connected by USB.
5-3
Scanning
3If a program is set, press the program key ([Program 1] - [Program 3]) in which the
program is registered.
4Press [Start] to start scanning.
Using Programs
If there are settings that you frequently change from the default state, register the settings in a program. You can simply
select the program number as needed to recall those functions.
Scan functions can be registered in three programs.
The programs below have been preregistered. The registered contents can be re-registered for easier use in your
environment.
Note For details on functions that are registered in programs, refer to Using
Programs on page 5-3.
Item Program1 Program2 Program3
Name Folder 1 Folder 2 Folder 3
Original size A4 (Letter) A4 (Letter) A4 (Letter)
Original image Text Text + Photo Photo
Reverse image Off Off Off
Sharpen Low Low Low
Scan color Full color Full color Full color
Density Normal (0) Normal (0) Normal (0)
Resolution 300 × 300 dpi 300 × 300 dpi 300 × 300 dpi
Output name Scan Scan Scan
File format PDF PDF PDF
Quality———
Destination folder C:\User\<user>\My Documents (Windows Vista/Windows 7)
C:\Document and Settings\<user>\My Documents (Windows XP)
Note For details on program registration and the various functions, refer to Program Settings on page 2-32.
Refer to Push Scan on page 5-2 for recalling programs.
5-4
Scanning
Quick Scan (Scan to PDF/Scan to Email/Scan to Folder)
Execute scanning from KYOCERA Client Tool. With Quick Scan, the following 3 types of scan are possible.
Scan to PDF: Saves the scanned image in PDF format. The folder is specified after scanning.
Scan to Email: Attaches the scanned image to a new E-mail message.
Scan to Folder: Saves the scanned image to a specified folder.
1Place the originals. For details, refer to Loading Originals on page 2-18.
2Start KYOCERA Client Tool as explained in Accessing KYOCERA Client Tool on
page 2-26.
3Click Scan to PDF, Scan to Email or Scan to Folder icon on the Scan tab.
4Scan to PDF
Scanning begins. When scanning finishes, the Save PDF File As dialog appears. Specify
the PDF file name and the folder in which the image will be saved.
Scan to Email
Scanning begins. When scanning finishes, the mailer starts and the scanned image is
attached. Enter the address, subject and message, and then send.
Scan to Folder
The Browse for Folder dialog appears. Specify the folder in which the image will be
saved, and click [OK]. Scanning begins.
Note The folder in which the scanned image is saved and the file format can be set in advance in KYOCERA Client
Tool. Refer to Quick Scan/TWAIN Settings on page 2-45.
When using Quick Scan, the machine must be connected by USB.
5-5
Scanning
Scanning using TWAIN/WIA
This section explains how to scan an original using TWAIN/WIA.
The procedure for scanning using the TWAIN driver is explained as an example. The WIA driver is used in the same way.
1Place the originals. For details, refer to Loading Originals on page 2-18.
2Activate the TWAIN compatible application.
3Select the machine using the application and display the TWAIN screen.
4Select scanning settings in the TWAIN screen that opens.
The settings that appear in the TWAIN screen are as follows.
Note For selecting the machine, see the Operation Guide or Help for each
application software.
No. Item Description
1Original size Sp ecify the size of originals being scanned. The sizes that can
be selected vary depending on the Feed method setting.
Value: (when the Feed method is Auto or Platen) Letter,
Statement, Executive, A4, A5, A6, B5 (JIS), B5 (ISO), 16K,
Custom
(when the Feed method is Document Processor) Letter,
Legal, Statement, Executive, A4, A5, A6, Folio, B5 (JIS),
B5 (ISO), Oficio II, 16K, 216 × 340 mm, Custom
Note Refer to Configuration on page 2-48 for selecting
Custom.
2 Feed method Select the original feed method.
Value: Auto, Document Processor, Platen
1
2
3
5 7
68
10
11
12 15
13 14
9
4
16
5-6
Scanning
3 Scan color Select the color mode setting.
Value: Monochrome, Grayscale, Full color
4 Resolution Select fineness of scanning resolution.
Value: 200 × 200 dpi, 300 × 300 dpi, 400 × 400 dpi,
600 × 600 dpi
5Sharpen Adjust the sharpness of the image.
Value: None, Low, Medium, High, Descreen (Blurs the
outlines and reduces the sharpness.)
6Original image Select original image type for best results.
Value: Text, Photo, Text+Photo
7 Density Select the density.
Value: -3 (Lighter) to 3 (Darker)
8 Reverse image When this is selected, the image color reverses.
9 Reset Reset the settings to the default value.
10 Preview area Displays a preview of the scanned image. The image can be
enlarged, rotated, trimmed, or moved.
11 Details list Displays a list of the settings.
12 Help Displays the Help screen.
13 Pre-Scan Acquires a preview image.
14 Scan Performs the scan and returns the image to the application.
15 Close Close the TWAIN screen.
16 About Displays the driver version number.
No. Item Description
6-1
6 Default Setting (System Menu)
This chapter explains the following topics:
Default Setting (System Menu) ............................................................................................................................. 6-2
Operation Method .... .... ... ................ ... ... .... ... ... ... ................ .... ... ... ... .... ... ................ ... ... .... ...................................... 6-2
System Menu Settings........................................................................................................................................... 6-3
Administrator ID..................................................................................................................................................... 6-6
6-2
Default Setting (System Menu)
Default Setting (System Menu)
Configure settings related to overall machine operation in the System Menu.
Operation Method
The System Menu is operated as follows:
1Press [Menu].
2Press [▲] or [▼] to select System Menu.
3Press [OK].
4Press [▲] or [▼] to display the desired menu.
5Use [▲] or [▼] or the numeric keys to change the setting.
6Press [OK]. The setting is registered. To exit, press [Menu].
Refer to System Menu Settings on the following page and configure as needed.
Note If the Administrator ID entry display appears, use the numeric keys to enter the
Administrator ID (4 digits) and press [OK]. The default setting is 2500 for the
FS-1025MFP, FS-1125MFP and FS-1325MFP, 2000 for the FS-1120MFP and
FS-1320MFP.
For details of Administrator ID, refer to Administrator ID on page 6-6.
Menu
b
System Menu
System Menu
b
Report
System Menu
b
Common Settings
The setting items successively
appear as [▲] or [▼] is pressed.
Common Settings
b
Language
When [OK] is pressed, the next setting
of the selected item appears. To return
to the previous display, press [Back].
Administrator ID
b
(0000 - 9999)
****
Language
b
*English
6-3
Default Setting (System Menu)
System Menu Settings
System Menu include;
Report
Print reports to check the machine settings and status. Default settings for printing the result reports can also be
configured.
Note For details on fax operation, refer to Fax Settings on page 7-24.
The System Menu contains some menus that can be set from a computer. Refer to Configuration on page 2-48.
Item Description Reference
Page
Report Print reports to check the machine settings and status. 6-3
Common Settings Configure overall machine operation. 6-4
Language Select the language displayed on the message display. 6-4
Default Screen Select the screen appearing right after start-up (default screen). 6-4
Sound*
* This setting only appears on the FS-1120MFP, FS-1125MFP, FS-1320MFP and FS-1325MFP.
Adjust the FAX speaker volume and monitor volume. For details, refer to
Sound on page 7-25.7-25
Display Bright. Set the brightness of the message display. 6-4
Original Size Specify the original size to be scanned. 6-4
Paper Settings Select paper size and media type for the cassette. 6-4
Date Settings* Set the date and time for the location where you use the machine. For
details, refer to Setting Date and Time on page 7-2.7-2
Timer Settings Configure settings related to time. 6-5
FAX Settings* Configure settings for fax functions. For details, refer to Fax Settings on
page 7-24.7-24
Administrator Change the Administrator ID. 6-6
Adjust/Maint. Adjust printing quality and conduct machine maintenance. 6-5
Service Settings
Item Description
Status Page Print the status page, allowing you to check the information including current settings.
To print, select Yes.
Network Status*
* This setting only appears on the FS-1025MFP, FS-1125MFP and FS-1325MFP.
Print the network status, allowing you to check the information including network interface
firmware version, network address and protocol.
To print, select Yes.
Admin Rpt Set.**
** This setting only appears on the FS-1120MFP, FS-1125MFP, FS-1320MFP and FS-1325MFP.
Configure settings for FAX reports. For details, refer to Fax Settings on page 7-24.
Result Rpt Set.**
6-4
Default Setting (System Menu)
Common Settings
Configures overall machine operation.
Language
Default Screen
Display Bright.
Original Size
Paper Settings
Item Description
Language Select the language displayed on the message display.
Item Description
Default Screen Select the screen appearing right after start-up (default screen).
Value: Copy, FAX, ID card Copy
Note FAX only appears on the FS-1120MFP, FS-1125MFP, FS-1320MFP and FS-1325MFP.
Item Description
Display Bright. Set the brightness of the message display.
Value: Darker -3, Darker -2, Darker -1, Normal 0, Lighter +1, Lighter +2,
Lighter +3
Item Description
Original Size Specify the original size to be scanned.
Value
Metric Models: A4, A5, A6, B5, Folio, Letter, Legal, Statement, Executive,
Oficio II, 216×340 mm, 16K, ISO B5, Custom
Inch Models: Letter, Legal, Statement, Executive, Oficio II, 216×340 mm, A4,
A5, A6, B5, Folio, 16K, ISO B5, Custom
Item Description
Paper Size Set the paper size to load in the cassette.
Value: A4, A5, A6, B5, 16K, ISO B5, Custom, Legal, Oficio II, 216×340 mm, Letter,
Executive, Statement, Folio
This can also be set from your computer. For details, refer to Configuration on page 2-48.
Media Type Set the media type to load in the cassette.
Value: Plain, Rough, Labels, Recycled, Preprinted, Bond, Vellum, Cardstock,
Color, Prepunched, Letterhead, Envelope, Thick, High quality, Custom 1 - 8
The names that were registered in KYOCERA Client Tool appear in Custom 1 - 8. For
details, refer to Machine Settings on p age 2-26.
This can also be set from your computer. For details, refer to Configuration on page 2-48.
6-5
Default Setting (System Menu)
Timer Settings
Adjustment and Maintenance
Adjust printing quality and conduct machine maintenance.
Service Settings
Note If the Administrator ID entry display appears, use the numeric keys to enter the Administrator ID (4 digits). The
default setting is 2500 for the FS-1025MFP, FS-1125MFP and FS-1325MFP, 2000 for the FS-1120MFP and
FS-1320MFP.
For details of Administrator ID, Administrator ID on page 6-6.
Item Description
Sleep Timer Auto Sleep automatically switches the machine into Sleep if left idle for a preset time. Set
amount of time before entering Sleep.
Value: 1 to 240 minutes (1 minute increments)
This can also be set from your computer. For details, refer to Configuration on page 2-48.
Auto Panel Reset If no jobs are run for a certain period of time, automatically reset settings and return to the
default setting. Set whether or not Auto Panel Reset is used, and the time until reset takes
place after the last job.
Value: Off, On (5 to 495 seconds (every five seconds))
Power Off Rule For each connection type (Network, FAX, USB Cable), set whether the power automatically
turns off when not used.
If you select On (the power automatically turns off), set the time in Power Off Timer which
appears next.
Value: Off, On
Network only appears on the FS-1025MFP, FS-1125MFP and FS-1325MFP.
FAX only appears on the FS-1120MFP, FS-1125MFP, FS-1320MFP and FS-1325MFP. If the
optional Fax kit is installed, note that turning the machine off at the main power switch
disables fax transmission and reception.
This can also be set from your computer. For details, refer to Configuration on page 2-48.
Power Off Timer The time until the power turns off can be set.
Value: 1 to 6 hours, 9 hours, 12 hours, or 1 day to 1 week
This can also be set from your computer. For details, refer to Configuration on page 2-48.
Err. Clear Timer If an error occurs during processing, processing stops to wait for the next step to be taken by
the user. In the Auto Error Clear mode, automatically clear the error af ter a set amount of time
elapses. For details, refer to Error Messages on page 9-8.
Value: Off, On (5 to 495 seconds (every five seconds))
Unusable Time Set the unusable time. For detail, refer to Unusable Time on page 7-35.
Note If the Administrator ID entry display appears, use the numeric keys to enter the Administrator ID (4 digits). The
default setting is 2500 for the FS-1025MFP, FS-1125MFP and FS-1325MFP, 2000 for the FS-1120MFP and
FS-1320MFP.
For details of Administrator ID, refer to Administrator ID on page 6-6.
Item Description
Maintenance Run this after replacing the Maintenance Kit.
New Developer Run this after replacing the Developer unit.
New Drum Run this after replacing the Drum unit.
FAX Country Code* For details, refer to Fax Settings on page 7-24.
FAX Call Set.* For details, refer to Fax Settings on page 7-24.
* This setting only appears on the FS-1120MFP, FS-1125MFP, FS-1320MFP and FS-1325MFP.
6-6
Default Setting (System Menu)
Administrator ID
To change the following settings in the System Menu, the Administrator ID must be entered.
•Date Settings (FS-1120MFP, FS-1125MFP, FS-1320MFP and FS-1325MFP)
•Timer Settings
•Administrator
•Adjust/Maint.
If the Administrator ID entry display appears, use the numeric keys to enter the Administrator ID (4 digits). The default
setting is 2500 for the FS-1025MFP, FS-1125MFP and FS-1325MFP, 2000 for the FS-1120MFP and FS-1320MFP.
Changing the Administrator ID
To change the Administrator ID, follow the steps below.
1Press [Menu].
2Press [▲] or [▼] to select System Menu.
3Press [OK].
4Press [▲] or [▼] to select Administrator.
5Press [OK].
6Use the numeric keys to enter the Administrator ID. The default setting is 2500 for the
FS-1025MFP, FS-1125MFP and FS-1325MFP, 2000 for the FS-1120MFP and
FS-1320MFP.
7Press [OK].
8Press [▲] or [▼] to select Administrator ID.
9Press [OK].
10Enter the new Administrator ID with the numeric keys.
11Press [OK].
12Enter the same Administrator ID to confirm.
13Press [OK]. The new Administrator ID is registered.
Administrator ID
b
(0000 - 9999)
****
Note It is recommended to periodically change the administrator ID regularly for your
security. You will be unable to change it if you forget your administrator ID.
Administrator ID
b
(0000 - 9999)
****
Administrator ID
b
(0000 - 9999)
****
Confirm Admin. ID
b
(0000 - 9999)
****
7-1
7 FAX Operations
This chapter explains the following topics:
Before Using the Fax Machine.............................................................................................................................. 7-2
Entering the Destination........................................................................................................................................ 7-7
Sending Faxes...................................................................................................................................................... 7-12
Receiving Faxes....... .... ... ... ... ................ .... ... ... ... .... ... ................ ... ... .... ... ... ... ................ .... .................................... 7-21
Printing Communication Reports....................................................................................................................... 7-23
Fax Settings..... ... ... ... .... ................ ... ... ... .... ... ... ................ ... .... ... ... ... .... ................ ... ... ... ........................................ 7-24
Sending Faxes from PC....................................................................................................................................... 7-37
7-2
FAX Operations
Before Using the F ax Machine
Configure the settings below.
Setting Date and Time
Set the local date and time at the place of installation.
When you send a fax using the transmission function, the date and time as set here will be printed in the header of the fax.
1Press [Menu].
2Press [▲] or [▼] to select System Menu.
3Press [OK].
4Press [▲] or [▼] to select Common Settings.
5Press [OK].
6Press [▲] or [▼] to select Date Settings.
7Press [OK].
8Use the numeric keys to enter the Administrator ID. The default setting is 2500 for the
FS-1025MFP, FS-1125MFP and FS-1325MFP, 2000 for the FS-1120MFP and
FS-1320MFP.
9Press [OK].
10Press [▲] or [▼] to select Date/Time.
11Press [OK].
12Enter the date and time with the numeric keys.
Enter the ‘year’ and press [OK]. The ‘month’ can then be entered. In the same way, enter
the ‘day’, ‘hour’, and ‘minute’. To move back, press [Back].
13Press [OK].
14Press [▲] or [▼] to select Date Format.
15Press [OK].
16Press [▲] or [▼] to select the display format of year, month, and date.
17Press [OK].
Note The following date formats are available.
•Month/Day/Year
•Day/Month/Year
•Year/Month/Day
Administrator ID
b
(0000 - 9999)
****
Date/Time
b
/ 3/ 3 10:00
2012
Date Format
b
Year/Month/Day
7-3
FAX Operations
Local FAX Information Entry
Register the local FAX information below.
TTI (Transmit Terminal Identification)
Select whether or not to print the local fax information on the fax on the receiving system.
1Press [Menu].
2Press [▲] or [▼] to select System Menu.
3Press [OK].
4Press [▲] or [▼] to select FAX.
5Press [OK].
6Press [▲] or [▼] to select Transmission.
7Press [OK].
8Press [▲] or [▼] to select TTI.
9Press [OK].
10Press [▲] or [▼] to select On or Off.
11Press [OK].
Local FAX Name
Register the local fax name printed on the fax on the receiving system.
1Press [Menu].
2Press [▲] or [▼] to select System Menu.
3Press [OK].
4Press [▲] or [▼] to select FAX.
5Press [OK].
6Press [▲] or [▼] to select Transmission.
7Press [OK].
8Press [▲] or [▼] to select Local FAX Name.
9Press [OK].
Note To have your fax number printed on the fax by the receiving machine, set TTI
to On.
TTI
b
On
7-4
FAX Operations
10Use the numeric keys to enter the local fax name.
11Press [OK].
Local FAX Number
Enter the local fax number to be printed on the fax on the receiving system.
1Press [Menu].
2Press [▲] or [▼] to select System Menu.
3Press [OK].
4Press [▲] or [▼] to select FAX.
5Press [OK].
6Press [▲] or [▼] to select Transmission.
7Press [OK].
8Press [▲] or [▼] to select Local FAX Number.
9Press [OK].
10Use the numeric keys to enter the local fax number.
11Press [OK].
FAX Dialing Mode
Select the dialing mode according to the line type.
1Press [Menu].
2Press [▲] or [▼] to select System Menu.
3Press [OK].
Note Refer to Character Entry Method on page 10-2 for details on entering
characters.
Local FAX Name
b
Sales department
Note Up to 20 digits can be entered as the local fax number.
Local FAX Number
b
0123456789
Note This setting does not appear in some regions.
7-5
FAX Operations
4Press [▲] or [▼] to select FAX.
5Press [OK].
6Press [▲] or [▼] to select Transmission.
7Press [OK].
8Press [▲] or [▼] to select FAX Dialing Mode.
9Press [OK].
10Press [▲] or [▼] to select Tone(DTMF) or Pulse(10pps).
11Press [OK].
ECM TX
Set whether ECM TX is performed. ECM is a communication mode specified by the ITU-T (International
Telecommunication Union) that retransmits data when an error occurs. Fax machines that have ECM mode check for
errors as they communicate, preventing distortion of the image due to noise on the line and other conditions.
1Press [Menu].
2Press [▲] or [▼] to select System Menu.
3Press [OK].
4Press [▲] or [▼] to select FAX.
5Press [OK].
6Press [▲] or [▼] to select Transmission.
7Press [OK].
8Press [▲] or [▼] to select ECM TX.
9Press [OK].
10Press [▲] or [▼] to select On or Off.
11Press [OK].
FAX Dialing Mode
b
Tone(DTMF)
Note When there is a large amount of noise on the line, communication may take slightly longer than when Off is
selected.
ECM TX
b
Off
7-6
FAX Operations
TX Start Speed
Set the TX Start Speed. When communication conditions are bad, the fax may not be transmitted correctly. In that case,
set a lower TX Start Speed.
1Press [Menu].
2Press [▲] or [▼] to select System Menu.
3Press [OK].
4Press [▲] or [▼] to select FAX.
5Press [OK].
6Press [▲] or [▼] to select Transmission.
7Press [OK].
8Press [▲] or [▼] to select TX Start Speed.
9Press [OK].
10Press [▲] or [▼] to select 9600bps, 14400bps or 33600bps.
11Press [OK].
PBX Setting (Europe only)
When using this machine in environment in which PBX for connection to multiple phones for business use is installed,
perform the following PBX setting.
Registering Destinations in the Address Book
Add a new destination to the Address Book. To edit the Address Book, use KYOCERA Client Tool. For details, refer to
Address Book on page 2-39.
Note Normally this should be used with the default setting.
TX Start Speed
b
9600bps
Note Before connecting this machine to PBX, it is recommended to contact the company that installed the PBX
system to request connection of this machine. Note that correct operation cannot be guaranteed in environment in
which this machine is connected to PBX because the functions of this machine may be restricted.
Item Setting value Description
Exchange Select. PSTN Use when connecting this machine to a public switched telephone network
(default).
PBX Use when connecting this machine to PBX.
Dial No. to PSTN 0-9
00-99
Set a number to access an outside line. For the number, contact the PBX
administrator.
Note For more information about configuring settings, refer to Adjustment and Maintenance on page 7-27.
7-7
FAX Operations
Entering the Destination
Entering the Destination Fax Number with the Numeric Keys
The procedure for entering the destination fax number with the numeric keys is explained below.
1Press [FAX].
2Enter the fax number of the receiving system using the numeric keys.
3Press [OK].
Choosing from the Address Book
Select a destination registered in the Address Book.
1Press [FAX].
Note Up to 64 digits can be entered as the fax number of the receiving system.
Pressing [Address Recall/Pause] adds about three seconds of waiting time during
dialing. For example, when dialing the receiving system on an external line, you can
use this method to insert a pause before resuming dialing after you dial a specific
number.
Note To send to multiple destinations, enter the next fax number and press [OK].
You can send to as many as 100 destinations at once.
The TX Start Speed and ECM setting for the destination can be changed. For
details, Checking and Editing Destinations
on page 7-8.
FAX No. Entry
b
0123456789
Note To edit the Address Book, use KYOCERA Client Tool. For details, refer to Address Book on page 2-39.
7-8
FAX Operations
2Press [Address Book].
3Press [▲] or [▼] to select the destination.
4Press [OK].
5Press [▲] or [▼] to select Add Destination.
6Press [OK].
Checking and Editing Destinations
Check and edit a selected destination.
If the fax number of the destination was entered with the numeric keys, the TX Start Speed and ECM settings can be
changed.
1Press [Menu].
Note A numeric key can be pressed to display the address number search display.
Enter the address number you are searching for with the numeric keys and press
[OK].
Note To check detailed information on the destination, select Detail and press
[OK]. You can check the Address Number, Contact Name, FAX Number, TX Start
Speed, and ECM.
Note To send to multiple destinations, repeat steps 2 to 6. You can send to as many
as 100 destinations at once.
To check or change a selected destination, refer to Checking and Editing
Destinations on page 7-8.
Address Book
b
Support department
Search
b
012
Support department
b
Add Destination
7-9
FAX Operations
2Press [▲] or [▼] to select Dest. Confirm..
3Press [OK].
When the fax number of the destination was entered with the numeric keys
The fax number, TX Start Speed, and ECM can be changed.
1Press [▲] or [▼] to select the destination that you want to check or change, and press
[OK].
2Press [▲] or [▼] to select Detail/Edit.
3Press [OK].
To change the fax number
1Press [▲] or [▼] to select FAX Number.
2Press [OK].
3To change the fax number, reenter the number with the numeric keys.
4Press [OK].
To change the TX Start Speed
1Press [▲] or [▼] to select TX Start Speed.
2Press [OK].
3Press [▲] or [▼] to select the desired TX Start Speed.
4Press [OK].
To change the ECM setting
1Press [▲] or [▼] to select ECM.
2Press [OK].
Menu
b
Dest. Confirm.
Dest. Confirm.
b
0123456789
0123456789
b
Detail/Edit
Edit
b
FAX Number
FAX Number
b
0123456789
Edit
b
TX Start Speed
TX Start Speed
b
33600bps
Edit
b
ECM
7-10
FAX Operations
3Press [▲] or [▼] to select On or Off.
4Press [OK].
When the destination was selected from the Address Book
The information stored in the destination can be checked.
1Press [▲] or [▼] to select the destination that you want to check, and press [OK].
2Press [▲] or [▼] to select Detail.
3Press [OK].
4Press [▲] or [▼] to select the item that you want to check.
5Press [OK].
To delete a destination 1Press [▲] or [▼] to select the destination that you want to delete, and press [OK].
2Press [▲] or [▼] to select Delete.
3Press [OK].
4Press [▲] or [▼] to select Yes.
5Press [OK]. The selected destination is deleted.
ECM
b
On
Note The following items can be checked.
•Contact Name
•FAX Number
•TX Start Speed
•ECM
Dest. Confirm.
b
Support department
Support department
b
Detail
Detail
b
Contact Name
Dest. Confirm.
b
0123456789
0123456789
b
Delete
7-11
FAX Operations
Using Redial
Redial is a function allowing you to dial the last entered number once again.
Use this when the receiving system does not respond when you have tried to send a fax. When you want to send the fax to
the same receiving system, press [Address Recall/Pause], and you can call the receiving system you dialed on the
destination list.
1Press [FAX].
2Press [Address Recall/Pause].
The previously dialed destination is called.
Note Recall information is canceled in the following conditions.
•When you turn the power off
•When you send a next fax (new recall information is registered)
7-12
FAX Operations
Sending Faxes
Fax transmission is explained below.
Basic transmission procedure
The basic procedure for using the fax system is explained below.
1Press [FAX].
2Place the originals. For details, refer to Loading Originals on page 2-18.
3If a program is set, press the program key ([Program 1] - [Program 3]) in which the
program is registered.
4Enter the fax number of the receiving system using the numeric keys.
Note For details on programs, refer to Using Programs on page 7-15.
Note Up to 64 digits can be entered as the fax number of the receiving system.
Pressing [Address Recall/Pause] adds about three seconds of waiting time during
dialing. For example, when dialing the receiving system on an external line, you can
use this method to insert a pause before resuming dialing after you dial a specific
number.
For the procedure for selecting a destination in the address book, refer to Choosing
from the Address Book on page 7-7.
FAX No. Entry
b
0123456789
7-13
FAX Operations
5Adjust density using 7 levels (Lighter -3 to Darker +3).
Press [Density], and press [▲] or [▼] to select your desired density. Press [OK].
6Selecting the functions.
Press [Menu]. FAX transmission settings can be selected.
7Press [Start]. When scanning finishes, transmission starts.
Cancelling the Transmission (while originals are being scanned)
To cancel transmission while originals are being scanned, press [Stop/Reset].
Note For the FAX transmission settings, refer to Fax Transmission Functions on
page 7-16.
Note If you scanned the original from the platen, the display will ask if you will scan
another page.
To scan another page, replace the previous page with the next page, select Yes,
and press [OK]. The next page is scanned.
To send the fax, select No and press [OK]. Transmission starts.
Density
b
Normal 0
Menu
b
FAX Resolution
Scan next orig.
b
No
7-14
FAX Operations
Checki ng an d Deleting a Fax Job
Follow the steps below to check and delete a fax job.
To check a fax job 1Press [Menu].
2Press [▲] or [▼] to select FAX TX Job Status.
3Press [OK].
4Press [▲] or [▼]. The fax number of the destination appears.
If there are multiple destinations, Broadcast appears.
To check Broadcast destinations
5Select Broadcast and press [OK].
6Press [▲] or [▼] to select Detail.
7Press [OK].
8Press [▲] or [▼]. The fax number of the destination appears.
9Press [OK].
To delete a fax job 1Press [Menu].
Menu
b
FAX TX Job Status
FAX TX Job Status
b
0123456789
FAX TX Job Status
b
Broadcast
FAX TX Job Status
b
Broadcast
Broadcast
b
Detail
Detail
b
0123456789
7-15
FAX Operations
2Press [▲] or [▼] to select FAX TX Job Status.
3Press [OK].
4Press [▲] or [▼] to select the fax job you want to delete.
5Press [OK].
6Press [▲] or [▼] to select Cancel.
7Press [OK].
8Press [▲] or [▼] to select Yes.
9Press [OK]. The selected job is deleted.
Using Programs
Frequently used destinations and transmission settings can be registered in [Program 1] - [Program 3].
To use a program, press the program key ([Program 1] - [Program 3]) in which the program is registered.
The programs below have been preregistered. The registered contents can be re-registered for easier use in your
environment.
Menu
b
FAX TX Job Status
FAX TX Job Status
b
0123456789
0123456789
b
Cancel
Item Program1 Program2 Program3
Original size A4 (Letter) A4 (Letter) A4 (Letter)
Original image Text Text+Photo Photo
Density Normal (0) Normal (0) Normal (0)
Resolution 200 × 100 dpi 200 × 100 dpi 200 × 100 dpi
Destination (Not Registered) (Not Registered) (Not Registered)
Note Programs are registered from your computer using Preset Tool. For details, refer to Default and Program
Settings on page 2-32.
7-16
FAX Operations
Fax Transmission Functions
Selecting the Fax Resolution
Select fineness of images when sending fax. The larger the number, the better the image resolution. However, better
resolution also means larger file sizes and longer send times.
1Press [FAX].
2Press [Menu].
3Press [▲] or [▼] to select FAX Resolution.
4Press [OK].
5Press [▲] or [▼] to select the fax resolution.
6Press [OK].
Original Size
Specify the size of originals being scanned.
Original sizes that can be selected are shown below.
Item Description
200×100dpi Norm. when sending originals with standard size
characters Typical character size: 10.5 point
(example: Resolution Resolution)
200×200dpi Fine when sending originals with relatively small
characters and thin lines Typical character size: 8 point
(example: Resolution Resolution)
200×400dpi S.Fin when sending originals with minute
characters and lines Typical character size: 6 point
(example: Resolution Resolution)
Note The default setting is 200×100dpi Norm. The higher the resolution, the clearer the image, but the fax
transmission time is longer.
FAX Resolution
b
200×400dpi S.Fin
Model Original Size
Metric Models A4, A5, A6, B5, Folio, Letter, Legal, S tatement, Executive, Oficio II, 216 × 340 mm, 16K, Others (ISO
B5, Custom)
Inch Models Letter, Legal, S tatement, Executive, Oficio II, 216 × 340 mm, A4, A5, A6, B5, Folio, 16K, Others (ISO
B5, Custom)
7-17
FAX Operations
1Press [FAX].
2Press [Menu].
3Press [▲] or [▼] to select Original Size.
4Press [OK].
5Press [▲] or [▼] to select the desired original size.
To select ISO B5 or Custom, select Others, press [OK], select ISO B5 or Custom, and
press [OK].
6Press [OK].
Original Image
Select image quality suited to the type of original.
1Press [FAX].
Note To use Custom, register the custom size of the original. For details, refer to Configuration on page 2-48.
Original Size
b
A4
Item Description
Text+Photo Best for originals which contain a mixture of text and photos.
Photo Best for photographs.
Text Sharply renders pencil text and fine lines.
7-18
FAX Operations
2Press [Menu].
3Press [▲] or [▼] to select Original Image.
4Press [OK].
5Press [▲] or [▼] to select the image quality suited to the type of original.
6Press [OK].
Manual Send
This method allows you to send originals by pressing [Start] after confirming that the telephone line has connected to the
receiving system.
1Press [FAX].
2Place the originals. For details, refer to Loading Originals on page 2-18.
3Press [On Hook].
4Press [▲] or [▼] to select Manual TX.
5Press [OK].
Original Image
b
Text+Photo
On Hook
b
Manual TX
7-19
FAX Operations
6Use the numeric keys to enter the number of the receiving system. The destination number
is dialed.
7When you hear the fax tone, the telephone line has connected to the receiving system.
Press [Start]. Transmission begins.
Using Chain Dial
Chain dial is a function that allows you to dial by linking fax numbers of the receiving systems with a chain number created
with a number common to several destinations.
By setting multiple phone numbers from several telephone companies to a chain number, you can later choose the one
that costs the least to send the fax to a remote or international destination.
1Press [FAX].
2Place the originals. For details, refer to Loading Originals on page 2-18.
3Enter the fax number to be added to the chain number. Select the address in which the
chain number is registered in the Address Book, or enter the chain number with the
numeric keys. For details, refer to Entering the Destination on page 7-7.
4Press [Menu].
On Hook
b
0123456789
Note You can use the chain number at the head of the fax number of the receiving system. It is convenient to register
chain numbers that are used frequently to the Address Book.
7-20
FAX Operations
5Press [▲] or [▼] to select Dest. Confirm..
6Press [OK].
7Press [▲] or [▼] to select the chain number and press [OK].
8Press [▲] or [▼] to select Chain.
9Press [OK].
To select the fax number to be added to the chain number from the Address Book
10Press [▲] or [▼] to select Address Book.
11Press [OK].
12Press [▲] or [▼] to select the destination.
13Press [OK].
14To select the next fax number, repeat steps from step 3.
To enter the fax number to be added to the chain number with the numeric keys
15Press [▲] or [▼] to select Address Entry.
16Press [OK].
17A chain number is already entered, so enter the fax number with the numeric keys.
18Press [OK].
19To select the next fax number, repeat steps from step 3.
20Press [Start]. Transmission begins.
Menu
b
Dest. Confirm.
Dest. Confirm.
b
212
212
b
Chain
Chain
b
Address Book
Address Book
b
Support department
Chain
b
Address Entry
Address Entry
b
212
7-21
FAX Operations
Receiving Faxes
FAX Automatic Reception
To have the machine receive faxes automatically, no special operation is required.
Flow of Reception
1Reception Starts.
When a fax has been sent to you, the machine starts receiving the fax.
After reception has started, the Processing indicator blinks.
2Reception Print.
Received faxes are output to the inner tray with the printed side facing down. The inner tray can
hold a maximum of 100 sheets of plain paper (80 g/m²). However, the number of sheets varies
with the condition of the paper to be used.
IMPORTANT When the number of sheets to be printed exceeds the number of sheets that
can be held, remove all the paper on the inner tray.
Even if the machine is not capable of printing due to paper running out or a paper jam, it
can still receive faxes (memory reception).
Memory Reception
When the machine cannot print a fax due to paper running out or a paper jams, it temporarily stores originals that have
been sent in the image memory. When the machine returns to the printable state, printing starts.
To print the received originals, supply paper or remove jammed paper.
Note You can change the number of times the ringing tone rings. (Refer to Fax Settings
on page 7-24.)
7-22
FAX Operations
Fax Reception Settings
Reception Date/Time
Reception Date/Time function adds the reception date/time, sender information and number of pages on the top of each
page when the message is printed out. It is useful for confirming the time of reception if the fax is from a different time
zone.
For more information about configuring settings, refer to Fax Settings on page 7-24.
Duplex Print Output (FS-1125MFP and FS-1325MFP only)
Performs duplex printing if a fax of multiple pages are received when printing a fax.
For more information about configuring settings, refer to Fax Settings on page 7-24.
Note When the received fax data is forwarded after retrieving it from memory, the reception date/time is not added
to the forwarded data.
Item Description
On Print the reception date/time.
Off Do not print the reception date/time.
Item Description
On Print on both sides.
Off Do not print on both sides.
7-23
FAX Operations
Printing Communication Reports
You can set fax communication reports to check transmission/reception status.
Note To set reports, refer to Report on page 7-25.
When a fax communication error occurs, an error code will be indicated on the report. For information on error
codes, refer to FAX Error Code List on page 9-12.
Reports Description
Admin Rpt Set. Outgoing FAX
Rpt This administration report is printed after every 50 fax transmissions.
Incoming FAX
Rpt This administration report is printed after every 50 fax receptions.
Result Rpt
Set. FAX RX Result Each time you receive a fax, you can print a report to confirm whether the fax
was received successfully. You can also have the report printed only when an
error occurs.
FAX TX Result Each time you send a fax, you can print a report to confirm whether th e fax was
sent successfully. You can also print the transmitted image in the send result
report.* You can also have the report printed only when an error occurs.
* Only when sending in the memory transmission mode.
FAX TX Report
FS-
FAX RX Report
FS-
FAX RX Result Report
Complete
FS-
FAX Send Result Report
FS-
Complete
7-24
FAX Operations
Fax Settings
Default Fax Settings
This section explains the fax settings in the System Menu.
Operation Method
1Press [Menu].
2Press [▲] or [▼] to select System Menu.
3Press [OK].
4Press [▲] or [▼] to display the desired menu.
5Press [OK].
6Use [▲] or [▼] or the numeric keys to change the setting.
7Press [OK]. The setting is registered. To exit, press [Menu].
Note If the Administrator ID entry display appears, use the numeric keys to enter the
Administrator ID (4 digits) and press [OK]. The default setting is 2500 for the
FS-1025MFP, FS-1125MFP and FS-1325MFP, 2000 for the FS-1120MFP and
FS-1320MFP.
For details of Administrator ID, refer to Administrator ID on page 6-6.
Menu
b
System Menu
System Menu
b
Report
System Menu
b
Common Settings
The setting items successively
appear as [▲] or [▼] is pressed.
Common Settings
b
Language
When [OK] is pressed, the next setting
of the selected item appears. To return
to the previous display, press [Back].
Administrator ID
b
(0000 - 9999)
****
Language
b
*English
7-25
FAX Operations
System Menu Settings
Settings for the fax function in the system menu are shown below.
Report
Print reports to check the machine settings and status. Default settings for printing the result reports can also be
configured.
Common Settings
Configures overall machine operation.
• Sound
Note For settings other than fax settings, refer to Default Setting (System Menu) on page 6-1.
The System Menu contains some menus that can be set from a computer. Refer to Configuration on page 2-48.
Item Description Reference
Page
Report Print reports to check the machine settings and status. Default settings for
printing the result reports can also be configured. 7-25
Common Settings Configures overall machine operation. 7-25
FAX Settings Configures settings for fax functions. 7-26
Administrator Change the Administrator ID. For details, refer to Administrator ID on page 6-6.6-6
Adjust/Maint. Adjust printing quality and conduct machine maintenance. 7-27
Item Description
Status Page A status page provides information on a number of user setups. FAX-related
information includes the Local FAX Number, Local FAX Name, fax line setting,
etc. You can print it out as necessary.
Admin Rpt
Set. Outgoing FAX Rpt The administration report is printed after every 50 fax transmissions.
Value: Off, On
Incoming FAX Rpt The administration report is printed after every 50 fax receptions.
Value: Off, On
Result Rpt
Set. FAX RX Result Each time you receive a fax, you can print a report to confirm whether the fax
was received successfully.
Value: Off, On, Error Only
FAX TX Result Each time you send a fax, you can print a report to confirm whether the fax was
sent successfully. You can also print the transmitted image in the send result
report.
Value: Off, On, Error Only
Attach Image When On or Error Only is selected, the transmitted image is added to the
report.
Value: Off, On
Item Description
FAX Speaker Adjust the volume of the speaker.
Speaker Volume: Volume of the built-in speaker when the line is connected by pressing
[On Hook].
Value: 0 Mute, 1 Minimum, 2, 3 Medium, 4, 5 Maximum
FAX Monitor Adjust the volume of the monitor.
Monitor Volume: Volume of the built-in speaker when the line is connected without
pressing [On Hook] such as in memory transmission.
Value: 0 Mute, 1 Minimum, 2, 3 Medium, 4, 5 Maximum
7-26
FAX Operations
•Original Size
Specify the original size to be scanned. For details, Original Size on page 6-4.
• Paper Settings
Set the paper size to load in the cassette. For details, Paper Settings on page 6-4.
• Date Settings
Configure Date/Time and Date Format settings. For details, Setting Date and Time on page 7-2.
• Timer Settings
FAX Settings
Settings related to the fax function can be configured.
•Transmission
Note If the Administrator ID entry display appears, use the numeric keys to enter the Administrator ID (4 digits).
The default setting is 2500 for the FS-1025MFP, FS-1125MFP and FS-1325MFP, 2000 for the FS-1120MFP
and FS-1320MFP.
For details of Administrator ID, refer to Administrator ID on page 6-6.
Item Description
Unusable Time Set the unusable time. For detail, refer to Unusable Time on page 7-35.
Item Description
TTI The transmit terminal identification (TTI) is the information about the machine (transmit
terminal) to be printed out on the fax on the receiving system.
The information includes transmission date and time, the number of transmission pages,
and the fax number. Refer to TTI (Transmit Terminal Identification) on page 7-3.
Local FAX Name Register the local FAX name printed on in the transmit terminal identification. Refer to
Local FAX Name on page 7-3.
Local FAX Number Register the local FAX number printed on in the transmit terminal identification (TTI) area.
Refer to Local FAX Number on page 7-4.
FAX Dialing Mode Select the telephone line according to the type you are contracted with. Please note that
selecting a wrong telephone line will prevent you from sending fax. Refer to FAX Dialing
Mode on page 7-4.
Note This setting does not appear in some regions.
Retry Times The number of automatic retry times can be changed.
ECM TX Set whether ECM TX is performed. ECM is a communication mode specified by the ITU-T
(International Telecommunication Union) that retransmits data whe n an error occurs. Fax
machines that have ECM mode check for errors as they communicate, preventing
distortion of the image due to noise on the line and other conditions. Refer to ECM TX on
page 7-5.
Value: On, Off
Note When there is a large amount of noise on the line, communication may take slightly
longer than when Off is selected.
TX Start Speed Set the TX Start Speed. When communication conditions are bad, the fax may not be
transmitted correctly. In that case, set a lower TX Start Speed. Ref er to TX S t art Speed on
page 7-6.
Value: 9600bps, 14400bps, 33600bps
Note Normally this should be used with the default setting.
7-27
FAX Operations
• Reception
Adjustment and Maintenance
Adjust printing quality and conduct machine maintenance.
• Service Settings
Item Description
Rings(Normal) The number of rings until the machine answers a call can be changed as needed.
Note This setting does not appear in some regions.
RX Settings Select the reception mode.
Value: Auto(Normal), Auto(DRD)
Note DRD reception mode is only available for Australia and New Zealand. This setting
does not appear in other regions.
Forward Settings Configure Forward Settings. Refer to Forward Settings on page 7-28.
RX Date/Time Reception Date/Time function adds the reception date/time, sender information and
number of pages on the top of each page when the message is printed out. It is useful for
confirming the time of reception if the fax is from a different time zone.
Value: On, Off
Duplex Printing Performs duplex printing if a fax of multiple pages are received when printing a fax.
Value: On, Off
RX Restriction Set Reception Restriction. Refer to RX Restriction on page 7-34.
Unknown Number RX When Reception Restriction is set, you can set whether or not reception is allowed from
parties that do not provide notification of their fax number. Refer to RX Restriction on
page 7-34.
ECM RX Set whether ECM RX is performed.
Value: On, Off
RX Start Speed Set the RX Start Speed.
Value: 9600bps, 14400bps, 33600bps
Note If the Administrator ID entry display appears, use the numeric keys to enter the Administrator ID (4 digits).
The default setting is 2500 for the FS-1025MFP, FS-1125MFP and FS-1325MFP, 2000 for the FS-1120MFP
and FS-1320MFP.
For details of Administrator ID, refer to Administrator ID on page 6-6.
Item Description
FAX Country Code To use this menu, consult your dealer or service representative.
FAX Call Set.*
* This setting does not appear in some regions.
When using this machine in environment in which PBX for connection to multiple phones
for business use is installed, perform the following PBX setting.
Exchange Select. If the machine is connected to a PBX, set PBX.
Value: PBX, PSTN
Dial No. to PSTN Set a number to access an outside line. For the number, contact the PBX administrator.
Value: 0-9, 00-99
7-28
FAX Operations
Forward Settings
When you have received a fax, you can forward the received image to other fax machines, or set printing.
Setting Forwarding
Use the procedure below to set forwarding.
1Press [Menu].
2Press [▲] or [▼] to select System Menu.
3Press [OK].
4Press [▲] or [▼] to select FAX.
5Press [OK].
6Press [▲] or [▼] to select Reception.
7Press [OK].
8Press [▲] or [▼] to select Forward Settings.
9Press [OK].
10Press [▲] or [▼] to select Forwarding.
11Press [OK].
12To set Forwarding, press [▲] or [▼] to select On.
13Press [OK].
Registering Forwarding Destination
Use the procedure below to register a forwarding destination.
1Press [Menu].
2Press [▲] or [▼] to select System Menu.
3Press [OK].
4Press [▲] or [▼] to select FAX.
5Press [OK].
6Press [▲] or [▼] to select Reception.
7Press [OK].
Forward Settings
b
Forwarding
Forwarding
b
On
7-29
FAX Operations
8Press [▲] or [▼] to select Forward Settings.
9Press [OK].
10Press [▲] or [▼] to select Forward Dest..
11Press [OK].
12Press [▲] or [▼] to select Add.
13Press [OK].
Selecting Forwarding Destination from Address Book
14Press [▲] or [▼] to select Address Book.
15Press [OK].
16Press [▲] or [▼] to select the destination.
17Press [OK].
Entering Forwarding Destination Directly
18Press [▲] or [▼] to select Address Entry.
19Press [OK].
20To change the fax number, reenter the number with the numeric keys.
21Press [OK].
Changing and Deleting Registration Contents
Use the procedure below to change or delete registration contents.
1Press [Menu].
2Press [▲] or [▼] to select System Menu.
3Press [OK].
Forward Settings
b
Forward Dest.
Forward Dest.
b
Add
Add
b
Address Book
Address Book
b
Support department
Add
b
Address Entry
Address Entry
b
0123456789
7-30
FAX Operations
4Press [▲] or [▼] to select FAX.
5Press [OK].
6Press [▲] or [▼] to select Reception.
7Press [OK].
8Press [▲] or [▼] to select Forward Settings.
9Press [OK].
10Press [▲] or [▼] to select Forward Dest..
11Press [OK].
12Press [▲] or [▼] to select Confirmation.
13Press [OK].
When the fax number of the destination was entered with the numeric keys
The fax number, TX Start Speed, and ECM can be changed.
1Press [▲] or [▼] to select the destination to be changed, and press [OK].
2Press [▲] or [▼] to select Detail/Edit.
3Press [OK].
4Press [▲] or [▼] to select FAX Number.
5Press [OK].
6To change the fax number, reenter the number with the numeric keys.
7Press [OK].
8Press [▲] or [▼] to select TX Start Speed.
9Press [OK].
10Press [▲] or [▼] to select the desired TX Start Speed.
Forward Settings
b
Forward Dest.
Forward Dest.
b
Confirmation
Confirmation
b
0123456789
0123456789
b
Detail/Edit
Edit
b
FAX Number
FAX Number
b
0123456789
Edit
b
TX Start Speed
TX Start Speed
b
33600bps
7-31
FAX Operations
11Press [OK].
12Press [▲] or [▼] to select ECM.
13Press [OK].
14Press [▲] or [▼] to select On or Off.
15Press [OK].
When the destination was selected from the Address Book
The information stored in the destination can be checked.
1Press [▲] or [▼] to select the destination that you want to check, and press [OK].
2Press [▲] or [▼] to select Detail.
3Press [OK].
4Press [▲] or [▼] to select the item that you want to check.
5Press [OK].
To delete the forwarding destination
1Press [▲] or [▼] to select the destination that you want to delete, and press [OK].
2Press [▲] or [▼] to select Delete.
3Press [OK].
4Press [▲] or [▼] to select Yes.
5Press [OK]. The selected destination is deleted.
Edit
b
ECM
ECM
b
On
Note The following items can be checked.
•Contact Name
•FAX Number
•TX Start Speed
•ECM
Confirmation
b
Support department
Support department
b
Detail
Detail
b
Contact Name
Confirmation
b
0123456789
0123456789
b
Delete
7-32
FAX Operations
Forwarding Time Setting
Register the start time and end time between which forwarding is enabled.
1Press [Menu].
2Press [▲] or [▼] to select System Menu.
3Press [OK].
4Press [▲] or [▼] to select FAX.
5Press [OK].
6Press [▲] or [▼] to select Reception.
7Press [OK].
8Press [▲] or [▼] to select Forward Settings.
9Press [OK].
10Press [▲] or [▼] to select Forward Time.
11Press [OK].
12Press [▲] or [▼] to select All day or Preset Time.
To forward all day, select All day and press [OK].
To set a forwarding start time and end time, select Preset Time and press [OK], and then
set the start time and end time.
Forwarding start time and end time settings
13Enter the Start Time with the numeric keys.
Enter the ‘hour’ and press [OK]. The ‘minute’ can now be entered.
14Press [OK].
15Enter the End Time with the numeric keys.
Enter the ‘hour’ and press [OK]. The ‘minute’ can now be entered.
16Press [OK].
Forward Settings
b
Forward Time
Forward Time
b
All day
Start Time
b
:00
08
End Time
b
:00
17
7-33
FAX Operations
Print Setting
You can set whether the machine should print received originals when forwarding them.
1Press [Menu].
2Press [▲] or [▼] to select System Menu.
3Press [OK].
4Press [▲] or [▼] to select FAX.
5Press [OK].
6Press [▲] or [▼] to select Reception.
7Press [OK].
8Press [▲] or [▼] to select Forward Settings.
9Press [OK].
10Press [▲] or [▼] to select Print.
11Press [OK].
12Press [▲] or [▼] to select On (print) or Off (do not print).
13Press [OK].
Forward Settings
b
Print
Print
b
On
7-34
FAX Operations
RX Restriction
Reception from parties re gistered in the Reject List a nd p arties that have not registered the ir TTI (own fax number) can be
rejected. (You can select whether reception from parties that have not registered their TTI is allowed or not allowed in
Unknown Number RX on page 7-34.)
Setting RX Restriction
To reject reception from parties registered in the Reject List, follow the steps below.
1Press [Menu].
2Press [▲] or [▼] to select System Menu.
3Press [OK].
4Press [▲] or [▼] to select FAX.
5Press [OK].
6Press [▲] or [▼] to select Reception.
7Press [OK].
8Press [▲] or [▼] to select RX Restriction.
9Press [OK].
10Press [▲] or [▼] to select Reject List.
11Press [OK].
Unknown Number RX
When RX Restriction is set, you can select whether reception from p arties that do not provide notification of their TTI (own
fax number) is allowed or not allowed. To change the RX Restriction setting for parties that do not provide notification of
their TTI, follow the steps below.
1Press [Menu].
2Press [▲] or [▼] to select System Menu.
Note The Reject List is registered from your computer. For details, refer to Address Book on page 2-39.
Note To set RX Restriction, turn on Enable number blocking. For details, refer to Registering Reject List on
page 2-43.
RX Restriction
b
Reject List
Note To set Unknown Number RX, turn on Block all unknown numbers. For details, refer to Registering Reject
List on page 2-43.
7-35
FAX Operations
3Press [OK].
4Press [▲] or [▼] to select FAX.
5Press [OK].
6Press [▲] or [▼] to select Reception.
7Press [OK].
8Press [▲] or [▼] to select Unknown Number RX.
9Press [OK].
10Press [▲] or [▼] to select Reject or Permit.
11Press [OK].
Unusable Time
This feature sets a time period during which the machine will not print received faxes. Even during Unusable Time, it is
possible to perform an operation by entering the unlock code (4 digits).
Follow the steps below to set Unusable Time and register the unlock code for Unusable Time.
1Press [Menu].
2Press [▲] or [▼] to select System Menu.
3Press [OK].
4Press [▲] or [▼] to select Common Settings.
5Press [OK].
6Press [▲] or [▼] to select Timer Settings.
7Press [OK].
8Use the numeric keys to enter the Administrator ID. The default setting is 2500 for the
FS-1025MFP, FS-1125MFP and FS-1325MFP, 2000 for the FS-1120MFP and
FS-1320MFP.
9Press [OK].
10Press [▲] or [▼] to select Unusable Time.
11Press [OK].
12Press [▲] or [▼] to select On.
13Press [OK].
Unknown Number RX
b
Reject
IMPORTANT When Unusable Time is set, in addition to FAX printing, all other operations are all prohibited during
the unusable time period, including printing of copy jobs and printer jobs, and FAX Driver transmission.
Administrator ID
b
(0000 - 9999)
****
Unusable Time
b
On
7-36
FAX Operations
14Enter the Start Time with the numeric keys.
Enter the ‘hour’ and press [OK]. The ‘minute’ can now be entered.
15Press [OK].
16Enter the End Time with the numeric keys.
Enter the ‘hour’ and press [OK]. The ‘minute’ can now be entered.
17Press [OK].
18Enter the unlock code.
19Press [OK].
Using the Machine During Unusable Time
To temporarily use the machine during Unusable Time, enter the unlock code and press [OK].
IMPORTANT When the Start Time and End Time are set to the same time, th e setting
is treated as ‘all day’.
Start Time
b
:00
08
End Time
b
:00
17
Unlock Code
b
(0000 - 9999)
0000
Unlock Code
b
(0000 - 9999)
0000
7-37
FAX Operations
Sending Faxes from PC
The FAX Driver function makes it possible to send faxes from any computer connected by USB or network cable. Its
primary features include the following.
•PC-prepared document can be sent by fax without being printed out.
•An Address Book (in the machine/PC) can be used to specify a desired destination.
•Addition of a cover page.
Flow of Sending Faxes from PC
Sending faxes from PC is performed in the following sequence.
Setup
Connection to a PC
Connect the machine to a PC using the network cable or USB cable. For details, refer to Connections on page 2-2.
Installing Software on the PC
Install the dedicated software (included in the supplied Product Library disc) on your PC required to use FAX Driver.
For details, refer to Installing and Uninstalling Drivers and Utilities on page 2-20.
Prepare a document using a PC connected to this machine.
Forward the document data from the PC to this machine using the
same operation as for printing.
The machine sends the document data to another fax machine.
The other fax machine receives the data.
7-38
FAX Operations
Basic Transmission
1Use an application on your computer to create the document to be sent.
2Select Print from the File menu. The Print screen for the applicatio n that you are using will
appear.
3Use the drop-down menu in the Name field to select the name of the machine to be used
as the FAX Driver.
4Enter the page numbers, etc., to be faxed.
5Click Properties to open the Properties screen.
6Specify fax settings such as the original size on the FAX Setting tab, and click OK.
7You will return to the Print screen for the application. Click OK. The Transmit Settings
screen will appear.
Note Make sure that the number of copies is set to 1. The following screen is an
example. The actual dialog box will vary depending on the application that you are
using.
Note For detailed information on the settings on the tab, refer to Configuring the
Driver Default Settings on page 7-40.
7-39
FAX Operations
8Set the destination.
9Specify a cover page.
To include a cover page, select settings on the Cover Page tab.
10Set the sender information.
When the sender information is not set in the default settings, click on the Sender
Information tab and set the sender information.
11Click Send. Transmission will begin.
Note For the procedures for using and registering destinations in the Address Book,
refer to FAX Driver Operation Guide.
Note For details on the settings, refer to FAX Driver Operation Guide.
Note For details on the settings, refer to FAX Driver Operation Guide.
Use the keyboard to enter the
destination fax number.
Click Add to Destination List. The
destination information will appear in
the address list. To send to multiple
destinations, repeat this operation.
To use the Address Book, click Select
from Address Book and select the
destination.
7-40
FAX Operations
Configuring the Driver Default Settings
Use the FAX Setting tab of the print settings screen to set the original size and other transmission conditions.
1From the start button, click Control Panel, Hardware and Sound, and Devices and
Printers.
2Right-click the product name of the machine you are using and select Printing
preferences from the drop-down menu. The Printing Preferences screen will open.
3Select settings.
The following settings can be specified.
No. Item Description
1 Page Size Select the size of the document being transmitted from the
dropdown list.
Value: Letter (8.5 x 11 in.), Legal (8.5 x 14 in.), Statement
(5.5 x 8.5 in.), A4 (8.27 x 11.69 in.), A5 (5.83 x 8.27 in.),
Folio (8.27 x 12.99 in.), B5 (JIS) (7.17 x 10.12 in.)
2Orientation Specify whether the orientation of the document is portrait or
landscape.
Value: Portrait, Landscape
3 Resolution Select the resolution of the document to be transmitted from
the drop-down list.
Value: 200 × 100 dpi Normal, 200 × 200 dpi Fine
4 FAX TX Setting Click FAX TX Setting to change the default settings for fax
transmission. The Default Settings screen will appear.
For detailed information on the settings, refer to FAX Driver
Operation Guide.
5 OK/Cancel/Apply Clicking OK exits the Printing Preferences after applying the
modified settings.
Clicking Cancel exits the Printing Preferences without
applying the modified settings.
Clicking Apply applies the modified settings without exiting
the Printing Preferences.
1
2
3
4
5
8-1
8 Maintenance
This chapter explains the following topics:
General Information............................................................................................................................................... 8-2
Toner Container Replacement .............................................................................................................................. 8-2
Maintenance Kit Replacement ................. ... ... ....................................................................................................... 8-5
Cleaning the Machine ............................................................................................................................................ 8-5
Maintenance Menu................... .... ... ...... .... ... ... ....................................................................................................... 8-8
Prolonged Non-Use and Moving of the Machine ................................................................................................ 8-9
8-2
Maintenance
General Information
This chapter describes basic maintenance tasks you can perform for the machine. You can replace the toner container
according to the machine's status:
Also, the internal parts need periodic cleaning.
Toner Container Replacement
When the machine becomes low on toner, message display displays Toner is running out. Note the replacement is
not always necessary at this stage.
If you ignore the above status and continue printing, message display displays Add toner. just before the toner is used
up and the machine will stop. The toner container must then be replaced immediately.
In either case, replace the toner container.
Frequency of toner container replacement
According to ISO 19752 and EcoPrint switched off the toner container can print as follows (A4/Letter paper is assumed):
2,500 pages (FS-1120MFP), 3,000 pages (FS-1025MFP and FS-1125MFP), 1,600 pages (FS-1320MFP) or 2,100 pages
(FS-1325MFP).
You can print a status page to check how much toner remains in the toner container. The Toner Gauge in the
consumables status section on the status page shows a progress bar, which roughly represents how much toner is left in
the toner container.
Starter Toner Container
The toner container packed with the new machine is a starter toner cont ainer. The starter toner cont aine r last s an average
of 700 pages (FS-1120MFP and FS-1320MFP) or 1,000 pages (FS-1025MFP, FS-1125MFP and FS-1325MFP).
Toner Kits
For best results, we recommend that you only use genuine Kyocera Parts and Supplies. Should any damage be caused by
the application of a toner other than the original toner, then this damage is excluded from the guarantee.
A new toner kit contains the following items:
•Toner Container
•Plastic waste bag for old toner container
•Installation Guide
Note Information Collection on Memory Chips - The memory chip attached to the toner container is designed to
improve convenience for the end user; to support the recycling operation of empty toner containers; and to gather
information to support new product planning and development. The information gathered is anonymous - it cannot
be associated to any specific individual and the data is intended to be used anonymously.
Note If Non-genuine toner is installed appears in KYOCERA Client Tool after the toner container is replaced, the
installed toner container is non-genuine.
The manufacturer assumes no responsibility for damage caused by a non-genuine toner.
We recommend that you only use genuine toner containers.
When you want to use the toner container currently installed, press [Stop/Reset] and [OK] simultaneously for 3
seconds or more.
Note Do not remove the toner container from the carton until you are ready to install it in the machine.
8-3
Maintenance
Replacing the Toner Container
This section explains how to replace the toner container.
1Open the front cover.
2Pull out the toner container.
3Take the new toner container out of the toner kit. Shake the new toner cont ainer at least 10
times as shown in the figure in order to distribute the toner evenly inside the container.
CAUTION Do not attempt to incinerate the Toner Container. Dangerous sparks may cause burns.
IMPORTANT During toner cont ainer replacement, temp orarily move storage media and com puter supplies (such as
floppy disks) away from the toner container. This is to avoid damaging media by th e magnetism of toner.
KYOCERA Document Solutions Inc. is not liable against any damages or problems ar ising from the use of toner
containers other than those designated as original Kyocera toner containers. For optimum performance, it is also
recommended to use only the Kyocera toner containers which are specifically intended for use in your cou ntry or
region. If the toner container for another destinations is installed, the machine will stop printing.
Note You do not have to turn machine power off before starting the replacement. Any data that may be processing
in the machine will be deleted if you turn the machine power off.
Note Put the old toner container in the plastic bag (supplied with the new toner kit)
and discard it later according to the local code or regulations for waste disposal.
8-4
Maintenance
4Install the new toner container in the machine. Push in firmly until you hear a "click" sound.
5Close the front cover. Toner is replenished for about 4 seconds.
Note If the front cover does not close, check that the new toner container is installed
correctly (in step 4).
After use, always dispose of the toner container in accordance with Federal, State
and Local rules and regulations.
8-5
Maintenance
Maintenance Kit Replacement
When the machine prints 100,000 pages, a message is printed indicating that the maintenance kit should be replaced. The
maintenance kit must then be replaced immediately.
To replace the maintenance kit, contact your service representative.
Contents:
•Drum unit
•Developer unit
•Waste toner box
•Feed roller
•Lower paper feed guide
•Transfer roller
Cleaning the Machine
Clean the machine regularly to ensure optimum output quality.
Document Processor/Platen
Wipe the inside of the document processor and the platen with a soft cloth dampened with alcohol or mild detergent.
Note Do not use organic solvents or other strong chemicals.
8-6
Maintenance
Slit Glass Cover
When the slit glass cover is dirty, remove the slit glass cover and wipe the front and back surfaces of the cover and the slit
glass with a soft cloth moistened with alcohol or a diluted neutral detergent.
Interior of the Machine
To avoid print quality problems, the interior of the machine must be cleaned with every toner container replacement.
1Open the rear cover.
Note Do not use organic solvents or other strong chemicals.
Make sure the slit glass has dried completely before replacing it.
8-7
Maintenance
2Use a clean, lint-free cloth to wipe dust and dirt off the metal and rubber rollers, conveying
unit, and paper feed unit.
IMPORTANT Take care not to touch the drum and transfer roller (black) during
cleaning.
Transfer Roller
Rubber Roller
Conveying Unit
Paper Feed Unit
Drum
Metal Roller
8-8
Maintenance
Maintenance Menu
The Maintenance Menu that the user can adjust from KYOCERA Client Tool is described below. In addition, also refer to
KYOCERA Client Tool User Guide.
Maintenance Menu Description
Adjust print
quality Drum charge
setting When print quality has deteriorated, the output of the main charger can be
changed to restore print quality.
Altitude setting If you are using the machine at an altitude of 1500 m or higher and print
quality has deteriorated, the Altitude setting can be used to restore print
quality.
Drum refresh Perform Drum refresh when images show streaking with white lines.
Adjust print
position Printing start
position Single-sided printing
Adjust the position of the printed
image.
Duplex printing
Adjust the position of the image
printed on the back side of the paper
when duplex printing is used.
Print margins Adjust the width of the top edge,
bottom edge, left edge and right edge
margins.
Note This setting is not effective for
the printing from the machine.
B
A: Left edge
B: Top edge Top edge: +10
A
B
D
A: Left edge
B: Top edge
C: Right edge
D: Bottom edge
Top edge: +10
AC
8-9
Maintenance
Prolonged Non-Use and Moving of the Machine
Prolonged Non-use
If you ever leave the machine unused for a long period of time, remove the power cord from the wall outlet.
We recommend you consult with your dealer about the additional actions you should take to avoid possible damage that
may occur when the machine is used next time.
Moving the Machine
When you move the machine:
•Move it gently.
•Keep it as level as possible to avoid spilling toner inside the machine.
•Be sure to consult a service representative before attempting long distance transportation of the machine.
•Keep the machine horizontal.
Adjust scan
position Scanning start
position Adjust the position of the scanned
image.
Scan margins Adjust the width of the top edge,
bottom edge, left edge and right edge
margins.
Restore factory default Restore factory default settings.
WARNING If you are shipping the ma chine, remove an d pack the developer unit a nd drum unit in a plastic
bag and ship them separately from the machine.
Maintenance Menu Description
Platen: -10
B
D
A: Left edge
B: Top edge
C: Right edge
D: Bottom edge
Top edge: +10
AC
8-10
Maintenance
9-1
9 Troubleshooting
This chapter explains the following topics:
Solving Malfunctions............................................................................................................................................. 9-2
Error Messages ...................................................................................................................................................... 9-8
FAX Error Code List............................................................................................................................................. 9-12
Clearing Paper Jams............................................................................................................ ................................ 9-14
9-2
Troubleshooting
Solving Malfunctions
The table below provides general guidelines for problem solving.
If a problem occurs with your machine, look into the checkpoints and perform procedures indicated on the following pages.
If the problem persists, contact your service representative.
Symptom Checkpoints Corrective Actions Reference
Page
The screen does not
respond when the power
switch is turned on.
Check the power cord. Connect both ends of the power cord
securely. 2-3
Pressing [Start] does not
produce copies. Is there a message on the machine
screen, KYOCERA Client Tool, or the
Status Monitor?
Determine the appropriate response to
the message and respond accordingly. 9-8
Is the machine in Sleep mode? Press any key on the operation panel
to recover the machine from Sleep
mode.
—
The indicators are off
and the motor is not
working.
Check the power cord. Connect both ends of the power cord
securely. 2-3
— Press the power switch. —
The machine will not
print from the computer. Check the power cord. Connect both ends of the power cord
securely. 2-3
Is the machine powered on? Turn on the power switch. —
Are the interface cable connected? Connect the correct interface cable
securely. 2-2
Was the machine powered on before
the interface cable was connected? Power on the machine after
connecting the interface cable. 2-2
Is the print job paused? Resume printing. —
Does an error message appear in the
display on the operation panel? Using the information on page 9-8,
check if an error has occurred and
clear the error.
If the indicators show a pattern not
described on page 9-8, turn the power
switch off and then on again. Print the
job again.
9-8
Check if a status page can be printed. If the status page was printed
successfully, there may be a problem
with the connection to the computer.
Check the connection. To print the
status page, refer to Printing the
Status Page on page 2-58.
2-2
The machine prints a
status page but data
from the computer is not
being printed.
Check the interface cable. Connect both ends of the interface
cable securely. Try replacing the
interface cable.
2-2
Check program files and application
software. Try printing another file or using
another print command. If the problem
occurs with a specific file or
application, check the printer settings
for that application.
—
9-3
Troubleshooting
V apor is emitted near the
inner tray. Check if the temperature is low near
the location of the machine, or if the
paper that is being used has been
exposed to humidity.
Depending on the operating
environment of the machine and the
condition of the paper, heat generated
during printing can evaporate water
moisture in the printed paper, emitting
vapor from the machine. In this case,
printing can be continued without any
problem.
To correct this, increase the
temperature in the room, and use
paper that has been stored in a dry
place.
—
Blank sheets are
ejected. Are the originals loaded correctly? When placing originals on the platen,
place them face-down and align them
with the original size indicator plates.
2-18
When placing originals in the
document processor, place them
face-up.
2-18
Full black printout or faint
printing. — Open the rear cover and press the
points shown in the figure. If the
problem is not solved even after
printing several pages, call for service.
—
Paper often jams. Is the paper loaded correctly? Load the paper correctly. 2-12, 2-13,
2-16
Is the paper of the supported type? Is
it in good condition? Remove the paper, turn it over, and
reload it. 2-5
Is the paper curled, folded or wrinkled? Replace the paper with new paper. 2-5
Are there any loose scraps or jammed
paper in the machine? Remove any jammed paper. 9-14
2 or more sheets are
overlaps when ejected.
(multi feed)
— Load the paper correctly. 2-12
Symptom Checkpoints Corrective Actions Reference
Page
9-4
Troubleshooting
Printouts are wrinkled. Is the paper damp? Replace the paper with new paper. 2-5
Printouts are curled. Is the paper damp? Replace the paper with new paper. 2-5
Text is missing on the
Windows test page. — This is a problem specific to the
Windows OS. It is not a machine
problem. It does not affect print quality.
—
Printouts have dropouts
or stray dots. Check the Drum charge setting in the
Maintenance Menu. Increase the adjustment value for the
Drum charge setting in the
Maintenance Menu.
8-8
— Run Drum refresh in the Maintenance
Menu. 8-8
— The drum or developer unit may be
damaged. If the problem is not solved
even after printing several pages, call
for service.
—
Printouts have vertical
streaks Is the slit glass cover dirty? Clean the slit glass cover. 8-6
— The drum unit may be damaged. If the
problem is not solved even after
printing several pages, call for service.
—
Faint or blurred printing. Check the toner container. If necessary, replace the toner
container. 8-2
Check the Print density setting in
KYOCERA Client Tool. Increase the adjustment value for the
Print density setting in KYOCERA
Client Tool.
2-50
Check the Drum charge setting in the
Maintenance Menu. Decrease the adjustment value for the
Drum charge setting in the
Maintenance Menu.
8-8
Symptom Checkpoints Corrective Actions Reference
Page
9-5
Troubleshooting
The altitude is 1500 m or
higher and printouts are
too light.
Check the Altitude Setting in the
Maintenance Menu. Set the Altitude Setting in the
Maintenance Menu to 1. If there is still
no improvement, change the value to
2.
8-8
Gray background. Check the toner container. If necessary, replace the toner
container. 8-2
Check the Drum charge setting in the
Maintenance Menu. Increase the adjustment value for the
Drum charge setting in the
Maintenance Menu.
8-8
— Run Drum refresh in the Maintenance
Menu. 8-8
Check the Print density setting in
KYOCERA Client Tool. Decrease the adjustment value for the
Print density setting in KYOCERA
Client Tool.
2-50
Dirt on the top edge or
back of the paper. Check the Drum charge setting in the
Maintenance Menu. Increase the adjustment value for the
Drum charge setting in the
Maintenance Menu.
8-8
Is the interior of the machine dirty? If the problem is not solved even after
printing several pages, clean the
rollers, conveying unit and paper feed
unit.
If the problem is not solved after
cleaning, call for service.
8-6
The previous image
remains and lightly
printed on the
prepunched paper.
Check the Drum charge setting in the
Maintenance Menu. Increase the adjustment value for the
Drum charge setting in the
Maintenance Menu.
Increase the adjustment value 1 level
at a time from the current value.
If there is no improvement after the
value is increased by 1 level, increase
by 1 level again.
If there is still no improvement, return
the setting to the original value.
8-8
Gray background with
horizontal streaks near
the top edge.
Check the Drum charge setting in the
Maintenance Menu. Increase the adjustment value for the
Drum charge setting in the
Maintenance Menu.
8-8
Symptom Checkpoints Corrective Actions Reference
Page
9-6
Troubleshooting
Copies have a moire
pattern (dots grouped
together in patterns and
not aligned uniformly).
Is the original a printed photograph? Set the image quality to Photo.2-34
Texts are not clearly
printed. Did you choose appropriate image
quality for the original? Select appropriate image quality. 2-34
Images are skewed. Are the originals placed correctly? When placing originals on the platen,
align them with the original size
indicator plates.
2-18
Is the paper loaded correctly? Check the position of the paper width
guides. 2-13
Are the application software settings at
the PC set properly? Check that the printing settings are
correct in the application software and
the printer driver.
—
Cannot scan. Check the interface cable. Connect both ends of the interface
cable securely. Try replacing the
interface cable.
2-2
Is the save location correctly
specified? Check the path to the folder where the
scanned image will be saved. 2-45
Cannot send fax. Is the modular cord connected
correctly? Connect the modular cord correctly. 2-3
Has a communication error occurred? Check error codes in the FAX TX/RX
Result or Outgoing/Incoming FAX
Report. If the error code starts with "U"
or "E", perform the corresponding
procedure.
9-12
Is the destination FAX line busy? Send again. —
Does the destination FAX machine
respond? Send again. —
Is there an error other than above? Contact your service representative. —
Cannot perform
broadcast transmission. Is free space available in the memory? Receive after the memory has free
space, or create free space in the
memory.
—
No print output after
reception. Is memory forwarding activated? Check the forwarding destination. 7-28
Symptom Checkpoints Corrective Actions Reference
Page
9-7
Troubleshooting
Tips
Machine problems may be solved easily by following the tips below. When you have encountered a problem that cannot be
solved following the guidelines above, try the following:
•Restart the computer you are using to send print jobs to the machine.
•Obtain and use the latest version of the printer driver. The latest versions of printer drivers and utilities are available at:
http://www.kyoceradocumentsolutions.com.
•Make sure that the procedures for printing are correctly followed in the application software. Consult the
documentation supplied with the application software.
Cannot receive faxes. Is the modular cord connected
correctly? Connect the modular cord correctly. 2-3
Has a communication error occurred? Check error codes in the FAX TX/RX
Result or Outgoing/Incoming FAX
Report. If the error code starts with
"U", perform the corresponding
procedure.
9-12
Is RX (reception) restriction activated? Cancel the RX restriction. 7-34
Is the reception mode correct? Check the reception mode. 7-27
Cannot perform memory
reception. Is free space available in the memory? Receive after the memory has free
space, or create free space in the
memory.
—
Cannot perform memory
forwarding. Is memory forwarding set to On? Check the memory forwarding setting. 7-28
Symptom Checkpoints Corrective Actions Reference
Page
9-8
Troubleshooting
Error Messages
If a problem has occurred in the machine, you will be notified by the following display.
•The Attention indicator on the operation panel is lit or flashing.
•An error message appears in the message display of the machine's operation panel.
•KYOCERA Client Tool and Status Monitor will show the status of the machine.
If the Attention indicator is lit or flashing and an error message appears in the message display of the machine's operation
panel, check the KYOCERA Client Tool or Status Monitor.
Problems that can be resolved by the user are described below.
Note If the indicators light or flash repeatedly in manners not described above, a service error has probably
occurred. Switch off the power switch, unplug the power cord, and then plug the power cord back in and switch on
the power switch. This may clear the error. Even if the error is not cleared, contact your service representative.
When a FAX communication error occurs, an RX/TX Result Report is printed along with the error message that is
displayed. Check the error code that is indicated on the RX/TX Result Report, and refer to FAX Error Code List on
page 9-12 for information on the error. For printing of RX/TX Result Reports, refer to Report on page 7-25.
Message Display Message displayed in
KYOCERA Client Tool and
Status Monitor* Meaning Remedy
Add toner. Add toner The toner has run out. Replace with a new toner
container.
Call service. Error has occurred An error has occurred in the
machine. Make a note of the error code
displayed on the message
display, and contact your
service representative.
Cannot combine
pages. — The machine cannot run this
program due to unusable
original size is registered in
the program.
Change the program settings.
Cannot feed paper. Add paper A paper jam has occurred in
the cassette. Refer to Clearing Paper Jams
on page 9-14 and remove the
jammed paper.
There is no paper in the
paper source. Load paper into the paper
source.
The paper size and media
type settings selected at the
time of faxing are different
from KYOCERA Client Tool
settings.
Check the paper size and
media type settings.
Add toner.
9-9
Troubleshooting
Close the cover. Cover open The rear cover or front cover
is open. Close the rear cover or front
cover.
Close the cover.
Press OK key. Paper jam The document processor
cover is open. Close the document processor
cover and then press [OK].
Error. Power off. Error has occurred Internal error has occurred. Turn the power OFF and then
ON.
FAX memory is
full. Memory full Fax transmission is not
possible due to insufficient
memory.
Press [OK] and the job will be
canceled.
Fax reception is not possible
due to insufficient memory. Press [OK] to clear the error.
Only the received pages are
printed and then the machine
tries to receive the remaining
pages.
Incorrect unlock
code. — The entered Administrator
ID is not correct. Enter the correct Administrator
ID. Refer to Administrator ID on
page 6-6.
Load paper. Add paper The paper size in the paper
source is different from the
printer driver or KYOCERA
Client Tool setting.
Load the proper size of paper in
the paper source.
Maximum Number of
scanned pages. Error has occurred The number of scanned
pages exceeds the
maximum number.
The maximum number of
scanned original pages is 99.
Only the scanned pages are
available. Press [OK] and the
job will be canceled.
Memory is full. Memory overflow Unable to continue the job
as the memory is used up. Change the print resolution
from Fast 1200 to 600 dpi.
Refer to Printer Driver User
Guide.
Non-genuine Toner. Non-genuine toner is
installed The installed toner container
is non-genuine. The manufacturer assumes no
responsibility for damage
caused by a non-genuine toner.
We recommend that you only
use genuine toner containers.
When you want to use the toner
container currently installed,
press [OK] and [Stop/Reset]
simultaneously for 3 seconds or
more.
Paper Jam. (DP) Paper jam A paper jam has occurred in
the document processor. Refer to Clearing Paper Jams
on page 9-14 and remove the
jammed paper.
PaperJam.
(RearCover) Paper jam A paper jam has occurred. Refer to Clearing Paper Jams
on page 9-14 and remove the
jammed paper.
Place original and
press Start key. Add paper — Place the original in the
document processor again and
press [Start].
Message Display Message displayed in
KYOCERA Client Tool and
Status Monitor* Meaning Remedy
9-10
Troubleshooting
Remove original in
document
processor.
Error has occurred An original remains in the
document processor. Remove originals from the
document processor, put them
back in their original order, and
place them again. Press [OK]
to resume printing. Press
[Stop/Reset] to cancel the job.
Remove the paper
from the inner
tray.
Inner tray full The inner tray is full of
paper. The machine pauses after 100
sheets are printed. Remove
paper from the inner tray and
press [OK] to resume printing.
Replace MK. Replacing the
Maintenance Kit Replacement of the
maintenance kit is
necessary at every 100,000
images of printing.
Replace Maintenance Kit.
Scanner memory is
full. Memory full Scanning cannot be
performed due to insufficient
memory of scanner.
Only the scanned pages are
available. Press [OK] and the
job will be canceled.
Scheduled sending
jobs exceeded. Error has occurred The number of the
scheduled transmission jobs
has exceeded the limit.
Wait until the scheduled
transmission is executed, or
cancel the scheduled
transmission and then perform
the job again.
Set paper in MF
tray and press OK
key.
Add paper Paper is not set in the
Manual Feed tray. Load paper into the Manual
Feed tray and press [OK] to
begin printing.
Toner is running
out. Toner is running out. It is almost time to replace
the toner container. Obtain a new toner container.
Unknown toner
installed.PC Error has occurred The installed toner
container's regional
specification does not match
the machine’s.
Install the specified toner
container.
USB cable was
disconnected. — The USB cable is not
connected. Press [OK] and connect the
USB cable.
The PC is powered off. Press [OK] and turn the PC
power on.
Cannot find KYOCERA
Client Tool. Press [OK] and open
KYOCERA Client Tool.
—Not connected. The USB cable is not
connected. Connect the USB cable.
The network cable is not
connected. Connect the network cable.
The machine is powered off. Turn the machine power on.
Cannot find the appropriate
driver. Install the appropriate driver.
Message Display Message displayed in
KYOCERA Client Tool and
Status Monitor* Meaning Remedy
9-11
Troubleshooting
—Limited availability for
jobs Unusable Time is in effect. To use the machine temporarily
during Unusable Time, enter
the unlock code. For details,
refer to Unusable Time on
page 7-35.
* Events for which the Status Monitor provides notification can be set in the Configuration. Refer to Configuration
on page 2-48.
Message Display Message displayed in
KYOCERA Client Tool and
Status Monitor* Meaning Remedy
9-12
Troubleshooting
FAX Error Code List
When a FAX communication error occurs, one of the following error codes is recorded in the FAX TX/RX Result or
Outgoing/Incoming FAX Report.
Note “U” or “E” will appear in the error code depending on the communication speed setting.
Error Code Possible Cause/Action
Busy Failed to establish connection with the recipient despite auto redialing the preset number of
times. Send again.
CANCELED Transmission was canceled due to an action to cancel transmission.
Reception was canceled due to an action to cancel reception.
U00300 Paper depletion occurred at the recipient machine. Check with the recipient.
U00430 - U00462 Reception was canceled because of mismatching of communication features with the sender
machine although the line connection was established.
U00601 - U00690 Communication was stopped due to the machine failure. Send or receive again.
U00700 Communication was stopped due to failure on the part of the sender or recipient machine.
U00800 - U00811 Page(s) not sent correctly. Send again.
If you still have trouble, reduce TX Start Speed and send again.
Note If the communication error occurs frequently, change the default setting of TX Start
Speed in System Menu.
U00900 - U00910 Page(s) not received correctly. Ask the sender to resend.
Note If the communication error occurs frequently, change the default setting of RX Start
Speed in System Menu.
U01000 - U01097 Communication error occurred during transmission. Send again.
If you still have trouble, reduce TX Start Speed and send again.
Note If the communication error occurs frequently, change the default setting of TX Start
Speed in System Menu.
U01100 - U01196 Communication error occurred during reception. Ask the sender to resend.
Note If the communication error occurs frequently, change the default setting of RX Start
Speed in System Menu.
U01400 Failed to establish communication with the sender or recipient machine because dialing
registered for a push line system was used in a pulse line system.
U01500 Communication error occurred during high-speed transmission. Send again.
If you still have trouble, reduce TX Start Speed and send again.
Note If the communication error occurs frequently, change the default setting of TX Start
Speed in System Menu.
U01600 Communication error occurred during reception of high-speed transmission. Ask the sender
to reduce the transmission speed and send again.
Note If the communication error occurs frequently, change the default setting of RX Start
Speed in System Menu.
U01700 - U01720 Communication error occurred during high-speed transmission. Send again.
If you still have trouble, reduce TX Start Speed and send again.
Note If the communication error occurs frequently, change the default setting of TX Start
Speed in System Menu.
9-13
Troubleshooting
U01721 Communication error occurred during high-speed transmission. Designated transmission
speed may not be available for the recipient machine.
Reduce the transmission start speed and send again.
U01800 - U01820 Communication error occurred during reception of high-speed transmission. Ask the sender
to reduce the transmission speed and send again.
Note If the communication error occurs frequently, change the default setting of RX Start
Speed in System Menu.
U01821 Communication error occurred during reception of high-speed transmission. Designated
transmission speed may not be available for this machine. Ask the sender to reduce the
transmission speed and send again.
Note If the communication error occurs frequently, change the default setting of RX Start
Speed in System Menu.
U05200 Reception was canceled because communication requirements are not met due to the
reception restriction set on this machine.
U05300 Reception was rejected by the recipient because communication requirements are not met
due to the reception restriction set on the recipient machine. Check with the recipient.
U19000 Memory reception was stopped because there is no more free space in the memory of this
machine.
Create free space by outputting t he dat a stored in the memory, and ask the sender to resend.
U19100 Transmission was stopped because there is no more free space in the memory of the
recipient machine. Check with the recipient.
Error Code Possible Cause/Action
9-14
Troubleshooting
Clearing Paper Jams
If paper jams in the paper transport system, or no paper sheets are fed at all, the machine automatically goes offline, and
the Attention indicator will flash. KYOCERA Client Tool can indicate the location of the paper jam (the component where
the paper jam has occurred). Remove the paper jam. After removing the paper jam, the machine will resume printing.
Possible Paper Jam Locations
Detailed paper jam positions are as follows. Refer to the indicated page number to remove the paper jam.
General Considerations for Clearing Jams
Bear in mind the following considerations when attempting paper jam removal:
•If paper jams occur frequently, try using a different type of paper, replace the paper with paper from another ream, or
flip the paper stack over. The machine may have problems if paper jams recur after the paper is replaced.
•Whether or not the jammed pages are reproduced normally after printing is resumed, depends on the location of the
paper jam.
Paper Jam
Locations Error Message Message displayed in
KYOCERA Client Tool
and Status Monitor Description Reference
page
APaperJam.
(RearCover) Paper jam A paper jam has occurred in the rear
cover. 9-15, 9-16
BCannot feed paper.*
*Cannot feed paper. also appears when the paper has run out. In this case, add paper. Refer to Loading
Paper
on page 2-5.
Add paper A paper jam has occurred in the
cassette. 9-17, 9-18
CA paper jam has occurred in the
Manual Feed tray. 9-19
DPaper Jam. (DP) Paper jam A paper jam has occurred in the
document processor. 9-20
CAUTION When removing a p aper jam, pull the pap er gently so as not to tear it. T orn pieces of p aper are
difficult to remove and may be easily overlooked, deterring the paper jam recover y.
A
B
C
D
9-15
Troubleshooting
Rear Cover
Follow the steps below to clear paper jams inside the rear cover.
Note When the front cover is opened or closed, the paper inside the
machine may be discharged.
1
2
1
2
2
4
1
3
IMPORTANT Take care
not to touch the drum and
transfer roller (black).
Drum
Transfer Roller
(FS-1025MFP, FS-1125MFP and FS-1325MFP)
9-16
Troubleshooting
6
5
7
1
2
1
2
CAUTION The fuser unit inside the
machine is hot. Do not touch it, as it
may result in burn injury.
Note Close the top cover first and then close
the rear cover. Note When printing by manual feeding, press
[OK].
Close the rear cover to clear the error. The
machine warms up and resumes printing.
9-16
9-17
Troubleshooting
Cassette
Follow the steps below to clear paper jams in the cassette.
IMPORTANT Do not try to remove paper that has already been partially fed. Refer to Rear Cover on page 9-15.
Note Do not open or close the front cover or rear cover before removing the jammed paper.
1 2
3
54
Remove any partially fed paper.
Check to see if paper is loaded
correctly. If not, reload the paper.
Press [OK] to clear the error and
the machine warms up and
resumes printing.
9-18
Troubleshooting
If paper feed failure occurs
Check on and reduction of number of paper sheets loaded
If an excessive amount of thick paper is loaded in the cassette, it may not be fed. In that case,
reduce the number of sheets to be loaded.
Edge fanning and curl straightening
Remove all the even pages (including the instruction sheet) from the inner tray, fan through the
sheets to separate them prior to loading.
If the paper is curled at an edge, straighten it prior to reloading.
No paper feed due to wavy paper edge
When the paper feed fails because the edge of the pap er is wavy, turn it upside down and load
it again.
9-19
Troubleshooting
Manual Feed Tray (FS-1025MFP, FS-1125MFP and FS-1325MFP)
Follow the steps below to clear paper jams in the Manual Feed tray.
IMPORTANT Do not try to remove paper that has already been partially fed. Refer to Rear Cover on page 9-15.
Note Do not open or close the front cover or rear cover before removing the jammed paper.
1
2
3
Remove the paper jammed at the
Manual Feed tray.
Reload the Manual Feed tray.
Press [OK] to clear the error and
the machine warms up and
resumes printing.
9-20
Troubleshooting
Document Processor
Follow the steps below to clear paper jams in the document processor.
Note Do not open or close the front cover or rear cover before removing the jammed paper.
12
34
56
10-1
10 Appendix
This chapter explains the following topics:
Character Entry Method ...................................................................................................................................... 10-2
Specifications....................................................................................................................................................... 10-5
10-2
Appendix
Character Entry Method
Use the procedure below to enter characters.
Keys Used
Characters that can be entered with the Numeric Keys
The characters shown below can be entered with the numeric keys.
Keys Entered character (changes to the next character on the right each time the key is pressed)
.@-_/:~1(Repeats from the first character on the left)
1 (During number entry)
abcABC2(Repeats from the first character on the left)
2 (During number entry)
defDEF3(Repeats from the first character on the left)
3 (During number entry)
ghiGHI4(Repeats from the first character on the left)
4 (During number entry)
jklJKL5(Repeats from the first character on the left)
5 (During number entry)
mnoMNO6(Repeats from the first character on the left)
6 (During number entry)
Local FAX Name
b
R
a
[] key Moves the cursor to the left.
[] key Moves the cursor to the right. Also
used to enter a space.
Note It is not possible to move the cursor when
entering numbers.
Message
Display Displays the characters that have been
entered.
[Clear] key Deletes entered characters.
[OK] key Use to complete input.
When entering a symbol, use to enter
the selected symbol.
Numeric
Keys Use to enter characters and symbols.
Cursor A character is entered in the position
marked by the cursor.
10-3
Appendix
Entering Symbols
Symbols can be entered.
1Press [#]. Displays the symbol list.
2Press [▲] or [▼] to move the cursor and select the symbol to be entered.
3Press [OK]. The selected symbol is entered.
Entering Characters
Follow the steps below to enter ‘R&D’ for an example.
1Press [7]. ‘r’ is entered.
2Press [*/.]. ‘r’ changes to ‘R’.
pqrsPQRS7(Repeats from the first character on the left)
7 (During number entry)
tuvTUV8(Repeats from the first character on the left)
8 (During number entry)
wxyzWXYZ9(Repeats from the first character on the left)
9 (During number entry)
.,-_‘!?(space) 0(Repeats from the first character on the left)
0 (During number entry)
Switches the character marked by the cursor between upper case and lower case.
[*] or [.] (During number entry)
!"#$%&'()*+,-.Displays the symbol list. For
details, refer to Entering
Symbols
on page 10-3.
/:;<=>?@[\]^_`
{|}~
# (During number entry)
Keys Entered character (changes to the next character on the right each time the key is pressed)
Local FAX Name
b
"#$%&'()*+,-.
!
Local FAX Name
b
!"#$% '()*+,-.
&
Local FAX Name
b
R&
Local FAX Name
b
r
Local FAX Name
b
R
10-4
Appendix
3Press []. The cursor moves to the right.
4Press [#]. Displays the symbol list.
5Press [▲] or [▼] to move the cursor and select ‘&’.
6Press [OK]. ‘&’ is entered.
7Press [3] four times. ‘D’ is entered.
8Press [].
Local FAX Name
b
R
Symbol
b
"#$%&'()*+,-.
!
Symbol
b
!"#$% '()*+,-.
&
Local FAX Name
b
R&
Local FAX Name
b
R&
D
Local FAX Name
b
R&D
10-5
Appendix
Specifications
Common Functions
Note These specifications are subject to change without notice.
Item
Description
FS-1120MFP/
FS-1320MFP FS-1025MFP FS-1125MFP/
FS-1325MFP
Type Desktop
Printing Method Electrophotography by semiconductor laser
Paper Weight Cassette 60 to 220 g/m²
Manual Feed
Tray* — 60 to 220 g/m²
Paper Type Plain, Preprinted, Labels, Bond, Recycled, Vellum, Rough, Letterhead, Color,
Prepunched, Envelope, Cardstock, Thick paper, High Quality, Custom 1 to 8
Warm-up Time
(22°C/71.6°F,
60%RH)
Power on 28 seconds or less 23 seconds or less 28 seconds or less
Sleep 12 seconds or less 14 seconds or less
Paper Capacity Cassette 250 sheets (80 g/m²)
Manual Feed
Tray* — 1 sheet
Inner Tray
Capacity Standard paper 100 sheets (80 g/m²) (The machine pauses after 100 sheets are printed.)
Special paper 1 sheet
Continuous Copying 1 to 99 sheets
Image Write System Semiconductor laser and electrophotography
Memory ROM: 32 MB / RAM: 64 MB
Interface USB Interface
Connector: 1 (Hi-Speed
USB)
USB Interface Connector: 1 (Hi-Speed USB)
Network Interface: 1 (10 BASE-T/100 BASE-TX
[TCP/IP, WSD]) <This unit does not support the
NetBEUI.>
Operating
Environment Temperature 10 to 32.5°C/50 to 90.5°F
Humidity 15 to 80%
Altitude 3,500 m/11,482.8 ft maximum
Brightness 1,500 lux maximum
Dimension (W × D × H) 390 × 361 × 362 mm
15-3/8 × 14-3/16 × 14-1/4"
Weight (with toner container) 9.7 kg/21.34 lb 10.0 kg/22 lb 10.1 kg/22.22 lb
Space Required (W × D) 424 × 645 mm
16-11/16 × 25-3/8"
424 × 630 mm
16-11/16 × 24-13/16"
Power Requirements 230 V Specification Model: 220 to 240 V (50 Hz/60 Hz, 3.1 A)
120 V Specification Model:120 V (60 Hz, 6.0 A)
* The Manual Feed tray is only provided on the FS-1025MFP, FS-1125MFP and FS-1325MFP.
10-6
Appendix
Copy Functions
Item
Description
FS-1120MFP/FS-1320MFP FS-1025MFP FS-1125MFP/
FS-1325MFP
Paper Size Cassette A4, A5, A6, Folio, JIS B5, ISO B5, Letter, Legal, Statement, Executive, Oficio II
(216 × 340 mm, 8-1/2 × 13 inches), 216 × 340 mm, 16 K, Custom (70 × 148 to
216 × 356 mm, 2-3/4 × 5-13/16 to 8-1/2 × 14 inches)
Manual Feed
Tray* — A4, A5, A6, Folio, JIS B5, ISO B5, Letter,
Legal, Statement, Executive, Oficio II
(216 × 340 mm, 8-1/2 × 13 inches), 216 ×
340 mm, 16 K, Custom (70 × 148 to
216 × 356 mm, 2-3/4 × 5-13/16 to
8-1/2 × 14 inches)
Copying Speed
(feed from
cassette)
(images/min)
(300 × 300 dpi)
When not using the document processor
A4 Light (63 g/m² or less): 20
Normal 1 (64 to 69 g/m²): 20
Normal 2 (3) (70 to 105 g/m²): 20
Light (63 g/m² or less): 25
Normal 1 (64 to 69 g/m²): 25
Normal 2 (3) (70 to 105 g/m²): 25
A4 (Quiet Mode) Light (63 g/m² or less): 15
Normal 1 (64 to 69 g/m²): 15
Normal 2 (3) (70 to 105 g/m²): 15
Heavy 1 (106 to 135 g/m²): 14
Heavy 2 (3) (136 to 220 g/m²): 13
Light (63 g/m² or less): 18
Normal 1 (64 to 69 g/m²): 18
Normal 2 (3) (70 to 105 g/m²): 18
Heavy 1 (106 to 135 g/m²): 17
Heavy 2 (3) (136 to 220 g/m²): 16
Letter Light (63 g/m² or less): 21
Normal 1 (64 to 69 g/m²): 21
Normal 2 (3) (70 to 105 g/m²): 21
Light (63 g/m² or less): 26
Normal 1 (64 to 69 g/m²): 26
Normal 2 (3) (70 to 105 g/m²): 26
Letter
(Quiet Mode)
Light (63 g/m² or less): 16
Normal 1 (64 to 69 g/m²): 16
Normal 2 (3) (70 to 105 g/m²): 16
Heavy 1 (106 to 135 g/m²): 14
Heavy 2 (3) (136 to 220 g/m²):13
Light (63 g/m² or less): 19
Normal 1 (64 to 69 g/m²): 19
Normal 2 (3) (70 to 105 g/m²): 19
Heavy 1 (106 to 135 g/m²): 17
Heavy 2 (3) (136 to 220 g/m²):16
A5/B5/A6
(Quiet Mode)
Light (63 g/m² or less): 12
Normal 1 (64 to 69 g/m²): 12
Normal 2 (3) (70 to 105 g/m²): 12
Heavy 1 (106 to 135 g/m²): 10
Heavy 2 (3) (136 to 220 g/m²): 9
Light (63 g/m² or less): 15
Normal 1 (64 to 69 g/m²): 15
Normal 2 (3) (70 to 105 g/m²): 15
Heavy 1 (106 to 135 g/m²): 13
Heavy 2 (3) (136 to 220 g/m²): 12
A5/B5/A6 (from
11th image)
(Quiet Mode)
Light (63 g/m² or less): 10
Normal 1 (64 to 69 g/m²): 10
Normal 2 (3) (70 to 105 g/m²): 10
Heavy 1 (106 to 135 g/m²): 8
Heavy 2 (3) (136 to 220 g/m²): 8
Light (63 g/m² or less): 12
Normal 1 (64 to 69 g/m²): 12
Normal 2 (3) (70 to 105 g/m²): 12
Heavy 1 (106 to 135 g/m²): 11
Heavy 2 (3) (136 to 220 g/m²): 10
When using the document processor
A4 Light (63 g/m² or less): 20
Normal 1 (64 to 69 g/m²): 20
Normal 2 (3) (70 to 105 g/m²): 20
Light (63 g/m² or less): 20
Normal 1 (64 to 69 g/m²): 20
Normal 2 (3) (70 to 105 g/m²): 20
* The Manual Feed tray is only provided on the FS-1025MFP, FS-1125MFP and FS-1325MFP.
10-7
Appendix
Item
Description
FS-1120MFP/FS-1320MFP FS-1025MFP FS-1125MFP/
FS-1325MFP
Copying Speed
(feed from
cassette)
(images/min)
(300 × 300 dpi)
A4 (Quiet Mode) Light (63 g/m² or less): 15
Normal 1 (64 to 69 g/m²): 15
Normal 2 (3) (70 to 105 g/m²): 15
Heavy 1 (106 to 135 g/m²): 14
Heavy 2 (3) (136 to 220 g/m²): 13
Light (63 g/m² or less): 18
Normal 1 (64 to 69 g/m²): 18
Normal 2 (3) (70 to 105 g/m²): 18
Heavy 1 (106 to 135 g/m²): 17
Heavy 2 (3) (136 to 220 g/m²): 16
Letter Light (63 g/m² or less): 21
Normal 1 (64 to 69 g/m²): 21
Normal 2 (3) (70 to 105 g/m²): 21
Light (63 g/m² or less): 21
Normal 1 (64 to 69 g/m²): 21
Normal 2 (3) (70 to 105 g/m²): 21
Letter
(Quiet Mode)
Light (63 g/m² or less): 16
Normal 1 (64 to 69 g/m²): 16
Normal 2 (3) (70 to 105 g/m²): 16
Heavy 1 (106 to 135 g/m²): 14
Heavy 2 (3) (136 to 220 g/m²):13
Light (63 g/m² or less): 19
Normal 1 (64 to 69 g/m²): 19
Normal 2 (3) (70 to 105 g/m²): 19
Heavy 1 (106 to 135 g/m²): 17
Heavy 2 (3) (136 to 220 g/m²):16
A5/B5/A6
(Quiet Mode)
Light (63 g/m² or less): 12
Normal 1 (64 to 69 g/m²): 12
Normal 2 (3) (70 to 105 g/m²): 12
Heavy 1 (106 to 135 g/m²): 10
Heavy 2 (3) (136 to 220 g/m²): 9
Light (63 g/m² or less): 15
Normal 1 (64 to 69 g/m²): 15
Normal 2 (3) (70 to 105 g/m²): 15
Heavy 1 (106 to 135 g/m²): 13
Heavy 2 (3) (136 to 220 g/m²): 12
A5/B5/A6 (from
11th image)
(Quiet Mode)
Light (63 g/m² or less): 10
Normal 1 (64 to 69 g/m²): 10
Normal 2 (3) (70 to 105 g/m²): 10
Heavy 1 (106 to 135 g/m²): 8
Heavy 2 (3) (136 to 220 g/m²): 8
Light (63 g/m² or less): 12
Normal 1 (64 to 69 g/m²): 12
Normal 2 (3) (70 to 105 g/m²): 12
Heavy 1 (106 to 135 g/m²): 11
Heavy 2 (3) (136 to 220 g/m²): 10
Legal Light (63 g/m² or less): 13
Normal 1 (64 to 69 g/m²): 13
Normal 2 (3) (70 to 105 g/m²): 13
Light (63 g/m² or less): 16
Normal 1 (64 to 69 g/m²): 16
Normal 2 (3) (70 to 105 g/m²): 16
Legal
(Quiet Mode)
Light (63 g/m² or less): 12
Normal 1 (64 to 69 g/m²): 12
Normal 2 (3) (70 to 105 g/m²): 12
Heavy 1 (106 to 135 g/m²): 11
Heavy 2 (3) (136 to 220 g/m²): 10
Light (63 g/m² or less): 15
Normal 1 (64 to 69 g/m²): 15
Normal 2 (3) (70 to 105 g/m²): 15
Heavy 1 (106 to 135 g/m²): 13
Heavy 2 (3) (136 to 220 g/m²): 11
First Print Time
(A4, feed from
cassette)
When not using
the document
processor
12 seconds or less 11 seconds or less
When using the
document
processor
14 seconds or less 13 seconds or less
Zoom Level 25 to 400%, 1% increments
Resolution 600 × 600 dpi
Supported Original Types Sheet, Book, 3-dimensional objects (maximum original size: A4/Letter)
Original Feed System Fixed
10-8
Appendix
Printer Functions
Item
Description
FS-1120MFP/FS-1320MFP FS-1025MFP FS-1125MFP/
FS-1325MFP
Paper Size Cassette A4, A5, A6, Folio, JIS B5, ISO B5, Letter , Legal, S tatement, Executive, Envelope
Monarch, Envelope #10, Envelope #9, Envelope #6-3/4, Envelope C5,
Envelope DL, Oficio II (216 × 340 mm, 8-1/2 × 13 inches), 216 × 340 mm, 16 K,
Custom (70 × 148 to 216 × 356 mm, 2-3/4 × 5-13/16 to 8-1/2 × 14 inches)
Manual Feed
Tray* — A4, A5, A6, Folio, JIS B5, ISO B5, Letter,
Legal, Statement, Executive, Envelope
Monarch, Envelope #10, Envelope #9,
Envelope #6-3/4, Envelope C5, Envelope
DL, Oficio II (216 × 340 mm,
8-1/2 × 13 inches), 216 × 340 mm, 16 K,
Custom (70 × 148 to 216 × 356 mm,
2-3/4 × 5-13/16 to 8-1/2 × 14 inches)
Printing Speed
(images/min)
A4 Light (63 g/m² or less): 20
Normal 1 (64 to 69 g/m²): 20
Normal 2 (3) (70 to 105 g/m²): 20
Light (63 g/m² or less): 25
Normal 1 (64 to 69 g/m²): 25
Normal 2 (3) (70 to 105 g/m²): 25
A4 (Quiet Mode) Light (63 g/m² or less): 15
Normal 1 (64 to 69 g/m²): 15
Normal 2 (3) (70 to 105 g/m²): 15
Heavy 1 (106 to 135 g/m²): 14
Heavy 2 (3) (136 to 220 g/m²): 13
Light (63 g/m² or less): 18
Normal 1 (64 to 69 g/m²): 18
Normal 2 (3) (70 to 105 g/m²): 18
Heavy 1 (106 to 135 g/m²): 17
Heavy 2 (3) (136 to 220 g/m²): 16
Letter Light (63 g/m² or less): 21
Normal 1 (64 to 69 g/m²): 21
Normal 2 (3) (70 to 105 g/m²): 21
Light (63 g/m² or less): 26
Normal 1 (64 to 69 g/m²): 26
Normal 2 (3) (70 to 105 g/m²): 26
Letter
(Quiet Mode)
Light (63 g/m² or less): 16
Normal 1 (64 to 69 g/m²): 16
Normal 2 (3) (70 to 105 g/m²): 16
Heavy 1 (106 to 135 g/m²): 14
Heavy 2 (3) (136 to 220 g/m²):13
Light (63 g/m² or less): 19
Normal 1 (64 to 69 g/m²): 19
Normal 2 (3) (70 to 105 g/m²): 19
Heavy 1 (106 to 135 g/m²): 17
Heavy 2 (3) (136 to 220 g/m²):16
A5/B5/A6
(Quiet Mode)
Light (63 g/m² or less): 12
Normal 1 (64 to 69 g/m²): 12
Normal 2 (3) (70 to 105 g/m²): 12
Heavy 1 (106 to 135 g/m²): 10
Heavy 2 (3) (136 to 220 g/m²): 9
Light (63 g/m² or less): 15
Normal 1 (64 to 69 g/m²): 15
Normal 2 (3) (70 to 105 g/m²): 15
Heavy 1 (106 to 135 g/m²): 13
Heavy 2 (3) (136 to 220 g/m²): 12
A5/B5/A6 (from
11th image)
(Quiet Mode)
Light (63 g/m² or less): 10
Normal 1 (64 to 69 g/m²): 10
Normal 2 (3) (70 to 105 g/m²): 10
Heavy 1 (106 to 135 g/m²): 8
Heavy 2 (3) (136 to 220 g/m²): 8
Light (63 g/m² or less): 12
Normal 1 (64 to 69 g/m²): 12
Normal 2 (3) (70 to 105 g/m²): 12
Heavy 1 (106 to 135 g/m²): 11
Heavy 2 (3) (136 to 220 g/m²): 10
Legal Light (63 g/m² or less): 13
Normal 1 (64 to 69 g/m²): 13
Normal 2 (3) (70 to 105 g/m²): 13
Light (63 g/m² or less): 20
Normal 1 (64 to 69 g/m²): 20
Normal 2 (3) (70 to 105 g/m²): 20
* The Manual Feed tray is only provided on the FS-1025MFP, FS-1125MFP and FS-1325MFP.
10-9
Appendix
Item
Description
FS-1120MFP/FS-1320MFP FS-1025MFP FS-1125MFP/
FS-1325MFP
Printing Speed
(images/min)
Legal
(Quiet Mode)
Light (63 g/m² or less): 12
Normal 1 (64 to 69 g/m²): 12
Normal 2 (3) (70 to 105 g/m²): 12
Heavy 1 (106 to 135 g/m²): 11
Heavy 2 (3) (136 to 220 g/m²): 10
Light (63 g/m² or less): 15
Normal 1 (64 to 69 g/m²): 15
Normal 2 (3) (70 to 105 g/m²): 15
Heavy 1 (106 to 135 g/m²): 13
Heavy 2 (3) (136 to 220 g/m²): 11
Duplex Printing
Speed*
(images/min)
A4 — Light (63 g/m² or less): 15
Normal 1 (64 to 69 g/m²): 15
Normal 2 (3) (70 to 105 g/m²): 15
A4 (Quiet Mode) — Light (63 g/m² or less): 11
Normal 1 (64 to 69 g/m²): 11
Normal 2 (3) (70 to 105 g/m²): 11
Heavy 1 (106 to 135 g/m²): 11
Heavy 2 (3) (136 to 220 g/m²): 11
Letter — Light (63 g/m² or less): 15
Normal 1 (64 to 69 g/m²): 15
Normal 2 (3) (70 to 105 g/m²): 15
Letter
(Quiet Mode)
— Light (63 g/m² or less): 11
Normal 1 (64 to 69 g/m²): 11
Normal 2 (3) (70 to 105 g/m²): 11
Heavy 1 (106 to 135 g/m²): 11
Heavy 2 (3) (136 to 220 g/m²): 11
Legal — Light (63 g/m² or less): 13
Normal 1 (64 to 69 g/m²): 13
Normal 2 (3) (70 to 105 g/m²): 13
Legal
(Quiet Mode)
— Light (63 g/m² or less): 10
Normal 1 (64 to 69 g/m²): 10
Normal 2 (3) (70 to 105 g/m²): 10
Heavy 1 (106 to 135 g/m²): 9
Heavy 2 (3) (136 to 220 g/m²): 9
First Print T ime
(A4, feed from Cassette)
8.5 seconds or less 7.5 seconds or less
Resolution 600 × 600 dpi/Fast 1200 dpi
Controller ARM926EJ 390MHz
Supported OS Windows XP, Windows Server 2003/R2, Windows Vista, Windows 7, Windows
Server 2008/R2, Mac OS X 10.5 or higher
* Duplex printing is only possible on the FS-1025MFP, FS-1125MFP and FS-1325MFP.
10-10
Appendix
Scanner Functions
FAX Functions
Item Description
System Requirements CPU: 20 MHz
RAM: 64 MB
Resolution 200 × 200 dpi, 300 × 300 dpi, 400 × 400 dpi, 600 × 600 dpi
File Format BMP, JPEG, PNG, TIFF, PDF
Scanning Speed (A4 landscape,
300 dpi) B/W: 18 Images/min
Color: 6 Images/min
Transmission System PC transmission: Scan to Folder
TWAIN scan*
WIA scan**
* Available Operating System: Windows XP, Windows Server 2003/R2, Windows Vista, Windows 7, Windows
Server 2008/R2
** Available Operating System: Windows Vista, Windows 7, Windows Server 2008/R2
Item Description
FS-1120MFP/FS-1320MFP FS-1125MFP/FS-1325MFP
Paper Size Cassette A4, Folio, Letter, Legal
Manual Feed Tray* — A4, Folio, Letter, Legal
Compatibility G3
Communication Line Subscriber telephone line
Transmission Time 4 seconds or less (MMR, ITU-T A4-R #1 chart)
Transmission Speed 33600/31200/28800/26400/24000/21600/19200/16800/14400/12000/9600/720
0/4800/2400 bps
Coding Scheme MMR/MR/MH
Error Correction ECM
Original Size Max. width: 216 mm/8-1/2", Max. length: 356 mm/14"
Scanner Resolution Horizontal × Vertical
Normal (8 dot/mm × 3.85 line/mm)
Fine (8 dot/mm × 7.7 line/mm)
Super Fine (8 dot/mm × 15.4 line/mm)
Gradations 256 shades (Error diffusion)
Multi-Station Transmission Max. 100 destinations
Substitute Memory Reception 150 sheets or more (when using ITU-T A4 #1)
Report Output S t atus Page, Network Status, Outgoing FAX Report, Incoming FAX Report, F AX
RX Result, FAX TX Result
* The Manual Feed tray is only provided on the FS-1125MFP and FS-1325MFP.
10-11
Appendix
Document Processor
Item Description
Original Feed Method Automatic feed
Supported Original Types Sheet originals
Paper Size Maximum: Folio/Legal, Minimum: A6/Statement-R
Paper Weight 60 to 105 g/m²
Loading Capacity 40 sheets (80 g/m²) maximum
10-12
Appendix
Index-1
Index
A
Address Book ............................................................... 2-39
reject list ................................................................ 2-43
Adhesive label ............................................................... . 2-9
Administrator ID ................... ... ........................................ 6-6
C
Cassette
basis weight ....................... ................ ..................... 2-7
clearing paper jams ............................................... 9-17
components ............ ............................................. .... 1- 2
loading paper ......................................................... 2-13
minimum and maximum page sizes ............... ......... 2-6
paper sizes ............. ... ............................... ............... 2-6
paper type ............................................................. 2-12
Cassette cover ............................................................. 2-16
components ............ ............................................. .... 1- 2
Character entry method ................................................ 10-2
Cleaning
document processor, platen .................. ... ............... 8-5
interior of the machine ................ ............................. 8-6
slit glass cover .................................... ..................... 8-6
Clearing paper jams ..................................................... 9-14
cassette ................................................................. 9-17
Manual Feed tray .................................................. 9-19
possible paper jam locati ons ................................. 9-14
rear cover section .................................................. 9-15
Collate ............................................... ............................. 3-6
Colored paper ............................................................... 2-11
Combine ................ ............................................. ............ 3-9
Components
at the front of the machine ................. ..................... 1-2
at the rear of the machine ....... ... ................. ............ 1-3
Configuration ................................................................ 2-48
Communication tab ............................................... 2-55
Copy tab ................................................................ 2-52
Device Defaults tab ............................................... 2-50
FAX tab .................................................................. 2-53
SNMP Traps tab .................................................... 2-56
Status Monitor tab ................................................. 2-57
Connection
FAX modular cord ...................... ............................. 2-3
network cable ............... ... ............................... ......... 2-2
power cord ................... ... ........................................ 2-3
USB cable ............................... ................................ 2-2
Copying ................. ... ............................................. ......... 3-1
basic operati on ......................................... ............... 3-2
collate ............................................................. ......... 3-6
combine ......................................... .......................... 3-9
duplex ............. ............................................. ............ 3-6
EcoPrint ................................................................. 3-12
ID Card Copy ........................................................ 3-13
manual duplex ............................... .......................... 3-3
original image ........................................................ 3-12
original orientation ................................................. 3-11
original size ........................................................... 3-10
programs ................................................................. 3-5
zoom ........................................................................ 3-7
D
Default settings ............. ... ............................................. 2-32
Document processor
cleaning ................................................................... 8-5
components ............................................................. 1-2
loading originals ............. ... ..................................... 2-18
Duplex ............................................................................. 3-6
E
EcoPrint .......................................................... .............. 3-12
Energy Star ........................................................................ vi
Envelopes ....................................................... .............. 2-10
Error messages .............................................................. 9-8
F
FAX ................................................................................. 7-1
automatic reception ................ ............................... 7-21
chain dial .......................... ..................................... 7-19
entering the destination ........................................... 7-7
forward settings ................... ... ................. .............. 7-28
local FAX information entry ...................................... 7-3
manual send ........................ .................................. 7-18
programs .................... ................. .......................... 7-15
receiving .......... ................. ..................................... 7-21
redial .......................................................... ............ 7-11
reports ................... ... ............................... .............. 7-23
RX restriction ................. ................. ....................... 7-34
sending ......... ... ............................................. ......... 7-12
setting date and time ............................................... 7-2
settings ............................................................ ...... 7-24
transmission functions ............ ................. .............. 7-16
FAX Address Book Utility ................................ .............. 2-39
FAX driver ..................... ... ............................................. 7-37
FAX error code list ................... ............................... ...... 9-12
FAX modular cord
connection ............................................................... 2-3
Front cover
components ............................................................. 1-2
I
ID Card Copy ................................... ............................. 3-13
Indicator
Attention .................................................................. 1-4
Processing ............................................................... 1-4
Inner tray
components ............................................................. 1-2
Install the software
Macintosh ................. .. ............................... ............ 2-23
Windows ........................... ..................................... 2-21
Instruction sheet
Index-2
manual duplex ............................... .......................... 4-5
K
Key Address Book ..................... .. ............................... .... 1- 4
Address Recall/Pause ............. ... ............................. 1-4
Back ...... ................. ............................................. .... 1- 4
Clear .................... ............................... ..................... 1-4
Copy .................. ............................... ....................... 1-4
Density ................... ... ............................................. . 1-4
FAX ............. ... ............................................. ............ 1-4
ID Card Copy ..................................... ..................... 1-4
Menu .............. ................. ........................................ 1-4
Numeric ............... ............................... ..................... 1-4
OK ..................... ............................................. ......... 1-4
On Hook ................................................................. . 1-4
Print Box .................................. ................................ 1-4
Program ..................................... ............................. 1-4
Quiet Mode ...................... ........................................ 1-4
Scan .................. .. ............................... ..................... 1-4
Start ........................... ............................................. . 1-4
Stop/Reset ................. ... ........................................... 1-4
KYOCERA Client Tool .................................................. 2-26
L
Label ........................................................ ....................... 2-9
LINE connector
components ............ ............................................. .... 1- 3
Loading originals
document processor .............................................. 2-18
platen .................................................................... 2-18
Loading paper
cassette ................................................................. 2-13
Manual Feed tray .................................................. 2-16
M
Machine parts ................ ............................................. .... 1-1
Maintenance .................. ... ............................................. . 8-1
cleaning ..................... ............................... ............... 8-5
maintenance kit replacement ...................... ............ 8-5
maintenance menu ............. ................ ..................... 8-8
toner container replacement .................................... 8-2
Maintenance kit
replacement ................. ........................................... 8-5
Maintenance menu .............. ........................................... 8-8
Manual duplex
copying .................................... ................................ 3-3
printing .............. .. ............................................. ....... 4-4
Manual feed ................ ............................................. ....... 4-3
Manual Feed tray
basis weight ....................... ................ ..................... 2-7
clearing paper jams ............................................... 9-19
components ............ ............................................. .... 1- 2
loading paper ......................................................... 2-16
minimum and maximum paper sizes ....................... 2-6
paper sizes ............. ... ............................... ............... 2-6
paper type ............................................................. 2-12
Manual send ................................................................. 7-18
Message display ............................................................. 1-4
Moving the machine ........................................................ 8-9
N
Network cable
connection ............................................................... 2-2
Network interface connector
components ............................................................. 1-3
O
Operation panel
components ............................................................. 1-2
indicators, keys, overview ........................................ 1-4
Orientation image ............ .. ........................................... 3-11
Original image ............................................................ ... 3-12
Original size ......................................................... ......... 3-10
Original size indicator plates
components ............................................................. 1-2
Original table
components ............................................................. 1-2
Original width guides
components ............................................................. 1-2
P
Paper
minimum and maximum sizes ................................. 2-6
Paper length guide ........... .. ............................... ............ 2-14
Paper stopper ................................................. .............. 2-13
components ............................................................. 1-2
Paper weight ................................................................... 2-7
Paper width guide ............ ............................................. 2-13
Platen
cleaning ................................................................... 8-5
components ............................................................. 1-2
loading originals ............. ... ..................................... 2-18
Postcards ......................... ............................................. 2-10
Power cord
connection ............................................................... 2-3
Power cord connector
components ............................................................. 1-3
Power switch
components ............................................................. 1-2
Preparation ..................................................................... 2-1
Preparing paper ......... ... ................................................ 2-12
Preprinted paper ................... ... ..................................... 2-11
Preset Tool .................... ............................... ................. 2-32
Print Box ......................................................................... 4-6
printing ..................................................................... 4-7
saving ...................................................................... 4-6
Printing ............................................................................ 4-1
manual duplex ......................................................... 4-4
manual feed ............................................................. 4-3
printer driver ............................................................ 4-2
printing from application so ftware ............................ 4-2
Programs
copying .................................................................... 3-5
FAX ........................... ............................................. 7-15
registering ................. .. ................. .......................... 2-32
Index-3
scanning ............................. ..................................... 5-3
Prolonged non-use .................... ................ ..................... 8-9
Push Scan .......... ............................... ............................. 5-2
Q
Quick Scan
settings .................................................................. 2-45
using ......... ............................................. .................. 5- 4
Quiet Mode .................................. ................................... 1-4
Quiet Mode key
operation panel ............. ... ........................................ 1-4
R
Rear cover
components ............ ............................................. .... 1- 3
Rear cover section
clearing paper jams ............................................... 9-15
Recycled paper ............................................................. 2-11
Replacement
maintenance kit ............... ... ..................................... 8-5
toner container ..................... ... ................................ 8- 2
S
Scanning ......... ... ............................... ............................. 5-1
programs ...................... ........................................... 5-3
Push Scan ................. ................. ............................. 5-2
Quick Scan .......................................................... .... 5- 4
TWAIN/WIA ............... ................. ............................. 5-5
Slit glass
components ............ ............................................. .... 1- 2
Slit glass cover
cleaning ..................... ............................... ............... 8-6
Software ....................................................................... 2-20
Solving malfunctions .................................... .................. 9-2
Special paper ..................................... ............................. 2-9
Specifications ............................................................... 10-5
common functi ons ................................................. 10-5
copy ....................................................................... 10-6
document processor ............................................ 10-11
FAX ..................................................................... 10-10
printer .................................................................... 10-8
scanner ............................................................... 10-10
Status Monitor ............................................................... 2-31
Status page
printing .................................................................. 2-58
System menu ........... .. ............................... ..................... 6-2
adjustment and maintenance ........................ 6-5, 7-27
common settings ........................................... 6-4, 7-25
FAX settings .......................................................... 7-26
operation meth od ....................... ... .......................... 6-2
report ............................................................. 6-3, 7-25
T
Thick paper ................................................................... 2-11
Tips ............... ............................... ................................... 9-7
Toner container
how to replace ......................... ................................ 8-3
replacement ............................................................. 8-2
Toner kit
toner container, plastic waste bag, installation guide 8-2
Troubleshooting .............................................................. 9-1
clearing paper jams ..................... .......................... 9-14
error messages ........................................................ 9-8
FAX error code list .................... ... .......................... 9-12
solving malfunctions ................................................ 9-2
Turning on the power ...................................................... 2-4
TWAIN/WIA .................................................................... 5-5
U
Uninstalling drivers and utilities .................................... 2-25
Unusabl e ti me ...................................................... ......... 7-35
USB cable
connection ............................................................... 2-2
USB interface connector
components ............................................................. 1-3
Z
Zoom ............................................................................... 3-7
Index-4
KYOCERA Document Solutions Austria GmbH
Eduard-Kittenberger-Gasse 95, 1230 Vienna,
Austria
Phone: +43-1-863380
Fax: +43-1-86338-400
KYOCERA Document Solutions Nordic AB
Esbogatan 16B 164 75 Kista,
Sweden
Phone: +46-8-546-550-00
Fax: +46-8-546-550-10
KYOCERA Document Solutions Norge NUF
Postboks 150 Oppsal, 0619 Oslo,
Norway
Phone: +47-22-62-73-00
Fax: +47-22-62-72-00
KYOCERA Document Solutions Danmark A/S
Ejby Industrivej 60, DK-2600 Glostrup,
Denmark
Phone: +45-70223880
Fax: +45-45765850
KYOCERA Document Solutions Portugal Lda.
Rua do Centro Cultural, 41 (Alvalade) 1700-106 Lisboa,
Portugal
Phone: +351-21-843-6780
Fax: +351-21-849-3312
KYOCERA Document Solutions
South Africa (Pty) Ltd.
49 Kyalami Boulevard,
Kyalami Business Park 1685 Midrand, South Africa
Phone: +27-11-540-2600
Fax: +27-11-466-3050
KYOCERA Document Solutions Russia LLC
Botanichesky pereulok 5, Moscow, 129090,
Russia
Phone: +7(495)741-0004
Fax: +7(495)741-0018
KYOCERA Document Solutions Middle East
Dubai Internet City, Bldg. 17,
Office 157 P.O. Box 500817, Dubai,
United Arab Emirates
Phone: +971-04-433-0412
KYOCERA Document Solutions Inc.
2-28, 1-chome, Tamatsukuri, Chuo-ku
Osaka 540-8585, Japan
Phone: +81-6-6764-3555
http://www.kyoceradocumentsolutions.com
KYOCERA Document Solutions Europe B.V.
Bloemlaan 4, 2132 NP Hoofddorp,
The Netherlands
Phone: +31-20-654-0000
Fax: +31-20-653-1256
KYOCERA Document Solutions Nederland B.V.
Beechavenue 25, 1119 RA Schiphol-Rijk,
The Netherlands
Phone: +31-20-5877200
Fax: +31-20-5877260
KYOCERA Document Solutions (U.K.) Limited
8 Beacontree Plaza,
Gillette Way Reading, Berkshire RG2 0BS,
United Kingdom
Phone: +44-118-931-1500
Fax: +44-118-931-1108
KYOCERA Document Solutions Italia S.p.A.
Via Verdi, 89/91 20063 Cernusco s/N.(MI),
Italy
Phone: +39-02-921791
Fax: +39-02-92179-600
KYOCERA Document Solutions Belgium N.V.
Sint-Martinusweg 199-201 1930 Zaventem,
Belgium
Phone: +32-2-7209270
Fax: +32-2-7208748
KYOCERA Document Solutions France S.A.S.
Espace Technologique de St Aubin
Route de I’Orme 91195 Gif-sur-Yvette CEDEX,
France
Phone: +33-1-69852600
Fax: +33-1-69853409
KYOCERA Document Solutions Espana, S.A.
Edificio Kyocera, Avda. de Manacor No.2,
28290 Las Matas (Madrid), Spain
Phone: +34-91-6318392
Fax: +34-91-6318219
KYOCERA Document Solutions Finland Oy
Atomitie 5C, 00370 Helsinki,
Finland
Phone: +358-9-47805200
Fax: +358-9-47805390
KYOCERA Document Solutions
Europe B.V., Amsterdam (NL) Zürich Branch
Hohlstrasse 614, 8048 Zürich,
Switzerland
Phone: +41-44-9084949
Fax: +41-44-9084950
KYOCERA Document Solutions
Deutschland GmbH
Otto-Hahn-Strasse 12, 40670 Meerbusch,
Germany
Phone: +49-2159-9180
Fax: +49-2159-918100
First Edition 2012.09
2M7KMEN000