Lenovo M920 User Manual

Displayed below is the user manual for M920 by Lenovo which is a product in the PCs/Workstations category. This manual has pages.

Related Manuals

Lenovo M920 Manual

M920s User Guide and Hardware

Maintenance Manual

Energy Star Machine Types: 10SJ, 10SK, 10SL, 10TN, 10U2 and

10U3

Note: Before using this information and the product it supports, be sure to read and understand the

Important Product Information Guide and Appendix A “Notices” on page 65.

Second Edition (August 2019)

LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered pursuant to a General Services

Administration “GSA” contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS-

35F-05925.

Contents

Chapter 1. Overview. . . . . . . . . . . 1

Front view . . . . . . . . . . . . . . . . . . 1

Rear view . . . . . . . . . . . . . . . . . . 3

System board . . . . . . . . . . . . . . . . 5

Machine type and model label . . . . . . . . . . 6

Chapter 2. Specifications . . . . . . . . 7

Chapter 3. Computer locks . . . . . . . 9

Enabling or disabling the E-lock . . . . . . . . . 9

Locking the computer cover . . . . . . . . . . 10

Attaching a Kensington-style cable lock . . . . . 10

Attaching a cable lock . . . . . . . . . . . . 11

Chapter 4. Replacing hardware . . . . 13

Before replacing hardware . . . . . . . . . . 13

Knowing FRUs (including CRUs) . . . . . . . . 13

Locating FRUs (including CRUs) . . . . . . . . 14

Replacing the power cord . . . . . . . . . . . 16

Replacing the external options . . . . . . . . . 17

Removing the computer cover . . . . . . . . . 19

Replacing the front bezel . . . . . . . . . . . 20

Replacing the optical drive . . . . . . . . . . 21

Pivoting the drive bay assembly upward and

downward . . . . . . . . . . . . . . . . . 23

Replacing the internal speaker . . . . . . . . . 24

Replacing the illuminated red dot . . . . . . . . 27

Replacing the thermal sensor . . . . . . . . . 28

Replacing the front I/O options . . . . . . . . . 31

Replacing the storage drive . . . . . . . . . . 34

Replacing the memory module . . . . . . . . . 40

Replacing the heat sink and fan assembly . . . . 41

Replacing the microprocessor . . . . . . . . . 43

Replacing a PCI Express card . . . . . . . . . 45

Replacing the E-lock . . . . . . . . . . . . . 46

Replacing the cover presence switch . . . . . . 47

Replacing the Wi-Fi card . . . . . . . . . . . 48

Replacing the Wi-Fi antennas . . . . . . . . . 52

Replacing the coin-cell battery . . . . . . . . . 54

Replacing the M.2 storage drive . . . . . . . . 56

Replacing the M.2 storage drive bracket . . . . . 58

Replacing the power supply assembly . . . . . . 59

Replacing the system board . . . . . . . . . . 61

Completing the parts replacement . . . . . . . 62

Appendix A. Notices. . . . . . . . . . 65

Appendix B. Trademarks . . . . . . . 67

ii M920s User Guide and Hardware Maintenance Manual

Chapter 1. Overview

This chapter provides basic information to help you get familiar with your computer.

Front view

Note: Your computer model might look slightly different from the illustration.

Figure 1. Front view

1 Optical drive eject/close button (optional) 2 Optical drive status indicator (optional)

3 Storage drive activity indicator 4 Card reader (optional)

5 USB-C™ connector (only supports USB data

transmission)

6 Power button

7 Power indicator 8 Microphone connector

9 Headset connector 10 USB 3.1 Gen 1 connectors (2)

11 USB 3.1 Gen 2 connectors (2) 12 Illuminated red dot

13 Internal speaker

1 Optical drive eject/close button

Used to eject the tray of the optical drive. After you insert a disc into the tray, press the eject/close button to

close the tray.

2 Optical drive activity indicator

This indicator is on when the optical drive is in use.

3 Storage drive activity indicator

This indicator is on when the storage drive is in use.

4 Card reader slot

Used to read data from a supported memory card.

5 USB-C connector (only supports USB data transmission)

Use the connector to transfer data (USB 3.1 Gen 1, 5.0Gbps), charge your device (5V/3A), or connect to

USB-C accessories to help expand your computer functionality. To purchase USB-C accessories, go to:

https://www.lenovo.com/accessories

6 Power button

Used to turn on your computer. When you cannot shut down the computer from the operating system, press

and hold the power button for four or more seconds to turn off the computer.

7 Power indicator

This indicator is on when the computer is on.

8 Microphone connector

Used to connect a microphone to your computer. You can use the microphone to record sounds or interact

with the computer using speech-recognition software.

9 Headset connector

Used to connect headset to your computer.

10 USB 3.1 Gen 1 connectors

Used to connect a USB-compatible device. For optimal data transfer, connect a USB 3.1 Gen 1 device to a

USB 3.1 Gen 2 or USB 3.1 Gen 1 connector instead of a USB 2.0 connector.

11 USB 3.1 Gen 2 connectors

Used to connect a USB-compatible device. For optimal data transfer, connect a USB 3.1 Gen 2 device to a

USB 3.1 Gen 2 connector instead of a USB 3.1 Gen 1 or USB 2.0 connector.

12 Illuminated red dot

This indicator is on when the computer is on.

13 Internal speaker

Used to listen to the sounds from your computer without using a headset or headphones.

2M920s User Guide and Hardware Maintenance Manual

Rear view

Note: Your computer model might look slightly different from the illustration.

Figure 2. Rear view

1 Audio line-out connector 2 VGA-out connector

3 DisplayPort® 1.2 out connector(2) 4 USB 3.1 Gen 1 connector

5 USB 3.1 Gen 1 connectors (3) 6 Serial connector

7 PS/2 mouse connector (optional) 8 PS/2 keyboard connector (optional)

9 Ethernet connector 10 Security-lock slot

11 Padlock loop 12 PCI-Express card area (different cards provide different

connectors)

13 Power cord connector

1 Audio line-out connector

Used to send audio signals from the computer to external devices, such as powered stereo speakers,

headphones, or multimedia keyboards. To connect a stereo system or other external recording device,

connect a cable between the audio line-in connector of the device and the audio line-out connector of the

computer.

Chapter 1.Overview 3

Note: If your computer has both an audio line-out connector and a headset or headphone connector, always

use the headset connector or headphone connector for earphones, headphones, or a headset. The

headphone connector does not support headset microphones.

2 VGA-out connector

Used to send video signals from the computer to another video device, such as a monitor.

3 DisplayPort 1.2 out connector

Used to send audio and video signals from the computer to another audio or video device, such as a high-

performance monitor.

4 USB 3.1 Gen 1 connector

Used to connect a USB-compatible device. For optimal data transfer, connect a USB 3.1 Gen 1 device to a

USB 3.1 Gen 2 or USB 3.1 Gen 1 connector instead of a USB 2.0 connector. This connector supports the

smart power on feature that enables you to turn on the computer or wake it up from S4 hibernation mode by

pressing Alt+P on the keyboard. You can enable or disable the smart power on feature from the Setup Utility

program. For detailed information, see the Important Product Information Guide.

5 USB 3.1 Gen 1 connectors

Used to connect a USB-compatible device. For optimal data transfer, connect a USB 3.1 Gen 1 device to a

USB 3.1 Gen 2 or USB 3.1 Gen 1 connector instead of a USB 2.0 connector.

6 Serial connector

Used to connect an external modem, a serial printer, or other devices that use a serial connector.

7 PS/2 mouse connector

Used to connect a mouse, a trackball, or other pointing devices that use a PS/2 mouse connector.

8 PS/2 keyboard connector

Used to connect a keyboard that uses a Personal System/2 (PS/2) keyboard connector.

9 Ethernet connector

Used to connect an Ethernet cable for network access.

10 Security-lock slot

Used to secure a Kensington-style cable lock.

11 Padlock loop

Used to secure a padlock.

12 PCI-Express card area

To improve the operating performance of the computer, you can connect PCI-Express cards into this area.

Depending on the computer model, the connectors in this area vary.

13 Power cord connector

4M920s User Guide and Hardware Maintenance Manual

Used to connect the power cord to your computer for power supply.

System board

Note: See “Front view” on page 1 and “Rear view” on page 3 for additional component descriptions.

Figure 3. System board

1 4-pin power connector 2 Microprocessor fan connector

3 Memory slot (DIMM1) 4 Memory slot (DIMM2)

5 Memory slot (DIMM3) 6 Memory slot (DIMM4)

7 Power button board connector 8 Internal speaker connector

9 10-pin power connector 10 SATA power connector

11 SATA power connector 12 Auxiliary fan connector

13 SATA 3.0 connector 14 SATA 3.0 connector

15 SATA 3.0 connector 16 Clear CMOS jumper

17 SATA 3.0 connector 18 M.2 storage drive slot

19 M.2 Wi-Fi card slot 20 Thermal sensor connector

21 Illuminated red dot connector 22 Front USB 2.0 connector

23 Front USB 2.0 connector 24 Serial connector (optional)

25 Thunderbolt connector 26 PCI Express card slot (physical link width x16;

negotiable link width x4, x1)

27 PCI Express x1 card slot 28 PCI Express x16 graphics card slot

Chapter 1.Overview 5

29 E-lock connector 30 System fan connector

31 Cover presence switch 32 Coin-cell battery

33 Microprocessor socket 34 PS/2 keyboard and mouse connector

Machine type and model label

The machine type and model label identifies the computer. When you contact Lenovo for help, the machine

type and model information helps support technicians to identify the computer and provide faster service.

The machine type and model label is attached on the side of the computer as shown.

Figure 4. Machine type and model label

6M920s User Guide and Hardware Maintenance Manual

Chapter 2. Specifications

Power supply

• 180 watt automatic voltage-sensing power supply

• 210 watt automatic voltage-sensing power supply

• 260 watt automatic voltage-sensing power supply

Storage drives

Up to two SATA storage drives and one M.2 storage drive

Video features

• The integrated graphics card supports the following:

– DisplayPort-out connector

– VGA-out connector

• The optional discrete graphics card provides an enhanced video experience and extended capabilities.

Audio features

• The integrated audio card supports the following:

– Audio line-out connector

– Headset connector

– Internal speaker

– Microphone connector

• The optional discrete audio card provides an enhanced audio experience and extended capabilities.

Input/Output (I/O) features

• Audio connectors (audio line-out connector, headset connector, and microphone connector)

• Card reader slot (optional)

• Display connectors (DisplayPort-out connector and VGA-out connector)

• Ethernet connector

• PS/2 keyboard connector (optional)

• PS/2 mouse connector (optional)

• Serial connector

• USB connectors

Expansion

• Card reader (optional)

• Memory slot

• Optical drive (optional)

• PCI Express card slot (physical link width x16; negotiable link width x4, x1)

• PCI Express x1 card slot

• PCI Express x16 graphics card slot

• Storage drive bay

Network features

• Ethernet LAN

• Wireless LAN (optional)

• Bluetooth (optional)

Physical dimensions

• Width: 92.5 mm (3.6 inches)

• Height: 343.5 mm (13.5 inches)

• Depth: 290.5 mm (11.4 inches)

Weight (without the package)

Maximum configuration as shipped: 6.0 kg (13.2 lb)

Statement on USB transfer rate

Depending on many factors such as the processing capability of the host and peripheral devices, file

attributes, and other factors related to system configuration and operating environments, the actual transfer

rate using the various USB connectors on this device will vary and will be slower than the data rate listed

below for each corresponding device.

USB device Data rate (Gbit/s)

3.1 Gen 1 5

3.1 Gen 2 10

3.2 20

8M920s User Guide and Hardware Maintenance Manual

Chapter 3. Computer locks

This chapter provides instructions on how to lock your computer with the locking devices to keep your

computer safe.

Enabling or disabling the E-lock

Your computer may have a security lock solution installed to protect the computer from unauthorized

tampering of the internal components. Using the E-Lock, you can mechanically lock or unlock the computer

cover.

To enable or disable the E-Lock, do the following:

1. Turn on or restart the computer.

2. Before Windows starts up, repeatedly press and release the F1 or Fn+F1 key until the Setup Utility

program opens.

3. Click Security ➙ Electronic Lock to enable or disable the E-lock.

4. Press F10 or Fn+F10 to save the changes and reboot the computer.

Note: Changes do not take effect until the setting is saved and the system is rebooted.

Figure 5. Enabling or disabling the E-lock

Locking the computer cover

Locking the computer cover helps prevent unauthorized access to the inside of your computer. Your

computer features a padlock loop so that the computer cover cannot be removed when a padlock is

installed.

Figure 6. Locking the computer cover

Attaching a Kensington-style cable lock

You can use a Kensington-style cable lock to secure your computer to a desk, table, or other nonpermanent

fixture. The cable lock connects to the security-lock slot at the rear of your computer. Depending on the type

selected, the cable lock can be operated with a key or combination. The cable lock also locks the buttons

used to open the computer cover. This is the same type of lock used with many notebook computers. You

can order such a cable lock directly from Lenovo by searching for Kensington at:

http://www.lenovo.com/support

Figure 7. Attaching a Kensington-style cable lock

10 M920s User Guide and Hardware Maintenance Manual

Attaching a cable lock

A cable lock can be used to secure devices, such as the keyboard and the mouse, by locking the device

cables to the computer. The cable lock connects to the cable-lock slots on the rear of the computer. To

install a cable lock, do the following:

1. Insert the clip 1 into the cable-lock slot 4.

2. Pull the cables you want to lock through the dents in the cable lock.

3. Press the clip 2 into the cable-lock slot 3 until it snaps into position.

Figure 8. Attaching a cable lock

Chapter 3.Computer locks 11

12 M920s User Guide and Hardware Maintenance Manual

Chapter 4. Replacing hardware

This chapter provides instructions on how to replace hardware for your computer.

Before replacing hardware

Attention: Do not open your computer or attempt any repairs before reading this section and the Important

Product Information Guide.

Notes before replacing hardware

• Use computer components provided only by Lenovo.

• When installing or replacing an option, use the appropriate instructions explained in this manual along with

the instructions that come with the option.

• In most areas of the world, Lenovo requires the return of defective CRUs. Information about this will come

with the CRU or will come a few days after the CRU arrives.

Handling static-sensitive devices

Do not open the static-protective package containing the new part until the defective part has been removed

and you are ready to install the new part. Static electricity, although harmless to you, can seriously damage

computer components and options.

When you handle options and other computer components, take these precautions to avoid static-electricity

damage:

• Limit your movement. Movement can cause static electricity to build up around you.

• Always handle options and other computer components carefully. Handle PCI/PCIe cards, memory

modules, system boards, and microprocessors by the edges. Never touch any exposed circuitry.

• Prevent others from touching the options and other computer components.

• Touch the static-protective package containing the part to a metal expansion-slot cover or other

unpainted metal surface on the computer for at least two seconds. This reduces static electricity from the

package and your body before you install or replace a new part.

• When possible, remove the new part from the static-protective package, and install it directly in the

computer without setting the part down. When this is not possible, place the static-protective package on

a smooth, level surface and place the part on the package.

• Do not place the part on the computer cover or other metal surface.

Knowing FRUs (including CRUs)

• Field Replaceable Units (FRUs) are computer parts that a trained technician can upgrade or replace. FRUs

include all CRUs. For detailed FRU information, such as the FRU part numbers and supported computer

models, go to:

http://www.lenovo.com/serviceparts-lookup

• Customer Replaceable Units (CRUs) are computer parts that a user can upgrade or replace.

– Self-service CRUs: You can install self-service CRUs easily. These CRUs might be stand-alone,

latched, or secured by up to two screws. Examples of self-service CRUs include the keyboard, mouse,

any USB device. You are responsible for replacing all self-service CRUs.

– Optional-service CRUs: Handling optional-service CRUs requires some technical skills and simple tools

(such as a screwdriver). These CRUs are isolated parts within the computer. They are usually

concealed by an access panel that is secured by more than two screws. You must remove the screws

and panel to access the specific CRU. Optional-service CRUs can be removed and installed by users

or, during the warranty period, by a Lenovo service technician.

Before replacing FRUs

Before replacing any FRU, read the following:

• Only certified and trained personnel can service the computer.

• Before replacing an FRU, read the entire section about replacing the part.

• Be extremely careful during writing operations such as copying, saving, or formatting.

The sequence of the drives in the computer that you are servicing might have been altered. If you select

an incorrect drive, data or programs might be overwritten.

• Replace an FRU only with another FRU of the correct model.

When you replace an FRU, ensure that the model of the machine and the FRU part number are correct.

• An FRU should not be replaced because of a single, unreproducible failure.

Single failures can occur for a variety of reasons that have nothing to do with a hardware defect, such as

cosmic radiation, electrostatic discharge, or software errors. Consider replacing an FRU only when a

problem recurs. If you suspect that an FRU is defective, clear the error log and run the test again. If the

error does not recur, do not replace the FRU.

• Only replace a defective FRU.

Locating FRUs (including CRUs)

Notes:

• Some of the following components are optional.

• To replace a component that is not in the list below, contact a Lenovo service technician. For a list of

Lenovo Support phone numbers, go to:

http://www.lenovo.com/support/phone

14 M920s User Guide and Hardware Maintenance Manual

Figure 9. Locating FRUs (including CRUs)

Self-service CRUs Optional-service CRUs Non-CRUs

1 Computer cover 7 Wi-Fi card 2 Heat sink and fan assembly

4 Memory module 8 Wi-Fi card shield 3 Microprocessor

6 Coin-cell battery 34 Power supply assembly 5 System board

10 M.2 storage drive 36 E-lock 9 Cover presence switch

11 M.2 storage drive bracket 14 Power button

12 Secondary storage drive bracket 15 Card reader

13 Secondary storage drive (a 2.5-

inch storage drive)

16 Front I/O bracket

Chapter 4.Replacing hardware 15

Self-service CRUs Optional-service CRUs Non-CRUs

18 Optical drive bracket 17 Optical drive cable

19 Optical drive 28 Storage drive cable

20 Front bezel 29 Illuminated red dot

21 Dust shield 30 Thermal sensor

22 Keyboard 31 Internal speaker

23 Mouse 33 Chassis

24 Power cord 35 Wi-Fi antennas

25 Primary storage drive (a 2.5-inch

or 3.5-inch storage drive)

26 Primary storage drive bracket

27 Storage drive converter

32 Vertical stand

37 PCI Express card

Replacing the power cord

Attention: Do not open your computer or attempt any repairs before reading the Important Product

Information Guide.

1. Remove any media from the drives and turn off all connected devices and the computer. Disconnect all

power cords from electrical outlets and disconnect all cables from the computer.

2. Replace the power cord.

Figure 10. Removing the power cord

16 M920s User Guide and Hardware Maintenance Manual

Figure 11. Installing the power cord

Replacing the external options

Attention: Do not open your computer or attempt any repairs before reading the Important Product

Information Guide.

1. Remove any media from the drives and turn off all connected devices and the computer. Disconnect all

power cords from electrical outlets and disconnect all cables from the computer.

2. Refer to the following to replace external options.

• Vertical stand

Figure 12. Removing the vertical stand

Chapter 4.Replacing hardware 17

Figure 13. Assembling the vertical stand

Figure 14. Installing the vertical stand

• Dust shield

18 M920s User Guide and Hardware Maintenance Manual

Figure 15. Removing the dust shield

Figure 16. Installing the dust shield

3. Reconnect all cables.

Removing the computer cover

Attention: Do not open your computer or attempt any repairs before reading the Important Product

Information Guide.

CAUTION:

Before you open the computer cover, turn off the computer and wait several minutes until the

computer is cool.

1. Remove any media from the drives and turn off all connected devices and the computer. Disconnect all

power cords from electrical outlets and disconnect all cables from the computer.

Chapter 4.Replacing hardware 19

2. Unlock any locking device that secures the computer cover.

3. Remove the computer cover.

Figure 17. Removing the computer cover

4. Complete the replacement. See “Completing the parts replacement” on page 62.

Replacing the front bezel

Attention: Do not open your computer or attempt any repairs before reading the Important Product

Information Guide.

1. Remove any media from the drives and turn off all connected devices and the computer. Disconnect all

power cords from electrical outlets and disconnect all cables from the computer.

2. Remove the computer cover. See “Removing the computer cover” on page 19.

3. Replace the front bezel.

20 M920s User Guide and Hardware Maintenance Manual

Figure 18. Removing the front bezel

Figure 19. Installing the front bezel

4. Complete the replacement. See “Completing the parts replacement” on page 62.

Replacing the optical drive

Attention: Do not open your computer or attempt any repairs before reading the Important Product

Information Guide.

Chapter 4.Replacing hardware 21

1. Remove any media from the drives and turn off all connected devices and the computer. Disconnect all

power cords from electrical outlets and disconnect all cables from the computer.

2. Remove the computer cover. See “Removing the computer cover” on page 19.

3. Remove the front bezel. See “Replacing the front bezel” on page 20.

4. Disconnect the signal cable and the power cable from the optical drive.

5. Replace the optical drive.

Figure 20. Removing the optical drive

Figure 21. Removing the optical drive retainer

22 M920s User Guide and Hardware Maintenance Manual

Figure 22. Installing the optical drive retainer

Figure 23. Installing the optical drive

6. Connect the signal cable and the power cable to the new optical drive.

7. Reinstall the removed parts. To complete the replacement, see “Completing the parts replacement” on

page 62.

Pivoting the drive bay assembly upward and downward

Attention: Do not open your computer or attempt any repairs before reading the Important Product

Information Guide.

1. Remove any media from the drives and turn off all connected devices and the computer. Disconnect all

power cords from electrical outlets and disconnect all cables from the computer.

2. Remove the computer cover. See “Removing the computer cover” on page 19.

3. Remove the front bezel. See “Replacing the front bezel” on page 20.

4. Pivot the drive bay assembly upward and downward.

Chapter 4.Replacing hardware 23

Figure 24. Pivoting the drive bay assembly upward

Figure 25. Pivoting the drive bay assembly downward

5. Reinstall the removed parts. To complete the replacement, see “Completing the parts replacement” on

page 62.

Replacing the internal speaker

Attention: Do not open your computer or attempt any repairs before reading the Important Product

Information Guide.

1. Remove any media from the drives and turn off all connected devices and the computer. Disconnect all

power cords from electrical outlets and disconnect all cables from the computer.

24 M920s User Guide and Hardware Maintenance Manual

2. Remove the computer cover. See “Removing the computer cover” on page 19.

3. Remove the front bezel. See “Replacing the front bezel” on page 20.

4. Disconnect the internal speaker cable from the system board.

5. Replace the internal speaker.

Figure 26. Removing the internal speaker screws

Figure 27. Pivoting the drive bay assembly upward

Chapter 4.Replacing hardware 25

Figure 28. Removing the internal speaker

Figure 29. Installing the internal speaker

Figure 30. Installing the internal speaker screws

26 M920s User Guide and Hardware Maintenance Manual

Figure 31. Pivoting the drive bay assembly downward

6. Connect the new internal speaker cable to the system board.

7. Reinstall the removed parts. To complete the replacement, see “Completing the parts replacement” on

page 62.

Replacing the illuminated red dot

Attention: Do not open your computer or attempt any repairs before reading the Important Product

Information Guide.

1. Remove any media from the drives and turn off all connected devices and the computer. Disconnect all

power cords from electrical outlets and disconnect all cables from the computer.

2. Remove the computer cover. See “Removing the computer cover” on page 19.

3. Remove the front bezel. See “Replacing the front bezel” on page 20.

4. Pivot the drive bay assembly upward. See “Pivoting the drive bay assembly upward and downward” on

page 23.

5. Disconnect the illuminated red dot cable from the system board.

6. Replace the illuminated red dot.

Figure 32. Removing the illuminated red dot cover

Chapter 4.Replacing hardware 27

Figure 33. Removing the illuminated red dot

Figure 34. Installing the illuminated red dot

Figure 35. Installing the illuminated red dot cover

7. Connect the new illuminated red dot cable to the system board.

8. Reinstall the removed parts. To complete the replacement, see “Completing the parts replacement” on

page 62.

Replacing the thermal sensor

Attention: Do not open your computer or attempt any repairs before reading the Important Product

Information Guide.

1. Remove any media from the drives and turn off all connected devices and the computer. Disconnect all

power cords from electrical outlets and disconnect all cables from the computer.

2. Remove the computer cover. See “Removing the computer cover” on page 19.

28 M920s User Guide and Hardware Maintenance Manual

3. Remove the front bezel. See “Replacing the front bezel” on page 20.

4. Disconnect the thermal sensor cable from the system board.

5. Replace the thermal sensor.

Figure 36. Pressing the tab

Figure 37. Pivoting the drive bay assembly upward

Chapter 4.Replacing hardware 29

Figure 38. Removing the thermal sensor

Figure 39. Installing the thermal sensor

Figure 40. Pivoting the drive bay assembly downward

6. Connect the new thermal sensor cable to the system board.

30 M920s User Guide and Hardware Maintenance Manual

7. Reinstall the removed parts. To complete the replacement, see “Completing the parts replacement” on

page 62.

Replacing the front I/O options

Attention: Do not open your computer or attempt any repairs before reading the Important Product

Information Guide.

1. Remove any media from the drives and turn off all connected devices and the computer. Disconnect all

power cords from electrical outlets and disconnect all cables from the computer.

2. Remove the computer cover. See “Removing the computer cover” on page 19.

3. Remove the front bezel. See “Replacing the front bezel” on page 20.

4. Disconnect the power button board cable and card reader cable from the system board.

5. Replace the front I/O options.

Figure 41. Removing the front I/O bracket

Figure 42. Removing the power button board

Chapter 4.Replacing hardware 31

Figure 43. Removing the card reader bracket

Figure 44. Removing the card reader

32 M920s User Guide and Hardware Maintenance Manual

Figure 45. Installing the card reader

Figure 46. Installing the card reader bracket

Chapter 4.Replacing hardware 33

Figure 47. Installing the power button board

Figure 48. Installing the front I/O bracket

6. Connect the new front I/O options cable to the system board.

7. Reinstall the removed parts. To complete the replacement, see “Completing the parts replacement” on

page 62.

Replacing the storage drive

Attention: Do not open your computer or attempt any repairs before reading the Important Product

Information Guide.

Replacing the 3.5-inch primary storage drive

1. Remove any media from the drives and turn off all connected devices and the computer. Disconnect all

power cords from electrical outlets and disconnect all cables from the computer.

34 M920s User Guide and Hardware Maintenance Manual

2. Remove the computer cover. See “Removing the computer cover” on page 19.

3. Remove the front bezel. See “Replacing the front bezel” on page 20.

4. Pivot the drive bay assembly outward. See “Pivoting the drive bay assembly upward and downward” on

page 23.

5. Disconnect the signal cable and the power cable from the 3.5-inch primary storage drive.

6. Replace the 3.5-inch primary storage drive.

Figure 49. Removing the storage drive bracket

Figure 50. Removing the storage drive

Chapter 4.Replacing hardware 35

Figure 51. Installing the storage drive

Figure 52. Installing the storage drive bracket

7. Connect the signal cable and the power cable to the new 3.5-inch storage drive.

8. Reinstall the removed parts. To complete the replacement, see “Completing the parts replacement” on

page 62.

Replacing the 2.5-inch primary storage drive

1. Remove the storage converter with the 2.5-inch primary sstorage drive. See "Replacing the 3.5-inch

primary storage drive".

2. Replace the 2.5-inch primary storage drive in the storage converter.

36 M920s User Guide and Hardware Maintenance Manual

Figure 53. Removing the storage drive

Figure 54. Installing the storage drive

3. Reinstall the storage converter with the 2.5-inch primary storage drive. See "Replacing the 3.5-inch

primary storage drive".

Replacing the 2.5-inch secondary storage drive

1. Remove any media from the drives and turn off all connected devices and the computer. Disconnect all

power cords from electrical outlets and disconnect all cables from the computer.

2. Remove the computer cover. See “Removing the computer cover” on page 19.

3. Remove the front bezel. See “Replacing the front bezel” on page 20.

Chapter 4.Replacing hardware 37

4. Pivot the drive bay assembly outward. See “Pivoting the drive bay assembly upward and downward” on

page 23.

5. Disconnect the signal cable and the power cable from the 2.5-inch secondary storage drive.

6. Replace the 2.5-inch secondary storage drive.

Figure 55. Removing the outer storage drive bracket

Figure 56. Removing the inner storage drive bracket

38 M920s User Guide and Hardware Maintenance Manual

Figure 57. Removing the storage drive

Figure 58. Installing the storage drive

Figure 59. Installing the inner storage drive bracket

Chapter 4.Replacing hardware 39

Figure 60. Installing the outer storage drive bracket

7. Connect the signal cable and the power cable to the new 2.5-inch secondary storage drive.

8. Reinstall the removed parts. To complete the replacement, see “Completing the parts replacement” on

page 62.

Replacing the memory module

Attention: Do not open your computer or attempt any repairs before reading the Important Product

Information Guide.

Ensure that you follow the order of installing memory modules shown in the following figure.

Figure 61. The order of installing memory modules

40 M920s User Guide and Hardware Maintenance Manual

1. Remove any media from the drives and turn off all connected devices and the computer. Disconnect all

power cords from electrical outlets and disconnect all cables from the computer.

2. Remove the computer cover. See “Removing the computer cover” on page 19.

3. Remove the front bezel. See “Replacing the front bezel” on page 20.

4. Pivot the drive bay assembly upward. See “Pivoting the drive bay assembly upward and downward” on

page 23.

5. Replace the memory module.

Figure 62. Removing the memory module

Figure 63. Installing the memory module

6. Reinstall the removed parts. To complete the replacement, see “Completing the parts replacement” on

page 62.

Replacing the heat sink and fan assembly

Attention: Do not open your computer or attempt any repairs before reading the Important Product

Information Guide.

CAUTION:

The heat sink and fan assembly might be very hot. Before you open the computer cover, turn off the

computer and wait several minutes until the computer is cool.

Chapter 4.Replacing hardware 41

1. Remove any media from the drives and turn off all connected devices and the computer. Disconnect all

power cords from electrical outlets and disconnect all cables from the computer.

2. Remove the computer cover. See “Removing the computer cover” on page 19.

3. Remove the front bezel. See “Replacing the front bezel” on page 20.

4. Pivot the drive bay assembly upward. See “Pivoting the drive bay assembly upward and downward” on

page 23.

5. Disconnect the heat sink and fan assembly cable from the system board.

6. Replace the heat sink and fan assembly.

Figure 64. Removing the heat sink and fan assembly

Figure 65. Installing the heat sink and fan assembly

7. Connect the new heat sink and fan assembly cable to the system board.

42 M920s User Guide and Hardware Maintenance Manual

8. Reinstall the removed parts. To complete the replacement, see “Completing the parts replacement” on

page 62.

Replacing the microprocessor

Attention: Do not open your computer or attempt any repairs before reading the Important Product

Information Guide.

CAUTION:

The heat sink and microprocessor might be very hot. Before you open the computer cover, turn off the

computer and wait several minutes until the computer is cool.

1. Remove the computer cover. See “Removing the computer cover” on page 19.

2. Remove the front bezel. See “Replacing the front bezel” on page 20.

3. Pivot the drive bay assembly upward. See “Pivoting the drive bay assembly upward and downward” on

page 23.

4. Remove the heat sink and fan assembly. See “Replacing the heat sink and fan assembly” on page 41.

5. Disconnect all cables connected to the system board.

6. Replace the microprocessor.

Notes:

• Your microprocessor and socket might look different from the one illustrated.

• Touch only the edges of the microprocessor. Do not touch the gold contacts on the bottom.

• Do not drop anything onto the microprocessor socket while it is exposed. The socket pins must be

kept as clean as possible.

Figure 66. Releasing the holder

Figure 67. Pivoting up the socket

Chapter 4.Replacing hardware 43

Figure 68. Removing the microprocessor

Figure 69. Installing the microprocessor

Figure 70. Pivoting the socket downward

44 M920s User Guide and Hardware Maintenance Manual

Figure 71. Securing the holder

7. Reconnect all cables that were disconnected from the system board.

8. Reinstall the removed parts. To complete the replacement, see “Completing the parts replacement” on

page 62.

Replacing a PCI Express card

Attention: Do not open your computer or attempt any repairs before reading the Important Product

Information Guide.

1. Remove any media from the drives and turn off all connected devices and the computer. Disconnect all

power cords from electrical outlets and disconnect all cables from the computer.

2. Remove the computer cover. See “Removing the computer cover” on page 19.

3. Remove the front bezel. See “Replacing the front bezel” on page 20.

4. Pivot the drive bay assembly upward. See “Pivoting the drive bay assembly upward and downward” on

page 23.

5. Replace a PCI Express card.

Figure 72. Removing a PCI Express card

Note: If the card is held in place by a retaining latch, press the latch 1 as shown to disengage the latch.

Then, gently remove the card from the slot.

Chapter 4.Replacing hardware 45

Figure 73. Installing a PCI Express card

6. Reinstall the removed parts. To complete the replacement, see “Completing the parts replacement” on

page 62.

Replacing the E-lock

Attention: Do not open your computer or attempt any repairs before reading the Important Product

Information Guide.

Note: To remove the screws, you need a special tool (T15 star wrench).

1. Remove any media from the drives and turn off all connected devices and the computer. Disconnect all

power cords from electrical outlets and disconnect all cables from the computer.

2. Remove the computer cover. See “Removing the computer cover” on page 19.

3. Disconnect the E-lock cable from the system board.

4. Replace the E-lock.

46 M920s User Guide and Hardware Maintenance Manual

Figure 74. Removing the E-lock

Figure 75. Installing the E-lock

5. Reinstall the removed parts. To complete the replacement, see “Completing the parts replacement” on

page 62.

Replacing the cover presence switch

Attention: Do not open your computer or attempt any repairs before reading the Important Product

Information Guide.

1. Remove any media from the drives and turn off all connected devices and the computer. Disconnect all

power cords from electrical outlets and disconnect all cables from the computer.

2. Remove the computer cover. See “Removing the computer cover” on page 19.

3. Disconnect the cover presence switch cable from the system board.

4. Replace the cover presence switch.

Chapter 4.Replacing hardware 47

Figure 76. Removing the cover presence switch

Figure 77. Installing the cover presence switch

5. Connect the new cover presence switch cable to the system board.

6. Reinstall the removed parts. To complete the replacement, see “Completing the parts replacement” on

page 62.

Replacing the Wi-Fi card

Attention: Do not open your computer or attempt any repairs before reading the Important Product

Information Guide.

1. Remove any media from the drives and turn off all connected devices and the computer. Disconnect all

power cords from electrical outlets and disconnect all cables from the computer.

2. Remove the computer cover. See “Removing the computer cover” on page 19.

3. Remove the front bezel. See “Replacing the front bezel” on page 20.

4. Pivot the drive bay assembly upward. See “Pivoting the drive bay assembly upward and downward” on

page 23.

5. Replace the Wi-Fi card.

48 M920s User Guide and Hardware Maintenance Manual

• Type 1

Figure 78. Removing the Wi-Fi card shield

Figure 79. Disconnecting the antennas

Figure 80. Removing the Wi-Fi card

Chapter 4.Replacing hardware 49

Figure 81. Installing the Wi-Fi card

Figure 82. Connecting the antennas

Figure 83. Installing the Wi-Fi card shield

• Type 2

50 M920s User Guide and Hardware Maintenance Manual

Figure 84. Removing the Wi-Fi card shield

Figure 85. Disconnecting the antennas

Figure 86. Removing the Wi-Fi card

Chapter 4.Replacing hardware 51

Figure 87. Installing the Wi-Fi card

Figure 88. Connecting the antennas

Figure 89. Installing the Wi-Fi card shield

6. Reinstall the removed parts. To complete the replacement, see “Completing the parts replacement” on

page 62.

Replacing the Wi-Fi antennas

Attention: Do not open your computer or attempt any repairs before reading the Important Product

Information Guide.

1. Remove any media from the drives and turn off all connected devices and the computer. Disconnect all

power cords from electrical outlets and disconnect all cables from the computer.

2. Remove the computer cover. See “Removing the computer cover” on page 19.

52 M920s User Guide and Hardware Maintenance Manual

3. Remove the front bezel. See “Replacing the front bezel” on page 20.

4. Pivot the drive bay assembly upward. See “Pivoting the drive bay assembly upward and downward” on

page 23.

5. Disconnect the antenna cables from the Wi-Fi card.

6. Replace the Wi-Fi antennas.

• Front Wi-Fi antenna

Figure 90. Removing the Wi-Fi antenna

Figure 91. Installing the Wi-Fi antenna

• Rear Wi-Fi antenna

Chapter 4.Replacing hardware 53

Figure 92. Removing the Wi-Fi antenna

Figure 93. Installing the Wi-Fi antenna

7. Reinstall the removed parts. To complete the replacement, see “Completing the parts replacement” on

page 62.

Replacing the coin-cell battery

Attention: Do not open your computer or attempt any repairs before reading the Important Product

Information Guide.

Your computer has a special type of memory that maintains the date, time, and settings for built-in features,

such as parallel connector assignments (configurations). A coin-cell battery keeps this information active

when you turn off the computer.

The coin-cell battery normally requires no charging or maintenance throughout its life; however, no coin-cell

battery lasts forever. If the coin-cell battery fails, the date, time, and configuration information (including

passwords) are lost. An error message is displayed when you turn on the computer.

To replace the coin-cell battery,

1. Remove any media from the drives and turn off all connected devices and the computer. Disconnect all

power cords from electrical outlets and disconnect all cables from the computer.

2. Remove the computer cover. See “Removing the computer cover” on page 19.

54 M920s User Guide and Hardware Maintenance Manual

3. Remove the front bezel. See “Replacing the front bezel” on page 20.

4. Pivot the drive bay assembly upward. See “Pivoting the drive bay assembly upward and downward” on

page 23.

5. Replace the coin-cell battery.

Figure 94. Removing the coin-cell battery

Figure 95. Removing the coin-cell battery

Figure 96. Installing the coin-cell battery

Figure 97. Installing the coin-cell battery

6. Reinstall the removed parts. To complete the replacement, see “Completing the parts replacement” on

page 62.

To dispose of the coin-cell battery, refer to Lithium coin-cell battery notice in the Safety and Warranty Guide.

Chapter 4.Replacing hardware 55

Replacing the M.2 storage drive

Attention: Do not open your computer or attempt any repairs before reading the Important Product

Information Guide.

1. Remove any media from the drives and turn off all connected devices and the computer. Disconnect all

power cords from electrical outlets and disconnect all cables from the computer.

2. Remove the computer cover. See “Removing the computer cover” on page 19.

3. Remove the front bezel. See “Replacing the front bezel” on page 20.

4. Pivot the drive bay assembly upward. See “Pivoting the drive bay assembly upward and downward” on

page 23.

5. Replace the M.2 storage drive.

• Type 1

Figure 98. Pulling out the plastic fastener

Figure 99. Removing the optical drive retainer

56 M920s User Guide and Hardware Maintenance Manual

Figure 100. Installing the optical drive retainer

Figure 101. Installing the optical drive

• Type 2

Figure 102. Pulling out the plastic fastener

Chapter 4.Replacing hardware 57

Figure 103. Removing the optical drive bracket

Figure 104. Installing the optical drive bracket

Figure 105. Installing the optical drive

6. Reinstall the removed parts. To complete the replacement, see “Completing the parts replacement” on

page 62.

Replacing the M.2 storage drive bracket

Attention: Do not open your computer or attempt any repairs before reading the Important Product

Information Guide.

58 M920s User Guide and Hardware Maintenance Manual

1. Remove any media from the drives and turn off all connected devices and the computer. Disconnect all

power cords from electrical outlets and disconnect all cables from the computer.

2. Remove the computer cover. See “Removing the computer cover” on page 19.

3. Remove the front bezel. See “Replacing the front bezel” on page 20.

4. Pivot the drive bay assembly upward. See “Pivoting the drive bay assembly upward and downward” on

page 23.

5. Remove the M.2 storage drive.

6. Replace the M.2 storage drive bracket.

Figure 106. Removing the M.2 storage drive bracket

Figure 107. Installing the M.2 storage drive bracket

7. Reinstall the removed parts. To complete the replacement, see “Completing the parts replacement” on

page 62.

Replacing the power supply assembly

Attention: Do not open your computer or attempt any repairs before reading the Important Product

Information Guide.

Chapter 4.Replacing hardware 59

Although there are no moving parts in your computer after the power cord has been disconnected, the

following warnings are required for your safety and proper Underwriters Laboratories (UL) certification.

CAUTION:

Never remove the cover on a power supply or any part that has the following label attached.

Hazardous voltage, current, and energy levels are present inside any component that has this label

attached. There are no serviceable parts inside these components. If you suspect a problem with one

of these parts, contact a service technician.

1. Remove the computer cover. See “Removing the computer cover” on page 19.

2. Remove the front bezel. See “Replacing the front bezel” on page 20.

3. Remove the optical drive. See “Replacing the optical drive” on page 21.

4. Remove the storage drive bracket. See “Replacing the storage drive” on page 34.

5. Disconnect the power supply assembly cable from the system board.

6. Replace the power supply assembly.

Figure 108. Removing the power supply assembly

60 M920s User Guide and Hardware Maintenance Manual

Figure 109. Installing the power supply assembly

7. Connect the new power supply assembly cable to the system board.

8. Reinstall the removed parts. To complete the replacement, see “Completing the parts replacement” on

page 62.

Replacing the system board

Attention: Do not open your computer or attempt any repairs before reading the Important Product

Information Guide.

1. Remove any media from the drives and turn off all connected devices and the computer. Disconnect all

power cords from electrical outlets and disconnect all cables from the computer.

2. Remove the computer cover. See “Removing the computer cover” on page 19.

3. Remove the front bezel. See “Replacing the front bezel” on page 20.

4. Remove the front I/O options. See “Replacing the front I/O options” on page 31.

5. Pivot the drive bay assembly upward. See “Pivoting the drive bay assembly upward and downward” on

page 23.

6. Remove all memory modules. See “Replacing the memory module” on page 40.

7. Remove the heat sink and fan assembly. See “Replacing the heat sink and fan assembly” on page 41.

8. Remove the microprocessor. See “Replacing the microprocessor” on page 43.

9. Remove all PCI Express cards. See “Replacing a PCI Express card” on page 45.

10. Remove the Wi-Fi card. See “Replacing the Wi-Fi card” on page 48.

11. Remove the M.2 storage drive. See “Replacing the M.2 storage drive” on page 56.

12. Record the cable routing and cable connections, and then disconnect all cables from the system board.

See “System board” on page 5.

Chapter 4.Replacing hardware 61

13. Replace the system board.

Notes:

• The numbers in the following figure show the locations of the screws instead of the removing and

reinstalling order of the screws.

• Handle the system board carefully by its edges.

Figure 110. Removing the system board

14. Route all the cables that you disconnected from the failing system board, and then reconnect the cables

to the new system board. See “System board” on page 5.

15. Reinstall the removed parts. To complete the replacement, see “Completing the parts replacement” on

page 62.

Completing the parts replacement

After completing the installation or replacement for all parts, reinstall the computer cover and reconnect the

cables.

To reinstall the computer cover and reconnect the cables to your computer, do the following:

1. Ensure that all components have been reassembled correctly and that no tools or loose screws are left

inside your computer.

2. Ensure that the cables are routed correctly before reinstalling the computer cover. Keep cables clear of

the hinges and sides of the computer chassis to avoid interference when reinstalling the computer

cover.

62 M920s User Guide and Hardware Maintenance Manual

3. Reinstall the computer cover.

Figure 111. Reinstalling the computer cover

4. Place the computer in an upright position.

5. If a locking device is available, use it to lock the computer.

6. Reconnect the external cables and power cords to the corresponding connectors on the computer.

Chapter 4.Replacing hardware 63

64 M920s User Guide and Hardware Maintenance Manual

Appendix A. Notices

Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult

your local Lenovo representative for information on the products and services currently available in your

area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that

Lenovo product, program, or service may be used. Any functionally equivalent product, program, or service

that does not infringe any Lenovo intellectual property right may be used instead. However, it is the user's

responsibility to evaluate and verify the operation of any other product, program, or service.

Lenovo may have patents or pending patent applications covering subject matter described in this

document. The furnishing of this document does not give you any license to these patents. You can send

license inquiries, in writing, to:

Lenovo (United States), Inc.

1009 Think Place - Building One

Morrisville, NC 27560

U.S.A.

Attention: Lenovo Director of Licensing

LENOVO PROVIDES THIS PUBLICATION "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS

OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT,

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some jurisdictions do not allow

disclaimer of express or implied warranties in certain transactions, therefore, this statement may not apply to

you.

This information could include technical inaccuracies or typographical errors. Changes are periodically made

to the information herein; these changes will be incorporated in new editions of the publication. Lenovo may

make improvements and/or changes in the products and/or the programs described in this publication at any

time without notice.

The products described in this document are not intended for use in implantation or other life support

applications where malfunction may result in injury or death to persons. The information contained in this

document does not affect or change Lenovo product specifications or warranties. Nothing in this document

shall operate as an express or implied license or indemnity under the intellectual property rights of Lenovo or

third parties. All information contained in this document was obtained in specific environments and is

presented as an illustration. The result obtained in other operating environments may vary.

Lenovo may use or distribute any of the information you supply in any way it believes appropriate without

incurring any obligation to you.

Any references in this publication to non-Lenovo Web sites are provided for convenience only and do not in

any manner serve as an endorsement of those Web sites. The materials at those Web sites are not part of the

materials for this Lenovo product, and use of those Web sites is at your own risk.

Any performance data contained herein was determined in a controlled environment. Therefore, the result

obtained in other operating environments may vary significantly. Some measurements may have been made

on development-level systems and there is no guarantee that these measurements will be the same on

generally available systems. Furthermore, some measurements may have been estimated through

extrapolation. Actual results may vary. Users of this document should verify the applicable data for their

specific environment.

66 M920s User Guide and Hardware Maintenance Manual

Appendix B. Trademarks

LENOVO, LENOVO logo, and the THINKCENTRE logo are trademarks of Lenovo. DisplayPort is a trademark

of the Video Electronics Standards Association. USB-C is a trademark of USB Implementers Forum. All other

68 M920s User Guide and Hardware Maintenance Manual

Table of Contents

Lenovo M920 User Manual

Related Manuals