Table of Contents
LG 49UH6030 User Manual
Displayed below is the user manual for 49UH6030 by LG which is a product in the TVs category. This manual has pages.
Related Manuals
OWNER’S MANUAL
Safety and Reference
LED TV*
* LG LED TVs are LCD TVs with LED backlighting.
P/No : MFL69272402 (1607-REV07)
www.lg.com
*MFL69272402*
Please read this manual carefully before operating your TV and
retain it for future reference.
43UH6500
49UH6500
55UH6550
60UH6550
65UH6550
75UH6550
60UH6035
43UH7500
49UH7500
55UH7500
60UH7500
65UH7500
55UH7650
60UH7650
65UH7650
49UH7700
55UH7700
60UH7700
65UH7700
55UH8500
60UH8500
65UH8500
75UH8500
65UH9500
86UH9500
49UH610A
55UH615A
60UH615A
65UH615A
55UH6150
60UH6150
65UH6150
43UH610A
43UH6030
49UH6030
55UH6030
60UH6030
65UH6030
70UH6330
43UH6100
49UH6100
49UH6090
55UH6090
60UH6090
50UH6300
58UH6300
70UH6350
2
ENGLISH
Important Safety Instructions
Always comply with the following precautions
to avoid dangerous situations and ensure peak
performance of your product.
WARNING/CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK). NO
USER SERVICEABLE PARTS INSIDE. REFER TO
QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead
symbol, within an equilateral triangle, is
intended to alert the user to the presence of
uninsulated dangerous voltage within the
product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock
to persons.
The exclamation point within an
equilateral triangle is intended to alert the
user to the presence of important operating
and maintenance (servicing) instructions in the
literature accompanying the device.
WARNING/CAUTION
- TO REDUCE THE RISK OF FIRE AND ELECTRIC
SHOCK, DO NOT EXPOSE THIS PRODUCT TO
RAIN OR MOISTURE.
WARNING
If you ignore the warning message, you may
be seriously injured or there is a possibility of
accident or death.
CAUTION
If you ignore the caution message, you may
be slightly injured or the product may be
damaged.
NOTE
The note helps you understand and use the
product safely. Please read the note carefully
before using the product.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
•Do not use this apparatus near water.
•Clean only with dry cloth.
•Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
•Do not install near any heat sources such
as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
•Do not defeat the safety purpose of the
polarized or grounding-type plug. A polarized
plug has two blades with one wider than the
other. A grounding type plug has two blades
and a third grounding prong. The wide blade or
the third prong are provided for your safety. If
the provided plug does not fit into your outlet,
consult an electrician for replacement of the
obsolete outlet.
•Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
•Only use attachments/accessories specified by
the manufacturer.
•Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
WARNING: This product contains chemicals known
to the State of California to cause cancer and birth
defects or other reproductive harm.
Wash hands
after handling.
3
ENGLISH
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to
avoid injury from tip-over.
•Unplug this apparatus during lightning storms or
when unused for long periods of time.
•Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not
operate normally, or has been dropped.
•Do not press strongly upon the panel with a hand
or a sharp object such as a nail, pencil, or pen, or
make a scratch on it.
•Do not stick metal objects or any other conductive
material into the power cord. Do not touch the end
of the power cord while it is plugged in.
•Keep the packing anti-moisture material or vinyl
packing out of the reach of children. Anti-moisture
material is harmful if swallowed. If swallowed,
induce vomiting and go to the nearest hospital.
Additionally, vinyl packing can cause suffocation.
Keep it out of the reach of children.
•CAUTION concerning the Power Cord
(Can differ by country):
Check the specification page of this owner’s
manual to be certain concerning current
requirements. Do not connect too many devices
to the same AC power outlet as this could result in
fire or electric shock. Do not overload wall outlets.
Overloaded wall outlets, loose or damaged wall
outlets, extension cords, frayed power cords, or
damaged or cracked wire insulation are dangerous.
Any of these conditions could result in electric
shock or fire. Periodically examine the cord of your
device, and if its appearance indicates damage
or deterioration, unplug it, discontinue use of the
device, and have the cord replaced with an exact
replacement part by an authorized servicer. Protect
the power cord from physical or mechanical abuse,
such as being twisted, kinked, pinched, closed in
a door, or walked upon. Pay particular attention
to plugs, wall outlets, and the point where the
cord exits the device. Do not move the TV with the
power cord plugged in. Do not use a damaged or
loose power cord. Be sure do grasp the plug when
unplugging the power cord. Do not pull on the
power cord to unplug the TV.
•Warning - To reduce the risk of fire or electrical
shock, do not expose this product to rain, moisture
or other liquids. Do not touch the TV with wet
hands. Do not install this product near flammable
objects such as gasoline or candles, or expose the
TV to direct air conditioning.
•Do not expose to dripping or splashing and do
not place objects filled with liquids, such as vases,
cups, etc. on or over the apparatus (e.g., on shelves
above the unit).
4
ENGLISH
•Grounding
- (Except for devices which are not grounded.)
Ensure that you connect the earth ground wire
to prevent possible electric shock (i.e., a TV
with a three-prong grounded AC plug must
be connected to a three-prong grounded AC
outlet).
If grounding methods are not possible, have
a qualified electrician install a separate circuit
breaker. Do not try to ground the unit by
connecting it to telephone wires, lightning
rods, or gas pipes.
Circuit
Breaker
Power
Supply
•As long as this unit is connected to the AC wall
outlet, it is not disconnected from the AC power
source even if the unit is turned off.
•Do not attempt to modify this product in any
way without written authorization from LG
Electronics. Unauthorized modification could
void the user’s authority to operate this product.
•Outdoor Antenna Grounding
- (Can differ by country):
If an outdoor antenna is installed, follow
the precautions below. An outdoor antenna
system should not be located in the vicinity of
overhead power lines or other electric light or
power circuits, or where it can come in contact
with such power lines or circuits as death or
serious injury can occur. Be sure the antenna
system is grounded to provide some protection
against voltage surges and built-up static
charges. Section 810 of the National Electrical
Code (NEC) in the U.S.A. provides information
with respect to proper grounding of the mast
and supporting structure, grounding of the
lead-in wire to an antenna discharge unit, size
of grounding conductors, location of antenna
discharge unit, connection to grounding
electrodes, and requirements for the grounding
electrode.
Antenna grounding according to the National
Electrical Code, ANSI/NFPA 70
Ground Clamp
Grounding Conductor
(NEC Section 810-21)
Antenna Lead in Wire
Electric Service
Equipment
Antenna Discharge Unit
(NEC Section 810-20)
Ground Clamp Power Service Grounding
Electrode System
(NEC Art 250, Part H)
NEC: National Electrical Code
•Cleaning
- When cleaning, unplug the power cord and
wipe gently with a soft cloth to prevent
scratching. Do not spray water or other liquids
directly on the TV as electric shock may occur.
Do not clean with chemicals such as alcohol,
thinners, or benzene.
•Moving
- Make sure the product is turned off, unplugged,
and all cables have been removed. It may take 2
or more people to carry larger TVs. Do not press
or put stress on the front panel of the TV.
•Ventilation
- Install your TV where there is proper ventilation.
Do not install in a confined space such as a
bookcase. Do not cover the product with cloth
or other materials while plugged in. Do not
install in excessively dusty places.
•If you smell smoke or other odors coming from
the TV, unplug the power cord and contact an
authorized service center.
•Keep the product away from direct sunlight.
•Never touch this apparatus or antenna during a
lightning storm.
•When mounting a TV on the wall, make sure not
to install the TV by hanging the power and signal
cables on the back of the TV.
•Do not allow an impact shock or any objects to
fall into the product, and do not drop anything
onto the screen.
•DISCONNECTING THE DEVICE FROM THE MAIN
POWER
The power plug is the disconnecting device.
In case of an emergency, the power plug must
remain readily accessible.
•Make sure the power cord is connected securely
to the power plug on the TV.
•Batteries
- Store the accessories (battery, etc.) in a safe
location out of the reach of children.
•This apparatus uses batteries. In your community
there might be regulations that require you
to dispose of these batteries properly due to
environmental considerations. Please contact
your local authorities for disposal or recycling
information.
•Do not dispose of batteries in a fire.
•Do not short circuit, disassemble, or allow the
batteries to overheat.
5
ENGLISH
•Do not use high voltage electrical equipment
near the TV, (e.g., a bug zapper).
This may result in product malfunction.
•Dot Defect
- This panel is an advanced product that contains
millions of pixels. In a very few cases, you could
see fine dots on the screen while you’re viewing
the TV. Those dots are deactivated pixels and
do not affect the performance and reliability
of the TV.
•Generated Sound
- Cracking noise A cracking noise that occurs
when watching or turning off the TV is
generated by plastic thermal contraction
due to temperature and humidity. This noise
is common for products where thermal
deformation is required.
- Electrical circuit humming/panel buzzing
A low level noise is generated from a high-
speed switching circuit, which supplies a
large amount of current to operate a product.
It varies depending upon the product.
This generated sound does not affect the
performance and reliability of the product.
•Take care not to touch the ventilation openings.
When watching the TV for a long period, the
ventilation openings may become hot. This does
not affect the performance of the product or
cause defects in the product.
•Do not install this product on a wall if it could be
exposed to oil or oil mist. This may damage the
product and cause it to fall.
•If the TV feels cold to the touch, there may
be a small flicker when it is turned on. This is
normal; there is nothing wrong with TV. Some
minute dot defects may be visible on the screen,
appearing as tiny red, green, or blue spots.
However, they have no adverse effect on the TV’s
performance. Avoid touching the LCD screen or
holding your finger(s) against it for long periods
of time. Doing so may produce some temporary
distortion effects on the screen.
•Displaying a still image for a prolonged time may
cause image sticking. Avoid displaying a fixed
image on the TV screen for a long period of time.
Viewing 3D Imaging
(For 3D models)
CAUTION
•Guardians should not leave children
unsupervised who are watching a 3D video.
Guardians should make children stop watching
the video and take a rest if they experience eye
fatigue, headache, or dizziness.
•When viewing a 3D video, some may experience
discomfort such as a headache, dizziness,
fatigue, or blurred vision. In this case, stop
watching the 3D video and take a rest.
•If you watch a 3D video for a long time, you
may experience eye fatigue. In this case, stop
watching the 3D video and take a rest.
•Only use LG 3D glasses. Otherwise, you may not
be able to view 3D videos properly.
•Do not use 3D glasses instead of your normal
glasses, sunglasses, or protective goggles. Place
the 3D glasses over your normal eye ware.
•Do not keep your 3D glasses in extremely high or
low temperatures. It will cause deformation.
•Do not use the 3D glasses while walking or
moving around. It may cause an accident or
injury.
•Be careful not to poke your eye with the frames
of the 3D glasses.
•Do not watch 3D content if you have
photosensitive seizures, epilepsy, or heart
disease.
6
ENGLISH
Preparing
NOTE
•When the TV is turned on for the first time after
being shipped from the factory, initialization of
the TV may take approximately one minute.
•Image shown may differ from your TV.
•Your TV’s OSD (On Screen Display) may differ
slightly from that shown in this manual.
•The available menus and options may differ from
the input source or product model that you are
using.
•New features may be added to this TV in the
future.
•The items supplied with your product may vary
depending upon the model.
•Product specifications or contents of this manual
may be changed without prior notice due to
upgrade of product functions.
•For an optimal connection, HDMI cables and
USB devices should have bezels less than 10 mm
(0.39 inches) thick and 18 mm (0.7 inches) width.
•Use an extension cable that supports USB 2.0 if
the USB cable or USB flash drive does not fit into
your TV’s USB port.
•Use a certified cable with the HDMI logo
attached. If you do not use a certified HDMI
cable, the screen may not display or a
connection error may occur.
•Recommended HDMI cable types (3 m or less)
- High-Speed HDMI®/TM cable
- High-Speed HDMI ®/TM cable with Ethernet
B
AA
B
*A 10 mm (0.39 inches)
*B 18 mm (0.7 inches)
•How to use the ferrite core
(Depending upon model)
- Use the ferrite core to reduce the
electromagnetic interference in the power
cable. Wind the power cable on the ferrite core
once.
[Cross Section of Ferrite Core]
[to a wall plug] [to the TV]
10 cm (+/- 2 cm)
•Antenna Isolator Installation Guide
(Depending upon model)
- Use this to install TV in a place where there is a
voltage difference between TV Set and GND of
antenna signal. If there is a voltage difference
between TV Set and GND of antenna signal, the
antenna contact might be heated and excessive
heat might cause an accident.
- You can improve the safety when watching
TV by efficiently removing power voltage
from TV antenna. It is recommended to
mount the isolator to the wall. If it cannot
be mounted to the wall, mount it on the TV.
Avoid disconnecting the antenna Isolator after
installation.
- Before starting, be sure that the TV antenna is
connected.
ANTENNA/
CABLE IN
Wall
or
Isolator
1. Connect to TV
2. Connect to Set-Top box
Cable /
Antenna
Connect one end of the isolator to cable/antenna
jack and the other to TV set or set-top box.
“Equipment connected to the protective earthing
of the building installation through the mains
connection or through other equipment with
a connection to protective earthing - and to a
cable distribution system using coaxial cable,
may in some circumstances create a fire hazard.
Connection to a cable distribution system has
therefore to be provided through a device
providing electrical isolation below a certain
frequency range (galvanic isolator, see EN 60728-
11)”
When applying the RF Isolator, a slight loss of
signal sensitivity can occur.
7
ENGLISH
CAUTION
•Do not use any unapproved items to ensure the
safety and product’s lifespan.
•Any damages or injuries by using unapproved
items are not covered by the warranty.
•Some models appear to have a thin film on the
screen. It is actually part of the screen; do not
remove it.
•When attaching the stand to the TV set, place
the screen facing down on a cushioned table or
flat surface to protect the screen from scratches.
•Make sure that the screws are fastened tightly.
(If they are not fastened securely enough, the TV
may tilt forward after being installed.)
•Do not fasten the screws with excessive force;
otherwise, they may be worn out and become
loose.
•Make sure to wring any excess water or cleaner
from the cloth.
•Do not spray water or cleaner directly onto the
TV screen.
•Make sure to spray just enough of water or
cleaner onto a dry cloth to wipe the screen.
•When cleaning the product, be careful not to
allow any liquid or foreign objects to enter the
gap between the upper, left or right side of the
panel and the guide panel. (For UH8500 series)
Optional Extras
Optional extras can be changed or modified for
quality improvement without any notification.
Contact your dealer for buying these items.
These devices work only with certain models.
The model name or design may be changed due to
the manufacturer’s circumstances or policies.
(Depending upon model)
AG-F***
Cinema 3D
Glasses
AG-F***DP
Dual Play
Glasses
AN-VC550
Smart Camera
AN-MR650
Magic Remote
Lifting and Moving the TV
When moving or lifting the TV, read the following
to prevent the TV from being scratched or
damaged and for safe transportation regardless of
its type and size.
•It is recommended to move the TV in the box or
packing material that the TV originally came in.
•Before moving or lifting the TV, disconnect the
power cord and all cables.
•When holding the TV, the screen
should face away from you to
avoid damage.
•Hold the top and bottom of the TV frame firmly.
Make sure not to hold the transparent part,
speaker, or speaker grille area.
•Use at least two people to move
a large TV.
•When transporting the TV by
hand, hold the TV as shown in the
following illustration.
•When transporting the TV, do not expose the TV
to jolts or excessive vibration.
•When transporting the TV, keep the TV upright;
never turn the TV on its side or tilt towards the
left or right.
•When handling the TV, be careful not to damage
the protruding buttons.
8
ENGLISH
CAUTION
•Avoid touching the screen at all times, as this
may result in damage to the screen.
•Do not place the product on the floor with its
front facing down without padding. Failure to do
so may result in damage to the screen.
•Do not move the TV by holding the cable
holders, as the cable holders may break, and
injuries and damage to the TV may occur.
(Depending upon model)
Using the Button
(Depending upon model)
You can simply operate the TV functions, pressing
or moving the button.
NOTE
•43/49UH6030, 43/49UH6100, 49UH6090, and
43/49UH610A does not have a Joystick button
but has only a power On/Off button.
(A Type)
Dome Button Joystick Button
Button
Or Or
(B Type)
Joystick Button
Basic Functions
Power On (Press)
Power Off (Press and Hold)1
Volume Control
Channels Control
1 All running apps will close.
Adjusting the Menu
When the TV is turned on, press button one time.
You can adjust the Menu items pressing or moving
the buttons.
Turns the power off.
Accesses the setting menu.
Clears on-screen displays and returns to TV
viewing.
Changes the input source.
Mounting on a Table
1 Lift and tilt the TV into its upright position on a
table.
- Leave a 10 cm (4 inches) (minimum) space from
the wall for proper ventilation.
10 cm
10 cm
10 cm
10 cm
10 cm
(4 inches)
2 Connect the power cord to a wall outlet.
9
ENGLISH
CAUTION
•Do not place the TV near or on sources of heat,
as this may result in fire or other damage.
Securing the TV to a Wall
(optional)
(Depending upon model)
1 Insert and tighten the eye-bolts, or TV brackets
and bolts on the back of the TV.
- If there are bolts inserted at the eye-bolts
position, remove the bolts first.
2 Mount the wall brackets with the bolts to the
wall. Match the location of the wall bracket and
the eye-bolts on the rear of the TV.
3 Connect the eye-bolts and wall brackets tightly
with a sturdy rope or cable. Make sure to keep
the rope parallel to the flat surface.
CAUTION
•Make sure that children do not climb on or hang
on the TV.
NOTE
•Use a platform or cabinet that is strong and large
enough to support the TV securely.
•Brackets, bolts, and ropes are optional. You can
obtain additional accessories from your local
dealer.
Mounting on a Wall
An optional wall mount can be used with your
LG Television. Consult with your local dealer for
a wall mount that supports the VESA standard
used by your TV model. Carefully attach the wall
mount bracket at the rear of the TV. Install the wall
mount bracket on a solid wall perpendicular to the
floor. If you are attaching the TV to other building
materials, please contact qualified personnel to
install the wall mount. Detailed instructions will
be included with the wall mount. We recommend
that you use an LG brand wall mount. The LG wall
mount is easy to adjust or to connect the cables.
When you do not use LG’s wall mount bracket,
use a wall mount bracket where the device is
adequately secured to the wall with enough space
to allow connectivity to external devices. If you are
using a non-adjustable mount, attach the mount
to the wall. Attach the cables to the TV first, then
attach the TV to the mount.
10 cm
10 cm
10 cm
10 cm
(4 inches)
Make sure to use screws and wall mounts that
meet the VESA standard. Standard dimensions for
the wall mount kits are described in the following
table.
10
ENGLISH
Model 50UH6300
49UH610A
55UH615A
49UH6100
49UH6090
55UH6090
55UH6150
49UH6500
55UH6550
49/55UH7500
49/55UH7700
55UH8500
55UH7650
49/55UH6030
58UH6300
60/65UH615A
60/65UH6150
60/65UH6550
60/65UH7500
60/65UH7700
60/65UH8500
60/65UH7650
60UH6090
60/65UH6030
60UH6035
VESA (A x B) 300 x 300 300 x 300
Standard screw M6 M6
Number of
screws 4 4
Wall mount
bracket
(optional)
LSW350B
MSW240 LSW350B
Model 43UH6100
43UH6500
43UH7500
43UH610A
43UH6030
75UH6550
75UH8500
86UH9500
70UH6350
70UH6330
VESA (A x B) 200 x 200 600 x 400
Standard screw M6 M8
Number of
screws 4 4
Wall mount
bracket
(optional)
LSW240B
MSW240 LSW640B
Model 65UH9500
VESA (A x B) 300 x 200
Standard screw M6
Number of
screws 4
Wall mount
bracket
(optional)
OTW420B
A
B
CAUTION
•Remove the stand before installing the TV on a
wall mount by performing the stand attachment
in reverse.
NOTE
•When using the wall mount, it is recommended
that you apply a piece of tape over the 2 Pole
Stand holes to prevent dust and bugs from
entering the holes. (Depending upon model)
2 Pole Stand Hole
•When using the wall mounting bracket, apply
the adhesive protective label or protective cover
to cover the unused stand openings. This will
prevent the accumulation of dust and dirt. (Use
only when provided with your particular model.)
Provided Item
Adhesive Protective
Label
Provided Item
Adhesive Protective
Label
Provided Item
Protective Cover
•Depending upon the shape of the stand, use a
flat tool to remove the stand cover as illustrated
below. (e.g., a flat screwdriver)
11
ENGLISH
Connections (Notifications)
You can connect various external devices to the TV.
Supported external devices are: HD receivers, DVD
players, VCRs, audio systems, USB storage devices,
PC, gaming devices, and other external devices.
For more information on an external device’s
connection, refer to the manual provided with
each device.
NOTE
•If you record a TV program on a DVD recorder or
VCR, make sure to connect the TV signal input
cable to the TV through a DVD recorder or VCR.
For more information about recording, refer to
the manual provided with the connected device.
•The external device connections shown may
differ slightly from illustrations in a manual.
•Connect external devices to the TV regardless
about the order of the TV port.
•If you connect a gaming device to the TV, use the
cable supplied with the gaming device.
•Refer to the external equipment’s manual for
operating instructions.
•In PC mode, there may be noise associated
with the resolution, vertical pattern, contrast,
or brightness. If noise is present, change the PC
output to another resolution, change the refresh
rate to another rate, or adjust the brightness and
contrast on the PICTURE menu until the picture
is clear.
•Depending upon the graphics card, some
resolution settings may not allow the image to
be positioned on the screen properly.
•Some USB Hubs may not work. If a USB device
connected through a USB Hub is not detected,
connect it directly to the USB port on the TV.
•The TV may be capable of operating without a
set-top from a multichannel video programming
distributor (MVPD).
Connecting to an Antenna or
Cable
Connect an antenna, cable, or cable box to watch
TV. The illustrations may differ from the actual
items and an RF cable is optional.
CAUTION
•Make sure not to bend the copper wire of the RF
cable.
Copper Wire
•Complete all connections between devices, and
then connect the power cord to the power outlet
to prevent damage to your TV.
NOTE
•Use a signal splitter to use 2 TVs or more.
•DTV Audio Supported Codec: MPEG,
Dolby Digital.
•Direct ULTRA HD broadcast is unavailable in
areas without an ULTRA HD signal.
•This TV cannot receive ULTRA HD (3840 x 2160
pixels) broadcasts directly because the related
standards have not been confirmed. (Depending
upon model)
Other Connections
Connect your TV to external devices. For the best
picture and audio quality, connect the external
device and the TV with the HDMI cable. Depending
upon the model, a cable may not be provided.
NOTE
• > > > General >
HDMI ULTRA HD Deep Color:
- On : Support 4K @ 60 Hz (4:4:4, 4:2:2, 4:2:0)
- Off : Support 4K @ 60 Hz 8bit (4:2:0)
•If the device connected to Input Port also
supports ULTRA HD Deep Color, your picture
may be clearer. However, if the device doesn’t
support it, it may not work properly. In that case,
connect the device to a different HDMI port or
change the TV’s HDMI ULTRA HD Deep Color
setting to Off.
- This feature is available only on certain models
which support HDMI ULTRA HD Deep Color.
•HDMI Audio Supported Format:
DTS (44.1 kHz / 48 kHz),
AC3 (32 kHz / 44.1 kHz / 48 kHz),
PCM (32 kHz / 44.1 kHz / 48 kHz / 96 kHz / 192 kHz)
(Depending upon model)
12
ENGLISH
Remote Control
(Depending upon model)
The descriptions in this manual are based on
the buttons on the remote control. Please read
this manual carefully and use the TV correctly. To
install batteries, open the battery cover, replace
batteries (1.5 V AAA) matching the and ends
to the label inside the compartment, and close
the battery cover. Failure to match the correct
polarities of the battery may cause the battery
to burst or leak, resulting in fire, personal injury,
or ambient pollution. To remove the batteries,
perform the installation actions in reverse. This
remote uses infrared light. When in use, it should
be pointed in the direction of the TV’s remote
sensor.
A
A
(POWER) Turns the TV on or off.
INPUT Changes the input source.
Activates or deactivates the subtitles.
(User Guide) Sees user-guide.
(Search) Shows the search mode.
Returns to the last TV channel.
Number button Enters numbers.
- (Dash) Inserts a dash between numbers such as
2-1 and 2-2.
Accesses the saved channel list.
Alternates between the two last channels
selected (pressing repeatedly).
Adjusts the volume level.
Accesses your favorite channel list.
Shows information on the current program.
Mutes all sounds.
Scrolls through the saved channels.
Moves to the previous or next screen.
B
B
Shows the previous history.
(Home) Accesses the Home menu.
Shows the list of Channels.
(Settings) Accesses the settings.
By zooming in on the selected area, you
can view it in full screen.
Navigation buttons Scrolls through menus or
options. (up/down/left/right)
Selects menus or options and confirms your
input.
Returns to the previous screen.
Clears all on-screen displays and returns to TV
viewing.
Enables SAP (Secondary Audio Program)
Feature.
Sets the length of time until the TV to turns
off.
, , , , Control buttons for media contents
Color buttons These access special functions in
some menus. ( , , , )
13
ENGLISH
Magic Remote Functions
(Depending upon model)
When the message
Magic remote battery is low.
Change the battery.
is displayed, replace the
batteries. To install batteries, open the battery
cover, replace batteries (1.5 V AA) matching and
ends to the label inside the compartment, and
close the battery cover. Failure to match the correct
polarities of the battery may cause the battery to
burst or leak, resulting in fire, personal injury, or
ambient pollution. Be sure to point the remote
control at the remote control sensor on the TV.
To remove the batteries, perform the installation
actions in reverse.
This remote uses infrared light and Bluetooth
technology. When in use, it should be pointed in
the direction of the TV’s remote sensor.
A
A
(POWER) Turns the TV on or off.
(STB POWER) You can turn your set-top box
on or off by adding the set-top box to the universal
remote control for your TV.
Number button Enters numbers.
- (Dash) Inserts a dash between numbers such as
2-1 and 2-2.
Accesses the saved channel list.
(Screen Remote) Displays the Screen Remote.
•Accesses the Universal Control Menu in some
regions.
B
C
B
Adjusts the volume level.
(MUTE) Mutes all sounds.
* Video descriptions function will be enabled.
•SAP (Secondary Audio Program) Feature can also
be enabled by pressing the key.
Scrolls through the saved channels.
(Home) Accesses the Home menu.
* Shows the previous history.
(Search) Search for content such as channels,
movies and other videos, or perform a web search
by entering your search terms in the search box.
(Voice recognition) Network connection is
required to use the voice recognition function.
1 Press and hold the (Search) button.
2 Speak when the voice display window appears
on the TV screen.
Displays the set-top box Home menu.
(When you are not watching with a set-top box:
the set-top box screen is displayed.)
14
ENGLISH
C
(up/down/left/right) Press the up, down,
left or right button to scroll the menu. If you press
buttons while the pointer is in use, the
pointer will disappear from the screen and Magic
Remote will operate like a general remote control.
To display the pointer on the screen again, shake
Magic Remote to the left and right.
Wheel (OK) Press the center of the Wheel
button to select a menu. You can change channels
by using the Wheel button.
Returns to the previous screen.
* Clears all on-screen displays and returns to
TV viewing.
Used for viewing 3D video. (For 3D models)
INPUT Changes the input source.
• Pressing and holding the INPUT button
displays all the lists of external inputs.
Activates or deactivates the subtitles.
(Q. Settings) Accesses the quick settings.
• Pressing and holding the (Q. Settings) button
displays the All Settings menu.
Color buttons These access special functions in
some menus.
( Red, Green, Yellow, Blue)
, Control buttons for media contents
You can zoom in on the area where the
remote control is pointed.
* By zooming in on the selected area,
you can view it in full screen.
* : To use the button, press and hold for more than
3 seconds.
Registering Magic Remote
How to Register the Magic Remote
To use the Magic Remote, first pair it with your TV.
1 Put batteries into the Magic Remote and turn the
TV on.
2 Point the Magic Remote at your TV and press the
Wheel (OK) on the remote control.
•If the TV fails to register the Magic Remote, try
again after turning the TV off and back on.
How to Deregister the Magic Remote
Press the and (Home) buttons
at the same time, for five seconds, to unpair the
Magic Remote with your TV.
•Pressing and holding the button will
let you cancel and re-register Magic Remote at
once.
Licenses
Supported licenses may differ by model.
For more information about licenses, visit
www.lg.com.
(For UH7650, UH7700,
UH8500, UH9500
series)
Open Source Software Notice
Information
To obtain the source code under GPL, LGPL, MPL,
and other open source licenses, that is contained
in this product, please visit
http://opensource.lge.
com.
In addition to the source code, all referred license
terms, warranty disclaimers and copyright notices
are available for download.
LG Electronics will also provide open source code
to you on CD-ROM for a charge covering the cost
of performing such distribution (such as the cost of
media, shipping, and handling) upon email request
to
opensource@lge.com
. This offer is valid for three
(3) years from the date on which you purchased
the product.
15
ENGLISH
Troubleshooting
•Cannot control the TV with the remote control.
- Check if anything such as tape has been placed
over the receiver.
- Check if there is any obstacle between the
product and the remote control.
- Replace the batteries with new ones.
•No image display and no sound is produced.
- Check if the product is turned on.
- Check if the power cord is connected to a wall
outlet.
- Check if there is a problem in the wall outlet by
connecting other products.
•The TV turns off suddenly.
- Check the power control settings. The power
supply may be interrupted.
- Check if the Sleep Timer / Timer Power Off
feature is activated in the Timers settings.
- If there is no signal while the TV is on, the TV
will turn off automatically after 15 minutes of
inactivity.
Specifications
Product specifications may be changed without
prior notice due to upgrade of product functions.
Estimated yearly energy consumption indicated on
the FTC label is measured in accordance with the
Test Procedures for Television Sets (USA only).
The actual energy consumption depends on the
usage environment (the content watched, TV
settings, etc.).
Television System
ATSC, NTSC-M, 64 & 256 QAM
Program Coverage
VHF 2-13, UHF 14-69, DTV 2-69, CATV 1-135,
CADTV 1-135
External Antenna Impedance
75 Ω
Environment Condition
•Operating Temperature
0 °C to 40 °C (32 °F to 104 °F)
•Operating Humidity
Less than 80 %
•Storage Temperature
- 20 °C to 60 °C (-4 °F to 140 °F)
•Storage Humidity
Less than 85 %
Wireless Module Specifications
(For UH6330, UH6300, UH6350, UH6500, UH6550,
UH7500, UH7650, UH7700, UH8500, UH9500,
series)
Wireless Module(LGSBWAC61)Specifications
Wireless LAN (IEEE 802.11a/b/g/n/ac)
Frequency Range Output Power(Max.)
2400 to 2483.5 MHz
5150 to 5725 MHz
5725 to 5850 MHz
15 dBm
16 dBm
12.5 dBm
Bluetooth
Frequency Range Output Power(Max.)
2400 to 2483.5 MHz 10 dBm
As band channels can vary per country, the user
cannot change or adjust the operating frequency.
This product is configured for the regional
frequency table.
For consideration of the user, this device should
be installed and operated with a minimum
distance of 20 cm (7.8 inches) between the device
and the body.
FCC ID: BEJLGSBWAC61
IC: 2703H-LGSBWAC61
16
ENGLISH
(For UH6035, UH6030, UH610A, UH6100, UH6150,
UH615A, UH6090 series)
Wireless LAN Module(WN8122E1) Specification
Standard IEEE802.11a/b/g/n
Frequency Range
2400 to 2483.5 MHz
5150 to 5250 MHz
5725 to 5850 MHz
Output Power
(Max.)
802.11a : 16.5 dBm
802.11b : 16 dBm
802.11g : 15.5 dBm
802.11n - 2.4GHz : 15.5 dBm
802.11n - 5GHz : 16.5 dBm
As band channels can vary per country, the user
cannot change or adjust the operating frequency.
This product is configured for the regional
frequency table.
For consideration of the user, this device should
be installed and operated with a minimum
distance of 20 cm (7.8 inches) between the device
and the body.
Contains FCC ID: BEJWN8122E1
Contains IC: 2703H-WN8122E1
External Control Device Setup
To obtain the external control device setup
information, please visit
www.lg.com
.
17
ENGLISH
Regulatory
FCC Notice
(For USA)
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential
installation. This equipment generates, uses,
and can radiate radio frequency energy and, if
not installed and used in accordance with the
instructions, may cause harmful interference
to radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning
the equipment off and on, the user is encouraged
to try to correct the interference by one or more of
the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the
equipment and the receiver.
- Connect the equipment to an outlet on a circuit
different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV
technician for help.
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful
interference and (2) this device must accept any
interference received, including interference that
may cause undesired operation of the device.
Any changes or modifications in construction of
this device which are not expressly approved by
the party responsible for compliance could void
the user’s authority to operate the equipment.
FCC Radio Frequency Interference
Requirements (for UNII devices)
High power radars are allocated as primary users
of the 5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands.
These radar stations can cause interference with
and/or damage this device. This device cannot be
co-located with any other transmitter.
FCC RF Radiation Exposure Statement
[For having wireless function (WLAN, Bluetooth,...)]
This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled
environment. This transmitter must not be co-
located or operating in conjunction with any other
antenna or transmitter.
This equipment should be installed and operated
with minimum distance 20 cm (7.8 inches)
between the antenna and your body. Users must
follow the specific operating instructions for
satisfying RF exposure compliance.
Industry Canada Statement
(For Canada)
[For having wireless function (WLAN, Bluetooth,...)]
This device complies with Industry Canada’s
licence-exempt RSSs. Operation is subject to the
following two conditions:
1 This device may not cause interference; and
2 This device must accept any interference,
including interference that may cause undesired
operation of the device.
IC Radiation Exposure Statement
(For Canada)
[For having wireless function (WLAN, Bluetooth,...)]
This equipment complies with IC radiation
exposure limits set forth for an uncontrolled
environment. This equipment should be installed
and operated with minimum distance 20 cm (7.8
inches) between the antenna & your body.
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE
FOR ANY RADIO OR TV INTERFERENCE CAUSED
BY UNAUTHORIZED MODIFICATIONS TO THIS
EQUIPMENT. SUCH MODIFICATIONS COULD
VOID THE USER’S AUTHORITY TO OPERATE THE
EQUIPMENT.
WARNING
(For Canada)
[For product having the wireless function using 5
GHz frequency bands]
1 The device for operation in the band 5150–5250
MHz is only for indoor use to reduce the
potential for harmful interference to co-channel
mobile satellite systems;
2 For devices with detachable antenna(s), the
maximum antenna gain permitted for devices in
the bands 5250-5350 MHz and 5470-5725 MHz
shall be such that the equipment still complies
with the e.i.r.p. limit;
3 For devices with detachable antenna(s), the
maximum antenna gain permitted for devices in
the band 5725-5850 MHz shall be such that the
equipment still complies with the e.i.r.p. limits
specified for point-to-point and non-point-to-
point operation as appropriate; and
18
ENGLISH
4 The worst-case tilt angle(s) necessary to remain
compliant with the e.i.r.p. elevation mask
requirement set forth in Section 6.2.2(3) shall be
clearly indicated.(devices operating in the band
5250-5350 MHz with a maximum e.i.r.p. greater
than 200 mW)
5 High-power radars are allocated as primary
users (i.e. priority users) of the bands 5250–5350
MHz and 5650–5850 MHz and that these radars
could cause interference and/or damage to LE-
LAN devices.
Note to Cable/TV Installer
(For USA and Canada)
This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the
National Electric Code (U.S.A.). The code provides
guidelines for proper grounding and, in particular,
specifies that the cable ground shall be connected
to the grounding system of the building, as close
to the point of the cable entry as practical.
WARNING!
Never place a television set in an unstable
location. A television set may fall, causing serious
personal injury or death. Many injuries, particularly
to children, can be avoided by taking simple
precautions such as:
- Using cabinets or stands recommended by the
manufacturer of the television set.
- Only using furniture that can safely support the
television set.
- Ensuring the television set is not overhanging
the edge of the supporting furniture.
- Not placing the television set on tall furniture
(for example, cupboards or bookcases) without
anchoring both the furniture and the television
set to a suitable support.
- Not placing the television set on cloth or other
materials that may be located between the
television set and supporting furniture.
- Educating children about the dangers of
climbing on furniture to reach the television set
or its controls.
If your existing television set is being retained
and relocated, the same considerations as above
should be applied.
Symbols
Refers to alternating current(AC).
Refers to direct current(DC).
Refers to class II equipment.
Refers to stand-by.
Refers to “ON” (power).
Refers to dangerous voltage.
THE CONSUMER ELECTRONICS INDUSTRY CARES
• Manufacturers, retailers and the rest of the consumer electronics industry are committed to
making home entertainment safe and enjoyable.
• As you enjoy your television, please note that all televisions – new and old- must be supported on
proper stands or installed according to the manufacturer’s recommendations. Televisions that
are inappropriately situated on dressers, bookcases, shelves, desks, speakers, chests, carts, etc.,
may fall over, resulting in injury.
TUNE IN TO SAFETY
• ALWAYS follow the manufacturer’s recommendations for the safe installation of your television.
• ALWAYS read and follow all instructions for proper use of your television.
• NEVER allow children to climb on or play on the television or the furniture on which the television
is placed.
• NEVER place the television on furniture that can easily be used as steps, such as a chest of
drawers.
• ALWAYS install the television where it cannot be pushed, pulled over or knocked down.
• ALWAYS route cords and cables connected to the television so that they cannot be tripped
over, pulled or grabbed.
WALL OR CEILING MOUNT YOUR TELEVISION
• ALWAYS contact your retailer about professional installation if you have any doubts about your
ability to safely mount your television.
• ALWAYS use a mount that has been recommended by the television manufacturer and has a
safety certication by an independent laboratory (such as UL, CSA, ETL).
• ALWAYS follow all instructions supplied by the television and mount manufacturers.
• ALWAYS make sure that the wall or ceiling where you are mounting the television is appropriate.
Some mounts are not designed to be mounted to walls and ceilings with steel studs or cinder
block construction. If you are unsure, contact a professional installer.
• Televisions can be heavy. A minimum of two people is required for a wall or ceiling mount
installation.
MOVING AN OLDER TELEVISION TO A NEW PLACE IN
YOUR HOME
• Many new television buyers move their older CRT televisions into a secondary room after the
purchase of a at-panel television. Special care should be made in the placement of older CRT
televisions.
• ALWAYS place your older CRT television on furniture that is sturdy and appropriate for its size
and weight.
• NEVER place your older CRT television on a dresser where children may be tempted to use the
drawers to climb.
• ALWAYS make sure your older CRT television does not hang over the edge of your furniture.
CHILD SAFETY:
PROPER TELEVISION PLACEMENT MATTERS
CE.org/safety
The model and serial numbers of the TV are located on
the back and on one side of the TV. Record them below
should you ever need service.
MODEL
SERIAL
LG Customer Information Center
For inquires or comments, visit www.lg.com or call;
1-800-243-0000 USA, Consumer User
1-888-865-3026 USA, Commercial User
1-888-542-2623 CANADA
Register your product Online!
www.lg.com
Declaration of Conformity
Trade Name: LG
Model: 43UH610A-UJ, 43UH6030-UB, 49UH6030-UB,
55UH6030-UC, 60UH6030-UC, 65UH6030-UC,
70UH6330-UB, 49UH610A-UJ, 55UH615A-UC,
60UH615A-UC, 65UH615A-UC, 43UH6100-UH,
49UH6100-UH, 49UH6090-UJ, 55UH6090-UF,
60UH6090-UF, 55UH6150-UB, 60UH6150-UB,
65UH6150-UB, 43UH6500-UB, 49UH6500-UB,
55UH6550-UB, 60UH6550-UB, 65UH6550-UB,
75UH6550-UB, 50UH6300-UA, 58UH6300-UA,
43UH7500-UA, 49UH7500-UA, 55UH7500-UA,
60UH7500-UA, 65UH7500-UA, 55UH7650-UA,
60UH7650-UA, 65UH7650-UA, 49UH7700-UB,
55UH7700-UB, 60UH7700-UB, 65UH7700-UB,
70UH6350-UB, 55UH8500-UA, 60UH8500-UA,
65UH8500-UA, 75UH8500-UD, 65UH9500-UA,
86UH9500-UA, 43UH6030-UD, 49UH6030-UD,
60UH6035-UC
Responsible Party: LG Electronics Inc.
Address: 1000 Sylvan Ave. Englewood Cliffs NJ 07632
U.S.A
TEL: 201-266-2534
OWNER’S MANUAL
EXTERNAL CONTROL
DEVICE SETUP
Please read this manual carefully before operating the set and retain it for
future reference.
www.lg.com
2
ENG
ENGLISH
2KEY CODES
KEY CODES
• This feature is not available for all models.
Code
(Hexa) Function Note Code
(Hexa) Function Note
00 CH +, PR + R/C Button 53 List R/C Button
01 CH -, PR - R/C Button 5B Exit R/C Button
02 Volume + R/C Button 60 PIP(AD) R/C Button
03 Volume - R/C Button 61 Blue R/C Button
06 > (Arrow Key / Right Key) R/C Button 63 Yellow R/C Button
07 < (Arrow Key / Left Key) R/C Button 71 Green R/C Button
08 Power R/C Button 72 Red R/C Button
09 Mute R/C Button 79 Ratio / Aspect Ratio R/C Button
0B Input R/C Button 91 AD (Audio Description) R/C Button
0E SLEEP R/C Button 9E LIVE MENU R/C Button
0F TV, TV/RAD R/C Button 7A User Guide R/C Button
10 - 19 * Number Key 0 - 9 R/C Button 7C Smart / Home R/C Button
1A Q.View / Flashback R/C Button 7E SIMPLINK R/C Button
1E FAV (Favorite Channel) R/C Button 8E ►►(Forward) R/C Button
20 Text (Teletext) R/C Button 8F ◄◄(Rewind) R/C Button
21 T. Opt (Teletext Option) R/C Button AA Info R/C Button
28 Return (BACK) R/C Button AB Program Guide R/C Button
30 AV (Audio / Video) Mode R/C Button B0 ►(Play) R/C Button
39 Caption/Subtitle R/C Button B1 ꕗ (Stop / File List) R/C Button
40 Λ
(Arrow Key / Cursor Up)
R/C Button B5 RECENT R/C Button
41 V (Arrow Key / Cursor
Down) R/C Button BA ꕘ (Freeze / Slow Play /
Pause) R/C Button
42 My Apps R/C Button BB Soccer R/C Button
43 Menu / Settings R/C Button BD ꔄ (REC) R/C Button
44 OK / Enter R/C Button DC 3D R/C Button
45 Q.Menu R/C Button 99 AutoConfig R/C Button
4C List, - (ATSC Only) R/C Button 9F App / * R/C Button
4D PICTURE R/C Button 9B TV / PC R/C Button
52 SOUND R/C Button
* Key code 4C (0x4C) is available on ATSC/ISDB models which use major/minor channel.
(For South Korea, Japan, North America, Latin America except Colombia models)
3
ENGENGLISH
3
EXTERNAL CONTROL DEVICE SETUP
EXTERNAL CONTROL DEVICE SETUP
• Image shown may differ from your TV.
Connect the USB to Serial converter/RS-232C input jack to an external control device (such as a computer
or an A/V control system) to control the product’s functions externally.
Note: The type of control port on the TV can be different between model series.
* Please be advised that not all models support this type of connectivity.
* Cable is not provided.
USB to Serial converter with USB Cable
USB Type
USB IN
(TV)
(PC)
(PC
)
RS-232C IN
(CONTROL & SERVICE)
(TV)
(TV)
(PC)
(TV)
(PC)
SERVICE ONLY
RS-232C IN
(CONTROL & SERVICE)
RS-232C IN
(CONTROL & SERVICE)
1
3
2
1
3
2
• LGTV supports PL2303 chip-based (Vendor ID : 0x0557, Product ID : 0x2008) USB to serial converter
which is not made nor provided by LG.
• It can be purchased from computer stores that carry accessories for IT support professionals.
RS-232C With RS232C Cable
DE9 (D-Sub 9pin) Type
• You need to purchase the RS-232C (DE9, D-Sub 9pin female-to-female type) to RS-232C cable required
for the connection between the PC and the TV, which is specified in the manual.
USB IN
(TV)
(PC
)
(PC)
RS-232C IN
(CONTROL & SERVICE)
(TV)
(TV)
(PC)
(TV)
(PC)
SERVICE ONLY
RS-232C IN
(CONTROL & SERVICE)
RS-232C IN
(CONTROL & SERVICE)
1
3
2
1
3
2
The connection interface may differ from your TV.
4
ENG
ENGLISH
4EXTERNAL CONTROL DEVICE SETUP
Phone jack Type
• You need to purchase the phone-jack to RS-232 cable required for the connection between the PC and
the TV, which is specified in the manual.
* For other models, connect to the USB port.
* The connection interface may differ from your TV.
USB IN
(TV)
(PC)
(PC)
RS-232C IN
(CONTROL & SERVICE)
(TV)
(TV)
(PC
)
(TV)
(PC)
SERVICE ONLY
RS-232C IN
(CONTROL & SERVICE)
RS-232C IN
(CONTROL & SERVICE)
1
3
2
1
3
2
- or
USB IN
(TV)
(PC)
(PC)
RS-232C IN
(CONTROL & SERVICE)
(TV)
(TV)
(PC)
(TV)
(PC
)
SERVICE ONLY
RS-232C IN
(CONTROL & SERVICE)
RS-232C IN
(CONTROL & SERVICE)
1
3
2
1
3
2
Customer Computer RS-232C configurations
3-Wire Configurations(Not standard)
1
6
5
9
PC TV
RXD 2 2 TXD
TXD 3 1 RXD
GND 5 3 GND
OR
RXD 3 2 TXD
TXD 2 1 RXD
GND 5 3 GND
D-Sub 9 Phone
RS-232C
(Serial port)
Set ID
For Set ID number, see "Real Data Mapping" on p.6
1. Press SETTINGS to access the main menus.
2. Press the Navigation buttons to scroll to (*General → About this TV or OPTION) and press OK.
3. Press the Navigation buttons to scroll to SET ID and press OK.
4. Scroll left or right to select a set ID number and select CLOSE. The adjustment range is 1-99.
5. When you are finished, press EXIT.
* (Depending on model)
5
ENGENGLISH
5
EXTERNAL CONTROL DEVICE SETUP
Communication Parameters
• Baud rate : 9600 bps (UART)
• Data length : 8 bits
• Parity : None
• Stop bit : 1 bit
• Communication code : ASCII code
• Use a crossed (reverse) cable.
Command reference list
(Depending on model)
COMMAND1 COMMAND2 DATA
(Hexadecimal) COMMAND1 COMMAND2 DATA
(Hexadecimal)
01. Power* k a 00 to 01 15. Balance k t 00 to 64
02. Aspect
Ratio k c (p.7)
16. Color
(Colour)
Temperature
x u 00 to 64
03. Screen
Mute k d (p.7)
17. ISM
Method (Only
Plasma TV)
j p (p.8)
04. Volume
Mute k e 00 to 01 18. Equalizer j v (p.8)
05. Volume
Control k f 00 to 64 19. Energy
Saving j q 00 to 05
06. Contrast k g 00 to 64 20. Tune
Command m a (p.9)
07.
Brightness k h 00 to 64
21. Channel
(Programme)
Add/Del(Skip)
m b 00 to 01
08. Color/
Colour k i 00 to 64 22. Key m c Key Codes
09. Tint k j 00 to 64
23. Control
Backlight,
Control Panel
Light
m g 00 to 64
10.
Sharpness k k 00 to 32 24. Input
select (Main)
x b (p.11)
11. OSD
Select k l 00 to 01 25. 3D (Only
3D models)
x t (p.11)
12. Remote
Control Lock
Mode
k m 00 to 01
26. Extended
3D (Only 3D
models)
x v (p.12)
13. Treble k r 00 to 64
27. Auto
Configure
j u (p.12)
14. Bass k s 00 to 64
* Note: During playing or recording media, all commands except Power (ka) and Key (mc) are not
executed and treated as NG.
With RS232C cable, TV can communicate "ka command" in power-on or power-off status. but with
USB-to-Serial converter cable, the command works only if TV is on.
6
ENG
ENGLISH
6EXTERNAL CONTROL DEVICE SETUP
Transmission / Receiving Protocol
Transmission
[Command1][Command2][ ][Set ID][ ][Data][Cr]
[Command 1] : First command to control the TV. (j, k, m or x)
[Command 2] : Second command to control the TV.
[Set ID] : You can adjust the [Set ID] to choose desired monitor ID number in option menu.
Adjustment range in TV is 1 to 99. If [Set ID] value is selected to ‘0’, every connected set
can be controlled.
* [Set ID] is indicated as decimal (1 to 99) on menu and as Hexadecimal (0x00 to 0x63) on
transmission/receiving protocol.
[DATA] : To transmit command data (hexadecimal). Transmit ‘FF’ data to read status of command.
[Cr] : Carriage Return - ASCII code ‘0x0D’
[ ] : Space – ASCII code ‘0x20’
OK Acknowledgement
[Command2][ ][Set ID][ ][OK][Data][x]
* The set transmits ACK (acknowledgement) based on this format when receiving normal data. At this time,
if the data is data read mode, it indicates present status data. If the data is data write mode, it returns the
data of the PC computer.
Error Acknowledgement
[Command2][ ][Set ID][ ][NG][Data][x]
* The set transmits ACK (acknowledgement) based on this format when receiving abnormal data from
non-viable functions or communication errors.
Data 00: Illegal Code
Real data mapping (Hexadecimal b Decimal)
* When you enter the [data] in hexadecimal, refer to following conversion table.
* Channel Tune (ma) Command uses two-byte hexadecimal value([data]) to select channel number.
00 : Step 0 32 : Step 50 (Set ID 50) FE : Step 254
01 : Step 1 (Set ID 1) 33 : Step 51 (Set ID 51) FF : Step 255
... ... ...
0A : Step 10 (Set ID 10) 63 : Step 99 (Set ID 99) 01 00 : Step 256
... ... ...
0F : Step 15 (Set ID 15) C7 : Step 199 27 0E : Step 9998
10 : Step 16 (Set ID 16) C8 : Step 200 27 0F : Step 9999
... ... ...
7
ENGENGLISH
7
EXTERNAL CONTROL DEVICE SETUP
* Commands may work differently depending on model and signal.
01. Power (Command: k a)
►To control Power *On or Off of the set.
Transmission[k][a][ ][Set ID][ ][Data][Cr]
Data 00 : Power Off 01 : *Power On
Ack [a][ ][Set ID][ ][OK/NG][Data][x]
►To Show TV is Power On or *Off
Transmission [k][a][ ][Set ID][ ][FF][Cr]
Ack [a][ ][Set ID][ ][OK][Data][x]
* Similarly, if other functions transmit ‘FF’ data
based on this format, Acknowledgement feedback
presents status about each function.
02. Aspect Ratio (Command: k c)
(Main Picture Size)
►To adjust the screen format. (Main picture format)
You can also adjust the screen format using the
Aspect Ratio in the Q.MENU. or PICTURE menu.
Transmission [k][c][ ][Set ID][ ][Data][Cr]
Data 01 : Normal screen
(4:3)
02 : Wide screen
(16:9)
04 : Zoom
05 : Zoom 2
(Latin America
except Colombia
Only)
06 : Set by Program/
Original
07 : 14:9
(Europe, Colombia, Mid-East,
Asia except South Korea and
Japan)
09 : * Just Scan
0B : Full Wide
(Europe, Colombia, Mid-
East, Asia except South
Korea and Japan)
10 to 1F : Cinema Zoom 1 to 16
0c : 21:9 (Depending on model)
Ack [c][ ][Set ID][ ][OK/NG][Data][x]
* Using the PC input, you select either 16:9 or 4:3
screen aspect ratio.
* In DTV/HDMI/Component mode (high-definition),
Just Scan is available.
* Full wide mode may work differently based on
model and is supported for DTV fully, and ATV,
AV partially.
03. Screen Mute (Command: k d)
►To select screen mute on/off.
Transmission [k][d][ ][Set ID][ ][Data][Cr]
Data 00 : Screen mute off (Picture on)
Video mute off
01 : Screen mute on (Picture off)
10 : Video mute on
Ack [d][ ][Set ID][ ][OK/NG][Data][x]
* In case of video mute on only, TV will display On
Screen Display(OSD). But, in case of Screen mute
on, TV will not display OSD.
04. Volume Mute (Command: k e)
►To control volume mute on/off.
You can also adjust mute using the MUTE button
on remote control.
Transmission [k][e][ ][Set ID][ ][Data][Cr]
Data 00 : Volume mute on (Volume off)
01 : Volume mute off (Volume on)
Ack [e][ ][Set ID][ ][OK/NG][Data][x]
05. Volume Control (Command: k f)
►To adjust volume.
You can also adjust volume with the volume
buttons on remote control.
Transmission [k][f][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Ack [f][ ][Set ID][ ][OK/NG][Data][x]
06. Contrast (Command: k g)
►To adjust screen contrast.
You can also adjust contrast in the PICTURE
menu.
Transmission [k][g][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Ack [g][ ][Set ID][ ][OK/NG][Data][x]
07. Brightness (Command: k h)
►To adjust screen brightness.
You can also adjust brightness in the PICTURE
menu.
Transmission [k][h][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Ack [h][ ][Set ID][ ][OK/NG][Data][x]
08. Color/Colour (Command: k i)
►To adjust the screen Color(Colour).
You can also adjust colour in the PICTURE menu.
Transmission [k][i][ ][Set ID][ ][Data][Cr]
8
ENG
ENGLISH
8EXTERNAL CONTROL DEVICE SETUP
Data Min : 00 to Max : 64
Ack [i][ ][Set ID][ ][OK/NG][Data][x]
09. Tint (Command: k j)
►To adjust the screen tint.
You can also adjust tint in the PICTURE menu.
Transmission [k][j][ ][Set ID][ ][Data][Cr]
Data Red : 00 to Green : 64
Ack [j][ ][Set ID][ ][OK/NG][Data][x]
10. Sharpness (Command: k k)
►To adjust the screen sharpness.
You can also adjust sharpness in the PICTURE
menu.
Transmission [k][k][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 32
Ack [k][ ][Set ID][ ][OK/NG][Data][x]
11. OSD Select (Command: k l)
►To select OSD (On Screen Display) on/off when
controlling remotely.
Transmission [k][l][ ][Set ID][ ][Data][Cr]
Data 00 : OSD off 01 : OSD on
Ack [l][ ][Set ID][ ][OK/NG][Data][x]
12. Remote control lock mode (Command: k m)
►To lock the front panel controls on the monitor and
remote control.
Transmission [k][m][ ][Set ID][ ][Data][Cr]
Data 00 : Lock off 01 : Lock on
Ack [m][ ][Set ID][ ][OK/NG][Data][x]
* If you are not using the remote control, use this
mode.
When main power is off & on (plug-off and plug-in,
after 20 - 30 seconds), external control lock is
released.
* In the standby mode (DC off by off timer or ‘ka’,
‘mc’ command), and if key lock is on, TV will not
turn on by power on key of IR & Local Key.
13. Treble (Command: k r)
►To adjust treble.
You can also adjust in the AUDIO menu.
Transmission [k][r][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Ack [r][ ][Set ID][ ][OK/NG][Data][x]
* (Depending on model)
14. Bass (Command: k s)
►To adjust Bass.
You can also adjust in the AUDIO menu.
Transmission [k][s][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Ack [s][ ][Set ID][ ][OK/NG][Data][x]
* (Depending on model)
15. Balance (Command: k t)
►To adjust balance.
You can also adjust balance in the AUDIO menu.
Transmission [k][t][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Ack [t][ ][Set ID][ ][OK/NG][Data][x]
16. Color(Colour) Temperature (Command: x u)
►To adjust colour temperature. You can also adjust
Color(Colour) Temperature in the PICTURE menu.
Transmission [x][u][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Ack [u][ ][Set ID][ ][OK/NG][Data][x]
17. ISM Method (Command: j p) (Only Plasma TV)
►To control the ISM method. You can also adjust
ISM Method in OPTION menu.
Transmission [j][p][ ][Set ID][ ][Data][Cr]
Data Min : 02: Orbiter
08: Normal
20: Color(Colour) Wash
Ack [p][ ][Set ID][ ][OK/NG][Data][x]
18. Equalizer (Command : j v)
►Adjust EQ of the set.
Transmission [j][v][ ][Set ID][ ][Data][Cr]
0 0 0 0 0 0 0 0
MSB
Frequency Data
LSB
9
ENGENGLISH
9
EXTERNAL CONTROL DEVICE SETUP
7 6 5 Frequency 4 3 2 1 0 Step
0 0 0 1st Band 0 0 0 0 0 0(decimal)
0 0 1 2nd Band 0 0 0 0 1 1(decimal)
0 1 0 3rd Band ... ... ... ... ... ...
0 1 1 4th Band 1 0 0 1 1 19(decimal)
1 0 0 5th Band 1 0 1 0 1 20(decimal)
Acknowledgement [v][ ][Set ID][ ][OK/NG][Data][x]
* It depends on model, and can adjust when sound
mode is EQ adjustable value.
19. Energy Saving (Command: j q)
►To reduce the power consumption of the TV. You
can also adjust Energy Saving in PICTURE menu.
Transmission [j][q][ ][Set ID][ ][Data][Cr]
Data
00 : Off
01 : Minimum
02 : Medium
03 : Maximum
04 : Auto (For LCD TV / LED TV) /
Intelligent sensor (For PDP TV)
05 : Screen off
* (Depending on model)
Ack [q][ ][Set ID][ ][OK/NG][Data][x]
20. Tune Command (Command: m a)
* This command may work differently depending on
model and signal.
• For Europe, Mid-East, Colombia, Asia except
South Korea and Japan Model
►Select channel to following physical number.
Transmission [m][a][ ][Set ID][ ][Data 00][ ]
[Data 01][ ][Data 02][Cr]
* Analog Antenna/Cable
[Data 00][Data 01] Channel Data
Data 00 : High byte channel data
Data 01 : Low byte channel data
- 00 00 ~ 00 C7 (Decimal : 0 ~ 199)
Data 02 : Input Source (Analog)
- 00 : Antenna TV (ATV)
- 80 : Cable TV (CATV)
* Digital Antenna/Cable/Satellite
[Data 00][Data 01]: Channel Data
Data 00 : High Channel data
Data 01 : Low Channel data
- 00 00 ~ 27 0F (Decimal: 0 ~ 9999)
Data 02 : Input Source (Digital)
- 10 : Antenna TV (DTV)
- 20 : Antenna Radio (Radio)
- 40 : Satellite TV (SDTV)
- 50 : Satellite Radio (S-Radio)
- 90 : Cable TV (CADTV)
- a0 : Cable Radio (CA-Radio)
* Tune Command Examples:
1. Tune to the Analog antenna (PAL) Channel 10.
Set ID = All = 00
Data 00 & 01 = Channel Data is 10 = 00 0a
Data 02 = Analog Antenna TV = 00
Result = ma 00 00 0a 00
2. Tune to the digital antenna (DVB-T) Channel 01.
Set ID = All = 00
Data 00 & 01 = Channel Data is 1 = 00 01
Data 02 = Digital Antenna TV = 10
Result = ma 00 00 01 10
3. Tune to the satellite (DVB-S) Channel 1000.
Set ID = All = 00
Data 00 & 01 = Channel Data is 1000 = 03 E8
Data 02 = Digital Satellite TV = 40
Result = ma 00 03 E8 40
Ack [a][ ][Set ID][ ][OK][Data 00][Data 01]
[Data 02][x][a][ ][Set ID][ ][NG][Data 00][x]
• For South Korea, North/Latin America except
Colombia Model
►To tune channel to following physical/major/minor
number.
Transmission [m][a][ ][0][ ][Data00][ ][Data01]
[ ][Data02][ ][Data03][ ][Data04][ ][Data05][Cr]
Digital channels have a Physical, Major, and Minor
channel number. The Physical number is the actual
digital channel number, the Major is the number that
the channel should be mapped to, and the Minor is
the sub-channel. Since the ATSC tuner automatically
maps the channel from the Major / Minor number,
the Physical number is not required when sending a
command in Digital.
* Analog Antenna/Cable
Data 00 : Physical Channel Number
- Antenna (ATV) : 02~45 (Decimal: 2 ~ 69)
- Cable (CATV) : 01, 0E~7D (Decimal : 1, 14~125)
[Data 01 ~ 04]: Major/Minor Channel Number
Data 01 & 02: xx (Don't care)
Data 03 & 04: xx (Don't care)
Data 05: Input Source (Analog)
- 00 : Antenna TV (ATV)
- 01 : Cable TV (CATV)
10
ENG
ENGLISH
10 EXTERNAL CONTROL DEVICE SETUP
* Digital Antenna/Cable
Data 00 : xx (Don't care)
[Data 01][Data 02]: Major Channel Number
Data 01 : High byte Channel Data
Data 02 : Low byte Channel Data
- 00 01 ~ 27 0F (Decimal: 1 ~ 9999)
[Data 03][Data 04]: Minor Channel Number
Data 03 : High byte Channel Data
Data 04 : Low byte Channel Data
Data 05 : Input Source (Digital)
- 02 : Antenna TV (DTV) – Use Physical Channel
Number
- 06 : Cable TV (CADTV) – Use Physical Channel
Number
- 22 : Antenna TV (DTV) – Don’t Use Physical
Channel Number
- 26 : Cable TV (CADTV) - Don’t Use Physical
Channel Number
- 46 : Cable TV (CADTV) – Use Physical/Major
Channel Number Only (One Part Channel)
- 66 : Cable TV (CADTV) – Use Major Channel
Number Only (One Part Channel)
Two bytes are available for each major and minor
channel data, but usually the low byte is used alone
(high byte is 0).
* Tune Command Examples:
1. Tune to the Analog cable (NTSC) channel 35.
Set ID = All = 00
Data 00 = Channel Data is 35 = 23
Data 01 & 02 = No Major = 00 00
Data 03 & 04 = No Minor = 00 00
Data 05 = Analog Cable TV = 01
Total = ma 00 23 00 00 00 00 01
2. Tune to the digital antenna (ATSC) channel 30-3.
Set ID = All = 00
Data 00 = Don’t know Physical = 00
Data 01 & 02 = Major is 30 = 00 1E
Data 03 & 04 = Minor is 3 = 00 03
Data 05 = Digital Antenna TV = 22
Total = ma 00 00 00 1E 00 03 22
Ack [a][ ][Set ID][ ][OK][Data 00][Data 01]
[Data 02][Data 03][Data 04][Data 05]
[x][a][ ][Set ID][ ][NG][Data 00][x]
• For Japan Model
►To tune channel to following physical/major/minor
number.
Transmission [m][a][ ][0][ ][Data00][ ][Data01]
[ ][Data02][ ][Data03][ ][Data04][ ][Data05][Cr]
* Digital Antenna/Satellite
Data 00: xx (Don't care)
[Data 01][Data 02]: Major Channel Number
Data 01: High byte Channel Data
Data 02: Low byte Channel Data
- 00 01 ~ 27 0F (Decimal: 1 ~ 9999)
[Data 03][Data 04]: Minor/Branch Channel Number
(Don’t care in Satellite)
Data 03: High byte Channel Data
Data 04: Low byte Channel Data
Data 05 : Input Source (Digital/Satellite for Japan)
- 02 : Antenna TV (DTV)
- 07 : BS (Broadcasting Satellite)
- 08 : CS1 (Communication Satellite 1)
- 09 : CS2 (Communication Satellite 2)
* Tune Command Examples:
1
Tune to the digital antenna (ISDB-T) channel 17-1
.
Set ID = All = 00
Data 00 = Don’t know Physical = 00
Data 01 & 02 = Major is 17 = 00 11
Data 03 & 04 = Minor/Branch is 1 = 00 01
Data 05 = Digital Antenna TV = 02
Total = ma 00 00 00 11 00 01 02
2. Tune to the BS (ISDB-BS) channel 30.
Set ID = All = 00
Data 00 = Don’t know Physical = 00
Data 01 & 02 = Major is 30 = 00 1E
Data 03 & 04 = Don’t Care = 00 00
Data 05 = Digital BS TV = 07
Total = ma 00 00 00 1E 00 00 07
* This feature is varied based on the model.
Ack [a][ ][Set ID][ ][OK][Data 00][Data 01]
[Data 02][Data 03][Data 04][Data 05]
[x][a][ ][Set ID][ ][NG][Data 00][x]
21. Channel(Programme) Add/Del(Skip)
(Command: m b)
►To skip current channel(programme) for next time.
Transmission [m][b][ ][Set ID][ ][Data][Cr]
Data 00 : Del(ATSC,ISDB)/Skip(DVB) 01 : Add
Ack [b][ ][Set ID][ ][OK/NG][Data][x]
* Set the saved channel status to del(ATSC, ISDB)/
skip(DVB) or add.
11
ENGENGLISH
11
EXTERNAL CONTROL DEVICE SETUP
22. Key (Command: m c)
►To send IR remote key code.
Transmission [m][c][ ][Set ID][ ][Data][Cr]
Data Key code - p.2.
Ack [c][ ][Set ID][ ][OK/NG][Data][x]
23. Control Backlight (Command: m g)
• For LCD TV / LED TV
►To control the backlight.
Transmission [m][g][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Ack [g][ ][Set ID][ ][OK/NG][Data][x]
Control Panel Light (Command: m g)
• For Plasma TV
►To control the panel light.
Transmission [m][g][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Ack [g][ ][Set ID][ ][OK/NG][Data][x]
24. Input select (Command: x b)
(Main Picture Input)
►To select input source for main picture.
Transmission [x][b][ ][Set ID][ ][Data][Cr]
Data
00 : DTV
02 : Satellite DTV
ISDB-BS (Japan)
03 : ISDB-CS1 (Japan)
04 : ISDB-CS2 (Japan)
11 : CATV
01 : CADTV
10 : ATV
20 : AV or AV1 21 : AV2
40 : Component1
60 : RGB
41 : Component2
90 : HDMI1
92 : HDMI3
91 : HDMI2
93 : HDMI4
Ack [b][ ][Set ID][ ][OK/NG][Data][x]
* This function depends on model and signal.
25. 3D(Command: x t) (only 3D models)
(Depending on model)
►To change 3D mode for TV.
Transmission [x][t][ ][Set ID][ ][Data 00][ ][Data 01]
[ ][Data 02][ ][Data 03][Cr]
* (Depending on model)
Data Structure
[Data 00] 00 : 3D On
01 : 3D Off
02 : 3D to 2D
03 : 2D to 3D
[Data 01] 00 : Top and Bottom
01 : Side by Side
02 : Check Board
03 : Frame Sequential
04 : Column interleaving
05 : Row interleaving
[Data 02] 00 : Right to Left
01 : Left to Right
[Data 03] 3D Effect(3D Depth): Min : 00 - Max : 14
(*transmit by Hexadecimal code)
* [Data 02], [Data 03] functions depend on model
and signal.
* If [Data 00] is 00 (3D On), [Data 03] has no
meaning.
* If [Data 00] is 01 (3D off) or 02 (3D to 2D), [Data
01], [Data 02] and [Data 03] have no meaning.
* If [Data 00] is 03 (2D to 3D), [Data 01] and
[Data 02] have no meaning.
* If [Data 00] is 00 (3D On) or 03 (2D to 3D), [Data
03] works when 3D Mode (Genre) is manual only.
* All 3D pattern options ([Data 01]) may not be
available according to broadcasting/video signal.
[Data 00] [Data 01] [Data 02] [Data 03]
00 O O O
01 X X X
02 X X X
03 X O O
X : don’t care
Ack [t][ ][Set ID][ ][OK][Data00][Data01][Data02]
[Data03][x]
[t][ ][Set ID][ ][NG][Data00][x]
12
ENG
ENGLISH
12 EXTERNAL CONTROL DEVICE SETUP
26. Extended 3D(Command: x v) (only 3D models)
(Depending on model)
►To change 3D option for TV.
Transmission [x][v][ ][Set ID][ ][Data 00][ ]
[Data 01][Cr]
[Data 00] 3D option
00 : 3D Picture Correction
01 : 3D Depth (3D Mode is Manual Only)
02 : 3D Viewpoint
06 : 3D Color Correction
07 : 3D Sound Zooming
08 : Normal Image View
09 : 3D Mode (Genre)
[Data 01] It has own range for each 3D option
determined by [Data 00].
1) When [Data 00] is 00
00 : Right to Left
01 : Left to Right
2) When [Data 00] is 01, 02
Data Min: 0 - Max: 14 (*transmit by Hexadecimal
code)
Data value range(0 - 20) converts Viewpoint range
(-10 - +10) automatically (Depending on model)
* This option works when 3D Mode (Genre) is manual
only.
3) When [Data 00] is 06, 07
00 : Off
01 : On
4) When [Data 00] is 08
00 : Revert to 3D video from 3D-to-2D
converted 2D video
01 : Change 3D video to 2D video, except
2D-to-3D video
* If conversion condition doesn’t meet, command is
treated as NG.
5) When [Data 00] is 09
00 : Standard
02 : Cinema
04 : Manual
01 : Sport
03 : Extreme
05 : Auto
Ack [v][ ][Set ID][ ][OK][Data00][Data01][x]
[v][ ][Set ID][ ][NG][Data00][x]
27. Auto Configure (Command: j u)
(Depending on model)
►To adjust picture position and minimize image
shaking automatically. It works only in RGB (PC)
mode.
Transmission [j][u][ ][Set ID][ ][Data][Cr]
Data 01 : To set Auto Configure
Ack [u][ ][Set ID][ ][OK/NG][Data][x]
13
ENGENGLISH
13
EXTERNAL CONTROL DEVICE SETUP
Network IP Control
(For USA only)
How to connect
1. Connect your TV to a wired or wireless network.
2. Press and hold the (Settings) button on the remote control for at least 5 seconds on the Live TV
screen. Once the Live TV channel banner appears at the top of the screen, enter 828 and press the OK
button to enter the ‘IP Control Setup’ menu.
* The 3-digit password (default password: 828) can be changed using Password Change.
3. After entering the ‘IP Control Setup’ menu, set the ‘Network IP Control’ submenu to ‘On’. The reboot
popup window will appear. Select ‘Yes’ to reboot your TV.
* Set to 'Off' when the feature is not in use.
4. Open a terminal program (e.g. putty, teraterm) on a computer and connect to your TV with your TV’s IP
address through telnet service and the port number 9761 as shown below.
ex) username : ~$ telnet 10.186.119.107 9761
5. If the connection is successful, the following message will appear. Or if ‘NG’ appears when you press
Enter, the connection has been established.
Trying 10.186.119.107...
Connected to 10.186.119.107.
Escape character is ' ^ ] ' .
6. Enter a command like the example shown below and press Enter.
VOLUME_MUTE on
7. If the command has been successfully entered, ‘OK’ will appear. If not, ‘NG’ will appear.
8. To exit the program, enter ‘quit’ and press Enter. Then, the following message will appear.
quit
Connection closed by foreign host
* Power ON through WOL(Wake On Lan)
You can turn on the TV, after setting the ‘Mobile TV On’ submenu(Setting > General > Mobile TV On) to
‘On’ and installing the app related with WOL(Wake On Lan) through iOS or Google Play on your mobile
phone.
14
ENG
ENGLISH
14 EXTERNAL CONTROL DEVICE SETUP
Command reference list
COMMAND NOTE
01. Power POWER off ex) POWER off
02. Aspect Ratio ASPECT_RATIO [4by3 /16by9 /
setbyoriginal] ex) ASPECT_RATIO 4by3
03. Screen Mute SCREEN_MUTE [screenmuteon /
videomuteon / allmuteoff] ex) SCREEN_MUTE screenmuteon
04. Volume Mute VOLUME_MUTE [on / off] ex) VOLUME_MUTE on
05. Volume Control VOLUME_CONTROL [0 to 100] 0 to 100
(Decimal)
ex) VOLUME_CONTROL 15
06. Contrast PICTURE_CONTRAST [0 to 100] 0 to 100
(Decimal)
ex) PICTURE_CONTRAST 50
07. Brightness PICTURE_BRIGHTNESS [0 to 100] 0 to 100
(Decimal)
ex) PICTURE_BRIGHTNESS 50
08. Color/Colour PICTURE_COLOUR [0 to 100] 0 to 100
(Decimal)
ex) PICTURE_COLOUR 50
09. Tint PICTURE_TINT [0 to 100] 0 to 100
(Decimal)
ex) PICTURE_TINT 50
10. Sharpness PICTURE_SHARPNESS [0 to 50] 0 to 50
(Decimal)
ex) PICTURE_SHARPNESS 25
11. OSD Select OSD_SELECT [on / off] ex) OSD_SELECT on
12. Remote Control
Lock Mode REMOTECONTROLER_LOCK [on / off] ex) REMOTECONTROLER_LOCK on
13. Balance AUDIO_BALANCE [0 to 100] 0 to 100
(Decimal)
ex) AUDIO_BALANCE 50
14. Color(Colour)
Temperature
PICTURE_COLOUR_TEMPERATURE
[0 to 100]
0 to 100
(Decimal)
ex) PICTURE_COLOUR_TEMPERATURE 50
15. Equalizer AUDIO_EQUALIZER [1 to 5] [0 to 20]
1 to 5(Frequency band)
0 to 20(Step decimal)
* Precondition : All settings > sound > sound
mode settings > Equalizer on
ex) AUDIO_EQUALIZER 2 10
16. Energy Saving ENERGY_SAVING [screenoff / maximum
/ medium / minimum / off] ex) ENERGY_SAVING screenoff
17. Tune Command
CHANNEL_SETTING_ATSC_ATV
[Channel Number] antenna
CHANNEL_SETTING_ATSC_ATV
[Channel Number] cable
CHANNEL_SETTING_ATSC_DTV
[Channel Number] cablemaj
ex) CHANNEL_SETTING_ATSC_ATV 11
antenna
CHANNEL_SETTING_ATSC_DTV [Maj.
Channel Number] [Min.Channel Number]
antennanotphy
CHANNEL_SETTING_ATSC_DTV [Maj.
Channel Number] [Min.Channel Number]
cablenotphy
ex) CHANNEL_SETTING_ATSC_DTV 10 2
antennanotphy
18.
Channel(Programme)
Add/Del
CHANNEL_ADD_DELETE [add / delete] ex) CHANNEL_ADD_DELETE add
15
ENGENGLISH
15
EXTERNAL CONTROL DEVICE SETUP
COMMAND NOTE
19. Key
KEY_ACTION [exit / channelup /
channeldown / volumeup / volumedown /
arrowright / arrowleft / volumemute
/ deviceinput / sleepreserve / livetv
/ previouschannel / favoritechannel /
teletext / teletextoption / returnback
/ avmode / captionsubtitle / arrowup /
arrowdown / myapp / settingmenu / ok /
quickmenu / videomode
/ audiomode / channellist / bluebutton /
yellowbutton / greenbutton / redbutton /
aspectratio / audiodescription
/ programmorder / userguide /
smarthome / simplelink / fastforward /
rewind / programminfo / programguide
/ play / slowplay / soccerscreen / record /
3d / autoconfig / app / screenbright
/ number0 / number1 / number2 /
number3 / number4 / number5 / number6
/ number7 / number8 / number9]
ex) KEY_ACTION ok
20. Control Backlight PICTURE_BACKLIGHT [0 to 100]
0 to 100 (Decimal)
* Precondition : All settings > picture > Energy
Saving off
ex) PICTURE_BACKLIGHT 50
21. Input select
INPUT_SELECT [dtv / atv / cadtv / catv
/ avav1 / component1 / hdmi1 / hdmi2 /
hdmi3]
ex) INPUT_SELECT dtv
22. 3D (only 3D
models)
PICTURE_3D [off / 3dto2d] ex) PICTURE_3D off
PICTURE_3D 2dto3d [righttoleft /
lefttoright] [0 to 20] ex) PICTURE_3D 2dto3d righttoleft 10
PICTURE_3D on [topandbottom
/ sidebyside / checkboard /
framesequential / columninterleaving /
rowinterleaving] [righttoleft / lefttoright] [0
to 20]
ex) PICTURE_3D on topandbottom righttoleft
0
16
ENG
ENGLISH
16 EXTERNAL CONTROL DEVICE SETUP
COMMAND NOTE
23. Extended 3D (only
3D models)
PICTURE_3D_EXTENSION
picturecorrection [0 / 1]
0 : Right to Left
1 : Left to Right
* Precondition :
1) PICTURE_3D on X X X
ex) PICTURE_3D_EXTENSION
picturecorrection 0
PICTURE_3D_EXTENSION
[colorcorrection / sound] [0 / 1]
0 : off
1 : on
* Colorcorrection, Sound Precondition :
1) PICTURE_3D on X X X
Colorcorrection ex)
PICTURE_3D on topandbottom righttoleft 0
PICTURE_3D_EXTENSION colorcorrection 1
Sound ex)
PICTURE_3D on topandbottom righttoleft 0
PICTURE_3D_EXTENSION sound 1
PICTURE_3D_EXTENSION normal [0
/ 1]
0 : off
1 : on
* Precondition :
1) PICTURE_3D on X X X
ex) PICTURE_3D_EXTENSION normal 0
PICTURE_3D_EXTENSION
[depth / viewpoint] [0 to 20]
0 to 20 : Viewpoint range
* Depth precondition :
1) PICTURE_3D 2dto3d X X
2) PICTURE_3D_EXTENSION genre 4
* Viewpoint precondition :
1) PICTURE_3D 2dto3d X X
Depth ex)
PICTURE_3D 2dto3d righttoleft 0
PICTURE_3D_EXTENSION genre 4
PICTURE_3D_EXTENSION depth 0
Viewpoint ex)
PICTURE_3D 2dto3d righttoleft 0
PICTURE_3D_EXTENSION viewpoint 0
PICTURE_3D_EXTENSION genre [0 to
5]
0 : Standard / 1 : Sport / 2 : Cinema / 3 :
Extreme / 4 : Manual / 5 : Auto
* Precondition :
1) PICTURE_3D 2dto3d X X
ex) PICTURE_3D_EXTENSION genre 2
* This feature is varied based on the model.
* During playing or recording media, all commands except Power and Key commands are not executed and
treated as NG.
P/No: MFL69289458 (1607-REV05)
LED TV
43UH6100
49UH6100
55UH6150
60UH6150
65UH6150
49UH610A
55UH615A
60UH615A
65UH615A
49UH6090
55UH6090
60UH6090
43UH610A
43UH6030
49UH6030
55UH6030
60UH6030
65UH6030
60UH6035
www.lg.com
AAA
60UH6035
55/60/65UH6030
55/60/65UH615A
55/60/65UH6150
43/49UH610A,
49UH6090, 43/49UH6030
43/49UH6100 55/60UH6090
X 4
(M4 X L14)
ENGLISH Depending upon model
ESPAÑOL Según el modelo
FRANÇAIS Selon le modèle
ENGLISH
Easy Setup Guide
Please read this manual carefully before operating your set and retain it for future
reference.
ESPAÑOL
Guía Rápida de Configuración
Lea atentamente este manual antes de poner en marcha el equipo y consérvelo para
futuras consultas.
FRANÇAIS
Guide de configuration rapide
Avant d’utiliser l’appareil, veuillez lire attentivement ce guide et conservez-le pour
pouvoir vous y reporter ultérieurement.
3 4
21
1
2
1
2
1
2
43/49UH6100, 43/49UH610A, 49UH6090, 43/49UH6030
ENGLISH Read Safety and Reference.
ESPAÑOL Leer Seguridad y Consultas.
FRANÇAIS Lisez Sécurité et références.
2 3 4
5 6
1
55/60/65UH6150, 55/60/65UH615A, 55/60/65UH6030, 60UH6035
2 31
55/60UH6090
VIDEO/Y PBPRL/MONO AUDIO R
COMPONENT IN AV INAV IN
VIDEO L/MONO AUDIO R
VIDEO L/MONO AUDIO RVIDEO L/MONO AUDIO R
VIDEO AUDIO
VIDEO/Y PBPRL/MONO AUDIO R
HDMI IN 2/ARC
HDMI IN1
USB IN
HP OUT
ANTENNA
CABLE IN
12
4
3
or
ou
o
12
0
ENGLISH
MODELS
43UH6100
(43UH6100-UH)
49UH6100
(49UH6100-UH) 55UH6150
(55UH6150-UB)
49UH610A
(49UH610A-UJ)
43UH610A
(43UH610A-UJ)
55UH615A
(55UH615A-UC)
49UH6090
(49UH6090-UJ)
43UH6030
(43UH6030-UB) 55UH6030
(55UH6030-UC)
49UH6030
(49UH6030-UB)
43UH6030
(43UH6030-UD)
49UH6030
(49UH6030-UD)
Dimensions
(W x H x D)
With stand 976 x 633 x 217.9 (mm)
38.4 x 24.9 x 8.5 (inches)
1,108 x 707 x 217.9 (mm)
43.6 x 27.8 x 8.5 (inches)
1,240 x 778 x 237 (mm)
48.8 x 30.6 x 9.3 (inches)
Without stand 976 x 583 x 81.5 (mm)
38.4 x 22.9 x 3.2 (inches)
1,108 x 657 x 81.5 (mm)
43.6 x 25.8 x 3.2 (inches)
1,240 x 722 x 56.7 (mm)
48.8 x 28.4 x 2.2 (inches)
Weight With stand 9.0 kg (19.8 lbs) 12.0 kg (26.4 lbs) 18.1 kg (39.9 lbs)
Without stand 8.7 kg (19.1 lbs) 11.7 kg (25.7 lbs) 17.8 kg (39.2 lbs)
Power requirement AC 100 - 240 V ~ 50 / 60 Hz
Current value /
Power consumption 1.0 A / 100 W 1.1 A / 110 W 1.3 A / 130 W
12
0
ENGLISH
MODELS
60UH6150
(60UH6150-UB) 65UH6150
(65UH6150-UB)
55UH6090
(55UH6090-UF)
60UH6090
(60UH6090-UF)
60UH615A
(60UH615A-UC) 65UH615A
(65UH615A-UC)
60UH6030
(60UH6030-UC) 65UH6030
(65UH6030-UC)
60UH6035
(60UH6035-UC)
Dimensions
(W x H x D)
With stand 1,348 x 839 x 263 (mm)
53.0 x 33.0 x 10.3 (inches)
1,460 x 902 x 263 (mm)
57.4 x 35.5 x 10.3 (inches)
1,240 x 785 x 231 (mm)
48.8 x 30.9 x 9.0 (inches)
1,348 x 844 x 258 (mm)
53.0 x 33.2 x 10.1 (inches)
Without stand 1,348 x 782 x 58.5 (mm)
53.0 x 30.7 x 2.3 (inches)
1,460 x 846 x 58.5 (mm)
57.4 x 33.3 x 2.3 (inches)
1,240 x 722 x 56.7 (mm)
48.8 x 28.4 x 2.2 (inches)
1,348 x 782 x 58.5 (mm)
53.0 x 30.7 x 2.3 (inches)
Weight With stand 23.7 kg (52.2 lbs) 27.4 kg (60.4 lbs) 18.2 kg (40.1 lbs) 23.8 kg (52.4 lbs)
Without stand 23.3 kg (51.3 lbs) 27.0 kg (59.5 lbs) 17.8 kg (39.2 lbs) 23.3 kg (51.3 lbs)
Power requirement AC 100 - 240 V ~ 50 / 60 Hz
Current value /
Power consumption 1.4 A / 140 W 1.5 A / 150 W 1.3 A / 130 W 1.4 A / 140 W
ESPAÑOL
FRANÇAIS
MODELOS
43UH6100
(43UH6100-UH)
49UH6100
(49UH6100-UH) 55UH6150
(55UH6150-UB)
49UH610A
(49UH610A-UJ)
43UH610A
(43UH610A-UJ)
55UH615A
(55UH615A-UC)
49UH6090
(49UH6090-UJ)
MODÈLES
43UH6030
(43UH6030-UB) 55UH6030
(55UH6030-UC)
49UH6030
(49UH6030-UB)
43UH6030
(43UH6030-UD)
49UH6030
(49UH6030-UD)
Dimensiones
(Ancho x altura
x profundidad)
Con base 976 x 633 x 217,9 (mm)
38,4 x 24,9 x 8,5
(pulgadas / pouces)
1 108 x 707 x 217,9 (mm)
43,6 x 27,8 x 8,5
(pulgadas / pouces)
1 240 x 778 x 237 (mm)
48,8 x 30,6 x 9,3
(pulgadas / pouces)
Avec support
Dimensions
(L x H x P)
Sin base 976 x 583 x 81,5 (mm)
38,4 x 22,9 x 3,2
(pulgadas / pouces)
1 108 x 657 x 81,5 (mm)
43,6 x 25,8 x 3,2
(pulgadas / pouces)
1 240 x 722 x 56,7 (mm)
48,8 x 28,4 x 2,2
(pulgadas / pouces)
Sans support
Peso Con base 9,0 kg (19,8 libras / lb) 12,0 kg (26,4 libras / lb) 18,1 kg (39,9 libras / lb)
Avec support
Poids Sin base 8,7 kg (19,1 libras / lb) 11,7 kg (25,7 libras / lb) 17,8 kg (39,2 libras / lb)
Sans support
Alimentación requerida AC 100 - 240 V ~ 50 / 60 Hz
Alimentation
Corriente de consumo /
Consumo de potencia 1,0 A / 100 W 1,1 A / 110 W 1,3 A / 130 W
Valeur courante /
Consommation électrique
12
0
ESPAÑOL
FRANÇAIS
MODELOS
MODÈLES
60UH6150
(60UH6150-UB) 65UH6150
(65UH6150-UB)
55UH6090
(55UH6090-UF)
60UH6090
(60UH6090-UF)
60UH615A
(60UH615A-UC) 65UH615A
(65UH615A-UC)
60UH6030
(60UH6030-UC) 65UH6030
(65UH6030-UC)
60UH6035
(60UH6035-UC)
Dimensiones
(Ancho x altura x
profundidad)
Con base 1 348 x 839 x 263 (mm)
53,0 x 33,0 x 10,3
(pulgadas / pouces)
1 460 x 902 x 263 (mm)
57,4 x 35,5 x 10,3
(pulgadas / pouces)
1 240 x 785 x 231 (mm)
48,8 x 30,9 x 9,0
(pulgadas / pouces)
1 348 x 844 x 258 (mm)
53,0 x 33,2 x 10,1
(pulgadas / pouces)
Avec support
Dimensions
(L x H x P)
Sin base 1 348 x 782 x 58,5 (mm)
53,0 x 30,7 x 2,3
(pulgadas / pouces)
1 460 x 846 x 58,5 (mm)
57,4 x 33,3 x 2,3
(pulgadas / pouces)
1 240 x 722 x 56,7 (mm)
48,8 x 28,4 x 2,2
(pulgadas / pouces)
1 348 x 782 x 58,5 (mm)
53,0 x 30,7 x 2,3
(pulgadas / pouces)
Sans support
Peso Con base 23,7 kg (52,2 libras / lb) 27,4 kg (60,4 libras / lb) 18,2 kg (40,1 libras / lb) 23,8 kg (52,4 libras / lb)
Avec support
Poids Sin base 23,3 kg (51,3 libras / lb) 27,0 kg (59,5 libras / lb) 17,8 kg (39,2 libras / lb) 23,3 kg (51,3 libras / lb)
Sans support
Alimentación requerida AC 100 - 240 V ~ 50 / 60 Hz
Alimentation
Corriente de consumo /
Consumo de potencia 1,4 A / 140 W 1,5 A / 150 W 1,3 A / 130 W 1,4 A / 140 W
Valeur courante /
Consommation électrique
12
0
*MFL69289458*
(For USA and Canada only)
(Para Estados Unidos y Canadá)
(Except for 43UH610A-UJ, 60UH6035-UC)
This product qualifies for ENERGY STAR®
in the factory default (Home configuration)
setting. Changing the factory default settings or enabling
other features may increase power consumption that
could exceed the limits necessary to quality for ENERGY
STAR®. Refer to ENERGYSTAR.gov for more information
on the ENERGY STAR® program.
(Pour les États-Unis et le Canada seulement)
(À l'exception du 43UH610A-UJ,
60UH6035-UC)
Ce produit est conforme aux normes ENERGY
STAR® lorsque le réglage d’usine par défaut
(Résidentiel) est sélectionné. Modifier les réglages
d’usine par défaut ou activer d’autres fonctionnalités
augmente la consommation d'énergie, qui pourrait alors
dépasser les limites de la qualification ENERGY STAR®.
Consultez le site ENERGYSTAR.gov pour en savoir plus au
sujet du programme ENERGY STAR®.