Table of Contents
LG 86UT640S0UA User Manual
Displayed below is the user manual for 86UT640S0UA by LG which is a product in the Hospitality TVs category. This manual has pages.
Related Manuals
INSTALLATION MANUAL
LED TV*
Please read this manual carefully before operating your set
and retain it for future reference.
UT64**
UT34**
UT66**
LT66** US34**
www.lg.com
Copyright © 2020 LG Electronics Inc. All Rights Reserved.
ENGLISH
2
Table of contents
3 Location and Function of Controls
3 Parts and Button
3 Basic functions
4 First Use Wizard
5 Basic Settings
5 - Language & Location
6 - Network Settings
7 - Portal Settings
8 - Voice Service Coverage
9 Data Cloning
9 Solution Settings
9 - Language & Location selection
10 - Automatically for Setup
14 - Manually for Setup
17 Installation Menu Settings
18 Installation Menu
18 Introduction
19 Public Display Settings
19 - Public Display Settings Operation
19 - Power On Status
20 - Volume
20 - Key Management
21 - Limited Mode
22 - DTV Channel Update
22 - Power On Default
22 - Aux Source Setting
22 - Power Management
22 - Factory Reset
23 Network
23 - MAC Address
23 - Network Setting
24 - LG Connect
24 - IP Stream Control
24 - Wake On LAN
24 - VLAN ID
24 - Server Settings
25 - Ping Test
26 Pro:Centric
26 - Mode
26 - Update Event
26 - Room Number Setting
26 - Media Type
27 - Receive Data
28 General
28 - Configuration Setup
31 - External Speaker
32 - Set ID Setup
32 - Power Saving
33 - HCEC Setup
34 - Clock Setup
34 - Password Change
34 - Lock Mode
35 - Welcome Video Mode
35 - Crestron
35 - Developer Mode
35 Portal Settings
35 - Portal Mode
36 - Auto Start
36 - PreLoaded App
36 - Website Shortcut
36 - Input Shortcut
36 - Hotel Directory
37 - Portal Editor
37 - Portal Manager
39 Media Share
39 - SmartShare
39 - Screen Share
39 - Media Renderer
39 - DIAL
39 - TV Name
39 - SoftAP
41 - Beacon
42 TV Manager
42 - Diagnostics
47 - USB Download Menu
52 CONTENT MANAGER
52 - Web Login
52 - Content Manager
56 - Group Manager 2.0
58 IR Codes
59 External control device Setup
59 RS-232C Setup
59 Phone jack Type
59 Type of Connector : D-Sub 9-Pin Male
60 RS-232C Configurations
60 Communication Parameters
60 IR OUT Using Guide
60 - Suitable / Not Recommend remote-controller data
format
60 - IR Receiver specifications
61 Command Reference List
61 Transmission / Receiving Protocol
ENGLISH
3
Location and Function of Controls
Parts and Button
Basic functions
Power On (Press)
Power O1 (Press and Hold)
Menu Control (Press2)
Menu Selection (Press and Hold3)
1 All running apps will close.
2 You can access and adjust the menu by pressing the button when TV is on.
3 You can use the function when you access menu control.
ENGLISH
4
First Use Wizard
* Image shown may differ from your TV.
(Depending on model)
•There are four options - Basic Settings, Data Cloning, Solution Settings, and Installation Menu Settings. Each menu can access by
START button.
ENGLISH
5
Basic Settings
* Image shown may differ from your TV.
This menu is for basic settings related to language, network, portal, voice service coverage and channel tuning without SI (Pro:Centric) setting. There
are four steps for it.
Language & Location
(Depending on model)
•Select the Language and Country. Some countries need to select the Time Zone.
ENGLISH
7
Portal Settings
(Depending on model)
•Set the Portal Mode and Portal Auto Start.
Portal Mode
(Depending on model)
•You can select ‘Default Portal’ (Use webOS default portal), ‘Customizable Portal’ (Use editable Portal), or ‘None’ (Do not use portal).
Portal Auto Start
•You can select ‘On’ or ‘O’. If you select ‘On’, Portal (Home Launcher) will be execute automatically after TV on.
ENGLISH
8
Voice Service Coverage
(Depending on model)
•Set the voice service coverage. You can set LG Service Country and Service Area Postcode for voice service.
ENGLISH
9
Data Cloning
(Depending on model)
Access Data cloning menu of TV Manager application for applying cloning le.
Solution Settings
(Depending on model)
The Pro:Centric Platform enables you to simply install, manage and use guest-centric solutions. The default Domain “procentric.local” and IP Server
Address are needed to be registered in DNS TV will contact the IP Server using the default Domain “procentric.local” via IP on server search page. If TV
doesn’t contact the Server, TV will search the pre-dened channel earlier than all channels.
Language & Location selection
(Depending on model)
•Please select the Language and Country. Some countries need to select the Time Zone.
ENGLISH
10
Automatically for Setup
(Depending on model)
1 From the TV Conguration Options screen, you can choose how to proceed with the conguration of this TV. Whether you will congure the TV
for Pro:Centric operation via the wizard or use a USB memory device to congure the TV, you may rst wish to set the Room Number on the TV.
Also, you can congure the network environment.
•Complete initial download of maintenance(On/O Toggle): you can choose the option whether to skip the maintenance les download during
the EZ-Manager process.
•If you intend to set Room Number as part of the TV conguration, use the Room Number option to assign the Room # for this TV before you
continue with additional conguration.
•In the Label eld, use the Left/Right arrow keys to specify a North, South, East, or West designation for this TV.
•In the Room Number eld, you can use the number keys on the Installation Remote to direct enter a room number or use the virtual keyboard
on the TV screen.
ENGLISH
11
•If you intend to apply the les via USB, use USB Conguration option to access TV Manager app. (“TV Manager” on page 42)
•To continue, move and select NEXT.
•If you intend to set network, use the Network Settings option. You can connect easily to wired/wireless network by this option. (“Network
Settings” on page 6)
ENGLISH
12
2 This step automatically searches for the Pro:Centric Server. If was found the Pro:Centric data channel, select the NEXT.
ENGLISH
13
3 Downloading the Pro:Centric application les takes few minutes.
4 After the installation is completed, the following screen will be displayed.
ENGLISH
14
Manually for Setup
(Depending on model)
1 Select a Label and/or enter the Room Number using the numeric keypad on the remotes or using the virtual keyboard on the TV screen. To
continue, move and select NEXT.
2 Please select the MANUAL PRO:CENTRIC.
ENGLISH
15
3 Congure the appropriate Pro:Centric settings in the TV.
ENGLISH
16
4 Downloading the Pro:Centric application les takes few minutes.
ENGLISH
17
5 After the installation is completed, the following screen will be displayed.
Installation Menu Settings
Access Installation menu for commercial feature settings.
ENGLISH
18
Installation Menu
* Image shown may differ from your TV.
Introduction
The abundant functions for Hotel TV linked with software installation can be projected on OSD as ‘Installation Menu’.
The wide range of hotel features can be performed simply on additional window to enhance the LG hotel TV’s easy installation and convenient
operation for Hotelier and System Integrators.
1 Press the Setting button for more than 5 seconds using the user remote control, banner will appear at top left on the screen.
2 Enter a four digit password and press ‘OK’ button.
-The TV is set with the initial password “1-1-0-5”.
ENGLISH
19
Public Display Settings
-When ‘Public Display Mode’ is set to On, all functions of Public Display Mode apply.
Public Display Settings Operation
-Decide to work all functions of ‘Public Display Mode’ or not
-When ‘Public Display Mode’ is set to Off, all functions of Public Display Mode Do Not apply.
Power On Status
-Decide to select working status of TV Set when turn on main power.
-You can select PWR, STD, LST.
-PWR always make TV set On status when turn on main power .
-STD make Stand-by status when turn on main power.
-LST make TVSet work like previous power status. As same concept as Power Backup mode; If main power were turned off in Power On
status, TVSet would work in On status. If main power were turned off in Stand-by status, TVSet would work in Stand-by status.
-If there Block All is both IR Operation and Local Key Operation from Key Management, In order to provide the Option that must be able
to turn on the TV in the TV turned off situation, change the value of the PWR. (Reference the Key Management)
ENGLISH
20
Volume
-Decide to apply volume policy of ‘Start Volume’, ‘Maximum Volume’ and ‘Minimum Volume’ as On or Off.
-(0 ≤ Min ≤ Start ≤ Max ≤ 100)
Start Volume
•This entry sets the start volume level when is power on.
-The level is specified as a number between minimum volume to maximum value. (Min ≤ Start ≤ Max)
-The default setting is ‘Off’.
-When selected to 'On', if the value is lower then the minimum specified in the minimum volume entry, the minimum volume entry must
be used.
-When selected to 'On', if the value is larger then the maximum specified in the maximum volume entry, the maximum volume value
must be used.
-Access to a volume in ‘Timer Power On’ must be fixed to start volume when ‘Public Display Mode’ (On) and ‘Start Volume’ (Off, 0 ~ 100)
were set simultaneously.
Maximum Volume
•This entry sets the maximum volume level the set. The level is specied as a number between ‘Minimum Volume’ to 100. (Min ≤ Max ≤ 100).
-The default value is 100.
Minimum Volume
•This entry sets the minimum volume level the set. The level is specied as a number between 0 to ‘Maximum Volume’. (0 ≤ Min ≤ Max)
-The default value is 0.
Key Management
-Manage key usability of Local(Front) Key and Remote Control. When selected to ‘On’, following ‘IR Operation’ and ‘Local Key Operation’
will be worked by below.
IR Operation
•Decide whether work the LG remote control or not.
-When ‘IR Operation’ is set to ‘Normal’, all remote keys are available.
-‘Use PWR Only’ makes block all remote keys except power key.
-When ‘IR Operation’ is set to ‘Block All’, all normal remote keys don’t work.
Local Key Operation
•Decide to operate ‘Local Key’ working behavior.
-When ‘Local Key Operation’ is set to ‘Normal’, all local keys are available.
-‘Use PWR Only’ makes block all local keys except power key.
-When ‘Local Key Operation’ is set to ‘Block All’, all local keys don’t work.
ENGLISH
21
Limited Mode
-Configure TV function’s limitation. When selected to ‘On’, following sub-menus will be worked by below.
Setup Menu
-Permit to tune and manage Channels.
Channel Change
•Decide to change channel or not by setting ‘Channel Change’ as ‘On’(Change Possible) or ‘O’(Change Impossible) when present source is TV.
Menu Display
•Function to decide whether work with menu of control key or not.
-Although select Off, the action that press a Menu button for 5 seconds to enter ‘Installation Menu’ is available.
-When select On, Menu works.
OSD Display
•Decide to display OSD or not.
-When is set to ‘Off’, all OSD is not displayed except some exception.
-Although select ‘Off’, the action that press a Menu button for 5 seconds to enter ‘Installation Menu’ and entering service menu are
available. (In-Start, Power-Only, Adjust, Installation Menu…)
System Provider Mode
•‘System Provider Mode’ allows access to the menu system from the front panel or remote control but access is controlled as follows:
-When value is ‘On’, Accessible Items on the menu system, others are not permissible. (Depending on model)
»Input select screens
»Sleep timer
»Aspect Ratio
»Caption
»Channels (Except for Channel Tuning & Settings and Channel Manager)
»Input Manager
ENGLISH
22
DTV Channel Update
-It is a mode to set whether to update DTV Channel automatically or not.
-When is set to ‘Auto’, the function to update TV’s Channel map according to DTV Channel’s stream information.
- When is set to ‘Manual’, the function to keep TV’s Channel map even though DTV Channel’s information is changed.
Power On Default
-Set the channel to display and Volume Level, etc. when turn on power.
-When is set to Off, it is not applied to the subordinate Input, Channel, A/V Setting, Aspect Ratio menu.
-When is set to On, it can set by entering the subordinate menu.
Input
-Set whether it is turned on by the set input source or by the last stored input source.
Channel
-Select start channel number if Input source’s value is TV.
A/V Setting
-If ‘A/V Setting’ is changed from ‘Off’ to ‘On’, A/V parameters that are set before entering ‘Installation Menu’ are applied whenever turn on
power.
Aspect Ratio
-The aspect ratio determines the default aspect ratio that the set returns to on power up.
Aux Source Setting
-Set to On or Off.
-The Auxiliary (Input) Source Setting feature will enable or disable for each external input.
-User cannot disable the current input.
Power Management
•The Power Management feature will turn o the TV if no input control command is received from either the Local or IR Key within a selected
hours.
-Activity on either of these inputs shall reset the ‘Power Management’ timer.
-This entry can be set to a value which is corresponding to the desired hours (1Hour to 7Hours).
-Default value is 'Off'
Factory Reset
-Change all settings to their default values.
ENGLISH
23
Network
(Depending on model)
MAC Address
•Displays the MAC address (not customizable).
Network Setting
One-click network connection
•Connects easily to a network.
•This menu supports to connect to an available network.
To connect to a network through Set Expert
• For use in special circumstances such as in oces (in cases where a static IP is used).
1 Select a network connection, either Wired or Wireless. (Wireless is supported depending on model)
2 When connecting via Wired, Congures the IP settings of the TV set. You can set the IP address, subnet mask, gateway and DNS server.
3 When connecting via Wi-Fi, use the one of the following network connection methods.
AP List
Connects to the network selected from the AP List.
Enter the SSID
Connects to the wireless AP typed in.
WPS-PBC Connects easily when the button of a wireless AP supporting PBC is pressed.
WPS-PIN Connects easily when the PIN of the wireless AP that you wish to connect to is entered in to the
AP website.
Advanced Wi-Fi Settings
After connects Wi-Fi, you can set the IP address, subnet mask, gateway and DNS server.
ENGLISH
24
LG Connect
(Depending on model)
•Sets the ‘LG Connect’ function to On or O.
-You can connect TV via 'LG TV Plus' app in smart device.
-Default setting is 'On'.
IP Stream Control
(Depending on model)
Audio PTS Offset
•Controlling output stream timing of audio.
•You can set the ‘-500~500’. (Change step is -10 or +10)
Video PTS Offset
•Controlling output stream timing of video.
•You can set the ‘-500~500’. (Change step is -10 or +10)
IGMP
•You can set IGMP version. (2 or 3)
Wake On LAN
•Sets the Wake On LAN function.
-The Wake On LAN feature enables the TV to receive software updates and/or be powered ON upon receipt of Wake Up Frame packets
and/or Magic Packet data via the wired LAN. To facilitate use of this feature, note that the appropriate wired connection must be made.
(‘Wake up Frame’ - Depending on model)
VLAN ID
(Depending on model)
•This menu provides TV with VLAN settings.
•Recommend that the network manager set this menu.
•If you set dierent ID between switch and TV, you cannot use network.
LAN ID
•Set VLAN ID for TV network.
Aux LAN ID
(Depending on model)
•Set AUX LAN ID for devices connected via port.
Server Settings
(Depending on model)
•Sets the information to connect to the external server.
CMS Server
•Sets the network information to connect to SuperSign CMS. (or other compatible solutions)
Control Server
•Sets the network information to connect to SuperSign Control. (or other compatible solutions)
ENGLISH
25
Ping Test
(Depending on model)
•Check your network status with the ping test.
ENGLISH
26
Pro:Centric
(Depending on model)
Mode
•Sets whether or not enable Pro:Centric and the service method.
•You can set to O, Conguration Only, GEM or HTML. The default value is O. (‘Mode’ items is dier depending on model)
Update Event
•When Update Event is set to ‘Enable’, Hour and Minute items are enabled and then the Update Event function is enabled.
•When Update Event is set to ‘Disable’, ‘Hour’ and ‘Minute’ items are disabled and then the Update Event function is disabled.
Room Number Setting
•You can set Label and Room Number using the Room Number Setting.
Media Type
(Depending on model)
•Sets the media type to RF or IP.
•The default value is RF.
RF
(Depending on model)
•Data Channel
-Sets the Channel at which the Pro:Centric data is received.
ENGLISH
27
IP
•P:C IP Setting
-Server Address is set to IP Address.
-Can select IPv4 or IPv6 type using 'IP Type'. (Depending on model)
(IP Address) Set IPv4 or IPv6 address.
(Port Number) Sets the actual port or number where the Pro:Centric server is running.
-Server Address is set to Domain Name.
(Domain Name) Sets the domain name where the Pro:Centric server is running.
(Port Number) Sets the actual port or number where the Pro:Centric server is running.
-The default value of IP(IPv4) is 0 and the range is between 0 and 255.
-The default value of IP(IPv6) is 0 and the range is between 0 and FFFF.
-The default value of Port is 0 and the range is between 0 and 65535.
Receive Data
(Depending on model)
•Sets Enable or Disable.
ENGLISH
28
General
Conguration Setup
Select RCU
•It is a mode to set whether to use Select RCU or not. When ‘Select RCU’ is set to ‘Enable’, You can adjust ‘Number of RCU’ menu.
Number of RCU
•Number of RCU value range 1~9. (When ‘Select RCU’ is set to ‘Enable’)
•Number of RCU value range 0. (When ‘Select RCU’ is set to ‘Disable’)
-RCU (Remote Control Unit) : It is special RCU that operates only setted number of RCU in TV.
RS232 DC Power Outlet
(Depending on model)
•It is a mode to decide whether to output DC or not for power supply to IB Box in Installation Menu. We oer a output terminal in one Pin of
RS232C Jack for the use of communication.
•5 V DC Power Outlet and 12 V DC Power Outlet must operate mutually exclusively. That is, only one of the two sides must be turned on.
-You can select OFF, ‘5 V’ or ‘12 V’.
»When select ‘5 V’ the 5 V is forwarded through the port. when select ‘12 V’ the 12 V is forwarded through the port.
RS-232CIN
(CONTROL & SERVICE)
Interface box
ENGLISH
29
»Type of Connector: D-Sub 9-Pin Male
Male connector on box, viewed towards connector.
No. Signal Signal requirements
1VCC
2 RX RS232 Standard RS232 specication
3 TX RS232 Standard RS232 specication
4IR from TV
5 GND Power ground
6, 8 Not connected
7 2 A +5 V DC 10 %, max 100 mV ripple
9 1.5 A +12 V DC 10 %, max 100 mV ripple
One Channel Map
(Depending on model)
•If set to ‘Enable’, the TV will operate as below.
-A. When the TV is auto-scanning, it searches both air and cable channels.
-B. User can assign a channel number him/herself by manual scan.
-C. In 'Channel Edit’ window, all channels are shown in a single list regardless of input source.
-D. Automatically scanned channels may not have the user-desired channel numbers.
•If user change the ‘Enable/Disable’ value, an pop-up window will be displayed to warn that all channel will be deleted. The Default value is
‘Enable’.
DTV Channel Update
•It is a mode to set whether to update DTV Channel automatically or not.
•When set to ‘Auto’, the function to update TV’s Channel map according to DTV Channel’s stream information.
•When set to ‘Manual’, the function to keep TV’s Channel map even though DTV Channel’s information is changed.
On Timer Operation
•It is a mode to select ‘Timer Power On’ working one time or repeatedly.
•'Once': ‘Timer Power On’ in the user menu operates only one time when the Timer Power On menu is set to On.
•‘Repeat’ : ‘Timer Power On’ operates repeatedly when the Timer Power On menu is set to On.
USB Auto Playback
(Depending on model)
•When ‘USB Auto Playback’ is set to ‘Movie’, TV nds and plays the USB’s movie les located at the root(top) directory Movies if USB is plugged in.
•When ‘USB Auto Playback’ is set to ‘Photo’, TV nds and plays the USB’s photo les located at the root(top) directory Photos if USB is plugged in.
•If it reaches the last le, it starts the rst le again
ENGLISH
30
15Min Auto Off
(Depending on model)
•When set to ‘Enable’, TV will turn o if there is no signal in 15Min.
Auto Sensing
•If ‘Auto Sensing’ is set to ‘On’, the input is automatically switched when the input signal that you set to “ON’ is received.
•If ‘Auto Sensing’ is set to ‘Disable’, the input is not switched when the input signal is received.
-SIMPLINK and Auto Sensing cannot work simultaneously. If SIMPLINK is set to On, Auto Sensing is automatically set to Disable.
-If the signal is removed while Auto Sensing (automatic input switch) is enabled, the input returns to the previous setting.
If the several input are connected by enabling Auto Sensing and the automatic input returns to the previous setting.
If the several inputs are connected by enabling Auto Sensing and the automatic input switch is performed several times, the input
returns to the previous setting only for the last input and does not repeat the operation for the rest.
InStant On
(Depending on model)
•Set to ‘Instant On Mute Mode’ or ‘Instant On Reboot mode’ to enable the Instant ON feature. The Instant ON feature allows the TV to turn ON
when AC power is applied, but with video and audio muted (Muted ON). The TV retains its ON status while appearing to be OFF. Pressing the
POWER button toggles O/On the video and audio mutes, so that the TV appears to turn ON instantly.
-If this item is set to Instant On Mute Mode, the TV will not reboot to check for and download updates at turn OFF. TV seems to be turned
off to user(panel is off), but both micom and chipset are on.
-If this item is set to Instant On Reboot mode, the TV will reboot to check for and download updates from the Pro:Centric server at every
turn OFF.
-If this item is set to Instant On Mute mode or Instant On Reboot mode when ‘WORF’ is ‘Disable’, ‘WORF’ is set to ‘Enable’ and ‘Update Time’
is set to auto(random) time. (Depending on model)
Insert Image
(Depending on model)
•Set to On or O.
•It is a mode to decide whether to display background image when using Clock app, Bluetooth Sound Sync app, Audio Programme app, No
Signal state and watching Radio programme.
•You can download the background image at TV Manager app.
No Signal Image
(Depending on model)
•Set to On or O.
•It is a mode to decide whether to use no signal image when there is no signal.
No Signal Text
(Depending on model)
•Set to ‘On’ or ‘O’.
•It is a mode to decide whether to use no signal text when there is no signal.
DPM
(Depending on model)
•You can congure the DPM (Display Power Management) function.
•If this option is not set to O, the TV set enters the DPM mode when there is no input signal.
•If you set this option to O, the DPM function is disabled.
ENGLISH
31
PM Mode
(Depending on model)
•Power O (Default)
-Set the normal DC Off mode.
•Sustain Aspect Ratio
-Set the power mode of the HDMI Switching IC, which detects HDMI external input signals in the TV Standby state after DPM Power Off
turns off the TV.
•Network Ready
-Set the Network Ready mode.
-TV seems to be turned off but it keeps to be on internally.
-TV goes through the normal DC On process when it turns on.
Healthcare Headphone Mode
(Depending on model)
•Healthcare Headphone On
-Mute is always applied to TV Speaker.
-Sound Out menu is displayed as Internal TV Speaker + Wired Headphone, and all Sound Out submenus are gray out (Disable).
-Internal TV Speaker / Headphone Simultaneous output, Volume key is adjust TV volume (Mute off).
-Select TV Speaker User Interface. Volume key adjusts the internal TV Speaker volume.
-Select Headphone User Interface. Volume key adjusts the headphone volume.
•Healthcare Headphone O
-Sound Out Normal Scenario on Commercial Hotel TV.
-Sound Out has Menu in default mode (Internal TV Speaker + Audo Out (Optical)).
Screen Saver
(Depending on model)
•When the currently displayed app has not received any user input for an hour, it will be replaced by a Screen Saver.
•If you turn this option ‘O’, the current picture may create an afterimage burned onto your screen, possibly permanently.
Default Sound Out
(Depending on model)
•You can configure the Sound Out to be set after power on.
•You can select Off, TV Speaker, Optical, LG Sound Sync., HDMI ARC
•If you set this option to Off, the TV maintains Sound Out after power on.
•If you set this option to HDMI ARC, SIMPLINK is enabled.
•If a SIMPLINK-enabled device is connected to the TV and item SIMPLINK is enabled, the SIMPLINK device Audio Mode will have priority over the
setting of this item when the TV is turned ON.
USB Power
(Depending on model)
•You can control the power status of USB port according to the mode. Set to ‘Default’ or ‘Warm O’ to enable the USB Power feature.
-Default : When the TV is turned on, the USB device is powered. USB devices can be used regardless of 'Instant On' state.
-Warm Off: When the TV is turned on, the USB device is powered. USB devices are available.
However, if ‘InStant On’ is ‘Instant On Mute
Mode’ or ‘Instant On Reboot’ mode and TV State is ‘Instant On’, the USB device is powered off.
•Please do not turn o the display when the connected USB storage device is working.
•When Turned o the power of USB storage device is suddenly, the stored les or the USB storage device may be damaged.
ENGLISH
32
External Speaker
(Depending on model)
Volume Control
•Selects the volume control method of an external speaker.
•You can select ‘O’, ‘Int Variable’ Fixed. ‘Ext Variable’. (Depending on model)
•Ext Variable uses the External Vol Up/Down Control Line to change the volume up to 2 Watts.
•Int variable is linked to the main volume OSD and change the volume 0 - 2 Watts.
•Fixed produces a xed output. The default is O.
Output
•This item is enabled when Volume Control is set to Fixed. You can choose one of 7 steps. (0.01/0.03/0.05/0.1/0.2/0.5/1/1.5/2 Watts).
•The Default is 1 Watt.
•Some models support the volume up to 1Watts.
Set ID Setup
Set ID Lock
•Set the ‘Set ID’ item in GENERAL Menu whether to activate or not.
•Set to On (Work) or O (Do Not Work).
Set ID
•Set the ‘Set ID’ of TV Set with 1~99.
Power Saving
Static Saving
•It is the item for setting the level to reduce the backlight control from the items for saving the consuming power, which is increased or
decreased by 10 steps from 0 to 100. 100 makes the consuming power set to the same one from the TV. 0 reduces the consuming power to the
minimum. The default value is 100.
-The value displayed at the OSD is not changed and only the actual setting value is converted to percentage based on the static saving
value to set.
-0 ~ 30: HIGH, 40 ~ 60 : MID, 70 ~ 90 : LOW, 100 : OFF.
Keyless Off Hours
•Automatically TV will be turned o if there is no key input for the preset time period.
ENGLISH
33
HCEC Setup
(Depending on model)
CEC Mode
(Depending on model)
•You will have 3 modes to choose [Default], [HCEC] and [TVLink-CEC].
•If [Default] is selected, you can use SIMPLINK which is provided in LG TV. Also you can enable and disable SIMPLINK through SIMPLINK MENU.
•If [HCEC] is selected, you can use TVLink-HCEC Protocol. (For more detailed information, please refer to TVLink-HCEC Protocol document)
•If [TVLink-CEC] is selected, TV will not directly work for key input except for power key. And volume related keys will work just in case of
Follower volume control mode. (For more detailed information regarding the scenario of volume control, please refer to “TVLink-CEC protocol”
document)
IR Decoding
•When ‘IR Decoding’ is set to ‘Enable’, the TV decodes and changes it into a CEC Message and sends it to Command via the HDMI CEC Line. The
default value is Disable.
Device ID
•Sets the ID of a device(Logical Address) connected to the CEC Line. You can choose ‘All’ and from ‘0 x 01’ to ‘0 x 0E’(All, 0 x 01 ~ 0 x 0e).
•The default value is ‘All’.
StandBy
•Set the sending and receiving scenario of OpStandBy(0 x 0c) command.
•Ths detailed scenario is described on the table below.
Send Receive
Send Only O X
Receive Only X O
All O O
O X X
Forced Initialize
•This setting will be enabled When CEC mode is set as ‘TVLink-CEC’.
•If ‘Enable” is selected, TV will change its input source to HDMI1 by any HDMI-CEC simulation from a device.
HTNG Public Display Mode
(Depending on model)
• If you use following functions via TVLink-HCEC, HTNG Public Display Mode will be set as “Yes” automatically.
-Power On Default, Start Volume, Maximum Volume, Minimum Volume, or Start Volume.
•Even if ‘Public Display Mode’ is set as No, above settings are still eective.
ENGLISH
34
Clock Setup
(Depending on model)
Clock Display
(Depending on model)
•You can select ‘Enable’ or ‘Disable’.
•After selecting ‘Enable’, you can see the LED Clock TV.
Dimming Standby
(Depending on model)
•Standby Dimming value Range : 1~2
Dimming PowerOn
(Depending on model)
•PowerOn Dimming value Range: 1~5
Clock Source
•You can select ‘O ’, ‘Pro:Centric’, ‘TV’, ‘NTP’, ‘Admin’.
•NTP : Clock is synchronized using Network Time Protocol. It’s only enabled when network cable is connected.
•Admin : It’s automatically set to Admin when clock is updated by commercial protocols like TVLink-HCEC, TVLink-Interactive, or HCAP API.
•O : Clock is synchronized using any available clock source.
•Pro: Centric : Clock is synchronized using Pro:Centric server. (Depending on model)
•TV : Clock is synchronized using particular TV channel.
-Input (Depending on model)
»You can select 'Input' according to 'Clock Source'.
»You can select 'RF' or 'IP' when Clock Source is 'Pro:Centric'.
»You can select TV source when Clock Source is 'TV'.
»Input is set to 'None', 'HCAP', 'Protocol', 'HTNG' automatically when Clock Source is 'Admin'.
-Channel / Frequency (Depending on model)
»Sets the Frequency to get the time information when Clock Source is 'Pro:Centric'.
»You can select channel when Clock Source is 'TV'.
-Timezone (City) / Timezone (Custom) / Timezone (Offset) (Depending on model)
»In the case when there is difference between the time information received from the Teletext and the time of the current area, it can
be set up to correct this. The initial value is 0, and it can be changed in the range of -12 Hrs ~ +14 Hrs. (Timezone (Offset) range is -12
Hrs ~ +12 Hrs)
Password Change
•To ensure more security, Password can be changed by installers’ own design.
1 Change password by using virtual keyboard.
2 Input the password again for conrmation.
Lock Mode
•If ‘Lock Mode’ is ‘Yes’, the following features will be unavailable.
USB
•If it is set to ‘Enable’, USB devices do not work in relative features. (Exclude S/W update)
Factory Reset
•If it is set to ‘Enable’, User Menu General Reset to Initial Settings is disabled.
ENGLISH
35
Welcome Video Mode
(Depending on model)
•You can set to O, Once or Repeat.
Operation
•The video displays after your TV is turned on and the boot logo appears.
•If Welcome Video is enabled and a video is downloaded on the TV, the video plays.
•The time it takes a video to be displayed may dier depending on the decoding time of the video.
•Controls for playing the video are not available. (Pause, stop, fast forward, etc.)
•Videos in any le format that the TV supports can be downloaded and displayed.
Crestron
(Depending on model)
•This function enables synchronization with applications provided by Crestron.
•Server: This menu sets the server’s IP address for the network connection with the server. (equipment provided by Crestron)
•Port (1024~65535): This menu sets the port for the network connection with the server. The default port number is 41794.
•IP ID (3-254): This menu sets a unique ID for synchronizing with the application.
Developer Mode
(Depending on model)
•This feature provides great convenience to the app developers.
•Set up to install the Developer mode app.
Portal Settings
(Depending on model)
Portal Mode
(Depending on model)
•You can select ‘Default Portal’ (Use webOS default portal), ‘Customizable Portal’ (Use editable Portal), or ‘None’ (Do not use portal).
ENGLISH
36
Auto Start
(Depending on model)
•You can select ‘O’, ‘Website Shortcut’, or ‘Portal Mode’.
•If you select ‘Website Shortcut’, Shortcut app will be excute automatically after TV on.
•If you select ‘Portal Mode’, Portal(Home Launcher) will be excute automatically after TV on.
PreLoaded App
(Depending on model)
•If you want to use a particular app, you can choose from the menu. you can setting each apps activation.
Website Shortcut
(Depending on model)
Shortcut
•Sets Enable or Disable. When it is set to Enable, Website Shortcut app is displayed at launcher bar.
Shortcut Name
•You can set Website Shortcut app name (title).
Shortcut URL
•Sets URL to connect when excute Website Shortcut app.
Shortcut Icon
•You can select default icon, fav icons, downloaded icon or Download(Go to TV Manager).
•You can download the shortcut icon at TV Manager app.
Tile Color (Color Code)
•You can change Website Shortcut app tile color using RGB color code.
Input Shortcut
Shortcut
•Sets Enable or Disable. When it is set to Enable, Input Shortcut app is displayed at launcher bar.
Shortcut Name
•You can set Input Shortcut app name (title).
Shortcut Icon
•You can select default icon, downloaded icon or Download(Go to TV Manager).
•You can download the shortcut icon at TV Manager app.
Tile Color (Color Code)
•You can change Input Shortcut app tile color using RGB color code.
Hotel Directory
(Depending on model)
•Set the information to display at Hotel Directory app.
ENGLISH
37
Facility or Service Name
•Set the facility or service name.
Details or Extension
•Set the detailed information.
Related Photo
•You can select None, downloaded images or Download (Go to TV Manager).
•You can download the directory images at TV Manager app.
Portal Editor
(Depending on model)
•If you press ‘Portal Editor’ menu, each portal editor is launched according to ‘Portal Mode’.
Customizable Portal
•Template
-You can set Template when selecting focus. Select between Bar Type or Tile Type (City, Beach, and Forest).
•Hotel Video
-You can set this mode to On/Off when selecting Customizable Portal.
-You can download the video at TV Manager app.
•Welcome Message, Hotel Name
-You can set the welcome messages and hotel name.
•HOTEL Logo
-You can select images for Default/Downloaded image.
-You can download the icon at TV Manager app.
Portal Manager
(Depending on model)
This feature enables you to group together multiple monitor sets on a single network into the same group and copy portal setting data on a group
basis. This feature has two modes, Master and Slave.
Master
•Add, edit, and delete group.
•Distribute your device’s portal data.
•All monitor sets initially come in Master mode.
Slave
•Remove monitor sets for their groups.
•Monitor sets that have been added to a group are automatically switched to Slave mode. Conversely, when a monitor set has been deleted
from a group, it is automatically initialized and switched to Master mode.
•If a new Slave has been added to an existing group, or if the portal data has not been properly distributed from master, the Cloning button will
be activated.
•You can duplicate the master device’s portal setting data by using Cloning.
ENGLISH
38
GROUP MANAGEMENT
•Creating a New Group
1 Click Add New Group.
2 Enter a group name.
3 Click Add Device, select the devices you wish to add to the group, and add them.
4 Click Done, and you will see that a new group has been created.
•Editing a Group
1 Click the group you wish to edit.
2 Add a new device by using Add Device.
3 Delete a device by using Delete Device.
4 Check whether the devices in the group are connected to a network by using Device Check.
5 If there are any sets of devices in the group that are not portal data synchronized, Distribute button will be activated.
6 You can re-distribute the master device’s portal setting data to the group by using Distribute.
•Deleting a Group
1 Click Delete Group.
2 Select the group you wish to delete and click Delete.
3 Check that the group you selected has been deleted.
•ALL DEVICES VIEW: All Devices View: This page enables you to manage all slave monitor sets that are connected to the same network.
1 Click All Devices View.
2 Click Reset Device Mode.
3 Select the slave monitor set whose device mode you wish to change and click Initializing.
PORTAL DISTRIBUTION
1 Select your desired group and click Distribute.
2 Set power o on the slave sets by using remote controller after distribution is completed.
3 Check that the data have been copied on the slave sets after a 1 minute.
* How to Use
•Monitor: Run, add, delete or edit app on the portal setting of the installation menu
•You can create up to 25 groups.
•You can add up to 12 slave devices to a group.
•A list of devices you can add to your desired group appears only when the following conditions have been met:
-The devices you wish to add must be on the same network as the master device.
-The devices you wish to add must be in Master mode, and they must not belong to any existing group.
-The UPnP feature must be enabled (go to General Network UPnP and set it to On).
•It may not work properly in wireless network environments. It is recommended you use a wired network.
ENGLISH
39
Media Share
(Depending on model)
SmartShare
(Depending on model)
•Smart Share enables DLNA function. If this value is enabled, TV acts as Media Player and displays Media Server contents through Smart Share
app.
Screen Share
(Depending on model)
•Screen Share enables WiFi p2p functions. If this value is enabled, Screen Share app is displayed at launcher bar and TV can display the screen of
mobile phone or laptop.
•If you want Completely Exit Screen Share App, Click ‘X’ Button on right top side.
Media Renderer
(Depending on model)
•Media Renderer enables the TV to act as a Media Renderer device to receive contents from devices on the same network.
DIAL
(Depending on model)
•With this DIAL service, you can launch the target app at Smart Home Launcher bar without select the target app by remote controller. Before
this function enables, the target app should be selected at Installation Menu Portal Settings Preloaded App.
TV Name
•When media devices(ex: smart phone, desktop, laptop) are searching TV, this string will be displayed.
SoftAP
(Depending on model)
•SoftAP is similar to Access Point. When you enable this function, TV acts as an Access Point.
•Regardless of the Instant On mode, the SoftAP setting stays unchanged after power o/on. (Depending on model)
Use Default
•If you want to use default password(this password was generated randomly), you must select ‘Enable’ in this item.
ENGLISH
40
Security Key
•If you want to change default password, you need to change ‘Use Default’ value into ‘Disable’.
Wi-Fi Signal Strength
•You can control wireless signal strength on SoftAP. This is controlled by 5 step. If you select ‘Not Used’, wireless signal strength will be set to Max
value.
Wi-Fi Channel
•You can control wireless channel on SoftAP mode. This is controlled from 1 to 11 channel. If you select ‘Auto’, wireless channel of SoftAP will be
set to random channel.
Mode
(Depending on model)
•You can select NAT(Network address translation) mode and BRIDGE mode for Soft AP.
Security Type
(Depending on model)
•You can select ‘WPA2-PSK’, ‘WPA2-Enterprise’ and ‘Open’ if you selected ‘BRIDGE’ mode.
Radius Server IP, Radius Server Port, Radius Server Key
(Depending on model)
•You should enter Radius Server information if you selected ‘WPA2-Enterprise’.
VLAN ID
(Depending on model)
•SoftAP VLAN ID is needed when you want to separate TV packets and SoftAP packets.
•The packets via SoftAP are tagged when the packets go through LAN port to external network.
•It is not compatible with Network -> VLAN ID. (SoftAP VLAN is not available if LAN port or AUX port in VLAN ID is set.)
ENGLISH
41
Beacon
(Depending on model)
•This option enables BLE Beacon, one of Bluetooth 4.0’s features.
•Beacon Mode (On/O Toggle): enables the Beacon feature.
•The iBeacon/Eddystone Type Beacon features are supported.
iBeacon
•Beacon UUID (hex): Set the UUID.
1 Field1: 4byte hex value (8 digits)
2 Field2: 2byte hex value (4 digits)
3 Field3: 2byte hex value (4 digits)
4 Field4: 2byte hex value (4 digits)
5 Field5: 6byte hex value (12 digits)
•Major (0–65535): Sets the Major value.
•Minor (0–65535): Sets the Minor value.
Eddystone
•Frame: Set UUID or URL.
-Beacon UUID (hex): Set the UUID
1 Field1: 10 byte hex value (20 digits)
2 Field2: 6 byte hex value (12 digits)
-Setting the URL method
»URL Prefix: Sets the prefix of the URL.
»URL Suffix: Set the suffix of the URL.
»URL: Enter the part of the URL that excludes the prefix and suffix.
»URL string length is limited to 15 characters.
OK
•The button used to conrm and apply the settings that you have entered.
•Some models do not support background screening services in iOS.
•A reboot is recommended for the settings to be applied properly.
•The UUID value is hexadecimal and the exact number of digits must be entered.
•The distance of the beacon may vary depending on the external device.
•Beacon’s distance may vary depending on the app you use on your external device.
•The Beacon feature uses Bluetooth Low Energy (BLE) technology and is therefore susceptible to radio waves. 2.4 GHz environment if
not, normal operation may not be possible.
ENGLISH
42
TV Manager
* Image shown may differ from your TV.
You can update les from USB to TV through the TV manager.
Diagnostics
(Depending on model)
•Sets Enable or Disable. When it is set to Disable, user can’t control TV via RMS. The changed setting is applied after reboot.
ENGLISH
43
Ez Download
* Image shown may differ from your TV.
•Ez Download is a function that enables users to download the desired items all at once, such as EPK (software update le), TLL, Media les,
Micom, Pro:Idiom M Key. (Depending on model)
-Media files, Pro:Idiom M Key file and Software Update files should be copied into the folder named LG_DTV on the USB.
»TLL files should be copied to the root folder of the USB.
»If you press ‘EZ Download’ menu, EZ Download is launched.
»If .DZM file exist file will be selected previously download file.
»For Pro:Idiom M key to appear, "pim" file must exist in USB.
»Pro:Idiom M key file name should be specified as checksum with MD5 and extension should be specified as “pim”. (case-insensitive)
»Pro:Idiom M Key file should be encoded by ANSI(ASCII).
»Pro:Idiom M Key file length should be 1024 bytes. (32 bytes * 32)
»If file name or the length are wrong, the file download will be failed.
»If you do “Factory Reset”, Pro:Idiom M Key will return back to default Key.
•If the DZM le is still in the USB after the download is complete:
An Ez Download pop-up window will appear and list the le types, such as EPK (software update le), TLL, Media les, Micom,
Pro:Idiom M key with the previously downloaded lists checked automatically.
ENGLISH
44
•Press button to display storage usage information.
•Press the “CLEAR STORAGE” button to delete the downloaded media les.
ENGLISH
45
Import Clone File
•Once the internal TV data and its channel map information are written to the USB memory card, the user can start “Import Clone File”
process with the data le generated and stored in USB memory card. The user should not turn TV o nor unplug the USB memory card while
processing. The following reference images might be slightly dierent.
ENGLISH
46
Export Clone File
•“Export Clone File” creates “TLL” le in USB root folder. “TLL” le can be used to “Import Clone File”. While writing is in process, the user must not
turn TV o nor unplug the USB memory card. The following reference images might be slightly dierent.
ENGLISH
47
USB Download Menu
USB Cloning
•An Installation can quickly set up and clone multiple TV sets at a property. These cloned TVs will all have the same Master TV Setup: Public
Display Mode Installation Menu settings, User A/V settings and the channel Map. This newer procedure signicantly decreases the installation
time that would be necessary if the standard RS-232C method were used instead.
1 Overview USB Cloning Procedure
: Commercial TVs have the capability to support cloning internal TV data and channel information with an external clone device called “USB
Cloning”, in order to copy TV data accurately and quickly. The clone internal functions use slightly dierent internal processes for the two
types of commercial TVs. However, the UI of cloning feature remains the same in both. Regarding the demands over the current cloning
feature for quicker cloning, better portability and etc, we would like to announce the cloning process via USB port, named as USB Cloning.
USB cloning process is divided into 2 main processes. One is writing the previously saved TV data into the TV, and one another is reading
of current TV data into USB memory card. To avoid any confusion due to the words, it is clearly specied as “Import Clone File” and “Export
Clone File” in the whole process.
2 Data To Be Cloned
: The data cloned are the same data cloned by previous USB Cloning. Details are explained in the following:
-TV data includes :
A. Installation Menu settings
B. Main menu settings (Audio, Picture etc)
-Analog / Digital Channel information includes:
A. Channel numbers
B. Channel label
C. Channel attributes including channel type, skipping status and etc.
ENGLISH
48
Image Download
* Image shown may differ from your TV.
•The download sequence is Image Download Select Image(s) Download.
•The target le is located in LG_DTV folders.
•Press the “CLEAR STORAGE” button to delete the downloaded images.
-Boot Logo Image
(Depending on model)
»Boot Logo Image can download only one file.
»Boot Logo Image update function supports only JPG, JPEG, BMP format file of less than 8 MB filesize.
»We recommend you that splash image resolution match the TV`s panel resolution.
»Max resolution of splash image : Full HD 1920 x 1080, HD 1360 x 768.
»Min resolution of splash image : 64 x 64.
-Apps Background Image(s) & Hotel Directory Image(s)
(Depending on model)
»Image update function supports only JPG, JPEG, PNG format file(s).
»Max resolution of image : UHD 3840 x 2160, Full HD 1920 x 1080, HD 1360 x 768.
»Min resolution of image : 64 x 64.
»The maximum number of images to choose from per feature is 12.
»Images per feature can not be downloaded beyond 10 MB.
»If you updates the images, original images will be removed.
»If you want to use inserted image in Clock app, Bluetooth Sound Sync app, Audio Programme app, No Signal state and watching Radio
programme please change the value of ‘Insert Image’ property to enable (‘Insert Image’ in Installation General Configuration
Setup).
ENGLISH
49
Icon Download
(Depending on model)
•Images is located in LG_DTV folder.
•If you updates the images, original images will be removed.
•The download sequence is Icon Downalod Select Images DOWNLOAD.
•Icon Image can download only one le.
•Icon update function supports only JPG, JPEG, PNG format le.
•Max resolution of icon : UHD 3840 x 2160, Full HD 1920 x 1080, HD 1360 x 768.
•Min resolution of icon : 64 x 64.
•Press the “CLEAR STORAGE” button to delete the downloaded icons.
ENGLISH
50
Video Download
(Depending on model)
•Media les is located in LG_DTV folder.
•The download sequence is Video Download Select media le DOWNLOAD.
•Media les can only download one le each.
•If you updates the video le, original le will be removed.
•Press the “CLEAR STORAGE” button to delete the downloaded videos.
ENGLISH
51
Software Update
►Update TV Software
•This feature updates TV software through the EPK le in USB.
•The target le is located in LG_DTV folder.
•The download sequence is Software Update Update TV Software Select le(EPK) UPDATE.
►Update Micom Software
•This feature updates Micom software through the txt le in USB.
•The target le is located in LG_DTV folder.
•The download sequence is Software Update Update Micom Software Select le(txt) UPDATE.
ENGLISH
52
CONTENT MANAGER
(Depending on model)
Web Login
•Dierent features are supported depending on the product.
This Signage product comes with a feature that enables you to access it on your PC or mobile device.
-Content Manager, Group Manager 2.0, Log Out, Change Password menus are provided.
•URL: https://set ip:443
•The default password: 00000000
•Supported resolutions (this program is optimized for the following resolutions):
-PC 1920 x 1080 / 1280 x 1080
-Mobile: 360 x 640(1440 x 2560, 1080 x 1920), DPR
•Supported browsers (this program is optimized for the following browsers):
-PC 1920 x 1080 / 1280 x 1080
Content Manager
Player
(Player)
The Content Manager app’s player feature enables you to play/manage contents of video, image, template, SuperSign and playlist in an integrated
way. (The OLED models do not support the playback and management of image content and template content.)
•Continuous Play
1 Select your desired type of content from the tab on the left and then select your desired content.
2 Click PLAY in the upper right-hand corner of the screen and enjoy the content you have selected.
•Export
1 Select your desired type of content from the tab on the left and click Export in the upper right-hand corner of the screen.
2 Select the content you wish to export.
3 Click COPY/Orbiter in the upper right-hand corner of the screen and select the device to which you wish to export the content. (If a
content le stored on the target device has been selected, the processing of the content le is skipped.)
4 You can see that the content has been moved/copied to the device.
•DELETE
1 Select your desired type of content from the tab on the left and click DELETE in the upper right-hand corner of the screen.
2 Select the content you wish to delete.
3 Click DELETE in the upper right-hand corner of the screen.
4 You can see that the content has been deleted.
•Filter / Sort
1 Click Filter / Sort in the upper right-hand corner of the screen.
2 1) Choose your desired sort criterion to sort content les either by le name or in the order they have been played (the most recently
played le shown at the top of the list).
2) It is possible to only view the content stored on your desired device by ltering content les by device.
3) It is possible to only view the content of your desired type by ltering content les by content type.
ENGLISH
53
•Create Playlist
When creating a playlist, you cannot include characters that cannot be used in le names on Windows — such as \, /,:, *,?, “, <,>, and | — in
the names of the les in the playlist. In addition, if the playlist contains content les whose names include such characters, you cannot move or
copy the playlist.
1 Select the Playlist tap from the tab on the left and click Create Playlist in the upper right-hand of the screen.
2 Select the content you wish to add to the playlist and click NEXT in the upper right-hand of the screen.
3 Set a play time for each piece of content (applicable only for photo and template content), as well as other items such as Conversion
Eect, Ratio, and Auto Playback, and then click DONE button in the upper right-hand corner of the screen.
4 You can see a new Playlist has been created.
•DISTRIBUTION
1 Click Distribute in the upper right-hand corner of Playlist tab screen.
2 Go to the Group Manager app to distribute the created playlists.
Scheduler
(Scheduler)
The Content Manager app’s scheduler feature enables certain content to be played at a scheduled time through a playlist or external input.
•Creating a Schedule
1 Click New Schedule in the upper right-hand corner of the screen.
2 Choose between Playlist and Input Source.
3 1) If you have selected Playlist, select the playlist you wish to schedule the playback of.
2) If you have selected Input Source, select the external input source you wish to schedule the playback of.
4 Enter schedule information and create a new schedule. (When creating a schedule, you cannot include characters that cannot be used
in le names on Windows — such as \, /,:, *,?, “, <,>, and | — in the name of the schedule le. In addition, if the playlist linked to the
schedule contains content les whose names include such characters, you cannot move or copy the playlist.)
5 Watch the playlist or external input you selected play back at its scheduled time.
•Importing a Schedule
1 Click Import in the upper right-hand corner of the screen.
2 Select the external storage device from which you wish to import a schedule.
3 Select the schedule you wish to import to your monitor. (You can only choose a single schedule.)
4 Click Select in the upper right-hand corner of the screen.
5 Check that the schedule has been imported to the monitor’s internal storage memory.
•Exporting a Schedule
1 Click Export in the upper right-hand corner of the screen.
2 Select the external storage device to which you wish to export a schedule.
3 Select the schedule you wish to export from your monitor. (You can choose multiple schedules.)
4 Click Select in the upper right-hand corner of the screen.
5 Check that the schedule has been exported to the external storage device you selected.
•Delete Schedule
1 Click DELETE in the upper right-hand corner of the screen.
2 Select the schedules you wish to delete.
3 Click DELETE.
4 Check that the schedules have been deleted.
•Calendar View
1 When you have registered schedules, click Calendar View.
2 You can see that the schedules registered are displayed in the form of a timetable.
•DISTRIBUTION
1 Click Distribute in the upper right-hand corner of the screen.
2 Go to the Group Manager app to distribute the created schedules.
ENGLISH
54
»If the schedule creation time overlaps, the previously created schedule is deleted.
»Schedule does not work while Scheduling list app is running.
Editor
(Editor)
The Content Manager app’s editor feature enables you to add your desired templates.
1 Select the template of your desired format.
2 Modify the template’s text.
2-1. Apply your desired font style (Size, Weight, Underline, Italic)
3 Modify the media le.
4 Save the template by clicking Save in the top right-hand corner of the screen.
5 Check that the template you saved is shown in the template list.
Supported Photo & Video Files
•Subtitles are not supported.
•The photo feature is not supported in OLED model.
* Supported video codecs
Extension Codec
.asf, .wmv Video VC-1 Advanced Prole (except for WMVA), VC-1 Simple and Main Proles
Audio WMA Standard (excluding WMA v1/WMA Speech)
.avi Video Xvid (excluding 3 warp-point GMC), H.264/AVC, Motion Jpeg, MPEG-4
Audio MPEG-1 Layer I, II, MPEG-1 Layer III (MP3), Dolby Digital, LPCM, ADPCM, DTS
.mp4, .m4v, .mov Video H.264/AVC, MPEG-4, HEVC
Audio Dolby Digital, Dolby Digital Plus, AAC, MPEG-1 Layer III (MP3), Dolby AC-4
.3gp
.3g2
Video H.264/AVC, MPEG-4
Audio AAC, AMR-NB, AMR-WB
.mkv Video MPEG-2, MPEG-4, H.264/AVC, VP8, VP9, HEVC
Audio Dolby Digital, Dolby Digital Plus, AAC, PCM, DTS, MPEG-1 Layer I, II, MPEG-1 Layer III (MP3)
.ts, .trp, .tp, .mts
Video H.264/AVC, MPEG-2, HEVC
Audio MPEG-1 Layer I, II, MPEG-1 Layer III (MP3), Dolby Digital, Dolby Digital Plus, AAC, PCM, Dolby
AC-4
.mpg, .mpeg, .dat Video MPEG-1, MPEG-2
Audio MPEG-1 Layer I, II, MPEG-1 Layer III (MP3)
.vob Video MPEG-1, MPEG-2
Audio Dolby Digital, MPEG-1 Layer I, II, DVD-LPCM
ENGLISH
55
* Supported Photo File Formats
File type Format Resolution
.jpeg, .jpg, .jpe JPEG
•Minimum: Min: 64 x 64
•Maximum: Normal Type: 15360 (W) x 8640 (H)
Progressive Type: 1920 (W) x 1440 (H)
.webp PNG •Minimum: Min: 64 x 64
•Maximum: 5760 (W) x 5760 (H)
.bmp BMP •Minimum: Min: 64 x 64
•Maximum: 1920 (W) x 1080 (H)
* Tips for using USB storage devices
•Only USB storage devices are recognized.
•USB storage devices connected to the monitor through a USB hub may not work properly.
•USB storage devices that use an automatic recognition program may not be recognized.
•USB storage devices that use their own drivers may not be recognized.
•The recognition speed of a USB storage device may depend on each device.
•Please do not turn o the display or unplug the USB device when the connected USB storage device is working. When the device is suddenly
separated or unplugged, the stored les or the USB storage device may be damaged.
•Please do not connect the USB storage device which was articially maneuvered on the PC. The device may cause the product to malfunction or
fail to be played. Remember to only use USB storage devices that store normal music, image, and/or movie les.
•Storage devices formatted with utility programs that are not supported by Windows may not be recognized.
•Please connect power to a USB storage device (over 0.5 A) which requires an external power supply. Otherwise, the device may not be
recognized.
•Please connect a USB storage device with the cable oered by the device maker.
•Some USB storage devices may not be supported or operated smoothly.
•File alignment methods of the USB storage device is similar to Windows XP and lenames can include up to 100 English characters.
•Be sure to back up important les since data stored in a USB memory device may be damaged. We will not be responsible for any data loss.
•If the USB HDD does not have an external power source, the USB device may not be detected. So make sure to connect it to an external power
source.
•Please use a power adapter for an external power source. No USB cable is provided for an external power source.
•If your USB storage device has multiple partitions, or if you use a USB multi-card reader, you can use up to four partitions or USB memory
devices.
•If a USB storage device is connected to a USB multi-card reader, its volume data may not be detected.
•If the USB storage device does not work properly, remove it and connect it again.
•The speed at which a USB storage device is detected diers from device to device.
•If the USB storage device is connected in Standby Mode, a specic hard disk will automatically be loaded when the display is turned on.
•The recommended capacity is 1 TB or less for a USB external hard disk and 32 GB or less for USB memory.
•Any device with more than the recommended capacity may not work properly.
•If a USB external hard disk with a Energy Saving feature does not work, turn the hard disk o and on again to make it work properly.
•USB storage devices (USB 2.0 or below) are also supported. However, they may not work properly in the videos list.
•A maximum of 999 folders or les can be recognized under one folder.
ENGLISH
56
Group Manager 2.0
(Depending on model)
This feature enables you to group together multiple monitor sets on a single network into the same group and to distribute content (schedules and
playlists) or copy setting data on a group basis. This feature has two modes, Master and Slave, and it can access the browser on your PC or mobile
device.
Master
•Add, edit, and delete group.
•Clone your device’s settings data.
•Distribute Schedule and Playlists on a group basis.
•All monitor sets initially come in Master mode.
Slave
•Play Schedule and Playlists distributed in Master mode.
•Remove monitor sets for their groups.
•Monitor sets that have been added to a group are automatically switched to Slave mode. Conversely, when a monitor set has been deleted
from a group, it is automatically initialized and switched to Master mode.
•If a new Slave has been added to an existing group, or if the Data Cloning or the distribution of schedule/Playlist has not been properly
performed, the Data Cloning or SYNCHRONIZE button will be activated.
•You can duplicate the master device’s setting data to the group by using Data Cloning.
•You can re-download the content distributed to the group by using SYNCHRONIZE.
GROUP MANAGEMENT
•Creating a New Group
1. Click Add New Group.
2. Enter a group name.
3. Click Add Device, select the devices you wish to add to the group, and add them.
4. Click Done, and you will see that a new group has been created.
•Editing a Group
1. Click the group you wish to edit.
2. Add a new device by using Add Device.
3. Delete a device by using Delete Device.
4. Check whether the devices in the group are connected to a network by using Device Check.
5. If there are any sets of devices in the group that are not Data Cloning or content synchronized, Data Cloning or SYNCHRONIZE button will
be activated.
6. You can re-copy the master device’s setting data to the group by using Data Cloning.
7. You can re-distribute the content distributed to the group by using SYNCHRONIZE.
•Deleting a Group
1. Click Delete Group.
2. Select the group you wish to delete and click Delete.
3. Check that the group you selected has been deleted.
•ALL DEVICES VIEW: All Devices View: This page enables you to manage all slave monitor sets that are connected to the same network.
1. Click All Devices View.
2. Click Reset Device Mode.
3. Select the slave monitor set whose device mode you wish to change and click Initializing.
ENGLISH
57
Setting Data Cloning
1 Select your desired group and click Clone.
2 Check that the data have been copied on the slave sets.
Content Distribution
1 Select the type of content you wish to distribute (Schedules or Playlists).
2 Select the content you wish to distribute.
3 Select the group to which you wish to distribute the content and click Distribute.
4 Run the Content Manager app on the slave sets and check that the content has been distributed.
* How to Use
•Monitor: Run, add, delete or edit app on the home screen.
•Mobile: Mobile devices: Run the app in the Launcher bar or access the app from a mobile device using the QR code or URL provided.
•You can create up to 25 groups.
•You can add up to 12 slave devices to a group.
•You can distribute the schedules stored on external devices after executing Content Manager’s import operation.
•Make sure to delete all schedules stored on the slave sets before distributing any schedules.
•A list of devices you can add to your desired group appears only when the following conditions have been met:
-The devices you wish to add must be on the same network as the master device.
-The devices you wish to add must be in Master mode, and they must not belong to any existing group.
-The UPnP feature must be enabled (go to General Network UPnP and set it to On).
•It may not work properly in wireless network environments. It is recommended you use a wired network.
•Run the initial settings for Slave function when deleting the group.
ENGLISH
58
IR Codes
•This feature is not available for all models.
Code
(Hexa) Function Note
08 (POWER) Remote control Button
(Power On/O)
95 Remote control Button
AF Remote control Button
0B Remote control Button
F0 Remote control Button
10-19
Number Key 0-9
Alphabet buttons
(Space)
Remote control Button
53 Remote control Button
1A Remote control Button
02 Remote control Button
03 Remote control Button
7C Remote control Button
B5 Remote control Button
09 Remote control Button
00
Remote control Button
01
Remote control Button
AB Remote control Button
0C Remote control Button
AA Remote control Button
40 Remote control Button
41 Remote control Button
Code
(Hexa) Function Note
07 Remote control Button
06 Remote control Button
44 Remote control Button
43 Remote control Button
28 (BACK) Remote control Button
5B Remote control Button
72 Remote control Button
71 Remote control Button
63 Remote control Button
61 Remote control Button
20 Remote control Button
21 Remote control Button
39 CC Remote control Button
B1 Remote control Button
B0 Remote control Button
BA Remote control Button
8F Remote control Button
8E Remote control Button
DC Remote control Button
9F Remote control Button
91 Remote control Button
E8 Remote control Button
ENGLISH
59
External control device Setup
RS-232C Setup
Connect the RS-232C (serial port) input jack to an external control
device (such as a computer or an A/V control system) to control the
product’s functions externally.
Connect the serial port of the control device to the RS-232C jack on the
product back panel.
•RS-232C connection cables are not supplied with the product.
RS-232C IN
(CONTROL & SERVICE)
(*Not Provided)
(Depending on model)
Phone jack Type
(Depending on model)
•You need to purchase the phone-jack to RS-232C cable required
for the connection between the PC and the TV, which is specied
in the manual.
* For other models, connect to the USB port.
* The connection interface may differ from your TV.
(PC)
USB IN
(TV)
(PC)
(PC)
RS-232C IN
(CONTROL & SERVICE)
(TV)
(TV)
(PC)
(TV)
SERVICE ONLY
RS-232C IN
(CONTROL & SERVICE)
RS-232C IN
(CONTROL & SERVICE)
1
3
2
4
1
3
2
4
(PC)
(TV)
Type of Connector : D-Sub 9-Pin
Male
6
15
9
No. Pin name
13.5 V
2RXD (Receive data)
3TXD (Transmit data)
4IR OUT from TV
5GND
6No Connection
7No Connection (5 V available in some models)
8No Connection
9 No Connection (12 V available in some models)
ENGLISH
60
RS-232C Congurations
7-Wire Configurations
(Standard RS-232C cable)
PC TV
RXD 2 3 TXD
TXD 3 2 RXD
GND 5 5 GND
DTR 4 6 DSR
DSR 6 4 DTR
RTS 7 8 CTS
CTS 8 7 RTS
D-Sub 9 D-Sub 9
3-Wire Configurations
(Not standard)
PC TV
RXD 2 3 TXD
TXD 3 2 RXD
GND 5 5 GND
DTR 4 6 DSR
DSR 6 4 DTR
RTS 7 8 RTS
CTS 8 7 CTS
D-Sub 9 D-Sub 9
Communication Parameters
•Baud rate: 9,600 bps (UART)
•Data length: 8 bits
•Parity : None
•Stop bit: 1 bit
•Communication code: ASCII code
•Use a crossed (reverse) cable.
IR OUT Using Guide
Suitable / Not Recommend remote-
controller data format
Item Formats
Suitable data
format NEC, RC5, Toshiba
Not recommend
data format
Continuous data format (short burst/gap
signal)
IR Receiver specications
Carrier frequency 37.9 KHz
Peak Wavelength 940 nm
Minimum burst
length Min. 300 us
Minimum gap time
is required of Min. 350 us
Data word length Max. 100 ms
Minimum gap time
in the data stream
is needed of
Min. 50 ms
Parameter Symbol Conditions Min Typ Max Unit
High Level
Out Pulse
Width
Twh Burst Wave
= 600 µs
Period =
1.2 ms
400 - 800 µs
Low Level
Out Pulse
Width
Twl 400 - 800 µs
•If not use the remote-controller with data formats
recommended, IR output signals will be suppressed
automatically by IR receiver.
•In this case, LG does not guarantee IR working function.
•To make sure of this matter, here are two methods as
below.
-Use the remote-controller with suitable data formats.
-Use the IR dongle receiver of the set-top box.
ENGLISH
61
Command Reference List
(Depending on model)
Command1 Command2 Data
(Hexadecimal)
01. Power k a 00 to 01
02. Aspect Ratio k c (See p. 62)
03. Screen Mute k d (See p. 62)
04. Volume
Mute k e 00 to 01
05. Volume
Control k f 00 to 64
06. Contrast k g 00 to 64
07. Brightness k h 00 to 64
08. Colour k i 00 to 64
09. Tint k j 00 to 64
10.
Sharpness k k 00 to 32
11.
OSD Select k l 00 to 01
12.
Remote
Control Lock
Mode
k m 00 to 01
13.
Balance k t 00 to 64
14.
Colour
Temperature x u 00 to 64
15.
Energy Saving j q (See p. 64)
16.
Auto
Configuration j u 01
17.
Equalizer j v (See p. 64)
18.
Tune
Command m a (See p. 64)
19.
Channel Skip/
Add m b 00 to 01
20.
Key m c (See p. 65)
21
Control
Backlight m g 00 to 64
22.
Input select x b (See p. 65)
•During USB operations such as DivX or EMF, all commands except
Power(ka) and Key(mc) are not executed and treated as NG.
Transmission / Receiving Protocol
(Depending on Model)
Transmission
[Command1][Command2][ ][Set ID][ ][Data][Cr]
[Command1] : First command to control the TV. (j, k, m or x)
[Command2] : Second command to control the TV.
[Set ID] : You can adjust the set ID to choose desired monitor ID number
in option menu. Adjustment range is 1 to 99. When selecting Set ID
‘0’, every connected set is controlled. Set ID is indicated as decimal (1
to 99) on menu and as Hexa decimal (0 x 0 to 0 x 63) on transmission/
receiving protocol.
[Data] : To transmit command data. Transmit ‘FF’ data to read status of
command.
[Cr] : Carriage Return
ASCII code ‘0 x 0D’
[ ] : ASCII code ‘space (0 x 20)’
OK Acknowledgement
[Command2][ ][Set ID][ ][OK][Data][x]
* The set transmits ACK (acknowledgement) based on this format
when receiving normal data. At this time, if the data is data read
mode, it indicates present status data. If the data is data write mode,
it returns the data of the PC computer.
Error Acknowledgement
[Command2][ ][Set ID][ ][NG][Data][x]
* The set transmits ACK (acknowledgement) based on this format
when receiving abnormal data from non-viable functions or commu-
nication errors.
Data 00 : Illegal Code
ENGLISH
62
1 Power (Command: k a)
►To control Power On/O of the set.
Transmission
[k][a][ ][Set ID][ ][Data][Cr]
Data 00 : Off
Data 01 : On
Ack
[a][ ][Set ID][ ][OK/NG][Data][x]
►To Show TV is Power On/O.
Transmission
[k][a][ ][Set ID][ ][FF][Cr]
Ack
[a][ ][Set ID][ ][OK/NG][Data][x]
* Similarly, if other functions transmit ‘0 x FF’ data based on this for-
mat, Acknowledgement data feed back presents status about each
function.
* OK Ack., Error Ack. and other message may display on the screen
when TV is power On.
2 Aspect Ratio (Command: k c) (Main Picture Size)
►To adjust the screen format. (Main picture format) You can also
adjust the screen format using the picture settings.
Transmission
[k][c][ ][Set ID][ ][Data][Cr]
Data 01 : 4:3 (Normal screen - Just Scan O)
Data 02 : 16:9 (Wide screen - Just Scan O)
Data 06 : Original (Just Scan O)
Data 09 : Just Scan
Ack
[c][ ][Set ID][ ][OK/NG][Data][x]
* Using the PC input, you select either 16:9 or 4:3 screen aspect ratio.
3 Screen Mute (Command: k d)
►To select screen mute on/o.
Transmission
[k][d][ ][Set ID][ ][Data][Cr]
Data 00 : Screen mute o (Picture on) / Video mute o
Data 01 : Screen mute on (Picture o)
Data 10 : Video mute on
Ack
[d][ ][Set ID][ ][OK/NG][Data][x]
* In case of video mute on only, TV will display On Screen Display
(OSD). But, in case of Screen mute on, TV will not display OSD.
4 Volume Mute (Command: k e)
►To control volume mute on/o.
You can also adjust mute using the mute button on remote control.
Transmission
[k][e][ ][Set ID][ ][Data][Cr]
Data 00 : Volume mute on (Volume o)
Data 01 : Volume mute o (Volume on)
Ack
[e][ ][Set ID][ ][OK/NG][Data][x]
5 Volume Control (Command: k f)
►To adjust volume.
You can also adjust volume with the volume buttons on remote
control.
Transmission
[k][f][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
* Refer to “Real data mapping”.
Ack
[f][ ][Set ID][ ][OK/NG][Data][x]
6 Contrast (Command: k g)
►To adjust screen contrast.
You can also adjust contrast in the picture settings.
Transmission
[k][g][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
* Refer to “Real data mapping”.
Ack
[g][ ][Set ID][ ][OK/NG][Data][x]
7 Brightness (Command: k h)
►To adjust screen brightness.
You can also adjust brightness in the picture settings.
Transmission
[k][h][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
* Refer to “Real data mapping”.
Ack
[h][ ][Set ID][ ][OK/NG][Data][x]
ENGLISH
63
8 Colour (Command: k i)
►To adjust the screen colour.
You can also adjust colour in the picture settings.
Transmission
[k][i][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
* Refer to “Real data mapping”.
Ack
[i][ ][Set ID][ ][OK/NG][Data][x]
9 Tint (Command: k j)
►To adjust the screen tint.
You can also adjust tint in the picture settings.
Transmission
[k][j][ ][Set ID][ ][Data][Cr]
Data Red : 00 to Green : 64
* Refer to “Real data mapping”.
Ack
[j][ ][Set ID][ ][OK/NG][Data][x]
10
Sharpness (Command: k k)
►To adjust the screen sharpness.
You can also adjust sharpness in the picture settings.
Transmission
[k][k][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 32
* Refer to “Real data mapping”.
Ack
[k][ ][Set ID][ ][OK/NG][Data][x]
11
OSD Select (Command: k l)
►To select OSD (On Screen Display) on/o when controlling remotely.
Transmission
[k][l][ ][Set ID][ ][Data][Cr]
Data 00 : Off
Data 01 : On
Ack
[l][ ][Set ID][ ][OK/NG][Data][x]
12
Remote Control Lock Mode (Command: k m)
►To lock the front panel controls on the monitor and remote control.
Transmission
[k][m][ ][Set ID][ ][Data][Cr]
Data 00 : Off
Data 01 : On
Ack
[m][ ][Set ID][ ][OK/NG][Data][x]
* If you are not using the remote control, use this mode. When main
power is on/off, external control lock is released.
* In the standby mode, if key lock is on, TV will not turn on by power
on key of IR & Local Key.
13
Balance (Command: k t)
►To adjust balance.
You can also adjust balance in the audio settings.
Transmission
[k][t][ ][Set ID][ ][Data][Cr]
Data L : 00 to R : 64
* Refer to “Real data mapping”.
Ack
[t][ ][Set ID][ ][OK/NG][Data][x]
14
Colour Temperature (Command: x u)
►To adjust Colour Temperature. You can also adjust Colour
Temperature in the picture settings.
Transmission
[x][u][ ][Set ID][ ][Data][Cr]
Data Warm: 00 to Cool:64
* Refer to “Real data mapping”.
Ack
[u][ ][Set ID][ ][OK/NG][Data][x]
ENGLISH
64
15
Energy Saving (Command: j q)
►To reduce the power consumption of the TV. You can also adjust
Energy Saving in picture settings.
Transmission
[j][q][ ][Set ID][ ][Data][Cr]
Power Saving
Function Level Description
7 6 5 4 3 2 1 0
0 0 0 0 Low
Power 0 0 0 0 Off
0 0 0 0 Low
Power 0 0 0 1 Minimum
0 0 0 0 Low
Power 0 0 1 0 Medium
0 0 0 0 Low
Power 0 0 1 1 Maximum
0 0 0 0 Low
Power 0 1 0 1 Screen Off
0 0 0 0 Low
Power 0 1 0 0 Auto
►‘Auto’ is available in TV that supports ‘Intelligent Sensor’.
Ack
[q][ ][Set ID][ ][OK/NG][Data][x]
16
Auto Configuration (Command: j u) (Only RGB support model)
►To adjust picture position and minimize image shaking
automatically. It works only in RGB (PC) mode.
Transmission
[j][u][ ][Set ID][ ][Data][Cr]
Data 01 : To set
Ack
[u][ ][Set ID][ ][OK/NG][Data][x]
17
Equalizer (Command : j v)
►To adjust equalizer.
Transmission
[j][v][ ][Set ID][ ][Data][Cr]
MSB LSB
0 0 0 0 0 0 0 0
Frequency Data
7 6 5 Frequency 4 3 2 1 0 Step
0 0 0 1st Band 0 0 0 0 0 0 (decimal)
0 0 1 2nd Band 0 0 0 0 1 1 (decimal)
0 1 0 3rd Band ... ... ... ... ... ...
0 1 1 4th Band 1 0 0 1 1 19 (decimal)
1 0 0 5th Band 1 0 1 0 0 20 (decimal)
Ack
[v][ ][Set ID][ ][OK/NG][Data][x]
18
Tune Command (Command: m a)
►Select channel to following physical number.
Transmission
[m][a][ ][Set ID][ ][Data 00][ ][Data 01][ ][Data 02][Cr]
Data 00 : High channel data
Data 01 : Low channel data
ex. No. 47 00 2F (2FH)
No. 394 01 8A (18AH),
DTV No. 0 Don’t care
Data 02 : [Antenna]
0 x 00 : Analogue Main
0 x 10 : DTV Main
0 x 20 : Radio
[Cable]
0 x 80 : Analogue Main
0 x 90 : DTV Main
0 x A0 : Radio
[Satellite]
0 x 40 : DTV Main
0 x 50 : Radio Main
Channel data range
Min : 00 Max : 270F (0 to 9999)
Ack
[a][ ][Set ID][ ][OK/NG][Data][x]
ENGLISH
65
19
Channel Skip/Add (Command: m b)
►To set skip status for the current Channel.
Transmission
[m][b][ ][Set ID][ ][Data][Cr]
Data 00 : Skip
Data 01 : Add
Ack
[b][ ][Set ID][ ][OK/NG][Data][x]
20
Key (Command: m c)
►To send IR remote key code.
Transmission
[m][c][ ][Set ID][ ][Data][Cr]
Data IR CODES
Ack
[c][ ][Set ID][ ][OK/NG][Data][x]
21
Control Backlight (Command: m g)
►To control the backlight.
Transmission
[m][g][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Ack
[g][ ][Set ID][ ][OK/NG][Data][x]
22
Input select (Command: x b) (Main Picture Input)
►To select input source for main picture.
Transmission
[x][b][ ][Set ID][ ][Data][Cr]
Data Structure
MSB LSB
0 0 0 0 0 0 0 0
External Input Input Number
External Input Data
0 0 0 0 DTV
0 0 0 1 Analogue
0 0 1 0 AV
0 1 0 0 Component
0 1 1 0 RGB
0 1 1 1
HDMI
1 0 0 0
1 0 0 1
1 0 1 0
Input Number Data
0 0 0 0 Input1
0 0 0 1 Input2
0 0 1 0 Input3
0 0 1 1 Input4
Ack
[b][ ][Set ID][ ][OK/NG][Data][x]
ENGLISH
66
* Real data mapping
00 : Step 0
A : Step 10 (Set ID 10)
F : Step 15 (Set ID 15)
10 : Step 16 (Set ID 16)
64 : Step 100
6E : Step 110
73 : Step 115
74 : Step 116
CF : Step 199
FE : Step 254
FF : Step 255
