Lindy 38247 User Manual
Displayed below is the user manual for 38247 by Lindy which is a product in the Matrix Switchers category. This manual has pages.
Related Manuals
© LINDY Group – THIRD EDITION (February 2019)
4x4 HDMI 2.0 18G Matrix Pro
User Manual English
Benutzerhandbuch Deutsch
Manuel Utilisateur Français
Manuale Italiano
No. 38247
lindy.com
Tested to comply with
FCC Standards
For Home and Office Use!
User Manual English
Introduction
Thank you for purchasing the 4x4 HDMI 2.0 18G Matrix with audio out. This product has been designed
to provide trouble free, reliable operation. It benefits from both a LINDY 2-year warranty and free lifetime
technical support. To ensure correct use, please read this manual carefully and retain it for future
reference.
Package Contents
▪ 4x4 HDMI 2.0 Matrix
▪ 5V DC 3A PSU including multi country adapters
▪ IR Extension cable
▪ IR Remote control including CR2025 3V battery
▪ Mounting brackets, screws & rubber feet
▪ RS-232 screw terminal
▪ Quick Install Guide
Features
▪ HDMI 2.0, HDCP 2.2, DVI 1.0 complaint
▪ Resolutions up to 4096x2160@60Hz 4:4:4 8bit
▪ Full 18G bandwidth
▪ Supports HDR10
▪ Supports 7.1 channel of LPCM, Dolby TrueHD and DTS-HD Master Audio digital audio signals
▪ RS232, IR remote control & IP control for switching
Specification
▪ Input Ports: 4 x HDMI (Female), RJ45 (Female), RS232 (Female), 3.5mm IR (Female), USB Micro B
(Female)
▪ Output Ports: 4 x HDMI (Female), 4 x SPDIF (Female)
▪ Power Supply: DC 5V
▪ Operating Temperature: -5°C - 45°C (23°F - 113°F)
▪ Storage Temperature: -20°C - 60°C (-4°F - 140°F)
▪ Relative Humidity: 20 ~ 90% RH (Non-condensing)
▪ Power Consumption: 13W max
Installation
Make sure all devices are switched off before making any connections.
Connect the source devices such as a PC, Blu-ray player or games console to the HDMI matrix input ports.
Then connect the high definition displays to the HDMI matrix output ports. When all the connections are
made, connect the power supply and switch on.
Once all the connections have been made, switch on the devices in this order: displays, HDMI Matrix,
source devices. Please allow a few minutes for the devices to handshake and for the signals to appear.
User Manual English
Operation
Front Panel
1. IR receiver window
2. Output Selector – Press the selector button to scroll through inputs 1-4
Rear Panel
1. SPDIF audio output ports
2. IR extension port
3. RS-232 connection port for control or upgrading the firmware
4. USB micro B port for upgrading the firmware
5. RJ45 port for IP control
6. DC power port
7. HDMI input ports
8. HDMI output ports
User Manual English
Remote Control
1. Power button
2. Output/Input buttons – select 1-4 output then 1-4 input to
display a single source to a single display
3. All button – select all then input 1-4 to display one input to
all outputs
4. Cancel button cancels the switching operation
5. PTP button – Mirror all inputs to outputs. E.g. input 1 to
output 1, input 2 to output 2……
RS-232 Pin Assignment
Matrix
Remote Control Console
Assignment
PIN
Assignment
1
NC
Tx
2
Rx
Rx
3
Tx
4
NC
GND
5
GND
6
NC
7
NC
8
NC
9
NC
User Manual English
Software Control
Download the latest version of the control software from the Lindy website.
Using either a RS232 cable or a USB cable, connect the matrix to a PC or laptop.
COM Setting – select and connect to the COM port on your PC
Device Name – You can rename the device using up to 16 characters
Port Set – Select and switch your input and output ports. Click status to display the current connection
status, click clear to clear the display information
EDID Config – Read and configure the EDID for each input
EDIDs are as followed
Audio EDID
7.1 Channel Audio supports: 24-bit, 192Khz, DTS Audio, Dolby Digital Plus, DTS HD, Dolby Digital and
Dolby TrueHD
5.1 Channel Audio supports: 24-bit, 192Khz, DTS Audio and Dolby Digital
2 Channel Audio supports: 16-bit, 48Khz. No audio formats
Video EDID
1080P "HDMI Matrix" 1920x1080P, 60Hz, 4:4:4, 8bit
4k2k@30Hz "HDMI Matrix" 3840x2160, 30Hz, 4:4;4, 8bit
4k2k@60Hz(YC4:2:0) "HDMI Matrix" 3840x2160, 60Hz, 4:2:0, 8bit
4k2k@60Hz(YC4:4:4) "HDMI Matrix" 3840x2160, 60Hz, 4:4:4, 8bit
User Manual English
IP Config – You can manually set the IP address and the MAC address, or you can set the router to
assign the IP automatically by clicking DHCP
Net Config – Allows you to configure the PC and the Matrix to be in the same LAN. Click “Net config” →
“Connect” → “Search Device” → “Sel Device Number” → “Connect” when you can see the device name,
it means connection was successful.
System Config – Power On/Off, reset or set default settings
User Manual English
Command Control
Open the application CommUart Assistant
Comport Setting
Baud Rate:
115200 bps
Parity:
None
Data Bits:
8 bit
Stop Bits:
1 bit
Enter the Command in the send options
Command
Function
Note
@W 04 00 01 02 03 #
PTP Function
Mirror all inputs and outputs
(Ex. Input 1 to output 1, input 2 to output 2, etc)
@W 50 #
Reboot
@W 51 #
Restore Factory Setting
@W 0F 00 #
Standby
00: Standby Mode
01: Cancel “Standby Mode”
E.g.: @W 00 00 #: Output 1 display Input1
Output 1 Input1
Command
Description
00
Output1
01
Output2
02
Output3
03
Output4
04
All Output
00
Input1
01
Input2
02
Input3
03
Input4
User Manual English
EDID Setting
@W XX AA BB #
Parameter Description:
XX for configuration of “INPUT EDID”
Command
05
06
07
08
Description
Input1
Input2
Input3
Input4
AA for selecting “Video Mode”
Command
00
01
02
03
Description
1080P
4K2K_30
4K2K_60(YC420)
4K2K_60(YC444)
BB for selecting below function
Bit7
Bit6
Bit5
Bit4
Bit3
Bit2
Bit1
Bit0
HDR
48Bit
36Bit
30Bit
7.1CH
5.1CH
2CH
3D
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
“1” : choose the function, “0” : doesn’t choose the function
Please note: HDR and 3D EDIDs are not supported
E.g. 01001000: 48Bit, 7.1CH
Change Binary code “01001000” to hexadecimal format “48”
E.g. @W 05 03 48 #
The EDID of input 1 is: 4K2K_60(YC444), 48Bit, 7.1CH
User Manual English
Web Control
The default IP address of the Matrix is 192.168.1.168. Your PC must be in the same IP range to allow
you access to it. For TCP/IP4 you can use and IP address in the range 192.168.1.2 to 192.168.1.254
excluding 192.168.1.168.
Open a web browser and enter the IP address 192.168.1.168
Port Page – Set your Input and Output ports
EDID Set Page – Edit the EDID settings for each input port
IP Config Page – Rename the device and enable/disable DHCP
CE/FCC Statement
CE Certification
This equipment complies with the requirements relating to Electromagnetic Compatibility Standards.
It has been manufactured under the scope of RoHS compliance.
CE Konformitätserklärung
Dieses Produkt entspricht den einschlägigen EMV Richtlinien der EU für IT-Equipment und darf nur
zusammen mit abgeschirmten Kabeln verwendet werden.
Diese Geräte wurden unter Berücksichtigung der RoHS Vorgaben hergestellt.
Die formelle Konformitätserklärung können wir Ihnen auf Anforderung zur Verfügung stellen
FCC Certification
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
You are cautioned that changes or modification not expressly approved by the party responsible for
compliance could void your authority to operate the equipment.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired
operation.
LINDY Herstellergarantie – Hinweis für Kunden in Deutschland
LINDY gewährt für dieses Produkt über die gesetzliche Regelung in Deutschland hinaus eine zweijährige Hersteller-
garantie ab Kaufdatum. Die detaillierten Bedingungen dieser Garantie finden Sie auf der LINDY Website aufgelistet
bei den AGBs.
Hersteller / Manufacturer (EU):.
LINDY-Elektronik GmbH LINDY Electronics Ltd
Markircher Str. 20 Sadler Forster Way
68229 Mannheim Stockton-on-Tees, TS17 9JY
Germany England
Email: info@lindy.com , T: +49 (0)621 470050 postmaster@lindy.co.uk , T: +44 (0)1642 754000
Recycling Information
WEEE (Waste of Electrical and Electronic Equipment),
Recycling of Electronic Products
Europe, United Kingdom
In 2006 the European Union introduced regulations (WEEE) for the collection and recycling of all waste electrical
and electronic equipment. It is no longer allowable to simply throw away electrical and electronic equipment. Instead,
these products must enter the recycling process.
Each individual EU member state has implemented the WEEE regulations into national law in slightly different ways.
Please follow your national law when you want to dispose of any electrical or electronic products. More details can
be obtained from your national WEEE recycling agency.
Germany / Deutschland Rücknahme Elektroschrott und Batterie-Entsorgung
Die Europäische Union hat mit der WEEE Direktive Regelungen für die Verschrottung und das Recycling von Elektro-
und Elektronikprodukten geschaffen. Diese wurden im Elektro- und Elektronikgerätegesetz – ElektroG in deutsches
Recht umgesetzt. Das Entsorgen von Elektro- und Elektronikgeräten über die Hausmülltonne ist verboten! Diese
Geräte müssen den Sammel- und Rückgabesystemen zugeführt werden! Dort werden sie kostenlos entgegen
genommen. Die Kosten für den weiteren Recyclingprozess übernehmen die Gerätehersteller.
LINDY bietet deutschen Endverbrauchern ein kostenloses Rücknahmesystem an, beachten Sie bitte, dass Batterien
und Akkus den Produkten vor der Rückgabe an das Rücknahmesystem entnommen werden müssen und über die
Sammel- und Rückgabesysteme für Batterien separat entsorgt werden müssen. Ausführliche Informationen zu
diesen Themen finden Sie stets aktuell auf der LINDY Webseite im Fußbereich.
France
En 2006, l'union Européenne a introduit la nouvelle réglementation (DEEE) pour le recyclage de tout équipement
électrique et électronique.
Chaque Etat membre de l’ Union Européenne a mis en application la nouvelle réglementation DEEE de manières
légèrement différentes. Veuillez suivre le décret d’application correspondant à l’élimination des déchets électriques
ou électroniques de votre pays.
Italy
Nel 2006 l’unione europea ha introdotto regolamentazioni (WEEE) per la raccolta e il riciclo di apparecchi elettrici ed
elettronici. Non è più consentito semplicemente gettare queste apparecchiature, devono essere riciclate. Ogni stato
membro dell’ EU ha tramutato le direttive WEEE in leggi statali in varie misure. Fare riferimento alle leggi del proprio
Stato quando si dispone di un apparecchio elettrico o elettronico.
Per ulteriori dettagli fare riferimento alla direttiva WEEE sul riciclaggio del proprio Stato.
No. 38247
3rd Edition, February 2019
lindy.com
Tested to comply with
FCC Standards
For Home and Office Use!