Table of Contents
Middle Atlantic Products 5-37 User Manual
Displayed below is the user manual for 5-37 by Middle Atlantic Products which is a product in the Rack Cabinets category. This manual has pages.
Related Manuals
Slim 5 SERIES
For 29, 37, 43 Rackspace Models Only
Instruction Sheet
I-0600 Rev M
UL
R
C US
LISTED
Thank you for purchasing the Slim 5 Series Rack. Please read all instructions thoroughly before
assembling this product.
THANK YOU
WARNING: Failure to read, understand and follow the following information can result in
serious personal injury, damage to the equipment or voiding of the warranty.
AVERTISSEMENT: Ne pas lire, comprendre et suivre les informations
suivantes peut entraîner des blessures graves, des dommages à l'équipement
ou de la nullité de la garantie.
Page 2
CAUTION: To avoid an unstable condition, place heavier components at the bottom of the
enclosure. When more than one component is placed in the enclosure, begin at the bottom
of the enclosure and place equipment at the lowest available point, evenly distribute weight
(horizontally) within the enclosure.
Component weight should be distributed as follows:
• 1/2 of the total component weight (at a minimum) placed in the bottom third of the cabinet
• 1/4 of the total component weight (at a maximum) placed in the middle third of the cabinet
• 1/4 of the total component weight (at a maximum) placed in the top third of the cabinet
ATTENTION: Pour éviter un état instable, placez composants les plus lourds au
fond de l'enceinte. Lorsque plus d'un composant est placé dans la enceinte,
commencer par le bas de l'enceinte et placer l'équipement à la point le plus bas
disponible, de distribuer uniformément le poids (horizontalement) dans le enceinte.
Le poids des composants devrait être réparti comme suit:
• 1/2 du poids total de la composante (au minimum) placé dans le tiers inférieur de l'armoire
• 1/4 du poids total de la composante (au maximum) placé dans le tiers médian de l'armoire
• 1/4 du poids total de la composante (au maximum) placé dans le tiers supérieur de l'armoire
IMPORTANT SAFETY INSTRUCTIONS / INSTRUCTIONS IMPORTAANTES SUR LA SÉCURITÉ
DANGER HAZARDOUS VOLTAGE/DANGER HAUTE TENSION
The lightning flash with the arrowhead symbol, within an equilateral
triangle is intended to alert the user to the presence of uninsulated
dangerous voltage within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
L'éclair avec le symbole de flèche dans un triangle équilatéral est
destiné à alerter l'utilisateur de la présence d'une tension dangereuse
non isolée dans l'enceinte du produit qui peut être d'une ampleur
suffisante pour constituer un risque de choc électrique pour les
personnes.
CAUTION/ATTENTION The exclamation point within an equilateral
triangle is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature
accompanying the appliance.
Le point d'exclamation dans un triangle équilatéral est destiné à
alerter l'utilisateur de la présence d'importants instructions d’opération
et de maintenance (entretien) dans la documentation accompagnant
l'appareil.
SAVE ALL INSTRUCTIONS / CONSERVER CES INSTRUCTIONS
CAUTION: All installation and assembly steps must be performed by qualified personnel.
ATTENTION: Toutes installation et de montage étapes doivent être effectuées par du
personnel qualifié.
CAUTION: Ensure that the floor has a structural load capacity that will support the weight of
the cabinet fully loaded with equipment.
ATTENTION: Veiller à ce que le sol a une capacité de charge structurelle qui supporter le
poids de le cabinet entièrement chargé avec l'équipement.
CAUTION: The following parts are not effectively bonded to the protective earth terminal:
Rack rails, lace bars, Lever Lock™, shelves, baffle, blanking panels, and cable management.
If any part needs to be bonded to the protective earth terminal it shall be done in accordance
with Article 250 of the National Electrical Code.
ATTENTION: Les pièces suivantes ne sont pas correctement liés à la borne de terre de
protection: rails de rack, des bars de dentelle, Lever Lock ™, des étagères, des chicanes,
des panneaux d'obturation, et la gestion des câbles. Si une partie doit être lié à la borne de
terre de protection, il doit être fait conformément à l'article 250 du Code national de l'électricité.
CAUTION: Power cord(s), for fans or other accessories, need to be secured to ensure that
they are routed away from pinch points and moving parts.
ATTENTION: Le cordon d'alimentation(s), pour les fans ou autres accessoires, doivent être
fixé à veiller à ce que ils sont acheminés loin des points de pincement et des pièces mobiles.
Page 3
IMPORTANT SAFETY INSTRUCTIONS / INSTRUCTIONS IMPORTAANTES SUR LA SÉCURITÉ
CAUTION: To reduce the risk of personal injury, these mounting instructions must be followed
and proper weight capacities must be observed.
ATTENTION: Pour réduire le risque de blessures, ces instructions de montage doivent être
respectées et les capacités de poids appropriées doivent être respectées.
WEIGHT RATINGS
Model Weight Rating
All 400 lbs.
CAUTION: Use caution when moving the cabinets with casters installed. There is a
possibility of tilting. Always move cabinet over smooth floor surfaces and a short distance
only. The enclosure should only be moved by pushing on the front or rear of the cabinet. DO
NOT push from the side.
ATTENTION: Soyez prudent lors du déplacement des armoires à roulettes installées. Il se
agit d'un possibilité de basculement. Toujours déplacer l'armoire sur les surfaces lisses et à
une courte distance seulement. L'enceinte ne doit être déplacé en poussant sur le devant ou
à l'arrière de l'armoire. FAIRE PAS pousser de côté.
CAUTION: Casters (if used) are not intended to support excessive cabinet loads for extended
periods of time. Please refer to caster base instruction sheet for recommended weight
capacity. Always use levelers to stabilize the cabinet after locating.
ATTENTION: Roulettes (le cas échéant) ne sont pas destinés à supporter des charges
excessives du Cabinet pour prolongée périodes de temps. Se il vous plaît se référer à
Caster feuille d'instructions de base pour poids recommandé la capacité. Toujours utiliser
niveleurs pour stabiliser l'armoire après avoir localisé.
CAUTION: Do not attempt to unload or move the enclosures alone. Make sure to have
sufficient amount of personnel and equipment to safely move this product.
ATTENTION: Ne essayez pas de décharger ou déplacer les enceintes seul. Assurez-vous
d'avoir quantité suffisante de personnel et de matériel pour déplacer ce produit en toute
sécurité.
Page 4
IMPORTANT SAFETY INSTRUCTIONS / INSTRUCTIONS IMPORTAANTES SUR LA SÉCURITÉ
Heights: 29, 37, and 43 RUs
Depths: 20” and 26”
Load Ratings: 400 lbs. load rating
Added Weight (Loading): Total added weight should be distributed as follows:
• 1/2 of the total added weight (at a minimum) placed in the bottom third of the enclosure
• 1/4 of the total added weight (at a maximum) palced in the middle third of the enclosure
• 1/4 of the total added weight (at a maximum) placed in the top third of the enclosure
• 9/16” Wrench
• 1/8” Balldrive Hex Key (Included)
Page 5
SPECIFICATIONS
SUPPLIED COMPONENTS AND HARDWARE
REQUIRED TOOLS
Rackrail Channels (x2 Left; x2 Right)
5/16-18 Flange
Nut (x20)
Top Panel Base Panel
#10 Nylon
Washer (x12)
10-32 x 5/8 Flat
Head Hex Screw (x4)
10-32 x 1/2 Flat
Head Hex Screw (x16)
Trim Panels (x2)
Braces (x2)
Page 6
ASSEMBLY
1. Attach the (4) rackrail channels to the top and base panels by passing (4) rackrail threads on each
rail through the panel holes and loosely screwing on the flange nuts. Do not tighten. (FIGURE A)
NOTE: Ensure cable knockouts on the top and bottom panels are facing the same side.
2. Attach (2) 10-32 X 1/2 hex screws to each corner of the front and rear of the top and base panels.
Firmly tighten the hex screws. (FIGURE B)
1/2” LENGTH
HEX SCREWS
FAN KNOCKOUTS
FOR TOP MOUNTED
FANS (PART# 5-FAN-K;
INCLUDES 2 FANS)
TOP
BOTTOM
TRIM PANEL
(TOP AND BOTTOM)
KNOCKOUTS
FRONT
REAR FLANGE NUT
RACKRAIL
FIGURE A
FIGURE B
Page 7
ASSEMBLY (CONTINUED)
4. Attach the (2) braces to the rackrail by passing mid-length rackrail threads through the brace holes
and loosely screwing on the flange nuts. Do not tighten. (FIGURE C)
5. Install squaring panels to the front and rear of the enclosure (approximately mid-height of the rack)
by tightening (4) Phillips head screws per panel. (FIGURE D)
NOTE: Squaring panels may be removed after some equipment is installed into the enclosure.
FIGURE C
FIGURE D
CABLE MANAGEMENT SLOTS
FOR NEATER AND MORE
EFFECTIVE CABLE MANAGEMENT.
BRACE
FLANGE NUT
FRONT
REAR
RACKRAIL
SQUARING PANELS
PHILLIPS HEAD SCREWS
REAR
FRONT
Page 8
ASSEMBLY (CONTINUED)
6. Lay the enclosure on a flat surface and tighten all of the flange nuts. Do not overtighten. (FIGURE E)
NOTE: The enclosure must be laid on a flat surface to prevent the assembled frame from going
cubically out of square.
7. Attach (2) trim panels to the front of the top and base panels using (4) 10-32 x 5/8 hex screws.
Do not overtighten. (FIGURE F)
FIGURE E
FIGURE F
GROUND PLANE
CORRECT INCORRECT
5/8” LENGTH
HEX SCREWS
TRIM PANEL
WARRANTY
Middle Atlantic Products, Inc. (the "Company") warrants the product to be free from defects in material or workmanship under normal use and conditions for the
lifetime of the product.
The Company's entire liability to the purchaser, and the purchaser's (or any other party's) sole and exclusive remedy, under this warranty shall be limited, at the Company's option, to
either (a) return of and refund of the price paid for, or (b) repair or replacement at the Company's factory of the products purchased, or any part or parts thereof, which the Company
has determined to be defective after inspection thereof at the Company's factory. This warranty does not cover damage due to acts of God,accident, misuse, abuse or negligence by
parties other than the Company, or any modification or alteration of the products. In addition, this warranty does not cover damage due to improper handling, assembly, installation or
maintenance.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL THE COMPANY BE LIABLE FOR ANY SPECIAL, INCIDENTAL, INDIRECT, OR
CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION OR ANY
OTHER PECUNIARY LOSS) ARISING OUT OF THE USE OF THE PRODUCTS PURCHASED, EVEN IF THE COMPANY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES. THE COMPANY'S LIABILITY TO THE PURCHASER (OR ANY OTHER PARTY) HEREUNDER, IF ANY, SHALL IN NO EVENT EXCEED THE PURCHASE PRICE OF
THE PRODUCTS PAID TO THE COMPANY.
Corporate Headquarters
Corporate Voice 973-839-1011 - Fax 973-839-1976 / International Voice +1 973-839-8821 - Fax +1 973-839-4982
middleatlantic.com - info@middleatlantic.com
Middle Atlantic Canada
Voice 613-836-2501 - Fax 613-836-2690 / middleatlantic.ca - contactcanada@middleatlantic.com
Factory Distribution
USA: NJ - CA - IL Canada: ON - BC
At Middle Atlantic Products we are always listening. Your comments are welcome.
Middle Atlantic Products is an ISO 9001 Registered Company.
Page 9
OPTIONS
The following Slim 5 options are available to complete your installation:
• Solid (DO-5-xx) and plexiglass (DOP-5-xx) front door
• Decorative (TSP-5-xx-yy, Top and Sides) and steel (SP-5-xx) side panels
• Rear access panels (RAPxx)
• Additional rackrail (5ARxx)
• Cable chase (5CCxx)
• Commercial grade casters (5W and 5WL) and caster bases (CBS-5 and CBS-5-26)
• Fine floor casters (5WR and 5WLR) and caster bases (CBS-5R and DBS-5-26R)
• Decorative trim panels (5-CAVTRIM and 5-BAVTRIM) and trim strips (TS, TA, and TC)
• Runner kit (5-RS20 and 5-RS26)
• Fan kit (5-FAN-K)
NOTE: See our catalog or visit www.middleatlantic.com for additional options.