Middle Atlantic Products DWRSR-ZL User Manual
Displayed below is the user manual for DWRSR-ZL by Middle Atlantic Products which is a product in the Rack Accessories category. This manual has pages.
Related Manuals
I-00142 Rev C
DWRSR-ZL
Zero Clearance Latch
Instruction Sheet
US Patent 7,188,570 B2
THANK YOU
Thank you for purchasing the DWRSR-ZL Zero Clearance Latch. Please read these instructions
thoroughly before installing this product.
PRODUCT FEATURES
- Allows for side-by-side and corner mounting of DWR and SR Series Racks
- Unique design saves valuable wall space
- Easy-to-use release latch can be locked from the front for added security
Page 2
ASSEMBLY
TOOLS REQUIRED:
- #2 Phillips Screwdriver
- 7/16" Wrench
- 11/32 Nut Driver or Socket
- Star-Post Wrench (Provided)
1) On the backpan, remove the existing key lock and lock clip. Save for later use. (FIGURE A)
2) Remove the two nuts on the inside of backpan and remove the latch. Discard parts indicated.
(FIGURE A)
BACKPAN
DISCARD LOCK CLIP (SAVE)
AFTER LOCK REMOVAL
INSTALL HOLE PLUG
KEY LOCK
(SAVE)
LATCH
DISCARD
DISCARD
FIGURE A
Page 3
INDEX ROD
L-Bracket
FIGURE B
Left Hand PivotRight Hand Pivot
3) On the backpan, install L-bracket using two 3/8"
long screws provided. (FIGURE B)
4) Determine the depth of the center section and
using the hardware provided, configure index
rods to the appropriate depth.
(FIGURE C for depths and orientation)
NOTE: Index rod / extension (if needed) should
pivot freely on rotary latch. Tighten nut, then back
off approximately 1/2 turn to allow free movement.
FIGURE C
17" Depth (11.5" deep center section)
Do not
overtighten
allow to pivot
freely
ROTARY
LATCH
INDEX ROD
28" Depth (22.5" deep center section)
17.75” EXTENSION
TIGHTEN
INDEX ROD
Do not
overtighten
allow to
pivot
freely
ROTARY
LATCH
22" Depth (16.5" deep center section)
Do not
overtighten
allow to
pivot
freely
ROTARY
LATCH
TIGHTEN
INDEX ROD
11.75" EXTENSION
32" Depth (26.5" deep center section)
Do not
overtighten
allow to
pivot
freely
ROTARY
LATCH TIGHTEN
17.75” EXTENSION
26" Depth (20.5" deep center section)
Do not
overtighten
allow to
pivot
freely
ROTARY
LATCH
INDEX ROD
TIGHTEN
11.75" EXTENSION
Page 4
FIGURE D
NOTE: Remove key when
installing cam
KEY
KEY LOCK
LOCK CLIP
(Orient As Shown)
INDEX ROD HOLE
TAB
(Oriented in
open position)
CAM
5) On the center section, determine the pivot side and remove the hole plug from the opposite side.
6) Install the key lock and lock clip removed in step 1. (FIGURE D)
NOTE: Loosen and slide the front rackrail back to ease the installation of the lock and cam.
7) Install the new cam provided in the hardware kit. The cam should face toward the index rod hole
when in the locked position, and toward the inside of the rack when in the unlocked position.
NOTE: Left hand pivot shown. Invert for right hand pivot.
Page 5
8) Install the index rod into the index rod hole. (FIGURE E)
9) Secure the rotary latch to the center section using the standoffs and security screws provided.
(FIGURE E)
NOTE: Left hand pivot installation shown. For the right hand pivot invert the latch assembly.
INDEX ROD HOLE
SECURITY
SCREWS
STANDOFFS
SECURITY
SCREWS
STANDOFFS
FIGURE E
INSIDE OF
CENTER
SECTION
Page 6
OPERATING INSTRUCTIONS
1) Pull the latch and rotate the center section out.
2) To close, rotate the center section until it latches onto the backpan.
Page 7
ZERO CLEARANCE LATCH DIMENSIONS
DWR SERIES
.25" min. distance required between DWR and wall
or other DWR using Zero Clearance Latch
64" (DWR-XX-17)
74" (DWR-XX-22)
82" (DWR-XX-26)
.25” minimum
distance
.57" min. distance required between SR and
wall or other SR using Zero Clearance Latch
.57" minimum
distance
SR SERIES
74.53" (SR-XX-22)
86.53" (SR-XX-28)
94.53" (SR-XX-32)
Page 8 30% Recycled Paper
WARRANTY
Middle Atlantic Products (the "Company") warrants the DWRSR-ZL Zero Clearance Latch to be free
from defects in material or workmanship under normal use and conditions for a period of (3) years
from date of shipment by the Company.
The Company's entire liability to the purchaser, and the purchaser's (or any other party's) sole and
exclusive remedy, under this warranty shall be limited, at the Company's option, to either (a) return of
and refund of the price paid for, or (b) repair or replacement at the Company's factory of the products
purchased, or any part or parts thereof, which the Company has determined to be defective after
inspection thereof at the Company's factory.
This warranty does not cover damage due to acts of God, accident, misuse, abuse or negligence by
parties other than the Company, or any modification or alteration of the products. In addition, this
warranty does not cover damage due to improper handling, assembly, installation or maintenance.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES OF ANY KIND, EITHER EXPRESSED OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE.
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL THE COMPANY
BE LIABLE FOR ANY SPECIAL, INCIDENTAL, INDIRECT, OR CONSEQUENTIAL DAMAGES
WHATSOEVER (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS PROFITS,
BUSINESS INTERRUPTION OR ANY OTHER PECUNIARY LOSS) ARISING OUT OF THE USE OF THE
PRODUCTS PURCHASED, EVEN IF THE COMPANY HAS BEEN ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. THE COMPANY'S LIABILITY TO THE PURCHASER (OR ANY OTHER PARTY)
HEREUNDER, IF ANY, SHALL IN NO EVENT EXCEED THE PURCHASE PRICE OF THE PRODUCTS
PAID TO THE COMPANY.
Corporate Headquarters
Corporate Voice 973-839-1011 - Fax 973-839-1976
International Voice +1 973-839-8821 - Fax +1 973-839-4982
middleatlantic.com - info@middleatlantic.com
Middle Atlantic Canada
Voice 613-836-2501 - Fax 613-836-2690
middleatlantic.ca - customerservicecanada@middleatlantic.ca
Factory Distribution
USA: NJ - CA - IL Canada: ON - BC
At Middle Atlantic Products we are always listening. Your comments are welcome.
Middle Atlantic Products is an ISO 9001 and ISO 14001 Registered Company.