Middle Atlantic Products LBFR-2036-T User Manual
Displayed below is the user manual for LBFR-2036-T by Middle Atlantic Products which is a product in the Rack Accessories category. This manual has pages.
Related Manuals
I-00130 Rev B
LBH / LBFR SERIES
Telescoping Lacer Bar
Instruction Sheet
THANK YOU
Thank you for purchasing the LBH / LBFR Series Telescoping Lacer bar.
Please read these instructions thoroughly before installing this product.
Page 2
TABLE OF CONTENTS
Hardware Pg. 2
Installing LBFR-5A-XX Pg. 3
Installing LBFR-XXXX-T Pg. 3
Installing LBH-1930-T Pg. 4
Applications Pg. 5-7
Warranty Pg. 7
HARDWARE
LBFR-5A-XX / LBFR-XXXX-T Includes:
Qty Description
8 5/16-18 flange nut
8 5/16-18 PEM stud
2 LBFR-5A-xx
or
2 LBFR-xxxx-T
LBH-1930-T Includes:
Qty Description
4 1/4-20 sliding nut
4 1/4-20 bolt
4 5/16-18 flange nut
4 5/16-18 PEM stud
2 LBH-1930-T
Page 3
INSTALLING LBFR-5A-XX
(SLIM 5 or AXS racks only)
1) Mount lacer bar in desired location to
inside of front and rear rackrail of SLIM 5
or AXS rack using included hardware.
(FIGURE A)
5/16-18
PEM STUD
5/16-18
FLANGE NUT LBFR-5A-XX
MOUNTS TO
INSIDE OF
RACKRAIL
FIGURE A
INSTALLING LBFR-XXXX-T
FRONT OF
RACK
5/16-18
FLANGE NUT
5/16-18
PEM STUD
LBFR-XXXX-T
MOUNTS TO
OUTSIDE OF
RACKRAIL
FIGURE B
HINT:
For stand-alone racks, it may be
easier to point studs into the rack
during installation.
1) Mount telescoping lacer bar in desired
location to outside of front and rear
adjustable rackrail using included hardware.
(FIGURE B)
HINT:
A) Telescoping lacer bars mount to the outside of rackrail
so there is no interference if center rackrail is required.
B) Telescoping lacer bars can also be mounted to center
rail and front or rear rackrail.
Page 4
FIGURE D
(Mounted flat)
INSTALLING LBH-1930-T
1) Horizontal lacer bars can be mounted flat or upright with
included hardware in the following configurations:
- Between rackrail brackets. (FIGURE C)
- Between LBFR Series front to rear lacer bars.
(FIGURE D)
- Between rackrail. (FIGURE E)
HINT:
When installing LBH-1930-T
onto rackrail in a SLIM 5 or AXS
Series rack, insert the PEM studs
through the rackrail so that they
point toward the inside of the
rack. Then install nuts.
1/4-20 SLIDING NUT
(SERRATED SIDE FACES OUT
FROM INSIDE OF BRACKET)
Install horizontal lacer bar onto
rackrail bracket using fixed holes
or the adjustable slot
1/4-20
BOLT
FIGURE C
(Mounted upright)
LBFR SERIES
LACER BAR
5/16-18
FLANGE NUT
5/16-18
PEM STUD
5/16-18
FLANGE NUT
5/16-18
PEM STUD
FIGURE E
(Mounted upright)
Page 5
APPLICATIONS
(For enhanced vertical and horizontal cable management capabilities)
LBFR-5A-XX allows for mounting of vertical lacer strips in racks that do not have rail brackets such as
SLIM 5, AXS & AX-SXR Series. (FIGURE F)
LBFR-5A-XX
LACE FIGURE F
LBFR-5A-XX allows for mounting of vertical power strips within racks that do not have rail brackets
such as SLIM 5, AXS & AX-SXR Series. (FIGURE G)
PDT-2015C-NS
LBFR-5A-XX
FIGURE G
Page 6
LBFR-5A & LBFR-XXXX-T allow for horizontal cable management from front to rear of the rack or
enclosure and vertically between lacer bars. (FIGURE H)
LBFR-5A-XX
LBFR-XXXX-T
FIGURE H
LBH-1930-T allows horizontal or vertical cable management by mounting to rackrail, rail brackets
and / or the LBFR-5A or LBFR-xxxx-T. (FIGURE J)
FIGURE J
LBFR-xxxx-T
LBH-1930-T
Page 7
WARRANTY
Middle Atlantic Products (the "Company") warrants the Telescoping Laver Bars to be free from defects in material or workmanship under normal use and conditions for the lifetime of the product.
The Company's entire liability to the purchaser, and the purchaser's (or any other party's) sole and exclusive remedy, under this warranty shall be limited, at the Company's option, to either (a) return of and
refund of the price paid for, or (b) repair or replacement at the Company's factory of the products purchased, or any part or parts thereof, which the Company has determined to be defective after inspection
thereof at the Company's factory.
This warranty does not cover damage due to acts of God, accident, misuse, abuse or negligence by parties other than the Company, or any modification or alteration of the products. In addition, this warranty
does not cover damage due to improper handling, assembly, installation or maintenance.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE.
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL THE COMPANY BE LIABLE FOR ANY SPECIAL, INCIDENTAL, INDIRECT, OR CONSEQUENTIAL DAMAGES
WHATSOEVER (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION OR ANY OTHER PECUNIARY LOSS) ARISING OUT OF THE USE
OF THE PRODUCTS PURCHASED, EVEN IF THE COMPANY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE COMPANY'S LIABILITY TO THE PURCHASER (OR ANY OTHER
PARTY) HEREUNDER, IF ANY, SHALL IN NO EVENT EXCEED THE PURCHASE PRICE OF THE PRODUCTS PAID TO THE COMPANY.
Corporate Headquarters Middle Atlantic Canada Factory Distribution
Corporate Voice 973-839-1011 - Fax 973-839-1976 Voice 613-836-2501 - Fax 613-836-2690 USA: NJ - CA - IL Canada: ON - BC
International Voice +1 973-839-8821 - Fax +1 973-839-4982 middleatlantic.ca - customerservicecanada@middleatlantic.ca
middleatlantic.com - info@middleatlantic.com
At Middle Atlantic Products we are always listening. Your comments are welcome. Middle Atlantic Products is an ISO 9001 and ISO 14001 Registered Company.
30% Recycled Paper
LBH-1930-T can be used as cable strain relief behind units when placed flat. (FIGURE K)
LBH-1930-T
FIGURE K