Middle Atlantic Products REB18 User Manual
Displayed below is the user manual for REB18 by Middle Atlantic Products which is a product in the Rack Accessories category. This manual has pages.
Related Manuals
I-00215 Rev B
REB SERIES
Rotating Sliding Base
Instruction Sheet
REB14
REB18
THANK YOU
Thank you for purchasing the REB Series Rotating Sliding Base. Please read these instructions
thoroughly before installing this product.
PRODUCT FEATURES
- Provides easy access to rear equipment connections and cables
- Locks closed to prevent unintentional opening
- Included accessories to manage cables and keep wires neat and organized
Page 2
Rotate this way only
Rotate this way only
PARTS
HOOK AND LOOP FASTENERS QTY
12
(each)
7/8” 7/8”
HOOK
(Coarse Material)
LOOP
(Soft Material)
#10x5/8 WOOD SCREWS QTY
6
#6x1/2 WOOD SCREW QTY
2
HOOK AND LOOP STRAP QTY
2
ADHESIVE BACKED CABLE MANAGERS QTY
2
WIRE TIE QTY
6
1"x2" LOOP FASTENER QTY
2
1”x2”
ROTATION LABEL QTY
1
(Right Rotation)
(Left Rotation)
Page 3
!!
Mounting surface MUST be able to support cantilever load, maximum load is 75 lbs.
SPECIFICATIONS
TOP VIEW
FRONT VIEW
REB14 12" [305mm]
REB18 16" [406mm]
REB14 14-1/8" [354mm]
REB18 18-1/8" [460mm]
17" [432mm]
15-3/8”
REB14 6-3/8" [162mm]
REB18 8-3/8" [213mm]
REB14 6-3/8" [162mm]
REB18 8-3/8" [213mm]
60º
ROTATION
REB14 28" [711mm]
REB18 35-7/8" [911mm]
FULLY EXTENDED
2" [51mm]
Recommended
cable clearance
between REB and
cabinet
1" [25mm]
MAXIMUM
SETBACK
4-3/8"
[111mm]
1-15/16"
[48mm]
REB14 1-15/16" [48mm]
REB18 4-5/8" [117mm]
SHOWN FULLY EXTENDED AND ROTATED 60º
CABLE CLEARANCE
17-1/16" [434mm]
2.12"
[54mm]
Page 4
1) Determine rotation direction (Default rotation is to the left). To switch rotation, turn over and move
Set Screw to opposite side. (FIGURE A)
INSTALLATION
SET SCREW SET SCREW
FIGURE A
LEFT
ROTATION
RIGHT
ROTATION
2) Place in desired location with Thumbscrews in secured position (This ensures a square
installation). Check clearance and setback for door closure, room for cables, etc.
3) If required, mark exposed mounting holes in the back of the rails and remove REB.
Drill pilot holes with 3/32" drill bit. (FIGURE B)
MOUNTING
HOLES
FIGURE B
THUMBSCREWS
Page 5
FIGURE E
FIGURE D
FIGURE C
4) Place REB back in desired location. Affix to surface using provided #10x5/8 Wood Screws.
(FIGURE C)
5) Loosen Thumbscrews and extend to next set of mounting holes. Install two #10x5/8
Wood Screws. If required, drill pilot holes using 3/32" drill bit. (FIGURE D)
6) Fully extend and install remaining 10x5/8 screws (six total screws, three per slide).
If required, drill pilot holes using 3/32" drill bit. (FIGURE E)
Page 6
FIGURE H
7) With REB fully extended, determine location of components.
8) Place components on base and verify clearance of knobs, doors, etc.
9) Remove components.
10) Turn the bottom component over.
11) Remove adhesive backing on 7/8" Loop Fastener.
12) Place Loop Fastener on solid portion of component's feet. If no feet are on the component,
place on flat locations as close to the corners as possible. (FIGURE F)
13) Attach 7/8" Hook Fastener to Loop Fastener. Remove backing. (FIGURE G) Hook and
Loop Fasteners ensure component(s) are secure on REB.
HOOK
FASTENER
LOOP
FASTENER
FIGURE F FIGURE G
14) Turn component over and place on predetermined location on the REB. Gently press down on
component to adhere. (FIGURE H)
15) Repeat steps 10-14, stacking components one on top of the other. (FIGURE J)
FIGURE J
Page 7
16) Connect all cables.
17) Route cabling to cabinet exit point.
18) Install 1"x2" Loop Fastener in appropriate location. Do not cover vents on component. (FIGURE J)
FIGURE J
LOOP
FASTENER
LEFT ROTATION RIGHT ROTATION
19) Wrap Hook and Loop Strap(s) around cables. Attach to 1"x2" rectangular Loop as shown.
(FIGURE K) A second Hook and Loop Strap and 1"x2" Loop Fastener are provided for cabling
needs. (Heavy cable bundles, etc.)
NOTE: When placing cabling in strap, keep cables as high as possible.
HOOK AND
LOOP STRAP
FIGURE K
Page 8
HOOK AND
LOOP STRAP
ADHESIVE BACKED CABLE MANAGERS
20) Using provided Wire Ties, bundle cabling approximately
every 6" to 8".
21) Remove backing from Adhesive Backed Cable Manager and
mount to highest possible location on the opposite side of
Hook and Loop Strap(s). (FIGURE L)
NOTE: If host enclosure allows, use provided #6x1/2 Wood Screws to
secure Adhesive Backed Cable Manager(s).
22) Install cabling to Adhesive Backed Cable Manager(s).
23) Open, rotate and close REB to ensure proper operation. Adjust
cabling if required.
24) Place Rotation Label on top component to show rotation direction.
25) Close REB and turn Thumbscrews to secure in place.
WARRANTY
Middle Atlantic Products (the "Company") warrants the REB Series Rotating Equipment base to be free from defects in material or
workmanship under normal use and conditions for a period of (3) three years from date of shipment by company.
The Company's entire liability to the purchaser, and the purchaser's (or any other party's) sole and exclusive remedy, under this warranty
shall be limited, at the Company's option, to either (a) return of and refund of the price paid for, or (b) repair or replacement at the
Company's factory of the products purchased, or any part or parts thereof, which the Company has determined to be defective after
inspection thereof at the Company's factory.
This warranty does not cover damage due to acts of God, accident, misuse, abuse or negligence by parties other than the Company, or
any modification or alteration of the products. In addition, this warranty does not cover damage due to improper handling, assembly,
installation or maintenance.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT
NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL THE COMPANY BE LIABLE FOR ANY
SPECIAL, INCIDENTAL, INDIRECT, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING, WITHOUT LIMITATION,
DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION OR ANY OTHER PECUNIARY LOSS) ARISING OUT OF
THE USE OF THE PRODUCTS PURCHASED, EVEN IF THE COMPANY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES. THE COMPANY'S LIABILITY TO THE PURCHASER (OR ANY OTHER PARTY) HEREUNDER, IF ANY, SHALL IN NO
EVENT EXCEED THE PURCHASE PRICE OF THE PRODUCTS PAID TO THE COMPANY.
Corporate Headquarters
Corporate Voice 973-839-1011 - Fax 973-839-1976 / International Voice +1 973-839-8821 - Fax +1 973-839-4982
middleatlantic.com - info@middleatlantic.com
Middle Atlantic Canada
Voice 613-836-2501 - Fax 613-836-2690 / middleatlantic.ca - customerservicecanada@middleatlantic.ca
Factory Distribution
USA: NJ - CA - IL Canada: ON - BC
At Middle Atlantic Products we are always listening. Your comments are welcome.
Middle Atlantic Products is an ISO 9001 and ISO 14001 Registered Company.
FIGURE L