Table of Contents
Middle Atlantic Products SRCC User Manual
Displayed below is the user manual for SRCC by Middle Atlantic Products which is a product in the Rack Accessories category. This manual has pages.
Related Manuals
I-0900 Rev J
SRS SERIES
Assembly Instructions
Instruction Sheet
THANK YOU
Thank you for purchasing the SRS Series. Please read these instructions
thoroughly before installing/assembling this product.
Page 2
12 MOUNTING
HOLES
BOTTOM
PAN
LOCKING
PANEL
SQUARING
PANEL
1) Position and center SRS in millwork with setback
desired.
2) Using 2 preliminary mounting hole locations attach
the SRS to the millwork.
PRELIMINARY
MOUNTING
HOLES
3) Remove "Locking Panel" and slide rack out
4) Secure SRS using 12 mounting points indicated
in drawing.
(4x)
(4x)
(4x)
5) Attach rackrail to the sliding section using hardware
provided, finger tighten only.
6) Install squaring panel approximately 1/3 of the way
down from the top of the rackrail using hardware
provided. NOTE: The squaring panel remains in place
until some of the equipment is loaded.
7) Final tighten the rackrail to the sliding section.
8) Test the sliding carriage operation. Adjust mounting
positions as necessary should interference with the
millwork occur.
9) Attach the Locking panel.
10) Rail Stops serve to maintain a plumb position when rack
is closed. Mount 2 stops per side in the highest position
possible while maintaining contact with the backside of
the rackrail in the closed position. Wood screws are
for this provided attachment. (see illustration above)
RAIL STOPS
(stack 2 per side)
NOTE: If optional cable carrier
is used it must be
installed prior to rackrail.
(See PAGE 2)
Page 3
OPTIONAL
SRS Cable Carrier Instructions
1) Attach the Hinge Mounting Plate
to the rear surface of the SRS bottom
pan with four 10-32 socket head screws.
2) Attach the Cable Carrier Hinge to the
rear of the Hinge Mounting Panel with
four 10-32 socket head screws.
3) Attach front of Cable Carrier to the
SRS Chassis with four 10-32 socket
head screws
NOTE: Carefully examine drawing
for details of which side hinge
mounting panel goes to
BOTTOM PAN HINGE MOUNTING
PLATE
SRS REAR RAILS
SRS Series rough-in pan
mounting point locations
3x 18.125
3x 12.125
4x 17.34
18.69
15.95
11.0
8.0
.000
(from trim)
9.55
19.09
FRONT
4x 13.97
2.95
4x 1.59
3.95
(only mounting holes shown)
Page 4 30% Recycled Paper
WARRANTY
Middle Atlantic Products, Inc. (the "Company") warrants the SRS Series to be free from defects in material or workmanship under normal use and conditions for a period of
(3) three years from date of shipment by the Company.
The Company's entire liability to the purchaser, and the purchaser's (or any other party's) sole and exclusive remedy, under this warranty shall be limited, at the Company's option, to
either (a) return of and refund of the price paid for, or (b) repair or replacement at the Company's factory of the products purchased, or any part or parts thereof, which the Company
has determined to be defective after inspection thereof at the Company's factory. This warranty does not cover damage due to acts of God,accident, misuse, abuse or negligence by
parties other than the Company, or any modification or alteration of the products. In addition, this warranty does not cover damage due to improper handling, assembly, installation or
maintenance.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL THE COMPANY BE LIABLE FOR ANY SPECIAL, INCIDENTAL, INDIRECT, OR
CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION OR ANY
OTHER PECUNIARY LOSS) ARISING OUT OF THE USE OF THE PRODUCTS PURCHASED, EVEN IF THE COMPANY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES. THE COMPANY'S LIABILITY TO THE PURCHASER (OR ANY OTHER PARTY) HEREUNDER, IF ANY, SHALL IN NO EVENT EXCEED THE PURCHASE PRICE OF
THE PRODUCTS PAID TO THE COMPANY.
Corporate Headquarters
Corporate Voice 973-839-1011 - Fax 973-839-1976 / International Voice +1 973-839-8821 - Fax +1 973-839-4982
middleatlantic.com - info@middleatlantic.com
Middle Atlantic Canada
Voice 613-836-2501 - Fax 613-836-2690 / middleatlantic.ca - customerservicecanada@middleatlantic.ca
Factory Distribution
USA: NJ - CA - IL Canada: ON - BC
At Middle Atlantic Products we are always listening. Your comments are welcome.
Middle Atlantic Products is an ISO 9001 Registered Company.