Motorola C1003LB+ User Manual
Displayed below is the user manual for C1003LB+ by Motorola which is a product in the Telephones category. This manual has pages.
Related Manuals
Manufactured, distributed or sold by Suncorp Technologies Ltd., oicial licensee
for this product. MOTOROLA and the Stylized M Logo are trademarks or registered
trademarks of Motorola Trademark Holdings, LLC. and are used under license. All
other trademarks are the property of their respective owners. © 2014 Motorola
Mobility LLC. All rights reserved.
Version 4 (SG)
Welcome...
to your new Motorola C1LB+ Digital Cordless Telephone!
• All handsets are fully cordless for locating anywhere within range.
• 50 Name and Number phonebook.
• Bright backlit display.
• Speakerphone for hands-free conversations.
• Caller ID shows you who’s calling and see details of the last 40 callers in a Calls list.1
• Redial up to 10 of the last numbers called.
• Register up to 5 handsets to a single base and register each handset with up to 4 dierent
bases.
• Make internal calls and transfer external calls between handsets.
• Choose from 10 dierent ringtones for internal and external calls as well as numbers stored in
the phonebook.
Please note that this equipment is not designed for making emergency telephone calls when
the power fails. Alternative arrangements should be made for access to emergency services.
Need help?
If you have any problems setting up or using your C1LB+, please contact Customer Services
on (65) 68412668. Email: support@alcom.com.sg.
Alternatively, you may nd the answer in the ‘Help’ section at the back of this guide.
1You must subscribe to your network provider’s Caller ID or Call Waiting service for these
features to work. A subscription fee may be payable.
This user guide provides you with all the information you need to get
the most from your phone.
To set up your phone, follow the simple instructions in ‘Getting
Started’, on the next few pages.
IMPORTANT
Only use the telephone line cord supplied.
Got everything?
• C1LB+ base & cordless handset
• 2 x rechargeable Ni-MH battery cells
• Power adaptor for the base
• Telephone line cord
If you have purchased a C1LB+ multiple pack you will also have the following additional
items:
• Cordless handset & charger
• 2 x rechargeable Ni-MH battery cells
• Power adaptor for the charger
ECOMOTO: a convergence of eorts by marketing, design, research, engineering and
supply chain management that leads to better products for everyone. A holistic view that
focuses on both social and environmental responsibility. A passion and a shared point of view.
The right thing to do.
• Meets and / or exceeds EMEA environmental regulatory requirements.
• Eco friendly packaging with a minimum 20% post consumer recycled content.
• Phone housing is built with a minimum of 25% post consumer recycled content plastic.
• Energy eicient charger that meets EU Code of Conduct requirements.
• ECO mode function which reduces the transmitted power and energy consumption.
2. Getting to know your phone
Overview of your handset
BATTERY PERFORMANCE
In ideal conditions, fully charged batteries should give up to 6.5 hours talk time or up to 135 hours
standby time on a single charge.1
Note that new batteries do not reach their full capacity until they have been put to normal use for
several days.
To keep your batteries in the best condition, leave the handset o the base for a few hours at a
time.
Running the batteries right down at least once a week will help them last as long as possible.
The charge capacity of rechargeable batteries will reduce with time as they wear out, giving the
handset less talk / standby time. Eventually they will need to be replaced.
After charging your handset for the rst time, subsequent charging time is about 6–8 hours a day.
Batteries and handset may become warm during charging. This is normal.
1All talk and standby times are approximate and depend on features selected and usage
pattern.
Date and time
If you have subscribed to a Caller ID Service, the date and time is set automatically for all handsets
when you receive your rst call.
If you do not have a Caller ID service, you can set the date and time manually, see section “7.
Clock & Alarm”.
Your C1LB+ is now ready for use.
Installing and charging the handset
1. Remove the battery cover from the back of the handset and insert the rechargeable Ni-MH
battery cells supplied. Please note the ’+’ and ’-’ markings inside the battery compartment
and insert in the correct direction.
2. Slide the battery cover back into place.
3. If you are charging the batteries for the rst time, place the handset on the base to charge for
at least 24 hours continuously.
4. When the handset is fully charged, icon will appear steady on the display. Plug the other
end of the telephone line cord (make sure that one end is already plugged into the base) into
the telephone wall socket.
Connecting the handset and charger
(for multi-pack only)
If you have purchased a multiple pack, you will need to carry out this process for all the handsets
and chargers.
1. Plug the power adaptor into the socket marked on the underside of the charger and plug
the other end into the mains power wall socket.
2. Remove the battery cover from the back of the handset and insert the 2 x AAA NiMH
rechargeable batteries supplied. Please note the ’+’ and ’-’ markings inside the battery
compartment and insert in the correct direction.
3. Slide the battery cover back into place.
If you are charging the batteries for the rst time, place the handset on the charger to charge for
at least 24 hours continuously.
4. When the handset is fully charged, icon will appear steady on the display. The display will
show
HANDSET
and handset number (e.g. 2) to indicate that it is registered to the base.
IMPORTANT
Warning! Use only the approved rechargeable Ni-MH battery cells (2 x AAA Ni-MH 300mA
rechargeable batteries) supplied with your C1LB+.
Please do not use alkaline or non rechargeable batteries. It may cause permanent damage to
the product and void the warranty.
BATTERY LOW WARNING
If icon flashes on the display and you hear a warning beep every minute during a call, you
will need to recharge the handset before you can use it again.
When charging, icon will scroll on the display. Once fully charged scrolling will stop.
1. Getting started
IMPORTANT
Do not place your C1LB+ in the bathroom or other humid areas.
Location
You need to place your C1LB+ base within 1.5 metres of the mains power and telephone wall
socket so that the cables will reach. The socket-outlet should be installed near the equipment and
should be easily accessible.
Make sure that it is at least 1 metre away from other electrical appliances to avoid interference.
Your C1LB+ works by sending radio signals between the handset and base. The strength of the
signal depends on where you place the base. Placing it as high as possible ensures the best
signal.
HANDSET RANGE
The unit has a range of up to 300 metres outdoors when there is a clear line of sight between
the base and handset. Any obstruction between the base and handset will reduce the range
signicantly. With the base indoors and the handset either indoors or outdoors, the range will
normally be up to 50 metres. Thick concrete and stone walls can severely aect the range.
SIGNAL STRENGTH
The icon on your handset indicates that you are within range of the base. When out of range
of the base, the icon flashes. If you are on a call, you will hear a warning beep.
The line will hang up if the handset moves out of range of the base. Move closer to the base. The
handset will automatically reconnect to the base.
Setting up
IMPORTANT
The base station must be plugged into the mains power at all times. Do not connect the
telephone line cord into the wall socket until the handset is fully charged. Use only the power
adaptor and telephone line cord supplied with the product.
Connecting the base
1. Plug the telephone line cord into the socket marked on the underside of the base.
2. Plug the power adaptor into the socket marked on the underside of the base and plug the
other end into the mains power wall socket. Switch on the mains power.
Handset LCD Display
Flashes to indicate an incoming external call.
External call in progress.
Flashes to indicate an incoming internal call.
Internal call in progress.
3-way call in progress or transfer an external call to another C1LB+ handset registered to the
base.
Eco mode is ON.
Flashes to indicate new voicemail messages received. O when you have no voicemail
messages.1
Indicates signal strength.
Flashes when handset is not registered to the base or if you go out of range.
Hands-free mode is ON.
Menu is opened.
Phonebook is opened.
Flashes to indicate new calls list entries received.2
Answered call (when viewing the Calls list).2
Unanswered call (when viewing the Calls list).2
Keypad is locked.
Displayed number is longer than 12 digits.
The approximate power levels of your battery are indicated as follows:
Battery is fully charged.
Battery is partially charged.
Battery is running low.
Flashes when battery is almost fully discharged.
1This feature is dependent on your Network Service provider supporting the service. A
subscription fee may be payable.
2For this feature to work, you must subscribe to Caller ID Service from your network operator. A
subscription fee may be payable.
Underside of the base
A
A Page
In standby mode, press to ring the handset(s).
Press and hold to enter registration mode when registering handsets.
Navigating the menus
Your C1LB+ has an easy to use menu system.
Each menu has a list of options, which you can see on the menu map on the following page.
When the handset is switched on and in standby:
1. Press m to open the main menu.
2. Then use u or d buttons to scroll through the available options.
3. Press m to select an option. To return to the previous menu level, press p . To exit the
menu and return to standby, press n.
NOTE
If no buttons are pressed for 20 seconds, the handset returns to standby automatically.
Menu map
PHONEBOOK HANDSET DATE -- TIME
ADD ENTRY BEEP DATE SET
MODIFY ENTRY INT RING VOL CLOCK SET
DELETE ENTRY EXT RING VOL ALARM SET
SETUP INT MELODY REGISTER
DEL HANDSET EXT MELODY SELECT BASE
PIN CODE AUTO ANSWER REG BASE
DIAL MODE NAME
RECALL LANGUAGE
DEFAULT KEYLOCK ?
ECO MODE
3. Using the phone
NOTE
Your handset will automatically time the duration of all external calls. The call timer will display
after the rst 15 seconds of your call. When the call ends, the total duration of your talk time is
shown for 5 seconds.
3.1 Switch the handset on / o
Press and hold n to switch the handset on or o.
3.2 Calls
3.2.1 Make a call
1. Press t.
2. When you hear the dial tone, dial the number.
3.2.2 Preparatory dialling
1. Dial the number rst. If you make a mistake press p to delete the last digit.
2. Press t to dial.
3.2.3 End a call
Press n, or place the handset back on the base or charger.
3.2.4 Receive a call
When you receive an external call, the phone rings and icon flashes on the display.
1. If the handset is o the base then press t to answer the call, or if the handset is on the base
simply lift the handset to answer the call.
NOTE
If you prefer to press t when you lift up the handset to answer a call, you will need to switch
Auto answer o.
3.3 Adjust the earpiece volume
During a call, press u or d to increase or decrease the volume. There are 5 levels to choose
from.
3.4 Mute
You can mute your handset so that you can talk to someone nearby without your caller hearing.
1. During a call, press m. The display shows
MUTE
and your caller cannot hear you.
2. Press m again to resume your call.
3.5 Intercom
3.5.1 Make an internal call
If you have more than one handset registered to the base, you can make internal calls between
two handsets.
icon is displayed to indicate an internal call.
1. Press I followed by the number (1-5) of the handset you want to call.
3.5.2 Receive an internal call
When you receive an internal call, icon flashes and the handset number that is calling you is
displayed.
1. Press t to answer the call.
3.5.3 Transfer a call
You can transfer an external call to another handset registered to the base.
During an external call:
1. Press I followed by the handset number (1-5) that you want to transfer to.
2. When the other handset answers, press n to complete the transfer.
NOTE
If there is no answer from the other handset and you wish to return to your external caller,
press I.
Your external call resumes automatically after 30 seconds if there is no answer.
3.5.4 3-way conference call
You can hold a 3-way conference call between 2 internal callers and 1 external caller.
During a call with an external caller:
1. Press followed by the handset number (1-5) that you want to establish a conference call.
Enter the rst letter of the name to search alphabetically.
The rst name that starts with this letter or the nearest letter in the alphabet will be displayed.
Scroll u or d to the entry you want.
3. Press t to dial or n to return to standby.
NOTE
When the name is displayed, you can switch between the name and number by pressing m.
4.3 Edit a name and number
1. Press m. The display shows
PHONEBOOK
.
2. Press m. The display shows
ADD ENTRY
.
3. Scroll d to
MODIFY ENTRY
and press m.
4. Scroll u or d to the entry you want to edit, or search alphabetically and press m. The
existing name is displayed.
5. Press p to delete the name if required, then enter the new name and press m. The
existing number is displayed.
6. Press p to delete the number if required, then enter the new number and press m.
7. Scroll u or d to select a new ringer melody and press m. The display shows
ADD ENTRY
.
8. Enter the next name and number entry you wish to store in your phonebook or press p
twice to return to standby.
4.4 Delete an entry
1. Press m. The display shows
PHONEBOOK
.
2. Press m. The display shows
ADD ENTRY
.
3. Scroll d to
DELETE ENTRY
and press m.
4. Scroll u or d to the entry you want to delete, or search alphabetically and press m. The
display shows
CONFIRM ?
.
5. Press m to conrm or p to cancel.
5. Handset settings
5.1 Handset ringer volume
You can adjust the ringer volume and set dierent volume levels for your internal and external
calls. Choose from 5 volume levels or O.
1. Press m, scroll d to
HANDSET
and press m.
2. Press u or d to select
INT RING VOL
or
EXT RING VOL
and press m.
3. Press u or d to select the volume (1 -5 or OFF) .
4.1 Store a name and number
If the C1LB+ is connected to a switchboard, you may need to enter a pause in a stored number.
This gives the switchboard time to nd an outside line.
A pause is normally stored after the switchboard access code (e.g. 9).
When storing a number, press and hold # until the display shows P. You can then continue
storing the phone number.
If you have subscribed to Caller ID Service and wish to display the name of your caller instead of
the number, save the full telephone number including the area code to your phonebook.
You can store multiple entries with the same number. However, to prevent unnecessary
duplicated entries, you can only store the same name once.
1. Press m. The display shows
PHONEBOOK
.
2. Press m. The display shows
ADD ENTRY
.
3. Press m. The display shows
NAME ?
.
4. Enter the name and press m. The display shows
NUMBER ?
.
5. Enter the number and press m. The display shows
MELODY 1
.
6. Press u or d to select the ringer melody you want and press m.
The display shows
ADD ENTRY
.
7. Enter the next name and number entry that you wish to store in your phonebook or press
p twice to return to standby.
ENTERING NAMES
Use the keypad letters to enter names, e.g. to store TOM:
Press 8 once to enter T.
Press 6 three times to enter O.
Press 6 once to enter M.
WRITING TIPS
Press p to delete the last character or digit.
Press u or d to move between characters.
Press 1 to insert a space.
Use 1 twice to insert a dash.
4.2 View or dial an entry
1. Press p.
icon is displayed.
2. Scroll u or d to the entry you want.
OR
3. Press m. The display shows
ADD ?
.
4. Press m again. The display shows
NAME ?
.
5. Enter the name and press m. The number is displayed.
6. Edit the number if necessary, then press m.
7. Press u or d to select the ringer melody you want and press m.
The number is stored.
3.7.3 Delete an entry
1. Press r to open the Redial list.
2. Scroll u or d to the entry you want and press p. The display shows
DELETE ?
.
3. Press m to conrm or p to cancel.
3.74 Delete the entire Redial list
1. Press r to open the Redial list.
2. Press and hold p. The display shows
DELETE ALL ?
.
3. Press m to conrm or to cancel.
3.8 Lock / unlock the keypad
You can lock the keypad so that it cannot be operated accidentally while carrying it around.
NOTE
When the keypad is locked, you can still answer incoming calls and operate the handset as
normal during the call. When the call ends, the keypad lock comes on again.
1. Press and hold *.
icon is displayed.
2. To unlock the keypad, press any key on your handset. The display shows
PRESS *
.
3. Press * within 5 seconds.
3.9 Paging / Find handset
You can alert a handset user that they are wanted or locate a missing handset.
Paging calls cannot be answered by a handset.
1. Press on the base. All handsets registered to the base will ring.
2. To stop the ringing, press on the base again or press any button on the handset.
4. Phonebook
You can store up to 50 names and numbers in the phonebook. Names can be up to 12 characters
long and numbers up to 24 digits. You can also select dierent ringer melodies for the phonebook
entries.
2. When the other handset answers, press # to connect all three callers to begin the
conference call. icon is displayed.
3. If there is no answer from the other handset, press I to return to your external caller.
4. Press n to end the call.
3.6 Hands-free speakerphone
Hands-free lets you talk to your caller without holding the handset. It also enables other people in
the room to listen to the conversation over the loudspeaker.
3.6.1 Make a hands-free call
1. Dial the number and then press t twice.
icon is displayed and you will hear the call over the handset loudspeaker.
2. Press t to switch the call between the earpiece and the loudspeaker.
3. Press n to end the call.
NOTE
During a hands-free call, press u or d to adjust the volume.
3.6.2 Answer a call hands-free
If the handset is on the base and auto answer is switched on, lift the handset and press t.
If the handset is o the base or auto answer is switched o, press t twice to answer the call.
3.6.3 Switch to hands-free during a call
During a call, press t to put the call on the loudspeaker.
To switch hands-free o and return the call to the earpiece, press t again.
3.7 Redial
The last 10 entries dialled are stored in the redial list.
3.7.1 View or dial an entry
1. Press r to open the Redial list.
2. Scroll u or d to the entry you want.
3. Press t to dial the displayed entry or press n to return to standby.
NOTE
If the caller’s number exactly matches an entry stored in the phonebook, the name is displayed.
Press m to see the caller’s number.
3.7.2 Copy a Redial list number to the phonebook
1. Press r to open the Redial list.
2. Scroll u or d to the entry you want.
Warning: Charge the handset for 24 hours before use.
Motorola C1LB+
For C1001LB+, C1002LB+, C1003LB+ and C1004LB+
Digital Cordless Telephone
Earpiece
Display
Up
During a call, press to increase
earpiece volume.
When the phone is ringing,
press to increase the handset
ringer volume.
Press to scroll through the
menu options, redial list, calls
list and phonebook entries.
Menu / OK / Mute
Press to open the Menu.
Press to select menu
options and to conrm a
displayed option.
During a call, press to turn
mute on / o.
Talk / Hands-free
Press to make and receive
calls.
Press to switch hands-free
on or o during a call.
Keypad lock / * / Switch
from Pulse to Tone
Press and hold to lock the
keypad.
To unlock, press any key
and follow the on screen
instructions.
Dial a *.
During a call, press and
hold to switch from pulse
dialling to
tone dialling.
Recall
Use with switchboard / PABX
services and some network services.
When on an external call, press
Recall to get a fresh dialling tone or
to access call waiting when you hear
the signal. Press the key again to
toggle between your two callers.
Redial
In standby mode,
press to open the
redial list.
Phonebook / Delete / Back
In standby mode, press to open
the phonebook menu.
In editing mode, press to delete
characters and digits.
Go back to the previous menu
level.
Calls list / Down
In standby mode, press to open
the calls list.
During a call, press to decrease
earpiece volume.
When the phone is ringing, press
to decrease the handset ringer
volume.
Press to scroll through the menu
options, redial list, calls list and
phonebook entries.
End Call / Exit / Switch Handset
on / o
Press to end a call.
When viewing the redial / calls
list / phonebook or when in the
menu, press to exit and return to
standby.
Press and hold for 3 seconds to
switch the handset on / o.
Pause / #
Press and hold to enter a
pause (P) when pre-dialling
or storing numbers.
Dial a #.
Intercom
Used to make internal calls
and transfer calls to other
C1LB+ handsets registered
to the base.
Microphone
Battery
status
Scrolls
when
charging
Time or Handset name
In standby mode, press and hold to switch handset
0
idle screen between handset name or time.
Eco mode
Circle around
appears when
Eco mode is ON
How to Obtain Warranty Service or Other Information?
To obtain service or information, please call: (65) 68412668. Email: support@alcom.com.sg.
You will receive instructions on how to ship the Products or Accessories at your expense and risk,
to a SUNCORP Authorized Repair Center.
To obtain service, you must include: (a) the Product or Accessory; (b) the original proof of
purchase (receipt) which includes the date, place and seller of the Product; (c) if a warranty card
was included in your box, a completed warranty card showing the serial number of the Product;
(d) a written description of the problem; and, most importantly; (e) your address and telephone
number.
Technical Information
How many telephones can I have? All items of telephone equipment have a Ringer Equivalence
Number (REN), which is used to calculate the number of items which may be connected to any
one telephone line. Your C1LB+ has a REN of 1. A total REN of 4 is allowed. If the total REN of 4 is
exceeded, the telephones may not ring. With dierent telephone types, there is no guarantee of
ringing, even when the REN is less than 4.
Any additional handsets and chargers that you register have a REN of 0.
Connecting to a switchboard
This product is intended for use within Singapore for connection to the public telephone network.
Recall
You may need to use the recall function if you are connected to a switch. Contact your PABX
supplier for further information.
Some jurisdictions do not allow the limitation or exclusion of incidental or consequential
damages, or limitation on the length of an implied warranty, so the above limitations or exclusions
may not apply to you. This warranty gives you specic legal rights, and you may also have other
rights that vary from one jurisdiction to another.
Products Covered Length of Coverage
Consumer Products One (1) year from the date of the products
original purchase by the rst consumer
purchaser of the product.
Consumer Accessories (battery, power
supply(s) and line cords)
Ninety (90) days from the date of the
accessories original purchase by the rst
consumer purchaser of the product.
Consumer Products and Accessories that
are Repaired or Replaced
The balance of the original warranty or for
ninety (90) days from the date returned to the
consumer, whichever is longer.
Exclusions
Normal Wear and Tear. Periodic maintenance, repair and replacement of parts due to normal
wear and tear are excluded from coverage.
Batteries. Only batteries whose fully charged capacity falls below 80% of their rated capacity and
batteries that leak are covered by this limited warranty.
Abuse & Misuse. Defects or damage that result from: (a) improper operation, storage, misuse or
abuse, accident or neglect, such as physical damage (cracks, scratches, etc.) to the surface of
the product resulting from misuse; (b) contact with liquid, water, rain, extreme humidity or heavy
perspiration, sand, dirt or the like, extreme heat, or food; (c) use of the Products or Accessories for
commercial purposes or subjecting the Product or Accessory to abnormal usage or conditions; or
(d) other acts which are not the fault of Motorola or SUNCORP are excluded from coverage.
Use of Non-Motorola branded Products and Accessories. Defects or damage that result from
the use of Non-Motorola branded or certied Products or Accessories or other peripheral
equipment are excluded from coverage.
Unauthorized Service or Modication. Defects or damages resulting from service, testing,
adjustment, installation, maintenance, alteration, or modication in any way by someone other
than Motorola, SUNCORP or its authorized service centers, are excluded from coverage.
Altered Products. Products or Accessories with (a) serial numbers or date tags that have been
removed, altered or obliterated; (b) broken seals or that show evidence of tampering; (c)
mismatched board serial numbers; or (d) nonconforming or non-Motorola branded housings, or
parts, are excluded from coverage.
Communication Services. Defects, damages, or the failure of Products or Accessories due to any
communication service or signal you may subscribe to or use with the Products or Accessories is
excluded from coverage.
Product disposal instructions
Product disposal instructions for residential users
When you have no further use for it, please remove any batteries and dispose of them and the
product according to your local authority’s recycling processes. For more information, please
contact your local authority or the retailer where the product was purchased.
Product disposal instructions for business users
Business users should contact their suppliers and check the terms and conditions of the purchase
contract and ensure that this product is not mixed with other commercial waste for disposal.
Consumer Products and Accessories Warranty
Thank you for purchasing this Motorola branded product manufactured under license by Suncorp
Technologies Limited, 2/F, Shui On Centre, 6-8 Harbour Road, Hong Kong. (“SUNCORP”)
What Does this Warranty Cover?
Subject to the exclusions contained below, SUNCORP warrants that this Motorola branded
product (“Product”) or certied accessory (“Accessory”) sold for use with this product that it
manufactured to be free from defects in materials and workmanship under normal consumer
usage for the period outlined below. This Limited Warranty is your exclusive warranty and is not
transferable.
Who is covered?
This warranty extends only to the rst consumer purchaser, and is not transferable.
What will SUNCORP do?
SUNCORP or its authorized distributor at its option and within a commercially reasonable time,
will at no charge repair or replace any Products or Accessories that do not conform to this limited
warranty. We may use functionally equivalent reconditioned / refurbished / pre-owned or new
Products, Accessories or parts.
What Other Limitations Are There?
ANY IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL BE LIMITED TO
THE DURATION OF THIS LIMITED WARRANTY, OTHERWISE THE REPAIR OR REPLACEMENT
PROVIDED UNDER THIS EXPRESS LIMITED WARRANTY IS THE EXCLUSIVE REMEDY OF THE
CONSUMER, AND IS PROVIDED IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OF IMPLIED.
IN NO EVENT SHALL MOTOROLA OR SUNCORP BE LIABLE, WHETHER IN CONTRACT OR
TORT (INCLUDING NEGLIGENCE) FOR DAMAGES IN EXCESS OF THE PURCHASE PRICE
OF THE PRODUCT OR ACCESSORY, OR FOR ANY INDIRECT, INCIDENTAL, SPECIAL OR
CONSEQUENTIAL DAMAGES OF ANY KIND, OR LOSS OF REVENUE OR PROFITS, LOSS OF
BUSINESS, LOSS OF INFORMATION OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN
CONNECTION WITH THE ABILITY OR INABILITY TO USE THE PRODUCTS OR ACCESSORIES
TO THE FULL EXTENT THESE DAMAGES MAY BE DISCLAIMED BY LAW.
• To avoid interference to nearby appliances, do not place the base of the phone on or near
a TV, microwave oven, or VCR.
Battery Safety Instructions
• Do not burn, disassemble, mutilate, or puncture the battery. The battery contains toxic
materials that could be released, resulting in injury.
IMPORTANT
There is a risk of explosion if you replace the battery with an incorrect battery type. Use only
the batteries that came with your phone or an authorized replacement recommended by the
manufacturer.
• Keep batteries out of the reach of children.
• Remove batteries if storing over 30 days.
• Do not dispose of batteries in re, which could result in explosion.
• The rechargeable batteries that power this product must be disposed of properly and
may need to be recycled. Refer to your battery’s label for battery type. Contact your local
recycling center for proper disposal methods.
SAVE THESE INSTRUCTIONS
Cleaning
• Clean the handset and base (or charger) with a damp (not wet) cloth, or an anti-static
wipe.
• Never use household polish as this will damage the product. Never use a dry cloth as this
may cause static shock.
Environmental
• Do not expose to direct sunlight.
• The handset may become warm when the batteries are being charged or during
prolonged periods of use. This is normal. However, we recommend that to avoid damage,
do not place the product on antique / veneered wood.
• Do not place your product on carpets or other surfaces which generate bres, or place it
in locations preventing the free flow of air over its surfaces.
• Do not submerge any part of your product in water and do not use it in damp or humid
conditions, such as bathrooms.
• Do not expose your product to re, explosives or other hazardous conditions.
• There is a slight chance that your phone could be damaged by an electrical storm. We
recommend that you unplug the power and telephone line cord during an electrical
storm.
aerosol cleaners. Use a damp cloth for cleaning.
• Do not disassemble this product. If service or repair work is required, contact the
customer service helpline found in this user’s Guide.
• Do not overload wall outlets and extension cords.
• Avoid using during an electrical storm. Use a surge protector to protect the equipment.
• Do not use this phone to report a gas leak, especially if you are in the vicinity of the gas
line.
IMPORTANT
To reduce the risk of re, use only the supplied power adaptor.
Unplug this cordless phone immediately from an outlet if:
• The power cord or plug is damaged or frayed.
• Liquid has been spilled on the product.
• The product has been exposed to rain or water. Do not retrieve the handset or base until
after you have unplugged the power and phone from the wall. Then retrieve the unit by
the unplugged cords.
• The product has been dropped or the cabinet has been damaged.
• The product exhibits a distinct change in performance.
Installation Guidelines
• Read and understand all instructions and save them for future reference.
• Follow all warnings and instructions marked on the product.
• Do not install this product near a bath tub, sink, or shower.
• Operate this phone using only the power source that is indicated on the marking label. If
you are unsure of the power supply to your home, consult with your dealer or local power
company.
• Do not place this product on an unstable cart, stand, or table. This product may fall,
causing serious damage to the product.
• Adjust only those controls that are covered by the operating instructions. Improper
adjustment of other controls may result in damage and will often require extensive work to
restore the product to normal operation.
• Clean this product with a soft, damp cloth. Do not use chemicals or cleaning agents to
clean this phone.
• Use only the power supply that came with this unit. Using other power supplies may
damage the unit.
• Because this phone operates on electricity, you should have at least one phone in your
home that could operate without electricity in the case the power in your home goes out.
No Caller ID
• Check your subscription with your network operator.
• The caller may have withheld their number.
• The record cannot be found in your phonebook. Check that you have the correct name /
number stored in your phonebook, with the full area code.
I have forgotten my PIN!
• Restore your C1LB+ to its default settings, see “6.7 Emergency default”,.
Cannot register a handset to the base
• You can register up to a maximum of 5 handsets to a C1LB+ base. You must de-register a
handset in order to register a new one.
• Check that you have entered the correct PIN code (default = 0000).
• Check that you are at least one metre away from other electrical equipment to avoid
interference when registering.
Handset does not ring
• The handset ringer volume may be set to O.
Noise interference on my phone or on other electrical equipment nearby
• Place your C1LB+ at least one metre away from electrical appliances or any metal
obstructions to avoid any risk of interference.
11. General information
IMPORTANT
This equipment is not designed to make emergency telephone calls when the power fails.
Alternative arrangements should be made for access to emergency services.
This product is intended for connection to analogue public switched telephone networks and
private switchboards in Singapore.
Important safety instructions
Follow these safety precautions when using your phone to reduce the risk of re, electric shock,
and injury to persons or property:
• Keep all slits and openings of the phone unblocked. Do not set the phone on a heating
register or over a radiator. Ensure that proper ventilation is provided at the installation site.
• Do not use while wet or while standing in water.
• Do not use this product near water (for example, near a bath tub, kitchen sink, or
swimming pool).
• Do not allow anything to rest on the power cord. Place the power cord so that it will not be
walked on.
• Never insert objects of any kind into the product vents as that may result in re or electric
shock.
• Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or
4. Press m to conrm. You will hear a conrmation beep and the display will return to
standby.
NOTE
If you select
AUTO
, your handset will automatically search for and connect to the base with the
strongest signal.
9.4 De-register a handset
Use one handset to de-register another. You cannot de-register the handset that you are using.
1. Press m, scroll d to
SETUP
and press m.
2. The display sows
DEL HANDSET
, press m.
3. Enter the 4 digit PIN code (default = 0000) and press m.
4. Enter the handset number that you want to de-register. You will hear a conrmation beep and
the display will return to the previous menu.
10. Help
No dial tone
• Use only the telephone line cord supplied.
• Check that the telephone line cord is connected properly.
• Check that the mains power is connected properly and switched on.
No display
• Check that the batteries are inserted correctly and fully charged. Use only approved
rechargeable batteries supplied.
• Check that the handset is switched on. Press and hold n.
• Reset the base by removing the batteries and disconnecting the mains power. Wait for
around 15 seconds before connecting it again. Allow up to one minute for the handset and
base to synchronize.
icon flashes
• Handset is out of range. Move closer to the base.
• Make sure that the handset is registered to the base.
• Check that the mains power is connected properly and switched on.
Keypad does not seem to work
• Check that the keypad lock is not on.
icon is not scrolling during charge
• Adjust the handset slightly on the base.
• Clean the charging contacts with a cloth moistened with alcohol.
• Check that the mains power is connected properly and switched on.
• The battery is full. When the handset is fully charged, icon will appear steady on the
display.
On the handset:
1. Press m, scroll d to
REGISTER
and press m.
2. Scroll d to
REG BASE
and press m.
3. Enter the base number (1 - 4).
The base numbers that are already in use flash.
4. The display shows
SEARCHING...X
, where
X
indicates the base identication number.
5. The display will ask for the PIN to be entered. Enter the 4 digit PIN code (default = 0000) and
press m. You will hear a beep if the registration is successful. The handset is automatically
assigned an available handset number. Use this number when making internal calls.
NOTE
If registration is not successful the rst time, please repeat the process again in case the base
registration period ran out of time. If the base is not found after a few seconds, the handset
returns to standby. Try registering again.
If there are already 5 handsets registered to the base, the registration will fail. You must de-
register another handset before you can register a new one.
9.2 Register a dierent make of handset to your C1LB+ base
IMPORTANT
DECT GAP Prole only guarantees that basic calling functions will work correctly between
dierent makes / types of handset and base. There is a possibility that certain features such as
Caller ID will not work correctly.
On the base:
1. Press and hold for 3 seconds until you hear two beeps. The base will remain in registration
mode for 90 seconds.
On the handset:
Follow the registration instructions given in your handset’s user guide.
9.3 Select a base
If your C1LB+ handset is registered to more than one base (e.g. one at work and one at home),
you can select which base to use.
Each handset can be registered with up to four bases.
1. Press m, scroll d to
REGISTER
and press m. The display shows
SELECT BASE
.
2. Press m. All the bases that your handset has been registered to will be displayed, e.g.
BASE
1 2 3 4
. The currently selected base number flashes.
3. Enter the base number that you want to use. Alternatively, press u or d to scroll to
AUTO
.
8.2.3 Copy a Calls list number to the phonebook
1. Press d to open the Calls list.
2. Scroll u or d to the entry you want.
3. Press m repeatedly until the display shows
ADD ?
.
4. Press m again. The display shows
NAME ?
.
5. Enter the name and press m. The number is displayed.
6. Edit the number if necessary, then press m.
7. Press u or d to select the ringer melody you want and press m.
The number is stored.
8.2.4 Delete an entry
1. Press d to open the Calls list.
2. Scroll u or d to the entry you want and press p. The display shows
DELETE ?
.
3. Press m to conrm or p to cancel.
8.2.5 Delete the entire Calls list
1. Press d to open the Calls list.
2. Press and hold p. The display shows
DELETE ALL ?
.
3. Press m to conrm or p to cancel.
9. Using additional handsets
You can register up to ve handsets to your C1LB+ base to extend your phone system without
having to install extension sockets for each new phone.
Each C1LB+ handset can be registered with up to four bases. You can then select the base you
prefer to use. If you have purchased a C1LB+ multiple pack, all additional handsets come pre-
registered to the base.
If you have purchased an additional handset separately, you must register it to your C1LB+ base
before it can be used.
9.1 Registering an additional handset
NOTE
Handset batteries must be fully charged before you start to register. Hold your handset close to
the base during the registration process. Handsets that were supplied with your C1LB+ base are
already pre-registered.
On the base:
1. Press and hold for 3 seconds until you hear two beeps. The base will remain in registration
mode for 90 seconds.
If the call is from an international number,
INT’L
will be displayed.
If the call is from the operator,
OPERATOR
will be displayed.
If the call is from a payphone,
PAYPHONE
will be displayed.
If the call is from a ringback request,
RINGBACK
will be displayed.
8.1 Caller ID
If you have subscribed to a Caller ID Service, you will be able to see your caller’s number on your
handset (provided it is not withheld) prior to answering the call. The display can show the rst 12
digits or characters of the phone numbers and names.
If your caller’s name and number are stored in the phonebook and a number match is found, you
will see the caller’s name on the display instead.
8.2 Calls list
The Calls list stores details of your last 40 received calls, including the phone number and date
and time of the call.
The Calls list also alerts you when you have unanswered calls.
The caller’s details are stored in the Calls list whether or not you have answered the call. The list is
shared by all handsets registered to the base. When the list is full, and a new call is received, the
oldest entry will be deleted automatically.
When a new call is received in the Calls list, icon will flash on the display in standby mode to
alert you. When you have viewed the new call, icon disappears but icon will remain.
8.2.1 View the Calls list
1. Press d to open the Calls list. If there are no calls in the list, the display shows
EMPTY
.
2. Press u or d to scroll through the list.
• If the call was answered, icon is displayed as you scroll to the entry. If the call was
unanswered, icon is displayed as you scroll to the entry. When you reach the end of the
list, the handset will beep.
• If the caller’s number exactly matches an entry stored in the phonebook, the display will
alternate between the name and the number. Press m to see the caller’s number.
• If the telephone number is longer than 12 digits, icon is displayed. Press m to see
the remaining digits.
• Press m again to see the time and date of the call.
• Press m again to access the option to store the entry in your phonebook.
8.2.2 Dial a number in the Calls list
1. Press d to open the Calls list.
2. Scroll u or d to the entry you want.
3. Press t to dial the displayed entry.
7. Clock & alarm
If you have subscribed to Caller ID Service, the date and time will be set on all your handsets
whenever a call is received. You can also manually set the date and time on the individual
handsets.
7.1 Set the date
1. Press m, scroll d to
DATE -- TIME
and press m. The display shows
DATE SET
.
2. Press m to select.
3. Enter the date (e.g. 12--08 for 12th of August) and press m to conrm.
7.2 Set the time
1. Press m, scroll d to
DATE -- TIME
and press m.
2. Scroll d to
CLOCK SET
and press m.
3. Enter the time in 24 hour format (e.g. 18--30 for 6:30pm) and press m to conrm.
7.3 Set alarm
Each handset can have a dierent alarm setting.
1. Press m, scroll d to
DATE -- TIME
and press m.
2. Scroll d to
ALARM SET
and press m.
3. Press u or d to select
ON
or
OFF
and press m to conrm.
4. If you select
ON
, enter the time in 24 hour format (e.g. 07--30 for 7:30am) and press m to
conrm.
7.4 Switch o alarm ring
When the alarm sounds, press any button to switch it o.
NOTE
If you are using the handset to make a call when the alarm ring is due, you will hear a beep in the
earpiece.
8. Caller ID and the Calls list
IMPORTANT
To use Caller ID, you must rst subscribe to the service from your network provider. A subscription
fee may be payable.
To ensure that the caller’s name is displayed, make sure you have stored the full telephone
number, including the area code in the phonebook.
If the call is a withheld call,
WITHHELD
will be displayed.
If the number is unavailable,
UNAVAILABLE
will be displayed.
2. Scroll d to
DEFAULT
and press m.
3. Enter the 4 digit PIN code (default = 0000) and press m. The display shows
CONFIRM ?
.
4. Press m to conrm or p to return to the previous menu. Your C1LB+ will restart
automatically.
6.5 Emergency default
If you have lost your PIN code, you can still restore your C1LB+ to its default settings.
1. Remove the batteries from the handset.
2. Press and hold * while replacing the batteries. The display
shows
DEFAULT.
3. Press m to conrm. Your C1LB+ will restart automatically.
6.6 Eco mode
Your C1LB+ oers ECO mode function which reduces the transmitted power and energy
consumption when switched on.
To switch Eco mode on:
1. Press m, scroll d to
SETUP
and press m.
2. Scroll d to
ECO MODE
and press m.
3. Press u or d to select
ON
or
OFF
and press m to conrm.
NOTE
When ECO mode is set to ON, the handset range will be reduced.
On the handset display when ECO mode is switch o the circle around the disappears.
6.7 Default settings
Low battery beeps ON Phonebook Empty
Out of range warning beeps ON Calls list Empty
Key beep ON Redial list Empty
Auto answer ON PIN code 0000
Internal melody 1 Dial mode Tone
Internal volume 3 Recall mode TIMED BR, 2
(600 ms)
External melody 3 Eco mode OFF
External volume 3 Keypad lock OFF
Ear volume 2
6. Base settings
6.1 Change base PIN code
Some functions are protected by a 4 digit PIN code which must be entered if you want to change
the settings. The default PIN is 0000. You can change this to your own preferred number.
When you enter a PIN, the digits are shown as ****.
1. Press m, scroll d to
SETUP
and press m.
2. Scroll d to
PIN CODE
and press m.
3. Enter the 4 digit PIN code (default = 0000) and press m.
4. Enter the new PIN and press m to conrm.
5. The display shows
RETYPE
. Re-enter the new PIN and press m to conrm.
IMPORTANT
If you change the PIN code, please keep a record of the new number.
6.2 Dial mode
Your C1LB+ is set to tone dialling. You should only need to change this if connected to an older
type of switchboard / PBX which requires pulse dialling.
1. Press m, scroll d to
SETUP
and press m.
2. Scroll d to
DIAL MODE
and press m.
3. Press u or d to select
TONE DIAL
or
PULSE DIAL
and press m to conrm.
6.3 Recall mode
Depending on your country and network operator, your C1LB+ has the recall time set as TIMED
BR, 2 (600 ms). It is unlikely that you need to change this setting unless advised to do so.
1. Press m, scroll d to
SETUP
and press m.
2. Scroll to
RECALL
and press m.
3. Press u or d to select
TIMED BR,1
(short flash time) or
TIMED BR,2
(long flash time) and
press m to conrm.
6.4 Restore default settings
You can restore your C1LB+ to its default (original) settings.
All the handsets that are registered to the base will be retained.
IMPORTANT
Resetting your phone to its default settings will delete all entries in the Phonebook and Calls list.
All handset and base settings will also be reset.
1. Press m, scroll d to
SETUP
and press m.
5.5 Language
1. Press m, scroll d to
HANDSET
and press m.
2. Scroll d to
LANGUAGE
and press m.
3. Press u or d to select your preferred language and press m to conrm.
5.6 Key beep
When you press a button on the handset keypad, you will hear a beep. You can switch these
beeps on or o.
1. Press m, scroll d to
HANDSET
and press m. The display shows
BEEP
.
2. Press m to select. The display shows
KEYTONE
.
3. Press m to select.
4. Press u or d to select
ON
or
OFF
and press m to conrm.
5.7 Battery low warning beep
When the battery is almost fully discharged, you will hear a warning beep every minute during a
call. You can switch these beeps on or o.
1. Press m, scroll d to
HANDSET
and press m. The display shows
BEEP
.
2. Press m to select.
3. Scroll d to
LOW BATTERY
and press m.
4. Press u or d to select
ON
or
OFF
and press m to conrm.
5.8 Out of range warning beep
If the handset goes out of range, you will hear warning beeps during a call. You can switch these
beeps on or o.
1. Press m, scroll d to
HANDSET
and press m. The display shows
BEEP
.
2. Press m to select.
3. Scroll d to
OUT RANGE
and press m.
4. Press u or d to select
ON
or
OFF
and press m to conrm.
5.9 Keypad lock using the menu
You can use the menu to lock the keypad.
1. Press m, scroll d to
HANDSET
and press m.
2. Scroll d to
KEYLOCK ?
and press m to conrm.
icon is displayed.
NOTE
To unlock the keypad, press any button on the keypad, then press * within 5 seconds.
4. Press m to conrm or p to return to the previous menu.
NOTE
When the phone is ringing, you can adjust the ringer volume by pressing u or d.
5.2 Handset ringer melody
You can set dierent ringer melodies for your internal and external calls. Choose from 10 dierent
ringer melodies.
You will hear a sample ring as you scroll to each ring melody.
1. Press m, scroll d to
HANDSET
and press m.
2. Press u or d to select
INT MELODY
or
EXT MELODY
and press m.
3. Press u or d to select the ringer melody (1 - 10).
4. Press m to conrm or p to return to the previous menu.
NOTE
If you subscribe to your network providers caller ID service, calls from the numbers that you have
stored in the phonebook will ring using the ringer melody you have set when you store the entry.
5.3 Auto answer
Your phone is set to answer calls by lifting the handset o the base or charger. You can switch this
feature o so that calls can only be answered by pressing t.
1. Press m, scroll d to
HANDSET
and press m.
2. Scroll d to
AUTO ANSWER
and press m.
3. Press u or d to select
ON
or
OFF
and press m to conrm.
5.4 Handset name
If you are using more than one handset with your C1LB+ base, you can set a personalized name
for each handset to easily distinguish between them.
A name can be up to 10 characters long.
1. Press m, scroll d to
HANDSET
and press m.
2. Scroll d to
NAME
and press m.
3. Enter the new handset name and press m to conrm.
Delete the current name by pressing p.
NOTE
The handset name will only be displayed for approximately 20 seconds when no button is
pressed. If you make a mistake, press p to delete the last character or digit.
Declaration of Conformity (DoC)
Suncorp declares that the following products:
Brandname: Motorola
Type: C1001LB+, C1002LB+, C1003LB+ and C1004LB+
Descriptions: DECT phone without telephone answering machine (C100xLB+) and
their multi-handset versions.
to which this declaration related is in conformity with the essential requirements of the following
directives of the Council of the European Communities:
- R&TTE Directive (1999/5/EC)
- Ecodesign Directive (2009/125/EC)
The products are compliant with the following standards:
Safety: EN60950-1:2006+A11:2009+A1:2010+A12:2011
EMC: EN301489-1 v1.9.2 and EN301489-6 v1.3.1
RF Spectrum : EN301406 v2.1.1
Ecodesign : EC No 278/2009, 6 April 2009
For and on behalf of Suncorp Technologies Limited,
Signature: ______________________
Printed name & Position: CW Cheung – Chief Technical Officer
Date: July 23, 2013
Place: 2/F, Shui On Centre, 6-8 Harbour Road, Hong Kong
CW Cheung
2013.07.23
14:19:25 +08'00'