Philips 221T1SB/05 User Manual
Displayed below is the user manual for 221T1SB/05 by Philips which is a product in the Computer Monitors category. This manual has pages.
Related Manuals
Register your product and get support at
www.philips.com/welcome
201T1
221T1
231T1
EN User Manual
www.philips.com/support
Model
Serial
This information is correct at the time of press. For updated information, see www.philips.com/support.
Country Code Telephone number Tariff
Austria +43 0810 000206 0.07
Belgium +32 078 250851 0.06
Denmark +45 3525 8761 Local call tariff
Finland +358 09 2290 1908 Local call tariff
France +33 082161 1658 0.09
Germany +49 01803 386 853 0.09
Greece +30 00800 3122 1223 Free of charge
Ireland +353 01 601 1161 Local call tariff
Italy +39 840 320 041 0.08
Luxembourg +352 26 84 30 00 Local call tariff
The Netherlands +31 0900 0400 063 0.10
Norway +47 2270 8250 Local call tariff
Poland +48 0223491505 Local call tariff
Portugal +351 2 1359 1440 Local call tariff
Spain +34 902 888 785 0.10
Sweden +46 08 632 0016 Local call tariff
Switzerland +41 02 2310 2116 Local call tariff
United Kingdom +44 0207 949 0069 Local call tariff
1
English
EN
Contents
1 Notice 2
2 Important 4
The most updated user manual on line 5
3 Get started and connect your devices 6
Back connector 6
Side connector 8
4 Controls 9
Front and side controls 9
Remote control 9
5 Start to use 12
Switch your TV on/off or to standby 12
Switch channels 12
Watch connected devices 13
Adjust TV volume 13
6 Product information 14
Supported display resolutions 14
Tuner/Reception/Transmission 14
Remote control 14
Power 14
Supported TV mounts 14
7. TV/Channel settings 15
Using TV signal as the input source. 15
To adjust the country for auto tuning 15
Audio Carrier(Analog TV only) 15
1st Audio and 2nd Audio (Digital TV only) 16
Channel Scan 16
Update Scan 17
Single RF Scan (Digital TV only) 17
Analog Manual Scan (Analog TV only) 18
Channel Skip 18
Channel Sort (Swap) 19
Channel Edit 19
Decoder (Analog TV only) 20
Analog Ch Fine Tune (Analog TV only) 20
Appendix 20
8. Feature setting highlights: 21
Using the Teletext 21
Using the EPG 22
Parental Menu setting: 22
Channel Block 22
Parental Guidance 23
Input Block 23
Set Password 24
Clean All 24
OAD update: 24
9. Pixel policy 24
10. Troubleshooting 27
General TV issues 27
TV channel issues 27
Picture issues 27
Sound issues 28
HDMI connection issues 28
Computer connection issues 28
Others 28
Contact us 29
2
Pixel characteristics
This LCD product has a high number of
colour pixels. Although it has effective
pixels of 99.999% or more, black dots or
bright points of light (red, green or blue)
may appear constantly on the screen.
This is a structural property of the display
(within common industry standards) and
is not a malfunction.
Mains fuse (UK only)
This TV is tted with an approved
moulded plug. Should it become
necessary to replace the mains fuse, this
must be replaced with a fuse of the same
value as indicated on the plug (example
10A).
1 Remove fuse cover and fuse.
2 The replacement fuse must comply with
BS 1362 and have the ASTA approval
mark. If the fuse is lost, contact your
dealer in order to verify the correct type.
3 Ret the fuse cover.
In order to maintain conformity to the
EMC directive, the mains plug on this
product must not be detached from the
mains cord cable.
1 Notice
2009 © Koninklijke Philips Electronics N.V. All
rights reserved.
Specications are subject to change without
notice. Trademarks are the property of
Koninklijke Philips Electronics N.V or their
respective owners. Philips reserves the right
to change products at any time without being
obliged to adjust earlier supplies accordingly.
The material in this manual is believed
adequate for the intended use of the system.
If the product, or its individual modules or
procedures, are used for purposes other than
those specied herein, conrmation of their
validity and suitability must be obtained. Philips
warrants that the material itself does not
infringe any United States patents. No further
warranty is expressed or implied.
Warranty
Risk of injury, damage to TV or void of •
warranty! Never attempt to repair the
TV yourself.
Use the TV and accessories only as •
intended by the manufacturer.
The caution sign printed on the back of •
the TV indicates risk of electric shock.
Never remove the TV cover. Always
contact Philips Customer Support for
service or repairs.
Any operation expressly prohibited in •
this manual, or any adjustments and
assembly procedures not recommended
or authorised in this manual shall void the
warranty.
EN
3
Copyright
VESA, FDMI and the VESA Mounting Compliant
logo are trademarks of the Video Electronics
Standards Association.
® Kensington and Micro Saver are registered
US trademarks of ACCO World Corporation
with issued registrations and pending
applications in other countries throughout the
world.
Manufactured under licence from Dolby
Laboratories. ‘Dolby’ and the double D symbol
are trademarks of Dolby Laboratories. (Only
applicable to TVs supporting MPEG4-HD
standard).
All other registered and unregistered
trademarks are the property of their respective
owners.
English
EN
4
When stand mounting the TV, use •
only the supplied stand. Secure the
stand to the TV tightly. Place the
TV on a at, level surface that can
support the combined weight of the
TV and the stand.
When wall mounting the TV, use •
only a wall mount that can support
the weight of the TV. Secure the wall
mount to a wall that can support the
combined weight of the TV and wall
mount. Koninklijke Philips Electronics
N.V. bears no responsibility for
improper wall mounting that result in
accident, injury or damage.
Risk of injury to children! Follow these •
precautions to prevent the TV from
toppling over and causing injury to
children:
Never place the TV on a surface •
covered by a cloth or other material
that can be pulled away.
Ensure that no part of the TV hangs •
over the edge of the surface.
Never place the TV on tall furniture •
(such as a bookcase) without
anchoring both the furniture and TV
to the wall or a suitable support.
Educate children about the dangers •
of climbing on furniture to reach the
TV.
Risk of overheating! Never install the •
TV in a conned space. Always leave a
space of at least 4 inches around the TV
for ventilation. Ensure curtains or other
objects never cover the ventilation slots
on the TV.
Risk of damage to the TV! Before you •
connect the TV to the power outlet,
ensure that the power voltage matches
the value printed on the back of the TV.
Never connect the TV to the power
outlet if the voltage is different.
• Risk of injury, re or power cord damage!
Never place the TV or any objects on the
power cord.
To easily disconnect the TV power cord •
from the power outlet, ensure that you
have full access to the power cord at all
times.
When you disconnect the power cord, •
always pull the plug, never the cable.
2 Important
Read and understand all instructions before you
use your TV. If damage is caused by failure to
follow instructions, the warranty does not apply.
Safety
• Risk of electric shock or re!
Never expose the TV to rain or •
water. Never place liquid containers,
such as vases, near the TV. If
liquids are spilt on or into the TV,
disconnect the TV from the power
outlet immediately. Contact Philips
Consumer Care to have the TV
checked before use.
Never place the TV, remote control •
or batteries near naked ames or
other heat sources, including direct
sunlight.
To prevent the spread of re, keep
candles or other ames away from
the TV, remote control and batteries
at all times.
• Never insert objects into the
ventilation slots or other openings on
the TV.
When the TV is swivelled ensure •
that no strain is exerted on the
power cord. Strain on the power
cord can loosen connections and
cause arcing.
Risk of short circuit or re!•
Never expose the remote control or •
batteries to rain, water or excessive
heat.
Avoid force coming onto power •
plugs. Loose power plugs can cause
arcing or re.
Risk of injury or damage to the TV!•
Two people are required to lift and •
carry a TV that weights more than
25 kg.
EN
5
Recycling
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
When you see the crossed-out wheeled bin
symbol attached to a product, it means the
product is covered by the European Directive
2002/96/EC:
Never dispose of your product with other
household waste. Please inform yourself about
the local rules on the separate collection of
electrical and electronic products. The correct
disposal of your old product helps prevent
potentially negative consequences for the
environment and human health.
Your product contains batteries covered by
the European Directive 2006/66/EC, which
cannot be disposed of with normal household
waste.
Please inform yourself about the local rules
on the separate collection of batteries. The
correct disposal of batteries helps prevent
potentially negative consequences for the
environment and human health.
The most updated user
manual on line
The contents of the user manual are subject
to change. Please refer to www.philips.com/
support for the most updated user manual info
reference.
• Disconnect the TV from the power outlet
and aerial before lightning storms. During
lightning storms, never touch any part of
the TV, power cord or aerial cable.
Risk of hearing damage! Avoid using •
earphones or headphones at high
volumes or for prolonged periods of time.
If the TV is transported in temperatures •
below 5°C, unpack the TV and wait
until the TV temperature matches room
temperature before connecting the TV to
the power outlet.
Screen care
• Avoid stationary images as much as
possible. Stationary images are images
that remain on-screen for extended
periods of time. Examples include:
on-screen menus, black bars and time
displays. If you must use stationary
images, reduce screen contrast and
brightness to avoid screen damage.
Unplug the TV before cleaning.•
Clean the TV and frame with a soft, •
damp cloth. Never use substances such as
alcohol, chemicals or household cleaners
on the TV.
Risk of damage to the TV screen! Never •
touch, push, rub or strike the screen with
any object.
To avoid deformations and colour fading, •
wipe off water drops as soon as possible.
English
EN
6
a PC IN (VGA and AUDIO IN)
Audio and video input from a computer.
b EXT 2 (Y Pb Pr and AUDIO L/R)
Analogue audio and video input from
analogue or digital devices such as DVD
players or game consoles.
AUDIO
VGA
VGA
3 Get started and
connect your
devices
Congratulations on your purchase, and
welcome to Philips! To fully benet from the
support that Philips offers, register your product
at www.philips.com/welcome.
This section describes how to connect
various devices with different connectors and
supplements examples provided in the Quick
Start.
Note
Different types of connectors may be used to •
connect a device to your TV, depending on
availability and your needs.
Back connector
7
7
e AV OUT (VIDEO OUT and AUDIO
OUT L/R)
Audio and video output to analogue
devices such as another TV or a recording
device.
f SPDIF OUT
Digital audio output to home theatres
and other digital audio systems.
g HDMI
Digital audio and video input from high-
denition digital devices such as Blu-ray
players.
Connections via DVI or VGA require an
additional audio cable.
AUDIO
IN
c EXT 1 (SCART)
Analogue audio and video input from
analogue or digital devices such as DVD
players or game consoles.
d TV ANTENNA
Signal input from an antenna, cable or
satellite.
English
8
b AUDIO L/R
Audio input from analogue devices
connected to VIDEO.
c VIDEO
Composite video input from analogue
devices such as VCRs.
d SERVICE
USB port, for upgrade rmware purpose
only.
Side connector
a COMMON INTERFACE
Slot for a Conditional Access Module
(CAM).
1
2
3
4
9
Remote control
1
26
23
16
14
13
12
11
10
17
15
18
19
20
8
7
6
4
2
9
5
3
28
27
25
24
22
21
31
32
33
34
29
30
4 Controls
Front and side controls
a POWER: Switches the TV on or off.
The TV is not powered off completely
unless it is physically unplugged.
b SOURCE: Selects connected devices.
c MENU/OK : Displays the on-screen
menu and conrms a selection in menus.
d CH +/-: Switches to the next or previous
channel.
e VOL+/-: Increases or decreases volume.
f Power indicator :
Red LED: In standby mode or off.
Green LED: Power on.
6
4
5
2
3
1
EN
English
10
a (Standby-On)
Switch the TV to standby if the TV •
is on.
Switch the TV on if the TV is in •
standby.
b 0-9 ( Numeric buttons )
Select a channel or setting.
c PRE CH
Return to the previously viewed channel.
d TV
Press to choose TV mode.
e PC
Press to choose PC mode.
f (Mute)
Switch the sound On or Off.
g CH Λ / V (Channel Λ / V )
Switch to the next or previous channel.
h ZOOM
Toggle among screen formats.
i SLEEP
Toggle to select the preset time to switch
the TV to standby mode automatically.
j PICTURE
Toggle to select the Smart Picture setting.
k OK
Conrm an entry or selection and display
the channel grid, when watching TV.
l ▲▼◄►(Navigationbuttons)
Navigate through the menus.
m INFO
Display or hide the information screen
about the selected channel.
n Colour buttons
Select tasks or options.
o SIZE
Toggle to change the font size in Teletext
mode. (Full screen / Top half / Bottom
half)
p SUBPAGE
Display the sub page when the Teletext
information has more than one page.
q REVEAL
Reveal hidden information of Teletext.
r HOLD
Toggle to stop the scrolling of pages to
stop the text decoder receiving data.
s FREEZE
Press to freeze the TV picture.
t AD (Audio Description) (For RF Digital
TV only)
UK only: Enables audio commentary for
the visually handicapped.
u SOURCE
Select connected devices.
v EPG
Switch the Electronic Programme Guide
On or Off.
w VIDEO
Press to switch to VIDEO YPbPr /
Composite /SCART mode.
x HDMI
Press to switch to HDMI mode.
y VOL +/-
Increase or decrease the volume.
z DUAL I-II
Toggle to select mono / stereo / dual I/
dual II from TV RF input.
{ SOUND
Toggle to select the Smartsound Mode.
| MENU/EXIT
Press to open or close the on-screen
menu.
} MIX
Press to overlay the Teletext page on the
TV picture.
~ TELETEXT
Press to open or close the Teletext.
INDEX
11
English
EN
Press to display the index page of
Teletex t .
€ SUBTITLE
In TV mode: Press to turn the •
subtitle on or off.
In Text mode: Press to open the •
subtitle page.
FAV
Press to display the Favourite List.
‚ CH-LIST
Press to display the Channel List.
12
Note
If you cannot locate your remote control and •
want to switch on the TV from standby, press
CH +/- at the side of the TV.
Switch channels
Press • CH ^/v on the remote control or
CH +/- on the side of the TV.
Enter a channel number using the •
Numeric buttons.
Use the channel grid.•
Note
When you use a favourite list, you can only •
select those channels in the list.
5 Start to use
This section helps you perform basic TV
operations.
Switch your TV on/off or to
standby
To switch on
If the standby indicator is off, press •
POWER at the side of the TV.
If the standby indicator is red, press •
(Standby-On) on the remote control.
To switch to standby
Press • (Standby-On) on the remote
control.
The standby indicator switches to red. »
To switch off
Press • POWER at the side of the TV.
The standby indicator switches off. »
Tip
Though your TV consumes very little power •
when in standby, energy continues to be
consumed. When not in use for an extended
period of time, disconnect the TV power cable
from the power outlet.
EN
13
Watch connected devices
Note
Switch on the device before selecting it as a •
source on the TV.
Use the source button
1 Press SOURCE.
The source list appears. »
2 Press the SOURCE,▲or▼buttons to
select a device.
3 Press OK to conrm your choice.
The sTV switches to the selected »
device.
The TV switches to the selected »
device.
English
EN
Adjust TV volume
To increase or decrease volume
Press • VOL +/- on the remote control.
Press • VOL +/- on the side of the TV.
To mute or unmute sound
Press • to mute the sound.
Press • again to restore the sound.
14
Remote control
Type: 201T1, 221T1, 231T1 RC•
Batteries: 2 x AAA (LR03 type)•
Power
Mains power: 100-240V, 50Hz•
Off mode power: < 0.5W•
Ambient temperature: 5 to 40 degrees •
Celsius
Supported TV mounts
To mount the TV, purchase a Philips TV mount
or a VESA-compatible TV mount. To prevent
damage to cables and connectors, be sure to
leave a clearance of at least 5.5 cm from the
back of the TV.
Warning
•Follow all instructions provided with the TV
mount. Koninklijke Philips Electronics N.V. bears
no responsibility for improper TV mounting that
results in accident, injury or damage.
TV screen
size (inches)
Required
pitch (mm)
Required
mounting bolts
20 100 x 100 4 x M4
22 100 x 100 4 x M4
23 100 x 100 4 x M4
EN
6 Product
information
Product information is subject to change
without notice. For detailed product
information, go to www.philips.com/support.
Supported display
resolutions
Computer formats
Resolution - refresh rate:•
640 x 480 - 60Hz•
640 x 480 - 75Hz•
800 x 600 - 60Hz•
800 x 600 - 75Hz•
1024 x 768 - 60Hz•
1024 x 768 - 75Hz•
1280 x 1024 - 60Hz•
1440 x 900 - 60Hz•
1600 x 900 - 60Hz (the best for •
201T1)
1680 x 1050 - 60H z•
1920 x 1080 - 60Hz_RB (the best •
for 221T1 and 231T1)
Video formats
Resolution - refresh rate:•
480i - 60Hz•
480p - 60Hz•
576i - 50Hz•
576p - 50Hz•
720p - 50Hz, 60Hz•
1080i - 50Hz, 60Hz•
1080p - 50Hz, 60Hz•
Tuner/Reception/
Transmission
Antenna input: 75ohm coaxial (IEC75)•
DVB: DVB Terrestrial, DVB-T MPEG4 •
TV system: DVB COFDM 2K/8K; PAL I, •
B/G, D/K; SECAM B/G, D/K, L/L’
Video playback: NTSC, SECAM, PAL•
Tuner Bands: Hyperband, S-channel, •
UHF, VHF
15
To adjust the country for
auto tuning
Press MENU + UP / DOWN button to ►
select TV.
Press OK + UP / DOWN button to ►
select Country.
Press LEFT / RIGHT button to select the ►
item.
Audio Carrier(Analog TV
only)
Select Mono / Stereo / Dual l / Dual ll ,for ►
preference
Note
if your preference is not the workable carrier, •
the default priority will be : Dual l > Dual ll
;Stereo > Mono.
Exit Back
A u d i o C a r r i e r S t e r e o
C h a n n e l s
Exit Back
C o u n t r y U K
C h a n n e l s
7. TV/Channel
settings
This chapter provides adjust the program
related settings and the audio language related
settings
Using TV signal as the input
source.
Press MENU button to display the menu. ►
Press UP / DOWN button to select the ►
TV item.
Press OK button enter the TV sub item. ►
Press MENU button to exit the sub item. ►
C o u n t r y U K
A u d i o C a r r i e r S t e r e o
C h a n n e l s
English
EN
16
Channel Scan
Use this function to nd and store all available •
channels automatically in both digital and analog
mode.
Press MENU + UP / DOWN button to ►
select TV.
Press OK + UP / DOWN button to ►
select Channels.
Press OK + UP / DOWN button to ►
select Channel Scan.
Press OK button to execute the Channel ►
Scan.
Channel Scan scan both the digital and »
analog channels, rst scan digital channels
and analog channels last.
Channel Scan will erase all old stored
»
channels scanned by previous execution.
Digital channel number will assign by
»
LCN (Logical Channel Number) if LCN
is exist.
Digital channel which no LCN or LCN
»
con ict will assign from 800 to 899.
Analog channels will assign from 901
»
to 999, if have channel name, will assign
from 901, others will assign by frequency,
2 7 %
Exit Cancel
S t a t u s : S c a n n i n g .
A n a l o g C h a n n e l s : 0
D i g i t a l C h a n n e l s : 0
1st Audio and 2nd Audio
(Digital TV only)
The Audio function allows selection of a •
preferred language.
If audio data in a selected language is not
•
broadcast, the default language audio will be
played.
When the languages you selected as the primary
•
for Audio Language are not supported, you can
select language in secondary category.
Press MENU + UP / DOWN button to ►
select TV.
Press OK + UP / DOWN button to ►
select 1st Audio and 2nd Audio.
Press LEFT / RIGHT button to select the ►
item.
Exit Back
C o u n t r y U K
2 n d A u d i o E n g l i s h
C h a n n e l s
EN
17
Single RF Scan (Digital TV
only)
Single RF Scan lets you manually add a digital •
channel to your channel list.
Press MENU + UP / DOWN button to ►
select TV.
Press OK + UP / DOWN button to ►
select Channels.
Press OK + UP / DOWN button to ►
select Single RF Scan.
Press OK button to display the DTV or ►
TV channel info.
Press LEFT / RIGHT button to change ►
RF Channel.
Press OK button to scan. ►
Exit Back
S c a n s i n g l e R F c h a n n e l . ( D i g i t a l
O n l y )
0 %
S i g n a l S t r e n g t h 0
S i g n a l Q u a l i t y P o o r
OK Enter
If can’t scan any digital channels, only »
analog channels, will assign analog
channel from 1.
Update Scan
To check if any new channel is available. Only •
new channels found will be stored, and original
channels won’t be overwritten..
Press MENU + UP / DOWN button to ►
select TV.
Press OK + UP / DOWN button to ►
select Channels.
Press OK + UP / DOWN button to ►
select Update Scan.
Press OK button to execute the Update ►
Scan.
27%
Exit Cancel
Statu s : S c a n n i n g .
Analo g C h a n n e l s : 0
Digit a l C h a n n e l s : 0
English
EN
18
Channel Skip
This function enables you to skip the stored •
channels.
Press MENU + UP / DOWN button to ►
select TV.
Press OK + UP / DOWN button to ►
select Channels.
Press OK + UP / DOWN button to ►
select Channel Skip.
Press OK + UP / DOWN button to ►
select the channel you want to skip.
Press OK button to set. A checked icon ►
is a skip one.
A skip channel is skipped when using CH • ^ and
CHv button to browse the channels.
A skip channel can be watch by key-in the
•
program number or select by list.
No signal analog channel is a default skip
•
program.
Exit Back
2 Anal o g - - - - -
3 Anal o g - - - - -
OK Set
Exit Back
8 0 1 D i g i t a l M o n o s c o p e
8 0 2 D i g i t a l M o v i n g P i c t u . . .
OK Set
8 0 3 D i g i t a l H 2 6 4 _ 1 2
8 0 4 D i g i t a l H 2 6 4 _ 2
8 0 5 D i g i t a l H 2 6 4 _ 4
8 0 6 D i g i t a l H 2 6 4 _ 8
8 0 7 D i g i t a l M P E G 2
9 0 1 A n a l o g A R D
Analog Manual Scan (Analog
TV only)
Analog Manual Scan lets you manually add an •
analog channel to your channel list.
Press MENU + UP / DOWN button to ►
select TV.
Press OK + UP / DOWN button to ►
select Channels.
Press OK + UP / DOWN button to ►
select Analog Manual Scan.
Press OK button to display the ATV or ►
TV channel info.
Press UP / DOWN button to select an ►
item.
Press OK / RIGHT button to scan up or ►
down.
Exit Back
Sea r c h f o r anal o g c h a n n els
Sca n U p
Sca n D o w n
EN
19
Channel Edit
To edit a channel number and name of a •
channel.
Press MENU + UP / DOWN button to ►
select TV.
Press OK + UP / DOWN button to ►
select Channels.
Press OK + UP / DOWN button to ►
select Channel Edit.
Press OK + UP / DOWN button to ►
select the channel.
Press OK button to display the change ►
dialog.
Exit Back
OK Set
2 A n a l o g - - - - -
3 A n a l o g - - - - -
Exit Back
8 0 1 D i g i t a l M o n o s c o p e
8 0 2 D i g i t a l M o v i n g P i c t u . . .
OK Set
8 0 3 D i g i t a l H 2 6 4 _ 1 2
8 0 4 D i g i t a l H 2 6 4 _ 2
8 0 5 D i g i t a l H 2 6 4 _ 4
8 0 6 D i g i t a l H 2 6 4 _ 8
8 0 7 D i g i t a l M P E G 2
9 0 1 A n a l o g ARD
Channel Sort (Swap)
To sort (swap) two channels. •
Press MENU + UP / DOWN button to ►
select TV.
Press OK + UP / DOWN button to ►
select Channels.
Press OK + UP / DOWN button to ►
select Channel Sort.
Press OK + UP / DOWN button to ►
select the channel.
Press OK button to set. A checked icon ►
displays.
Press UP / DOWN button to select ►
another channel.
Press OK button to swap these two ►
channels.
Exit Back
2 Analog - - - - -
3 Analog - - - - -
OK Set
Exit Back
8 0 1 D i g i t a l M o n o s c o p e
8 0 2 D i g i t a l M o v i n g P i c t u . . .
OK Set
8 0 3 D i g i t a l H 2 6 4 _ 1 2
8 0 4 D i g i t a l H 2 6 4 _ 2
8 0 5 D i g i t a l H 2 6 4 _ 4
8 0 6 D i g i t a l H 2 6 4 _ 8
8 0 7 D i g i t a l M P E G 2
9 0 1 A n a l o g ARD
20
Press MENU + UP / DOWN button to ►
select TV.
Press OK + UP / DOWN button to ►
select Channels.
Press OK + UP / DOWN button to ►
select Analog Ch Fine Tune.
Press OK + UP / DOWN button to ►
select the channel you want to ne tune.
Press OK button to the Fine Tune ►
dialogue.
Press LEFT / RIGHT to ne tune the ►
frequency.
Press OK button to save. ►
Appendix
Alphabet and numeric numbers mapping table
on the Remote control
To edit a channel number and name of a channel •
via the Remote control:
0: . @ 0
1: _ - 1
2: ABCabc2
3: DEFdef3
4: GHIghi4
5:JKLjkl5
6:MNOmno6
7:PQRSpqrs7
8:TUVtuv8
9:WXYZwxyz9
Decoder (Analog TV only)
To edit a channel decode. •
Press MENU + UP / DOWN button to ►
select TV.
Press OK + UP / DOWN button to ►
select Channels.
Press OK + UP / DOWN button to ►
select Decoder.
Press OK + UP / DOWN button to ►
select the channel.
Press OK button to set. A checked icon ►
displays.
Analog Ch Fine Tune (Analog
TV only)
Normally ne tuning is only necessary if •
reception is poor.
Exit Back
2 A n a l o g - - - - -
3 A n a l o g - - - - -
OK Set
OK Adjust Exit Back
2 - - - - - 4 6 . 9 8 7 M H z
3 - - - - - 119.98 5 M H z
21
on MHEG 5 application – normally it displays
nothing. Teletext is compliant with MHEG5
behavior, it will not show “No Teletext” when
country is U.K.
To display Teletext. Press the TELETEXT
button.
To change the Teletext
page.
Press the UP / DOWN
button.
To change the Teletext
subpage.
Press the SUBPAGE, and
number button.
To stop the automatic
page change.
Press the HOLD button.
To return to the
Teletext index page.
Press the INDEX button.
To reveal the Teletext
information.
Press the REVEAL button.
To display the Teletext
subtitle.
Press the SUBTITLE
button.
To change different
Teletext content.
Press the one of four
buttons.
Color key priority: TOP >
FLOF > Favorite page >
Default color key.
8. Feature setting
highlights:
Menu Features page provides Menu Language,
Picture format, Time, Subtitle, Teletext Language,
Common Interface, and Reset Default.
Press MENU button to display the menu. ►
Press UP / DOWN button to select the ►
Features item.
Press OK button enter the Features sub ►
item.
Press MENU button to exit the sub item. ►
Using the Teletext
If the channel support Teletext mode (means
Teletext is provided), user can open the page to
watch some information.
Support Teletext 1.5.
Teletext contents follow broadcast contents,
change Country will not affect the Teletext
contents.
Teletext display full screen.
Teletext page number show in left-up corner,
if have several subpage, will show in up line,
current subpage number show in right-up
corner.
The key teletext button will be handled by
Teletext and MHEG5 component. In MHEG5,
when “no teletext” is transmitted, it depends
22
Press MENU button to display the menu. ►
Press UP / DOWN button to select the ►
Parental item.
Press OK button enter the Parental sub ►
item.
Press number 0-9 button to key-in the ►
correct password to select the sub item.
(The default password is 0000.)
Press MENU button to exit the sub item. ►
Channel Block
Blocks any channels that you do not want to •
watch or that you do not want your children to
watch
Default value is non-block.
•
Channel with a lock icon is a blocked channel. •
A blocked channel can be un-locked temporarily •
after key-in the correct password.
Press the OK button to display the ►
password dialog.
Press the 0-9 buttons to key-in the ►
correct password.
Using the EPG
This system has an Electronic Program Guide
(EPG) to help your navigation through all the
possible viewing options.
The EPG supplies information such as program
listings, start and end times for all available
services. In addition, detailed information about
the program is often available in the EPG
(the availability and amount of these program
details will vary, depending on the particular
broadcaster).
This function can be used only when the EPG
information is broadcasted by broadcasting
companies.
Press the EPG button to display the EPG. ►
The functions of color keys are optional. »
Note
Can’t display EPG when TV channel is Analog •
channel.
Parental Menu setting:
Menu Parental page provides Channel Block,
Parental Guidance, Set Password and Key Lock
settings.
23
Input Block
To lock an input source. •
Default value is non-block. •
Input source with a lock icon • is a blocked
input source.
A blocked input source can be un-locked
•
temporarily after key-in the correct password.
Press the OK button to display the ►
password dialog.
Press the 0-9 buttons to key-in the ►
correct password.
All input source and locked channels will •
temporarily un-lock
After powering off and on the TV set, the un-
•
locked input source will be locked again.
Press UP / DOWN button to select the ►
input source.
Press OK button to set. A checked icon ►
is a block one.
When user not input password to un-lock any •
channels and input source, press OK button to
lock/unlock the input source in Parental Menu,
the screen will lock/unlock in real time.
When user input correct password in the
•
password dialog to temporarily un-locked, and
not powering off and on the TV set, during
this period, press OK button to lock/unlock
the input source in Parental Menu, the screen
will not lock/unlock in real time.
All locked channels and input source will •
temporarily un-lock.
After powering off and on the TV set, the un-
•
locked channels will be locked again.
Press UP / DOWN button to select the ►
channel.
Press OK button to set. A checked ►
channel is a block one.
When user not input password to un-lock any •
channels and input source, press OK button to
lock/unlock the channel in Parental Menu, the
screen will lock/unlock in real time.
When user input correct password in the
•
password dialog to temporarily un-locked, and
not powering off and on the TV set, during this
period, press OK button to lock/unlock the
channel in Parental Menu, the screen will not
lock/unlock in real time.
Parental Guidance
This function operates according to ►
information from the broadcasting
station.
Therefore if the signal has no this ►
information, this function does not
operate.
Prevent children from watching adult’s TV ►
programs by the rating limit set.
Age Rating :
To adjust the age rating based on age: None, 4,
5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17 and 18.
24
9. Pixel policy
Philips strives to deliver the highest quality
products. We use some of the industry's
most advanced manufacturing processes and
practice stringent quality control. However, pixel
or sub pixel defects on the TFT LCD panels
used in flat panel monitors are sometimes
unavoidable. No manufacturer can guarantee
that all panels will be free from pixel defects,
but Philips guarantees that any monitor with
an unacceptable number of defects will be
repaired or replaced under warranty. This notice
explains the different types of pixel defects and
defines acceptable defect levels for each type. In
order to qualify for repair or replacement under
warranty, the number of pixel defects on a TFT
LCD panel must exceed these acceptable levels.
For example, no more than 0.0004% of the sub
pixels on a 19" XGA monitor may be defective.
Furthermore, Philips sets even higher quality
standards for certain types or combinations
of pixel defects that are more noticeable than
others. This policy is valid worldwide.
Pixels and Sub pixels
A pixel, or picture element, is composed of
three sub pixels in the primary colors of red,
green and blue. Many pixels together form an
image. When all sub pixels of a pixel are lit,
the three colored sub pixels together appear
as a single white pixel. When all are dark, the
three colored sub pixels together appear as a
single black pixel. Other combinations of lit and
dark sub pixels appear as single pixels of other
colors.
Set Password
To change the password. •
The default password is 0000. •
Input a 4-digit password. Be sure to remember •
this number!
Re-enter new password for conrm.
•
Clean All
To reset all parental control settings to the •
default values.
A conrm diagram displays before execute.
•
OAD update:
If using digital broadcast, your TV would
automatically receive software updates. When
it is active, you will receive a message on your
screen asking you to update your software. Just
follow the instruction on the message to make
your choice and complete the settings.
25
Note
A red or blue bright dot must be more than 50
percent brighter than neighboring dots while
a green bright dot is 30 percent brighter than
neighboring dots.
Black Dot Defects Black dot defects appear as
pixels or sub pixels that are always dark or 'off'.
That is, a dark dot is a sub-pixel that stands
out on the screen when the monitor displays a
light pattern. These are the types of black dot
defects:
Proximity of Pixel Defects
Because pixel and sub pixels defects of the
same type that are near to one another may be
more noticeable, Philips also specifies tolerances
for the proximity of pixel defects.
Pixel Defect Tolerances
In order to qualify for repair or replacement
due to pixel defects during the warranty period,
a TFT LCD panel in a Philips flat panel monitor
must have pixel or sub pixel defects exceeding
the tolerances listed in the following tables.
Types of Pixel Defects
Pixel and sub pixel defects appear on the
screen in different ways. There are two
categories of pixel defects and several types of
sub pixel defects within each category.
Bright Dot Defects Bright dot defects appear
as pixels or sub pixels that are always lit or 'on'.
That is, a bright dot is a sub-pixel that stands
out on the screen when the monitor displays a
dark pattern. There are the types of bright dot
defects:
One lit red, green or blue sub pixel
Two adjacent lit sub pixels:
- Red + Blue = Purple
- Red + Green = Yellow
- Green + Blue = Cyan (Light Blue)
Three adjacent lit sub pixels (one white pixel)
26
BRIGHT DOT DEFECTS ACCEPTABLE LEVEL
MODEL 201T1/221T1/231T1 plus
1 lit subpixel 3
2 adjacent lit subpixels 1
3 adjacent lit subpixels (one white pixel) 0
Distance between two bright dot defects* >15mm
Total bright dot defects of all types 3
BLACK DOT DEFECTS ACCEPTABLE LEVEL
MODEL 201T1/221T1/231T1 plus
1 dark subpixel 5 or fewer
2 adjacent dark subpixels 2 or fewer
3 adjacent dark subpixels 0
Distance between two black dot defects* >15mm
Total black dot defects of all types 5 or fewer
TOTAL DOT DEFECTS ACCEPTABLE LEVEL
MODEL 201T1/221T1/231T1 plus
Total bright or black dot defects of all types 5 or fewer
Note
1 or 2 adjacent sub pixel defects = 1 dot defect
The monitor is ISO9241-307 compliant.
27
TV channel issues
Previously installed channels do not appear in
the channel list:
Check that the correct channel list is •
selected.
No digital channels were found during the
installation:
Check that the TV supports DVB-T or •
DVB-C in your country. See the listed
countries on the back of the TV.
Picture issues
The TV is on, but there is no picture:
Check that the antenna is properly •
connected to the TV.
Check that the correct device is selected •
as the TV source.
There is sound but no picture:
Check that the picture settings are •
correctly set.
There is poor TV reception from an antenna
connection:
Check that the antenna is properly •
connected to the TV.
Loud speakers, unearthed audio devices, •
neon lights, high buildings and other large
objects can inuence reception quality.
If possible, try to improve the reception
quality by changing the antenna direction
or moving devices away from the TV.
If reception on only one channel is poor, •
ne tune this channel.
There is poor picture quality from connected
devices:
Check that the devices are connected •
properly.
Check that the picture settings are •
correctly set.
The TV did not save your picture settings:
Check that the TV location is set to the •
home setting. This mode offers you the
exibility to change and save settings.
10. Troubleshooting
This section describes commonly encountered
issues and accompanying solutions.
General TV issues
The TV does not switch on:
Disconnect the power cable from the •
power outlet. Wait for one minute then
reconnect it.
Check that the power cable is securely •
connected.
The remote control is not working properly:
Check that the remote control batteries •
are correctly inserted according to the
+/- orientation.
Replace the remote control batteries if •
they are at or weak.
Clean the remote control and TV sensor •
lens.
The standby light on the TV blinks red:
Disconnect the power cable from the •
power outlet. Wait until the TV cools
down before reconnecting the power
cable. If the blinking reoccurs, contact
Philips Consumer Care.
The TV menu is in the wrong language
Change the TV menu to your preferred •
language.
When turning the TV on/off/to standby, you
hear a creaking sound from the TV chassis:
No action is required. The creaking sound •
is normal expansion and contraction of
the TV as it cools and warms up. This
does not impact performance.
28
Thepicturedoesnottthescreen;itistoo
big or too small:
Try using a different picture format. •
The picture position is incorrect:
Picture signals from some devices may •
not t the screen correctly. Check the
signal output of the device.
Sound issues
There is a picture but no sound from the TV:
Note
If no audio signal is detected, the TV •
automatically switches the audio output off —
this does not indicate malfunction.
Check that all cables are properly •
connected.
Check that the volume is not set to 0. •
Check that the sound is not muted. •
There is a picture but the sound quality is
poor:
Check that the sound settings are •
correctly set.
There is a picture but sound comes from
one speaker only:
Verify that sound balance is set to the •
centre.
HDMI connection issues
There are problems with HDMI devices:
Note that HDCP support can delay the •
time taken for a TV to display content
from a HDMI device.
If the TV does not recognise the HDMI •
device and no picture is displayed, try
switching the source from one device to
another and back again.
If there are intermittent sound •
disruptions, check that output settings
from the HDMI device are correct.
If a HDMI-to-DVI adaptor or HDMI to •
DVI cable is used, check that an additional
audio cable is connected to AUDIO L/R
or AUDIO IN (mini-jack only).
Computer connection issues
The computer display on the TV is not stable:
Check that a supported resolution and •
refresh rate is selected on the computer.
Set the TV picture format to unscaled. •
Others
When should I use SmartContrast feature?
SmartContrast feature is designed for •
enhancing movies as well as playing some
games, as it enhances contrast ratio in
dark moving scenes.
Factory default is “Off” •
For ofce usage or internet applications it •
is recommended to turn SmartContrast
“Off
Power LED turn on for Auto program update
In a case of auto s/w update, the unit will •
be turned on automatically for software
updates. There will be no video or audio
when doing the updates. The unit will also
be returned to normal when software
updates are completed.
Timing setting:
Suggest do the time setting after scan •
TV channels to synchronize the time
zone. This will facilitate any auto software
updates being active in the right and
designated time period provided by the
TV broadcasting system makers.
29
Contact us
If you cannot resolve your problem, refer to
the FAQs for this TV at www.philips.com/
support.
If the problem remains unresolved, contact
Philips Consumer Care in your country as
listed in this User Manual.
Warning
Do not attempt to repair the TV yourself. This •
may cause severe injury, irreparable damage to
your TV or void your warranty.
Note
Make a note of your TV model and serial •
number before you contact Philips. These
numbers are printed on the back of the TV and
on the packaging.