Table of Contents
Philips AE5010/05 User Manual
Displayed below is the user manual for AE5010/05 by Philips which is a product in the Radios category. This manual has pages.
Related Manuals
Register your product and get support at
www.philips.com/welcome
EN User manual
AE5010
AE5010_05_UM_V1.3.indd 1 8/9/2011 10:35:15 AM
2EN
AE5010_05_UM_V1.3.indd 2 8/9/2011 10:35:15 AM
3EN
Contents
1 Important 5
Safety 5
Notice 6
2 Your FM/DAB radio 8
Introduction 8
What’s in the box 8
Overview of the main unit 9
3 Get started 11
Prepare FM/DAB antenna 11
Connect power 11
Turn on 13
Adjust the volume level 13
4 Listen to FM radio 14
Tune to FM radio 14
Store FM stations manually 14
Select a preset FM radio station 15
Use FM menu 15
5 Listen to DAB radio 16
Tune to DAB radio 16
Change DAB station 16
Scan DAB radio stations 17
Display station information 17
Store DAB stations manually 18
Select a preset DAB radio station 18
Use DAB menu 19
Contents
AE5010_05_UM_V1.3.indd 3 8/9/2011 10:35:15 AM
5
1 Important
Safety
• The device shall not exposed to dripping or splashing.
• Donoplaceanysourceofdangeronthedevice(e.g.liquidlledobjects.lit
candles).
• Where the mains plug or an appliance coupler is used as the disconnect
device, the disconnect device shall remain readily operable.
Warning
•Never remove the casing of this unit.
•Never lubricate any part of this unit.
•Placethisunitonaat,hardandstablesurface.
•Never place this unit on other electrical equipment.
•Onlyusethisunitindoors.Keepthisunitawayfromwater,moistureandliquid-lledobjects.
•Keepthisunitawayfromdirectsunlight,nakedamesorheat.
Hearing safety
Listen at a moderate volume.
• Using headphones at a high volume can impair your hearing. This product can
produce sounds in decibel ranges that may cause hearing loss for a normal
person, even for exposure less than a minute. The higher decibel ranges are
offered for those that may have already experienced some hearing loss.
• Sound can be deceiving. Over time your hearing ‘comfort level’ adapts to
higher volumes of sound. So after prolonged listening, what sounds ‘normal’
can actually be loud and harmful to your hearing. To guard against this, set
your volume to a safe level before your hearing adapts and leave it there.
To establish a safe volume level:
• Set your volume control at a low setting.
• Slowly increase the sound until you can hear it comfortably and clearly,
without distortion.
EN
AE5010_05_UM_V1.3.indd 5 8/9/2011 10:35:15 AM
6
Listen for reasonable periods of time:
• Prolonged exposure to sound, even at normally ‘safe’ levels, can also cause
hearing loss.
• Be sure to use your equipment reasonably and take appropriate breaks.
Be sure to observe the following guidelines when using your headphones.
• Listen at reasonable volumes for reasonable periods of time.
• Be careful not to adjust the volume as your hearing adapts.
• Do not turn up the volume so high that you can’t hear what’s around you.
• You should use caution or temporarily discontinue use in potentially
hazardous situations. Do not use headphones while operating a motorized
vehicle,cycling,skateboarding,etc.;itmaycreateatrafchazardandisillegal
in many areas.
Notice
Anychangesormodicationsmadetothisdevicethatarenotexpresslyapproved
by Philips Consumer Lifestyle may void the user’s authority to operate the
equipment.
This product complies with the radio interference requirements of the European
Community.
Your product is designed and manufactured with high quality materials and
components, which can be recycled and reused.
When this crossed-out wheeled bin symbol is attached to a product it means that
the product is covered by the European Directive 2002/96/EC.
Please inform yourself about the local separate collection system for electrical and
electronic products.
EN
AE5010_05_UM_V1.3.indd 6 8/9/2011 10:35:16 AM
7
Please act according to your local rules and do not dispose of your old products
with your normal household waste. Correct disposal of your old product helps to
prevent potential negative consequences for the environment and human health.
Your product contains batteries covered by the European Directive 2006/66/EC,
which cannot be disposed with normal household waste.Please inform yourself
about the local rules on separate collection of batteries because correct disposal
helps to prevent negative consequences for the environmental and human health.
Environmental information
All unnecessary packaging has been omitted. We have tried to make the packaging
easy to separate into three materials: cardboard (box), polystyrene foam (buffer)
and polyethylene (bags, protective foam sheet.)
Your system consists of materials which can be recycled and reused if disassembled
by a specialized company. Please observe the local regulations regarding the
disposal of packaging materials, exhausted batteries and old equipment.
EN
AE5010_05_UM_V1.3.indd 7 8/9/2011 10:35:16 AM
8
2 Your FM/DAB radio
Congratulationsonyourpurchase,andwelcometoPhilips!Tofullybenetfrom
the support that Philips offers, register your product at www.philips.com/welcome.
Introduction
With this unit, you can enjoy both FM radio and Digital Audio Broadcasting (DAB)
radio.
Digital Audio Broadcasting (DAB), is a way of broadcasting radio digitally through
a network of transmitters. It provides you with more choice, better sound quality
and more information.
What’s in the box
Check and identify the contents of your package:
• Main unit
• AC adaptor
• User manual
EN
AE5010_05_UM_V1.3.indd 8 8/9/2011 10:35:16 AM
9
Overview of the main unit
a FM/DAB antenna
• Improve FM/DAB reception.
b Display panel
• Display the status.
c +/-
• Adjust volume.
d
• Turn on or off the unit.
e /
• Tune to an FM radio station.
• Go to a DAB service list.
• Scroll through menu list.
f
• Socket for the headphone.
g PRESET
• Program radio stations.
• Select a preset radio station.
SCAN
INFO
DAB/FM ENTERPRESET
hijk f
g
b
c
d
e
a
EN
AE5010_05_UM_V1.3.indd 9 8/9/2011 10:35:17 AM
10
h ENTER
• Conrmaselection.
i DAB/FM
• Select DAB or FM radio.
j INFO
• Display DAB station information.
• Access DAB/FM menu.
k SCAN
• Search FM/DAB radio stations.
EN
AE5010_05_UM_V1.3.indd 10 8/9/2011 10:35:17 AM
11
3 Get started
Caution
•Use of controls or adjustments or performance of procedures other than herein may result in
hazardous radiation exposure or other unsafe operation.
Always follow the instructions in this chapter in sequence.
If you contact Philips, you will be asked for the model and serial number of this
apparatus. The model number and serial number are on the back of the apparatus.
Write the numbers here:
Model No. __________________________
Serial No. ___________________________
Prepare FM/DAB antenna
For optimal reception, fully extend and adjust the position of the FM/DAB antenna.
Tip
•Position the antenna as far away as possible from your TV, VCR or other radiation source to prevent
interference.
Connect power
You can use this radio player on AC power or battery power.
Battery Life (Approx. hours)
When using FM DAB
alkaline R6 (size AA) 12 12
EN
AE5010_05_UM_V1.3.indd 11 8/9/2011 10:35:17 AM
12
Option 1: AC power
Caution
•Risk of product damage! Ensure that the power supply voltage corresponds to the voltage printed
on the back or the underside of the product.
•Risk of electric shock! When you unplug the AC adaptor, always pull the plug from the socket.
Never pull the cord.
•UseonlytheACadaptorspeciedbythemanufacturerorsoldwiththisunit.
Note
•The type plate is on the back of the apparatus.
1 Connect one end of the AC adaptor to the DC socket on the main unit.
2 Connect the other end of the AC adaptor to the wall outlet.
Option 2: Battery power
Caution
•Riskofexplosion!Keepbatteriesawayfromheat,sunshineorre.Neverdiscardbatteriesinre.
•Do not mix batteries (old and new or carbon and alkaline, etc.).
•Remove batteries if they are exhausted or if the unit is not to be used for a long time.
1 Open the battery compartment at the back of the unit.
EN
AE5010_05_UM_V1.3.indd 12 8/9/2011 10:35:17 AM
13
2 Insert 4 AA size batteries (not supplied) with correct polarity (+/-) as
indicated, then close the battery compartment.
3 The unit is ready to operate.
Note
•Batteries contain chemical substances, so they should be disposed of properly.
Turn on/off
1 Press .
»[Welcome to Philips Audio] is displayed.
»The radio goes to the last selected source.
To turn off the unit:
1 Press again .
Adjust the volume level
1 During play, press +/- to increase/decrease the volume level.
EN
AE5010_05_UM_V1.3.indd 13 8/9/2011 10:35:17 AM
14
4 Listen to FM radio
Tune to FM radio
1 Press DAB/FM repeatedly to select FM radio.
2 Press / to tune to a radio station.
Search FM radio stations
1 Tune to FM radio.
2 Press and hold / for more than two seconds to start searching stations.
»The FM tuner tunes to a station with strong reception automatically.
3 Repeatstep2ifnecessaryuntilyoundthedesiredstation.
Store FM stations manually
You can program a maximum of 10 preset FM radio stations.
1 Tune to your desired FM station.
2 Press and hold PRESET for two second,
»The preset number is displayed.
3 Press / to select the desired preset number.
4 Press ENTERtoconrmtheselection.
»The stored radio frequency and number are displayed.
Note
•To overwrite a preset station, store another station in its place.
EN
AE5010_05_UM_V1.3.indd 14 8/9/2011 10:35:17 AM
15
Select a preset FM radio station
1 Press DAB/FM repeatedly to select FM radio.
2 Press PRESET to enter the preset channel list.
3 Press / tondyourdesiredstation.
4 Press ENTERtoconrmtheselection.
Note
•When you go through the preset station list, if no button is pressed within three seconds, the radio
tunes to the showed preset station.
Use FM menu
1 In FM mode, press and hold INFO to enter the FM menu.
2 Press / to scroll the menu options:
• [Audio setting]
• [System]
3 To select an option, press ENTER.
4 Repeat step 2-3 if sub-option is available under one option.
[Audio setting]
This function enables you to select mono or stereo
• [Forced mono] Select mono broadcast.
• [Stereo allowed] Select stereo broadcast.
[System]
• [Factory reset] Resets all the settings of this radio player to factory
default.
• [SW version] Software version of the radio player is shown.
Note
•If no button is pressed within 10 seconds, the menu exits.
EN
AE5010_05_UM_V1.3.indd 15 8/9/2011 10:35:18 AM
16
5 Listen to DAB radio
Tune to DAB radio
WhenyouentertheDABmodeforthersttime,theradioplayershows[DAB
mode] for two seconds and enters the DAB menu. Press ENTER to start the
scanning. Then station list is retained in memory so the next time the radio player
is switched on, the station scan does not take place.
1 Press DAB/FM repeatedly to select DAB radio.
»A bar graph indicates the progress of the search and the number of
stations found increase as the scan progresses.
A When the scan is completed, the stations are listed in numerical then
alphabetic order.
»First available station is played.
B If there is no DAB coverage currently available
»[No DAB Station] is displayed.
a Change the location or adjust antenna.
b Press SCAN to search again.
Change DAB station
1 Tune to a DAB station.
2 Use / to navigate through available stations.
Number of
Stations found
Progress bar
EN
AE5010_05_UM_V1.3.indd 16 8/9/2011 10:35:18 AM
17
3 Press ENTER to select the station.
Note
•If no button is pressed within three seconds, the radio tunes to the current station automatically.
Scan DAB radio stations
1 When playing a DAB station, or the current station is not available, press
SCAN for more than two seconds.
»The radio player scans all available DAB radio stations and broadcasts
the current station.
Tip
•New stations and services will be added in the DAB broadcast. To make new DAB stations and
services available on your radio player, do the scan on a regular base.
Display station information
1 Tune to a DAB radio station.
2 Press INFO repeatedly to scroll through the following information (if
available):
»Dynamic label segment (DLS)
»Strength
»Program type (PTY)
»Ensemble Name
»Channel and frequency
»Signal error rate
EN
AE5010_05_UM_V1.3.indd 17 8/9/2011 10:35:18 AM
18
»Bit rate and audio status
»Time
Store DAB stations manually
You can store a maximum of 10 preset DAB radio stations.
1 Tune to your desired DAB station.
2 Press and hold PRESET for two seconds.
»[Preset X stored] is displayed.
3 To select a preset number, press / ; then press ENTER toconrmthe
selection.
»The preset number of the saved station is displayed.
Note
•To overwrite a preset station, store another station in its place.
Select a preset DAB radio station
1 Press DAB/FMrepeatedly to select DAB radio.
2 Press PRESET to enter the present channel list.
3 Press / to select a preset number.
4 Press ENTERtoconrmtheselection.
Note
•When you go through the preset station list, if no button is pressed within three seconds, the radio
tunes to the showed preset station.
EN
AE5010_05_UM_V1.3.indd 18 8/9/2011 10:35:18 AM
19
Use DAB menu
1 In DAB mode, press and hold INFO for two seconds to enter the DAB
menu.
2 Press / to scroll the menu options:
• [Station list]
• [System]
• [DRC] (dynamic range control)
• [Manual tune]
• [Full scan]
3 To select an option, press ENTER.
4 Repeat step 2-3 if sub-option is available under one option.
[System]
• [Info] (Software version of the radio player is shown.)
• [Factory reset] (Resets all the settings of this radio player to factory
default.)
• Press’ENTERtoconrmreset.
[DRC]
Dynamic range control (DRC) adds or removes a degree of compensation for the
differences in the dynamic range between radio stations.
• [DRC high] (DRC is switched on; the default setting recommended for
noisy environment.)
• [DRC low] (DRC is set to half normal level.)
• [DRC off] (DRC is switched off.)
[Manual tune]
Itispossibletomanuallytunetoaspecicchannel/frequencyandaddthistothe
station list.
Thisfunctioncanbeusedtoobtaintheoptimumreceptionforaspecicchannel/
frequency, taking into account the position of the aerial.
»Therstlineofthedisplayshowstheselectedchannelanditsfrequency.
Therstlineofthedisplayshowsarectangle.
»A rectangle will be displayed on the second line of the display. The
position of this rectangle indicates the signal strength (the further
towards the right, the greater the signal strength).
EN
AE5010_05_UM_V1.3.indd 19 8/9/2011 10:35:18 AM
20
Tip
•Adjust the position of the antenna to obtain the optimum signal strength.
[Full scan]
Full scan is used to perform a wide range of DAB radio search (outside UK).
Note
•If no button is pressed within 10 seconds, the menu exits.
EN
AE5010_05_UM_V1.3.indd 20 8/9/2011 10:35:18 AM
21
6 Product information
Note
•Product information is subject to change without prior notice.
Tuner (FM)
Tuning Range 87.5 - 108MHz
Tuning grid 50KHz
Tuner (DAB)
Tuning Range 174.928MHz - 239.200MHz (Band III)
EN
AE5010_05_UM_V1.3.indd 21 8/9/2011 10:35:18 AM
22
General information
AC/DC adaptor
- Brand name
- Model
- Input
- Output
PHILIPS
Y06FE-050-1000B
100-240V~ 50/60Hz 0.2A
5V 1000mA
Operation Power Consumption 5W
Standby Power Consumption <1W
Power output 0.3W (10% THD)
Battery AA x 4
Headphone output power 12mW x 2 (32 ohm)
Dimensions
- Main Unit (W x H x D) 317 x 133 x 90 mm
Weight
- Main Unit 0.884kg
EN
AE5010_05_UM_V1.3.indd 22 8/9/2011 10:35:18 AM
23
7 Troubleshooting
Warning
•Never remove the casing of this apparatus.
To keep the warranty valid, never try to repair the system yourself.
If you encounter problems when using this apparatus, check the following points
before requesting service. If the problem remains unsolved, go to the Philips
web site www.philips.com/welcome. When you contact Philips, ensure that the
apparatus is nearby and the model number and serial number are available.
No power
•Ensure that the AC power plug of the unit is connected properly.
•Ensure that there is power at the AC outlet.
•Insert the batteries with their polarities (+/– signs) aligned as indicated.
•Replace the battery.
No sound
•Adjust the volume.
Poor radio reception
•Increase the distance between the unit and your TV or VCR.
•Fully extend the antenna.
EN
AE5010_05_UM_V1.3.indd 23 8/9/2011 10:35:18 AM
24
8 About DAB
About Digital Audio Broadcasting (DAB)
DAB digital radio is a new way of broadcasting radio via a network of terrestrial
transmitters. It provides listeners with more choice and information delivered in
crystal clear, crackle-free sound quality.
–Thetechnologyallowsthereceivertolockontothestrongestsignalitcannd.
– With DAB digital stations there are no frequencies to remember, and sets are
tuned by station name, so there’s no returning on the move.
What is a multiplex?
Digital radio operation is made up of a single block of frequencies called a
multiplex. Each multiplex works within a frequency spectrum, such as Band III for
DAB broadcasts.
DAB BROADCASTERS AND DLS
Each DAB broadcaster (or multiplex operator) also provides text and audio data
services. Some programmes are supported by Dynamic Label Segments (DLS).
This is data which you can read as scrolling text on your DAB radio display. Some
stations transmit the latest news, travel, and weather, what’s on now and next,
website addresses and phone numbers.
For more information on digital radio coverage and services, please visit: www.
drdb.org.
EN
AE5010_05_UM_V1.3.indd 24 8/9/2011 10:35:19 AM
25
AE5010_05_UM_V1.3.indd 25 8/9/2011 10:35:19 AM
26
AE5010_05_UM_V1.3.indd 26 8/9/2011 10:35:19 AM
27
AE5010_05_UM_V1.3.indd 27 8/9/2011 10:35:19 AM
© 2011 Koninklijke Philips Electronics N.V.
All rights reserved.
AE5010_05_UM_V1.4
AE5010_05_UM_V1.3.indd 28 8/9/2011 10:35:19 AM