Table of Contents
Philips CSS5235Y/93 User Manual
Displayed below is the user manual for CSS5235Y/93 by Philips which is a product in the Speaker Sets category. This manual has pages.
Related Manuals
www.philips.com/support
User manual
Always there to help you
Register your product and get support at
Question?
Contact
Philips
CSS5235Y
CSS5235Y_93_UM_V1.0.indb 2 4/24/2015 3:50:42 PM
1
English
EN
Contents
1 Important 2
Safety 2
Care for your product 3
Care of the environment 3
Help and support 3
2 Your product 4
Main unit 4
Remote control 5
Connectors 6
Wireless speakers 6
Wireless subwoofer 7
3 Connect and set up 8
Connect the main unit 8
Charge speakers 8
Pair up with speakers/subwoofer 8
Place speakers 9
Connect to TV 10
Connect audio from TV and
other devices 11
4 Use your product 12
Adjust the volume 12
Choose your sound 12
Play music via Bluetooth 13
Play music via NFC 13
MP3 player 14
USB storage devices 14
Auto standby 15
Apply factory settings 15
5 Update software 15
Check software version 15
Update software via USB 15
6 Productspecications 17
7 Troubleshooting 18
CSS5235Y_93_UM_V1.0.indb 1 4/24/2015 3:50:51 PM
2EN
1 Important
Read and understand all instructions
before you use your product. If damage is
caused by failure to follow instructions, the
warranty does not apply.
Safety
Riskofelectricshockorre!
• Before you make or change any
connections, make sure that all devices
are disconnected from the power
outlet.
• Never expose the product and
accessories to rain or water. Never
place liquid containers, such as vases,
near the product. If liquids are spilt on
or into the product, disconnect it from
the power outlet immediately. Contact
Consumer Care to have the product
checked before use.
• Never place the product and
accessories near naked ames or
other heat sources, including direct
sunlight.
• Never insert objects into the
ventilation slots or other openings on
the product.
• Where the mains plug or an appliance
coupler is used as the disconnect
device, the disconnect device shall
remain readily operable.
• Batteries (battery pack or batteries
installed) shall not be exposed to
excessive heat such as sunshine, re or
the like.
• Disconnect the product from the
power outlet before lightning storms.
• When you disconnect the power cord,
always pull the plug, never the cable.
Riskofshortcircuitorre!
• For identication and supply ratings,
see the type plate at the back or
bottom of the product.
• Before you connect the product to the
power outlet, ensure that the power
voltage matches the value printed on
the back or bottom of the product.
Never connect the product to the
power outlet if the voltage is different.
Riskofinjuryordamagetothisproduct!
• Never place the product or any
objects on power cords or on other
electrical equipment.
• If the product is transported in
temperatures below 5°C, unpack the
product and wait until its temperature
matches room temperature before
connecting it to the power outlet.
• Parts of this product can be made of
glass. Handle with care to avoid injury
and damage.
Riskofoverheating!
• Never install this product in a conned
space. Always leave a space of at least
four inches around the product for
ventilation. Ensure curtains or other
objects never cover the ventilation
slots on the product.
Riskofcontamination!
• Do not mix batteries (old and new or
carbon and alkaline, etc.).
• Danger of explosion if batteries are
incorrectly replaced. Replace only with
the same or equivalent type.
• Remove batteries if they are
exhausted or if the remote control is
not to be used for a long time.
CSS5235Y_93_UM_V1.0.indb 2 4/24/2015 3:50:51 PM
3
English
EN
• Batteries contain chemical substances,
they should be disposed of properly.
Riskofswallowingbatteries!
• The product/remote control may
contain a coin/button type battery,
which can be swallowed. Keep the
battery out of reach of children at all
times! If swallowed, the battery can
cause serious injury or death. Severe
internal burns can occur within two
hours of ingestion.
• If you suspect that a battery has been
swallowed or placed inside any part
of the body, seek immediate medical
attention.
• When you change the batteries, always
keep all new and used batteries out
of reach of children. Ensure that the
battery compartment is completely
secure after you replace the battery.
• If the battery compartment cannot be
completely secured, discontinue use
of the product. Keep out of reach of
children and contact the manufacturer.
This is CLASS II apparatus with double
insulation, and no protective earth
provided.
Care for your product
Use only microber cloth to clean the
product.
Care of the environment
Disposal of your old product
Your product is designed and
manufactured with high quality materials
and components, which can be recycled
and reused.
Do not throw away the product with the
normal household waste at the end of its
life, but hand it in at an ofcial collection
point or recycling. By doing this, you help
to preserve the environment.
Help and support
For extensive online support, visit www.
philips.com/support to:
• download the user manual and the
quick start guide
• watch video tutorials (available only for
selected models)
• nd answers to frequently answered
questions (FAQs)
• email us a question
• chat with our support representative.
Follow the instructions on the website to
select your language, and then enter your
product model number.
Alternatively, you can contact Consumer
Care in your country. Before you contact,
note down the model number and serial
number of your product. You can nd this
information on the back or bottom of your
product.
CSS5235Y_93_UM_V1.0.indb 3 4/24/2015 3:50:52 PM
4EN
2 Your product
Congratulations on your purchase, and
welcome to Philips! To fully benet from
the support that Philips offers, register your
product at www.philips.com/welcome.
Main unit
The main unit of this product is comprised
of left and right base speakers.
a LED indication
Red LED
• Lights up when the main unit is
switched to standby.
White LED
• Lights up when the main unit is
switched on.
• Blinks once each time you press a
button on the remote control.
• Blinks twice when Dolby Digital
audio is input.
e
d
c
a
b
f
• Blinks three times when DTS audio
is input.
• Blinks continuously when no
audio from the selected HDMI
ARC source is detected, or when
an unsupported audio format is
detected.
Blue LED
• Lights up when you switch to
Bluetooth mode and Bluetooth
devices are paired.
• Blinks when you switch to
Bluetooth mode and Bluetooth
devices are not paired.
b NFC tag
Tap the NFC-enabled device on the
tag for Bluetooth connection.
c (Standby-On)
Switch the main unit on or to standby.
d
Switch to Bluetooth mode.
e
Toggle through all sources.
f Volume +/-
Increase or decrease volume.
CSS5235Y_93_UM_V1.0.indb 4 4/24/2015 3:50:53 PM
5
English
EN
Remote control
This section includes an overview of the
remote control.
a (Standby-On)
• Switch the main unit on or to
standby.
b Source buttons
COAX: Switch your audio source to
the coaxial connection.
OPTICAL: Switch your audio source
to the optical connection.
AUX: Switch your audio source to the
connection of an external device with
3.5mm jack or with red/white audio
jacks.
b
a
c
d
f
h
i
e
g
j
USB: Switch to USB mode.
Bluetooth: Switch to Bluetooth
mode; Press and hold three seconds
to break the current Bluetooth
connection.
HDMI ARC: Switch your source to
HDMI ARC connection.
c /
Skip to the previous or next track
in USB mode and Bluetooth mode
(only for AVRCP-supported Bluetooth
devices).
d
Start, pause or resume play in USB
mode and Bluetooth mode ( only for
AVRCP-supported Bluetooth devices).
e BASS +/-
Increase or decrease bass.
f Volume control
• +/-: Increase or decrease volume.
• : Mute or restore volume.
g Sound mode control
VOICE: Select voice clarity sound
mode.
MUSIC: Select stereo sound mode.
MOVIE: Select surround sound mode.
h AUDIO SYNC +/-
Increase or decrease audio delay.
i NIGHT ON/OFF
Turn night mode on or off.
j TREBLE +/-
Increase or decrease treble.
CSS5235Y_93_UM_V1.0.indb 5 4/24/2015 3:50:54 PM
6EN
Connectors
This section includes an overview of the
connectors available on this product.
a TO R SPEAKER
Connect to the right base speaker.
b DC IN
Connect to the power supply.
c TO L SPEAKER
Connect to the left base speaker.
d COAXIAL
Connect to a coaxial audio output on
the TV or a digital device.
e
• Connect to a USB storage device
for audio media play.
• Upgrade software of this product.
• Charge a USB device.
f OPTICAL
Connect to an optical audio output on
the TV or a digital device.
g AUDIO IN
Audio input from, for example, an MP3
player (3.5mm jack).
a cb d ef g
h
h TO TV - HDMI OUT (ARC)
Connect to the HDMI (ARC) input on
the TV.
Wireless speakers
This product comes with a pair of wireless
surround speakers.
* The illustration above is for either of
wireless surround speakers.
a LED indicaton
Red LED
• Lights up when the battery
capacity is less than 30% remaining
(undocked from the main unit).
• Blinks when the battery capacity is
less than 10% remaining (undocked
from the main unit).
• If the speaker is not wirelessly
connected to the main unit,
the LED blinks red and orange
alternatively.
White LED
• Lights up when the battery capacity
is full or more than 30% remaining
(undocked from the main unit).
• Lights up when the speaker is
wirelessly connected to the main
unit (undocked from the main unit).
a b
CSS5235Y_93_UM_V1.0.indb 6 4/24/2015 3:50:55 PM
7
English
EN
Orange LED
• Lights up when the surround
speaker is being charged (only for
the wireless speaker docked onto
the main unit).
• If the speaker is not wirelessly
connected to the main unit,
the LED blinks red and orange
alternatively.
b
• Switch the surround speaker on.
• The surround speaker
automatically turns off after
4 minutes of being wirelessly
disconnected from the main unit.
Wireless subwoofer
This product comes with a wireless
subwoofer.
a CONNECT (connect)
Press to to enter the pairing mode for
the subwoofer.
b Subwoofer indicator
• When the power is turned on, the
indicator lights up.
c
a
b
• During wireless pairing between
the subwoofer and the main unit,
the indicator blinks white quickly.
• When the pairing succeeds, the
indicator lights up white.
• When the pairing fails, the indicator
blinks white slowly.
• When wireless connection is
disconnected for 4 minutes, the
indicator turns off.
c AC MAINS~
Connect to the power supply.
CSS5235Y_93_UM_V1.0.indb 7 4/24/2015 3:50:55 PM
8EN
3 Connect and set
up
This section helps you connect this
product to a TV and other devices, and
then set it up.
For information about the basic
connections of this product and
accessories, see the quick start guide.
Note
• For identication and supply ratings,
see the type plate at the back or
bottom of the product.
• Before you make or change any
connections, make sure that all devices
are disconnected from the power
outlet.
Connect the main unit
With the supplied DIN cable, connect the
left base speaker to the right base speaker
as main unit. See the quick start guide for
details.
Charge speakers
If the wireless surround speaker is
undocked from the main unit, its battery
level is indicated by the LED on the
wireless speaker.
• Light up white: full battery or more
than 30% capacity remaining
• Light up red: low battery level, less
than 30% remaining
• Blink red: near empty, less than 10%
remaining
1 Dock the left and right wireless
speakers onto the main unit (the left
and right base speakers) to charge the
speakers.
2 Turn on the main unit.
» During charging, the orange LED
on the wireless speaker lights up.
» When fully charged, the orange
LED on the wireless speaker turns
off.
Note
• It may take around 3 hours to fully
charge the speakers.
Pair up with speakers/
subwoofer
The wireless speakers and subwoofer
automatically pair up with the main unit
(left and right base speakers) for wireless
connection when you turn on the main unit,
the speakers and the subwoofer.
If no audio from the wireless speakers and
subwoofer can be heard, do the following
for pairing.
CSS5235Y_93_UM_V1.0.indb 8 4/24/2015 3:50:56 PM
9
English
EN
Pair up with the speakers
1 Turn on the main unit and the
surround wireless speakers.
» If the connection to the main unit
is lost, the red and orange LEDs
on the wireless speaker blink
alternatively.
2 Dock the left and right wireless
speakers onto the main unit (the left
and right base speakers) to pair up
automatically.
» If the pairing is successful, the
orange LED on the wireless
speaker lights up for ve seconds.
» If the pairing fails, the red and
orange LEDs on the wireless
speaker blinks alternatively.
3 If the paring fails, re-dock the wireless
speakers onto the main unit.
Pair up with the subwoofer
1 Turn on the main unit, and the
subwoofer.
» If the connection to the main
unit is lost, the white LED on the
subwoofer blinks slowly.
2 Press the CONNECT (connect)
button on the subwoofer to enter the
pairing mode.
» The white LED on the subwoofer
blinks quickly.
3 In OPTICAL mode (press OPTICAL)
, within six seconds, on the remote
control, press twice then Volume +
once, and then hold down BASS +.
» If the pairing succeeds, the white
LED on the subwoofer lights up.
» If the pairing fails, the white LED
on the subwoofer blinks slowly.
4 If the pairing fails, repeat the steps
above.
Note
• After the subwoofer is manually
connected to the main unit, pair the
surround speakers with the main unit
again for re-connection.
Place speakers
For best sound effect, position all the
speakers towards the seating position and
place them close to your ear level (seated).
Note
• Surround sound depends on factors
such as room shape and size, type of
wall and ceiling, windows and reective
surfaces, and speaker acoustics.
Experiment with the speaker positions
to nd the optimum setting for you.
SUB
WOOFER
RL
CSS5235Y_93_UM_V1.0.indb 9 4/24/2015 3:50:56 PM
10 EN
Follow these general guidelines for
speakers placement.
1 Seating position:
This is the center of your listening area.
2 Place the main unit (left and right
base speakers) in front of the seating
position.
3 L/ R surround speakers (left/right):
Place the rear surround speakers to
the left and right side of your seating
position, either in line with it or slightly
behind it.
4 SUBWOOFER (subwoofer):
Place the subwoofer at least one
meter to the left or right of the TV.
Leave about 10-centimeter clearance
from the wall.
Dock the surround speakers
You can also dock your surround speakers
onto the main unit to listen to audio, for
example, watching TV shows and news.
Connect to TV
Connect this product to a TV. You can listen
to audio from TV programs through the
speakers of this product.
Connect to TV through HDMI (ARC)
Best quality audio
This product supports HDMI with Audio
Return Channel (ARC). If your TV is HDMI
ARC compliant, you can hear the TV audio
through the speakers of this product by
using a single HDMI cable.
1 Using a High Speed HDMI cable,
connect the HDMI OUT (ARC)
connector on the right base speaker
to the HDMI ARC connector on the
TV.
• The HDMI ARC connector on the
TV might be labeled differently. For
details, see the TV user manual.
2 On your TV, turn on HDMI-CEC
operations. For details, see the TV user
manual.
Note
• If your TV is not HDMI ARC compliant,
connect an audio cable to hear the
TV audio through the speakers of this
product (see 'Connect audio from TV
and other devices' on page 11).
• If your TV has a DVI connector, you
can use an HDMI/DVI adapter to
connect to TV. However, some of the
features may not be available.
TV
CSS5235Y_93_UM_V1.0.indb 10 4/24/2015 3:50:56 PM
11
English
EN
Connect audio from TV and
other devices
Play audio from TV or other devices
through the speakers of this product.
Use the best quality connection available
on this product, TV, and other devices.
Note
• When this product and TV are
connected through HDMI ARC, an
audio connection is not required.
Option 1: Connect audio through a
digital optical cable
Best quality audio
1 Using an optical cable, connect the
OPTICAL connector on the right
base speaker of this product to the
OPTICAL OUT connector on the TV
or other device.
• The digital optical connector might
be labeled SPDIF or SPDIF OUT.
TV
Option 2: Connect audio through a
digital coaxial cable
Best quality audio
1 Using a coaxial cable, connect the
COAXIAL connector on the right
base speaker of this product to the
COAXIAL/DIGITAL OUT connector
on the TV or other device.
• The digital coaxial connector might
be labeled DIGITAL AUDIO OUT.
Option 3: Connect audio through
analog audio cables
Basic quality audio
1 Using an analog cable, connect the
AUDIO IN (3.5mm jack) on the right
base speaker of this product to the
AUDIO OUT connectors (red and
white) on the TV or other device.
2 Press once or two times AUX on the
remote control until higher volume is
heard.
AUDIO OUT
RL
CSS5235Y_93_UM_V1.0.indb 11 4/24/2015 3:50:57 PM
12 EN
4 Use your
product
This section helps you use this product to
play audio from connected devices.
Before you start
• Make the necessary connections
described in the quick start guide and
the user manual.
• Switch this product to the correct
source for other devices.
Adjust the volume
1 Press Volume +/- to increase or
decrease a volume level.
• To mute sound, press .
• To restore the sound, press
again or press Volume +/-.
» If volume is set to the maximum
or minimum, the white LED on the
right base speaker blinks two times.
Choose your sound
This section helps you choose the ideal
sound for your video or music.
Sound mode
Select predened sound modes to suit
your video or music.
• Press MOVIE to create a surround
listening experience. Ideal for watching
movie.
• Press MUSIC to create stereo sound.
Ideal for listening to music.
• Press VOICE to create sound effect
which makes human voice more clear
and outstanding for listening.
Equalizer
Change the high frequency (treble) and
low frequency (bass) settings of this
product.
1 Press TREBLE +/- or BASS +/- to
change the frequency.
» If the treble or bass is set to the
maximum or minimum, the white
LED on the right base speaker blinks
two times.
Synchronize video and sound
If the audio and video are not
synchronized, delay the audio to match the
video.
1 Press AUDIO SYNC +/- to
synchronize the audio with the video.
• AUDIO SYNC + increases the
sound delay, and AUDIO SYNC -
decreases the sound delay.
» If the value of sound delay is set
to the maximum or minimum,
the white LED on the right base
speaker blinks two times.
Night mode
For quiet listening, night mode decreases
the volume of loud sounds when audio
is played. Night mode is only available for
Dolby Digital soundtracks.
1 Press NIGHT ON/OFF to turn night
mode on or off.
CSS5235Y_93_UM_V1.0.indb 12 4/24/2015 3:50:57 PM
13
English
EN
Play music via Bluetooth
Through Bluetooth, connect your product
with a Bluetooth device (such as an iPad,
iPhone, iPod touch, Android phone, or
laptop), and then you can listen to the
audio les stored on the device through
the speakers of this product.
What you need
• A Bluetooth device which supports
Bluetooth prole A2DP, and with
Bluetooth version as 4.1.
• The operational range between the
main unit (left and right speakers) and
a Bluetooth device is approximately 10
meters (30 feet).
1 Press Bluetooth on the remote
control to switch this product to
Bluetooth mode.
» The blue LED on the right base
speaker blinks.
2 On the Bluetooth device, switch on
Bluetooth, search for and select Philips
CSS5235Y to start connection (see
the user manual of the Bluetooth
device on how to enable Bluetooth).
» During connection, the blue LED
on the right base speaker blinks.
3 Wait until you hear a beep sound
from this product.
» The blue LED on the right base
speaker lights up.
» If the connection fails, the blue LED
on the right base speaker blinks
continually.
4 Select and play audio les or music on
your Bluetooth device.
• During play, if a call is coming,
music play is paused.
• If your Bluetooth device supports
AVRCP prole, on the remote
control you can press / to
skip to a track, or press to
pause/resume play.
5 To exit Bluetooth, select other source.
• When your switch back to
Bluetooth mode, Bluetooth
connection remains active.
Note
• The music streaming may be
interrupted by obstacles between the
device and this product, such as wall,
metallic casing that covers the device,
or other devices nearby that operate
in the same frequency.
• If you want to connect this product
with another Bluetooth device, press
and hold on the remote control
to break the current Bluetooth
connection.
Play music via NFC
NFC (Near Field Communication) is
a technology that enables short-range
wireless communication between NFC-
enabled devices, such as mobile phones.
What you need
• A Bluetooth device with NFC function.
• For pairing, tap the NFC device on the
NFC tag of this product.
• The operational range between the
main unit (left and right speakers) and
a NFC device is approximately 10
meters (30 feet).
CSS5235Y_93_UM_V1.0.indb 13 4/24/2015 3:50:57 PM
14 EN
1 Enable NFC on the Bluetooth device
(see the device' s user manual for
details).
2 Tap the NFC device on the NFC tag
of this product until you hear a beep
sound from this product.
» The blue LED on the right base
speaker lights up, and the NFC
device is connected to this product
via Bluetooth.
» If the connection fails, the blue LED
on the right base speaker blinks
continually.
3 Select and play audio les or music on
your NFC device.
• To break the connection, tap again
the NFC device with the NFC tag
on this product.
MP3 player
Connect your MP3 player to play your
audio les or music.
What you need
• An MP3 player.
• A 3.5mm stereo audio cable.
1 Using the 3.5mm stereo audio cable,
connect the MP3 player to the
AUDIO IN connector on the right
base speaker.
2 Press the buttons on the MP3 player
to select and play audio les or music.
3 Press once or two times AUX on the
remote control until higher volume is
heard.
• On the MP3 player, it is
recommended to set the volume
in the range of 80% maximum
volume.
USB storage devices
Enjoy audio on a USB storage device, such
as an MP3 player and USB ash memory,
etc.
What you need
• A USB storage device that is
formatted for FAT or NTFS le
systems, and complies with the Mass
Storage Class.
• An MP3 or WMA le on a USB
storage device
1 Connect a USB storage device to this
product.
2 Press USB on the remote control.
3 Use the remote control to control
play.
Button Action
Start, pause or resume play.
/ Skip to the previous or next track.
USB During play, press to toggle: repeat
all tracks and repeat off.
Repeat play indicator
• If repeat mode is turned on,
the white LED indicator on the
main unit blinks once.
• If repeat mode is turned off,
the white LED indicator on the
main unit blinks twice.
CSS5235Y_93_UM_V1.0.indb 14 4/24/2015 3:50:58 PM
15
English
EN
Note
• This product supports WMA les which
are converted via Windows Media
Player (WMA les converted via other
le format converters may not work).
• If a USB storage device has a large
media library, it takes some time to
load those contents.
•
This product may not be compatible with
certain types of USB storage device.
• If you use a USB extension cable, USB
HUB, or USB multi-reader, the USB
storage device may not be recognized.
• Digital camera PTP and MTP protocols
are not supported.
• Do not remove the USB storage
device while it is being read.
• DRM-protected music les (MP3,
WMA) are not supported.
• Support a USB port: 5V 1A.
Auto standby
When playing media from a connected
device, this product automatically switches
to standby after 15 minutes of button
inactivity and no audio/video play from a
connected device.
Apply factory settings
You can reset this product to the default
settings programmed at the factory.
1 In AUX mode, on the remote control
press Volume -, BASS -, and TREBLE -
in sequence within three seconds.
» When the factory settings restore is
complete, the product automatically
switches off and restarts.
5 Update software
To get the best features and support,
update your product with the latest
software.
What you need
• Connect this product to your TV
through HDMI.
Note
• Dock the surround speakers onto
the main unit (the left and right
base speakers), so that the surround
speakers can be upgraded.
Check software version
1 Switch to HDMI ARC mode (press
HDMI ARC).
2 On the remote control, press
TREBLE -, BASS - and Volume - in
sequence within three seconds.
» The current software information
is displayed on the TV screen.
Update software via USB
1 Check the latest software version on
www.philips.com/support.
• Search for your model and click on
"Software and drivers".
2 Download the software into a USB
storage device.
CSS5235Y_93_UM_V1.0.indb 15 4/24/2015 3:50:58 PM
16 EN
a Unzip the download if zipped, and
makesurethattheunzippedle
containsthefollowingtwoles.
"CSS5235.bin" (for the software of
the main unit)
"MCU5235.bin" (for the software
of the surround speakers)
b Put the "CSS5235.bin" and
"MCU5235.bin" in the root
directory of the USB device.
3 Connect the USB storage device to
the connector on this product.
4 Switch this product to the HDMI ARC
source, and switch your TV to the
HDMI source.
5 On the remote control, within 6
seconds press twice, and Volume +
once, then hold down MOVIE until
upgrade information appears on the
TV screen.
» If an upgrade media is detected, on
the TV screen you are prompted
to start the update.
» If an upgrade media is not
detected, an error message is
displayed on the TV screen. Make
sure that the latest software of this
product is put in the USB storage
device.
6 Press to start the update.
7 Wait until the update is completed.
» If the update is complete, this
product automatically turns off and
on again.
Caution
• Do not turn off the power or remove
the USB storage device when the
software update is in progress because
you might damage this player.
CSS5235Y_93_UM_V1.0.indb 16 4/24/2015 3:50:58 PM
17
English
EN
6 Product
specifications
Note
• Specications and design are subject to
change without notice.
Amplier
• Total output power:
200W RMS (+/- 0.5 dB, 10% THD)
• Frequency response:
20 Hz-20 kHz / ±3 dB
• Signal-to-noise ratio:
> 65 dB (CCIR) / (A-weighted)
• AUX Input sensitivity:
• 400mV +/- 100mV (connection
to an external device with 3.5mm
jack)
• 800mV +/- 100mV (connection
to an external device with red and
white audio jacks)
Audio
• S/PDIF Digital audio input:
• Coaxial: IEC 60958-3
• Optical: TOSLINK
Bluetooth
•Bluetooth proles: A2DP
•Bluetooth version: 4.1
Main unit (left and right base
speakers)
•Power supply:
• Model (Philips branded AC power
adapter):
DYS602-210309W; AS650-210-
AA309
• Input: 100-240 V~, 50/60 Hz 1.5 A
• Output: 21V , 3.09A
•Standby power consumption: ≤ 0.5 W
•Dimensions (W x H x D):
128 x 221 x 128 mm
•Weight
• Left base speaker: 1.11 kg
• Right base speaker: 1.29 kg
• Built-in speakers
• 2 x woofer (76.2mm/3", 8 ohm)
• 2 x tweeter (25.4mm/1", 8 ohm)
Surround speakers
• Speaker impedance: 8 ohm
• Speaker drivers: 2 x 63.5 mm (2.5") full
range
• Dimensions (W x H x D):
120 x 117 x 120 mm
• Weight: 0.66 kg/each
Subwoofer
• Power supply: 110-240 V~, 50-60 Hz
• Power consumption: 35 W
• Standby power consumption: ≤ 0.5 W
• Impedance: 3 ohm
• Speaker drivers: 1 x 133 mm (5.25")
woofer
• Dimensions (W x H x D):
226 x 251 x 306 mm
• Weight: 4.0 kg
Remote control batteries
• 1 x AAA-R03-1.5 V
CSS5235Y_93_UM_V1.0.indb 17 4/24/2015 3:50:58 PM
18 EN
Standby power management
• When the product remains inactive for
15 minutes, it automatically switches to
standby or networked standby.
• The power consumption in standby or
networked standby is less than 0.5W.
• To deactivate Bluetooth connection,
press and hold the Bluetooth button
on the remote control.
• To activate Bluetooth connection,
enable Bluetooth connection on your
Bluetooth device, or enable Bluetooth
connection via the NFC tag (if
available).
7 Troubleshooting
Warning
• Risk of electric shock. Never remove
the casing of the product.
To keep the warranty valid, never try to
repair the product yourself.
If you have problems using this product,
check the following points before you
request service. If you still have a problem,
get support at www.philips.com/support.
Main unit
The buttons on this product do not work.
• Disconnect this product from the
power supply for a few minutes, then
reconnect.
Sound
No sound from the speakers of this
product.
• Connect the audio cable from this
product to your TV or other devices.
However, you do not need a separate
audio connection when this product
and TV are connected through HDMI
ARC connection.
• Reset this product to its factory
settings.
• On the remote control, select the
correct audio input.
• Make sure that this product is not
muted.
No sound from the wireless surround
speakers.
• Wirelessly connect the speakers to the
main unit.
CSS5235Y_93_UM_V1.0.indb 18 4/24/2015 3:50:58 PM
19
English
EN
• Dock the wireless surround speakers
into the main unit to charge the
battery.
No sound from the wireless subwoofer.
• Wirelessly connect the subwoofer to
the main unit.
Distorted sound or echo.
• If you play audio from the TV through
this product, make sure that the TV is
muted.
Audio and video are not synchronized.
• Press AUDIO SYNC +/- to
synchronize the audio with the video.
Bluetooth
A device cannot connect with this
product.
• The device does not support the
compatible proles required for this
product.
• You have not enabled the Bluetooth
function of the device. See the user
manual of the device on how to
enable the function.
• The device is not correctly connected.
Connect the device correctly.
• This product is already connected with
another Bluetooth device. Disconnect
the connected device, then try again.
Quality of audio play from a connected
Bluetooth device is poor.
• The Bluetooth reception is poor. Move
the device closer to this product, or
remove any obstacle between the
device and this product.
The connected Bluetooth device
connects and disconnects constantly.
• The Bluetooth reception is poor. Move
the device closer to this product, or
remove any obstacle between the
device and this product.
• Turn off Wi-Fi function on the
Bluetooth device to avoid interference.
• For some Bluetooth, the Bluetooth
connection can be deactivated
automatically to save power. This does
not indicate any malfunction of this
product.
NFC
A device cannot connect with this
product via NFC.
• Make sure that the device is
supported by NFC.
• Make sure that NFC is enabled on the
device (see the device' s user manual
for details).
• For pairing, tap the NFC device on the
NFC tag of this product.
CSS5235Y_93_UM_V1.0.indb 19 4/24/2015 3:50:58 PM
20
For DTS patents, see http://patents.dts.com.
Manufactured under license from DTS
Licensing Limited. DTS, the Symbol, & DTS
and the Symbol together are registered
trademarks, and DTS Digital Surround is
a trademark of DTS, Inc. © DTS, Inc. All
Rights Reserved.
Manufactured under license from Dolby
Laboratories. Dolby, Pro Logic, and the
double-D symbol are trademarks of Dolby
Laboratories.
The terms HDMI and HDMI High-
Denition Multimedia Interface, and the
HDMI Logo are trademarks or registered
trademarks of HDMI Licensing LLC in the
United States and other countries.
The Bluetooth® word mark and logos are
registered trademarks owned by Bluetooth
SIG, Inc. and any use of such marks by
Gibson is under license. Other trademarks
and trade names are those of their
respective owners.
The N Mark is a trademark or registered
trademark of NFC Forum, Inc. in the
United States and in other countries.
CSS5235Y_93_UM_V1.0.indb 20 4/24/2015 3:51:00 PM
21
产品中有害物质的名称及含量
Names and Contents of Hazardous Substances
部件名称
Name of the parts
有害物质
Hazardous Substance
铅
(Pb)
汞
(Hg)
镉
(Cd)
六价铬
(Cr (VI))
多溴联苯
(PBB)
多溴二苯醚
(PBDE)
Housing
外壳 OOOOOO
Subwoofer
超重低音箱 XOOOOO
Loudspeakers
喇叭单元 OOOOOO
PWBs
电路板组件 XOOOOO
Accessories (Remote
control & cables)
附件（遥控器，
电源线，连接线）
XOOOOO
Batteries in Remote
Control (ZnC)
遥控器电池
XOOOOO
本表格依据 SJ/T 11364 的规定编制。
The table is formulated according to SJ/T 11364.
O：
表示该有害物质在该部件所有均质材料中的含量均在 GB/T 26572 规定的限量要求以下。
O： Indicates that this hazardous substance contained in all of the homogeneous materials
for this part is below the limit requirement in GB/T 26572.
×：
表示该有害物质至少在该部件的某一均质材料中的含量超出 GB/T 26572 规定的限量要求。
×： Indicates that this hazardous substance contained in at least one of the homogeneous
materials used for this part is above the limit requirement in GB/T 26572.
10
环保使用期限 Environmental Protection Use Period
此标识指期限（十年），电子电气产品中的有害物质在正常使用的条件下不会发生外泄或突变，
用户使用该电子电气产品不会对环境造成严重污染或对其人身、财产造成严重损害的期限。
This logo refers to the period (10 years) during which the hazardous substances in electronic
and electrical products will not leak or mutate so that the use of these [substances] will not
result in any severe environmental pollution, any bodily injury or damage to any assets.
CSS5235Y_93_UM_V1.0.indb 21 4/24/2015 3:51:00 PM
Specicationsaresubjecttochangewithoutnotice
2015 © Gibson Innovations Limited. All rights reserved.
This product has been manufactured by, and is sold under the responsibility of WOOX Innovations (Shanghai)
Commercial Company Ltd., and WOOX Innovations (Shanghai) Commercial Company Ltd., is the warrantor in
relation to this product.
Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under
license from Koninklijke Philips N.V.
CSS5235Y_93_UM_V1.0
CSS5235Y_93_UM_V1.0.indb 24 4/24/2015 3:51:01 PM