Philips D2301W/38 User Manual
Displayed below is the user manual for D2301W/38 by Philips which is a product in the Telephones category. This manual has pages.
Related Manuals
D230
D235
Register your product and get support at
www.philips.com/support
Short user manual
05.en en UK adaptor
Important safety
instructions
Warning
• The Electrical network is classified as hazardous. The
only way to power down the charger is to unplug
the power supply from the electrical outlet. Ensure
that the electrical outlet is always easily accessible.
• Refer to safety information before using the product.
• Hereby, Gibson Innovations declares that this
product is in compliance with the essential
requirements and other relevant provisions of
Directive 2014/53/EU.
• Use only the power supply listed in the user
instructions.
• Use only the batteries listed in the user instructions.
• Do not allow the product to come into contact
with liquids.
• Risk of explosion if battery is replaced by an
incorrect type.
• Dispose of used batteries according to the
instructions.
• When the handset rings or when the handsfree is
activated, keep the handset away from your ear to
avoid hearing damage.
1Overview
In call
Phonebook
Access the redial list.
Adjust the volume.
Recall (network dependent).
End calls.
Enter a pause (press and hold).
Turn the speaker on/off.
Mute/unmute the microphone.
In menu
Conrm / Select / Enter the option menu.
Cancel / back
Up / down
Exit menu.
Standby
Access the main menu.
Access the redial list.
Phonebook
Call log
Make and receive calls.
Switch the handset on or off (press and hold).
Make intercom call (press and hold).
Lock/unlock the keypad (press and hold).
Make and receive calls through the speaker.
D235 only: Press to play new message from
the answer machine. / Access to the answer
machine menu.
In text input
Delete text.
Enter a space.
Switch upper/lower case (press and hold).
Display icons
It shows the connection status between the
handset and base station. The more bars are
shown, the better the signal strength is.
It remains steadily on when browsing incoming
calls in the call log.
It indicates an outgoing call in the redial list.
It ashes when there is a new missed call or
when browsing new missed calls. It remains
steadily on when browsing the missed calls in call
log that are already read.
It ashes when receiving incoming call. It remains
steadily on during a call.
The speaker is on.
The ringer is off.
D235 only: Answering machine: it ashes when
there is a new message or when the memory is
full. It is displayed when the telephone answering
machine is turned on.
Voice messages indicator: ashes for new
messages, is steady for reviewed messages.
* This is network dependent.
It is displayed when you scroll up/down a list or
increase and decrease the volume.
There are more digits on the right. Press to
read.
ECO+
The ECO+ mode is activated.
D235D230
/
/
Loudspeaker
Find handset
(bottom)
Microphone
Earpiece
Loudspeaker
(back side)
Display icons
2Connect
Multi-handset version
only.
1 2 3
3Get started
Insert batteries Charge your phone
Charge 8 hours
Congure your phone
1 When using your phone for the rst time, you see
a welcome message (country dependent).
2 Set the country and language if prompted.
3 Set the date and time.
• If the time is in 12-hour format, press /
to select [am] or [pm] (country dependent).
> 70%
40% - 70%
10% - 40%
Flashing: low battery
Scrolling: charging in progress
4Enjoy
Phonebook
Add record
1 Press .
2 Select [Phonebook] > [Add new].
3 Follow on-screen instructions.
Call from the phonebook
1 Press .
2 Select a record and press .
Direct access memory
You have up to 2 direct access memories (keys 1
and 2). To dial the saved phone number automatically,
press and hold on the keys in standby mode.
Depending on your country, keys 1 and 2 are
preset to the voice mail number and information
service number of your service provider respectively
(network dependent).
Call log
Call from the call log
1 Press .
2 Select a record and press .
View record
Press > > [View].
Save record
1 Press > > [Save number].
2 Follow on-screen instructions.
Delete record
1 Press > > [Delete].
2 Follow on-screen instructions.
Redial list
Call from the redial list
1 Press .
2 Select a record and press .
Save record
1 Press > > [Save number].
2 Follow on-screen instructions.
Delete record
1 Press > > [Delete].
2 Follow on-screen instructions.
Record an announcement
(for D235 only)
1 Press > [Answ. Machine] >
[Announcement].
2 Follow on-screen instructions.
Register additional handsets
You can register additional handsets to the base
station.
1 Press and hold on the base station for
10 seconds.
2 Press .
3 Select [Services] > [Register], then press
to conrm.
4 Enter the system PIN/passcode (0000).
5 Press to conrm the PIN/passcode.
» Registration is complete in less than 2 minutes.
Restore default settings
You can reset your phone settings to the original
factory settings.
1 Press .
2 Select [Services] > [Reset], then press to
conrm.
3 Follow on-screen instructions.
Note
• You may recall the original PIN/passcode by
following this procedure.
Technical data
Battery
• Philips: 2 x AAA NiMH 1.2 V Rechargeable
500 mAh batteries
Use only the supplied batteries.
Adapter (base and charger)
Tenpao: S003GB0600050
GSP: GSCB0500S006V06E
Input: 100-240 V~ 50/60 Hz 150 mA
Output: 6 Vdc 500 mA
Phonebook with 50 entries
Call log with 20 entries
Talk time: 16 hours
Standby time: 200 hours
RF output power: <24 dBm
Frequency Band: 1880 MHz ~ 1900 MHz
Note
• You can install a DSL (digital subscriber line) lter to
prevent noise and caller ID problems caused by the
DSL interference.
• You can nd the Declaration of Conformity on
www.p4c.philips.com.
Frequently asked questions
No signal bar is displayed on the screen.
• The handset is out of range. Move it closer to the
base station.
• If the handset displays [Unregistered], register
your handset. (See the section on “Register
additional handsets”).
If I fail to pair (register) the additional handsets to
the base station, what do I do?
• Your base memory is full. Access >
[Services] > [Unregister] to unregister the
unused handsets and try again.
• If registration fails, unplug the power adapter
from the base station and plug it back. Wait for
15 seconds, and then repeat the registration
procedure.
I have chosen a wrong language which I cannot
read, what do I do?
1 Press to go back to the standby screen.
2 Press to access the main menu screen.
3 The following options will appear on the screen:
[Phone setup] > [Language]
[Réglages] > [Langue]
[Telefon-Setup] > [Sprache]
[Cong. telef.] > [Lingua]
4 Select them to access the language options.
5 Select your own language.
My handset is in searching status, what do I do?
• Make sure that the base station has power supply.
• Register the handset to the base station.
• Move the handset closer to the base station.
I cannot change the settings of my voice mail, what
do I do?
The voice mail service is managed by your service
provider but not the phone itself. Contact your
service provider to change the settings.
No display
• Make sure the batteries are charged.
• Make sure there are power and phone
connections.
The handset on the charger does not charge.
• Make sure the batteries are inserted correctly.
• Make sure the handset is placed properly on the
charger. The battery icon animates when charging.
• Make sure the docking tone setting is turned on.
When the handset is placed correctly on the
charger, you can hear a docking tone.
• The charging contacts are dirty. Disconnect the
power supply rst and clean the contacts with a
damp cloth.
• Batteries are defective. Purchase new ones with
the same specications.
Bad audio (crackles, echo, etc.)
• The handset is nearly out of range. Move it closer
to the base station.
• The phone receives interference from the nearby
electrical appliances. Move the base station away
from them.
• The phone is at a location with thick walls. Move
the base away from them.
The handset does not ring.
Make sure the handset ringtone is turned on.
The caller ID does not display.
• The service is not activated. Check with your
service provider.
• The caller’s information is withheld or unavailable.
www.philips.com/support
To access the user instructions online, use the
reference model number written on the product
label at the bottom of the base station.
This symbol on a product means that the
product is covered by European Directive
2012/19/EU.
This product has been manufactured by, and is sold
under the responsibility of Gibson Innovations Ltd.,
and Gibson Innovations Ltd. is the warrantor in
relation to this product.
Philips and the Philips Shield Emblem are registered
trademarks of Koninklijke Philips N.V. and are used
under license from Koninklijke Philips N.V.
2017 © Gibson Innovations Limited.
All rights reserved.
UMS_D230/235
05_EN_V2.0
WK17131