Philips DCB242/79 User Manual
Displayed below is the user manual for DCB242/79 by Philips which is a product in the Docking Speakers category. This manual has pages.
Related Manuals
Register your product and get support at DCB242
© 2011 Koninklijke Philips Electronics N.V.
All rights reserved.
DCB242_79_UM_V1.0
EN User manual
Important Safety Instructions
a Read these instructions.
b Keep these instructions.
c Heed all warnings.
d Follow all instructions.
e Do not use this apparatus near water.
f Clean only with dry cloth.
g Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions.
h Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that
produce heat.
i Protect the power cord from being walked on or pinched,
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
j Only use attachments/accessories specified by the
manufacturer.
k Unplug this apparatus during lightning storms or when unused
for long periods of time.
l Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate
normally, or has been dropped.
m Battery usage CAUTION – To prevent battery leakage which
may result in bodily injury, property damage, or damage to
the unit:
Install all batteries correctly, + and - as marked on the unit. •
Do not mix batteries (old and new or carbon and alkaline, •
etc.).
Remove batteries when the unit is not used for a long time.•
n Apparatus shall not be exposed to dripping or splashing.
o Do not place any sources of danger on the apparatus (e.g.
liquid filled objects, lighted candles).
p Batteries (battery pack or batteries installed) shall not be
exposed to excessive heat such as sunshine, fire or the like.
q Where the plug of the Direct Plug-in Adapter is used as the
disconnect device, the disconnect device shall remain readily
operable.
Warning
Never remove the casing of this apparatus. •
Never lubricate any part of this apparatus. •
Never place this apparatus on other electrical equipment. •
Keep this apparatus away from direct sunlight, naked flames or heat. •
Ensure that you always have easy access to the power cord, plug or •
adaptor to disconnect the apparatus from the power.
Notice
This product complies with the radio interference requirements of
the European Community.
Any changes or modifications made to this device that are not
expressly approved by Philips Consumer Lifestyle may void the user’s
authority to operate the equipment.
Recycling
Your product is designed and manufactured with high quality
materials and components, which can be recycled and reused.
When you see the crossed-out wheel bin symbol attached to a
product, it means the product is covered by the European Directive
2002/96/EC:
Never dispose of your product with other household waste. Please
inform yourself about the local rules on the separate collection of
electrical and electronic products. The correct disposal of your old
product helps prevent potentially negative consequences on the
environment and human health.
Your product contains batteries covered by the European Directive
2006/66/EC, which cannot be disposed of with normal household
waste.
Please inform yourself about the local rules on separate collection of
batteries. The correct disposal of batteries helps prevent potentially
negative consequences on the environment and human health.
Environmental information
All unnecessary packaging has been omitted. We have tried to make
the packaging easy to separate into three materials: cardboard (box),
polystyrene foam (buffer) and polyethylene (bags, protective foam
sheet.)
Your system consists of materials which can be recycled and reused
if disassembled by a specialized company. Please observe the local
regulations regarding the disposal of packaging materials, exhausted
batteries and old equipment.
2011 © Koninklijke Philips Electronics N.V. All rights reserved.
Specifications are subject to change without notice. Trademarks
are the property of Koninklijke Philips Electronics N.V. or their
respective owners. Philips reserves the right to change products at
any time without being obliged to adjust earlier supplies accordingly.
2 Your Docking Entertainment
System
Congratulations on your purchase, and welcome to Philips! To fully
benefit from the support that Philips offers, register your product at
www.philips.com/welcome.
Introduction
With this unit, you can enjoy audio from the iPod, iPhone, other audio
devices, or the FM/DAB+ radio.
The radio, iPod, or iPhone can be set as the alarm timer. You can set two
alarm timers to go off at different time.
What’s in the box
Check and identify the contents of your package:
1 x Main unit•
1 x Remote control•
1 x Power adaptor•
1 x MP3 link cable•
1 x User manual•
1 x Quick start guide•
Overview of the main unit
a
Turn on the unit or switch to standby mode.•
b REPEAT ALARM/BRIGHTNESS CONTROL
Repeat the alarm.•
Adjust the display brightness.•
c Dock for iPod/iPhone
Load an iPod/iPhone.•
d SOURCE
Select a source: iPod/iPhone, DAB+/FM tuner, or MP3 link.•
e FM antenna
Improve FM reception.•
f MP3-LINK
Jack for an external audio device.•
g DC 9V
Power supply socket.•
h OK/
Start or pause iPod/iPhone play.•
Confirm selection.•
i PRESET + /PRESET -
Select a preset radio station.•
Navigate through the iPod/iPhone menu.•
Adjust time.•
j TUNING - /TUNING +
Skip to the previous/next audio file.•
Search within an audio file.•
Tune to a radio station.•
Adjust time.•
k Display panel
Show the current status.•
l AL1/AL2
Set the alarm timer.•
Turn off the alarm tone.•
View alarm settings.•
m VOL + /VOL -
Adjust volume.•
n MENU
Select the iPod/iPhone menu.•
Select the FM/DAB+ menu.•
o SET TIME/AUTO SCAN /SLEEP
Set the clock and date.•
Scan radio stations automatically.•
Set the sleep timer.•
khno
acbd
lijm
e f g
Overview of the remote control
a POWER
Turn on the unit or switch to standby mode.•
b MENU
Select the iPod/iPhone menu.•
c SLEEP
Set the sleep timer.•
d PRESET + /PRESET -
Select a preset radio station.•
Navigate through the iPod/iPhone menu.•
Adjust time.•
e TUNING - /TUNING +
Skip to the previous/next audio file.•
Search within an audio file.•
Tune to a radio station.•
Adjust time.•
f OK/
Start or pause iPod/iPhone play.•
Confirm selection. •
g MP3 LINK
Select external audio device source.•
h iPod/iPhone
Select iPhone or iPod source.•
i INFO
Select different types of DAB+ station information.•
In FM mode, select RDS information.•
j + VOL -
Adjust volume.•
k AL 1/AL 2
Set the alarm timer.•
Turn off the alarm tone.•
View alarm settings.•
l DBB
Turn on or off dynamic bass enhancement.•
DSC
Select a preset sound setting.•
m REP AL/BRIGHTNESS
Adjust the display brightness.•
Repeat the alarm.•
n SET TIME/AUTO SCAN
Set the time and date.•
Scan radio stations automatically.•
o FM/DAB
Select the FM tuner/DAB+ source.•
3 Get started
Caution
Use of controls or adjustments or performance of procedures other •
than herein may result in hazardous radiation exposure or other
unsafe operation.
Always follow the instructions in this chapter in sequence.
If you contact Philips, you will be asked for the model and serial number
of this apparatus. The model number and serial number are on the rear
of the apparatus. Write the numbers here:
Model No. __________________________
Serial No. ___________________________
Install batteries
Note
You can only use AC power as power supply. Batteries (not supplied) •
are for backup purpose.
j
d
c
b
a
e
f
h
g
i
l
n
m
o
k
3x1.5V
LR6/UM-3/AA
1 Open the battery compartment.
2 Insert 3 x AA batteries with correct polarity (+/-) as indicated.
3 Close the battery compartment.
Prepare the remote control
Caution
Risk of explosion! Keep batteries away from heat, sunshine or fire. •
Never discard batteries in fire.
For first-time use:
1 Remove the protective tab to activate the remote control
battery.
To replace the remote control batteries:
1 Open the battery compartment.
2 Insert one lithium CR2025 battery with correct polarity (+/-) as
indicated.
3 Close the battery compartment.
Note
Before you press any function button on the remote control, first •
select the correct source with the remote control instead of the
main unit.
Connect power
Caution
Risk of product damage! Ensure that the power voltage corresponds •
to the voltage printed on the back or underside of the apparatus.
Risk of electric shock! When you unplug the AC adaptor, always pull
•
the plug from the socket. Never pull the cord.
Before connecting the AC adaptor, ensure that you have completed
•
all other connections.
Use the supplied AC power adaptor only.
•
Note
The type plate is located on the bottom of the main unit. •
1 Connect the AC power adaptor to:
the DC socket on the main unit•
the power socket. •
Set time and date
1 In standby mode, press and hold SET TIME/AUTO SCAN for 2
seconds.
»[SYNC ON] is displayed and [ON] begins to blink.
2 Press PRESET + /PRESET - to select ON or OFF.
If you select »[ON], the unit reads the DAB+ or iPod/iPhone
time and sets the clock automatically.
If you select »[OFF], the unit turns off the time synchronization.
3 Press SET TIME/AUTO SCAN to confirm.The time format
[24H] or [12H] begins to blink.
4 Press PRESET + /PRESET - to select 24H or 12H.
5 Press SET TIME/AUTO SCAN to confirm.The hour digits begin
to blink.
6 Repeat steps 4-5 to set the hour, minute, year, month, and day.
Tip
The accuracy of the transmitted time depends on the DAB+ station •
or the docked iPod/iPhone that transmits the time signal.
Turn on
1 Press POWER on the remote control.
The unit switches to the last selected source. »
DC9V 1.9A
MP3-LINK
DC9V 1.9 A
EN
1 Important
Safety
This ‘bolt of lightning’ indicates uninsulated material within your unit
may cause an electrical shock. For the safety of everyone in your
household, please do not remove product covering.
The ‘exclamation point’ calls attention to features for which you
should read the enclosed literature closely to prevent operating and
maintenance problems.
WARNING: To reduce the risk of fire or electric shock, this
apparatus should not be exposed to rain or moisture and objects
filled with liquids, such as vases, should not be placed on this
apparatus.
CAUTION: To prevent electric shock, match wide blade of plug to
wide slot, fully insert.
Switch to standby
1 Press POWER again to switch the unit to standby mode.
The time and date (if set) appear on the display panel. »
4 Play
Play from iPod/iPhone
You can enjoy audio from iPod/iPhone through this unit.
Compatible iPod/iPhone
Apple iPod and iPhone models with a 30-pin dock connector:
Made for.
iPod touch (1st, 2nd, 3rd, and 4th generation)•
iPod classic•
iPod with video •
iPod nano (1st, 2nd, 3rd, 4th, 5th, and 6th generation)•
iPod with color display•
iPod mini•
iPhone 4•
iPhone 3GS•
iPhone 3G•
iPhone •
Listen to the iPod/iPhone
1 Lift up the iPod/iPhone dock cover on the top panel.
2 Place the iPod/iPhone into the dock.
3 Press iPod/iPhone on the remote control to select iPod/iPhone
source.
The connected iPod/iPhone plays automatically. »
To pause/resume play, press • OK/.
To skip to a track, press • TUNING - /TUNING + on
the remote control.
To search during play, press and hold • TUNING - /
TUNING + , then release to resume normal play.
To go back to the previous iPod/iPhone menu, press •
MENU. To scroll through the menu, press PRESET + /
PRESET - . To confirm a selection, press OK/ .
If no key is pressed for more than 10 seconds, »OK/ acts
back as the play/pause key.
Charge the iPod/iPhone
When the unit is connected to power, the docked iPod/iPhone
begins to charge.
Tip
For certain iPod models, it may take up to a minute before the •
charging indication appears.
Play from an external device
You can also listen to an external audio device through this unit.
1 Press MP3 LINK to select the MP3 link source.
2 Connect the supplied MP3 link cable to:
the • MP3 LINK jack (3.5mm) on the back of the unit.
the headphone jack on an external device.•
3 Start to play the device (see the device user manual).
5 Listen to radio
Listen to Digital Audio Broadcasts (DAB+)
Digital Audio Broadcasting (DAB+), is a way of broadcasting radio
digitally through a network of transmitters. It provides you with more
choice, better sound quality, and more information.
1 Press FM/DAB repeatedly to select DAB+.
The unit automatically scans DAB+ radio stations. The unit »
stores all available DAB+ radio stations and then broadcasts
the first available station.
If no DAB+ service is available, »[NO SERV] is displayed.
Scan DAB+ radio stations automatically
You can perform full scan to search for DAB+ radio stations.
1 In DAB+ mode, press and hold SET TIME/AUTO SCAN for
more than 3 seconds.
The unit scans all available DAB+ radio stations and »
broadcasts the first available station.
Program DAB+ radio stations manually
1 Tune to a DAB+ radio station.
2 Press SET TIME/AUTO SCAN to activate the program mode.
3 Press TUNING - /TUNING + to select a number.
4 Press SET TIME/AUTO SCAN to confirm.
5 Repeat the above steps to program other stations.
Note
To overwrite a programmed station, store another station in its •
place.
Listen to a preset DAB+ radio station
1 In DAB+ mode, press TUNING - /TUNING + to select a
DAB+ radio station.
2 Press OK/ to confirm.
Note
If there is no DAB+ radio station available, steps mentioned above •
is invalid.
Show DAB+ information
1 During listening to DAB+ radio, press INFO repeatedly to
scroll through the following information (if available):
Dynamic Label Segment (DLS) »
Signal strength »
Program type (PTY) »
Ensemble Name »
Channel and frequency »
Signal error rate »
Bit rate and audio status »
Date »
Perform more functions through DAB+ menu
1 In DAB+ mode, press and hold MENU to enter the DAB+
menu.
2 Press TUNING - /TUNING + to select:
• [MANUAL] (tune manually)
• [SCAN] (tune automatically)
• [DRC] (dynamic range control)
• [TUNERRST] (tuner reset)
• [VERSION] (display software version)
3 If you select [DRC], press OK/ to confirm, and then press
TUNING - /TUNING + to select:
• [DRC 0]: Dynamic Range Control is switched off.
• [DRC 1/2]: Dynamic Range Control is set to half normal
level.
• [DRC 1]: Dynamic Range Control is switched on; the
default setting recommended for noisy environment.
4 Press OK/ to confirm.
To reset the tuner:
1 Follow steps 1-2 above to select [TUNERRST].
2 Press OK/ to confirm, and then press TUNING - /
TUNING + to select:
• [NO]: Cancel.
• [YES]: Reset the tuner.
3 Press OK/ to confirm.
Note
If no button is pressed within 10 seconds, the menu exits. •
Tip
Dynamic range control (DRC) adds or removes a degree of •
compensation for the differences in the dynamic range between
radio stations.
Listen to FM radio
Tune to a radio station
Tip
Position the antenna as far as possible from TV, VCR or other •
radiation source.
For optimal reception, do not place iPod/iPhone into the dock when
•
you listen to the radio.
Note
For optimal reception, fully extend and adjust the position of the •
antenna.
1 Press FM/DAB to select FM tuner.
2 Press and hold TUNING - /TUNING + for more than 2
seconds.
The radio tunes to a station with strong reception »
automatically.
3 Repeat step 2 to tune to more stations.
To tune to a weak station, press • TUNING - /TUNING
+ repeatedly until you find optimal reception.
Program radio stations automatically
You can program a maximum of 20 preset radio stations.
1 In the tuner mode, press and hold SET TIME/AUTO SCAN for
more than 2 seconds to activate automatic program mode.
The unit starts to search for radio stations. »
All available stations are programmed in the order of »
waveband reception strength.
The first programmed radio station is broadcast automatically. »
Program FM radio stations manually
You can program a maximum of 20 preset radio stations.
1 Tune to a radio station.
2 Press SET TIME/AUTO SCAN to activate the program mode.
3 Press TUNING - /TUNING + to select a number.
4 Press SET TIME/AUTO SCAN to confirm.
5 Repeat the above steps to program other stations.
Tip
To overwrite a programmed station, store another station in its •
place.
Listen to a preset radio station
1 In tuner mode, press PRESET + /PRESET - to select a
preset number.
Show RDS information
RDS (Radio Data System) is a service that allows FM stations to
show additional information. If you tune to a RDS station, the station
name is displayed.
1 Tune to a RDS station.
2 Press INFO repeatedly to scroll through the following
information (if available):
Station name »
Radio text messages »
Program type such as [NEWS] (news(, [SPORT] (sport), »
[POP M] (pop music)...
Frequency »
6 Other features
Set the alarm timer
You can set two alarms which go off at different time.
1 Ensure that you have set the clock correctly. (See “Get started -
Set time and date”.)
2 Press and hold AL1 or AL2 for 2 seconds.
The [AL1] or [AL2] icon and the hour digits begin to blink. »
3 Press TUNING - /TUNING + to set the hour.
4 Press AL1 or AL2 to confirm.
The [AL1] or [AL2] icon and the minute digits begin to blink. »
5 Repeat steps 3-4 to set the minute.
6 Repeat steps 3-4 to select whether to ring alarm the whole
week, on weekdays, or at weekend.
7 Repeat steps 3-4 to select an alarm sound source: Buzzer,
iPhone, FM, or DAB+.
8 Repeat steps 3-4 to set the alarm volume.
Turn on/off the alarm timer
Note
Ensure that you already set the alarms successfully. •
1 Press AL1/AL2 to turn on or off the alarm timer.
If the alarm timer is turned on, the alarm icon appears. »
If the alarm timer is turned off, the alarm icon disappears. »
Repeat alarm
1 When the alarm rings, press REP AL/BRIGHTNESS.
The alarm repeats ringing minutes later. »
Tip
You can press • TUNING - /TUNING + to adjust interval (5-30
minutes) to repeat alarm.
Stop alarm ring
1 When the alarm rings, press the corresponding AL1 or AL2.
The alarm stops but the alarm settings remain. »
View the alarm settings
1 Press AL1 or AL2.
Set the sleep timer
This unit can switch to standby automatically after a set period of time.
1 Press SLEEP repeatedly to select a set period of time (in
minutes).
When the sleep timer is activated, the display shows ».
To deactivate sleep timer
1 Press SLEEP repeatedly until [OFF] (off) is displayed.
When the sleep timer is deactivated, » disappears on the
display.
Adjust display brightness
1 Press REP AL/BRIGHTNESS repeatedly to select different
levels of display brightness.
7 Adjust sound
Adjust volume level
1 During play, press + VOL - to increase/decrease the volume
level.
Select a preset sound effect
1 During play, press DSC repeatedly to select:
• [POP] (pop)
• [CLASSIC] (classic)
• [JAZZ] (jazz)
• [FLAT] (flat)
• [ROCK] (rock)
Enhance bass
1 During play, press DBB to turn on or off dynamic bass
enhancement.
If DBB is activated, [DBB] is displayed. »
8 Product information
Note
Product information is subject to change without prior notice. •
Specifications
Amplifier
Rated Output Power 2 x 5 W RMS
Frequency Response 20 -20000 Hz, -3dB
Signal to Noise Ratio >67 dB
Total Harmonic Distortion <1%
Aux Input (MP3 link) 0.5 V RMS 20 kohm
Tuner (FM)
Tuning range 87.5 - 108 MHz
Tuning grid 50 KHz
Sensitivity
- Mono, 26dB S/N Ratio
- Stereo, 46dB S/N Ratio
<22 dBu
<43 dBu
Search Selectivity >28 dBf
Total Harmonic Distortion <2%
Signal to Noise Ratio >55 dB
Tuner (DAB+)
DAB+ tuning range 174.92 - 239.20 MHz
General information
AC power (Power adaptor) Input: 100-240V~, 50/60Hz, 0.7A;
Output: 9.0V 1.9A; Brand
name: Philips; Model No.: AS190-
090-BM19
Operation Power
Consumption 15 W
Standby Power Consumption <1 W
Dimensions
- Main Unit (W x H x D) 280 x 82 x 170 mm
Weight
- Main Unit 1.09 kg
9 Troubleshooting
Warning
Never remove the casing of this apparatus. •
To keep the warranty valid, never try to repair the system yourself.
If you encounter problems when using this apparatus, check the
following points before requesting service. If the problem remains
unsolved, go to the Philips web site (www.philips.com/welcome). When
you contact Philips, ensure that the apparatus is nearby and the model
number and serial number are available.
No power
Ensure that the AC power plug of the unit is connected •
properly.
Ensure that there is power at the AC outlet. •
Ensure that the batteries are inserted correctly. •
No sound
Adjust the volume. •
No response from the unit
Disconnect and reconnect the AC power plug, then turn on the •
unit again.
Poor radio reception
Increase the distance between the unit and your TV or VCR. •
Fully extend the FM antenna. •
Timer does not work
Set the clock correctly. •
Switch on the timer. •
Clock/timer setting erased
Power has been interrupted or the power plug has been •
disconnected.
Reset the clock/timer. •
Notes
Notes Notes