Philips HS199/25 User Manual
Displayed below is the user manual for HS199/25 by Philips which is a product in the Men's Shavers category. This manual has pages.
Related Manuals
with reduced physical, sensory
or mental capabilities, or lack of
experience and knowledge, unless
they have been given supervision
or instruction concerning use
of the appliance by a person
responsible for their safety.
- Keep the appliance and its cable
out of the reach of children.
Caution
- Only use the provided adapter or
the USB cable in combination with
a certied adapter*.
- Do not use the shaver, the adapter
or the USB cable if it is damaged.
- If the adapter or the USB cable is
damaged, always have it replaced
with one of the original type in
order to avoid a hazard.
- Charge, use and store the shaver
at a temperature between 5°C
and 35°C.
- Do not use the shaver in
combination with pre-shave
lotions, creams, foams, gels or other
cosmetic products.
Compliance with standards
- This Philips appliance complies
with all standards regarding
electromagnetic elds (EMF). If
handled properly and according to
the instructions in this user manual,
the appliance is safe to use based on
scientic evidence available today.
- This shaver complies with the
applicable IEC safety standards.
*HX9200, contact the Consumer Care
Centre to obtain this adapter (see
chapter ‘Ordering accessories’).
Charging
Note: Charge the appliance when the
motor stops or starts running slower.
The shaver can be charged with the
adapter or the USB cable supplied with
the appliance. You can plug the USB
cable into a certied adapter* or use
the provided adapter.
Make sure the shaver is switched off
when you start to charge it.
When you charge the shaver for the
rst time or after a long period of non-
use, let it charge continuously for 12
hours. Charging normally takes approx.
8 hours.
ENGLISH
Introduction
Congratulations on your purchase and
welcome to Philips! To fully benet
from the support that Philips offers,
register your product at
www.philips.com/welcome.
General description (Fig. 1)
1 Protection cap
2 Shaving heads
3 Shaving unit
4 Retaining frame
5 Cutter
6 Guard
7 Shaving unit release button
8 On/off slide
9 Shaver
10 Charging light
11 Socket for micro USB plug
12 Adapter (HQ80)
13 Micro USB plug
14 USB cable
15 Cleaning brush
16 Shaver storage pouch
Important
Read this user manual carefully before
you use the appliance and save it for
future reference.
Danger
- Warning: Keep the appliance, the
adapter and the USB cable dry.
- This symbol means: Forbidden to
clean under a running tap (Fig. 2).
Warning
- The adapter contains a
transformer. Do not cut off the
adapter to replace it with another
plug, as this causes a hazardous
situation.
- If you want to charge the shaver
with the adapter, only use the
provided adapter (HQ80).
- Warning: Do not use this appliance
close to a bathtub, shower or
other containers lled with water.
- Check if the voltage indicated on
the adapter corresponds to the
local mains voltage before you
connect the appliance.
- This appliance is not intended for
use by persons (including children)
For optimal performance, only charge
the shaver when the battery is low.
Do not leave the appliance connected
to the mains for more than 24 hours.
*HX9200, contact the Consumer Care
Centre to obtain this adapter (see
chapter ‘Ordering accessories’).
1 Put the micro USB plug in the
shaver (Fig. 3).
2 Put the adapter in the wall
socket (Fig. 4).
,The charging light goes on to
indicate that the appliance is
charging (Fig. 5).
Note: Charge the shaver for at least 8
hours but not more than 24 hours.
3 When the battery is fully charged,
remove the micro USB plug
from the shaver. Then remove
the adapter from the wall
socket (Fig. 6).
Note: You cannot use the shaver when
it is connected to the mains. When the
battery is empty, you have to recharge
the battery before you can use the
shaver again.
Cordless shaving time
A fully charged shaver has a cordless
shaving time of approximately 30
minutes.
Using the appliance
Note: The shaver cannot be used when it
is connected to the mains or a USB port.
Shaving
1 Remove the protection cap.
2 Press the travel lock (1) and
push the on/off slide upwards (2)
to switch on the shaver (Fig. 7).
3 Move the shaving heads quickly
over your skin. Make both straight
and circular movements (Fig. 8).
Shaving on a dry face gives the best
results.
Your skin may need 2 or 3 weeks to
get accustomed to the Philips shaving
system.
HS199, HS198
Register your product and get support at
www.philips.com/welcome
4222.002.5414.2
1
23 4
56 7
8 9 10
11 12 13
14 15 16
17 18 19
20 21 22
23 24 25
4 After use, push the on/off slide
downwards to switch off the
shaver.
5 Put the protection cap on the
shaver every time you have used
it, to prevent damage and to avoid
dirt accumulation in the shaving
heads (Fig. 9).
Cleaning and maintenance
Never use scouring pads, abrasive
cleaning agents or aggressive liquids
such as petrol or acetone to clean
the appliance.
Regular cleaning guarantees better
shaving performance.
For the best cleaning results, we advise
you to use Philips Cleaning Spray
(HQ110).
You can also clean the shaver in the
following way:
Every week: shaving unit and
hair chamber
1 Switch off the shaver.
2 Clean the top of the appliance
with the cleaning brush
supplied (Fig. 10).
3 Press the release button slightly
downwards (1) and remove the
shaving unit (2) (Fig. 11).
4 Clean the inside of the shaving
unit and the hair chamber with
the cleaning brush (Fig. 12).
5 Put the shaving unit back onto the
shaver (‘click’) (Fig. 13).
Every two months: shaving
heads
1 Switch off the shaver.
2 Press the release button slightly
downwards (1) and remove the
shaving unit (2) (Fig. 11).
3 Push the sides of the central
spring towards each other (1) and
then lift the retaining frame out of
the shaving unit (2) (Fig. 14).
4 Slide the shaving heads out of the
retaining frame.
Hold your nger underneath the
shaving head to keep the cutter and
guard together.
5 Disassemble and clean the
shaving heads one by one (Fig. 15).
Note: Do not clean more than one cutter
and guard at a time, since they are all
matching sets. If you accidentally mix
up the cutters and guards, it may take
several weeks before optimal shaving
performance is restored.
6 Clean the cutter with the short-
bristled side of the cleaning
brush (Fig. 16).
Brush carefully in the direction of the
arrow.
7 Clean the guard with the cleaning
brush (Fig. 17).
8 Slide the shaving heads back into
the retaining frame and put the
retaining frame back into the
shaving unit.
9 Put the shaving unit back onto the
shaver (‘click’) (Fig. 13).
Storage
1 Always put the protection cap
on the shaver after use, to
prevent damage and to avoid
dirt accumulation in the shaving
heads (Fig. 9).
2 Put the shaver in the storage
pouch.
Replacement
Replace the shaving heads every two
years for optimal shaving results.
Replace damaged or worn shaving heads
with HQ4 Philips shaving heads only.
1 Switch off the shaver.
2 Press the release button slightly
downwards (1) and remove the
shaving unit (2) (Fig. 11).
3 Push the sides of the central
spring towards each other (1) and
then lift the retaining frame out of
the shaving unit (2) (Fig. 18).
4 Slide the shaving heads out of the
retaining frame.
5 Slide new shaving heads into the
retaining frame (Fig. 19).
6 Put the retaining frame back into
the shaving unit.
7 Put the shaving unit back onto the
shaver (‘click’) (Fig. 13).
Ordering accessories
To purchase accessories for this
appliance, please visit our online shop
at www.shop.philips.com/service.
If the online shop is not available in
your country, go to your Philips dealer
or a Philips service centre. If you have
any difculties obtaining accessories
for your appliance, please contact the
Philips Consumer Care Centre in your
country. You nd its contact details in
the worldwide guarantee leaet.
To retain the top performance of your
shaver, make sure you clean it regularly
and replace its shaving heads at the
recommended time.
Shaving heads
- We advise you to replace your
shaving heads every two years.
Always replace with HQ4 Philips
shaving heads. (Fig. 20)
USB wall adapter
If you would like to purchase a USB
wall adapter to be able to charge the
shaver from the mains, only buy the
Philips USB wall adapter; type HX9200,
available through the Philips Consumer
Care Centre.
Cleaning
- Use Philips Cleaning Spray
(HQ110) to clean the shaving
heads thoroughly.
Environment
- Do not throw away the
appliance with the normal
household waste at the end of
its life, but hand it in at an ofcial
collection point for recycling. By
doing this, you help to preserve
the environment (Fig. 21).
- The built-in rechargeable battery
contains substances that may
pollute the environment. Remove
the battery before you discard
and hand in the appliance at an
ofcial collection point. Dispose of
the battery at an ofcial collection
point for batteries. If you have
trouble removing the battery, you
can also take the appliance to a
Philips service centre. The staff of
this centre will remove the battery
for you and will dispose of it in an
environmentally safe way (Fig. 22).
Removing the rechargeable
battery
Only remove the battery if it is
completely empty.
1 Disconnect the shaver from the
wall socket or from the USB port
and let the shaver run until it
stops.
2 Insertaat-headscrewdriver
between the plastic bottom of
the shaver and the socket for the
micro USB plug. Pry the bottom
off the shaver (Fig. 23).
3 Inserttheat-headscrewdriver
between the housing of the
shaver and the printed circuit
board. Use force to separate the
housing halves and take out the
battery holder. (Fig. 24)
4 Inserttheat-headscrewdriver
between the battery holder and
the battery. Apply some force to
break the connection strips. Take
out the battery (Fig. 25).
Do not connect the shaver to the
mains again after the rechargeable
battery has been removed.
Guarantee and service
If you need service or information
or if you have a problem, please visit
the Philips website at www.philips.
com/support or contact the Philips
Consumer Care Centre in your
country. You nd its phone number
in the worldwide guarantee leaet. If
there is no Consumer Care Centre in
your country, go to your local Philips
dealer.
Guarantee restrictions
The shaving heads (cutters and guards)
are not covered by the terms of the
international guarantee because they
are subject to wear.
Troubleshooting
This chapter summarises the most
common problems you could encounter
with the appliance. If you are unable to
solve the problem with the information
below, visit www.philips.com/support
for a list of frequently asked questions or
contact the Consumer Care Centre in
your country.
Problem Possible
cause
Solution
The
shaver
does not
shave as
well as it
used to.
The shaving
heads are
dirty. You
have not
cleaned the
shaver well
enough or
you have
not cleaned
it for a long
time.
Clean the
shaving heads
thoroughly
before you
continue
shaving. See
chapter
‘Cleaning and
maintenance’.
Long hairs
obstruct
the shaving
heads.
Clean the
cutters and
guards with
the cleaning
brush supplied.
See chapter
‘Cleaning and
maintenance’.
You mixed
up the
cutters and
guards when
you placed
them back
into the
retaining
frame after
cleaning.
Put each cutter
in the other
guard. If you
do not switch
the cutters, it
may take 2 to
3 weeks until
optimal shaving
performance is
restored.
The shaving
heads are
damaged or
worn.
Replace the
shaving heads.
See chapter
‘Replacement’.
The
shaver
does not
work
when
I push
the on/
off slide
upwards.
The re-
chargeable
battery is
empty.
Recharge
the battery.
See chapter
‘Charging’.
*HX9200，请联系客户服务中心以
获得此适配器（请参阅“订购附
件”一章）。
充电
注意： 当马达停转或转速开始下降
时，为产品充电。
该剃须刀可以通过适配器或产品
随附的 USB 线缆充电。您可以将
USB 线缆插入经认证的适配器* 或
使用随附的适配器。
请确保开始充电前，剃须刀电源已
关闭。
如果是第一次为剃须刀充电，或长
时间未使用后充电，应让其连续充电
12 小时。充电通常需要约 8 小时。
为确保最佳性能，只能在电池电量
不足时为剃须刀充电。
不要将本产品与电源接通超过 24
小时。
*HX9200，请联系客户服务中心以
获得此适配器（请参阅“订购附
件”一章）。
1 将微型 USB 插头插入剃须
刀。 (图 3)
2 将电源适配器插入电源插
座。 (图 4)
,充电指示灯亮起，表示剃须刀
正在充电。 (图 5)
注意： 至少让剃须刀充电 8 小时，
但不要超过 24 小时。
3 当电池完全充满电时，从剃须
刀上拔下微型 USB 插头。然后
从电源插座上拔下适配器。
(图 6)
注意： 连接电源时无法使用剃须
刀。电池电量耗尽后，必须先为剃
须刀充电，之后方可重新使用。
不接电源的剃须时间
完全充电的剃须刀在不连接电源的
情况下最长可使用达 30 分钟。
使用本产品
注意： 连接电源或 USB 端口时无
法使用剃须刀。
剃须
1 取下保护盖。
Problem Possible
cause
Solution
My skin is
irritated
after
shaving.
Your skin
needs time
to get
used to
the Philips
shaving
system.
Skin irritation
during the rst
2 to 3 weeks of
use is possible.
After this
period, the skin
irritation usually
disappears.
The
rotation
speed
of the
shaving
heads is
slower
than
usual.
Too much
dirt has
collected in
the shaving
heads.
Clean the
shaving heads.
See chapter
‘Cleaning and
maintenance’.
The re-
chargeable
battery is
low.
Recharge
the battery.
See chapter
‘Charging’.
简体中文
简介
感谢您的惠顾，欢迎光临飞利浦！
为了您能充分享受飞利浦提供的
支持，请在 www.philips.com/
welcome 上注册您的产品。
基本说明 (图 1)
1 保护盖
2 剃须刀头
3 剃毛刀头部件
4 固定架
5 刀片
6 网罩
7 剃须刀头部件释放按钮
8 开/关滑钮
9 剃须刀
10 充电指示灯
11 微型 USB 插头接口
12 适配器 (HQ80)
13 微型 USB 插头
14 USB 电缆
15 清洁刷
16 剃须刀存储袋
注意事项
使用本产品之前，请仔细阅读本使
用说明书，并妥善保管以备日后
参考。
危险
-警告：保持产品、适配器和
USB 线缆干燥。
-警告符号注释：禁止用在打开
的水龙头下进行清洗。 (图 2)
警告
-电源适配器内有一个变压器。切
勿自行打开更换以免发生危险。
-如果您要通过适配器为剃须刀
充电，请仅使用随附的适配器
(HQ80)。
-警告：不要在盛水的浴缸、淋
浴、洗脸盆或其他器皿附近使
用本器具。
-在将本产品连接电源前，务必
检查当地的电压是否与电源适
配器所标电压一致。
-肢体不健全、精神有障碍及缺
乏相关经验和知识的人（包括
儿童）必须在监护人的监督及
指导下使用。
-将产品及其线缆放在儿童接触
不到的地方。
注意
-请仅使用随附的适配器或 USB
线缆与经认证的适配器组合*。
-如果剃须刀、适配器或 USB 线
缆损坏，请勿再使用。
-如果适配器或 USB 线缆已损
坏，必须用原装型号进行更
换，以免发生危险。
-必须在 5 摄氏度至 35 摄氏度之
间的温度下充电、使用和存放
剃须刀。
-请勿将本剃须刀与剃须润滑
液、面霜、泡沫、凝胶或其它
护肤产品结合使用。
符合标准
-这款飞利浦产品符合关于电磁
场 (EMF) 的相关标准。据目前
的科学证明，如果正确使用并
按照本用户手册中的说明进行
操作，本产品是安全的。
-这款剃须刀符合 IEC 家电安全
标准。
注意： 不要同时清洁多组刀片和网
罩，因为它们都是相互匹配的。如
果不小心将刀片和网罩弄混，则需
要数周时间才能恢复产品的最佳剃
须性能。
6 用清洁刷的短毛一侧清洁刀
片。 (图 16)
按箭头方向仔细刷净。
7 用清洁刷清洁网罩。 (图 17)
8 滑动剃须刀头，将其重新安装
到固定架上，然后将固定架重
新安装到剃须刀头组件上。
9 将剃须刀头组件重新安装到
剃须刀上（可听到“咔哒”一
声）。 (图 13)
存储
1 使用后务必请盖上剃须刀保护
盖，以防止损坏剃须刀头并避
免其内积聚灰尘。 (图 9)
2 请将剃须刀放入存储袋。
更换
每两年更换一次刀头以获得最佳的
剃须效果。
损坏或磨损的剃须刀头只能用 HQ4
飞利浦剃须刀头更换。
1 关闭剃须刀。
2 轻轻按下释放钮 (1)，取下剃须
刀头组件 (2)。 (图 11)
3 捏拢中央弹簧的两侧 (1)，然后
向上提起固定架，将其从剃须
刀头组件中取出 (2)。 (图 18)
4 将剃须刀头滑离固定架。
5 将新的剃须刀头滑入固定架。
(图 19)
6 将固定架重新安装到剃须刀头
组件上。
7 将剃须刀头组件重新安装到
剃须刀上（可听到“咔哒”一
声）。 (图 13)
订购附件
要购买本产品的附件，请访问我们
的在线商城 www.shop.philips.com/
service。如果您的国家/地区没有
在线商城，请联系您的飞利浦经销
商或飞利浦服务中心。如果您在购
买产品的附件时遇到困难，请联系
您所在国家/地区的飞利浦客户服务
2 按旅行锁 (1)，然后向上推动
开/关滑钮 (2) 可启动剃须刀。 (
图 7)
3 将剃须刀头贴在皮肤上快速移
动。作直线和迂回动作。 (图 8)
在干爽的面部剃须效果最佳。
您的皮肤可能需要 2 到 3 周才能适
应飞利浦剃须系统。
4 使用后，向下推动开/关滑钮关
闭剃须刀电源。
5 每次使用后，盖上剃须刀保护
盖，以防止损坏剃须刀头并避
免其内积聚灰尘。 (图 9)
清洁和保养
不要使用钢丝球、研磨性清洁剂或
腐蚀性液体（例如汽油或丙酮）来
清洁产品。
为保证更好的剃须效果，剃须刀必
须定期清洗。
为了获得最佳的清洁效果，建议您
使用飞利浦清洁喷雾剂 (HQ110)。
您也可以用下列方式清洁剃须刀：
每周：剃须刀头组件和胡茬储
藏室
1 关闭剃须刀。
2 用随附的清洁刷清洁产品顶
部。 (图 10)
3 轻轻按下释放钮 (1)，取下剃须
刀头组件 (2)。 (图 11)
4 使用清洁刷清洁剃须刀头组件
内侧和胡茬储藏室。 (图 12)
5 将剃须刀头组件重新安装到
剃须刀上（可听到“咔哒”一
声）。 (图 13)
每两个月：清洁剃须刀头
1 关闭剃须刀。
2 轻轻按下释放钮 (1)，取下剃须
刀头组件 (2)。 (图 11)
3 捏拢中央弹簧的两侧 (1)，然后
向上提起固定架，将其从剃须
刀头组件中取出 (2)。 (图 14)
4 将剃须刀头滑离固定架。
用手指在剃须刀头下面托住，保持
刀片和网罩连在一起。
5 逐个拆下和清洁剃须刀头。
(图 15)
保修与服务
如果您需要服务或信息，或者有任
何疑问，请访问飞利浦网站：www.
philips.com/support。您也可与您
所在国家/地区的飞利浦客户服务中
心联系（可从全球保修卡中找到其
电话号码）。如果您所在的国家/地
区没有飞利浦客户服务中心，请与
当地的飞利浦经销商联系。
保修条款
由于剃须刀头（刀片和网罩）属于
易磨损物品，因此不在国际保修条
款的涵盖范围之列。
故障种类和处理方法
本章归纳了使用本产品时最常见的
一些问题。如果您无法根据以下信
息解决问题，请访问 www.philips.
com/support 查阅常见问题列表，
或联系您所在国家/地区的客户服
务中心。
问题 可能的
原因
解决方法
剃须
刀的
剃须
效果
没有
以前
好。
剃须刀头
变脏。您
没有将剃
须刀清洁
干净，或
长时间未
清洁过剃
须刀。
先彻底清洁
剃须刀头，
再继续剃
须。请参
阅“清洁和
维护”一
章。
过长的胡
须堵塞了
剃须刀
头。
用随附的清
洁刷清洁刀
片和网罩。
见“清洁和
保养”一
章。
您清洁后
将刀片和
网罩装回
固定架时
弄混了
刀片和网
罩。
您将刀片放
到了其他网
罩中。如果
您不调换刀
片，可能要
花 2 至 3 周
的时间才能
恢复最佳剃
须状态。
剃须刀头
已损坏或
磨损。
更换剃须刀
头。见“更
换”一章。
中心。可在全球保修卡中找到其详
细联系信息。
为了保持剃须刀的最佳性能，请确
保定期清洁并在推荐的时间更换剃
须刀头。
剃须刀头
-建议您每两年更换一次剃须刀
头。务必使用 HQ4 飞利浦剃须
刀头进行更换。 (图 20)
USB 插壁式适配器
如果您想购买 USB 插壁式适配
器，以便通过电源为剃须刀充电，
请仅购买飞利浦 USB 插壁式适配
器；类型为 HX9200，您可以通过
飞利浦客户服务中心获得。
清洁
-使用飞利浦清洁喷雾剂
(HQ110) 彻底清洁剃须刀头。
环保
-弃置产品时，请不要将其与一
般生活垃圾堆放在一起；应将
其交给官方指定的回收中心。
这样做有利于环保。 (图 21)
-内置充电电池含有可能会污染
环境的物质。弃置产品并将产
品送到官方指定的回收站之
前，应将电池取出。到官方指
定的电池回收站处理电池。如
果您在取出电池时遇到问题，
您也可以将产品送至飞利浦维
修中心。维修中心的员工会帮
您取出电池，并以环保的方式
进行处理。 (图 22)
卸下充电电池
仅在电池电量完全耗尽后方可取出
电池。
1 将剃须刀从电源插座或 USB 端
口拔出，让剃须刀运转，直至
停止为止。
2
将平头螺丝刀插入剃须刀塑料底
部和微型 USB 插头的插孔之间。
将剃须刀的底部撬开。(图 23)
3
将平头螺丝刀插入剃须刀外壳和
印刷电路板之间。用力将外壳分
为两半，取出电池舱。 (图 24)
4 将平头螺丝刀插入电池舱和电
池之间。稍微用力以断开连接
片。取出电池。 (图 25)
取出充电电池后，不要再将剃须刀
与电源连接在一起。
问题 可能的
原因
解决方法
向上
推动
开/关
滑钮
时剃
须刀
不工
作。
充电电池
的电量已
耗尽。
给电池充
电。见“充
电”一章。
我在
剃须
后出
现皮
肤过
敏。
您的皮肤
需要一定
的时间来
适应飞利
浦剃须
刀。
在前 2 至 3
周的使用过
程中，可能
会出现皮肤
过敏。在此
之后，皮肤
过敏通常会
消失。
剃须
刀头
的转
速比
平时
慢。
剃须刀头
中积聚了
太多的灰
尘。
清洁剃须刀
头。请参
阅“清洁和
保养”一
章。
充电电池
的电量不
足。
给电池充
电。见“充
电”一章。