Table of Contents
Philips HTL4110B/93 User Manual
Displayed below is the user manual for HTL4110B/93 by Philips which is a product in the Soundbar Speakers category. This manual has pages.
Related Manuals
Register your product and get support at
www.philips.com/support
Always there to help you
HTL4110B
Philips Electronics Hong Kong Ltd.
User manual
Question?
Contact
Philips
HTL4110B_93_UM_V3.0.indb 2 9/23/2014 4:57:23 PM
1
English
EN
Contents
1 Important 2
Safety 2
Care for your product 3
Care of the environment 3
Help and support 3
Trademarks 3
2 Your SoundStage 4
Main unit 4
Remote control 4
Connectors 5
3 Place your SoundStage 6
4 Connect and set up 7
Connect to TV 7
Connect audio from TV and other devices 7
5 Use your SoundStage 8
Adjust the volume 8
Choose your sound 8
MP3 player 9
Play audio through Bluetooth 9
Play music via NFC 9
USB storage devices 10
Auto standby 10
Apply factory settings 10
6 Productspecications 11
7 Troubleshooting 12
HTL4110B_93_UM_V3.0.indb 1 9/23/2014 4:57:23 PM
2EN
1 Important
Read and understand all instructions before you
use your product. If damage is caused by failure to
follow instructions, the warranty does not apply.
Read and understand all instructions before you
use your SoundStage . If damage is caused by
failure to follow instructions, the warranty does
not apply.
Safety
Riskofelectricshockorre!
• Never expose the product and accessories
to rain or water. Never place liquid
containers, such as vases, near the product.
If liquids are spilt on or into the product,
disconnect it from the power outlet
immediately. Contact Consumer Care to
have the product checked before use.
• Never place the product and accessories
nearnakedamesorotherheatsources,
including direct sunlight.
• Never insert objects into the ventilation
slots or other openings on the product.
• Where the mains plug or an appliance
coupler is used as the disconnect device,
the disconnect device shall remain readily
operable.
• Disconnect the product from the power
outlet before lightning storms.
• When you disconnect the power cord,
always pull the plug, never the cable.
Riskofshortcircuitorre!
• Before you connect the product to the
power outlet, ensure that the power
voltage matches the value printed on the
back or bottom of the product. Never
connect the product to the power outlet if
the voltage is different.
Riskofinjuryordamagetothisproduct!
• Never place the product or any objects
on power cords or on other electrical
equipment.
• If the product is transported in
temperatures below 5°C, unpack the
product and wait until its temperature
matches room temperature before
connecting it to the power outlet.
• Parts of this product can be made of
glass. Handle with care to avoid injury and
damage.
Riskofoverheating!
• Neverinstallthisproductinaconned
space. Always leave a space of at least four
inches around the product for ventilation.
Ensure curtains or other objects never
cover the ventilation slots on the product.
Riskofcontamination!
• Do not mix batteries (old and new or
carbon and alkaine, etc.).
• Danger of explosion if batteries are
incorrectly replaced. Replace only with the
same or equivalent type.
• Remove batteries if they are exhausted or
if the remote control is not to be used for
a long time.
• Batteries contain chemical substances, they
should be disposed of properly.
Riskofswallowingbatteries!
• The product/remote control may contain
a coin/button type battery, which can be
swallowed. Keep the battery out of reach
of children at all times! If swallowed, the
battery can cause serious injury or death.
Severe internal burns can occur within two
hours of ingestion.
• If you suspect that a battery has been
swallowed or placed inside any part of the
body, seek immediate medical attention.
• When you change the batteries, always
keep all new and used batteries out of
reach of children. Ensure that the battery
compartment is completely secure after
you replace the battery.
• If the battery compartment cannot be
completely secured, discontinue use of the
product. Keep out of reach of children and
contact the manufacturer.
HTL4110B_93_UM_V3.0.indb 2 9/23/2014 4:57:23 PM
3
English
EN
This is CLASS II apparatus with double
insulation, and no protective earth provided.
Care for your product
Useonlymicroberclothtocleantheproduct.
Care of the environment
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
Never dispose of your product with other
household waste. Please inform yourself about
the local rules on the separate collection of
electrical and electronic products and batteries.
The correct disposal of these products helps
prevent potentially negative consequences on
the environment and human health.
Your product contains batteries, which cannot
be disposed of with normal household waste.
Please inform yourself about the local rules on
separate collection of batteries. The correct
disposal of batteries helps prevent potentially
negative consequences on the environment and
human health.
Please visit www.recycle.philips.com for
additional information on a recycling center in
your area.
Help and support
For extensive online support, visit
www.philips.com/support to:
• download the user manual and the quick
start guide
• watch video tutorials (available only for
selected models)
• ndanswerstofrequentlyanswered
questions (FAQs)
• email us a question
• chat with our support representative.
Follow the instructions on the website to select
your language, and then enter your product
model number.
Alternatively, you can contact Consumer Care
in your country. Before you contact, note down
the model number and serial number of your
product.Youcanndthisinformationonthe
back or bottom of your product.
Use this product in the areas of an altitude of
no more than 2000 meters only.
HTL4110B_93_UM_V3.0.indb 3 9/23/2014 4:57:23 PM
4EN
2 Your
SoundStage
Congratulations on your purchase, and
welcometoPhilips!Tofullybenetfromthe
supportthatPhilipsoffers(e.g.notication
of product software upgrade), register your
product at www.philips.com/welcome.
Main unit
This section includes an overview of the main
unit.
a LED display
b
• Press to switch the SoundStage on
or off.
• Rotate to adjust the volume.
c SOURCE
Select an input source or Bluetooth mode
for the SoundStage .
d NFC tag
Tap the NFC-enabled device on the tag for
Bluetooth connection.
ba
cd
Remote control
This section includes an overview of the
remote control.
a
• Switch the SoundStage on or off.
• When EasyLink is enabled, press and
hold for at least three seconds to
switch the connected HDMI devices
to standby.
b HDMI ARC
Switch your source to HDMI ARC
connection. HDMI ARC can only be
selected if you connect your SoundStage
to an HDMI ARC compliant TV through
HDMI ARC.
n
p
l
c
e
f
h
g
b
a
ij
k
o
d
m
HTL4110B_93_UM_V3.0.indb 4 9/23/2014 4:57:23 PM
5
English
EN
c AUX/AUDIO IN
Press repeatedly to switch your audio
source to the AUX connection or MP3
connection (3.5mm jack).
d /
Skip to the previous or next track in USB
mode and Bluetooth mode (only for
AVRCP-supported Bluetooth devices).
e BASS +/-
Increase or decrease bass.
f VOLUME +/-
Increase or decrease the volume.
g
Mute or restore the volume.
h SOUND
Select a sound mode.
i DIM
Set the brightness of SoundStage display
panel.
j NIGHT MODE
Turn night mode on or off.
k SURR
Select stereo or virtual surround sound.
l TREBLE +/-
Increase or decrease treble.
m
Start, pause or resume play in USB mode
and Bluetooth mode (only for AVRCP-
supported Bluetooth devices).
n USB
Switch to USB mode.
o COAX/OPTICAL
Press repeatedly to switch your audio
source to the coaxial or optical connection.
p Bluetooth
Switch to Bluetooth mode.
Connectors
This section includes an overview of the
connectors available on your SoundStage .
Side connectors
a AUDIO IN
Audio input from an MP3 player (3.5mm
jack).
b
Audio input from a USB storage device.
Rear connectors
a COAXIAL IN
Connect to a coaxial audio output on the
TV or other devices.
b AUX IN
Connect to an audio output on the TV or
other devices.
c HDMI OUT (ARC)
Connect to the HDMI input on the TV.
d OPTICAL IN
Connect to an optical audio output on the
TV or other devices.
cd
ab
HTL4110B_93_UM_V3.0.indb 5 9/23/2014 4:57:23 PM
6EN
3 Place your
SoundStage
This SoundStage is designed to be placed
under your TV.
Caution
•The SoundStage is designed for TVs that weigh no
more than 24 kg. Do not place a CRT type TV on the
SoundStage .
•Do not place the SoundStage on an unstable cart,
stand, bracket or table. Otherwise, the SoundStage may
fall, causing serious injury to a child or adult and serious
damage to the product.
•Make sure the ventilation openings on the rear panel
are not blocked.
•Do not change the position of the SoundStage after
placing your TV on top of it.
1 PlacetheSoundStageonanyatand
stable surface near your TV. Then place
your TV on the top of the SoundStage .
2 Make sure the TV base is centered on it
and not hanging over any of its edges.
Tip
•If the TV base is too large to put on top of the
SoundStage , place the SoundStage in another location
such as on an open shelf under the TV, but keep it close
to your TV so the audio cable will reach. You can also
mount your TV on the wall above the SoundStage .
•If your TV comes with an anti-tip device, install it
according to the manufacturer's instructions and adjust
the tether after placing the TV on top the SoundStage .
•If placing the SoundStage in a cabinet or on a shelf, for
optimum audio performance, make sure the font of
the SoundStage as close as possible to the front edge
of the shelf.
•If placing the SoundStage backed up to a wall, make
sure there is at least a distance of 1 inch between the
wall and the rear of the SoundStage .
HTL4110B_93_UM_V3.0.indb 6 9/23/2014 4:57:23 PM
7
English
EN
4 Connect and set
up
This section helps you connect your
SoundStage to a TV and other devices, and
then set it up.
For information about the basic connections
of your SoundStage and accessories, see the
Quick start guide.
Note
•Foridenticationandsupplyratings,seethetypeplate
at the back or bottom of the product.
•Before you make or change any connections, make sure
that all devices are disconnected from the power outlet.
Connect to TV
Connect your SoundStage to a TV to watch
videos. You can listen to the TV audio through
your SoundStage .
Use the best quality connection available on
your SoundStage and TV.
Connect to TV through HDMI (ARC)
Best quality audio
Your SoundStage supports HDMI with Audio
Return Channel (ARC). If your TV is HDMI ARC
compliant, you can hear the TV audio through
your SoundStage by using a single HDMI cable.
TV
1 Using a High Speed HDMI cable, connect
the HDMI OUT (ARC) connector on your
SoundStage to the HDMI ARC connector
on the TV.
• The HDMI ARC connector on the TV
might be labeled differently. For details,
see the TV user manual.
2 On your TV, turn on HDMI-CEC
operations. For details, see the TV user
manual.
Note
•If your TV is not HDMI ARC compliant, connect
an audio cable to hear the TV audio through your
SoundStage .
•If your TV has a DVI connector, you can use an HDMI/
DVI adapter to connect to TV. However, some of the
features may not be available.
Connect audio from TV and
other devices
Play audio from TV or other devices through
your SoundStage speakers.
Use the best quality connection available on
your TV, SoundStage , and other devices.
Note
•When your SoundStage and TV are connected through
HDMI ARC, an audio connection is not required.0
Option 1: Connect audio through a
digital optical cable
Best quality audio
TV
HTL4110B_93_UM_V3.0.indb 7 9/23/2014 4:57:24 PM
8EN
1 Using an optical cable, connect the
OPTICAL IN connector on your
SoundStage to the OPTICAL OUT
connector on the TV or other device.
• The digital optical connector might be
labeled SPDIF or SPDIF OUT.
Option 2: Connect audio through a
digital coaxial cable
Good quality audio
1 Using a coaxial cable, connect the
COAXIAL IN connector on your
SoundStage to the COAXIAL/DIGITAL
OUT connector on the TV or other
device.
• The digital coaxial connector might be
labeled DIGITAL AUDIO OUT.
Option 3: Connect audio through
analog audio cables
Basic quality audio
1 Using an analog cable, connect the AUX
IN connector on your SoundStage to the
AUDIO OUT connectors on the TV or
other device.
VCR
5 Use your
SoundStage
This section helps you use the SoundStage to
play media from a wide range of sources.
Before you start
• Make the necessary connections described
in Quick start guide and User manual.
• Switch the TV to the correct source for
the SoundStage .
Adjust the volume
1 Rotate the power knob or press VOLUME
+/- on remote control to increase or
decrease a volume level.
• To mute sound, press .
• To restore the sound, press again or
press VOLUME +/-.
Choose your sound
This section helps you choose the ideal sound
for your video or music.
Surround sound mode
Experience an immersive audio experience with
surround sound modes.
1 Press SURR repeatedly to select surround
mode or stereo mode.
Equalizer
Change the high frequency (treble) and low
frequency (bass) settings of the SoundStage .
1 Press TREBLE +/- or BASS +/- to change
the treble or bass level.
HTL4110B_93_UM_V3.0.indb 8 9/23/2014 4:57:24 PM
9
English
EN
Night mode
For quiet listening, decrease the volume of loud
sounds when audio is played. Night mode is
only available for Dolby Digital soundtracks.
1 Press NIGHT MODE to turn night mode
on or off.
MP3 player
Connect your MP3 player to play your audio
lesormusic.
What you need
• An MP3 player.
• A 3.5mm stereo audio cable.
1 Using the 3.5mm stereo audio cable,
connect the MP3 player to the AUDIO IN
connector on your SoundStage .
2 Press AUDIO IN on the remote control.
3 Press the buttons on the MP3 player to
selectandplayaudiolesormusic.
Play audio through Bluetooth
Through Bluetooth, connect the SoundStage
with your Bluetooth device (such as an iPad,
iPhone, iPod touch, Android phone, or laptop),
andthenyoucanlistentotheaudiolesstored
on the device through your SoundStage .
What you need
• A Bluetooth device which supports
BluetoothproleA2DP,AVRCPandwith
Bluetooth version as 3.0 + EDR.
• The operational range between the
SoundStage and a Bluetooth device is
approximately 10 meters (30 feet).
1 Press Bluetooth on the remote control
to switch the SoundStage to Bluetooth
mode.
» [BT] is displayed.
2 On the Bluetooth device, switch
on Bluetooth, search for and select
PhilipsHTL4110B to start connection (see
the user manual of the Bluetooth device
on how to enable Bluetooth).
3 Wait until you hear a beep sound from the
SoundStage .
» [BT] is displayed.
» If the connection fails, [BT]isashed.
4 Selectandplayaudiolesormusicon
your Bluetooth device.
• During play, if a call is coming, music
play is paused. Play resumes when the
call ends.
• If your Bluetooth device supports
AVRCPprole,ontheremotecontrol
you can press / to skip to a track,
or press to pause/resume play.
5 To exit Bluetooth, select other source.
• When your switch back to Bluetooth
mode, Bluetooth connection remains
active.
Note
•The music streaming may be interrupted by obstacles
between the device and SoundStage , such as wall,
metallic casing that covers the device, or other devices
nearby that operate in the same frequency.
•If you want to connect your SoundStage with another
Bluetooth device, press and hold Bluetooth on the
remote control to disconnect the currently connected
Bluetooth device.
Play music via NFC
NFC (Near Field Communication) is a
technology that enables short-range wireless
communication between NFC-enabled devices,
such as mobile phones.
What you need
• A Bluetooth device with NFC function.
• For pairing, tap the NFC device on the
NFC tag of this product.
HTL4110B_93_UM_V3.0.indb 9 9/23/2014 4:57:24 PM
10 EN
• The operational range between the main
unit (left and right speakers) and a NFC
device is approximately 10 meters (30
feet).
1 Enable NFC on your Bluetooth device (see
the user manual of your device for details).
2 Tap the NFC device on the NFC tag of
this product until you hear a beep sound
from this product.
» The NFC device is connected to
this product via Bluetooth. [BT] is
displayed.
3 Selectandplayaudiolesormusicon
your NFC device.
• To break the connection, tap the
NFC device with the NFC tag on this
product again.
USB storage devices
Enjoy audio on a USB storage device, such as an
MP3playerandUSBashmemory,etc.
What you need
• A USB storage device that is formatted for
FATorNTFSlesystems,andcomplies
with the Mass Storage Class.
• A USB extension cable, if the USB storage
devicedoesnottintotheconnector.
• AnMP3orWMAleonaUSBstorage
device.
1 Connect a USB storage device to the
SoundStage .
2 Press USB on the remote control.
» [USB] is displayed.
3 Use the remote control to control play.
Button Action
Start, pause or resume play.
/ Skip to the previous or next track.
Note
•This product may not be compatible with certain types
of USB storage device.
•If you use a USB extension cable, USB HUB, or USB
multi-reader, the USB storage device may not be
recognized.
•Digital camera PTP protocols are not supported.
•Do not remove the USB storage device while it is
being read.
•DRM-protectedmusicles(MP3,WMA)arenot
supported.
•Support a USB port: 5V , 1A.
Auto standby
When playing media from a connected device,
the SoundStage automatically switches to
standby if:
• no button is pressed for 30 minutes, or
• no audio/video play from a connected
device (except USB) for 30 minutes.
Apply factory settings
You can reset this product to the default
settings programmed at the factory.
1 In standby mode, press and hold button
on the main unit for at least 5 seconds
until the product powers on.
HTL4110B_93_UM_V3.0.indb 10 9/23/2014 4:57:24 PM
11
English
EN
6 Product
specifications
Note
•Specicationsanddesignaresubjecttochangewithout
notice.
Amplier
• Total output power:
80W RMS (+/- 0.5 dB, 10% THD)
• Frequency response: 20 Hz-20 kHz / ±3 dB
• Signal-to-noise ratio:
> 65 dB (CCIR) / (A-weighted)
• Input sensitivity:
• AUX: 2 V rms
• AUDIO IN: 1 V rms
Audio
• S/PDIF Digital audio input:
• Coaxial: IEC 60958-3
• Optical: TOSLINK
USB
• Compatibility: Hi-Speed USB (2.0)
• Class support: USB Mass Storage Class
(MSC)
• File system: FAT16, FAT32, NTFS
• Maximum memory support: < 64 GB
• SupportsMP3andWMAleformats
• Sampling frequency:
• MP3: 8 kHz, 11 kHz, 12 kHz, 16 kHz,
22 kHz, 24 kHz, 32 kHz, 44.1 kHz, 48 kHz
• WMA: 44.1 kHz, 48 kHz
• Constant bit rate:
• MP3: 8 kbps-320 kbps
• WMA: 32 kbps-192 kbps
• Version:
• WMA: V7, V8, V9
Bluetooth
•Bluetoothproles:A2DP,AVRCP
•Bluetooth version: 3.0 + EDR
Main unit
•Power supply: 110-240 V~, 50/60 Hz
•Power consumption: 20 W
•Standbypowerconsumption:≤0.5W
• Speaker impedance: 4 ohm
• Speaker drivers: 2 x racetrack mid range
(1.5" x 5") + 2 x 1" tweeter + 1 x 4"
woofer
•Dimensions (WxHxD):
701 x 68 x 325 mm
•Weight: 6.3 kg
• Operating temperature and humidity:
0°C to 45°C, 5% to 90% humidity for all
climates
•Storage temperature and humidity:
-40°C to 70°C, 5% to 95%
Remote control batteries
• 1 x CR2025
HTL4110B_93_UM_V3.0.indb 11 9/23/2014 4:57:24 PM
12 EN
7 Troubleshooting
Warning
•Risk of electric shock. Never remove the casing of the
product.
To keep the warranty valid, never try to repair
the product yourself.
If you have problems using this product, check
the following points before you request service.
If you still have a problem, get support at
www.philips.com/support.
Main unit
The buttons on the SoundStage do not work.
• Disconnect the SoundStage from the
power supply for a few minutes, then
reconnect.
Sound
No sound from SoundStage speakers.
• Connect the audio cable from your
SoundStage to your TV or other devices.
However, you do not need a separate
audio connection when the SoundStage
and TV are connected through HDMI ARC
connection.
• Reset your SoundStage to its factory
settings.
• On the remote control, select the correct
audio input.
• Make sure that the SoundStage is not
muted.
Distorted sound or echo.
• If you play audio from the TV through
the SoundStage , make sure that the TV is
muted.
Bluetooth
A device cannot connect with the SoundStage
• The device does not support the
compatibleprolesrequiredforthe
SoundStage .
• You have not enabled the Bluetooth
function of the device. See the user manual
of the device on how to enable the
function.
• The device is not correctly connected.
Connect the device correctly.
• The SoundStage is already connected with
another Bluetooth device. Disconnect the
connected device, then try again.
Quality of audio play from a connected
Bluetooth device is poor.
• The Bluetooth reception is poor. Move
the device closer to the SoundStage , or
remove any obstacle between the device
and the SoundStage .
The connected Bluetooth device connects and
disconnects constantly.
• The Bluetooth reception is poor. Move
the device closer to the SoundStage , or
remove any obstacle between the device
and the SoundStage .
• Turn off Wi-Fi function on the Bluetooth
device to avoid interference.
• For some Bluetooth, the Bluetooth
connection can be deactivated
automatically to save power. This does not
indicate any malfunction of the SoundStage
.
NFC
A device cannot connect with this product via
NFC.
• Make sure that the device is supported by
NFC.
• Make sure that NFC is enabled on the
device (see the device' s user manual for
details).
• For pairing, tap the NFC device on the
NFC tag of this product.
HTL4110B_93_UM_V3.0.indb 12 9/23/2014 4:57:24 PM
12
Manufactured under license from Dolby
Laboratories. Dolby and the double-D symbol
are trademarks of Dolby Laboratories.
The Bluetooth® word mark and logos are
registered trademarks owned by Bluetooth
SIG, Inc. and any use of such marks by WOOX
Innovations is under license.
ThetermsHDMIandHDMIHigh-Denition
Multimedia Interface, and the HDMI Logo are
trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other
countries.
The N Mark is a trademark of NFC Forum, Inc.
in the United States and in other countries.
HTL4110B_93_UM_V3.0.indb 12 9/23/2014 4:57:27 PM
产品中有害物质的名称及含量
Names and Contents of Hazardous Substances
部件名称
Name of the parts
有害物质
Hazardous Substance
铅
(Pb)
汞
(Hg)
镉
(Cd)
六价铬
(Cr (VI))
多溴联苯
(PBB)
多溴二苯醚
(PBDE)
Housing
外壳 O O O O O O
Loudspeakers
喇叭单元 O O O O O O
PWBs
电路板组件 X O O O O O
Accessories (Remote
control & cables)
附件（遥控器，
电源线，连接线）
X O O O O O
Batteries in Remote
Control (ZnC)
遥控器电池
X O O O O O
本表格依据 SJ/T 11364 的规定编制。
The table is formulated according to SJ/T 11364.
O：
表示该有害物质在该部件所有均质材料中的含量均在 GB/T 26572 规定的限量要求以下。
O： Indicates that this hazardous substance contained in all of the homogeneous materials
for this part is below the limit requirement in GB/T 26572.
×：
表示该有害物质至少在该部件的某一均质材料中的含量超出 GB/T 26572 规定的限量要求。
×： Indicates that this hazardous substance contained in at least one of the homogeneous
materials used for this part is above the limit requirement in GB/T 26572.
10
环保使用期限 Environmental Protection Use Period
此标识指期限（十年），电子电气产品中的有害物质在正常使用的条件下不会发生外泄或突变，
用户使用该电子电气产品不会对环境造成严重污染或对其人身、财产造成严重损害的期限。
This logo refers to the period (10 years) during which the hazardous substances in electronic
and electrical products will not leak or mutate so that the use of these [substances] will not
result in any severe environmental pollution, any bodily injury or damage to any assets.
HTL4110B_93_UM_V3.0.indb 2 9/23/2014 4:57:23 PM
Specifications are subject to change without notice
2014 © WOOX Innovations Limited. All rights reserved.
Philips and the Philips’ Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are
used by WOOX Innovations Limited under license from Koninklijke Philips N.V.
HTL4110B_93_UM_V4.0
HTL4110B_93_UM_V3.0.indb 14 9/23/2014 4:57:27 PM