Philips MCM2150/05 User Manual
Displayed below is the user manual for MCM2150/05 by Philips which is a product in the Home Audio Systems category. This manual has pages.
Related Manuals
MCM2150
2014 © WOOX Innovations Limited. All rights reserved.
Philips and the Philips’ Shield Emblem are registered
trademarks of Koninklijke Philips N.V. and are used
by WOOX Innovations Limited under license from
Koninklijke Philips N.V.
MCM2150_05_UM_V2.0
EN User manual
1 Important
Safety
This ‘bolt of lightning’ indicates uninsulated material within the device may
cause an electrical shock. For the safety of everyone in your household,
please do not remove the covering.
The ‘exclamation mark’ calls attention to features for which you should
read the enclosed literature closely to prevent operating and maintenance
problems.
WARNING: To reduce the risk of re or electric shock, the device should
not be exposed to rain or moisture and objects lled with liquids, such as
vases, should not be placed on the device.
CAUTION: To prevent electric shock, fully insert the plug. (For regions
with polarized plugs: To prevent electric shock, match wide blade to wide
slot.)
Important Safety Instructions
• Follow all instructions.
• Heed all warnings.
• Do not use this device near water.
• Clean only with dry cloth.
• Do not block any ventilation openings. Install in accordance with
the manufacturer’s instructions.
• Do not install near any heat sources such as radiators, heat
registers, stoves, or other devices (including ampliers) that
produce heat.
• Protect the power cord from being walked on or pinched,
particularly at plugs, convenience receptacles, and the point where
they exit from the device.
• Only use attachments/accessories specied by the manufacturer.
• Use only with the cart, stand, tripod, bracket,
or table specied by the manufacturer or sold
with the device. When a cart is used, use caution
when moving the cart/device combination to
avoid injury from tip-over.
• Unplug this device during lightning storms or
when unused for long periods of time.
• Refer all servicing to qualied service personnel. Servicing is
required when the device has been damaged in any way, such as
power-supply cord or plug is damaged, liquid has been spilled or
objects have fallen into the device, the device has been exposed to
rain or moisture, does not operate normally, or has been dropped.
• Battery usage CAUTION – To prevent battery leakage which may
result in bodily injury, property damage, or damage to the unit:
• Install all batteries correctly, + and - as marked on the unit.
• Batteries (packed or installed) shall not be exposed to
excessive heat such as sunshine, re or the like.
• Remove batteries when the unit is not used for a long time.
• The device shall not be exposed to dripping or splashing.
• Do not place any sources of danger on the device (e.g. liquid lled
objects, lighted candles).
• Where the MAINS plug or an appliance coupler is used as the
disconnect device, the disconnect device shall remain readily
operable.
Warning
•Never remove the casing of this device.
•Never lubricate any part of this device.
•Never place this device on other electrical equipment.
•Keep this device away from direct sunlight, naked ames or heat.
•Never look into the laser beam inside this device.
•Ensure that you always have easy access to the power cord, plug, or adaptor to
disconnect this device from the power.
Mains fuse
This information applies only to products with a UK mains plug.
This product is tted with an approved molded plug. If you replace the
fuse, use one with:
• the ratings shown on the plug,
• a BS 1362 approval, and
• the ASTA approval mark.
Contact your dealer if you are not sure about what type of fuse to use.
Caution: To conform with the EMC directive (2004/108/EC), do not
detach the plug from the power cord.
2 Your micro system
Congratulations on your purchase, and welcome to Philips! To fully benet
from the support that Philips offers, register your product at www.philips.
com/welcome.
Introduction
With this unit, you can:
• enjoy audio from discs, USB devices, and other external devices;
• listen to radio stations.
You can enrich sound output with below sound effect:
• Digital Sound Control (DSC)
The unit supports these media formats:
What’s in the box
Check and identify the contents of your package:
SOURCE
AUDIO IN
VOLUME
CD AUDIO IN
PRESET/ALBUM
MUTE
SHUFFLE
CLOCKSLEEP
TIMER
PROG
SOUND
FM
VOL
DISPLAY
REPEAT
SOURCE
AUDIO IN
VOLUME
3 Get started
Caution
•Use of controls or adjustments or performance of procedures other than herein may
result in hazardous radiation exposure or other unsafe operation.
Always follow the instructions in this chapter in sequence.
If you contact Philips, you will be asked for the model and serial number
of this apparatus. The model number and serial number are on the back
of the apparatus. Write the numbers here:
Model No. __________________________
Serial No. ___________________________
Connect speakers
Note
•For optimal sound, use the supplied speakers only.
•Connect only speakers with impedance that is the same or higher than the supplied
speakers. Refer to the Specications section of this manual.
Connect power
Caution
•Risk of product damage! Ensure that the power supply voltage corresponds to the
voltage printed on the back or the underside of the unit.
•Risk of electric shock! When you unplug the AC power cord, always pull the plug from
the socket. Never pull the cord.
•Before you connect the AC power cord, ensure that you have completed all other
connections.
Demonstrate the features
In the standby mode, you can demonstrate features by pressing .
» The features are displayed one by one across the display
panel.
• To turn off the demonstration, press again.
Prepare the remote control
Caution
•Risk of explosion! Keep batteries away from heat, sunshine or re. Never discard
batteries in re.
•Risk of product damage! When the remote control is not used for long periods,
remove the batteries.
To insert the remote control battery:
1 Open the battery compartment.
2 Insert the supplied AAA battery with correct polarity (+/-) as
indicated.
3 Close the battery compartment.
Set clock
1 In standby mode, press and hold CLOCK on the remote control
for more than two seconds.
» [24H] or [12H] hour format is displayed.
SPEAKER OUT (8Ω)
FM
ANTENNA
100-240 V~50/60 Hz
AC MAINS~
SPEAKER OUT (8Ω)
SPEAKER OUT (8Ω)
FM
ANTENNA
100-240 V~50/60 Hz
AC MAINS~
2 Press / to select [24H] or [12H] hour format, and then
press CLOCK.
» The hour digits are displayed and begin to blink.
3 Press / to set hour, and then press CLOCK.
» The minute digits are displayed and begin to blink.
4 Repeat step 3 to set minute.
Note
•If no button is pressed in 90 seconds, the system exits clock setting mode automatically.
Tip
•You can view clock information in power on mode by pressing CLOCK.
Turn on
Press .
» The unit switches to the last selected source.
Switch to standby mode
Press again to switch the unit to standby mode.
» The clock (if set) is displayed on the panel.
Switch to ECO standby mode:
Press and hold for three seconds.
» The display panel is dimmed.
Note
•The unit switches to Eco Power Standby mode after 15 minutes in standby mode.
Switch between standby mode and ECO standby mode:
Press and hold for more than two seconds.
4 Play
Play from disc
Play from USB
Note
•Make sure that the USB device contains playable audio content.
Control play
/ Select a folder.
/ Select an audio le.
Pause or resume play.
SOURCE
AUDIO IN
VOLUME
AUDIO IN
PRESET/ALBUM
MUTE
CLOCK SLEEP
TIMER
PROG
SOUND
FM
VOLSHUFFLE
CD
REPEAT
DISPLAY
CD
SOURCE
AUDIO IN
VOLUME
AUDIO IN
PRESET/ALBUM
MUTE
CLOCK SLEEP
TIMER
PROG
SOUND
FM
VOLSHUFFLE
CD
REPEAT
DISPLAY
USB
MCM2150_05_UM_V2.0.indd 1 1/14/2014 2:17:25 PM
Stop play.
REPEAT Play a track or all tracks repeatedly.
SHUFFLE Play tracks randomly.
VOL +/- Increase or decrease the volume.
MUTE Mute or restore sound.
SOUND Enrich sound effect with DSC: balanced, clear,
powerful, warm, and bright.
DISPLAY Adjust display brightness.
Skip to a track
For CD:
Press / to select another track.
For MP3 disc and USB:
1 Press / to select an album or a folder.
2 Press / to select a track or a le.
Program tracks
You can program a maximum of 20 tracks.
1 Press PROG to activate the program mode.
2 For MP3 tracks, press / to select an album.
3 Press / to select a track, and then press PROG to
conrm.
4 Repeat steps 2 to 3 to program more tracks.
5 Press to play the programmed tracks.
» During play, [PROG] (program) is displayed.
• To erase the program, in the stop position, press .
5 Listen to the radio
Tune to a radio station
Tip
•Position the antenna as far as possible from TV, VCR or other radiation source.
•For optimal reception, fully extend and adjust the position of the antenna.
1 Press FM repeatedly to select FM source.
2 Press and hold / for more than two seconds.
» The radio tunes to a station with strong reception
automatically.
3 Repeat step 2 to tune to more stations.
To tune to a weak station:
Press / repeatedly until you nd optimal reception.
Program radio stations automatically
Note
•You can program a maximum of 20 preset radio stations (FM).
In tuner mode, press and hold PROG for three seconds to activate
automatic programming.
» All available stations are programmed in the order of
waveband reception strength.
» The rst programmed radio station is broadcast automatically.
Program radio stations manually
1 Tune to a radio station.
2 Press PROG, and then press / to select a number from
1–20.
3 Press PROG to conrm.
» The preset number and the frequency of the preset station
are displayed.
4 Repeat steps 2-3 to program more stations.
Note
•To overwrite a programmed station, store another station in its place.
Select a preset radio station
In tuner mode, press / to select a preset number.
6 Other features
Set the alarm timer
This unit can be used as an alarm clock. You can select CD, FM, or USB as
alarm source.
Note
•Make sure that you have set the clock correctly.
1 In standby mode, press and hold SLEEP/TIMER for more than two
seconds.
» The hour digits are displayed and begin to blink.
2 Press / repeatedly to set hour, and then press SLEEP/
TIMER.
» The minute digits are displayed and begin to blink.
3 Repeat step 2 to set minute, select a source (CD, FM, or USB), and
adjust volume.
Note
•If no button is pressed in 90 seconds, the system exits timer setting mode automatically.
To activate or deactivate the alarm timer:
Press SLEEP/TIMER repeatedly to activate or deactivate the alarm.
» If timer is activated, is displayed.
Tip
•If CD/USB source is selected, but no disc is placed or no USB connected, the system
switches to the tuner source automatically.
Set the sleep timer
To set the sleep timer, in turn on mode, press SLEEP/TIMER repeatedly
to select a set period of time (in minutes).
» When sleep timer is activated, is displayed. Otherwise,
disappears.
Listen to an external device
You can listen to an external device through this unit with an MP3 link
cable (not supplied).
7 Product information
Note
•Product information is subject to change without prior notice.
Specications
Amplier
Maximum Output Power 70 W
SOURCE
AUDIO IN
VOLUME
AUDIO IN
AUDIO IN
PRESET/ALBUM
MUTE
CLOCK SLEEP
TIMER
PROG
SOUND
FM
VOLSHUFFLE
CD
REPEAT
DISPLAY
AUDIO IN
Tuner (FM)
Tuning Range 87.5-108 MHz
Tuning grid 50 KHz
USB
USB Direct Version 2.0 full speed
USB 5 V Power ≤500 mA
General information
AC power 100-240 V~, 50/60 Hz
Operation Power Consumption 100 W
Eco Standby Power Consumption <0.5 W
Dimensions
- Main Unit (W x H x D)
- Speaker Box (W x H x D)
180 x 121 x 239 mm
140 x 260 x 185 mm
Weight
- Main Unit
- Speaker Box
1.6 kg
2 x 2.1 kg
USB playability information
Compatible USB devices:
• USB ash memory (USB2.0 or USB1.1)
• USB ash players (USB2.0 or USB1.1)
• memory cards (requires an additional card reader to work with
this unit)
Supported formats:
• USB or memory le format: FAT12, FAT16, FAT32 (sector size:
512 bytes)
• MP3 bit rate (data rate): 32-320 Kbps and variable bit rate
• Directory nesting up to a maximum of 8 levels
• Number of albums/ folders: maximum 99
• Number of tracks/titles: maximum 999
• File name in Unicode UTF8 (maximum length: 32 bytes)
Unsupported formats:
• Empty albums: an empty album is an album that does not contain
MP3/WMA les, and will not be shown in the display.
• Unsupported le formats are skipped. For example, word
documents (.doc) or MP3 les with extension .dlf are ignored and
not played.
• WMA, AAC, WAV, PCM audio les
• DRM protected WMA les (.wav, .m4a, .m4p, .mp4, .aac)
• WMA les in Lossless format
Supported MP3 disc formats
• ISO9660, Joliet
• Maximum title number: 128 (depending on le name length)
• Maximum album number: 99
• Supported sampling frequencies: 32 kHz, 44.1 kHz, 48 kHz
• Supported Bit-rates: 32~256 (kbps), variable bit rates
8 Troubleshooting
Warning
•Never remove the casing of this device.
To keep the warranty valid, never try to repair the system yourself.
If you encounter problems when using this device, check the following
points before requesting service. If the problem remains unsolved, go
to the Philips Web page (www.philips.com/support). When you contact
Philips, make sure that the device is nearby and the model number and
serial number are available.
No power
•Make sure that the AC cord of the apparatus is connected
properly.
•Make sure that there is power at the AC outlet.
•As a power-saving feature, the system switches off automatically
15 minutes after track play reaches the end and no control is
operated.
No sound or poor sound
•Adjust the volume.
•Check that the speakers are connected correctly.
•Check if the stripped speaker wires are clamped.
Timer does not work
•Set the clock correctly.
•Switch on the timer.
Clock/timer setting erased
•Power has been interrupted or the power cord has been
disconnected.
•Reset the clock/timer.
9 Notice
Any changes or modications made to this device that are not expressly
approved by WOOX Innovations may void the user’s authority to
operate the equipment.
This product complies with the radio interference requirements of the
European Community.
Your product is designed and manufactured with high quality materials
and components, which can be recycled and reused.
When this crossed-out wheeled bin symbol is attached to a product it
means that the product is covered by the European Directive 2002/96/
EC.
Please inform yourself about the local separate collection system for
electrical and electronic products.
Please act according to your local rules and do not dispose of your old
products with your normal household waste. Correct disposal of your
old product helps to prevent potential negative consequences for the
environment and human health.
Your product contains batteries covered by the European Directive
2006/66/EC, which cannot be disposed with normal household
waste.Please inform yourself about the local rules on separate collection
of batteries because correct disposal helps to prevent negative
consequences for the environmental and human health.
Environmental information
All unnecessary packaging has been omitted. We have tried to make
the packaging easy to separate into three materials: cardboard (box),
polystyrene foam (buffer) and polyethylene (bags, protective foam sheet.)
Your system consists of materials which can be recycled and reused
if disassembled by a specialized company. Please observe the local
regulations regarding the disposal of packaging materials, exhausted
batteries and old equipment.
The USB-IF Logos are trademarks of Universal Serial Bus Implementers
Forum, inc.
The making of unauthorized copies of copy-protected material, including
computer programs, les, broadcasts and sound recordings, may be
an infringement of copyrights and constitute a criminal offence. This
equipment should not be used for such purposes.
This apparatus includes this label:
Note
•The type plate is located on the back of the device.
MCM2150_05_UM_V2.0.indd 2 1/14/2014 2:17:27 PM