Table of Contents
Philips S6011/05 User Manual
Displayed below is the user manual for S6011/05 by Philips which is a product in the Men's Shavers category. This manual has pages.
Related Manuals
S6011
4
1
2
3
5
6
9
8
7
10
11
empty page before TOC
English
Introduction
Congratulations on your purchase and welcome to
Philips! To fully benefit from the support that
Philips offers, register your product at
www.philips.com/welcome.
General description
1 Protection cap for shaving unit
2 Click-on shaving unit
3 Shaving unit release button
4 On/off button
5 Handle
6 Socket for small plug
7 Travel lock symbol
8 Unplug for use symbol
9 Battery charge indicator with 1 light
10 Supply unit
11 Small plug
Important safety information
Read this important information carefully before
you use the appliance and its accessories and
save it for future reference. The accessories
supplied may vary for different products.
Danger
- Keep the supply unit dry.
Warning
- To charge the battery, only use the detachable
supply unit (HQ8505) provided with the
appliance.
6English
- The supply unit contains a transformer. Do not
cut off the supply unit to replace it with another
plug, as this causes a hazardous situation.
- This appliance can be used by children aged
from 8 years and above and persons with
reduced physical, sensory or mental capabilities
or lack of experience and knowledge if they
have been given supervision or instruction
concerning use of the appliance in a safe way
and understand the hazards involved. Children
shall not play with the appliance. Cleaning and
user maintenance shall not be made by
children without supervision.
- Always unplug the shaver before you clean it
under the tap.
- Always check the appliance before you use it.
Do not use the appliance if it is damaged, as
this may cause injury. Always replace a
damaged part with one of the original type.
- Do not open the appliance to replace the
rechargeable battery.
Caution
- Never immerse the cleaning system or the
charging stand in water and do not rinse it
under the tap.
- Never use water hotter than 60°C to rinse the
shaver.
- Only use this appliance for its intended purpose
as shown in the user manual.
- For hygienic reasons, the appliance should only
be used by one person.
- Never use compressed air, scouring pads,
abrasive cleaning agents or aggressive liquids
such as petrol or acetone to clean the
appliance.
7
English
- If your shaver comes with a cleaning system,
always use the original Philips cleaning fluid
(cartridge or bottle, depending on the type of
cleaning system).
- Always place the cleaning system on a stable,
level and horizontal surface to prevent leakage.
- If your cleaning system uses a cleaning
cartridge, always make sure the cartridge
compartment is closed before you use the
cleaning system to clean or charge the shaver.
- When the cleaning system is ready for use, do
not move it to prevent leakage of cleaning fluid.
- Water may drip from the socket at the bottom
of the shaver when you rinse it. This is normal
and not dangerous because all electronics are
enclosed in a sealed power unit inside the
shaver.
- Do not use the supply unit in or near wall
sockets that contain an electric air freshener to
prevent irreparable damage to the supply unit.
Electromagnetic fields (EMF)
- This Philips appliance complies with all
applicable standards and regulations regarding
exposure to electromagnetic fields.
General
- This shaver is waterproof. It is suitable for use in
the bath or shower and for cleaning under the
tap. For safety reasons, the shaver can
therefore only be used without cord.
- The supply unit is suitable for mains voltages
ranging from 100 to 240 volts.
- The supply unit transforms 100-240 volts to a
safe low voltage of less than 24 volts.
8English
The display
Charging
Note: If you press the on/off button during
charging, the 'unplug for use' symbol flashes white
to remind you that you have to disconnect the
appliance from the wall socket.
Battery charge indicator with 1 light
Quick charge: When the battery is empty and you
connect the appliance to the wall socket, the
battery charge indicator flashes quickly. When the
appliance contains enough energy for one shave,
the battery charge indicator starts flashing slowly.
While the appliance continues to charge, the
battery charge indicator flashes slowly until the
appliance is fully charged.
Battery fully charged
Note: When the battery is full, the display switches
off automatically after 30 minutes.
Note: This appliance can only be used without
cord.
Battery charge indicator with 1 light
When the battery is fully charged, the battery
charge indicator lights up white continuously.
Battery low
Battery charge indicator with 1 light
9
English
When the battery is almost empty, the battery
charge indicator flashes orange.
’Unplug for use’ reminder
The appliance is equipped with an ‘unplug for use’
reminder. The ‘unplug for use’ symbol flashes to
remind you that you have to disconnect the
appliance from the supply unit before you can
switch it on.
Travel lock
You can lock the appliance when you are going to
travel. The travel lock prevents the appliance from
being switched on by accident.
Activating the travel lock
3 sec.
1Press the on/off button for 3 seconds to enter
the travel lock mode.
While you activate the travel lock, the travel
lock symbol lights up continuously. When the
travel lock is activated, the travel lock symbol
flashes.
Deactivating the travel lock
1Press the on/off button for 3 seconds.
10 English
The travel lock symbol flashes and then lights
up continuously. The appliance is now ready for
use again.
Charging
Charge the shaver before you use it for the first
time and when the display indicates that the
battery is almost empty.
Charging takes approx. 8 hours. When the
appliance is fully charged, it has an operating time
of 40 minutes.
Note:You cannot use the appliance while it is
charging.
Charging with the supply unit
1Make sure the appliance is switched off.
2Put the small plug in the appliance and put the
supply unit in the wall socket.
3After charging, remove the supply unit from the
wall socket and pull the small plug out of the
appliance.
Using the appliance
Note: This appliance can only be used without
cord.
11
English
Switching the appliance on and off
1To switch on the appliance, press the on/off
button once.
2To switch off the appliance, press the on/off
button once.
Shaving
Skin adaptation period
Your first shaves may not bring you the result you
expect and your skin may even become slightly
irritated. This is normal. Your skin and beard need
time to adapt to any new shaving system. To allow
your skin to adapt to this new appliance, we advise
you to shave regularly (at least 3 times a week)
and exclusively with this appliance for a period of
3 weeks.
Dry shaving
1Switch on the appliance.
2Move the shaving heads over your skin in
circular movements to catch all hairs growing in
different directions. Exert gentle pressure for a
close, comfortable shave.
Note: Do not press too hard, this can cause skin
irritation.
3Clean the appliance after use.
Wet shaving
For a more comfortable shave, you can also use
this appliance on a wet face with shaving foam or
shaving gel.
To shave with shaving foam or shaving gel, follow
the steps below:
12 English
1Apply some water to your skin.
2Apply shaving foam or shaving gel to your skin.
3Rinse the shaving unit under the tap to ensure
that the shaving unit glides smoothly over your
skin.
4Switch on the appliance.
5Move the shaving heads over your skin in
circular movements to catch all hairs growing in
different directions. Exert gentle pressure for a
close, comfortable shave.
Note: Do not press too hard, this can cause skin
irritation.
Note: Rinse the shaving unit regularly to ensure
that it continues to glide smoothly over your
skin.
6Dry your face.
7Clean the appliance after use.
Note: Make sure you rinse all foam or shaving
gel off the appliance.
Using the click-on attachments
Note: The accessories supplied may vary for
different products. The box shows the accessories
that have been supplied with your product.
13
English
Removing or attaching the click-on
attachments
1Make sure the appliance is switched off.
2Pull the attachment straight off the appliance.
Note: Do not twist the attachment while you
pull it off the appliance.
3Insert the lug of the attachment into the slot in
the top of the appliance. Then press down the
attachment to attach it to the appliance (‘click’).
Cleaning and maintenance
Note: The accessories supplied may vary for
different products. The box shows the accessories
that have been supplied with your product.
Cleaning the shaver under the tap
Clean the shaver after every shave for optimal
performance.
Be careful with hot water. Always check if the
water is not too hot, to prevent burning your
hands.
Never dry the shaving unit with a towel or tissue,
as this may damage the shaving heads.
1Switch on the appliance.
2Rinse the shaving unit under a warm tap.
14 English
3Switch off the appliance. Press the release
button to open the shaving unit.
4Rinse the hair chamber under the tap.
5Rinse the shaving head holder under a warm
tap.
6Carefully shake off excess water and let the
shaving head holder air dry.
7Close the shaving head holder ('click').
Cleaning the click-on attachments
The accessories supplied may vary for different
products. The box shows the accessories that have
been supplied with your product.
Storage
We advise you to let the appliance and its
attachments dry before you put the protection
caps on the attachments or store the shaver in the
pouch.
15
English
Note: The accessories supplied may vary for
different products. The box shows the accessories
that have been supplied with your product.
Put the protection cap on the shaver to protect it
from any dirt accumulation.
Replacement
Replacing the shaving heads
2yrs
For maximum shaving performance, we advise you
to replace the shaving heads every two years.
Replace damaged shaving heads immediately.
Always replace the shaving heads with original
Philips shaving heads (see 'Ordering accessories').
1Switch off the appliance.
2Press the release button to open the shaving
unit.
3Pull the shaving head holder off the bottom
part of the shaving unit.
16 English
1
2
4Turn the retaining rings anticlockwise and
remove them. Place them aside in a safe place.
5Remove the shaving heads from the shaving
head holder.
Discard the used shaving heads immediately to
avoid mixing them with the new shaving heads.
6Place the new shaving heads in the shaving
head holder.
Note: Make sure that the projections of the
shaving heads fit exactly into the recesses of
the shaving head holder.
1
2
7Place the retaining rings back onto the shaving
heads and turn them clockwise to reattach the
retaining ring.
Each retaining ring has two recesses and two
projections that fit exactly in the projections
and recesses of the shaving head holder.
17
English
- Turn the ring clockwise until your hear a click to
indicate that the ring is fixed.
Note: Hold the shaving head holder in your
hand when you reinsert the shaving heads and
reattach the retaining rings. Do not place the
shaving head holder on a surface, as this may
cause damage to the shaving heads.
8Reinsert the hinge of the shaving head holder
into the slot of the shaving unit. Close the
shaving head holder (‘click’).
Ordering accessories
To buy accessories or spare parts, visit
www.shop.philips.com/service or go to your
Philips dealer. You can also contact the Philips
Consumer Care Center in your country (see the
international warranty leaflet for contact details).
Recycling
- Do not throw away the product with the normal
household waste at the end of its life, but hand
it in at an official collection point for recycling.
By doing this, you help to preserve the
environment.
18 English
- This product contains a built-in rechargeable
battery which shall not be disposed of with
normal household waste. We strongly advise
you to take your product to an official collection
point or a Philips service centre to have a
professional remove the rechargeable battery.
- Follow your country’s rules for the separate
collection of electrical and electronic products
and rechargeable batteries. Correct disposal
helps prevent negative consequences for the
environment and human health.
Removing the rechargeable appliance battery
Only remove the rechargeable battery
when you discard the appliance. Before you
remove the battery, make sure that the
appliance is disconnected from the mains
and that the battery is completely empty.
Take any necessary safety precautions
when you handle tools to open the
appliance.
Be careful, the battery strips are sharp.
1Remove the screw in the back panel with a
screwdriver. Then remove the back panel.
2Bend the hooks aside and remove the power
unit.
19
English
3Break the snap hooks and remove the front
panel of the power unit.
4Take out the battery holder and cut the battery
tags with a pair of cutting pliers.
Warranty and support
If you need information or support, please visit
www.philips.com/support or read the
international warranty leaflet.
Warranty restrictions
The shaving heads (cutters and guards) are not
covered by the terms of the international warranty
because they are subject to wear.
Troubleshooting
This chapter summarizes the most common
problems you could encounter with the appliance.
If you are unable to solve the problem with the
information below, visit www.philips.com/support
for a list of frequently asked questions or contact
the Consumer Care Center in your country.
20 English
Shaver
Problem Possible cause Solution
The appliance
does not work
when I press the
on/off button.
The appliance is still
attached to the wall
socket. For safety
reasons, the
appliance can only
be used without
cord.
Unplug the appliance and
press the on/off button to
switch on the appliance.
The rechargeable
battery is empty.
Recharge the battery (see
'Charging').
The travel lock is
activated.
Press the on/off button for
3 seconds to deactivate the
travel lock.
The shaving unit is
soiled or damaged
to such an extent
that the motor
cannot run.
Clean the shaving heads
thoroughly or replace
them. Also see 'Hairs or dirt
obstruct the shaving heads'
for a detailed description of
how to clean the shaving
heads thoroughly.
The appli
ance does not
shave as well as
it used to.
The shaving heads
are damaged or
worn.
Replace the shaving heads
(see 'Replacement').
Hairs or dirt obstruct
the shaving heads.
Clean the shaving heads in
the regular way or clean
them thoroughly.
21
English
Problem Possible cause Solution
To clean the shaving heads
thoroughly, remove the
shaving heads from the
shaving head holder one
by one (see
'Replacement'). Then
separate the cutter from its
guard and rinse each
matching set under the tap.
After rinsing, place the
cutter back into its
corresponding guard.
Finally, put the shaving
heads back into the
shaving head holder (see
'Replacement').
Water is leaking
from the bottom
of the appliance.
During cleaning,
water may collect
between the inner
body and the outer
shell of the
appliance.
This is normal and not
dangerous because all
electronics are enclosed in
a sealed power unit inside
the appliance.
22 English
简体中文
简介
感谢您的惠顾，欢迎光临飞利浦！ 为了让您能充分享
受飞利浦提供的支持，请在 www.philips.com/welcome
上注册您的产品。
基本说明
1 剃须刀头部件保护盖
2 卡入式剃须刀头部件
3 剃须刀头部件释放按钮
4 开/关按钮
5 手柄
6 小插头插座
7 旅行锁符号
8 “拔出插头即可使用”符号
9 电池充电指示灯（1 级指示）
10 电源部件
11 小插头
重要安全信息
使用本产品及其附件之前，请仔细阅读本重要信息，并
妥善保管以供日后参考。 随附的附件可能因产品而
异。
危险
- 保持电源部件干燥。
- 警告符号注释： 禁止在打开的水龙头下进行清洗。
警告
- 要给电池充电，请仅使用产品随附的可拆卸电源部
件 (HQ8505)。
- 电源部件中包含一个变压器。 请勿自行更换电源部
件的插头，否则将导致严重后果。
23
简体中文
- 本产品也可以由 8 岁或以上年龄的儿童以及肢体不
健全、感觉或精神上有障碍或缺乏相关经验和知识
的人士使用，但前提是有人对他们使用本产品进行
监督或指导，以确保他们安全使用，并且让他们明
白相关的危害。 切勿让儿童玩弄本产品。 不要让儿
童在无人监督的情况下对本产品进行清洁和保养。
- 将剃须刀手持部分与电源软线分开后，才能在水龙
头下清洗手持部分。
- 使用前，请务必检查产品。 请勿使用损坏的产品，
否则可能对人体造成伤害。 请务必用原装型号更换
损坏的部件。
- 切勿拆开本产品更换充电电池。
警告
- 切勿将清洁系统或充电座浸入水中，也不要在水龙
头下冲洗。
- 警告符号注释： 禁止在打开的水龙头下进行清洗
- 切勿使用温度高于 60°C 的热水冲洗剃须刀。
- 只能将本产品用于用户手册中所示的原定用途。
- 出于卫生的目的，本产品只能供一个人使用。
- 切勿使用压缩气体、钢丝绒、研磨性清洁剂或腐蚀
性液体（例如汽油或丙酮）来清洁产品。
- 如果剃须刀随附清洁系统，应始终使用原装飞利浦
清洁液（滤芯或瓶，取决于清洁系统类型）。
- 清洁系统必须放在稳定、平坦的水平表面上，以防
漏液。
- 如果清洁系统采用清洁滤芯，在使用清洁系统进行
清洁或为剃须刀充电之前，应始终确保滤芯仓已关
闭。
- 清洁系统准备就绪时，切勿移动，以免清洁液漏
出。
- 冲洗剃须刀时，水可能从产品底部的插口漏出。 这
是正常的，而且没有危险，因为所有电子元件都封
闭在剃须刀内部的密封电源部件中。
- 请勿在包含电动空气清新器的墙壁插座上或其周围
使用电源部件，以免电源部件受到不可修复的损
坏。
24 简体中文
电磁场 (EMF)
- 本 Philips 产品符合所有有关暴露于电磁场的适用标
准和法规。
概述
- 符号注释：适合于在洗澡或淋浴时使用。 允许在盛
水的浴缸、淋浴、洗脸盆或其他器皿附近使用本器
具。
- 该剃须刀具有防水性能。 适合在沐浴或淋浴时使
用，也可以放在水龙头下清洗。 出于安全原因，该
剃须刀在使用时不能连接电线。
- 电源部件适合在 100 - 240 伏的电源电压下工作。
- 该电源部件可将 100-240 伏的电压转换为 24 伏以
下的安全低电压。
显示屏
充电
注意： 充电期间按开/关按钮，“拔出插头即可使
用”符号会呈白色闪烁，提醒您需断开产品与电源插座
的连接。
电池充电指示灯（1 级指示）
快速充电： 电池电量耗尽后，当您将产品连接到电源
插座时，电池充电指示灯会快速闪烁。 产品包含的电
量足够完成一次剃须时，电池充电指示灯开始缓慢闪
烁。
如果产品继续充电，电池充电指示灯会缓慢闪烁，直至
产品充满电。
电池已完全充满
注意： 电池充满电后，显示屏会在 30 分钟后自动关
闭。
注意： 本产品只能在不接电源的情况下使用。
25
简体中文
电池充电指示灯（1 级指示）
电池充满电后，电池充电指示灯将呈白色持续亮起。
电池电量不足
电池充电指示灯（1 级指示）
当电池的电量几乎耗尽时，电池充电指示灯会呈橙色闪
烁。
“拔出插头即可使用”提醒
产品配有“拔出插头即可使用”提醒。 “拔出插头即
可使用”符号闪烁，提醒您需先断开产品与电源部件的
连接才能启动产品。
旅行锁
您可以在携带本产品旅行之前将其锁住。 旅行锁可防
止本产品被意外启动。
启用旅行锁
3 sec.
1 按住开/关按钮 3 秒钟以进入旅行锁模式。
26 简体中文
启用旅行锁后，旅行锁符号会持续亮起。 旅行锁启
用后，旅行锁符号将闪烁。
解除旅行锁
1 按开/关按钮 3 秒钟。
旅行锁符号闪烁，然后持续亮起。 现在可以再次使
用本产品。
充电
首次使用剃须刀之前，或当显示屏指示电池电量几乎耗
尽时，请先为剃须刀充电。
充电约需 8 小时。 产品充满电后，可持续工作 40 分
钟。
注意：不能在充电时使用本产品。
用电源部件充电
1 确保产品电源已关闭。
2 将小插头插入本产品，然后将电源部件插入电源插
座。
3 充电之后，从电源插座上拔下电源部件，并从产品
上拔下小插头。
使用本产品
注意： 本产品只能在不接电源的情况下使用。
27
简体中文
打开或关闭产品
1 要打开本产品，请按一下开/关按钮。
2 要关闭产品，请按一下开/关按钮。
剃须
皮肤适应期
前几次剃须可能不会带给您预期效果，并且您的皮肤可
能会受到轻度刺激。 这是正常的。 您的皮肤和胡须需
要时间适应任何新的剃须系统。 为了让您的皮肤适应
这款新产品，我们建议您在 3 周时间内定期（至少每
周 3 次）仅使用本产品剃须。
干用剃须
1 启动产品。
2 让剃须刀头在您的皮肤上作迂回运动，以刮剃向不
同方向生长的所有须发。 轻轻按压，以获取舒适贴
面的剃须感受。
注意： 划圈动作比直线动作的剃须效果更好。
3 使用后要清洁本产品。
湿剃
要获得更舒适的剃须体验，您也可以先用剃须泡沫或剃
须啫喱将脸弄湿，然后再用本产品进行剃须。
要用剃须泡沫或剃须啫喱剃须，请按照下面的步骤执行
操作：
1 用水润湿皮肤。
28 简体中文
2 在皮肤上涂抹剃须泡沫或剃须啫喱。
3 在水龙头下冲洗一下剃须刀头部件，确保剃须刀头
部件可以在您的皮肤上顺畅滑动。
4 启动产品。
5 让剃须刀头在您的皮肤上作迂回运动，以刮剃向不
同方向生长的所有须发。 轻轻按压，以获取舒适贴
面的剃须感受。
注意： 不要用力按压剃须刀，这样做可能会导致皮
肤疼痛。
注意： 定期冲洗剃须刀头部件，确保其能够继续在
您的皮肤上顺畅滑动。
6 擦干面部。
7 使用后要清洁本产品。
注意： 确保冲洗干净本产品上的所有泡沫或剃须啫
喱。
使用卡入式附件
注意： 随附的附件可能因产品而异。 包装盒上会显示
随附于您产品的附件。
拆卸或安装卡入式附件
1 确保产品电源已关闭。
2 将附件竖直抽离产品。
注意： 将附件从产品上抽出时，不要旋转。
29
简体中文
3 将附件的凸缘插入本产品顶部的槽内。 然后，按下
附件将其安装到本产品上（可听到“咔哒”一声）
。
清洁和保养
注意： 随附的附件可能因产品而异。 包装盒上会显示
随附于您产品的附件。
在水龙头下冲洗剃须刀
每次剃须后请清洁剃须刀，以获得出色性能。
使用热水要当心。 切记先检查水温是否太高，以防烫
手。
不要用毛巾或纸巾擦拭剃须刀头部件，因为这样可能会
损坏剃须刀头。
1 启动产品。
2 用温水冲洗剃须刀头部件。
3 关闭产品。 按下释放按钮，打开剃须刀头部件。
30 简体中文
4 在水龙头下冲洗胡茬储藏室。
5 用温水冲洗剃须刀头支架。
6 小心甩干多余的水，然后让剃须刀头支架晾干。
7 合上剃须刀头支架（可听到“咔哒”一声）。
清洁卡入式附件
随附的附件可能因产品而异。 包装盒上会显示随附于
您产品的附件。
存放
建议您将产品及其配件晾干后再将保护盖放在配件上，
或将剃须刀存放在收纳袋中。
注意： 随附的附件可能因产品而异。 包装盒上会显示
随附于您产品的附件。
将保护盖盖在剃须刀上，以防积聚灰尘。
31
简体中文
更换
更换剃须刀头
2yrs
为获得最佳剃须效果，建议每两年更换一次剃须刀头。
立即更换损坏的剃须刀头。 务必使用原装飞利浦剃须
刀头 (请参见 '订购配件')进行更换。
1 关闭产品。
2 按下释放按钮，打开剃须刀头部件。
3 将剃须刀头支架从剃须刀头部件的底部抽离。
1
2
4 逆时针旋转固定环并将其取下。将其存放在安全的
地方。
5 从剃须刀头支架上卸下剃须刀头。
立即丢弃用过的剃须刀头，以免与新的剃须刀头混
淆。
32 简体中文
6 将新的剃须刀头装到剃须刀头支架中。
注意： 确保剃须刀头的凸缘正好装入剃须刀头支架
的凹槽。
1
2
7 将固定环放回剃须刀头上，然后顺时针旋转以重新
安装固定环。
各固定环均具有两个凹槽和两个凸缘，正好装入剃
须刀头支架的凸缘和凹槽内。
- 顺时针旋转固定环，直至听到“咔哒”一声，表明
固定环已就位。
注意： 当您重新插入剃须刀头并重新安装固定环
时，请将剃须刀头支架握在手中。 切勿将剃须刀头
支架放在平面上，否则可能会损坏剃须刀头。
33
简体中文
8 将剃须刀头支架的铰链重新卡入剃须刀头部件的槽
内。 合上剃须刀头支架（可听到“咔哒”一声）。
订购配件
要购买附件或备件，请访问
www.shop.philips.com/service 或联系您的飞利浦经销
商。 您还可以联系所在国家/地区的飞利浦客户服务中
心（请参阅全球保修卡了解详细联系信息）。
回收
- 弃置本产品时，请不要将其与一般生活垃圾放在一
起，应将其交给政府指定的回收中心。 这样做将有
利于环保。
- 此产品包含内置充电电池；请勿将充电电池与一般
生活垃圾一起弃置。 强烈建议您将自己的产品送到
官方收集点或飞利浦服务中心，让专业人士移除充
电电池。
- 遵循您的国家/地区有关分类回收电子电气产品和充
电电池的规定。 正确弃置产品有助于避免对环境和
人类健康造成不良后果。
мȞġĈҴˀΙĀǩ؆Ӎߒʔˌɫǩ؆ĈҴˀΙ(Pb)᰽(Hg)⬡(Cd)ԣᲱ(Cr (VI) )Ġ⅑ԓ᧠(PBB) Ġ⅑ȕ᧠⓭(PBDE)PCB’s
מŪǗɢذX O O O O O
Electrical
contact pins
ǗˈǦX O O O O O
Power plug
Ǘ۷ǼX O O O O O
ǕȪϜ֪֙SJ/T 11364Āܪǭৠ뺯OȪФ˽ĈҴˀΙć˽ˌɫǨĈߴΙࠒնġĀߒʔߴćGB/T 26572ܪǭĀՄʔđŘĪ뺯
XȪФ˽ĈҴˀΙψɺć˽ˌɫĀԚĂߴΙࠒնġĀߒʔɸŜGB/T 26572ܪǭĀՄʔđ뺯
- 该表格中所显示的“有害物质”在产品正常使用情
况下不会对人身和环境产生任何伤害。
34 简体中文
- 该表格中所显示的“有害物质”及其存在的部件向
消费者和回收处理从业者提供相关物质的存在信
息，有助于产品废弃时的妥善处理。
取出可充电的产品电池
仅在丢弃本产品时方可取出充电电池。 卸下电池
之前，请确保本产品与电源断开连接并且电池电
量已耗尽。
当您使用工具打开本产品时，请采取必要的安全
保护措施。
注意，电池带非常锋利。
1 使用螺丝刀取出后面板中的螺钉。 拆除后面板。
2 将钩子向外掰，取出电源部件。
3 脱开安全钩，取下电源部件的前面板。
35
简体中文
4 取出电池舱，用一把钢丝钳剪下电池标签。
保修和支持
如需信息或支持，请访问 www.philips.com/support 或
阅读国际保修卡。
保修条款
由于剃须刀头（刀片和网罩）属于易磨损物品，因此不
在国际保修条款的涵盖范围之列。
故障种类和处理方法
本章归纳了使用本产品时最常见的一些问题。如果您无
法根据以下信息解决问题，请访问
www.philips.com/support 查阅常见问题列表，或联系
您所在国家/地区的客户服务中心。
剃须刀
问题 可能的原因 解决方法
按下开/关钮时，
产品不工作。 本产品仍然连接着电
源插座。 出于安全原
因，本产品在使用时
不能连接电线。
拔掉本产品插头并按开/关按
钮打开产品。
充电电池的电量已耗
尽。 给电池充电 (请参见 '充电')。
旅行锁已被激活。 按住开/关按钮 3 秒钟以解除
旅行锁。
剃须刀头部件被污染
或损坏，导致马达无
法运行。
彻底清洁剃须刀头或将其更
换。 有关如何彻底清洗剃须
刀头的详细说明，另请参
阅“毛发或污垢堵塞了剃须刀
头”。
36 简体中文
问题 可能的原因 解决方法
产品的剃须效果
没有以前好。 剃须刀头已损坏或磨
损。 更换剃须刀头 (请参见 '更换
')。
毛发或污垢堵塞了剃
须刀头。 对剃须刀头进行常规或彻底清
洁。
要彻底清洁剃须刀头，请将剃
须刀头从剃须刀头支架上逐一
(请参见 '更换')卸下。 然后，
分离刀片和网罩，并在水龙头
下冲洗每个刀片和网罩套装。
冲洗后，将刀片放回对应的网
罩中。 最后，将剃须刀头装
回到剃须刀头支架 (请参见
'更换')中。
水从本产品底部漏
出。 在清洁过程中，水可
能聚集在本产品的机
身内部与外壳之间。
这是正常现象，而且没有危
险，因为所有电子元件都封闭
在本产品内部的密封电源部件
中。
珠海经济特区飞利浦家庭电器有限公司 中国珠海市三灶镇琴石工业区 全国顾客服务热线: 4008 800 008本产品根据国标 GB4706.1-2005,GB4706.9-2008制造产品： 飞利浦电动剃须刀 型号： S6011 额定电压： 220V～额定频率： 50Hz额定输入功率：9 W产地： 中国广东珠海生产日期： 请见产品本体
保留备用
发行日期: 21/6/2017
37
简体中文
Empty page before back cover
© 2017 Koninklijke Philips N.V.
All rights reserved
保留所有权利
4222.002.7375.1 (21/6/2017)
> 75% 循环再造纸
>75% recycled paper
>75% papier recyclé