Philips SW700M/05 User Manual

Displayed below is the user manual for SW700M/05 by Philips which is a product in the Public Address (PA) Speakers category. This manual has pages.

Related Manuals

Philips SW700M/12 Manual

Philips SPE3031CC/05 Manual

Philips SA9100/05 Manual

Philips FWM377/05 Manual

Philips DTR220/05 Manual

Philips SPE3021CC/05 Manual

Philips SPE3071CC/05 Manual

Philips 240PW9ES/05 Manual

www.philips.com/support

User manual

Always there to help you

SW700M

Question?

Contact

Philips

English

Contents

1 Important 2

Safety 2

Notice 2

2 Your Spotify Multiroom Speaker 4

Introduction 4

What’s in the box 4

What else you need 4

Overview of the main unit 5

3 Prepare 6

Download SpeakerSet Multiroom

Manager to your iOS or Android device 6

Connect power and switch on 6

4 Connect SW700M

to your home

Wi-Fi network 8

Option 1: Set up through an iOS device 8

Option 2: Set up through an Android

device 9

Option 3: Set up wireless connection

to a WPS router directly 10

Option 4: Set up through a PC/Mac

(advanced) 11

Rename speakers 12

5 Play 13

Enjoy Spotify music services through

SW700M 13

Stream music to multiple speakers at

the same time 14

6 Other features 18

Restore factory settings 18

Upgrade rmware 19

7 Product information 20

Specications 20

8 Troubleshooting 21

9 Appendix: Understand meanings

of LED colors 22

2EN

1 Important

Safety

• Only use attachments/accessories specied

by the manufacturer.

• Use only power supplies listed in the user

manual.

• The product shall not be exposed to

dripping or splashing.

• Do not place any sources of danger on the

product (e.g. liquid lled objects, lighted

candles).

• Where the mains plug or an appliance

coupler is used as the disconnect device,

the disconnect device shall remain readily

operable.

Warning

•Never remove the casing of this apparatus.

•Never lubricate any part of this apparatus.

•Never place this apparatus on other electrical

equipment.

•Keep this apparatus away from direct sunlight, naked

ames or heat.

•Ensure that you always have easy access to the power

cord, plug or adaptor to disconnect this apparatus from

the power.

Risk of overheating! Never install this apparatus

in a conned space. Always leave a space of

at least four inches around this apparatus for

ventilation. Ensure curtains or other objects

never cover the ventilation slots on this

apparatus.

Notice

Hereby, WOOX Innovations declares that this

product is in compliance with the essential

requirements and other relevant provisions

of Directive 1999/5/EC. You can nd the

Declaration of Conformity on www.philips.com/

support.

Any changes or modications made to this

device that are not expressly approved by

WOOX Innovations may void the user’s

authority to operate the equipment.

Philips and the Philips’ Shield Emblem are

registered trademarks of Koninklijke Philips N.V.

and are used by WOOX Innovations Limited

under license from Koninklijke Philips N.V.

Specications are subject to change without

notice. WOOX reserves the right to change

products at any time without being obliged to

adjust earlier supplies accordingly.

Disposal of your old product

Your product is designed and manufactured

with high quality materials and components,

which can be recycled and reused.

This symbol on a product means that the

product is covered by European Directive

2012/19/EU. Inform yourself about the local

separate collection system for electrical and

electronic products. Follow local rules and never

dispose of the product with normal household

waste. Correct disposal of old products

helps prevent negative consequences for the

environment and human health.

English

Environmental information

All unnecessary packaging has been omitted.

We have tried to make the packaging easy to

separate into three materials: cardboard (box),

polystyrene foam (buffer) and polyethylene

(bags, protective foam sheet.)

Your system consists of materials which can

be recycled and reused if disassembled by

a specialized company. Please observe the

local regulations regarding the disposal of

packaging materials, exhausted batteries and old

equipment.

Trademark notice

iPad, iPhone, iPod, iPod classic, iPod nano

and iPod touch are trademarks of Apple Inc.,

registered in the U.S. and other countries.

Lightning is a trademark of Apple Inc.

Android is a trademark of Google Inc. Use of

this trademark is subject to Google permissions.

Class II equipment symbol:

CLASS II apparatus with double insulation, and

no protective earth provided.

Note

•The type plate is located on the bottom of the

apparatus.

4EN

2 Your Spotify

Multiroom

Speaker

Congratulations on your purchase, and

welcome to Philips! To fully benet from the

support that Philips offers, register your product

at www.philips.com/welcome.

If you contact Philips, you will be asked for the

model and serial number of this apparatus. The

model number and serial number are on the

bottom of the apparatus. Write the numbers

here:

Model No. __________________________

Serial No. ___________________________

Introduction

With this Spotify Multiroom Speaker, you can:

• stream Spotify music wirelessly via

Spotify Connect with your iOS or

Android device as remote control

• listen to Spotify music everywhere

at your home through group play

(multiple Spotify Multiroom speakers

required)

What’s in the box

Check and identify the contents of your

package:

• Spotify Multiroom Speaker

• 1 x AC power adaptor

• Printed materials

What else you need

To stream Spotify music wirelessly to SW700M

through Wi-Fi, you need:

• a certied Wi-Fi router

• an iOS or Android device, such as an

iPod touch/iPhone/iPad or an Android

phone or tablet

• the SpeakerSet and Spotify (with a

premium account) apps available on

Apple App Store (for iOS devices)

or Google Play Store (for Android

devices)

Your SW700M should be connected to the

same local network as your iOS or Android

device through the Wi-Fi router.

English

Overview of the main unit

a /

• Skip to the previous/next song.

• Start or pause music play.

c +/-

• Adjust volume.

d System status indicator

• Show the current status of the speaker.

e DC IN

• Connect the power adaptor.

f SETUP button/indicator

• Enter App-Assisted Wi-Fi Setup mode

for connection of the speaker to a

Wi-Fi network.

• Show the Wi-Fi setup status.

g WPS button/indicator

• Enter WPS Setup mode for connection

of the speaker to a Wi-Fi network.

• Show the Wi-Fi setup status in WPS

mode.

abc

6EN

3 Prepare

Always follow the instructions in this chapter

in sequence.

Download SpeakerSet

Multiroom Manager to your

iOS or Android device

1 (For iPod touch/iPhone/iPad users) Install

SpeakerSet from Apple App Store, and

then run the app.

(For users of Android smartphones or tablets)

Install SpeakerSet from Google Play Store and

then run the app.

2 On the initial setup page, tap Setup a new

speaker.

Connect power and switch

Caution

•Risk of product damage! Make sure that the power

supply voltage matches the voltage printed on the

bottom of the speaker.

•Risk of electric shock! When you unplug the AC

adaptor, always pull the plug from the socket. Never

pull the cord.

•Before you connect the AC adaptor, make sure that you

have completed all the other connections.

• As instructed on the app screen, connect

the AC power adaptor to

• the DC IN socket on the back of the

speaker.

• the wall power socket.

» The speaker switches on automatically.

English

» The system status indicator on the

front panel blinks amber during

boot-up.

» If a Wi-Fi connection has been set

up for the speaker, the system status

indicator turns solid green after

successful connection.

Tip

•The speaker enters standby mode automatically after

15 minutes of inactivity.

8EN

4 Connect SW700M

to your home

Wi-Fi network

To connect SW700M to your existing home

Wi-Fi network, you need to apply your home

Wi-Fi settings to SW700M in one of the

following ways (depending on the type of your

smart device and whether your Wi-Fi router is

WPS enabled):

Devices

required for

speaker setup

Setup method

iOS device +

Wi-Fi router

Choose option 1 (see

'Option 1: Set up through an

iOS device' on page 8).

Android

device +

Wi-Fi router

Choose option 2 (see

'Option 2: Set up through an

Android device' on page 9).

WPS Wi-Fi

router

Choose option 3 (see

'Option 3: Set up wireless

connection to a WPS router

directly' on page 10).

PC/Mac with

Wi-Fi enabled

+ Wi-Fi router

Choose option 4 (see

'Option 4: Set up through a

PC/Mac (advanced)' on page 11).

Before connection of SW700M to your home

Wi-Fi network, make sure that:

a your Wi-Fi router is powered on and

working properly.

b the speaker has been powered on and

booted up successfully.

c (for option 1, 2 and 4 only) you have

jotted down your Wi-Fi password.

* If your Wi-Fi password contains such special

characters as #/:/;/’, you need to change your

password.

Once connected successfully, SW700M will

remember your home Wi-Fi settings. Whenever

SW700M is powered on, it is connected to your

home Wi-Fi network automatically. Then you can

enjoy Spotify music services via the Spotify app.

Option 1: Set up through an

iOS device

1 Before setup, make sure that your iOS

device is connected to your home Wi-Fi

network.

2 As instructed on the app, press and hold

SETUP on the back of SW700M for more

than 3 seconds.

» Both the system status indicator on

the front panel and the Wi-Fi status

indicator on the SETUP button turns

solid amber.

English

3 Tap Next on the above app screen, and

then read how to proceed with network

setup.

4 Select Wireless (WI-FI) under HOW DO

YOU WANT TO CONNECT?.

5 As instructed, exit the app, and then select

:) Philips Setup from the list of available

Wi-Fi networks.

6 After automatic detection of the speaker

successfully, open the SpeakerSet app again.

7 Select the name of your home Wi-Fi

network under Select a network to use

speaker.

8 Enter the password of your home Wi-Fi

network, and then tap Done to nish

setup.

9 Wait until successful connection of the

speaker to your home Wi-Fi network.

» The speaker beeps.

» The Wi-Fi status indicator on the

SETUP button turns off.

» The system status indicator on the

front panel turns solid green.

Option 2: Set up through an

Android device

1 Before setup, make sure that your Android

device is connected to your home Wi-Fi

network.

2 As instructed on the app, press and hold

SETUP on the back of SW700M for more

than 3 seconds.

» Both the system status indicator on

the front panel and the Wi-Fi status

indicator on the SETUP button turns

solid amber.

10 EN

3 Tap Next on the above app screen, and

then read how to proceed with network

setup.

4 Select Wireless (WI-FI) under HOW DO

YOU WANT TO CONNECT?.

5 Select the name of your home Wi-Fi

network under Select a network to use

speaker.

6 Enter the password of your home Wi-Fi

network, and then tap Done to nish

setup.

7 Wait until successful connection of the

speaker to your home Wi-Fi network.

» The speaker beeps.

» The Wi-Fi status indicator on the

SETUP button turns off.

» The system status indicator on the

front panel turns solid green.

Option 3: Set up wireless

connection to a WPS router

directly

1 As instructed on the app, press and hold

WPS on the back of SW700M for more

than 3 seconds.

» The Wi-Fi status indicator on the WPS

button blinks green.

WPS

English

2 Press the WPS button on your home

Wi-Fi router.

3 Wait until successful connection of the

speaker to your home Wi-Fi network.

» The speaker beeps.

» The Wi-Fi status indicator on the WPS

button turns off.

» The system status indicator on the

front panel turns solid green.

Tip

•Only WPA and WPA2 are supported. If the wireless

security is WEP or no security is applied, the WPS

method does not work.

•For some Wi-Fi routers, you may need to hold the

WPS button for Wi-Fi connection or enable the WPS

PBC function from the router conguration pages. See

the user manuals of the specic routers for details.

WPS

Option 4: Set up through a

PC/Mac (advanced)

1 Go to your Wi-Fi enabled PC/Mac.

2 Press and hold SETUP on the back of

SW700M for more than 3 seconds.

» Both the system status indicator on

the front panel and the Wi-Fi status

indicator on the SETUP button turns

solid amber.

3 Select :) Philips Setup from the list of

available Wi-Fi networks on your PC/Mac.

4 After successful connection, open a web

browser on your PC/Mac.

5 Enter http://philips.speakers or 172.24.0.1

at the address bar and click the Enter key.

6 Make changes on the setup page and

conrm your settings.

» The speaker beeps.

» The Wi-Fi status indicator on the

SETUP button turns off.

» The system status indicator on the

front panel turns solid green.

12 EN

Rename speakers

1 After successful Wi-Fi setup, go to the

home page and tap the speaker icon on

the app screen.

2 Tap > beside the speaker name.

3 Rename the speaker as you like.

4 Tap Done to conrm.

English

5 Play

Enjoy Spotify music services

through SW700M

Note

•With Spotify, you can enjoy unlimited music on your

new device. Thanks to the Spotify Connect feature, you

can play and control all this music wirelessly. Choose

music on your mobile or tablet, and hear it on your

brand new device.

•Make sure that the speaker is connected to your home

Wi-Fi network with Internet connection available.

1 Switch to the Spotify app from SpeakerSet

or open the Spotify app directly.

2 Log in to your Spotify premium account.

Username

Password

3 Tap the Connect icon on the play

screen.

4 Select the speaker for music streaming.

Philips SW700M xxxxxx

14 EN

5 Stream music from the Spotify app to the

speaker.

During play, you can:

• press on the speaker to pause/

resume music play.

• press / on the speaker to skip to

the previous/next song.

• press +/- on the speaker to adjust

volume level.

Tip

•See the SpeakerSet app screen for more advanced

settings.

•You can take your iOS or Android device away from

the network, or even switch it off. In this case, Spotify

music will continue to play on your speaker.

Stream music to multiple

speakers at the same time

You can add multiple Spotify Multiroom

Speakers connected to the same Wi-Fi network

into a group. Then, you can stream music from

Spotify on your iOS or Android device in the

same Wi-Fi network to all speakers in the group

at the same time. In this way, you can enjoy

music everywhere at your home.

Group and ungroup speakers

1 Connect multiple Spotify Multiroom

Speakers to your home Wi-Fi network

(see ‘Connect SW700M to your home

Wi-Fi network’ on page 8).

2 Run SpeakerSet on your iOS/Android

smartphone or tablet.

3 On the home page, tap beside a

speaker to act as the main speaker of a

group.

English

4 Tick circles beside the speakers to add

them into the group.

5 Tap > beside the group name to enter the

edit page.

6 Edit the group name as you like on the edit

page.

7 Tap the check mark at the top right on the

above app screen, and then wait for more

than 10 seconds until the grouping nishes.

To ungroup speakers:

1 Tap beside the main speaker.

2 Untick the box beside the speaker to be

removed from the group.

16 EN

Enjoy music streamed to the group

speakers

1 On the home page, tap the icon of the

main speaker on the SpeakerSet app

screen.

2 Tap Go Spotify app to play music to

switch to the Spotify app.

3 Log in to your Spotify premium account.

4 Tap the Connect icon to select the

main speaker.

5 Select and play your favorite music from

the Spotify app.

» You can enjoy music streamed to all

speakers in the same group at the

same time.

To adjust volume of all speakers in a group at

the same time:

1 Open the SpeakerSet app, then tap

on the main page to enter the volume

adjustment page.

2 Move the group volume slider to adjust

volume of all speakers in the group at the

same time.

English

To adjust volume of an individual speaker:

• Press +/- on the top panel of the speaker.

• Open the SpeakerSet app, then move the

slider beside the speaker on the above

volume adjustment page directly.

To play/pause music play:

• Press on the top panel of any speaker

in the group or use controls on the Spotify

app screen directly.

Tip

•On the volume adjustment page of the SpeakerSet app,

you can also tap beside a speaker to mute/unmute

its volume output.

•More music controls and sound settings are available on

the SpeakerSet app screen.

18 EN

6 Other features

Restore factory settings

In some cases, you may need to reset the

speaker, for example, when you need to reset

the Wi-Fi settings or log out from the current

Spotify premium account.

1 Make sure that SW700M is powered on

and connected to the same Wi-Fi network

as your smartphone or tablet.

2 Make sure that your home Wi-Fi network

is connected to the Internet.

3 Run SpeakerSet on your iOS or Android

smartphone or tablet.

4 Tap the speaker image to see options

available for the speaker.

5 Tap Factory reset to enter the factory

reset page.

6 Tap Ye s to reset your speaker.

If the above operation fails, you can reset the

speaker in the following way:

1 Unplug the power cable.

2 Hold both the + and keys on the top

panel and then plug in the power cable

again.

Tip

•The speaker reboots after factory reset.

•Your Spotify account will be logged out after factory

reset.

•If the reset speaker is running in a group, it will be

ungrouped. When the main speaker is reset, one of

the other speakers in the group will serve as the main

speaker instead.

English

Upgrade rmware

To improve the performance of SW700M, Philips

may offer you new rmware for upgrade of your

SW700M.

Warning

•Always connect your SW700M to AC power for

rmware upgrade. Never power off your SW700M nor

close the app during rmware upgrade.

1 Make sure that SW700M is powered on and

connected to the same Wi-Fi network as

your smartphone or tablet.

2 Make sure that your home Wi-Fi network is

connected to the Internet.

3 Run SpeakerSet on your iOS or Android

smartphone or tablet.

4 Tap the speaker image to see options

available for the speaker.

5 Tap Firmwareupgrade to enter the

rmware upgrade page.

6 Tap Check online to see whether any new

version of rmware is available.

7 If a new version is available, tap Update to

start rmware upgrade.

» The system status indicator on the

front panel blinks amber and red

alternately during this process.

8 Wait until the rmware upgrade process

nishes, then tap OK to reboot the

speaker.

Tip

•Depending on the network connection, it may take 10

minutes to nish upgrade.

20 EN

7 Product

information

Note

•Product information is subject to change without prior

notice.

Specications

Amplier

Rated Output Power 2 x 2W RMS @

10% THD

Frequency Response 20 Hz - 20 kHz,

±3 dB

Signal to Noise Ratio > 85 dB

Speakers

Speaker Impedance 8 ohm

Speaker Driver 66 mm full range

Sensitivity 83dB/m/W

Wireless

standard

802.11b/g/n

Wireless

security

WEP, 10 or 26 hex digit keys

WPA (TKIP) or WPA2

(TKIP / AES) with 8 - 40

ASCII printable characters

passphrase

Frequency

range

2412 - 2462 MHz (CH1-

CH11) (for /79, /37, /55, /97)

2412 - 2472 MHz (CH1-

CH13) (for /12, /10, /05)

WPS PBC

(one button

push)

Ye s

General information

AC power

PHILIPS

SWITCHING

POWER SUPPLY

Model: TPA158B-

12150-EU; input:

100 - 240 V~, 50/60 Hz

0.5A MAX; output:

15V 0.8 A

Model: OH-

1015E1500800U1;

input: 100 - 240 V~,

50/60Hz, 350mA;

output: 15V 800 mA

Operation Power

Consumption

12 W

Power Consumption

in Network Standby

< 3 W

Dimensions

- Main Unit (L x W

x H)

288 x 170 x 95 mm

Weight

- Main Unit 1.1 kg

English

8 Troubleshooting

Warning

•Never remove the casing of this apparatus.

To keep the warranty valid, never try to repair the

system yourself.

If you encounter problems when using this

apparatus, check the following points before

requesting service. If the problem remains

unsolved, go to the Philips web site (www.philips.

com/welcome). When you contact Philips, ensure

that the apparatus is nearby and the model

number and serial number are available.

No power

•Make sure that the AC power plug of the

speaker is connected properly.

•Make sure that there is power at the AC

outlet.

•Check whether the speaker is in standby

mode (see ‘Connect power and switch on’

on page 6).

No sound

•Check whether the speaker is muted or

the streamed music is still buffering. The

system status indicator blinks green when the

speaker is muted or during music buffering. If

the speaker is muted, adjust volume on the

SpeakerSet app or on SW700M directly.

•Check the Wi-Fi network connection. Set up

the network again if needed (see ‘Connect

SW700M to your home Wi-Fi network’ on

page 8).

•If there is no sound from a speaker in a

group, check whether the speaker is out of

range. You can check whether the wireless

connection of the speaker is poor on the app

screen directly.

No response from the speaker

•Restart SW700M, and then set up the Wi-Fi

network for SW700M again (see ‘Connect

SW700M to your home Wi-Fi network’ on

page 8).

•Disconnect and reconnect the AC power

plug to switch on the speaker again.

•If there is no sound from a speaker in a

group, check whether the speaker is out of

range. You can check whether the wireless

connection of the speaker is poor on the

app screen directly.

How can I recongure the Wi-Fi settings?

•Reset the speaker (see ‘Restore factory

settings’ on page 17), and then congure

the Wi-Fi settings again (see ‘Connect

SW700M to your home Wi-Fi network’ on

page 8).

Occasional breaking of music streaming

Do one or all of the following:

•Move SW700M closer to your Wi-Fi

router.

•Remove any obstacles between SW700M

and your Wi-Fi router.

•Avoid using Wi-Fi channel which is

overlapped by the nearby Wi-Fi network.

•Check if your network speed is fast enough

(in cases where multiple devices share the

same router, the wireless performance may

be affected). Turn off the other devices

connected to your home router.

•Enable the Quality of Service (QoS)

option (if available on the Wi-Fi router).

•Turn off other Wi-Fi routers.

No response from the speaker

•Restart SW700M, and then set up the

Wi-Fi network for SW700M again (see

‘Connect SW700M to your home Wi-Fi

network’ on page 8).

•Disconnect and reconnect the AC power

plug to switch on the speaker again.

•If there is no sound from a speaker in a

group, check whether the speaker is out of

range. You can check whether the wireless

connection of the speaker is poor on the

app screen directly.

131 blinking amber

quickly, and 3 blinking

green

In WPS

mode

11 solid green Network

connection

successful

11 blinking green

quickly

During audio

buffering

11 blinking green

slowly

Muted or

playback

paused

11 dimmed by 50% in

solid green

In standby

mode with

network

connection

11 solid red In standby

mode

without

network

connection

11 blinking red Network

connection

failed

1 2 1 solid red, and 2

solid amber

During

factory reset

11 blinking red and

amber

During

rmware

upgrade

11 blinking red, amber

and green alternately

Firmware

upgrade

failed

9 Appendix:

Understand

meanings of

LED colors

a System status indicator (on the front

panel)

b SETUP indicator (on the back panel)

c WPS indicator (on the back panel)

LED

colors

LED behavior Speaker

status

No light Power off

11 blinking amber

slowly

Booting up

11 blinking amber

quickly

Connecting

to a

network

1 2 1 and 2 indicators in

solid amber

In app-

assisted

Wi-Fi setup

mode

Open Source Declaration for Philips

SW700M/SW750M/SW100M

ALAC

FLAC

Iperf

jQuery

JSBN 1.2

Jungo USB DFU Driver

Marvell WPS2 Client

mDNSResponder

OpenSSL

RSA MD5

zlib

getopt

Mongoose

Tremor

ALAC

http://alac.macosforge.org/

The Apple Lossless Audio Codec sources are available under the Apache license. Details can be

found here http://www.apache.org/licenses/LICENSE-2.0.

FLAC

https://xiph.org/flac/license.html

The FLAC and Ogg FLAC formats themselves, and their specifications, are fully open to the

public to be used for any purpose (the FLAC project reserves the right to set the FLAC

specification and certify compliance). They are free for commercial or noncommercial use. That

means that commercial developers may independently write FLAC or Ogg FLAC software which

is compatible with the specifications for no charge and without restrictions of any kind. There

are no licensing fees or royalties of any kind for use of the formats or their specifications, or for

distributing, selling, or streaming media in the FLAC or Ogg FLAC formats.

The FLAC project also makes available software that implements the formats, which is

distributed according to Open Source licenses as follows:

The reference implementation libraries are licensed under the New BSD License. In simple

terms, these libraries may be used by any application, Open or proprietary, linked or

incorporated in whole, so long as acknowledgement is made to Xiph.org Foundation when

using the source code in whole or in derived works. The Xiph License is free enough that the

libraries have been used in commercial products to implement FLAC, including in the firmware

of hardware devices where other Open Source licenses can be problematic. In the source code

these libraries are called libFLAC and libFLAC++.

The rest of the software that the FLAC project provides is licensed under the GNU General

Public License (GPL). This software includes various utilities for converting files to and from

FLAC format, plugins for audio players, et cetera. In general, the GPL allows redistribution as

long as derived works are also made available in source code form according to compatible

terms.

Neither the FLAC nor Ogg FLAC formats nor any of the implemented encoding/decoding

methods are covered by any known patent.

FLAC is one of a family of codecs of the Xiph.org Foundation, all created according to the same

free ideals. For some other codecs' descriptions of the Xiph License see

the Speex and Vorbis license pages.

Iperf

http://pirlwww.lpl.arizona.edu/resources/guide/software/iperf/

The Board of Trustees of the University of Illinois

Permission is hereby granted, free of charge, to any person obtaining a copy of this software

(Iperf) and associated documentation files (the "Software"), to deal in the Software without

restriction, including without limitation the rights to use, copy, modify, merge, publish,

distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the

Software is furnished to do so, subject to the following conditions:

Redistributions of source code must retain the above copyright notice, this list of

conditions and the following disclaimers.

Redistributions in binary form must reproduce the above copyright notice, this list of

conditions and the following disclaimers in the documentation and/or other materials

provided with the distribution.

Neither the names of the University of Illinois, NCSA, nor the names of its contributors

may be used to endorse or promote products derived from this Software without

specific prior written permission.

THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED,

INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A

PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE CONTIBUTORS OR

AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION

WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.

See UI License for complete details.

jQuery

http://jquery.org

jQuery projects are released under the terms of the MIT license.

The MIT License is simple and easy to understand and it places almost no restrictions on what

you can do with a jQuery project.

You are free to use any jQuery project in any other project (even commercial projects) as long

as the copyright header is left intact.

JSBN

jsbn is released under a BSD license. See LICENSE for details.

Licensing

---------

This software is covered under the following copyright:

* Permission is hereby granted, free of charge, to any person obtaining

* a copy of this software and associated documentation files (the

* "Software"), to deal in the Software without restriction, including

* without limitation the rights to use, copy, modify, merge, publish,

* distribute, sublicense, and/or sell copies of the Software, and to

* permit persons to whom the Software is furnished to do so, subject to

* the following conditions:

* The above copyright notice and this permission notice shall be

* included in all copies or substantial portions of the Software.

* THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND,

* EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY

* WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

* IN NO EVENT SHALL TOM WU BE LIABLE FOR ANY SPECIAL, INCIDENTAL,

* INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND, OR ANY DAMAGES WHATSOEVER

* RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER OR NOT ADVISED OF

* THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF LIABILITY, ARISING OUT

* OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.

* In addition, the following condition applies:

* All redistributions must retain an intact copy of this copyright notice

* and disclaimer.

Address all questions regarding this license to:

Tom Wu

tjw@cs.Stanford.EDU

Jungo USB DFU Driver

http://www.jungo.com/st/products/drivercore-advanced-usb-drivers/

BSD license

Marvell WPS2 client

http://www.marvell.com/

BSD license

mDNSResponder

http://www.opensource.apple.com/source/mDNSResponder/mDNSResponder-320.10.80/

The majority of the source code in the mDNSResponder project is licensed

under the terms of the Apache License, Version 2.0, available from:

<http://www.apache.org/licenses/LICENSE-2.0>

To accommodate license compatibility with the widest possible range

of client code licenses, the shared library code, which is linked

at runtime into the same address space as the client using it, is

licensed under the terms of the "Three-Clause BSD License".

The Linux Name Service Switch code, contributed by National ICT

Australia Ltd (NICTA) is licensed under the terms of the NICTA Public

Software Licence (which is substantially similar to the "Three-Clause

BSD License", with some additional language pertaining to Australian law).

OpenSSL

http://www.openssl.org

OpenSSL is based on the SSLeay library developed by Eric Young and Tim Hudson. The OpenSSL

toolkit is licensed under an Apache-style licence which basically means that you are free to get

and use it for commercial and non-commercial purposes.

RSA MD5

/* MD5C.C - RSA Data Security, Inc., MD5 message-digest algorithm

* rights reserved.

* License to copy and use this software is granted provided that it

* is identified as the "RSA Data Security, Inc. MD5 Message-Digest

* Algorithm" in all material mentioning or referencing this software

* or this function.

* License is also granted to make and use derivative works provided

* that such works are identified as "derived from the RSA Data

* Security, Inc. MD5 Message-Digest Algorithm" in all material

* mentioning or referencing the derived work.

* RSA Data Security, Inc. makes no representations concerning either

* the merchantability of this software or the suitability of this

* software for any particular purpose. It is provided "as is"

* without express or implied warranty of any kind.

* These notices must be retained in any copies of any part of this

* documentation and/or software.

Zlib

http://www.zlib.net/

/* zlib.h -- interface of the 'zlib' general purpose compression library

version 1.2.8, April 28th, 2013

This software is provided 'as-is', without any express or implied

warranty. In no event will the authors be held liable for any damages

arising from the use of this software.

Permission is granted to anyone to use this software for any purpose,

including commercial applications, and to alter it and redistribute it

freely, subject to the following restrictions:

1. The origin of this software must not be misrepresented; you must not

claim that you wrote the original software. If you use this software

in a product, an acknowledgment in the product documentation would be

appreciated but is not required.

2. Altered source versions must be plainly marked as such, and must not be

misrepresented as being the original software.

3. This notice may not be removed or altered from any source distribution.

Jean-loup Gailly Mark Adler

jloup@gzip.org madler@alumni.caltech.edu

getopt

http://cvsweb.netbsd.org/bsdweb.cgi/src/lib/libc/stdlib/

BSD license

Mongoose

https://github.com/cesanta/mongoose/

Mongoose is released under commercial and GNU GPL v.2 open source licenses. The GPLv2

open source License does not generally permit incorporating this software into non-open

source programs. For those customers who do not wish to comply with the GPLv2 open source

license requirements,Cesanta Software offers a full, royalty-free commercial license and

professional support without any of the GPL restrictions.

Tremor

http://wiki.xiph.org/index.php/Tremor

BSD license

Philips and the Philips’ Shield Emblem are registered trademarks

of Koninklijke Philips N.V. and are used by WOOX Innovations

Limited under license from Koninklijke Philips N.V.

SW700M_UM_EN_05_V2.0

Table of Contents

Philips SW700M/05 User Manual

Related Manuals