Table of Contents
- Contents
- 1. Preface
- 2. Product Overview
- 3. Installation and Configuration
- 4. Basic Operations
- 5. Troubleshooting
- 6. Glossary
- 7. Notices
QNAP QGD-3014-16PT-8G User Manual
Displayed below is the user manual for QGD-3014-16PT-8G by QNAP which is a product in the Network Switches category. This manual has pages.
Related Manuals
QGD-3014-16PT
User Guide
Document Version: 2
30/10/2020
Contents
1. Preface
About This Guide.......................................................................................................................................... 3
Audience.......................................................................................................................................................3
Document Conventions................................................................................................................................ 3
2. Product Overview
About the QGD-3014-16PT.......................................................................................................................... 4
Hardware Specifications............................................................................................................................... 4
Package Contents........................................................................................................................................ 6
Components................................................................................................................................................. 7
Front Panel...............................................................................................................................................7
Rear Panel................................................................................................................................................8
Rear Panel LEDs......................................................................................................................................8
System Board...........................................................................................................................................9
Drive Numbering.......................................................................................................................................9
Safety Information.......................................................................................................................................10
Installation Requirements............................................................................................................................11
Setting Up the Switch..................................................................................................................................11
3. Installation and Configuration
Hardware Installation.................................................................................................................................. 13
Removing the Case Cover..................................................................................................................... 13
Attaching the Case Cover.......................................................................................................................14
Drive Installation.....................................................................................................................................15
Replacing Memory Modules...................................................................................................................28
Connecting the Switch to a Computer or Network..................................................................................31
Connecting USB Expansion Units..........................................................................................................33
QTS Installation.......................................................................................................................................... 34
Installing QTS Using Qfinder Pro........................................................................................................... 35
Installing QTS Using the Cloud Key....................................................................................................... 36
Switch Management Application Access.................................................................................................... 37
Accessing QSS with Qfinder Pro............................................................................................................38
Accessing QuNetSwitch in QTS.............................................................................................................38
4. Basic Operations
Buttons........................................................................................................................................................40
Power Button..........................................................................................................................................40
Switch Reset Button............................................................................................................................... 40
QTS Reset Button.................................................................................................................................. 40
LCD Panel.................................................................................................................................................. 41
Viewing TCP/IP Settings........................................................................................................................ 41
Configuring TCP/IP Settings...................................................................................................................41
Viewing Drive Information.......................................................................................................................42
Viewing System Information...................................................................................................................42
Powering Off the Switch......................................................................................................................... 43
Restarting the Switch..............................................................................................................................43
Changing the LCD Password................................................................................................................. 43
LCD Error Messages..............................................................................................................................44
LEDs........................................................................................................................................................... 44
Audio Alert.................................................................................................................................................. 45
QGD-3014-16PT User Guide
1
5. Troubleshooting
Hot-Swapping Failed Drives....................................................................................................................... 47
Recovering Unintentionally Removed Healthy Drives................................................................................ 47
Forcing Qfinder Pro and myQNAPcloud to Locate the Switch................................................................... 48
Support and Other Resources.................................................................................................................... 48
6. Glossary
myQNAPcloud............................................................................................................................................ 49
myQNAPcloud Link.....................................................................................................................................49
Qfinder Pro................................................................................................................................................. 49
QSS............................................................................................................................................................ 49
QTS.............................................................................................................................................................49
QuNetSwitch...............................................................................................................................................49
7. Notices
Limited Warranty.........................................................................................................................................50
Disclaimer................................................................................................................................................... 50
GNU Public License....................................................................................................................................50
CE Notice....................................................................................................................................................58
FCC Notice................................................................................................................................................. 58
VCCI Notice................................................................................................................................................ 58
BSMI Notice................................................................................................................................................59
SJ/T 11364-2006.........................................................................................................................................59
2
1. Preface
About This Guide
This guide provides information about the device and step-by-step instructions on installing the hardware. It
also provides instructions on basic operations and troubleshooting information.
Audience
This document is intended for consumers and storage administrators. This guide assumes that the user has
a basic understanding of storage and backup concepts.
Document Conventions
Symbol Description
Notes provide default configuration settings and other supplementary
information.
Important notes provide information on required configuration settings and other
critical information.
Tips provide recommendations or alternative methods of performing tasks or
configuring settings.
Warnings provide information that, when ignored, may result in potential loss,
injury, or even death.
QGD-3014-16PT User Guide
Preface 3
2. Product Overview
This chapter provides basic information about the QNAP device.
About the QGD-3014-16PT
The QGD-3014-16PT is a QNAP smart-edge network switch specially designed for surveillance applications.
The switch features built-in storage capacity that can house four 3.5-inch SATA hard drives, software-defined
networking (SDN) to support multiple SMB applications, including NAS, NVR, router, surveillance, and virtual
machines. The QGD-3014-16PT features 16-port 30-watt Gigabit power over Ethernet (PoE) and two
2.5GbE host management ports for fast data transfer. The switch's dual-CPU design offers Layer 2
management functions for VM and QTS applications.
Hardware Specifications
Warning
If your QNAP product has hardware defects, return the product to QNAP or a QNAP-
authorized service center for maintenance or replacement. Any attempt to repair or
perform maintenance procedures on the product by you or an unauthorized third-party
invalidates the warranty.
QNAP is not responsible for any damage or data loss caused by unauthorized
modifications and installation of unsupported third-party applications.
For details, see the QNAP Warranty Terms and Conditions.
Tip
Model specifications are subject to change without prior notice. To see the latest
specifications, go to https://www.qnap.com.
Ordering P/N CPU Memory Power supply
QGD-3014-16PT-8G Intel Celeron ® J4125 8 GB Single
Component QGD-3014-16PT-8G
Processor
CPU Intel Celeron ® J4125
Frequency 4-core/4-thread 2.0 GHz base/ 2.7 GHz burst
Architecture x86 64-bit
Encryption engine AES-NI
Graphics Intel® HD Graphics 600
Memory
Pre-installed memory 8 GB RAM: 2 x 4 GB DDR4 SODIMM
Memory slots 2 x DDR4 SODIMM
Note
Use only QNAP memory modules to maintain system
performance and stability. For devices with more than
one memory slot, use QNAP modules with identical
specifications.
Using unsupported modules may degrade performance,
cause errors, or prevent the operating system from
starting.
QGD-3014-16PT User Guide
Product Overview 4
Component QGD-3014-16PT-8G
Maximum memory 8 GB RAM: 2 x 4 GB
Flash memory 4 GB (dual-boot OS protection)
Storage
Drive bays 4 x 3.5-inch SATA 6 Gbps
Note
The 3.5-inch SATA 6 Gbps drive bays are backward
compatible with SATA 3 Gbps drives.
Drive compatibility 3.5-inch bays:
• 3.5-inch SATA hard disk drives
• 3.5-inch SATA solid-state drives
• 2.5-inch SATA hard disk drives
• 2.5-inch SATA solid-state drives
M.2 SSD slots 2 x M.2 SATA
M.2 SSD form factor 2230
SSD cache acceleration support 3.5-inch drive bays:1-4
Hot-swapping Supported
Network
2.5 Gigabit Ethernet ports 2 x 2.5 GbE RJ45
Gigabit Ethernet ports • 2 x 1 GbE RJ45/SFP combo ports
• 14 x 1 GbE RJ45
PoE support
802.3at (PoE+) Ports 1 to 16
Note
The ports support IEEE 802.3at-2009 PoE standard
and provide up to 30W of DC power.
PoE max power port 30W
Total PoE power budget 140W
Total power consumption 250W
External I/O Ports & Expansion Slots
USB ports Front:
1 x USB 3.0 Type-A
Note
This USB port supports One Touch Copy.
Rear:
2 x USB 3.0 Type-A
HDMI ports 2 x HDMI 2.0 (up to 3840 x 2160 resolution at 30 Hz with HDR)
QGD-3014-16PT User Guide
Product Overview 5
Component QGD-3014-16PT-8G
Audio ports • 1 x 3.5 mm dynamic microphone jacks
• 1 x 3.5 mm line-out jack
Note
You cannot use speakers and line-out jacks
simultaneously.
Interface
Display panel Monochrome backlit LCD display
Buttons • Enter
• Select
• Power
• Switch reset button
• Host reset button
• USB One Touch Copy
Dimensions
Form factor Tower
Dimensions (H x W x D) 130 x 295 x 224.8 mm
(5.12 x 11.61 x 8.85 in)
Net weight 4.08 kg (8.99 lbs)
System battery CR2032 lithium battery (3V, 225 mAh)
Fans 1 x 120 mm, 12V DC fan
Operating temperature 0˚C to 40˚C (32˚F to 104˚F)
Relative humidity • Non-condensing relative humidity: 5% to 95%
• Wet-bulb temperature: 27˚C (80.6˚F)
Tip
For the list of compatible drive models and expansion cards, go to https://www.qnap.com/
compatibility.
Package Contents
Item Quantity
QGD-3014-16PT 1
AC power adapter 1
Power cord 1
Ethernet cables 1 x 1GbE (RJ45)
Drive tray key 1
Screws for 3.5-inch drives 16
Screws for 2.5-inch drives 12
Quick Installation Guide (QIG) 1
QGD-3014-16PT User Guide
Product Overview 6
Components
Front Panel
No. Component No. Component
1 LCD panel 7 Drive LEDs
2 Enter button 8 Status LED
3 Select button 9 Switch status LED
4 USB 3.2 Gen 1 One Touch Copy Type-A port 10 PoE LED
5 USB One Touch Copy button 11 Fan LED
6 Power button 12 Warning LED
QGD-3014-16PT User Guide
Product Overview 7
Rear Panel
No. Component No. Component
1 Host reset button 6 2.5 Gigabit Ethernet ports (RJ45)
2 Switch reset button 7 HDMI 2.0 ports
3 3.5 mm line-out jack 8 Gigabit 802.3at PoE+ RJ45 ports
4 3.5 mm dynamic microphone jack 9 Gigabit RJ45/SFP combo ports
5 USB 3.0 Type-A ports 10 Power input
Rear Panel LEDs
QGD-3014-16PT User Guide
Product Overview 8
No. Component No. Component
1 2.5 Gigabit Ethernet activity LED 4 Gigabit 802.3at PoE+ port activity LED
2 2.5 Gigabit Ethernet speed LED 5 Combo port activity LED
3 Gigabit 802.3at PoE+ port speed LED 6 Combo port speed LED
System Board
No. Component No. Component
1 M.2 SSD slot 1 3 Memory slot 1
2 M.2 SSD slot 2 4 Memory slot 2
Drive Numbering
QGD-3014-16PT User Guide
Product Overview 9
Note
This image shows the switch with the front panel removed.
Safety Information
The following instructions help ensure personal safety and environmental safety. Read these instructions
carefully before performing any operations.
General Instructions
• The device should be stored in a secure location with restricted access, controlled through the use of a
tool, lock and key, or any means of security.
• Only qualified, skilled, and authorized persons with knowledge of all restrictions, safety precautions,
and installation and maintenance procedures should have physical access to the device.
• To avoid potential injury or damage to components, ensure that the drives and other internal system
components have cooled before touching them.
• Observe electrostatic discharge (ESD) procedures to avoid potential injury or damage to components.
Power
• To reduce the risk of fire or electric shock, ensure that you only connect the power cord to a properly
grounded electrical outlet.
•
Devices with redundant power supply may have one or more power supply unit (PSU) cords. To avoid
serious injuries, a trained service technician must disconnect all PSU cords from the device before
installing or replacing system components.
System Battery
• To avoid potential battery explosion, causing injury or damage to components, ensure that you replace
the existing battery with a battery of the same type.
• Dispose of used batteries properly according to local regulations or the instructions of the battery
manufacturer.
Moving Parts
•
Moving fan blades: Keep your body parts away from moving fan blades while the device is connected
to a power source.
•
Moving components: Keep your body parts away from other moving components.
QGD-3014-16PT User Guide
Product Overview 10
Installation Requirements
Category Item
Environment • Room temperature: 0˚C to 40˚C (32˚F to 104˚F)
• Non-condensing relative humidity: 5% to 95%
• Wet-bulb temperature: 27˚C (80.6˚F)
• Flat, anti-static surface without exposure to direct sunlight, liquids,
or chemicals
• Free from objects that may obstruct the switch ventilation or apply
pressure to the switch or power cord.
Hardware and peripherals • Computer or NAS
• Storage drives
For the list of compatible drive models, go to https://
www.qnap.com/compatibility.
• Network cable
Tools • Phillips #1 or #2 screwdriver
• Flat head screwdriver
• Anti-static wrist strap
Setting Up the Switch
1. Place your switch in an environment that meets the requirements.
For details, see Installation Requirements.
2. Install the drives.
For details, see the following topics:
•Installing 3.5-inch Hard Drives or Solid-State Drives on 3.5-inch Trays
•Installing 2.5-inch Hard Drives or Solid-State Drives on 3.5-inch Trays
•Installing M.2 Solid-State Drives
For a list of compatible drives, go to http://www.qnap.com/compatibility
3. Optional: Replace memory modules.
For details, see Replacing Memory Modules.
4. Power on the switch.
For details, see Front Panel.
5. Connect the switch to a computer or network.
For details, see Connecting the Switch to a Computer or Network.
6. Install QTS.
For details, see QTS Installation.
7. Log on to QTS.
QGD-3014-16PT User Guide
Product Overview 11
3. Installation and Configuration
This chapter provides specific hardware and firmware installation and configuration steps.
Hardware Installation
This section provides information on installing drives, memory modules, and expansion cards.
Removing the Case Cover
1. Power off the device.
2. Disconnect the power cord from the electrical outlet.
3. Disconnect all cables and external attachments.
4. Remove the case cover.
a. Loosen the screws.
b. Slide the cover back.
c. Lift the cover off the device.
QGD-3014-16PT User Guide
Installation and Configuration 13
Attaching the Case Cover
1. Place the cover on the device.
2. Slide the cover forward.
3. Attach the screws.
QGD-3014-16PT User Guide
Installation and Configuration 14
4. Connect all cables and external attachments.
5. Connect the power cord to the electrical outlet.
6. Power on the device.
Drive Installation
The QGD-3014-16PT is compatible with 3.5-inch hard disk drives, 3.5-inch solid-state drives, 2.5-inch solid-
state drives, and 2.5-inch hard disk drives.
Installing 3.5-inch Hard Drives on 3.5-inch Trays
Warning
• Installing a drive deletes all data on the drive.
• Observe electrostatic discharge (ESD) procedures to avoid damage to components.
•
Moving fan blades: Keep your hands and other body parts away from moving fan
blades.
•
Other moving components: Keep your hands and other body parts away from other
moving components.
1. Power off the switch.
2. Remove the front cover.
QGD-3014-16PT User Guide
Installation and Configuration 15
a. Locate the locking mechanism on the left side of the switch.
b. Slide the lock down to release the front cover.
c. Slide the front cover to the left and then pull.
3. Remove the drive tray.
a. Optional: Unlock the tray.
QGD-3014-16PT User Guide
Installation and Configuration 16
Note
The preinstalled drive trays come unlocked.
Important
Ensure the drive tray keys are stored in a safe place.
b. Pull the handle to release the tray.
c. Pull the tray out.
4. Install a drive on the tray.
a. Place the drive on the tray so that the holes on the sides of the drive are aligned with the holes on
the sides of the tray.
QGD-3014-16PT User Guide
Installation and Configuration 17
b. Optional: Attach the screws to further secure the drive.
5. Load the tray into the bay.
a. Insert the tray into the bay.
b. Push the handle.
c. Lock the tray.
QGD-3014-16PT User Guide
Installation and Configuration 18
6. Attach the front cover.
a. Align the front cover with the grooves on the case and then slide to the right.
b. Slide the lock up to secure the front cover.
QGD-3014-16PT User Guide
Installation and Configuration 19
7. Power on the switch.
Installing 2.5-inch Hard Drives and Solid-State Drives on 3.5-inch Trays
Warning
• Installing a drive deletes all data on the drive.
• Observe electrostatic discharge (ESD) procedures to avoid damage to components.
•
Moving fan blades: Keep your hands and other body parts away from moving fan
blades.
•
Other moving components: Keep your hands and other body parts away from other
moving components.
1. Power off the switch.
2. Remove the front cover.
a. Locate the locking mechanism on the left side of the switch.
QGD-3014-16PT User Guide
Installation and Configuration 20
b. Slide the lock down to release the front cover.
c. Slide the front cover to the left and then pull.
3. Remove the drive tray.
a. Optional: Unlock the tray.
QGD-3014-16PT User Guide
Installation and Configuration 21
Note
The preinstalled drive trays come unlocked.
Important
Ensure the drive tray keys are stored in a safe place.
b. Pull the handle to release the tray.
c. Pull the tray out.
4. Install a drive on the tray.
a. Place the drive on the tray so that the holes on the bottom of the drive are aligned with the holes
on the bottom of the tray.
QGD-3014-16PT User Guide
Installation and Configuration 22
b. Attach the screws.
5. Load the tray into the bay.
a. Insert the tray into the bay.
b. Push the handle.
c. Lock the tray.
QGD-3014-16PT User Guide
Installation and Configuration 23
6. Attach the front cover.
a. Align the front cover with the grooves on the case and then slide to the right.
b. Slide the lock up to secure the front cover.
QGD-3014-16PT User Guide
Installation and Configuration 24
7. Power on the switch.
Installing M.2 Solid-State Drives
The device has two M.2 SSD slots on the system board.
For details, see System Board.
For a list of compatible M.2 SSDs, go to http://www.qnap.com/compatibility.
Warning
• Installing a drive deletes all data on the drive.
• Observe electrostatic discharge (ESD) procedures to avoid damage to components.
•
Moving fan blades: Keep your hands and other body parts away from moving fan
blades.
•
Other moving components: Keep your hands and other body parts away from other
moving components.
Note
• QNAP recommends installing heatsinks on the M.2 SSD controllers to enhance cooling
efficiency and to ensure consistent performance.
QGD-3014-16PT User Guide
Installation and Configuration 25
• Before installing non-QNAP heatsinks, ensure that they are of the appropriate size and
shape.
1. Power off the device.
2. Remove the case cover.
For details, see Removing the Case Cover.
3. Install a heatsink on the M.2 SSD.
a. Locate the controller on the M.2 SSD.
Note
The controller location varies depending on the model and manufacturer of the M.2 SSD.
For details, refer to the documentation or contact the manufacturer.
b. Remove the protective film from the heatsink.
c. Install the heatsink on the controller.
QGD-3014-16PT User Guide
Installation and Configuration 26
4. Install the M.2 SSD.
a. Pull out the pushpin.
b. Insert the M.2 SSD into the slot.
c. Push down the M.2 SSD.
QGD-3014-16PT User Guide
Installation and Configuration 27
d. Insert the pushpin to secure the drive.
5. Attach the case cover.
For details, see Attaching the Case Cover.
6. Power on the device.
Replacing Memory Modules
The QGD-3014-16PT has two memory slots. You can increase the memory capacity of the switch by
upgrading memory modules.
Use only QNAP memory modules to maintain system performance and stability. You can purchase QNAP
memory modules from authorized resellers.
For details on slot numbering, see System Board.
QGD-3014-16PT User Guide
Installation and Configuration 28
Warning
• Installing a drive deletes all data on the drive.
• Observe electrostatic discharge (ESD) procedures to avoid damage to components.
•
Moving fan blades: Keep your hands and other body parts away from moving fan
blades.
•
Other moving components: Keep your hands and other body parts away from other
moving components.
1. Power off the device.
2. Remove the case cover.
For details, see Removing the Case Cover.
3. Remove an existing module.
a. Push the retention clips outward simultaneously to release the module.
Warning
Attempting to remove a module that is not completely released may damage the module and
the motherboard.
b. Verify that the module has tilted upward and is completely released from the slot.
c. Hold the module by the edges.
QGD-3014-16PT User Guide
Installation and Configuration 29
d. Carefully slide the module out of the slot.
Warning
• Do not touch the internal components, particularly the metal connectors.
• Do not bend the module.
4. Install a new module.
a. Align the notch with the ridge in the slot.
b. Insert the module into the slot.
c. Verify that the metal connectors are completely inserted into the slot.
d. Carefully press down on the module until the retention clips lock the module into place.
QGD-3014-16PT User Guide
Installation and Configuration 30
5. Attach the case cover.
Note
For details, see Attaching the Case Cover.
6. Power on the device.
7. Verify that the module is recognized by the device.
a. Log on to QTS as administrator.
b. Go to Control Panel > System > System Status > Hardware Information .
c. Check the value for Total memory.
Connecting the Switch to a Computer or Network
The QGD-3014-16PT can be connected to a computer or local area network. For details, see the following
topics:
•Connecting the Switch to a Computer
•Connecting the Switch to a Network
Connecting the Switch to a Computer
Connecting the QGD-3014-16PT to a QNAP NAS allows you to expand storage capacity and backup data to
another NAS through Ethernet cable connections to a PoE port on the switch. However, you must connect
the QGD-3014-16PT to a computer to configure switch settings.
1. Power on the switch.
2. Connect the switch to a computer.
a. Connect an Ethernet cable to a PoE port on the switch.
b. Connect the Ethernet cable to a Gigabit Ethernet port on the computer.
QGD-3014-16PT User Guide
Installation and Configuration 31
3. Verify that the switch is recognized by the computer.
a. Open Qfinder Pro on the host computer.
Note
To download Qfinder Pro, go to https://www.qnap.com/utilities.
b. Locate the switch on the list.
Connecting the Switch to a Network
The QGD-3014-16PT can connect to the local area network through the host port or a PoE port.
1. Power on the switch.
2. Connect the switch to your local area network through one of the following port types:
Type Method
Host Port Select the switch IP address obtained from Adapter 1 on the LCD
panel.
PoE Port Select switch IP addresses obtained from Adapter 2 or Adapter 3
on the LCD panel.
3. Run Qfinder Pro on a computer that is connected to the same local area network.
Note
To download Qfinder Pro, go to https://www.qnap.com/utilities.
4. Enter the IP address in the Qfinder Pro search bar.
5. Locate the switch in the list and then double-click the name or IP address.
The QTS login screen appears.
6. Enter your QTS login information.
QGD-3014-16PT User Guide
Installation and Configuration 32
7. Click Log In.
Connecting USB Expansion Units
The device supports USB expansion units. For details, please see table below.
You can purchase storage expansion accessories from QNAP or an authorized reseller.
For details, go to https://shop.qnap.com/.
For the list of compatible expansion units and the maximum number of applicable expansion units, go to
http://www.qnap.com/go/compatibility-expansion.
Expansion Unit Model Description Required Accessories
TR-002 • Uses a USB 3.2 Gen 2 Type-C
interface
• Supports SATA drives
USB 3.2 Gen 2 Type-A to Type-C
cable
TR-004
TR-004U • Uses a USB 3.2 Gen 1 Type-C
interface
• Supports SATA drives
• USB 3.2 Gen 1 Type-A to
Type-C cable
• RAIL-B02
TL-D800C • Uses a USB 3.2 Gen 2 Type-C
interface
• Supports SATA drives
USB 3.2 Gen 2 Type-A to Type-C
cable
TL-R1200C-RP • Uses a USB 3.2 Gen 2 Type-C
interface
• Supports SATA drives
• USB 3.2 Gen 2 Type-A to
Type-C cable
• RAIL-B02
To connect the device to USB expansion units, USB Type-A to USB Type-C cables or USB Type-C to USB
Type-C cables are required.
1. Connect the expansion unit to the switch.
a. Connect the USB cable to the USB Type-C port on the expansion unit.
b. Connect the USB cable to a USB 3.2 Gen 1 Type-A port on the switch.
QGD-3014-16PT User Guide
Installation and Configuration 33
2. Power on the expansion units.
3. Verify that the expansion units are recognized by the switch.
a. Log on to QTS as administrator.
b. Go to Main Menu > Storage & Snapshots > Overview > System .
c. Verify that the expansion units are listed.
QTS Installation
Method Description Requirements
Qfinder Pro
installation
(Recommended)
If the switch is connected to your local
area network, you can do the following:
• Locate the switch using Qfinder Pro.
• Complete the steps in the Smart
Installation Guide wizard.
For details, see Installing QTS Using
Qfinder Pro.
• Computer
• Network cable
• Qfinder Pro installer
QGD-3014-16PT User Guide
Installation and Configuration 34
Method Description Requirements
Cloud installation If the switch is connected to the internet,
you can do the following:
• Scan the QR code on the switch.
• Specify the Cloud Key.
• Log into your myQNAPcloud account.
• Use myQNAPcloud Link to remotely
access your switch.
• Complete the steps in the Smart
Installation Guide wizard.
For details, see Installing QTS Using the
Cloud Key.
• Computer or mobile device
• myQNAPcloud account
• Cloud Key
Installing QTS Using Qfinder Pro
Warning
Installing QTS deletes all data on the drives. Back up your data before proceeding.
1. Power on the switch.
2. Connect the switch to your local area network.
Tip
You can connect to the local area network through the host port or through any PoE port.
3. Run Qfinder Pro on a computer that is connected to the same local area network.
Note
To download Qfinder Pro, go to https://www.qnap.com/utilities.
4. Locate the switch in the list and then double-click the name or IP address.
The Smart Installation Guide opens in the default web browser.
5. Click Start Smart Installation Guide.
6. Specify the following information.
•NAS name: Specify a name with 1 to 14 characters. The name supports letters (A to Z, a to z),
numbers (0 to 9), and hyphens (-), but cannot end with a hyphen.
•Password: Specify an administrator password with 1 to 64 characters. The password supports all
ASCII characters.
7. Click Next.
8. Specify the time zone, date, and time.
Tip
QNAP recommends connecting to an NTP server to ensure that the switch follows the
Coordinated Universal Time (UTC) standard.
QGD-3014-16PT User Guide
Installation and Configuration 35
9. Click Next.
10. Select Obtain an IP address automatically (DHCP).
11. Click Next.
12. Select the types of devices that you will use to access shared folders on the switch.
13. Click Next.
14. Review the settings.
15. Click Apply.
A confirmation message appears.
Warning
Clicking Confirm deletes all data on the drive before installing QTS.
16. Click Confirm.
QTS is installed.
Installing QTS Using the Cloud Key
Warning
Installing QTS deletes all data on the drives. Back up your data before proceeding.
1. Power on the switch.
2. Connect the switch to the internet.
3. Go to the QNAP Cloud Installation page using one of the following methods:
• On your computer, go to http://install.qnap.com/.
• Scan the QR code on the switch using a mobile device.
The web page lists all the uninitialized QNAP devices on the local network.
4. Find your switch from the list and then click Initialize.
Note
If your switch is not listed, follow the instructions on the web page to specify the Cloud Key on
the switch.
The installation wizard opens in the default web browser.
5. Create an account or sign in to myQNAPcloud.
Note
You must return to this page to complete the installation after creating an account.
6. Specify the myQNAPcloud device name for the switch.
Note
• The myQNAPcloud device name is used when remotely accessing the switch.
QGD-3014-16PT User Guide
Installation and Configuration 36
• For security purposes, the myQNAPcloud Link remote connection service will be disabled
on your switch after initialization. You can enable it by connecting to QTS through LAN and
then installing myQNAPcloud Link.
7. Click Next.
The Smart Installation Guide opens in the default web browser.
8. Click Start Smart Installation Guide.
9. Specify the following information.
•NAS name: Specify a name with 1 to 14 characters. The name supports letters (A to Z, a to z),
numbers (0 to 9), and hyphens (-), but cannot end with a hyphen.
•Password: Specify an administrator password with 1 to 64 characters. The password supports all
ASCII characters.
10. Click Next.
11. Specify the time zone, date, and time.
Tip
QNAP recommends connecting to an NTP server to ensure that the switch follows the
Coordinated Universal Time (UTC) standard.
12. Click Next.
13. Select Obtain an IP address automatically (DHCP).
14. Click Next.
15. Select the types of devices that you will use to access shared folders on the switch.
16. Click Next.
17. Review the settings.
18. Click Apply.
A confirmation message appears.
Warning
Clicking Confirm deletes all data on the drive before installing QTS.
19. Click Confirm.
QTS is installed.
Switch Management Application Access
You can manage the QGD-3014-16PT switch using the following applications:
Application Description
QuNetSwitch Switch management application for QTS. QuNetSwitch comes
preinstalled in QTS.
QSS Switch management system for QNAP switches. QSS comes
preinstalled on the switch.
For details on how to access these applications, see the following topics:
QGD-3014-16PT User Guide
Installation and Configuration 37
•Accessing QSS with Qfinder Pro
•Accessing QuNetSwitch in QTS
Accessing QSS with Qfinder Pro
Note
You must create a default system volume before using QuNetSwitch.
1. Power on the device.
2. Connect the device to your local area network.
For details, see Connecting the Switch to a Network.
3. Run Qfinder Pro on a computer that is connected to the same local area network.
Note
To download Qfinder Pro, go to https://www.qnap.com/utilities.
4. Enter the switch IP address.
The switch IP address will be displayed as %yourNAS name%- switch.
5. Locate the switch in the list and then double-click the name or IP address.
The QSS login screen appears.
6. Log in to QSS.
The QSS default login details are as follows:
• Username: admin
• Password: admin
The Welcome window appears.
7. Specify the following information.
•NAS name: Specify a name with 1 to 14 characters. The name supports letters (A to Z, a to z),
numbers (0 to 9), and hyphens (-), but cannot end with a hyphen.
•Password: Specify an administrator password with 1 to 64 characters. The password supports all
ASCII characters.
8. Continue with switch management.
Note
For details on switch management, see the QuNetSwitch User Guide.
Accessing QuNetSwitch in QTS
Note
You must create a default system volume before using QuNetSwitch.
For more details, see the QTS User Guide.
1. Power on the device.
2. Log in to QTS.
QGD-3014-16PT User Guide
Installation and Configuration 38
4. Basic Operations
This chapter describes basic switch operations.
Buttons
Power Button
Operation User Action Result
Power on Press the button once. The switch powers on and logs on
to QTS.
Power off Press and hold the button for 1.5
seconds.
The switch powers off and logs out
of QTS.
Force power off Press and hold the button for 5
seconds.
The switch shuts down.
Important
Use this method only
when the switch is
unresponsive.
Switch Reset Button
Operation User Action Result
Reset Press and hold the button for 3
seconds.
The switch resets and all default
settings are restored.
QTS Reset Button
Operation User Action Result
Basic system reset Press and hold the button for 3
seconds.
The following QTS settings are reset to
default:
• System administrator password: admin
• TCP/IP configuration: Obtain IP address
settings automatically via DHCP.
• Disable jumbo frames.
• If port trunking is enabled (multi-LAN
models only), the port trunking mode is
reset to "Active Backup (Failover)".
• System port: 8080 (system service port)
• Security level: Low (Allow all connections)
• LCD panel password: (blank)
• VLAN: Disabled
QGD-3014-16PT User Guide
Basic Operations 40
Operation User Action Result
Advanced system
reset
Press and hold the button for 15
seconds.
The default QTS settings are restored.
Tip
To retrieve old data after an
advanced system reset, recreate
the previous folder structure on the
switch.
LCD Panel
The LCD panel allows you to perform the following operations:
• Restart and power off the device
• Configure or change the LCD panel password
• View and configure network settings
• View information on the system, physical disks, and volumes
Viewing TCP/IP Settings
You can view the following settings for each network adapter on the device.
• IP address
• Subnet mask
• Default gateway
• Primary DNS
• Secondary DNS
1. Press Enter or Select.
The panel displays the switch name and QTS version.
2. Press and hold Enter for two seconds.
The panel displays Main Menu 1. TCP/IP.
3. Press and hold Enter.
The panel displays the IP address of the first network adapter.
4. Press and hold Select to view the next TCP/IP screen.
Repeat this step as necessary.
Configuring TCP/IP Settings
You can configure the following settings for each network adapter on the switch:
• IP address
• Subnet mask
• Default gateway
• Primary DNS
QGD-3014-16PT User Guide
Basic Operations 41
• Secondary DNS
1. Press Enter or Select.
The panel displays the switch name and QTS version.
2. Press and hold Enter for two seconds.
The panel displays Main Menu 1. TCP/IP.
3. Press and hold Enter.
The panel displays the IP address of the first network adapter.
4. Press Select repeatedly until the panel displays Enter Network Settings.
5. Press and hold Enter.
The panel displays the configurable network settings.
6. Press Select and Enter to configure the settings.
Button Usage
Enter • Display a configuration screen.
• Move to the next item on a configuration screen.
Select • Move to the next item on a menu.
• Modify a value on a configuration screen.
Repeat this step if necessary.
Viewing Drive Information
The LCD panel can display the temperature and capacity of each drive installed in the switch.
1. Press Enter or Select.
The panel displays the switch name and the QTS version.
2. Press and hold Enter for two seconds.
The panel displays Main Menu 1. TCP/IP.
3. Press Enter repeatedly until the panel displays Main Menu 2. Physical disk.
4. Press and hold Enter.
The panel displays the temperature and capacity of the drive in bay 1.
5. Press and hold Select.
Repeat this step as necessary.
The panel displays the temperature and capacity of the next drive.
Viewing System Information
The LCD panel can display the CPU temperature, system temperature, and system fan speed.
1. Press Enter or Select.
The panel displays the switch name and QTS version.
2. Press and hold Enter for two seconds.
The panel displays Main Menu 1. TCP/IP.
3. Press Enter repeatedly until the panel displays Main Menu 4. System.
QGD-3014-16PT User Guide
Basic Operations 42
4. Press and hold Enter.
The panel displays the CPU and system temperature.
5. Press and hold Select.
The panel displays the system fan speed.
Powering Off the Switch
1. Press Enter or Select.
The panel displays the switch name and QTS version.
2. Press and hold Enter for two seconds.
The panel displays Main Menu 1. TCP/IP.
3. Press Enter repeatedly until the panel displays Main Menu 5. Shut down.
4. Press and hold Enter.
The switch powers off.
Restarting the Switch
1. Press Enter or Select.
The panel displays the switch name and QTS version.
2. Press and hold Enter for two seconds.
The panel displays Main Menu 1. TCP/IP.
3. Press Enter repeatedly until the panel displays Main Menu 6. Reboot.
4. Press and hold Enter.
The switch restarts.
Changing the LCD Password
Specifying a password for the LCD panel prevents unauthorized access.
1. Press Enter or Select.
The panel displays the switch name and QTS version.
2. Press and hold Enter for two seconds.
The panel displays Main Menu 1. TCP/IP.
3. Press Enter repeatedly until the panel displays Main Menu 7. Password.
4. Press and hold Enter.
The Change Password screen appears.
5. Select Yes by pressing and holding Enter.
The New Password screen appears.
6. Press Select and Enter to specify a new password.
• Specify a password.
• Length: 1-8 characters
• Valid characters: 0-9
QGD-3014-16PT User Guide
Basic Operations 43
• To delete a password, leave the password field blank.
Button Usage
Enter Move to the next item in the New Password screen.
Select Change a number in the New Password and Verify Password
screens.
7. Press Enter.
The switch saves the password.
LCD Error Messages
System Message Description
Sys. Fan Failed System fan has failed.
Sys. Overheat System has overheated.
HDD Overheat Drive has overheated.
CPU Overheat CPU has overheated.
Network Lost LAN 1 and LAN 2 disconnected in failover or load-
balancing mode.
LAN [number] Lost LAN [number] has disconnected.
HDD Failure Drive has failed.
Vol [number] Full Volume is full.
HDD Ejected Drive has ejected.
Vol [number] Degraded Volume [number] is in degrade mode.
Vol [number] Unmounted Volume [number] has unmounted.
Vol [number] Inactive Volume [number] is inactive.
LEDs
LEDs indicate the system status and related information when the device is powered on. The following LED
information applies only when the drive is correctly installed and when the device is connected to the
network or to a host.
For details on the location of the LEDs, see Components.
LED Status Description
Host status Green The host system is ready.
Flashes green every 1.0 sec The host system is starting up.
Red A fatal host system error occurred.
Off The host system is powered off.
Switch status Green The switch is ready.
Flashes green every 1.0 sec The switch is starting up.
Red A fatal switch system error occurred.
Off The switch system is powered off.
PoE Green The PoE status is normal.
Red A fatal PoE error occurred.
QGD-3014-16PT User Guide
Basic Operations 44
LED Status Description
Fan Green The fan status is normal.
Red A fatal fan error occurred.
PoE port speed Flashes green every 1.0 sec The link speed is operating at 1 Gbps.
Flashes amber every 1.0 sec The link speed is operating at 10/100 Mbps.
Off No link was detected.
PoE port
activity/link
Green The switch is connected to a power device.
Amber A power device error occurred.
Off No power device was detected.
Combo port
speed
Flashes green every 1.0 sec The link speed is operating at 1 Gbps.
Flashes amber every 1.0 sec The link speed is operating at 10/100 Mbps.
Off No link was detected.
Combo Port
activity/link
Flashes amber every 1.0 sec Data is being transferred.
Audio Alert
Duration Frequency Description
Short beep (0.5 seconds) 1 • The switch is starting up.
• When the reset button is pressed for 3 seconds,
the switch resets configuration.
• When the reset button is pressed for 10
seconds, the switch resets configuration and
reboots.
• The operating system was updated.
• The switch is starting USB One-Touch Copy.
2 The USB device has been removed (USB One
Touch copy button).
3 Cannot detect installed disk.
QGD-3014-16PT User Guide
Basic Operations 45
Duration Frequency Description
Long beep (1.5 seconds) 3 (every 5 minutes) • A power error occurred.
• The system fan is not functioning.
• The fan module has been removed.
• The switch data cannot be copied to the external
storage device connected to the front USB port.
2 • The disk volume is about to reach its full
capacity.
• The disk volume has reached its full capacity.
• The USB device is being removed (USB one-
touch copy button).
• A volume status error occurred.
• A drive is plugged in or out.
1 • The switch was powered off by force shutdown
(hardware shutdown).
• The switch was powered on successfully and is
ready.
Long beep (5 seconds) 1 QTS is restarting.
QGD-3014-16PT User Guide
Basic Operations 46
5. Troubleshooting
This chapter describes basic troubleshooting information.
Hot-Swapping Failed Drives
RAID Type Number of Disks Situation
RAID 1 2 One member drive fails
RAID 5 ≥ 3 One member drive fails
RAID 6 ≥ 4 One or two member drives fail
RAID 10 ≥ 4 (Must be an even number) One or two member drives in two different pairs fail.
RAID 50 ≥ 6 One disk per subgroup fails.
RAID 60 ≥ 8 Two disks per subgroup fail.
1. Log on to QTS.
2. Go to Main Menu > Storage & Snapshots > Storage > Disks/VJBOD .
3. Locate the failed drive.
4. Prepare a new hard drive with a capacity that is the same as or larger than the failed hard drive.
5. Remove the failed drive from the device.
6. Wait for 20 seconds or until the device beeps twice.
7. Remove the failed drive from the drive tray.
8. Insert the new drive into the drive tray.
9. Install the new drive.
The switch beeps twice.
10. Go to Main Menu > Storage & Snapshots > Storage Space .
11. Locate the volume that contains the new drive and then verify that the status is Rebuilding.
Recovering Unintentionally Removed Healthy Drives
The switch supports exclusive RAID recovery technology to recover failed RAID disk volumes from
unintentional disconnection or removal of drives. Users can recover an inactive RAID 1, RAID 5, RAID 6,
RAID 10, RAID 50, or RAID 60 volume from degraded mode.
Disk Volume RAID
Recovery
Support
Number of Disks Maximum Number of Removed Drives
Single No 1 N/A
JBOD Yes ≥ 2 N/A
RAID 0 Yes ≥ 2 N/A
RAID 1 Yes 2 1
RAID 5 Yes ≥ 3 1
RAID 6 Yes ≥ 4 2
QGD-3014-16PT User Guide
Troubleshooting 47
Disk Volume RAID
Recovery
Support
Number of Disks Maximum Number of Removed Drives
RAID 10 No ≥ 4 (Must be an even
number)
One or two member drives in two different
pairs fail.
RAID 50 Yes ≥ 6 One disk per subgroup fails.
RAID 60 Yes ≥ 8 Two disks per subgroup fail.
Forcing Qfinder Pro and myQNAPcloud to Locate the Switch
If Qfinder Pro or myQNAPcloud is unable to locate the switch during QTS installation, the drives or data may
be faulty.
1. Power off the switch.
2. Remove all drives.
3. Power on the switch.
4. Locate the switch using Qfinder Pro.
5. Reinsert the drives.
6. Continue with the QTS installation.
Support and Other Resources
QNAP provides the following resources:
Resource URL
Documentation https://download.qnap.com
Compatibility List https://www.qnap.com/compatibility/
NAS Migration Compatibility https://www.qnap.com/en/nas-migration
Expansion Unit Compatibility http://www.qnap.com/go/compatibility-expansion
Service Portal https://service.qnap.com
Product Support Status https://www.qnap.com/product/eol.php
Downloads https://download.qnap.com
Community Forum https://forum.qnap.com
QNAP Accessories Store https://shop.qnap.com/
QGD-3014-16PT User Guide
Troubleshooting 48
6. Glossary
myQNAPcloud
Provides various remote access services such as DDNS and myQNAPcloud Link
myQNAPcloud Link
Enables you to access the NAS over the internet without configuring complex port forwarding settings
Qfinder Pro
QNAP utility that lets you locate and access QNAP NAS devices in your local area network
QSS
QNAP switch management application
QTS
QNAP NAS operating system
QuNetSwitch
QNAP switch management app that runs on the QTS operating system
QGD-3014-16PT User Guide
Glossary 49
7. Notices
This chapter provides information about warranty, disclaimers, licensing, and federal regulations.
Limited Warranty
QNAP offers limited warranty service on our products. Your QNAP-branded hardware product is warranted
against defects in materials and workmanship for a period of one (1) year or more from the date printed on
the invoice. ("Warranty Period"). Please review your statutory rights at www.qnap.com/warranty, which may
be amended from time to time by QNAP in its discretion.
Disclaimer
Information in this document is provided in connection with products of QNAP Systems, Inc. (the "QNAP").
No license, express or implied, by estoppels or otherwise, to any intellectual property rights is granted by this
document. Except as provided in QNAP's terms and conditions of sale for such products, QNAP assumes no
liability whatsoever, and QNAP disclaims any express or implied warranty, relating to sale and/or use of
QNAP products including liability or warranties relating to fitness for a particular purpose, merchantability, or
infringement of any patent, copyright or other intellectual property right.
QNAP products are not intended for use in medical, life saving, life sustaining, critical control or safety
systems, or in nuclear facility applications.
In no event shall QNAP’s liability exceed the price paid for the product from direct, indirect, special,
incidental, or consequential damages resulting from the use of the product, its accompanying software, or its
documentation. QNAP makes no warranty or representation, expressed, implied, or statutory, with respect to
its products or the contents or use of this documentation and all accompanying software, and specifically
disclaims its quality, performance, merchantability, or fitness for any particular purpose. QNAP reserves the
right to revise or update its products, software, or documentation without obligation to notify any individual or
entity.
Back up the system periodically to avoid any potential data loss is recommended. QNAP disclaims any
responsibility of all sorts of data loss or recovery.
Should you return any components of the package of QNAP products such as NAS (Network Attached
Storage) for refund or maintenance, make sure they are carefully packed for shipping. Any form of damages
due to improper packaging will not be compensated.
All the features, functionality, and other product specifications are subject to change without prior notice or
obligation. Information contained herein is subject to change without notice.
Further, the ® or ™ symbols are not used in the text.
GNU Public License
Version 3, 29 June 2007
Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not
allowed.
Preamble
The GNU General Public License is a free, copy left license for software and other kinds of works.
The licenses for most software and other practical works are designed to take away your freedom to share
and change the works. By contrast, the GNU General Public License is intended to guarantee your freedom
to share and change all versions of a program--to make sure it remains free software for all its users. We, the
QGD-3014-16PT User Guide
Notices 50
Free Software Foundation, use the GNU General Public License for most of our software; it applies also to
any other work released this way by its authors. You can apply it to your programs, too.
When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are
designed to make sure that you have the freedom to distribute copies of free software (and charge for them if
you wish), that you receive source code or can get it if you want it, that you can change the software or use
pieces of it in new free programs, and that you know you can do these things.
To protect your rights, we need to prevent others from denying you these rights or asking you to surrender
the rights. Therefore, you have certain responsibilities if you distribute copies of the software, or if you modify
it: responsibilities to respect the freedom of others.
For example, if you distribute copies of such a program, whether gratis or for a fee, you must pass on to the
recipients the same freedoms that you received. You must make sure that they, too, receive or can get the
source code. And you must show them these terms so they know their rights.
Developers that use the GNU GPL protect your rights with two steps: (1) assert copyright on the software,
and (2) offer you this License giving you legal permission to copy, distribute and/or modify it.
For the developers' and authors' protection, the GPL clearly explains that there is no warranty for this free
software. For both users' and authors' sake, the GPL requires that modified versions be marked as changed,
so that their problems will not be attributed erroneously to authors of previous versions.
Some devices are designed to deny users access to install or run modified versions of the software inside
them, although the manufacturer can do so. This is fundamentally incompatible with the aim of protecting
users' freedom to change the software. The systematic pattern of such abuse occurs in the area of products
for individuals to use, which is precisely where it is most unacceptable. Therefore, we have designed this
version of the GPL to prohibit the practice for those products. If such problems arise substantially in other
domains, we stand ready to extend this provision to those domains in future versions of the GPL, as needed
to protect the freedom of users.
Finally, every program is threatened constantly by software patents. States should not allow patents to
restrict development and use of software on general-purpose computers, but in those that do, we wish to
avoid the special danger that patents applied to a free program could make it effectively proprietary. To
prevent this, the GPL assures that patents cannot be used to render the program non-free.
The precise terms and conditions for copying, distribution and modification follow.
Terms and Conditions
1. Definitions.
“This License” refers to version 3 of the GNU General Public License.
“Copyright” also means copyright-like laws that apply to other kinds of works, such as semiconductor
masks.
“The Program” refers to any copyrightable work licensed under this License. Each licensee is
addressed as “you”. “Licensees” and “recipients” may be individuals or organizations.
To “modify” a work means to copy from or adapt all or part of the work in a fashion requiring copyright
permission, other than the making of an exact copy. The resulting work is called a “modified version” of
the earlier work or a work “based on” the earlier work.
A “covered work” means either the unmodified Program or a work based on the Program.
To “propagate” a work means to do anything with it that, without permission, would make you directly or
secondarily liable for infringement under applicable copyright law, except executing it on a computer or
modifying a private copy. Propagation includes copying, distribution (with or without modification),
making available to the public, and in some countries other activities as well.
To “convey” a work means any kind of propagation that enables other parties to make or receive
copies. Mere interaction with a user through a computer network, with no transfer of a copy, is not
conveying.
An interactive user interface displays “Appropriate Legal Notices” to the extent that it includes a
convenient and prominently visible feature that (1) displays an appropriate copyright notice, and (2)
QGD-3014-16PT User Guide
Notices 51
tells the user that there is no warranty for the work (except to the extent that warranties are provided),
that licensees may convey the work under this License, and how to view a copy of this License. If the
interface presents a list of user commands or options, such as a menu, a prominent item in the list
meets this criterion.
2. Source Code.
The “source code” for a work means the preferred form of the work for making modifications to it.
“Object code” means any non-source form of a work.
A “Standard Interface” means an interface that either is an official standard defined by a recognized
standards body, or, in the case of interfaces specified for a particular programming language, one that
is widely used among developers working in that language.
The “System Libraries” of an executable work include anything, other than the work as a whole, that (a)
is included in the normal form of packaging a Major Component, but which is not part of that Major
Component, and (b) serves only to enable use of the work with that Major Component, or to implement
a Standard Interface for which an implementation is available to the public in source code form. A
“Major Component”, in this context, means a major essential component (kernel, window system, and
so on) of the specific operating system (if any) on which the executable work runs, or a compiler used
to produce the work, or an object code interpreter used to run it.
The “Corresponding Source” for a work in object code form means all the source code needed to
generate, install, and (for an executable work) run the object code and to modify the work, including
scripts to control those activities. However, it does not include the work's System Libraries, or general-
purpose tools or generally available free programs which are used unmodified in performing those
activities but which are not part of the work. For example, Corresponding Source includes interface
definition files associated with source files for the work, and the source code for shared libraries and
dynamically linked subprograms that the work is specifically designed to require, such as by intimate
data communication or control flow between those subprograms and other parts of the work.
The Corresponding Source need not include anything that users can regenerate automatically from
other parts of the Corresponding Source.
The Corresponding Source for a work in source code form is that same work.
3. Basic Permissions.
All rights granted under this License are granted for the term of copyright on the Program, and are
irrevocable provided the stated conditions are met. This License explicitly affirms your unlimited
permission to run the unmodified Program. The output from running a covered work is covered by this
License only if the output, given its content, constitutes a covered work. This License acknowledges
your rights of fair use or other equivalent, as provided by copyright law.
You may make, run and propagate covered works that you do not convey, without conditions so long as
your license otherwise remains in force. You may convey covered works to others for the sole purpose
of having them make modifications exclusively for you, or provide you with facilities for running those
works, provided that you comply with the terms of this License in conveying all material for which you
do not control copyright. Those thus making or running the covered works for you must do so
exclusively on your behalf, under your direction and control, on terms that prohibit them from making
any copies of your copyrighted material outside their relationship with you.
Conveying under any other circumstances is permitted solely under the conditions stated below.
Sublicensing is not allowed; section 10 makes it unnecessary.
4. Protecting Users' Legal Rights From Anti-Circumvention Law.
No covered work shall be deemed part of an effective technological measure under any applicable law
fulfilling obligations under article 11 of the WIPO copyright treaty adopted on 20 December 1996, or
similar laws prohibiting or restricting circumvention of such measures.
When you convey a covered work, you waive any legal power to forbid circumvention of technological
measures to the extent such circumvention is effected by exercising rights under this License with
respect to the covered work, and you disclaim any intention to limit operation or modification of the
work as a means of enforcing, against the work's users, your or third parties' legal rights to forbid
circumvention of technological measures.
5. Conveying Verbatim Copies.
QGD-3014-16PT User Guide
Notices 52
You may convey verbatim copies of the Program's source code as you receive it, in any medium,
provided that you conspicuously and appropriately publish on each copy an appropriate copyright
notice; keep intact all notices stating that this License and any non-permissive terms added in accord
with section 7 apply to the code; keep intact all notices of the absence of any warranty; and give all
recipients a copy of this License along with the Program.
You may charge any price or no price for each copy that you convey, and you may offer support or
warranty protection for a fee.
6. Conveying Modified Source Versions.
You may convey a work based on the Program, or the modifications to produce it from the Program, in
the form of source code under the terms of section 4, provided that you also meet all of these
conditions:
a. The work must carry prominent notices stating that you modified it, and giving a relevant date.
b. The work must carry prominent notices stating that it is released under this License and any
conditions added under section 7. This requirement modifies the requirement in section 4 to “keep
intact all notices”.
c. You must license the entire work, as a whole, under this License to anyone who comes into
possession of a copy. This License will therefore apply, along with any applicable section 7
additional terms, to the whole of the work, and all its parts, regardless of how they are packaged.
This License gives no permission to license the work in any other way, but it does not invalidate
such permission if you have separately received it.
d. If the work has interactive user interfaces, each must display Appropriate Legal Notices; however,
if the Program has interactive interfaces that do not display Appropriate Legal Notices, your work
need not make them do so.
A compilation of a covered work with other separate and independent works, which are not by
their nature extensions of the covered work, and which are not combined with it such as to form a
larger program, in or on a volume of a storage or distribution medium, is called an “aggregate” if
the compilation and its resulting copyright are not used to limit the access or legal rights of the
compilation's users beyond what the individual works permit. Inclusion of a covered work in an
aggregate does not cause this License to apply to the other parts of the aggregate.
7. Conveying Non-Source Forms.
You may convey a covered work in object code form under the terms of sections 4 and 5, provided that
you also convey the machine-readable Corresponding Source under the terms of this License, in one of
these ways:
a. Convey the object code in, or embodied in, a physical product (including a physical distribution
medium), accompanied by the Corresponding Source fixed on a durable physical medium
customarily used for software interchange.
b. Convey the object code in, or embodied in, a physical product (including a physical distribution
medium), accompanied by a written offer, valid for at least three years and valid for as long as you
offer spare parts or customer support for that product model, to give anyone who possesses the
object code either (1) a copy of the Corresponding Source for all the software in the product that
is covered by this License, on a durable physical medium customarily used for software
interchange, for a price no more than your reasonable cost of physically performing this conveying
of source, or (2) access to copy the Corresponding Source from a network server at no charge.
c. Convey individual copies of the object code with a copy of the written offer to provide the
Corresponding Source. This alternative is allowed only occasionally and noncommercially, and
only if you received the object code with such an offer, in accord with subsection 6b.
d. Convey the object code by offering access from a designated place (gratis or for a charge), and
offer equivalent access to the Corresponding Source in the same way through the same place at
no further charge. You need not require recipients to copy the Corresponding Source along with
QGD-3014-16PT User Guide
Notices 53
the object code. If the place to copy the object code is a network server, the Corresponding
Source may be on a different server (operated by you or a third party) that supports equivalent
copying facilities, provided you maintain clear directions next to the object code saying where to
find the Corresponding Source. Regardless of what server hosts the Corresponding Source, you
remain obligated to ensure that it is available for as long as needed to satisfy these requirements.
e. Convey the object code using peer-to-peer transmission, provided you inform other peers where
the object code and Corresponding Source of the work are being offered to the general public at
no charge under subsection 6d.
A separable portion of the object code, whose source code is excluded from the Corresponding
Source as a System Library, need not be included in conveying the object code work.
A “User Product” is either (1) a “consumer product”, which means any tangible personal property
which is normally used for personal, family, or household purposes, or (2) anything designed or
sold for incorporation into a dwelling. In determining whether a product is a consumer product,
doubtful cases shall be resolved in favor of coverage. For a particular product received by a
particular user, “normally used” refers to a typical or common use of that class of product,
regardless of the status of the particular user or of the way in which the particular user actually
uses, or expects or is expected to use, the product. A product is a consumer product regardless of
whether the product has substantial commercial, industrial or non-consumer uses, unless such
uses represent the only significant mode of use of the product.
“Installation Information” for a User Product means any methods, procedures, authorization keys,
or other information required to install and execute modified versions of a covered work in that
User Product from a modified version of its Corresponding Source. The information must suffice
to ensure that the continued functioning of the modified object code is in no case prevented or
interfered with solely because modification has been made.
If you convey an object code work under this section in, or with, or specifically for use in, a User
Product, and the conveying occurs as part of a transaction in which the right of possession and
use of the User Product is transferred to the recipient in perpetuity or for a fixed term (regardless
of how the transaction is characterized), the Corresponding Source conveyed under this section
must be accompanied by the Installation Information. But this requirement does not apply if
neither you nor any third party retains the ability to install modified object code on the User
Product (for example, the work has been installed in ROM).
The requirement to provide Installation Information does not include a requirement to continue to
provide support service, warranty, or updates for a work that has been modified or installed by the
recipient, or for the User Product in which it has been modified or installed. Access to a network
may be denied when the modification itself materially and adversely affects the operation of the
network or violates the rules and protocols for communication across the network.
Corresponding Source conveyed, and Installation Information provided, in accord with this section
must be in a format that is publicly documented (and with an implementation available to the
public in source code form), and must require no special password or key for unpacking, reading
or copying.
8. Additional Terms.
“Additional permissions” are terms that supplement the terms of this License by making exceptions
from one or more of its conditions. Additional permissions that are applicable to the entire Program
shall be treated as though they were included in this License, to the extent that they are valid under
applicable law. If additional permissions apply only to part of the Program, that part may be used
separately under those permissions, but the entire Program remains governed by this License without
regard to the additional permissions.
When you convey a copy of a covered work, you may at your option remove any additional permissions
from that copy, or from any part of it. (Additional permissions may be written to require their own
removal in certain cases when you modify the work.) You may place additional permissions on material,
added by you to a covered work, for which you have or can give appropriate copyright permission.
Notwithstanding any other provision of this License, for material you add to a covered work, you may (if
authorized by the copyright holders of that material) supplement the terms of this License with terms:
QGD-3014-16PT User Guide
Notices 54
a. Disclaiming warranty or limiting liability differently from the terms of sections 15 and 16 of this
License; or
b. Requiring preservation of specified reasonable legal notices or author attributions in that material
or in the Appropriate Legal Notices displayed by works containing it; or
c. Prohibiting misrepresentation of the origin of that material, or requiring that modified versions of
such material be marked in reasonable ways as different from the original version; or
d. Limiting the use for publicity purposes of names of licensors or authors of the material; or
e. Declining to grant rights under trademark law for use of some trade names, trademarks, or service
marks; or
f. Requiring indemnification of licensors and authors of that material by anyone who conveys the
material (or modified versions of it) with contractual assumptions of liability to the recipient, for any
liability that these contractual assumptions directly impose on those licensors and authors.
All other non-permissive additional terms are considered “further restrictions” within the meaning
of section 10. If the Program as you received it, or any part of it, contains a notice stating that it is
governed by this License along with a term that is a further restriction, you may remove that term.
If a license document contains a further restriction but permits relicensing or conveying under this
License, you may add to a covered work material governed by the terms of that license document,
provided that the further restriction does not survive such relicensing or conveying.
If you add terms to a covered work in accord with this section, you must place, in the relevant
source files, a statement of the additional terms that apply to those files, or a notice indicating
where to find the applicable terms.
Additional terms, permissive or non-permissive, may be stated in the form of a separately written
license, or stated as exceptions; the above requirements apply either way.
9. Termination.
You may not propagate or modify a covered work except as expressly provided under this License. Any
attempt otherwise to propagate or modify it is void, and will automatically terminate your rights under
this License (including any patent licenses granted under the third paragraph of section 11).
However, if you cease all violation of this License, then your license from a particular copyright holder is
reinstated (a) provisionally, unless and until the copyright holder explicitly and finally terminates your
license, and (b) permanently, if the copyright holder fails to notify you of the violation by some
reasonable means prior to 60 days after the cessation.
Moreover, your license from a particular copyright holder is reinstated permanently if the copyright
holder notifies you of the violation by some reasonable means, this is the first time you have received
notice of violation of this License (for any work) from that copyright holder, and you cure the violation
prior to 30 days after your receipt of the notice.
Termination of your rights under this section does not terminate the licenses of parties who have
received copies or rights from you under this License. If your rights have been terminated and not
permanently reinstated, you do not qualify to receive new licenses for the same material under section
10.
10. Acceptance Not Required for Having Copies.
You are not required to accept this License in order to receive or run a copy of the Program. Ancillary
propagation of a covered work occurring solely as a consequence of using peer-to-peer transmission to
receive a copy likewise does not require acceptance. However, nothing other than this License grants
you permission to propagate or modify any covered work. These actions infringe copyright if you do not
accept this License. Therefore, by modifying or propagating a covered work, you indicate your
acceptance of this License to do so.
11. Automatic Licensing of Downstream Recipients.
Each time you convey a covered work, the recipient automatically receives a license from the original
licensors, to run, modify and propagate that work, subject to this License. You are not responsible for
enforcing compliance by third parties with this License.
QGD-3014-16PT User Guide
Notices 55
An “entity transaction” is a transaction transferring control of an organization, or substantially all assets
of one, or subdividing an organization, or merging organizations. If propagation of a covered work
results from an entity transaction, each party to that transaction who receives a copy of the work also
receives whatever licenses to the work the party's predecessor in interest had or could give under the
previous paragraph, plus a right to possession of the Corresponding Source of the work from the
predecessor in interest, if the predecessor has it or can get it with reasonable efforts.
You may not impose any further restrictions on the exercise of the rights granted or affirmed under this
License. For example, you may not impose a license fee, royalty, or other charge for exercise of rights
granted under this License, and you may not initiate litigation (including a cross-claim or counterclaim in
a lawsuit) alleging that any patent claim is infringed by making, using, selling, offering for sale, or
importing the Program or any portion of it.
12. Patents.
A “contributor” is a copyright holder who authorizes use under this License of the Program or a work on
which the Program is based. The work thus licensed is called the contributor's “contributor version”.
A contributor's “essential patent claims” are all patent claims owned or controlled by the contributor,
whether already acquired or hereafter acquired, that would be infringed by some manner, permitted by
this License, of making, using, or selling its contributor version, but do not include claims that would be
infringed only as a consequence of further modification of the contributor version. For purposes of this
definition, “control” includes the right to grant patent sublicenses in a manner consistent with the
requirements of this License.
Each contributor grants you a non-exclusive, worldwide, royalty-free patent license under the
contributor's essential patent claims, to make, use, sell, offer for sale, import and otherwise run, modify
and propagate the contents of its contributor version.
In the following three paragraphs, a “patent license” is any express agreement or commitment, however
denominated, not to enforce a patent (such as an express permission to practice a patent or covenant
not to sue for patent infringement). To “grant” such a patent license to a party means to make such an
agreement or commitment not to enforce a patent against the party.
If you convey a covered work, knowingly relying on a patent license, and the Corresponding Source of
the work is not available for anyone to copy, free of charge and under the terms of this License, through
a publicly available network server or other readily accessible means, then you must either (1) cause
the Corresponding Source to be so available, or (2) arrange to deprive yourself of the benefit of the
patent license for this particular work, or (3) arrange, in a manner consistent with the requirements of
this License, to extend the patent license to downstream recipients. “Knowingly relying” means you
have actual knowledge that, but for the patent license, your conveying the covered work in a country, or
your recipient's use of the covered work in a country, would infringe one or more identifiable patents in
that country that you have reason to believe are valid.
If, pursuant to or in connection with a single transaction or arrangement, you convey, or propagate by
procuring conveyance of, a covered work, and grant a patent license to some of the parties receiving
the covered work authorizing them to use, propagate, modify or convey a specific copy of the covered
work, then the patent license you grant is automatically extended to all recipients of the covered work
and works based on it.
A patent license is “discriminatory” if it does not include within the scope of its coverage, prohibits the
exercise of, or is conditioned on the non-exercise of one or more of the rights that are specifically
granted under this License. You may not convey a covered work if you are a party to an arrangement
with a third party that is in the business of distributing software, under which you make payment to the
third party based on the extent of your activity of conveying the work, and under which the third party
grants, to any of the parties who would receive the covered work from you, a discriminatory patent
license (a) in connection with copies of the covered work conveyed by you (or copies made from those
copies), or (b) primarily for and in connection with specific products or compilations that contain the
covered work, unless you entered into that arrangement, or that patent license was granted, prior to 28
March 2007.
Nothing in this License shall be construed as excluding or limiting any implied license or other defenses
to infringement that may otherwise be available to you under applicable patent law.
13. No Surrender of Others' Freedom.
QGD-3014-16PT User Guide
Notices 56
If conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the
conditions of this License, they do not excuse you from the conditions of this License. If you cannot
convey a covered work so as to satisfy simultaneously your obligations under this License and any
other pertinent obligations, then as a consequence you may not convey it at all. For example, if you
agree to terms that obligate you to collect a royalty for further conveying from those to whom you
convey the Program, the only way you could satisfy both those terms and this License would be to
refrain entirely from conveying the Program.
14. Use with the GNU Affero General Public License.
Notwithstanding any other provision of this License, you have permission to link or combine any
covered work with a work licensed under version 3 of the GNU Affero General Public License into a
single combined work, and to convey the resulting work. The terms of this License will continue to apply
to the part which is the covered work, but the special requirements of the GNU Affero General Public
License, section 13, concerning interaction through a network will apply to the combination as such.
15. Revised Versions of this License.
The Free Software Foundation may publish revised and/or new versions of the GNU General Public
License from time to time. Such new versions will be similar in spirit to the present version, but may
differ in detail to address new problems or concerns.
Each version is given a distinguishing version number. If the Program specifies that a certain numbered
version of the GNU General Public License “or any later version” applies to it, you have the option of
following the terms and conditions either of that numbered version or of any later version published by
the Free Software Foundation. If the Program does not specify a version number of the GNU General
Public License, you may choose any version ever published by the Free Software Foundation.
If the Program specifies that a proxy can decide which future versions of the GNU General Public
License can be used, that proxy's public statement of acceptance of a version permanently authorizes
you to choose that version for the Program.
Later license versions may give you additional or different permissions. However, no additional
obligations are imposed on any author or copyright holder as a result of your choosing to follow a later
version.
16. Disclaimer of Warranty.
THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE
LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR
OTHER PARTIES PROVIDE THE PROGRAM “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER
EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO
THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM
PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR
CORRECTION.
17. Limitation of Liability.
IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY
COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MODIFIES AND/OR CONVEYS THE
PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY
GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE
OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR
DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES
OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF
SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES.
18. Interpretation of Sections 16 and 17.
If the disclaimer of warranty and limitation of liability provided above cannot be given local legal effect
according to their terms, reviewing courts shall apply local law that most closely approximates an
absolute waiver of all civil liability in connection with the Program, unless a warranty or assumption of
liability accompanies a copy of the Program in return for a fee.
QGD-3014-16PT User Guide
Notices 57
END OF TERMS AND CONDITIONS
CE Notice
This QNAP NAS complies with CE Compliance Class A.
FCC Notice
FCC Class A Notice
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired
operation.
Note
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio
frequency energy, and if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference, in which case the user will be
required to correct the interference at his own expense.
Important
Any modifications made to this device that are not approved by QNAP Systems, Inc. may
void the authority granted to the user by the FCC to operate this equipment.
VCCI Notice
この装置は、クラス A 情報技術装置です。この装置を家庭環境で使用すると電波
妨害を引き起こすことがあります。この場合には使用者が適切な対策を講ずるよう要求されることがありま
す。
VCCI–A
QGD-3014-16PT User Guide
Notices 58
BSMI Notice
警告使用者：這是甲類的資訊產品，在居住的環境中使用時，可能會造成射頻干擾，在
這種情況下，使用者會被要求採取某些適當的對策。
SJ/T 11364-2006
本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符合中国
RoHS 标准规定的限量要求。
本产品上会附有”环境友好使用期限”的标签，此期限是估算这些物质”不会有泄漏或突变”的年限。本产品
可能包含有较短的环境友好使用期限的可替换元件，像是电池或灯管，这些元件将会单独标示出来。
部件名称 有毒有害物质或元素
铅
(Pb)
汞
(Hg)
镉
(Cd)
六价铬
(CR(VI))
多溴联苯
(PBB)
多溴二苯醚
(PBDE)
壳体 0 0 0 0 0 0
显示 0 0 0 0 0 0
印刷电路板 0 0 0 0 0 0
金属螺帽 0 0 0 0 0 0
电缆组装 0 0 0 0 0 0
风扇组装 0 0 0 0 0 0
电力供应组装 0 0 0 0 0 0
电池 0 0 0 0 0 0
O: 表示该有毒有害物质在该部件所有物质材料中的含量均在 SJ/T11363-2006 标准规定的限量要求以下。
X: 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T11363-2006 标准规定的限量要求。
QGD-3014-16PT User Guide
Notices 59