Table of Contents
- Table of Contents
- Safety Warnings
- Chapter 1. Product Overview
- Chapter 2. Basic Operations
- Chapter 3. Upgrade Memory on QNAP Turbo NAS (RAM Module Installation)
- Chapter 4. Expansion Card Installation
- Chapter 5. Install M.2 SSDs
- Chapter 6. Install and Hot-swap Drives
- Chapter 7. Using the LCD Panel
- Technical Support
- GNU GENERAL PUBLIC LICENSE
QNAP TS-1685 User Manual
Displayed below is the user manual for TS-1685 by QNAP which is a product in the NAS & Storage Servers category. This manual has pages.
Related Manuals
2017-05-23
QNAP Turbo NAS
TS-1685 Hardwar e User Manual
© 2017. QNAP Systems, Inc. All Rights Reserved.
2
Thank you for choosing QNAP products! This user manual provides description of the
hardware of the T urbo NAS and relevant guideline of certain functions. Please read carefully
and strictly adhere to the instructions of the manual.
This user manual is applicable to the following Turbo NAS models:
TS-1685
NOTE
• The “Turbo NAS” is hereafter referred to as “NAS”.
• The product you purchased may not support certain functions dedicated to specific
models.
• All features, functionality, and other product specifications are subject to change
without prior notice or obligation.
• Information presented is subject to change without notice.
• No part of this publication may be reproduced, stored in a retrieval system, or
transmitted, in any form or by any means, mechanical, electronic, photocopying,
recording, or otherwise, without prior written permission of QN AP Systems, Inc.
• QNAP and the QNAP logo are registered trademarks of QNAP Systems, Inc. Other
products and comp any names ment ioned herein may be the trademarks of their
respective companies.
3
DISCLAIMER
In no eve nt shall QNAP S ystems, Inc. (QNA P) liability exceed the price pai d for the product
from direct, indirect, special, incidental, or consequential damages resulting from the use
of the product, its accompanying software, or its documentation. QNAP makes no warranty
or representation, expressed, implied, or statutory, with respect to its products or the
contents or use of this documentation and all accompanying software, and specifically
disclaims its quality, performance, merchantability, or fitness for any particular purpose.
QNAP reserves the right to revise or update its products, software, or documentation
without obligation to notify any individua l o r e ntity.
Note:
Back up your system periodically to avoid any potential data loss. QNAP disclaims any
responsibility of all sorts of data loss or recovery.
Should you return any components of the NAS package for refund or maintenance,
make sure they are carefully packed for shipping. Any form of damages due to
improper packaging will not be compensated.
4
Regulatory Notice
FCC Class B Notice
The TS-1685 complies with Part 15 of the FCC Rules. Oper a ti on i s su bje ct to the following
two conditions:
1. This device may not cause har mfu l interference.
2. This device must accept any interference received, including interference that may
cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interferen c e in a r e sidential in stallation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause h armful interf eren c e to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenn a.
• Increase the separation betw een the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/television technician for help.
Modifications: Any modifications made to this device that are not approved by QNAP
Systems, Inc . may void the authority granted to the user by the FCC to ope rate t his
equipment.
5
CE NOTICE
The TS-1685 series complies with CE compliance classes B.
RESTRICTED ACCESS LOCATION
This equipment must be only located where both of the following apply:
Only authorized and knowledgeable personnel can access the equipment
Access to the equipment is restricted through the use of lock and key or other means of
security and this access is controlled by those in charge of the location.
6
Symbols in this document
Warning
This icon indicates the instructions must be strictly followed. Failure
to do so could result in injury to human body or death.
Caution
This icon indicates the action may lead to disk clear ance or loss OR
failure to follow the instructions could result in data damage, disk
damage, or product damage.
7
Table of Contents
Table of Contents ............................................................................................... 7
Safety Warnings ................................................................................................. 8
Chapter 1. Product Overview ........................................................................... 9
1.1 HARDWARE SPECIFICATION ............................................................................ 9
1.2 ORDERING INFORMATION ............................................................................ 10
1.3 COMPONENTS .......................................................................................... 11
Chapter 2. Basic Operations .......................................................................... 14
2.1 POWER BUTTON ....................................................................................... 14
2.2 RESET BUTTON ........................................................................................ 14
2.3 USB ONE TOUCH COPY .............................................................................. 15
2.4 LED .................................................................................................... 16
2.5 BEEP ALARM ........................................................................................... 18
Chapter 3. Upgrade Memory on QNAP Turbo NAS (RAM Module Installation) 19
Chapter 4. Expansion Card Installation ......................................................... 24
Chapter 5. Install M.2 SSDs ........................................................................... 26
5.1 M.2 SSD HEAT SINK INSTALLATION ............................................................... 26
5.2 M.2 SSD INSTALLATION ............................................................................. 27
Chapter 6. Install and Hot-swap Drives ......................................................... 29
6.1 DRIVE BAY NUMBERING ................................................................................... 29
6.2 INSTALLING DRIVES ....................................................................................... 29
6.3 RAID RECOVERY - HOT-SWAPPING DRIVES ........................................................... 34
6.4 RAID RECOVERY - ACCIDENTAL REMOVAL OF A HEALTHY DRIVE .................................... 35
Chapter 7. Using the LCD Panel ..................................................................... 37
Technical Support ............................................................................................ 42
GNU GENERAL PUBLIC LICENSE ....................................................................... 43
8
Safety Warnings
1. The NAS can operate normally in temperatures of 0ºC - 40ºC (32ºF - 104ºF) and
relative humidity of 5% - 95%. Please make sure the environment is well-ventilated.
2. The power cord and devices connected to the NAS must provide correct supply voltage
(100W, 90–264V).
3. Do not place the NAS in direct sunlight or near chemicals. Make sure the temperature
and humidity of the environment are in optimized level.
4. Unplug the power cor d and all connected cabl es before cleaning. Wi pe the NAS with a
dry towel. Do not use chemical or aerosol to clean the NAS.
5. Do not place any objects on the NAS for the server’s normal operation and to avoid
overheat.
6. Use the flat head screws in the product package to lock the hard disks in the NAS when
installing hard disks for proper operation.
7. Do not place the NAS near any liquid.
8. Do not place the NAS on any uneven surface to avoid falling off and damage.
9. Make sure the voltage is correct in the location where the NAS is installed. Contact the
distributor or the local power supply company for the information.
10. Do not place any object on the power cord.
11. Do not attempt to repair the NAS in any occasions. Improper disassembly of the
product may expose the users to electric shock or other risks. For any enquiries,
please contact the distributor.
12. The NAS should only be installed in the server room and maintained by the authorized
server manager or IT administrator. The server room is locked by key or keycard
access and only certified staff is allowed to enter the server room.
Warning:
Danger of explosion if battery is incorrectly replaced. Replace only with the same or
equivalent type recommended by the manufact urer. Dispose of used batteries
according to the manufacturer’s instructions.
Do NOT touch the fan inside the system to avoid serious injuries.
9
Chapter 1. Product Overview
Caution: Any unauthorized modifications performed on QNAP products will result in
the warrant y being voided. QNAP is not responsible for any form of damage or loss of data
caused by such modifications. Unauthorized modifications include, but are not limited to,
changes made to the default system firmware, installation of unofficial third pa rty
applications, and changes to the hardware performed by unauthorized technicians.
1.1 Hardware Specification
TS-1685
CPU Intel® Xeon® Processor D-1521 quad-core 2.4 GHz
Intel® Xeon® Processor D-1531 6-core 2.2 GHz
System memory
16GB non-ECC RAM ( 8GB UDIMM*2)
32GB non-ECC RAM (16GB UDIMM*2)
64GB non-ECC RAM (16GB UDIMM*4)
64GB ECC RAM (16GB RDIMM*4)
128GB ECC RAM (32GB RDIMM*4)
Flash memory 512 MB (USB DOM)
CPU replaceable No
Memory replaceable Yes
Memory slots 4 x Long-DIMM slot s
3.5" drive slots 12 x SATA 6 Gb/s (3.5-inch HDD, 2.5 -inch HDD& SSD)
2.5" drive slots 4 x SATA 6 Gb/s (2.5-inch SSD)
M.2 SSD slots 6 x M.2 2242/2260/2280/22110 SATA 6 Gb/s
PCIe slots
3:
Slot 1: PCIe Gen.3 x8
Slot 2: PCIe Gen.2 x4
Slot 3: PCIe Gen.3 x8
10 GbE LAN ports 2 x 10GBASE-T
GbE LAN ports 4
LED panel Mono-LCD display with backlight
Enter and Select buttons for configuration
USB ports Front: 1 x USB 3.0 port
Rear: 2 x USB 3.0 port
Audio outputs 1 x built-in speak er
10
1 x 3.5mm Line-out jack
Note: Only one of the
above audio output ports can work at a time.
If a speaker is connected, the sound will output through the
speaker.
LED indicators Status, USB One Touch Copy, HDD 1-12, SSD 1-4, M.2 SSD 1-6
Buttons Power, USB One Touch Copy, Reset
IR sensor QNAP RM-IR004 remote control (MCE compatible)
Security Kensington security slot
Form factor Tower
Power Supply 100-240V~, 3-1.5A, 60-50Hz, 250W PSU
100-240V~, 3-1.5A, 60-50Hz, 550W PSU
System fans 3 x 9.2cm system fan (12V DC)
CPU fans 2 x 9cm fan
1.2 Ordering Information
NAS SKUs
TS-1685-D1521-16G Intel® Xeon® Processor D-1521, 16GB non-ECC RAM
(8GB UDIMM*2), 250W PSU
TS-1685-D1521-32G Intel® Xeon® Processor D-1521, 32GB non-ECC RAM
(16GB UDIMM*2), 250W PSU
TS-1685-D1521-32G-550W Intel® Xeon® Processor D-1521, 32GB non-ECC RAM
(16GB UDIMM*2), 550W PSU
TS-1685-D1531-32G Intel® Xeon® Processor D-1531, 32GB non-ECC RAM
(16GB UDIMM*2), 250W PSU
TS-1685-D1531-64G Intel® Xeon® Processor D-1531, 64GB non-ECC RAM
(16GB UDIMM*4), 250W PSU
TS-1685-D1531-64GR Intel® Xeon® Processor D-1531, 64GB ECC RAM (16GB
RDIMM*4), 250W PSU
TS-1685-D1531-128GR Intel® X eon® Processor D-
1531, 128GB ECC RAM (32GB
RDIMM*4), 250W PSU
TS-1685-D1531-64GR-550W Intel® Xeon® Processor D-1531, 64GB ECC RAM (16GB
RDIMM*4), 550W PSU
TS-1685-D1531-128GR-550W Intel® X eon® Processor D-
1531, 128GB ECC RAM (32GB
RDIMM*4), 550W PSU
11
1.3 Components
Front View
No. Component
1 LCD pane l
2 Enter button
3 Select button
4 IR sensor
5 Power LED (adjustable bri ghtness)
6 Power button
7 Statu s LED
8 USB One-touch Copy butto n
9 USB 3.0 One-touch Copy port
10 M.2 SSD LEDs
11 SSD LEDs
12 HDD LEDs
12
Back View
No. Component
1 System fans 1 -3
2 Power input
3 Speaker
4 Power switch
5 PCIe slot 1 (full height)
6 PCIe slot 2 (low profile)
7 PCIe slot 3 (low profile)
8 3.5 mm speaker jack
9 Gigabit ports
10 10 GbE 10GBASE-T port
11 USB 3.0 ports
12 Console port
13 Reset button
14 Kensington security slot
13
Side View
No. Component
1 PCIe slot 2 socket (low profile)
2 PCIe slot 3 socket (low profile)
3 M.2 SSD slots
4 Memory slots
5 CPU fans
14
Chapter 2. Basic Operations
2.1 Power button
Power button: Press to turn on or turn off.
System Power button
(Turn on)
Power button
(Hardware turn
off)
Power button
(Force turn off)
All models Press once 1.5 sec 5 sec
2.2 Reset button
Reset button: Press to reset the system settings.
System Basic system reset
(1 beep)
Advanced system reset
(2 beeps)
All models 3 sec 10 sec
Basic system reset (3 sec)
Press the reset button for 3 seconds, a beep sound will be heard. The following settings are
reset to default:
System administration passw ord: admin
TCP/IP configuration: Obtain the IP address settings automatical ly v ia DHC P
TCP/IP configuration: Disable Jumbo Frame
TCP/IP configuration: If port trunking is enabled (dual LAN models only), the port
trunking mode will be reset to “Active Ba ckup (Failover)”.
System Port: 8080 (system service port)
Security Level: Low (Allow all connections)
LCD panel password: (blank)
VLAN will be disabled.
Service b inding: A ll the NAS servic e s run on all available n e twork interfaces.
Advanced system reset (10 sec)
Press the reset button for 10 seconds; you will hear two beeps at the third and the tenth
seconds. The NAS will reset all the system settings to default as it does by web-based
system reset in “Control Panel” > “System Settings” > “Backup / Restore” > “Restore to
Factory Default” except all the data are reserved. The settings such as the users, user
groups, and the network share folders previously created will be cleared. T o retrieve the old
15
data after the advanced system reset, crea te the same network share folders on the NAS
and the data will be accessible again.
2.3 USB One Touch Copy
System Number of seconds (press the one touch copy button
to trigger data copy)
All NAS mod e ls 0.5 sec
Data Copy by the Front USB Port
The NAS supports instant data copy backup from the external USB device to the NAS or the
other w a y r o und b y t he fr on t one t ouc h co p y b utto n. To use thi s func ti on, fo ll o w the s tep s
below:
1. Make sure a drive is installed and formatted on the NAS. The default network share
Qusb or Usb is created.
2. Turn on the NAS.
3. Log into QTS as an administrator.
4. Go to “Main Menu” > “Backup Station” > ”USB One Touch Copy”.
5. Under One touch backup fo r ext ernal device, select USB One Touch Copy.
6. Configure the behavior of USB One Touch Copy.
7. Connect the USB sto rage device to the front USB port of the NAS.
8. Press the Cop y b utto n. The U SB LED wi ll fla sh. The da ta will be copied to or from the
USB device according to the NAS settings.
Note:
This feature adopts incremental backup. After the first time data backup, the NAS only
copies the changed files since the last backup.
This feature is only available on certain NAS models. Please refer to the product
specification table for details at www.qnap.com.
16
2.4 LED
The LED indicators of the NAS indicate the system status and information. When the NAS is
turned on, check the following items to make sure the system status is normal. Note that
the follo wing LED information is applicable only wh e n users have properly installed the
drive, and connected the NAS to the network and the power supply.
LED LED Status Description
System Status
Flashes green and
red alternately
every 0.5 sec
1. The hard drive on the NAS is being
formatted.
2. The NAS is being initialized.
3. The system firmware is being
updated.
4. RAID rebuilding is in process.
5. Online RAID capacity expansion is in
process.
6. Online RAID level migration is in process.
Red
1. The drive is invalid.
2. The disk volume has reached its full
capacity.
3. The disk volume is going to be full.
4. The system fan is out of function.
5. An error occurs when accessing
(read/write) the disk data.
6. A bad sector is detected on the drive.
7. The NAS is in degraded read-only mode
(2 member drives fail in a RAID 5 or RAID
6 configura t i o n, the di sk da ta can still be
read).
8. Hardware self-test error.
Flashes red every
0.5 sec
The NAS is in degraded mode (one member
drive fails in RAID 1, RAID 5 or RAID 6
configuration).
Flashes green
every 0.5 sec
1. The NAS is st a rting up.
2. The NAS is not configured.
3. A hard disk drive is not formatted.
Green The NAS is ready.
Deep flashes of
orange The NAS is in sleep mode.
17
Off All the drives on the NAS are in standby
mode.
LAN Orange
The disk data is being accessed from the
network and a read/write error occurs
during the process.
Flashes orange The NAS is connected to the network.
HDD/SSD/M.2
SSD
Flashes red The NAS is being accessed from the
network.
Red A drive read/write error occurs.
Flashes green The disk data is being accessed.
Green The drive can be accessed.
USB
Flashes blue every
0.5 sec
1. A USB device (connected to the front USB
port) is being detected.
2. A USB device (connected to the front USB
port) is being removed from the NAS.
3. The USB device (connected to the front
USB port of the NAS) is being accessed.
The data is being copied to or from the
external USB device.
Blue A front USB device is detected (after the
device is mounted ).
Off
No USB device detected.
The NAS ha s fini shed co pying the data to o r
from the USB device connected to the front
USB port.
18
2.5 Beep Alarm
The beep alarm can be disabled in “Control Panel” > “System Settings” > “Hardware”.
Beep sound Number of Times Description
Short beep (0.5 s ec) 1
1. The NAS is starting up.
2. The NAS is being shut down
(software shutdown).
3. The user presses the reset button to
reset the NAS.
4. The system firmware has been
updated.
Short beep (0.5 s ec) 3 The NAS data cannot be copied to the
external storage device from the front
USB port.
Long beep (1.5 sec) 3, every 5 min The system fan is out of function.
Long beep (1.5 sec)
2
1. The dis k volume is going to be full.
2. The dis k volume has reac hed its full
capacity.
3. The drives on the NAS are in
degraded mode.
4. The user starts the drive rebuilding
process.
5. A drive is plugged in or out.
1
1. The NAS is turned off by force
shutdown (hardware shutdown).
2. The NAS has been turned on and is
ready.
19
Chapter 3. Upgrade Memory on QNAP Turbo NAS (RAM Module
Installation)
Warning:
The following instructions should only be performed by an authorized or trained
technician.
Strictly adhere to the instructions in this section to install RAM modules in NAS. Failure
to do so could result in property damage, bodily harm or even death.
Before starting, please ensure that you turn off the NAS, disconnect the power
adaptor, network cable(s), and also remove any other device/cable that is attached to
the NAS.
Please ensure that you wear an antistatic wrist strap during the entire process to
prevent electro static discharge. The crocodile clip should be connected to the ground .
When installing more than one memory module, it is recommended to use the same
size and ideally the s ame type/ model in every slot.
QNAP provides RAM modules (optional purchase) for users to upgrade the NAS memory.
Follow the below steps to install an extra memory module on the NAS to upgrade the
memory.
The TS-1685 allows users to upgr ade the memory in their QNAP NAS devices. Ensure t hat
the type of RAM is compatible with the NAS before installi ng.
To determine how much memory is currently in the system:
1. Log into QTS as administ rator.
2. Go to “Control Panel” > “System Setti ngs” > “System Status” to open the System
Status window.
3. To go System Information and check for System memory or Total memory.
20
To install or replace RAM modules:
1. Power off the system by pressing the power button for 1.5 seconds or until the system
beeps once. Wait for all the LEDs on the front of the system to turn off.
2. Disconnect the power cord, network cables, and any other cables attached to the
device.
3. Before opening the NAS, wear an antistatic wrist strap and connect the crocodile clamp
to ground to prevent electrostatic discharge from damaging equipment.
4. Remove the screws on the back of the NAS that are connecting the case cover to the
chassis.
5. Gently remove case cover from case.
21
6. Unlock the RAM slot by pre ssing down on the retention clamps on the side s of the RAM
slot. If replacing RAM, remove existing modu le from socket.
22
7. Install new R A M:
i. Grip the new RAM on the edges to avoid touching contacts or circuitry on the
module.
ii. Line up the notc h on the RAM to the break in the slot. Ensure that first RAM
module is inserted into slot 1 (see below for slot positioning).
iii. Set the stick into the slot and apply equal pressure onto both ends of the stick
until the clamps on the side click and fully lock the RAM in.
23
8. Close the case cover and fasten the screws.
9. Connect the power adaptor and cables to the NAS. Power on NAS.
10. Optiona l: Check that the memory has been correct ly in s talled.
24
Chapter 4. Expansion Card Installation
Warning:
The following instructions should only be performed by an authorized or trained
technician.
Strictly adhere to the instructions in this section to install PCIe add-in card(s) in NAS.
Failure to do so could result in property damage, bodily harm or even death.
The TS-1685 provides 2 low-profile & one full height PCIe expansion slots so that users can
add functionality to their NAS. Refer t o the compatibility list
at http://qnap.com/compatibility.
Follow the steps below to install a PCIe card:
1. Power off the system by pr essing the power button for 1 .5 seconds or until the sys tem
beeps once. Wait for all the LEDs on the front to turn off.
2. Disconnect the power cord, network cables, and any other cables attached to the
device.
3. Before opening the NAS, wear an antistatic wrist strap and connect the crocodile clamp
to ground to prevent electrostatic discharge from damaging equipment.
4. Remove the screws on the back of the NAS that are connecting the case cover to the
chassis.
25
5. Gently remove case cover from case.
6. Remove the screw of the PCIe cover. Remove the cover.
26
7. Hold the network expansion card by grasping the edges. Align the notch on the network
expansion card to the break in the PCIe slot. Fully insert the network expansion card to
the expansion slot.
8. Fasten screw to lock the card in.
9. Close the case cover and fasten the screws.
10. Connect the power adaptor and cables to the NAS.
Chapter 5. Install M.2 SSDs
5.1 M.2 SSD Heat Sink Installation
M.2 cooling modules are packaged with the TS-1685. For reliable operation, it is
recommended that you install the M.2 cooling module on your M.2 SSD. You may also
install t hird party heatsinks on the SSD controller directly.
To install M.2 coo ling module:
1. Disassemble the M.2 co o ling module.
i. Slide the clip away from the tray.
ii. Separate the heatsink from the tray.
2. Peel off the blue protective film from the heatsink.
3. Install the heatsink onto the top of the M.2 SSD.
27
i. Determine the top side of the M.2 SSD by inserting it in the M.2 socket of your
NAS.
ii. Mount the heatsink onto the top of the M.2 SSD.
Note: the figures below display the mounted heatsink locati ons for different sized M.2
SSDs.
4. Place the M.2 SSD/heatsi nk mo d ul e onto the tray.
5. Option a l: Install s pacer in between the M. 2 SSD and the tray if the clip is t o o loose.
6. Insert the clip.
i. Gently squeeze the heatsink and the tray together, and insert the clip at a
35-egree angle.
ii. Slide the clip in .
5.2 M.2 SSD Installation
Note: Do not attempt to bend or remove the orange temperature sensor near the M.2 SS D
socket.
To install M.2 SSD:
1. Power off the system by pressing the power button for 1.5 seconds or until the system
beeps once. Wait for all the LEDs on the front to turn off.
2. Disconnect the power cord, network cables, and any other cables attached to the
device.
3. Before opening the NAS, wear an antistatic wrist strap and connect the crocodile clamp
to ground to prevent electrostatic discharge from damaging equipment.
4. Remove the screws on the back of the NAS that are co nnecting the case cover to the
chassis.
5. Gently remove case cover from case.
6. Remove the fan module.
i. Disconnect the fan cable from the system board.
28
ii. Remove the screw connecting the fan modu le to the chassis.
iii. Press down the clip and remove fan module.
7. Install M.2 SSD.
i. Attach riser screw based on the M.2 SSD size
ii. Insert M.2 SSD into M.2 socket.
iii. Attach screw to riser to hold M.2 SSD in place.
8. Attach the f a n mo d ule.
i. Insert fan module into chassis.
ii. Attach screw to fan module.
iii. Connect fan cable.
9. Close the case cover and fasten the screws.
10. Connect the power adaptor and cables to the NAS.
29
Chapter 6. Install and Hot-swap Drives
The TS-1685 is compati ble with 2.5 -inch/3.5-inch SATA drives. For drive compatibility list,
go to http://www.qnap.com/compatibility.
Caution:
QNAP is not responsible for product damage/malfunction or data loss due to misuse or
improper installation of hard disks.
Note when a drive is installed in a QNAP NAS for the first time, the drive will be
automatically formatted an d all the data on disk will be cleared.
For information on QTS NAS migration, go to docs.qnap.com and check “Migrating from
Old NAS ” section.
6.1 Drive Bay Numbering
Identify the drive position in th e diagram below.
6.2 Installing Drives
To install drives , follow the steps below:
30
1. Remove drive tray from NAS:
a. Push the blue lock switch on the tray down to the unlock position.
b. Push the button below the blue switch to release the lever.
31
c. Pull out tray using lever.
2. Insta lling a drive on the tray.
a. 3.5” HDD:
i. Remove the fastening panels from the sides of a 3.5” drive tray.
ii. Place the drive on the tray so that the holes on the sides of the drive are
aligned with the holes on the sides of the tray.
iii. Attach the fastening pa ne l s to lo ck the dri ve to the tr ay.
Note: Screws may be inserted for increased stability.
32
b. 2.5” HDD:
i. Remove the right fastening panel from the 3.5” drive tray.
ii. Place the 2. 5” drive on the tr ay so that the SAT A connector is facing out and
that three holes on the bottom of the drive are aligned with three holes on
the bottom of the tray.
iii. Attach the screws to lock the drive to the tray.
33
c. SSD:
i. Insert an SSD into an SSD tray so that SATA connector is perfectly aligned
with the opening at end of the tray.
OR
Insert an SSD into a 3.5” drive tray using the same method as in 2b.
34
3. Load tray back into drive bay.
i. Insert the drive tray into th e NAS. Verify tha t the tray is correctly oriented (to p of
HDD facing r i g ht) and fully pushed in.
ii. Close the latch, and lock the switch.
4. To verify that the drive has been correctly installed and recognized by the operating
system, log into QTS as administrator and go to “Storage Manager ” > “Storage” >
“Disks/VJOB” and confirm the disk is in the System Component or NAS Host section.
6.3 RAID Recovery - Hot-Swapping Drives
The QNAP NAS supports hot-swapping driv es. When one drive fails in RAID 1/5, up to two
drives fail in RAID 6/RAID 10*, replacing failed drives with a healthy ones will automatically
trigger QTS to reb uild the RAID. Follow the ste ps belo w to hot-swap drives when drive
failures occur in a RAID configuration. See section 6.2 for detailed instructions on how to
install a new drive.
* One drive each in the RAID 1 pair
Follow instructions below for hot-swapping:
1. Log into QTS as administrator and check the storage pool status in “Storage Manager”
> “Storage” > “Storage Space”. There wil l be a list of all available storage pools.
35
2. If one drive fails in RAID 1/5, up to two drives fail in RAID 6/RAID 10*, the storage pool
status will be labeled as “Degraded” and the Volume/RAID group status should be
labeled as “Warning”.
3. Go to “Storage Manager” > “Storage” > “Disks/VJBOD” to determine which disk needs
to be replaced.
4. Take out bad drive from NAS enclosure and remove the drive from the tray.
5. Install replacement drive onto tray.
Note: the capacity of the new drive must be equal to or greater than the capacity of the
old drive.
7. Insert tray with drive installed into NAS.
Important: Wait for two beeps after remov ing the faulty drive before inserting
replacement drive into NAS. The NAS should also beep twice after replacement drive is
installed.
8. The volume s hould automa tically rebuild. Go to “Storage Manager” > “Storage” >
“Storage Space” to confirm.
6.4 RAID Recov er y - Accidental Removal of a Healthy Drive
The QNAP NAS supports RAID recovery when a healthy drive is unexpectedly removed from
a RAID 1/5/6 during hot-swapping or RAID 0/JBOD configuration in QTS. Note that RAID 10
does not support this feature.
When a healthy drive is unexpectedly removed from a RAID group, the status of the RAID
will change to “Not active”. To recover from an “Not active” status:
1. Re-insert all drives back into the NAS in its original order. This includes any bad drive(s)
that will need to be replaced af ter recovery.
2. Log into QTS as administrator and go to “Storage Manager” > “Storage” > “Storage
Space”.
3. Double click on the affected Storage Pool to open the Storage Pool Management
window.
36
4. In the “Storage Pool Management” wi nd o w, click on the “Manage” button and select
“Recover”.
The process will take about 60 seconds for QTS to complete. When recovery is completed,
the RAID group should be restored to its initial status.
See chart below for RAID status during this process.
Initial
Status
Status After Healthy
Drive is Removed
Status After Drive is
Re-Inserted and Storage
Pool is Recovered
RAID 0/JBOD Ready Not active Ready
RAID 1/5/6 Ready Degraded Rebuilding
RAID 1/5/6 Degraded Not active Degraded
The chart below describes the events of an error when using RAID 5.
RAID 5 (Minimum 3 Disks)
QTS Standard
One drive fails Degrade d m o de (m ay still read
and write).
Degrade d m o de (m ay still read
and write).
One drive fails
and there are bad
sectors found in
the other drive(s)
Read only protect mode (for
immediate data backup & drive
replacement).
RAID crash.
2 drives fail RAID crash. RAID crash.
The chart below describes the events of an error when using RAID 6.
RAID 6 (Minimum 4 Disks)
QTS Standard
One or two drives
drive fail
Degraded mode. (may still rea d
and write).
Degraded mode. (may still rea d
and write).
Two drives fail
and there are bad
sectors found in
the other drive(s)
Read only protect mode (for
immediate data backup & drive
replacement).
RAID crash.
3 drives fail RAID crash. RAID crash.
37
Chapter 7. Using the LCD Panel
The NAS pro vi des a ha ndy LCD panel for u sers to pe rform di sk co nfiguration and view the
system information .
When the NAS has started up, the server name and IP address will be shown.
N A S 5 F 4 D E 3
4 . 3 . 0 ( 2 0 1 7 0 2 1 4 )
After a few seconds, the panel will be automatically turned off. Then you can begin to
configure settings or view system information.
N A S 5 F 4 D E 3
1 6 9 . 2 5 4 . 1 0 0 . 1 0 0
Viewing and configuring system settings
When the name and firmware version of the NAS appear on the panel, press “ENTER” for
two seconds to view the Main Menu, which will automatically disappear if no further actions
are performed in ten secon ds.
There are eight options on the Main Menu:
1. TCP/IP
2. Physical disk
3. Volume
4. System
5. Shut down
6. Reboot
7. Password
8. Back
1. TCP/IP
In TCP/IP, you can see the following information:
LAN1 IP Address
LAN1 Subnet Mask
LAN1 Gateway
LAN 1 PRI. DNS
LAN 1 SEC. DNS
(You can configure the above settings for every interface.)
Enter Network Setti ngs
Network Setti ngs – DHCP
38
Network Setti ngs – Static IP*
Network Setti ngs – BACK
Back to Main Menu
* In Network Settings – Static IP, users can configure the IP address, subnet mask,
gateway, and DNS of LAN 1 and LAN 2.
2. Physical disk
In Physical disk, you can see the following options:
Disk Info
Back to Main Menu
Disk info shows the temperature and the capacity of the drive.
D
i
s
k
:
1
T
e
m
p
:
5
0
°
C
S
i
z
e
:
2
3
2
G
B
3. Volume
This section shows the capacities of volumes and LUNs. You can view the name and
capacity of a volum e/LUN. I f there are mul tiple volumes/L UNs, pre ss "Sele ct" to vi ew
the information of a specific volume/LUN.
D
a
t
a
V
o
l
1
7
5
0
G
B
L
U
N
_
0
7
5
0
G
B
4. System
This section shows the system temperature and the rotation speed of the system fan.
C
P
U
T
e
m
p
:
5
0
°
C
S
y
s
T
e
m
p
:
5
5
°
C
S
y
s
F
a
n
:
8
6
5
R
P
M
5. Shut down
You can use this option to turn off the NAS. Press "SELECT", select "Yes", and then
press "ENTER" to confirm.
6. Reboot
39
You can use this option to restart the NAS. Press "SELECT", select "Yes", and press
"ENTER" to co nf i r m.
7. Password
The default password for the LCD panel is empty. If you want to change the password,
select "Yes" to continue..
C
h
a
n
g
e
P
a
s
s
w
o
r
d
Y
e
s
→
N
o
You can enter up to 8 digits for your password.
Press “SELECT” to increment the digit and press “ENTER” to add a new digit.
After inputting your desired password, press “ENTER”.
When the cursor moves next to "OK", press “ENTER” to confirm the password.
N
e
w
P
a
s
s
w
o
r
d
:
2
3
4
→
O
K
V
e
r
i
f
Y
P
a
s
s
w
o
r
d
:
2
3
4
→
O
K
8. Back
Select this option to return to the main menu.
40
System Messages
When an error occurs, a message will appear on the LCD panel. Press “ENTER” to view the
message and press “ENTER” again to go to the next message.
S
y
s
t
e
m
E
r
r
o
r
!
P
l
s
.
C
h
e
c
k
L
o
g
s
System Message Description
Sys. Fan Failed The system fan fails
Sys. Overheat The system is overheating
HDD Overheat The driv e is overheating
CPU Overheat The CPU is overheating
Network Lost Both LAN 1 and LAN 2 are disconnected in failover or
load-balancing mode
LAN1 Lost LAN 1 is disconnected
LAN2 Lost LAN 2 is disconnected
HDD Fail ur e The drive failed
Vol1 Full The volume is full
HDD Ejected The drive is ejected
RX#3 HDD Ejected A drive ha s been ejec ted from the expansion unit 3.
M.2 SSD Ejected A M.2 SSD has been ejected and may be defective as
hot-plugging is not supported for M.2 drives.
PCIe SSD Ejected A PCIe SSD has been ejected and may be defective as
hot-plugging is not supported for PCIe devices/
Vol1 Degraded The volume is in degraded mode
Vol1 Unmounted The volume is unmounted
Vol1 Nonactivate The volume is not activated
System Startup
S
Y
S
T
E
M
B
O
O
T
I
N
G
>
>
>
There are several phases in the system startup process:
• System Booting: BIOS and hardware initialization, and system booting (no
actions need to be performed)
• Loading Driver: Loading QTS and its drivers (no actions need to be performed)
• Mount Volume: Prepare volumes (no actions need to be performed)
• Starting Service: Starting NAS system services (no actions need to be
41
performed). Note that applications start only after the system finishes booting
For TS-1685, the LCD panel displays additional booting information after you power on the
NAS:
B
I
O
S
X
X
X
X
X
X
X
C
h
e
c
k
i
n
g
M
e
m
o
r
y
• BIOS XXXXXX – XXXXXX is the BIOS version, which can be used for technical
support to help identify and resolve issues.
• Startup phases:
o Checking Memory – The system checks the installed memory.
o P owering up all disks – Power up all disks sequentially.
o Hardware initialization – Initialize additional hardware components, such as
PCIe SSD, Graphic card, Thunderbolt adapter, etc.
o Booting - Boot from the DOM. If the startup stops at this step, the DOM may
be defective. Please seek technical support.
o Starting System – Starting QTS. If the startup stops at this step, the QTS
installation may have encountered problems. Please seek technical support.
• The remaining startup phases are the same as those of other NAS models
43
GNU GENERAL PUBLIC LICENSE
Version 3, 29 June 2007
Copyright © 2007 Free Software Foundation, Inc. <http://fsf.org />
Everyone i s permitted to copy and distribute verbati m copies of this license docu ment, but
changing it is not allowed.
Preamble
The GNU General Public License is a free, co pyleft license for software and other kinds of
works.
The licenses for most software and other practical works are designed to take away your
freedom to share and chan g e th e works. By contrast, the GNU General Public License is
intended to guarantee your freedom to share and change all versions of a program--to
make sure it remains fre e software for all its users. W e, the Free Software F oundation, use
the GNU General Public License for most of our software; it applies also to any other work
released this way by its authors. You can apply it to your programs, t oo.
When we speak of free software, we are referring to freedom, not price. Our General Public
Licenses are designed to make sure that you have the freedom to distribute copies of free
software (and charge for them if you wish), that you receive source code or can get it if you
want it, that you can change the software or use pieces of it in new free programs, and that
you know you can do these things.
To protect your rights, we need to prevent others from denying you these rights or asking
you to surre nder the rights. Therefore, you have certain r e sponsibilities if you distribute
copies of the software, or if you modify it: responsibilities to respect the freedom of others.
For example, if you distribute copies of such a program, whether gratis or for a fee, you
must pass on to the recipients the same freedoms that you received. You must make sure
that they , too, receive or can get the source code. And you must show them these terms so
they know their rights.
Developers that use the GNU GPL protect your rights with two steps: (1) assert copyright
on the so ftware , and (2) offer you this License giving you lega l permission to copy,
distribute and/or modify it.
44
For the developers' and authors' protection, the GPL clearly explains that there is no
warranty for this free software. For both users' and authors' sake, the GPL requires that
modified versions be marked as changed, so that their problems will not be attributed
erroneously to authors of previous versions.
Some devices are designed to deny users access to install or run modified versions of the
software inside them, although the manufacturer can do so. This is fundamentally
incompatible wit h the aim of protecting users' freedom to change the software. The
systematic pattern of such abuse occurs in the area of products for individuals to use, which
is precisely where i t is most unacceptable. The refore, we have designed this versi on of the
GPL to prohibit the practice for those products. If such problems arise substantially in other
domains, we stand ready to extend this provision to those domains in future versions of the
GPL, as needed to protect the freedom of users.
Finally, every program is threatened constantly by software patents. States should not
allow patents to restrict development and use of software on general-purpose computers,
but in those that do, we wish to avoid the special danger that patents applied to a free
program could make it effectively proprietary . To prevent this, the GPL assures that patents
cannot be used to render the program non-free.
The precise terms and conditions for copying, distribution and modification f ollow.
TERMS AND CONDITIONS
0. Definitions.
“This License” refers to version 3 of the GNU General Public License.
“Copyright” also means copyright-like laws that apply to other kinds of works, such as
semiconductor masks.
“The Progr am” refers to any co pyrightable wor k licensed un der this License. Each licensee
is addressed as “you”. “Licensees” and “recipients” may be individuals or organizations.
T o “modify” a work means to copy from or adapt all or part of the work in a fashion requiring
copyright permission, other than the making of an exact copy. The resulting work is called
a “modified version” of the earlier work or a work “based on” the earlier work.
A “covered work” means either the unmodified Program or a work based on the Program.
45
To “propaga te” a wo rk me ans to d o any thing with it t hat, without p ermi ssion, would ma ke
you directly or secondarily liable for infringement under applicable copyright law, except
executing it on a computer or modifying a private copy. Propagation includes copying,
distribution (with or without modification), making available to the public, and in som e
countries other activities a s well.
To “convey” a work means any kind of propagation that enables other parties to make or
receiv e copie s. Mere inter acti on with a user thr ough a co mputer netwo rk, with no tr ansfe r
of a copy, is n o t conveying.
An interactive user interface displays “Appropriate Legal Notices” to the extent that it
includes a convenient and prominently visible feature that (1) displays an appropriate
copyright notice, and (2) tells the user that there is no warranty for the work (except to the
extent that w a r ranties are provided), that licensees may convey the work under this
License, and how to view a copy of this License. If the interface presents a list of user
commands or options, such as a menu, a prominent item in the list meets this criterion.
1. Source Code.
The “source code” for a work means the preferred form of the work for making
modifications to it. “Object code” means any non-source form of a work.
A “Standard Interface” means an interface that either is an official standard defined by a
recognized standards body, or, in the case of interfaces specified for a particular
programming language, one that is widely used among developers working in that
language.
The “System Libraries” of an executable work include anything, other than the work as a
whole, that (a) is included in the normal form of packaging a Major Component, but which
is not part of that Major Component, and (b) serves only to enable use of the work with that
Major Component, or to implement a Standard Interface for which an implementation is
avail able to the public in source code form. A “Major Component”, in this context, means a
major essential component (kernel, window system, and so on) of the specific operating
system (if any) on which the executable work runs, or a compiler used to produce the work,
or an object code interpreter used to run it.
The “Corresponding Source” for a work in object code form means all the source code
needed to generate, install, and (for an executable work) run the object code and to modify
46
the work, including scripts to control those activities. However, it does not include the
work's System Libraries, or general-purpose tools or generally available free programs
which are used unmodified in performing those activities but which are not part of the work.
For example, Corresponding Source includes interface definition files associated with
source files for the work, and the source code for shared libraries and dynamically linked
subprograms that the work is specifically designed to require, such as by intimate data
commun ication or control flow between thos e subprograms and other parts of the work.
The Corresponding Source need not include anything that users can regenerate
automatically from other parts of the Corresponding Source.
The Corresponding Source for a work in source code form is that same work.
2. Basic Permissions.
All rights granted under this License are gr anted for the term of copyright on the P rogram,
and are irrevocable provided the stated conditions are met. This License explicitly affirms
your unlimited permissi on to run the unmodified Program. The output from running a
covered work is covered by this License only if the output, given its content, constitutes a
covered work. This License acknowledges your rights of fair use or other equivalent, as
provided by copyright law.
You may make, run and propagate covered works that you do not convey, without
conditions so long as your license otherwise remains in force. You may convey covered
works to others for the sole purpose of having them make modifications exclusively for you,
or provide you with facilities for running those works, provided that you comply with the
terms of this License in conveying all material for which you do not control copyright. Those
thus making or running the covered works for you must do so exclusively on your b e half,
under your direction and control, on terms that prohibit them from making any copies of
your copyrighted material outside their relationship with you.
Conveying under any other circumstances is permitted solely under the conditions stated
below. Sublicensing is not allowed; section 10 makes it unnecessary.
3. Protecting Users' Legal Rights From Anti-Circumvention Law.
No covered work shall be deemed part of an effective technological measure under any
applicable law fulfilling obligations under article 11 of the WIPO copyright treaty adopted on
20 December 1996, or similar laws prohibiting or restricting circumvention of such
measures.
47
When you convey a covered work, you waive any legal power to forbid circumvention of
technological measures to the extent such circumvention is effected by exercising rights
under this License with respect to the covered work, and you disclaim any intention to limit
operation or modification of the work as a means of enforcing, against the work's users,
your or third parties' legal rights to forbid circumvention of technological measures.
4. Conveying Verbatim Copies.
You may convey verbatim copies of the Program's source code as you receive it, in any
medium, provided that you conspicuously and appropriately publish on each copy an
appropriate copyright notice; keep intact all notices stating that this License and any
non-permissive terms added in accord with section 7 apply to the code; keep intact all
notices of the absence of any warr anty; and give all recipients a copy of this License along
with the Prog ram.
You may charge any price or no price for each copy that you convey, and you may offer
support or warranty protection for a fee.
5. Conveying Modified Source Versions.
You may convey a work based on the Progr am, or the modifications to produce it from the
Program, in the form of source code under the terms of section 4, provided that you also
meet all of these cond it ions:
a) The work must carry prominent notices stating that you modified it, and giving a
relevant date.
b) The work mus t carry prominent notices stating that it is rel eased under this License and
any conditions added under section 7. This requirement modifies the requirement in
section 4 to “keep inta ct all notices ”.
c) You must license the entire work, as a whole, under this License to anyone who comes
into possession of a copy. This License will therefore apply, along with any applicable
section 7 additional terms, to the whole of the work, and all its parts, regardless of how
they are packaged. This License gi ves no perm ission to l icense the w ork in an y o ther w ay,
but it doe s not invalidate such permission if you have separately received it.
d) If the work has interactive user interfaces, each must display Appropriate Legal Notices;
however, if the Program has interactive interfaces that do not display Appropriate Legal
Notices, your work need not make them do so.
A compilation of a covered work with other separate and independent works, which are not
by their nature extensions of the covered work, and which are not combined with it such as
48
to form a larger program, in or on a volume of a storage or distribution medium, is called an
“aggregate” if the compilation and its resulting copyright are not used to limit the access or
legal rights of the compilation's users beyond what the individual works permit. Inclusion of
a covered work in an aggregate does not cause this License to apply to the other parts of
the aggregate.
6. Conveying Non-Source Forms.
You m ay convey a covered work in object code form under the terms of sections 4 and 5,
provided that you also convey the machine-readable Corresponding Source under th e
terms of this License, in one of these ways:
a) Convey the object code in, or embodied in, a physical product (including a physical
distribution medium), accompanied by the Corresponding Source fixed on a durable
physical medium customarily used for software interchange.
b) Convey the object code in, or embodied in, a physical product (including a physical
distribution medium), accompanied by a written offer, valid for at least three years and
valid for as long as you offer spare parts or customer support for that product model, to
give an yone who possesse s the object code either (1) a copy of the Corr esponding Source
for all the software in the product that is covered by this License, on a durable physical
medium customarily used for software interchange, for a price no more than your
reasonable cost of physically performing this conveying of source, or (2) access to copy the
Corresponding Source from a network server at no charge.
c) Convey individual copies of the object code with a copy of the written offer to provide the
Corresponding Source. This alternative is allowed only occasionally and noncommercially,
and only if you received the object code with such an offer, in accord with subsection 6b.
d) Convey the object code by offering access from a designated place (gratis or for a
charge), and offer equivalent access to the Corresponding Source in the same way through
the same place at no further charge. You need not require recipients to copy the
Corresponding Source al ong with th e object co de. If the pl ace to copy t he object code is a
network server, the Corresponding Source may be on a different server (operated by you or
a third party) that supports equivalent copying f acilities, provided you maintain clear
directions next to the object code saying where to find the Corresponding Source.
Regardless of what server hosts the Corresponding Source, you remain obligated to ensure
that it is available for as long as needed to satisfy these requirements.
e) Convey the object code using peer-to-peer transmission, provided you inform other
peers where the object code and Corresponding Source of the work are being offered to the
general public at no charge under subsection 6d.
A separable portion of the object code, whose source code is excluded from the
49
Corresponding Source as a System Library, need not be included in conveying the object
code work.
A “User Product” is either (1) a “consumer product”, which means any tangible personal
property which is normally used for personal, family, or household purposes, or (2)
anything designed or sold for incorporation into a dwelling. In determining whether a
product is a consume r product, doubtful cases shal l be resolved in fa vor of co verage. F or a
particular product received by a particular user, “normally used” refers to a typical or
common use of that class of product, regardless of the status of the particular user or of the
way in which the particular user actually uses, or expects or is expected to use, the product.
A product is a consumer product regardless of whether the product has substantial
commercial, industrial or non-consumer uses, unless such uses represent the only
significant mode of use of the product.
“Installation Information” for a User Product means any methods, procedures,
authorization keys, or other information required to install and execute modified versions
of a covered work in that User Product from a modified version of its Corresponding Source.
The information must suffice to ensure that the continued functioning of the modified
object code is in no case prevented or interfered with solely because modification has been
made.
If you convey an object code work under this section in, or with, or specifically for use in,
a User Product, and the conveying occurs as part of a transaction in which the right of
possession and use of the User Product is transfe rred to the reci pient in perpetuity or for a
fixed term (regardless of how the transaction is characterized), the Corresponding Source
conveyed under this section must be accompanied by the Installation Information. But this
requirement does not apply if neither you nor any third party retains the ability to in stall
modified object c ode on the User Product (for examp le, th e work has been installed in
ROM).
The requirement to provide Installation Information does not include a requirement to
continue to provide support service, warranty , or updates for a work that has been modified
or installed by the recipient, or for the User Product in which it has been modified or
installed. Access to a network may be denied when the modification itself materially and
adversely affects the operation of the network or violates the rules and protocols for
communication across the network.
Corresponding Source conveyed, and Installation Information provided, in accord with this
50
section must be in a format that is publicly documented (and with an implementation
available to the public in source code form), and must require no special password or key
for unpacking, reading or copying.
7. Additional Te r m s.
“Additional permissions” are terms that supplement the terms of this License by making
exceptions from one or more of its conditions. Additional permissions that are applicable to
the entire Program shall be treated as th o ugh they were included in this License, to the
extent that they are valid under applicable law . If additional permissions apply only to part
of the Program, that part may be used separately under those permissions, but the entire
Program remains governed by this License without regard to the additional permi s s ions .
When you conv ey a copy of a covered work, yo u may at your option remove any additional
permissions from that copy, or from any part of it. (Additional permissions may be written
to require their own removal in certain cases when you modify the work.) You may place
additional permissions on material, added by you to a cove red work, for which you have or
can give appropriate copyright permission.
Notwithstanding any other provision of this License, for material you add to a covered work,
you may (if authorized by the copyright holders of that material) supplement the terms of
this License with terms:
a) Disclaiming warranty or limiting liability differently from the terms of sections 15 and 16
of this License; or
b) Requiring preservation of specified reasonable legal notices or author attributions in that
material or in the Appropriate Legal Notices displayed by works containing it; or
c) Prohibiting misrepresent at ion of the origin of that material, or requiring that modified
versions of such material be marked in reasonable ways as different from the original
version; or
d) Limi ting the use for publicity purposes of names of licensors or authors of the material;
or
e) Declining to grant rights under trademark law for use of some trade names, trademarks,
or service marks; or
f) Requiring indemnification of licensors and authors of that material by anyone who
conveys the material (or modified versions of it) with contractual assumptions of liability to
the recipient, for an y l iabili ty that t hese contractual assumptions directly i mpose on those
licensors and authors.
All other non-permissive additional terms are considered “further restrictions” within the
51
meaning of section 10. If the Program as you received it, or any part of it, contains a notice
stating that it is governed by this License along with a term that is a further restriction, you
may remove that term. If a license document contains a further restriction but permits
relicen sing or conveying under this License, you may add to a covered work mate rial
governed by the terms of that license document, provided that the further restriction does
not survive such relicensing or conveying.
If you add terms to a covered work in accord with this section, you must place, in the
relevant source files, a statement of the additional terms that apply to those files, or a
notice indicatin g where to find the applicable terms.
Additional terms, permissive or non-permissive, may be stated in the form of a separately
written licen se, or stated as exceptions; the above requirements apply either way.
8. Termination.
You may not propagate or mo dif y a covered work except as expressl y pr ovi ded unde r this
License. Any attempt otherwise to propagate or modify it is void, and will automatically
terminate your rights under this License (including any patent licenses granted under the
third paragraph of section 11).
However, if you cease all violation of this License, then your license from a particular
copyright holder is reinstated (a) provisionally, unless and until the copyright holder
explicitly and finally termin ates your license, and (b) permanently, if the copyright holder
fails to notify you of the violation by some reasonable means prior to 60 days after the
cessation.
Moreover, your license from a particular copyright holder is reinstated permanently if the
copyright holder notifies you of the violation by some reasonable means, this is the first
time you have received notice of violation of this License (for any work) from that copyright
holder, and you cure the violation prior to 30 days after your receipt of the notice.
Termination of your rights under this section does not terminate the licenses of parties who
have received copies or rights from you under this License. If your rights have been
terminated and not permanently reinstated, you do not qualify to receive new licenses for
the same material und er section 10.
9. Acceptance Not Required for Having Copies.
Y ou are not required to accept this License in order to receive or run a copy of the Program.
52
Ancillary propagation of a covered work occurring solely as a consequence of using
peer-to-peer transmission to receive a copy likewise does not require acceptance. However,
nothing other than this License grants you permission to propagate or modify any covered
work. These actions infringe copyright if you do not accept this License. Therefore, by
modifying or propagating a covered work, you indicate your acceptance of this License to
do so.
10. Automatic Licensing of Downstream Recipients.
Each time you convey a covered work, the recipient automatically receives a license from
the original licensors, to run, modify and propagate that work, subject to this License. You
are not responsible for enforcing compliance by third parties with this License.
An “entity transaction” is a transaction transferring control of an organization, or
substantially all assets of one, or subdividing an organization, or merging organizations. If
propagation of a covered work results from an entity transaction, each party to that
transaction who receives a copy of the work also receives whatever licenses to the work the
party's predecessor in interest had or could give under the previous paragraph, plus a right
to possession of the Corresponding Source of the work from the predecessor in interest, if
the predecessor has it or can get it with reasonable efforts.
You may not impose any further restrictions on the exercise of the rights granted or
affirmed under th is L icense. For example, you may not impose a license f ee, royalty, or
other charge for exercise of rights granted under this License, and you may not initiate
litigat ion (inclu ding a cross-claim or counterclaim in a lawsuit) alle ging th at any patent
claim is infringed by making, using, selling, offering for sale, or importing the Program or
any portion of it.
11. Patents.
A “contributor” is a copyright holder who authorizes use under thi s License of the Progr am
or a work on which the Program is based. The work thus licensed is called the contributor's
“contributor version”.
A contributor's “essential patent claims” are all patent claims owned or controlled by the
contributor, whether already acquired or hereafter acquired, that would be infringed by
some manner, permitted by this License, of making, using, or selling its contributor version,
but do not include claims that would be infringed only as a consequence of further
modification of the contributor version. For purposes of this definition, “control” includes
the right to gra nt p a te nt sublicens e s i n a m a nner consistent with the requirem e nts o f t hi s
53
License.
Each contributor grants you a non-exclusive, worldwide, royalty-free patent license under
the contributor's essential patent claims, to make, use, sell, offer for sale, import and
otherwise run, modify and propagate the contents of its contributor version.
In the following three paragraphs, a “patent license” is any express agreement or
commitment, however denominated, not to enforce a patent (such as an express
permission to practice a patent or covenant not to sue for patent infringement). To “grant”
such a patent license to a party means to make such an agreement or commitment not to
enforce a patent against the party.
If you convey a covered work, knowingly relying on a patent license, and the Corresponding
Source of the work is not a vail able for anyone to copy, free of charge and under the terms
of this License, through a publicly available network server or other readily accessible
means, then you must either (1) c ause the Corr esponding Source to be so av ailable, or (2)
arrange to deprive yourself of the benefit of the patent license for this particular work, or (3)
arrange, in a manner consistent with the requirements of this License, to extend the patent
license to downstream recipients. “Knowingly relying” means you have actual knowledge
that, but for the patent license, your conveying the covered work in a country, or your
recipient's use of the covered work in a country, would infringe on e or more identifiable
patents in that country that you have reason to believe are valid.
If, pursuant to or in connection with a single transaction or arrangement, you convey, or
propagate by procuring conveyance of, a covered work, and grant a patent license to some
of the parties receiving the covered work authorizing them to use, propagate, modify or
convey a specific copy of the covered work, then the patent lic e nse you grant is
automatically extended to all recipients of the covered work and works based on it.
A paten t license is “discriminat ory” if it d o e s not include within the scope of its coverage,
prohibits the ex ercise of, or is conditioned on the non-exercise of one or more of the rights
that are specifi cally granted unde r this License. You may not con vey a covered wor k if you
are a party to an arrangement with a third party that is in the business of distributing
software, under which you make payment to the third party based on the extent of your
activity of conveying the work, and under which the third party grants, to any of the parties
who would receive the covered work from you, a discriminatory patent license (a) in
connection with copies of the covered work conveyed by you (or copies made from those
copies), or (b) primarily for and in connection with specific products or compilations that
54
contain the covered work, unless you entered into that arrangement, or that patent license
was granted, prior to 28 March 2007.
Nothing in this License shall be construed as excluding or limiting any implied license or
other defenses t o in fringement that may otherwise be available to you under applicable
patent law.
12. No Surrender of Others' Freedom.
If conditions are imposed on you (whether by court order, agreement or otherwise) t hat
contradict the conditions of this License, they do not excuse you from the conditions of this
License. If you cannot convey a covered work so as to satisfy simultaneously your
obliga tio ns under this License a nd any o ther pe r tinent obli ga tions, then a s a cons equence
you may not convey it at all. For example, if you agree to terms that obligate you to collect
a royal ty for further conveying from those to whom you con vey the Pro gram, the o nly way
you could satisfy both those terms and this License would be to refrain entirely from
conveying the Program.
13. Use with the GNU Affero General Public License.
Notwithstanding any other provision of this License, you have permission to link or combine
any covered work with a work licensed under version 3 of the GNU Affero General Public
License into a single combined work, and to convey the resulting work. The terms of this
License will continue to apply to the part which is the covered work, but the special
require me nts of the G NU Affe ro Ge ne ral Public Lice nse, s ec ti on 1 3, con ce rni ng i nte raction
through a network will apply to the combination as such.
14. Revised Versions of this License.
The Free Software Foundation may publish revised and/or new versions of the GNU General
Public License from tim e to time. Such new versions will be sim ilar in spirit t o the present
version, but may differ in detail to address new problems or concerns.
Each vers ion is given a distinguishing version number. If the Program specifies that a
certain numbered version of the GNU Gener al Public License “or an y later v ersion” appli es
to it, you have the option of following the terms and conditions either of that numbered
version or of any later version published by the Free Software Foundation. If the Program
does not specify a version number of the GNU General Public License, you may choose any
version ever published by the Free Software Foundation.
If the Program specifies that a pro xy can decide which future versions of the GNU General
55
Public License can be used, that proxy's public statement of acceptance of a version
permanently authorizes you to choose that version for the Program.
Later lice nse versions may give you addition al or differe nt permissions. However, no
additional obligations are imposed on any author or copyright holder as a result of your
choosing to follow a later version.
15. Disclaimer of Warranty.
THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE
LAW. EXCEPT WHEN O THERWISE ST A TED IN WRITING THE COPYRIGHT HOLDERS AND/OR
OTHER PARTIES PROVIDE THE PROGRAM “AS IS” WITHOUT WARRANTY OF ANY KIND,
EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE
ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU.
SHOULD TH E PR O G R AM PROVE DEFECTI V E, YOU ASSUME THE COST O F ALL NECESSARY
SERVICING, REPAIR OR CORRECTION.
16. Limit ation of Liability.
IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL
ANY COPYRIG HT H OL DER, O R A NY OTHER PARTY WHO MOD IFI ES A ND /OR CONV E YS TH E
PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY
GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE
USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF
DA T A OR DA T A BEING RENDERED INACCURA TE OR LOSSES SUST AINED BY YOU OR THIRD
PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS),
EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES.
17. Interpretation of Sections 15 and 16.
If the disclaimer of warranty and limitation of liability provided above cannot be given local
legal effect according to their terms, reviewing courts shall apply local law that most closely
approximates an absolute waiver of all civil liability in connection with the Program, unless
a warranty or assumption of liability accompanies a copy of the Program in return for a fee.
END OF TERMS AND CONDITIONS