Table of Contents
- Table of Contents
- Safety Warnings
- Chapter 1. CPU and Memory Specifications
- Chapter 2. Power Button and Reset Button Behavior
- Chapter 3. USB One Touch Copy
- Chapter 4. LED and Alarm Buzzer Specifications
- Chapter 5. Upgrade Memory on QNAP Turbo NAS (RAM Module Installation)
- 5.1 TS-453Bmini, TS-453mini (4-bay)
- 5.2 TBS-453A
- 5.3 TS-451S, TS-531P, TS-531X, TS-651, TS-831X, TS-851, TS-x53/x53S Pro, TS-563, TVS-882S, TVS-882ST, TVS-x63, TS-x53Aseries (2/4/6/8-bay)
- 5.4 TS-1635
- 5.5 TVS-473, TVS-673, TVS-873
- 5.6 TS-431U, TS-x31XU series, TS-451U, TS-x53U, TS-x63U series (4/8/12-bay)
- 5.7 TS-251+, TS-251, TS-451+, TS-451, TS-251A, TS-451A
- 5.8 IS-453S
- Chapter 6. Network Expansion Card Installation
- Chapter 7. Install and Hot-swap Hard Drives
- 7.1 Install Hard Drives
- 7.1.1. TS-x51, TS-x51A, TVS-x63, TS-563, TS-x53 Pro, TS-651, TS-831X, TS-851, TS-531X, TS-531P, TS-x53A, TS-x31, TS-x31+, TS-x31P, TS-431U, TS-x31XU, TS-451U, TS-x53U, TS-x63U
- 7.1.2. TS-1635
- 7.1.3. TS-453Bmini, TS-453Mini
- 7.1.4. TVS-473, TVS-673, TVS-873
- 7.1.5. TS-112P, TS-212P and TS-251C
- 7.1.6. TAS-168, TAS-268, TS-128, TS-228
- 7.1.7. IS-453S
- 7.2 Hot-swap Hard Drives
- 7.1 Install Hard Drives
- Chapter 8. Install M.2 SSDs
- Chapter 9. RAID Recovery
- Chapter 10. Use the LCD Panel
- Chapter 11. Install Power Supply Unit
- Technical Support
- GNU GENERAL PUBLIC LICENSE
- Appendix A: Product Compliance Class
QNAP TS-831XU User Manual
Displayed below is the user manual for TS-831XU by QNAP which is a product in the NAS & Storage Servers category. This manual has pages.
Related Manuals
QNAP Turbo NAS
Hardware User Manual
© 2017. QNAP Systems, Inc. All Rights Reserved.
2
Thank you for choosing QNAP products! This user manual provides description of the
hardware of the T urbo NAS and relevant guideline of certain functions. Please read carefully
and strictly adhere to the instructions of the manual.
This user manual is applicable to the following Tu rb o NAS models:
HS-210, HS-251, HS-251+, TS-112P, TS-131, TS-212P, TS-231, TS-231+, TS-251,
TS-251+, TS-251C, TS-251A, TS-253 Pro , TS-431, TS-431+, TS-431U, TS-451, TS-451+,
TS-451S, TS-451U, TS-451A, TS-453 Pro, TS-453S Pro (formerly SS-453 Pro), TS-453U,
TS-453U-RP, TS-463U, TS-463U-RP, TVS-463, TS-470U-SP/RP, TVS-473, TS-531P,
TS-563, TS-651, TS-653 Pro, TVS-663, TS-531X, TVS-673, TS-831X, TS-851, TS-853 Pro,
TS-853S Pro (formerly SS-853 Pro), TS-853U, TS-853U-RP, TS-863U, TS-863U-RP,
TVS-863, TVS-863+, TVS-882ST, TS-870U-RP, TVS-873, TS-879 P ro, T S-879U-RP,
TS-EC879U-RP, TS-1079 Pro, TS-1253U, TS-1253U-RP, TS-1263U, TS-1263U-RP,
TS-1270U-RP, TS-1279U-RP, TS-EC1279U-RP, TS-1635, TS-1679U-RP, TS-EC1679U-RP,
IS-453S, TS-453Bmini, TS-453mini, TAS-168, TAS-268, TS-253A, TS-453A, TS-653A,
TS-853A, TS-128, TS-228, TBS-453A, TS-131P, TS-231P, TS-431P, TS-431XU,
TS-431XU-RP, TS-831XU, TS-831XU-RP, TS-1231XU, TS-1231XU-RP
NOTE
• The “Turbo NAS”& “Turbo vNAS” are h ereaf t er referred to as “N AS”.
• The product you purchased may not support certain functions dedicated to specific
models.
• All features, functionality, and other product specifications are subject to change
without prior notice or obligation.
• Information presented is subject to change without notice.
• No part of this publication may be reproduced, stored in a retrieval system, or
transmitted, in any form or by any means, mechanical, electronic, photocopyin g ,
recording, or otherwise, without prior written permission of QNAP Systems, Inc.
QNAP and the QNAP logo are registered trademarks of QNAP Systems, Inc. Other
products and comp any names ment ioned herein may be the trademarks of their
respective companies.
3
DISCLAIMER
In no eve nt shall QNAP S ystems, Inc. (QNAP) liability exceed the price paid for the product
from direct, indirect, special, incidental, or consequential damages resulting from the use
of the product, its accompanying software, or its documentation. QNAP makes no warranty
or representation, expressed, implied, or statutory, with respect to its products or the
contents or use of this documentation and all accompanying software, and specifically
disclaims its quality, performance, merchantability, or fitness for any particular purpose.
QNAP reserves the right to revise or update its products, software, or documentation
without obligation to notify any individual or entity.
Note:
Back up your system periodically to avoid any potential data loss. QNAP disclaims any
respon sibility o f all sorts of d ata loss or recovery.
Should you return any components of the NAS package for refund or maintenance,
make sure they are carefully packed for shipping. Any form of damages due to
improper packaging will not be compensated.
4
Regulatory Notice
FCC Notice
QNAP NAS comply with different FCC compliance classes. Please refer the Appendix for
details. Once the class of the device is determined, refer to the following corresponding
statement.
=======================================================
FCC Class A Notice
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1. This device may not cause har mfu l interference.
2. This device must accept any interference received, includ ing interference th at may
cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interferen c e when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency
energy, and if not insta lled and used i n accordance with the instr uction manual, may cause
harmful interference to radio communications. Oper ation of this equipment in a residential
area is likely to cause harmful interference, in which case the user will be required to
correct the interf er ence at his own expense.
Modifications: Any modifications made to this device that are not approved by QNAP
Systems, Inc . may void the auth ority granted to the user by the FC C to o perate this
equipment.
A급기기
(업무용정보통신기기)
이기기는업무용으로전자파적합등록을한기기이오니, 판매자또는사용자는이점을주위하시기바라며,
만약잘못판매또는구입하였을때에는가정용으로교환하시기바랍니다.
5
FCC Class B Notice
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1. This device may not cause har mfu l interference.
2. This device must accept any interference received, includ ing interference th at may
cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interferen c e in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause h armful interf eren c e t o radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation betw een the equipment and rec eiver.
• Connect t he equipment into an outlet on a ci rcuit differe nt from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/television technic ian for he lp.
Modifications: Any modifications made to this device that are not approved by QNAP
Systems, Inc . may void the auth ority granted to the user by the FC C to o perate this
equipment.
CE NOTICE
QNAP NAS comply with different CE compliance classes. Please refer to the Appendix for
details.
6
SJ/T 11364-2006
本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符合中国 RoHS 标准规定的限量
要求。
本产品上会附有”环境友好使用期限”的标签，此期限是估算这些物质”不会有泄漏或突变”的年限。本产
品可能包含有较短的环境友好使用期限的可替换元件，像是电池或灯管，这些元件将会单独标示出来。
部件名称 有毒有害物质或元素
铅
(Pb)
汞
(Hg)
镉
(Cd)
六价铬
(CR(VI))
多溴联苯
(PBB)
多溴二苯醚
(PBDE)
壳体 O O O O O O
显示 O O O O O O
印刷电路板 O O O O O O
金属螺帽 O O O O O O
电缆组装 O O O O O O
风扇组装 O O O O O O
电力供应组装 O O O O O O
电池 O O O O O O
O: 表示该有毒有害物质在该部件所有物质材料中的含量均在 SJ/T11363-2006 标准规定的限量要求以下。
X: 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T11363-2006 标准规定的限量要求。
7
Symbols in this document
Warning
This icon indicates the instructions must be strictly followed. Failure
to do so could result in injury to human body or death.
Caution
This icon indicates the action may lead to disk clearance or loss OR
failure to follow the instructions could result in data damage, disk
damage, or product damage.
8
Table of Contents
Contents
Table of Contents ............................................................................................... 8
Safety Warnings ............................................................................................... 10
Chapter 1. CPU and Memory Specifications ................................................... 11
Chapter 2. Power Button and Reset Button Behavior .................................... 39
Chapter 3. USB One Touch Copy .................................................................... 40
Chapter 4. LED and Alarm Buzzer Specifications ........................................... 41
Chapter 5. Upgrade Memory on QNAP Turbo NAS (RAM Module Installation) 44
5.1 TS-453BMINI, TS-453MINI (4-BAY) ............................................................. 44
5.2 TBS-453A ............................................................................................ 46
5.3 TS-451S, TS-531P, TS-531X, TS-651, TS-831X, TS-851, TS-X53/X53S PRO,
TS-563, TVS-882S, TVS-882ST, TVS-X63, TS-X53ASERIES (2/4/6/8-BAY) ................... 48
5.4 TS-1635 .............................................................................................. 49
5.5 TVS-473, TVS-673, TVS-873 ................................................................... 53
5.6 TS-431U, TS-X31XU SERIES, TS-451U, TS-X53U, TS-X63U SERIES (4/8/12-BAY) .. 55
5.7 TS-251+, TS-251, TS-451+, TS-451, TS-251A, TS-451A ............................. 57
5.8 IS-453S .............................................................................................. 60
Chapter 6. Network Expansion Card Installation ........................................... 63
6.1 TVS-463, TS-531P, TS-531X, TVS-663, TS-831X, TVS-863, TS-563, TS-879 PRO,
TS-1079 PRO, TS-463U, TS-463U-RP .................................................................. 63
6.2 TS-1635 .............................................................................................. 67
6.3 TVS-473, TVS-673, TVS-873 ................................................................... 71
6.4 TS-431XU, TS-463U, TS-463U-RP, TVS-471 SERIES ..................................... 74
6.5 TS-831XU, TS-863U, TS-863U-RP, TS-1231XU, TS-1263U, TS-1263U-RP SERIES
78
Chapter 7. Install and Hot-swap Hard Dri ve s ................................................ 81
7.1 INSTALL HARD DRIVES ............................................................................... 81
7.1.1. TS-x51, TS-x51A, TVS-x63, TS-563, TS-x53 Pro, TS-651, TS-831X, TS-851,
TS-531X, TS-531P, TS-x53A, TS-x31, TS-x31+, TS-x31P, TS-431U, TS-x31XU,
TS-451U, TS-x53U, TS-x63U ......................................................................... 81
7.1.2. TS-1635 ....................................................................................... 83
7.1.3. TS-453Bmini, TS-453Mini ................................................................ 85
9
7.1.4. TVS-473, TVS-673, TVS-873 ............................................................ 88
7.1.5. TS-112P, TS-212P and TS-251C ....................................................... 91
7.1.6. TAS-168, TAS-268, TS-128, TS-228 .................................................. 93
7.1.7. IS-453S ........................................................................................ 96
7.2 HOT-SWAP HARD DRIVES ............................................................................ 99
Chapter 8. Install M.2 SSDs ......................................................................... 103
8.1 M.2 SSD HEAT SINK INSTALLATION ............................................................. 103
8.2 M.2 SSD INSTALLATION ........................................................................... 104
8.2.1 TBS-453A ................................................................................... 104
8.2.2 TVS-473, TVS-673, TVS-873 .......................................................... 105
Chapter 9. RAID Reco ver y ........................................................................... 109
Chapter 10. Use the LCD Panel ...................................................................... 111
Chapter 11. Install Power Supply Unit ........................................................... 117
11.1 1U TURBO NAS WITH HOT-SWAPPABLE PSU ................................................... 117
11.2 2U/3U TURBO NAS (TS-831XU-RP, TS-1231XU-RP, TS-853U-RP, TS-1253U-RP
ONLY) 118
Technical Support .......................................................................................... 121
GNU GENERAL PUBLIC LICENSE ..................................................................... 122
Appendix A: Product Compliance Class ........................................................... 135
10
Safety Warnings
1. The NAS can operate normally in the temperature range of 0 ºC–40ºC (or up to 35ºC
depending on individual product specifications) with a relative humidity of 0%–95%.
Ensure that the environment is well-ventilated.
2. The power cord and devices connected to the NAS must provide correct supply voltage
(100W, 90–264V).
3. Do not pl ace the NA S in dire ct sunli ght or near che micals. Ma ke sure the tempe rat ure
and humidi ty of the environment are in o ptimized level.
4. Unplug the power cor d and all connected cabl es before cleaning. Wi pe the NAS with a
dry towel. Do not use chemical or aerosol to clean the NAS.
5. Do not place any objects on the NAS for the server’s n ormal operation and to avoid
overheat.
6. Use the flat head screws in the product package to lock the hard disks in the NAS when
installing hard disks for proper operation.
7. Do not place the NAS near any liquid.
8. Do not place the NAS on any uneven surface to avoid falling off and damage.
9. Make sure the voltage is correct in the location where the NAS is installed. Contact the
distributor or the local power supply company for the information.
10. Do not place any object on the power cord.
11. Do not attempt to repair the NAS in any occasions. Improper disassembly of the
product may expose the users to electric shock or other risks. For any enquiries,
please contact the distributor.
12. The chassis NAS models should only be installed in the server room and maintained by
the authorized server manager or IT administrator. The server room is locked by key or
keycard access and only certified staff is allowed to enter the server room.
Warning:
Danger of explosion if battery is incorrectly replaced. Replace only with the same or
equivalent type recommended by the manufact urer. Dispose of us ed bat teries
according to the manufacturer’s instructions.
Do NOT touch the fan inside the system to avoid serious injuries.
11
Chapter 1. CPU and Memo ry Specifications
Caution: Modifying the hardware, software, or firmware of the QNAP produc ts will
void the warranty. QNAP is not responsible for any form of damage or loss of data caused
by modding the QNAP products. Users should bear their own risks of all sorts of possible
data loss or system instabilities due to changing the hardware parts, modifying the default
system firmware or installing any unauthorized third party applications on QNAP products.
System TS-112P TS-212P
CPU Marvell 1.6GHz Marvell 1.6GHz
Memory 512MB DDR2 512MB DDR2
Flash 16MB 16MB
Memory
replaceable
- -
Number of RAM
slots
- -
Number of hard
drive slots 1 2
System TS-128 TS-228
CPU Dual-core ARM®v7
1.1GHz
Dual-core ARM®v7
1.1GHz
Memory 1GB DDR 3 1GB DDR3
Flash 4GB 4GB
Memory
replaceable - -
Number of RAM
slots - -
Number of hard
drive slots 1 (3.5” HDDs only) 2 (3.5” HDDs only)
12
System TS-131 TS-231
CPU Dual-core
FreescaleTM 1.2GHz
Dual-core
FreescaleTM 1.2GHz
Memory 512MB DDR3 512MB DDR3
Flash 512MB 512MB
Memory
replaceable
- -
Number of RAM
slots
- -
Number of hard
drive slots 1 2
System TAS-168 TAS-268
CPU Dual-core Realtek
1.1GHz
Dual-core Realtek
1.1GHz
Memory 2GB DD R3 2GB DDR3
Flash 4GB 4GB
Memory
replaceable
- -
Number of RAM
slots
- -
Number of hard
drive slots 1 (3.5” HDDs only) 2 (3.5” HDDs only)
IR sensor ✔(QNAP remote
control: RM-IR003)
✔(QNAP remote
control: RM-IR003)
13
System TS-431 TS-431U
CPU Dual-core
FreescaleTM 1.2GHz
Dual-core
FreescaleTM 1.2GHz
Memory 512MB DDR3 1GB DDR3
Flash 512MB 512MB
Memory
replaceable
- -
Number of RAM
slots
- -
Number of hard
drive slots 4 4
System TS-231+ TS-431+
CPU
Annapurna Labs
Alpine AL -212
Dual-core 1.4GHz
Cortex-A15
Annapurna Labs
Alpine AL -212
Dual-core 1.4GHz
Cortex-A15
Memory 1GB DD R3 1GB DDR3
Flash 512MB 512MB
Memory
replaceable - -
Number of RAM
slots - -
Number of hard
drive slots 2 4
PCI-E expansion
slot - -
Built-in 10GbE LAN
ports - -
14
System TS-131P TS-231P TS-431P
CPU
Annapurna Labs
Alpine AL -212
Dual-core 1.7GHz
Cortex-A15
Annapurna Labs
Alpine AL -212
Dual-core 1.7GHz
Cortex-A15
Annapurna Labs
Alpine AL -212
Dual-core 1.7GHz
Cortex-A15
Memory 1GB DD R3 1GB DDR3 1GB DDR3
Flash 512MB 512MB
Memory
replaceable - -
Number of RAM
slots - -
Number of hard
drive slots 1 2 4
PCI-E expansion
slot - -
Built-in 10GbE LAN
ports - -
15
System TS-431XU TS-431XU-RP TS-831XU TS-831XU-RP
CPU Annapurna Labs Alpine AL-314 Quad-core 1.7GHz Cortex-A15
Memory 2GB DDR 3
(Expandable RAM, up to 16GB)
4GB DDR3
(Expandable RAM, up to 16GB)
Flash 512MB
Memory
replaceable
✔ (Compatible with DDR3 RAM)
Number of
RAM slots 2 (SODIMM)
Number of
hard drive
slots
4 8
PCI-E
expansion
slot
1 x PCIe 2.0 x2
Built-in
10GbE LAN
ports
2 x SFP+
System TS-1231XU TS-1231XU-RP
CPU Annapurna Labs Alpine AL-314 Quad-core
1.7GHz Cortex-A15
Memory 4GB DDR 3
(Expandable RAM, up to 16GB)
Flash 512MB
Memory
replaceable ✔ (Compatible with DDR3 RAM)
Number of RAM
slots 2 (SODIMM)
Number of hard
drive slots 12
PCI-E expansion
slot
1 x PCIe 2.0 x2
Built-in 10GbE LAN
ports 2 x SFP+
16
System TS-531P TS-531X TS-831X
CPU
Quad-
core Annapurna
Labs Alpine AL-314
1.4GHz Cortex-A15
Quad-core A
nnapurna
Labs Alpine AL-314
1.4GHz Cortex-A15
Quad-core A
nnapurna
Labs Alpine AL-314
1.4GHz Cortex-A15
Memory
2GB/8GB DDR3
(Expandable RAM, up
to 16GB)
2GB/8GB DDR3
(Expandable RAM, up
to 16GB)
8GB/16GB DDR3
(Expandable RAM, up
to 16GB)
Flash 512MB 512MB 512MB
Memory
replaceable
✔ (Compatible with
DDR3 RAM)
✔ (Compatible with
DDR3 RAM)
✔ (Compatible with
DDR3 RAM)
Number of RAM
slots 2 (SODIMM) 2 (SODIMM) 2 (SODIMM)
Number of hard
drive slots 5 5 8
PCI-E expansion
slot 1 1 1
Built-in 10GbE LAN
ports - 2 x SFP+ 2 x SFP+
System TS-1635 HS-210
CPU
Quad-
core Annapurna
Labs Alpine AL-514
1.7GHz Cortex-A15
Marvell 1.6GHz
Memory
8GB/16GB DDR3
(Expandable RAM, up
to 16GB)
512MB DDR3
Flash 512MB 16MB
Memory
replaceable
✔ (Compatible with
DDR3 RAM)
-
Number of RAM
slots 2 (SODIMM) -
Number of hard
drive slots 16 2
PCI-E expansion
slot 1
17
Built-in 10GbE LAN
ports 2 x SFP+
System TS-451U TS-453U TS-453U-RP
CPU
Dual-core
Intel® Celeron™
2.41GHz (up to
2.58GHz)
Quad-core
Intel® Celeron™
2.0GHz (up to
2.42GHz)
Quad-core
Intel® Celeron™
2.0GHz (up to
2.42GHz)
Memory
1GB DDR3L
(Expandable RAM, up
to 8GB)
4GB/8GB DDR3L
(Expandable RAM, up
to 8GB)
4GB/8GB DDR3L
(Expandable RAM, up
to 8GB)
Flash 512M B (USB DOM) 512MB (USB DOM) 512MB (USB DOM)
Memory
replaceable
✔ (Compatible with
DDR3L RAM)
✔ (Compatible with
DDR3L RAM)
✔ (Compatible with
DDR3L RAM)
Number of RAM
slots 2 (SODIMM) 2 (SODIMM) 2 (SODIMM)
Number of hard
drive slots 4 4 4
Power supply unit 250W 250W 2 x 250W
System TS-853U TS-853U-RP
CPU
Quad-core
Intel® Celeron™
2.0GHz (up to
2.42GHz)
Quad-core
Intel® Celeron™
2.0GHz (up to
2.42GHz)
Memory
4GB/8GB DDR3L
(Expandable RAM, up
to 8GB)
4GB/8GB DDR3L
(Expandable RAM, up
to 8GB)
Flash 512M B (USB DOM) 512MB (USB DOM)
Memory
replaceable
✔ (Compatible with
DDR3L RAM)
✔ (Compatible with
DDR3L RAM)
Number of RAM
slots 2 (SODIMM) 2 (SODIMM)
Number of hard
drive slots 8 8
Power supply unit 250W 2 x 250W
18
19
System TS-1253U TS-1253U-RP
CPU
Quad-core
Intel® Celeron™
2.0GHz (up to
2.42GHz)
Quad-core
Intel® Celeron™
2.0GHz (up to
2.42GHz)
Memory
4GB/8GB DDR3L
(Expandable RAM, up
to 8GB)
4GB/8GB DDR3L
(Expandable RAM, up
to 8GB)
Flash 512M B (USB DOM) 512MB (USB DOM)
Memory
replaceable
✔ (Compatible with
DDR3L RAM)
✔ (Compatible with
DDR3L RAM)
Number of RAM
slots 2 (SODIMM) 2 (SODIMM)
Number of hard
drive slots 12 12
Power supply unit 250W 2 x 250W
System IS-453S
CPU
Quad-core
Intel® Atom™
1.91GHz
Memory
IS-453S-2G: 2GB
DDR3L
IS-453S-8G: 8GB
DDR3L
Flash 512M B (USB DOM)
CPU replaceable -
Memory
replaceable
✔ (Compatible with
DDR3L-1333/1600S
ODIMM RAM)
Number of RAM
slots 2 (SODIMM)
Number of hard
drive slots 4 (2.5" only)
20
System TS-251C TS-251/
TS-251-4G
TS-251A-2G /
TS-251A-4G
CPU
Dual-core
Intel® Celeron™
2.41GHz (up to
2.58GHz)
Dual-core
Intel® Celeron™
2.41GHz (up to
2.58GHz)
Dual-core
Intel® Celeron™
1.6GHz (up to
2.48GHz)
Memory
1GB DDR3L 1GB / 4GB DDR3L
(Expandable RAM, up
to 8GB)
2GB / 4GB DDR3L
(Expandable RAM, up
to 8GB)
Flash 512MB 512MB 512MB
Memory
replaceable - ✔ (Compatible wit h
DDR3L RAM)
✔ (Compatible with
DDR3L-1600 RAM)
Number of RAM
slots - 2(SODIMM) 2(SODIMM)
Number of hard
drive slots 2 (3.5” HDDs only) 2 2
IR sensor ✔(QNAP remote
control: RM-IR002)
✔(QNAP remote
control: RM-IR002)
✔(QNAP remote
control: RM-IR002)
System TS-451 /
TS-451-4G
TS-451A-2G /
TS-451A-4G TS-451S
CPU
Dual-core
Intel® Celeron™
2.41GHz (up to
2.58GHz)
Dual-core
Intel® Celeron™
1.6GHz (up to
2.48GHz)
Dual-core
Intel® Celeron™
2.41GHz (up to
2.58GHz)
Memory
1GB / 4GB DDR3L
(Expandable RAM, up
to 8GB)
2GB / 4GB DDR3L
(Expandabl e RAM, up
to 8GB)
1GB DDR3L
(Expandabl e RAM, up
to 8GB)
Flash 512MB 512MB 512MB
Memory
replaceable
✔ (Compatible with
DDR3L RAM)
✔ (Compatible with
DDR3L-1600 RAM)
✔ (Compatible with
DDR3L RAM)
Number of RAM
slots 2 (SODIMM) 2(SODIMM) 2 (SODIMM)
Number of hard
drive slots 4 2 4 (2.5” only)
IR sensor ✔ (QNAP remote
control: RM-IR002)
✔(QNAP remote
control: RM-IR002)
✔ (QNAP remote
control: RM-IR002)
21
22
System TS-651 /
TS-651-4G
TS-851 /
TS-851-4G
CPU
Dual-core
Intel® Celeron™
2.41GHz (up to
2.58GHz)
Dual-core
Intel® Celeron™
2.41GHz (up to
2.58GHz)
Memory
1GB / 4GB DDR3L
(Expandable RAM, up
to 8GB)
1GB / 4GB DDR3L
(Expandable RAM, up
to 8GB)
Flash 512MB 512MB
Memory
replaceable
✔ (Compatible with
DDR3L RAM)
✔ (Compatible with
DDR3L RAM)
Number of RAM
slots 2 (SODIMM) 2 (SODIMM)
Number of hard
drive slots 6 8
IR sensor ✔ (QNAP remote
control: RM-IR002)
✔ (QNAP remote
control: RM-IR002)
System HS-251+ HS-251 /
HS-251-2G
CPU
Quad-core
Intel® Celeron™
2.0GHz (up to
2.42GHz)
Dual-core
Intel® Celeron™
2.41GHz (up to
2.58GHz)
Memory 2GB DD R3L 1 GB / 2 GB DDR3L
Flash 512MB 512MB
CPU replaceable - -
Memory
replaceable - -
Number of RAM
slots - -
Number of hard
drive slots 2 2
IR sensor ✔ (QNAP remote
control: RM-IR002)
✔ (QNAP remote
control: RM-IR002)
23
24
System
TBS-453A-4G/
TBS-453A-4G-1TB
/TBS-453A-4G-51
2GB
TBS-453A-8G/
TBS-453A-8G-1TB
/TBS-453A-8G-51
2GB
CPU
Quad-core
Intel® Celeron™
N3150 1.6GHz
(up to
2.08GHz)
Quad-core
Intel® Celeron™
N3150 1.6GHz (up to
2.08GHz)
Memory 4GB DDR 3L 8GB DDR3L
Flash 4GB 4GB
CPU replaceable - -
Memory
replaceable
✔ (Compatible with
DDR3L RAM)
✔ (Compatible with
DDR3L RAM)
Number of RAM
slots 2 (SODIMM) 2 (SODIMM)
Number of hard
drive slots 4 4
IR sensor
✔ (QNAP remote
control: RM-IR002 &
RM-IR003)
✔ (QNAP remote
control: RM-IR002 &
RM-IR003)
25
System TS-251+-2G /
TS-251+-8G
TS-253 Pro /
TS-253 Pro-8G
CPU
Quad-core
Intel® Celeron™
2.0GHz (up to
2.42GHz)
Quad-core
Intel® Celeron™
2.0GHz (up to
2.42GHz)
Memory
2GB / 8GB DDR3L
(Expandable RAM, up
to 8GB)
2GB / 8GB DDR3L
(Expandable RAM, up
to 8GB)
Flash 512MB 512MB
Memory
replaceable
✔ (Compatible with
DDR3L-1333/1600
RAM)
✔ (Compatible with
DDR3L-1333/1600
RAM)
Number of RAM
slots 2(SODIMM) 2(SODIMM)
Number of hard
drive slots 2 2
IR sensor ✔ (QNAP remote
control: RM-IR002)
✔ (QNAP remote
control: RM-IR002)
System TS-453Bmini-4G /
TS-453Bmini-8G
TS-453mini-2G /
TS-453mini-8G
CPU
Quad-core Intel®
Celeron™ J3455 1.5 GHz
(up to 2.3 GHz)
Quad-core Intel®
Celeron™ J1900 2.0GHz
(up to 2.42GHz)
Memory
4GB / 8GB DDR3L
(Expandable RAM, up
to 8GB)
2GB / 8GB DDR3L
(Expandable RAM, up
to 8GB)
Flash 512MB 512MB
Memory
replaceable
✔ (Compatible with
DDR3L RAM)
✔ (Compatible with
DDR3L-1333/1600
RAM)
Number of RAM
slots 2 (SODIMM) 2 (SODIMM)
Number of hard
drive slots 4 4
IR sensor ✔ (QNAP remote ✔ (QNAP remote
26
control: RM-IR002) control: RM-IR002)
System TS-451+-2G /
TS-451+-8G
TS-453 Pro /
TS-453 Pro-8G
TS-653 Pro /
TS-653 Pro-8G
CPU
Quad-core
Intel® Celeron™
2.0GHz (up to
2.42GHz)
Quad-core
Intel® Celeron™
2.0GHz (up to
2.42GHz)
Quad-core
Intel® Celeron™
2.0GHz (up to
2.42GHz)
Memory
2GB / 8GB DDR3L
(Expandable RAM, up
to 8GB)
2GB / 8GB DDR3L
(Expandable RAM, up
to 8GB)
2GB / 8GB DDR3L
(Expandable RAM, up
to 8GB)
Flash 512MB 512MB 512MB
Memory
replaceable
✔ (Compatible with
DDR3L RAM)
✔ (Compatible with
DDR3L RAM)
✔ (Compatible with
DDR3L RAM)
Number of RAM
slots 2 (SODIMM) 2 (SODIMM) 2 (SODIMM)
Number of hard
drive slots 4 4 6
LCD panel - ✔ ✔
IR sensor ✔ (QNAP remote
control: RM-IR002)
✔ (QNAP remote
control: RM-IR002)
✔ (QNAP remote
control: RM-IR002)
27
System TS-853 Pro /
TS-853 Pro-8G
TS-453S Pro
(Formerly the
SS-453 Pro)
TS-853S
Pro(Formerly the
SS-853 Pro)
CPU
Quad-core
Intel® Celeron™
2.0GHz (up to
2.42GHz)
Quad-core
Intel® Celeron™
2.0GHz (up to
2.42GHz)
Quad-core
Intel® Celeron™
2.0GHz (up to
2.42GHz)
Memory
2GB / 8GB DDR3L
(Expandabl e RAM, up
to 8GB)
4GB DDR3L
(Expandabl e RAM, up
to 8GB)
4GB DDR3L
(Expandabl e RAM, up
to 8GB)
Flash 512MB 512MB 512MB
Memory
replaceable
✔ (Compatible with
DDR3L RAM)
✔ (Compatible with
DDR3L RAM)
✔ (Compatible with
DDR3L RAM)
Number of RAM
slots 2(SODIMM) 2(SODIMM) 2(SODIMM)
Number of hard
drive slots 8 4 (2.5” only) 8 (2.5” only)
LCD panel ✔ - ✔
IR sensor ✔ (QNAP remote
control: RM-IR002)
✔ (QNAP remote
control: RM-IR002)
✔ (QNAP remote
control: RM-IR002)
28
System TS-563-4G /
TS-563-8G
TVS-463-4G /
TVS-463-8G
TVS-663-4G /
TVS-663-8G
CPU Quad-core AMD
2.0GHz
Quad-core AMD
2.4GHz
Quad-core AMD
2.4GHz
Memory
4/8 GB DDR3L
(Expandable RAM, up
to 16GB)
4/8 GB DDR3L
(Expandable RAM, up
to 16GB)
4/8 GB DDR3L
(Expandable RAM, up
to 16GB)
Flash 512MB 512MB 512MB
Memory
replaceable
✔ (Compatible with
DDR3L-1600 RAM)
✔ (Compatible with
DDR3L-1600 RAM)
✔ (Compatible with
DDR3L-1600 RAM)
Number of RAM
slots 2(SODIMM) 2(SODIMM) 2(SODIMM)
Number of hard
drive slots 5 4 6
PCI-E expansion
slot 1 1 1
HDMI - ✔ ✔
LCD panel - ✔ ✔
IR sensor - ✔ (QNAP remote
control: RM-IR002)
✔ (QNAP remote
control: RM-IR002)
29
System TVS-863-4G /
TVS-863-8G
TVS-863+-8G /
TVS-863+-16G
CPU Quad-core AMD
2.4GHz
Quad-core AMD
2.4GHz
Memory
4/8 GB DDR3L
(Expandable RAM, up to
16GB)
8/16 GB DDR3L
(Expandable RAM, up to
16GB)
Flash 512MB 512MB
Memory
replaceable
✔ (Compatible with
DDR3L-1600 RAM)
✔ (Compatible with
DDR3L-1600 RAM)
Number of RAM
slots 2(SODIMM) 2(SODIMM)
Number of hard
drive slots 8 8
PCI-E expansion
slot 1 1 (Pre-installed 1-port
10GbE NIC)
HDMI ✔ ✔
LCD panel ✔ ✔
IR sensor ✔(QNAP remote control:
RM-IR002)
✔ (QNAP remote
control: RM-IR002)
30
System TS-253A-4G /
TS-253A -8G
TS-453A -4G /
TS-453A -8G
TS-653A -4G /
TS-653A -8G
CPU
Quad-core Intel®
Celeron® N3150
1.6GHz (up to
2.08GHz)
Quad-core Intel®
Celeron® N3150
1.6GHz (up to
2.08GHz)
Quad-core Intel®
Celeron® N3150
1.6GHz (up to
2.08GHz)
Memory
4/8 GB DDR3L
(Expandable RAM, up
to 8GB)
4/8 GB DDR3L
(Expandable RAM, up
to 8GB)
4/8 GB DDR3L
(Expandable RAM, up
to 8GB)
Flash 512MB 512MB 512MB
Memory
replaceable
✔ (Compatible with
DDR3L-1600 RAM)
✔ (Compatible with
DDR3L-1600 RAM)
✔ (Compatible with
DDR3L-1600 RAM)
Number of RAM
slots 2(SODIMM) 2(SODIMM) 2(SODIMM)
Number of hard
drive slots 2 4 6
PCI-E expansion
slot - - -
HDMI 2 2 2
LCD panel - ✔ ✔
IR sensor ✔ (QNAP remote
control: RM-IR002)
✔ (QNAP remote
control: RM-IR002)
✔ (QNAP remote
control: RM-IR002)
31
System TS-853A -4G /
TS-853A -8G
CPU
Quad-core Intel®
Celeron® N3150
1.6GHz (up to
2.08GHz)
Memory
4/8 GB DDR3L
(Expandable RAM, up
to 8GB)
Flash 512MB
Memory
replaceable
✔ (Compatible with
DDR3L-1600 RAM)
Number of RAM
slots 2(SODIMM)
Number of hard
drive slots 8
PCI-E expansion
slot -
HDMI 2
LCD panel ✔
IR sensor ✔ (QNAP remote
control: RM-IR002)
32
System
TVS-882-i5-8G TVS-882-i7-16G
CPU
Quad-core Intel® CoreTM i5
1.9GHz
Quad-core Intel® CoreTM i7
2.6GHz
Memory
8GB DDR4 (Expandable RAM,
up t o 32GB)
16GB DDR4 (Expan dable
RAM, up to 32GB)
Flash
512MB
Memory replaceable
✔ (Compatible with DDR4 RAM)
Number of RAM slots
2(SODIMM)
Number of drive slots
8 x 2.5” SATA 6Gb/s
PCI-E expansion slot
1 x PCIe Gen3 (x8) + 1 x PCIe Gen3 (x4)
HDMI
1
LCD panel
✔
IR sensor
✔ (QNAP remote control: RM-IR002)
Thunderbolt
2 x Thunderbolt™ 2 ports
10GbE LAN
2 x 10GbE SFP+ LAN ports
33
System TVS-882ST2-i5-8G TVS-882ST2-i7-8G TVS-882ST2-i7-16G
CPU Quad-core Intel®
CoreTM i5 1.9GHz Quad-core Intel® CoreTM i7 2.6GHz
Memory
8GB DDR4
(Expandable RAM, up
to 32GB)
8GB DDR4
(Expandable RAM, up
to 32GB)
16GB DDR4
(Expandable RAM, up
to 32GB)
Flash 512MB
Memory
replaceable ✔ (Compatible with DDR4 RAM)
Number of RAM
slots 2 (SODIMM)
Number of
drive slots 8 x 2.5” SATA 6Gb/s
PCI-E
expansion slot
1 x PCIe Gen3 (x8) + 1 x PCIe Gen3 (x4)
Note: These two expansion slots are occupied by a Thunderbolt™
2
and a USB 3.1 expansion card.
HDMI 1
LCD panel ✔
IR sensor ✔ (QNAP remote control: RM-IR004)
Thunderbolt 2 x Thunderbolt™ 2 ports
10GbE LAN 2 x 10GbE SFP+ LAN ports
34
System
TVS-882ST3-i5-8G TVS-882ST3-i7-8G TVS-882ST3-i7-16G
CPU
Quad-core Intel®
CoreTM i5 1.9GHz
Quad-core Intel® CoreTM i7 2.6GHz
Memory
8GB DDR4
(Expandable RAM, up
to 32GB)
8GB DDR4 (Expandable
RAM, up to 32GB)
16GB DDR4
(Expandable RAM, up
to 32GB)
Flash
512MB
Memory
replaceable
✔ (Compatible with DDR4 RAM)
Number of RAM
slots
2 (SODIMM)
Number of
drive slots
8 x 2.5” SATA 6Gb/s
PCI-E
expansion slot
1 x PCIe Gen3 (x8) + 1 x PCIe Gen3 (x4)
Note: These two expansion slots are occupied by a Thunderbolt™ 2
and a USB 3.1 expansion card.
HDMI
2
LCD panel
✔
IR sensor
✔ (QNAP remote control: RM-IR004)
Thunderbolt
2 x Thunderbolt™ 3 ports
10GbE LAN
2 x 10GbE SFP+ LAN ports
35
System TVS-882S-i5-8G TVS-882S-i7-8G TVS-882S-i7-16G
CPU Quad-core Intel®
CoreTM i5 1.9GHz Quad-core Intel® CoreTM i7 2.6GHz
Memory
8GB DDR4
(Expandable RAM,
up t o 32GB)
8GB DDR4
(Expandable RAM,
up t o 32GB)
16GB DDR4
(Expandable RAM,
up t o 32GB)
Flash 512MB
Memory replaceable ✔ (Compatible with DDR4 RAM)
Number of RAM slots 2 (SODIMM)
Number of drive slots
8 x 2.5” SATA 6Gb/s
PCI-E expansion slot 1 x PCIe Gen3 (x8) + 1 x PCIe Gen3 (x4)
HDMI 2
LCD panel ✔
IR sensor ✔ (QNAP remote control: RM-IR004)
36
System TS-463U TS-463U-RP TS-863U
CPU Quad-core AMD
2.0GHz
Quad-core AMD
2.0GHz
Quad-core AMD
2.0GHz
Memory
4 GB DDR3L
(Expandable RAM, up
to 16GB)
4 GB DDR3L
(Expandable RAM, up
to 16GB)
4 GB DDR3L
(Expandable RAM, up
to 16GB)
Flash 512MB 512MB 512MB
Memory
replaceable
✔ (Compatible with
DDR3L-1600 RAM)
✔ (Compatible with
DDR3L-1600 RAM)
✔ (Compatible with
DDR3L-1600 RAM)
Number of RAM
slots 2(SODIMM) 2(SODIMM) 2(SODIMM)
Number of hard
drive slots 4 4 8
PCI-E expansion
slot
1 (Pre-installed
LAN-10G1SR-D NIC)
1 (Pre-installed
LAN-10G1SR-D NIC)
1 (Pre-installed
LAN-10G1SR-U NIC)
HDMI - - -
LCD panel - - -
37
System TS-863U-RP TS-1263U TS-1263U-RP
CPU Quad-core AMD
2.0GHz
Quad-core AMD
2.0GHz
Quad-core AMD
2.0GHz
Memory
4 GB DDR3L
(Expandable RAM, up
to 16GB)
4 GB DDR3L
(Expandable RAM, up
to 16GB)
4 GB DDR3L
(Expandable RAM, up
to 16GB)
Flash 512MB 512MB 512MB
Memory
replaceable
✔ (Compatible with
DDR3L-1600 RAM)
✔ (Compatible with
DDR3L-1600 RAM)
✔ (Compatible with
DDR3L-1600 RAM)
Number of RAM
slots 2(SODIMM) 2(SODIMM) 2(SODIMM)
Number of hard
drive slots 8 12 12
PCI-E expansion
slot
1 (Pre-installed
LAN-10G1SR-U NIC)
1 (Pre-installed
LAN-10G1SR-U NIC)
1 (Pre-installed
LAN-10G1SR-U NIC)
HDMI - - -
LCD panel - - -
38
System TVS-473 TVS-673 TVS-873
CPU AMD R-Series RX-421BD 2.1 GHz APU, Turbo Core up to 3.4 GHz
Memory 8GB DDR4 (Expandable
RAM, up to 64GB)
16GB DDR4
(Expandabl e RAM, up t o
64GB)
64GB DDR4
(Expandable RAM, up
to 64GB)
Flash 512MB
Memory
replaceable ✔ (Compatible with DDR4 RAM)
Number of
RAM slots 4 (SODIMM)
Number of
drive slots
4 x 3.5”/2.5” SATA
6Gb/s
6 x 3.5”/2.5” SATA
6Gb/s
8 x 3.5”/2.5” SATA
6Gb/s /s
PCI-E
expansion slot
2 x PCIe Gen3 (x4)
*One slot is pre-installed with a dua l-port USB 3.1 PCIe card.
HDMI 2
LCD panel ✔
IR sensor ✔ (QNAP remote control: RM-IR004)
USB 3.1 2 x USB 3.1 Gen 2 Ports
39
Chapter 2. Power Button and Reset Button Behavior
Power button: Press to turn on or turn off.
System Power button
(Turn on)
Power button
(Hardware turn
off)
Power button
(Force turn off)
All models
Press once 1.5 sec
5 sec
Reset button: Press to reset the system settings.
System Basic system reset
(1 beep)
Advanced system reset
(2 beeps)
All models 3 sec 10 sec
Basic system reset (3 sec)
Press the reset button for 3 seconds, a beep sound will be heard. The following settings are
reset to default:
System administration pass word: admin
TCP/IP configuration: Obtain IP address settings automatically via DHCP
TCP/IP configuration: Disable Jumbo Frame
TCP/IP configuration: If port trunking is enabled (dual LAN models only), the port
trunking mode will be reset to “Active Backup (Failover)”.
System Port: 8080 (system service port)
Security Level: Low (Allo w all conn e ctions)
LCD panel password: (blank)*
VLAN will b e disabled
*This feature is only provided by the NAS models w ith LCD panels . Please
visit http://www.qnap.comfor details.
Advanced system reset (10 sec)
Press the reset button for 10 seconds; you will hear two beeps at the third and the tenth
seconds. The NAS will reset all the system settings to default as it does by web-based
system reset in “Ad minist ration” > “Restore to Factory Default” except all the data are
reserved. The settings such as the users, user groups, and the network share folders
previously created will be cleared. T o retrieve the old data after the advanced system reset,
create the same network share folders on the NAS and the data will be accessible again.
40
Chapter 3. USB One Touch Copy
System Number of seconds (press the one touch copy button to
trigger data copy)
All NAS mod e ls 0.5 sec
Data Copy by the Front USB Port
The NAS supports instant data copy backup from the external USB device to the NAS or the
other w a y r o und b y t he fr on t one t ouc h co p y b utto n. To use this f unct io n, f ol lo w t he s te ps
below:
1. Make sure a hard drive is installed and formatted on the NAS. The default network
share Qusb or Usb is created.
2. Turn on the NAS.
3. Configure the behavior of the Copy button on “Backup” > “USB one touch copy” page.
4. Connect the US B storage device to the front USB port of the NAS.
5. Press the Cop y butto n. The USB L ED wi l l f lash. The da ta will be copie d to or from the
USB device according to the NAS settings.
Note:
This feature adopts incremental backup. After the first time data backup, the NAS only
copies the changed files since the last backup.
This feature is only available on certain N AS models. Please refer to the product
specification table for details at www.qnap.com.
41
Chapter 4. LED and Alarm Buzzer Specifications
The LED indicators of the NAS indicate the system status and information. When the NAS is
turned on, check the following items to make sure the system status is normal. Note that
the following LED information is applicable only when users have properly installed the hard
drive, and connected the NAS to the network and the power supply.
LED Color LED Status Description
System
Status Red/
Green
Flashes green
and red
alternately
every 0.5 sec
1. The hard drive on the NAS is being
formatted.
2. The NAS is being initialized.
3. The system firmware is being updat ed.
4. RAID rebuilding is in process.
5. Online RAID Cap a city Expansion is in
process.
6. Online RAID Level Migration is in process.
Red
1. The hard drive is invalid.
2. The dis k volume has rea ched its full
capacity.
3. The dis k volume is going to be fu ll.
4. The system fan is out of function.
5. An error occurs when accessing
(read/write) the disk data.
6. A bad sector is detected on the hard
drive.
7. The NAS is in degraded read-only mode
(2 member drives fail in a RAID 5 or RAID
6 configura ti on, the disk data can sti ll be
read).
8. Hardware self-test error.
Flashes red
every 0.5 sec
The NAS is in degraded mode (one member
drive fails in RAID 1, RAID 5 or RAID 6
configuration).
Flashes green
every 0.5 sec
1. The NAS is starting up.
2. The NAS is not configured.
3. A hard disk drive is not formatted.
Flashes green
every 2
seconds
The NAS is in S3 sleep mode1.
Green The NAS is ready.
Off All the hard disk drives on the N AS are in
standby mode.
1This feature is only available on certain NAS models. Please refer to the product specification table
for details at www.qnap.com.
42
LED Color LED Status Description
LAN Orange
Orange
The disk data is being accessed from the
network and a read/write error occurs during
the process.
Flashes
orange The NAS is being accessed from the network.
10GbE2 Green Green The 10GbE network expansion card is
installed.
Off No 10GbE network expansion card is installed.
HDD Red/
Green
Flashes red The disk data is being accessed and a
read/write error occurs during the process.
Red A hard disk drive read/write error occurs.
Flashes green The disk data is being accessed.
Green The hard disk drive can be accessed.
USB Blue
Flashes blue
every 0.5 sec
1. A USB device (connected to the front USB
port) is being detected.
2. A USB device (connected to the front USB
port) is being removed from the NAS.
3. The USB device (connected to the front
USB port of the NAS) is being accessed.
4. The data is being copied to or from the
external USB or eSATA device.
Blue A front USB device is detected (after the
device is mounted ).
Off
1. No USB device is detected.
2.
The NAS has fini shed copy ing the data to
or from the USB device conn ected to the
front USB port.
eSATA3 Orange Flashes The eSATA device is being accessed.
Off No eSATA device c an be detected.
2 The 10 GbE network expansion function is only supported on certain NAS models. Refer to the
product specification table for detail s at www.qnap.com.
3This feature is only available on certain NAS models. Please refer to the product specification table
for details at www.qnap.com.
43
Beep alarm (for all NAS models)
The beep alarm can be disabled in “System Administration” > “Hardware Settings”.
Beep sound Number of Times Description
Short beep (0.5 s ec) 1
1. The NAS is starting up.
2. The NAS is being shut down
(software shutdown).
3. The user presses the reset button to
reset the NAS.
4. The system firmware has been
updated.
Short beep (0.5 sec) 3 The user tries to copy the NAS data to the
external storage device from the front
USB port, but the data cannot be copied.
Long beep (1.5 sec) 3, ever y 5 min The system fan is out of function.
Long beep (1.5 sec)
2
1. The dis k volume is going to be full.
2. The dis k volume has rea ched its full
capacity.
3. The hard drives on the NAS are in
degraded mode.
4. The user starts the hard drive
rebuilding process.
5. A hard drive is plugged in or out.
1
1. The NAS is turned off by force
shutdown (hardware shutdown).
2. The NAS has been turned on
successfully and is ready.
44
Chapter 5. Upgrade Memory on QNAP Turbo NAS (RAM Module
Installation)
Warning:
The following instructions should only be performed by an authorized and trained
technician.
Strictly adhere to the instructions to install a RAM module on the NAS . Failure to do so
could result in injury to human body or death.
Before starting, please ensure that you turn off the NAS, disconnect the power
adaptor, network cable(s), and also remove any other device/cable that is attached to
the NAS.
Please ensure that you wear an antistatic wrist strap during the entire process to
prevent electro static discharge. The crocodile clip should be connected to the ground .
When installing more than one memory module, it is recommended to use the same
size and ideally the s ame type/ model in every slot.
QNAP provides different RAM modules (optional purchase) through its resellers for users to
upgrade the NAS memory. Use of non-QNAP RAM modules may cause system instability.
Follow the below steps to install an extra memory module on the NAS to upgrade the
memory.
Follow the steps below to ins tall a RAM mo dule on the N AS.
5.1 TS-453Bmini, TS-453mini (4-bay)
1. Use a flathead screwdriver to loosen the screw on the memory module compartment
at the bottom of the NAS and lift the compart ment cover away.
45
2. To remove installed memory modules, pull the retention clips on each side so that the
module tilts up for easy removal.
Note: Always ensure that a memory module is installed in the Primary (r ed) slot.
If not, then the system will fail to start. The maximum supported memory is 8GB
combined.
3. Slide the memory module to the slot at a 45-degree angle (appro ximately) and press
the memory module down until it clips into place. Ensure the memory module sits
46
properly with th e clips in place.
4. Close the NAS cover and fasten the screw. Reconnect the power and network cables
to the NAS.
5.2 TBS-453A
1. Remove the rubber feet and loosen the four hand screws on the bottom of the NAS.
Then lift the compa rtment cover away.
2. To remove installed memory modules, pull the retention clips on each side so that the
module tilts up for easy removal.
47
Note: Always ensure that a memory module is installed in the Primary (red) slo t.
If not, then the system will fail to start. The maximum supported memory is 8GB
combined.
3. Slide the memory module to the slot at a 45-degree angl e (approxim ately) and pr ess
the memor y m o dule dow n until it clips into place. Ensure th e memory module sits
properly with th e clips in place.
4. Close t he NAS cover, fasten the four hand screws, and replace the rubber feet.
Reconnect the power and network cables to the NAS.
48
5.3 TS-451S, TS-531P, TS-531X, TS-651, TS-831X, TS-851, TS-x53/x53S Pro,
TS-563, TVS-882S, TV S-882ST, TVS-x63, TS-x53Aseries (2/4/6/8-bay)
1. Loosen the three sc rews on the rear of the NAS.
2. Remove the case cover of the NAS gently.
3. Locate the memory slot . Make sure the slot is empty.
Note: For TS-x53/x53S Pro, TS-451S, TS-531P, TS-651, TS-851 and TS-x53A
models, always ensure that a memory module is installed in the Primary slot
(red). If not, then the system will fail to start. The maximum support ed memory is
8GB combined.
4. Grasp the edge of the memory module. Align the notch on the gold edge of the module
49
with the notch in the memory slot. Slide the memory module to the slot at a 45-degree
angle (approximately).
5. Gently press the memory module into th e slot until it is seated fully.
6. Rotate the memory module towards the motherboard until the securing clips clicks into
place.
7. Close the case cover and fasten the screws. Connect the power adaptor and cables
back to the NAS.
8. To check that the memory mod ule is recognized by the NAS, power up the NAS and
login the web interface as an administrator. Go to “System Status”>“System
Information” and check th e tot a l memory in “Hardware Information”.
5.4 TS-1635
1. Loosen the screws on the back of the NAS that are connecting the case cover to the
case.
50
2. Gently remove case cover from case.
3. To remove installed memory modules, gently pull the retention clips outwards o n e ach
side so that the module tilts up at a 45-degree angle for easy removal. Remove module.
51
4. Hold the memory modu le by grasping its edges. Align the notch on the RAM
module with the ridge in the memory socket. Slide the memory module into the
socket at a 45-degree angle. Ensure that the module is firmly ins e rted in to slot.
Note: Memory module must be installed in the primary slot (red outline in photo).
System will fail to start if primary slot is empty. The maximum supported memory per
slot i s 8 GB.
52
5. Gently push the memory module towards the motherboard until the retention clips
lock the memory module in plac e.
6. Close the case cover and fasten the screws. Connect the power adaptor and cables
to the NAS. Power on NA S.
7. To verify that th e memory module has been installed correctly and is being
recognized by the operating system, log into QTS as administrator.
o For QTS 4.3.0 and above: Go to “Control Panel” > “System”> “System
Status”>“Hardware Information” and check for Total memory.
o For QTS 4.2.x and below: Go to “Contro l Panel” > “System Settings”> “System
Status”>“Hardware Information” and check for Total memory.
53
5.5 TVS-473, TVS-673, TVS-873
1. Loosen the screws on the back of the NAS that are connecting the case cover to the
case.
2. Gently remove case cover from case.
54
3. To remove installed memory modules, gently pull the retention clips outwards o n e ach
side so that the module tilts up at a 30-degree angle for easy removal. Remove module.
4. Hold the memory module by grasping its edges. Align the notch on the RAM module
with the ridge in the memory socket. Slide the memory module into the socket at a
30-degree angle. Ensure that the module i s firmly inserted i nto the socket and that
the retention clamps are secure.
Note: The maximum supported memory is 64GB.
For one SODIMM module, insert memory into slot A2 or B2.
For two SODIMM modules using dual channel, insert memory into A1 and A2, B1 and B2,
or A2 and B2.
For three SODIMM modules, insert memory into A1 and A2 and B2 or B1 and B2 and A2.
55
5. Gently push the memory module towards the motherboard until the retention clips
lock the memory module in plac e.
6. Close the case cover and fasten the screws. Connect the power adaptor a nd cables
to the NAS. Power on NA S.
7. To verify that th e memory module has been installed correctly and is being
recognized by the operating system, log into QTS as administrator and go to
“Control Panel” > “System” > “System Status” > “Hardware Information” and
check for Total memory.
5.6 TS-431U, TS-x3 1XU series, TS-451U, TS-x53U, TS-x63U series
(4/8/12-bay)
1. Open the NAS.
a. TS-431XU, TS-451U, TS-453U, TS-463U series: Loosen all the screws on the top
of the NAS.
56
b. TS-831XU, TS-853U, TS-863U, TS-1231XU, TS-1253U, TS-1263U series: Loosen
the two screws on the rear of the NAS.
2. Open the NAS. Pull the retention clips on each side so that the module tilts up for easy
removal. Remove installed memory modules.
57
2. Slide the memory module t o the slot at a 45-degree angle (ap proximately).
3. Press the memory module down. Make sure the memory module sits in prop er ly with
the clips in place.
Note: For TS-x53U & TS-45 1 U mo dels , always ensure that a memory m odule is
installed in the primary slot (red box in the below figure,) or the system will fail to
start. The maximum supported memory is 8GB c o mb ined.
4. Close the NAS cover and fasten the screws. Connect the power adaptor and cables back
to the NAS.
5.7 TS-251+, TS-251, TS-451+, TS-451, TS-251A, TS-451A
1. Remo ve the screws on the rear (top and bottom) of the NAS. If you ha ve a 2-bay NAS,
58
it will have two screws. A 4-bay NAS will have four.
2. Gently r e m ove the case cover of th e NAS by sliding it a part (see th e un derside of the
NAS for visual indicators of the NAS case being locked/unlocked)
3. Remove the four inner screws (two on each side) of the hard drive cage.
4. If it is a 4-bay NAS, you will also need to remove two screws on the top of the hard drive
cage.
59
5. Gently r e m ove the hard drive cage from the NAS by lifting it out of its slot.
6. Always ensure that a memory mo dule is installed in the Primary slot (re d). If
not, then the system will fail to start. When installing two memory modules, please
ensure that they are the same size and ideally use the s ame type of RAM for b oth
memory slots. Th e maximu m s upported memory is 8GB combin ed .
TS-251/TS-451 TS-251A/TS-451A
60
7. Reattach the hard drive cag e t o th e NAS. Please ensure tha t it correctly plugs into the
slot.
8. Secure the hard drive cage by fastening the four inner screws (for the 4-bay NAS,
please fasten the two additional top screws.) Then reattach the case cover of the NAS
by gently sliding it back together.
9. Fasten the two/four screws onto the rear of the NAS.
10. Reinsert your hard drives to the NAS.
11. Connect the power adaptor and cables back to the NAS.
12. To check that the memory module is reco g nized by the NAS, power up the NAS and
login the web interface as an administrator. Go to “System Status”>“System
Information” and check the total memory in “Hardware Information”.
5.8 IS-453S
1. Loosen the four screws on the bottom and the two screws on the rear panel of the NAS
with a Phillips screwdriver and lift the bottom off.
61
2. Pull the retentio n clips on e a ch side so t hat the modu le tilts up for easy removal.
Remove installed memory mod ules.
Note: Always ensure that a memory module is install ed in the primary slot that is
on the top (marked with “DIMM1”.) If not, then the system will fail to start. The
maximum supported memory is 8GB combined.
3. Slide the memory module to the slot at a 45-degree angle (approxim ately) and pr ess
the memory module down until it clips into place. Ensure the memory module sits
62
properly with th e clips in place.
4. Close the NAS bottom cover and fasten the screws (refer to Step 1 for screw positions.)
Reconnect the power and network cables to the NAS.
63
Chapter 6. Network Expansion Card Installation
Warning:
The following instructions should only be performed by an authorized and trained
technician.
Strictly adhere to the instructions to install a network expansion card on the NAS.
Failure to do so c ould result in injury to human body or death.
Some NAS models provide expansion slots for network expansion. Insert an extra network
expansion card (optional purchase) to the motherboard of the NAS to increase the network
bandwidth. Refer to the compatibility list at: http://qnap.com/compatibility
Note: Wake-on-LAN (WoL) is not supported by network expansion cards.
6.1 TVS-463, TS-531P, TS-531X, TVS-663, TS-831X, TVS-863, TS-563, TS-879
Pro, TS-1079 Pro, TS-463U, TS-463U-RP
Refer to the compatibility table below for brack et and network card compatibility. For NAS,
network card, and bracket co m patibility, go to http://qnap.com/compatibility.
Bracket A Bracket B Bracket C
64
Network Expansion Card Compatibility
Bracket A
SP-BRACKET-10G-T
(X520-T2)
Intel® Ethernet Server Adapter X520-T2(E10G42B)
Bracket B
SP-BRACKET-10G-X520SR2
(X520-SR2/X520-DA2)
1. Intel® Ethernet Server Adapter
X520-SR2(E10G42BFSR)
2. Intel® Ethernet Server Adapter
X520-DA2(E10G42BTDA)
Bracket C
SP-BRACKET-10G-EMU
(Emulex)
1. Emulex OneConnect 10GbE Network Adapters, SFP+
Direct attach copper (OCe11102-NX, OCe14102-NX)
2. Emulex OneConnect 10GbE Network Adapters, Short
reach optical (OCe11102-NM)
3. Emulex OneConnect 10GbE Network Adapters, SFP+
Direct attach copper (OCe11102-IX)
4. Emulex OneConnect 10GbE Network Adapters, Short
reach optical (OCe11102-IM)
1. Turn off the NAS. Disconnect the power adaptor, network cable(s), and any other
connectors or cables from the NAS.
2. Before installing the network expansion card, put on an antistatic wrist strap to prevent
electrostatic discharge. The crocodile clip should be connected to the ground.
3. Loosen the screws on the rear of the NAS.
65
4. Remove the case cover of the NAS gently.
For TVS-463 only: Unscrew and remove the power supply unit.
5. Loosen the screws and remove the expansion slot cover.
66
6. Grasp the edge of the network exp ansion card. Ali gn the notch on the gol d edge of the
card with the notch i n the PCIe s lot. Insert t he network e xpansion car d to the PCI e slot
until it cannot go any further.
7. Fasten the screws.
67
8. Close the case cover and fasten the screws. Connect th e power adaptor and cables to
the NAS.
9. To check th at t he ne tw or k ex pansi on is rec ogni z ed b y the NA S, power up t he NA S and
login the web interface as an administrator. Go to “System
Administration”>“Network”>“TCP/IP” and check the total number of network
interfaces.
6.2 TS-1635
The TS-1635 provides a PCIe 2.0 x2 expansion slot so that users may choose to install a
network expansion card for added network performance.
To do so, follow the below steps:
1. T urn off the NAS. Disconnect power cord(s), network cable(s), and any other cables
attached to the devi ce .
2. Before opening the NAS, wear an antistatic wrist strap and connect the crocodile
clamp to ground to prevent electrostatic discharge from damaging equipment.
3. Loosen the screws on the back of the NAS that are connecting the case cover to the
case.
68
4. Gently remove case cover from case.
5. Loosen the screw of the top full-sized PCIe bracket. Remove bracket.
69
6. Hold the network ca rd by grasping the edge s. Align the no t ch o n the ne twor k ca rd
to the break in the PCIe slot. Fully insert the network expansion card to the
expansion slot.
70
7. Fasten screw to lock in card.
8. Close the case cov er and fasten the screws. Connect the power adaptor and cables
to the NAS.
9. To verify tha t the network expansion card has been installed correctly and is being
71
recognized by the operating system, log into QTS as administrator and go to
“Control Panel” > “System Settings” > “System Status” > “Network Status” and
check for total number of network interfaces.
6.3 TVS-473, TVS-673, TV S-873
Note:
1. TVS-473 uses low-profile PCIe bracket.
3. TVS-673 and TVS-873 use full height PCIe bracket.
1. T urn off the NAS. Disconnect power cord(s), network cable(s), and any other cables
attached to the device.
2. Before opening the NAS, wear an antistatic wrist strap and connect the crocodile
clamp to ground to prevent electrostatic discharge from damaging equipment.
3. Loosen and remove the screws on the back of the NAS that are connecting the case
cover to the case.
4. Gently remove case cover from case.
72
5. Loosen and remove the 3 screws on the back of the PSU.
6. Loosen and remove the remaining 2 screws conn ecting the PSU to the case.
73
7. Position the PSU so that a screw driver can access the screw of the PCIe bracket.
8. Loosen and remove the screw of the PCIe bracket. Remove bracket.
9. Hold the network expansion card by grasping the edges. Align the notch on the
74
network expansion card to the break in the PCIe slot. Fully insert the network
expansion card to the expansion slot.
10. Fasten screw to lock in card.
11. Place PSU back to its original position and fasten the 5 screws that were removed in
steps 6 and 7.
12. Close the case co ver and fasten the scre ws. Connect the power adaptor and cables
to the NAS.
13. To verify that the network expansion card has been installed correctly and is being
recognized by the operating system, log into QTS as administrator and go to
“Control Panel” > “System Settings” > “System Status” > “Network Status” and
check for the total number of network interfaces.
6.4 TS-431XU, TS-463U, TS-463U-RP, TVS-471 Series
1. Turn off the NAS. Disconnect the power adaptor, network cable(s), and any other
connectors or cables from the NAS.
2. Before installing the network expansion card, put on an antistatic wrist strap to
prevent electro static discharge. The crocodile clip should be connected to the ground.
75
3. Loosen all the screws on the top of the NAS as shown in the illustration.
4. Remove the top cover in both hands.
5. Loosen the screws as shown in the illustration.
6. Grasp the metal edge of the riser card module. Remove the module gently.
76
7. Remove the network expansion card/bracket.
a. For TS-463 U and TS-463U-RP, loosen the sc rew and remove the network
expansion card.
b. For TVS-471U, loose the screw and remove the bracket
77
8. Insert the new network expansion card to the riser card module until it cannot go a ny
further. Then fasten the scr e w.
9. Align the notch on the gold edge of the riser card with the notch in the PCIe slot. Insert
the riser card module to the PCIe slot until it cannot go any further.
78
10. Fasten the screws. Close the case cover and fasten the screws.
11. Connect the power adaptor and cables to the NAS.
12. To check that the network expansion is recognized by the NAS, power up the NAS and
login the web interface as an administrator. Go to “System Administration” > “Network”
> “TCP/IP” and check the total number of network interfaces.
6.5 TS-831XU, TS-863U, TS-863U-RP, TS-1231XU, TS-1263U, TS-1263U-RP
Series
1. Turn off the NAS. Disconnect the power adaptor, network cable(s), and any other
connectors or cables from the NAS.
2. Before installing the network exp ansion card, put on an antistatic wrist s t rap to
79
prevent electro static discharge. The crocodile clip should be connected to the ground .
3. Loosen the two screws on the rear of the NAS.
4. Hold the notch at the edge of the top cover. Remove the top cover in both hands.
5. Loosen the screw and remove the expansion slot cover.
6. Grasp the edge of the expansion card. Align the notch on the gold edge of the card with
the notch in the PCIe slot. Insert the network expansion card to the PCIe slot until it
cannot go any further.
80
7. Fasten the screws.
8. Close the case cover a nd fasten t he screws. Connect the powe r adaptor and cabl es to
the NAS.
9. To check that the network expansion is recognized by the NAS, power up the NAS and
login the web interface as an administrator. Go to “System Administration” > “Network”
> “TCP/IP” and check the total number of network interfaces.
81
Chapter 7. Install and Hot-swap Hard Drives
Caution:
Before starting, please ensure that you turn off the NAS, disconnect the power
adaptor, network cable(s), and also remove any other device/cable that is attached to
the NAS.
Please ensure that you wear an antistatic wrist strap during the entire process to
prevent electrostatic discharge. The crocodile cl ip should be connected to the gro und.
7.1 Install Hard Drives
Follow the below steps to ins tall hard drives on the N AS.
7.1.1. TS-x51, TS-x51A, TVS-x63, TS-563, TS-x53 Pro, TS-651, TS-831X,
TS-851, TS-531X, TS-531P, TS-x53A, TS-x31, TS-x31+, TS-x31P, TS-431U,
TS-x31XU, TS-451U, TS-x53U, TS-x63U
1. Lift th e hard drive lever a nd pull th e tray out.
82
2. Install the HDDs
a. For 3.5” HDDs, secure the four screws in the back of the hard drive tray.
b. For 2.5” HDDs, follow the signs which are marked on the tray then secure the
three screws in the ba ck of the hard drive tray
3. Insert the hard drive tra ys into the NAS all the way to the rear and push the lever back
until you hear a click.
83
7.1.2. TS-1635
1. Remove hard drive tray from NAS:
i. Push the blue lock switch on the tray down to the unl oc k position.
ii. Push the button below the blue switch to release the lever.
iii. Pull out tray using lever.
2. Install HDD/SDD onto tray.
a. 3.5” HDD:
i. Remove the fastening panels from the sides of the drive tray.
84
ii. Place hard drive onto tray so that the side holes of the tray are aligned with the side
holes of the harddrive.
iii. Reinsert fastenin g panels to lo ck drive to tray.
b. 2.5” HDD/SSD:
i. Remove the fastening panels from the sides of the drive tray.
ii. Place hard drive onto tray so that the bottom holes of the tray are aligned with the
bottom holes of the harddrive.
iii. Reinsert fastenin g panels to lo ck drive to tray.
85
3. Load tray back into drive bay.
i. Insert the drive tray into the NAS.Verify that the tray is correctly oriented (top of HDD
facing right) and fully pushed in.
ii. Close the latch, and lock the switch.
7.1.3. TS-453Bmini, TS-453Mini
1. Remove the case cover. Op en and remove the hard drive tray.
86
2. Install the H DD:
a. For 3.5” HDDs, remove both brackets (pinch the end marked “pull” to pull and
separate the bracket) from the tray. Place the hard drive on the tray and clip-in
both brackets.
87
b. F or 2.5 ” HDDs/S SDs , only r emo ve the b r acke t next to the 2.5” screw hole s (they
are marked on the bottom of the tray.) Secure the three screws in the back of the
hard dr ive tray.
3. Insert the hard drive tray into the Turbo NAS all the way to the bottom and close the
case cover.
88
7.1.4. TVS-473, TV S-6 73, TV S-873
1. Remove hard drive tray from NAS:
i. Push the lock switch on the tray down to the unlock position.
89
ii. Push the button below the blue switch to release the lever.
iii. Pull out tray us ing lever.
2. Install HDD/SDD onto tray.
a. 3.5” HDD:
i. Remove the fastening panels from the sides of the drive tray.
ii. Place hard drive onto tray so that the bottom holes of the tray are aligned with
the bottom holes of the harddrive.
iii. Reinsert fastening panels to lock drive to tray.
90
b. 2.5” HDD/SSD:
i. Insert 2.5” drive onto tray so that HDD /SSD connecto r i s p e r fectly aligned wi th the
opening at e nd of the tray.
ii. Secure the three screws in the back of th e hard drive tray.
91
3. Load tray back into drive bay.
i. Insert the drive tray into the NAS. Verify that the tray is correctly oriented (top of
HDD facing r i g ht) and fully pushed in.
ii. Close the latch, and lock the switch.
7.1.5. TS-112P, TS-2 12P an d TS-251C
1. Loosen the screws on the rear (top and bottom) of the NAS. R emov e the case cover of
the NAS by sliding it apart (see the underside of the NAS for visual indicators of the NAS
case being locked/unlocked.)
92
2. Install the hard drives:
a. For TS-112P: Place the hard drive in the hard drive cradle and slide it forward to
lock it into the connector. Secure the screws on the slides of the hard drive.
b. For TS-212P and TS-251C: Place the first hard drive in the hard drive cradle an d
slide it forward to look it into the connector. Place the second har d drive on top of
the first hard drive and secure the screws on the slides of both hard drives.
Connect the SATA cable and power cable to the connectors as shown in the
picture.
93
3. After ins talling the hard drives, cover the NAS with the case cover and fasten the round
head screws. Then, place the NAS vertically on the stands.
7.1.6. TAS-168, TAS-268, TS-128, TS-228
1. Remove the hand screw and the top cover.
94
2. Put the hard drive in the hard drive cradle and slide it forwards to lock it into the SATA
connector. Clip in both brackets, slide the bracket into the hole in point 2 before pressing
the bracket towards the HDD (for the TAS-268, repeat th e s ame s tep for the second
drive.)
3. Align point a on the case cover with point b on the front of t he NAS (s ee figur e below).
Push forward the case cover (step 2) and fasten the toolless sc rew to secure the case
cover.
95
96
7.1.7. IS-453S
1. Remove all four screws from the front panel.
2. Remove the drive tray.
3. Attach the drive to the tray and secure the four screws in the back of the drive tray.
97
4. Insert the drive tray into th e NAS all t he way to the end .
5. Repeat Step 2 to 4 to install the remaining drives. Pleas e f o llow t he HDD Sequence
shown in Step 2 to do so.
98
6. Close the front panel and fasten the screws.
99
7.2 Hot-swap Hard Drive s
QNAP NAS is compatible with 2.5-inch/3.5-inch SA TA hard disk drives from major hard disk
brands. For the updated hard drive compatibility list, please visit http://www.qnap.com.
Caution:
QNAP disclaims any responsibility for product damage/malfunction or data
loss/recovery due to misuse or improper installation of hard disks in any occasions for
any reasons.
Note that if a hard drive (new or used) which has never been installed on the NAS
before it is installed, the hard drive will be formatted and partitioned automatically and
all the disk data will be cleared .
System Support
s
3.5-inch
SATA
Hard
Drives
Support
s
2.5-inch
SATA
Hard
Drives
Suppor
ts 2.5”
SATA
SSD
Supports
M.2 SATA
SSD
Supports
Hot-swappa
ble Hard
Drives
(RAID 1 or
above only)
TS-112P, TS-212P,
TS-251C
✔
TAS-168, TAS-268,
TS-128, TS-228
✔
TS-131,TS-131P ✔ ✔ ✔
TVS-473, TVS-673,
TVS-873
✔ ✔ ✔ ✔ (2280 &
2260)
✔
HS-210, HS-251,
HS-251+, TS-231,
TS-231+, TS-231P,
TS-251, TS-251+,
TS-251A, TS-431,
TS-431+,TS-431P,
TS-431U, TS-451,
TS-451+, TS-451A,
TS-651, TS-851,
TS-253 Pro, TS-453
Pro, TS-453S Pro,
✔ ✔ ✔ ✔
100
System Support
s
3.5-inch
SATA
Hard
Drives
Support
s
2.5-inch
SATA
Hard
Drives
Suppor
ts 2.5”
SATA
SSD
Supports
M.2 SATA
SSD
Supports
Hot-swappa
ble Hard
Drives
(RAID 1 or
above only)
TS-563, TS-653 Pro,
TS-853 Pro, TS-853S
Pro, TS-879 Pro,
TS-1079 Pro,
TS-879U-RP,
TS-1279U-RP,
TS-EC879U-RP,
TS-EC1279U-RP,
TS-1679U-RP,
TS-EC1679U-RP,
TS-451U, TS-453U,
TS-453U-RP, TS-853U,
TS-853U-RP,
TS-1253U,
TS-1253U-RP,
TS-870U-RP,
TS-1270U-RP,
TS-470/470 Pro,
TS-670/670 Pro,
TS-870/870 Pro,
TVS-463, TVS-663,
TS-831X, TVS-863,
TVS-863+,
TS-453Bmini,
TS-463U, TS-463U-RP,
TS-863U, TS-863U-RP,
TS-1263U,
TS-1263U-RP,
TS-531P, TS-253A,
TS-453A, TS-653A,
TS-853A, TS-x31XU
TS-451S, TS-453S ✔ ✔ ✔
101
System Support
s
3.5-inch
SATA
Hard
Drives
Support
s
2.5-inch
SATA
Hard
Drives
Suppor
ts 2.5”
SATA
SSD
Supports
M.2 SATA
SSD
Supports
Hot-swappa
ble Hard
Drives
(RAID 1 or
above only)
Pro, TS-853S Pro,
IS-453S, TVS-882S,
TVS-882ST
TVS-473, TVS-673,
TVS-873
✔ ✔ ✔ ✔ (2280,
2260)
✔
TBS-453A ✔ (2280,
2260, 2242)
The NAS supports hot-sw appi ng t h e har d dr i v es when 1 member drive crashes in RAID 1,
1–2 member drives crash in RAID 5 or RAID 6. Follow the steps below to hot-swap the hard
drive when a member drive fails in a RAID configuration.
1. Login the NAS and check the disk volume configuration in “Volume Management”.
2. The volume status should be “in degraded mode”.
3. Prepare a new hard drive to replace the failed one. The capacity of the new hard drive
should be the same as or larger than the failed hard drive.
4. Unplug the failed drive from t he NAS. Wait for about 20 seconds or until the server
beeps twice.
5. Remove the failed drive f r om the drive tray.
6. Install the new hard drive on the drive tray. Insert it to the NAS.
7. The server should beep 1.5 seconds twice.
8. Check the volume status on the web adminis tration page. The volume should be
rebuilding.
Warning: Users are strongly recommended to turn OFF the server before replacing
102
the hard drive to reduce the risk of electric shock.
103
Chapter 8. Install M.2 SSDs
8.1 M.2 SSD Heat Sink Installation
NAS models that support M.2 SSDs are packaged with M.2 SSD heat sinks. For reliable
operation, it is recommended that you install th e heat sinks ont o the SSD controller.
To inst all heat sink:
1. Locate the SSD controller on the M.2 SSD. Location of SSD controller varies by model.
Refer to SSD manufacturer for details.
2. Remove any existing stickers or labels on the controller.
3. Remove the release liner from bottom of the heat s in k.
4. Stick heat sink onto the controller. No thermal paste required.
104
8.2 M.2 SSD Installation
Some NAS models hav e a temperature sensor below the M.2 SSD. Do not attempt to bend
or remove the sensor.
8.2.1 TBS-453A
1. The system has four M.2 SSD slots that are located on the bottom of the system. The
storage capacity of the system ca n be upgr aded by adding M.2 S SD mo dules to vacant
M.2 SSD slots or by upgrading existing M.2 SSD modules. The following procedure
demonstrates how to add/repla ce M.2 S SD mo dules. To remove the bottom cover, first
remov e t he r ubber feet. Next , uns crew the fo ur scre ws ins tall ed o n the f our c orner s of
the bottom co v e r b y turning them counterclockwise.
105
2. TBS-453A supports 3 different sizes of M.2 SSD (2242, 2260, and 2280). Move and
fasten the riser screw to the appropriate location according your M.2 SSD size. Then
insert the M.2 SSD to the slot and secure it in place with the supplied screws.
3. Secure the bottom cover back to the system by installing the screws of four corners
(clockwise). Then put the rubber feet back as well.
8.2.2 TVS-473, TVS-673, TV S-873
106
1. Turn off the NAS. Disconnect power cord(s), network cable(s), and any other cables
attached to the devi ce .
2. Before opening the NAS, wear an antistatic wrist strap and connect the crocodile
clamp to ground to prevent electrostatic discharge from damaging equipment.
3. Loosen the screws on the back of the NAS that are connecting the case cover to the
case.
4. Remove case cover from case.
107
5. [Optional: for M.2 2260 SSD only] Insert and fasten riser screw.
6. Hold the M.2 SSD module by grasping its edges. Align the notch on the module with
the ridge in the M.2 sock et. Gently slide the memory module into the socket at a
15-degree angle. Ensure that the module is firmly inserted into slot. Do not force
the M.2 dri ve into socket.
108
7. Gently lower the memory module towards the motherboard until it sits on the riser
screw. While holding do wn the M .2 SS D in posit ion, inse rt mounti ng scr ew into the
riser screw, tightening as necessary to securely fasten the M.2 SSD in place. Do not
over tighten the screw.
8. Close the case cov er and fasten the screws. Connect the power adaptor and cables
to the NAS. Power on NA S.
9. To verify tha t the M.2 SSD has been installed correctly and is being recognized by
the oper ating system, log into QTS as administrator. Go to “Main Menu” > “Storage
Manager”> “Disks/VJBOD”. In the “NAS Host” secti on, check the status o f the M.2
SSD.
109
Chapter 9. RAID Recovery
The QNAP NAS supports RAID recovery when a healthy drive is unexpectedly removed from
a RAID or JBOD configuration. Even if a healthy drive is removed from a degraded RAID
1/5/6 configuration while attempting to hot-swap a faulty drive, the user can reinsert the
drive back into its or iginal position to recover the RAID. RAID recovery is also supported
when a healthy drive is unexpectedly removed from a RAID 0/JBOD configuration. Note
that RAID 10 does not support this feature.
When a healthy drive is unexpectedly removed from a RAID group, the status of the RAID
will change to “Not active”. To recover from a “Not active” status:
1. Re-insert all hard drives back into the NAS in its or iginal order. T his includ e s any bad
drive(s) that will need to be rep lac ed after recovery.
2. Log into QTS as administrator and go to “Control Panel” > “Storage Manager” >
“Storage Space”.
3. Double click on the affected Storage Pool to open the Storage Pool Management
window.
4. In the “Storage Pool Management” window, click on the “Manage” button and select
“Recover”.
The process will take approximately 60 seconds to complete. When recovery is completed,
the RAID group should be restored to its initial status.
See chart below for RAID status during this process.
Initial
Status
Status After Healthy
Drive is Removed
Status After Drive is
Re-Inserted and Storage
Pool is Recovered
RAID 0/JBOD Ready Not active Ready
RAID 1/5/6 Ready Degraded Rebuilding
RAID 1/5/6 Degraded Not active Degraded
The chart below describes the events of an error when using RAID 5.
RAID 5 (Minimu m 3 Disks)
QTS Standard
110
One drive
fails
Degrade d m o de (may
still read and write). Degraded mode (may still read and write).
One drive fails and ther e are b ad sector s
found in the other drive(s)
Read only
protect mode
(for
immediate
data backup
& hard drive
replacement)
.
RAID crash.
2 hard drives fail RAID
crash.
RAID crash.
The chart below describes the events of an error when using RAID 6.
RAID 6 (Minimum 4 Disks)
QTS Standard
One or two drives
drive fail
Degrade d m o de . (may still read
and write).
Degrade d m o de . (may still read
and write).
Two drives fail
and there are bad
sectors found in
the other drive(s)
Read only protect mode (for
immediate data backup & hard
drive replacement).
RAID crash.
3 hard drives fail RAID crash. RAID crash.
111
Chapter 10. Use the LCD Panel
This feature is only available for NAS models with LCD panels.
LCD Panel – QTS 4.3.0 and above
You can use the L CD pa nel to confi gure sys tem set tings a nd view s ystem inform ation. You
can use the “ENTER” and “SELECT ” butto ns nex t to the panel to navi gate thr ough t he LCD
menu.
After starting the NAS, you can see its name and firmware version appear on the panel.
N
A
S
5
F
4
D
E
3
4
.
3
.
0
(
2
0
1
6
0
7
0
3
)
After a few seconds, the panel will be automatically turned off. Then you can begin to
configure settings or view system information.
Viewing system IP address
1. Press “ENTER” or “SELECT” to turn on the panel.
2. Press “SELECT” to browse the NAS model name and the av ailable IP addresses (for
each network and thunderbolt interface).
This feature is particularly useful when the NAS is near you.
Viewing and configuring system settings
When the name and firmware version of the NAS appear on the panel, press “ENTER” for
two seconds to view the Main Menu, which will automatically disappear if no further actions
are performed in ten seconds.
There are eight options on the Main Menu:
1. TCP/IP
2. Physical disk
3. Volume
4. System
5. Shut down
6. Reboot
7. Password
8. Back
112
Press “SELECT” to go to the next option and “ENTER” to select an option.
TCP/IP
In TCP/IP, you can see the following options:
1. LAN IP Address
380
2. LAN Subnet Mask
3. LAN Gateway
4. LAN PRI. DNS
5. LAN SEC. DNS
(You can configure the above settings for every interface).
6. Enter Network Setti ngs
a. Network Settings – DHCP
i. Set up DHCP on LAN1 and LAN2.
b. Network Setti ngs – Static IP*
i. Press “SELECT” to switch to the next available option.
ii. Press “ENTER” to configure the selected option. The first digit will begin to
blink.
iii. Press “SELECT” to increment the selected digit, press “ENTER” to confirm the
value, and go to the next digit until all d igits are set.
iv. Repeat this procedure this for every setting you want to change.
c. Network Setti ngs – BACK
7. Back to Main Menu
* In this section, you can only configure IP address, subnet mask, gateway, and
DNS of LAN1 and LAN2.
Physical disk
In Physical disk, yo u can see the following options:
1. Disk Info
113
2. Back to Main Menu
Disk Info shows the temperature and the capacity of the hard drives.
D
i
s
k
:
1
T
e
m
p
:
5
0
°
C
S
i
z
e
:
2
3
2
G
B
Volume
This section shows the capacities of volumes and LUNs. You can view the name and
capacity of a volume/LUN. If there are mu lt ip le volumes/LUNs, press "Select " to view the
information of a specific volume/LUN.
D
a
t
a
V
o
l
1
7
5
0
G
B
L
U
N
_
0
1
0
0
G
B
System
This section shows the system temperature and the rotation speed of the system fan.
C
P
U
T
e
m
p
:
5
0
°
C
S
y
s
T
e
m
p
:
5
5
°
C
F
a
n
1
:
2
3
2
1
R
P
M
F
a
n
2
:
2
4
0
2
R
P
M
Shut down
You can use this option to turn off the NAS. Press "SELECT", select "Yes", and then press
"ENTER" to co nf i r m.
114
Reboot
Y ou can use this option to restart the NAS. Press "SELECT", select "Y es", and press "ENTER"
to confirm.
Password
The default password for the LCD panel is empty. If you want to change the password,
select "Yes" to continue.
C
h
a
n
g
e
P
a
s
s
w
o
r
d
Y
e
s
→
N
o
You can enter up to 8 digits for your password.
Press “SELECT” to increment the digit and press “ENTER” to add a new digit.
After inputtin g your desired password, press “ENTER ”.
When the cursor moves next to "OK", press “ENTER” to confirm the password.
N
e
w
P
a
s
s
w
o
r
d
:
2
3
4
→
O
K
Verify the passw ord t o confirm the chang es.
V
e
r
i
f
y
P
a
s
s
w
o
r
d
:
2
3
4
→
O
K
Back
Select this option to return to the Main Menu.
System Messages
When an e rror occurs, a message will appea r on the LCD panel. Pre ss “ENTER ” to view the
message and press “ENTER” again to go to the next message.
S
y
s
t
e
m
E
r
r
o
r
!
P
l
s
.
C
h
e
c
k
L
o
g
s
115
System Message Description
Sys. Fan Fai led The system fan has failed.
Sys. Overheat The system has overheated.
HDD Overheat A hard drive has overheated.
CPU Overheat The CPU has overheated.
Network Lost Bo th LAN 1 and LAN 2 are disconnected in failover or load balancing mode.
LAN1 Lost LAN 1 is disconnected.
LAN2 Lost LAN 2 is disconnected.
HDD Failure A hard drive has failed.
Vol1 Full T he disk volum e (1) is full.
NAS HDD Ejected A hard drive has been ejected from the NAS.
RX#3 HDD Ejected A hard drive has been ejected from t he expansion unit 3.
M.2 SSD Ejected A M.2 SSD has been ejected and may be defective as hot-plugging is not
supported for M.2 drives.
PCIe SSD Ejected A PCIe SSD has been ejected and may be defective as hot-plugging is n ot
supported for PCIe devices.
Vol1 Degraded The disk volume (1) is in degraded mode.
Vol1 U nmounted The disk volume (1) is unmounted.
Vol1 Non ac tivate The disk volume (1) is inactive.
System startup
S
Y
S
T
E
M
B
O
O
T
I
N
G
>
>
>
There are several phases in the system startup process:
- System Booting: BIOS and hardware initialization, and system booting (no actions
need to be performed)
116
- Loading Driver: Loading QTS and its drivers(no actions need to be performed)
- Mount Volume: Prepare volumes(no actions need to be performed)
- Starting Servi ce: Starting NAS s ystem services (no actions need to be performed).
Note that applications start only after the system finishes booting.
For TVS-x82 Series, the L CD panel displa ys additional booting information after you power
on the NAS:
B
I
O
S
X
X
X
X
X
X
X
C
h
e
c
k
i
n
g
M
e
m
o
r
y
- BIOS xxxxx – xxxx is the BIOS version, which ca n be used for technical support to
help identify and resolve issue s.
- - Startup phases:
o Checking Memory – The system checks the installed memory.
o Powering up all disks – Power up all disks sequentially.
o Hardware initialization – Initialize additional hardware components, such as PCIe
SSD, Graphic card, Thunderbolt adapter, etc.
o Booting - Boot from the DOM. If the startup stops at this step, the DOM may be
defective. Please seek technical support.
o Starting System – Starting QTS. If the startup stops at this step, the QTS
installation may have encountered problems . Please seek technical support.
- The remaining startup phases are the same as those of other NAS models
LCD Panel – QTS 4.2.x and below
Refer to QTS 4.2.x User Manual for details.
117
Chapter 11. Install Power Supply Unit
Note:
This section applies to rackmount NAS models only.
The power supply units of TS-879U-RP and TS-EC879U-RP should only be replaced by an
authoriz e d a nd trained te c hnician.
11.1 1U Turbo N AS with Hot-swappable PSU
Note: The following instruction s should only be performed by an authorized and trained
technician.
To install a redundant power supply unit to the 1U Turbo NAS, follow the steps below.
1. Turn off the NAS.
2. Remove the screw and du mmy plate.
3. Insert the power supply unit and push it to the end.
4. Fasten the screw tightly.
118
5. Turn on the NAS.
Note: To re pla ce a f ailed p ower s upp ly uni t, tur n off the N A S. Then r emo ve the fai led uni t
safely and repeat steps 3-5 above to install a new power supply unit.
11.2 2U/3U Turbo NAS (TS-831XU-RP, TS-1231XU-RP, TS-853U-RP,
TS-1253U-RP only)
Note: The following inst ructions should only be performed by an authorized and trained
technician.
To replace a failed power supply unit, follow the steps below.
1. Turn off the NAS.
2. Hold the black handler and press and hold the green button firmly.
3. Unplug the failed power supply.
119
4. Plug in a new power supply to the NAS.
5. Turn on the NAS.
Enable warning alert for redundant power supply on the web-based interface:
If two power supply units (PSU) have been installed on the NAS and connected to the power
sockets, both PSU will supply the power to the NAS (applied to 1U and 2U models). Users
can enable redundant power supply mode in “System Administration” > “Hardware” to
receive warning alert for the redundant power supply. The NAS will beep and record the
error messages in “System Logs” when the PSU is plugged out or fails.
If only one PSU is installe d on the NAS, users are suggested NOT to enable this option.
120
* This function is disabled by default.
WARNING: RISK OF ELECTRIC SHOCK
The connectors on the back panel (bracketed parts below) contain high voltage. Do NOT
touch these parts to avoid the risk of electric shock to the maintenance operator.
121
Technical Support
QNAP provides dedicated online support and customer service via instant mess eng er.
Online Support: http://qnap.com/support
Forum: http://forum.qnap.com
Technical Support in the USA and Canada:
Online Support: http://qnap.com/support
TEL: +1-909-595-2782 #3
Address: 168 University Parkway, Pomona CA 91768
Service Hours: 06:00-18:00 (GMT- 08:00 Pacific Time, Monday to Friday)
122
GNU GENERAL PUBLIC LICENSE
Version 3, 29 June 2007
Copyright © 2007 Free Software Foundation, Inc. <http://fs f.org/>
Everyone i s permitted to copy and distribute verbati m copies of this license docu ment, but
changing it is not a llowed.
Preamble
The GNU General Public License is a free, c opy left license for s of tware and other kinds of
works.
The licenses for most software and other practical works are designed to take away your
freedom to share and change the works. By contrast, the GNU General Public License is
intended to guarantee your freedom to share and change all versions of a program--to
make sure it remains fre e software for all its users. W e, the Free Software F oundation, use
the GNU General Public License for most of our software; it applies also to any other work
released this way by its authors. You can apply it to your programs, too.
When we speak of free software, we are referring to freedom, not price. Our General Public
Licenses are designed to make sure that you have the freedom to distribute copies of free
software (and charge for them if you wish), that you receive source code or can get it if you
want it, that you can change the software or use pieces of it in new free programs, and that
you know you can do these things.
To protect your rights, we need to prevent others from denying you these rights or asking
you to surre nder the rights. Th e r e fore, you have certa in responsibilities if you d istribute
copies of the software, or if you modify it: responsibilities to respect the freedom of others.
For example, if you distribute copies of such a program, whether gratis or for a fee, you
must pass on to the recipients the same freedoms that you received. You must make sure
that they , too, receive or can get the source code. And you must show them these terms so
they know their rights.
Developers that use the GNU GPL protect your rights with two steps: (1) assert copyright
on the software, and (2) offer you this License giving you legal permission to copy,
distribute and/or modify it.
123
For the developers' and authors' protection, the GPL clearly explains that there is no
warranty for this free software. For both users' and authors' sake, the GPL requires that
modified versions be marked as changed, so that their problems will not be attributed
erroneously to authors of previous versions.
Some devices are designed to deny users access to install or run modified versions of the
software inside them, although the manufacturer can do so. This is fundamentally
incompatible wit h the aim of protecting u s er s ' freedom t o c hange the software. The
systematic pattern of such abuse occurs in the area of products for individuals to use, which
is precisely where i t is most unacceptable. Therefore, we have designed this version of the
GPL to prohibit the practice for those products. If such problems arise substantially in other
domains, we stand ready to extend this provision to those domains in future versions of the
GPL, as needed to protect th e freedom of users.
Finally, every program is threatened constan tly by software patents. States should not
allow patents to restrict development and use of software on general-purpose computers,
but in those that do, we wish to avoid the special danger that patents applied to a free
program could make it effectively proprietary . T o prevent this, the GPL assures that patents
cannot be used to render the program non-free.
The precise terms and conditions for copying, distribution and modification follow.
TERMS AND CONDITIONS
0. Definitions.
“This License” refers to version 3 of the GNU General Public License.
“Copyright” also means copyright-like laws that apply to other kinds of works, such as
semiconductor masks.
“The Program” refers to any co pyrightable work licensed under this License. Each licensee
is addressed as “you”. “Licensees” and “recipients” may be individuals or organizations.
T o “modify” a work means to copy from or adapt all or part of the work in a fashion requiring
copyright permi ssion, other than th e making o f an exact co py. The resul ting work is called
a “modified version” of the earlier work or a work “based on” the earlier work.
A “covered work” means either the unmodified Program or a work based on the Program.
124
To “propagate” a wor k mea ns to do anyt hing wi th it tha t, wi thout pe rmi ssion, wo uld mak e
you directly or secondarily liable for infringe m e nt under applicab le copyright law, except
executing it on a computer or modifying a private copy. Propagation includes copying,
distribu tion (w ith or without modification), making available to the public, a nd in some
countries other a ctivities as well.
To “convey” a work means any kind of propagation that enables other parties to make or
receive copies. Mere interaction with a user through a comp uter net work, wi th no t r ansfer
of a copy, is not conveying .
An interactive user interface displays “Appropriate Legal Notices” to the extent that it
includes a convenient and prominently visible feature that (1) displays an appropriate
copyright notice, and (2) tells the user that there is no warranty for the work (except to the
extent that w a r ranties are provided), that licensee s may convey the work under this
License, and how to view a copy of this License. If the interface presents a list of user
commands or options, such as a menu, a prominent item in the list meets this criterion.
1. Source Code.
The “source code” for a work means the preferred form of the work for making
modifications to it. “Object code” means any non-source form of a work.
A “Standard Interface” means an interface that either is an official standard defined by a
recognized standards body, or, in the case of interfaces specified for a particular
programming language, one that is widely used among developers working in that
language.
The “System Libraries” of an executable work include anything, other than the work as a
whole, t hat (a) i s includ ed in the normal form of packagi ng a Majo r Compone nt, but w hich
is not part of that Major Component, and (b) serves only to enable use of the work with that
Major Component, or to implement a Standard Interface for which an implementation is
avail able to the public in source code form. A “Major Component”, in this context, means a
major essential comp o nent (kernel, window system, and so on) of the specific operating
system (if any) on which the executable work runs, or a compiler used to produce the work,
or an object code interpreter used to run it.
The “Corresponding Source” for a work in object code form means all the source code
needed to generate, install, and (for an executable work) run the object code and to modify
125
the work, including scripts to control those activities. However, it does not include the
work's System Libraries, or general-purpose tools or generally available free programs
which are used unmodified in performing those activities but which are not part of the work.
For example, Corresponding Source includes interface definition files associated with
source files for the work, and the source code for shared libraries and d ynamically linked
subprograms that the work is specifically designed to require, such as by intimate data
communication or control flow between those subprograms and other parts of the work.
The Corresponding Source need not include anything that users can regenerate
automatically from other parts of the Corresponding Source.
The Corresponding Source for a work in source code form is that same work.
2. Basic Permissions.
All rights gr anted under t his License are gr anted for t he term of cop yright on the Program,
and are irrevocable provided the stated conditions are met. This License explicitly affirms
your unlimited permission to run the unmodified Program. The output from running a
covered work is covered by this License only if the output, given its content, constitutes a
covered work. This License acknowledges your rights of fair use or other equivalent , as
provided by copyright law.
You may make, run and propagate covered works that you do not convey, without
conditions so long as your license otherwise remains in f o rce. You may convey covered
works to others for the sole purpose of having them make modifications exclusively for you,
or provide you with facilities for running those works, provided that you comply with the
terms of this License in conveying all material for which you do not control copyright. Those
thus making or running the covered works for you must do so exclusively on your behalf,
under your direction and control, on terms that prohibit them from making any copies of
your copyrighted material outside their relations hip with you.
Conveying under any other circumstances is permitted solely under the conditions stated
below. Sublicensing is not allowed; section 10 makes it unnecessary.
3. Protecting Users' Legal Rights From Anti-Circumvention Law.
No covered work shall be deemed part of an effective technological measure under any
applicable law fulfilling obligations under article 11 of the WIPO copyright treaty adopted on
20 December 1996, or similar laws prohibiting or restricting circumvention of such
measures.
126
When you convey a covered work, you waive any legal power to forbid circumvention of
technological measures to the extent such circumvention is effected by exercising rights
under this License with respect to the covered work, and you disclaim any intention to limit
operation or modification of the work as a means of enforcing, against the work's users,
your or third parties' legal rights to forbid circumvention of technological measures.
4. Conveying Verbatim Copies.
You may convey verbatim copies of the Program's source code as you receive it, in any
medium, provided that you conspicuously and appropriately publish on each copy an
appropriate copyright notice; keep intact all notices stating that this License an d any
non-permissive terms added in accord with section 7 apply to the code; keep intact all
notices of the absence of any warr anty; and give all recipients a copy of this License along
with the Prog ram.
You may charge any price or no price for each copy that you conv ey, and you may offer
support or warranty protection for a fee.
5. Conveying Modified Source Versions.
You may convey a work based on t he Program, or the modifications to produce it from the
Program, in the form of source code under the terms of section 4, provided that you also
meet all of these cond it ions:
a) The work must carry prominent notices stating that you modified it, and giving a relevant
date.
b) The work mus t carry prominent notices stating that it is rel eased under this License and
any conditions added under section 7. This requirement modifies the requirement in section
4 to “keep intact all not ices”.
c) You must license the entire work, as a whole, under this Lic ense to anyone who comes
into possession of a copy. This License will theref o re apply, along with any applica ble
section 7 additional terms, to the whole of the work, and all its parts, regardless of how they
are packaged. This Lice nse gives no permission to license the work in any other w ay, but it
does not invalidate such permission if you have separately received it.
d) If the work has interactive user interfaces, each must display Appropriate Legal Notices;
however, if the Program has interactive interfaces that do not display Appropriate Legal
Notices, your work need not make them do so.
A compilation of a covered work with other separate and independent works, which are not
by their nature extensions of the covered work, and which are not combined with it such as
127
to form a larger program, in or on a volume of a storage or distribution medium, is called an
“aggregate” if the compilation and its resulting copyright are not used to limit the access or
legal rights of the compilation's users beyond what the individual works permit. Inclusion of
a covered work in an aggregate does not cause this License to apply to the other parts of
the aggregate.
6. Conveying Non-Source Forms.
You may convey a covered work in object code form under the terms of sections 4 and 5,
provided that you also co nvey t he machine-readable Corresponding Source under the
terms of this License, in one of these ways:
a) Convey the object code in, or embodied in, a physical product (including a physical
distribution medium), accompanied by the Corresponding Source fixed on a durable
physical medium customarily used for software interchange.
b) Convey the object code in, or embodied in, a physical product (including a physical
distribution medium), accompanied by a written offer, valid for at least three years and
valid for as long as you offer spare parts or customer support for that product model, to give
anyone who possesses the object code either (1) a copy of the Corresponding Source for all
the software in the product that is covered by this License, on a durable physical medium
customarily used for software interchange, for a price no more than your reasonable cost of
physically performing this conveying of source, or (2) access to copy the Corresponding
Source from a network server at no charge.
c) Convey individual copies of the object code with a copy of the written offer to provide the
Corresponding Source. This alternative is allowed only occasionally and noncommercially,
and only if you received the object code with such an offer, in accord with subsection 6b.
d) Convey the object code by offering access from a designated place (gratis or for a
charge), and offer equivalent access to the Corresponding Source in the same way through
the same place at no further charge. You need not require recipients to copy the
Corresponding Source along with the object code . If the place to cop y the o bject co de is a
network server, the Corresponding Source may be on a different server (operated by you or
a third party) that s upports e quivalent copy in g facilit ie s, provide d you maintain clear
directions next to the object code saying where to find the Corresponding Source.
Regardless of what server hosts the Corresponding Source, you remain obligated to ensure
that it is available for as long as needed to satisfy these requirements.
e) Convey the object code using peer-to-peer transmission, provided you inform other
peers where the object code and Corresponding Source of the work are being offered to the
general public at no charge under subsection 6d.
A separable portion of the object code, whose source code is excluded from the
128
Corresponding Source as a System Library, need not be included in conveying the object
code work.
A “User Product” is either (1) a “consumer product”, which means any tangible personal
property which is normally used for personal, family, or household purposes, or (2)
anything designed or sold for incorporation into a dwelling. In determining whether a
product is a consume r product, doubtful cases shal l be resolved in fa vor of co verage. F or a
particular product received by a particular user, “normally used” refers to a typical or
common use of that class of product, regardless of the status of the particular user or of the
way in which the particular user actually uses, or expects or is expected to use, the product.
A product is a consumer product regardless of whether the product has substantial
commercial, industrial or non-consumer uses, unless such uses represent the only
significant mode of use of the product.
“Installation Information” for a User Product means any methods, procedures,
authorization keys, or other information required to install and execute modified versions of
a covered work in that User Product from a modified version of its Corresponding Source.
The information must suffice to ensure that the continued functioning of the mod ified
object code is in no case prevented or interfered with solely because modification has been
made.
If you convey an object code work under this section in, or with, or specifically for us e in,
a User Product, and the conveying occurs as part of a transaction in which the right of
possession and use of the User Product is transfe rred to the reci pient in perpetuity or for a
fixed term (regardless of how the transaction is characterized), the Corresponding Source
conveyed under this section must be accompanied by the Installation Information. But this
requireme nt doe s not apply if neither you nor any third pa rty retain s the ability to install
modified object c ode on the User Product (for example, the work has been ins talled in
ROM).
The requirement t o provide Installation Inf ormation does n ot include a requirement to
continue to provide support service, warranty , or updates for a work that has been modified
or installed by the recipient, or for the User Product in which it has been modified or
installed. Access to a network may be denied when the modification itself materially and
adversely affects the operation of the network or violates the rules and protocols for
communication across the network.
Corresponding Source conveyed, and Installation Information provided, in accord with this
129
section must be in a format that is publicly documented (and with an implementation
available to the public in source code form), and must require no special password or key
for unpacking, reading or copying.
7. Additional Terms.
“Additional permissions” are terms that supplement the terms of this License by making
exceptions from one or more of its conditions. Additional permissions that are applicable to
the entire Program shall be treated as th o ugh they were included in this License, to the
extent that they are valid under applicable law . If additional permissions apply only to part
of the Program, that part may be used separately under those permissions, but the entire
Program remains governed by this License without regard to the additional permissions.
When you conv ey a copy of a covered work, yo u may at your option remove an y additional
permissions from that copy, or from an y part of it. (Additional permissions may be written
to require their own removal in certain cases when you modify the work.) You may place
additional permissions on material, added by you to a cove red work, for which you have or
can give appropriate copyright permission.
Notwithstanding any other provision of this License, for material you add to a covered work,
you may (if authorized by the copyright holders of that material) supplement the terms of
this License with terms:
a) Disclaiming warranty or limiting liability differently from the terms of sections 15 and 16
of this License; or
b) Requiring preservation of specified reasonable legal notices or author attributions in that
material or in the Appropriate Legal Notices displayed by works containing it; or
c) Prohibiting misrepresent at ion of the origin of that material, or requiring that modified
versions of such material be marked in reasonable ways as different from the original
version; or
d) Limiting the use for publicity purposes of names of licensors or authors of the material;
or
e) Declining to grant rights under trademark law for use of some trade names, trademarks,
or service marks; or
f) Requiring indemnification of licensors and authors of that material by anyone who
conveys the material (or modified versions of it) with contractual assumptions of liability to
the recipient, for an y li abilit y that these contractual assumptio ns dire ctly im pose on those
licensors and authors.
All other non-permissive additional terms are considered “further restrictions” within th e
130
meaning of section 10. If the Program as you received it, or any part of it, contains a notice
stating that it is governed by this License along with a term that is a further restriction, you
may remove that term. If a license document contain s a further rest riction but permits
relicensing or conveying under this License, you may add to a covered work material
governed by the terms of that license document, provided that the further restriction does
not survive such relicensing or conveying.
If you add terms to a covered work in accord with this section, you must place, in the
relevant source files, a statement of the additional terms that apply to those files, or a
notice indicating where t o find the applicable ter m s.
Additional terms, permissive or non-permissive, may be stated in the form of a separately
written license, or stated as exceptions ; the above requirements apply either way.
8. Termination.
You may not propagate or modify a cove red work ex cept as expressly provided under this
License. Any attempt otherwise to propagate or modify it is void, and will automatically
terminate your rights under this License (including any patent licenses granted under the
third paragraph of section 11).
However, if you cease all violation of this License, then your license from a particular
copyright holder is reinstated (a) provisionally, unless and until the copyright holder
explicitly and finally terminates you r license, a nd (b) pe rma nently, if the copyright ho lder
fails to notify you of the violation by some reasonable means prior to 60 days after the
cessation.
Moreover, your license from a particular copyright holder is reinstated permanently if the
copyright holder n otifies you o f the violatio n by some r e asonable me ans, this is the f ir st
time you have received notice of violation of this License (for any work) from that copyright
holder, and you cure the violation prior to 30 days after your receipt of the notice.
Termination of your rights under this section does not terminate the licenses of parties who
have received copies or rights from you under this License. If your rights have been
terminated and not permanently reinstated, you do not qualif y to receive new licenses for
the same material und er section 10.
9. Acceptance Not Required for Having Copies.
Y ou are not required to accept this License in order to receive or run a copy of the Program.
131
Ancillary propagation of a covered work occurring solely as a consequence of using
peer-to-peer transmission to receive a copy likewise does not require acceptance. However,
nothing ot her than thi s License gr ants you permission to propagate or modify any covered
work. These actions infringe copyright if you do not accept this License. Therefore, by
modifying or propagating a covered work, you indicate your acceptance of this License to
do so.
10. Automatic Licensing of Downstream Recipients.
Each time you convey a covered work, the recipient automatically receives a license from
the original licensors, to run, modify and propagate that work, subject to this License. You
are not responsible for enforcing compliance by third parties with this License.
An “entity transaction” is a transaction transferring control of an organization, or
substantially all assets of one, or subdividing an organization, or merging organizations. If
propagation of a covered work results from an entity transaction, each party to that
transaction who receives a copy of the work also receives whatever licenses to the work the
party's predecessor in interest had or could give under the previous paragraph, plus a right
to possession of the Corresponding Source of the work from the predecessor in interest, if
the predecessor has it or can get it with reasonable efforts.
You may not impose any further restrictions on the exercise of the rights granted or
affirmed under th is L icense. For example, you may not impose a license fee, royalty, or
other charge for exercise of rights granted under this License, and you may not initiate
litigat ion (including a cross-claim or counterclaim in a lawsuit) a lle ging that any patent
claim is infringed by making, using, selling, offering for sale, or importing the Program or
any portion of it.
11. Patents.
A “contributor” is a copyright holde r who authori zes use un der this License o f the Progr am
or a work on which the Program is based. The work thus licensed is called the contributor's
“contributor version”.
A contributor's “essential patent claims” are all patent claims owned or controlled by the
contributor, whether already acquired or hereafter acquired, that would be infringed by
some manner, permitted by this License, of making, using, or selling its contributor version,
but do not include claims that would be infringed only as a consequence of further
modification of the contributor version. For purposes of this definition, “control” includes
the right to g rant patent s ublicenses in a m a nn er consistent wi th the requir e ments of this
132
License.
Each contributor grants you a non-exclusive, worldwide, royalty-free patent license under
the contributor's essential patent claims, to make, use, sell, offer for sale, import and
otherwise run, modify and propagate the contents of its contributor version.
In the following three paragraphs, a “patent license” is any express agreement or
commitment, however denominated, not to enforce a patent (such as an express
permission to practi ce a patent or covenant not to sue for patent infringe ment). To “gr ant”
such a patent license to a party means to make such an agreement or commitment not to
enforce a patent against the party.
If you convey a covered work, knowingly relying on a patent license, and the Corresponding
Source of the work is not a vail able for anyone to copy, free of charge and under the terms
of this License, through a publicly available network server or other readily accessible
means, then you m ust either (1) cause the Corresponding Source to be so available, or (2)
arrange to deprive yourself of the benefit of the patent license for this particular work, or (3)
arrange, in a manner consistent with the requirements of this License, to extend the patent
license to downstream recipients. “Knowingly relying” means you have actual knowledge
that, but for the patent license, your conveying the covered work in a country, or your
recipient's use of the covered work in a country, would infringe one or more identifiable
patents in that country that you have reaso n to believe are valid.
If, pursuant to or in connection with a single transaction or arrangement, you convey, or
propagate by procuring conveyance of, a covered work, and grant a patent license to some
of the parties receiving the covered work authorizing them to use, propagate, modify or
convey a specific copy of the covered work, then the patent license you grant is
automatically extended to all recipients of the covered work and works based on it.
A paten t license is “discriminatory” if it does not includ e within the scope of its coverage,
prohibits the exercise of , or i s conditioned on the non-exercise of one or more of the rights
that are specifi cally granted unde r this License. You ma y not conv ey a cov ered work if you
are a party to an arrangement with a third party that is in the business of distribut in g
software, under which you make payment to the third party based on the extent of your
activity of conveying the work, and under which the third party grants, to any of the parties
who would receive the covered work from you, a discriminatory p atent license (a) in
connection with copies of the covered work conveyed by you (or copies made from those
copies), or (b) primarily for and in connection with specific products or compilations that
133
contain the covered work, unless you entered into that arr angement, or that patent license
was granted, prior to 28 March 2007.
Nothing in this License shall be construed as excluding or limiting any implied license or
other defenses to in fringement that may otherwise be available to you under applicable
patent law.
12. No Surrender of Others' Freedom.
If conditions are imposed on you (whether by court order, agreement or otherwise) that
contradict the conditions of this License, they do not ex cuse you from the conditions of this
License. If you cannot convey a covered work so as to satisfy simultaneously your
obliga tio ns under this License and any othe r pertinent o bligations, then as a co nsequence
you ma y not convey it at all. For example, if you agree to terms that obligate you to collect
a royal ty for further conveying from those to whom you conve y the Program, the only wa y
you could satisfy both those terms and this License would be to refrain entirely from
conveying the Program.
13. Use with the GNU Affero General Public License.
Notwithstanding any other provision of this License, you have permission to link or combine
any covered work with a work licensed under version 3 of the GNU Affero General Public
License into a single combined work, and to convey the resulting work. The terms of this
License will continue to apply to the part which is the covered work, but the special
require me nts of the G NU Affe ro Ge ne ral Publi c Li ce nse, sec ti on 1 3, con ce rni ng i nte raction
through a network will apply to the combinat ion as such.
14. Revised Versions of this License.
The Free Software Foundation may publish revised and/or new versions of the GNU General
Public License from time to time. Su ch new versions will be similar in spirit to the present
version, but may differ in detail to address new problems or concerns.
Each version is given a distinguishing version number. If the Program specifies that a
certain numbered version of the GNU Gener al Public License “or an y later v ersion” applies
to it, you have the option of following the terms and conditions either of that numbered
version or of any later version published by the Free Software Foundation. If the Program
does not specify a version number of the GNU General Public License, you may choose any
version ever published by the Free Software Foundation.
If the Program specifies that a pro xy can decide which future versions of the GNU Gener al
134
Public License can be used, that proxy's public statement of acceptance of a version
permanently authorizes you to choose that version for the Program.
Later lice nse versions may give you addit ional or dif ferent per m issions. However, no
additional obligations are imposed on any author or copyright holder as a result of your
choosing to follow a later version.
15. Disclaimer of Warranty.
THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE
LAW. EXCEPT WHEN O THERWISE ST A TED IN WRITING THE COPYRIGHT HOLDERS AND/OR
OTHER PART IES PROVIDE THE PROGRAM “AS IS” WITHOUT WARRANTY OF ANY KIND,
EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE
ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU.
SHOULD TH E PR O G R AM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY
SERVICING, REPAIR OR CORRECTION.
16. Limit ation of Liability.
IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL
ANY COPYRIG HT H OL DER, O R A NY OTHER PARTY WHO MODIFIES A ND /O R CON VE YS TH E
PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY
GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE
USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF
DA T A OR DA T A BEING RENDERED INACCURA TE OR LOSSES SUST AINED BY YOU OR THIRD
PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS),
EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES.
17. Interpretation of Sections 15 and 16.
If the disclaimer of warr anty and limitation of liability provided above cannot be given local
legal effect according to their terms, reviewing courts shall apply local law that most closely
approximates an absolute waiver of all civil liability in connection with the Program, unless
a warranty or assumption of liability accompanies a copy of the Program in return for a fee.
END OF TERMS AND CONDITIONS
135
Appendix A: Product Complian ce Cl ass
FCC CE NAS Models
Class A Class A
TS-EC1679U-RP, TS-EC1279U-RP, TS-EC879U-RP,
TS-1679U-RP, TS-1279U-RP, TS-1270U-RP, TS-1263U-RP,
TS-1263U, TS-1253U-RP, TS-1253U, TS-879U-RP,
TS-870U-RP, TS-863U-RP, TS-853U-RP, TS-853U,
TS-453U-RP, TS-453U, TS-1079 Pro, TS-879 Pro, TS-
863U,
TS-463U, TS-463U-RP, TS-451U, TS-431U, TVS-871U-
RP,
TVS-1271U-RP, TS-431XU, TS-431XU-RP, TS-831XU,
TS-831XU-RP, TS-1231XU, TS-1231XU-RP
Class B Class B
TS-853S Pro, TS-453S Pro, TS-870 Pro, TS-853 Pro,
TS-670 Pro, TS-653 Pro, TS-470 Pro, TS-453 P ro, TS-253
Pro, TS-431+, TS-231+, TS-451S, TS-870, TS-851,
TS-670, TS-651, TS-470, TVS-863+, TVS-863, TVS-663,
TVS-463, TVS-471, TVS-671, TVS-871, TS-451, TS-
451+,
TS-431, TS-251, TS-251+, TS-251C, TS-231, T S-131,
TS-269H, TS-212P, TS-112P, HS-251, HS-251+, HS-210,
TS-453Bmini, TS-453mini, TS-563, IS-453S, TS-531P,
TS-531X, TS-253A, TS-453A, TS-653A, TS-853A, TS-
128,
TS-228, TAS-168, TS-268, TBS-453A, TS-831X, TS-
251A,
TS-451A, TS-1635, TVS-473, TVS-673, TVS-873, TS-
131P,
TS-231P, TS-431P