Table of Contents
QNAP TVS-672XT User Manual
Displayed below is the user manual for TVS-672XT by QNAP which is a product in the NAS & Storage Servers category. This manual has pages.
Related Manuals
TVS-x72XT
TVS-472XT
TVS-672XT
TVS-872XT
User Guide
Document Version: 4
16/03/2022
Contents
1. Preface
About This Guide........................................................................................................................................................3
Audience..................................................................................................................................................................... 3
Document Conventions.............................................................................................................................................3
2. Product Overview
About the TVS-x72XT................................................................................................................................................. 4
Hardware Specications............................................................................................................................................4
Package Contents...................................................................................................................................................... 7
Components............................................................................................................................................................... 8
Front Panel.............................................................................................................................................................8
Rear Panel.............................................................................................................................................................. 9
System Board.......................................................................................................................................................11
Drive Numbering.................................................................................................................................................12
Safety Information...................................................................................................................................................13
Installation Requirements...................................................................................................................................... 14
Setting Up the NAS.................................................................................................................................................. 15
3. Installation and Conguration
Hardware Installation..............................................................................................................................................16
Drive Installation.................................................................................................................................................16
Expansion Card Installation...............................................................................................................................26
Replacing Memory Modules.............................................................................................................................. 34
QTS Installation........................................................................................................................................................37
Installing QTS Using Qnder Pro...................................................................................................................... 38
Installing QTS Using the Cloud Key...................................................................................................................40
Installing QTS Using an HDMI Connection...................................................................................................... 43
4. Basic Operations
Power Button........................................................................................................................................................... 45
Reset Button.............................................................................................................................................................45
USB One Touch Copy Button.................................................................................................................................. 45
LCD Panel..................................................................................................................................................................46
Viewing TCP/IP Settings..................................................................................................................................... 46
Conguring TCP/IP Settings.............................................................................................................................. 46
Viewing Drive Information.................................................................................................................................47
Viewing Volume Information.............................................................................................................................47
Viewing System Information............................................................................................................................. 48
Powering O the NAS.........................................................................................................................................48
Restarting the NAS..............................................................................................................................................48
Changing the LCD Password..............................................................................................................................48
LCD Error Messages............................................................................................................................................49
LEDs...........................................................................................................................................................................49
Audio Alert................................................................................................................................................................51
5. NAS Migration
NAS Migration Requirements.................................................................................................................................52
Status and Setting Changes after NAS Migration................................................................................................52
Migrating a NAS....................................................................................................................................................... 53
Migrating NAS Data Using HBS 3...........................................................................................................................54
TVS-x72XT User Guide
1
Preparing the Destination NAS......................................................................................................................... 54
Creating a One-Way Sync Job.............................................................................................................................55
Importing Local Users or Group Settings to the Destination NAS................................................................56
6. Troubleshooting
Forcing Qnder Pro or myQNAPcloud to Locate the NAS.................................................................................. 58
Hot-swapping Failed Drives....................................................................................................................................58
Support and Other Resources................................................................................................................................58
7. Glossary
CloudKey................................................................................................................................................................... 60
CloudLink.................................................................................................................................................................. 60
myQNAPcloud.......................................................................................................................................................... 60
myQNAPcloud ID..................................................................................................................................................... 60
Qnder Pro............................................................................................................................................................... 60
QTS.............................................................................................................................................................................60
8. Notices
Limited Warranty..................................................................................................................................................... 61
Disclaimer................................................................................................................................................................. 61
GNU Public License..................................................................................................................................................61
CE Notice...................................................................................................................................................................69
UKCA Notice..............................................................................................................................................................69
FCC Notice.................................................................................................................................................................69
VCCI Notice............................................................................................................................................................... 70
BSMI Notice.............................................................................................................................................................. 70
SJ/T 11364-2006........................................................................................................................................................70
2
1. Preface
About This Guide
This guide provides information on the QNAP TVS-x72XT NAS and step-by-step instructions on installing the
hardware. It also provides instructions on basic operations and troubleshooting information.
Audience
This document is intended for consumers and storage administrators. This guide assumes that the user has
a basic understanding of storage and backup concepts.
Document Conventions
Symbol Description
Notes provide default conguration settings and other supplementary
information.
Important notes provide information on required conguration settings and
other critical information.
Tips provide recommendations or alternative methods of performing tasks or
conguring settings.
Warnings provide information that, when ignored, may result in potential loss,
injury, or even death.
TVS-x72XT User Guide
Preface 3
2. Product Overview
This chapter provides basic information about the QNAP TVS-x72XT NAS.
About the TVS-x72XT
The TVS-x72XT is a high-performance NAS powered by an Intel® processor and supports up to 16 GB of
DDR4 memory. It features an HDMI port for external displays and a USB One Touch Copy port for quick and
convenient backup and data transfer. In addition to its three network ports (two 1GbE and one 10GbE), the
TVS-x72XT is equipped with two Thunderbolt™ 3 ports (through its PCIe 3.0 x16 slot) that provide a wide
range of possibilities, including extra data management capabilities and additional multimedia support.
Hardware Specications
Warning
If your QNAP product has hardware defects, return the product to QNAP or a QNAP-
authorized service center for maintenance or replacement. Any attempt to repair or
perform maintenance procedures on the product by you or an unauthorized third party
invalidates the warranty.
QNAP is not responsible for any damage or data loss caused by unauthorized
modications and installation of unsupported third-party applications.
For details, see the QNAP Warranty Terms and Conditions.
Ordering P/N CPU Pre-installed memory
TVS-472XT-PT-4G Intel® Pentium® Series 4 GB RAM: 2 x 2 GB
SODIMM DDR4
TVS-472XT-i3-4G Intel® Core™ i3 Series 4 GB RAM: 2 x 2 GB
SODIMM DDR4
TVS-472XT-i5-4G Intel® Core™ i5 Series 4 GB RAM: 2 x 2 GB
SODIMM DDR4
TVS-672XT-i3-8G Intel® Core™ i3 Series 8 GB RAM: 2 x 4 GB
SODIMM DDR4
TVS-672XT-i5-8G Intel® Core™ i5 Series 8 GB RAM: 2 x 4 GB
SODIMM DDR4
TVS-872XT-i3-8G Intel® Core™ i3 Series 8 GB RAM: 2 x 8 GB
SODIMM DDR4
TVS-872XT-i5-16G Intel® Core™ i5 Series 16 GB RAM: 2 x 4 GB
SODIMM DDR4
TVS-872XT-i7-16G Intel® Core™ i7 Series 16 GB RAM: 2 x 8 GB
SODIMM DDR4
Component TVS-472XT TVS-672XT TVS-872XT
Ordering Information
Ordering P/N • TVS-472XT-PT-4G
• TVS-472XT-i3-4G
• TVS-472XT-i5-4G
• TVS-672XT-i3-8G
• TVS-672XT-i5-8G
• TVS-872XT-i3-8G
• TVS-872XT-i5-16G
• TVS-872XT-i7-16G
Processor
Architecture x86 64-bit
TVS-x72XT User Guide
Product Overview 4
Component TVS-472XT TVS-672XT TVS-872XT
Encryption engine AES-NI
Graphics Embedded Intel® UHD
610 graphics processor
Embedded Intel® UHD 630 graphics processor
Memory
Memory slots 2 x SODIMM DDR4
Important
• Use only QNAP memory modules to maintain system
performance and stability. For NAS devices with more
than one memory slot, use QNAP modules with identical
specications.
• Using unsupported modules may degrade performance,
cause errors, or prevent the operating system from
starting.
Maximum memory 64 GB RAM: 2 x 32 GB
Flash memory 4 GB USB DOM
Storage
Drive bays 4 x 3.5-inch SATA 6 Gbps 6 x 3.5-inch SATA 6 Gbps 8 x 3.5-inch SATA 6 Gbps
Drive compatibility • 3.5-inch SATA hard disk drives
• 2.5-inch SATA hard disk drives
• 2.5-inch SATA solid-state drives
M.2 SSD slots 2 x PCIe 3.0 x2
M.2 SSD form factor 2280
SSD cache acceleration
support
• 3.5-inch drive bays: 1
to 4
• 3.5-inch drive bays: 1
to 6
• 3.5-inch drive bays: 1
to 8
• M.2 SSD slots: 1 to 2
• M.2 SSD slots on an M.2 SSD expansion card
Hot-swapping The device supports hot-swapping drives except for the following:
• M.2 SSDs
• SSD cache drives
• M.2 SSD slots on an M.2 SSD expansion card
Network
10 Gigabit network
interface
1 x 10 GbE RJ45
Gigabit network interface 2 x GbE RJ45
External I/O Ports & Expansion Slots
TVS-x72XT User Guide
Product Overview 5
Component TVS-472XT TVS-672XT TVS-872XT
PCIe slots • 1 x PCIe 3.0 x16
• 1 x PCIe 3.0 x4
Note
A Thunderbolt™ 3 expansion card is preinstalled in the PCIe
3.0 x16 slot.
For the list of compatible drive models and expansion cards,
go to https://www.qnap.com/compatibility.
Thunderbolt™ ports 2 x Thunderbolt™ 3 (preinstalled expansion card)
USB ports Front:
• 1 x USB 3.1 Gen 2 (10Gbps) Type-A
Note
This USB port supports One Touch Copy.
Rear:
• 1 x USB 3.1 Gen 2 (10Gbps) Type-A
• 1 x USB 3.0 Type-A
• 2 x USB 3.1 Gen 2 (10Gbps) Type-C
HDMI ports 1 x HDMI 2.0 (up to 3840 x 2160 resolution at 60 Hz)
Interface
Display panel Monochrome backlit LCD display
Buttons • Power
• Reset
• USB One Touch Copy
IR sensor 1
Note
The TVS-x72XT supports the QNAP RM-IR004 IR remote
control.
Dimensions
Form factor Tower
Dimensions (H x W x D) 188.2 x 199.3 x 279.6 mm
(7.41 x 7.85 x 11.01 in)
188.2 x 264.3 x 279.6 mm
(7.41 x 10.40 x 11.01 in)
188.2 x 329.3 x 279.6 mm
(7.41 x 12.96 x 11.01 in)
Net weight 5.4 kg (11.9 lbs) 6.5 kg (14.3 lbs) 7.0 kg (15.5 lbs)
Others
Power supply unit 1 x 250W, 100-240V AC, 50/60 Hz
System battery CR2032 lithium battery (3V, 225 mAh)
Warning
To avoid potential battery explosion, causing injury or
damage to components, ensure that you replace the existing
battery with a battery of the same type.
TVS-x72XT User Guide
Product Overview 6
Component TVS-472XT TVS-672XT TVS-872XT
Sound level 28.1 dB(A) 23.8 dB(A) 24.2 dB(A)
Note
The sound level was tested at a bystander position, which is
within one meter of the NAS. The test NAS operated at low
speed with the maximum number of drives installed.
Fans • System: 1 x 12 cm,
12V DC smart fan
• CPU: 2 x 6 cm blower
fans
• System: 2 x 9.2 cm,
12V DC smart fans
• CPU: 2 x 6 cm blower
fans
• System: 2 x 12 cm,
12V DC smart fans
• CPU: 2 x 6 cm blower
fans
Warning
To avoid potential injury or damage to components, do not
touch the fans while the NAS is connected to a power source.
Operating temperature 0˚C to 40˚C (32˚F to 104˚F)
Relative humidity • Non-condensing relative humidity: 5% to 95%
• Wet-bulb temperature: 27˚C (80.6˚F)
Security slot Kensington security slot
Tip
Model specications are subject to change without prior notice. To see the latest
specications, go to https://www.qnap.com.
Package Contents
Item Quantity
TVS-x72XT NAS 1
Power cord 1
Ethernet cables 3:
• 2 x 1 GbE (Cat5e)
• 1 x 10 GbE (Cat6a)
Screws for 3.5-inch drives • TVS-472XT: 12
• TVS-672XT: 18
• TVS-872XT: 24
Screws for 2.5-inch drives • TVS-472XT: 12
• TVS-672XT: 18
• TVS-872XT: 24
Heatsinks for M.2 SSDs 2
Quick Installation Guide (QIG) 1
TVS-x72XT User Guide
Product Overview 7
Components
Front Panel
TVS-472XT
TVS-672XT
TVS-x72XT User Guide
Product Overview 8
TVS-872XT
No. Component No. Component
1 LCD panel 7 USB One Touch Copy button
2 LCD enter button 8 IR sensor
3 LCD select button 9 M.2 SSD LEDs
4 Drive LEDs 10 USB LED
5 Power button 11 LAN LED
6 USB 3.1 Gen 2 One Touch Copy Type-A port 12 Status LED
Rear Panel
TVS-472XT
TVS-x72XT User Guide
Product Overview 9
No. Component No. Component
1 Power input 7 10 Gigabit Ethernet port (RJ45)
2 System fan 8 Kensington security slot
3 Gigabit Ethernet ports (RJ45) 9 HDMI 2.0 port
4 USB 3.1 Gen 2 Type-A port 10 PCIe low-prole cover
5 USB 3.1 Gen 2 Type-C ports 11 Reset button
6 USB 3.0 Type-A port 12 Thunderbolt™ 3 ports
TVS-672XT
No. Component No. Component
1 Power input 8 USB 3.0 Type-A port
2 System fan 9 10 Gigabit Ethernet port (RJ45)
3 System fan 10 HDMI 2.0 port
4 Kensington security slot 11 PCIe full-height cover
5 Gigabit Ethernet ports (RJ45) 12 Reset button
6 USB 3.1 Gen 2 Type-A port 13 Thunderbolt™ 3 ports
7 USB 3.1 Gen 2 Type-C ports - -
TVS-x72XT User Guide
Product Overview 10
TVS-872XT
No. Component No. Component
1 Kensington security slot 8 USB 3.0 Type-A port
2 Power input 9 10 Gigabit Ethernet port (RJ45)
3 System fan 10 HDMI 2.0 port
4 System fan 11 PCIe full-height cover
5 Gigabit Ethernet ports (RJ45) 12 Reset button
6 USB 3.1 Gen 2 Type-A port 13 Thunderbolt™ 3 ports
7 USB 3.1 Gen 2 Type-C ports - -
System Board
TVS-x72XT User Guide
Product Overview 11
Note
This image does not show the chassis.
No. Component No. Component
1 PCIe slot 1 (PCIe 3.0 x16)
Note
A Thunderbolt™ 3 expansion card
is preinstalled in this slot.
4 M.2 SSD slot 2
2 PCIe slot 1 (PCIe 3.0 x4) 5 Memory slot 1
3 M.2 SSD slot 1 6 Memory slot 2
Drive Numbering
TVS-472XT
TVS-x72XT User Guide
Product Overview 12
TVS-672XT
TVS-872XT
Safety Information
The following instructions help ensure personal safety and environmental safety. Read these instructions
carefully before performing any operation.
General Instructions
• The device should be stored in a secure location with restricted access, controlled through the use of a
tool, lock and key, or any means of security.
• Only qualied, skilled, and authorized persons with knowledge of all restrictions, safety precautions,
and installation and maintenance procedures should have physical access to the device.
TVS-x72XT User Guide
Product Overview 13
• To avoid potential injury or damage to components, ensure that the drives and other internal system
components have cooled before touching them.
• Observe electrostatic discharge (ESD) procedures to avoid potential injury or damage to components.
Power
• To reduce the risk of re or electric shock, ensure that you only connect the power cord to a properly
grounded electrical outlet.
• To avoid serious injuries, a trained service technician must disconnect all PSU cords from the device
before installing or replacing system components.
System Battery
• To avoid potential battery explosion, causing injury or damage to components, ensure that you replace
the existing battery with a battery of the same type.
• Dispose of used batteries properly according to local regulations or the instructions of the battery
manufacturer.
Moving Parts
•
Moving fan blades: Keep your body parts away from moving fan blades while the device is connected
to a power source.
•
Moving components: Keep your body parts away from other moving components.
• The device is not suitable for use in locations where children are likely to be present.
Installation Requirements
Category Item
Environment • Room temperature: 0˚C to 40˚C (32˚F to 104˚F)
• Non-condensing relative humidity: 5% to 95%
• Wet-bulb temperature: 27˚C (80.6˚F)
• Flat, anti-static surface without exposure to direct sunlight, liquids,
or chemicals
Hardware and peripherals • Storage drives
For details on compatible drives, go to https://www.qnap.com/
compatibility/.
• Network cable
Tools • Phillips #1 or #2 screwdriver
• Anti-static wrist strap
TVS-x72XT User Guide
Product Overview 14
Setting Up the NAS
Important
Read all safety requirements and information carefully before setting up the NAS or
installing NAS components.
1. Place your NAS device in an environment that meets the requirements.
For details, see Installation Requirements.
2. Install the drives.
For details, see the following topics:
•Installing 3.5-inch Drives on 3.5-inch Trays
•Installing 2.5-inch Drives on 3.5-inch Trays
•Installing M.2 Solid-state Drives
3. Connect the power cord and all applicable cables.
4. Power on the NAS.
5. Install QTS.
For details, see QTS Installation.
6. Log on to QTS.
TVS-x72XT User Guide
Product Overview 15
3. Installation and Conguration
This chapter provides specic hardware and rmware installation and conguration steps.
Hardware Installation
This section provides information on installing drives and expansion cards and replacing memory modules.
Drive Installation
The TVS-x72XT is compatible with 3.5-inch and 2.5-inch hard drives, 2.5-inch solid-state drives, and M.2
solid-state drives.
Installing 3.5-inch Drives on 3.5-inch Trays
Warning
• Installing a drive deletes all data on the drive.
• Observe electrostatic discharge (ESD) procedures to avoid damage to components.
1. Power o the NAS.
2. Remove the drive tray.
a. Slide the lock down.
b. Pull the handle to release the tray.
c. Pull the tray out.
3. Install a drive on the tray.
a. Remove the fastening panels from the sides of the tray.
TVS-x72XT User Guide
Installation and Conguration 16
b. Place the drive on the tray so that the holes on the sides of the drive are aligned with the holes on
the sides of the tray.
c. Attach the fastening panels.
d. Optional: Attach the screws to further secure the drive.
TVS-x72XT User Guide
Installation and Conguration 17
Important
QNAP recommends attaching the screws to the drive trays when transporting the NAS.
4. Load the tray into the drive bay.
a. Insert the tray into the bay.
b. Push the handle.
c. Slide the lock up.
5. Power on the NAS.
TVS-x72XT User Guide
Installation and Conguration 18
Installing 2.5-inch Drives on 3.5-inch Trays
Warning
• Installing a drive deletes all data on the drive.
• Observe electrostatic discharge (ESD) procedures to avoid damage to components.
1. Power o the NAS.
2. Remove the drive tray.
a. Slide the lock down.
b. Pull the handle to release the tray.
c. Pull the tray out.
3. Install a drive on the tray.
a. Remove the right fastening panel from the tray.
TVS-x72XT User Guide
Installation and Conguration 19
b. Place the drive on the tray so that the holes on the bottom of the drive are aligned with the holes
on the bottom of the tray.
c. Attach the screws.
4. Load the tray into the drive bay.
a. Insert the tray into the bay.
b. Push the handle.
TVS-x72XT User Guide
Installation and Conguration 20
c. Slide the lock up.
5. Power on the NAS.
Installing M.2 Solid-state Drives
Warning
• Only qualied personnel should perform the following steps. Failure to follow
instructions can result in serious injury or death.
• Observe electrostatic discharge (ESD) procedures to avoid damage to components.
•
Moving fan blades: Keep your hands and other body parts away from moving fan
blades.
•
Other moving components: Keep your hands and other body parts away from other
moving components.
Note
• The TVS-x72XT has two M.2 SSD slots. For a list of compatible M.2 SSDs, go to https://
www.qnap.com/compatibility.
• QNAP recommends installing heatsinks on M.2 SSD controllers to enhance cooling
eciency and ensure consistent performance.
TVS-x72XT User Guide
Installation and Conguration 21
• Before installing non-QNAP heatsinks, ensure that they are of the appropriate size and
shape.
1. Power o the NAS.
2. Disconnect the power cord from the electrical outlet.
3. Disconnect all cables and external attachments.
4. Remove the case cover.
a. Remove the screws that secure the case cover to the chassis.
b. Slide the cover back.
c. Lift the cover until it is completely detached from the chassis.
5. Position the NAS on its right side.
6. Install a heatsink on the M.2 SSD controller.
a. Locate the controller on the M.2 SSD.
Note
The location of the controller varies depending on the model and manufacturer of the M.2 SSD.
For details, refer to the documentation or contact the manufacturer.
b. Remove the protective lm from the bottom of the heatsink.
TVS-x72XT User Guide
Installation and Conguration 22
c. Install the heatsink on the controller.
7. Install the M.2 SSD.
a. Pull out the pushpin.
TVS-x72XT User Guide
Installation and Conguration 23
b. Insert the M.2 SSD.
c. Insert the pushpin to secure the drive.
TVS-x72XT User Guide
Installation and Conguration 24
8. Place the NAS in its normal upright position.
9. Attach the case cover.
a. Slide the cover down until it is completely connected to the chassis.
b. Slide the cover forward.
c. Attach the screws to the back of the NAS.
10. Connect all cables and external attachments.
11. Connect the power cord to the electrical outlet.
12. Power on the NAS.
TVS-x72XT User Guide
Installation and Conguration 25
Expansion Card Installation
The TVS-x72XT supports selected expansion cards, some of which require QNAP PCIe brackets. QNAP-
branded expansion cards purchased from the company website are shipped with the brackets necessary to
t all QNAP NAS models.
For details on supported expansion cards and brackets, go to http://www.qnap.com/compatibility.
Installing Expansion Cards on the TVS-472XT
Note
This process applies only to the TVS-472XT. For details on the TVS-672XT or TVS-872XT, see
Installing Expansion Cards on the TVS-672XT and TVS-872XT.
Warning
• Only qualied personnel should perform the following steps. Failure to follow
instructions can result in serious injury or death.
• Observe electrostatic discharge (ESD) procedures to avoid damage to components.
•
Moving fan blades: Keep your hands and other body parts away from moving fan
blades.
•
Other moving components: Keep your hands and other body parts away from other
moving components.
1. Check the expansion cards and brackets supported by your model on the QNAP website.
a. Go to www.qnap.com/compatibility.
b. Click Search by NAS.
c. Specify the number of bays and the specic model of your NAS.
d. Under Category, select the component or device type.
e. Locate a specic component or device model on the list.
f. Optional: Click the corresponding Note icon to view more information.
2. Power o the NAS.
3. Disconnect the power cord from the electrical outlet.
4. Disconnect all cables and external attachments.
5. Remove the case cover.
a. Remove the screws that secure the case cover to the chassis.
TVS-x72XT User Guide
Installation and Conguration 26
b. Slide the cover back.
c. Lift the cover until it is completely detached from the chassis.
6. Remove the power supply unit.
Warning
To avoid potential injury or damage to components, ensure that the drives and other internal
system components have cooled before touching them.
a. Disconnect the power supply cables.
b. Remove the screws that secure the unit to the chassis.
c. Remove the unit from the chassis.
TVS-x72XT User Guide
Installation and Conguration 27
7. Remove the PCIe slot cover.
a. Remove the screw that secures the cover to the chassis.
b. Pull the cover away from the slot.
8. Install the expansion card.
a. Hold the edges of the expansion card and carefully insert it into the slot.
b. Attach the screw.
TVS-x72XT User Guide
Installation and Conguration 28
9. Install the power supply unit.
a. Install the unit on the chassis.
b. Attach the screws that secure the unit to the chassis.
TVS-x72XT User Guide
Installation and Conguration 29
c. Connect the power supply cables.
10. Attach the case cover.
a. Slide the cover down until it is completely connected to the chassis.
b. Slide the cover forward.
c. Attach the screws to the back of the NAS.
11. Connect all cables and external attachments.
12. Connect the power cord to the electrical outlet.
13. Power on the NAS.
TVS-x72XT User Guide
Installation and Conguration 30
Installing Expansion Cards on the TVS-672XT and TVS-872XT
Note
This process applies only to the TVS-672XT and TVS-872XT. For details on the TVS-472XT,
see Installing Expansion Cards on the TVS-472XT.
Warning
• Only qualied personnel should perform the following steps. Failure to follow
instructions can result in serious injury or death.
• Observe electrostatic discharge (ESD) procedures to avoid damage to components.
•
Moving fan blades: Keep your hands and other body parts away from moving fan
blades.
•
Other moving components: Keep your hands and other body parts away from other
moving components.
1. Check the expansion cards and brackets supported by your model on the QNAP website.
a. Go to www.qnap.com/compatibility.
b. Click Search by NAS.
c. Specify the number of bays and the specic model of your NAS.
d. Under Category, select the component or device type.
e. Locate a specic component or device model on the list.
f. Optional: Click the corresponding Note icon to view more information.
2. Power o the NAS.
3. Disconnect the power cord from the electrical outlet.
4. Disconnect all cables and external attachments.
5. Remove the case cover.
a. Remove the screws that secure the case cover to the chassis.
b. Slide the cover back.
c. Lift the cover until it is completely detached from the chassis.
TVS-x72XT User Guide
Installation and Conguration 31
6. Remove the PCIe slot cover.
a. Remove the screw that secures the cover to the chassis.
b. Pull the cover away from the slot.
7. Install the expansion card.
a. Hold the edges of the expansion card and carefully insert it into the slot.
b. Attach the screw.
TVS-x72XT User Guide
Installation and Conguration 32
8. Attach the case cover.
a. Slide the cover down until it is completely connected to the chassis.
b. Slide the cover forward.
c. Attach the screws to the back of the NAS.
9. Connect all cables and external attachments.
10. Connect the power cord to the electrical outlet.
11. Power on the NAS.
TVS-x72XT User Guide
Installation and Conguration 33
Replacing Memory Modules
The TVS-x72XT has two memory slots. You can increase the memory capacity of the NAS by upgrading
the memory modules. When using two modules, use only QNAP modules of the same type and capacity
to maintain system performance and stability. You can purchase QNAP memory modules from authorized
resellers.
Warning
• Only qualied personnel should perform the following steps. Failure to follow
instructions can result in serious injury or death.
• Observe electrostatic discharge (ESD) procedures to avoid damage to components.
•
Moving fan blades: Keep your hands and other body parts away from moving fan
blades.
•
Other moving components: Keep your hands and other body parts away from other
moving components.
1. Power o the NAS.
2. Disconnect the power cord from the electrical outlet.
3. Disconnect all cables and external attachments.
4. Remove each drive tray from the NAS.
a. Slide the lock down.
b. Pull the tray handle outward.
c. Pull the tray out.
TVS-x72XT User Guide
Installation and Conguration 34
5. Position the NAS on its right side.
6. Remove an existing module.
a. Push the retention clips outward simultaneously to release the module.
b. Verify that the module has tilted upward and is completely released from the slot.
Attempting to remove a module that is not completely released may damage the module and the
motherboard.
c. Hold the edges of the module and carefully pull it out of the slot.
Warning
Attempting to remove a module that is not completely released may damage the module and
the motherboard.
TVS-x72XT User Guide
Installation and Conguration 35
7. Install a new module.
a. Align the notch with the ridge in the slot.
b. Insert the module.
c. Verify that the metal connectors are fully inserted.
d. Carefully press down on the module until the retention clips lock the module into place.
8. Place the NAS in its normal upright position.
9. Load each drive tray back into the NAS.
a. Slide the tray into the drive bay.
TVS-x72XT User Guide
Installation and Conguration 36
b. Push the handle.
c. Slide the lock up.
10. Connect all cables and external attachments.
11. Connect the power cord to the electrical outlet.
12. Power on the NAS.
13. Verify that the module is recognized by the NAS.
a. Log on to QTS as administrator.
b. Go to Control Panel > System > System Status > Hardware Information .
c. Check the value for Total memory.
QTS Installation
The TVS-x72XT uses the QNAP QTS operating system. You can install QTS using any of the following
methods.
Method Description Requirements
Qnder Pro
installation
(Recommended)
If the NAS is connected to your local area
network, you can do the following:
• Locate the NAS using Qnder Pro.
• Complete the steps in the Smart
Installation Guide wizard.
For details, see Installing QTS Using
Qnder Pro.
• Computer
• Network cable
•Qnder Pro installer
TVS-x72XT User Guide
Installation and Conguration 37
Method Description Requirements
Cloud installation If the NAS is connected to the internet,
you can do the following:
• Scan the QR code on the NAS.
• Log into your myQNAPcloud account.
• Use myQNAPcloud Link to remotely
access your NAS.
• Complete the steps in the Smart
Installation Guide wizard.
For details, see Installing QTS Using the
Cloud Key.
• Computer or mobile device
• Network cable
• myQNAPcloud account
• Cloud Key
Local installation If the NAS supports HDMI output, you can
do the following:
• Connect the NAS to the required
hardware.
• Complete the steps in the Smart
Installation Guide wizard.
For details, see Installing QTS Using an
HDMI Connection.
• Monitor
• HDMI cable
• USB keyboard or Remote control (not
available on all models)
You can also install the QNAP QuTS hero operating system. If your NAS is connected to the internet, the
option to install QuTS hero will appear in the Smart Installation Guide wizard using any of the methods in
the table. You can also manually download the QuTS hero rmware from https://download.qnap.com.
Warning
QuTS hero and QTS use dierent le systems. Switching operating systems will reset the
NAS and delete all data.
Installing QTS Using Qnder Pro
Warning
Installing QTS deletes all data on the drives. Back up your data before proceeding.
Important
To protect your NAS from brute force attacks, create a new system administrator account
during QTS installation to disable the default "admin" account.
1. Power on the NAS.
2. Connect the NAS to your local area network.
3. Run Qnder Pro on a computer that is connected to the same local area network.
Note
To download Qnder Pro, go to https://www.qnap.com/utilities.
4. Click Next.
The QNAP Warranty Service page opens in the default web browser.
TVS-x72XT User Guide
Installation and Conguration 38
5. Click Check warranty.
The QNAP Warranty Service window opens in a new web page.
Important
You can check your device warranty policy or purchase an extended warranty plan at QNAP
Warranty Service.
6. Close the warranty page.
The Smart Installation Guide opens in the default web browser.
7. Click Next.
The Enter the NAS name and administrator’s password screen appears.
8. Specify the following information.
•NAS name: Specify a name with 1 to 14 characters. The name supports letters (A to Z, a to z),
numbers (0 to 9), and hyphens (-), but cannot end with a hyphen.
•Username: Specify an administrator username that contains 1 to 32 characters. The name
supports letters (A to Z, a to z), numbers (0 to 9), and hyphens (-), multi-byte Chinese, Japanese,
Korean, and Russian characters.
The username cannot contain the following special characters: grave accent (`), asterisk (*), equal
sign (=), plus sign (+), square brackets ([ ]), slash (\), vertical bar (|), semicolon (;), colon (:),
apostrophe ('), quotation mark ("), comma (,), less than sign (< ), greater than sign (>), backslash
(/), question mark (?), percent sign (%)
•Password: Specify an administrator password with 1 to 64 characters. The password supports all
ASCII characters.
•Conrm Password: Enter the new administrator password again.
9. Click Next.
The Set the date and time screen appears.
10. Specify the time zone, date, and time using any of the following methods:
Tip
QNAP recommends connecting to an NTP server to ensure that the NAS follows the
Coordinated Universal Time (UTC) standard.
Methods User Actions
Synchronize with computer or device time Select Same as the computer/device time
The NAS time will be the same as your computer or
device used to congure the time.
Enter manually a. Select Input Manually.
b. Specify the date and time.
The NAS date and time will be the same as the
congured time.
Synchronize with an Internet time server
automatically
Click Synchronize with an Internet time server
automatically.
The NAS time will be the same as the NTP server.
11. Click Next.
The Congure the network settings screen appears.
12. Congure the network settings using any of the following methods.
TVS-x72XT User Guide
Installation and Conguration 39
Methods User Actions
Obtain an IP address automatically (DHCP) Select Obtain an IP address automatically (DHCP)
The system automatically detects and congures the
IP address settings.
Use static IP address a. Select Use static IP address.
The IP address conguration page appears.
b. Specify the following IP address congurations:
• Interface
• IP Address
• Subnet Mask
• Default Gateway
• Primary DNS server
• Secondary DNS server
13. Click Next.
The Thunderbolt Connection page appears.
Note
This page only appears if your device supports Thunderbolt. You will need to connect your
device to a computer using a Thunderbolt cable.
14. Click Next.
The Summary screen appears.
15. Review the settings.
16. Click Apply.
A conrmation message appears.
Warning
Clicking Conrm deletes all data on the drive before installing QTS.
17. Click Conrm.
QTS is installed.
Installing QTS Using the Cloud Key
Warning
Installing QTS deletes all data on the drives. Back up your data before proceeding.
Important
To protect your NAS from brute force attacks, create a new system administrator account
during QTS installation to disable the default "admin" account.
1. Power on the NAS.
2. Connect the NAS to the internet.
3. Go to the QNAP Cloud Installation page using one of the following methods:
TVS-x72XT User Guide
Installation and Conguration 40
• On your computer, go to your respective region's site to download QTS:
• China: https://install.qnap.com.cn
• Global: https://install.qnap.com
• Scan the QR code on the NAS using a mobile device.
The web page lists all the uninitialized QNAP NAS devices on the local network.
4. Find your NAS from the list and then click Initialize.
Note
If your NAS is not listed, follow the instructions on the web page to specify the Cloud Key on the
NAS.
The installation wizard opens in the default web browser
5. Create an account or sign in to myQNAPcloud.
Note
You must return to this page to complete the installation after creating an account.
6. Specify the myQNAPcloud device name for the NAS.
Note
• The myQNAPcloud device name is used when remotely accessing the NAS.
• For security purposes, the myQNAPcloud Link remote connection service will be disabled
on your NAS after initialization. You can enable it by connecting to QTS through LAN and
then installing myQNAPcloud Link.
7. Click Next.
The QNAP Warranty Service page opens in the default web browser.
8. Click Check warranty.
The QNAP Warranty Service window opens in a new web page.
Important
You can check your device warranty policy or purchase an extended warranty plan at QNAP
Warranty Service.
9. Close the warranty page.
The Smart Installation Guide opens in the default web browser.
10. Specify the following information.
•NAS name: Specify a name with 1 to 14 characters. The name supports letters (A to Z, a to z),
numbers (0 to 9), and hyphens (-), but cannot end with a hyphen.
•Username: Specify an administrator username that contains 1 to 32 characters. The name
supports letters (A to Z, a to z), numbers (0 to 9), and hyphens (-), multi-byte Chinese, Japanese,
Korean, and Russian characters.
The username cannot contain the following special characters: grave accent (`), asterisk (*), equal
sign (=), plus sign (+), square brackets ([ ]), slash (\), vertical bar (|), semicolon (;), colon (:),
apostrophe ('), quotation mark ("), comma (,), less than sign (< ), greater than sign (>), backslash
(/), question mark (?), percent sign (%), or "admin".
TVS-x72XT User Guide
Installation and Conguration 41
•Password: Specify an administrator password with 1 to 64 characters. The password supports all
ASCII characters.
•Conrm Password: Enter the new administrator password again.
11. Click Next.
The Set the date and time screen appears.
12. Specify the time zone, date, and time using any of the following methods:
Tip
QNAP recommends connecting to an NTP server to ensure that the NAS follows the
Coordinated Universal Time (UTC) standard.
Methods User Actions
Synchronize with computer or device time Select Same as the computer/device time
The NAS time will be the same as your computer or
device used to congure the time.
Enter manually a. Select Input Manually.
b. Specify the date and time.
The NAS date and time will be the same as the
congured time.
Synchronize with an Internet time server
automatically
Click Synchronize with an Internet time server
automatically.
The NAS time will be the same as the NTP server.
13. Click Next.
The Congure the network settings screen appears.
14. Congure the network settings using any of the following methods.
Methods User Actions
Obtain an IP address automatically (DHCP) Select Obtain an IP address automatically (DHCP)
The system automatically detects and congures the
IP address settings.
Use static IP address a. Select Use static IP address.
The IP address conguration page appears.
b. Specify the following IP address congurations:
• Interface
• IP Address
• Subnet Mask
• Default Gateway
• Primary DNS server
• Secondary DNS server
15. Click Next.
The Thunderbolt Connection page appears.
TVS-x72XT User Guide
Installation and Conguration 42
Note
This page only appears if your device supports Thunderbolt. You will need to connect your
device to a computer using a Thunderbolt cable.
16. Click Next.
The Summary screen appears.
17. Review the settings.
18. Click Apply.
A conrmation message appears.
Warning
Clicking Conrm deletes all data on the drive before installing QTS.
19. Click Conrm.
QTS is installed.
Installing QTS Using an HDMI Connection
Warning
Installing QTS deletes all data on the drives. Back up your data before proceeding.
Important
To protect your NAS from brute force attacks, create a new system administrator account
during QTS installation to disable the default "admin" account.
1. Connect an HDMI display to the NAS.
2. Connect a USB keyboard to the NAS or prepare the QNAP IR remote control (not available on all
models).
3. Power on the NAS.
The Welcome screen of the Smart Installation Guide appears.
4. Select Start Smart Installation Guide.
The Enter the NAS name and administrator’s password screen appears.
5. Specify the following information:
•NAS name: Specify a name with 1 to 14 characters. The name supports letters (A to Z, a to z),
numbers (0 to 9), and hyphens (-), but cannot end with a hyphen.
•Username: Specify an administrator username that contains 1 to 32 characters. The name
supports letters (A to Z, a to z), numbers (0 to 9), and hyphens (-), multi-byte Chinese, Japanese,
Korean, and Russian characters.
The username cannot contain the following special characters: grave accent (`), asterisk (*), equal
sign (=), plus sign (+), square brackets ([ ]), slash (\), vertical bar (|), semicolon (;), colon (:),
apostrophe ('), quotation mark ("), comma (,), less than sign (< ), greater than sign (>), backslash
(/), question mark (?), percent sign (%)
•Password: Specify an administrator password with 1 to 64 characters. The password supports all
ASCII characters.
•Conrm Password: Enter the new administrator password again.
6. Click Next.
The Thunderbolt Connection page appears.
TVS-x72XT User Guide
Installation and Conguration 43
Note
This page only appears if your device supports Thunderbolt. You will need to connect your
device to a computer using a Thunderbolt cable.
7. Click Next.
The Summary screen appears.
8. Review the settings.
9. Click Next.
The Conrm screen appears.
Warning
Clicking Next deletes all data on the drive before installing QTS.
10. Click Next.
QTS is installed.
TVS-x72XT User Guide
Installation and Conguration 44
4. Basic Operations
This chapter describes basic NAS operations.
Power Button
Operation User Action Result
Power on Press the button once. The NAS powers on.
Power o Press and hold the button for 1.5
seconds.
The NAS powers o.
Force power o Press and hold the button for 5
seconds.
The NAS shuts down.
Important
Use this method only
when the NAS is
unresponsive.
Reset Button
Operation User Action Result
Basic system reset Press and hold the
button for 3 seconds.
The following settings are reset to default:
• System administrator password: admin
• TCP/IP conguration:
• Obtain IP address settings automatically via DHCP
• Disable jumbo frames
• If port trunking is enabled (multi-LAN models
only), the port trunking mode is reset to “Active
Backup (Failover)”.
• System port: 8080 (system service port)
• Security level: Low (Allow all connections)
• LCD panel password: (blank)
• VLAN: Disabled
Advanced system
reset
Press and hold the
button for 15 seconds.
The default factory settings are restored.
• To retrieve old data after an advanced system reset,
recreate the previous folder structure on the NAS.
USB One Touch Copy Button
The USB One Touch Copy button allows you to copy data backups from a USB device to the NAS or from the
NAS to a USB device.
This feature supports incremental backups. The NAS only copies les that were modied or added after the
last backup.
TVS-x72XT User Guide
Basic Operations 45
LCD Panel
The LCD panel allows you to perform the following operations:
• Restart and power o the NAS
•Congure or change the LCD panel password
• View and congure network settings
• View information on the system, physical disks, and volumes
Viewing TCP/IP Settings
You can view the following settings for each network adapter on the NAS:
• IP address
• Subnet mask
• Default gateway
• Primary DNS
• Secondary DNS
1. Press Enter or Select.
The panel displays the NAS name and QTS version.
2. Press and hold Enter for two seconds.
The panel displays Main Menu 1. TCP/IP.
3. Press and hold Enter.
The panel displays the IP address of the rst network adapter.
4. Press and hold Select to view the next TCP/IP screen.
5. Optional: Repeat step 4 as necessary.
Conguring TCP/IP Settings
You can congure the following settings for each network adapter on the NAS:
• IP address
• Subnet mask
• Default gateway
• Primary DNS
• Secondary DNS
1. Press Enter or Select.
The panel displays the NAS name and QTS version.
2. Press and hold Enter for two seconds.
The panel displays Main Menu 1. TCP/IP.
TVS-x72XT User Guide
Basic Operations 46
3. Press and hold Enter.
The panel displays the IP address of the rst network adapter.
4. Press Select repeatedly until the panel displays Enter Network Settings.
5. Press and hold Enter.
The panel displays the congurable network settings.
6. Press Select and Enter to congure the settings.
Button Usage
Enter • Display a conguration screen.
• Move to the next item on a conguration screen.
Select • Move to the next item on a menu.
• Modify a value on a conguration screen.
Viewing Drive Information
The LCD panel can display the temperature and capacity of each drive installed in the NAS.
1. Press Enter or Select.
The panel displays the NAS name and QTS version.
2. Press and hold Enter for two seconds.
The panel displays Main Menu 1. TCP/IP.
3. Press Enter repeatedly until the panel displays Main Menu 2. Physical disk.
4. Press and hold Enter.
The panel displays the temperature and capacity of the drive in slot 1.
5. Press and hold Select.
The panel displays the temperature and capacity of the next drive.
6. Optional: Repeat step 5 as necessary.
Viewing Volume Information
The LCD panel can display the name and capacity of each volume.
1. Press Enter or Select.
The panel displays the NAS name and QTS version.
2. Press and hold Enter for two seconds.
The panel displays Main Menu 1. TCP/IP.
3. Press Enter repeatedly until the panel displays Main Menu 3. Volume.
4. Press and hold Enter.
The panel displays the name and capacity of the rst volume.
5. Press and hold Select.
The panel displays the name and capacity of the next volume.
6. Optional: Repeat step 5 as necessary.
TVS-x72XT User Guide
Basic Operations 47
Viewing System Information
The LCD panel can display the CPU temperature, system temperature, and system fan speed.
1. Press Enter or Select.
The panel displays the NAS name and QTS version.
2. Press and hold Enter for two seconds.
The panel displays Main Menu 1. TCP/IP.
3. Press Enter repeatedly until the panel displays Main Menu 4. System.
4. Press and hold Enter.
The panel displays the CPU and system temperature.
5. Press and hold Select.
The panel displays the system fan speed.
Powering O the NAS
1. Press Enter or Select.
The panel displays the NAS name and QTS version.
2. Press and hold Enter for two seconds.
The panel displays Main Menu 1. TCP/IP.
3. Press Enter repeatedly until the panel displays Main Menu 5. Shut down.
4. Press and hold Enter.
The NAS powers o.
Restarting the NAS
1. Press Enter or Select.
The panel displays the NAS name and QTS version.
2. Press and hold Enter for two seconds.
The panel displays Main Menu 1. TCP/IP.
3. Press Enter repeatedly until the panel displays Main Menu 6. Reboot.
4. Press and hold Enter.
The NAS restarts.
Changing the LCD Password
Specifying a password for the LCD panel prevents unauthorized access.
1. Press Enter or Select.
The panel displays the NAS name and QTS version.
2. Press and hold Enter for two seconds.
The panel displays Main Menu 1. TCP/IP.
3. Press Enter repeatedly until the panel displays Main Menu 7. Password.
4. Press and hold Enter.
TVS-x72XT User Guide
Basic Operations 48
The Change Password screen appears.
5. Select Yes by pressing and holding Enter.
The New Password screen appears.
6. Press Select and Enter to specify a new password.
• Specify a password with 1 to 8 characters. The password can only contain numbers (0 to 9).
• To remove the password, leave the password eld blank.
Button Usage
Enter Move to the next item in the New Password screen.
Select Change a number in the New Password and Verify Password
screens.
7. Press Enter.
The NAS saves the password.
LCD Error Messages
System Message Description
Sys. Fan Failed The system fan failed.
Sys. Overheat The system overheated.
HDD Overheat The drive overheated.
CPU Overheat The CPU overheated.
Network Lost LAN 1, LAN 2, LAN3, and LAN 4 are disconnected in failover or are in
load-balancing mode.
LAN1 Lost LAN 1 is disconnected.
LAN2 Lost LAN 2 is disconnected.
LAN3 Lost LAN 3 is disconnected.
LAN4 Lost LAN 4 is disconnected.
HDD Failure The drive failed.
Vol1 Full The volume is full.
HDD Ejected The drive was ejected.
Vol1 Degraded The volume is in degraded mode.
Vol1 Unmounted The volume is unmounted.
Vol1 Nonactivate The volume is not activated.
LEDs
LEDs indicate system status and related information when the NAS is powered on. The following LED
information applies only when the drive is correctly installed and when the NAS is connected to the network.
For details on the location of the LEDs, see Components.
TVS-x72XT User Guide
Basic Operations 49
LED Status Description
System Status Flashes green and red
alternately every 0.5
seconds
• The drive is being formatted.
• The NAS is being initialized.
• The operating system is being updated.
• RAID rebuilding is in progress.
• Online RAID Capacity Expansion is in progress.
• Online RAID Level Migration is in progress.
Red • The drive is invalid.
• The disk volume has reached its full capacity.
• The disk volume is about to reach its full capacity.
• The system fan is not functioning.
• An error occured when accessing (read/write) the data.
• A bad sector is detected on the hard drive.
• The NAS is in degraded read-only mode (two member
drives failed in RAID 5 or RAID 6 but the data can still
be read).
• Hardware self-test error
Flashes red every 0.5
seconds
The NAS is in degraded mode (one member drive failed in
RAID 1, RAID 5, or RAID 6).
Flashes green every 0.5
seconds
• The NAS is starting up.
• The NAS is not congured.
• A drive is not formatted.
Green The NAS is ready.
O All drives are in standby mode.
LAN Orange A read/write error occured while another device is
accessing data.
Flashes orange The NAS is being accessed from the network.
Drive Flashes red The data is being accessed and a read/write error occurs
during the process.
Red A drive read/write error occured.
Flashes green The data is being accessed.
Green The drive can be accessed.
TVS-x72XT User Guide
Basic Operations 50
LED Status Description
USB Flashes blue every 0.5 sec • A USB device (connected to the front USB port) is
detected.
• A USB device (connected to the front USB port) is
being removed from the NAS.
• A USB device (connected to the front USB port of the
NAS) is being accessed.
• Data is being copied to or from a USB or eSATA device.
Blue A USB device is detected in the front USB port.
O • No USB device is detected.
• The NAS has nished copying data to or from the USB
device connected to the front USB port.
Audio Alert
Duration Frequency Description
Short beep (0.5 seconds) 1 • The NAS is starting up.
• The NAS is shutting down (software shutdown).
• The user pressed the Reset button.
• The operating system was updated.
3 The user tried to copy the NAS data to the external
storage device from the front USB port, but the data
cannot be copied.
Long beep (1.5 seconds) 3 (every 5 minutes) The system fan is not functioning.
2 • The disk volume is about to reach its full
capacity.
• The disk volume has reached its full capacity.
• The drives are in degraded mode.
• The user started the drive rebuilding process.
• A drive is plugged in or out.
1 • The NAS was powered o by force shutdown
(hardware shutdown).
• The NAS was powered on successfully and is
ready.
TVS-x72XT User Guide
Basic Operations 51
5. NAS Migration
You can migrate data and settings from your current NAS to another NAS model with minimal disruptions
by installing all the hard drives from the source NAS to the destination NAS. RAID conguration and other
settings are retained on the destination NAS after migration.
NAS Migration Requirements
You can only migrate drives to specic NAS models, depending on your source NAS. For the list of NAS
models compatible with direct NAS migration, see https://www.qnap.com/go/nas-migration.
Your device must meet the following requirements:
• QTS NAS supports several types of NAS migration:
• ARM NAS to an ARM NAS
• x86 NAS to an x86 NAS
• ARM NAS to an x86 NAS
Note
You cannot migrate from an x86 NAS to an ARM NAS.
• The destination NAS must run on the same QTS version as the source NAS (or later).
• The destination NAS must have sucient free drive bays to accommodate all the drives that you are
migrating from the source NAS.
For NAS models that do not support NAS migration, you can migrate existing data using HBS 3. For details,
see Migrating NAS Data Using HBS 3.
Status and Setting Changes after NAS Migration
The status of NAS data and settings varies after migration.
Data and Settings After NAS Migration
Registered myQNAPcloud name Your registered myQNAPcloud name is not migrated.
Encrypted disk volumes If the NAS does not support le system encryption,
encrypted disk volumes are not migrated.
Warning
To prevent data loss, back up and save the
encryption keys of encrypted disk volumes in
a safe place. You can also choose to decrypt
disk volumes before migration.
TVS-x72XT User Guide
NAS Migration 52
Data and Settings After NAS Migration
Shared folders All shared folders and the downloaded les stored in them
are retained.
Warning
To prevent data loss, back up and save
encryption keys or passwords of encrypted
shared folders in a safe place before
migration.
Important
Folder permissions on the destination NAS
must be recongured after migration.
Network • If the number of network ports or network port
specications on the destination NAS is dierent from
the source NAS, the following network and virtual
settings may change and require reconguration:
port trunking, virtual machines, Thunderbolt, USB
QuickAccess, and more.
• You must recongure network settings when the source
NAS is running on QTS 4.3.5 or earlier versions.
Windows AD conguration Windows AD congurations must be recongured.
Licenses Licenses are not migrated.
Warning
To prevent losing all your software licenses,
QNAP recommends deactivating licenses on
the source NAS before data migration.
Applications If the destination NAS has less RAM than the source NAS,
the following features and applications might not function:
Virtualization Station, Qsirch, and Snapshots.
Services Only services supported by the destination NAS are
available.
Multimedia features Some multimedia features are disabled by default.
Migrating a NAS
Important
Before performing NAS migration, ensure that you understand all requirements and
possible changes after migration.
For details see the following topics:
•NAS Migration Requirements
•Status and Setting Changes After NAS Migration
1. Power o the source NAS and the destination NAS.
2. Remove the drives.
Important
QNAP recommends following the source NAS drive order when installing the drives. Take note
of the drive tray order when removing the drives.
TVS-x72XT User Guide
NAS Migration 53
a. Remove the drives from the source NAS.
b. Remove the drive trays from the destination NAS.
3. Install the drives.
a. Install source NAS drives onto the destination NAS drive trays.
b. Insert the drive trays into the destination NAS.
4. Power on the destination NAS.
5. Log on to QTS as an administrator on the destination NAS.
The destination NAS automatically checks for the latest rmware update.
Migrating NAS Data Using HBS 3
For NAS models that do not support direct migration, you can initialize the destination NAS then copy data
from the source NAS to the destination NAS using HBS 3.
Preparing the Destination NAS
1. Log on to QTS.
2. Create one or more storage pools.
For details, see the Creating a Storage Pool topic in the QTS user guide.
3. Create one or more volumes.
For details, see the Volume Creation topic in the QTS user guide.
4. Create shared folders on the destination NAS.
For details, see the Creating a Shared Folder topic in the QTS user guide.
5. Install HBS 3 onto the destination NAS.
a. Go to App Center.
b. Search for HBS 3.
c. Click Install.
HBS 3 is installed on the destination NAS.
6. Enable the remote server settings on the destination NAS.
a. Go to App Center > HBS 3 > Services > RTRR Server .
b. Click Enable RTRR Server.
The RTRR server settings window appears.
c. Specify the RTRR Server settings.
TVS-x72XT User Guide
NAS Migration 54
Setting Description
Password Specify a password that contains 1 to 16 characters from any of the
following groups:
• Letters: A to Z, a to z
• Numbers: 0 to 9
• Special characters: . - _ ~ ! @ # $ % ^ & ( ) { }
• Does not start or end with a space.
Port Specify a port number to access the RTRR server.
7. Click Apply.
A conrmation window appears.
8. Click OK.
The remote server settings are completed.
Creating a One-Way Sync Job
1. On the source NAS, go to App Center > HBS 3 > Sync .
2. Click Sync Now.
3. Select One-way Sync Job.
The Create a Sync Job window appears.
4. Click Remote NAS.
5. Click Add New Account.
The Create a Storage Space window appears.
6. Select the destination NAS as the destination storage space and specify the following:
Setting Description
Name The name used to identify the storage space.
IP address / Host name The IP address or hostname used to access the storage space.
Tip
Click to scan for available devices.
Port The port number used to access the storage space.
This value must be between 1 to 65535.
Password The password used to access the storage space.
Use SSL connection Requires SSL connection when accessing the remote NAS.
7. Optional: Test the connection.
Test Description
Detect Server Tests the accessibility of the selected storage space.
Speed Test Tests the network connection speed of the selected storage space.
8. Click Create.
9. Click Select.
TVS-x72XT User Guide
NAS Migration 55
10. Select the paired folders.
Important
• All subfolders and les in the selected folder are selected.
• You can only sync up to 16 paired folders per job.
a. Under the source, click .
A dialog box opens.
b. Select a folder.
c. Click OK.
The dialog box closes.
d. Under the destination, click .
A dialog box opens.
e. Select a folder.
f. Click OK.
g. Optional: Add more paired folders if necessary.
11. Click Next.
The Schedule screen appears.
12. Select Sync now.
13. Click Next.
The Rules screen appears.
14. Optional: Congure job rules.
15. Click Next.
The Summary screen appears.
16. Review the job summary.
17. Click Create.
The source NAS runs the created one-way sync job.
Note
It may take several minutes to migrate shared folders from the source NAS to the destination
NAS.
Importing Local Users or Group Settings to the Destination NAS
1. Power on the source NAS.
2. Back up the users or group settings from the source NAS.
a. Log on to QTS.
b. Go to Control Panel > Privilege > Users .
c. Click Create, and then click Import/Export Users.
The Import/Export Users window appears.
TVS-x72XT User Guide
NAS Migration 56
d. Select Export user and user group settings.
e. Click Next.
The NAS user and user group settings are exported as a le and downloaded onto your computer.
3. Import user settings on the source NAS to the destination NAS.
a. On the destination NAS, log on to QTS.
b. Go to Control Panel > Privilege > Users .
c. Click Create, and then click Import/Export Users.
d. Select Import user and user group settings.
Note
You can select whether to send a notication mail to newly created users or overwrite duplicate
users.
e. On your computer, select the user settings le exported from the source NAS.
The source NAS user settings le is imported to the destination NAS.
TVS-x72XT User Guide
NAS Migration 57
6. Troubleshooting
This chapter describes basic troubleshooting information.
Forcing Qnder Pro or myQNAPcloud to Locate the NAS
If Qnder Pro or myQNAPcloud is unable to locate the NAS during QTS installation, the drives or data may
be faulty.
1. Power o the NAS.
2. Remove all drives.
3. Power on the NAS.
4. Locate the NAS using Qnder Pro or myQNAPcloud.
5. Reinsert the drives.
6. Continue with the QTS installation.
Hot-swapping Failed Drives
The NAS supports hot-swapping of drives in the following situations:
• RAID 1: One member drive fails
• RAID 5: One member drive fails
• RAID 6: One or two member drives fail
1. Log on to QTS.
2. Go to Main Menu > Storage & Snapshots > Storage > Disks/VJBOD .
3. Locate the failed drive.
4. Prepare a new hard drive with a capacity that is the same as or larger than the failed hard drive.
5. Remove the failed drive from the NAS.
6. Wait for 20 seconds or until the NAS beeps twice.
7. Remove the failed drive from the drive tray.
8. Insert the new drive into the drive tray.
9. Install the new drive.
The NAS beeps twice.
10. Go to Main Menu > Storage & Snapshots > Storage > Storage/Snapshots .
11. Locate the volume that contains the new drive and then verify that the status is Rebuilding.
Support and Other Resources
QNAP provides the following resources:
TVS-x72XT User Guide
Troubleshooting 58
7. Glossary
CloudKey
Unique 8-digit code assigned to each NAS device
CloudLink
Enables you to access the NAS over the internet without conguring complex port forwarding settings
myQNAPcloud
Provides various remote access services such as DDNS and CloudLink
myQNAPcloud ID
Email address that was used to register for a myQNAPcloud account
Qnder Pro
Enables you to locate and access the QNAP NAS devices in your local area network
QTS
QNAP NAS operating system
TVS-x72XT User Guide
Glossary 60
8. Notices
This chapter provides information about warranty, disclaimers, licensing, and federal regulations.
Limited Warranty
QNAP oers limited warranty service on our products. Your QNAP-branded hardware product is warranted
against defects in materials and workmanship for a period of one (1) year or more from the date printed on
the invoice. ("Warranty Period"). Please review your statutory rights at www.qnap.com/warranty, which may
be amended from time to time by QNAP in its discretion.
Disclaimer
Information in this document is provided in connection with products of QNAP Systems, Inc. (the "QNAP").
No license, express or implied, by estoppels or otherwise, to any intellectual property rights is granted by
this document. Except as provided in QNAP's terms and conditions of sale for such products, QNAP assumes
no liability whatsoever, and QNAP disclaims any express or implied warranty, relating to sale and/or use of
QNAP products including liability or warranties relating to tness for a particular purpose, merchantability,
or infringement of any patent, copyright or other intellectual property right.
QNAP products are not intended for use in medical, life saving, life sustaining, critical control or safety
systems, or in nuclear facility applications.
In no event shall QNAP’s liability exceed the price paid for the product from direct, indirect, special,
incidental, or consequential damages resulting from the use of the product, its accompanying software,
or its documentation.QNAP makes no warranty or representation, expressed, implied, or statutory, with
respect to its products or the contents or use of this documentation and all accompanying software, and
specically disclaims its quality, performance, merchantability, or tness for any particular purpose. QNAP
reserves the right to revise or update its products, software, or documentation without obligation to notify
any individual or entity.
Back up the system periodically to avoid any potential data loss is recommended. QNAP disclaims any
responsibility of all sorts of data loss or recovery.
Should you return any components of the package of QNAP products such as NAS (Network Attached
Storage) for refund or maintenance, make sure they are carefully packed for shipping. Any form of damages
due to improper packaging will not be compensated.
All the features, functionality, and other product specications are subject to change without prior notice or
obligation. Information contained herein is subject to change without notice.
Further, the ® or ™ symbols are not used in the text.
GNU Public License
Version 3, 29 June 2007
Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not
allowed.
Preamble
The GNU General Public License is a free, copy left license for software and other kinds of works.
The licenses for most software and other practical works are designed to take away your freedom to share
and change the works. By contrast, the GNU General Public License is intended to guarantee your freedom
to share and change all versions of a program--to make sure it remains free software for all its users. We,
TVS-x72XT User Guide
Notices 61
the Free Software Foundation, use the GNU General Public License for most of our software; it applies also
to any other work released this way by its authors. You can apply it to your programs, too.
When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are
designed to make sure that you have the freedom to distribute copies of free software (and charge for them
if you wish), that you receive source code or can get it if you want it, that you can change the software or use
pieces of it in new free programs, and that you know you can do these things.
To protect your rights, we need to prevent others from denying you these rights or asking you to surrender
the rights. Therefore, you have certain responsibilities if you distribute copies of the software, or if you
modify it: responsibilities to respect the freedom of others.
For example, if you distribute copies of such a program, whether gratis or for a fee, you must pass on to the
recipients the same freedoms that you received. You must make sure that they, too, receive or can get the
source code. And you must show them these terms so they know their rights.
Developers that use the GNU GPL protect your rights with two steps: (1) assert copyright on the software,
and (2) oer you this License giving you legal permission to copy, distribute and/or modify it.
For the developers' and authors' protection, the GPL clearly explains that there is no warranty for this free
software. For both users' and authors' sake, the GPL requires that modied versions be marked as changed,
so that their problems will not be attributed erroneously to authors of previous versions.
Some devices are designed to deny users access to install or run modied versions of the software inside
them, although the manufacturer can do so. This is fundamentally incompatible with the aim of protecting
users' freedom to change the software. The systematic pattern of such abuse occurs in the area of products
for individuals to use, which is precisely where it is most unacceptable. Therefore, we have designed this
version of the GPL to prohibit the practice for those products. If such problems arise substantially in other
domains, we stand ready to extend this provision to those domains in future versions of the GPL, as needed
to protect the freedom of users.
Finally, every program is threatened constantly by software patents. States should not allow patents to
restrict development and use of software on general-purpose computers, but in those that do, we wish to
avoid the special danger that patents applied to a free program could make it eectively proprietary. To
prevent this, the GPL assures that patents cannot be used to render the program non-free.
The precise terms and conditions for copying, distribution and modication follow.
Terms and Conditions
1. Denitions.
“This License” refers to version 3 of the GNU General Public License.
“Copyright” also means copyright-like laws that apply to other kinds of works, such as semiconductor
masks.
“The Program” refers to any copyrightable work licensed under this License. Each licensee is addressed
as “you”. “Licensees” and “recipients” may be individuals or organizations.
To “modify” a work means to copy from or adapt all or part of the work in a fashion requiring copyright
permission, other than the making of an exact copy. The resulting work is called a “modied version” of
the earlier work or a work “based on” the earlier work.
A “covered work” means either the unmodied Program or a work based on the Program.
To “propagate” a work means to do anything with it that, without permission, would make you
directly or secondarily liable for infringement under applicable copyright law, except executing it on
a computer or modifying a private copy. Propagation includes copying, distribution (with or without
modication), making available to the public, and in some countries other activities as well.
To “convey” a work means any kind of propagation that enables other parties to make or receive
copies. Mere interaction with a user through a computer network, with no transfer of a copy, is not
conveying.
An interactive user interface displays “Appropriate Legal Notices” to the extent that it includes a
convenient and prominently visible feature that (1) displays an appropriate copyright notice, and (2)
TVS-x72XT User Guide
Notices 62
tells the user that there is no warranty for the work (except to the extent that warranties are provided),
that licensees may convey the work under this License, and how to view a copy of this License. If the
interface presents a list of user commands or options, such as a menu, a prominent item in the list
meets this criterion.
2. Source Code.
The “source code” for a work means the preferred form of the work for making modications to it.
“Object code” means any non-source form of a work.
A “Standard Interface” means an interface that either is an ocial standard dened by a recognized
standards body, or, in the case of interfaces specied for a particular programming language, one that
is widely used among developers working in that language.
The “System Libraries” of an executable work include anything, other than the work as a whole, that (a)
is included in the normal form of packaging a Major Component, but which is not part of that Major
Component, and (b) serves only to enable use of the work with that Major Component, or to implement
a Standard Interface for which an implementation is available to the public in source code form. A
“Major Component”, in this context, means a major essential component (kernel, window system, and
so on) of the specic operating system (if any) on which the executable work runs, or a compiler used
to produce the work, or an object code interpreter used to run it.
The “Corresponding Source” for a work in object code form means all the source code needed to
generate, install, and (for an executable work) run the object code and to modify the work, including
scripts to control those activities. However, it does not include the work's System Libraries, or general-
purpose tools or generally available free programs which are used unmodied in performing those
activities but which are not part of the work. For example, Corresponding Source includes interface
denition les associated with source les for the work, and the source code for shared libraries and
dynamically linked subprograms that the work is specically designed to require, such as by intimate
data communication or control ow between those subprograms and other parts of the work.
The Corresponding Source need not include anything that users can regenerate automatically from
other parts of the Corresponding Source.
The Corresponding Source for a work in source code form is that same work.
3. Basic Permissions.
All rights granted under this License are granted for the term of copyright on the Program, and
are irrevocable provided the stated conditions are met. This License explicitly arms your unlimited
permission to run the unmodied Program. The output from running a covered work is covered by this
License only if the output, given its content, constitutes a covered work. This License acknowledges
your rights of fair use or other equivalent, as provided by copyright law.
You may make, run and propagate covered works that you do not convey, without conditions so
long as your license otherwise remains in force. You may convey covered works to others for the
sole purpose of having them make modications exclusively for you, or provide you with facilities for
running those works, provided that you comply with the terms of this License in conveying all material
for which you do not control copyright. Those thus making or running the covered works for you must
do so exclusively on your behalf, under your direction and control, on terms that prohibit them from
making any copies of your copyrighted material outside their relationship with you.
Conveying under any other circumstances is permitted solely under the conditions stated below.
Sublicensing is not allowed; section 10 makes it unnecessary.
4. Protecting Users' Legal Rights From Anti-Circumvention Law.
No covered work shall be deemed part of an eective technological measure under any applicable law
fullling obligations under article 11 of the WIPO copyright treaty adopted on 20 December 1996, or
similar laws prohibiting or restricting circumvention of such measures.
When you convey a covered work, you waive any legal power to forbid circumvention of technological
measures to the extent such circumvention is eected by exercising rights under this License with
respect to the covered work, and you disclaim any intention to limit operation or modication of the
work as a means of enforcing, against the work's users, your or third parties' legal rights to forbid
circumvention of technological measures.
5. Conveying Verbatim Copies.
TVS-x72XT User Guide
Notices 63
You may convey verbatim copies of the Program's source code as you receive it, in any medium,
provided that you conspicuously and appropriately publish on each copy an appropriate copyright
notice; keep intact all notices stating that this License and any non-permissive terms added in accord
with section 7 apply to the code; keep intact all notices of the absence of any warranty; and give all
recipients a copy of this License along with the Program.
You may charge any price or no price for each copy that you convey, and you may oer support or
warranty protection for a fee.
6. Conveying Modied Source Versions.
You may convey a work based on the Program, or the modications to produce it from the Program,
in the form of source code under the terms of section 4, provided that you also meet all of these
conditions:
a. The work must carry prominent notices stating that you modied it, and giving a relevant date.
b. The work must carry prominent notices stating that it is released under this License and any
conditions added under section 7. This requirement modies the requirement in section 4 to
“keep intact all notices”.
c. You must license the entire work, as a whole, under this License to anyone who comes into
possession of a copy. This License will therefore apply, along with any applicable section 7
additional terms, to the whole of the work, and all its parts, regardless of how they are packaged.
This License gives no permission to license the work in any other way, but it does not invalidate
such permission if you have separately received it.
d. If the work has interactive user interfaces, each must display Appropriate Legal Notices; however,
if the Program has interactive interfaces that do not display Appropriate Legal Notices, your work
need not make them do so.
A compilation of a covered work with other separate and independent works, which are not by
their nature extensions of the covered work, and which are not combined with it such as to form
a larger program, in or on a volume of a storage or distribution medium, is called an “aggregate”
if the compilation and its resulting copyright are not used to limit the access or legal rights of the
compilation's users beyond what the individual works permit. Inclusion of a covered work in an
aggregate does not cause this License to apply to the other parts of the aggregate.
7. Conveying Non-Source Forms.
You may convey a covered work in object code form under the terms of sections 4 and 5, provided that
you also convey the machine-readable Corresponding Source under the terms of this License, in one of
these ways:
a. Convey the object code in, or embodied in, a physical product (including a physical distribution
medium), accompanied by the Corresponding Source xed on a durable physical medium
customarily used for software interchange.
b. Convey the object code in, or embodied in, a physical product (including a physical distribution
medium), accompanied by a written oer, valid for at least three years and valid for as long
as you oer spare parts or customer support for that product model, to give anyone who
possesses the object code either (1) a copy of the Corresponding Source for all the software in
the product that is covered by this License, on a durable physical medium customarily used for
software interchange, for a price no more than your reasonable cost of physically performing this
conveying of source, or (2) access to copy the Corresponding Source from a network server at no
charge.
c. Convey individual copies of the object code with a copy of the written oer to provide the
Corresponding Source. This alternative is allowed only occasionally and noncommercially, and
only if you received the object code with such an oer, in accord with subsection 6b.
d. Convey the object code by oering access from a designated place (gratis or for a charge), and
oer equivalent access to the Corresponding Source in the same way through the same place
TVS-x72XT User Guide
Notices 64
at no further charge. You need not require recipients to copy the Corresponding Source along
with the object code. If the place to copy the object code is a network server, the Corresponding
Source may be on a dierent server (operated by you or a third party) that supports equivalent
copying facilities, provided you maintain clear directions next to the object code saying where to
nd the Corresponding Source. Regardless of what server hosts the Corresponding Source, you
remain obligated to ensure that it is available for as long as needed to satisfy these requirements.
e. Convey the object code using peer-to-peer transmission, provided you inform other peers where
the object code and Corresponding Source of the work are being oered to the general public at
no charge under subsection 6d.
A separable portion of the object code, whose source code is excluded from the Corresponding
Source as a System Library, need not be included in conveying the object code work.
A “User Product” is either (1) a “consumer product”, which means any tangible personal property
which is normally used for personal, family, or household purposes, or (2) anything designed or
sold for incorporation into a dwelling. In determining whether a product is a consumer product,
doubtful cases shall be resolved in favor of coverage. For a particular product received by a
particular user, “normally used” refers to a typical or common use of that class of product,
regardless of the status of the particular user or of the way in which the particular user actually
uses, or expects or is expected to use, the product. A product is a consumer product regardless
of whether the product has substantial commercial, industrial or non-consumer uses, unless such
uses represent the only signicant mode of use of the product.
“Installation Information” for a User Product means any methods, procedures, authorization keys,
or other information required to install and execute modied versions of a covered work in that
User Product from a modied version of its Corresponding Source. The information must suce
to ensure that the continued functioning of the modied object code is in no case prevented or
interfered with solely because modication has been made.
If you convey an object code work under this section in, or with, or specically for use in, a User
Product, and the conveying occurs as part of a transaction in which the right of possession and
use of the User Product is transferred to the recipient in perpetuity or for a xed term (regardless
of how the transaction is characterized), the Corresponding Source conveyed under this section
must be accompanied by the Installation Information. But this requirement does not apply if
neither you nor any third party retains the ability to install modied object code on the User
Product (for example, the work has been installed in ROM).
The requirement to provide Installation Information does not include a requirement to continue
to provide support service, warranty, or updates for a work that has been modied or installed
by the recipient, or for the User Product in which it has been modied or installed. Access
to a network may be denied when the modication itself materially and adversely aects the
operation of the network or violates the rules and protocols for communication across the
network.
Corresponding Source conveyed, and Installation Information provided, in accord with this
section must be in a format that is publicly documented (and with an implementation available
to the public in source code form), and must require no special password or key for unpacking,
reading or copying.
8. Additional Terms.
“Additional permissions” are terms that supplement the terms of this License by making exceptions
from one or more of its conditions. Additional permissions that are applicable to the entire Program
shall be treated as though they were included in this License, to the extent that they are valid under
applicable law. If additional permissions apply only to part of the Program, that part may be used
separately under those permissions, but the entire Program remains governed by this License without
regard to the additional permissions.
When you convey a copy of a covered work, you may at your option remove any additional permissions
from that copy, or from any part of it. (Additional permissions may be written to require their own
removal in certain cases when you modify the work.) You may place additional permissions on
material, added by you to a covered work, for which you have or can give appropriate copyright
permission.
TVS-x72XT User Guide
Notices 65
Notwithstanding any other provision of this License, for material you add to a covered work, you may
(if authorized by the copyright holders of that material) supplement the terms of this License with
terms:
a. Disclaiming warranty or limiting liability dierently from the terms of sections 15 and 16 of this
License; or
b. Requiring preservation of specied reasonable legal notices or author attributions in that
material or in the Appropriate Legal Notices displayed by works containing it; or
c. Prohibiting misrepresentation of the origin of that material, or requiring that modied versions of
such material be marked in reasonable ways as dierent from the original version; or
d. Limiting the use for publicity purposes of names of licensors or authors of the material; or
e. Declining to grant rights under trademark law for use of some trade names, trademarks, or
service marks; or
f. Requiring indemnication of licensors and authors of that material by anyone who conveys the
material (or modied versions of it) with contractual assumptions of liability to the recipient, for
any liability that these contractual assumptions directly impose on those licensors and authors.
All other non-permissive additional terms are considered “further restrictions” within the
meaning of section 10. If the Program as you received it, or any part of it, contains a notice
stating that it is governed by this License along with a term that is a further restriction, you may
remove that term. If a license document contains a further restriction but permits relicensing or
conveying under this License, you may add to a covered work material governed by the terms of
that license document, provided that the further restriction does not survive such relicensing or
conveying.
If you add terms to a covered work in accord with this section, you must place, in the relevant
source les, a statement of the additional terms that apply to those les, or a notice indicating
where to nd the applicable terms.
Additional terms, permissive or non-permissive, may be stated in the form of a separately written
license, or stated as exceptions; the above requirements apply either way.
9. Termination.
You may not propagate or modify a covered work except as expressly provided under this License. Any
attempt otherwise to propagate or modify it is void, and will automatically terminate your rights under
this License (including any patent licenses granted under the third paragraph of section 11).
However, if you cease all violation of this License, then your license from a particular copyright holder
is reinstated (a) provisionally, unless and until the copyright holder explicitly and nally terminates
your license, and (b) permanently, if the copyright holder fails to notify you of the violation by some
reasonable means prior to 60 days after the cessation.
Moreover, your license from a particular copyright holder is reinstated permanently if the copyright
holder noties you of the violation by some reasonable means, this is the rst time you have received
notice of violation of this License (for any work) from that copyright holder, and you cure the violation
prior to 30 days after your receipt of the notice.
Termination of your rights under this section does not terminate the licenses of parties who have
received copies or rights from you under this License. If your rights have been terminated and not
permanently reinstated, you do not qualify to receive new licenses for the same material under section
10.
10. Acceptance Not Required for Having Copies.
You are not required to accept this License in order to receive or run a copy of the Program. Ancillary
propagation of a covered work occurring solely as a consequence of using peer-to-peer transmission to
receive a copy likewise does not require acceptance. However, nothing other than this License grants
you permission to propagate or modify any covered work. These actions infringe copyright if you do
not accept this License. Therefore, by modifying or propagating a covered work, you indicate your
acceptance of this License to do so.
TVS-x72XT User Guide
Notices 66
11. Automatic Licensing of Downstream Recipients.
Each time you convey a covered work, the recipient automatically receives a license from the original
licensors, to run, modify and propagate that work, subject to this License. You are not responsible for
enforcing compliance by third parties with this License.
An “entity transaction” is a transaction transferring control of an organization, or substantially all assets
of one, or subdividing an organization, or merging organizations. If propagation of a covered work
results from an entity transaction, each party to that transaction who receives a copy of the work also
receives whatever licenses to the work the party's predecessor in interest had or could give under
the previous paragraph, plus a right to possession of the Corresponding Source of the work from the
predecessor in interest, if the predecessor has it or can get it with reasonable eorts.
You may not impose any further restrictions on the exercise of the rights granted or armed under
this License. For example, you may not impose a license fee, royalty, or other charge for exercise
of rights granted under this License, and you may not initiate litigation (including a cross-claim or
counterclaim in a lawsuit) alleging that any patent claim is infringed by making, using, selling, oering
for sale, or importing the Program or any portion of it.
12. Patents.
A “contributor” is a copyright holder who authorizes use under this License of the Program or a work
on which the Program is based. The work thus licensed is called the contributor's “contributor version”.
A contributor's “essential patent claims” are all patent claims owned or controlled by the contributor,
whether already acquired or hereafter acquired, that would be infringed by some manner, permitted
by this License, of making, using, or selling its contributor version, but do not include claims that would
be infringed only as a consequence of further modication of the contributor version. For purposes of
this denition, “control” includes the right to grant patent sublicenses in a manner consistent with the
requirements of this License.
Each contributor grants you a non-exclusive, worldwide, royalty-free patent license under the
contributor's essential patent claims, to make, use, sell, oer for sale, import and otherwise run,
modify and propagate the contents of its contributor version.
In the following three paragraphs, a “patent license” is any express agreement or commitment,
however denominated, not to enforce a patent (such as an express permission to practice a patent
or covenant not to sue for patent infringement). To “grant” such a patent license to a party means to
make such an agreement or commitment not to enforce a patent against the party.
If you convey a covered work, knowingly relying on a patent license, and the Corresponding Source
of the work is not available for anyone to copy, free of charge and under the terms of this License,
through a publicly available network server or other readily accessible means, then you must either (1)
cause the Corresponding Source to be so available, or (2) arrange to deprive yourself of the benet of
the patent license for this particular work, or (3) arrange, in a manner consistent with the requirements
of this License, to extend the patent license to downstream recipients. “Knowingly relying” means you
have actual knowledge that, but for the patent license, your conveying the covered work in a country,
or your recipient's use of the covered work in a country, would infringe one or more identiable
patents in that country that you have reason to believe are valid.
If, pursuant to or in connection with a single transaction or arrangement, you convey, or propagate by
procuring conveyance of, a covered work, and grant a patent license to some of the parties receiving
the covered work authorizing them to use, propagate, modify or convey a specic copy of the covered
work, then the patent license you grant is automatically extended to all recipients of the covered work
and works based on it.
A patent license is “discriminatory” if it does not include within the scope of its coverage, prohibits
the exercise of, or is conditioned on the non-exercise of one or more of the rights that are specically
granted under this License. You may not convey a covered work if you are a party to an arrangement
with a third party that is in the business of distributing software, under which you make payment to
the third party based on the extent of your activity of conveying the work, and under which the third
party grants, to any of the parties who would receive the covered work from you, a discriminatory
patent license (a) in connection with copies of the covered work conveyed by you (or copies made from
those copies), or (b) primarily for and in connection with specic products or compilations that contain
the covered work, unless you entered into that arrangement, or that patent license was granted, prior
to 28 March 2007.
TVS-x72XT User Guide
Notices 67
Nothing in this License shall be construed as excluding or limiting any implied license or other
defenses to infringement that may otherwise be available to you under applicable patent law.
13. No Surrender of Others' Freedom.
If conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the
conditions of this License, they do not excuse you from the conditions of this License. If you cannot
convey a covered work so as to satisfy simultaneously your obligations under this License and any
other pertinent obligations, then as a consequence you may not convey it at all. For example, if you
agree to terms that obligate you to collect a royalty for further conveying from those to whom you
convey the Program, the only way you could satisfy both those terms and this License would be to
refrain entirely from conveying the Program.
14. Use with the GNU Aero General Public License.
Notwithstanding any other provision of this License, you have permission to link or combine any
covered work with a work licensed under version 3 of the GNU Aero General Public License into a
single combined work, and to convey the resulting work. The terms of this License will continue to
apply to the part which is the covered work, but the special requirements of the GNU Aero General
Public License, section 13, concerning interaction through a network will apply to the combination as
such.
15. Revised Versions of this License.
The Free Software Foundation may publish revised and/or new versions of the GNU General Public
License from time to time. Such new versions will be similar in spirit to the present version, but may
dier in detail to address new problems or concerns.
Each version is given a distinguishing version number. If the Program species that a certain
numbered version of the GNU General Public License “or any later version” applies to it, you have
the option of following the terms and conditions either of that numbered version or of any later
version published by the Free Software Foundation. If the Program does not specify a version number
of the GNU General Public License, you may choose any version ever published by the Free Software
Foundation.
If the Program species that a proxy can decide which future versions of the GNU General Public
License can be used, that proxy's public statement of acceptance of a version permanently authorizes
you to choose that version for the Program.
Later license versions may give you additional or dierent permissions. However, no additional
obligations are imposed on any author or copyright holder as a result of your choosing to follow a
later version.
16. Disclaimer of Warranty.
THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW.
EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES
PROVIDE THE PROGRAM “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE
PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL
NECESSARY SERVICING, REPAIR OR CORRECTION.
17. Limitation of Liability.
IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY
COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MODIFIES AND/OR CONVEYS THE PROGRAM
AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE
PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE
OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE
WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
18. Interpretation of Sections 16 and 17.
TVS-x72XT User Guide
Notices 68
If the disclaimer of warranty and limitation of liability provided above cannot be given local legal eect
according to their terms, reviewing courts shall apply local law that most closely approximates an
absolute waiver of all civil liability in connection with the Program, unless a warranty or assumption of
liability accompanies a copy of the Program in return for a fee.
END OF TERMS AND CONDITIONS
CE Notice
This QNAP NAS complies with CE Compliance Class B.
UKCA Notice
This device complies with the UKCA requirements for products sold in Great Britain.
FCC Notice
FCC Class B Notice
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired
operation.
Note
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment o and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
TVS-x72XT User Guide
Notices 69
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/television technician for help.
Important
Any modications made to this device that are not approved by QNAP Systems, Inc. may
void the authority granted to the user by the FCC to operate this equipment.
VCCI Notice
VCCI–B
BSMI Notice
SJ/T 11364-2006
本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符合中国 RoHS
标准规定的限量要求。
本产品上会附有”环境友好使用期限”的标签，此期限是估算这些物质”不会有泄漏或突变”的年限。本产品可能
包含有较短的环境友好使用期限的可替换元件，像是电池或灯管，这些元件将会单独标示出来。
TVS-x72XT User Guide
Notices 70
部件名称 有毒有害物质或元素
铅
(Pb)
汞
(Hg)
镉
(Cd)
六价铬
(CR(VI))
多溴联苯
(PBB)
多溴二苯醚
(PBDE)
壳体 0 0 0 0 0 0
显示 0 0 0 0 0 0
印刷电路板 0 0 0 0 0 0
金属螺帽 0 0 0 0 0 0
电缆组装 0 0 0 0 0 0
风扇组装 0 0 0 0 0 0
电力供应组装 0 0 0 0 0 0
电池 0 0 0 0 0 0
O: 表示该有毒有害物质在该部件所有物质材料中的含量均在 SJ/T11363-2006 标准规定的限量要求以下。
X: 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T11363-2006 标准规定的限量要求。
TVS-x72XT User Guide
Notices 71