Salicru SPS 850 LINK M User Manual
Displayed below is the user manual for SPS 850 LINK M by Salicru which is a product in the Uninterruptible Power Supplies (UPSs) category. This manual has pages.
Related Manuals
UNINTERRUPTIBLE POWER SUPPLY (UPS) SYSTEMS
USER MANUAL
2SALICRU
3
General index
1. INTRODUCTION
1.1. THANK-YOU LETTER
2. SAFETY INFORMATION
2.1. USING THIS MANUAL
2.1.1. Conventions and symbols
3. QUALITY ASSURANCE
AND STANDARDS
3.1. MANAGEMENT STATEMENT
3.2. STANDARDS
3.3. ENVIRONMENT
4. PRESENTATION
4.1. DIAGRAMS
4.1.1. Unit diagrams
4.1.2. Unit diagram key
4.2. OPERATING PRINCIPLE
4.2.1. Features
5. INSTALLATION
5.1. STORAGE LOCATION AND CONDITIONS
5.2. CONNECTING THE UNIT TO THE MAINS FOR THE FIRST
TIME OR AFTER IT HAS BEEN OUT OF USE FOR TWO
MONTHS
5.3. CONNECTING THE LOADS
5.4. CONNECTING THE COMMUNICATION CABLE
5.5. DOWNLOADING AND INSTALLING THE SOFTWARE
5.6. STARTING UP/STOPPING THE UNIT
5.6.1. Starting up the SPS.LINK
5.6.2. Stopping the SPS.LINK
6. TROUBLESHOOTING GUIDE
7. GENERAL TECHNICAL
SPECIFICATIONS
USER MANUAL SPS.LINK UNINTERRUPTIBLE POWER SUPPLY (UPS) SYSTEMS
4SALICRU
1. INTRODUCTION
1.1. THANK-YOU LETTER
We would like to thank you for purchasing this product. Read
this instruction manual carefully in order to familiarise yourself
with its contents. You will get the most out of the unit, achieve
a higher the degree of satisfaction and guarantee high levels of
safety the more you understand the unit.
Please do not hesitate to contact us for any further information
or any questions you may have.
Yours sincerely,
SALICRU
•The unit described in this manual can cause serious
physical injury if handled incorrectly. Therefore, the
unit must only be installed, serviced and/or repaired by our
staff or by qualified personnel.
•Although every effort has been made to guarantee that the
information in this user manual is complete and accurate,
we are not responsible for any errors or omissions that may
be present.
The images included in this document are for illustrative
purposes only and may not accurately represent the parts
of the unit shown in this manual. However, any differences
will be reduced or resolved through the correct labelling on
the unit.
•In line with our policy of continuous development, we
reserve the right to modify the specifications, oper-
ating principle or actions described in this document
without prior notice.
•The reproduction, copying, transfer to third parties,
modification or translation in full or in part of this
manual or document, in any form or by any means, without
prior written consent from our company, is prohibited,
with us reserving the full and exclusive right of ownership
to it.
5
2. SAFETY INFORMATION
2.1. USING THIS MANUAL
The user manual is available for customers on our website. It
can be read online or downloaded, as appropriate.
In addition to reading the manual, it is necessary to access
document EK266*08, relating to the "Safety instructions".
Please read these instructions carefully before carrying out any
action on the unit in terms of installation or start-up, change of
location, configuration or handling of any type.
The purpose of the user manual is to provide information re-
lating to safety, as well as explanations about the unit's in-
stallation and operating procedures. Read them carefully and
follow the steps in the corresponding order.
Compliance as regards the "Safety instructions"
is mandatory, with the user being legally respon-
sible for observing and applying them.
All units are supplied with the corresponding labels to guar-
antee the correct identification of each part. In addition, the
user can refer to the user manual at any time during installation
or start-up operation, which provides clear, well-organised and
easy-to-understand information.
Finally, once the unit is installed and in operation, we recom-
mend that you keep the documentation in a safe place that is
easy to access, in case of any future queries that may arise.
The following terms are used interchangeably in the document
to refer to:
•"SPS.LINK, equipment, system, unit or UPS".- SPS.
LINK Uninterruptible Power Supply System.
Depending on the context of the sentence, they may refer
interchangeably to the UPS itself or to the UPS and the bat-
teries.
•"Batteries or capacitor banks".- A group or set of ele-
ments that stores the flow of electrons by electrochemical
means.
•"S.T.S.".- Service and Technical Support.
•"customer, installer, operator or user".- They are used
interchangeably and, by extension, to refer to the installer
and/or the operator who will carry out the corresponding
actions, whereby the responsibility for carrying out the
respective actions may be held by the same person when
they act on behalf or in representation of the installer or
operator.
2.1.1. Conventions and symbols
Some symbols may be used and may appear on the unit, bat-
teries and/or in the user manual.
For more information, see section 1.1.1 of document EK266*08
relating to the "Safety Instructions".
USER MANUAL SPS.LINK UNINTERRUPTIBLE POWER SUPPLY (UPS) SYSTEMS
6SALICRU
3. QUALITY ASSURANCE
AND STANDARDS
3.1. MANAGEMENT STATEMENT
Our aim is to satisfy our customers. Management has estab-
lished a Quality and Environmental Policy for such purposes. As a
result, a Quality and Environmental Management System will be
implemented, which will ensure that we are compliant with the
requirements of the ISO 9001 and ISO 14001 standards and that
we meet all customer and stakeholder requirements.
The company management is also committed to the develop-
ment and improvement of the Quality and Environmental Man-
agement System, through:
•Communication to the entire company of the importance of
satisfaction, both in terms of the customer’s requirements,
as well as legal and regulatory requirements.
•Dissemination of the Quality and Environmental Policy and
setting of the Quality and Environment targets.
•Management reviews.
•Provision of the necessary resources.
3.2. STANDARDS
The SPS.LINK product is designed, manufactured and marketed
in accordance with the EN ISO 9001 standard on Quality
Assurance and is certified by SGS. The mark indicates
conformity with the EEC Directives through application of the
following standards:
•2014/35/UE on Low Voltage Safety.
•2014/30/UE on Electromagnetic Compatibility (EMC).
According to the specifications of harmonised standards. Ref-
erence standards:
•EN-IEC 62040-1. Uninterruptible power systems (UPS).
Part 1: General and safety requirements for UPS
used in user access areas.
•EN-IEC 62040-2. Uninterruptible power systems (UPS).
Part 2: Electromagnetic compatibility (EMC) requirements.
The manufacturer shall not be held responsible for any
damage caused by the user after altering or tampering
with the unit in any way.
This product is suitable for use in both single-user
professional and domestic applications.
The EC declaration of conformity for the product is
available for the customer and can be requested from
our head office.
3.3. ENVIRONMENT
This product has been designed with the protection of the en-
vironment in mind and has been manufactured in accordance
with the ISO 14001 standard.
Recycling the unit at the end of its useful life:
Our company commits to using the services of approved com-
panies that comply with the regulations in order to process the
recovered product at the end of its useful life (please contact
your distributor).
Packaging:
To recycle the packaging, follow the applicable legal regula-
tions, depending on the particular standards of the country
where the unit is installed.
Batteries:
The batteries represent a serious health and environmental
risk. They must be disposed of in accordance with the appli-
cable laws.
7
4. PRESENTATION
4.1. DIAGRAMS
4.1.1. Unit diagrams
Figures 1 and 2 show illustrations of the units according to the
model. Nevertheless and as the product is continuously being
developed, there may be slight discrepancies or inconsisten-
cies. Therefore, in the case of any queries, the labels on the unit
will always take precedence.
All of the values for the main specifications or features
can be checked on the unit's name plate. Act accord-
ingly for your installation.
SPS.500÷650.LINK M
SPS.500÷850.LINK M USB
SPS.500÷650.LINK
SPS.500÷850.LINK USB
SPS.1100÷2000.LINK M USB
SPS.1100÷2000.LINK USB
1
4
1
2
3
4
Fig. 1. Front views of SPS.LINK
SPS.1100.LINK M USB SPS.1500÷2000.LINK M USB
SPS.500÷650.LINK M
SPS.500÷850.LINK M USB
10 5 8 7 7 10 8 5 7 8 10 8 5
Fig. 2. Rear views, with IEC sockets.
USER MANUAL SPS.LINK UNINTERRUPTIBLE POWER SUPPLY (UPS) SYSTEMS
8SALICRU
SPS.1100.LINK USB SPS.1500÷2000.LINK USB
SPS.500÷650.LINK
SPS.500÷850.LINK USB
6 10 8 7 6 10 7 8 6 10 9 7 8
Fig. 3. Rear views, with SCHUKO sockets.
4.1.2. Unit diagram key
1. Unit start and stop button.
2. Red LED lit. Unit in the Fail-safe Mode. This LED is also
used to warn the user about the fact that the unit charge
level is too low, when it starts to flash, and with the
same modulation as that of the acoustic alarm.
3. Flashing yellow LED. Unit in the Battery Mode - output
power supply from the internal battery-.
4. Green LED on. Unit in the AC Mode - output power supply
from the input voltage-.
5. IEC socket used to power the unit (only in models
without power cord (6.).
6. Input power cable.
7. Output current sockets
8. USB HID communication port (depending on model).
9. Fan of the unit (only in models SPS.1500÷2000.LINK M
USB and SPS.1500÷2000.LINK USB).
10. Input protection via circuit breaker or fuse, depending
on the model.
CONTENTS
The following is supplied within the unit's packaging:
•SPS.LINK unit.
•Quick guide.
•Warranty leaflet.
•1 USB HID communication cable, depending on model.
•1 output cable (only in models with IEC output).
4.2. OPERATING PRINCIPLE
•It is an Uninterruptible Power Supply (UPS) system with
line-interactive technology that offers the best protec-
tion solution for the units and the information that make
up both domestic and professional IT environments (small
businesses, offices, shops, etc.).
•The use of AVR Boost&Buck technology - permanent stabi-
lisation of the supply voltage - provides a two-fold advan-
tage: higher protection of connected loads, combined with
a reduced use of UPS batteries.
•In the case of a power supply outage, it supplies electrical
power from the batteries to ensure the units continue op-
erating.
•It is also worth mentioning the built-in communication
functions to communicate between the UPS and computer
system through the USB HID port (communication cable
supplied with the unit) and the monitoring software, com-
patible with Windows, Linux, Unix and Mac.
4.2.1. Features
•Line-interactive technology.
•High level of reliability through control by microprocessor.
•AVR Boost&Buck permanent stabilisation.
•USB HID interface, depending on model.
•Monitoring software for Windows, Linux, Unix and Mac.
•A single on/off button for easy and convenient use.
•Protection against overloads, short-circuits and transients.
•Smart battery charger that reduces the average recharging
time.
•Recharging the batteries with the equipment switched off.
•Cold start function using the batteries (not connected to the
mains).
•Automatic start-up after the input voltage is reconnected.
9
5. INSTALLATION
• Read and follow the Safety Information set out in
chapter 2 of this document. Failure to adhere to any of
the indications set out in chapter 2 may cause a serious or
very serious accident for those who are in direct contact
with the unit or who are in the vicinity, as well as faults in
the unit and/or in the loads connected to it.
•Check that the information on the name plate is the right
information for the installation.
•Once you have unpacked the unit, inspect it and ensure that it
is in perfect condition before proceeding. If this is not the case,
please contact your distributor.
• Limitations to the connection and use of the unit ac-
cording to its morphology and sector or work environ-
ment:
For its connection.
–In units with a power supply plug and output
sockets (with no connection terminals).
It can be connected by staff with no specific
technical training; in general, by anyone who
uses household appliances.
For its use.
–Unit with no connection terminals, generally
designed for household environments and, to a
lesser extent, for shops, industry and other sectors.
The unit can be used by staff with no specific
technical training by simply following the in-
structions in the user manual.
•Always bear in mind that the UPS is an electrical gen-
erator, which is why the user must take the necessary
precautions to prevent direct or indirect contact.
5.1. STORAGE LOCATION AND CONDITIONS
•Install the UPS in a protected area that does not have ex-
cessive humidity but has suitable ventilation.
•Place the UPS at a distance of at least 20 cm from other
units to prevent interference.
•Do not operate the unit where the temperature and hu-
midity exceed the permitted limits (see the technical speci-
fications).
20 cm 20 cm
5.2. CONNECTING THE UNIT TO THE MAINS FOR THE
FIRST TIME OR AFTER IT HAS BEEN OUT OF USE
FOR TWO MONTHS
•Insert the plug of the mains cable (6.) into an AC socket.
•For the best results, charge the battery for at least 4 hours
before using the unit for the first time or when it has been
out of use for more than two months.
Otherwise, the SPS.LINK may not react in a
satisfactory way if there is an outage during
the initial operating hours. Its response ca-
pacity during unexpected AC power supply
failures is dependent on the energy accumu-
lated in the battery.
•The battery charges by simply connecting
the unit to the mains.
5.3. CONNECTING THE LOADS
•Connect the loads to the output sockets 6 on the rear
of the unit.
• Never connect a laser printer or
scanner to the UPS. This may
damage the unit and/or consume the energy
stored in the batteries, which is reserved for
other more sensitive and more important
types of loads.
5.4. CONNECTING THE COMMUNICATION CABLE
•To enable unattended start-up/stop of the UPS and to mon-
itor its status, connect one end of the communication cable
to the connector 8 of the USB HID port of SPS.LINK and the
other end to the communication port of the PC.
•With the monitoring software installed in your PC, you can
programme the UPS start-up/stopping time, as well as
monitor its status in real time. Follow the steps described
below before downloading and installing the monitoring
software.
USER MANUAL SPS.LINK UNINTERRUPTIBLE POWER SUPPLY (UPS) SYSTEMS
10 SALICRU
5.5. DOWNLOADING AND INSTALLING THE
SOFTWARE
•To download the free monitoring software, register as a
user and then register your unit(s) at the following site:
support.salicru.com
•You will find a link to the "ACTIVATION GUIDE" on the reg-
istration page. Follow the steps indicated.
•Once you have registered, you can download the software
for each model from the site:
support.salicru.com/software
•Use with your installation as with any other type of soft-
ware.
•When you reboot your PC, the monitoring software will ap-
pear as an orange icon on the system tray, next to the clock.
5.6. STARTING UP/STOPPING THE UNIT
5.6.1. Starting up the SPS.LINK
•With SPS.LINK stopped, press the button 1 to start the unit.
•When the unit is started, an internal test is performed and
all LEDs are turned on. The process takes a few seconds,
after which the UPS will supply an output voltage, either
from the mains or from its batteries.
The auto-test will be performed regardless of whether the
start-up process is carried out with the unit connected to
the mains or running on its batteries (no mains connection).
•Start up the loads.
5.6.2. Stopping the SPS.LINK
•Stopping the loads.
•Switch the unit off, press the button 1.
11
6. TROUBLESHOOTING GUIDE
Use the following table to resolve minor issues:
Problem Possible cause Solutions
No LED is lit on
the front panel.
Low battery. Charge the UPS for at least 6
hours.
Battery fault. Replace the battery with the
same model.
The UPS is not ON. Press the UPS start-up button
again.
The alarm
sounds
continuously
when connected
to the mains.
The UPS is
overloaded.
First, disconnect a few loads.
Before starting it up again,
check that the connected load
matches the unit's power
specifications.
In the case of
a problem in
the mains, the
operating time
is very short.
The UPS is
overloaded. Disconnect critical loads.
Battery voltage is
too low.
Charge the UPS for at least 6
hours.
Defective battery. It
may be due to the
ambient temperature
or inappropriate
operation.
Replace the battery with the
same model.
There are no
problems in the
mains but the
unit is in battery
mode.
The mains cable plug
is not connected
correctly.
Reconnect the mains cable
plug correctly.
Tabla 1. Troubleshooting table.
•If you are registered on the website:
support.salicru.com
, you can access:
support.salicru.com/troubleshooting
, to consult the extended troubleshooting guide of the unit,
in addition to accessing other services available for regis-
tered users.
USER MANUAL SPS.LINK UNINTERRUPTIBLE POWER SUPPLY (UPS) SYSTEMS
12 SALICRU
7. GENERAL TECHNICAL
SPECIFICATIONS
MODEL 500 650 850 1100 1500 2000
Power (VA) 500 700 900 1100 1500 2000
Power (W) 240 360 480 660 900 1200
Technology Line-interactive
INPUT
Voltage 230 VAC.
Margins Up to 170÷280 VAC ± 5%
Nominal frequency 50 / 60 Hz.
Frequency auto-
detect Yes.
Stabilisation AVR buck/boost.
OUTPUT
Voltage (VAC) 230 VAC.
Voltage accuracy(1) ± 10 %.
Frequency(1) 50 / 60 ± 1 Hz.
Waveform(1) Pseudo-sine (simulated sine).
Available socket
types IEC and SCHUKO.
Transfer time standard 2-6 ms, maximum 10 ms.
PROTECTION
Input Thermal self-resetting or fuse (according to the
model).
Complete
protection
Overload, battery discharged and overcurrent in
the charging device.
BATTERY
Type Sealed Pb-Ca, maintenance free, useful life of 3-5
years.
Charge time 4-6 hours to charge 90% of its capacity.
Can be replaced by
the user Yes.
Capacity (Ah) 4.5 7 9 7 9
Number 1 2
FUNCTIONS
Cold start Yes.
Automatic restart Yes, once the operating time has ended and once
reconnected to the mains.
OPTICAL LED INDICATIONS AND ACOUSTIC ALARMS
Normal operation,
connected to the
mains
Green LED On
Alarm Off
Mains error and UPS
in the battery mode
Green LED flashing.
Beeping sound every
10 sec.
Yellow LED flashing
Beeping sound every
10 sec.
Low battery LED flashes every sec.
Constant beeping.
Yellow LED flashing. Red
LED On
Beeping every sec.
UPS stopped Green LED Off
Alarm Off
UPS fault LED Off.
Continuous beeping.
Red LED On
Constant beeping
MODEL 500 650 850 1100 1500 2000
COMMUNICATION
Port USB HID, according to the model
Software Supports Windows, Linux, Unix and Mac operating
systems.
Download from support.salicru.com
GENERAL
Maximum altitude 2400 m a.s.l.
Relative humidity Up to 90%, non-condensing.
Temperature 0.. 40ºC.
Acoustic noise at
1 m. < 40 dBA.
STANDARDS
Safety EN-IEC 62040-1.
Electromagnetic
compatibility. (EMC) EN-IEC 62040-2.
Quality and
Environmental
Management
ISO 9001 and ISO 14001.
DIMENSIONS AND WEIGHT
Depth (mm) 300 320
Width (mm) 101 130
Height (mm) 142 182
Net weight (kg) 3.50 4.45 4.90 8.20 10.40 11.00
(1) The autonomy and power of the equipment can be affected
depending on the input voltage.
(2) Battery mode.
Tabla 2. General technical specifications.
13
: .............................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
.........................................................................................................................................................................................................................
USER MANUAL SPS.LINK UNINTERRUPTIBLE POWER SUPPLY (UPS) SYSTEMS
www.linkedin.com/company/salicru
@salicru_SA
Avda. de la Serra 100
08460 Palautordera
BARCELONA
Tel. +34 93 848 24 00
Fax +34 93 848 22 05
services@salicru.com
SALICRU.COM
Product Range
Uninterruptible Power Supplies (UPS)
Lighting Flow Dimmer-Stabilisers
DC Power Systems
Static Inverters
Photovoltaic Inverters
Voltage stabilisers
The Technical Service and Support (T.S.S.) network, Com-
mercial network and warranty information are available in
website:
www.salicru.com
REF. EL157B01 REV. B CODE 401*