Table of Contents
- Enterprise Capacity 3.5 HDD
- Seagate® Technology Support Services
- 1.0 Scope
- 2.0 Applicable standards and reference documentation
- 3.0 General description
- 4.0 Performance characteristics
- 5.0 Reliability specifications
- 6.0 Physical/electrical specifications
- 7.0 About FIPS
- 8.0 About self-encrypting drives
- 9.0 Defect and error management
- 10.0 Installation
- 11.0 Interface requirements
Seagate ST3000NM0045 User Manual
Displayed below is the user manual for ST3000NM0045 by Seagate which is a product in the Internal Hard Drives category. This manual has pages.
Related Manuals
Standard
512N models
ST4000NM0025
ST3000NM0025
ST2000NM0045
ST1000NM0045
Self-Encryption
512N models
ST4000NM0065
ST3000NM0035
ST2000NM0085
ST1000NM0075
SED FIPS (140-2)
512N models
ST4000NM0135
ST3000NM0045
Enterprise Capacity
3.5 HDD
v5 SAS Product Manual
100793635, Rev. E
June 2017
© 2017 Seagate Technology LLC. All rights reserved.
Publication number: 100793635, Rev. E June 2017
Seagate, Seagate Technology and the Spiral logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries. Raid Rebuild and SeaTools are either
trademarks or registered trademarks of Seagate Technology LLC or one of its affiliated companies in the United States and/or other countries. The FIPS logo is a certification mark of NIST,
which does not imply product endorsement by NIST, the U.S., or Canadian governments.All other trademarks or registered trademarks are the property of their respective owners.
No part of this publication may be reproduced in any form without written permission of Seagate Technology LLC.
Call 877-PUB-TEK1 (877-782-8351) to request permission.
When referring to drive capacity, one gigabyte, or GB, equals one billion bytes and one terabyte, or TB, equals one trillion bytes. Your computer’s operating system may use a different
standard of measurement and report a lower capacity. In addition, some of the listed capacity is used for formatting and other functions, and thus will not be available for data storage.
Actual quantities will vary based on various factors, including file size, file format, features and application software. Actual data rates may vary depending on operating environment and
other factors. The export or re-export of hardware or software containing encryption may be regulated by the U.S. Department of Commerce, Bureau of Industry and Security (for more
information, visit www.bis.doc.gov), and controlled for import and use outside of the U.S. Seagate reserves the right to change, without notice, product offerings or specifications.
Document Revision History
Revision Date Pages affected and Description of changes
Rev. A 04/25/2016 Initial release.
Rev. B 08/11/2016
8: Updated to Korean RRA
9: Updated to China RoHS 2
29: Revised Non-Op Shock to 250Gs for all capacities
33: Corrected 3TB weight to 680g / 1.500 lb
Rev. C 09/01/2016 8: Added Korean text for Class B device warning
46: Changed Information Exception Log Page 2Fh to “Y”
Rev. D 11/30/2016
8: Updated to MSIP Korean text for Class B device warning
10: Updated Section 2.2 Reference Documents
30: Revised Non-Op shock to 300 Gs @ 2 ms for all capacities
Rev. E 06/01/2017 14: Updated Section 4.1.1 Format command execution time (for 4TB models)
Seagate Enterprise Capacity 3.5 HDD v5 SAS Product Manual, Rev. E 2
Contents
Seagate® Technology Support Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.0 Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.0 Applicable standards and reference documentation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.1 Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.1.1 Electromagnetic compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.1.2 Electromagnetic compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.1.3 European Union Restriction of Hazardous Substances (RoHS) . . . . . . . . . . . . . . . . . . . . . . . . 9
2.1.4 China Requirements — China RoHS 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.2 Reference documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.0 General description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3.1 Standard features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.2 Media description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.3 Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.4 Reliability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3.5 Formatted capacities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3.6 Programmable drive capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3.7 Factory-installed options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.0 Performance characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.1 Internal drive characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.1.1 Format command execution time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.1.2 General performance characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.2 Start/stop time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4.3 Prefetch/multi-segmented cache control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4.4 Cache operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4.4.1 Caching write data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
4.4.2 Prefetch operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.0 Reliability specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5.1 Error rates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5.1.1 Recoverable Errors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5.1.2 Unrecoverable Errors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5.1.3 Seek errors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5.1.4 Interface errors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5.2 Reliability and service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
5.2.1 Annualized Failure Rate (AFR) and Mean Time Between Failure (MTBF) . . . . . . . . . . . . . . 18
5.2.2 Hot plugging the drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
5.2.3 S.M.A.R.T. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5.2.4 Thermal monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
5.2.5 Drive Self Test (DST) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
5.2.6 Product warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Seagate Enterprise Capacity 3.5 HDD v5 SAS Product Manual, Rev. E 3
Contents
6.0 Physical/electrical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
6.1 PowerChoiceTM power management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
6.1.1 PowerChoice reporting methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
6.2 AC power requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
6.3 DC power requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
6.3.1 Conducted noise immunity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
6.3.2 Power sequencing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
6.3.3 Current profiles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
6.4 Power dissipation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
6.5 Environmental limits. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
6.5.1 Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
6.5.2 Humidity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
6.5.3 Effective altitude (sea level) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
6.5.4 Shock and vibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
6.5.5 Acoustics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
6.5.6 Air cleanliness. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
6.5.7 Corrosive environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
6.5.8 Electromagnetic susceptibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
6.6 Mechanical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
7.0 About FIPS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
8.0 About self-encrypting drives. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
8.1 Data encryption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
8.2 Controlled access. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
8.2.1 Admin SP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
8.2.2 Locking SP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
8.2.3 Default password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
8.3 Random number generator (RNG). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
8.4 Drive locking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
8.5 Data bands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
8.6 Cryptographic erase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
8.7 Authenticated firmware download . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
8.8 Power requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
8.9 Supported commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
8.10 Sanitize - CRYPTOGRAPHIC ERASE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
8.11 RevertSP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Seagate Enterprise Capacity 3.5 HDD v5 SAS Product Manual, Rev. E 4
Contents
9.0 Defect and error management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
9.1 Drive internal defects/errors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
9.2 Drive error recovery procedures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
9.3 SAS system errors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
9.4 Background Media Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
9.5 Media Pre-Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
9.6 Deferred Auto-Reallocation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
9.7 Idle Read After Write. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
9.8 Protection Information (PI). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
9.8.1 Levels of PI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
9.8.2 Setting and determining the current Type Level. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
9.8.3 Identifying a Protection Information drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
10.0 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
10.1 Drive orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
10.2 Cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
10.3 Drive mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
10.4 Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
11.0 Interface requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
11.1 SAS features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
11.1.1 task management functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
11.1.2 task management responses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
11.2 Dual port support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
11.3 SCSI commands supported . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
11.3.1 Inquiry data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
11.3.2 Mode Sense data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
11.4 Miscellaneous operating features and conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
11.4.1 SAS physical interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
11.4.2 Physical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
11.4.3 Connector requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
11.4.4 Electrical description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
11.4.5 Pin descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
11.4.6 SAS transmitters and receivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
11.4.7 Power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
11.5 Signal characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
11.5.1 Ready LED Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
11.5.2 Differential signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
11.6 SAS-3 Specification Compliance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
11.7 Additional information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Seagate Enterprise Capacity 3.5 HDD v5 SAS Product Manual, Rev. E 5
For information regarding online support and services, visit: http://www.seagate.com/about/contact-us/technical-support/
For information regarding Warranty Support, visit: http://www.seagate.com/support/warranty-and-replacements/
For information regarding data recovery services, visit: http://www.seagate.com/services-software/data-recovery-services/
For Seagate OEM, Distribution partner portal and reseller portal, visit: http://www.seagate.com/partners
Seagate® Technology Support Services
Seagate Enterprise Capacity 3.5 HDD v5 SAS Product Manual, Rev. E 6
1.0 Scope
This manual describes Seagate® Enterprise Capacity 3.5 HDD v5 SAS (Serial Attached SCSI) disk drives.
Enterprise Capacity 3.5 HDD v5 drives support the SAS Protocol specifications to the extent described in this manual. The SAS Interface Manual (part
number 100293071) describes the general SAS characteristics of this and other Seagate SAS drives. The Self-Encrypting Drive Reference Manual,
part number 100515636, describes the interface, general operation, and security features available on Self-Encrypting Drive models.
Product data communicated in this manual is specific only to the model numbers listed in this manual. The data listed in this manual may not be
predictive of future generation specifications or requirements. If designing a system which will use one of the models listed or future generation
products and need further assistance, please contact the Field Applications Engineer (FAE) or our global support services group as shown in See
“Seagate® Technology Support Services” on page 5.
Unless otherwise stated, the information in this manual applies to standard and Self-Encrypting Drive models.
.
Standard 512N models Self-Encrypting 512N (SED) models SED FIPS (140-2) 512N models
ST4000NM0025 ST4000NM0065 ST4000NM0135
ST3000NM0025 ST3000NM0035 ST3000NM0045
ST2000NM0045 ST2000NM0085
ST1000NM0045 ST1000NM0075
Note Previous generations of Seagate Self-Encrypting Drive models were called Full Disk Encryption (FDE) models
before a differentiation between drive-based encryption and other forms of encryption was necessary.
Note The Self-Encrypting Drive models indicated on the cover of this product manual have provisions for “Security of Data
at Rest” based on the standards defined by the Trusted Computing Group (see www.trustedcomputinggroup.org).
Seagate Enterprise Capacity 3.5 HDD v5 SAS Product Manual, Rev. E 7
2.0 Applicable standards and reference documentation
The drives documented in this manual have been developed as system peripherals to the highest standards of design and construction. The drives
depends on host equipment to provide adequate power and environment for optimum performance and compliance with applicable industry and
governmental regulations. Special attention must be given in the areas of safety, power distribution, shielding, audible noise control, and
temperature regulation. In particular, the drive must be securely mounted to guarantee the specified performance characteristics. Mounting by
bottom holes must meet the requirements of Section 10.3.
2.1 Standards
The Enterprise Capacity 3.5 HDD v5 family complies with Seagate standards as noted in the appropriate sections of this manual and the Seagate SAS
Interface Manual, part number 100293071.
The drives are recognized in accordance with UL 60950-1 as tested by UL, CSA 60950-1 as tested by CSA, and EN60950-1 as tested by TUV.
The security features of Self-Encrypting Drive models are based on the “TCG Storage Architecture Core Specification” and the “TCG Storage
Workgroup Security Subsystem Class: Enterprise_A” specification with additional vendor-unique features as noted in this product manual.
2.1.1 Electromagnetic compatibility
The drive, as delivered, is designed for system integration and installation into a suitable enclosure prior to use. The drive is supplied as a
subassembly and is not subject to Subpart B of Part 15 of the FCC Rules and Regulations nor the Radio Interference Regulations of the Canadian
Department of Communications.
The design characteristics of the drive serve to minimize radiation when installed in an enclosure that provides reasonable shielding. The drive is
capable of meeting the Class B limits of the FCC Rules and Regulations of the Canadian Department of Communications when properly packaged;
however, it is the user’s responsibility to assure that the drive meets the appropriate EMI requirements in their system. Shielded I/O cables may be
required if the enclosure does not provide adequate shielding. If the I/O cables are external to the enclosure, shielded cables should be used, with
the shields grounded to the enclosure and to the host controller.
2.1.1.1 Electromagnetic susceptibility
As a component assembly, the drive is not required to meet any susceptibility performance requirements. It is the responsibility of those integrating
the drive within their systems to perform those tests required and design their system to ensure that equipment operating in the same system as
the drive or external to the system does not adversely affect the performance of the drive. See Table 13, DC power requirements.
Seagate Enterprise Capacity 3.5 HDD v5 SAS Product Manual, Rev. E 8
2.1.2 Electromagnetic compliance
Seagate uses an independent laboratory to confirm compliance with the directives/standards for CE Marking and C-Tick Marking. The drive was
tested in a representative system for typical applications. The selected system represents the most popular characteristics for test platforms. The
system configurations include:
• Typical current use microprocessor
•Keyboard
• Monitor/display
•Printer
•Mouse
Although the test system with this Seagate model complies with the directives/standards, we cannot guarantee that all systems will comply. The
computer manufacturer or system integrator shall confirm EMC compliance and provide the appropriate marking for their product.
Electromagnetic compliance for the European Union
If this model has the CE Marking it complies with the European Union requirements of the Electromagnetic Compatibility Directive 2004/108/EC as
put into place on 20 July 2007.
Canada ICES-003
If this model has the ICES-003 Marking it complies with the Canadian Standard Association Standard CAN/CSA-CISPR 22-10, Information
Technology Equipment - Radio Disturbance Characteristics - Limits and Methods of Measurement.
Australian RCM Compliance Mark
Models displayed with the RCM compliance mark, comply with the mandatory standards as per the Australian Communications and Media
Authority (ACMA) Electromagnetic Compatibility (EMC) regulatory arrangement.
Korean RRA
If these drives have the Korean Communications Commission (KCC) logo, they comply with paragraph 1 of Article 11 of the Electromagnetic
Compatibility control Regulation and meet the Electromagnetic Compatibility (EMC) Framework requirements of the Radio Research Agency (RRA)
Communications Commission, Republic of Korea.
These drives have been tested and comply with the Electromagnetic Interference/Electromagnetic Susceptibility (EMI/EMS) for Class B products.
Drives are tested in a representative, end-user system by a Korean-recognized lab.
Taiwanese BSMI
If this model has two Chinese words meaning “EMC certification” followed by an eight digit identification number, as a Marking, it complies with
Chinese National Standard (CNS) 13438 and meets the Electromagnetic Compatibility (EMC) Framework requirements of the Taiwanese Bureau of
Standards, Metrology, and Inspection (BSMI).
ࣗطیࡈ߇ΰח
%
ɼࢽࡈ؏ܞݦࢢ
ࢇЕɼࢽࡈ% ࢷળࢶଢԻ۰࣯Ի
ɼࢽ߾۰یࡈଜЕʨࡶּࢶࡳԻଜֲ ֻҘ
ࠇ߾۰یࡈଟܹݡТЬ
Seagate Enterprise Capacity 3.5 HDD v5 SAS Product Manual, Rev. E 9
2.1.3 European Union Restriction of Hazardous Substances (RoHS)
The European Union Restriction of Hazardous Substances (RoHS) Directive, restricts the presence of chemical substances, including Lead, Cadmium,
Mercury, Hexavalent Chromium, PBB and PBDE, in electronic products, effective July 2006. This drive is manufactured with components and
materials that comply with the RoHS Directive.
A number of parts and materials in Seagate products are procured from external suppliers. We rely on the representations of our suppliers
regarding the presence of RoHS substances in these parts and materials. Our supplier contracts require compliance with our chemical substance
restrictions, and our suppliers document their compliance with our requirements by providing material content declarations for all parts and
materials for the disk drives documented in this publication. Current supplier declarations include disclosure of the inclusion of any RoHS-regulated
substance in such parts or materials.
Seagate also has internal systems in place to ensure ongoing compliance with the RoHS Directive and all laws and regulations which restrict
chemical content in electronic products. These systems include standard operating procedures that ensure that restricted substances are not
utilized in our manufacturing operations, laboratory analytical validation testing, and an internal auditing process to ensure that all standard
operating procedures are complied with.
2.1.4 China Requirements — China RoHS 2
China RoHS 2 refers to the Ministry of Industry and Information Technology Order No. 32, effective July 1, 2016, titled Management
Methods for the Restriction of the Use of Hazardous Substances in Electrical and Electronic Products. To comply with China RoHS 2,
we determined this product's Environmental Protection Use Period (EPUP) to be 20 years in accordance with the Marking for the
Restricted Use of Hazardous Substances in Electronic and Electrical Products, SJT 11364-2014.
中国电器电子产品有害物质限制使用管理办法
(Management Methods for the Restriction of the Use of Hazardous Substances in Electrical and Electronic
Products _ China RoHS)
产品中有害物质的名称及含量
(Name and Content of the Hazardous Substances in Product)
Table 12 Hazardous Substances
部件名称
Part Name
有害物质
Hazardous Substances
铅
Lead
(Pb)
汞
Mercury
(Hg)
镉
Cadmium
(Cd)
六价铬
Hexavalent Chromium
(CF (VI))
多溴联苯
Polybrominated
biphenyls (PBB)
多溴二苯醚
Polybrominated
diphenyl ethers (PBDE)
印刷电路板组装
PCBA XO O O O O
机壳
Chassis XO O O O O
本表格依据 SJ/T 11364 的规定编制。
This table is prepared in accordance with the provisions of SJ/T 11364-2014
O：表示该有害物质在该部件所有均质材料中的含量均在 GB/T 26572 规定的限量要求以下。
O: Indicates that the hazardous substance contained in all of the homogeneous materials for this part is below the limit
requirement of GB/T26572.
X：表示该有害物质至少在该部件的某一均质材料中的含量超出 GB/T 26572 规定的限量要求。
X: Indicates that the hazardous substance contained in at least one of the homogeneous materials used for this part is above the
limit requirement of GB/T26572.
20
Seagate Enterprise Capacity 3.5 HDD v5 SAS Product Manual, Rev. E 10
2.2 Reference documents
SAS Interface Manual
Seagate part number: 100293071
SCSI Commands Reference Manual
Seagate part number: 100293068
Self-Encrypting Drives Reference Manual
Seagate part number: 100515636
ANSI SAS Documents
SFF-8223 2.5” Drive Form Factor with Serial Connector
SFF-8460 HSS Backplane Design Guidelines
SFF-8470 Multi Lane Copper Connector
SFF-8482 SAS Plug Connector
INCITS 538 SCSI Protocol Layer-4 (SPL-4) Rev. 08
INCITS 534 Serial Attached SCSI (SAS-4)
INCITS 506 SCSI Block Commands-4 (SBC-4) Rev. 10
INCITS 502 SCSI Primary Commands-5 (SPC-5) Rev. 10
ANSI Small Computer System Interface (SCSI) Documents
INCITS 515 SCSI Architecture Model (SAM-5) Rev. 11
Trusted Computing Group (TCG) Documents (apply to Self-Encrypting Drive models only)
TCG Storage Architecture Core Specification, v1.00
TCG Storage Security Subsystem Class Enterprise Specification, v1.01
Specification for Acoustic Test Requirement and Procedures
Seagate part number: 30553-001
In case of conflict between this document and any referenced document, this document takes precedence.
Seagate Enterprise Capacity 3.5 HDD v5 SAS Product Manual, Rev. E 11
3.0 General description
Enterprise Capacity 3.5 HDD v5 drives provide high performance, high capacity data storage for a variety of systems including engineering
workstations, network servers, mainframes, and supercomputers. The Serial Attached SCSI interface is designed to meet next-generation
computing demands for performance, scalability, flexibility and high-density storage requirements.
Enterprise Capacity 3.5 HDD v5 drives are random access storage devices designed to support the Serial Attached SCSI Protocol as described in the
ANSI specifications, this document, and the SAS Interface Manual (part number 100293071) which describes the general interface characteristics of
this drive. Enterprise Capacity 3.5 HDD v5 drives are classified as intelligent peripherals and provide level 2 conformance (highest level) with the
ANSI SCSI-1 standard. The SAS connectors, cables and electrical interface are compatible with Serial ATA (SATA), giving future users the choice of
populating their systems with either SAS or SATA hard disk drives. This allows users to continue to leverage existing investment in SCSI while
gaining a 12Gb/s serial data transfer rate.
The Self-Encrypting Drive models indicated on the cover of this product manual have provisions for “Security of Data at Rest” based on the
standards defined by the Trusted Computing Group
(see www.trustedcomputinggroup.org).
The head and disk assembly (HDA) is sealed at the factory. Air recirculates within the HDA through a non-replaceable filter to maintain a
contamination-free HDA environment.
Enterprise Capacity 3.5 HDD v5 drives use a dedicated load/unload zone at the outermost radius of the media to eliminate the possibility of
destroying or degrading data by landing in the data zone. The heads automatically go to the ramp load/unload when power is removed from the
drive.
An automatic shipping lock prevents potential damage to the heads and discs that results from movement during shipping and handling. The
shipping lock disengages and the head load process begins when power is applied to the drive.
Enterprise Capacity 3.5 HDD v5 drives decode track 0 location data from the servo data embedded on each surface to eliminate mechanical
transducer adjustments and related reliability concerns.
The drives also use a high-performance actuator assembly with a low-inertia, balanced, patented, straight arm design that provides excellent
performance with minimal power dissipation.
Note Never disassemble the HDA and do not attempt to service items in the sealed enclosure (heads, media, actuator, etc.) as this requires
special facilities. The drive does not contain user-replaceable parts. Opening the HDA for any reason voids the product warranty.
Note Seagate recommends validating the configuration with the selected HBA/
RAID controller manufacturer to ensure use of full capacity is supported.
Seagate Enterprise Capacity 3.5 HDD v5 SAS Product Manual, Rev. E 12
3.1 Standard features
Enterprise Capacity 3.5 HDD v5 drives have the following standard features:
• 3.0 / 6.0/12.0 Gb Serial Attached SCSI (SAS) interface
• 128 - deep task set (queue)
• 128 MB data buffer (see Section 4.4).
• Dedicated head load/unload zone
• Drive Self Test (DST)
• Embedded servo design
• Firmware downloadable using the SAS interface
• Flawed logical block reallocation at format time
• Idle Read After Write (IRAW)
• Industry standard SFF 3.5-in dimensions
• Integrated dual port SAS controller supporting the SCSI protocol
• Jumperless configuration.
• No preventive maintenance or adjustments required
• Perpendicular recording technology
•Power Save
• Programmable auto write and read reallocation
• Programmable logical block reallocation scheme
• Reallocation of defects on command (Post Format)
• SAS Power Disable
•Seagate RAID Rebuild
TM
• Self diagnostics performed when power is applied to the drive
• Support for SAS expanders and fanout adapters
• Supports up to 32 initiators
• Tarnish-resistant components to help protect drive from environmental elements, increasing field reliability
• User-selectable logical block sizes for 5xxN (512, 520, 524 or 528 bytes per logical block).
• Vertical, horizontal, or top down mounting
Seagate Enterprise Capacity 3.5 HDD v5 SAS Self-Encrypting Drive models have the following additional features:
• 16 independent data bands
• Authenticated firmware download
• Automatic data encryption/decryption
• Controlled access
• Cryptographic erase of user data for a drive that will be repurposed or scrapped
•Drive locking
• Random number generator
3.2 Media description
The media used on the drive has a aluminum substrate coated with a thin film magnetic material, overcoated with a proprietary protective layer for
improved durability and environmental protection.
3.3 Performance
• 1200MB/s maximum instantaneous data transfers.
• 7200 RPM spindle. Average latency = 4.16ms
• Adaptive seek velocity; improved seek performance
• Background processing of queue
• Programmable multi-segmentable cache buffer
• Supports start and stop commands (spindle stops spinning)
.
Note There is no significant performance difference between Self-
Encrypting Drive and standard (non-Self-Encrypting Drive) models.
Seagate Enterprise Capacity 3.5 HDD v5 SAS Product Manual, Rev. E 13
3.4 Reliability
• 5-year warranty
• Annualized Failure Rate (AFR) of 0.44%
• Balanced low mass rotary voice coil actuator
• Incorporates industry-standard Self-Monitoring Analysis and Reporting Technology (S.M.A.R.T.)
• Mean time between failures (MTBF) of 2,000,000 hours
3.5 Formatted capacities
Standard OEM models are formatted to 512 bytes per block. The block size is selectable at format time and must be a multiple of 4 bytes. Users
having the necessary equipment may modify the data block size before issuing a format command and obtain different formatted capacities than
those listed.
To provide a stable target capacity environment and at the same time provide users with flexibility if they choose, Seagate recommends product
planning in one of two modes:
1. Seagate designs specify capacity points at certain block sizes that Seagate guarantees current and future products will meet. We recommend
customers use this capacity in their project planning, as it ensures a stable operating point with backward and forward compatibility from gen-
eration to generation. The current guaranteed operating points for this product are
3.6 Programmable drive capacity
Using the Mode Select command, the drive can change its capacity to something less than maximum. See the Mode Select (6) parameter list table
in the SAS Interface Manual, part number 100293071. A value of zero in the Number of Blocks field indicates that the drive will not change the
capacity it is currently formatted to have. A number other than zero and less than the maximum number of LBAs in the Number of Blocks field
changes the total drive capacity to the value in the Number of Blocks field. A value greater than the maximum number of LBAs is rounded down to
the maximum capacity.
3.7 Factory-installed options
Users may order the following items which are incorporated at the manufacturing facility during production or packaged before shipping. Some of
the options available are (not an exhaustive list of possible options):
• Other capacities can be ordered depending on sparing scheme and sector size requested.
• Single-unit shipping pack. The drive is normally shipped in bulk packaging to provide maximum protection against transit damage. Units
shipped individually require additional protection as provided by the single unit shipping pack. Users planning single unit distribution should
specify this option.
•The Safety and Regulatory Agency Specifications, part number 75789512, is usually included with each standard OEM drive shipped, but extra cop-
ies may be ordered.
Sector
Size
4TB models 3TB models 2TB models 1TB models
Decimal Hex Decimal Hex Decimal Hex Decimal Hex
512 7,814,037,168 1D1C0BEB0 5,860,533,168 15D50A3B0 3,907,029,168 E8E088B0 1,953,525,168 74706DB0
520 7,648,717,976 1C7E62C98 5,736,538,480 155ECA170 3,824,358,992 E3F31650 1,923,076,936 729FD348
528 7,438,330,376 1BB5BEA08 5,578,747,784 14C84EF88 3,719,165,192 DDADF508 1,876,331,336 6FD68B48
Seagate Enterprise Capacity 3.5 HDD v5 SAS Product Manual, Rev. E 14
4.0 Performance characteristics
This section provides detailed information concerning performance-related characteristics and features of Enterprise Capacity 3.5 HDD v5 drives.
4.1 Internal drive characteristics
Drive capacity 4TB models 3TB models 2TB models 1TB models (formatted, rounded off value)
Read/write data heads 7 7 4 2
Bytes/track 1,470,464 Bytes (average, rounded off values)
Bytes/surface 500,000 MB (unformatted, rounded off values)
Tracks/surface (total) 337,400 Tracks (user accessible)
Tracks/in 369,000 TPI (average)
Peak bits/in 2,018,000 BPI
Areal density 733 Gb/in2
Internal data rate 2432 Mb/s (max)
Disk rotation speed 7200 RPM
Avg rotational latency 4.16 ms
4.1.1 Format command execution time
Execution time measured from receipt of the last byte of the Command Descriptor Block (CDB) to the request for a Status Byte Transfer to the
Initiator (excluding connect/disconnect).
When changing sector sizes, the format times shown above may need to be increased by 30 minutes.
4.1.2 General performance characteristics
521N-byte sectors (minutes) 4TB models 3TB models 2TB models 1TB models
Maximum (with verify) 814 605 393 203
Maximum (without verify) 380 305 197 102
Minimum sector interleave 1 to 1
Maximum Internal data rate* 2.32 Gb/s
Sustained transfer rate 100 to 216 MiB/s **
SAS Interface maximum instantaneous transfer rate 1200MB/s* per port
(dual port = 2400MB/s*)
Logical block sizes
512 (default), 520, 524 or 528.
Read/write consecutive sectors on a track Yes
Flaw reallocation performance impact (for flaws reallocated at format time using the spare
sectors per sparing zone reallocation scheme.)
Negligible
Average rotational latency 4.16ms
*Assumes no errors and no relocated logical blocks. Rate measured from the start of the first logical block transfer to or from the
host.
** MiB/s x 1.048 = MB/s
Seagate Enterprise Capacity 3.5 HDD v5 SAS Product Manual, Rev. E 15
4.2 Start/stop time
The drive accepts the commands listed in the SAS Interface Manual less than 3 seconds after DC power has been applied.
If the drive receives a NOTIFY (ENABLE SPINUP) primitive through either port and has not received a START STOP UNIT command with the START bit
equal to 0, the drive becomes ready for normal operations within 30 seconds (excluding the error recovery procedure).
If the drive receives a START STOP UNIT command with the START bit equal to 0 before receiving a NOTIFY (ENABLE SPINUP) primitive, the drive
waits for a START STOP UNIT command with the START bit equal to 1. After receiving a START STOP UNIT command with the START bit equal to 1, the
drive waits for a NOTIFY (ENABLE SPINUP) primitive. After receiving a NOTIFY (ENABLE SPINUP) primitive through either port, the drive becomes
ready for normal operations within 30 seconds (excluding the error recovery procedure).
If the drive receives a START STOP UNIT command with the START bit and IMMED bit equal to 1 and does not receive a NOTIFY (ENABLE SPINUP)
primitive within 5 seconds, the drive fails the START STOP UNIT command.
The START STOP UNIT command may be used to command the drive to stop the spindle. Stop time is 23 seconds (maximum) from removal of DC
power. SCSI stop time is 23 seconds. There is no power control switch on the drive.
4.3 Prefetch/multi-segmented cache control
The drive provides a prefetch (read look-ahead) and multi-segmented cache control algorithms that in many cases can enhance system
performance. Cache refers to the drive buffer storage space when it is used in cache operations. To select this feature, the host sends the Mode
Select command with the proper values in the applicable bytes in page 08h. Prefetch and cache operations are independent features from the
standpoint that each is enabled and disabled independently using the Mode Select command; however, in actual operation, the prefetch feature
overlaps cache operation somewhat as described in sections 4.4.1 and 4.4.2.
All default cache and prefetch mode parameter values (Mode Page 08h) for standard OEM versions of this drive family are given in Table 20.
4.4 Cache operation
.
Of the 128MB physical buffer space in the drive, approximately (60,000) KB can be used as a cache. The buffer is divided into logical segments from
which data is read and to which data is written.
The drive keeps track of the logical block addresses of the data stored in each segment of the buffer. If the cache is enabled (see RCD bit in the SAS
Interface Manual ), data requested by the host with a read command is retrieved from the buffer, if possible, before any disk access is initiated. If
cache operation is not enabled, the buffer is still used, but only as circular buffer segments during disk medium read operations (disregarding
Prefetch operation for the moment). That is, the drive does not check in the buffer segments for the requested read data, but goes directly to the
medium to retrieve it. The retrieved data merely passes through some buffer segment on the way to the host. All data transfers to the host are in
accordance with buffer-full ratio rules. See the explanation provided with the information about Mode Page 02h (disconnect/reconnect control) in
the SAS Interface Manual.
The following is a simplified description of the prefetch/cache operation:
Case A—read command is received and all of the requested logical blocks are already in the cache:
1. Drive transfers the requested logical blocks to the initiator.
Case B—A Read command requests data, and at least one requested logical block is not in any segment of the cache:
1. The drive fetches the requested logical blocks from the disk and transfers them into a segment, and then from there to the host in accordance
with the Mode Select Disconnect/Reconnect parameters, page 02h.
2. If the prefetch feature is enabled, refer to section 4.4.2 for operation from this point.
Each cache segment is actually a self-contained circular buffer whose length is an integer number of logical blocks. The drive dynamically creates
and removes segments based on the workload. The wrap-around capability of the individual segments greatly enhances the cache’s overall
performance.
The size of each segment is not reported by Mode Sense command page 08h, bytes 14 and 15. The value 0XFFFF is always reported regardless of
the actual size of the segment. Sending a size specification using the Mode Select command (bytes 14 and 15) does not set up a new segment size.
If the STRICT bit in Mode page 00h (byte 2, bit 1) is set to one, the drive responds as it does for any attempt to change an unchangeable parameter.
Note Refer to the SAS Interface Manual for more detail concerning the cache bits.
Seagate Enterprise Capacity 3.5 HDD v5 SAS Product Manual, Rev. E 16
4.4.1 Caching write data
Write caching is a write operation by the drive that makes use of a drive buffer storage area where the data to be written to the medium is stored
while the drive performs the Write command.
If read caching is enabled (RCD=0), then data written to the medium is retained in the cache to be made available for future read cache hits. The
same buffer space and segmentation is used as set up for read functions. The buffer segmentation scheme is set up or changed independently,
having nothing to do with the state of RCD. When a write command is issued, if RCD=0, the cache is first checked to see if any logical blocks that are
to be written are already stored in the cache from a previous read or write command. If there are, the respective cache segments are cleared. The
new data is cached for subsequent Read commands.
If the number of write data logical blocks exceed the size of the segment being written into, when the end of the segment is reached, the data is
written into the beginning of the same cache segment, overwriting the data that was written there at the beginning of the operation; however, the
drive does not overwrite data that has not yet been written to the medium.
If write caching is enabled (WCE=1), then the drive may return Good status on a write command after the data has been transferred into the cache,
but before the data has been written to the medium. If an error occurs while writing the data to the medium, and Good status has already been
returned, a deferred error will be generated.
The Synchronize Cache command may be used to force the drive to write all cached write data to the medium. Upon completion of a Synchronize
Cache command, all data received from previous write commands will have been written to the medium. Table 20 shows the mode default settings
for the drive.
4.4.2 Prefetch operation
If the Prefetch feature is enabled, data in contiguous logical blocks on the disk immediately beyond that which was requested by a Read command
are retrieved and stored in the buffer for immediate transfer from the buffer to the host on subsequent Read commands that request those logical
blocks (this is true even if cache operation is disabled). Though the prefetch operation uses the buffer as a cache, finding the requested data in the
buffer is a prefetch hit, not a cache operation hit.
To enable Prefetch, use Mode Select page 08h, byte 12, bit 5 (Disable Read Ahead - DRA bit). DRA bit = 0 enables prefetch.
The drive does not use the Max Prefetch field (bytes 8 and 9) or the Prefetch Ceiling field (bytes 10 and 11).
When prefetch (read look-ahead) is enabled (enabled by DRA = 0), the drive enables prefetch of contiguous blocks from the disk when it senses that
a prefetch hit will likely occur. The drive disables prefetch when it decides that a prefetch hit is not likely to occur.
Seagate Enterprise Capacity 3.5 HDD v5 SAS Product Manual, Rev. E 17
5.0 Reliability specifications
The following reliability specifications assume correct host and drive operational interface, including all interface timings, power supply voltages,
environmental requirements and drive mounting constraints.
5.1 Error rates
The error rates stated in this manual assume the following:
• The drive is operated in accordance with this manual using DC power as defined in paragraph 6.3, "DC power requirements."
• Errors caused by host system failures are excluded from error rate computations.
•Assume random data.
• Default OEM error recovery settings are applied. This includes AWRE, ARRE, full read retries, full write retries and full retry time.
5.1.1 Recoverable Errors
Recoverable errors are those detected and corrected by the drive, and do not require user intervention.
Recoverable Data errors will use correction, although ECC on-the-fly is not considered for purposes of recovered error specifications.
Recovered Data error rate is determined using read bits transferred for recoverable errors occurring during a read, and using write bits transferred
for recoverable errors occurring during a write.
5.1.2 Unrecoverable Errors
An unrecoverable data error is defined as a failure of the drive to recover data from the media. These errors occur due to head/media or write
problems. Unrecoverable data errors are only detected during read operations, but not caused by the read. If an unrecoverable data error is
detected, a MEDIUM ERROR (03h) in the Sense Key will be reported. Multiple unrecoverable data errors resulting from the same cause are treated as
1 error.
5.1.3 Seek errors
A seek error is defined as a failure of the drive to position the heads to the addressed track. After detecting an initial seek error, the drive
automatically performs an error recovery process. If the error recovery process fails, a seek positioning error (Error code = 15h or 02h) will be
reported with a Hardware error (04h) in the Sense Key. Recoverable seek errors are specified at Less than 10 errors in 108 seeks. Unrecoverable seek
errors (Sense Key = 04h) are classified as drive failures.
5.1.4 Interface errors
An interface error is defined as a failure of the receiver on a port to recover the data as transmitted by the device port connected to the receiver. The
error may be detected as a running disparity error, illegal code, loss of word sync, or CRC error.
Seek error rate: Less than 10 errors in 108 seeks
Read Error Rates1
1. Error rate specified with automatic retries and data correction with ECC enabled and all flaws reallocated.
Recovered Data Less than 10 errors in 1012 bits transferred (OEM default settings)
Unrecovered Data Less than 1 sector in 1015 bits transferred
Miscorrected Data Less than 1 sector in 1021 bits transferred
Interface error rate: Less than 1 error in 1012 bits transferred
Mean Time Between Failure (MTBF): 2,000,000 hours
Annualized Failure Rate (AFR): 0.44%
Preventive maintenance: None required
Seagate Enterprise Capacity 3.5 HDD v5 SAS Product Manual, Rev. E 18
5.2 Reliability and service
Users can enhance the reliability of Enterprise Capacity 3.5 HDD v5 disk drives by ensuring that the drive receives adequate cooling. Section 6.0
provides temperature measurements and other information that may be used to enhance the service life of the drive. Section 10.2 provides
recommended air-flow information.
5.2.1 Annualized Failure Rate (AFR) and Mean Time Between Failure (MTBF)
The production disk drive shall achieve an annualized failure-rate of 0.44% (MTBF of 2,000,000 hours) over a 5 year service life when used in
Enterprise Storage field conditions as limited by the following:
• 8760 power-on hours per year.
• HDA temperature as reported by the drive <= 40°C
• Ambient wet bulb temp <= 26°C
• Typical workload
• The AFR (MTBF) is a population statistic not relevant to individual units
• ANSI/ISA S71.04-2013 G2 classification levels and dust contamination to ISO 14644-1 Class 8 standards (as measured at the device)
The MTBF specification for the drive assumes the operating environment is designed to maintain nominal drive temperature and humidity.
Occasional excursions in operating conditions between the rated MTBF conditions and the maximum drive operating conditions may occur
without significant impact to the rated MTBF. However continual or sustained operation beyond the rated MTBF conditions will degrade the drive
MTBF and reduce product reliability.
5.2.2 Hot plugging the drive
When a disk is powered on by switching the power or hot plugged, the drive runs a self test before attempting to communicate on its’ interfaces.
When the self test completes successfully, the drive initiates a Link Reset starting with OOB. An attached device should respond to the link reset. If
the link reset attempt fails, or any time the drive looses sync, the drive initiated link reset. The drive will initiate link reset once per second but
alternates between port A and B. Therefore each port will attempt a link reset once per 2 seconds assuming both ports are out of sync.
If the self-test fails, the drive does not respond to link reset on the failing port.
It is the responsibility of the systems integrator to assure that no temperature, energy, voltage hazard, or ESD potential hazard is presented during
the hot connect/disconnect operation. Discharge the static electricity from the drive carrier prior to inserting it into the system.
Nonrecoverable read errors 1 per 1015 bits read, max
Load unload cycles 600,000 cycles
Maximum Rated Workload Maximum rate of <550TB/year
Workloads exceeding the annualized rate may degrade the drive MTBF and impact product
reliability. The Annualized Workload Rate is in units of TB per year, or TB per 8760 power on
hours. Workload Rate = TB transferred * (8760 / recorded power on hours).
Warranty To determine the warranty for a specific drive, use a web browser to access the following web
page: http://www.seagate.com/support/warranty-and-replacements/.
From this page, click on the “Is my Drive under Warranty” link. The following are required to be
provided: the drive serial number, model number (or part number) and country of purchase.
The system will display the warranty information for the drive.
Preventive maintenance None required.
Caution The drive motor must come to a complete stop prior to changing the
plane of operation. This time is required to insure data integrity.
Seagate Enterprise Capacity 3.5 HDD v5 SAS Product Manual, Rev. E 19
5.2.3 S.M.A.R.T.
S.M.A.R.T. is an acronym for Self-Monitoring Analysis and Reporting Technology. This technology is intended to recognize conditions that indicate
imminent drive failure and is designed to provide sufficient warning of a failure to allow users to back up the data before an actual failure occurs.
.
Each monitored attribute has been selected to monitor a specific set of failure conditions in the operating performance of the drive and the
thresholds are optimized to minimize “false” and “failed” predictions.
Controlling S.M.A.R.T.
The operating mode of S.M.A.R.T. is controlled by the DEXCPT and PERF bits on the Informational Exceptions Control mode page (1Ch). Use the
DEXCPT bit to enable or disable the S.M.A.R.T. feature. Setting the DEXCPT bit disables all S.M.A.R.T. functions. When enabled, S.M.A.R.T. collects on-
line data as the drive performs normal read and write operations. When the PERF bit is set, the drive is considered to be in “On-line Mode Only” and
will not perform off-line functions.
Users can measure off-line attributes and force the drive to save the data by using the Rezero Unit command. Forcing S.M.A.R.T. resets the timer so
that the next scheduled interrupt is in one hour.
Users can interrogate the drive through the host to determine the time remaining before the next scheduled measurement and data logging
process occurs. To accomplish this, issue a Log Sense command to log page 0x3E. This allows the user to control when S.M.A.R.T. interruptions occur.
Forcing S.M.A.R.T. with the RTZ command resets the timer.
Performance impact
S.M.A.R.T. attribute data is saved to the disk so that the events that caused a predictive failure can be recreated. The drive measures and saves
parameters once every one hour subject to an idle period on the drive interfaces. The process of measuring off-line attribute data and saving data
to the disk is interruptable. The maximum on-line only processing delay is summarized below:
Reporting control
Reporting is controlled by the MRIE bits in the Informational Exceptions Control mode page (1Ch). An example, if the MRIE is set to one, the
firmware will issue to the host an 01-5D00 sense code. The FRU field contains the type of predictive failure that occurred. The error code is preserved
through bus resets and power cycles.
Determining rate
S.M.A.R.T. monitors the rate at which errors occur and signals a predictive failure if the rate of degraded errors increases to an unacceptable level. To
determine rate, error events are logged and compared to the number of total operations for a given attribute. The interval defines the number of
operations over which to measure the rate. The counter that keeps track of the current number of operations is referred to as the Interval Counter.
S.M.A.R.T. measures error rates. All errors for each monitored attribute are recorded. A counter keeps track of the number of errors for the current
interval. This counter is referred to as the Failure Counter.
Error rate is the number of errors per operation. The algorithm that S.M.A.R.T. uses to record rates of error is to set thresholds for the number of
errors and their interval. If the number of errors exceeds the threshold before the interval expires, the error rate is considered to be unacceptable. If
the number of errors does not exceed the threshold before the interval expires, the error rate is considered to be acceptable. In either case, the
interval and failure counters are reset and the process starts over.
Predictive failures
S.M.A.R.T. signals predictive failures when the drive is performing unacceptably for a period of time. The firmware keeps a running count of the
number of times the error rate for each attribute is unacceptable. To accomplish this, a counter is incremented each time the error rate is
unacceptable and decremented (not to exceed zero) whenever the error rate is acceptable. If the counter continually increments such that it
reaches the predictive threshold, a predictive failure is signaled. This counter is referred to as the Failure History Counter. There is a separate Failure
History Counter for each attribute.
Note The drive’s firmware monitors specific attributes for degradation
over time but can’t predict instantaneous drive failures.
Maximum processing delay
Fully-enabled delay DEXCPT = 0
S.M.A.R.T. delay times 75 ms
Seagate Enterprise Capacity 3.5 HDD v5 SAS Product Manual, Rev. E 20
5.2.4 Thermal monitor
Enterprise Capacity 3.5 HDD v5 drives implement a temperature warning system which:
1. Signals the host if the temperature exceeds a value which would threaten the drive.
2. Saves a S.M.A.R.T. data frame on the drive which exceeds the threatening temperature value.
A temperature sensor monitors the drive temperature and issues a warning over the interface when the temperature exceeds a set threshold. The
temperature is measured at power-up and then at ten-minute intervals after power-up.
The thermal monitor system generates a warning code of 01-0B01 when the temperature exceeds the specified limit in compliance with the SCSI
standard.
This feature is controlled by the Enable Warning (EWasc) bit, and the reporting mechanism is controlled by the Method of Reporting Informational
Exceptions field (MRIE) on the Informational Exceptions Control (IEC) mode page (1Ch).
5.2.5 Drive Self Test (DST)
Drive Self Test (DST) is a technology designed to recognize drive fault conditions that qualify the drive as a failed unit. DST validates the
functionality of the drive at a system level.
There are two test coverage options implemented in DST:
1. Extended test
2. Short test
The most thorough option is the extended test that performs various tests on the drive and scans every logical block address (LBA) of the drive. The
short test is time-restricted and limited in length—it does not scan the entire media surface, but does some fundamental tests and scans portions
of the media.
If DST encounters an error during either of these tests, it reports a fault condition. If the drive fails the test, remove it from service and return it to
Seagate for service.
5.2.5.1 DST failure definition
The drive will present a “diagnostic failed” condition through the self-tests results value of the diagnostic log page if a functional failure is
encountered during DST. The channel and servo parameters are not modified to test the drive more stringently, and the number of retries are not
reduced. All retries and recovery processes are enabled during the test. If data is recoverable, no failure condition will be reported regardless of the
number of retries required to recover the data.
The following conditions are considered DST failure conditions:
• Seek error after retries are exhausted
• Track-follow error after retries are exhausted
• Read error after retries are exhausted
• Write error after retries are exhausted
Recovered errors will not be reported as diagnostic failures.
Seagate Enterprise Capacity 3.5 HDD v5 SAS Product Manual, Rev. E 21
5.2.5.2 Implementation
This section provides all of the information necessary to implement the DST function on this drive.
5.2.5.2.1 State of the drive prior to testing
The drive must be in a ready state before issuing the Send Diagnostic command. There are multiple reasons why a drive may not be ready, some of
which are valid conditions, and not errors. For example, a drive may be in process of doing a format, or another DST. It is the responsibility of the
host application to determine the “not ready” cause.
While not technically part of DST, a Not Ready condition also qualifies the drive to be returned to Seagate as a failed drive.
A Drive Not Ready condition is reported by the drive under the following conditions:
• Motor will not spin
• Motor will not lock to speed
• Servo will not lock on track
• Drive cannot read configuration tables from the disk
In these conditions, the drive responds to a Test Unit Ready command with an 02/04/00 or 02/04/03 code.
5.2.5.2.2 Invoking DST
To invoke DST, submit the Send Diagnostic command with the appropriate Function Code (001b for the short test or 010b for the extended test) in
bytes 1, bits 5, 6, and 7.
5.2.5.2.3 Short and extended tests
DST has two testing options:
1. short
2. extended
These testing options are described in the following two subsections.
Each test consists of three segments: an electrical test segment, a servo test segment, and a read/verify scan segment.
Short test (Function Code: 001b)
The purpose of the short test is to provide a time-limited test that tests as much of the drive as possible within 120 seconds. The short test does not
scan the entire media surface, but does some fundamental tests and scans portions of the media. A complete read/verify scan is not performed and
only factual failures will report a fault condition. This option provides a quick confidence test of the drive.
Extended test (Function Code: 010b)
The objective of the extended test option is to empirically test critical drive components. For example, the seek tests and on-track operations test
the positioning mechanism. The read operation tests the read head element and the media surface. The write element is tested through read/write/
read operations. The integrity of the media is checked through a read/verify scan of the media. Motor functionality is tested by default as a part of
these tests.
The anticipated length of the Extended test is reported through the Control Mode page.
Seagate Enterprise Capacity 3.5 HDD v5 SAS Product Manual, Rev. E 22
5.2.5.2.4 Log page entries
When the drive begins DST, it creates a new entry in the Self-test Results Log page. The new entry is created by inserting a new self-test parameter
block at the beginning of the self-test results log parameter section of the log page. Existing data will be moved to make room for the new
parameter block. The drive reports 20 parameter blocks in the log page. If there are more than 20 parameter blocks, the least recent parameter
block will be deleted. The new parameter block will be initialized as follows:
1. The Function Code field is set to the same value as sent in the DST command
2. The Self-Test Results Value field is set to Fh
3. The drive will store the log page to non-volatile memory
After a self-test is complete or has been aborted, the drive updates the Self-Test Results Value field in its Self-Test Results Log page in non-volatile
memory. The host may use Log Sense to read the results from up to the last 20 self-tests performed by the drive. The self-test results value is a 4-bit
field that reports the results of the test. If the field is set to zero, the drive passed with no errors detected by the DST. If the field is not set to zero, the
test failed for the reason reported in the field.
The drive will report the failure condition and LBA (if applicable) in the Self-test Results Log parameter. The Sense key, ASC, ASCQ, and FRU are used
to report the failure condition.
5.2.5.2.5 Abort
There are several ways to abort a diagnostic. Users can use a SCSI Bus Reset or a Bus Device Reset message to abort the diagnostic.
Users can abort a DST executing in background mode by using the abort code in the DST Function Code field. This will cause a 01 (self-test aborted
by the application client) code to appear in the self-test results values log. All other abort mechanisms will be reported as a 02 (self-test routine was
interrupted by a reset condition).
5.2.6 Product warranty
See “Seagate® Technology Support Services” on page 5 for warranty contact information.
Shipping
When transporting or shipping a drive, use only a Seagate-approved container. Keep the original box. Seagate approved containers are easily
identified by the Seagate Approved Package label. Shipping a drive in a non-approved container voids the drive warranty.
Seagate repair centers may refuse receipt of components improperly packaged or obviously damaged in transit. Contact the authorized Seagate
distributor to purchase additional boxes. Seagate recommends shipping by an air-ride carrier experienced in handling computer equipment.
Storage
Maximum storage periods are 180 days within original unopened Seagate shipping package or 60 days unpackaged within the defined non-
operating limits (refer to environmental section in this manual). Storage can be extended to 1 year packaged or unpackaged under optimal
environmental conditions (25°C, <40% relative humidity non-condensing, and non-corrosive environment). During any storage period the drive
non-operational temperature, humidity, wet bulb, atmospheric conditions, shock, vibration, magnetic and electrical field specifications should be
followed.
Product repair and return information
Seagate customer service centers are the only facilities authorized to service Seagate drives. Seagate does not sanction any third-party repair
facilities. Any unauthorized repair or tampering with the factory seal voids the warranty.
Seagate Enterprise Capacity 3.5 HDD v5 SAS Product Manual, Rev. E 23
6.0 Physical/electrical specifications
This section provides information relating to the physical and electrical characteristics of the drive.
6.1 PowerChoiceTM power management
Drives using the load/unload architecture provide programmable power management to tailor systems for performance and greater energy
efficiency.
The table below lists the supported PowerChoice modes. The further down the user goes in the table, the more power savings the user gets. For
example, Idle_B mode results in greater power savings than Idle_A mode. Standby_Z mode results in the greatest power savings.
PowerChoice modes
PowerChoiceTM can be invoked using one of these two methods:
• Power Condition mode page method—Enable and initialize the idle condition timers and/or the standby condition timers. The timer values are
based on the values set in the Power Condition mode page.
• START STOP UNIT command method—Use the START STOP UNIT command (OPERATION CODE 1Bh). This allows the host to directly transition the
drive to any supported PowerChoice mode.
If both the Power Condition mode page and START STOP UNIT command methods are used, the START STOP UNIT command request takes
precedence over the Power Condition mode page power control and may disable the idle condition and standby condition timers. The REQUEST
SENSE command reports the current PowerChoice state if active and also the method by which the drive entered the PowerChoice state.
When the drive receives a command, all power condition timers are suspended if they were enabled via the Power Condition mode page. Once all
outstanding commands are processed, the power condition timers are reinitialized to the values defined in the Power Condition mode page
6.1.1 PowerChoice reporting methods
PowerChoiceTM provides these reporting methods for tracking purposes:
Request Sense command reports
• Current power condition
• Method of entry
.
Mode Sense command reports (mode page 0x1A)
• Idle conditions enabled / disabled
• Idle condition timer values (100ms increments) (default, saved, current, changeable)
Power Condition Vital Product Data (VPD) Page (VPD page 0x8A)
• Supported power conditions
• Typical recovery time from power conditions (1ms increments)
Start/Stop Cycle Counter Log Page reports (log page 0x0E)
• Specified and accumulated Start/Stops and Load/Unload cycles
Power Condition Transitions Log Page reports (log page 0x1A, subpage 0x00)
• Accumulated transitions to Active, Idle_A, Idle_B, Idle_C, Standby_Y, Standby_Z
Mode Description
Idle_A Reduced electronics
Idle_B Heads unloaded. Disks spinning at full RPM
Idle_C Heads unloaded. Disks spinning at reduced RPM
Standby_Y Heads unloaded. Disks spinning at reduced RPM.
Recovery requires the NOTIFY (Enable Spinup) command.
Standby_Z Heads unloaded. Motor stopped (disks not spinning)
Recovery requires the NOTIFY (Enable Spinup) command.
Note Processing the Request Sense command does not impact the drive’s power save state.
Seagate Enterprise Capacity 3.5 HDD v5 SAS Product Manual, Rev. E 24
6.2 AC power requirements
None.
6.3 DC power requirements
The voltage and current requirements for a single drive are shown below. Values indicated apply at the drive connector.
The standard drive models and the SED drive models have identical hardware, however the security and encryption portion of the drive controller
ASIC is enabled and functional in the SED models. This represents a small additional drain on the 5V supply of about 30mA and a commensurate
increase of about 150mW in power consumption. There is no additional drain on the 12V supply.
Table 13 3-4TB drive DC power requirements
Notes
6.0Gb mode 12.0Gb mode
(Amps) (Amps) (Watts) (Amps) (Amps) (Watts)
Voltage +5V +12V [2] +5V +12V [2]
Regulation [5] ± 5% [2] ± 5% [2]
Avg idle current DCX [1] [7] 0.33 0.41 6.52 0.401 0.380 6.56
Advanced idle current
Idle A 3s 0.33 0.41 6.52 0.390 0.378 6.48
Idle B 3s 0.33 0.36 5.96 0.317 0.340 5.67
Idle C 3s 0.34 0.21 4.23 0.326 0.208 4.13
Standby 3s 0.32 0.01 1.64 0.307 0.006 1.60
Maximum starting current
(peak DC) DC 3s [3] 0.68 2.13 28.96 0.727 2.080 28.60
(peak AC) AC 3s [3] 0.90 2.71 1.016 2.760
Delayed motor start (max) DC 3s [1] [4] 0.36 0.03 0.368 0.072
Operating current (random read 4K 16Q)
Typical DCX [1] [6] 0.44 0.68 10.39 0.436 0.721 10.83
Maximum DC 3s [1] 0.52 0.72 0.441 0.726
Maximum (peak) DC 3s 1.54 2.38 1.155 2.313
Operating current (random write 4K 16Q)
Typical DCX [1] 0.44 0.59 9.32 0.448 0.694 10.57
Maximum DC 3s [1] 0.54 0.74 0.455 0.703
Maximum (peak) DC 3s 1.60 2.38 0.743 2.295
Operating current (sequential read 64K 16Q)
Typical DCX [1] 0.75 0.43 8.87 0.750 0.410 8.67
Maximum DC 3s [1] 0.86 0.45 0.757 0.414
Maximum (peak) DC 3s 1.12 2.58 0.988 1.824
Operating current (sequential write 64K 16Q)
Typical DCX [1] 0.63 0.44 8.48 0.669 0.429 8.49
Maximum DC 3s [1] 0.74 0.47 0.678 0.433
Maximum (peak) DC 3s 0.88 0.87 0.920 0.840
Seagate Enterprise Capacity 3.5 HDD v5 SAS Product Manual, Rev. E 25
Table 14 1-2TB drive DC power requirements
Notes
6.0Gb mode 12.0Gb mode
(Amps) (Amps) (Watts) (Amps) (Amps) (Watts)
Voltage +5V +12V [2] +5V +12V [2]
Regulation [5] ± 5% [2] ± 5% [2]
Avg idle current DCX [1] [7] 0.30 0.26 4.57 0.421 0.246 5.06
Advanced idle current
Idle A 3s 0.31 0.26 4.60 0.411 0.247 5.02
Idle B 3s 0.29 0.23 4.21 0.337 0.222 4.35
Idle C 3s 0.31 0.15 3.32 0.346 0.143 3.45
Standby 3s 0.28 0.01 1.51 0.327 0.007 1.72
Maximum starting current
(peak DC) DC 3s [3] 0.54 2.03 27.06 0.746 2.047 28.29
(peak AC) AC 3s [3] 0.70 2.61 0.896 2.620
Delayed motor start (max) DC 3s [1] [4] 0.28 0.10 0.388 0.068
Operating current (random read 4K 16Q)
Typical DCX [1] [6] 0.41 0.59 9.10 0.455 0.594 9.41
Maximum DC 3s [1] 0.43 0.61 0.476 0.599
Maximum (peak) DC 3s 1.23 2.33 1.15 2.114
Operating current (random write 4K 16Q)
Typical DCX [1] 0.41 0.44 7.35 0.466 0.560 9.05
Maximum DC 3s [1] 0.44 0.58 0.485 0.568
Maximum (peak) DC 3s 1.50 2.15 0.758 2.113
Operating current (sequential read 64K 16Q)
Typical DCX [1] 0.72 0.27 6.86 0.759 0.276 7.11
Maximum DC 3s [1] 0.75 0.29 0.782 0.279
Maximum (peak) DC 3s 0.98 1.99 1.039 1.824
Operating current (sequential write 64K 16Q)
Typical DCX [1] 0.61 0.29 6.51 0.688 0.301 7.05
Maximum DC 3s [1] 0.65 0.30 0.708 0.306
Maximum (peak) DC 3s 0.82 2.91 0.902 0.674
Seagate Enterprise Capacity 3.5 HDD v5 SAS Product Manual, Rev. E 26
[1] Measured with average reading DC ammeter. Instantaneous +12V current peaks will exceed these values. Power supply at nominal voltage. N
(number of drives tested) = 6, 35 Degrees C ambient.
[2] For +12 V, a –10% tolerance is allowed during initial spindle start but must return to ± 5% before reaching 7200 RPM. The ± 5% must be main-
tained after the drive signifies that its power-up sequence has been completed and that the drive is able to accept selection by the host initia-
tor.
[3] See +12V current profile in Figure 1. (for 4TB models)
[4] This condition occurs after OOB and Speed Negotiation completes but before the drive has received the Notify Spinup primitive.
[5] See paragraph 6.3.1, "Conducted noise immunity." Specified voltage tolerance includes ripple, noise, and transient response.
[6] Operating condition is defined as random 8 block reads.
[7] During idle, the drive heads are relocated every 60 seconds to a random location within the band from three-quarters to maximum track.
General DC power requirement notes.
1. Minimum current loading for each supply voltage is not less than 1.7% of the maximum operating current shown.
2. The +5V and +12V supplies should employ separate ground returns.
3. Where power is provided to multiple drives from a common supply, careful consideration for individual drive power requirements should be
noted. Where multiple units are powered on simultaneously, the peak starting current must be available to each device.
4. Parameters, other than spindle start, are measured after a 10-minute warm up.
5. No terminator power.
6.3.1 Conducted noise immunity
Noise is specified as a periodic and random distribution of frequencies covering a band from DC to 10 MHz. Maximum allowed noise values given
below are peak-to-peak measurements and apply at the drive power connector.
6.3.2 Power sequencing
The drive does not require power sequencing. The drive protects against inadvertent writing during power-up and down.
+5v = 250 mV pp from 100 Hz to 20 MHz.
+12v = 800 mV pp from 100 Hz to 8 KHz.
450 mV pp from 8 KHz to 20 KHz.
250 mV pp from 20 KHz to 5 MHz.
Seagate Enterprise Capacity 3.5 HDD v5 SAS Product Manual, Rev. E 27
6.3.3 Current profiles
The +12V (top) and +5V (bottom) current profiles for the Enterprise Capacity 3.5 HDD drives are shown below.
Figure 1. 4TB and 3TB models current profiles
The +12V (top) and +5V (bottom) current profiles for the Enterprise Capacity 3.5 HDD drives are shown below.
Figure 2. 2TB and 1TB models current profiles
Note All times and currents are typical. See Table 14 for maximum current requirements.
Seagate Enterprise Capacity 3.5 HDD v5 SAS Product Manual, Rev. E 28
6.4 Power dissipation
4TB and 3TB models in 12Gb operation
Please refer to Table 13 for power dissipation numbers.
To obtain operating power for typical random read operations, refer to the following I/O rate curve (see Figure 3). Locate the typical I/O rate for a
drive in the system on the horizontal axis and read the corresponding +5 volt current, +12 volt current, and total watts on the vertical axis. To
calculate BTUs per hour, multiply watts by 3.4123.
Figure 3. 4TB and 3TB models (12Gb) DC current and power vs. input/output operations per second
2TB and 1TB models in 12Gb operation
Please refer to Table 14 for power dissipation numbers.
To obtain operating power for typical random read operations, refer to the following I/O rate curve (see Figure 4.). Locate the typical I/O rate for a
drive in the system on the horizontal axis and read the corresponding +5 volt current, +12 volt current, and total watts on the vertical axis. To
calculate BTUs per hour, multiply watts by 3.4123.
Figure 4. 2TB and 1TB models (12Gb) DC current and power vs. input/output operations per second
Seagate Enterprise Capacity 3.5 HDD v5 SAS Product Manual, Rev. E 29
6.5 Environmental limits
Temperature and humidity values experienced by the drive must be such that condensation does not occur on any drive part. Altitude and
atmospheric pressure specifications are referenced to a standard day at 58.7°F (14.8°C).
6.5.1 Temperature
a. Operating
The drive meets the operating specifications over a 41°F to 140°F (5°C to 60°C) drive case temperature range with a maximum temperature
gradient of 36°F (20°C) per hour.
The maximum allowable drive case temperature is 140°F (60°C).
Air flow may be required to achieve consistent nominal case temperature values (see Section 10.2). To confirm that the required cooling is
provided for the electronics and HDA, place the drive in its final mechanical configuration, and perform random write/read operations. After the
temperatures stabilize, measure the case temperature of the drive. See Figure 5 for HDA case temperature measurement location.
b. Non-operating
–40° to 158°F (–40° to 70°C) package ambient with a maximum gradient of 36°F (20°C) per hour. This specification assumes that the drive is
packaged in the shipping container designed by Seagate for use with drive.
Figure 5. Location of the HDA temperature check point
6.5.2 Humidity
The values below assume that no condensation on the drive occurs. Maximum wet bulb temperature is 84.2°F (29°C).
a. Operating
5% to 95% non-condensing relative humidity with a maximum gradient of 20% per hour.
b. Non-operating
5% to 95% non-condensing relative humidity.
6.5.3 Effective altitude (sea level)
a. Operating
–1000 to +10,000 feet (–304.8 to +3048 meters)
b. Non-operating
–1000 to +40,000 feet (–304.8 to +12,192 meters)
Note To maintain optimal performance drives should be run at nominal drive temperatures and humidity
Note Image is for reference only, may not represent actual drive.
HDA Temp.
Check Point
Seagate Enterprise Capacity 3.5 HDD v5 SAS Product Manual, Rev. E 30
6.5.4 Shock and vibration
Shock and vibration limits specified in this document are measured directly on the drive chassis. If the drive is installed in an enclosure to which the
stated shock and/or vibration criteria is applied, resonances may occur internally to the enclosure resulting in drive movement in excess of the
stated limits. If this situation is apparent, it may be necessary to modify the enclosure to minimize drive movement.
The limits of shock and vibration defined within this document are specified with the drive mounted by any of the four methods shown in Figure 6,
and in accordance with the restrictions of Section 10.3.
6.5.4.1 Shock
a. Operating—normal
The drive, as installed for normal operation, shall operate error free while subjected to intermittent shock not exceeding 70 Gs (read) and 40 Gs
(write) at a maximum duration of 2ms (half sinewave). Shock may be applied in the X, Y, or Z axis. Shock is not to be repeated more than once
every 2 seconds.
b. Operating—abnormal
Equipment, as installed for normal operation, does not incur physical damage while subjected to intermittent shock not exceeding 40 Gs at a
maximum duration of 11ms (half sinewave). Shock occurring at abnormal levels may promote degraded operational performance during the
abnormal shock period. Specified operational performance will continue when normal operating shock levels resume. Shock may be applied in
the X, Y, or Z axis. Shock is not to be repeated more than once every 2 seconds.
c. Non-operating
The limits of non-operating shock shall apply to all conditions of handling and transportation. This includes both isolated drives and integrated
drives.
The drive subjected to nonrepetitive shock not exceeding 80 Gs at a maximum duration of 11ms (half sinewave) shall not exhibit device
damage or performance degradation. Shock may be applied in the X, Y, or Z axis.
The drive subjected to nonrepetitive shock not exceeding 300 Gs at a maximum duration of 2ms (half sinewave) does not exhibit device
damage or performance degradation. Shock may be applied in the X, Y, or Z axis.
The drive subjected to nonrepetitive shock not exceeding 200 Gs at a maximum duration of 0.5ms (half sinewave) does not exhibit device
damage or performance degradation. Shock may be applied in the X, Y, or Z axis.
d. Packaged
Disk drives shipped as loose load (not palletized) general freight will be packaged to withstand drops from heights as defined in the table
below. For additional details refer to Seagate specifications 30190-001 (under 100 lbs/45 kg) or 30191-001 (over 100 lbs/45 Kg).
Seagate Enterprise Capacity 3.5 HDD v5 SAS Product Manual, Rev. E 31
Drives packaged in single or multipacks with a gross weight of 20 pounds (8.95 kg) or less by Seagate for general freight shipment shall
withstand a drop test from 48 in (1070 mm) against a concrete floor or equivalent.
Figure 6. Recommended mounting
Package size Packaged/product weight Drop height
<600 cu in (<9,800 cu cm) Any 60 in (1524 mm)
600-1800 cu in (9,800-19,700 cu cm) 0-20 lb (0 to 9.1 kg) 48 in (1219 mm)
>1800 cu in (>19,700 cu cm) 0-20 lb (0 to 9.1 kg) 42 in (1067 mm)
>600 cu in (>9,800 cu cm) 20-40 lb (9.1 to 18.1 kg) 36 in (914 mm)
Note Image is for reference only, may not represent actual drive.
Z
Y
X
ZY
X
Seagate Enterprise Capacity 3.5 HDD v5 SAS Product Manual, Rev. E 32
6.5.4.2 Vibration
a. Operating—normal
The drive as installed for normal operation, shall comply with the complete specified performance while subjected to continuous vibration not
exceeding
5 - 22 Hz 0.25 Gs, limited displacement
22 - 350 Hz 0.5 Gs
350 - 500 Hz 0.25 Gs
Vibration may be applied in the X, Y, or Z axis.
b. Operating—abnormal
Equipment as installed for normal operation shall not incur physical damage while subjected to periodic vibration not exceeding:
15 minutes of duration at major resonant frequency
Vibration occurring at these levels may degrade operational performance during the abnormal vibration period. Specified operational
performance will continue when normal operating vibration levels are resumed. This assumes system recovery routines are available.
Operating abnormal translational random flat profile
5-500 Hz @ 0.75 G (X, Y, or Z axis)
c. Non-operating
The limits of non-operating vibration shall apply to all conditions of handling and transportation. This includes both isolated drives and
integrated drives.
The drive shall not incur physical damage or degraded performance as a result of continuous vibration not exceeding
5 - 22 Hz 3 Gs (0 to peak, linear, swept sine, 0.5 octave/min)
22 - 350 Hz 3 Gs (0 to peak, linear, swept sine, 0.5 octave/min)
350 - 500 Hz 3 Gs (0 to peak, linear, swept sine, 0.5 octave/min)
Vibration may be applied in the X, Y, or Z axis.
6.5.5 Acoustics
Sound power during idle mode shall be 2.8 bels typical when measured to ISO 7779 specification.
Sound power while operating shall be 3.0 bels typical when measured to ISO 7779 specification.
There will not be any discrete tones more than 9 dB above the masking noise when measured according to
Seagate specification 30553-001.
6.5.6 Air cleanliness
The drive is designed to operate in a typical office environment with minimal environmental control.
6.5.7 Corrosive environment
Seagate electronic drive components pass accelerated corrosion testing equivalent to 10 years exposure to light industrial environments
containing sulfurous gases, chlorine and nitric oxide, classes G and H per ASTM B845. However, this accelerated testing cannot duplicate every
potential application environment.
Users should use caution exposing any electronic components to uncontrolled chemical pollutants and corrosive chemicals as electronic drive
component reliability can be affected by the installation environment. The silver, copper, nickel and gold films used in hard disk drives are especially
sensitive to the presence of sulfide, chloride, and nitrate contaminants. Sulfur is found to be the most damaging. Materials used in cabinet
fabrication, such as vulcanized rubber, that can outgas corrosive compounds should be minimized or eliminated. The useful life of any electronic
equipment may be extended by replacing materials near circuitry with sulfide-free alternatives.
Seagate recommends that data centers be kept clean by monitoring and controlling the dust and gaseous contamination. Gaseous contamination
should be within ANSI/ISA S71.04-2013 G2 classification levels (as measured on copper and silver coupons), and dust contamination to ISO 14644-1
Class 8 standards, and MTBF rated conditions as defined in the Annualized Failure Rate (AFR) and Mean Time Between Failure (MTBF) section.
6.5.8 Electromagnetic susceptibility
See Section 2.1.1.1.
Seagate Enterprise Capacity 3.5 HDD v5 SAS Product Manual, Rev. E 33
6.6 Mechanical specifications
Refer to Figure 7 for detailed mounting configuration dimensions. See Section 10.3, “Drive mounting.”
Figure 7. Mounting configuration dimensions (1TB through 4TB models)
Weight:
4TB 1.500 lb 680 g
3TB 1.500 lb 680 g
2TB 1.340 lb 610 g
1TB 1.340 lb 610 g
Note These dimensions conform to the Small Form Factor Standard
documented in SFF-8301 and SFF-8323, found at www.sffcommittee.org.
Note The image is for mechanical dimension reference only and may not represent the actual drive.
2X 1.750±.010
2X 1.625±.010
4.000±.010
3.750±.010
1.432±.019
2
.128±.010 .814±.020
2
C
L
OF DRIVE
C
L
OF CONN
4X 6-32 UNC 2B
3 MIN THREAD DEPTH
.14 MAX FASTENER PENETRATION
MOUNTING HOLES BOTH SIDES.
MAX TORQUE 6 IN/LBS
Y
5.787 MAX
146.99 MM
2X 4.000±.010
2X 1.638±.010
2X 1.122±.010
.250±.010
6X 6-32 UNC 2B
3 MIN THREAD DEPTH
.14 MAX FASTENER PENETRATION
MOUNTING HOLES BOTH SIDES.
MAX TORQUE 6 IN/LBS
Z
Y
1.028 MAX
26.11 MM
.138±.015
2
2.000
C
L
OF DRIVE
Z
TEMPERATURE
CHECKPOINT 60°C MAX
Seagate Enterprise Capacity 3.5 HDD v5 SAS Product Manual, Rev. E 34
7.0 About FIPS
The Federal Information Processing Standard (FIPS) Publication 140-2 is a U.S. Government Computer Security Standard used to
accredit cryptographic modules. It is titled 'Security Requirements for Cryptographic Modules (FIPS PUB 140-2)' and is issued by the
National Institute of Standards and Technology (NIST).
Purpose
This standard specifies the security requirements that will be satisfied by a cryptographic module utilized within a security system
protecting sensitive but unclassified information. The standard provides four increasing, qualitative levels of security: Level 1, Level 2,
Level 3 and Level 4. These levels are intended to cover the wide range of potential applications and environments in which
cryptographic modules may be employed.
Validation Program
Products that claim conformance to this standard are validated by the Cryptographic Module Validation Program (CMVP) which is a
joint effort between National Institute of Standards and Technology (NIST) and the Communications Security Establishment (CSE) of
the Government of Canada. Products validated as conforming to FIPS 140-2 are accepted by the Federal agencies of both countries
for the protection of sensitive information (United States) or Designated Information (Canada).
In the CMVP, vendors of cryptographic modules use independent, accredited testing laboratories to have their modules tested.
National Voluntary Laboratory Accreditation Program (NVLAP) accredited laboratories perform cryptographic module compliance/
conformance testing.
Seagate Enterprise SED
The SEDs referenced in this Product Manual have been validated by CMVP and have been thoroughly tested by a NVLAP accredited
lab to satisfy FIPS 140-2 Level 2 requirements. In order to operate in FIPS Approved Mode of Operation, these SEDs require security
initialization. For more information, refer to 'Security Rules' section in the 'Security Policy' document uploaded on the NIST website.
To reference the product certification visit - http://csrc.nist.gov/groups/STM/cmvp/documents/140-1/1401vend.htm, and search for
“Seagate”.
Security Level 2
Security Level 2 enhances the physical security mechanisms of a Security Level 1 cryptographic module by adding the require-
ment for tamper-evidence, which includes the use of tamper-evident coatings or seals on removable covers of the module. Tam-
per-evident coatings or seals are placed on a cryptographic module so that the coating or seal must be broken to attain physical
access to the critical security parameters (CSP) within the module. Tamper-evident seals (example shown in Figure 8, page 34) are
placed on covers to protect against unauthorized physical access. In addition Security Level 2 requires, at a minimum, role-based
authentication in which a cryptographic module authenticates the authorization of an operator to assume a specific role and per-
form a corresponding set of services.
Figure 8. Example of FIPS tamper evidence labels.
Note Image is for reference only, may not represent actual drive.
Seagate Enterprise Capacity 3.5 HDD v5 SAS Product Manual, Rev. E 35
8.0 About self-encrypting drives
Self-encrypting drives (SEDs) offer encryption and security services for the protection of stored data, commonly known as “protection of data at
rest.” These drives are compliant with the Trusted Computing Group (TCG) Enterprise Storage Specifications as detailed in Section 2.2.
The Trusted Computing Group (TCG) is an organization sponsored and operated by companies in the computer, storage and digital
communications industry. Seagate’s SED models comply with the standards published by the TCG.
To use the security features in the drive, the host must be capable of constructing and issuing the following two SCSI commands:
• Security Protocol Out
• Security Protocol In
These commands are used to convey the TCG protocol to and from the drive in their command payloads.
8.1 Data encryption
Encrypting drives use one inline encryption engine for each port, employing AES-256 data encryption in Cipher Block Chaining (CBC) mode to
encrypt all data prior to being written on the media and to decrypt all data as it is read from the media. The encryption engines are always in
operation and cannot be disabled.
The 32-byte Data Encryption Key (DEK) is a random number which is generated by the drive, never leaves the drive, and is inaccessible to the host
system. The DEK is itself encrypted when it is stored on the media and when it is in volatile temporary storage (DRAM) external to the encryption
engine. A unique data encryption key is used for each of the drive's possible16 data bands (see Section 8.5).
8.2 Controlled access
The drive has two security providers (SPs) called the "Admin SP" and the "Locking SP." These act as gatekeepers to the drive security services.
Security-related commands will not be accepted unless they also supply the correct credentials to prove the requester is authorized to perform the
command.
8.2.1 Admin SP
The Admin SP allows the drive's owner to enable or disable firmware download operations (see Section 8.4). Access to the Admin SP is available
using the SID (Secure ID) password or the MSID (Manufacturers Secure ID) password.
8.2.2 Locking SP
The Locking SP controls read/write access to the media and the cryptographic erase feature. Access to the Locking SP is available using the
BandMasterX or EraseMaster passwords. Since the drive owner can define up to 16 data bands on the drive, each data band has its own password
called BandMasterX where X is the number of the data band (0 through 15).
8.2.3 Default password
When the drive is shipped from the factory, all passwords are set to the value of MSID. This 32-byte random value can only be read by the host
electronically over the interface. After receipt of the drive, it is the responsibility of the owner to use the default MSID password as the authority to
change all other passwords to unique owner-specified values.
8.3 Random number generator (RNG)
The drive has a 32-byte hardware RNG that it is uses to derive encryption keys or, if requested to do so, to provide random numbers to the host for
system use, including using these numbers as Authentication Keys (passwords) for the drive’s Admin and Locking SPs.
8.4 Drive locking
In addition to changing the passwords, as described in Section 8.2.3, the owner should also set the data access controls for the individual bands.
The variable "LockOnReset" should be set to "PowerCycle" to ensure that the data bands will be locked if power is lost. In addition
"ReadLockEnabled" and "WriteLockEnabled" must be set to true in the locking table in order for the bands "LockOnReset" setting of "PowerCycle" to
actually lock access to the band when a "PowerCycle" event occurs. This scenario occurs if the drive is removed from its cabinet. The drive will not
honor any data read or write requests until the bands have been unlocked. This prevents the user data from being accessed without the appropriate
credentials when the drive has been removed from its cabinet and installed in another system.
When the drive is shipped from the factory, the firmware download port is unlocked.
Seagate Enterprise Capacity 3.5 HDD v5 SAS Product Manual, Rev. E 36
8.5 Data bands
When shipped from the factory, the drive is configured with a single data band called Band 0 (also known as the Global Data Band) which comprises
LBA 0 through LBA max. The host may allocate Band1 by specifying a start LBA and an LBA range. The real estate for this band is taken from the
Global Band. An additional 14 Data Bands may be defined in a similar way (Band2 through Band15) but before these bands can be allocated LBA
space, they must first be individually enabled using the EraseMaster password.
Data bands cannot overlap but they can be sequential with one band ending at LBA (x) and the next beginning at LBA (x+1).
Each data band has its own drive-generated encryption key and its own user-supplied password. The host may change the Encryption Key (see
Section 8.6) or the password when required. The bands should be aligned to 4K LBA boundaries.
8.6 Cryptographic erase
A significant feature of SEDs is the ability to perform a cryptographic erase. This involves the host telling the drive to change the data encryption key
for a particular band. Once changed, the data is no longer recoverable since it was written with one key and will be read using a different key. Since
the drive overwrites the old key with the new one, and keeps no history of key changes, the user data can never be recovered. This is tantamount to
an instantaneous data erase and is very useful if the drive is to be scrapped or redispositioned.
8.7 Authenticated firmware download
In addition to providing a locking mechanism to prevent unwanted firmware download attempts, the drive also only accepts download files which
have been cryptographically signed by the appropriate Seagate Design Center.
Three conditions must be met before the drive will allow the download operation:
1. The download must be an SED file. A standard (base) drive (non-SED) file will be rejected.
2. The download file must be signed and authenticated.
3. As with a non-SED drive, the download file must pass the acceptance criteria for the drive. For example it must be applicable to the correct
drive model, and have compatible revision and customer status.
8.8 Power requirements
The standard drive models and the SED drive models have identical hardware, however the security and encryption portion of the drive controller
ASIC is enabled and functional in the SED models. This represents a small additional drain on the 5V supply of about 30mA and a commensurate
increase of about 150mW in power consumption. There is no additional drain on the 12V supply. See the tables in Section 6.3 for power
requirements on the standard (non-SED) drive models.
8.9 Supported commands
The SED models support the following two commands in addition to the commands supported by the standard (non-SED) models as listed in Table
18:
• Security Protocol Out (B5h)
• Security Protocol In (A2h)
8.10 Sanitize - CRYPTOGRAPHIC ERASE
This command cryptographically erases all user data on the drive by destroying the current data encryption key and replacing it with a new data
encryption key randomly generated by the drive. Sanitize CRYPTOGRAPHIC ERASE is a SCSI CDB Op code 48h and selecting the service action code
3 (CRYPTOGRAPHIC ERASE)
8.11 RevertSP
SED models will support the RevertSP feature which erases all data in all bands on the device and returns the contents of all SPs (Security Providers)
on the device to their original factory state. In order to execute the RevertSP method the unique PSID (Physical Secure ID) printed on the drive label
must be provided. PSID is not electronically accessible and can only be manually read from the drive label or scanned in via the 2D barcode.
Seagate Enterprise Capacity 3.5 HDD v5 SAS Product Manual, Rev. E 37
9.0 Defect and error management
Seagate continues to use innovative technologies to manage defects and errors. These technologies are designed to increase data integrity,
perform drive self-maintenance, and validate proper drive operation.
SCSI defect and error management involves drive internal defect/error management and SAS system error considerations (errors in
communications between the initiator and the drive). In addition, Seagate provides the following technologies used to increase data integrity and
drive reliability:
• Background Media Scan (see Section 9.4)
• Media Pre-Scan (see Section 9.5)
• Deferred Auto-Reallocation (see Section 9.6)
• Idle Read After Write (see Section 9.7)
The read error rates and specified storage capacities are not dependent on host (initiator) defect management routines.
9.1 Drive internal defects/errors
During the initial drive format operation at the factory, media defects are identified, tagged as being unusable, and their locations recorded on the
drive primary defects list (referred to as the “P’ list and also as the ETF defect list). At factory format time, these known defects are also reallocated,
that is, reassigned to a new place on the medium and the location listed in the defects reallocation table. The “P” list is not altered after factory
formatting. Locations of defects found and reallocated during error recovery procedures after drive shipment are listed in the “G” list (defects
growth list). The “P” and “G” lists may be referenced by the initiator using the Read Defect Data command.
Details of the SCSI commands supported by the drive are described in the SAS Interface Manual. Also, more information on the drive Error Recovery
philosophy is presented in the SAS Interface Manual.
9.2 Drive error recovery procedures
When an error occurs during drive operation, the drive, if programmed to do so, performs error recovery procedures to attempt to recover the data.
The error recovery procedures used depend on the options previously set in the Error Recovery Parameters mode page. Error recovery and defect
management may involve using several SCSI commands described in the SAS Interface Manual. The drive implements selectable error recovery time
limits required in video applications.
The error recovery scheme supported by the drive provides a way to control the total error recovery time for the entire command in addition to
controlling the recovery level for a single LBA. The total amount of time spent in error recovery for a command can be limited using the Recovery
Time Limit bytes in the Error Recovery mode page. The total amount of time spent in error recovery for a single LBA can be limited using the Read
Retry Count or Write Retry Count bytes in the Error Recovery mode page.
The drive firmware error recovery algorithms consist of 12 levels for read recoveries and five levels for write. Each level may consist of multiple steps,
where a step is defined as a recovery function involving a single re-read or re-write attempt. The maximum level used by the drive in LBA recovery is
determined by the read and write retry counts.
Table 15 equates the read and write retry count with the maximum possible recovery time for read and write recovery of individual LBAs. The times
given do not include time taken to perform reallocations. Reallocations are performed when the ARRE bit (for reads) or AWRE bit (for writes) is one,
the RC bit is zero, and the recovery time limit for the command has not yet been met. Time needed to perform reallocation is not counted against
the recovery time limit.
When the RC bit is one, reallocations are disabled even if the ARRE or AWRE bits are one. The drive will still perform data recovery actions within the
limits defined by the Read Retry Count, Write Retry Count, and Recovery Time Limit parameters. However, the drive does not report any
unrecovered errors.
Seagate Enterprise Capacity 3.5 HDD v5 SAS Product Manual, Rev. E 38
* For read retry count, every tick ~ 5% of total error recovery. Valid range setting is 1-20.
e.g. 1 ~ 5%
5 ~ 25%
20 ~ 100%
Setting these retry counts to a value below the default setting could result in degradation of the unrecovered error rate. For example, suppose the
read/write recovery page has the RC bit = 0 and if the read retry count is set to 5, this means ~ 25% of error recovery will be executed which
consumes 621.62 ms (please refer to the table above). If the limit is reached and a LBA has not yet been recovered (i.e. requires retries beyond
621.62 ms), the command will end with Check Condition status report and unrecoverable read error will be reported.
9.3 SAS system errors
Information on the reporting of operational errors or faults across the interface is given in the SAS Interface Manual. The SSP Response returns
information to the host about numerous kinds of errors or faults. The Receive Diagnostic Results reports the results of diagnostic operations
performed by the drive.
Status returned by the drive to the initiator is described in the SAS Interface Manual. Status reporting plays a role in systems error management and
its use in that respect is described in sections where the various commands are discussed.
Table 15 Read and write retry count maximum recovery times
Read retry count*
Maximum recovery time per
LBA (cumulative, ms) Write retry count
Maximum recovery time per
LBA (cumulative, ms)
0 35.94
1 124.32 1 53.91
5 621.62 2 79.89
10 1243.23 3 97.86
15 1864.85 4 175.85
20 (default) 2486.47 5 (default) 421.79
Seagate Enterprise Capacity 3.5 HDD v5 SAS Product Manual, Rev. E 39
9.4 Background Media Scan
Background Media Scan (BMS) is a self-initiated media scan. BMS is defined in the T10 document SPC-4 available from the T10 committee. BMS
performs sequential reads across the entire pack of the media while the drive is idle. In RAID arrays, BMS allows hot spare drives to be scanned for
defects prior to being put into service by the host system. On regular duty drives, if the host system makes use of the BMS Log Page, it can avoid
placing data in suspect locations on the media. Unreadable and recovered error sites will be logged or reallocated per ARRE/AWRE settings.
With BMS, the host system can consume less power and system overhead by only checking BMS status and results rather than tying up the bus and
consuming power in the process of host-initiated media scanning activity.
Since the background scan functions are only done during idle periods, BMS causes a negligible impact to system performance. The first BMS scan
for a newly manufactured drive is performed as quickly as possible to verify the media and protect data by setting the “Start time after idle” to 5ms,
all subsequent scans begin after 500ms of idle time. Other features that normally use idle time to function will function normally because BMS
functions for bursts of 800ms and then suspends activity for 100ms to allow other background functions to operate.
BMS interrupts immediately to service host commands from the interface bus while performing reads. BMS will complete any BMS-initiated error
recovery prior to returning to service host-initiated commands. Overhead associated with a return to host-servicing activity from BMS only impacts
the first command that interrupted BMS, this results in a typical delay of about 1 ms.
9.5 Media Pre-Scan
Media Pre-Scan is a feature that allows the drive to repair media errors that would otherwise have been found by the host system during critical
data accesses early in the drive’s life. The default setting for Media Pre-Scan is enabled on standard products. Media Pre-Scan checks each write
command to determine if the destination LBAs have been scanned by BMS. If the LBAs have been verified, the drive proceeds with the normal write
command. If the LBAs have not been verified by BMS, Pre-Scan will convert the write to a write verify to certify that the data was properly written to
the disk.
To expedite the scan of the full pack and subsequently exit from the Pre-Scan period, BMS will begin scanning immediately when the drive goes to
idle during the Pre-Scan period. In the event that the drive is in a high transaction traffic environment and is unable to complete a BMS scan within
24 power on hours BMS will disable Pre-Scan to restore full performance to the system.
9.6 Deferred Auto-Reallocation
Deferred Auto-Reallocation (DAR) simplifies reallocation algorithms at the system level by allowing the drive to reallocate unreadable locations on a
subsequent write command. Sites are marked for DAR during read operations performed by the drive. When a write command is received for an
LBA marked for DAR, the auto-reallocation process is invoked and attempts to rewrite the data to the original location. If a verification of this rewrite
fails, the sector is re-mapped to a spare location.
This is in contrast to the system having to use the Reassign Command to reassign a location that was unreadable and then generate a write
command to rewrite the data. DAR is most effective when AWRE and ARRE are enabled—this is the default setting from the Seagate factory. With
AWRE and ARRE disabled DAR is unable to reallocate the failing location and will report an error sense code indicating that a write command is
being attempted to a previously failing location.
9.7 Idle Read After Write
Idle Read After Write (IRAW) utilizes idle time to verify the integrity of recently written data. During idle periods, no active system requests, the drive
reads recently written data from the media and compares it to valid write command data resident in the drives data buffer. Any sectors that fail the
comparison result in the invocation of a rewrite and auto-reallocation process. The process attempts to rewrite the data to the original location. If a
verification of this rewrite fails, the sector is re-mapped to a spare location.
Note During Pre-Scan write verify commands, write performance may decrease by 50% until Pre-Scan completes. Write performance
testing should be performed after Pre-Scan is complete. This may be checked by reading the BMS status.
Seagate Enterprise Capacity 3.5 HDD v5 SAS Product Manual, Rev. E 40
9.8 Protection Information (PI)
Protection Information is intended as a standardized approach to system level LRC traditionally provided by systems using 520 byte formatted
LBAs. Drives formatted with PI information provide the same, common LBA count (i.e. same capacity point) as non-PI formatted drives. Sequential
performance of a PI drive will be reduced by approximately 1.56% due to the extra overhead of PI being transferred from the media that is not
calculated as part of the data transferred to the host. To determine the full transfer rate of a PI drive, transfers should be calculated by adding the 8
extra bytes of PI to the transferred LBA length, i.e. 512 + 8 = 520. PI formatted drives are physically formatted to 520 byte sectors that store 512 bytes
of customer data with 8 bytes of Protection Information appended to it. The advantage of PI is that the Protection Information bits can be managed
at the HBA and HBA driver level. Allowing a system that typically does not support 520 LBA formats to integrate this level of protection.
Protection Information is valid with any supported LBA size. 512 LBA size is used here as common example.
9.8.1 Levels of PI
There are 4 types of Protection Information.
Type 0 - Describes a drive that is not formatted with PI information bytes. This allows for legacy support in non-PI systems.
Type 1 - Provides support of PI protection using 10 and 16 byte commands. The RDPROTECT and WRTPROTECT bits allow for checking control
through the CDB. Eight bytes of Protection Information are transmitted at LBA boundaries across the interface if RDPROTECT and WRTPROTECT bits
are nonzero values. Type 1 does not allow the use of 32 byte commands.
Type 2 - Provides checking control and additional expected fields within the 32 byte CDBs. Eight bytes of Protection Information are transmitted at
LBA boundaries across the interface if RDPROTECT and WRTPROTECT bits are nonzero values. Type 2 does allow the use of 10 and 16 byte
commands with zero values in the RDPROTECT and WRTPROTECT fields. The drive will generate 8 bytes (e.g.0xFFFF) 8 bytes of Protection
Information to be stored on the media, but the 8 bytes will not be transferred to the host during a read command.
Type 3 - Seagate products do not support Type 3.
9.8.2 Setting and determining the current Type Level
A drive is initialized to a type of PI by using the format command on a PI capable drive. Once a drive is formatted to a PI Type, it may be queried by a
Read Capacity (16) command to report the PI type which it is currently formatted to. PI Types cannot coexist on a single drive. A drive can only be
formatted to a single PI Type. It can be changed at anytime to a new Type but requires a low level format which destroys all existing data on the
drive. No other vehicle for changing the PI type is provided by the T10 SBC3 specification.
Type 1 PI format CDB command: 04 90 00 00 00 00, Write Buffer: 00 A0 00 00
Type 2 PI format CDB command: 04 D0 00 00 00 00, Write Buffer: 00 A0 00 00
9.8.3 Identifying a Protection Information drive
The Standard Inquiry provides a bit to indicate if PI is support by the drive. Vital Product Descriptor (VPD) page 0x86 provides bits to indicate the PI
Types supported and which PI fields the drive supports checking.
Note For further details with respect to PI, please refer to SCSI Block Commands - 3 (SBC-3) Draft Standard documentation.
Seagate Enterprise Capacity 3.5 HDD v5 SAS Product Manual, Rev. E 41
10.0 Installation
Enterprise Capacity 3.5 HDD v5 disk drive installation is a plug-and-play process. There are no jumpers, switches, or terminators on the drive.
SAS drives are designed to be used in a host system that provides a SAS-compatible backplane with bays designed to accommodate the drive. In
such systems, the host system typically provides a carrier or tray into which users need to mount the drive. Mount the drive to the carrier or tray
provided by the host system only using 6-32 UNC mounting screws. The screws should be inserted no more than 0.140 in (3.56mm) into the bottom
or side mounting holes. When tightening the screws, do not overtighten use a maximum torque of 6 in-lb. Users can mount the drive in any
orientation.
Slide the carrier or tray into the appropriate bay in the host system using the instructions provided by the host system. This connects the drive
directly to the system’s SAS connector. The SAS connector is normally located on a SAS backpanel. See Section 11.4.1 for additional information
about these connectors.
Power is supplied through the SAS connector.
The drive is shipped from the factory low-level formatted in 512-byte logical blocks. Users need to reformat the drive only if selecting a different
logical block size.
Figure 9. Physical interface
10.1 Drive orientation
The drive may be mounted in any orientation. All drive performance characterizations, however, have been done with the drive in horizontal (discs
level) and vertical (drive on its side) orientations, which are the two preferred mounting orientations.
Note
SAS drives are designed to be attached to the host system without I/O or power cables. If users
intend the use the drive in a non-backplane host system, connecting the drive using high-quality
cables is acceptable as long as the I/O cable length does not exceed 4 meters (13.1 feet).
Note Image is for reference only, may not represent actual drive.
Seagate Enterprise Capacity 3.5 HDD v5 SAS Product Manual, Rev. E 42
10.2 Cooling
Cabinet cooling must be designed by the customer so that the ambient temperature immediately surrounding the drive will not exceed
temperature conditions specified in Section 6.5.1, "Temperature."
The rack, cabinet, or drawer environment for the drive must provide heat removal from the electronics and head and disk assembly (HDA). Users
should confirm that adequate heat removal is provided using the temperature measurement guidelines described in Section 6.5.1.
Forced air flow may be required to keep temperatures at or below the temperatures specified in Section 6.5.1 in which case the drive should be
oriented, or air flow directed, so that the least amount of air flow resistance is created while providing air flow to the electronics and HDA. Also, the
shortest possible path between the air inlet and exit should be chosen to minimize the travel length of air heated by the drive and other heat
sources within the rack, cabinet, or drawer environment.
If forced air is determined to be necessary, possible air-flow patterns are shown in Figure 10. The air-flow patterns are created by one or more fans,
either forcing or drawing air as shown in the illustrations. Conduction, convection, or other forced air-flow patterns are acceptable as long as the
temperature measurement guidelines of Section 6.5.1 are met.
Figure 10. Air flow
Note Image is for reference only, may not represent actual drive.
Above unit
Under unit
Note. Air flows in the direction shown (back to front)
or in reverse direction (front to back)
Above unit
Under unit
Note. Air flows in the direction shown or
in reverse direction (side to side)
Seagate Enterprise Capacity 3.5 HDD v5 SAS Product Manual, Rev. E 43
10.3 Drive mounting
Mount the drive using the bottom or side mounting holes. If mounting the drive using the bottom holes, ensure the drive is not physically distorted
by attempting to mount it on a stiff, non-flat surface.
The allowable mounting surface stiffness is 80 lb/in (14.0 N/mm). The following equation and paragraph define the allowable mounting surface
stiffness:
where K is the mounting surface stiffness (units in lb/in or N/mm) and X is the out-of-plane surface distortion (units in inches or millimeters). The
out-of-plane distortion (X) is determined by defining a plane with three of the four mounting points fixed and evaluating the out-of-plane
deflection of the fourth mounting point when a known force (F) is applied to the fourth point.
Figure 11. Breather hole location - top cover
10.4 Grounding
Signal ground (PCBA) and HDA ground are connected together in the drive and cannot be separated by the user. The equipment in which the drive
is mounted is connected directly to the HDA and PCBA with no electrically isolating shock mounts. If it is desired for the system chassis to not be
connected to the HDA/PCBA ground, the systems integrator or user must provide a nonconductive (electrically isolating) method of mounting the
drive in the host equipment.
Increased radiated emissions may result if users do not provide the maximum surface area ground connection between system ground and drive
ground. This is the system designer’s and integrator’s responsibility.
Note Do not cover breather hole on top cover.
K x X = F < 15lb = 67N
Breather Hole
Do Not
Cover
Seagate Enterprise Capacity 3.5 HDD v5 SAS Product Manual, Rev. E 44
11.0 Interface requirements
This section partially describes the interface requirements as implemented on Enterprise Capacity 3.5 HDD v5 drives. Additional information is
provided in the SAS Interface Manual (part number 100293071).
11.1 SAS features
This section lists the SAS-specific features supported by Enterprise Capacity 3.5 HDD v5 drives.
11.1.1 task management functions
Table 16 lists the SAS task management functions supported.
11.1.2 task management responses
Table 17 lists the SAS response codes returned for task management functions supported.
11.2 Dual port support
Enterprise Capacity 3.5 HDD v5 SAS drives have two independent ports. These ports may be connected in the same or different SCSI domains. Each
drive port has a unique SAS address.
The two ports have the capability of independent port clocking (e.g. both ports can run at 12Gb/s or the first port can run at 6Gb/s while the second
port runs at 3Gb/s.) The supported link rates are 3.0, 6.0, or 12.0 Gb/s.
Subject to buffer availability, the Enterprise Capacity 3.5 HDD v5 drives support:
• Concurrent port transfers—The drive supports receiving COMMAND, TASK management transfers on both ports at the same time.
• Full duplex—The drive supports sending XFER_RDY, DATA and RESPONSE transfers while receiving frames on both ports.
Table 16 SAS task management functions supported
Task name Supported
Abort Task Yes
Clear ACA Yes
Clear task set Yes
Abort task set Yes
Logical Unit Reset Yes
Query Task Yes
Table 17 Task management response codes
Function name Response code
Function complete 00
Invalid frame 02
Function not supported 04
Function failed 05
Function succeeded 08
Invalid logical unit 09
Seagate Enterprise Capacity 3.5 HDD v5 SAS Product Manual, Rev. E 45
11.3 SCSI commands supported
Table 18 lists the SCSI commands supported by Enterprise Capacity 3.5 HDD v5 drives.
Table 18 Supported commands
Command name Command code Supported
Change Definition 40h N
Compare 39h N
Copy 18h N
Copy and Verify 3Ah N
Format Unit [1] [5] 04h Y
DCRT bit supported Y
DPRY bit supported N
DSP bit supported Y
IMMED bit supported Y
IP bit supported Y
SI (Security Initialize) bit supported N
STPF bit supported Y
VS (vendor specific) N
Inquiry 12h Y
Block Device Characteristics (B1h) Y
Block Limits (B0h) Y
Date Code page (C1h) Y
Device Behavior page (C3h) Y
Device Identification (83h) Y
Extended Inquiry Data (86h) Y
Firmware Numbers page (C0h) Y
Implemented Operating Def page (81h) Y
Jumper Settings page (C2h) Y
Logical Block Provisioning (B2h) Y
Mode Page Policy (87h) Y
Power Condition (8Ah) Y
Protocol Specific Logical Unit Information (90h) Y
Protocol Specific Port Information (91h) Y
SCSI Ports (88h) Y
Supported Vital Product Data page (00h) Y
Unit Serial Number page (80h) Y
Lock-unlock cache 36h N
Log Select 4Ch Y
PCR bit Y
DU bit N
DS bit Y
TSD bit Y
ETC bit N
TMC bit N
LP bit N
Log Sense 4Dh Y
Application Client Log page (0Fh) N
Buffer Over-run/Under-run page (01h) N
Seagate Enterprise Capacity 3.5 HDD v5 SAS Product Manual, Rev. E 46
Cache Statistics page (37h) Y
Factory Log page (3Eh) Y
Information Exceptions Log page (2Fh) Y
Last n Deferred Errors or Asynchronous Events page (0Bh) N
Last n Error Events page (07h) N
Non-medium Error page (06h) Y
Pages Supported list (00h) Y
Read Error Counter page (03h) Y
Read Reverse Error Counter page (04h) N
Self-test Results page (10h) Y
Start-stop Cycle Counter page (0Eh) Y
Temperature page (0Dh) Y
Verify Error Counter page (05h) Y
Write error counter page (02h) Y
Mode Select (same pages as Mode Sense 1Ah) 15h Y [2]
Mode Select (10) (same pages as Mode Sense 1Ah) 55h Y
Mode Sense 1Ah Y [2]
Caching Parameters page (08h) Y
Control Mode page (0Ah) Y
Disconnect/Reconnect (02h) Y
Error Recovery page (01h) Y
Format page (03h) Y
Information Exceptions Control page (1Ch/01h) Y
Background Scan mode subpage (01h) Y
Notch and Partition Page (0Ch) N
Protocol-Specific Port page (19h) Y
Power Condition page (1Ah) Y
Rigid disk Drive Geometry page (04h) Y
Unit Attention page (00h) Y
Verify Error Recovery page (07h) Y
Xor Control page (10h) N
Mode Sense (10) (same pages as Mode Sense 1Ah) 5Ah Y
Persistent Reserve In 5Eh Y
Persistent Reserve Out 5Fh Y
Prefetch (10) 34h N
Prefetch (16) 90h N.A.
Read (6) 08h Y
Read (10) 28h Y
DPO bit supported Y
FUA bit supported Y
Read (12) A8h N
Read (16) 88h Y
Read (32) 7Fh/0009h N
Read Buffer (modes 0, 2, 3, Ah and Bh supported) 3Ch Y (non-SED drives only)
Read Capacity (10) 25h Y
Table 18 Supported commands
Command name Command code Supported
Seagate Enterprise Capacity 3.5 HDD v5 SAS Product Manual, Rev. E 47
Read Capacity (16) 9Eh/10h Y
Read Defect Data (10) 37h Y
Read Defect Data (12) B7h Y
Read Long 3Eh Y (non-SED drives only)
Read Long (16) 9Eh/11h Y
Reassign Blocks 07h Y
Receive Diagnostic Results 1Ch Y
Supported Diagnostics pages (00h) Y
Translate page (40h) Y
Release 17h Y
Release (10) 57h Y
Report LUNs A0h Y
Request Sense 03h Y
Actual Retry Count bytes Y
Extended Sense Y
Field Pointer bytes Y
Reserve 16h Y
3rd Party Reserve Y
Extent Reservation N
Reserve (10) 56h Y
3rd Party Reserve Y
Extent Reservation N
Rezero Unit 01h Y
Sanitize (CRYPTOGRAPHIC ERASE) 48h Y (SED drives only)
Sanitize (OVERWRITE) 48h Y
Search Data Equal 31h N
Search Data High 30h N
Search Data Low 32h N
Security Protocol In A2h Y (SED models only)
Security Protocol Out B5h Y (SED models only)
Seek (6) 0Bh Y
Seek (10) 2Bh Y
Send Diagnostics 1Dh Y
Supported Diagnostics pages (00h) Y
Translate page (40h) Y
Set Limits 33h N
Start Unit/Stop Unit (spindle ceases rotating) 1Bh Y
Synchronize Cache 35h Y
Synchronize Cache (16) 91h Y
Test Unit Ready 00h Y
Verify (10) 2Fh Y
BYTCHK bit Y
Verify (12) AFh N
Verify (16) AFh Y
Table 18 Supported commands
Command name Command code Supported
Seagate Enterprise Capacity 3.5 HDD v5 SAS Product Manual, Rev. E 48
[1] Enterprise Capacity 3.5 HDD v5 drives can format to 512, 520 or 528 bytes per logical block.
[2] Warning. Power loss during flash programming can result in firmware corruption. This usually makes the drive inoperable.
[3] Reference Mode Sense command 1Ah for mode pages supported.
[4] Y = Yes. Command is supported.
N = No. Command is not supported.
A = Support is available on special request.
[5] Approximately 1.5 increase in time to complete this command for a SED drive versus a non-SED drive of the same capacity.
Verify (32) 7Fh/000Ah N (Supported if formatted for
type 2 protection information)
Write (6) 0Ah Y
Write (10) 2Ah Y
DPO bit Y
FUA bit Y
Write (12) AAh N
Write (16) 8Ah Y
Write (32) 7Fh/000Bh N (Supported if formatted for
type 2 protection information)
Write and Verify (10) 2Eh Y
DPO bit Y
Write and Verify (12) AEh N
Write and Verify (16) 8Eh Y
Write and Verify (32) 7Fh/000Ch N (Supported if formatted for
type 2 protection information)
Write Buffer (modes 0, 2, supported) 3Bh Y (non-SED drives only)
Write Buffer 3Bh
Firmware Download option (modes 5, 7, Ah and Bh) [3] Y (non-SED drives only)
Firmware Download option (modes 4, 5, 7) Y (SED drives only)
Write Long (10) 3Fh Y
Write Long (16) 9Fh/11h Y
Write Same (10) [5] 41h Y
PBdata N
LBdata N
Write Same (16) [5] 93h Y
Write Same (32) 7Fh/000Dh N
XDRead 52h N
XDWrite 50h N
XPWrite 51h N
Table 18 Supported commands
Command name Command code Supported
Seagate Enterprise Capacity 3.5 HDD v5 SAS Product Manual, Rev. E 49
11.3.1 Inquiry data
Table 19 lists the Inquiry command data that the drive should return to the initiator per the format given in the SAS Interface Manual.
Table 19 Enterprise Capacity 3.5 HDD v5 inquiry data
* Copyright year (changes with actual year).
** SCSI Revision support. See the appropriate SPC release documentation for definitions.
PP 10 = Inquiry data for an Inquiry command received on Port A.
30 = Inquiry data for an Inquiry command received on Port B.
R# Four ASCII digits representing the last four digits of the product firmware release number.
S# Eight ASCII digits representing the eight digits of the product serial number.
[ ] Bytes 16 through 26 reflect model of drive. The table above shows the hex values for Model ST4000NM0025.
Refer to the values below for the values of bytes 16 through 26 of a particular model:
ST4000NM0065 53 54 34 30 30 30 4E 4D 30 30 36 35
ST4000NM0135 53 54 34 30 30 30 4E 4D 30 31 33 35
ST3000NM0025 53 54 33 30 30 30 4E 4D 30 30 32 35
ST3000NM0035 53 54 33 30 30 30 4E 4D 30 30 33 35
ST3000NM0045 53 54 33 30 30 30 4E 4D 30 30 34 35
ST2000NM0045 53 54 32 30 30 30 4E 4D 30 30 34 35
ST2000NM0085 53 54 32 30 30 30 4E 4D 30 30 38 35
ST1000NM0045 53 54 31 30 30 30 4E 4D 30 30 34 35
ST1000NM0075 53 54 31 30 30 30 4E 4D 30 30 37 35
Bytes Data (hex)
0-15 00 00 xx** 12 8B 00 30 02 53 45 41 47 41 54 45 20 Vendor ID
16-31 [53 54 34 30 30 30 4E 4D 30 30 32 35} 20 20 20 20 Product ID
32-47 R# R# R# R# S# S# S# S# S# S# S# S# 00 00 00 00
48-63 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
64-79 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80-95 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
96-111 00 43 6F 70 79 72 69 67 68 74 20 28 63 29 20 32* *Copyright
112-127 30* 31* 36* 20 53 65 61 67 61 74 65 20 41 6C 6C 20 notice
128-143 72 69 67 68 74 73 20 72 65 73 65 72 76 65 64 20
Seagate Enterprise Capacity 3.5 HDD v5 SAS Product Manual, Rev. E 50
11.3.2 Mode Sense data
The Mode Sense command provides a way for the drive to report its operating parameters to the initiator. The drive maintains four sets of mode
parameters:
1. Default values
Default values are hard-coded in the drive firmware stored in flash E-PROM (nonvolatile memory) on the drive’s PCB. These default values can
be changed only by downloading a complete set of new firmware into the flash E-PROM. An initiator can request and receive from the drive a
list of default values and use those in a Mode Select command to set up new current and saved values, where the values are changeable.
2. Saved values
Saved values are stored on the drive’s media using a Mode Select command. Only parameter values that are allowed to be changed can be
changed by this method. Parameters in the saved values list that are not changeable by the Mode Select command get their values from
default values storage.
When power is applied to the drive, it takes saved values from the media and stores them as current values in volatile memory. It is not possible
to change the current values (or the saved values) with a Mode Select command before the drive achieves operating speed and is “ready.” An
attempt to do so results in a “Check Condition” status.
On drives requiring unique saved values, the required unique saved values are stored into the saved values storage location on the media prior
to shipping the drive. Some drives may have unique firmware with unique default values also.
On standard OEM drives, the saved values are taken from the default values list and stored into the saved values storage location on the media
prior to shipping.
3. Current values
Current values are volatile values being used by the drive to control its operation. A Mode Select command can be used to change the values
identified as changeable values. Originally, current values are installed from saved or default values after a power on reset, hard reset, or Bus
Device Reset message.
4. Changeable values
Changeable values form a bit mask, stored in nonvolatile memory, that dictates which of the current values and saved values can be changed
by a Mode Select command. A one (1) indicates the value can be changed. A zero (0) indicates the value is not changeable. For example, in
Table 20, refer to Mode page 81, in the row entitled “CHG.” These are hex numbers representing the changeable values for Mode page 81. Note
in columns 5 and 6 (bytes 04 and 05), there is 00h which indicates that in bytes 04 and 05 none of the bits are changeable. Note also that bytes
06, 07, 09, 10, and 11 are not changeable, because those fields are all zeros. In byte 02, hex value FF equates to the binary pattern 11111111. If
there is a zero in any bit position in the field, it means that bit is not changeable. Since all of the bits in byte 02 are ones, all of these bits are
changeable.
The changeable values list can only be changed by downloading new firmware into the flash E-PROM.
The following tables list the values of the data bytes returned by the drive in response to the Mode Sense command pages for SCSI implementation
(see the SAS Interface Manual ).
DEF = Default value. Standard OEM drives are shipped configured this way.
CHG = Changeable bits; indicates if default value is changeable.
Note Because there are often several different versions of drive control firmware in the total population of drives in the field,
the Mode Sense values given in the following tables may not exactly match those of some drives.
Seagate Enterprise Capacity 3.5 HDD v5 SAS Product Manual, Rev. E 51
Table 20 Mode Sense data changeable and default values for 4TB drives
Block Descriptor:
00 00 00 01 D1 C0 BE B0 00 00 00 00 00 00 02 00 (512n)
Mode Pages:
DEF: 00 0A 00 80 0F 00 00 00 00 00 00 00
CHG: 00 0A B7 C0 8F 00 00 00 00 00 FF FF
DEF: 01 0A C0 14 FF 00 00 00 05 00 FF FF
CHG: 01 0A FF FF 00 00 00 00 FF 00 FF FF
DEF: 02 0E 00 00 00 00 00 00 00 00 00 A0 00 00 00 00
CHG: 02 0E 00 00 FF FF 00 00 FF FF FF FF 00 00 00 00
DEF: 03 16 00 01 00 00 00 00 00 02 00 03 02 00 00 01 00 00 00 00 40 00 00 00
CHG: 03 16 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
DEF: 04 16 06 46 40 07 00 00 00 00 00 00 00 00 00 00 00 00 00 00 1C 20 00 00
CHG: 04 16 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
DEF: 07 0A 00 14 FF 00 00 00 00 00 FF FF
CHG: 07 0A 0F FF 00 00 00 00 00 00 FF FF
DEF: 08 12 14 00 FF FF 00 00 FF FF FF FF 80 20 00 00 00 00 00 00
CHG: 08 12 A5 00 00 00 FF FF FF FF 00 00 20 00 00 00 00 00 00 00
DEF: 0A 0A 06 00 00 80 00 00 00 00 4A 4C
CHG: 0A 0A 0F F6 00 00 00 00 00 00 00 00
DEF: 18 06 06 00 00 00 00 00
CHG: 18 06 00 00 00 00 00 00
DEF: 19 0E 46 00 07 D0 00 00 00 00 00 00 00 00 00 00
CHG: 19 0E 50 00 FF FF FF FF FF FF 00 00 00 00 00 00
DEF: 1A 26 00 06 00 00 00 01 00 00 23 28 00 00 04 B0 00 00 17 70 00 00 17 70 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 58
CHG: 1A 26 01 0F FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 FC
DEF: 1C 0A 10 00 00 00 00 00 00 00 00 01
CHG: 1C 0A 9D 0F FF FF FF FF FF FF FF FF
Seagate Enterprise Capacity 3.5 HDD v5 SAS Product Manual, Rev. E 52
Table 21 Mode Sense data changeable and default values for 3TB drives
Block Descriptor:
00 00 00 01 5D 50 A3 B0 00 00 00 00 00 00 02 00 (512n)
Mode Pages:
DEF: 00 0A 00 80 0F 00 00 00 00 00 00 00
CHG: 00 0A B7 C0 8F 00 00 00 00 00 FF FF
DEF: 01 0A C0 14 FF 00 00 00 05 00 FF FF
CHG: 01 0A FF FF 00 00 00 00 FF 00 FF FF
DEF: 02 0E 00 00 00 00 00 00 00 00 00 A0 00 00 00 00
CHG: 02 0E 00 00 FF FF 00 00 FF FF FF FF 00 00 00 00
DEF: 03 16 00 01 00 00 00 00 00 02 00 03 02 00 00 01 00 00 00 00 40 00 00 00
CHG: 03 16 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
DEF: 04 16 05 86 56 07 00 00 00 00 00 00 00 00 00 00 00 00 00 00 1C 20 00 00
CHG: 04 16 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
DEF: 07 0A 00 14 FF 00 00 00 00 00 FF FF
CHG: 07 0A 0F FF 00 00 00 00 00 00 FF FF
DEF: 08 12 14 00 FF FF 00 00 FF FF FF FF 80 20 00 00 00 00 00 00
CHG: 08 12 A5 00 00 00 FF FF FF FF 00 00 20 00 00 00 00 00 00 00
DEF: 0A 0A 06 00 00 80 00 00 00 00 4A 4C
CHG: 0A 0A 0F F6 00 00 00 00 00 00 00 00
DEF: 18 06 06 00 00 00 00 00
CHG: 18 06 00 00 00 00 00 00
DEF: 19 0E 46 00 07 D0 00 00 00 00 00 00 00 00 00 00
CHG: 19 0E 50 00 FF FF FF FF FF FF 00 00 00 00 00 00
DEF: 1A 26 00 06 00 00 00 01 00 00 23 28 00 00 04 B0 00 00 17 70 00 00 17 70 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 58
CHG: 1A 26 01 0F FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 FC
DEF: 1C 0A 10 00 00 00 00 00 00 00 00 01
CHG: 1C 0A 9D 0F FF FF FF FF FF FF FF FF
Seagate Enterprise Capacity 3.5 HDD v5 SAS Product Manual, Rev. E 53
Table 22 Mode Sense data changeable and default values for 2TB drives
Block Descriptor:
00 00 00 00 E8 E0 88 B0 00 00 00 00 00 00 02 00 (512n)
Mode Pages:
DEF: 00 0A 00 80 0F 00 00 00 00 00 00 00
CHG: 00 0A B7 C0 8F 00 00 00 00 00 FF FF
DEF: 01 0A C0 14 FF 00 00 00 05 00 FF FF
CHG: 01 0A FF FF 00 00 00 00 FF 00 FF FF
DEF: 02 0E 00 00 00 00 00 00 00 00 00 A0 00 00 00 00
CHG: 02 0E 00 00 FF FF 00 00 FF FF FF FF 00 00 00 00
DEF: 03 16 00 01 00 00 00 00 00 02 00 03 02 00 00 01 00 00 00 00 40 00 00 00
CHG: 03 16 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
DEF: 04 16 05 50 F5 04 00 00 00 00 00 00 00 00 00 00 00 00 00 00 1C 20 00 00
CHG: 04 16 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
DEF: 07 0A 00 14 FF 00 00 00 00 00 FF FF
CHG: 07 0A 0F FF 00 00 00 00 00 00 FF FF
DEF: 08 12 14 00 FF FF 00 00 FF FF FF FF 80 20 00 00 00 00 00 00
CHG: 08 12 A5 00 00 00 FF FF FF FF 00 00 20 00 00 00 00 00 00 00
DEF: 0A 0A 02 00 00 80 00 00 00 00 2A 30
CHG: 0A 0A 0F F6 00 00 00 00 00 00 00 00
DEF: 18 06 06 00 00 00 00 00
CHG: 18 06 00 00 00 00 00 00
DEF: 19 0E 46 00 07 D0 00 00 00 00 00 00 00 00 00 00
CHG: 19 0E 50 00 FF FF FF FF FF FF 00 00 00 00 00 00
DEF: 1A 26 00 06 00 00 00 01 00 00 23 28 00 00 04 B0 00 00 17 70 00 00 17 70 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 58
CHG: 1A 26 01 0F FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 FC
DEF: 1C 0A 10 00 00 00 00 00 00 00 00 01
CHG: 1C 0A 9D 0F FF FF FF FF FF FF FF FF
Seagate Enterprise Capacity 3.5 HDD v5 SAS Product Manual, Rev. E 54
Table 23 Mode Sense data changeable and default values for 1TB drives
Block Descriptor:
00 00 00 00 74 70 6D B0 00 00 00 00 00 00 02 00 (512n)
Mode Pages:
DEF: 00 0A 00 80 0F 00 00 00 00 00 00 00
CHG: 00 0A B7 C0 8F 00 00 00 00 00 FF FF
DEF: 01 0A C0 14 FF 00 00 00 05 00 FF FF
CHG: 01 0A FF FF 00 00 00 00 FF 00 FF FF
DEF: 02 0E 00 00 00 00 00 00 00 00 00 A0 00 00 00 00
CHG: 02 0E 00 00 FF FF 00 00 FF FF FF FF 00 00 00 00
DEF: 03 16 00 01 00 00 00 00 00 02 00 03 02 00 00 01 00 00 00 00 40 00 00 00
CHG: 03 16 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
DEF: 04 16 05 DF F9 02 00 00 00 00 00 00 00 00 00 00 00 00 00 00 1C 20 00 00
CHG: 04 16 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
DEF: 07 0A 00 14 FF 00 00 00 00 00 FF FF
CHG: 07 0A 0F FF 00 00 00 00 00 00 FF FF
DEF: 08 12 14 00 FF FF 00 00 FF FF FF FF 80 20 00 00 00 00 00 00
CHG: 08 12 A5 00 00 00 FF FF FF FF 00 00 20 00 00 00 00 00 00 00
DEF: 0A 0A 02 00 00 80 00 00 00 00 FF FF
CHG: 0A 0A 0F F6 00 00 00 00 00 00 00 00
DEF: 18 06 06 00 00 00 00 00
CHG: 18 06 00 00 00 00 00 00
DEF: 19 0E 46 00 07 D0 00 00 00 00 00 00 00 00 00 00
CHG: 19 0E 50 00 FF FF FF FF FF FF 00 00 00 00 00 00
DEF: 1A 26 00 06 00 00 00 01 00 00 23 28 00 00 04 B0 00 00 17 70 00 00 17 70 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 58
CHG: 1A 26 01 0F FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 FC
DEF: 1C 0A 10 00 00 00 00 00 00 00 00 01
CHG: 1C 0A 9D 0F FF FF FF FF FF FF FF FF
Seagate Enterprise Capacity 3.5 HDD v5 SAS Product Manual, Rev. E 55
11.4 Miscellaneous operating features and conditions
Table 24 lists various features and conditions. A “Y” in the support column indicates the feature or condition is supported. An “N” in the support
column indicates the feature or condition is not supported.
11.4.1 SAS physical interface
Figure 12 shows the location of the SAS device connector J1. Figures 13 and 14 provide the dimensions of the SAS connector.
Details of the physical, electrical, and logical characteristics are provided within this section. The operational aspects of Seagate’s SAS drives are
provided in the SAS Interface Manual.
Figure 12. Physical interface
Table 24 Miscellaneous features
Supported Feature or condition
N Automatic contingent allegiance
N Asynchronous event notification
N Synchronized (locked) spindle operation
Y Segmented caching
N Zero latency read
Y Queue tagging (up to 64 queue tags supported)
Y Deferred error handling
Y Parameter rounding (controlled by Round bit in Mode Select page 0)
Y Reporting actual retry count in Extended Sense bytes 15, 16, and 17
N Adaptive caching
Y SMP = 1 in Mode Select command needed to save RPL and rotational offset bytes
Table 25 Miscellaneous status
Supported Status
YGood
Y Check condition
Y Condition met/good
YBusy
YIntermediate/good
Y Intermediate/condition met/good
Y Reservation conflict
YTask set full
NACA active
N ACA active, faulted initiator
Seagate Enterprise Capacity 3.5 HDD v5 SAS Product Manual, Rev. E 56
Figure 13. SAS device plug dimensions
C OF DATUM B
L
5.08
1.27 (6X)
1.27 (14X)
15.875
0.35MIN
15.875
33.43 0.05 B
4.90 0.08
0.84 0.05 (22X)
0.15 B
P15 P1
S7
S1
SEE Detail1
0.30 0.05 (4X)
4.00 0.08
0.15 D
0.30 0.05 (2X)
41.13 0.15
B
BC
CA
A
0.20 B
42.73 REF.
C OF DATUM D
L
1.10
R0.30 0.08 (4X)
2.00 (3X)
5.08
0.45 0.03 (7X)
0.10 M E
4.65
0.80 (6X)
7.625.92
0.52 0.08 x 45
Seagate Enterprise Capacity 3.5 HDD v5 SAS Product Manual, Rev. E 57
Figure 14. SAS device plug dimensions (detail)
6.10
Detail A
0.30 0.05 x 45 (5X)
0.40 0.05 X 45 (3X)
CORING ALLOWED
IN THIS AREA.
2.25 0.05
4.85 0.05
0.10 B
E
S14 S8
4.40 0.15
SEE Detail 2
3.90 0.15
SECTION A - A
SECTION C - C
A
0.35 0.05
45
R0.30 0.08 C
1.95 0.08
0.08 0.05
1.23 0.05
0.08 0.05
Detail 2
CONTACT SURFACE FLUSH
TO DATUM A 0.03
65
30
1.90 0.08
SECTION B - B
2.40 0.08
0.10 A
D
Seagate Enterprise Capacity 3.5 HDD v5 SAS Product Manual, Rev. E 58
11.4.2 Physical characteristics
This section defines physical interface connector.
11.4.3 Connector requirements
Contact the preferred connector manufacturer for mating part information. Part numbers for SAS connectors will be provided in a future revision of
this publication when production parts are available from major connector manufacturers.
The SAS device connector is illustrated in Figures 13 and 14.
11.4.4 Electrical description
SAS drives use the device connector for:
• DC power
• SAS interface
• Activity LED
This connector is designed to either plug directly into a backpanel or accept cables.
11.4.5 Pin descriptions
This section provides a pin-out of the SAS device and a description of the functions provided by the pins.
Table 26 SAS pin descriptions
* - Short pin to support hot plugging
** - Power Disable (T10 Industry Standard) for remote management of the end device. Allows power cycling / power saving to be controlled by the
host via interface pin 3.
NC - No connection in the drive.
Pin Signal name Signal type Pin Signal name Signal type
S1 Port A Ground P1* NC (reserved 3.3Volts)
S2* +Port A_in Diff. input pair P2* NC (reserved 3.3Volts)
S3* -Port A_in P3 SAS Power Disable **
S4 Port A Ground P4 Ground
S5* -Port A_out Diff output pair P5 Ground
S6* +Port A_out P6 Ground
S7 Port A Ground P7 5 Volts charge
S8 Port B Ground P8* 5 Volts
S9* +Port B_in Diff. input pair P9* 5 Volts
S10* -Port B_in P10 Ground
S11 Port A Ground P11* Ready LED Open collector out
S12* -Port B_out Diff output pair P12 Ground
S13* +Port B_out P13 12 Volts charge
S14 Port B Ground P14* 12 Volts
P15* 12 Volts
Seagate Enterprise Capacity 3.5 HDD v5 SAS Product Manual, Rev. E 59
11.4.6 SAS transmitters and receivers
A typical SAS differential copper transmitter and receiver pair is shown in Figure 15. The receiver is AC coupling to eliminate ground shift noise.
Figure 15. SAS transmitters and receivers
11.4.7 Power
The drive receives power (+5 volts and +12 volts) through the SAS device connector.
Three +12 volt pins provide power to the drive, 2 short and 1 long. The current return for the +12 volt power supply is through the common ground
pins. The supply current and return current must be distributed as evenly as possible among the pins.
Three +5 volt pins provide power to the drive, 2 short and 1 long. The current return for the +5 volt power supply is through the common ground
pins. The supply current and return current must be distributed as evenly as possible among the pins.
Current to the drive through the long power pins may be limited by the system to reduce inrush current to the drive during hot plugging.
11.5 Signal characteristics
This section describes the electrical signal characteristics of the drive’s input and output signals. See Table 26 for signal type and signal name
information.
11.5.1 Ready LED Out
The Ready LED Out signal is driven by the drive as indicated in Table 27.
The Ready LED Out signal is designed to pull down the cathode of an LED. The anode is attached to the proper +3.3 volt supply through an
appropriate current limiting resistor. The LED and the current limiting resistor are external to the drive. See Table 28 for the output characteristics of
the LED drive signals.
Table 27 Ready LED Out conditions
Normal command activity LED status
Ready LED Meaning bit mode page 19h 01
Spun down and no activity Off Off
Spun down and activity (command executing) On On
Spun up and no activity On Off
Spun up and activity (command executing) Off On
Spinning up or down Blinks steadily
(50% on and 50% off, 0.5 seconds on and off for 0.5 seconds)
Format in progress, each cylinder change Toggles on/off
Receiver
Differential
Transfer Medium
.01
.01
100100
Transmitter
RX
RY
TX
TY
Seagate Enterprise Capacity 3.5 HDD v5 SAS Product Manual, Rev. E 60
11.5.2 Differential signals
The drive SAS differential signals comply with the intra-enclosure (internal connector) requirements of the SAS standard.
Table 29 defines the general interface characteristics.
11.6 SAS-3 Specification Compliance
Seagate SAS-3 compatible drives are compliant with the latest SAS-3 Specification (T10/BSR INCITS 519 rev. 06).
The main difference from SAS-2 is the Tx and Rx training that allows the host and drive to adjust the amplitude and emphasis values to the channel.
The receiver still employs Decision Feedback Equalizer (DFE) and Feed Forward Equalizer (FFE) circuitry to accomplish this training.
1. A Decision Feedback Equalizer (DFE) which utilizes the standard SAS-2 training pattern transmitted during the SNW-3 training gap. The DFE cir-
cuit can derive an optimal equalization characteristic to compensate for many of the receive losses in the system.
2. A Feed Forward Equalizer (FFE) optimized to provide balanced receive margins over a range of channels bounded by the best and worst case
channels as defined by the relevant ANSI standard.
11.7 Additional information
Please contact the Seagate representative for SAS electrical details, if required.
For more information about the Phy, Link, Transport, and Applications layers of the SAS interface, refer to the Seagate SAS Interface Manual, part
number 100293071.
For more information about the SCSI commands used by Seagate SAS drives, refer to the Seagate SCSI Commands Reference Manual, part number
100293068.
Table 28 LED drive signal
State Test condition Output voltage
LED off, high 0 V ≤ VOH ≤ 3.6 V -100 μA < IOH < 100 μA
LED on, low IOL = 15 mA 0 ≤ VOL ≤ 0.225 V
Table 29 General interface characteristics
Characteristic Units 1.5Gb/s 3.0Gb/s 6.0Gb/s 12 Gbps
Bit rate (nominal) Mbaud 1,500 3,000 6,000 12000
Unit interval (UI)(nominal) ps 666.6 333.3 166.6 83.3
Impedance (nominal, differential ) ohm 100 100 100 100
Transmitter transients, maximum V ± 1.2 ± 1.2 ± 1.2 ± 1.2
Receiver transients, maximum V ± 1.2 ± 1.2 ± 1.2 ± 1.2
Seagate Technology LLC
AMERICAS Seagate Technology LLC 10200 South De Anza Boulevard, Cupertino, California 95014, United States, 408-658-1000
ASIA/PACIFIC Seagate Singapore International Headquarters Pte. Ltd. 7000 Ang Mo Kio Avenue 5, Singapore 569877, 65-6485-3888
EUROPE, MIDDLE EAST AND AFRICA Seagate Technology SAS 16-18 rue du Dôme, 92100 Boulogne-Billancourt, France, 33 1-4186 10 00
Publication Number: 100793635, Rev. E
June 2017