Table of Contents
- SATA Product Manual
- Seagate® Technology Support Services
- 1.0 Introduction
- 2.0 Drive Specifications
- 2.1 Specification summary tables
- 2.2 Formatted capacity
- 2.3 Default logical geometry
- 2.4 Start/stop times
- 2.5 Power specifications
- 2.6 Environmental limits
- 2.7 Acoustics
- 2.8 Electromagnetic immunity
- 2.9 Reliability
- 2.10 HDD and SSD Regulatory Compliance and Safety
- 2.11 Corrosive environment
- 2.12 Reference documents
- 2.13 Product warranty
- 2.14 Seagate® Rescue™ Data Recovery Service
- 3.0 Configuring and Mounting the Drive
- 4.0 SATA Interface
Seagate ST4000VN006 User Manual
Displayed below is the user manual for ST4000VN006 by Seagate which is a product in the Internal Hard Drives category. This manual has pages.
Related Manuals
100807039, Rev. P
January 2022
Standard models
ST8000VN002
ST6000VN001
ST6000VN006
ST4000VN006
ST4000VN008
Standard models
ST3000VN006
ST3000VN007
ST2000VN003
ST2000VN004
ST1000VN002
SATA Product Manual
© 2022, Seagate Technology LLC All rights reserved.
Publication number: 100807039, Rev. P January 2022
Seagate, Seagate Technology and the Spiral logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries. IronWolf and SeaTools are either trade-
marks or registered trademarks of Seagate Technology LLC or one of its affiliated companies in the United States and/or other countries.
No part of this publication may be reproduced in any form without written permission of Seagate Technology LLC.
Call 877-PUB-TEK1 (877-782-8351) to request permission.
When referring to drive capacity, one gigabyte, or GB, equals one billion bytes and one terabyte, or TB, equals one trillion bytes. Your computer’s operating system may use a different
standard of measurement and report a lower capacity. In addition, some of the listed capacity is used for formatting and other functions, and thus will not be available for data storage.
Actual quantities will vary based on various factors, including file size, file format, features and application software. Actual data rates may vary depending on operating environment and
other factors. Seagate reserves the right to change, without notice, product offerings or specifications.
Document Revision History
Revision Date Pages affected and Description of Change
Rev. P 01-06-2022 1: Updated legal disclaimer.
8: Updated Sustained Data Transfer Rate to 202 MB/s
Seagate IronWolf Product Manual, Rev. P 2
Contents
Seagate® Technology Support Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.0 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.1 About the SATA interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.0 Drive Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.1 Specification summary tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.2 Formatted capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.2.1 LBA mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.3 Default logical geometry. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.4 Start/stop times . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.5 Power specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.5.1 Power consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.5.2 Conducted noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.5.3 Voltage tolerance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.5.4 Power-management modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.6 Environmental limits. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.6.1 Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.6.2 Humidity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.6.3 Altitude . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.6.4 Shock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2.6.5 Vibration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2.7 Acoustics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2.7.1 Test for Prominent Discrete Tones (PDTs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2.8 Electromagnetic immunity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2.9 Reliability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
2.9.1 Annualized Failure Rate (AFR) and Mean Time Between Failures (MTBF) . . . . . . . . . . . . . 20
2.10 HDD and SSD Regulatory Compliance and Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
2.10.1 Regulatory models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
2.11 Corrosive environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
2.12 Reference documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
2.13 Product warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
2.14 Seagate® Rescue™ Data Recovery Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Seagate IronWolf Product Manual, Rev. P 3
Contents
3.0 Configuring and Mounting the Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
3.1 Handling and static-discharge precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
3.2 Configuring the drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
3.3 SATA cables and connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
3.4 Drive mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
4.0 SATA Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
4.1 Hot-Plug compatibility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
4.2 SATA device plug connector pin definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
4.3 Supported ATA commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
4.3.1 Identify Device command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
4.3.2 Set Features command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
4.3.3 S.M.A.R.T. commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Seagate IronWolf Product Manual, Rev. P 4
Figures
Figure 1 Typical 12V startup and operation current profile (4-disk models) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Figure 2 Typical 12V startup and operation current profile (1 and 2-disk models) . . . . . . . . . . . . . . . . . . . . . . . . . 15
Figure 3 Attaching SATA cabling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Figure 4 Mounting dimensions (ST4000VN006, ST3000VN006, ST2000VN003 and ST1000VN002 models) . 25
Figure 5 Mounting dimensions (ST2000VN004 model). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Figure 6 Mounting dimensions (ST6000VN001 model). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Figure 7 Mounting dimensions (ST8000VN002, ST6000VN006, ST4000VN008 and ST3000VN007 models) . 28
Seagate IronWolf Product Manual, Rev. P 5
For Seagate Product Support, visit: www.seagate.com/support
For Seagate Compliance, Safety, and Disposal, visit: www.seagate.com/support
For Firmware Download and Tools Download for Secure Erase, visit: www.seagate.com/support/downloads/
For information regarding online support and services, visit: www.seagate.com/contacts/
For information regarding Warranty Support, visit: www.seagate.com/support/warranty-and-replacements/
For information regarding data recovery services, visit: www.seagate.com/services-software/recover/resources/
For Seagate OEM and Distribution partner and Seagate reseller portal, visit: www.seagate.com/partners
Seagate® Technology Support Services
Seagate IronWolf Product Manual, Rev. P 6
1.0 Introduction
This manual describes the functional, mechanical and interface specifications for the following: Seagate® IronWolfTM model drives
These drives provide the following key features:
• 24x7 capability
• Balance technology to support multiple drives in a system
• Compliant with RoHS requirements in China and Europe
• Full-track multiple-sector transfer capability without local processor intervention
• Low activity and idle power
• Native Command Queuing with command ordering to increase performance in demanding applications
• Off-the-shelf compatibility
• Performance-tuned for RAID applications
•Rated for 1M hours MTBF
• SeaTools diagnostic software performs a drive self-test that eliminates unnecessary drive returns.
• State-of-the-art cache and on-the-fly error-correction algorithms
• Streaming video optimization - consistent command completion times & ERC support
• Support for S.M.A.R.T. drive monitoring and reporting
• Supports ATA8 streaming commands
• Supports latching SATA cables and connectors
• Worldwide Name (WWN) capability uniquely identifies the drive
ST8000VN002 ST6000VN006 ST4000VN008 ST3000VN007 ST2000VN004
ST6000VN001 ST4000VN006 ST3000VN006 ST2000VN003 ST1000VN002
Seagate IronWolf Product Manual, Rev. P 7
www.seagate.com Introduction
1.1 About the SATA interface
The Serial ATA (SATA) interface provides several advantages over the traditional (parallel) ATA interface. The primary advantages
include:
• Easy installation and configuration with true plug-and-play connectivity. It is not necessary to set any jumpers or other
configuration options.
• Thinner and more flexible cabling for improved enclosure airflow and ease of installation.
• Scalability to higher performance levels.
In addition, SATA makes the transition from parallel ATA easy by providing legacy software support. SATA was designed to allow
users to install a SATA host adapter and SATA disk drive in the current system and expect all of the existing applications to work as
normal.
The SATA interface connects each disk drive in a point-to-point configuration with the SATA host adapter. There is no master/slave
relationship with SATA devices like there is with parallel ATA. If two drives are attached on one SATA host adapter, the host
operating system views the two devices as if they were both “masters” on two separate ports. This essentially means both drives
behave as if they are Device 0 (master) devices.
The SATA host adapter and drive share the function of emulating parallel ATA device behavior to provide backward compatibility
with existing host systems and software. The Command and Control Block registers, PIO and DMA data transfers, resets, and
interrupts are all emulated.
The SATA host adapter contains a set of registers that shadow the contents of the traditional device registers, referred to as the
Shadow Register Block. All SATA devices behave like Device 0 devices. For additional information about how SATA emulates parallel
ATA, refer to the “Serial ATA International Organization: Serial ATA Revision 3.2”. The specification can be downloaded from
www.sata-io.org.
Note
The host adapter may, optionally, emulate a master/slave environment to host software where two
devices on separate SATA ports are represented to host software as a Device 0 (master) and Device 1
(slave) accessed at the same set of host bus addresses. A host adapter that emulates a master/slave
environment manages two sets of shadow registers. This is not a typical SATA environment.
Seagate IronWolf Product Manual, Rev. P 8
2.0 Drive Specifications
Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience,
the phrases the drive and this drive are used throughout this manual to indicate the following drive models:
2.1 Specification summary tables
The specifications listed in Table 1 are for quick reference. For details on specification measurement or definition, refer to the
appropriate section of this manual.
ST8000VN002 ST6000VN006 ST4000VN008 ST3000VN007 ST2000VN004
ST6000VN001 ST4000VN006 ST3000VN006 ST2000VN003 ST1000VN002
Table 1 Drive specifications summary
Drive Specification* ST8000VN002 ST6000VN006 ST6000VN001 ST4000VN006 ST3000VN006
Formatted capacity (512 bytes/sector)** 8000GB (8TB) 6000GB (6TB) 4000GB (4TB) 3000GB (3TB)
Guaranteed sectors 15,628,053,168 11,721,045,168 7,814,037,168 5,860,533,168
Heads 8 4
Disks 4 2
Bytes per sector (4K physical emulated
at 512-byte sectors) 4096
Default sectors per track 63
Default read/write heads 16
Default cylinders 16,383
Recording density (max) (KBPI) 2448 1984 2448
Track density (avg) (KTPI) 480 370 480
Areal density (avg) (Gb/in2) 1175 732 1175
SATA interface transfer rate 600MB/s
Maximum sustained data rate 202 MB/s
ATA data-transfer modes supported
PIO modes: 0 to 4
Multiword DMA modes: 0 to 2
Ultra DMA modes 0 to 6
Cache buffer 256MB
Height (max) 26.11mm / 1.028 in 20.20mm / 0.795 in (max)
Width (max) 101.85mm / 4.010 in
Length (max) 146.99mm / 5.787 in
Weight (max) 630g / 1.389 lb 610g / 1.345 lb 490g / 1.08 lb
Average latency 6.0 ms 4.0ms 6.0 ms
Startup current (typical) 12V 1.8A
Voltage tolerance (including noise) 5V: ±5%
12V: ±10%
Non-Operating (Ambient °C) -40 to 70
Operating ambient temperature
(min °C) #0°
Operating temperature
(drive reported max °C) 65°†
Temperature gradient 20°C per hour max (operating)
30°C per hour max (nonoperating)
Relative humidity 5% to 90% (operating)
5% to 95% (nonoperating)
Relative humidity gradient (max) 30% per hour
Seagate IronWolf Product Manual, Rev. P 9
www.seagate.com Drive Specifications
The following table footnotes apply to Table 1 and Table 2:
* All specifications above are based on native configurations.
** One GB equals one billion bytes and 1TB equals one trillion bytes when referring to hard drive capacity.
Accessible capacity may vary depending on operating environment and formatting.
*** During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification,
which may increase acoustic and power to operational levels.
†Seagate does not recommend operating at sustained drive temperatures above 60°C.
Operating at higher temperatures may affect drive health.
# The operating temperature is 0 to 65°C (32 to 149°F).
Altitude, operating –304m to 3048m
(–1000 ft to 10,000 ft)
Altitude, non-operating
(below mean sea level, max)
–304m to12,192m
(–1000ft to 40,000+ ft)
Operational Shock (@ 2ms, max) 80 Gs (read) / 70 Gs (write) 70 Gs 80 Gs
Non-Operational Shock (@ 2ms, max) 300 Gs 250 Gs 300 Gs
Vibration, operating
10Hz to 22Hz: 0.25 Gs, Limited displacement
22Hz to 350Hz: 0.50 Gs
350Hz to 500Hz: 0.25 Gs
Vibration, non-operating
5Hz to 22Hz: 3.0 Gs
22Hz to 350Hz: 3.0 Gs
350Hz to 500Hz: 3.0 Gs
Drive acoustics, sound power
Idle*** 2.7 bels (typical)
2.8 bels (max)
2.3 bels (typical)
2.4 bels (max)
Seek 2.8 bels (typical)
2.9 bels (max)
2.7 bels (typical)
2.8 bels (max)
Non-recoverable read errors 1 per 1014 bits read 1 per 10 15
bits read 1 per 1014 bits read
Annualized Failure Rate (AFR)*0.87% based on 8760 POH
Rated Workload
Maximum rate of <180TB/year
Workloads exceeding the annualized rate may degrade the drive MTBF and impact product reli-
ability. The Annualized Workload Rate is in units of TB per year, or TB per 8760 power on hours.
Workload Rate = TB transferred * (8760 / recorded power on hours).
Warranty
To determine the warranty for a specific drive, use a web browser to access the following web
page: www.seagate.com/support/warranty-and-replacements/.
From this page, click on the “Is my Drive under Warranty” link. The following are required to be
provided: the drive serial number, model number (or part number) and country of purchase.The
system will display the warranty information for the drive.
Load/Unload cycles
(command controlled) 600,000
Supports Hotplug operation per the
Serial ATA Revision 3.2 specification Yes
Note If the drive is powered-off before issuing flush cache command, in some instances,
the end user data in the DRAM cache might not be committed to the disk.
Table 1 Drive specifications summary
Drive Specification* ST8000VN002 ST6000VN006 ST6000VN001 ST4000VN006 ST3000VN006
Seagate IronWolf Product Manual, Rev. P 10
www.seagate.com Drive Specifications
Table 2 Drive specifications summary for 4TB, 3TB and 2TB models
Drive Specification* ST4000VN008 ST3000VN007 ST2000VN004 ST2000VN003 ST1000VN002
Formatted capacity (512 bytes/sector)** 4000GB (4TB) 3000GB (3TB) 2000GB (2TB) 1000GB (1TB)
Guaranteed sectors 7,814,037,168 5,860,533,168 3,907,029,168 1,953,525,168
Heads 6 6/5 4 2
Disks 332 1
Bytes per sector (4K physical emulated
at 512-byte sectors) 4096
Default sectors per track 63
Default read/write heads 16
Default cylinders 16,383
Recording density (max) (KBPI) 2089 1740 2448 1807kFCI
Track density (avg) (KTPI) 388 346 480 352
Areal density (avg) (Gb/in2) 810 613 1175 625Gfc/in2
Maximum sustained data rate,
OD read (MiB/s) 172 (180MB/s)
ATA data-transfer modes supported
PIO modes: 0 to 4
Multiword DMA modes: 0 to 2
Ultra DMA modes 0 to 6
I/O data-transfer rate (max) 600MB/s
Cache buffer 64MB 256MB 64MB
Height (max) 26.11mm / 1.028 in 20.20mm / 0.795 in
Width (max) 101.85mm /4.010 in
Length (max) 146.99mm / 5.787 in
Weight (max) 635g / 1.345 lb 535g / 1.18 lb 415g / 0.915 lb
Average latency 5.1ms 6.0ms 5.1ms
Startup current (typical) 12V 1.8A 1.2A
Voltage tolerance (including noise) 5V: ±5%
12V: ±10%
Non-Operating (Ambient °C) -40 to 70
Operating ambient temperature
(min °C)*0°C (Ambient)
Operating temperature (max °C)*65°C (Drive Reported Temperature) †
Temperature gradient 20°C per hour max (operating)
30°C per hour max (nonoperating)
Relative humidity 5% to 90% (operating)
5% to 95% (nonoperating)
Relative humidity gradient (max) 30% per hour
Altitude, operating –304m to 3048m
(–1000 ft to 10,000 ft)
Altitude, non-operating
(below mean sea level, max)
–304m to12,192m
(–1000ft to 40,000+ ft)
Operational Shock (@ 2ms, max) 80 Gs 80 Gs (read)
70 Gs (write)
80 Gs
Non-Operational Shock (@ 2ms max) 300 Gs 350 Gs 300 Gs
Vibration, operating
10Hz to 22Hz: 0.25 Gs, Limited displacement
22Hz to 350Hz: 0.50 Gs
350Hz to 500Hz: 0.25 Gs
Seagate IronWolf Product Manual, Rev. P 11
www.seagate.com Drive Specifications
2.2 Formatted capacity
*One GB equals one billion bytes and 1TB equals one trillion bytes when referring to hard drive capacity. Accessible capacity may vary depending
on operating environment and formatting.
Vibration, non-operating
5Hz to 22Hz: 3.0 Gs
22Hz to 350Hz: 3.0 Gs
350Hz to 500Hz: 3.0 Gs
Drive acoustics, sound power
Idle*** 2.3 bels (typical)
2.4 bels (max)
1.9 bels (typical)
2.0 bels (max)
Seek 2.7 bels (typical)
2.8 bels (max)
2.1 bels (typical)
2.2 bels (max)
Non-recoverable read errors 1 per 10 14 bits read
Annualized Failure Rate (AFR)*0.87% based on 8760 POH
Rated Workload
Maximum rate of <180TB/year
Workloads exceeding the annualized rate may degrade the drive MTBF and impact product reli-
ability. The Annualized Workload Rate is in units of TB per year, or TB per 8760 power on hours.
Workload Rate = TB transferred * (8760 / recorded power on hours).
Warranty
To determine the warranty for a specific drive, use a web browser to access the following web
page: www.seagate.com/support/warranty-and-replacements/.
From this page, click on the “Is my Drive under Warranty” link. The following are required to be
provided: the drive serial number, model number (or part number) and country of purchase.The
system will display the warranty information for the drive.
Load/Unload cycles
(command controlled) 600,000 —
Contact start-stop cycles
(25°C, 50% rel. humidity) — 50,000
Supports Hotplug operation per the
Serial ATA Revision 3.2 specification Yes
Model Formatted capacity* Guaranteed sectors Bytes per sector
ST8000VN002 8000GB 15,628,053,168
4096
ST6000VN001, ST6000VN006 6000GB 11,721,045,168
ST4000VN006, ST4000VN008 4000GB 7,814,037,168
ST3000VN006, ST3000VN007 3000GB 5,860,533,168
ST2000VN003, ST2000VN004 2000GB 3,907,029, 168
ST1000VN002 1000GB 1,953,525,168
Table 2 Drive specifications summary for 4TB, 3TB and 2TB models (continued)
Drive Specification* ST4000VN008 ST3000VN007 ST2000VN004 ST2000VN003 ST1000VN002
Seagate IronWolf Product Manual, Rev. P 12
www.seagate.com Drive Specifications
2.2.1 LBA mode
When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1, where n is the number of
guaranteed sectors as defined above.
See Section 4.3.1, "Identify Device command" (words 60-61 and 100-103) for additional information about 48-bit addressing
support of drives with capacities over 137GB.
2.3 Default logical geometry
•Cylinders: 16,383
•Read/write heads: 16
•Sectors per track: 63
LBA mode
When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1, where n is the number of
guaranteed sectors as defined above.
2.4 Start/stop times
The start/stop times listed below are for all models.
Time-to-ready may be longer than normal if the drive power is removed without going through normal OS powerdown
procedures.
Models ST8000VN002,
ST6000VN006 ST6000VN001 ST4000VN006,
ST3000VN006
ST4000VN008, ST3000VN007,
ST2000VN004, ST1000VN002 ST2000VN003
Power-on to ready
(in seconds) 17 (typical)
/ 30 (max)
23 (typical)
/ 30 (max) 17 (typical) / 30 (max)
8 (typical
Standby to ready
(in seconds) 8 (typical
Ready to spindle
stop (in seconds) 12 (typical) 23 (max) 12 (typical) 10 (typical) / 11 (max) 10 (typical
Seagate IronWolf Product Manual, Rev. P 13
www.seagate.com Drive Specifications
2.5 Power specifications
The drive receives DC power (+5V or +12V) through a native SATA power connector. Refer to Figure 3 on page 24.
2.5.1 Power consumption
Power requirements for the drives are listed in Table 7. Typical power measurements are based on an average of drives tested,
under nominal conditions, using 5.0V and 12.0V input voltage at 25°C ambient temperature.
• Spinup power
Spinup power is measured from the time of power-on to the time that the drive spindle reaches operating speed.
• Read/write power and current
Read/write power is measured with the heads on track, based on a 16-sector write followed by a 32-ms delay, then a 16-sector
read followed by a 32-ms delay.
• Operating power and current
Operating power is measured using 40 percent random seeks, 40 percent read/write mode (1 write for each 10 reads) and 20
percent drive idle mode.
• Idle mode power
Idle mode power is measured with the drive up to speed, with servo electronics active and with the heads in a random track
location.
•Standby mode
During Standby mode, the drive accepts commands, but the drive is not spinning, and the servo and read/write electronics are
in power-down mode.
Table 3 DC power requirements for ST1000VN002 models
Power dissipation
(1-disk values shown) Avg (watts 25°C) Avg 5V typ amps Avg 12V typ amps
Spinup — — 1.2
Idle* † 2.502 0.152 0.145
Operating 3.676 0.385 0.145
Standby 0.58 0.096 0.0084
Sleep 0.58 0.096 0.0084
Table 4 DC power requirements for ST2000VN003 model
Power dissipation Avg (watts 25° C) Avg 5V typ amps Avg 12V typ amps
Spinup — — 1.8
Idle, Low Power 2.5 0.12 0.15
Operating Power 3.7 0.28 0.191
Standby 0.25 0.04 0.004
Sleep 0.25 0.04 0.004
Seagate IronWolf Product Manual, Rev. P 14
www.seagate.com Drive Specifications
* Idle1. During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification,
which may increase acoustic and power to operational levels.
†5W IDLE with DIPLM Enabled
Table 5 DC power requirements for ST2000VN004 models
Power dissipation
(2-disk values shown) Avg (watts 25°C) Avg 5V typ amps Avg 12V typ amps
Spinup — — 1.8
Idle* † 3.56 0.171 0.225
Operating 4.30 0.308 0.233
Standby 0.50 0.09 0.005
Sleep 0.50 0.09 0.005
Table 6 DC power requirements for ST3000VN006, ST3000VN007, ST4000VN006 & ST4000VN008 models
Power dissipation
(4-disk values shown) Avg (watts 25°C) Avg 5V typ amps Avg 12V typ amps
Spinup — — 1.8
Idle* † 3.96 0.12 0.28
Operating 4.85 0.29 0.283
Standby 0.51 0.09 0.005
Sleep 0.51 0.09 0.005
Table 7 DC power requirements for ST6000VN001 models
Power dissipation Avg (watts 25° C) Avg 5V typ amps Avg 12V typ amps
Spinup — — 1.8
Idle* † 7.60 0.191 0.553
Operating 8.80 0.23 0.54
Standby 0.60 0.09 0.01
Sleep 0.60 0.09 0.01
Table 8 DC power requirements for ST8000VN002 & ST6000VN006 models
Power dissipation Avg (watts 25° C) Avg 5V typ amps Avg 12V typ amps
Spinup — — 1.8
Idle, Low Power 3.4 0.10 0.242
Operating Power 5.3 0.28 0.325
Standby 0.25 0.04 0.004
Sleep 0.25 0.04 0.004
Seagate IronWolf Product Manual, Rev. P 16
www.seagate.com Drive Specifications
2.5.2 Conducted noise
Input noise ripple is measured at the host system power supply across an equivalent 80-ohm resistive load on the +12 volt line or
an equivalent 15-ohm resistive load on the +5 volt line.
• Using 12-volt power, the drive is expected to operate with a maximum of 120 mV peak-to-peak sine-wave injected noise at up to
10MHz.
• Using 5-volt power, the drive is expected to operate with a maximum of 100 mV peak-to-peak sine-wave injected noise at up to
10MHz.
2.5.3 Voltage tolerance
Voltage tolerance (including noise):
•5V ±5%
•12V ±10%
2.5.4 Power-management modes
The drive provides programmable power management to provide greater energy efficiency. In most systems, users can control
power management through the system setup program. The drive features the following power-management modes:
•Active mode
The drive is in Active mode during the read/write and seek operations.
•Idle mode
The buffer remains enabled, and the drive accepts all commands and returns to Active mode any time disk access is necessary.
•Standby mode
The drive enters Standby mode when the host sends a Standby Immediate command. If the host has set the standby timer, the
drive can also enter Standby mode automatically after the drive has been inactive for a specifiable length of time. The standby
timer delay is established using a Standby or Idle command. In Standby mode, the drive buffer is enabled, the heads are parked
and the spindle is at rest. The drive accepts all commands and returns to Active mode any time disk access is necessary.
• Sleep mode
The drive enters Sleep mode after receiving a Sleep command from the host. In Sleep mode, the drive buffer is disabled, the
heads are parked and the spindle is at rest. The drive leaves Sleep mode after it receives a Hard Reset or Soft Reset from the host.
After receiving a reset, the drive exits Sleep mode and enters Standby mode with all current translation parameters intact.
• Idle and Standby timers
Each time the drive performs an Active function (read, write or seek), the standby timer is reinitialized and begins counting
down from its specified delay times to zero. If the standby timer reaches zero before any drive activity is required, the drive
makes a transition to Standby mode. In both Idle and Standby mode, the drive accepts all commands and returns to Active
mode when disk access is necessary.
Note Equivalent resistance is calculated by dividing the nominal voltage by the typical RMS read/write current.
Power modes Heads Spindle Electronics
Active Tracking Rotating Full Power
Idle, Performance Tracking Rotating Full Power
Idle, Active Floating Rotating Partial Power
Idle, Low Power Parked Rotating Partial Power
Standby Parked Stopped Low Power
Sleep Parked Stopped Low Power
Seagate IronWolf Product Manual, Rev. P 17
www.seagate.com Drive Specifications
2.6 Environmental limits
Temperature and humidity values experienced by the drive must be such that condensation does not occur on any drive part.
Altitude and atmospheric pressure specifications are referenced to a standard day at 58.7°F (14.8°C).
2.6.1 Temperature
a. Operating
32°F to 149°F (0°C ambient to 65°C drive reported) temperature range with a maximum temperature gradient of 36°F (20°C) per
hour.
The maximum allowable drive reported temperature is 149°F (65°C).
Air flow may be required to achieve consistent nominal drive temperature values (see Section 2.6 ). To confirm that the required
cooling is provided for the electronics and HDA, place the drive in its final mechanical configuration, and perform random
write/read operations. After the temperatures stabilize, monitor the current drive temperature using the SMART temperature
attribute 194 or Device Statistics log 04h page 5.
b. Non-operating
–40° to 158°F (–40° to 70°C) package ambient with a maximum gradient of 36°F (20°C) per hour. This specification assumes that
the drive is packaged in the shipping container designed by Seagate for use with drive.
2.6.2 Humidity
2.6.2.1 Relative humidity
2.6.2.2 Wet bulb temperature
2.6.3 Altitude
Caution
To maintain optimal performance drives should be run at nominal drive temperatures and humidity.
Seagate does not recommend operating at sustained drive temperatures above 60°C.
Operating at higher temperatures may affect drive health.
See Section 2.9, "Reliability" for rated MTBF device operating condition requirements.
Operating 5% to 90% non-condensing (30% per hour max)
Nonoperating 5% to 95% non-condensing (30% per hour max)
Operating 30°C / 86°F (rated)
Non-operating 40°C / 104°F (rated)
Operating –304m to 3048m (–1000 ft. to 10,000 ft.)
Non-operating –304m to 12,192m (–1000 ft. to 40,000+ ft.)
Seagate IronWolf Product Manual, Rev. P 18
www.seagate.com Drive Specifications
2.6.4 Shock
All shock specifications assume that the drive is mounted securely with the input shock applied at the drive mounting screws.
Shock may be applied in the X, Y or Z axis.
2.6.4.1 Operating shock
ST8000VN002, ST6000VN006 and ST2000VN003 models
These drives comply with the performance levels specified in this document when subjected to a maximum operating shock of 80
Gs (read) / 70 Gs (write) based on half-sine shock pulses of 2ms during read operations. Shocks should not be repeated more than
two times per second.
4TB, 3TB, ST2000VN004 and 1TB models
These drives comply with the performance levels specified in this document when subjected to a maximum operating shock of 80
Gs based on half-sine shock pulses of 2ms during read operations. Shocks should not be repeated more than 2 times per second.
ST6000VN001 model
These drives comply with the performance levels specified in this document when subjected to a maximum operating shock of 70
Gs based on half-sine shock pulses of 2ms during read operations. Shocks should not be repeated more than 2 times per second.
2.6.4.2 Non-operating shock
ST8000VN002, ST6000VN006, 4TB, 3TB, ST2000VN004 and 1TB models
The non-operating shock level that the drive can experience without incurring physical damage or degradation in performance
when subsequently put into operation is 300 Gs based on a non-repetitive half-sine shock pulse of 2ms duration.
ST2000VN003 model
The non-operating shock level that the drive can experience without incurring physical damage or degradation in performance
when subsequently put into operation is 350 Gs based on a non-repetitive half-sine shock pulse of 2ms duration.
ST6000VN001 model
The non-operating shock level that the drive can experience without incurring physical damage or degradation in performance
when subsequently put into operation is 250 Gs based on a non-repetitive half-sine shock pulse of 2ms duration.
2.6.5 Vibration
All vibration specifications assume that the drive is mounted securely with the input vibration applied at the drive mounting
screws. Vibration may be applied in the X, Y or Z axis. Throughput may vary if improperly mounted.
2.6.5.1 Operating vibration
The maximum vibration levels that the drive may experience while meeting the performance standards specified in this document
are specified below.
2.6.5.2 Non-operating vibration
The maximum non-operating vibration levels that the drive may experience without incurring physical damage or degradation in
performance when subsequently put into operation are specified below.
10Hz to 22Hz 0.25 Gs (Limited displacement)
22Hz to 350Hz 0.50 Gs
350Hz to 500Hz 0.25 Gs
5Hz to 22Hz 3.0 Gs (Limited displacement)
22Hz to 350Hz 3.0 Gs
350Hz to 500Hz 3.0 Gs
Seagate IronWolf Product Manual, Rev. P 19
www.seagate.com Drive Specifications
2.7 Acoustics
Drive acoustics are measured as overall A-weighted acoustic sound power levels (no pure tones). All measurements are consistent
with ISO document 7779. Sound power measurements are taken under essentially free-field conditions over a reflecting plane. For
all tests, the drive is oriented with the cover facing upward.
*During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and power to operational levels.
2.7.1 Test for Prominent Discrete Tones (PDTs)
Seagate follows the ECMA-74 standards for measurement and identification of PDTs. An exception to this process is the use of the
absolute threshold of hearing. Seagate uses this threshold curve (originated in ISO 389-7) to discern tone audibility and to
compensate for the inaudible components of sound prior to computation of tone ratios according to Annex D of the ECMA-74
standards.
2.8 Electromagnetic immunity
When properly installed in a representative host system, the drive operates without errors or degradation in performance when
subjected to the radio frequency (RF) environments defined in Table 10.
Note
For seek mode tests, the drive is placed in seek mode only.
The number of seeks per second is defined by the following equation:
(Number of seeks per second = 0.4 / (average latency + average access time
Table 9 Fluid Dynamic Bearing (FDB) motor acoustics
Idle* Seek
8TB & 6TB models 2.7 bels (typical)
2.8 bels (max)
2.8 bels (typical)
2.9 bels (max)
4TB, 3TB & 2TB models 2.3 bels (typical)
2.4 bels (max)
2.7 bels (typical)
2.8 bels (max)
1TB models 1.9 bels (typ)
2.0 bels (max)
2.1 bels (typ)
2.2 bels (max)
Table 10 Radio frequency environments
Test Description Performance
level
Reference
standard
Electrostatic discharge Contact, HCP, VCP: ± 4 kV; Air: ± 8 kV B EN61000-4-2: 95
Radiated RF immunity 80MHz to 1,000MHz, 3 V/m,
80% AM with 1kHz sine
A EN61000-4-3: 96
Electrical fast transient ± 1 kV on AC mains, ± 0.5 kV on external I/O B EN61000-4-4: 95
Surge immunity ± 1 kV differential, ± 2 kV common,
AC mains
B EN61000-4-5: 95
Conducted RF immunity 150kHz to 80MHz, 3 Vrms, 80% AM with 1kHz sine A EN61000-4-6: 97
Voltage dips, interrupts 0% open, 5 seconds
0% short, 5 seconds
40%, 0.10 seconds
70%, 0.01 seconds
C
C
C
B
EN61000-4-11: 94
Seagate IronWolf Product Manual, Rev. P 20
2.9 Reliability
2.9.1 Annualized Failure Rate (AFR) and Mean Time Between Failures (MTBF)
The production disk drive shall achieve an annualized failure-rate of 0.87% (MTBF of 1.000,000 hours) over a 5 year service life when
used in Enterprise Storage field conditions as limited by the following:
• 8760 power-on hours per year.
• HDA temperature as reported by the drive <= 40°C
• Ambient wet bulb temp <= 26°C
• Typical workload
• The AFR (MTBF) is a population statistic not relevant to individual units
• ANSI/ISA S71.04-2013 G2 classification levels and dust contamination to ISO 14644-1 Class 8 standards (as measured at the
device)
The MTBF specification for the drive assumes the operating environment is designed to maintain nominal drive temperature and
humidity. Occasional excursions in operating conditions between the rated MTBF conditions and the maximum drive operating
conditions may occur without significant impact to the rated MTBF. However continual or sustained operation beyond the rated
MTBF conditions will degrade the drive MTBF and reduce product reliability.
2.10 HDD and SSD Regulatory Compliance and Safety
For the latest regulatory and compliance information see: www.seagate.com/support/ scroll down the page to the Compliance,
Safety and Disposal Guide link.
2.10.1 Regulatory models
The following regulatory model number represent all features and configurations within the series:
SKR007 = ST8000VN002 & ST6000VN006
STR00C = ST6000VN001
SKR006 = ST4000VN006, ST3000VN006 & ST2000VN003
SKR001 = ST4000VN008 & ST3000VN007
VIDEO35HDD = ST2000VN004
STR009 = ST1000VN002
2.11 Corrosive environment
Seagate electronic drive components pass accelerated corrosion testing equivalent to 10 years exposure to light industrial
environments containing sulfurous gases, chlorine and nitric oxide, classes G and H per ASTM B845. However, this accelerated
testing cannot duplicate every potential application environment. Users should use caution exposing any electronic components
to uncontrolled chemical pollutants and corrosive chemicals as electronic drive component reliability can be affected by the
installation environment. The silver, copper, nickel and gold films used in Seagate products are especially sensitive to the presence
of sulfide, chloride, and nitrate contaminants. Sulfur is found to be the most damaging. In addition, electronic components should
never be exposed to condensing water on the surface of the printed circuit board assembly (PCBA) or exposed to an ambient
relative humidity greater than 95%. Materials used in cabinet fabrication, such as vulcanized rubber, that can outgas corrosive
compounds should be minimized or eliminated. The useful life of any electronic equipment may be extended by replacing
materials near circuitry with sulfide-free alternatives.
Nonrecoverable read errors 1 per 1015 bits read, max
Load unload cycles
(command controlled) 600,000 cycles
Maximum Rated Workload
Maximum rate of <180TB/year
Workloads exceeding the annualized rate may degrade the drive MTBF and impact product
reliability. The Annualized Workload Rate is in units of TB per year, or TB per 8760 power on
hours. Workload Rate = TB transferred * (8760 / recorded power on hours).
Warranty
To determine the warranty for a specific drive, use a web browser to access the following web
page: www.seagate.com/support/warranty-and-replacements/.
From this page, click on the “Is my Drive under Warranty” link. The following are required to be
provided: the drive serial number, model number (or part number) and country of purchase.
The system will display the warranty information for the drive.
Preventive maintenance None required.
Seagate IronWolf Product Manual, Rev. P 21
www.seagate.com Drive Specifications
2.12 Reference documents
Supported standards
Serial ATA Revision 3.3 specification
ANSI Documents
SFF-8301 3.5” Drive Form Factor with Serial Connector
INCITS 522-2014 SCSI Protocol Layer-4 (SPL-4) Rev. 08
Specification for Acoustic Test Requirement and Procedures
Seagate part number: 30553-001
In case of conflict between this document and any referenced document, this document takes precedence.
2.13 Product warranty
Beginning on the date of shipment to the customer and continuing for the period specified in the purchase contract, Seagate
warrants that each product (including components and subassemblies) that fails to function properly under normal use due to
defect in materials or workmanship or due to nonconformance to the applicable specifications will be repaired or replaced, at
Seagate’s option and at no charge to the customer, if returned by customer at customer’s expense to Seagate’s designated facility in
accordance with Seagate’s warranty procedure. Seagate will pay for transporting the repair or replacement item to the customer.
For more detailed warranty information, refer to the standard terms and conditions of purchase for Seagate products on the
purchase documentation.
The remaining warranty for a particular drive can be determined by calling Seagate Customer Service at 1-800-468-3472. Users can
also determine remaining warranty using the Seagate web site (www.seagate.com). The drive serial number is required to
determine remaining warranty information.
Shipping
When transporting or shipping a drive, use only a Seagate-approved container. Keep the original box. Seagate approved containers
are easily identified by the Seagate Approved Package label. Shipping a drive in a non-approved container voids the drive warranty.
Seagate repair centers may refuse receipt of components improperly packaged or obviously damaged in transit. Contact the
authorized Seagate distributor to purchase additional boxes. Seagate recommends shipping by an air-ride carrier experienced in
handling computer equipment.
Storage
Maximum storage periods are 180 days within original unopened Seagate shipping package or 60 days unpackaged within the
defined non-operating limits (refer to environmental section in this manual). Storage can be extended to 1 year packaged or
unpackaged under optimal environmental conditions (25°C, <40% relative humidity non-condensing, and non-corrosive
environment). During any storage period the drive non-operational temperature, humidity, wet bulb, atmospheric conditions,
shock, vibration, magnetic and electrical field specifications should be followed.
Product repair and return information
Seagate customer service centers are the only facilities authorized to service Seagate drives. Seagate does not sanction any third-
party repair facilities. Any unauthorized repair or tampering with the factory seal voids the warranty.
Seagate IronWolf Product Manual, Rev. P 22
2.14 Seagate® Rescue™ Data Recovery Service
If you suffer a data loss event within the Seagate Rescue Data Recovery warranty period, and you are eligible to participate in and
submit a case under the Rescue program, contact SRS at (1-800-723-1183) in the US, or if you are calling from outside the US please
visit our website for numbers in your local and language: www.seagate.com/contacts/contact-numbers/.
In addition, you may visit rescueandreplace.seagate.com/contact.jsp to obtain information regarding how to contact a recovery expert
online or by telephone from your location. An SRS representative will review your case to confirm your eligibility, and to assess whether
your data may be recoverable by remote recovery services or whether you will need to send your device to SRS for in-lab servicing.
Rescue™ General Terms
These Rescue™ General Terms together with the Rescue™ FAQ’s make up the Rescue™ Program Terms. By submitting a case under the
Rescue™ program (“Program”) you agree to be bound by the Program Terms, including these General Terms and the FAQ. You must be
a legal resident of the US to participate in the Program.
Communications. All communications relating to your request will be available on our web site in your account and sent via e-mail to
the address you provide to us unless you request, in writing, to receive such communications via regular mail.
Personal Data. You must provide true, accurate and complete information about yourself as prompted by the request form, including,
without limitation, your name, address, e-mail address, and telephone number, as applicable (collectively, “Personal Data”). You must
maintain and promptly update your Personal Data. You acknowledge that we may send you important information and notices
regarding your requests by e-mail and that we shall have no liability associated with or arising from your failure to maintain accurate
Personal Data.
Capacity; Legal Rights; Indemnity. You represent to SRS that you are of the legal age of majority in your state or country of residence,
with the full capacity to agree to these Program Terms. You warrant that you are the legal owner or the authorized representative of the
legal owner of the device you submit to SRS (the “Device”) and data. You warrant that the data on the Device is legal and that you have
the unrestricted legal right to (a) give us remote access to the data, (b) have the data recovered and reproduced on a backup medium,
(c) receive the recovered data, and (d) agree to these Program Terms. You will defend and indemnify us (including our directors,
officers, employees, agents, delegates, and contractors) from any claims or actions relating to the Device or data, or your rights or lack
of rights thereto.
Confidentiality. We will protect the confidentiality of your data against unauthorized disclosure using the same degree of care as we
use to protect our own confidential information.
Disclaimer of Warranties, Representations and Guarantees. WE PROVIDE THE PROGRAM AND ANY SERVICES PROVIDED OR
ATTEMPTED HEREUNDER “AS IS,” WITH ALL FAULTS, AT YOUR SOLE RISK. WE DO NOT EXTEND ANY EXPRESS WARRANTIES,
REPRESENTATIONS, CONDITIONS OR GUARANTEES REGARDING OUR RESCUE SERVICES OR ANY RESULTS THEREOF. TO THE
MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW AND SUBJECT TO ANY STATUTORY WARRANTIES THAT CANNOT BE
EXCLUDED, WE EXPRESSLY DISCLAIM ALL IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OR CONDITION OF
MERCHANTABILITY, WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, OR WARRANTY OF ACCURACY OR COMPLETENESS
WITH RESPECT TO THIS PROGRAM AND SERVICES. This Program and Disclaimer is unrelated to, and does not affect any warranties
relating to your Device that we or the seller may have extended to you.
Limitation of Liability. WE WILL NOT BE LIABLE FOR ANY HARM CAUSED, UNLESS YOU PROVE THAT WE CAUSED SUCH HARM
INTENTIONALLY. WITHOUT LIMITING THE GENERALITY OF THE FOREGOING, WE WILL NOT BE LIABLE FOR THE CONDITION,
EXISTENCE, OR LOSS OF THE DATA YOU SEND US OR THE DATA WE RECOVER (IF ANY), ANY LOSS OF REVENUE OR LOSS OF
PROFITS, OR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES HOWEVER CAUSED. TO THE MAXIMUM
EXTENT PERMITTED BY APPLICABLE LAW, THIS LIMITATION SHALL APPLY TO ANY AND ALL DAMAGES, REGARDLESS OF THE
LEGAL THEORY ON WHICH THEY ARE ASSERTED (INCLUDING, WITHOUT LIMITATION, CONTRACT, BREACH OF CONTRACT, AND
TORT), AND REGARDLESS OF WHETHER WE HAVE BEEN ADVISED OF THE POSSIBILITY OF LOSS OR DAMAGES - UNLESS YOU
PROVE THAT SRS CAUSED DAMAGES TO YOU INTENTIONALLY. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW,
THE AMOUNT OF OUR LIABILITY WILL NOT EXCEED THE TOTAL PRICE YOU ACTUALLY PAY FOR THE DEVICE, THE ESSENTIAL
PURPOSE OF WHICH IS TO LIMIT OUR LIABILITY ARISING FROM OR RELATED TO THE PROGRAM AND ANY DATA RECOVERY
SERVICES. THIS ALLOCATION OF RISK IS REFLECTED IN THE PRICE CHARGED FOR THIS PROGRAM OR SERVICES, IF ANY. YOU
ACKNOWLEDGE THAT THE PRICE OF THIS PROGRAM WOULD BE MUCH GREATER IF WE UNDERTOOK MORE EXTENSIVE
LIABILITY. THIS PARAGRAPH WILL APPLY NOTWITHSTANDING ANY OTHER PROVISIONS IN THESE TERMS, OR THE FAILURE OF
ANY REMEDY.
Seagate IronWolf Product Manual, Rev. P 23
Compliance with Laws. You agree to comply with all such laws and regulations and all other applicable laws, statutes, ordinances and
regulations relating to the Program. You acknowledge that violations of these Program Terms could subject you to criminal or civil
penalties. The goods licensed or provided, or services provided, through the Program, which may include technology and software, are
subject to the customs and export control laws and regulations of the U.S. and may also be subject to the customs and export laws and
regulations of the country in which the products are manufactured or received. Further, under U.S. law, such goods may not be sold,
leased or otherwise transferred to restricted countries, or used by a restricted end-user or an end-user engaged in activities related to
weapons of mass destruction including, without limitation, activities related to designing, developing, producing or using nuclear
weapons, materials, or facilities, missiles or supporting missile projects, or chemical or biological weapons. You acknowledge you are
not a restricted end-user or involved in any of the restricted activities above, and that you will comply with and abide by these laws and
regulations. Seagate reserves the right to refuse service to or the return of any storage devices that have been determined to violate
these regulations.
Cancellation. You may cancel the Program at any time by contacting SRS at 1-800-SEAGATE (1-800-475-0143) in the US, or at such
other number available at services.seagate.com/contact.aspx, or you simply may refrain from submitting a request for Rescue services.
These Program Terms remain applicable to your and SRS’s rights and obligations with respect to any services requested by you under
this Program.
Assignment. You may not assign your rights or obligations under these Program Terms without SRS’ express written consent.
Dispute Resolution. The parties will attempt to resolve any dispute arising out of or related to these Program Terms or any data
recovery services requested or attempted hereunder through good faith negotiation. To the extent permitted by applicable law, if the
parties are unable to resolve the dispute through good faith negotiation, then the dispute will be submitted to final and binding
arbitration with the Judicial Arbitration and Mediation Services. Each party will bear its own costs in arbitration, provided that Seagate
reserves the right, in its discretion, to pre-pay certain fees you may incur in connection with the arbitration subject to refund if you do
not prevail. Both parties waive their rights to a jury trial. All proceedings will take place in Santa Clara County, California, USA. The
laws of the State of California will exclusively govern these Program Terms and our provision of any data recovery services, without
regard to California's conflicts of laws rules. You consent to the exclusive jurisdiction of the courts located in Santa Clara County,
California, USA.
Severability. If any provision of these Program Terms is held invalid, illegal or unenforceable, such provision shall be enforced to the
fullest extent permitted by applicable law and the validity, legality and enforceability of the remaining provisions shall not be affected
thereby.
Legal Effect. These Program Terms describe certain legal rights. You may have other rights under applicable law. These Program Terms
do not change your rights under applicable law if such laws do not permit these Program Terms to do so. Also, the Program and these
Program Terms are in addition and unrelated to any rights you may have under a Seagate warranty statement.
SRS Companies. The following SRS companies may provide the services described in these Program Terms: (a) Seagate Technology
LLC, with offices at 3101 Jay Street, Suite 110, Santa Clara, California 95054; (b) Seagate Technology Canada Inc., with offices at 2421
Bristol Circle, Suite A100, Oakville, Ontario, Canada L6H 5S9; and/or (c) Seagate Technology (Netherlands) B.V., with offices at
Koolhovenlaan 1, 1119 PA, Schiphol-Rijk, The Netherlands.
Seagate IronWolf Product Manual, Rev. P 24
www.seagate.com Configuring and Mounting the Drive
3.0 Configuring and Mounting the Drive
This section contains the specifications and instructions for configuring and mounting the drive.
3.1 Handling and static-discharge precautions
After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic discharge (ESD) hazards.
Observe the following standard handling and static-discharge precautions:
Caution
• Before handling the drive, put on a grounded wrist strap, or ground oneself frequently by touching the metal chassis of a computer
that is plugged into a grounded outlet. Wear a grounded wrist strap throughout the entire installation procedure.
• Handle the drive by its edges or frame only.
• The drive is extremely fragile—handle it with care. Do not press down on the drive top cover.
• Always rest the drive on a padded, antistatic surface until mounting it in the computer.
• Do not touch the connector pins or the printed circuit board.
• Do not remove the factory-installed labels from the drive or cover them with additional labels. Removal voids the warranty. Some
factory-installed labels contain information needed to service the drive. Other labels are used to seal out dirt and contamination.
3.2 Configuring the drive
Each drive on the SATA interface connects point-to-point with the SATA host adapter. There is no master/slave relationship because
each drive is considered a master in a point-to-point relationship. If two drives are attached on one SATA host adapter, the host
operating system views the two devices as if they were both “masters” on two separate ports. Both drives behave as if they are
Device 0 (master) devices.
SATA drives are designed for easy installation. It is usually not necessary to set any jumpers on the drive for proper operation;
however, if users connect the drive and receive a “drive not detected” error, the SATA-equipped motherboard or host adapter may
use a chipset that does not support SATA speed autonegotiation.
3.3 SATA cables and connectors
The SATA interface cable consists of four conductors in two differential pairs, plus three ground connections. The cable size may be
30 to 26 AWG with a maximum length of one meter (39.37 inches). See Table 11 for connector pin definitions. Either end of the
SATA signal cable can be attached to the drive or host.
For direct backplane connection, the drive connectors are inserted directly into the host receptacle. The drive and the host
receptacle incorporate features that enable the direct connection to be hot pluggable and blind mateable.
For installations which require cables, users can connect the drive as illustrated in Figure 3.
Figure 3 Attaching SATA cabling
Each cable is keyed to ensure correct orientation. IronWolf drives support latching SATA connectors.
Seagate IronWolf Product Manual, Rev. P 25
www.seagate.com Configuring and Mounting the Drive
3.4 Drive mounting
Users can mount the drive in any orientation using four screws in the side-mounting holes or four screws in the bottom-mounting
holes. Refer to Figure 4 through Figure 7 for drive mounting dimensions. Follow these important mounting precautions when
mounting the drive:
• Allow a minimum clearance of 0.030 inches (0.76mm) around the entire perimeter of the drive for cooling.
• Use only 6-32 UNC mounting screws.
• The screws should be inserted no more than 0.140 inch (3.56mm) into the bottom or side mounting holes.
• Do not overtighten the mounting screws (maximum torque: 6 inch-lb).
Figure 4 Mounting dimensions (ST4000VN006, ST3000VN006, ST2000VN003 and ST1000VN002 models)
Max: .795" or 20.20 mm
Alterntive: .783" .012" or 19.90 0.30 mm
4X 6-32 UNC-2B
3 MINIMUM THREAD DEPTH
0.14 MAXIMUM FASTENER
PENETRATION
3X 6-32 UNC-2B
3 MINIMUM THREAD DEPTH
0.14 MAXIMUM FASTENER
PENETRATION BOTH SIDES
Seagate IronWolf Product Manual, Rev. P 26
www.seagate.com Configuring and Mounting the Drive
Figure 5 Mounting dimensions (ST2000VN004 model)
TOP OF LABEL
5 TYP
3X 6-32 UNC-2B
3 MINIMUM THREAD DEPTH
0.1 MAXIMUM FASTENER
PENETRATION BOTH SIDES
4X 6-32 UNC-2B
3 MINIMUM THREAD DEPTH
0.1 MAXIMUM FASTENER
PENETRATION
C
LOF DRIVE
C
L
OF CONNECTOR
DATUM B
5.787 in max
146.99 mm
4.010 in max
101.85 mm
2x 1.625 ± .020 in
41.28 ± .51 mm
2x 1.750 in
44.45 mm
2x 0.125 in
3.18 mm
4.00 in
101.60 mm
1.638 in
41.61 mm
1.122 ± .020 in
± .51 mm
0.138 in
3.51 mm
0.814 in
20.68 mm
1.028 in max
26.11 mm
3x 0.250 ± .010 in
6.35 ± .25 mm
BOTH SIDES
2x 3.750 in
95.25 mm
1.013 ± .050 in
25.73 ± 1.27 mm
0.680 ± .050 in
17.27 ± 1.27 mm
Temperature
Check Point
Seagate IronWolf Product Manual, Rev. P 28
www.seagate.com Configuring and Mounting the Drive
Figure 7 Mounting dimensions (ST8000VN002, ST6000VN006, ST4000VN008 and ST3000VN007 models)
4X 6-32 UNC-2B
3 MINIMUM THREAD DEPTH
0.14 MAXIMUM FASTENER
PENETRATION
3X 6-32 UNC-2B
3 MINIMUM THREAD DEPTH
0.14 MAXIMUM FASTENER
PENETRATION BOTH SIDES
Seagate IronWolf Product Manual, Rev. P 29
www.seagate.com SATA Interface
4.0 SATA Interface
These drives use the industry-standard Serial ATA (SATA) interface that supports FIS data transfers. It supports ATA programmed
input/output (PIO) modes 0 to 4; multiword DMA modes 0 to 2, and Ultra DMA modes 0 to 6.
For detailed information about the SATA interface, refer to the “Serial ATA: High Speed Serialized AT Attachment” specification.
4.1 Hot-Plug compatibility
IronWolf drives incorporate connectors which enable users to hot plug these drives in accordance with the SATA Revision 3.2
specification. This specification can be downloaded from www.serialata.org.
4.2 SATA device plug connector pin definitions
Table 11 summarizes the signals on the SATA interface and power connectors.
Notes
1. All pins are in a single row, with a 1.27 mm (0.050 in) pitch.
2. The comments on the mating sequence apply to the case of backplane blindmate connector only. In this case, the mating
sequences are:
• the ground pins P4 and P12.
• the pre-charge power pins and the other ground pins.
• the signal pins and the rest of the power pins.
3. There are three power pins for each voltage. One pin from each voltage is used for pre-charge when installed in a blind-mate
backplane configuration.
• All used voltage pins (Vx) must be terminated.
Table 11 SATA connector pin definitions
Segment Pin Function Definition
Signal S1 Ground 2nd mate
S2 A+ Differential signal pair A from Phy
S3 A-
S4 Ground 2nd mate
S5 B- Differential signal pair B from Phy
S6 B+
S7 Ground 2nd mate
Key and spacing separate signal and power segments
Power P1 V33 3.3V power
P2 V33 3.3V power
P3 V33 3.3V power, pre-charge, 2nd mate
P4 Ground 1st mate
P5 Ground 2nd mate
P6 Ground 2nd mate
P7 V55V power, pre-charge, 2nd mate
P8 V55V power
P9 V55V power
P10 Ground 2nd mate
P11 Ground or LED signal If grounded, drive does not use deferred spin
P12 Ground 1st mate.
P13 V12 12V power, pre-charge, 2nd mate
P14 V12 12V power
P15 V12 12V power
Seagate IronWolf Product Manual, Rev. P 30
www.seagate.com SATA Interface
4.3 Supported ATA commands
The following table lists SATA standard commands that the drive supports.
For a detailed description of the ATA commands, refer to the Serial ATA International Organization:
Serial ATA Revision 3.2 (www.sata-io.org).
See “S.M.A.R.T. commands” on page 37 for details and subcommands used in the S.M.A.R.T. implementation.
Table 12 SATA standard commands
Command name Command code (in hex)
Check Power Mode E5H
Device Configuration Freeze Lock B1H / C1H
Device Configuration Identify B1H / C2H
Device Configuration Restore B1H / C0H
Device Configuration Set B1H / C3H
Device Reset 08H
Download Microcode 92H
Execute Device Diagnostics 90H
Flush Cache E7H
Flush Cache Extended EAH
Format Track 50H
Identify Device ECH
Idle E3H
Idle Immediate E1H
Initialize Device Parameters 91H
Read Buffer E4H
Read DMA C8H
Read DMA Extended 25H
Read DMA Without Retries C9H
Read Log Ext 2FH
Read Multiple C4H
Read Multiple Extended 29H
Read Native Max Address F8H
Read Native Max Address Extended 27H
Read Sectors 20H
Read Sectors Extended 24H
Read Sectors Without Retries 21H
Read Verify Sectors 40H
Read Verify Sectors Extended 42H
Read Verify Sectors Without Retries 41H
Recalibrate 10H
Security Disable Password F6H
Security Erase Prepare F3H
Security Erase Unit F4H
Security Freeze F5H
Security Set Password F1H
Security Unlock F2H
Seek 70H
Seagate IronWolf Product Manual, Rev. P 31
www.seagate.com SATA Interface
Set Features EFH
Set Max Address F9H
Note: Individual Set Max Address
commands are identified by the value
placed in the Set Max Features register
as defined to the right.
Address:
Password:
Lock:
Unlock:
Freeze Lock:
00H
01H
02H
03H
04H
Set Max Address Extended 37H
Set Multiple Mode C6H
Sleep E6H
S.M.A.R.T. Disable Operations B0H / D9H
S.M.A.R.T. Enable/Disable Autosave B0H / D2H
S.M.A.R.T. Enable Operations B0H / D8H
S.M.A.R.T. Execute Offline B0H / D4H
S.M.A.R.T. Read Attribute Thresholds B0H / D1H
S.M.A.R.T. Read Data B0H / D0H
S.M.A.R.T. Read Log Sector B0H / D5H
S.M.A.R.T. Return Status B0H / DAH
S.M.A.R.T. Save Attribute Values B0H / D3H
S.M.A.R.T. Write Log Sector B0H / D6H
Standby E2H
Standby Immediate E0H
Write Buffer E8H
Write DMA CAH
Write DMA Extended 35H
Write DMA FUA Extended 3DH
Write DMA Without Retries CBH
Write Log Extended 3FH
Write Multiple C5H
Write Multiple Extended 39H
Write Multiple FUA Extended CEH
Write Sectors 30H
Write Sectors Without Retries 31H
Write Sectors Extended 34H
Write Uncorrectable 45H
Table 12 SATA standard commands (continued)
Command name Command code (in hex)
Seagate IronWolf Product Manual, Rev. P 32
www.seagate.com SATA Interface
4.3.1 Identify Device command
The Identify Device command (command code ECH) transfers information about the drive to the host following power up. The data
is organized as a single 512-byte block of data, whose contents are shown in Table 12 on page 30. All reserved bits or words
should be set to zero. Parameters listed with an “x” are drive-specific or vary with the state of the drive.
The following commands contain drive-specific features that may not be included in the SATA specification.
Table 13 Identify Device commands
Word Description Value
0
Configuration information:
• Bit 15: 0 = ATA; 1 = ATAPI
• Bit 7: removable media
• Bit 6: removable controller
• Bit 0: reserved
0C5AH
1 Number of logical cylinders 16,383
2 ATA-reserved 0000H
3 Number of logical heads 16
4 Retired 0000H
5 Retired 0000H
6 Number of logical sectors per logical track: 63 003FH
7–9 Retired 0000H
10–19 Serial number: (20 ASCII characters, 0000H = none) ASCII
20 Retired 0000H
21 Retired 0400H
22 Obsolete 0000H
23–26 Firmware revision (8 ASCII character string, padded with blanks to end of string) x.xx
27–46 Drive model number: (40 ASCII characters, padded with blanks to end of string)
47 (Bits 7–0) Maximum sectors per interrupt on Read multiple and Write multiple (16) 8010H
48 Reserved 0000H
49 Standard Standby timer, IORDY supported and may be disabled 2F00H
50 ATA-reserved 0000H
51 PIO data-transfer cycle timing mode 0200H
52 Retired 0200H
53 Words 54–58, 64–70 and 88 are valid 0007H
54 Number of current logical cylinders xxxxH
55 Number of current logical heads xxxxH
56 Number of current logical sectors per logical track xxxxH
57–58 Current capacity in sectors xxxxH
59 Number of sectors transferred during a Read Multiple or Write Multiple command xxxxH
Seagate IronWolf Product Manual, Rev. P 33
www.seagate.com SATA Interface
60–61
Total number of user-addressable LBA sectors available
(see Section 2.2 for related information)
*Note: The maximum value allowed in this field is: 0FFFFFFFh (268,435,455 sectors,
137GB). Drives with capacities over 137GB will have 0FFFFFFFh in this field and the
actual number of user-addressable LBAs specified in words 100-103. This is required
for drives that support the 48-bit addressing feature.
0FFFFFFFh*
62 Retired 0000H
63 Multiword DMA active and modes supported (see note following this table) xx07H
64 Advanced PIO modes supported (modes 3 and 4 supported) 0003H
65 Minimum multiword DMA transfer cycle time per word (120 nsec) 0078H
66 Recommended multiword DMA transfer cycle time per word (120 nsec) 0078H
67 Minimum PIO cycle time without IORDY flow control (240 nsec) 0078H
68 Minimum PIO cycle time with IORDY flow control (120 nsec) 0078H
69–74 ATA-reserved 0000H
75 Queue depth 001FH
76 SATA capabilities xxxxH
77 Reserved for future SATA definition xxxxH
78 SATA features supported xxxxH
79 SATA features enabled xxxxH
80 Major version number 01F0H
81 Minor version number 0028H
82 Command sets supported 364BH
83 Command sets supported 7F09H
84 Command sets support extension (see note following this table) 4163H
85 Command sets enabled 30xxH
86 Command sets enabled BE09H
87 Command sets enable extension 4163H
88 Ultra DMA support and current mode (see note following this table) xx7FH
89 Security erase time 0039H
90 Enhanced security erase time 0039H
92 Master password revision code FFFEH
93 Hardware reset value xxxxH
94 Automatic acoustic management 8080H
95 Stream Min. Request Size 0000H
96 Streaming Transfer Time - DMA 0000H
97 Streaming Access Latency - DMA and PIO 0000H
98–99 Streaming Performance Granularity 0000H
Table 13 Identify Device commands (continued)
Word Description Value
Seagate IronWolf Product Manual, Rev. P 34
www.seagate.com SATA Interface
100–103
Total number of user-addressable LBA sectors available
(see Section 2.2 for related information).
These words are required for drives that support the 48-bit addressing feature.
Maximum value: 0000FFFFFFFFFFFFh.
1TB model = 1,953,525,168
2TB models = 3,907,029,168
3TB models = 5,860,533,168
4TB models = 7,814,037,168
6TB models= 11,721,045,168
8TB models= 15,628,053,168
104 Streaming Transfer Time - PIO 0000H
105–107 ATA-reserved 0000H
108–111 The mandatory value of the world wide name (WWN) for the drive.
NOTE: This field is valid if word 84, bit 8 is set to 1 indicating 64-bit WWN support.
Each drive will have
a unique value.
112–127 ATA-reserved 0000H
128 Security status 0001H
129–159 Seagate-reserved xxxxH
160–167 ATA-reserved 0000H
168 Device Nominal Form Factor 0002H
169-205 ATA-reserved 0000H
206 SCT Command Transport 10A5H
207-208 ATA-reserved 0000H
209 Alignment of logical blocks within a physical block 4000H
210-216 ATA-reserved 0000H
217 Nominal media rotation rate 1518H
218-221 ATA-reserved 0000H
222 Transport major version number 107FH
223-229 ATA-reserved 0000H
230-233 Extended Number of User Addressable Sectors
1TB model = 1,953,525,168
2TB models = 3,907,029,168
3TB models = 5,860,533,168
4TB models = 7,814,037,168
6TB models= 11,721,045,168
8TB models= 15,628,053,168
234–254 ATA-reserved 0000H
255 Integrity word xxA5H
Note Advanced Power Management (APM) and Automatic Acoustic Management (AAM) features are not supported.
Note See the bit descriptions below for words 63, 84, and 88 of the Identify Drive data.
Table 13 Identify Device commands (continued)
Word Description Value
Seagate IronWolf Product Manual, Rev. P 35
www.seagate.com SATA Interface
Description (if bit is set to 1)
Bit Word 63
0 Multiword DMA mode 0 is supported.
1 Multiword DMA mode 1 is supported.
2 Multiword DMA mode 2 is supported.
8 Multiword DMA mode 0 is currently active.
9 Multiword DMA mode 1 is currently active.
10 Multiword DMA mode 2 is currently active.
Bit Word 84
0 SMART error login is supported.
1 SMART self-test is supported.
2 Media serial number is supported.
3 Media Card Pass Through Command feature set is supported.
4 Streaming feature set is supported.
5 GPL feature set is supported.
6 WRITE DMA FUA EXT and WRITE MULTIPLE FUA EXT commands are supported.
7 WRITE DMA QUEUED FUA EXT command is supported.
8 64-bit World Wide Name is supported.
9-10 Obsolete.
11-12 Reserved for TLC.
13 IDLE IMMEDIATE command with IUNLOAD feature is supported.
14 Shall be set to 1.
15 Shall be cleared to 0.
Bit Word 88
0 Ultra DMA mode 0 is supported.
1 Ultra DMA mode 1 is supported.
2 Ultra DMA mode 2 is supported.
3 Ultra DMA mode 3 is supported.
4 Ultra DMA mode 4 is supported.
5 Ultra DMA mode 5 is supported.
6 Ultra DMA mode 6 is supported.
8 Ultra DMA mode 0 is currently active.
9 Ultra DMA mode 1 is currently active.
10 Ultra DMA mode 2 is currently active.
11 Ultra DMA mode 3 is currently active.
12 Ultra DMA mode 4 is currently active.
13 Ultra DMA mode 5 is currently active.
14 Ultra DMA mode 6 is currently active.
Seagate IronWolf Product Manual, Rev. P 36
www.seagate.com SATA Interface
4.3.2 Set Features command
This command controls the implementation of various features that the drive supports. When the drive receives this command, it
sets BSY, checks the contents of the Features register, clears BSY and generates an interrupt. If the value in the register does not
represent a feature that the drive supports, the command is aborted. Power-on default has the read look-ahead and write caching
features enabled. The acceptable values for the Features register are defined as follows:
Table 14 Set Features commands
02HEnable write cache (default).
03HSet transfer mode (based on value in Sector Count register).
Sector Count register values:
00HSet PIO mode to default (PIO mode 2).
01HSet PIO mode to default and disable IORDY (PIO mode 2).
08HPIO mode 0
09HPIO mode 1
0AHPIO mode 2
0BHPIO mode 3
0CHPIO mode 4 (default)
20HMultiword DMA mode 0
21HMultiword DMA mode 1
22HMultiword DMA mode 2
40HUltra DMA mode 0
41HUltra DMA mode 1
42HUltra DMA mode 2
43HUltra DMA mode 3
44HUltra DMA mode 4
45HUltra DMA mode 5
46HUltra DMA mode 6
06HEnable the PUIS feature set
07HPUIS feature set device spin-up
10HEnable use of SATA features
55HDisable read look-ahead (read cache) feature
82HDisable write cache
86HDisable the PUIS feature set
90HDisable use of SATA features
AAHEnable read look-ahead (read cache) feature (default).
F1HReport full capacity available
Note At power-on, or after a hardware or software reset, the default values of the features are as indicated above.
Seagate IronWolf Product Manual, Rev. P 37
www.seagate.com SATA Interface
4.3.3 S.M.A.R.T. commands
S.M.A.R.T. provides near-term failure prediction for disk drives. When S.M.A.R.T. is enabled, the drive monitors predetermined drive
attributes that are susceptible to degradation over time. If self-monitoring determines that a failure is likely, S.M.A.R.T. makes a
status report available to the host. Not all failures are predictable. S.M.A.R.T. predictability is limited to the attributes the drive can
monitor. For more information on S.M.A.R.T. commands and implementation, see the Draft ATA-5 Standard.
SeaTools diagnostic software activates a built-in drive self-test (DST S.M.A.R.T. command for D4H) that eliminates unnecessary drive
returns. The diagnostic software ships with all new drives and is also available at:
seatools.seagate.com.
This drive is shipped with S.M.A.R.T. features enabled. Table 15 below shows the S.M.A.R.T. command codes that the drive uses.
Table 15 S.M.A.R.T. commands
Code in features register S.M.A.R.T. command
D0HS.M.A.R.T. Read Data
D2HS.M.A.R.T. Enable/Disable Attribute Autosave
D3HS.M.A.R.T. Save Attribute Values
D4HS.M.A.R.T. Execute Off-line Immediate (runs DST)
D5HS.M.A.R.T. Read Log Sector
D6HS.M.A.R.T. Write Log Sector
D8HS.M.A.R.T. Enable Operations
D9HS.M.A.R.T. Disable Operations
DAHS.M.A.R.T. Return Status
Note If an appropriate code is not written to the Features Register, the
command is aborted and 0x04 (abort) is written to the Error register.
Seagate Technology LLC
AMERICAS Seagate Technology LLC 47488 Kato Road, Fremont, California 94538, United States, 510-661-1000
Publication Number: 100807039, Rev. P
January 2022