Shuttle Touch PC System POS X5050PA (black) User Manual
Displayed below is the user manual for Touch PC System POS X5050PA (black) by Shuttle which is a product in the POS Systems category. This manual has pages.
Related Manuals
X50V5 Series Quick Guide【English】
2.
Refasten the stand and the back cover with eight screws.
To place the machine on the desk and to carry it, do the following:
Place the X50V5 on a at surface such as a table (Picture 1), and pull the stand
upwards to an angle of 30° (Picture 2). To carry or move your X50V5 fully extend
the angle to 180° (Picture 3).
E VESA mounting it to the wall
E Placing on the desk
E Front / Rear / Side View
Run the screen calibration
program and perform a 4
points on-screen calibration.
Click Start / All Programs
/ eGalax Touch
/ Congure Utility
Select [Tools] tab and click
[4 Points Calibration]
E How to use the Touch Panel
E 4 Points Calibration (Installation from CD-ROM)
Experience the ease of managing your digital life with a few touches by using the
stylus. The touch of your nger replaces the mouse and this is all you need to
interact with the X50V5.
Touch and hold the center of the target.
Repeat on four corners and the screen will adjust automatically.
When the 4 points calibration completed, press “OK” to continue.
E Cleaning the screen
Follow these guidelines for cleaning the outside and handling the screen of the computer:
Turn o the system and disconnect all cables.
Use a damp or cleaning cloth, ideally soft, lint-free and lightly humid to wipe the screen.
・Touch = left-click on the mouse
・Touch and hold = right-click on the mouse
Follow the steps (1~3) below to connect the AC adapter to the “DC-IN jack”.
Press the “Power Button” to turn on the system.
E Powering on the system
01 Stand / Handle
02 Microphone
03 Webcam
04 LCD Display (Single Touch)
05 Hard Disk Drive LED
06 Power LED
07 Stereo Speakers
08 Printer Port (Optional)
Note : The X50V5 can be mounted to a wall using a VESA compatible 75 x75
mm or 100 x 100mm wall/arm bracket.
If you are mounting your X50V5 to the wall, remove the cover on the back of
the X50V5 rst.
Unscrew four screws of the stand mount and remove the stand. The VESA
standard lets users mount it on to walls easily. Please refer to the user guide
of the wall/arm mount kit you bought separately to install it.
Note: The product’s colour and specications may vary from the actually shipping product.
E Safety Information
Read the following precautions before setting up a Shuttle X50V5.
CAUTION
Do not walk on the power cord or allow anything to rest on it.
Danger of explosion if battery is incorrectly replaced. Replace only with the same
or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer’s instructions.
A. Begin Installation
1.
Remove the cover on the back of the X50V5 rst, unscrew
four screws of the stand mount and remove the stand.
For safety reasons, please ensure that the power
cord is disconnected before opening the case.
Latch Latch
B. HDD or SSD Installation
1.
Unscrew four screws of the bracket and remove it.
2.
Mount the HDD or SSD into the bracket with four screws.
1.
Replace the back cover.
E. Complete
2.
Unscrew four screws of the back cover and remove it.
3.
Replace the cover, complete.
Cover
Screw
4.
Carefully push down the memory module until it snaps into
the locking mechanism.
Back Cover
Screw
Stand / Handle
Stand / Handle
75 x75 mm
100 x 100mm
09 COM1 and COM2 Ports (Optional)
10 VGA Port
11 Kensington® Lock Port
12 Power Button
13 Stylus
14 SD Card Reader
15 USB 2.0 Ports
16 Headphone / Line-out Jack
17 Microphone Jack
18 HDMI Port HDMI
19 USB 3.0 Ports
20 LAN Port
21 USB 2.0 Ports
22 DC In DC-IN
23 RJ11 DIO Port for Cash Drawer (Optional)
24 COM3, COM4 over RJ45 (Optional)
02
04
03
05
07
13
14
07
06
09
08
12
10
11
15
16
17
181922 20212324
01
1.
Locate the SO-DIMM slot on the mainboard.
3.
Gently insert the
module into the slot
in a 45-degree angle.
SO-DIMM slot
4.
Install the HDD or SSD & bracket in the chassis and tighten
the HDD or SSD & bracket with four screws.
C. Memory Module Installation
2.
Align the notch of the
memory module with the
one of the memory slot.
45-degree
angle
3.
Connect the Serial ATA and power cable to the HDD or SSD.
Serial ATA and power cable
Use DDR3L SO-DIMM only!
180
3.2.1.
30
53R-X50V53-H001
Unscrew
This mainboard does only support 1.35V DDR3L
memory modules.
D. Component Installation
1.
As shown, unfasten the screw rst.
2.
Please install the M.2 card into the M key slot and secure
with a screw.
M.2 2280 M Key slot
Hold OK
Touch
Model: X50V5 FCC ID : S8C-X50V5
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
Made in Taiwan Brand Name: Shuttle