Sony BRC-H800 User Manual

Displayed below is the user manual for BRC-H800 by Sony which is a product in the Security Cameras category. This manual has pages.

Related Manuals

Sony Sony Stativ VCT-SGR1 Manual

Sony Sony Bravia 85" X85K Manual

Sony KDL-46EX720BAEP Manual

Color Video Camera

Command List

BRC-X1000/H800/H780

C-456-100-13 (1)

Table of Contents

VISCA Commands ................................................3

Overview of VISCA ...........................................3

VISCA Communication Specifications ..............4

VISCA Device Setting Command ......................6

VISCA Command/ACK Protocol ......................7

VISCA Camera-Issued Messages .......................8

VISCA over IP ........................................................9

Overview of VISCA over IP ...............................9

Communication method of VISCA over IP ......10

BRC-X1000/H800/H780 Commands ..................14

Command List (1/5) ..........................................14

Command List (2/5) ..........................................15

Command List (3/5) ..........................................16

Command List (4/5) ..........................................17

Command List (5/5) ..........................................18

Inquiry Command List (1/4) .............................19

Inquiry Command List (2/4) .............................20

Inquiry Command List (3/4) .............................21

Inquiry Command List (4/4) .............................22

Block Inquiry Command List ...........................23

VISCA Command Setting Values ....................29

Pan/Tilt Status Code List ..................................31

Memory Function (Inquiry Commands) ...........32

PTZ TRACE function Record status bulk

inquiry .............................................................32

PRESET MODE settings and PRESET command

behaviors .........................................................33

Camera IP Setting Command .............................34

Revision History ...................................................35

VISCA1) Commands

Use of control software based upon this command list

may cause malfunction or damage to hardware and

software. We are not liable for any such damage.

Overview of VISCA

In VISCA, the side outputting commands, for example,

a computer, is called the controller, while the side

receiving the commands, such as a BRC-X1000/H800/

H7802), is called the peripheral device. In VISCA, up to

seven peripheral devices including this unit can be

connected to a single controller using communication

conforming to the RS-422 standard. The parameters of

RS-422 are as follows.

• Communication speed: 9600 bps/38400 bps

• Data bits : 8

• Start bit : 1

• Stop bit : 1

• Non parity

Flow control using XON/XOFF and RTS/CTS, etc., is

not supported.

Peripheral devices are connected in a daisy chain. As

shown in Fig. 1, the actual internal connection is a one-

direction ring, so that messages return to the controller

via the peripheral devices. The devices on the network

are assigned addresses.

The address of the controller is fixed at 0.

The addresses of peripheral devices are as follows.

When the camera address selector is set to 0

(automatic setting mode)

The peripheral devices are assigned to the addresses, 1,

2, 3… in the connected order, starting from the one

connected nearest to the controller. These addresses are

set when the controller sends address commands during

initialization of the network.

When the camera address selector is set to 1

through 7 (manual setting mode)

The addresses of the peripheral devices will be set to the

pre-selected numbers. Within a single system, the same

number can be used only once. If an address switch is

used in a setting other than 0, set the address switch on

this connected unit to different numbers.

Note

In the same network, all the camera address selectors

should be set to “0” (automatic setting) or all the

selectors should be manually set to “1” to “7”. Do not

mix the automatic and manual settings.

Each VISCA equipment has VISCA IN and VISCA

OUT connectors.

Set the DTR input (the S output of the controller) of

VISCA IN to H when controlling VISCA equipment

from the controller.

Fig. 1 VISCA network configuration

VISCA Equipment

OUT

VISCA Controller

............................................................................................................................................................................................................................

1) VISCA is a protocol developed by Sony for controlling a consumer’s camcorder. “VISCA” is a trademark of Sony Corporation.

2) The product name of this unit, “Color video camera BRC-X1000/H800/H780” is referred to as “the unit” or “color video camera” in

this document. BRC-H780 is the model on sale in China.

VISCA Communication

Specifications

VISCA packet structure

The basic unit of VISCA communication is called a

packet (Fig. 2). The first byte of the packet is called the

header and comprises the sender’s and receiver’s

addresses. For example, the header of the packet sent to

the unit (address 1) from the controller (address 0) is

81H in hexadecimals. Packet sent to the unit (address 2)

is 82H. In the command list, as the header is 8X, input

the address of the unit to X. The header of the reply

packet from the unit assigned address 1 is 90H. The

packet from the unit assigned address 2 is A0H.

Some of the setting commands can be sent to all devices

at one time (broadcast) *.

In the case of broadcast, the header should be 88H in

hexadecimal.

When the terminator is FFH, it signifies the end of the

packet.

* The broadcast function is not available for VISCA over IP.

Fig. 2 Packet structure

Note

Fig. 2 shows the packet structure, while Fig. 3 shows the

actual waveform. Data flow will take place with the LSB

first.

Fig. 3 Actual waveform for 1 byte.

Bit 7

(MSB)

Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0

(LSB)

Bit 7

(MSB)

Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0

(LSB)

11111111

Packet (3 to 16 bytes)

Message (1 to 14 bytes)

Byte 1 Byte 2 Byte 3

Sender’s

address Receiver’s address

Header Terminator

Bit 0 Bit 1 Bit 2 Bit 3 Bit 4 Bit 5

(LSB) (MSB)

Bit 6 Bit 7

1 byte

Start

bit

Stop

bit.

Timing Chart

As VISCA command processing can only be carried out

a maximum of one time in a Vertical (V) cycle, it takes

maximum 4V-cycle time for an ACK/Completion to be

returned.

If the Command and ACK/Completion communication

time is shorter than 1V-cycle time, a command can be

received at every 1V cycle. From this point, if two or

more commands are to be sent successively, wait for a

reply command (an ACK or error message for a general

command, and an inquiry packet for an inquiry

command) of the previous command to be received

before sending the next command.

1V= 16.7 msec (1080/59.94p, 1080/59.94i, 720/59.94p),

20 msec (1080/50p, 1080/50i, 720/50p),

33.4 msec (2160/29.97p (BRC-X1000 only)),

40 msec (2160/25p (BRC-X1000 only)),

41.7 msec (1080/23.98p*1, 2160/23.98p (BRC-X1000 only))

*1 This function is not available for BRC-H780.

Command and inquiry

•Command

Sends operational commands to the unit.

•Inquiry

Used for inquiring about the current state of the unit.

Command Packet Note

Inquiry 8X QQ RR ... FF QQ

= Command/Inquiry,

= category code

QQ = 01 (Command), 09 (Inquiry)

RR = 00 (Interface), 04 (camera 1), 06 (Pan/Tilter)

X = 1 to 7: Address of the unit*

* Locked to “X = 1” for VISCA over IP.

For actual values to be sent, see Command Lists or

Inquiry Command Lists.

Responses for commands and inquiries

•ACK message

Returned by the unit when it receives a command. No

ACK message is returned for an inquiry.

•Completion message

Returned by the unit when execution of commands or

inquiries is completed. In the case of inquiry

commands, reply data for the inquiry is contained

after the 3rd byte of the packet. If the ACK message is

omitted, the socket number will contain 0.

Reply Packet Note

Ack X0 4Y FF Y = socket number

Completion (Commands) X0 5Y FF Y = socket number

Completion (Inquiries) X0 5Y ... FF Y = socket number

X = 9 to F: Address of the unit + 8

* Locked to “X = 9” for VISCA over IP.

•Error message

When a command or inquiry command could not be

executed or failed, an error message is returned

instead of a completion message.

Error Packet Description

X0 6Y 01 FF Message length error

X0 6Y 02 FF Syntax Error

X0 6Y 03 FF Command buffer full

X0 6Y 04 FF Command canceled

X0 6Y 05 FF No socket (to be canceled)

X0 6Y 41 FF Command not executable

X = 9 to F: Address of the unit + 8, Y = socket number

* Locked to “X = 9” for VISCA over IP.

Socket number

When command messages are sent to the unit, it is

normal to send the next command message after

receiving the completion message or error message.

However, to deal with advanced uses, the unit has two

sets of buffers (memories) for commands, so that up to

two commands including the commands currently being

executed can be received. (There is a wait longer than a

1V cycle between commands.) However, depending on

the command, it may be necessary to wait until the first

command is completed due to system reasons. When the

unit receives commands, it notifies which command

buffer was used using the socket number of ACK

message.

As the completion message or error message also has a

socket number, it indicates which command has ended.

Even when two command buffers are being used, the

unit management command and some inquiry messages

can be executed.

The ACK message is not returned for these commands

and inquiries, and only the completion message of

socket number 0 is returned.

Command

Within 4V

RxD

TxD

ACK Completion

Within 4V

RxD

TxD

Inquiry Packet

Command

General commands

Inquiry commands

16 Bytes

Command execution cancel

To cancel a command which has already been sent, send

a Cancel command as the next command. To cancel one

of two commands which have been sent, use the cancel

message.

Cancel Packet Note

Cancel 8X 2Y FF Y = socket number

X = 1 to 7: Address of the unit, Y = socket number

* Locked to “X = 1” for VISCA over IP.

Error message “Command cancelled” will be returned

for this command, but this is not a fault. It indicates that

the command has been cancelled.

Note

To cancel a command when VISCA PAN-TILT Drive

(page 17) is being executed, wait at least 200 msec after

executing. Then send a cancel command to ensure that

PAN-TILT Drive stops effectively.

To execute a PAN-TILT Drive command again, wait at

least 200 msec after the message “Command cancelled”

has appeared.

VISCA Device Setting Command

Before starting control of the unit, make sure to send the

Address command and IF_Clear command using the

broadcast.

For VISCA network administration

•Address*

Sets an address of a peripheral device. Use when

initializing the network, and receiving the following

network change message.

* Not available for VISCA over IP.

•Network Change*

Sent from the peripheral device to the controller when

a device is removed from or added to the network. The

address must be re-set when this message is received.

* Not available for VISCA over IP.

Packet Note

Address 88 30 01 FF Always broadcasted.

Network Change X0 38 FF

X = 9 to F: Address of the unit + 8

VISCA interface command

•IF_Clear

Clears the command buffer in the unit. When cleared,

the operation currently being executed is not

guaranteed.

Command Packet Reply Packet Note

IF_Clear 8X 01 00 01 FF X0 50 FF

IF_Clear (broadcast)

88 01 00 01 FF 88 01 00 01 FF

X = 1 to 7: Address of the unit (For inquiry packet)

X = 9 to F: Address of the unit +8 (For reply packet)

*1 The broadcast function is not available for VISCA over IP.

*2 Locked to “X = 1” for VISCA over IP.

*3 Locked to “X = 9” for VISCA over IP.

VISCA interface and inquiry

•CAM_VersionInq

Returns information on the VISCA interface.

Inquiry Inquiry Packet Reply Packet Description

CAM_VersionInq 8X 09 00 02 FF Y0 50 GG GG HH HH JJ JJ KK FF GGGG = Vender ID

0001: Sony

HHHH = Model ID

0519: BRC-X1000

051A: BRC-H800

051B: BRC-H780

JJJJ = ROM revision

KK = Maximum socket # (02)

X = 1 to 7: Address of the unit (For inquiry packet)

X = 9 to F: Address of the unit +8 (For reply packet)

*1 Locked to “X = 1” for VISCA over IP.

*2 Locked to “X = 9” for VISCA over IP.

VISCA Command/ACK Protocol

*1 Not available for VISCA over IP.

*2 When the camera address selector is set to an address other than 0, the value x in 88 30 0x FF will be variable.

Do not transmit the command (except Address Set, IF_Clear, Command Cancel) when any menu is displayed on the

screen. If displayed, clear the menu first using MENU Display OFF (page 18) Command, and then proceed.

Command Command Message Reply Message Comments

General Command 81 01 04 38 02 FF

(Example)

90 41 FF (ACK)+90 51 FF

(Completion)

90 42 FF 90 52 FF

Returns ACK when a command has been accepted, or

Completion when a command has been executed.

81 01 04 38 FF

(Example)

90 60 02 FF

(Syntax Error)

Accepted a command which is not supported or a command

lacking parameters.

81 01 04 38 02 FF

(Example)

90 60 03 FF

(Command Buffer Full)

Could not accept the command as there are two commands

currently being executed.

81 01 04 08 02 FF

(Example)

90 61 41 FF

(Command Not Executable)

90 62 41 FF

Could not execute the command in the current mode.

Inquiry Command 81 09 04 38 FF

(Example)

90 50 02 FF (Completion) Does not return ACK.

81 09 05 38 FF

(Example)

90 60 02 FF

(Syntax Error)

Accepted an incompatible command.

Address Set*1 88 30 01 FF 88 30 02 FF The device address number plus 1 is returned.*2

IF_Clear

(Broadcast)*1

88 01 00 01 FF 88 01 00 01 FF The same command is returned.

IF_Clear (For x) 8x 01 00 01 FF y0 50 FF (Completion) ACK is not returned for this command.

Command Cancel 8x 2p FF y0 6p 04 FF

(Command Cancelled)

Returned when the command of the socket specified is

cancelled. Completion for the command cancelled is not

returned.

y0 6p 04 FF

(No Socket)

Returned when the command of the specified socket has

already been completed or when the socket number specified

is wrong.

VISCA Camera-Issued Messages

ACK/Completion Messages

z = Device address + 8 (Locked to “z = 9” for VISCA over IP.)

Error Messages

z = Device address + 8 (Locked to “z = 9” for VISCA over IP.)

Network Change Message*

* Not available for VISCA over IP.

Command Command Message Comments

ACK z0 4y FF

(y: Socket No.)

Returned when the command is accepted.

Completion z0 5y FF

(y: Socket No.)

Returned when the command has been executed.

Command Command Message Comments

Syntax Error z0 60 02 FF Returned when the command format is different or when a command with

illegal command parameters is accepted.

Command Buffer Full z0 60 03 FF Could not accept a command that is received while two commands are

currently being executed (two sockets have been used).

Command Cancelled z0 6y 04 FF

(y: Socket No.)

Returned when a command which is being executed in a socket specified by

the cancel command is cancelled. The completion message for the command

is not returned.

No Socket z0 6y 05 FF

(y: Socket No.)

Returned when no command is executed in a socket specified by the cancel

command, or when an invalid socket number is specified.

Command Not Executable z0 6y 41 FF

(y: Socket No.)

Returned when a command cannot be executed due to current conditions.

For example, when a command for controlling the manual focus is received

during the auto focus mode.

Command Command Message Comments

Network Change z0 38 FF Issued when power is supplied to the camera.

VISCA over IP

Overview of VISCA over IP

With VISCA over IP function, you can control the

camera using VISCA on a controller equipped with IP

communication capabilities via LAN. You can connect

up to 5 controllers simultaneously on the network.

The communication specifications of VISCA over IP are

as follows:

• Interface

RJ-45 10Base-T/100Base-TX (automatically

identifying)

• Internet protocol

IPv4

• Transport protocol

UDP

•IP address

Set by the IP card setting command (page 34)

• Port address

52381

• Delivery confirmation/Retransmission control

Depends on the application

In these instructions, the device outputting commands,

for example, a computer, is called the controller, and the

device receiving the command, such as a BRC series

camera, is called a peripheral device.

The controllers and peripheral devices are connected to

a one-direction ring conforming to RS-422 standards.

On the IP communication connection, the controllers

and peripheral devices are connected by bus through a

LAN.

RS422 connection

IP communication connection

While the IP communication connection, the address of

each device cannot be set in the VISCA message as it is

because the controllers and peripheral devices that are

connected simultaneously are increased. In this case,

addresses of the controllers and peripheral devices that

are set in the VISCA message are locked to 0 (for the

controller) or 1 (for the peripheral device).

VISCA Equipment

OUT

VISCA Controller

VISCA Equipment

VISCA Controller

VISCA Equipment

VISCA Controller

Network

Due to the nature of the IP communication, the use of

some VISCA functions are limited. For details, see

“Camera IP Setting Command” on page 34.

For how to set an IP address of the camera, refer to

“Camera IP Setting Command” on page 34.

Communication method of VISCA

over IP

Communication method

VISCA over IP can process the VISCA communication

between the controllers and peripheral devices using the

messages that can be identified on the LAN, and sends/

receives them. Because of this, VISCA over IP is not

concerned about the contents of the communication

between the controllers and peripheral devices.

However, the VISCA communication sequence is

different, depending on the types, as follows.

VISCA command

This is a command from the controller to the peripheral

device.

When the peripheral device receives this command,

ACK is returned. After completing command

processing, a completion notice is returned. This

command uses the socket of VISCA. The order of

completion notices may be changed if the multiple

commands are sent to the same peripheral device.

VISCA inquiry

This is an inquiry from the controller to the peripheral

device.

When the peripheral device receives this type of

command, the reply for the inquiry is returned. This

command does not use the socket of VISCA. The order

of the replies is not changed if a multiple commands are

sent.

VISCA reply

This is an ACK, completion notice, reply, or error reply

from the peripheral device to the controller.

The classification for sending messages from the

peripheral device to the controller is common.

VISCA device setting command

This is the device setting command from the controller

to the peripheral device as follows.

• Address

Sets the address of the peripheral device, and does not

return a reply to the controller. While using VISCA

over IP, the address command is not sent from the

controller because a Network Change command from

the peripheral device that triggers sending command is

not issued.

•IF_Clear

Sends the reply message to the controller after

clearing, without using VISCA socket.

• CAM_VersionInq

Sends the reply message to the controller, without

using VISCA socket.

Format

These are the specifications of the message header (8

bytes) and payload (1 to 16 bytes).

Message structure

Note

The actual LAN out method is big-endian, LSB first.

Byte 0 Byte 1 Byte 2 Byte 3

Byte 8 Byte 9

Byte 4 Byte 5 Byte 6 Byte 7

Message (9 to 24 bytes)

Message header Payload (1 to 16 bytes)

Payload type Payload length Sequence number

Payload type

Stores the value (Byte 0 and Byte 1) of the following table on the payload division.

Payload length

Stores the number of bytes (1 to 16) of data is stored on

the payload.

Example: When the payload length is 16 bytes.

Byte 2: 0x00

Byte 3: 0x10

Sequence number

The controller stores the sequence number that is added

every time a message is sent. If the sequence number

reaches the limit, next value will be 0. The peripheral

device saves the sequence number in the message from

the controller, and stores the sequence number of the

received message corresponding to the message sent to

the controller.

Payload

Depending on the payload type, the following are stored.

• VISCA command

Stores the packet of the VISCA command.

• VISCA inquiry

Stores the packet of VISCA message.

• VISCA reply

Stores the reply for the command or inquiry (ACK

message, completion message, or error message).

• VISCA device setting command

Stores the packet of the VISCA device setting

command.

• Control command

The following are stored on the payload division of the

control command.

• Controlled reply

The following are stored on the payload division of the

reply for the control command.

Name Value (Byte 0) Value (Byte 1) Description

VISCA command 0x01 0x00 Stores the VISCA command.

VISCA inquiry 0x01 0x10 Stores the VISCA inquiry.

VISCA reply 0x01 0x11 Stores the reply for the VISCA command and VISCA

inquiry, or VISCA device setting command.

VISCA device

setting command

0x01 0x20 Stores the VISCA device setting command.

Control command 0x02 0x00 Stores the control command.

Control reply 0x02 0x01 Stores the reply for the control command.

Name Value Description

RESET 0x01 Resets the sequence number

to 0. The value that was set as

the sequence number is

ignored.

ERROR 0x0Fyy yy=01: Abnormality in the

sequence number.

yy=02: Abnormality in the

message (message type)

Message Value Description

ACK 0x01 Reply for RESET.

Delivery confirmation

VISCA over IP uses UDP as a communications protocol of the transport layer. Delivery of messages is not guaranteed

for the UDP communication. Delivery confirmation and retransmission should be performed on the application.

Normally, when the controller sends a message to the peripheral device, the controller sends the new message after

receiving the reply for the last message. You can confirm delivery of messages by managing the time-out waiting for a

reply message sent.

If time out occurs on the controller, loss of one of the following messages is considered:

• Command

• ACK message

• Completion message for the command

• Inquiry

• Reply message for the inquiry

• Error message

• Inquiry of the VISCA device setting command

• Reply message of the VISCA device setting command

If time out occurs on the controller, you can infer the lost message and state of the peripheral device by retransmitting

the message using the same sequence number. The following table shows the received message and status by

retransmission of the lost message, and the reference of correspondence after retransmission for each case. (Except for

the case that a time out occurs for reasons other than loss of message.)

The BRC series camera has 2 buffers (memories) for the command to deal with advanced uses. When using VISCA

over IP, up to 2 commands (including the current command) can be received. Depending on the message from the

controller to the peripheral device, there are some messages that do not need to guarantee delivery. However, the

peripheral device receives commands from multiple controllers while connected to VISCA over IP. If the multiple

commands are send without waiting for the reply, the possibility of non-execution of the command and errors due to

buffer overflow become high, because of limitations of order to receive commands or execution interval of command.

It may cause efficiency to be reduced substantially.

Lost message Received message for

retransmission

Status after

retransmission

Correspondence after retransmission

Command ACK message Command is performed by

retransmission.

Continue processing.

ACK message ERROR (Abnormality in

the sequence number.)

Command has been

performed.

If only the ACK message is

lost, the completion message

returns.

If the result by the completion message is needed,

retransmit by updating the sequence number.

Completion message

for the command

ERROR (Abnormality in

the sequence number.)

Command has been

performed.

If the result by the completion message is needed,

retransmit by updating the sequence number.

Inquiry Reply message Inquiry is performed by

retransmission.

Continue processing.

Reply message for the

inquiry

ERROR (Abnormality in

the sequence number.)

Inquiry has been performed. If the result by the reply message is needed,

retransmit by updating the sequence number.

Error message Error message Command is not performed.

If the error cause eliminates,

normal reply is returns (ACK,

reply message).

Eliminate the error cause. If normal reply returns,

continue processing.

Inquiry of the VISCA

device setting

command

Reply message of the

VISCA device setting

command

Inquiry has been performed

by retransmission.

Continue processing.

Reply message of the

VISCA device setting

command

ERROR (Abnormality in

the sequence number.)

Inquiry has been performed. If the result by the reply message is needed,

retransmit by updating the sequence number.

Timing chart

Timing chart (loss of command)

Timing chart (loss of ACK or completion message)

Limitation

The following are limitations for VISCA over IP as

compared with the VISCA specifications.

Locking the peripheral device’s address of the

VISCA message to 1

VISCA over IP cannot reflect each address to the

address of the VISCA message because up to 112

peripheral devices and 5 controllers are connected.

Because of this, the peripheral device’s address of

VISCA command is locked to 1 when using VISCA

over IP. If the peripheral device’s address is set to other

than 1 for the VISCA command, the peripheral device

works without hindrance since the peripheral device

recognizes that its address is set to 1.

Locking the controller’s address of the VISCA

message to 0.

For the same reason as the peripheral device’s address,

the controller’s address of VISCA command is locked to

0. If the controller’s address is set to other than 0, the

peripheral device works without hindrance, and the

reply address from the peripheral device is always set to

Prohibition of specifying the broadcast address

for the VISCA message

Do not use the broadcast address because it requires the

serial communication. Operations under the broadcast

address is set to the command are not guaranteed.

Prohibition of the address for VISCA device

setting command

Do not use this command because it requires the serial

communication. Operations under the address command

is sent are not guaranteed.

VISCA Network Change command is not

supported

This cannot be issued because it requires the serial

communication.

Expiration time for an on status of the tally lamp

The tally lamp is turned off if not receiving an on

command from any controller for 15 seconds after

receiving an on command of Cmd_Tally.

Command seq=100

ACK seq=100

Completion seq=100

Controller Peripheral device

Time out

ERROR

(abnormality in the sequence number)

seq=100

ACK seq=100

Completion seq=100

Command seq=100

Command seq=101

ACK seq=101

Completion seq=101

Controller Peripheral device

Time out

BRC-X1000/H800/H780 Commands

Command List (1/5)

Number in ( ) is MENU display values.

*1 This function is not available for BRC-H780.

Command Set Command Command Packet Comments

EXPOSURE MODE FULL AUTO 8x 01 04 39 00 FF Automatic Exposure mode

MANUAL 8x 01 04 39 03 FF Manual Control mode

SHUTTER Pri 8x 01 04 39 0A FF Shutter Priority Automatic Exposure mode

IRIS Pri 8x 01 04 39 0B FF Iris Priority Automatic Exposure mode

Gain Pri 8x 01 04 39 0E FF

IRIS Reset 8x 01 04 0B 00 FF To return to F2.8 value

Up (Open) 8x 01 04 0B 02 FF

Down (Close) 8x 01 04 0B 03 FF

Direct 8x 01 04 4B 00 00 0p 0p FF pp: Iris Position 05 - 15

GAIN Reset 8x 01 04 0C 00 FF To return to 0 dB

Up 8x 01 04 0C 02 FF

Down 8x 01 04 0C 03 FF

Direct 8x 01 04 4C 00 00 0p 0p FF pp: 00 (–3dB) - 0C (33 dB)

GAIN LIMIT Direct

8x 01 04 2C 0p FF

p: 4 (9dB) - 9 (24dB), F (Off)

GAIN POINT On/Off 8x 01 05 0C 0p FF p: 2=On, 3=Off

GAIN POINT

POSITION

Direct 8x 01 05 4C 0p 0p FF pp: 01 (0dB) - 09 (24dB)

SHUTTER Reset 8x 01 04 0A 00 FF Return to the default value depending on the

frame rate of video output

Up (Fast) 8x 01 04 0A 02 FF

Down (Slow) 8x 01 04 0A 03 FF

Direct 8x 01 04 4A 00 00 0p 0p FF pp: Shutter Position (01 - 15)

MAX SHUTTER Direct 8x 01 05 2A 00 0p 0p FF pp: 03 - 15

MIN SHUTTER Direct 8x 01 05 2A 01 0p 0p FF pp: 03 - 15

AE SPEED Direct 8x 01 04 5D pp FF pp: 01 - 30

EXP COMP On/Off 8x 01 04 3E 0p FF p: 2=On, 3=Off

Reset 8x 01 04 0E 00 FF To return to 0 value

Up 8x 01 04 0E 02 FF

Down 8x 01 04 0E 03 FF

Direct 8x 01 04 4E 00 00 0p 0p FF pp: 00 - 0E

BACK LIGHT On/Off 8x 01 04 33 0p FF p: 2=On, 3=Off

SPOT LIGHT On/Off 8x 01 04 3A 0p FF p: 2=On, 3=Off

VISIBILITY

ENHANCER

On/Off 8x 01 04 3D 03 FF Off

8x 01 04 3D 06 FF On

Direct 8x 01 04 2D 00 0p 0q 0r 00

00 00 00 FF

p: Effect level 0 (Dark) - 6 (Bright)

q: Brightness compensation selection 0 (Very

dark), 1 (Dark),2 (Standard), 3 (Bright)

r: Compensation level 0 (Low), 1 (Mid), 2 (High)

IR CUT

FILTER*1

On/Off 8x 01 04 01 0p FF p: 2=On (Night), 3=Off (Day)

LOW LIGHT

BASIS

BRIGHTNESS

On/Off 8x 01 05 39 0p FF p: 2=On, 3=Off

Direct 8x 01 05 49 0p FF p: 4 - A

ND FILTER - 8x 01 7E 01 53 0p FF p: 0=Off, 1=1/4, 2=1/16, 3=1/64

Command List (2/5)

* Number in ( ) is MENU display values.

Command Set Command Command Packet Comments

COLOR WHITE

BALANCE

Auto1 8x 01 04 35 00 FF

Indoor 8x 01 04 35 01 FF

Outdoor 8x 01 04 35 02 FF

One Push WB 8x 01 04 35 03 FF

Auto2 8x 01 04 35 04 FF

Manual 8x 01 04 35 05 FF

ONE PUSH

TRIGGER

One Push

Trigger

8x 01 04 10 05 FF One Push WB Trigger

R.GAIN Reset 8x 01 04 03 00 FF To return to 80 (0) value

Up 8x 01 04 03 02 FF

Down 8x 01 04 03 03 FF

Direct 8x 01 04 43 00 00 0p 0p FF pp: 00 (–128) - 80 (0) - FF (128)

B.GAIN Reset 8x 01 04 04 00 FF To return to 80 (0) value

Up 8x 01 04 04 02 FF

Down 8x 01 04 04 03 FF

Direct 8x 01 04 44 00 00 0p 0p FF pp: 00 (–128) - 80 (0) - FF (128)

SPEED 8x 01 04 56 0p FF p: speed 1 (Slow) - 5 (Fast)

OFFSET Reset 8x 01 7E 01 2E 00 00 FF To return to 7 (0) value

Up 8x 01 7E 01 2E 00 02 FF

Down 8x 01 7E 01 2E 00 03 FF

Direct 8x 01 7E 01 2E 01 0p FF p: 0 (–7) - 7 (0) - E (+7)

CHROMA

SUPPRESS

- 8x 01 04 5F 0p FF p: 0 (Off), 1 (Weak) - 3 (Strong)

MATRIX Select 8x 01 7E 01 3D 0p FF p: Matrix Setting (2=STD, 3=OFF, 4=HIGH SAT,

5=FL LIGHT, 6=MOVIE, 7=STILL,

8=CINEMA, 9=PRO, A=ITU709, B=B/W)

LEVEL Reset 8x 01 04 09 00 FF To return to 4 value

Up 8x 01 04 09 02 FF

Down 8x 01 04 09 03 FF

Direct 8x 01 04 49 00 00 00 0p FF p: 0 (0) - E (14)

PHASE Reset 8x 01 04 0F 00 FF To return to 7 (0) value

Up 8x 01 04 0F 02 FF

Down 8x 01 04 0F 03 FF

Direct 8x 01 04 4F 00 00 00 0p FF p: 0 (–14 degrees) - E (+14 degrees)

R-G Direct 8x 01 7E 01 7A 0p 0p FF pp: 00 (–99) - 63 (00) - C6 (+99)

R-B Direct 8x 01 7E 01 7B 0p 0p FF pp: 00 (–99) - 63 (00) - C6 (+99)

G-R Direct 8x 01 7E 01 7C 0p 0p FF pp: 00 (–99) - 63 (00) - C6 (+99)

G-B Direct 8x 01 7E 01 7D 0p 0p FF pp: 00 (–99) - 63 (00) - C6 (+99)

B-R Direct 8x 01 7E 01 7E 0p 0p FF pp: 00 (–99) - 63 (00) - C6 (+99)

B-G Direct 8x 01 7E 01 7F 0p 0p FF pp: 00 (–99) - 63 (00) - C6 (+99)

DETAIL LEVEL Reset 8x 01 04 02 00 FF To return to 7 (0) value

Up 8x 01 04 02 02 FF

Down 8x 01 04 02 03 FF

Direct 8x 01 04 42 00 00 0p 0p FF pp: Aperture Gain 00 - 0F

MODE Direct 8x 01 05 42 01 0p FF p: Auto=0, Manual=1

BANDWIDTH Direct 8x 01 05 42 02 0p FF p: Band width 0 - 4

CRISPENING Direct 8x 01 05 42 03 0p FF p: Crispening 0 - 7

H/V BALANCE Direct 8x 01 05 42 04 0p FF p: 5 - 9

B/W BALANCE Direct 8x 01 05 42 05 0p FF p: 0 - 4

LIMIT Direct 8x 01 05 42 06 0p FF p: 0 - 7

HIGHLIGHTDE

TAIL

Direct 8x 01 05 42 07 0p FF p: 0 - 4

SUPERLOW Direct 8x 01 05 42 08 0p FF p: 0 - 7

Command List (3/5)

Number in ( ) is MENU display values.

*1 Cannot be used when the signal format is other than 1080/29.97p, 1080/25p, or 1080/23.98p.

Command Set Command Command Packet Comments

KNEE KNEE SETTING On/Off 8x 01 7E 01 6D 0p FF p: 2=On, 3=Off

KNEE MODE - 8x 01 7E 01 54 0p FF p: 0=Auto, 4=Manual

KNEE SLOPE Direct 8x 01 7E 01 6F 0p 0p FF pp: Knee Slope 00 - 0E

KNEE POINT Direct 8x 01 7E 01 6E 0p 0p FF pp: Knee Point 00 - 0C

GAMMA MODE - 8x 01 04 5B 0p FF p: GAMMA Setting (0=STD, 1=STRAIGHT,

2=PATTERN, 8=MOVIE, 9=STILL, A=CINE1,

B=CINE2, C=CINE3, D=CINE4, E=ITU709)

PATTERN Direct 8x 01 05 5B 0p 0p 0p FF ppp: 001 - 200

OFFSET Direct 8x 01 04 1E 00 00 00 0p 0q

0q FF

p: Offset polarity 0 (+), 1 (–)

qq: Offset width 00 - 40

LEVEL Direct 8x 01 7E 01 71 0p 0p FF pp: 00 - 0E

BLACK

GAMMA LEVEL

Direct 8x 01 7E 01 72 0p 0p FF pp: 00 - 0E

BLACK

GAMMA

RANGE

Direct 8x 01 05 5C 0p FF p: Correction range 0 (Low), 1 (Mid), 2 (High)

BLACK LEVEL Reset 8x 01 7E 04 15 00 FF To return to 30 (0) value

Up 8x 01 7E 04 15 02 FF

Down 8x 01 7E 04 15 03 FF

Direct 8x 01 7E 04 45 0p 0p FF pp: 00 (–48) - 60 (48)

PICTURE

PROFILE

MODE - 8x 01 7E 04 5F 0p FF p: Picture profile setting (0=PP1, 1=PP2,

2=PP3, 3=PP4, 4=PP5, 5=PP6)

FLICKER

REDUCTION

MODE On 8x 01 04 32 0p FF p:2=On, 3=Off

NOISE

REDUCTION

MODE LEVEL - 8x 01 04 53 pp FF pp: NR Setting 00 (Off), 01 (Weak) - 05 (Strong),

7F (Advanced)

2D NR/3D NR

MANUAL

SETTING

Direct 8x 01 05 53 0p 0q FF p: 2D NR Level 0 (Off), 1 (Weak) - 5 (Strong)

q: 3D NR Level 0 (Off), 1 (Weak) - 5 (Strong)

ZOOM STOP - 8x 01 04 07 00 FF

TELE

(STANDARD)

- 8x 01 04 07 02 FF

WIDE

(STANDARD)

- 8x 01 04 07 03 FF

TELE

(VARIABLE)

- 8x 01 04 07 2p FF p: 0 (Low) - 7 (High)

WIDE

(VARIABLE)

- 8x 01 04 07 3p FF p: 0 (Low) - 7 (High)

DIRECT - 8x 01 04 47 0z 0z 0z 0z FF zzzz:

0000 (wide) to 4000 (optical tele) to 5580 (Clear

Image Zoom tele 4K)

0000 (wide) to 4000 (optical tele) to 6000 (Clear

Image Zoom tele FHD)

CLEAR IMAGE

ZOOM

- 8x 01 04 06 03 FF OFF

8x 01 04 06 04 FF ON

TELE CONVERT

MODE

- 8x 01 7E 04 36 0p FF p: 2=Double, 3=Off*1

Command List (4/5)

* Number in ( ) is MENU display values.

Command Set Command Command Packet Comments

FOCUS MODE - 8x 01 04 38 02 FF Auto Focus

MANUAL

FOCUS

- 8x 01 04 38 03 FF Manual Focus

AUTO/

MANUAL

TOGGLE

- 8x 01 04 38 10 FF

STOP - 8x 01 04 08 00 FF

FAR

(STANDARD

SPEED)

- 8x 01 04 08 02 FF

NEAR

(STANDARD

SPEED)

- 8x 01 04 08 03 FF

FAR

(VARIABLE

SPEED)

- 8x 01 04 08 2p FF p: 0 (Low) - 7 (High)

NEAR

(VARIABLE

SPEED)

- 8x 01 04 08 3p FF p: 0 (Low) - 7 (High)

DIRECT Direct 8x 01 04 48 0p 0p 0p 0p FF pppp: F000 (Near) - 0000 (Far)

ONE PUSH

TRIGGER

- 8x 01 04 18 01 FF One Push AF Trigger

FOCUS ∞- 8x 01 04 18 02 FF

NEAR LIMIT Direct 8x 01 04 28 0p 0p 0p 0p FF pppp: 1000 - F000

SENSITIVITY

- 8x 01 04 58 0p FF p: 2 (Normal), 3 (Low)

CORRECTION

- 8x 01 04 11 0p FF p: 0 (Standard), 1 (IR Light)

PAN TILT

DRIVE

UP - 8x 01 06 01 vv ww 03 01 FF vv: Pan speed 01 (Slow) - 18 (Fast)