Table of Contents
- Table of Contents
- Chapter 1 Overview
- Chapter 2 Names and Functions of Parts
- Chapter 3 Preparations
- Chapter 4 Recording, Playback and Copy
- Chapter 5 Operations on Clip List Screens
- Chapter 6 File Operations
- Chapter 7 Menus
- Appendix
- Index
Sony PDW-HD1550 User Manual
Displayed below is the user manual for PDW-HD1550 by Sony which is a product in the Digital Audio Recorders category. This manual has pages.
Related Manuals
PROFESSIONAL DISC RECORDER
PDW-HD1550
OPERATION MANUAL [English]
1st Edition (Revised 6)
2Table of Contents
Table of Contents
Chapter 1 Overview
Features............................................................................................6
Features of this unit ............................................................................... 6
System Configurations ...................................................................9
Chapter 2 Names and Functions of Parts
Front Panel .....................................................................................10
Display screen ..................................................................................... 15
Rear Panel ......................................................................................20
Chapter 3 Preparations
Preparing Power Sources .............................................................23
Supplying power.................................................................................. 23
Attaching a battery pack...................................................................... 23
Initial Setup ....................................................................................25
Front Panel Tilt Mechanism ..........................................................26
Connections and Settings ............................................................27
Connections for Content Browser and non-Sony nonlinear editors.... 27
Connections for cut editing ................................................................. 28
Using the editing functions of the recorder (controlling through
REMOTE (9P) connector) ......................................................... 31
Connections for pool coverage............................................................ 32
Synchronization Reference Signals.............................................33
Setting the System Frequency .....................................................34
Setting the Timecode ....................................................................34
Superimposed Text Information...................................................36
Basic Operations of the Function Menu......................................39
Function menu operations ................................................................... 39
Function menu settings........................................................................ 39
Handling Discs...............................................................................42
Discs used for recording and playback................................................ 42
Notes on handling................................................................................ 43
Write-protecting discs ......................................................................... 43
Table of Contents 3
Loading and unloading a disc.............................................................. 43
Formatting a disc ................................................................................. 43
Handling Memory Cards ............................................................... 44
About memory cards............................................................................ 44
Handling External Storage............................................................ 45
Using external storage ......................................................................... 45
Removing external storage .................................................................. 46
Chapter 4 Recording, Playback and Copy
Recording....................................................................................... 48
Preparations for recording ................................................................... 48
Carrying out recording......................................................................... 48
Recording with the HDSDI remote control function........................... 49
Continuing recording while exchanging discs (disc exchange cache
function) ..................................................................................... 50
Handling of discs when recording does not end normally (salvage
functions).................................................................................... 50
Playback ......................................................................................... 52
Playback operation............................................................................... 53
Playback operations using thumbnails................................................. 55
Copying .......................................................................................... 56
Overview.............................................................................................. 56
Copy operations ................................................................................... 56
Chapter 5 Operations on Clip List Screens
Overview......................................................................................... 59
Switching between display screens ..................................................... 59
Information and controls on clip list screens....................................... 60
Clip Menu ............................................................................................ 64
Clip F Menu......................................................................................... 64
Clip Operations.............................................................................. 66
Selecting clips...................................................................................... 66
Searching with thumbnails .................................................................. 66
Playing a clip by thumbnail search...................................................... 67
Setting clip flags .................................................................................. 67
Locking (write-protecting) clips .......................................................... 68
Deleting clips ....................................................................................... 68
Copying clips....................................................................................... 69
Setting the index picture frame............................................................ 69
4Table of Contents
EDL Editing ....................................................................................69
What is EDL editing? .......................................................................... 69
Creating and editing EDLs .................................................................. 70
Disc Operations .............................................................................73
Checking the disc information ............................................................ 73
Formatting (initializing) discs ............................................................. 73
Finalizing discs.................................................................................... 73
Repairing discs .................................................................................... 74
Chapter 6 File Operations
Overview.........................................................................................75
Directory structure............................................................................... 75
FTPS protocol support......................................................................... 75
File operation restrictions.................................................................... 76
FTP File Operations.......................................................................79
Making FTP connections..................................................................... 79
Command list ...................................................................................... 80
CIFS File Operations .....................................................................84
Making CIFS connections ................................................................... 84
Chapter 7 Menus
Menu System Configuration .........................................................85
Setup Menu ....................................................................................85
Items in the basic menu ....................................................................... 86
Basic menu operations......................................................................... 89
Menu bank operations (menu items B01 to B13)................................ 91
Items in the extended menu................................................................. 92
Maintenance Menu.......................................................................104
Items in the maintenance menu ......................................................... 104
Maintenance menu operations........................................................... 108
Appendix
Important Notes on Operation....................................................111
About the LCD panel ........................................................................ 111
Condensation ..................................................................................... 112
Periodic Maintenance..................................................................112
Table of Contents 5
Operating hours meter ....................................................................... 112
Troubleshooting .......................................................................... 114
Alarms................................................................................................ 114
Error messages................................................................................... 121
Specifications .............................................................................. 122
Using UMID Data.......................................................................... 126
Ancillary Data............................................................................... 128
Ancillary data in HDSDI/SDSDI signals .......................................... 128
Ancillary data in MXF files............................................................... 128
Closed caption data............................................................................ 129
Trademarks and Licenses .......................................................... 130
Trademarks ........................................................................................ 130
MPEG-4 visual patent portfolio license ............................................ 130
About IJG (Independent JPEG Group).............................................. 130
Character display software “iType”................................................... 130
Open source software licenses........................................................... 130
Obtaining GPL/LGPL/GPL V3 licensed software ............................ 130
Index ............................................................................................ 131
6Features
Chapter 1 Overview
Chapter 1
Overview
Features
The PDW-HD1550 (hereinafter, the “unit”) is a
Professional Disc recorder that supports Full HD (1920 ×
1080) recording on Professional Disc media.
It features enhanced networking and other IT functions,
and is highly compatible with nonlinear editing systems
and network production systems, enabling efficient file-
based operation.
The unit can be used as a player for video editing and
program output, and as a recorder for nonlinear editing.
For these applications, the unit can be connected via its
SDI I/O connectors to earlier nonlinear editors, monitors,
and video equipment with SDI interfaces.
It has a compact, lightweight body for easy portability
outdoors, and can be powered from any of three power
sources: AC, DC, or battery 1) power.
1) BKP-L551 Battery Adaptor is required.
Features of this unit
The principal features of this unit are as follows.
Multiple codecs
MPEG HD422 codec
The MPEG HD422 codec provides video compression
complied with the MPEG-2 422P@HL standard. It enables
HD 4:2:2 (50 Mbps) digital component file recording in
the 1080i (1080 effective scanning lines, interlaced)
format currently in use by many broadcast facilities.
Uncompressed PCM recording of 24-bit 48 kHz audio
enables 8-channel audio recording at high sound quality.
MPEG-4 AVC/H.264 codec 1)
This unit supports the XAVC™ format that complies with
the MPEG-4 AVC/H.264 codec as a recording format and
enables HD 4:2:2 digital component file recording
(CLASS 100) in 1080i (1080 effective scanning lines)
format.
Uncompressed PCM recording of 24-bit 48 kHz audio
enables 8-channel audio recording at high sound quality.
1) Installation of the optional XDBK-106 is required.
Recording to PFD23 Professional Discs is not supported.
Recording and playback functions
Support for MPEG/XAVC/SD with multiple codecs
In addition to the MPEG HD422 codec and XAVC
MPEG-4 AVC/H.264 codec (CLASS 100), this unit
supports the MPEG HD420 codec, allowing HD operation
across a wide range of recording times and application
objectives.
The unit also supports file recording using the DVCAM
codec, and IMX (30/40/50 Mbps) recording and
playback. 1)
1) Playback only for IMX 40 Mbps.
Support for multiple frame frequencies
This unit can record and play MPEG HD422 format video
at frame frequencies of 1080/59.94i, 50i, 29.97P, 25P,
23.98P or 720/59.94P, 50P.
It can record and play XAVC format video at frame
frequencies of 1080/59.94i, 50i, 29.97P, 25P, 23.98P.
SD up-convert function
The unit can output HD signals while playing Professional
Discs recorded as SD, allowing SD material to be utilized
in an HD environment.
HD down-convert function
The unit is provided with a downconvert function. HD
playback signals can be downconverted to SD signals and
then output as SDSDI or composite signals. This allows
you to use SD nonlinear editors and monitors for editing
and program output.
HDSDI remote recording
HDSDI connections can be made to camcorders with
remote HDSDI support (PDW-700 XDCAM HD422
camcorder, HDW-730/730S/750/790/F900R HDCAM
7
Features
Chapter 1 Overview
camcorders) to enable recording synchronized to REC and
STOP operations on the camcorder.
1080/720 cross-conversion
This unit supports cross-conversion output. It can output
720 while playing discs recorded as 1080, and output 1080
while playing discs recorded as 720.
Recording of proxy AV data
Proxy AV data is low-resolution data (1.5 Mbps video, 64
kbps per audio channel) recorded using MPEG-4. When
the unit records high-resolution data, proxy AV data is
generated and recorded simultaneously. Because of its
small size, proxy AV data can be transferred over a
network at high speed, and significantly reduces the
storage capacity required for recording. Various
applications can readily take advantage of these
characteristics, such as editing on laptop computers or
managing content on inexpensive, small-scale servers.
High-speed searches with the jog and shuttle
dials
The jog and shuttle dials can be used to find scenes inside
clips, in the same way as the jog and shuttle dials on
conventional VTRs.
In jog and variable modes, frame advance search in field
units is supported at up to –2 to +2 times normal speed. In
shuttle mode, you can perform high-speed searches at up
to ±20 times normal speed. High-speed F.FWD and
F.REV searching is possible at ±50 times normal speed.
Convenient playback and searching
Like previous products in the XDCAM series, this unit
supports a number of convenient search functions,
including, thumbnail searches, essence marks searches,
and expand searches.
Thumbnail searches: The unit creates thumbnails from
the first frame of each generated clip, and displays
them in thumbnail lists on the color LCD or an
external monitor. You can cue up clips very easily
simply by selecting them from thumbnail lists.
Essence mark searches: Essence marks can be added to
any scene during or after recording. A list of frames
with essence marks can be displayed on the color
LCD or an external monitor.
Expand searches: This function allows you to look inside
the clip selected on a thumbnail screen, or inside the
segment from a selected essence mark to the next
essence mark. The selection range is divided into 12
equal blocks, and the first frames of those blocks are
displayed as thumbnails. By checking the thumbnails,
you can easily find the scene you want.
Usability features
AC, DC, and battery 1) power support
The unit can be used even where AC power is not
available, for example outdoors or in cars or helicopters. 2)
1) BKP-L551 Battery Adaptor is required.
2) When installing the unit, check that the unit can record and play back
normally before use.
When recording/playing XAVC, use the unit under stable conditions with
no vibration.
Color LCD display
The unit is equipped with a 16:9, 4.3-inch color LCD
which allows you to check the contents of the disc and use
the menu system without connecting an external monitor.
Built-in speakers
The unit features built-in speakers, allowing you to
monitor recorded audio. You can check your clips and
editing results using the color LCD and speakers even
when no monitors or separate speakers are available.
Tiltable front panel
The front panel is tiltable for easy rack-mount and desktop
operation. You can adjust the panel to the angle that makes
the buttons easiest to use.
Cache recording for seamless disc exchanges
When recording is in progress, video and audio data can be
recorded to the unit’s internal memory cache during a disc
exchange (up to about 50 seconds can be cached, including
the time it takes to eject and insert the discs), and then
written back to the newly loaded disc. This allows
seamless recording across extended recording sessions,
including recording of video feeds, with no important
scenes lost while discs are being exchanged.
IT friendly
Equipped with network connector
The unit features a Gigabit Ethernet connector as standard
equipment. Via this connector, you can connect the unit to
computers and networks to enable listing of the video,
audio, and metadata files recorded on the Professional
Disc, and rapid file transfers. Support for FTP commands
makes it easy to carry out network file transfers from
remote locations.
Supports SNMP for maintenance and service
This unit supports Sony’s SNMP-based remote
maintenance and monitoring software. This software
allows you to monitor the status of the hardware via a TCP/
IP network in real time, and to record the results in a status
log.
Supports a variety of interfaces
This unit supports the following input/output signals.
• HDSDI video, 8-channel audio input and output
• SDSDI video, 8-channel audio input and output
(the SD/HDSDI INPUT connector doubles as an
SDSDI/HDSDI input connector)
8Features
Chapter 1 Overview
• HDMI output
• SD composite output
• Analog audio 4-channel input
• Analog audio 2-channel output
• AES/EBU digital audio 4-channel input and output
•Remote
- RS-422A (D-sub 9-pin × 1)
Copying files between USB external
storage and a Professional Disc
The unit is provided with a USB 3.0 interface on the front
panel, allowing you to connect a USB mass storage class
(3 GB to 2 TB) device and use it as external storage. You
can copy clips and clip lists between this external storage
and a disc.
You can also copy clips from SxS memory cards by
connecting the optional SBAC-US20/US30 SxS Memory
Card USB Reader/Writer.
Software Downloads
When the unit is used with a PC connection, download any
device drivers, plug-ins, and application software you
require from the following websites.
Sony Professional products website:
U.S.A. http://pro.sony.com
Canada http://www.sonybiz.ca
Latin America http://sonypro-latin.com
Europe http://www.pro.sony.eu/pro
Middle East, Africa http://sony-psmea.com
Russia http://sony.ru/pro/
Brazil http://sonypro.com.br
Australia http://pro.sony.com.au
New Zealand http://pro.sony.co.nz
Japan http://www.sonybsc.com
Asia Pacific http://pro.sony-asia.com
Korea http://bp.sony.co.kr
China http://pro.sony.com.cn
India http://pro.sony.co.in
9
System Configurations
Chapter 1 Overview
System Configurations
a) For HDW-2000 series only.
PDW-700/PMW-500
RM-280 Editing
Controller
BVE-700
Headphones
HDW-2000 series
PDW-F75
Professional Disc
PDW-F1600
BP-FL75/FLX75 Battery
Pack
BKP-L551 Battery
Adaptor
DC power source
AC power source
SD video monitor
HD video monitor
Audio monitor
Laptop computer
The unit can function as a player only when performing linear editing.
10 Front Panel
Chapter 2 Names and Functions of Parts
Chapter 2
Names and Functions of
Parts
Front Panel
The names and symbols of buttons and knobs on the front
panel are color coded according to function.
White: Function when the button or knob is operated
independently.
Orange: Function when the button is operated with the
SHIFT button held down.
Blue: Function related to thumbnail operations.
aOn/standby (1) button and indicator
When the POWER switch on the rear panel is in the @ (on)
position, or when DC power is connected to the DC IN
12V connector on the rear panel, this switches the unit
between the operating state (the indicator is lit green) and
the standby state (the indicator is lit red).
When you press this button with the indicator lit red and
hold it down for a short time (0.25 seconds or longer), the
indicator changes to lit green, and the unit enters the
operating state.
When you press this button with the indicator lit green and
hold it down for a longer time (1 second or longer), the
indicator changes to flashing green and then lit red, and the
unit enters the standby state.
When using this unit, normally leave the rear panel
POWER switch in the @ position, and use this button to
switch the unit between the operating state and standby
state.
1On/standby button and
indicator
2Audio level adjustment
section (see page 11)
2Remote control switch
3KEY INHI switch
4PHONES jack
5LEVEL adjustment knob
6Recording and playback control section (see page 14)
Handle
1Disc control section
(see page 11)
3Arrow buttons
(see page 12)
4Shuttle/jog/variable
control section (see
page 12)
5Display/menu control
section (see page 13)
6Super Speed USB connector
11
Front Panel
Chapter 2 Names and Functions of Parts
bRemote control switch
Different positions of the switch allow different operations
as follows.
NET: Enables access to the network. When an external
network device is being accessed, operations of the
buttons and dials related to recording and playback
are disabled.
LOCAL: Enables operation from the front panel.
With this unit accessing a network device, setting the
remote control switch to “LOCAL” displays a dialog
asking for your confirmation about network
disconnection. To disconnect, press the PUSH SET
knob. To not disconnect, set the remote control switch
to “NET”.
REMOTE: Enables remote control of this unit from the
following devices:
• Devices connected to the REMOTE (9P) connector
• Devices connected to the SD/HDSDI INPUT
connector with SDI remote control functions
Use setup menu item 214 REMOTE INTERFACE to
select which of the connectors is used for remote
control.
When operating the unit by remote control, you can
use setup menu item 006 LOCAL FUNCTION
ENABLE to enable or disable the buttons and switches
in the recording and playback control section of the
unit.
cKEY INHI switch
This turns key operation inhibit mode on or off.
ON: Turns key operation inhibit mode on.
OFF: Turns key operation inhibit mode off.
dPHONES jack
The jack is a standard stereo jack. Connect stereo
headphones to monitor the audio during recording,
playback, and editing. (Non-audio signals are muted.) The
monitored channel is selected with MONITR L and
MONITR R on the HOME page of the function menu (see
page 40).
eLEVEL (volume) adjustment knob
Adjust the volume of headphones or speakers with the
knob. You can also cause this to simultaneously adjust the
output volume from the AUDIO MONITOR R, L
connectors on the rear panel. To do this, set setup menu
item 114 AUDIO MONITOR OUTPUT LEVEL to
“variable”.
fSuper Speed USB connector (USB 3.0)
Connect the USB connector of the external storage device.
1Disc control section
aACCESS indicator
This lights when the Professional Disc is accessed.
While the ACCESS indicator is lit, do not turn off the
POWER switch on the rear panel or disconnect the power
cord.
This could lead to a loss of data from the disc.
bDISC IN indicator
This lights when a Professional Disc is inserted.
cDisc slot
Insert a Professional Disc in this slot.
dEJECT/USB DRV OFF (USB drive off) button
Functions as the EJECT button or the USB DRV OFF
button.
EJECT button: To remove the Professional Disc, press
this button.
USB DRV OFF button: To unmount the USB drive, press
this button.
See “Handling Discs” (page 42) for more information
about disc operations.
See “Handling External Storage” (page 45) for more
information about USB drive operations.
2Audio level adjustment section
Note
1 ACCESS indicator
2 DISC IN indicator
3 Disc slot
4 EJECT/USB DRV OFF
button
REC
NET
REMOTE
LOCAL
VARIABLE KEY INHI
PRE-
SET
ON
OFF
PB
CH-1
ALL CH
CH-2
CH-3
CH-4
1 CH-1/ALL CH, CH-2 to CH-4 adjustment knobs
2 VARIABLE switch
12 Front Panel
Chapter 2 Names and Functions of Parts
aCH-1/ALL CH, CH-2 to CH-4 (audio level)
adjustment knobs
Depending on the setting of the VARIABLE switch, these
adjust the input audio or playback audio levels of channels
1 to 4.
You can adjust levels of channels 5 to 8 using the function
menu.
For details, see page 41.
By setting setup menu item 131 AUDIO VOLUME, you
can enable the CH-1/ALL CH adjustment knob to
simultaneously adjust all eight channels. When this
simultaneous adjustment is enabled, the ALL CH indicator
lights.
bVARIABLE (audio level adjustment selector)
switch
This selects whether the input audio level or playback
audio level is adjusted when using the CH-1/ALL CH and
CH-2 to CH-4 adjustment knobs to adjust channels 1 to 4,
and when using the function menu to adjust channels 5 to
8.
REC: Adjust the input audio levels. The playback audio
levels are fixed at their preset values.
PRESET: The audio levels are fixed at their preset values.
PB: Adjust the playback audio levels. The input audio
levels are fixed at their preset values.
3Arrow buttons
The four arrow buttons can also be used as the MARK1
button, MARK2 button, IN button, and OUT button. The
correspondence with these buttons is as follows.
V button: MARK1 button
v button: MARK2 button
B button: IN button
b button: OUT button
You can use these buttons for thumbnail selection, menu
setting operations, setting IN/OUT points, and so on.
aV/MARK1 button and v/MARK2 button
When the clip list screen is shown on the display, you can
use these for thumbnail selection.
During recording or playback, a shot mark 1 or shot mark
2 is recorded as an essence mark when you press the PUSH
SET knob with the V/MARK1 or v/MARK2 button held
down.
You can delete essence marks on the chapter thumbnail
screen (see page 67).
bIN indicator and OUT indicator
Lights or flashes as follows when you set IN and OUT
points in the clip to copy only the part defined by the IN
and OUT points (see page 57).
IN indicator: When an IN point is set, this lights. If an
attempt is made to set the IN point after a recorded
OUT point, this flashes.
OUT indicator: When an OUT point is set, this lights. If
an attempt is made to set the OUT point before a
recorded IN point, this flashes.
cB/IN button and b/OUT button
When the clip list screen is shown on the display, you can
use these for thumbnail selection.
An IN or OUT point is set when you press the PUSH SET
knob with the B/IN or b/OUT button held down. The IN
or OUT point setting is deleted when you press the
RESET/RETURN button with the B/IN or b/OUT button
held down.
4Shuttle/jog/variable control section
aSHTL/JOG (shuttle/jog)/FOLDER SEL (folder
select) button
Functions as the SHTL/JOG button or the FOLDER SEL
button.
SHTL/JOG button: Press this button, turning it on, to
perform shuttle or jog playback.
FOLDER SEL button: When a USB drive is connected,
press this button to display a list of the folders on the
USB drive.
bVAR/JOG (variable/jog)/MEDIA SEL (media
select) button
Functions as the VAR/JOG button or the MEDIA SEL
button.
VAR/JOG button: Press this button, turning it on, to
perform variable or jog playback.
MEDIA SEL button: When a USB drive is connected,
press this button to select the target media (disc or
USB drive).
MARK2
MARK1
IN OUT
L/JOG
1 V/MARK1 button and v/MARK2 button
2 IN indicator and OUT indicator
3 B/IN button and b/OUT button
RETURN
RESET
1SHTL/JOG)/FOLDER SEL button
2VAR/JOG/MEDIA SEL button
3Jog/shuttle transport indicators
5Jog dial
4Shuttle dial
13
Front Panel
Chapter 2 Names and Functions of Parts
cJog/shuttle transport indicators
These show the playback direction in jog, shuttle, or
variable mode.
dShuttle dial
Turn this dial for shuttle or variable playback.
eJog dial
Turn this dial for jog playback.
For details of playback operations in jog, shuttle, or
variable mode, see “Playback operation” (page 53).
For details of USB drive operations with the FOLDER
SEL and MEDIA SEL buttons, see “Handling External
Storage” (page 45).
5Display/menu control section
aFunction buttons (F1 to F6)
These buttons are enabled when the function menu (see
page 39) is visible. Each press of a button changes the
setting of the corresponding item in the menu.
For convenience, this manual refers to these buttons as
buttons F1 to F6, in order from the top.
bDisplay
Displays menus, audio level meters, and data, such as time
data or clip information. The DISPLAY button lets you
switch to the video monitor display.
For details, see “Display screen” (page 15).
cPUSH SET knob
Use for setting menu items and for operations using
thumbnails on clip list screens. Turn the knob to select
items, and press it to confirm the selection. This button is
also used to set numerical values, such as timecodes.
See “Clip Operations” (page 66) for more information
about how to use the thumbnail screens.
dMENU button
Displays the setup menu or the clip list screen menu. The
setup menu appears when no clip list screen is visible. The
same information is also superimposed on the display on a
monitor connected to the HDMI OUT connector of the
unit. Press once more to return to the original display.
See “Clip Operations” (page 66) for more information
about how to use the thumbnail screens.
eRESET/RETURN button
Functions as the RESET button or the RETURN button.
RESET button: Resets counters or the setting values of
the timecode generator. This button is also used to
abort or cancel setup menu and thumbnail search
operations.
RETURN button: On setup menu and clip list screens,
returns to the previous procedure.
fCOPY button
Displays the Clip Copy screen (see page 56) when pressed
while the clip list screen is shown on the display.
gTHUMBNAIL button
When this button is pressed when the basic operation
screen or video monitor screen is displayed, a list of clips
or EDLs saved on the currently selected media is
displayed. (That is, the current screen is switched to a clip
list screen.) When pressed again, returns to the basic
operation screen or the video monitor screen.
See “Clip Operations” (page 66) for more information
about how to use the thumbnail screens.
hDISPLAY button
Each press of this button switches the display screen
between the basic operation screen and video monitor
screen (see page 15).
When the clip list screen is shown on the display, this
button switches the display screen between thumbnails
view and details view.
iSHIFT button
Switches between functions for any button with two
functions.
1Function buttons (F1 to F6)
2Display
3PUSH SET knob
4MENU button
5RESET/RETURN button
7THUMBNAIL button
6COPY button
8DISPLAY button
9SHIFT button
0PAGE/HOME button
14 Front Panel
Chapter 2 Names and Functions of Parts
jPAGE/HOME button
When pressed alone, this functions as the PAGE (page
switching) button. When pressed together with the SHIFT
button, functions as the HOME button.
PAGE button: Displays the function menu, if it is not
already visible. (The most recently displayed page of
the function menu appears.)
HOME button: When pressed with the function menu
visible, returns to the HOME page of the function
menu.
6Recording and playback control section
aPREV (previous) button
Press this button, turning it on, to show the first frame of
the current clip. When the first frame of a clip is shown,
pressing this button jumps to the beginning of the previous
clip. 1) This button is also used together with other buttons
for the following operations.
Reverse direction high-speed search: Hold down the
PLAY button, and press this button. A high-speed
search in the reverse direction is carried out.
Displaying the first frame of the first clip: Hold down
the SHIFT button, and press this button.
1) When setup menu item 153 FIND MODE is set to “clip & rec start mark”,
this button jumps to the frame where the previous Rec Start essence mark
is set and displays the video of that frame.
bPLAY button
To start playback, press this button, turning it on.
When this button is pressed during recording, recording
stops and the unit enters stop mode. If you do not want to
stop recording when this button is pressed, set setup menu
item 145 MODE KEY ENABLE DURING RECORDING
to “stop”.
cNEXT button
Press this button, turning it on, to jump to the next clip, and
show the first frame. 2) This button is also used together
with other buttons for the following operations.
Forward direction high-speed search: Hold down the
PLAY button, and press this button. A high-speed
search in the forward direction is carried out.
Displaying the last frame of the last clip: Hold down the
SHIFT button, and press this button.
2) When setup menu item 153 FIND MODE is set to “clip & rec start mark”,
this button jumps to the frame where the next Rec Start essence mark is set
and displays the video of that frame.
dSTOP button
To stop recording or playback, press this button, turning it
on. The frame at the stop point is displayed.
This button flashes when setup menu item 105
REFERENCE SYSTEM ALARM is set to “on” and the
correct reference video input signal (as specified by OUT
REF on the HOME page of the function menu) is not being
input.
eREC (record) button
To start recording, hold down this button, and press the
PLAY button. The recording takes place on an unrecorded
part of the disc.
To stop recording, press the STOP button.
To monitor in EE mode
You can press this button when in stop mode to monitor
input signals in EE mode. The button lights when pressed.
Press the STOP button to return to the original video.
You can also press this button during playback and
searches to view EE mode for as long as the button is held
down.
fREC INHI (recording inhibit) indicator
This lights in the following cases.
• When a disc with recording inhibited is loaded.
• When the format of the recorded part of the disc does not
match the system frequency settings of the unit.
gSTANDBY indicator
Lights when the unit is put into disc stop mode. After a
certain time passes in a disc stop mode, the unit
automatically enters standby state and the indicator goes
off.
You can specify the time until the unit enters standby state
with setup menu item 501 STILL TIMER.
TOP F REV END REC INHI
F FWD
PREV PLAY STOPNEXT REC
1PREV button
2PLAY button
3NEXT button
4STOP button
5REC button
7STANDBY indicator
6REC INHI indicator
Note
15
Front Panel
Chapter 2 Names and Functions of Parts
Display screen
Basic operation screen
aFunction menu
Use the PAGE/HOME button to display this menu, and to
switch between the pages (HOME, P1 to P5, P61), and
HOME21)) of the menu. Each page has one to six setting
items. Press the corresponding function button to change a
setting.
For details, see “Basic Operations of the Function Menu”
(page 39).
1) Displayed only when maintenance menu item M38 F-KEY CONFIG is
configured.
bAudio input display/audio level meters
Displays information about audio. There are two display
modes for the audio level meter: FULL mode and FINE
mode, which can be switched using AU METER on page
P3 AUDIO of the function menu.
1 Function menu
2 Audio input display/audio level meters
3 System information
4 Disc status indicator
5 Recording/playback format
6 Clip information
7 Status indicator
8 Time data display area
9 Status display area
AInput signal indicator
BData indicator
DAudio channel
EReference level
FLevel bars
CMonitor channel
Meter display mode: FINEMeter display mode: FULL
GMeter display mode
16 Front Panel
Chapter 2 Names and Functions of Parts
AInput signal indicator: Displays the audio input
signal.
.
a) When maintenance menu item M374 ANALOG I/O is set to “4ch”
only.
BData indicator: Appears when the input signals are
non-audio signals.
CMonitor channel: Displays the audio monitoring
channels set with MONITR L and MONITR R on the
HOME page of the function menu (see page 40).
DAudio channel: Displays the audio channels.
Also indicates preset or variable-speed mode by its
color (see page 12).
White: Preset mode
Green: Variable-speed mode
EReference level: Displays the reference level for
recording as set with maintenance menu item M370
HEAD ROOM.
For details on setting the reference level, see
maintenance menu item M37 (page 105).
FLevel bars: Displays the audio recording or playback
levels of channels 1 to 8. The OVER indicators light
when the audio level exceeds 0 dB.
GMeter display mode: Displays the audio level meter
display mode selected with AU METER on page P3
AUDIO of the function menu (see page 41).
cSystem information
AReference signal: Displays the type of reference
signal to which this unit is synchronizing.
When there is no display, the unit is synchronizing to
the internal reference signal.
INPUT: Input video
HD REF: HD-format reference signal
SD REF: SD-format reference signal
BVideo input indicator: Displays the selected video
input signal.
HD-SDI: HDSDI video input
SD-SDI: SDSDI video input
SG: Test video signal from the internal signal
generator
The video signal input is selected with V INPUT on
page P1 INPUT of the function menu (see page 40).
The display blinks when there is no video input signal,
and when the video input signal does not match the
system frequency of this unit.
dDisc status indicator
Displays an icon indicating the status of the disc or
external storage.
The PFD128QLW disc status indicator changes with the
remaining capacity of the recordable resource space (for
writing the disc management data, etc.).
Display Input signal
ANA-1
(MIC-1)
Analog audio signal Channel 1, 3, 5, 7 or
Channel 1, 5 a)
ANA-2
(MIC-2)
Channel 2, 4, 6, 8 or
Channel 2, 6 a)
ANA-3 Channel 3, 7 a)
ANA-4 Channel 4, 8 a)
HD-SDI HDSDI audio signal (flashes when there is
no input signal)
SD-SDI SDSDI audio signal (flashes when there is no
input signal)
AES/
EBU
AES/EBU audio signal (flashes when there is
no input signal)
SG Test signal from the internal signal generator
A Reference signal
B Video input indicator
Note
Icon Status
Professional Disc
PFD23A/
PFD50DLA/
PFD100TLA
PFD128QLW External
storage
Not loaded
— Mounting
Displays a
mounting progress
bar.
Normal status
Warning level error
has occurred.
(Finalizing is not
possible.)
Error has occurred.
(Restoring is not
possible.)
— — Finalized
— Ejecting
17
Front Panel
Chapter 2 Names and Functions of Parts
The remaining capacity of recordable resource space is not
the same as the remaining recording capacity. When there
is no available recording resource space left on the disc,
file writing may be disabled even with sufficient available
storage remaining.
eRecording/playback format
This displays the recording format during recording and
the playback clip format during playback.
fClip information
Displays clip information.
gStatus indicator
Displays icons indicating the status of this unit.
hTime data display area
ARemaining disc capacity for recording or
playback: Displays the amount of remaining capacity
for recording or playback on the disc.
BREC RUN/FREE RUN: Displays the timecode run
mode. The run mode is set with RUN MODE on page
P4 TC of the function menu (see page 41).
CTimecode generator mode: Displays the timecode
source and generation method (preset or regenerate).
These are set with TCG and PRST/RGN on page P4
TC of the function menu (see page 41).
DVITC: Lights in the following cases.
• When VITC is read in playback mode. (This has no
relation to the display in the time data display area.)
• When VITC recording is possible.
ETime data type: Displays the type of time data
displayed in the time data display area. The type of
time data is selected with CNTR SEL on the HOME
page of the function menu (see page 39).
FTime data: Normally displays timecode or VITC,
according to the selection made with TCR on page P4
TC of the function menu.
GDF/NDF indicator: Displays the frame count mode
for the internal timecode reader (TCR) and internal
timecode generator (TCG). The frame count mode is
Icon Status
The available recordable resource space is
running out.
There is no available recordable resource
space on the disc.
Note
Icon Description
Currently set to repeat playback mode
Currently set to single clip playback mode
Currently set to single clip playback mode with
repeat playback mode
1080/720 cross-convert output
Recording
Yellow bar
Red bar
Codec
Video format
System frequency
Audio format
Clip name
Clip number/total number of clips
Duration
Clip format
(Codec, video format, system frequency,
audio format)
Display Type of time data
TC Timecode
COUNTER Elapsed recording/playback time
UB User bits
VITC VITC
VIUB VIUB
TCG Timecode generator value
UBG User bits generator value
A Remaining disc capacity for recording or playback
B REC RUN/FREE RUN
C Timecode generator mode
E Time data type
F Time data
GDF/NDF
indicator
(TCG)
D VITC
GDF/NDF
indicator
(TCR)
HRecording
mode
indicator
18 Front Panel
Chapter 2 Names and Functions of Parts
set with DF/NDF on page P4 TC of the function menu
(see page 41).
H Recording mode indicator: This appears when setup
menu item 150 REC MODE is set to “disc exchange
cache”.
iStatus display area
AError, warning, and alarm messages: Messages
about operations and the status of the unit appear here.
The seriousness of the message is indicated by the
color, as follows.
Red: Error message (flashing)
Orange: Warning message
White: Alarm message
BDelete icon: Flashes while a clip deletion is being
executed.
CCopy icon: During a clip copy operation, displays an
icon indicating the copy source/copy destination
media.
DNetwork connection indicator: Lights while data is
being exchanged with a network connected external
device.
ENetwork remote connection indicator: “NET-
RMT” or “RM-SDI” is displayed during a network
remote control connection to an external device (see
page 49).
FMenu setting status: Displays the current setup menu
settings.
GPower source indicator: Displays the icon for the
power source being used.
When the remaining battery power drops below a
certain level, the battery icon starts flashing (this is the
battery near end alarm).
With the battery near end alarm displayed, when the
battery voltage drops below the shutdown voltage set
with setup menu item 033 BATTERY END
VOLTAGE, the unit is automatically shut down.
Video monitor screen
A Audio level meters: LEVEL MT on page P3 AUDIO
of the function menu determines whether the meter is
to be displayed and on which side, left or right, in the
display window.
BSuperimposed information: Appears when CHAR
SEL on the HOME page of the function menu is set to
“ON”.
CStatus display area: Displays messages and icons
about the status of the unit (see page 18).
Display Frame count mode
.DF (drop-frame mode)
:NDF (non-drop-frame mode)
Icon Copy source/copy destination media
External storage/disc
Disc/external storage
Memory card/disc
Disc/memory card
A Error, warning, and alarm messages
B Delete icon
D Network connection indicator
E Network remote connection indicator
F Menu setting status
C Copy icon
G Power source indicator
Display Current setup menu settings
BANK1 Same as those in menu bank 1.
BANK2 Same as those in menu bank 2.
BANK3 Same as those in menu bank 3.
DEFAULT Same as the factory default settings.
Nothing
displayed
Different from any of the above.
Icon Power source being used
AC power source
Battery
Note
A Audio level meters
C Status display area
B Superimposed information
19
Front Panel
Chapter 2 Names and Functions of Parts
You can disable the status display area with the
DISPLAY button. However, it is automatically
enabled when:
• Display of error/warning/alarm message becomes
necessary.
• During battery-driven operation, the power source
indicator starts flashing (the battery near end alarm
is given).
20 Rear Panel
Chapter 2 Names and Functions of Parts
Rear Panel
aSD/HDSDI INPUT (SDSDI/HDSDI signal input)
connector (BNC type)
This inputs an SDSDI or HDSDI format video/audio
signal.
bHDSDI OUTPUT 1, 2 (SUPER) (HDSDI signal
output 1, 2 (superimpose)) connectors (BNC type)
These output HDSDI format video/audio signals.
You can superimpose timecodes or other information on
the output of the HDSDI OUTPUT 2 (SUPER) connector
using the CHAR SEL setting on the HOME page of the
function menu or the setting for setup menu item 028 HD
CHARACTER. You can always disable the
superimposition of data independently of the setting for
CHAR SEL using the setting for setup menu item 028.
See “Basic Operations of the Function Menu” (page 39)
for more information about the CHAR SEL setting.
See page 88 for more information about the setup menu
item 028 HD CHARACTER.
To treat the input and output signals of these connectors as
non-audio signals, set maintenance menu item M372
NON-AUDIO INPUT.
For details, see maintenance menu item M37 (page 105).
cSDSDI OUTPUT 1, 2 (SUPER) (SDI signal outputs
1, 2 (superimpose)) connectors (BNC type)
These output SDSDI format video/audio signals.
When the unit is shipped from the factory, audio signal
output is eight channels with no switching, and RP188
timecode output is set to on. You can change these settings
with setup menu item 828 SDI AUDIO OUTPUT
SELECT and setup menu item 920 SD-SDI H-ANC
CONTROL.
The output from the 2 (SUPER) connector can have
timecode and other text information superimposed. To
turn superimposition off, set CHAR SEL on the HOME
page of the function menu to “OFF”.
See “Items in the extended menu” (page 92) for more
information about setup menu settings.
See “Basic Operations of the Function Menu” (page 39)
for more information about the CHAR SEL setting.
dREMOTE (9P) (remote control 9-pin) connector
(D-sub 9-pin)
Connect a controller that supports the RS-422A Sony 9-pin
VTR control protocol.
eHDMI OUT connector
Connects to an HD projector, HD television, or other HD
consumer device, and outputs digital signals (video, audio,
and control signals).
1Power supply section
(see page 21)
2Analog audio signal input/
output section (see page 21)
5HDMI OUT connector
4REMOTE (9P) connector
6DC IN 12V connector
7REMOTE connector
2
HDSDI OUTPUT 1, 2
(SUPER) connectors
8COMPOSITE OUTPUT 1, 2
(SUPER) connectors
9REF. VIDEO INPUT
connectors
4Timecode input/output
section (see page 22)
qa MAINTENANCE connectors
3SDSDI OUTPUT 1, 2 (SUPER)
connectors q; (network) connector
1SD/HDSDI INPUT
connector
3Digital audio signal input/
output section (see page 22)
21
Rear Panel
Chapter 2 Names and Functions of Parts
The audio signals of the channels selected with MONITR
L and MONITR R on the HOME page of the function
menu are output.
You can superimpose timecodes, menu settings, and error
messages on the HDMI output using the CHAR SEL
setting on the HOME page of the function menu.
See “Basic Operations of the Function Menu” (page 39)
for more information about the MONITR L and
MONITR R settings.
fDC IN 12V connector (XLR 4-pin, male)
Connect to a 12 V DC power source.
When using the BKP-L551 Battery Adaptor to mount a
battery pack, connect the power cable of the BKP-L551.
For details, see “Supplying power” (page 23).
gREMOTE connector (4-pin)
Supplies power to the RM-280 Remote Edit Controller.
hCOMPOSITE OUTPUT 1, 2 (SUPER) (analog
composite video output 1, 2 (superimpose))
connectors (BNC type)
These output analog composite video signals. You can
superimpose timecodes on the output of the 2 (SUPER)
connector when CHAR SEL on the HOME page of the
function menu is set to ON.
See “Basic Operations of the Function Menu” (page 39)
for more information about the CHAR SEL setting.
iREF. VIDEO INPUT (reference video signal input)
connectors (BNC type)
The two connectors form a loop-through connection; when
a reference video signal is input to the left connector, the
same signal is input from the right connector ( ) (IN)
to a connected device. When no connection is made to the
right connector, the left connector is automatically
terminated with an impedance of 75 ohms.
j (network) connector (RJ-45 type)
This is a 10BASE-T/100BASE-TX/1000BASE-T
connector for network connection.
• For safety, do not connect the connector for peripheral
device wiring that might have excessive voltage to this
port. Follow the instructions for this port.
• When you connect the network cable of the unit to
peripheral device, use a shielded-type cable to prevent
malfunction due to radiation noise.
kMAINTENANCE connectors
These are High Speed USB (USB2.0) connectors for
maintenance.
Do not use for applications other than maintenance.
1Power supply section
aPOWER (main power) switch
Press the : side to power on the unit. Press the a side to
power off.
When using the unit, normally leave the POWER switch in
the : (on) position, and use the on/standby button on the
front panel to switch the unit between the operating state
and standby state.
Before turning the main power off, always check to be sure
that the unit is in the standby state, and then press the main
power switch to the a side.
b-AC IN connector
Connect to an AC power source using a power cord (not
supplied).
2Analog audio signal input/output section
aANALOG AUDIO INPUT 1, 2 connectors (XLR
3-pin, female)
These input analog audio signals.
With A1 INPUT, A2 INPUT, A3 INPUT, and A4 INPUT
on page P1 INPUT of the function menu (see page 40),
you can assign the input signal on connector 1 to audio
channel 1 or 3, and assign the input signal on connector 2
to audio channel 2 or 4.
With A5 INPUT, A6 INPUT, A7 INPUT, and A8 INPUT
on page P2 INPUT of the function menu (see page 40),
you can assign the input signal on connector 1 to audio
channel 5 or 7, and assign the input signal on connector 2
to audio channel 6 or 8.
You can set the reference input level with maintenance
menu item M373 IN LEVEL. (Factory default setting:
+4dB)
For details, see maintenance menu item M37 (page 105).
CAUTION
Note
1POWER switch
2- AC IN connector
ANALOG AUDIO INPUT ANALOG AUDIO OUTPUT
1212
AUDIO MONITOR
RL
1ANALOG AUDIO INPUT 1, 2 connectors
2ANALOG AUDIO OUTPUT 1, 2
connectors
3AUDIO MONITOR R, L connectors
22 Rear Panel
Chapter 2 Names and Functions of Parts
Microphone settings
If you have connected a microphone to this unit, you can
set input level, AGC, and limiter values for the
microphone with setup menu items 834, 839, 840, and 841.
An unpleasant sound may be output if you have connected
a microphone to the ANALOG AUDIO INPUT 1 or 2
connector and power the microphone on with the input
level too high. Check the input level setting before
connecting a microphone.
bANALOG AUDIO OUTPUT 1, 2 connectors (XLR
3-pin, male)
These output analog audio signals.
When the unit is shipped from the factory, connector 1 is
set to audio channel 1, and connector 2 is set to audio
channel 2. You can change these settings with setup menu
item 824 ANALOG LINE OUTPUT SELECT (see
page 100).
You can set the output level with maintenance menu item
M377 OUT LEVEL. (Factory default setting: +4dB)
Non-audio signals are muted.
For details, see maintenance menu item M37 (page 105).
The function of the ANALOG AUDIO OUTPUT 1, 2
connectors can be switched to ANALOG AUDIO INPUT
3, 4 connectors with maintenance menu item M374
ANALOG I/O.
With A1 INPUT, A2 INPUT, A3 INPUT, and A4 INPUT
on page P1 INPUT of the function menu (see page 40),
you can assign the input signal on connector 1 to audio
channel 1, the input signal on connector 2 to audio channel
2, the input signal on connector 3 to audio channel 3, and
the input signal on connector 4 to audio channel 4.
With A5 INPUT, A6 INPUT, A7 INPUT, and A8 INPUT
on page P2 INPUT of the function menu (see page 40),
you can assign the input signal on connector 1 to audio
channel 5, the input signal on connector 2 to audio channel
6, the input signal on connector 3 to audio channel 7, and
the input signal on connector 4 to audio channel 8.
To use ANALOG AUDIO OUTPUT connectors as
ANALOG AUDIO INPUT connectors, XLR male-to-
female adaptors are required.
The ANALOG AUDIO INPUT 3, 4 connectors do not
support microphone connection.
cAUDIO MONITOR R, L connectors (XLR 3-pin,
male)
This outputs an audio signal for monitoring.
The monitored channel is selected with MONITR L and
MONITR R on the HOME page of the function menu.
See “Basic Operations of the Function Menu” (page 39)
for more information about the MONITR L and
MONITR R settings.
3Digital audio signal input/output section
aDIGITAL AUDIO (AES/EBU) IN (digital audio
input) 1/2, 3/4 connectors (BNC type)
These input AES/EBU format digital audio signals.
bDIGITAL AUDIO (AES/EBU) OUT (digital audio
output) 1/2, 3/4 connectors (BNC type)
These output AES/EBU format digital audio signals.
To treat the input and output signals of these connectors as
non-audio signals, set maintenance menu item M372
NON-AUDIO INPUT.
For details, see maintenance menu item M37 (page 105).
4Timecode input/output section
aTIME CODE IN connector (BNC type)
This inputs an SMPTE timecode generated by an external
device.
bTIME CODE OUT connector (BNC type)
This outputs the following timecode, depending on the
operating state of this unit.
During playback: Playback timecode
During recording: The timecode from the internal
timecode generator or the timecode input to the TIME
CODE IN connector
Note
Note
1DIGITAL AUDIO (AES/EBU)
IN 1/2, 3/4 connectors
2DIGITAL AUDIO (AES/EBU)
OUT 1/2, 3/4 connectors
IN OUT
TIME CODE
1TIME CODE IN connector
2TIME CODE OUT
connector
23
Preparing Power Sources
Chapter
Chapter 3 Preparations
3
Preparations
Preparing Power Sources
This unit can be powered by AC power, DC power, or a
battery pack.
For safety, use only the Sony battery packs listed below.
Lithium-ion battery pack: BP-FL75/FLX75
If you load or remove a battery pack incorrectly, it may fall
and cause bodily injury. Follow the procedures described
below to load or remove them.
Supplying power
AC power supply
Connect the AC IN connector to an AC power source using
the specified AC power cord. To supply AC power to the
unit, set the POWER switch on the rear panel to = (on), then
press the on/standby button (1) on the front panel and
hold it down for a short time (0.25 seconds or longer).
DC power supply
Connect the DC IN 12V connector to a DC power source.
To supply DC power to the unit, turn off the POWER
switch on the rear panel, then press the on/standby button
(1) on the front panel and hold it down for a short time
(0.25 seconds or longer). If the POWER switch on the rear
panel is set to = (on), AC power is supplied.
Battery power supply
You can use the BP-FL75/FLX75 Battery Pack with this
unit.
To use the battery pack, a BKP-L551 Battery Adaptor and
a dedicated battery charger are also required.
Continuous recording time at room temperature
BP-FLX75 lithium-ion battery pack: Approx. 55 minutes
(MPEG HD422 format)
For details on charging battery packs, refer to the
operation manual for the battery charger.
Notes about battery usage
• As long as a battery is connected to the unit, electric
current flows in the unit to keep the CPU in the standby
state, when the unit is not turned on. If the unit is not
used for an extended period, remove the battery.
• Before using the batteries, be sure to charge them fully
with the special battery charger. Refer to the operating
instructions for your battery charger for more
information about how to charge the batteries.
• Batteries may not be completely charged if you charge
them immediately after use when they are still warm.
You should wait until the batteries cool before charging
them.
Attaching a battery pack
Use the BKP-L551 in the following way to attach and
remove the BP-FL75/FLX75 Battery Pack.
For details on attaching the BKP-L551, refer to the
installation manual for the BKP-L551.
Batteries shall not be exposed to excessive heat such as
sunshine, fire or the like.
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type
recommended by the manufacturer.
When you dispose of the battery, you must obey the law in
the relative area or country.
Note
WARNING
CAUTION
24 Preparing Power Sources
Chapter 3 Preparations
1
Attach the BKP-L551 to the side panel.
2
Align the grooves on the BP-FL75/FLX75 with the
projections on the BKP-L551.
3
Slide the BP-FL75/FLX75 as shown below so that the
connectors on the BP-FL75/FLX75 and the
BKP-L551 are connected.
4
Connect the DC cable of the BKP-L551 to the DC IN
12V connector.
Removing the battery pack
With the lever pushed in, slide the BP-FL75/FLX75 out as
shown below.
Checking the remaining battery power
You can use the LEDs on the side panel of the battery to
check the remaining power of the battery.
When the remaining battery power decreases substantially
and the voltage approaches the set shutdown voltage, the
power source icon starts flashing in the status display area
of the display screen (the battery near end alarm is given).
BKP-L551
BP-FL75/FLX75
Lever
25
Initial Setup
Chapter 3 Preparations
Initial Setup
This unit is shipped with the system frequency, and current
date and time still unset.
Therefore, you need to make initial setup settings before
using the unit. (You cannot use the unit without setting it
up.)
Once the unit has been set up, the settings are retained even
when the unit is powered off.
Use the following procedures.
1
Power the unit on.
The INITIAL SETUP screen appears on the display.
2
Turn the PUSH SET knob to select the area of use.
Display UC (for regions outside Japan) or J (for
Japan), and then press the SET function button (F5).
The system frequency screen appears.
3
Turn the PUSH SET knob to select the system
frequency.
Display the system frequency that you want to use, and
then press the SET function button (F5).
4
If you want to save the settings made up to this point,
press the SET function button (F5) again.
The message “NOW SAVING...” appears, and the
setting screen disappears. Then the unit powers itself
off and on again.
To return to the original screen without saving
settings
Press the RETURN function button (F1).
To set the date and time
Set maintenance menu item M3D DATE/TIME PRESET.
For details, see maintenance menu item M3D (page 107).
26 Front Panel Tilt Mechanism
Chapter 3 Preparations
Front Panel Tilt
Mechanism
The front panel of this unit has a tilt mechanism that allows
you to pull the front panel out and adjust it to a convenient
angle.
To pull the front panel out
Grasp the holds (small protrusions) on both sides of the
front panel and pull out as indicated by the arrow.
You can fix the angle of the front panel in position 1 (15
degrees) or position 2 (40 degrees).
The angle cannot be fixed if you pull the front panel past
position 2 all the way out to the return position. To fix the
front panel, return it to position 0 and then pull it out to
position 1 or position 2.
To return the front panel to its original
position
Unlock the front panel by pulling it out to the return
position. You can then return it to position 0.
To change the angle of the front panel
To change the angle to position 2 from position 1, pull the
front panel out to position 2.
To change the angle to position 1 from position 2, first
unlock the front panel by pulling it all the way out to the
return position. Then return it to position 0, and pull out
again to position 1.
Note
Return position
Position 2 (40 degrees)
Position 1 (15 degrees)
Position 0
27
Connections and Settings
Chapter 3 Preparations
Connections and
Settings
Production of some of the peripherals and related devices
described in this chapter may have been discontinued.
For advice about choosing devices, please contact your
Sony dealer or a Sony representative.
Connections for Content Browser
and non-Sony nonlinear editors
When using Content Browser, you can gain remote access
to this unit from a network connected computer. You can
also access this unit from a nonlinear editor that is not a
Sony product via FTP/CIFS, and use this unit as a material
server.
For an overview and installation of Content Browser,
access the Sony website closest to your area.
Using the (network) connector (FTP
connection)
The following shows an example of an FTP (File Transfer
Protocol) connection.
The PDW-HD1550 IP address and other network-related
settings are required for connection.
For details on network settings, see M5: NETWORK of the
maintenance menu (page 107).
Connecting a PDW-HD1550 unit directly to a
laptop computer
Connecting three PDW-HD1550 units to a laptop
computer via a LAN
When you connect the network cable of the unit to
peripheral device, use a shielded-type cable to prevent
malfunction due to radiation noise.
Note
Note
PDW-HD1550 (this unit)
To (network) connector
Network cable (not supplied)
Laptop computer
Settings on this unit
Remote control switch: NET (see page 11)
Setup menu item 257 NETWORK ENABLE: network
CAUTION
Settings on all PDW-HD1550 units
Remote control switch: NET (see page 11)
Setup menu item 257 NETWORK ENABLE: network
Network cable
(not supplied)
To (network)
connector
Laptop computer
PDW-HD1550
28 Connections and Settings
Chapter 3 Preparations
Connections for cut editing
The following figure shows a cut editing system
comprising this unit as a player.
When making the connections, also refer to the manuals
provided with the equipment to be connected.
See page 29 for more information about editing control
unit settings.
When using an editing control unit
Using BVE-700/700A
The following figure shows a cut editing system
comprising this unit as a player, an HDW-M2000/M2000P
unit as a recorder, and a BVE-700/700A as an editing
control unit.
IN OUT
IN 1/2 3/4 1/2 3/4
OUT
12 12
21 (SUPER) 21 (SUPER)
REMOTE (9P)
(MAINTENANCE)
12
(SUPER)
IN
REMOTE
12V
RL
TIME
CODE
SD/HDSDI
INPUT
DIGITAL AUDIO
(AES/EBU)
SDSDI OUTPUTHDSDI OUTPUT
ANALOG AUDIO INPUT ANALOG AUDIO OUTPUT AUDIO MONITOR
COMPOSITE OUTPUT REF. VIDEO INPUT
OUT
HD video monitor
To HDSDI input connector
1: 75Ω coaxial cable (not supplied)
2: 9-pin remote control cable (not supplied)
PDW-HD1550
(this unit, player)
Reference video signal
HDW-M2000
(recorder)
To HDSDI
input connector
HD video monitor
BVE-700/700A
(editing control unit)
To HDMI input connector a)
3: HDMI cable (not supplied)
Use of an optional Sony HDMI cable is recommended.
a) You can use setup menu item 161 (see page 94) to
set which signal to output from the HDMI OUT
connector: the same signal as the HDSDI
OUTPUT 2 (SUPER) connector output, or the
HDSDI signal and thumbnails view signal by
automatically switching between them.
or
29
Connections and Settings
Chapter 3 Preparations
Editing control unit settings
When connecting an editing control unit (BVE-700/700A/
2000) to use with this unit, set VTR constants as follows.
.
HDW-M2000 (recorder) settings BVE-700/700A (editing control unit) setting Settings on this unit
REMOTE 1 (9P) button: Lit SYNCHRONIZE menu: OFF Remote control switch:
REMOTE (see page 11)
REF.VIDEO INPUT connector 75 Ω termination
switch: OFF
Setup menu item 214
REMOTE INTERFACE:
9PIN
Audio selection function switching button
INPUT button: HDSDI
Function menu HOME >F1 (VID. IN): SDI
Function menu page 1 >F1 (TCG): INT
Function menu page 1 >F2 (PR/RGN): PRESET
Function menu page 1 >F3 (RUN): FREE
System frequency VTR constant
12 345678910 11 12 13 14 15 16
59.94i/59.94P/29.97P A0 9C 00 96 07 07 03 80 0A 07 FE 00 80 5A FF 5A
50i/50P/25P A19C007D070703800A07FE00804CFF4B
23.98P A2 9C 00 78 07 07 03 80 0A 07 FE 00 80 48 FF 48
30 Connections and Settings
Chapter 3 Preparations
Using RM-280
The following figure shows a cut editing system
comprising this unit as a player, a PDW-F1600 unit as a
recorder, and an RM-280 as an editing controller.
IN OUT
IN 1/2 3/4 1/2 3/4
OUT
12 12
21 (SUPER) 21 (SUPER)
REMOTE (9P)
(MAINTENANCE)
12
(SUPER)
IN
REMOTE
12V
RL
TIME
CODE
SD/HDSDI
INPUT
DIGITAL AUDIO
(AES/EBU)
SDSDI OUTPUTHDSDI OUTPUT
ANALOG AUDIO INPUT ANALOG AUDIO OUTPUT AUDIO MONITOR
COMPOSITE OUTPUT REF. VIDEO INPUT
OUT
HD video monitor
To HDSDI input connector
1: 75Ω coaxial cable (not supplied)
2: 9-pin remote control cable (not supplied)
PDW-HD1550
(this unit, player)
Reference video signal
PDW-F1600
(recorder)
To HDSDI
input connector
RM-280
(editing
controller)
HD video monitor
To HDMI input connector a)
3: HDMI cable (not supplied)
a) You can use setup menu item 161 (see page 94) to
set which signal to output from the HDMI OUT
connector: the same signal as the HDSDI
OUTPUT 2 (SUPER) connector output, or the
HDSDI signal and thumbnails view signal by
automatically switching between them.
Use of an optional Sony HDMI cable is recommended.
or
31
Connections and Settings
Chapter 3 Preparations
Using the editing functions of the recorder (controlling through REMOTE
(9P) connector)
The following figure shows a cut editing system
comprising this unit as a player, and an HDW-M2000/
M2000P unit as a recorder. In this example, video and
audio signals are connected by HDSDI, and control signals
are transferred via the REMOTE (9P) connector.
PDW-F1600 (recorder) settings RM-280 (editing controller) settings Settings on this unit
Remote control switch: REMOTE EDITOR/REMOTE CONTROL selector
switch: EDITOR
Remote control switch: REMOTE
(see page 11)
Setup menu item 214 REMOTE INTERFACE:
9PIN
Setup menu 01 PREROLL: 5s Setup menu item 214 REMOTE
INTERFACE: 9PIN
Function menu page P1 VIDEO >V INPUT: HD
SDI
Setup menu 05 SYNC SEL: ON
Function menu pages P2 and P3 AUDIO >A1 to
A8 INPUT: SDI
Setup menu 06 SYNC VTR:
RECORDER
Function menu page P4 TC >TCG: INT Setup menu 09 EDIT DLY: –7
Function menu page P4 TC >PRST/RGN:
PRESET
Setup menu 10 R ST DLY: AUTO
Function menu page P4 TC >RUN MODE:
FREE RUN
Setup menu 11 P ST DLY: AUTO
IN OUT
IN 1/2 3/4 1/2 3/4
OUT
12 12
21 (SUPER) 21 (SUPER)
REMOTE (9P)
(MAINTENANCE)
12
(SUPER)
IN
REMOTE
12V
RL
TIME
CODE
SD/HDSDI
INPUT
DIGITAL AUDIO
(AES/EBU)
SDSDI OUTPUTHDSDI OUTPUT
ANALOG AUDIO INPUT ANALOG AUDIO OUTPUT AUDIO MONITOR
COMPOSITE OUTPUT REF. VIDEO INPUT
OUT
HD video monitor
To HDSDI input connector
PDW-HD1550
(this unit, player)
Reference video signal
HDW-M2000
(recorder)
To HDSDI input connector
1: 75Ω coaxial cable (not supplied)
2: 9-pin remote control cable (not supplied)
HD video monitor
To HDMI input connector a)
3: HDMI cable (not supplied)
a) You can use setup menu item 161 (see page 94) to set
which signal to output from the HDMI OUT
connector: the same signal as the HDSDI OUTPUT 2
(SUPER) connector output, or the HDSDI signal and
thumbnails view signal by automatically switching
between them.
or
Use of an optional Sony HDMI cable is recommended.
32 Connections and Settings
Chapter 3 Preparations
For details of HDW-M2000/M2000P settings, refer to the
HDW-M2000/M2000P Operation Manual.
Connections for pool coverage
The following figure shows an example of connections for
pool coverage, with the PDW-700 Professional Disc
Camcorder connected.
HDW-M2000 (recorder)
setting
Settings on this unit
REMOTE 1 (9P) button:
Unlit
Remote control switch:
REMOTE (see page 11)
Setup menu item 214
REMOTE INTERFACE: 9PIN
75Ω coaxial cable (not supplied)
To SDI OUT 1 connector
PDW-700 PDW-HD1550 (this unit)
To SD/HDSDI INPUT
connector
PDW-700 (camcorder)
setting
Settings on this unit
HDSDI REMOTE I/F on
page CAM CONFIG 1 of
the MAINTENANCE menu:
other than OFF
Remote control switch:
REMOTE (see page 11)
Setup menu item 214
REMOTE INTERFACE: SDI
33
Synchronization Reference Signals
Chapter 3 Preparations
Synchronization Reference Signals
The synchronization reference signal generator of this unit
synchronizes to a reference signal input to the REF.
VIDEO INPUT connector or to a video input signal.
External synchronization is as follows, depending on the
setting of OUT REF on the HOME page of the function
menu, and on the type of the selected input signal. Video
output signals are always synchronized to the internal
synchronization signal.
a) Same as when INT SG on page P1 INPUT of the function menu is set to
“ON”.
b) FTP connection always synchronizes to the internal synchronization
reference signal, regardless of the setting of OUT REF.
Synchronization reference signals when
you are recording, playing, or editing 720P
signals
When you are recording, playing, or editing 720P signals,
set OUT REF on the HOME page of the function menu to
“REF”, and synchronize the synchronization reference
signal generator of this unit to a reference signal input to
the REF. VIDEO INPUT connector. The following
reference signals can be used.
720/59.94P system: 1080/59.94i tri-level sync signal, 525
black burst signal
720/50P system: 1080/50i tri-level sync signal, 625 black
burst signal
When you directly interconnect video I/O connectors
between two of these units or between this unit and the
XDS-1000 or PDW-F1600/HD1500/F800/700, you can
record and dub 720P signals even if you set OUT REF on
the HOME page of the function menu to “INPUT”.
Input to SD/HDSDI
INPUT connector a)
Input to REF. VIDEO
INPUT connector Setting of OUT REF on the HOME page b)
REF INPUT
Yes Yes Synchronize to the signal input to
the REF. VIDEO INPUT connector
Synchronize to the signal input to
the SD/HDSDI INPUT connector
Yes No Synchronize to the signal input to the SD/HDSDI INPUT connector
No Yes Synchronize to the signal input to the REF. VIDEO INPUT connector
No No No external synchronization is made
34 Setting the System Frequency / Setting the Timecode
Chapter 3 Preparations
Setting the System
Frequency
This unit can record and play back video at the system
frequencies of 1080/59.94i, 50i, 29.97P, 25P, 23.98P or
720/59.94P, 50P.
Selecting the system frequency
1
Set setup menu item 013 SYSTEM FREQUENCY
SELECT MENU to “on” and press the PUSH SET
knob.
The system frequency selection screen appears.
2
Turn the PUSH SET knob to select the system
frequency to be used.
3
Press the SAVE function button (F5).
The message “Turn off/on POWER!!” appears.
4
Press the on/standby button and hold it down for one
second or longer to switch the unit to standby state,
then power it on again.
Setting the Timecode
There are the following four ways of recording timecode:
Internal Preset mode: This records the output of the
internal timecode generator, set beforehand to an
initial value. The following run modes can be
selected.
• Free Run: Timecode advances continuously.
• Rec Run: Timecode advances only during
recording.
Internal Regen (regenerate) mode: This records the
output of the internal timecode generator, initialized
to the timecode following sequentially from the
timecode of the last frame of the last clip on the disc.
External Regen (regenerate) mode: This records the
output of the internal timecode generator,
synchronized to an external timecode generator. The
timecode input to any of the following connectors can
be selected as the external input.
• TIME CODE IN connector: LTC
• SD/HDSDI INPUT connector: VITC and LTC
External Preset mode: This directly records the input of
an external timecode generator. The timecode input to
the TIME CODE IN connector can be selected as the
external input.
To record the timecode after setting an
initial value (Internal Preset)
Proceed as follows with the function menu. To set the
timecode, set TCG on page P4 TC of the function menu to
“INT” and PRST/RGN to “PRESET”.
Setting an initial timecode value
1
Press the CNTR SEL function button (F2) on the
HOME page of the function menu, and select TC.
2
Press the TCG SET function button (F3).
Time data display area
Function menu
Function buttons
35
Setting the Timecode
Chapter 3 Preparations
The first digit of the time data display starts flashing.
3
Press the T or t function button (F1 or F2) to select
a digit to be set.
The selected digit starts flashing.
4
Turn the PUSH SET knob or press the – or + function
button (F3 or F4) to set the value for the selected digit.
To set the next-most significant digit (10s digit)
Turn the PUSH SET knob while holding down the
SHIFT button.
Repeat steps 3 and 4 to set all digits that should be set.
To set to 00:00:00:00
Press the RESET/RETURN button.
5
Press the SET function button (F5).
If RUN MODE on page P4 TC is set to “FREE RUN”,
the timecode starts running.
To cancel a setting
Press the EXIT function button (F6). Any new settings to
that point are canceled, and the setting operation is
terminated.
Setting the timecode to the current time
1
Set RUN MODE on page P4 TC to “FREE RUN” and
DF/NDF to “DF” (in 59.94i/59.94P/29.97P mode
only).
2
Perform steps 1 to 4 of “Setting an initial timecode
value” (page 34) to set the timecode to a time slightly
ahead of the current time.
3
Press the SET function button (F5) at the instant when
the current time matches the displayed timecode.
Setting user bits
You can record up to eight hexadecimal digits of
information (date, time, event number, etc.) on the
timecode track.
Select UB by pressing the CNTR SEL function button (F2)
in step 1 of “Setting an initial timecode value” (page 34)
and carry out steps 2 to 5. Settings are made in
hexadecimal (0-9, A-F).
You can record ID codes in user bits.
To record the timecode that follows
sequentially from the last recorded
timecode (Internal Regen)
You can record the timecode so that it is continuous from
one clip to the next on the disc.
Set TCG on page P4 TC of the function menu to INT, and
PRST/RGN to TC or VITC. When this setting is in force,
the unit reads the timecode of the last frame of the last
recorded clip on the disc before starting to record, and
internally generates the timecode that follows the recorded
timecode.
The frame count mode (for system frequency 59.94i/
59.94P/29.97P only) is set to the same mode as the last
recorded timecode on the disc (drop-frame or non-drop-
frame).
To record with the internal timecode
generator synchronized to external
timecode (External Regen)
Use this method to synchronize the timecode generators of
a number of recorders, to record the playback timecode of
external VTRs, or to record while maintaining
synchronization between the source video and timecode.
Use either of the following procedures according to the
type of external timecode.
Synchronizing with the timecode input to the
TIME CODE IN connector
1
Connect the timecode output of an external device to
the TIME CODE IN connector, and input a reference
video signal to the REF. VIDEO INPUT connector.
2
Make the following settings on page P4 TC of the
function menu.
• Set TCG to “EXT”.
• Set PRST/RGN to “TC”.
Synchronizing with the embedded LTC input to
the SD/HDSDI INPUT connector
1
Input an SDI signal containing embedded LTC to the
SD/HDSDI INPUT connector, and a reference video
signal to the REF. VIDEO INPUT connector.
36 Superimposed Text Information
Chapter 3 Preparations
2
Make the following settings on page P4 TC of the
function menu.
• Set TCG to “SDI”.
• Set PRST/RGN to “TC”.
Executing either of these procedures starts the internal
timecode generator running in synchronization with the
external timecode generator.
Once the internal timecode generator is synchronized with
the external timecode generator, the internal timecode
generator continues to run even if the external timecode
generator connection is removed.
The timecode advance mode is set automatically to Free
Run. The frame count mode (for system frequency 59.94i/
59.94P/29.97P only) is set to the same mode as the external
timecode signal (drop-frame or non-drop-frame).
To check the synchronization to the external
signal
Press the STOP button to stop this unit, then press the REC
button.
Check that the timecode value shown in the time data
display coincides with the external timecode value.
To record an external timecode directly
(External Preset)
When you use this method, the internal timecode generator
advances without being affected by the external timecode.
To directly record the timecode input to the TIME
CODE IN connector
Input the timecode output of an external device to the
TIME CODE IN connector, and make the following
settings on page P4 TC of the function menu.
• Set TCG to “EXT”.
• Set PRST/RGN to “PRESET”.
Superimposed Text
Information
The video signal output from the COMPOSITE OUTPUT
2 (SUPER) connector, SDSDI OUTPUT 2 (SUPER)
connector, HDSDI OUTPUT 2 (SUPER) connector, and
HDMI OUT connector contains superimposed text
information, including the timecode.
Adjusting the text display
You can adjust the position, size and type of the
superimposed text using setup menu items 002, 003, 005,
009, 011, and 012.
For details, see “Items in the basic menu” (page 86).
Information displayed
The display shown above corresponds to the factory
default settings of the unit. You can change the type of
information to be displayed in the lower line of the display
by changing the setting of setup menu item 005 DISPLAY
INFORMATION SELECT.
For details, see “Items in the basic menu” (page 86).
Note
1Type of time data
2Timecode reader drop-frame mark
(for 59.94i/59.94P/29.97P mode only)
3Timecode generator drop
frame mark (for 59.94i/
59.94P/29.97P mode only)
4VITC field mark
Time data
5Operation mode
6Playback
condition mark/
Disc exchange
cache mark
37
Superimposed Text Information
Chapter 3 Preparations
aType of time data
If the time data or user bits data cannot be read correctly,
they will be displayed with an asterisk. For example,
“T*R”, “U*R”, “T*R.” or “U*R.”.
bTimecode reader drop-frame mark (for 59.94i/
59.94P/29.97P mode only)
“.”: Indicates drop-frame mode.
“:”: Indicates non-drop-frame mode.
cTimecode generator drop-frame mark (for 59.94i/
59.94P/29.97P mode only)
“.”: Indicates drop-frame mode (factory default setting).
“:”: Indicates non-drop-frame mode.
dVITC field mark
“ ” (blank): Fields 1 and 3 (for 59.94i/59.94P/29.97P/
23.98P mode) or fields 1, 3, 5 and 7 (for 50i/50P/25P
mode)
“*”: Fields 2 and 4 (for 59.94i/59.94P/29.97P/23.98P
mode) or fields 2, 4, 6 and 8 (for 50i/50P/25P mode)
eOperation mode
The field is divided into two blocks as shown below.
• Block A displays the operation mode.
• Block B displays the servo lock status or playback speed.
fPlayback condition mark/Disc exchange cache
mark
One of three channel condition marks is displayed when
the ACCESS indicator is lit during any mode except
recording. The “C” indicator appears here when the disc
exchange cache function is operating.
Display Meaning
CNT Counter data
TCR TC reader timecode
UBR TC reader user bits data
TCR. VITC reader timecode
UBR. VITC reader user bits data
TCG TC generator timecode
UBG TC generator user bits data
Note
Display Operation mode
Block A Block B
STOP Stop mode
NEXT xxxx/xxxx Cuing up the first frame of the
next clip.
PREV xxxx/xxxx Cuing up the first frame of the
current clip.
F.FWD Fast forward search
F.REV Fast reverse search
AB
PLAY Playback mode (servo unlocked)
PLAY LOCK Playback mode (servo locked)
REC Record mode (servo unlocked)
REC LOCK Record mode (servo locked)
JOG STILL A still picture in jog mode
JOG FWD Jog mode in forward direction
JOG REV Jog mode in reverse direction
SHUTTLE STILL A still picture in shuttle mode
SHUTTLE (Speed) Shuttle mode
VAR STILL A still picture in variable mode
VAR (Speed) Variable mode
TOP 0001/xxxx Cuing up the first frame of the first
clip.
END xxxx/xxxx Cuing up the last frame of the last
clip.
PREROLL Cuing up during thumbnail search
COPY Transcode copy is executing.
CLOSE A clip is not selected.
MEDIA OUT No disc is loaded.
LOADING Disc is loading.
UNLOADING Disc is unloading.
STANDBY OFF Standby state
Display Name Description
Green
condition
There is no problem with the
playback condition. This unit and
the disc can be used just as they
are. This corresponds to the
“green” channel condition
indicator of a VTR.
Yellow
condition
The playback condition has
deteriorated to some degree.
There are no read errors, but you
should take the action described
in the next section. This
corresponds to the “yellow”
channel condition indicator of a
VTR.
Red condition The playback condition has
deteriorated. There are no read
errors, a) but you should take the
action described in the next
section. This corresponds to the
“red” channel condition indicator
of a VTR.
Display Operation mode
Block A Block B
38 Superimposed Text Information
Chapter 3 Preparations
a) Read errors will occur if the playback condition continues to deteriorate.
If a read error occurs, a “Disc Error!” alarm appears in the time data
display, the picture freezes, and audio is muted.
To display playback condition marks, set setup menu item
012 CONDITION DISPLAY ON VIDEO MONITOR to
“enable”, and set setup menu item 005 DISPLAY
INFORMATION SELECT to “time data & status”.
For details about operation, see “Basic menu operations”
(page 89).
Playback condition display functions
You can be alerted in advance to deteriorating playback
conditions and to error correction rates which are
approaching their limits.
Deteriorating playback may be due to the following
causes.
• Scratches and dust on the disc surface
This includes fingerprints, dust from the air, tar from
cigarette smoke, and so on.
Scratches and soiling which occur before recording are
not a problem because they are registered in advance as
defects, and recording avoids them. However, scratches
and soiling which occur after recording can lead to
deteriorating playback conditions.
• Aging of disc recording layers
Over several decades, the recording layers of optical
discs can age and cause deteriorating playback
conditions.
You can use this function to check archival discs and
other discs which have been stored for extended periods,
so that you can take action before the deterioration
progresses further.
• Deteriorating laser diode performance
The performance of the laser diodes used in optical
heads can worsen with age, leading to deteriorating
playback conditions.
For details, see “Operating hours meter” (page 112)
about this setting.
Refer to the Service Manual for an approximate guide to
when it is time to replace optical heads.
To prevent playback conditions from
deteriorating
Pay attention to the following points when handling discs.
• Do not open disc cartridges and touch discs directly with
your hands.
• Do not store for long periods in locations which are
dusty or exposed to air circulated by fans.
• Do not store for long periods under high temperatures or
in locations exposed to direct sunlight.
If playback conditions have deteriorated
If a yellow or red playback condition mark appears, the
condition is recorded as an error log. Check the following
points.
Whether the disc displays the same playback condition
on other XDCAM devices: If so, the surface of the
disc may be dirty or scratched, or the performance of
the recording layers on the disc may have worsened
due to age. Do not use discs with these symptoms.
Whether every disc inserted into an XDCAM device
displays the same playback conditions: If so, the
performance of the laser diodes may have
deteriorated. Check the total optical output time.
For details, refer to the Service Manual.
CDisc
exchange
cache
This appears during cache
recording.
For details, see page 50.
Display Name Description
39
Basic Operations of the Function Menu
Chapter 3 Preparations
Basic Operations of the
Function Menu
The function menu provides access to frequently used
settings, such as input video signal selection and timecode
settings.
Menu settings are stored in nonvolatile memory and are
preserved even after the unit is powered off.
Function menu operations
The function menu appears on the display of this unit.
The following figure shows the buttons (F1 to F6
beginning at the top) used in function menu operations.
To display the function menu
The function menu is made up of the HOME page, P1 to
P5 pages, P6 page1), and HOME2 page1).
If the function menu is not already visible, press the
PAGE/HOME button to display it. (The most recently
accessed function menu page appears.)
1) Displayed only when maintenance menu item M38 F-KEY CONFIG is
configured.
To display a different page
Each press of the PAGE/HOME button displays the next
function menu page in the order: HOME tP1 t P2 t
P3 t P4 t P5 t P61) t HOME21) t HOME…
1) Displayed only when maintenance menu item M38 F-KEY CONFIG is
configured.
• Turning the PUSH SET knob while holding down the
PAGE/HOME button changes the page forward or
backward.
• Pressing F1 to F6 buttons while holding down the
PAGE/HOME button switches the page directly to pages
P1 to P6.
To clear the function menu from the screen
Press the DISPLAY button to switch to the video monitor
display.
To change the setting of a function menu
item
Use the function buttons.
To select the value of the setting item
Press the button to the left of each setting item to change
the value of the item. Keep pressing the button until the
value you want appears.
To set the value of the setting item
• Press the button to the left of each setting item so that the
setting value flashes to enable adjustment of the value
and then turn the PUSH SET knob to increase or
decrease the value.
• Turning the PUSH SET knob while holding down the
SHIFT button increases the increment of adjustment.
• Pressing the button to the left of each setting item while
the setting value is flashing causes the value to stop
flashing and completes the adjustment.
Function menu settings
The following tables list the setting items on each page and
describe their setting values. Underlined values are the
factory defaults.
HOME page
Function buttons (F1 to F6)
Function menu
PUSH SET knob
DISPLAY button
PAGE/HOME button
Item Setting
F1: CHAR
SEL
Turns the display of character information
on the video monitor screen and on an
external monitor on and off.
ON: Character information on
OFF: Character information off
F2: CNTR SEL Selects the type of time data to display in
the time data display area.
TC: Timecode
COUNTER: Elapsed recording or playback
time
UB: User bits
F3: TCG SET/
UBG SET
• When CNTR SEL is set to “TC” or
“COUNTER”, the “TCG SET” indicator
appears, and pressing the button displays
a screen where you can set the initial
value of timecode generated by the
internal timecode generator a) (see
page 34).
• When CNTR SEL is set to “UB”, the “UBG
SET” indicator appears, and pressing the
button displays a screen where you can
set the user bits of timecode a) (see
page 35).
40 Basic Operations of the Function Menu
Chapter 3 Preparations
a) Only when TCG on page P4 TC of the function menu is set to “INT”, and
PRST/RGN is set to “PRESET”.
P1 INPUT page a) Selectable when maintenance menu item M374 ANALOG I/O is set to
“4ch” only.
P2 INPUT page
F4: MONITR L Selects the channel to monitor as the left
monitor channel.
CH1, CH2, CH3, CH4, CH5, CH6, CH7,
CH8
CH1/2, CH3/4, CH5/6, CH7/8 (MIX)
F5: MONITR R Selects the channel to monitor as the right
monitor channel.
CH1, CH2, CH3, CH4, CH5, CH6, CH7,
CH8
CH1/2, CH3/4, CH5/6, CH7/8 (MIX)
F6: OUT REF Selects the reference signal for the output
signals of this unit.
REF: Use the signal input to the REF.
VIDEO INPUT connector as the output
reference signal.
INPUT: Use the input video signal as the
output reference signal.
Item Setting
F1: INT SG Sets whether to select test signal from
internal signal generator.
OFF: Do not select.
ON: Select.
F2: V INPUT Selects the video input signal.
HDSDI: HDSDI signal
SDSDI: SDSDI signal
Notes
• Test signal is input when INT SG on this
page is set to “ON” and setup menu item
710 is set to anything other than “Off”.
• When the system frequency is 23.98P, the
setting is fixed “HDSDI”.
F3: A1 INPUT Selects the audio input signal to assign to
audio channel 1.
SDI: Audio signal embedded in the SDI
signal
ANALOG1(MIC1): Input signal to the
ANALOG AUDIO INPUT 1 connector
AES/EBU1: Input signal to the DIGITAL
AUDIO (AES/EBU) IN 1/2 connectors
Note
Test signals are input to all audio channels
1 to 8 when INT SG on this page is set to
“ON” and setup menu item 808 is set to
anything other than “off”.
F4: A2 INPUT Selects the audio input signal to assign to
audio channel 2.
SDI: Audio signal embedded in the SDI
signal
ANALOG2(MIC2): Input signal to the
ANALOG AUDIO INPUT 2 connector
AES/EBU2: Input signal to the DIGITAL
AUDIO (AES/EBU) IN 1/2 connectors
Item Setting
F5: A3 INPUT Selects the audio input signal to assign to
audio channel 3.
SDI: Audio signal embedded in the SDI
signal
ANALOG1(MIC1): Input signal to the
ANALOG AUDIO INPUT 1 connector
ANALOG3: Input signal to the ANALOG
AUDIO INPUT 3 connector a)
AES/EBU3: Input signal to the DIGITAL
AUDIO (AES/EBU) IN 3/4 connectors
F6: A4 INPUT Selects the audio input signal to assign to
audio channel 4.
SDI:
Audio signal embedded
in the
SDI
signal
ANALOG2(MIC2): Input signal to the
ANALOG AUDIO INPUT 2 connector
ANALOG4: Input signal to the ANALOG
AUDIO INPUT 4 connector a)
AES/EBU4: Input signal to the DIGITAL
AUDIO (AES/EBU) IN 3/4 connectors
Item Setting
F1: A5 INPUT Selects the audio input signal to assign to
audio channel 5.
SDI: Audio signal embedded in the SDI
signal
ANALOG1(MIC1): Input signal to the
ANALOG AUDIO INPUT 1 connector
AES/EBU1: Input signal to the DIGITAL
AUDIO (AES/EBU) IN 1/2 connectors
F2: A6 INPUT Selects the audio input signal to assign to
audio channel 6.
SDI: Audio signal embedded in the SDI
signal
ANALOG2(MIC2): Input signal to the
ANALOG AUDIO INPUT 2 connector
AES/EBU2: Signal input to the DIGITAL
AUDIO (AES/EBU) IN 1/2 connectors
F3: A7 INPUT Selects the audio input signal to assign to
audio channel 7.
SDI: Audio signal embedded in the SDI
signal
ANALOG1(MIC1): Input signal to the
ANALOG AUDIO INPUT 1 connector
ANALOG3: Input signal to the ANALOG
AUDIO INPUT 3 connector a)
AES/EBU3: Input signal to the DIGITAL
AUDIO (AES/EBU) IN 3/4 connectors
F4: A8 INPUT Selects the audio input signal to assign to
audio channel 8.
SDI: Audio signal embedded in the SDI
signal
ANALOG2(MIC2): Input signal to the
ANALOG AUDIO INPUT 2 connector
ANALOG4: Input signal to the ANALOG
AUDIO INPUT 4 connector a)
AES/EBU4: Input signal to the DIGITAL
AUDIO (AES/EBU) IN 3/4 connectors
Item Setting
41
Basic Operations of the Function Menu
Chapter 3 Preparations
a) Selectable when maintenance menu item M374 ANALOG I/O is set to
“4ch” only.
P3 AUDIO page
a) To enable this setting, the following settings are also required, in the same
way as for volume operations for channels 1 to 4.
• Set the VARIABLE switch of the front panel to “REC” or “PB”.
• Set setup menu item 131 AUDIO VOLUME to “each”.
P4 TC page
F5: SPEAKER Sets whether or not the built-in speakers
produce output.
OFF: Not produce output.
ON: Produce output.
F6: – (Unassigned function button)
Item Setting
F1: A5 VOL Sets the volume of audio channel 5. a)
The volume can be adjusted within the
range from –200 to 0 to +200 (–∞ to
+12 dB) by turning the PUSH SET knob.
The volume changes in steps of ±10 if you
hold the SHIFT button down while you turn
the knob.
F2: A6 VOL Sets the volume of audio channel 6. a)
The volume can be adjusted within the
range from –200 to 0 to +200 (–∞ to
+12 dB) by turning the PUSH SET knob.
The volume changes in steps of ±10 if you
hold the SHIFT button down while you turn
the knob.
F3: A7 VOL Sets the volume of audio channel 7. a)
The volume can be adjusted within the
range from –200 to 0 to +200 (–∞ to
+12 dB) by turning the PUSH SET knob.
The volume changes in steps of ±10 if you
hold the SHIFT button down while you turn
the knob.
F4: A8 VOL Sets the volume of audio channel 8. a)
The volume can be adjusted within the
range from –200 to 0 to +200 (–∞ to
+12 dB) by turning the PUSH SET knob.
The volume changes in steps of ±10 if you
hold the SHIFT button down while you turn
the knob.
F5: AU METER Selects the display mode of the audio level
meters.
FULL: Display the range from –60 dB to 0
dB.
FINE: Display a magnified section with
0.25 dB step marks.
F6: LEVEL MT Specifies the position at which to
superimpose audio level meters in the
video monitor screen (in full-screen display
mode).
OFF: Do not superimpose.
LEFT: Superimpose the audio level
meters of 2 channels on the left side.
RIGHT: Superimpose the audio level
meters of 2 channels on the right side.
LEFT(4): Superimpose the audio level
meters of 4 channels on the left side.
RIGHT(4): Superimpose the audio level
meters of 4 channels on the right side.
LEFT(8): Superimpose the audio level
meters of 8 channels on the left side.
RIGHT(8): Superimpose the audio level
meters of 8 channels on the right side.
Item Setting
Item Setting
F1: TCG Selects the timecode signal to which the
internal timecode generator synchronizes.
INT: Follow the initial value set from the
front panel or remotely from the
device connected to the REMOTE
(9P) connector.
EXT: Synchronize to external timecode
signal input to the TIME CODE IN
connector.
SDI: Synchronize to timecode embedded
in the HDSDI or SDSDI signal input to
the SD/HDSDI INPUT connector.
F2: PRST/RGN Selects the following for the internal
timecode generator.
PRESET: Presets an initial value for the
timecode generated by the internal
timecode generator, as specified from
the front panel or remotely from the
device connected to the REMOTE
(9P) connector.
TC: Generate timecode synchronized to
timecode read by the internal
timecode reader.
VITC: Generate timecode synchronized to
VITC read by the internal timecode
reader.
F3: RUN
MODE
Selects the timecode run mode.
FREE RUN: Timecode advances as long
as the unit is powered on, regardless
of the unit’s operating state.
REC RUN: Timecode advances only
during recording. When you select this
item, also set F1: TCG on this page to
“INT” and set F2: PRST/RGN to
“PRESET”.
F4: DF/NDF Selects the frame count mode for the
internal timecode generator and the
counter in 59.94i/59.94P/29.97P mode.
DF: Drop-frame mode
NDF: Non-drop-frame mode
F5: PDPSET When the system frequency is set to 1080/
59.94i, 1080/29.97P, or 720/59.94P,
presets the timecode of the A frame of the
pulldown sequence.
24F TC: Reference timecode for A frame
30F TC: Timecode after pulldown
conversion from 24-frame timecode
F6: TCR Selects the type of timecode to display in
the time data display area.
TC: Display TC.
VITC: Display VITC.
AUTO: Displays VITC during playback at
±0.5× speeds or slower, otherwise
displays TC.
42 Handling Discs
Chapter 3 Preparations
P5 OTHER page
a) The target operation mode is set using setup menu item 108 AUTO EE
SELECT.
P6 OTHER page
Displayed only when a setup menu item is configured with
maintenance menu item M38 F-KEY CONFIG.
For details about configuration, refer to the Service
Manual.
HOME2 page
Displayed only when a function is configured with
maintenance menu item M38 F-KEY CONFIG.
For details about configuration, refer to the Service
Manual.
Handling Discs
Discs used for recording and
playback
This unit can record and play back the following
Professional Disc formats.
• PFD23A (capacity 23.3 GB)
• PFD50DLA (capacity 50.0 GB)
• PFD100TLA (capacity 100 GB)
• PFD128QLW (capacity 128 GB)
• It is not possible to use the following discs for recording
or playback:
- Blu-ray Disc
- Professional Disc for Data
• PFD128QLW is a quad-layer Write-Once Professional
Disc (hereinafter referred to as “quad-layer WO disc”).
Pay due attention to the following points.
- Even if you delete any files written to the disc, no
available storage space will be increased.
- Reformatting the disc will not increase the available
storage space.
- Repetitive file writing will consume the recordable
resource space (for writing the disc management data,
etc.) on the disc. If no available recordable resource
space is left on the disc, file writing may be disabled
even with sufficient available storage space remaining.
- No file can be written after the disc is finalized.
• PFD100TLA and PFD128QLW discs can be used only
by XDCAM devices with the XL-QD mark (see the
following illustration). They cannot be used by XDCAM
devices without this mark.
• Management data and other information are also
included in the capacity for each disc. For information
about the actual usable capacity, see “Recording/
playback times” (page 123) in “Specifications”.
Item Setting
F1: INDEX Sets the index picture (thumbnail) of a clip
being played back (see page 69).
F2: ERR LOG Displays the error log screen.
F3: CREATE
NEW EDL
Creates a new EDL (see page 70).
F4: ADD TO
CURT.EDL
Adds a sub clip to the current EDL (see
page 71).
F5: PB/EE Selects the video and audio signals that
are output in stop, forward direction high-
speed search, and reverse direction high-
speed search modes. a)
PB: Playback signal
EE: EE mode signal
F6: – (Unassigned function button) Notes
XL-QD mark
43
Handling Discs
Chapter 3 Preparations
Notes on handling
Handling
The Professional Disc is housed in a cartridge, and is
designed to allow handling free of risk from dust or
fingerprints. However, if the cartridge is subjected to a
severe shock, for example by dropping it, this can result in
damage or scratching of the disc. If the disc is scratched, it
may be impossible to record video/audio, or to play back
the content recorded on the disc. The discs should be
handled and stored carefully.
• Do not touch the surface of the disc itself within the
cartridge.
• Deliberately opening the shutter may cause damage.
• Do not disassemble the cartridge.
• The supplied adhesive labels are recommended for
indexing discs. Apply the label in the correct position.
Storage
• Do not store discs where they may be subjected to direct
sunlight, or in other places where the temperature or
humidity is high.
• Do not leave cartridges where dust may get inside.
• Store cartridges in their cases.
Care of the discs
• Remove dust and dirt on the outside of a cartridge using
a soft dry cloth.
• If condensation forms, allow ample time to dry before
use.
Write-protecting discs
To protect the content recorded on the disc from accidental
erasure, move the Write Inhibit tab near the bottom
(opposite side to the label surface) of the disc in the
direction of the arrow, as shown in the following figure.
You can also write protect individual clips.
For details, see “Locking (write-protecting) clips”
(page 68).
Loading and unloading a disc
When the on/standby button indicator is lit green, you can
load and unload a disc as shown in the following figure.
When the EJECT button is pressed during recording,
recording stops and the disc is ejected. If you do not want
to stop recording when the EJECT button is pressed during
recording, set setup menu item 145 MODE KEY
ENABLE DURING RECORDING to “stop”.
The DISC IN indicator flashes while the disc is being
unloaded.
Formatting a disc
Unused discs are formatted automatically when they are
loaded into this unit.
To format a recorded disc, use the Clip Menu.
For details, see “Formatting (initializing) discs”
(page 73).
Lower surface of the disc Write Inhibit tab
Slide in the direction of the arrow.
Write Inhibit tab settings
Recording enabled Recording disabled
On/standby button and indicator
To unload
Press the EJECT button.
To load
Insert disc with the label surface facing up.
The disc is drawn in.
44 Handling Memory Cards
Chapter 3 Preparations
Handling Memory Cards
About memory cards
You can use SxS memory cards with the unit by
connecting the optional SBAC-US20/US30 SxS Memory
Card USB Reader/Writer.
Memory cards that can be used with this
unit
Use the following Sony memory cards with this unit.
The memory cards that are supported differ depending on
the recording format.
SxS PRO+ series
Supports all recording formats.
SxS PRO series
Supports all recording formats.
SxS-1 series
Supported recording format: HD422/HD420 HQ/
HD420 HD 1980/DVCAM
XQD memory card series
Supported recording format: HD422/HD420 HQ/
HD420 HD 1980/DVCAM
Operation is not guaranteed if using memory cards other
than Sony SxS memory cards.
For details on using SxS memory cards and usage-related
precautions, refer to the instruction manual for the SxS
memory card.
The memory cards listed above comply with the
ExpressCard standard.
• Use the optional QDA-EX1 XQD ExpressCard Adapter
if using XQD memory cards.
• The operation of all XQD memory cards is not
guaranteed. For information about memory cards for
which operation has been confirmed, consult your Sony
dealer.
To prevent accidental erasure
You can prevent accidental recording, editing, and
deletion of data on an SxS memory card by setting the
write protect switch to the WP side.
Do not touch the write protect switch while an SxS
memory card is loaded in a memory card slot. Eject the
card before setting the write protect switch.
Notes
Note
Write protect switch
45
Handling External Storage
Chapter 3 Preparations
Handling External
Storage
You can connect a USB mass storage class device (a hard
disk drive for example) to the Super Speed USB connector
(USB 3.0 compatible) on the front panel and use it as
external storage for storing clips and other materials
(capacity: 3GB to 2TB).
You can copy material on SxS memory cards to a disc by
connecting the optional SBAC-US20/US30 SxS Memory
Card USB Reader/Writer.
The operation of all hard disk drives is not guaranteed. For
information about recommended devices, consult your
Sony dealer.
It is possible to create up to 99 folders in external storage.
Each folder can contain up to 1,200 clips (not exceeding
the total material length of 24 hours) and up to 99 EDLs.
The file system that external storage supports is exFAT
only.
Notes on use of external storage
• Only one external storage device can be recognized. Use
a direct connection, without using a hub.
• Use external storage with sector size of 512 bytes.
External storage with other sector sizes may not be
recognized by this unit.
• When using external storage, the USB drive must be
mounted in order to be recognized by this unit. If
mounting fails, a message appears prompting you to
format external storage on this unit (see page 45).
• When removing external storage, first unmount the USB
drive (see page 47).
• If external storage needs formatting, make sure to format
it on this unit. If external storage is formatted on a
different device, it may not be recognized or it is treated
as write protected on this unit.
• When the total number of files recorded on external
storage exceeds 12,000, further data writing on the same
external storage device by this unit is not possible. When
the total number of files recorded on external storage
exceeds 20,000, this unit cannot read data from that
external storage device. To use this unit with external
storage, keep in mind these limitations on number of
files.
• It is not possible to play back clips stored on external
storage directly as they are. First copy the clips you want
to play back to a disc, and then you can play back those
copied clips from the disc (see page 46).
• If you copy clips to a folder on a USB drive and then
delete or rename clips in that folder, you may not be able
to perform additional copying.
• If data is written to external storage from a device other
than this unit, writing from the unit may become
disabled.
• Deleting files on a USB drive using a computer moves
the files to the Trash folder but may not delete them.
Delete the files from the Trash folder.
Using external storage
When using external storage, mount the USB drive so that
it can be recognized by this unit, and then mount a target
folder.
To mount a USB drive
1
Connect external storage to the Super Speed USB
connector (USB 3.0 compatible) on the front panel.
2
Press the THUMBNAIL button to display the
thumbnail view.
3
Press the MEDIA SEL button.
Mounting of the USB drive starts automatically.
When the USB drive is mounted, the F1: USB DRV
indicator changes to “ON” and the USB DRIVE ON
icon ( ) appears in the status display area of the
display screen.
If there are folders in the USB drive, they are also
displayed on the display screen.
If you failed to mount the USB drive
A message appears prompting you to format external
storage.
To execute formatting, select “OK”, and then press the
PUSH SET knob. To cancel formatting, select
“CANCEL”, and then press the PUSH SET knob.
When the formatting is completed, the message “Format
was successful.” appears.
Note
46 Handling External Storage
Chapter 3 Preparations
If formatting is executed, all existing partitions (including
multipartitions) are deleted and initialized into one single
partition.
To mount a target folder
Select the folder, and press the PUSH SET knob.
The processing for folder mounting starts.
When mounting is successful, the thumbnails or a list of
stored clips in that folder are displayed.
To create a new folder
Press F3: CREATE FOLDER.
You can use F4: CREATE USB FLDR in the Clip F Menu
(see page 65) to create a copy destination folder before
executing a copy operation.
The newly created folder is automatically mounted.
To change the target folder
1
Press the FOLDER SEL button.
A list of the folders on the USB drive appears.
2
Select a folder, then press the PUSH SET knob.
Mounting of the folder starts.
When the folder is mounted, a list view or thumbnail
view of the clips stored in the folder appears.
To switch to disc thumbnail view
In thumbnail view, press the MEDIA SEL button.
The thumbnail view toggles between disc and USB drive
thumbnail view each time you press the MEDIA SEL
button.
To delete a folder in the USB drive
1
With the folders in the USB drive displayed in a list
view, select the folder you want to delete.
2
Press F6: DELETE FOLDER.
A message appears asking you whether to delete the
folder.
3
To execute deleting, select “OK” and then press the
PUSH SET knob. To cancel deleting, select
“CANCEL” and then press the PUSH SET knob.
To unmount the target folder
Press the FOLDER SEL button.
The target folder is unmounted, and the folders in the USB
drive are displayed in list view.
To use external storage to copy clips
For more information about copy operations, see
“Copying” (page 56).
To copy clips stored on external storage
1
Mount the USB drive.
2
Mount the folder containing clips you want to copy.
3
Perform the procedure described in “Copying clips”
(page 56).
To copy clips to external storage
1
Mount the USB drive.
2
Mount the copy destination folder, or create a new
folder after selecting the clip to copy (see page 46).
3
Perform the procedure described in “Copying clips”
(page 56).
Removing external storage
First unmount the USB drive, and then remove external
storage.
Note
47
Handling External Storage
Chapter 3 Preparations
The USB drive does not need to be unmounted to remove
SxS memory cards or the SBAC-US20/US30 SxS
Memory Card USB Reader/Writer.
To unmount the USB drive
1
In disc thumbnail view, press the MEDIA SEL button.
The display switches to USB drive thumbnail view.
2
Press the USB DRV OFF button.
Unmounting of the USB drive starts.
You can also press the FOLDER SEL button to display
a list of folders on the USB drive, and then press F1:
USB DRV to unmount the USB drive.
When the USB drive is unmounted, the disc thumbnail
view appears on the display screen and the USB
DRIVE ON icon ( ) in the status display area
disappears.
Note
48 Recording
Chapter 4 Recording, Playback and Copy
Chapter 4
Recording, Playback and
Copy
Recording
This section describes video and audio recording on the
unit.
See page 39 for more information about function menu
operations.
See page 89 for more information about setup menu
operations.
Preparations for recording
Make the following settings and adjustments before
starting to record.
Video input signal selection: Select with V INPUT on
page P1 INPUT of the function menu.
Audio input signal selection: Select with A1 INPUT to
A4 INPUT on page P1 INPUT, and A5 INPUT to A8
INPUT on page P2 INPUT of the function menu.
Timecode and user bits settings: See “Setting the
Timecode” (page 34).
Selection of time data to display: Select with CNTR SEL
on the HOME page of the function menu.
Selection of audio channels to monitor: Select with
MONITR R and MONITR L on the HOME page of
the function menu.
Volume adjustment of the monitor audio: Adjust with
the LEVEL knob.
Remote/local setting: Set the remote control switch. If
you set it to REMOTE, also set setup menu item 214
REMOTE INTERFACE (“RM-” and the connector
used appear on the system information of the display)
(see page 94).
SD up-convert function
You can input SD signals to the SD/HDSDI INPUT
connector and record them as HD signals.
Carrying out recording
One recording segment (from the start to the end of
recording) is called a “clip”.
1
Insert a disc.
2
Hold down the REC button, and press the PLAY
button.
Recording starts.
3
To stop recording, press the STOP button.
If the disc becomes full
Recording stops and the message “ALARM MEDIA
END.” appears on the monitor.
• Clips recorded in XAVC format and clips in other
recording formats cannot be mixed. Use another disc, or
delete the clips recorded in XAVC format.
• The shortest clip that can be recorded is 2 seconds long.
Even if recording start and stop operations are performed
within 2 seconds, a 2-second clip is recorded.
Notes
49
Recording
Chapter 4 Recording, Playback and Copy
• The maximum number of clips that can be recorded is
1,200. If the disc already contains 1,200 clips, recording
operation is not possible. (The message “MAX # Clips”
appears in the time data display area.)
• This unit can record video input signals that are not
synchronized to a reference signal. However, in that
case, video breakup and audio noise may occur during
EE playback.
• During recording, do not turn off the POWER switch on
the rear panel or disconnect the power cord. This could
cause the clip being recorded to be lost.
For details, see “Handling of discs when recording does
not end normally (salvage functions)” (page 50).
To adjust the audio recording levels
When carrying out audio recording at a reference
level
Set the VARIABLE switch to “PRESET”.
The audio signals will be recorded at a preset reference
level.
You can change the reference level and the input levels
with maintenance menu items M370 HEAD ROOM and
M373 IN LEVEL.
For details, see maintenance menu item M37 (page 105).
Manually adjusting the audio recording levels
Set the VARIABLE switch to “REC” and use the CH-1/
ALL CH and CH-2 to CH-4 knobs to adjust CH-1 to CH-4,
and use A5 VOL to A8 VOL on page P3 AUDIO of the
function menu to adjust CH-5 to CH-8 so that the audio
level indicators on the audio level meters do not exceed
0 dB for a maximum volume.
See setup menu item 108 AUTO EE SELECT (page 92) for
more information about the signal output settings in EE
mode.
To set shot marks
A Shot Mark1 essence mark or Shot Mark2 essence mark
is set if you hold down the V/MARK1 or v/MARK2
button and press the PUSH SET knob during recording.
If the unit is set up to display superimposed text
information (see page 36), “SHOTMARK*” (*: 0 to 9)
appears every time you set an essence mark.
When Shot Mark0 to Shot Mark9 is set, you can search for
the shot marks by displaying thumbnails of the frames at
those positions (see page 66).
You can also set shot marks during playback.
See page 53 for the procedure.
Recording with the HDSDI remote
control function
This section describes the settings required for recording in
HDSDI remote control mode, and how the unit operates in
this mode.
The unit (camcorder) that controls this unit must also
support HDSDI remote output.
Settings
Set setup menu item 214 REMOTE INTERFACE to
“SDI”, and set the remote control switch on the front panel
to “REMOTE”.
This unit enters HDSDI remote control mode, in which it
is controlled by command packets received via the SD/
HDSDI INPUT connector.
Commands received via the REMOTE (9P) connector are
ignored in HDSDI remote control mode.
Monitor display in HDSDI remote control mode
The “RM-SDI” network remote connection indicator (see
page 18) appears in the status display area of the display
screen. The indicator lights if command packets are
embedded in the HDSDI signals, and flashes if they are
not. However, “RM-SDI” continues to flash until the time
the controlling camcorder is powered on and the time that
the REC button is pressed on the camcorder.
Recording operation
When a recordable disc is inserted, recording (or stop) is
executed according to the REC (or STOP) command
embedded in the HDSDI signals.
Recording stops automatically when the end of the disc is
reached.
When HDSDI signals are interrupted during
recording
Recording stops if HDSDI signals are interrupted during
recording, for example because the HDSDI cable is
disconnected or the controlling camcorder is powered off.
When HDSDI signal input is restored, the unit resumes
operation according to the embedded REC or STOP
command.
Exchanging discs
Press the EJECT button, even if recording is in progress, to
eject the disc.
After a disc is exchanged, the unit resumes operation
according to the REC or STOP command embedded in the
HDSDI signal.
Note
Note
50 Recording
Chapter 4 Recording, Playback and Copy
This unit begins recording operation about one second
after the camcorder.
Continuing recording while
exchanging discs (disc exchange
cache function)
When recording is in progress, video and audio data can be
recorded to the unit’s internal memory cache during a disc
exchange (up to about 50 seconds can be cached, including
the time it takes to eject and insert the discs), and then
written back to the newly loaded disc.
1
Check that setup menu item 150 REC MODE is set to
“disc exchange cache”.
If the disc exchange cache indicator ( ) is lit in the
time data display area (see page 17) of the basic
operation display, setup menu item 150 REC MODE
is set to “disc exchange cache”.
2
If none of the indicators of step 1 appear, set setup
menu item 150 REC MODE to “disc exchange cache”.
The setting of 150 REC MODE can be changed even
during recording.
3
Exchange the disc.
During the period from the time when recording ends
on the current disc and the disc is ejected until the time
when the next disc is inserted, the unit records to its
internal cache memory. Then, after the new disc is
inserted, it copies the data from the cache to the disc
and resumes normal recording.
Disc exchange cache indicator
“C” indicator for superimposed text information
To stop disc exchange cache recording
Do any of the following during cache recording.
• Press the STOP button.
• Set setup menu item 150 REC MODE to “normal”.
• If the disc becomes full while setup menu item 150 REC
MODE is set to “disc exchange cache”, the disc is
ejected and the unit continues to record to its internal
memory (up to about 50 seconds can be cached,
including the time it takes to eject and insert the discs).
• Recording and playback operations by all buttons and
dials other than the STOP button are disabled during
cache recording.
• EJECT button operations are disabled during cache data
recording.
• If the amount of cache data exceeds the capacity of the
unit’s internal memory during a disc exchange, an alarm
message appears and the data in cache memory is
overwritten.
• The latest data continues to be recorded to internal
memory after a disc is inserted, and is appended to the
cache data recorded during the disc exchange so that
there are no breaks or interruptions in the data recorded
to the new disc.
• If you insert a disc that cannot be recorded, it is ejected
automatically. Insert a disc that can be recorded.
• If a disc with insufficient remaining recording time is
used, the unit may be unable to re-record to the disc. Use
a recently formatted disc that does not contain any clips
as the exchange disc.
• For XAVC recording, the recording of cache data takes
a certain amount of time. In this case, wait until
recording has reached the end of the recording capacity
before exchanging discs. If recording is stopped mid
disc, the disc cannot be ejected until the recording
operation finishes.
Handling of discs when recording
does not end normally (salvage
functions)
Recording processing does not end normally if, for
example, the POWER switch on the rear panel is turned off
during recording, or if the power cord is disconnected
during recording. Because the file system is not updated,
video and audio data recorded in real time is not
Note
Display Meaning
and
flash alternately
once per second
Recording to the cache
and
flash alternately
twice per second
Remaining memory capacity: Low
flashes four
times per second
Remaining memory capacity:
None (disc full)
Display Meaning
“C” flashes once
per second
Recording to the cache
“C” flashes twice
per second
Remaining memory capacity: Low
An alarm message
appears instead of
“C”.
Remaining memory capacity:
None (disc full)
Notes
Display Meaning
51
Recording
Chapter 4 Recording, Playback and Copy
recognized as files, and clip contents recorded up to that
point are lost.
However, this unit has salvage functions which can hold
losses to the minimum by reconstructing clips on such
discs. There is a quick salvage function which executes
automatically and a full salvage function which you can
execute as required.
Quick salvage: Clips are reconstructed on the basis of
backup data stored in nonvolatile memory and
markers recorded on the disc. Processing time is about
5 seconds.
Quick salvage executes automatically if the unit is
powered on with a disc still loaded after recording
was interrupted by power off.
Full salvage: Clips are reconstructed on the basis of
markers recorded on the disc. Nonvolatile memory
cannot be used, so processing takes longer than for a
quick salvage (about 30 seconds, although it depends
on the state of the disc).
You are prompted to execute a full salvage whenever
you insert a disc that was removed manually from a
powered off device after interruption of recording by
power off.
Note that no recorded clip contents are lost when the on/
standby button on the front panel is set to standby during
recording, because the unit does not enter standby mode
until after the end of recording processing.
• Even after recording finishes, do not set the POWER
switch on the rear panel to off until the ACCESS
indicator has gone out.
• These functions salvage as much recorded material as
possible after an unforeseen accident, but 100%
restoration cannot be guaranteed.
• Even when these functions are used, it is not possible to
recover data from immediately before the interruption of
recording. The amount of data lost is as follows.
Quick salvage: From 2 to 4 seconds of data before the
interruption of recording.
Full salvage: From 4 to 6 seconds of data before the
interruption of recording.
(More data may be lost when the unit is subject to
vibrations, and when you switch frequently between
recording and paused.)
• You are prompted to execute a full salvage every time
you insert a disc that has not been salvaged or power the
unit on with such a disc loaded.
• No recording is possible on discs containing clips that
have not been salvaged, although it is possible to play
back the normally recorded sections. Recording
becomes possible if you format the disc, but this erases
all of the original recorded content.
• If a “DISC Error!” alarm (see page 115) appears,
recording may not have been completed successfully
when recording on the following devices. In this case,
restore the disc using the device last used to record to the
disc.
PDW-1500, PDW-530, PDW-510, PDW-R1,
PDW-F70, PDW-F350, PDW-F330,
PDW-F75, PDW-F355, PDW-F335,
PDW-HD1500, PDW-HR1, PDW-700,
PDW-F1600, PDW-F800, PDW-HD1200, PDW-680
• If a “U1/U2 Disc!” alarm (see page 115) appears,
recording may not have completed successfully when
recording on the following devices. Restore the disc
using the device on which the disc was last used for
recording.
PDW-U1, PDW-U2
To restore clips with a full salvage
1
Insert the disc on which recording did not end
normally.
The message “Salvage OK?” appears.
To cancel the clip salvage
Press the RESET/RETURN button.
2
Press the PUSH SET knob.
Processing begins and the message “Executing.”
appears.
When processing finishes, a message appears,
displaying the results.
If the message reads “Incomplete!”, the clips that
failed were lost.
• The message “EJECT OK?” appears when “REC
INHI” is displayed. If the disc is write protected,
eject the disc, set the Write Inhibit tab to enable
recording, and then insert the disc again.
• This operation cannot be cancelled once it begins.
• When clips recorded on the following devices are
restored, a “File System” alarm (see page 115) may
appear if the data is write-protected.
PDW-HD1500, PDW-HR1, PDW-700, PDW-740,
PDW-F1600, PDW-F800, PDW-HD1200,
PDW-680
Notes
Notes
52 Playback
Chapter 4 Recording, Playback and Copy
Playback
This section describes playback of video and audio on the
unit.
Before starting playback, make the following settings and
adjustments.
Selection of time data to display: Select with CNTR SEL
on the HOME page of the function menu.
Selection of audio channels to monitor: Select with
MONITR L and MONITR R on the HOME page of
the function menu.
Volume adjustment of the monitor audio: Adjust with
the LEVEL knob.
Remote/local setting: Set the remote control switch. If
you set it to REMOTE, also set setup menu item 214
REMOTE INTERFACE (“RM-” and the connector
used appear on the display) (see page 94).
Clip playback modes
You can set the clip playback mode to either of the
following.
Continuous playback mode: The playback target is all of
the clips on the disc (factory default setting).
Single clip playback mode: The playback target is the
currently selected clip only.
To select single clip playback mode
Set setup menu item 154 SINGLE CLIP PLAY MODE to
“on”.
Playback in single clip playback mode
The available playback types include normal playback,
high-speed playback in the forward or reverse directions,
and jog, shuttle, and variable playback. Playback stops
when it reaches the start or end of the clip. The next and
preceding clips are not played, even if they exist on the
disc.
When this unit is set to repeat playback mode, the selected
clip only is played repeatedly.
To move to another clip, press the PREV, NEXT, SHIFT
+ PREV, or SHIFT + NEXT button, or perform a
thumbnail search.
Playback start position of discs
Although this unit uses discs, it is designed to offer the
most convenient features of tape playback on VTRs. The
playback start position of content on discs varies, as
described below.
After playback stop
The unit stops at the position where the STOP button was
pressed.
Press the PLAY button to resume playback at the stop
position.
After recording
The unit stops at the position where recording ended.
To play back a clip, press the PREV button to move to the
start frame of any clip or press the PREV button with the
PLAY button held down to move to any position.
Saving the playback position
The disc remembers the current playback position when it
is ejected. Inserting the disc and pressing the PLAY button
will start playback from that position.
Playback will resume from that start position even when
the disc is inserted into another XDCAM device.
• This function is not available if a disc is inserted with its
Write Inhibit tab set to disable recording.
• The playback position is not saved on PFD128QLW
Professional Discs.
SD up-convert function
The content of discs recorded in SD can be output as HD.
HD down-convert function
You can always output SD while playing discs recorded as
HD.
1080/720 cross-convert function
You can output 720 while playing clips recorded as 1080,
and output 1080 while playing clips recorded as 720.
When the system frequency of clips (59.94i/59.94P/
29.97P, 23.98P, or 50i/50P/25P) matches the system
frequency of the unit, but the number of system line
settings (1080 or 720) do not match, then clip playback is
cross-converted automatically.
Pulldown playback
When this unit’s system frequency is set to 1080/59.94i,
1080/29.97P, or 720/59.94P, clips recorded as 1080/
23.98P are converted by 2-3 pulldown before playback
(pulldown playback).
When the unit is in continuous playback mode and some
clips are selected for pulldown playback, continuous
playback of the selected clips is performed in the specified
format of pulldown playback (1080/23.98P).
Timecode in pulldown playback
During pulldown playback, timecode is also converted to
30-frame timecode to match the output video signals.
Notes
Note
53
Playback
Chapter 4 Recording, Playback and Copy
The upper row of the time data display area displays the
original 24-frame timecode, and the lower row displays the
30-frame timecode.
You can superimpose the 30-frame timecode after
pulldown on an external monitor. To do so, set setup menu
item 005 DISPLAY INFORMATION SELECT to “time
data only”.
Playback operation
This section describes the following types of playback:
Normal playback: Playback at normal speed
Playback in jog mode: Variable-speed playback, with the
speed determined by the speed of turning the jog dial
Playback in shuttle mode: Variable-speed playback, with
the speed determined by the angular position of the
shuttle dial
Playback in variable mode: Variable-speed playback,
with the speed finely determined by the angular
position of the shuttle dial
Normal playback
First insert a disc.
For details of how to insert a disc, see “Loading and
unloading a disc” (page 43).
To start playback
Press the PLAY button in continuous playback mode.
Playback starts.
When two or more clips are recorded on the disc, they are
played back in continuous playback mode.
No sound is output when non-audio signals are played
back.
To jump to the next or previous clip, then start
playback
Use the PREV button, NEXT button, jog dial, or shuttle
dial.
To stop playback
Press the STOP button.
If you play back to the end frame of the last clip, playback
automatically stops.
If, in this state, you press the PLAY button, the message
“Media End!” appears on the display.
To carry out playback again, move back to the desired clip
using the PREV button, jog dial or shuttle dial.
To set shot marks
While playing back a disc, you can set essence marks such
as Shot Mark1 and Shot Mark2 in desired frames.
To set a Shot Mark1 or Shot Mark2, hold down the
V/MARK1 or v/MARK2 button and press the PUSH SET
knob.
You can delete essence marks on the chapter thumbnail
screen (see page 67).
Shot marks cannot be set to a locked clip.
Playback in jog mode
In jog mode, you can control the speed of playback by the
speed of turning the jog dial. The playback speed range is
–1 to +1 times normal speed.
To carry out playback in jog mode, proceed as follows.
1PREV button
2PLAY button
3NEXT button
4STOP button
5Jog dial
6Shuttle dial
7V/MARK1 button and v/MARK2 button
Note
Note
Jog/shuttle transport
indicators
54 Playback
Chapter 4 Recording, Playback and Copy
1
Press the SHTL/JOG button or VAR/JOG button,
turning it on.
When the SHTL/JOG or VAR/JOG button is pressed
during recording, recording stops and the unit enters
jog mode. If you do not want to stop recording, set
setup menu item 145 MODE KEY ENABLE
DURING RECORDING to “stop”.
2
Turn the jog dial in the desired direction, at the speed
corresponding to the desired playback speed.
Playback in jog mode starts.
The Jog/shuttle transport indicators light as follows.
b (green): Lights during playback in the reverse
direction.
B (green): Lights during playback in the forward
direction.
3
To stop playback in jog mode, stop turning the jog dial.
When setup menu item 101 SELECTION FOR
SEARCH DIAL ENABLE is set to “dial direct”
(factory default setting), you can start jog playback by
simply rotating the jog dial, even when the SHTL/JOG
and VAR/JOG buttons are not lit.
Playback in shuttle mode
In shuttle mode, you can control the speed of playback by
the angular position of the shuttle dial. The range of
playback speed is ±20 times normal speed or maximum
speed.
To carry out playback in shuttle mode, proceed as follows.
1
Press the SHTL/JOG button, turning it on.
When the SHTL/JOG button is pressed during
recording, recording stops and the unit enters shuttle
mode. If you do not want to stop recording, set setup
menu item 145 MODE KEY ENABLE DURING
RECORDING to “stop”.
2
Turn the shuttle dial to the desired angle
corresponding to the desired playback speed.
Playback in shuttle mode starts.
The shuttle dial has a detent at the center position, for
still image playback.
The Jog/shuttle transport indicators light as follows.
b (green): Lights during playback in the reverse
direction.
B (green): Lights during playback in the forward
direction.
x (red): Lights during still image display.
3
To stop playback in shuttle mode, return the shuttle
dial to the center position, or press the STOP button.
When setup menu item 101 SELECTION FOR
SEARCH DIAL ENABLE is set to “dial direct”
(factory default setting), you can start shuttle playback
by simply rotating the shuttle dial, even when the
SHTL/JOG button is not lit.
• When setup menu item 101 SELECTION FOR
SEARCH DIAL ENABLE is set to “dial direct”, after
using the shuttle dial, return it to the center position. If
the shuttle dial is not in the center position, it is possible
occasionally for vibration from other operations to
activate the dial, and start playback in shuttle mode.
• If you switch to shuttle mode and operate the shuttle dial
during playback, the initial shuttle playback speed will
skip one step.
For example, if the shuttle dial is in the center position
during playback, the shuttle playback will start at 1.0
times normal speed, not at 0.5 times normal speed.
To alternate between normal-speed playback and
shuttle mode playback
Set the shuttle dial to the position corresponding to the
desired shuttle playback speed, then press the PLAY and
SHTL/JOG buttons alternately.
Playback in variable mode
In variable mode, you can control the speed of playback in
the range of –2 to +2 times normal speed by the angular
position of the shuttle dial.
For playback of XAVC-format clips in variable mode, you
can control the speed of playback in the range –1 to +2
times normal speed.
To carry out playback in variable mode, proceed as
follows.
Jog/shuttle
transport indicators
Notes
55
Playback
Chapter 4 Recording, Playback and Copy
1
Press the VAR/JOG button, turning it on.
When the VAR/JOG button is pressed during
recording, recording stops and the unit enters variable
mode. If you do not want to stop recording, set setup
menu item 145 MODE KEY ENABLE DURING
RECORDING to “stop”.
2
Turn the shuttle dial to the desired angle
corresponding to the desired playback speed.
Playback in variable mode starts.
The shuttle dial has a detent at the center position, for
still image playback.
The Jog/shuttle transport indicators light as follows.
b (green): Lights during playback in the reverse
direction.
B (green): Lights during playback in the forward
direction.
x (red): Lights during still image display.
3
To stop playback in variable mode, return the shuttle
dial to the center position, or press the STOP button.
If you switch to variable mode and operate the shuttle dial
during playback, the initial variable playback speed will
skip one step.
For example, if the shuttle dial is in the center position
during playback, the variable playback will start at 0.12
times normal speed, not at 0.06 times normal speed.
To alternate between normal-speed playback and
variable mode playback
Set the shuttle dial to the position corresponding to the
desired variable playback speed, then press the PLAY and
VAR/JOG buttons alternately.
To repeat playback in variable mode
Set setup menu item 142 REPEAT MODE to “play &
VAR fwd” or “force”.
This allows you to perform repeat playback, limited to
variable playback in the forward direction in the range 0 to
+1 times normal speed.
Playback operations using
thumbnails
Playback operations that you can perform with thumbnails
include searching for clips, displaying clip information,
playing clip lists created, and locking and deleting clips.
This allows you to check the actual video as you work.
See “Clip Operations” (page 66) for more information
about thumbnail.
Note
Jog/shuttle transport
indicators
56 Copying
Chapter 4 Recording, Playback and Copy
Copying
Overview
This unit can copy clips, EDLs, and other files stored on
discs to external storage. It can also copy clips, EDLs, and
other files from external storage to discs.
Copying clips and EDLs on discs to external storage
enables repeated use of the disc for recording.
The unit can also copy clips, EDLs, and other files stored
on SxS memory cards to discs.
To copy SxS memory cards, the SBAC-US20/US30 SxS
Memory Card USB Reader/Writer is required.
Limitations
• When you copy a clip with a duration that exceeds six
hours, the clip is divided into separate clips at each six-
hour point.
• Index picture settings may be displaced forward or
backward when you execute a copy.
• When an MXF clip is copied, the UMID data of the copy
source clip is maintained intact. If the copy destination
media contains a clip with the same UMID data as the
clip selected as the copy source, it is not possible to copy
the selected clip. Change the UMID data on the external
device, or transfer the copy source clip via the network.
• Seamless playback and clip flag operations (addition,
modification, and deletion) are not supported for MXF
clips that meet the following conditions.
- Clips containing 1,000 or more essence marks
- Clips containing 10,804 or more timecode breaks
- Clips with metadata files *M01.XML more than 2 MB
in size
• Do not play back a clip while copying the clip. The
output may become distorted or muted.
Copy operations
Copying clips
To copy from a disc to external storage
To copy from external storage to a disc
1
Insert a disc into the disc slot.
2
Select the media containing target clips, and press the
THUMBNAIL button.
The clip list screen appears.
To change the folder for displaying thumbnails
Press the FOLDER function button (F3) and select the
folder to display thumbnails.
Example: To display thumbnails of MPEG-4 AVC/
H.264-format recorded clips, press the FOLDER
function button (F3) and select XDROOT.
3
Do one of the following to select the clip to copy.
• Turn the PUSH SET knob.
• Press the arrow buttons.
To select several consecutive clips
Move the cursor to the start or end of the clips that you
want to select, and then proceed as described above
while holding down the SHIFT button.
When copying all clips on a disc
Proceed to step 4 without carrying out clip selection
operation.
To copy part of a clip
When you select a single clip and press the arrow
buttons to set an IN and OUT point in the clip, it
becomes possible to copy the section defined by the IN
and OUT points.
For details about how to set an IN and OUT point, see
“To copy the specified part of a clip” (page 57).
4
Press the COPY button.
The Clip Copy screen appears.
To change the copy source clip
Press the RETURN button to return to the clip list
screen, and then select another clip.
To cancel the copy operation
Press the CANCEL function button (F6) or the RESET
button.
5
Press the SOURCE function button (F1) to filter the
copy source clips.
To copy the clips selected in step 3: Select
“SELECTED”.
To copy all the clips on the disc: Select “ALL”.
57
Copying
Chapter 4 Recording, Playback and Copy
6
Press the START function button (F5).
Copying of the clips starts.
The progress of the copying is shown on the Clip Copy
screen, and the copy icon lights in the status display
area.
To abort the copy operation
Press the ABORT function button (F1), and then press
the YES (F5) function button.
The data already transferred to the destination media
remains on that media.
If the copy operation is completed successfully, the
message “Copy was successful.” appears.
7
Press the OK function button (F5).
The Clip Copy screen disappears, and you return to the
original screen.
To copy an EDL file
An EDL can be copied by an operation similar to a clip
copy operation. However, it is necessary to make a copy of
all clips referenced by the EDL in advance. Therefore,
“ALL” is automatically selected in step 3 of the procedure
for “Copying clips” (page 56).
To copy the specified part of a clip
When you set an IN and OUT point in the clip, it becomes
possible to copy only the part defined by the IN and OUT
points.
1
On the video monitor screen, cue the clip up to the
frame where you want set an IN point.
2
Press the PUSH SET knob while holding down the
B/IN button.
An IN/OUT setting window appears in the bottom
right corner of the display.
The IN point timecode is displayed in the IN/OUT
setting window, and the IN indicator lights.
3
Cue up to the frame where you want to set an OUT
point.
4
Press the PUSH SET knob while holding down the
b/OUT button.
An IN/OUT setting window appears in the bottom
right corner of the display.
The OUT point timecode and the duration (DUR) are
displayed in the IN/OUT setting window, and the OUT
indicator lights.
5
Carry out step 4 and follow the procedure in “Copying
clips” (page 56).
To check the clip with IN and OUT points set
1
Press the B/IN or b/OUT button.
An IN/OUT setting window appears in the lower right
of the display.
2
Press the NEXT or PREV button.
The unit cues up the frame with the IN (or OUT) point
set.
To delete the IN/OUT points
1
Press the B/IN button (or b/OUT button).
The IN/OUT setting window appears in the bottom
right corner of the display.
2
Press the RESET button.
The IN (or OUT) indicator turns off.
The following operations delete the IN/OUT points
automatically.
• Change the selection of media.
• Remove the media.
Note
IN indicator
OUT indicator
58 Copying
Chapter 4 Recording, Playback and Copy
• Delete the clip in which IN/OUT points are set.
• Format the media.
59
Overview
Chapter
Chapter 5 Operations on Clip List Screens
5
Operations on Clip List
Screens
Overview
Use clip list screens to search for scenes, play scenes found
by searching, select clips to copy, and perform other
operations related to clips.
You can switch between the details view and the
thumbnails view of clip list screens.
Switching between display screens
To switch between the basic operation screen, video
monitor screen, and clip list screens (thumbnails view and
details view), press the THUMBNAIL button (1) or
DISPLAY button (2).
The screens change as shown in the following figure.
Clip list screen (thumbnails view)Basic operation screen
Video monitor screen Clip list screen (details view)
a) Switches back to the screen that was displayed before the last transition.
b) Also switches to the Rec Start essence mark thumbnail screen when setup menu item 153 FIND MODE is set to “clip & rec start mark”
(see page 93).
60 Overview
Chapter 5 Operations on Clip List Screens
Information and controls on clip list
screens
Thumbnails view
aClip storage location
Displays the storage location of the currently displayed
clips and EDLs in the format “recording media/folder”.
bThumbnail
Thumbnail of a clip or an EDL icon.
Thumbnails of clips and EDL icons can be displayed on
the same clip list screen, with clip thumbnails displayed
first.
For details, see “Thumbnail display items” (page 61).
cClip number/total number of clips
Displays the total number of clips (including EDLs) on the
selected media, and the number of the selected clip (or
EDL).
dScrollbar
When not all of the thumbnails can be displayed in the
thumbnail display area, the position of the slider shows the
relative position of the currently displayed clips, and the
length of the slider shows the relative length of currently
displayed clips within all of the clips.
eClip name
Displays the name of the selected clip (or EDL).
When multiple clips are selected, displays the name of the
first clip or the most recently selected clip.
Clip names can be displayed in European languages
(English, French, German, Italian, etc.), Japanese, Hangul
characters, and Chinese (both simplified and traditional
characters).
• Every character that cannot be displayed properly is
represented by a x.
• Clip names that are too long are displayed truncated. To
view the entire character string of the name, access the
Clip Properties screen (see page 61).
fVideo format
The video format of the selected clip is displayed as a
combination of the following items.
• Video format logo
• Number of system lines and recording quality
• System frequency
gAudio format
The audio format of the selected clip is displayed as a
combination of the following items.
• Number of audio channels
• Quantization bit rate
hDuration
Displays the duration (recording time) of the selected clip.
When multiple clips are selected, displays the total
recording time of the selected clips.
iClip date and time
Displays the date and time when the selected clip was shot
and recorded.
jSelection frame
Indicates that the clip is selected. To select another clip,
move the frame (see page 66). Multiple selection frames
appear when multiple clips are selected (see page 66).
Details view
For details about the following items, see “Thumbnails
view” (page 60).
Notes
61
Overview
Chapter 5 Operations on Clip List Screens
1Clip storage location
3Clip number/total number of clips
6Duration
7Clip date and time
8Video format
9Audio format
qa Selection frame
bDetails display area
Displays a details list of clips and EDLs on the selected
media.
The list is made up of the following columns.
• No. (line number)
• NAME (clip name)
• DATE (clip date and time)
• DURATION (recording time)
dThumbnail
Displays the thumbnail of the selected clip (or the EDL
icon when an EDL is selected).
For details, see “Thumbnail display items” (page 61).
eTimecode
Displays the starting timecode of the selected clip.
jScrollbar
When not all of the clips can be displayed in the details
display area, the position of the slider shows the relative
position of the currently displayed clips, and the length of
the slider shows the relative length of currently displayed
clips within all of the clips.
kEDL mark
The mark appears when the item is an EDL.
Clip Properties screen
When you select a clip and press the CLIP PROPERTY
function button (F2), this screen displays the properties of
the selected clip.
Name: Clip name
Title1: Title1
Title2: Title2
AV Format: Recording format
Frame Rate: The frame rate at the time when the clip was
shot. For clips shot using Slow & Quick Motion, the
PB (playback)/Capture (shooting) frame rates are
shown.
TC/DUR: Timecode of the first frame/Recording time
Created: Date and time of creation
Modified: Date and time of most recent modification
Rec Device: Name of device that created the clip (product
number)
The Clip Properties screen displays the entire character
string of long clip names and titles.
To scroll hidden parts of the string into view
When a b or B mark is displayed for an item, you can
press the left arrow or right arrow button to scroll the
display by one character for each press.
The up arrow and down arrow buttons scroll the beginning
and end of the string into view.
When there is any hidden part of the string, arrows are
displayed on the left and right of the “Scroll” indicator at
the bottom left of the screen.
To change the selected clip
Use the NEXT or PREV button (or use them with the
SHIFT button) (see page 66).
Thumbnail display items
Only 6 and 9 are displayed on EDL icons.
aIndex picture
Displays an image representing the content of the clip.
Normally the index picture is the first frame in a clip, but
you can change it to any frame in the clip for a different
index picture.
For the method of changing the index picture frame, see
“Setting the index picture frame” (page 69).
bIndex picture changed mark
This mark, like the folded-over corner of a page that you
want to remember, appears when the index picture has
been changed to any frame other than the first frame of a
clip.
Note
62 Overview
Chapter 5 Operations on Clip List Screens
When you cue up a clip, the unit always cues up the first
frame, even when the index picture has been changed to a
different frame.
cClip flag icon
Displays the corresponding icon when a clip flag (OK/NG/
KP(KEEP)) is set in the clip (see page 67).
dS mark
This mark appears when shot marks or other essence
marks have been set in the clip.
eLock icon
This icon appears when the clip is locked (protected) (see
page 68). Clips cannot be deleted and their clip
information cannot be changed when this mark is
displayed.
fUnplayable icon
An unplayable icon ( ) indicates that the clip (or EDL)
cannot be played, for example because the system
frequency settings differ from the current settings of this
unit.
gClip information
Displays the clip information selected with the CLP INFO
item in the Clip F Menu (see page 65). The factory default
selection is the timecode of the first frame.
h“No proxy AV data” icon
This icon appears when the clip does not include proxy AV
data.
i“Cannot copy” icon
You cannot copy clips (or EDL) marked with this icon.
Expanded thumbnail screen
This screen displays thumbnails of equally sized divisions
of the selected clip or EDL.
For details about how to display the expanded thumbnail
screen, see “To search through a clip on the expanded
thumbnail screen” (page 66).
aSelection frame
Indicates that the thumbnail is selected. To select another
thumbnail, move the frame (see page 66).
bClip name
Displays the name of the clip displayed in the expanded
thumbnail screen.
cClip number/total number of clips
Displays the total number of clips on the selected media
and the number of the clip whose expanded thumbnails are
currently displayed.
dThumbnail number/total number of thumbnails
Displays the total number of thumbnails of the divided clip
and the number of the currently selected thumbnail.
eNumber of divisions
Displays the number of times that the selected clip has
been divided to display the expanded thumbnails.
fDuration
Displays the time from the selected thumbnail to the next
thumbnail.
gScrollbar
See the description of “Scrollbar” under “Thumbnails
view” (page 60).
Chapter thumbnail screen
Chapters are the sections between the shot marks, Rec
Start marks, and other essence marks that have been
recorded in clips or EDL sub clips. This screen allows you
to display thumbnails of the chapters in the selected clip or
EDL.
For details about how to display the chapter thumbnail
screen, see “To search through a clip on the chapter
thumbnail screen” (page 66).
Note
63
Overview
Chapter 5 Operations on Clip List Screens
Rec Start essence marks are set automatically at the start of
recording, but shot marks can be set at any scene during
recording or playback.
See page 49 and page 53 for more information about shot
mark setting.
aSelection frame
Indicates that the thumbnail is selected. To select another
thumbnail, move the frame (see page 66). Multiple
selection frames appear when multiple thumbnails are
selected (see page 66).
bClip name
Displays the name of the clip displayed on the current
chapter thumbnail screen.
cClip number/total number of clips
Displays the total number of clips on the selected media
and the number of the clip whose chapter thumbnails are
currently displayed.
dChapter number/total chapters
Displays the total number of chapters and the number of
the selected chapter.
eEssence mark indicator
Displays the type of the essence marks which are set on the
selected chapter.
fS0 to S9/RS/S marks
“S0” to “S9” and “RS” marks on the thumbnails indicate
frames where Shot Mark0 to Shot Mark9 and Rec Start
essence marks are set. “S” marks indicate frames where
essence marks other than shot marks and Rec Start essence
marks are set.
No such marks are displayed on thumbnails of EDL sub
clips.
gDuration
Displays the time from the first frame of the selected
chapter to the first frame of the next chapter.
hScrollbar
See the description of “Scrollbar” under “Thumbnails
view” (page 60).
Rec Start essence mark thumbnail screen
This screen displays the first frames or the frames on
which Rec Start essence marks are set for all the clips
stored on the disc.
aSelection frame
Indicates that the thumbnail is selected. To select another
thumbnail, move the frame (see page 66).
Multiple clips cannot be selected.
bClip storage location
Displayed as “Disc/Clip” in the Rec Start essence mark
thumbnail screen.
cEssence mark name
Displays “Rec Start”, indicating a Rec Start essence mark.
dClip number/total number of clips
Displays the total number of clips on the media and the
number of the clip that is currently selected.
eEssence mark number/total number of essence
marks
Displays the total number of Rec Start essence marks on
the media and the number of the Rec Start essence mark
that is currently selected.
fRS mark
Indicates that a Rec Start essence mark has been set.
64 Overview
Chapter 5 Operations on Clip List Screens
gClip date and time
Displays the date and time when the clip that contains the
selected frame was shot and recorded.
hClip name
Displays the name of the clip that contains the selected
frame.
iClip information
Displays the clip information selected with the CLP INFO
item in the Clip F Menu (see page 65). Under factory
default settings, the timecode of the frame on which the
Rec Start essence mark is set is displayed.
jScrollbar
See the description of “Scrollbar” under “Thumbnails
view” (page 60).
Clip Menu
The Clip Menu provides the following commands for
operations on clips.
The shortcut buttons shown in parentheses ( ) allow you to
open menu items directly. For example, “SHIFT + STOP”
means to press the STOP button while holding down the
SHIFT button.
To display the Clip Menu
Press the MENU button with a clip list screen (thumbnails
view or details view) displayed.
To return to the original screen, press the MENU button
again.
Clip Menu operations
To move the focus bar up or down: Press the V/MARK1
or v/MARK2 button, or turn the PUSH SET knob.
To move from a menu level to the next lower menu
level: Press the b/OUT button or PUSH SET knob.
To move from a menu level to the next higher menu
level: Press the B/IN button or RETURN button.
To execute a command: Press the PUSH SET knob.
Clip F Menu
The clip list screens and expanded/chapter thumbnail
screens provide the Clip F Menu, which can be accessed
directly with function buttons.
Following is a list of Clip F Menu commands. Underlined
settings are the factory defaults.
Item Sub-item Function
Delete Clips
(SHIFT + RESET)
Delete
Selected Clips
Deletes the selected
clips.
Delete ALL
Clips
Deletes all clips on the
selected media.
Lock Unlock Clips
(SHIFT + STOP)
Lock Selected
Clips
Locks the selected
clips.
Lock All Clips Locks all clips on the
selected media.
Unlock
Selected Clips
Unlocks the selected
clips.
Unlock All
Clips
Unlocks all clips on the
selected media.
Set Clip Flag OK Sets the OK flags in the
selected clips.
NG Sets the NG flags in the
selected clips.
KP(KEEP) Sets the KEEP flags in
the selected clips.
(none) Clears clip flags that
have been set in the
selected clips.
Remove Essence
Marks
Remove
Selected Clip’s
EM
Removes the essence
marks from the
selected clip.
Remove All
Clip’s EM
Removes the essence
marks from all the clips
on the selected media.
Format Media – Formats (initializes) a
disc
Note
Finalized discs cannot
be formatted.
Finalize Disc – Finalizes a write-once
type Professional Disc.
Notes
• You cannot write
additional data to
finalized discs.
• Finalized discs
cannot be finalized
again.
Update/Restoring
Media
– Rebuilds the disc
management data.
Media Properties – Displays the disc
information.
Settings Select Clip
Language
Selects the clip name
display language.
• Alphabet
•Korean
• Simplified Chinese
• Traditional Chinese
• Japanese
Select Alarm
Language
Selects the alarm
display language.
• English
• Japanese
Item Sub-item Function
65
Overview
Chapter 5 Operations on Clip List Screens
CLIP page
On clip list screens
a) Does not appear when the clip list screen is in details view.
b) Does not switch when the Rec Start essence mark thumbnail screen is
displayed.
On expanded/chapter thumbnail screens
c) Not displayed when the expand thumbnail screen is displayed.
P1 EDL page
Parentheses ( ) indicate shortcut buttons for directly
accessing a menu item.
Shortcut buttons for EDL edit commands
If a clip that you want to make a sub clip is selected on a
clip list display screen, you can invoke the F3: CREATE
NEW EDL command by pressing and holding the SHIFT
button and pressing the PUSH SET knob.
For the procedure for creating EDLs, see “Creating and
editing EDLs” (page 70).
To display the Clip F Menu
Press the PAGE/HOME button or function buttons (F1 to
F6) with a clip list screen (thumbnails view or details view)
or expanded/chapter thumbnail screen displayed.
When the Rec Start essence mark thumbnail screen is
displayed, the CLIP page of the Clip F Menu will be
displayed when you press the PAGE/HOME button or
function button (F1).
In the Rec Start essence mark thumbnail screen, only F1:
CLP INFO is displayed.
To display a different page
Each press of the PAGE/HOME button displays the next
function menu page in the order: CLIP t P1 t CLIP…
Item Function
F1: CLP INFO a) Selects the information to be displayed at
the bottom of the thumbnails.
DATE:
Date and time of creation, or date and
time of the most recent modification
TC: Timecode of first frame
DURATION: Playback time
SQ NO.: Sequence number of thumbnail
F2: CLIP
PROPERTY b) Displays the Clip Properties screen
(see page 61).
F3: FOLDER b)
Selects the folder on the disc whose content
you want to display on the clip list screen.
F4: CREATE
USB FLDR b)
When external storage is connected to this
unit and the USB drive is mounted, creates
a copy destination folder in the USB drive to
enable a clip on a disc to be copied to
external storage. (The name of the copy
destination folder will automatically be the
shooting date of the clip.)
Note
This operation cannot be executed if the
USB drive is write inhibited. Unlock the
drive and try again.
For the operation to write enable the USB
drive, refer to the instruction manual for the
external storage device that you are using.
F5: CHAPTER b) Displays the chapter thumbnail screen
(see page 62).
F6: EXPAND b) Displays the expanded thumbnail screen
(see page 62).
Item Function
F1: CLP INFO Selects clip information to be displayed at
the bottom of the thumbnails.
DATE:
Date and time of creation, or date and
time of the more recent modification
TC: Timecode of first frame
DURATION: Playback time
SQ NO.: Sequence number of thumbnail
F2: SUB CLIP
INFO c) Displays EDL sub clip information.
Selectable when the chapter thumbnail
screen (sub clips) is displayed.
F3: GOTO SUB
CLIP c) Switches to the clip list screen and
displays the selected sub clip.
Selectable when the chapter thumbnail
screen (sub clips) is displayed.
F4: REMOVE c) Deletes the selected essence mark or
EDL sub clip (see page 67).
F5: CHAPTER Displays the chapter thumbnail screen
(see page 62).
F6: EXPAND Displays the expanded thumbnail screen
(see page 62).
Item Function
F1: SET CURT.EDL Sets the current EDL.
F2: RELEASE CURT.EDL Releases the current EDL.
F3: CREATE NEW EDL
(SHIFT + PUSH SET
knob)
Creates a new EDL.
F4: ADD TO CURT.EDL Adds sub clips to the current
EDL.
F6: GOTO CURT.EDL Refers to the current EDL.
Note
Item Function
66 Clip Operations
Chapter 5 Operations on Clip List Screens
Clip Operations
Selecting clips
Select clips with the selection frame (see page 60).
To move the selection frame
Do one of the following.
• Turn the PUSH SET knob.
• Press the arrow buttons.
• Press the NEXT or PREV button.
• Turn the shuttle/jog dial. (The selection frame moves at
high speed in shuttle mode and at low speed in jog
mode.)
To jump to the first clip
Press the PREV button while holding down the SHIFT
button.
To jump to the last clip
Press the NEXT button while holding down the SHIFT
button.
To make a consecutive selection of clips
Move the selection frame to the first clip that you want to
select. Then, while holding down the SHIFT button, turn
the PUSH SET knob.
To cancel the consecutive selection, move the selection
frame without the SHIFT button held down.
Searching with thumbnails
You can put the clip list screen into thumbnails view (see
page 60) to search for desired clips while viewing
thumbnails.
To search for clips while viewing clip names, press the
DISPLAY button to switch to details view (see page 60).
To search through a clip on the expanded
thumbnail screen
The expand function allows you to divide a clip selected on
the clip list screen into equally sized blocks, and to display
a list of thumbnails of those blocks. This is a quick and
efficient way to review the selected clip and search for
target scenes. You can specify 12, 144, or 1728 divisions.
1
On the clip list screen, select the thumbnail of the clip
that contains the scene you want to find.
2
Press the PAGE/HOME button to display the function
menu, and press the EXPAND function button (F6).
The selected clip is divided into 12 blocks, and a list
appears on the expanded thumbnail screen (see
page 62) with the first frame of each block displayed
as a thumbnail.
3
Select the thumbnail that you want to expand further.
4
Repeat steps 2 and 3 up to 2 times, as required.
If the duration of each block after division would be
shorter than one frame, division is performed so that an
expanded thumbnail screen is displayed in which the
duration of each block is one frame. In this case, no such
expanded thumbnail screen is displayed that represents
further expansion.
For example, a 100-frame clip is divided into 100 blocks
when you press the EXPAND function button (F6) twice
and an expanded thumbnail screen is displayed in which
the duration of each block is one frame. A third press of the
EXPAND function button (F6) displays no expanded
thumbnail screen representing further expansion.
To return to the previous expansion level
Press the EXPAND function button (F6) while holding
down the SHIFT button.
To display the expanded thumbnail screen of the
previous or next clip
With the expanded thumbnail screen still active, press the
PREV button or the NEXT button.
An expanded thumbnail screen appears displaying the
thumbnails of 12 equal blocks resulting from division of
the previous or next clip.
To search through a clip on the chapter
thumbnail screen
The chapter function allows you to display thumbnails of
the chapters in a clip.
See page 60 for more information about thumbnail view.
See page 62 for more information about the chapter
thumbnail screen.
1
On the clip thumbnail screen, select the thumbnail of a
clip or the icon of an EDL with chapters set.
The S mark (see page 62) appears on the thumbnails of
clips with chapters set. (No S marks are displayed on
EDL icons.)
Note
67
Clip Operations
Chapter 5 Operations on Clip List Screens
2
Press the PAGE/HOME button to display the function
menu, and press the CHAPTER function button (F5).
The chapter thumbnail screen (see page 62) appears,
with thumbnails of the frames where chapters are set.
The “S0” to “S9” and “RS” marks on the thumbnails
indicate frames where Shot Mark0 to Shot Mark9 and
Rec Start essence marks are set. The “S” marks on the
thumbnails indicate frames where essence marks other
than shot marks and Rec Start essence marks are set.
No such marks are displayed on thumbnails of EDL
sub clips.
To delete the shot mark at a chapter position
You can delete the shot mark (Shot Mark0 to Shot Mark9)
at the chapter position on the chapter thumbnail screen.
(Rec Start essence marks and EDL sub clips cannot be
deleted.)
1
On the chapter thumbnail screen, select the thumbnail
for the frame whose shot mark you want to delete.
2
Press the PAGE/HOME button to display the function
menu, and press the REMOVE function button (F4).
A message appears asking if you are sure that you want
to delete the shot mark.
3
Select “OK” to delete the mark, or “Cancel” to cancel
the deletion, and then press the PUSH SET knob.
To display the chapter thumbnail screen of the
previous or next clip
With the chapter thumbnail screen still active, press the
PREV button or the NEXT button.
To display the Rec Start essence mark
thumbnail screen
Set setup menu item 153 FIND MODE to “clip & rec start
mark” beforehand.
You can switch between screens in the following sequence
by pressing the DISPLAY button in a clip list screen: clip
list screen (details view) t clip list screen (thumbnails
view) t Rec Start essence mark thumbnail screen. You
can switch between the a clip list screens and Rec Start
essence mark thumbnail screen with the DISPLAY button
as long as the setup menu item 153 setting is not changed.
This setting can be used as a shortcut when viewing the
start points of clips recorded using the continuous clip
recording function of an XDCAM camcorder, for
example.
In addition, pressing the THUMBNAIL button when the
Rec Start essence mark thumbnail screen is displayed
toggles between it and the video monitor screen. Pressing
the PREV and NEXT buttons in the video monitor screen
cues up to the frames on which Rec Start points are set.
• You cannot switch to the Rec Start essence mark
thumbnail screen by pressing the DISPLAY button in
the expanded thumbnail screen or chapter thumbnail
screen.
• The continuous clip recording function is not available
on this unit. To record in continuous clip recording
mode, use an XDCAM camcorder or other device that
supports the continuous clip recording function to create
a disc.
Playing a clip by thumbnail search
After finding a clip with one of the methods explained in
the previous section, “Searching with thumbnails”
(page 66), you can cue up or play the clip that you have
found.
To cue up the clip
Select the clip you have found, and then press the PUSH
SET knob.
To play the clip
Select the clip you have found, and then press the PLAY
button.
Setting clip flags
You can set three types of clip flags (OK/NG/KP(KEEP))
for selected clips. Setting these flags in each clip that you
record makes it easy for editors and other colleagues to
find and select the clips that they need.
1
On a clip list screen, select the clip where you want to
set a flag (multiple selections possible).
2
Display the Clip Menu.
3
Select Set Clip Flag.
The Set Clip Flag screen appears.
On this screen, a x mark appears in front of the name
of each flag that is set in one or more of the currently
selected clips.
4
Select the clip flag that you want to set (OK/NG/
KP(KEEP)), and then press the PUSH SET knob.
Notes
68 Clip Operations
Chapter 5 Operations on Clip List Screens
The clip flag is set for all selected clips, and the clip
flag icon (see page 62) appears on thumbnails.
To clear clip flags
Carry out steps 1 to 3, selecting a clip that has a flag set,
and then select “(none)” in step 4.
Locking (write-protecting) clips
On a clip list screen, you can lock the selected clips so that
they cannot be deleted or altered.
Locking prevents the following operations on clips.
• Deletion
• Changing the index picture
• Adding and deleting shot marks
• Setting and clearing clip flags
• Locked clips are deleted along with other clips when
media is formatted.
• Clips cannot be locked or unlocked when media is write
protected.
To lock clips
1
On a clip list screen, select the clips that you want to
lock (multiple selections possible).
This step is not needed if you lock all clips.
2
Display the Clip Menu.
3
Select Lock Unlock Clips.
The Lock Unlock Clips screen appears.
4
Select Lock Selected Clips or Lock All Clips, and then
press the PUSH SET knob.
The clips selected in step 1 or all clips are locked.
A lock icon (see page 62) appears on the thumbnail of
the locked clips.
You can lock the selected clips by pressing the STOP
button while holding down the SHIFT button in step 1.
To unlock clips
1
Execute steps 1 to 3 in “To lock clips” (page 68).
2
Select Unlock Selected Clips or Unlock All Clips, and
then press the PUSH SET knob.
3
Select “OK”, and then press the PUSH SET knob.
When you select a clip you want to unlock on the clip list
screen and then press the STOP button while holding down
the SHIFT button, a dialog appears asking you to confirm
unlock. When you select “OK” and press the PUSH SET
knob, the selected clip is unlocked. (To cancel unlock,
select “CANCEL” and press the PUSH SET knob.)
Deleting clips
• Clips cannot be deleted when media is write protected.
• Locked clips cannot be deleted.
1
On a clip list screen, select the clips that you want to
delete (multiple selections possible).
This step is not needed if you delete all clips.
2
Display the Clip Menu.
3
Select Delete Clips.
The Delete Clips screen appears.
4
Select Delete Selected Clips or Delete ALL Clips, and
then press the PUSH SET knob.
5
Select “OK”, and then press the PUSH SET knob.
The clips selected in step 1 or all clips are deleted.
You can delete the selected clips simply and easily by
pressing the RESET button while holding down the SHIFT
button in step 1 and by carrying out step 5.
Notes
Tip
Tip
Notes
Tip
69
EDL Editing
Chapter 5 Operations on Clip List Screens
Copying clips
See “Copy operations” (page 56) for information about
operations.
Setting the index picture frame
The clip thumbnail screen displays thumbnails as index
pictures for clips. Normally the index picture is the first
frame in a clip, but you can change it to any frame in the
clip for a different index picture.
You cannot set index pictures for EDLs.
1
On the basic operation screen or video monitor screen,
play back the clip for which you want to set the index
picture frame.
2
Press the STOP button at the frame you want to be the
index picture frame, to obtain a still frame display.
3
Display the P5 OTHER page of the function menu,
and press the INDEX function button (F1).
A confirmation box appears asking you whether to set
the frame of the still image as the index picture frame.
4
To set the current frame as the index picture frame,
select “OK” and press the PUSH SET knob.
To set another frame as the index picture frame
Select “CANCEL” and press the PUSH SET knob,
turning the confirmation box off. Start again from
step 1.
When you switch the display to the clip list screen, the
newly set index picture is displayed as the thumbnail.
EDL Editing
What is EDL editing?
EDL editing is a function which allows you to select
material (clips) from the material recorded on media and
perform cut editing. You can do this by operating on this
unit only.
• EDL editing is a convenient way to perform cut editing
in the field and in other offline situations.
• In EDL editing you create an EDL (editing list). Since
the material itself is not affected, you can repeat this any
number of times.
• You can play back the edit list created on this unit.
• Using the EDL editing function, you can easily perform
functions with this unit, such as add entire clips, add
partial clips, and delete sub clips.
• Changing the sequence of sub clips and modifying the
IN/OUT points are not supported.
• An EDL (editing list) can be used on XPRI and other
full-feature nonlinear editing systems.
Clips
Material recorded on a disc with this unit is managed in
units called “clips”. A clip contains the material from a
recording start point to a recording end point.
Clips have numbers beginning with C, for example C0001.
EDLs
You can use the EDL editing function to select clips from
the clips saved on a disc and create a cut edit list called an
“EDL”.
EDLs have numbers beginning with E, for example E0001.
Up to 99 clip lists can be saved on a disc.
Sub clips (clips in EDLs)
Clips (or parts of clips) that have been added to an EDL are
called “sub clips”. Sub clips are virtual editing data that
specify ranges in the original clips. You can use them
without modifying the original data.
The following figure illustrates the relation between clips
and sub clips.
Note
Recording
start point of
clip 2
Recording
end point of
clip 2
Clip 1
(C0001)
Clip 2
(C0002)
Clip 3
(C0003)
Clip 4
(C0004)
70 EDL Editing
Chapter 5 Operations on Clip List Screens
In the above example, the whole of clip 2 has been added
as sub clip 1, and the whole of clip 4 has been added as sub
clip 2.
Sub clip 3 is part of clip 3. Therefore, when EDL E0001 is
played back, clip 4 is played after clip 2, and then the part
of clip 3 shown in gray color is played.
EDL editing (current EDL)
To edit an EDL on a disc, you must first select the target
EDL for editing. Existing EDLs and newly created EDLs
can be selected. The target EDL for editing is called the
“current EDL”.
EDLs are automatically saved on a disc when they are
created and modified.
The current EDL icon is displayed in the status display
area on the clip list screen (thumbnail view) when the
current EDL is selected.
EDL playback
Clips and EDLs are saved together on a disc.
To play an EDL, load the EDL that you want to play, and
press the PLAY button. Clips are played according to the
data in the EDL.
Creating and editing EDLs
The following table lists the steps in the creation and
editing of EDLs with the EDL editing function. To create
an EDL, you always need to carry out the steps inside the
heavy lines. Other steps can be carried out as required.
To create an EDL
You can select multiple clips on the clip list screens and
then create a new EDL. You can also create a new EDL by
assigning an IN point/OUT point on the video monitor
screen.
Creating an EDL on the clip list screens
See page 59 for information about screen operations.
1
On a clip list screen, select the clips that you want to
become sub clips (multiple selections possible).
2
Press and hold the SHIFT button and then press the
PUSH SET knob or display the P1 EDL page of the
Clip F menu and press the CREATE NEW EDL
function button (F3).
The EDL creation starts.
The name for the created EDL appears when the
creation finishes. The created EDL becomes the
current EDL.
3
Select “OK”, and then press the PUSH SET knob.
Creating an EDL on the video monitor screen
You can create an EDL while checking the video on the
video monitor screen by specifying the range to use as a
sub clip. You can perform this operation during recording,
playback (including when stopped), and searching.
During recording, the currently recording clip cannot be
used as a sub clip to create a new EDL, but IN/OUT points
can still be set.
1
On the video monitor screen, cue the frame you want
to specify for the IN point.
2
Press and hold the B/IN button, and then press the
PUSH SET knob.
The IN/OUT setting window appears on the bottom
right.
The time code for the IN point is displayed in the IN/
OUT setting window, and the IN indicator is lit.
Clip 1
(C0001)
Clip 2
(C0002)
Clip 3
(C0003)
Clip 4
(C0004)
EDL (E0001)
Sub clip 1 Sub clip 2 Sub clip 3
Clips on a disc
Current EDL icon
1Create EDLs: Use the CREATE NEW EDL command to
create an EDL containing the selected clips.
2Add sub clips: Use the ADD TO CURT.EDL command
to add the clips you want to use to an EDL. You can
add up to 300 sub clips to one EDL.
3Delete sub clips: Use the REMOVE command to delete
specified sub clips from an EDL.
4Play the EDL: Use the PLAY button and other playback
controls to play the current EDL and check its
contents.
71
EDL Editing
Chapter 5 Operations on Clip List Screens
3
Cue the frame you want to specify for the OUT point.
4
Press and hold the b/OUT button, and then press the
PUSH SET knob.
The IN/OUT setting window appears on the bottom
right.
The time codes for the OUT point and duration (DUR)
are displayed in the IN/OUT setting window, and the
OUT indicator is lit.
5
Press the PAGE/HOME button to display the function
menu, and press the CREATE NEW EDL function
button (F3).
The EDL creation starts.
The name for the created EDL appears when the
creation finishes. The created EDL becomes the
current EDL.
When the current EDL is specified, the current EDL
icon appears in the status display area.
6
Select “OK”, and then press the PUSH SET knob.
To add sub clips to an existing EDL
Sub clips can be added from the clip list display screens or
the video monitor screen. The added clips are inserted at
the end of the EDL.
Sub clips are added to the current EDL. Consequently, an
EDL must be selected as the current EDL in order to
perform this operation. An EDL is made the current EDL
automatically after it is created, as explained in “To create
an EDL” (page 70), allowing sub clips to be added
immediately to the EDL. You can determine whether the
current EDL is selected or not by checking whether the
current EDL icon is displayed or not in the status display
area. If the current EDL is not specified, you must select an
existing EDL as the current EDL using the following
procedure before you can add sub clips.
1
Select an EDL on a clip list screen.
2
Display the P1 EDL page of the Clip F menu and press
the SET CURT.EDL function button (F1).
The selected EDL becomes the current EDL.
When the current EDL is specified, the current EDL
icon appears in the status display area.
Adding on clip list screens
See page 59 for information about screen operations.
1
On a clip list screen, select the clip to add as a sub clip
(multiple selections possible).
2
Press and hold the SHIFT button and press the PUSH
SET knob or display the P1 EDL page of the Clip F
menu then press the ADD TO CURT.EDL function
button (F4).
The sub clip addition starts. When addition is finished,
the screen displayed during execution disappears and
returns to the clip list screen. Adding a sub clip
simultaneously saves the EDL.
The clip is added to the end of the current EDL. The
current EDL remains selected.
Adding in the video monitor screen
When checking the image on the video monitor screen, a
range to use as a sub clip can be specified and added to the
current EDL. This operation is supported during playback
(including when stopped) and when searching. During
recording, the currently recording clip cannot be added as
a sub clip to the current EDL, but IN/OUT points can still
be set.
1
On the video monitor screen, cue the frame you want
to specify for the IN point.
2
Press and hold the B/IN button, and then press the
PUSH SET knob.
The IN/OUT setting window appears on the bottom
right of the display.
The timecode for the IN point is displayed in the IN/
OUT setting window, and the IN indicator is lit.
IN indicator
OUT indicator
72 EDL Editing
Chapter 5 Operations on Clip List Screens
3
Cue the frame you want to specify for the OUT point.
4
Press and hold the b/OUT button, and then press the
PUSH SET knob.
The IN/OUT setting window appears on the bottom
right of the display.
The timecodes for the OUT point and duration (DUR)
are displayed in the IN/OUT setting window, and the
OUT indicator is lit.
5
Press the STOP button.
6
Press the PAGE/HOME button to display the function
menu, and press the ADD TO CURT.EDL function
button (F4).
The sub clip addition starts. When addition is finished,
the screen displayed during execution disappears and
returns to the video monitor screen. Adding a sub clip
simultaneously saves the EDL.
The clip is added to the end of the current EDL. The
current EDL remains selected.
To delete sub clips
This operation is performed on the chapter thumbnail
screen.
1
On the chapter thumbnail screen, select the thumbnails
for the sub clips you want to delete (multiple selections
possible).
2
Press the PAGE/HOME button to display the function
menu, and press the REMOVE function button (F4).
A confirmation message appears asking whether to
execute the delete operation.
3
Select “OK”, and then press the PUSH SET knob. To
abort, select “Cancel”.
To play an EDL
1
On the chapter thumbnail screen, select the thumbnail
for the sub clip you want to start playing.
To start playing from the first frame of the EDL
Select the thumbnail for the first sub clip.
2
Press the PLAY button.
To release the current EDL
This operation clears the current EDL from the memory in
this unit. This operation is performed on clip list screens.
Releasing the current EDL after editing is finished
prevents changes to the settings due to incorrect operation.
1
On a clip list screen, display the P1 EDL page of the
Clip F menu.
2
Press the RELEASE CURT.EDL function button (F2).
A confirmation message appears asking you whether
to execute the release operation.
3
Select “OK”, and then press the PUSH SET knob.
The current EDL is released and the current EDL icon
is removed from the status display area.
To reference the current EDL
Referencing the current EDL displays the chapter
thumbnail screen for the current EDL. This operation is
performed on clip list screens.
1
Display the P1 EDL page of the Clip F menu.
2
Press the GOTO CURT.EDL function button (F6).
The currently specified current EDL is displayed on
the chapter thumbnail screen.
IN indicator
OUT indicator
73
Disc Operations
Chapter 5 Operations on Clip List Screens
Disc Operations
Checking the disc information
1
On a clip list screen, press the MENU button to display
the Clip menu.
2
Select “Media Properties”, and then press the PUSH
SET knob.
The properties screen for the selected disc appears.
Media: DISC/Clip
User Media ID: User media ID
Title1: Title 1
Title2: Title 2
Full Capacity: Total capacity
Rec Remain: Remaining capacity for recording
Rewrite: Number of times the disc has been rewritten
WR protect Tab: Status of the Write Inhibit tab
To display hidden text
For items displaying b or B, press the B/IN or b/OUT
button to scroll the text by one character at a time.
Pressing the V/MARK1 or v/MARK2 button displays the
first character or last character, respectively.
To return to the previous screen
Press the PUSH SET knob.
Formatting (initializing) discs
You can format recorded discs.
Finalized discs cannot be formatted.
1
Insert the disc you want to format into the disc slot.
2
Switch the display to the clip list screen.
3
Press the MENU button to display the Clip Menu.
4
Select “Format Media” and press the PUSH SET knob.
A confirmation message appears asking you whether
to execute formatting.
5
To execute formatting, select “OK” and press the
PUSH SET knob.
The formatting starts, and the message “Format
Executing...” appears.
To cancel the formatting
Select “CANCEL” and press the PUSH SET knob.
When the formatting is completed, the message
“Format was successful.” appears.
To format another disc
Remove the disc that has been formatted, and insert
another disc into the disc slot. When the confirmation
message appears asking if you want to execute
formatting, execute step 5 once more.
6
To quit formatting, select “Exit” and press the PUSH
SET knob.
Finalizing discs
You can finalize write-once type Professional Discs.
• You cannot write additional data to finalized discs.
• Finalized discs cannot be finalized again.
1
Insert the disc you want to finalize into the disc slot.
2
Switch the display to the clip list screen.
3
Press the MENU button to display the Clip Menu.
4
Select “Finalize Disc” and press the PUSH SET knob.
A confirmation message appears asking you whether
to execute finalizing.
5
To execute finalizing, select “OK” and press the
PUSH SET knob.
The finalizing starts, and the message “Finalize
Executing...” appears.
To cancel the finalizing
Select “CANCEL” and press the PUSH SET knob.
When the finalizing is completed, the message
“Finalize completed.” appears.
Note
Notes
74 Disc Operations
Chapter 5 Operations on Clip List Screens
To finalize another disc
Remove the disc that has been finalized, and insert
another disc into the disc slot. When the confirmation
message appears asking if you want to execute
finalizing, execute step 5 once more.
6
To quit finalizing, select “Exit” and press the PUSH
SET knob.
Repairing discs
If a disc is not recognized correctly, you can repair the disc
for use by rebuilding the disc management data.
The repair operation can also be executed on normal discs
without problem.
This function is provided in order to recover recorded
material from discs in cases of unforeseen trouble, but it
does not represent a 100% guarantee of data recovery.
1
Insert the disc you want to repair into the disc slot.
2
Switch the display to the clip list screen.
The clip list may not be displayed if there is an error
with the disc.
3
Press the MENU button to display the Clip Menu.
4
Select “Update/Restorings Media” and press the
PUSH SET knob.
A confirmation message appears asking you whether
to execute repairing.
5
To execute repairing, select “OK” and press the PUSH
SET knob.
The repairing starts, and the message “Update/Restore
Executing...” appears.
The repair process cannot be interrupted.
When the repairing is completed, the message
“Update/Restore was successful.” appears.
To repair another disc
Remove the disc that has been repaired, and insert
another disc into the disc slot. When the confirmation
message appears asking if you want to execute
repairing, execute step 5 once more.
6
To quit repairing, select “Exit” and press the PUSH
SET knob.
Note
75
Overview
Chapter
Chapter 6 File Operations
6
File Operations
Overview
A remote computer can be connected to this unit and used
to operate on recorded data which has been saved in data
files, such as video and audio data files.
To perform file operations, use either of the following
methods to interconnect this unit and a computer.
• Make FTP connections (see page 79).
• Make CIFS connections (see page 84).
• Discs inserted in this unit cannot be displayed or
operated on the unit while there is a remote connection
using FTP/CIFS from an external device.
• When disc restoration is necessary after FTP or CIFS
connections are terminated, the restoration is
automatically executed on this unit.
• Do not play back a clip during operation using a network
connection. The output may become distorted or muted.
Directory structure
The following figure shows an example of the directory
structure visible to the computer connected to this unit. FTPS protocol support
The unit supports the FTP and FTPS protocols.
The FTPS protocol is recommended when using the unit in
an insecure network environment.
Notes
a) Root directory
76 Overview
Chapter 6 File Operations
File operation restrictions
This section explains which operations are possible on
files stored in each directory.
When required, the following operation tables distinguish
reading and writing from partial reading and writing.
Read: Read data sequentially from the start to the end of
the file.
Partial read: Read only a part of the data in the file.
Write: Write data sequentially from the start to the end of
the file.
Partial write: Write data to a part of the file only.
File names are not case-sensitive.
Root directory
a) Only during CIFS connections
b) Only files which can be written by XDCAM
• Directories cannot be created in the root directory.
• The directories in the root directory (Clip, Edit, Sub,
General, UserData, and PROAV) cannot be deleted or
renamed.
• When connected by CIFS, the General and UserData
directories are read only.
Clip directory
Note
File name Content Operations
Read/Partial
read a) Write/Partial
write a) Rename Create Delete
INDEX.XML Contains data for management of the material
on the disc.
Ye s N o N o N o N o
ALIAS.XML Contains conversion tables for assigning user-
defined names to clips and clip lists.
Ye s N o N o N o N o
DISCMETA.XML Contains metadata to indicate the disc
properties.
Ye s Ye s b) No No No
MEDIAPRO.XML Contains a list of material on the disc, basic
properties, related information, and information
about access methods.
Ye s N o N o N o N o
SYSPRO.XML Contains information about device system
settings and menu settings.
Ye s N o N o N o N o
Other files Files other than the above – No – No –
Notes
File name Content Operations
Read/Partial
read a)
Write/Partial
write a)
Rename Create Delete
C*.MXF b) Clip file creating during recording (MXF file)
*: 0001 to 9999
Ye s Ye s c), d) Ye s Ye s c) Ye s e)
C*M01.XML b) Metadata file generated automatically when
C*.MXF file is created.
*: 0001 to 9999
Ye s Ye s f) No g) No h) No i)
C*M02.KLV b) User metadata file. This type of file is
generated automatically during recording via
an FTP connection when the unit recognizes
that an MXF file contains metadata that was
generated by a non-XDCAM device.
*: 0001 to 9999
Ye s Ye s d) No g) Ye s f) Ye s i)
Other files Files other than the above – No – No –
77
Overview
Chapter 6 File Operations
a) Only during CIFS connections
b) The unit can handle files with user-defined names in the “C*” part.
c) Only files which are 2 seconds or longer in length, in a format matching
the format (system frequency) and recording format (MPEG HD and
number of audio channels) of the recorded sections of the disc, and which
can be overwritten by XDCAM. (Partial writing is not possible.)
d) Overwriting is not possible.
e) Any clip may be selected and deleted.
f) Only files which can be written by XDCAM
g) When the “C*” part of a C*.MXF file name is changed, a C*M01.XML
file and a C*M02.KLV file with the same name in the “C*” part are also
changed automatically.
h) When a C*.MXF file is created, a C*M01.XML file with the same name
in the “C*” part is created automatically.
i) When a C*.MXF file is deleted, a C*M01.XML file and a C*M02.KLV
file with the same name in the “C*” part are also deleted automatically.
Directories cannot be created in the Clip directory.
Edit directory
a) Only during CIFS connections
b) The unit can handle files with user-defined names in the “E*” part.
c) Only files which can be written by XDCAM. Partial writing is not
possible.
d) Only files which can be written by XDCAM
e) When the “E*” part of an “E*01.SMI” file name is changed, an
E*M01.XML file with the same name in the “E*” part is also changed
automatically.
f) When an E*E01.SMI file is created, an E*M01.XML file with the same
name in the “E*” part is also generated automatically.
g) When an E*E01.SMI file is deleted, an E*M01.XML file with the same
name in the “E*” part is also deleted automatically.
Directories cannot be created in the Edit directory.
Sub directory
a) Only during CIFS connections
b) The unit can handle files with user-defined names in the “C*” part.
c) When the “C*” part of a C*.MXF file name is changed, a C*S01.MXF file
with the same name in the “C*” part is changed automatically.
d) When a C*.MXF file is created, a C*S01.XML file with the same name in
the “C*” part is generated automatically.
e) When a C*.MXF file is deleted, the C*S01.XML file with the same name
in the “C*” part is also deleted automatically.
Directories cannot be created in the Sub directory.
General directory
Note
File name Content Operations
Read/Partial
read a)
Write/Partial
write a)
Rename Create Delete
E*E01.SMI b) Clip list file
*: 0001 to 0099
Ye s Ye s c) Ye s Ye s d) Ye s
E*M01.XML b) Metadata file generated automatically when
E*E01.SMI file is created.
*: 0001 to 0099
Ye s Ye s c) No e) No f) No g)
Other files Files other than the above – No – No –
Note
File name Content Operations
Read/Partial
read a)
Write/Partial
write a)
Rename Create Delete
C*S01.MXF b) Proxy AV data (MXF) file generated
automatically when a C*.MXF file is created.
*: 0001 to 9999
Ye s N o N o c) No d) No e)
Other files Files other than the above – No – No –
Note
File name Content Operations
Read/Partial
read a)
Write/Partial
write a)
Rename Create Delete
Any file Yes Yes Yes b) Ye s Ye s
78 Overview
Chapter 6 File Operations
a) Only during CIFS connections
b) UTF-8 file names can be up to 63 bytes in length. (Depending on the
character type, file names (including extension) may be limited to 21
characters.)
The following directory operations are possible in the
General directory.
• Directory creation (up to 63 levels, including the
General directory)
• Deletion and renaming of directories
• The maximum number of files that can be created on a
disc is 5,000 for single-layer discs, 6,000 for dual-layer
discs, and 20,000 for triple-layer and quad-layer discs
(including directories).
• File names and directory names can use letters, numbers,
and symbols from the Unicode 2.0 (UTF-8) character
set.
However, the following control characters and symbols
cannot be used.
- Control characters: U+0000 to U+001F, U+007F
- Symbols: ", *, /, :, <, >, ?, \, |
UserData directory
a) Only during CIFS connections
b) UTF-8 file names can be up to 63 bytes in length. (Depending on the
character type, file names (including extension) may be limited to 21
characters.)
The following directory operations are possible in the
UserData directory.
• Directory creation (up to 62 levels, including the
UserData directory)
• Deletion and renaming of directories
XDROOT and BPAV folders
An XDROOT folder or BPAV folder will be created in the
UserData directory when using this unit or Content
Browser to copy to or from the UserData directory.
Folders, files, and other data making up the clips are stored
in the XDROOT and BPAV folders, and modifying the
data in these folders using a device other than this unit or
Content Browser may render the clips inoperable. Always
use this unit or Content Browser to modify clips in the
XDROOT and BPAV folders.
PROAV directory
This directory contains individual files recorded on the
disc.
To display the PROAV directory, set maintenance menu
item M33 FILE I/F CONFIG > PROAV DISPLAY to
“enable”.
For details, see maintenance menu item M33 (page 104).
Notes
File name Content Operations
Read/Partial
read a) Write/Partial
write a) Rename Create Delete
Any file Yes Ye s Ye s b) Ye s Ye s
79
FTP File Operations
Chapter 6 File Operations
FTP File Operations
File operations between this unit and a remote computer
can be carried out by the File Transfer Protocol (FTP).
Preparations
1
Connect the network connectors of this unit and a
remote computer with a network cable (see
connections illustration on page 27). Or connect this
unit to the network to which the remote computer is
connected (see connections illustration on page 27).
2
Set the IP address and other network setting items for
this unit. 1)
For details, see M5: NETWORK of the maintenance
menu (page 107).
If network settings have already been made
Check the IP address of this unit.
For details, see M5: NETWORK of the maintenance
menu (page 107).
1) This unit is able to acquire an IP address automatically from a DHCP
server. It also supports an Auto-IP function to assign an IP address
automatically when access from this unit to the DHCP server times
out. You can check DHCP settings and the assigned IP address with
maintenance menu item M51 IP ADDRESS.
To connect a computer running Windows 7/
Windows 8/Windows 10
Disable the Internet Protocol Version 6 (TCP/IPv6).
Windows 7: (1) Open “View network status and
tasks” >“Change adapter settings” >“Local Area
Connection” in the control panel. (2) In the
“Local Area Connection Properties”, uncheck the
“Internet Protocol Version 6 (TCP/IPv6)”, and
then click the “OK” button.
Windows 8: (1) Open “View network status and
tasks” >“Change adapter settings” >“Ethernet” in
the control panel. (2) In the “Ethernet Properties”,
uncheck the “Internet Protocol Version 6 (TCP/
IPv6)”, and then click the “OK” button.
Windows 10: (1) Open “Control Panel.” (2) Select
“Network and Internet” > “Network and Sharing
Center” > “Change adapter settings”. (3) Right-
click the network connection of the computer and
select “Properties”. (4) Uncheck “Internet
Protocol Version 6 (TCP/IPv6)”, and then click
the OK button.
3
Set the remote control switch to “NET” (see page 11).
Making FTP connections
FTP connections between this unit and a remote computer
can be made with either of the following.
• The command prompt
•FTP client software
This section explains how to use the command prompt. For
more information about using FTP client software, refer to
the documentation of the FTP client software on your
system.
To log in
1
Put the unit into the following state.
• Recording, playback, search and other disc
operations (see page 48): Stopped
• Display screen: Other than the clip list screen (see
page 59)
2
Start the command prompt.
3
Enter “ftp <SP> <IP address>”, and press the Enter
key. (<SP> refers to a space.)
For example, if the IP address of this unit is set to
“192.168.001.010”, enter “ftp 192.168.1.10”.
Refer to the Windows help for more information about
the FTP command.
If the connection succeeds, you are prompted to enter
a user name.
4
Enter the user name “admin” and press the Enter key.
When the user name is verified, you are prompted to
enter a password.
5
Enter the password and press the Enter key.
The password is set to the model name (“pdw-
hd1550”) when the unit is shipped from the factory.
The login is complete when the password is verified.
See page 80 for the FTP protocol commands
supported by this unit.
If the connection times out
This unit terminates FTP connections if no command
is received within 90 seconds of the last command. If
this occurs, log out (see page 80) and repeat steps 2 to
4.
If you power this unit off during an FTP connection,
the data transferred thus far is discarded.
Note
80 FTP File Operations
Chapter 6 File Operations
To log out
To log out after finishing file operations, enter “QUIT” at
the command prompt and press the Enter key.
Command list
The FTP protocol commands supported by this unit
include standard commands (see page 80) and extended
commands (see page 82).
• To execute FTP commands, you must install application
software with FTP function on your computer.
• The commands supported by application software vary.
• An FTP client that supports UTF-8 is required to use
Unicode characters other than ASCII characters.
Command prompt FTP commands do not support
UTF-8.
Standard commands
In the command syntax, <SP> means a space, entered by
pressing the space bar, and <CRLF> means a new line,
entered by pressing the Enter key.
USER
Send this command to begin the login process.
Command syntax: USER <SP> <user name> <CRLF>
Input example: USER admin
PASS
After sending the USER command, send this command to
complete the login process.
Command syntax: PASS <SP> <password> <CRLF>
Input example: PASS pdw-hd1550
QUIT
Terminates the FTP connection. If a file is being
transferred, terminates after completion of the transfer.
Command syntax: QUIT <CRLF>
PORT
Specifies the IP address and port to which this unit should
connect for the next file transfer (for data transfer from this
unit).
Command syntax: PORT <SP> <h1,h2,h3,h4,p1,p2>
<CRLF>
• h1 (most significant byte) to h4 (least significant byte): IP
address
• p1 (most significant byte), p2 (least significant byte): Port
number
Input example: PORT 10,0,0,1,242,48
(IP address: 10.0.0.1, Port number: 62000)
PASV
This command requests this unit to “listen” on a data port
(which is not its default data port). (It puts this unit into
passive mode, waiting for the remote computer to make a
data connection.)
Command syntax: PASV <CRLF>
TYPE
Specifies the type of data to be transferred.
Command syntax: TYPE <SP> <type-code (options
delimited by <SP>)> <CRLF>
<type-code> can be any of the following. However, for
XDCAM, data is always transferred as “I”, regardless of
the type-code specification.
•A: ASCII
- N: Non-print
- T: Telnet format
- C: ASA Carriage Control
• E: EBCDIC
- N: Non-print
- T: Telnet format
- C: ASA Carriage Control
• I: IMAGE (Binary) (default)
• L: LOCAL BYTE
- SIZE: Byte size
Input example: TYPE I
STRU
Specifies the data structure.
Command syntax: STRU <SP> <structure-code>
<CRLF>
<structure-code> can be any of the following. However,
for XDCAM, the structure is always “F”, regardless of the
structure-code specification.
• F: File structure (default)
• R: Record structure
• P: Page structure
Input example: STRU F
MODE
Specifies the transfer mode.
Command syntax: MODE <SP> <mode-code> <CRLF>
<mode-code> can be any of the following. However, for
XDCAM, the mode is always “S”, regardless of the mode-
code specification.
• S: Stream mode (default)
Notes
81
FTP File Operations
Chapter 6 File Operations
• B: Block mode
• C: Compressed mode
Input example: MODE S
LIST
Sends a list of files from this unit to the remote computer.
Command syntax: LIST <SP> <options> <SP> <path-
name> <CRLF>
<options> can be any of the following.
• -a: Also display file names that begin with “.”
• -F: Append “/” to directory names.
The following data is transferred, depending on whether
<path-name> specifies a directory or file.
• Directory specified: A list of the files in the specified
directory
• File specified: Information about the specified file
• No specification: A list of the files in the current directory
The wildcard characters “*” (any string) and “?” (any
character) may be used in <path-name>.
Input example 1: LIST-a Clip
Input example 2: LIST Clip/*.MXF
NLST
Sends a list of file names from this unit to the remote
computer, with no other information.
Command syntax: NLST <SP> <options or path-name>
<CRLF>
The following options may be specified when no path-
name is specified.
• -a: Also display file names that begin with “.”.
• -l: Display information other than file name (gives the same
result as the LIST command).
• -F: Append “/” to directory names.
The following data is transferred, depending on whether
<path-name> specifies a directory or file.
• Directory specified: A list of the file names only in the
specified directory
• No specification: A list of the file names only in the current
directory.
The wildcard characters “*” (any string) and “?” (any
character) may be used in <path-name>.
Input example 1: NLST-l
Input example 2: NLST Clip/*.MXF
RETR
Begins transfer of a copy of a file in the specified path on
this unit to the current directory on the remote computer.
Command syntax: RETR <SP> <path-name> <CRLF>
Input example: RETR Clip/C0001.MXF
STOR
Begins transfer of a copy of a file in the specified path on
the remote computer to the current directory on this unit.
Command syntax: STOR <SP> <path-name> <CRLF>
Input example: STOR Edit/E0001E01.SMI
RNFR
RNTO
Renames a file.
Specify the file to be renamed with the RNFR command,
and specify the new name with the RNTO command.
(Always follow a RNFR command with a RNTO
command.)
For details, see “File operation restrictions” (page 76).
Command syntax: RNFR <SP> <path-name (before
change)> <CRLF>
RNTO <SP> <path-name (after change)> <CRLF>
Input example: RNFR General/info.txt
RNTO General/clip_info.txt
DELE
Deletes the specified file on this unit.
Depending on the directory and file type, deletion may not
be possible.
For details, see “File operation restrictions” (page 76).
Command syntax: DELE <SP> <path-name> <CRLF>
Input example: DELE Clip/C0099.MXF
STAT
Sends information about properties of the specified file
from this unit to the remote computer.
Command syntax: STAT <SP> <path-name> <CRLF>
The following data is transferred, depending on whether a
file is specified with <path-name>.
• File specified: The properties of the specified file
• No specification: 0
Input example: STAT Clip/C0001.MXF
SYST
Displays the system name of this unit.
Command syntax: SYST <CRLF>
Note
82 FTP File Operations
Chapter 6 File Operations
HELP
Displays a list of the commands supported by this unit, or
an explanation of the specified command.
Command syntax: HELP <SP> <command-name>
<CRLF>
The following data is transferred, depending on whether a
command name is specified with <command-name>.
• Command name specified: Explanation of the specified
command.
• No specification: Command list
Input example: HELP RETR
NOOP
Does nothing except return a response. (Used to check
whether this unit is running.)
Command syntax: NOOP <CRLF>
PWD
Displays the current directory (“/” if the directory is the
root directory).
Command syntax: PWD <CRLF>
CWD
Changes the current directory (moves from the current
directory to another directory).
Command syntax: CWD <SP> <path-name> <CRLF>
Moves to a directory as follows, depending on whether a
directory is specified with <path-name>.
• Directory specified: To the specified directory
• No specification: To the root directory
Input example: CWD General
CDUP
Moves one level up in the directory structure (makes the
parent of the current directory be the current directory).
Command syntax: CDUP <CRLF>
MKD
Creates a new directory.
Command syntax: MKD <SP> <path-name> <CRLF>
RMD
Deletes a directory.
Some limitations apply to the deletion of directories.
For details, see “File operation restrictions” (page 76).
Command syntax: RMD <SP> <path-name> <CRLF>
STOU
Transfers the specified file, similar to STOR, but changes
the file name if a file with the same name already exists at
the destination.
Command syntax: STOU <SP> <path-name> <CRLF>
MDTM
Acquires the date and time of the most recent modification
of the file in the format “YYYYMMDDhhmmss” (YYYY:
year, MM: month, DD: day, hh: hour, mm: minute, ss:
second).
Command syntax: MDTM <CRLF>
SIZE
Acquires the size of the file at the specified path on the
unit.
Command syntax: SIZE <SP> <path-name> <CRLF>
Input example: SIZE Clip/C0001.MXF
Extended commands
In the Command syntax, <SP> means a space, entered by
pressing the space bar, and <CRLF> means a new line,
entered by pressing the Enter key.
SITE DF
Displays the remaining space of the applicable media in
the current directory.
Command syntax: SITE DF<CRLF>
SITE_MEID
Displays the ID of the applicable media in the current
directory.
Command syntax: SITE_MEID<CRLF>
SITE CHMOD
Locks and unlocks clips. Also sets permissions for
directories and files.
Command syntax: SITE CHMOD <SP> <flag> <SP>
<path-name> <CRLF>
Specify one of the following values in <flag>, according to
the specification in <path-name>.
• When a clip is specified in <path-name>
- 444: Lock.
- 666: Unlock.
• When a directory is specified in <path-name>
- 555: Forbid writing to the directory.
- 777: Allow writing to the directory.
Note
83
FTP File Operations
Chapter 6 File Operations
• When a file is specified in <path-name>
- 444: Forbid writing to and execution of the file.
- 555: Forbid writing to the file, but allow execution.
- 666: Allow writing to the file, but forbid execution.
- 777: Allow writing to and execution of the file.
Input example: SITE CHMOD 444 Clip/C0001.MXF
(Lock clip C0001.MXF)
SITE REPF
Sends a portion of a copy of the file specified on the unit
to a computer.
Command syntax: SITE REPF <SP> <path-name> <SP>
<start frame> <SP> <transfer size> <CRLF>
SITE REPFL
Sends a portion of a copy of the file specified on the unit
to a computer.
(When the path name includes spaces)
Command syntax: SITE REPFL <SP> <path-name> <SP>
<start frame> <SP> <transfer size> <CRLF>
SITE UMMD
When preceding the STOR command, this command saves
the UMID of the copy source file.
Command syntax: SITE UMMD <CRLF>
SITE TCPR
Presets the starting timecode value recorded with the
STOR or STOU command.
Command syntax: SITE TCPR <timecode> <CRLF>
The timecode specified in <timecode> is preset.
The timecode format is “ffssmmhh”.
(ff: frame; ss: second; mm: minute; hh: hour)
SITE FUNC
Acquires the function and version of the extended
commands.
Command syntax: SITE FUNC <CRLF>
Information is displayed in the following format.
<main function> <SP> <branch function> <SP> <branch
function version>
For XDCAM, sent in a format like “200 MXF DISK 1”
(“200” is a response code).
SITE FSTS
Acquires the file system status of this unit.
Command syntax: SITE FSTS <CRLF>
One of the following status codes is displayed.
• 0: Initial state, or no disc is loaded.
• 1: File system mount is OK
• 3: File system mount is not OK
84 CIFS File Operations
Chapter 6 File Operations
CIFS File Operations
You can perform file operations using the Common
Internet File System (CIFS) between this unit and the
computer.
Preparations
See “Preparations” under “FTP File Operations”
(page 79).
Making CIFS connections
CIFS connections between this unit and a Windows
computer can be made with either of the following.
• Use Windows Explorer to map this unit as a network
drive
• Refer to this unit directly from Windows Explorer
The following describes the procedure for using Windows
Explorer to map this unit as a network drive.
Operations may vary depending on the version of
Windows you are using.
1
Start Windows Explorer.
2
In the Tools menu, select “Map Network Drive...”.
The “Map Network Drive” dialog appears.
3
Enter “\\<IP address>\xdcam\” in the “Folder” field.
For example, if the IP address of this unit is set to
“192.168.001.010”, enter “\\192.168.1.10\xdcam\”.
4
Click on “Connect using a different user name.”.
The “Connect As...” dialog appears.
5
Enter the user name “admin” and the password, and
click “OK”.
The password is set to the model name (“pdw-
hd1550”) when the unit is shipped from the factory.
6
Click “Finish”.
The network drive allocation is complete when the
password is verified.
To break the connections
In Windows Explorer, select the network drive and right-
click it, then click “Disconnect”.
Note
85
Menu System Configuration / Setup Menu
Chapter
Chapter 7 Menus
7
Menus
Menu System
Configuration
The settings for this unit use the following menus.
Setup menu
The setup menu system of this unit comprises the basic
setup menu and extended setup menu.
Function menu
For details, see “Basic Operations of the Function Menu”
(page 39).
Clip Menu
For details, see “Clip Menu” (page 64).
Maintenance menu
This provides audio control, and network and setup menu
settings, and also shows version information.
For details, see “Maintenance Menu” (page 104).
Setup Menu
The setup menu system of this unit comprises the basic
setup menu and extended setup menu.
Basic menu
This menu is used to make settings related to, for example,
the operating hours meter, the content and display of text
information, and the menu banks for saving menu settings.
Extended menu
This menu is used to make a wide range of settings relating
to the functions of this unit, for example, the control panel
functions, video and audio control, and digital data
processing.
Maintenance menu item M40 EXTEND MENU must be
set to “ENABLE” in order to display the extended menu.
For details, see maintenance menu item M40 (page 107).
Configuration of the basic menu
The basic menu comprises the following groups of items.
Configuration of the extended menu
The extended menu comprises the following groups of
items.
Item group Function Refer to
Items
H01 to H19
Display the total number of
hours the unit has been
powered on, and other
information collected by the
operating hours meter
page 112
Items
001 to 099
Settings relating to the
superimposed text information,
switching between 59.94i,
59.94P, 29.97P, 50i, 50P and
25P.
page 86
Items
B01 to B20
Settings relating to the menu
banks for saving menu settings
page 89
86 Setup Menu
Chapter 7 Menus
The extended menu appears when maintenance menu item
M40 EXTENDED MENU is set to “ENABLE”.
Items in the basic menu
The basic menu items (excluding the items related to the
operating hours meter) are listed in the following table.
• The values in the “Settings” column are the values that
appear on settings screens. The values in brackets [ ] are
the value shown on menu screens (when they differ from
the values shown on settings screens).
• The underlined values are the factory defaults.
Item group Function Refer to
Items
100 to 199
Settings relating to control
panels
page 92
Items
200 to 299
Settings relating to the remote
control interface
page 94
Items
300 to 399
Settings relating to editing
operations
page 94
Items
500 to 599
Settings relating to disc
protection
page 95
Items
600 to 649
Settings relating to the
timecode generator
page 95
Items
650 to 699
Settings relating to metadata page 96
Items
700 to 799
Settings relating to video
control
page 97
Items
800 to 899
Settings relating to audio
control
page 100
Items
900 to 999
Settings relating to digital
processing
page 101
Item group Function Refer to
Item number Item name Settings
002 CHARACTER H-POSITION Adjust the horizontal screen position (as a hexadecimal value) of the text
information output from the COMPOSITE OUTPUT 2 (SUPER), SDSDI
OUTPUT 2 (SUPER), HDSDI OUTPUT 2 (SUPER), or HDMI OUT connector
for superimposed display on the monitor. The hexadecimal value 00 is for the
far left of the screen. Increasing the value moves the position of the characters
to the right.
00 to 0C to 28 (When the number of system lines is 1080 and the system
frequency is 59.94i, 29.97P, 50i, 25P, or 23.98P)
00 to 0B to 28 (When the number of system lines is 720 and the system
frequency is 59.94P or 50P)
Set this item by adjusting to the required position while viewing the monitor.
003 CHARACTER V-POSITION Adjust the vertical screen position (as a hexadecimal value) of the text
information output from the COMPOSITE OUTPUT 2 (SUPER), SDSDI
OUTPUT 2 (SUPER), HDSDI OUTPUT 2 (SUPER), or HDMI OUT connector
for superimposed display on the monitor. The hexadecimal value 00 is for the
top of the screen. Increasing the value lowers the position of the characters.
00 to 2A to 32 (When the number of system lines is 1080 and the system
frequency is 59.94i, 29.97P, 50i, 25P, or 23.98P)
00 to 29 to 32 (When the number of system lines is 720 and the system
frequency is 59.94P or 50P)
Set this item by adjusting to the required position while viewing the monitor.
005 DISPLAY INFORMATION
SELECT
Determine the kind of text information to be output from the COMPOSITE
OUTPUT 2 (SUPER), SDSDI OUTPUT 2 (SUPER), HDSDI OUTPUT 2
(SUPER), or HDMI OUT connector.
time data & status [T&sta]: Time data and the units status.
time data & UB [T&UB]: Time data and user bits data. (When “UB” (user bits
data) is selected with CNTR SEL on the HOME page of the function
menu, the “user bits data” and “time data” arranged in that order are
displayed.)
time data & CNT [T&CNT]: Time data and counter count. (When “COUNTER”
is selected with CNTR SEL on the HOME page of the function menu, the
counter count and time data arranged in that order are displayed.)
time data & time data [T&T]: Time data and timecode (TC or VITC)
time data only [time]: Time data only
87
Setup Menu
Chapter 7 Menus
006 LOCAL FUNCTION ENABLE Determine which recording and playback control buttons on the front panel are
enabled when this unit is controlled from external equipment.
all disable [dis]: All buttons and switches are disabled.
stop & eject [st&ej]: Only the STOP button and EJECT button are enabled.
all enable [ena]: All buttons and switches are enabled.
local key map [map]: Follows the setting of setup menu item 023 LOCAL
KEY MAP.
009 CHARACTER TYPE Determine the type of characters such as timecode output from the
COMPOSITE OUTPUT 2 (SUPER), SDSDI OUTPUT 2 (SUPER), HDSDI
OUTPUT 2 (SUPER), or HDMI OUT connector for superimposed display on
the monitor.
white: White letters on a black background
black: Black letters on a white background
white/outline [W/out]: White letters with black outline
black/outline [B/out]: Black letters with white outline
011 CHARACTER V-SIZE Determine the vertical size of characters such as timecode output from the
COMPOSITE OUTPUT 2 (SUPER), SDSDI OUTPUT 2 (SUPER), HDSDI
OUTPUT 2 (SUPER), or HDMI OUT connector for superimposed display on
the monitor.
: Standard size
×2: 2 times standard size
Set this item by selecting the required size while viewing the monitor.
012 CONDITION DISPLAY ON
VIDEO MONITOR
Select whether to display disc condition marks in external monitor output
(output from the COMPOSITE OUTPUT 2 (SUPER) connector, SDSDI
OUTPUT 2 (SUPER) connector, HDSDI OUTPUT 2 (SUPER) connector, or
HDMI OUT connector).
disable [dis]: Do not display.
enable [ena]: Display.
013 SYSTEM FREQUENCY
SELECT MENU
Specify whether to enable switching the system frequencies.
off: Do not enable switching the system frequency.
on: Enable switching the system frequency.
You can switch between the following frequencies.
1080/59.94i, 50i, 29.97P, 25P, 23.98P, 720/59.94P, 50P
For details about switching the system frequency, see page 34.
Note
Settings for both basic and extended menu items are saved separately for
different system frequencies.
• 1080 59.94i/29.97P
• 1080 50i/25P
• 1080 23.98P
• 720 59.94P
• 720 50P
Therefore, when you switch the system frequency, all menu items are reset to
the current settings for the new mode. (They are different from the setting for
the previous mode.)
017 SUB STATUS DISPLAY
SELECT
Set whether to display sub-status details on an external monitor (output from
COMPOSITE OUTPUT 2 (SUPER), SDSDI OUTPUT 2 (SUPER), HDSDI
OUTPUT 2 (SUPER), or HDMI OUT connector).
off: Do not output sub-status.
rec remain [recr]: Display the remaining recording time (in minutes) and the
number of clips that can be recorded.
Item number Item name Settings
×
1
88 Setup Menu
Chapter 7 Menus
023 LOCAL KEY MAP When “map” is selected in setup menu item 006 LOCAL FUNCTION ENABLE
and the unit is controlled remotely from another device using the REMOTE(9P)
connector, the operation buttons on the front panel can be operated
independently for each of the following sub-items. The settings below are
available for each sub-item.
disable [dis]: Disable the button function.
enable [ena]: Enable the button function.
Sub-item
1 PLAY Select whether to enable the PLAY button function.
2 REC Select whether to enable the REC button function.
3 STOP Select whether to enable the STOP button function, when the SHIFT button is
not pressed.
4 STANDBY Select whether to enable the STOP button function, when the SHIFT button is
pressed.
5 EJECT Select whether to enable the eject button function.
6 SHUTTLE/JOG Select whether to enable the SHTL/JOG button and shuttle/jog dial functions.
7 VAR/JOG Select whether to enable the VAR/JOG button and shuttle/jog dial functions.
8 NEXT/PREV Select whether to enable the NEXT button and PREV button functions.
9 MENU/F-Key Select whether to enable the MENU button, F1 to F6 button, and RESET/
RETURN button functions.
10 THUMBNAIL Select whether to enable the THUMBNAIL button function.
11 COPY Select whether to enable the COPY button function.
12 MEDIA SELECT Select whether to enable the MEDIA SEL button function.
027 SD CHARACTER Specify whether to superimpose text information on the SD video signal.
Sub-item
1SD-SDI2
a) Specify whether to superimpose text information on the video signal output
from the SDSDI OUTPUT 2 (SUPER) connector.
off: Do not superimpose.
on: Superimpose.
2 COMPOSITE2 a) Specify whether to superimpose text information on the video signal output
from the COMPOSITE OUTPUT 2 (SUPER).
off: Do not superimpose.
on: Superimpose.
3 LCD Specify whether to superimpose text information on the video signal output to
the display on the front panel.
off: Do not superimpose.
on: Superimpose.
028 HD CHARACTER Specify whether to superimpose text information on the HD video signal.
Sub-item
1 HD-SDI2 Specify whether to superimpose text information on the video signal output
from the HDSDI OUTPUT 2 (SUPER) connector.
off: Do not superimpose.
on: Superimpose.
2 HDMI a) Specify whether to superimpose text information on the video signal output
from the HDMI OUT connector when the HDMI output is the same with the SDI
output.
off: Do not superimpose.
on: Superimpose.
029 STORED OWNERSHIP Specify whether to enable changing UMID ownership information settings
(COUNTRY, ORGANIZATION and USER).
off: Do not enable.
on: Enable.
See “Using UMID Data” (page 126) for more information about UMID.
Item number Item name Settings
89
Setup Menu
Chapter 7 Menus
a) Not displayed when the unit is in 23.98P mode.
b) Not displayed when the unit is in 59.94P/50P mode.
Basic menu operations
Setup menus are displayed on the display or on a monitor
connected to the HDMI OUT connector.
To display the setup menu
031 RECORDING FORMAT Set the recording format.
AI422: XAVC Intra 1920×1080 422 b)
HD422: HD422
HD420 HQ [420HQ]: HD420 HQ
HD420 SP [420SP]: HD420 SP a), b)
IMX 50Mbps [IMX50]: MPEG IMX 50 Mbps a)
IMX 30Mbps [IMX30]: MPEG IMX 30 Mbps a)
DVCAM: DVCAM a)
033 BATTERY END VOLTAGE Set the voltage at which to shut down the unit during battery operation. The
battery near end indicator flashes at +0.7 V of the set voltage.
10.5V to 13.5V: 10.5 V to 13.5 V in 0.5 V unit.
036 FILE NAMING Set the clip name to be assigned to a clip to record.
Sub-item
1 PREFIX Set the prefix of the clip name (up to 10 characters). The allowable characters
are alphanumeric characters, symbols (! # $ % & ' ( ) + , - . ; = @ [ ] ^ _ { } ˜),
and the space character.
CLIP
2 NUMERIC Set the initial value of the numeric part (00001 to 99999, five-digit serial
number) of the clip name.
00001
3 AUTO NAMING Specify the clip naming format.
prefix: Generate clip names using PREFIX and NUMERIC.
C****: Generate names in PDW-series standard format. (****: numeric portion)
(File names become C****.MXF with numeric portion in ascending order.)
B01 RECALL SETUP BANK-1 Set to “on” to recall menu bank 1 to replace the current menu settings.
B02 RECALL SETUP BANK-2 Set to “on” to recall menu bank 2 to replace the current menu settings.
B03 RECALL SETUP BANK-3 Set to “on” to recall menu bank 3 to replace the current menu settings.
B11 SAVE SETUP BANK-1 Set to “on” to save current menu settings to menu bank 1.
B12 SAVE SETUP BANK-2 Set to “on” to save current menu settings to menu bank 2.
B13 SAVE SETUP BANK-3 Set to “on” to save current menu settings to menu bank 3.
B20 RESET SETUP MENU Set to “on” to return the settings of the current menu to the factory default
settings.
Item number Item name Settings
MENU button
Function buttons (F1 to F6) PUSH SET knob
RESET button
90 Setup Menu
Chapter 7 Menus
To display a setup menu, press the MENU button.
The currently selected menu item is displayed in reverse
video.
Buttons used to change settings
Use the following buttons to change setup menu settings.
To change the settings of menu items
Proceed as follows to change the settings of menu items.
1
Use the PUSH SET knob to select the required item.
Example: Screen display when item 005 DISPLAY
SEL is selected
2
Press the PUSH SET knob or the SELECT function
button (F2).
This displays the setting screen for the menu item
selected in step 1.
Example: Setting screen display when item 005
DISPLAY INFORMATION SELECT is selected
3
Use the PUSH SET knob or the +/– function button
(F3 or F4) to change the setting.
Turning the PUSH SET knob while holding down the
SHIFT button increases the increment of adjustment.
4
To change other settings, press the PUSH SET knob or
the RETURN function button (F1) to return to the
previous screen, then repeat steps 1 to 3.
5
When you have completed the settings, press the
SAVE function button (F5).
The message “NOW SAVING...” appears on the video
monitor screen, while the new settings are saved in
memory. When the save operation is completed, the
video monitor screen returns to its normal display.
• If you power off the unit before a save operation is
completed, settings may be lost. Wait until the save is
completed before powering off the unit.
• If, instead of pressing the SAVE function button (F5),
you press the MENU button, the new settings are not
saved. The message “ABORT !” appears on the video
monitor screen for about 0.5 seconds, and the system
exits the menus. To change more than one setting, be
Menu control
buttons
Functions
MENU button Displays and hides the menu.
PUSH SET knob • When turned clockwise or
counterclockwise, moves the reverse
video to select the item to change.
• When turned clockwise or
counterclockwise, changes a menu
item setting.
• When pressed, answers “Yes” to a
question.
Function buttons
F1 to F6
(The function to
be displayed
varies depending
on the situation.)
RETURN: Goes up one level.
SELECT: Selects an item.
UP: Skips back 100 or 50 items in the
list of menu items.
DOWN: Skips forward 100 or 50 items in
the list of menu items.
SAVE: Saves a new setting to memory.
EXIT: Exits the current menu.
–: Changes a setting.
+: Changes a setting.
RESET button • Returns the current setting to the
factory default.
• Answers “No” to a question.
Group name for the currently selected item
Currently selected item
Notes
Current setting
Current setting
91
Setup Menu
Chapter 7 Menus
sure to press the SAVE function button (F5) after
making the settings.
To return menu settings to their factory
default settings
After changing menu settings, use the following procedure
to return the settings to their factory default settings
(setting initialization).
To return a particular setting to its factory default
setting
On the screen that selects the setting of that item, press the
RESET button.
For example, proceed as follows to return the 005
DISPLAY INFORMATION SELECT item to its default
setting. This assumes that the setting has been changed
from the factory default “time data & status” in step 3 of
the procedure in “To change the settings of menu items”
(page 90).
1
Press the RESET button.
“time data & status” (factory default setting) is
selected.
2
Press the SAVE function button (F5).
The setting returned to its factory default is saved in
memory as the current setting.
To return all settings to their factory default
settings
1
Press the MENU button to display the setup menu.
2
Press the RESET button.
The message “INITIALIZE ALL ITEMS TO
FACTORY PRESET VALUES?” appears, to confirm
whether you wish to return all settings to their factory
default settings.
3
Press the SAVE function button (F5).
The message “NOW SAVING...” appears on the video
monitor screen, while the settings of all items are
returned to their factory default settings. These factory
default settings are saved in memory.
If you power off the unit while settings are being
saved, settings may not be correctly returned to their
factory default settings. Wait until the save operation
is completed before powering off the unit.
To abandon the resetting operation
Instead of pressing the SAVE function button (F5),
press the RESET button.
The display returns to the top level of the setup menu,
leaving the settings unchanged.
Menu bank operations (menu items B01 to B13)
You can save menu settings in a menu bank. Menu settings
saved in a menu bank can be recalled and used when
needed.
At startup and after menu ABORT (MENU button)
Current settings Current bank
Menu bank 1
Menu bank 2
Menu bank 3
Save menu and exit (F5 SAVE button)
Recall (B01)
Save (B11)
Recall (B02)
Save (B12)
Recall (B03)
Save (B13)
92 Setup Menu
Chapter 7 Menus
To save the current settings in a menu bank
1
Select a menu item from B11 “SAVE SETUP BANK-
1” to B13 “SAVE SETUP BANK-3” using the PUSH
SET knob.
2
Press either the PUSH SET knob or the SELECT
function (F2) button.
3
Change the setting to “on” using either the PUSH SET
knob or + function (F4) button.
4
Press the SAVE function (F5) button.
“NOW SAVING…” is displayed, and the current
settings are saved in the selected menu bank.
Settings are not saved in the current bank when saving to a
menu bank. To save changed settings in both a menu bank
and the current bank, press the SAVE function (F5) button
again after saving the settings in a menu bank to save the
settings in the current bank.
To recall settings saved in a menu bank
1
Select a menu item from B01 “RECALL SETUP
BANK-1” to B03 “RECALL SETUP BANK-3” using
the PUSH SET knob.
2
Press either the PUSH SET knob or the SELECT
function (F2) button.
3
Change the setting to “on” using either the PUSH SET
knob or + function (F4) button.
4
Press the LOAD function (F5) button.
“NOW LOADING...” is displayed, and the settings
saved in the selected menu bank are loaded as the
current settings.
5
Press the SAVE function (F5) button.
“NOW SAVING...” is displayed, and the current
settings are saved in the current bank. When saving is
finished, the display returns to the operating screen.
Items in the extended menu
The following tables show the items in the extended menu.
• The values in the “Settings” column are the values that
appear on settings screens. The values in brackets [ ] are
the value shown on menu screens (when they differ from
the values shown on settings screens).
• The underlined values are the factory defaults.
Note
Menu items in the 100s, relating to the control panels
Item number Item name Settings
101 SELECTION FOR SEARCH DIAL
ENABLE
Select how the unit enters the jog, shuttle, or variable mode.
dial direct [dial]: Press the SHTL/JOG or VAR/JOG button or, except
during recording/editing, turn the jog dial or shuttle dial.
via search key [key]: Press the SHTL/JOG or VAR/JOG button.
105 REFERENCE SYSTEM ALARM Select whether to display a warning when the reference video signal is
not being supplied, or when it differs from this unit’s system frequency.
off: No warning.
on: Flash the STOP button as a warning.
108 AUTO EE SELECT If PB/EE is set to “EE” on the P5 OTHER page in the function menu, this
selects the operation modes in which video/audio signal are handled as
EE signals.
stop/f.fwd/f.rev [S/F/R]: In stop, forward direction high-speed search,
and reverse direction high-speed search modes.
stop: In stop mode.
109 FORCED EE WHEN DISC UNLOAD During disc loading/unloading and when no disc is inserted, select
whether to control the output signal PB/EE setting.
on: Do not control (the signal is always an EE signal).
off: Control.
114 AUDIO MONITOR OUTPUT LEVEL Select whether to control the level of the audio signal output from the
AUDIO MONITOR OUTPUT R, L connectors with the LEVEL adjustment
knob for the PHONES jack.
variable [var]: Control.
fixed: Do not control.
93
Setup Menu
Chapter 7 Menus
121 FRAME PB MODE Select the variable-speed playback field/frame mode.
auto: Field playback
frame: Frame playback.
Compared to field playback, frame playback gives more detail during
playback of still pictures.
130 DISPLAY DIMMER CONTROL Set the brightness of the display on the LCD.
10%, 25%, 50%, 75%, 100%
131 AUDIO VOLUME Select whether each of the CH-1/ALL CH, CH-2 to CH-4 adjustment
knobs on the control panel is enabled to control the audio recording level
and playback level on each channel or the CH-1/ALL CH adjustment
knob alone functions as a master control to control the audio level on all
channels together.
each: Each of the CH-1/ALL CH, CH-2 to CH-4 adjustment knobs is
enabled to control each channel.
all: The CH-1/ALL CH adjustment knob alone functions as a master
control.
When “all” is selected, the ALL CH indicator under the CH-1/ALL CH
adjustment knob lights up.
142 REPEAT MODE Set whether to set repeat playback mode.
off: Do not set repeat playback mode.
play & VAR fwd [P&VAR]: Perform repeat playback during normal
playback and 0 to +1 times normal speed variable playback in the
forward direction. To select repeat playback in this mode from a
device connected to the REMOTE (9P) connector, send the
“REPEAT PLAY” command or the “REPEAT VAR FWD” command.
force: Perform repeat playback during normal playback and 0 to +1 times
normal speed variable playback in the forward direction. To select
repeat playback in this mode from a device connected to the
REMOTE (9P) connector, send the “PLAY” command or the “VAR
FWD” command.
When “play & VAR fwd” or “force” is selected, the icon indicating repeat
playback mode appears on the basic operation screen. When “on” is
selected also in setup menu item 154, the icon indicating both single clip
playback mode and repeat playback mode appears on the basic
operation screen.
143 INDEX PICTURE POSITION Select the frame of the clip to use as the thumbnail image (index picture)
when recording.
0sec to 10sec: Can be set in the range from 0 seconds (first frame of the
clip) to10 seconds, in units of 1 second.
145 MODE KEY ENABLE DURING
RECORDING
Set the mode buttons enabled during recording.
all enable [ena]: All buttons are enabled.
stop: Only the STOP button is enabled.
150 REC MODE Select the recording mode.
normal [norml]: Normal recording mode
disc exchange cache [D.EXC]: Disc Exchange Cache mode
151 GUI OPERATION Set whether to disable switching to the clip list screens.
enable [ena]: Enabled
via stop [stop]: Disabled (executable from stop mode only)
153 FIND MODE Specify the frame to cue up when the PREV or NEXT button is pressed.
clip: The first frame of the clip
clip & rec start mark [R.ST]: The frame where a Rec Start essence
mark is set (if no essence mark is set, the first frame of the clip)
Menu items in the 100s, relating to the control panels
Item number Item name Settings
94 Setup Menu
Chapter 7 Menus
154 SINGLE CLIP PLAY MODE Put the unit into single clip playback mode, or exit from single clip
playback mode.
off: Exits from single clip playback mode. (Puts the unit into continuous
playback mode.)
on: Puts the unit into single clip playback mode.
When “on” is selected, the icon indicating single clip playback mode
appears on the basic operation screen. When “play & VAR fwd” or “force”
is selected also in setup menu item 142, the icon indicating both single
clip playback mode and repeat playback mode appears on the basic
operation screen.
161 HDMI OUT SELECT Specify which signal to output from the HDMI OUT connector: the same
signal as the SDI connector output, or the same signal as the SDI
connector output and thumbnails view signal by automatically switching
between them.
auto: Output the same signal as the SDI connector output and
thumbnails view signal by automatically switching between them.
SDI [sdi]: Output the same signal as the SDI connector output.
163 NEXT/PREV Set the operation when the NEXT button and PREV button are pressed.
enable [ena]: Jump to the next/previous clip.
F.FWD/F.REV [ff/fr]: Fast forward search when the NEXT button is
pressed, and fast reverse search when the PREV button is pressed.
Menu items in the 200s, relating to the remote control interface
Item number Item name Settings
201 PARA RUN Selects whether to synchronize operation of two or more PDW-HD1550
units.
disable [dis]: No synchronized operation
enable [ena]: Use synchronized operation
Notes
• If you are controlling from a VTR, select “enable” on all of the
PDW-HD1550 units.
• If you controlling from the RM-280 or another remote control device,
select “disable” on one of the PDW-HD1550 units and select “enable”
on all of the other PDW-HD1550 units.
214 REMOTE INTERFACE When the remote control switch is set to REMOTE, select the device
from which to remote-control this unit.
9PIN: Device connected to the REMOTE (9P) connector.
SDI: Device connected to the SD/HDSDI INPUT connector.
257 NETWORK ENABLE Select the remote control switch positions which enable network
connections.
network [net]: Only when the remote control switch is set to “NET”.
network & remote(9PIN) [n&9P]: When the remote control switch is
set to “NET”, or when the switch is set to “REMOTE” and setup
menu item 214 is set to “9PIN”.
259 NETWORK INTERFACE Select network protocols to be enabled.
FTP/CIFS [ftp]: Enable FTP and CIFS.
NET-RMT [nrmt]: Enable NetAPI and WebAPI.
ALL [all]: Enable all protocols.
Menu items in the 300s, relating to editing operations
Item number Item name Settings
320 DIGITAL AUDIO PB PROCESS ON
EDIT POINT
Specify the handling of audio at edit points.
cut: Carry out a cut (possibly resulting in audio discontinuities at the edit
point).
fade: Fade out and fade in.
Menu items in the 100s, relating to the control panels
Item number Item name Settings
95
Setup Menu
Chapter 7 Menus
Menu items in the 500s, relating to disc protection
Item number Item name Settings
501 STILL TIMER To protect the disc against shock and vibration, and to lengthen the life of
the laser diodes, the unit automatically enters standby state whenever a
specified time elapses in a disc stop mode (stop mode or the still picture
mode of search mode). This allows you to set the time after which the unit
exits the disc stop mode and enters standby state.
0.5 sec [0.5 s]... 8 min [8 m]... 30 min [30 m]: Can be set in the range
from 0.5 seconds to 30 minutes.
off: Do not put into standby state.
Menu items in the 600s, relating to the timecode and metadata
Item number Item name Settings
601 VITC POSITION
SEL-1 a) In 59.94i/59.94P/
29.97P mode
Select the line into which to insert VITC signals (SD output)
12H to 16H to 20H: Any line from line 12 through line 20.
Notes
• You can insert VITC signals in two places. To insert in two places, set
both item 601 and item 602.
• In 59.94i/59.94P/29.97P mode (J), output of wide picture information is
given priority if OUTPUT in setup menu item 731 is set to “auto” and the
VITC insertion line is set to line 16.
• In 59.94i/59.94P/29.97P mode (UC), output of wide picture information
is given priority if OUTPUT in setup menu item 731 is set to “auto” and
the VITC insertion line is set to line 20.
In 50i/50P/25P
mode
Select the line into which to insert VITC signals (SD output)
9H to 19H to 22H: Any line from line 9 through line 22.
Note
You can insert VITC signals in two places. To insert in two places, set
both item 601 and item 602.
602 VITC POSITION
SEL-2 a) In 59.94i/59.94P/
29.97P mode
Select the line into which to insert VITC signals (SD output)
12H to 18H to 20H: Any line from line 12 through line 20.
Notes
• You can insert VITC signals in two places. To insert in two places, set
both item 601 and item 602.
• In 59.94i/59.94P/29.97P mode (J), output of wide picture information is
given priority if OUTPUT in setup menu item 731 is set to “auto” and the
VITC insertion line is set to line 16.
• In 59.94i/59.94P/29.97P mode (UC), output of wide picture information
is given priority if OUTPUT in setup menu item 731 is set to “auto” and
the VITC insertion line is set to line 20.
In 50i/50P/25P
mode
Select the line into which to insert VITC signals (SD output)
9H to 21H to 22H: Any line from line 9 through line 22.
Note
You can insert VITC signals in two places. To insert in two places, set
both item 601 and item 602.
605 TCG REGEN MODE Select the signal to be regenerated when the timecode generator is in
regeneration mode.
TC&UB: Both the timecode and user bits are regenerated.
TC: Only the timecode is regenerated.
UB: Only the user bits are regenerated.
96 Setup Menu
Chapter 7 Menus
607 U-BIT BINARY GROUP FLAG Select the user bits to be used in the timecode generated by the
timecode generator.
000:not specified [000]: Character set not specified.
001:iso character [001]: 8-bit characters compliant with ISO 646 and
ISO 2022.
010:unassigned-1 [010]: Undefined.
011:unassigned-2 [011]: Undefined.
100:unassigned-3 [100]: Undefined.
101:page / line [101]: SMPTE ST 262 page/line multiplex system.
110:unassigned-4 [110]: Undefined.
111:unassigned-5 [111]: Undefined.
611 TC OUTPUT PHASE IN EE MODE Select the timecode output mode for output from the TIME CODE OUT
connector in EE mode.
through [thru]: Output the timecode input to the TIME CODE IN
connector as is.
video input phase [v-in]: Output the timecode with the same phase as
the input video signal phase.
video output phase [v-out]: Output the timecode with the same phase
as the output video signal phase.
618 UPCONV EMBEDDED VITC a) Select the source of the VITC embedded in the output HDSDI signal
when up-converting during playback of an SD clip.
VITC: Select the VITC of the SD clip.
LTC: Select the LTC of the SD clip.
619 VITC a) Select whether to record the VITC generated by the internal timecode
generator during IMX recording.
off: Do not record the internally generated VITC.
on: Record the internally generated VITC.
Note
Even if this item is set to “off”, VITC is recorded if the input video signal
contains VITC and the VITC line is set to “throu” in menu item 723.
651 UMID SDI OUTPUT Select whether to output UMID in the VANC of the SDI output.
off: Do not output.
on: Output.
See “Using UMID Data” (page 126) for more information about UMID.
652 UMID SD VANC LINE a) Select the line in which UMID is output when menu item 651 is set to
“on”.
12H, 13H, 15H, 16H, 17H, 18H, 19H (59.94i/59.94P/29.97P mode)
9H, 10H, 12H, 13H, 14H, 15H, 16H, 17H, 18H (50i/50P/25P mode)
See “Using UMID Data” (page 126) for more information about UMID.
653 UMID HD VANC LINE Select the line in which UMID is output when menu item 651 is set to
“on”.
9H to 17H to 20H (59.94i, 50i, 29.97P, 25P, 23.98P mode)
9H to 17H to 25H (59.94P, 50P mode)
See “Using UMID Data” (page 126) for more information about UMID.
657 ESSENCE MARK SDI OUTPUT Select whether to output essence marks in the SDI output VANC.
off: Do not output.
on: Output.
660 ESSENCE MARK SD VANC LINE a) Select the line to which to output essence marks when menu item 657 is
set to “on”.
12H, 13H, 15H, 16H, 17H, 18H, 19H (59.94i/59.94P/29.97P mode)
9H, 10H, 12H, 13H, 14H, 15H, 16H, 17H, 18H (50i/50P/25P mode)
665 ESSENCE MARK HD VANC LINE Select the line to which to output essence marks when menu item 657 is
set to “on”.
9H to 17H to 20H (59.94i, 50i, 29.97P, 25P, 23.98P mode)
9H to 17H to 25H (59.94P, 50P mode)
Menu items in the 600s, relating to the timecode and metadata
Item number Item name Settings
97
Setup Menu
Chapter 7 Menus
a) Not displayed when the unit is in 23.98P mode.
666 METADATA ITEM OUT Specify whether to include the information from recorded VANC packets
in data items in the DATA ITEM section of MXF files.
off: Do not include VANC packet information in DATA ITEM.
on: Include VANC packet information in DATA ITEM.
668 USER META DATA OUTPUT IN
MXF
Select whether to output user metadata to MXF files.
off: Do not output.
on: Output.
Menu items in the 700s, relating to video control
Item number Item name Settings
703 BLANK LINE SELECT a) Switch blanking of the video output signal on or off for individual lines in
the vertical blanking interval.
Sub-item The Y/C signal and odd/even fields are blanked simultaneously.
ALL LINE - - -: Specify the blanking for each line separately.
blank [blnk]: Regardless of the setting of other sub-items, blank all lines
which can be specified in this menu item.
throu [thru]: Regardless of the setting of other sub-items, switch off
blanking for all lines which can be specified in this menu item.
In 59.94i/59.94P/
29.97P mode
(UC)
LINE 12 ...
LINE 19
Specify blanking for lines 12 to 19.
blank [blnk]: Carry out blanking.
throu [thru]: Switch off blanking.
LINE 20 Specify blanking for line 20.
blank [blnk]: Carry out blanking.
half: Carry out half-blanking.
throu [thru]: Switch off blanking.
In 59.94i/59.94P/
29.97P mode (J)
LINE 12 …
LINE 20
Specify blanking for lines 12 to 20.
blank [blnk]: Carry out blanking.
throu [thru]: Switch off blanking.
LINE 21 Specify blanking for line 21.
blank [blnk]: Carry out blanking.
half: Carry out half-blanking.
throu [thru]: Switch off blanking.
In 50i/50P/25P
mode
LINE 9, 322 ...
LINE 22, 335
Specify blanking for lines 9, 322 to 22, 335.
blank [blnk]: Carry out blanking.
throu [thru]: Switch off blanking.
LINE 23 Specify blanking for line 23.
half: Carry out half-blanking.
throu [thru]: Switch off blanking.
705 EDGE SUBCARRIER REDUCER
MODE a) Select whether to enable the edge subcarrier reducer (ESR).
on: Enable ESR.
off: Do not enable ESR.
707 FORCED VERTICAL
INTERPOLATION OFF
The “Y-add” function is normally switched on automatically during jog or
variable-speed playback. This item selects whether to force the “Y-add”
function off.
auto: Automatically switch the “Y-add” function on.
forced YADD off [off]: Force the “Y-add” function off.
The “Y-add” function is a circuit operation to interpolate the video signal
vertically during jog or variable-speed playback for the purpose of
reducing the vertical movement of the playback picture.
Menu items in the 600s, relating to the timecode and metadata
Item number Item name Settings
98 Setup Menu
Chapter 7 Menus
710 INTERNAL VIDEO SIGNAL
GENERATOR
Select the test signal to be output from the internal test signal generator.
When INT SG on page P1 INPUT of the function menu is set to “ON”,
the internal test signal generator operates to output the selected test
signal. This signal can also be recorded.
Off [OFF]: Do not output test signal.
75% Color Bars [CB75]: 75% color bar signal
100% Color Bars [CB100]: 100% color bar signal
Multi Burst [MLTBS]: Multi-burst signal
10 steps [10STP]: 10-step signal
Pulse and Bar [PLSBR]: Pulse and bar signal
Ramp [RAMP]: Ramp signal
Black [BLACK]: Black signal
ARIB Color Bars [ARBCB]: ARIB color bar signal (modify width: 100%)
Note
“ARIB Color Bars” cannot be specified when SD recording is selected. If
“ARIB Color Bars” is selected, the selection is changed to “75% Color
Bars” ([CB75]).
713 VIDEO SETUP REFERENCE b) Set the video setup amount to be added to the composite output signal.
Sub-item
OUTPUT LEVEL In 59.94i/59.94P/
29.97P mode
(UC)
Add the setup level selected by this item to the output signal.
0.0%, 7.5%
In 59.94i/59.94P/
29.97P mode (J)
Add the setup level selected by this item to the output signal.
0.0%, 7.5%
715 VIDEO GAIN CONTROL a) Adjust the video output level of SD video signals output from the SDSDI
OUTPUT, COMPOSITE OUTPUT, or HDMI OUT connectors.
–2048 to 0 to 848
716 CHROMA GAIN CONTROL a) Adjust the chroma output level of SD video signals output from the
SDSDI OUTPUT, COMPOSITE OUTPUT, or HDMI OUT connectors.
–2048 to 0 to 848
717 CHROMA PHASE CONTROL a) Adjust the chroma phase of SD video signals output from the SDSDI
OUTPUT, COMPOSITE OUTPUT, or HDMI OUT connectors.
–128 to 0 to 127
718 SETUP LEVEL (59.94i/59.94P/
29.97P mode)/BLACK LEVEL (50i/
50P/25P mode) a)
Adjust the setup level (black level) of SD video signals output from the
SDSDI OUTPUT, COMPOSITE OUTPUT, or HDMI OUT connectors.
–272 to 0 to 272
719 SYSTEM PHASE SYNC a) Adjust the sync phase of SD video signals output from the SDSDI
OUTPUT, COMPOSITE OUTPUT, or HDMI OUT connectors.
–128 to 0 to 127
720 SYSTEM PHASE SC a) Adjust the subcarrier phase of SD video signals output from the SDSDI
OUTPUT, COMPOSITE OUTPUT, or HDMI OUT connectors.
0 to 511
723 INPUT VIDEO BLANK a) Switch blanking on or off for lines in the vertical blanking interval of input
video signals. Lines can be specified individually. Y/C signals and odd/
even fields are blanked simultaneously.
Blanking in recorded signals is carried out according to these settings.
Sub-item
1 ALL LINE ---: Specify the blanking for each line separately
blank [blnk]: Regardless of the settings of other sub-items, blank all
lines which can be specified in this menu item.
throu [thru]: Regardless of the settings of other sub-items, switch
blanking off for all lines which can be specified in this menu item.
2
|
10
LINE12-
LINE20
In 59.94i/59.94P/
29.97P mode
Specify blanking for lines 12 to 20.
blank [blnk]: Switch blanking on.
throu [thru]: Switch blanking off.
2
|
15
LINE9, 322-
LINE22, 335
In 50i/50P/25P
mode
Specify blanking for lines 9, 322 to 22, 335.
blank [blnk]: Switch blanking on.
throu [thru]: Switch blanking off.
Menu items in the 700s, relating to video control
Item number Item name Settings
99
Setup Menu
Chapter 7 Menus
a) Not displayed when the unit is in 23.98P mode.
b) Not displayed when the unit is in 50i/50P/25P/23.98P mode.
726 H BLANKING WIDTH a) Select the horizontal blanking width of the output analog video signal.
narrow [narow]: Digital blanking (narrow)
wide: Analog blanking (wide)
When “wide” is selected, the horizontal blanking width complies with
SMPTE ST 170, and normally the blanking is widened and the image
becomes narrower. It is recommended to select “narrow” at the editing
stage, then later, for broadcast transmission to select “wide”, to output a
signal conforming to the standard. Note, however, that “narrow” has to
be always selected for SDI signals.
728 OUTPUT SCH PHASE a) Set the subcarrier H phase.
–512 to 0 to 511
731 WIDE MODE a) Specify whether to record and play back with the addition of wide picture
information.
Sub-item
1 INPUT Select whether to save wide picture information when recording.
auto: Automatically save wide picture information when it is detected in
the selected input video signal.
on: Always save wide picture information.
off: Never save wide picture information
2 OUTPUT Select whether to add wide picture information to the signal output when
down-converter output is set to squeeze mode.
through [thru]: Do not add.
auto: Add.
Notes
• To add wide picture information to the output signal, another setting is
required in addition to this item. In setup menu item 703, set line 16
(59.94i/59.94P/29.97P mode (J)), line 20 (59.94i/59.94P/29.97P mode
(UC)), or line 23 (50i/25P mode) to “throu”.
• In 59.94i/59.94P/29.97P mode (J), output of wide picture information is
given priority if the VITC insertion line is set to line 16 in setup menu
item 601 or 602.
• In 59.94i/59.94P/29.97P mode (UC), output of wide picture information
is given priority if the VITC insertion line is set to line 20 in setup menu
item 601 or 602.
740 MASTER LEVEL (HD) Adjust the high-definition video signal output from the HDSDI OUTPUT
or HDMI OUT connectors. This adjusts the Y, PB, and PR levels
simultaneously.
–2048 to 0 to 846
741 Y LEVEL (HD) Adjust the Y level of the high-definition video signal output from the
HDSDI OUTPUT or HDMI OUT connectors.
–2048 to 0 to 846
742 PB LEVEL (HD) Adjust the PB level of the high-definition video signal output from the
HDSDI OUTPUT or HDMI OUT connectors.
–2048 to 0 to 846
743 PR LEVEL (HD) Adjust the PR level of the high-definition video signal output from the
HDSDI OUTPUT or HDMI OUT connectors.
–2048 to 0 to 846
745 SETUP LEVEL (HD) Adjust the setup level of the high-definition video signal output from the
HDSDI OUTPUT or HDMI OUT connectors.
–272 to 0 to 272
746 SYNC PHASE (HD) Control the H sync phase of the high-definition video signal output from
the HDSDI OUTPUT or HDMI OUT connectors.
–128 to 0 to 127
747 FINE (HD) Fine control the H sync phase of the high-definition video signal output
from the HDSDI OUTPUT or HDMI OUT connectors.
0 to 1023
Menu items in the 700s, relating to video control
Item number Item name Settings
100 Setup Menu
Chapter 7 Menus
Menu items in the 800s, relating to audio control
Item number Item name Settings
802 DIGITAL AUDIO MUTING IN
SHUTTLE MODE
Set the audio muting conditions during shuttle playback.
off: Not muted.
on: Muted.
807 AUDIO OUTPUT PHASE Set the output timing of digital audio playback signals (HDSDI, SDI only)
as a hexadecimal value, with 80 as a reference position. Output timing is
earlier for values smaller than 80 and later for values greater than 80. (80
with 128 samples = approx. 2.7 ms, 80 with 1 sample = approx. 20 μs)
0 to 80 to FF: Values can be set in this range.
808 INTERNAL AUDIO SIGNAL
GENERATOR
Select the operation of the internal audio test signal generator.
off: Do not output test signal.
silence [silnc]: Silent signal
1kHz sine [1kHz]: 1 kHz, –20 dB FS sine wave signal
When you set the INT SG item on page P1 INPUT of the function menu
to “ON”, the internal signal generator operates and outputs simultaneous
test signals to channels 1 to 8 (see page 40).
815 AUDIO SAMPLING RATE
CONVERTER
Select the mode of operation of the sampling rate converter for AES/
EBU input to channels 1 to 4.
off: Do not operate.
on: Operate.
823 NON-AUDIO FLAG PB Control non-audio flags in digital audio output.
Sub-item
1 CH1/CH2 During playback (except in EE mode), set non-audio flags in digital audio
output to the following states.
on: Set to on (data is non-audio.)
auto: Set as follows.
• When data is read from a disc and confirmed: Follow the state on
the disc.
• When data from a disc is not confirmed: Maintain current state.
2 CH3/CH4
3 CH5/CH6
4 CH7/CH8
824 ANALOG LINE OUTPUT SELECT Select the analog audio signals (tracks 1 to 8) to be assigned to audio
output channels 1 and 2.
tr1/2: Tracks 1 and 2 assigned to audio output channels 1 and 2.
tr3/4: Tracks 3 and 4 assigned to audio output channels 1 and 2.
tr5/6: Tracks 5 and 6 assigned to audio output channels 1 and 2.
tr7/8: Tracks 7 and 8 assigned to audio output channels 1 and 2.
827 AES/EBU AUDIO OUTPUT SELECT Select the audio signals to assign to AES/EBU audio output channels.
Sub-item
1 CH1/CH2 tr1/2: Tracks 1 and 2 assigned to audio output channels 1 and 2.
tr3/4: Tracks 3 and 4 assigned to audio output channels 1 and 2.
tr5/6: Tracks 5 and 6 assigned to audio output channels 1 and 2.
tr7/8: Tracks 7 and 8 assigned to audio output channels 1 and 2.
2 CH3/CH4 tr1/2: Tracks 1 and 2 assigned to audio output channels 3 and 4.
tr3/4: Tracks 3 and 4 assigned to audio output channels 3 and 4.
tr5/6: Tracks 5 and 6 assigned to audio output channels 3 and 4.
tr7/8: Tracks 7 and 8 assigned to audio output channels 3 and 4.
828 SDI AUDIO OUTPUT SELECT Select the audio signals to assign to SDI audio output channels.
Sub-item
1 CH1/CH2 tr1/2: Tracks 1 and 2 assigned to audio output channels 1 and 2.
tr3/4: Tracks 3 and 4 assigned to audio output channels 1 and 2.
tr5/6: Tracks 5 and 6 assigned to audio output channels 1 and 2.
tr7/8: Tracks 7 and 8 assigned to audio output channels 1 and 2.
2 CH3/CH4 tr1/2: Tracks 1 and 2 assigned to audio output channels 3 and 4.
tr3/4: Tracks 3 and 4 assigned to audio output channels 3 and 4.
tr5/6: Tracks 5 and 6 assigned to audio output channels 3 and 4.
tr7/8: Tracks 7 and 8 assigned to audio output channels 3 and 4.
101
Setup Menu
Chapter 7 Menus
834 AUDIO INPUT LEVEL Select the analog audio input source.
Sub-item
1 CH1 line: Line input
mic: Microphone input
2 CH2 line: Line input
mic: Microphone input
839 AUDIO AGC/LIMITER MODE For automatic input level adjustments performed on the analog audio
signals recorded on channels 1 and 2, select whether to perform the
adjustments in stereo mode or independently for channels 1 and 2.
mono: Perform automatic adjustments independently for channels 1 and
2.
stereo: Perform automatic adjustments in stereo mode.
840 AUDIO AGC SELECT Set the AGC saturation level.
off: AGC does not operate.
–6dB, –9dB, –12dB, –15dB, –17dB: AGC operates when the
VARIABLE switch is set to PRESET.
Note
This setting is enabled only for channels that have “mic” (microphone
input) selected in setup menu item 834. For channels that have “line”
(line input) selected, this function is “off” regardless of the item setting.
841 AUDIO LIMITER SELECT Select the limiter saturation level, for limiting large input signals, for use
in manual adjustment of audio input levels.
off: The limiter does not operate.
–6dB, –9dB, –12dB, –15dB, –17dB: The limiter operates when the
VARIABLE switch is set to REC or PB.
Note
This setting is enabled only for channels that have “mic” (microphone
input) selected in setup menu item 834. For channels that have “line”
(line input) selected, this function is “off” regardless of the item setting.
Menu items in the 900s, relating to digital processing
Item number Item name Settings
920 SD-SDI H-ANC CONTROL a) Select whether to add information to the SDI output.
Sub-item
1 AUDIO 5CH-8CH off: Do not add digital audio data channels 5 to 8.
on: Add digital audio data channels 5 to 8.
2 RP188 ATC off: Do not add RP188 timecode data.
on: Add RP188 timecode data.
925 HDMI OUTPUT SELECT a) Select the resolution of the video output from the HDMI OUT connector.
1080i, 480i, 480P (59.94i, 29.97P mode)
1080i, 576i, 576P (50i, 25P mode)
720P
, 480i, 480P (59.94P mode)
720P, 576i, 576P (50P mode)
930 DOWN CONVERTER MODE a) Select the down-converter mode.
EDGE CROP [CROP]: Select the edge crop mode.
LETTER BOX [L-BOX]: Select the letter box mode.
SQUEEZE [SQUEZ]: Select the squeeze mode.
931 DOWN CONVERTER LETTER BOX
MODE a) Select the aspect ratio of the down-converter output when menu item
930 is set to “LETTER BOX”.
16:9: Set the aspect ratio of the HD-SD converter output to 16:9.
14:9: Set the aspect ratio of the HD-SD converter output to 14:9.
13:9: Set the aspect ratio of the HD-SD converter output to 13:9.
932 H CROP POSITION (DC) a) Adjust the H-crop (the horizontal position when cropping in the edge crop
mode) of the down-converter output when menu item 930 is set to
“EDGE CROP”.
–120 to 0 to 120
Menu items in the 800s, relating to audio control
Item number Item name Settings
102 Setup Menu
Chapter 7 Menus
934 CROSS COLOR (DC) a) Adjust the down-converter cross color.
0 to 8 to 15
935 DETAIL GAIN (DC) a) Adjust the down-converter image enhancer. Adjust the sharpness of
edge enhancement.
00 (HEX) to 7F (HEX)
936 LIMITER (DC) a) Adjust the down-converter image enhancer. Set the maximum detail level
added to emphasize the original signal.
00 (HEX) to 20 (HEX) to 3F (HEX)
937 CRISP (DC) a) Adjust the down-converter image enhancer. Set the threshold amplitude
for emphasis (signals of amplitude lower than the threshold are not
emphasized).
00 (HEX) to 0F (HEX)
938 LEVEL DEPEND THRESHOLD
(DC) a) Adjust the down-converter image enhancer. Set the luminance range for
edge enhancement.
00 (HEX) to 08 (HEX) to 0F (HEX)
939 H DETAIL FREQUENCY (DC) a) Adjust the down-converter image enhancer. Set the central frequency for
edge enhancement.
2.6MHz, 3.4MHz, 3.9MHz, 4.6MHz
940 H/V RATIO (DC) a) Adjust the down-converter image enhancer. Set the horizontal/vertical
ratio for edge enhancement.
00 (HEX) to 03 (HEX) to 07 (HEX)
942 V FILTER SELECT (DC) a), b) Set the vertical interpolation filter coefficient for down-converter output (in
1080 mode only).
If the setting value is large, the vertical resolution is high.
01 (HEX) to 03 (HEX)
943 CROSS COLOR CRISP (DC) a) Set the cross color crisp level for down-converter output.
00 (HEX) to 04 (HEX) to 0F (HEX)
944 D/C LEGALIZE (DC) a) For down-converter output, selects whether to suppress signals with
levels that are lower than the pedestal level.
off: Do not suppress signals lower than the pedestal level.
on: Suppress signals lower than the pedestal level.
950 UP CONVERTER MODE a) Select the up-converter mode.
EDGE CROP [CROP]: Select the edge crop mode.
LETTER BOX [L-BOX]: Select the letter box mode.
SQUEEZE [SQUEZ]: Select the squeeze mode.
951 H CROP POSITION (UC) a) Adjust the H-crop (the horizontal position when cropping in the edge crop
mode) of the up-converter output when menu item 950 is set to “EDGE
CROP”.
–120 to 0 to 120
952 LETTER BOX POSITION (UC) a) Adjust the vertical position where the picture is cut out for up-converter
output in letter box mode when menu item 950 is set to “LETTER BOX”.
–120 to 0 to 120
953 UP CONVERTER PROCESS a) Select the source picture to use in converting SD to HD.
FIELD: Use field pictures.
ADAPTIVE [ADAPT]: Frame or field is selected automatically.
954 DETAIL GAIN (UC) a) Adjust the up-converter image enhancer. Adjust the sharpness of edge
enhancement.
00 (HEX) to 40 (HEX) to 7F (HEX)
955 LIMITER (UC) a) Adjust the up-converter image enhancer. Set the maximum detail level
added to emphasize the original signal.
00 (HEX) to 20 (HEX) to 3F (HEX)
956 CRISP THRESHOLD (UC) a)
Adjust the up-converter image enhancer. Set the threshold amplitude for
emphasis (signals of amplitude lower than the threshold are not emphasized).
00 (HEX) to 08 (HEX) to 0F (HEX)
957 LEVEL DEPEND THRESHOLD
(UC) a) Adjust the up-converter image enhancer. Set the luminance range for
edge enhancement.
00 (HEX) to 08 (HEX) to 0F (HEX)
Menu items in the 900s, relating to digital processing
Item number Item name Settings
103
Setup Menu
Chapter 7 Menus
a) Not displayed when the unit is in 23.98P mode.
b) Not displayed when the unit is in 59.94P/50P mode.
958 H DETAIL FREQUENCY (UC) a) Adjust the up-converter image enhancer. Set the center frequency and
frequency properties for edge enhancement.
3.2MHz: 3.2 MHz ±1.1 MHz
4.5MHz: 4.5 MHz ±1.4 MHz
5.0MHz: 5.0 MHz ±0.7 MHz
4.0MHz: 4.0 MHz ±2.0 MHz
959 H/V RATIO (UC) a) Adjust the up-converter image enhancer. Set the horizontal/vertical ratio
for edge enhancement.
00 (HEX) to 03 (HEX) to 07 (HEX)
965 IMAGE ENHANCER (INPUT UP
CONVERTER) a)
Set up the operation of the up-converter image enhancer for SD input,
separately from the settings for playback (menu items 950 to 959).
Sub-item pb: While SD signals are input, make the behavior of the image
enhancer of the up-converter follow the settings for playback (menu
items 950 to 959). (Settings for sub-items 2 to 11 under menu item
965 become invalid.)
input: While SD signals are input, make the behavior of the image
enhancer of the up-converter follow the settings for sub-items 2 to 11
under menu item 965 (separate settings during input of SD signals
from those during playback).
1 ENH SETTING
2 CONVERT Select the up-converter mode.
EDGE CROP [CROP]: Select the edge-crop mode.
LETTER BOX [L-BOX]: Select the letter box mode.
SQUEEZE [SQUEZ]: Select the squeeze mode.
3 H CROP P Adjust the H-crop (horizontal crop) position for up-converter output in
edge crop mode when sub-item CONVERT is set to “CROP”.
–120 to 0 to 120
4 L BOX P Adjust the vertical location of the position where the picture is cut out for
up-converter output in letter box mode when sub-item CONVERT is set
to “L-BOX”.
–120 to 0 to 120
5 CNV PROC Select the source picture to use in converting SD to HD.
FIELD: Use field pictures.
ADAPTIVE [ADAPT]: Frame or field is selected automatically.
6 DETAIL Adjust the up-converter image enhancer. Set the sharpness of edge
enhancement.
00 to 40 to 7F (hexadecimal value)
7 LIMITER Adjust the up-converter image enhancer. Set the maximum detail level
added to emphasize the original signal.
00 to 20 to 3F (hexadecimal value)
8 CRISP Adjust the up-converter image enhancer. Set the threshold amplitude at
which low amplitude signals are not emphasized.
00 to 08 to 0F (hexadecimal value)
9 DEPEND Adjust the up-converter image enhancer. Set the luminance range for
edge enhancement.
00 to 08 to 0F (hexadecimal value)
10 H DETL F Adjust the up-converter image enhancer. Set the center frequency and
frequency properties for edge enhancement.
3.2MHz: 3.2 MHz ±1.1 MHz
4.5MHz: 4.5 MHz ±1.4 MHz
5.0MHz: 5.0 MHz ±0.7 MHz
4.0MHz: 4.0 MHz ±2.0 MHz
11 HV RATIO Adjust the up-converter image enhancer. Set the horizontal/vertical ratio
for edge enhancement.
00 to 03 to 07 (hexadecimal value)
Menu items in the 900s, relating to digital processing
Item number Item name Settings
104 Maintenance Menu
Chapter 7 Menus
Maintenance Menu
Items in the maintenance menu
The following tables show the items in the maintenance
menu.
• The values in the “Setting” column are the values that
appear in settings screens. The values in brackets [ ] are
the value shown in menu screens (when they differ from
the values shown in settings screens).
• The underlined values are the factory defaults.
For details on menu items that do not appear in this
manual (M1: ADJUST, M2: SERVICE SUPPORT, parts of
M3: OTHERS, and M6: DRIVE), refer to the Service
Manual.
M3: OTHERS: Other setting items
Item Setting
M30: SOFTWARE VERSION Display of the software version of this unit.
M31: SERIAL NUMBER Display of the serial number and Media Access Control (MAC) address of this
unit.
M33: FILE I/F CONFIG
PROAV DISPLAY Select whether to display the PROAV directory.
disable [dis]: Disable display.
enable [ena]: Enable display.
FTP STYLE Select operation when the unit is accessed via FTP connection.
xdcam style [xdcam]: Operate in conformance with existing XDCAM device.
xds style [xds]: Allow multiple logins.
M36: HOURS METER RESET Reset the display of resettable items of the operating hours meter.
H11: OPE HOURS
H13: SEEK HOURS0
H14: SPDL HOURS
H15: LOAD COUNT
105
Maintenance Menu
Chapter 7 Menus
M37: AUDIO
CONFIG
M370: HEAD ROOM Select the audio reference level (headroom).
–20dB, –18dB, –16dB, –12dB, EBUL
Note
EBUL can be selected only when the system frequency is 50i/25P.
M371: DATA LEN Specify the audio channel configuration used during IMX recording.
16bit×8ch [16×8]: 8-channel configuration with 16-bit data width.
24bit×4ch [24×4]: 4-channel configuration with 24-bit data width.
M372: NON-AUDIO
INPUT
Select whether to handle digital audio signals as non-audio signals during
recording.
audio: Handle as linear PCM audio signals.
data: Handle as non-audio signals.
Sub-item
1 tr1/tr2
2 tr3/tr4
3 tr5/tr6
4 tr7/tr8
M373: IN LEVEL Set the upper limit for the signal level input to audio channels 1/3/5/7 or 2/4/6/8.
+4dB, 0dB, –3dB, –6dB, EBUL
Note
EBUL can be selected only when the system frequency is 50i/25P.
Sub-item
1ANALOG1
2ANALOG2
3ANALOG3
4ANALOG4
M374: ANALOG I/O Specify whether to output analog audio signals from the ANALOG AUDIO
OUTPUT 1 and 2 connectors or input analog audio signals as the ANALOG
AUDIO OUTPUT 3 and 4 connectors.
2ch [2ch]: Output from the ANALOG AUDIO OUTPUT 1 and 2 connectors.
4ch [4ch]: Input as the ANALOG AUDIO INPUT 3 and 4 connectors.
M377: OUT LEVEL Set the reference level for audio output signals.
+4dB, 0dB, –3dB, –6dB, EBUL
Note
EBUL can be selected only when the system frequency is 50i/25P.
M38: F-KEY CONFIG For details, refer to the Service Manual.
M380: HOME2 Assign function to the HOME2 page of the function menu.
M381: PAGE6 ASSIGN Assign menu item to the P6 page of the function menu.
M382: PAGE6 NAME Specify the name of the setup menu item assigned with M381: PAGE6 ASSIGN.
M3: OTHERS: Other setting items
Item Setting
106 Maintenance Menu
Chapter 7 Menus
M39: OTHER
CONFIG
M391: VITC REC Select whether to record the VITC in the input HDSDI signals in the LTC user bits
area.
disable [dis]: Do not record.
enable [ena]: Record.
Notes
• Recording of VITC is enabled only when this is set to “enable,” and F1: TCG is
set to “EXT” and F2: PRST/RGN is set to “TC” on the P4 TC page in the
function menu.
• When set to “enable,” the value in the user bits area is output for VITC during
playback. Note that the value of the user bits area is output for VITC even when
playing back clips recorded without using this function.
• This setting has no affect during SD format recording/playback.
M395: FRMT MEDIA Specify whether to disable the Format Media command of the Clip Menu.
disable [dis]: Disable the Format Media command.
enable [ena]: Enable the Format Media command.
M399: VERIFY USB Specify whether to perform verification when copying data to external storage.
off: Verification is not performed.
on: Verification is performed.
M39B: COPY TO USB Specify whether to prohibit copying to external storage.
disable [dis]: Disable copying.
enable [ena]: Enable copying.
M3B: VANC RX
PAR AM E T ER
M3B0: VANC RX
PACKET
For setting HD-SDI VANC data input parameters
Notes
• In 59.94i, 50i, 29.97P or 25P mode, selecting the line also selects the
corresponding line in the second field (for example, if line 9 is selected, line 572
is also selected for VANC packet reception).
• Menu item M3B0 enables recording of one VANC packet when the selected line
contains any packets whose DID/SDID matches the value set with this menu
item.
• Up to four packets are recorded per each line regardless of the DID and SDID
for the VANC set with menu item M3B1 or M3B2.
• It is not possible to set the same line with menu items M3B0, M3B1, and M3B2.
If the same line is specified, priority is given in the order of M3B0, M3B1, and
M3B2 (for example, if the same line is specified with M3B0 and M3B1, the
setting with M3B1 is ignored).
• When VANC data is output to HD-SDI playback signals, the number of the
output VANC line is the same as that of the input VANC line.
• When a UMID or essence mark line is selected with M3B1 or M3B2, UMID or
essence mark output takes priority. To disable UMID or essence mark output,
set setup menu item 651 or 657 to “off”.
Sub-item
1 CC Configure the VANC to be received.
MANUAL [MANU]: Receive the VANC according to the LINE, DID, and SDID
settings.
EIA-708 [708]: Receive EIA-708 Closed Caption.
2 LINE Selects the LINE for the VANC to be received.
OFF, 9LINE to 20LINE (59.94i/50i/29.97P/25P/23.98P mode)
OFF, 9LINE to 25LINE (59.94P/50P mode)
3 DID Specification of the DID of the VANC to receive
00h-FFh
4 SDID Specification of the SDID of the VANC to receive
00h-FFh
M3B1: LINE1 SEL Selects the LINE to be received for the HD-SDI VANC data.
OFF, 9LINE to 20LINE (59.94i/50i/29.97P/25P/23.98P mode)
OFF, 9LINE to 25LINE (59.94P/50P mode)
M3B2: LINE2 SEL Selects the LINE to be received for the HD-SDI VANC data.
OFF, 9LINE to 20LINE (59.94i/50i/29.97P/25P/23.98P mode)
OFF, 9LINE to 25LINE (59.94P/50P mode)
M3: OTHERS: Other setting items
Item Setting
107
Maintenance Menu
Chapter 7 Menus
M3D: DATE/TIME PRESET Specifies the year, month, day, time, and time zone.
M3E: USB MEMORY UTIL
M3E0: USB to ROM Download setup menu configuration data stored in USB memory to the unit.
M3E1: ROM to USB Save setup menu configuration data to USB memory.
M3E2: FORMAT USB
MEM
Format the USB memory connected to the USB connector on the front panel in
FAT32 format.
M3F: FACTORY SETUP For details, refer to the Service Manual.
M4: SETUP MAINTENANCE: Items relating to the setup menu
Item Setting
M40: EXTENDED MENU Select whether to display the extended menu.
DISABLE [dis]: Do not display.
ENABLE [ena]: Display.
M42: F-MENU BANK Select whether to save the function menu settings in a menu bank.
DISABLE [dis]: Do not save the function menu settings in a menu bank.
ENABLE [ena]: Save the function menu settings in a menu bank.
M48: AUTO RECALL Select whether to recall settings automatically from a menu bank when the
system is powered on, and if so which menu bank to recall from.
off: Do not recall settings from a menu bank.
from BANK1 [Bank1]: Recall settings from menu bank 1.
from BANK2 [Bank2]: Recall settings from menu bank 2.
from BANK3 [Bank3]: Recall settings from menu bank 3.
M49: RESET ALL SETUP Reset all the menu settings to the factory settings.
Push the SAVE function button (F5): Reset.
Push the MENU button: Return to the next highest menu level without resetting.
Notes
• The system frequency setting is also cleared. If you execute this item, reset the
system frequency (see page 34).
• Date and time settings are not cleared, but the time zone setting is cleared.
After executing this item, reset the time zone (see page 107).
M5: NETWORK: Items relating to network settings
Item Setting
M50: DHCP Set whether to assign an IP address automatically with the DHCP server.
DISABLE [dis]: Do not assign automatically.
ENABLE [ena]: Assign automatically.
M51: IP ADDRESS Set the IP address of this unit.
192.168.001.010
Notes
• IP address cannot be set when DHCP is set to “ENABLE”.
• To check the automatically acquired IP address of this unit, close the maintenance
menu and then open it again.
M52: SUBNET MASK Set the subnet mask.
255.255.255.000
Notes
• Subnet mask cannot be set when DHCP is set to “ENABLE”.
• To check the automatically acquired subnet mask, close the maintenance menu
and then open it again.
M3: OTHERS: Other setting items
Item Setting
108 Maintenance Menu
Chapter 7 Menus
a) A “jumbo” frame is a frame larger than the maximum 1514 bytes (not
including FCS) of the standard Ethernet frame. Jumbo frames make it
possible to deliver larger payloads per packet. Since fewer packets need to
be routed, packet processing overhead is lower and network throughput is
potentially improved. (Note that this item is enabled only when LINK
SPEED is set to “1Gbps FullDuplex”. For it to work, all other devices that
handle packets on the network must also support jumbo frames.)
Maintenance menu operations
This section describes the indications in the maintenance
menu and how to change the settings.
To display the maintenance menu
Holding down the PAGE/HOME button and the SHIFT
button, press the MENU button.
The maintenance menu appears on the video monitor
screen and the currently-set menu item is displayed in
reverse video.
Meanings of indications on the menu
screen To change a menu item setting
Carry out the following operations to change the setting.
For information about how to change network settings, see
“To change network settings” (page 109).
M53: DEFAULT GATEWAY Set the address of the default gateway.
000.000.000.000
Notes
• The address of the default gateway cannot be set when DHCP is set to “ENABLE”.
• To check the automatically acquired address of the default gateway, close the
maintenance menu and then open it again.
M54: LINK SPEED Set the communications speed and protocol.
AUTO [auto]: Sets automatically.
1Gbps FullDuplex [1G F]: 1 Gbps, full duplex
100Mbps FullDuplex [100 F]: 100 Mbps, full duplex
100Mbps HalfDuplex [100 H]: 100 Mbps, half duplex
10Mbps FullDuplex [10 F]: 10 Mbps, full duplex
10Mbps HalfDuplex [10 H]: 10 Mbps, half duplex
M56: JUMBO FRAME a) Set the size of jumbo frames.
9014, 4088, OFF(1514)
Note
This value does not include the 4 bytes of the FCS (Frame Check Sequence).
M5A: NetBIOS Specify whether to enable NetBIOS over TCP/IP.
off: Disable.
on: Enable.
M5F: RESET NET CONFIG Reset network settings to the factory defaults.
Push the SAVE function button (F5): Reset.
Push the MENU button: Return to the next highest menu level without executing the
reset.
M5: NETWORK: Items relating to network settings
Item Setting
On-screen indication Meaning
Right-pointing arrow
(c) at the right of a
menu item
Pressing the PUSH SET knob or
the b/OUT button switches to the
next lower menu level or to a
setting selection screen.
Left-pointing arrow (C)
at the left of a menu
item
Pressing the PUSH SET knob or
the B/IN button switches to the
previous (higher) menu level.
Character string at the
right of a menu item
Current setting of the menu item
When shown with a colon (:): the
current setting is the same as
the factory default setting.
When shown with a raised dot
(.): the current setting is
different from the factory
default setting.
An * (asterisk) in a
complete list of settings
Factory default setting
On-screen indication Meaning
109
Maintenance Menu
Chapter 7 Menus
1
Use the PUSH SET knob or the V/MARK1 and
v/MARK2 buttons to select the required item, then
press the PUSH SET knob or the SELECT function
button (F2).
The sub-items of the selected item appears.
2
Select a sub-item with the same operation as step 1,
and use the PUSH SET knob or the V/MARK1 and
v/MARK2 buttons to change the setting.
3
Press the PUSH SET knob or the SELECT function
button (F2) to confirm the setting change.
4
Press the SAVE function button (F5).
The message “NOW SAVING...” appears on the video
monitor screen, while the new settings are saved in
memory. When the saving operation is completed, the
video monitor screen returns to its normal indications.
To cancel changing a setting
Before pressing the SAVE function button (F5), press the
MENU button.
The menu disappears from the video monitor screen,
without saving the new setting.
To change network settings
To change network settings, carry out the procedure
described in “To display the maintenance menu”
(page 108) to display the NETWORK menu item, then
carry out the following operations.
For details on settings, consult your network
administrator.
Depending on the operating environment, unauthorized
third parties on the network may be able to access the
system.
We strongly recommend configuring all of the passwords
for security purposes.
For details about changing passwords, contact your Sony
dealer.
When the IP address is assigned automatically
Check that the network cable is connected to this unit
before carrying out the operation.
1
Set maintenance menu item M5: NETWORK
>M50: DHCP to “ENABLE”.
2
In the NETWORK menu, press the SAVE function
button (F5).
3
When the “NOW SAVING...” message vanishes,
power the unit off and then on again with the on/
standby button.
To check the assigned IP address
Select maintenance menu item M5: NETWORK
>M51: IP ADDRESS.
If the IP address cannot be assigned, this is shown as
“000.000.000.000”. In this case, consult the network
administrator.
To set the IP address
Set DHCP to “DISABLE” beforehand.
For details on settings, see “When the IP address is
assigned automatically” (page 109).
1
Select maintenance menu item M5: NETWORK
>M51: IP ADDRESS.
2
Press the PUSH SET knob.
The IP address appears, and the digit that can be
changed flashes.
3
Set the IP address.
To select a different digit to be changed
Use the B/IN and b/OUT buttons.
To change the value of a digit
Turn the PUSH SET knob.
Turning clockwise increases the value, and turning
counterclockwise decreases the value.
The V/MARK1 and v/MARK2 buttons can also be
used.
Arrow buttons
MENU button
Function buttons (F1 to F6) PUSH SET knob
SHIFT buttonPAGE/HOME
button
Note
Note
110 Maintenance Menu
Chapter 7 Menus
To return to the factory default setting
Press the RESET button.
4
When all digits are set, press the SAVE function
button (F5).
This returns to the NETWORK menu.
5
Repeat steps 1 to 4 as required, to set the subnet mask
and default gateway.
6
In the NETWORK menu, press the SAVE function
button (F5).
7
When the message “NETWORK CONFIG WAS
CHANGED. PLEASE REPOWER.” appears, power
the unit off and then on again with the on/standby
button.
To set the communications speed and
protocol
Set the communications speed and protocol (LINK
SPEED) to match the network environment.
To set the communications speed and protocol, proceed as
explained in “To display the maintenance menu”
(page 108) to display the NETWORK menu and then
proceed as follows.
Contact your network administrator if you have any
questions about the proper settings for these items.
1
Select maintenance menu item M5: NETWORK
>M54: LINK SPEED.
2
Press the PUSH SET knob.
Combinations of the communications speed and
protocol (1Gbps FullDuplex, 100Mbps FullDuplex,
100Mbps HalfDuplex, 10Mbps FullDuplex, 10Mbps
HalfDuplex) appear, and the arrow flashes.
3
Press the PUSH SET knob or use the V/MARK1 or
v/MARK2 button to select a combination of
communications speed and protocol.
To return to the factory default setting
Press the RESET button.
4
Press the SAVE function button (F5).
This returns to the NETWORK menu.
5
In the NETWORK menu, press the SAVE function
button (F5).
6
When the message “NETWORK CONFIG WAS
CHANGED. PLEASE REPOWER.” appears, power
the unit off and then on again with the on/standby
button.
111
Important Notes on Operation
Appendix
Appendix
Important Notes on
Operation
Use and storage
Do not subject the unit to severe shocks
The internal mechanism may be damaged or the body
warped.
Do not cover the unit while operating
Doing so will cause temperatures to rise inside the unit,
possibly resulting in failure.
After use
Turn off the on/standby button.
If you plan not to use the unit for a long time, turn off the
POWER switch on the rear panel as well.
Shipping
• Remove the disc before transporting the unit.
• If sending the unit by truck, ship, air or other
transportation service, pack it in the shipping carton of
the unit.
Care of the unit
If the body of the unit is dirty, clean it with a soft, dry cloth.
In extreme cases, use a cloth steeped in a little neutral
detergent, then wipe dry. Do not use organic solvents such
as alcohol or thinners, as these may cause discoloration or
other damage to the finish of the unit.
In the event of operating problems
If you should experience problems with the unit, contact
your Sony representative.
Use and storage locations
Store in a level, ventilated place. Avoid using or storing the
unit in the following places.
• In excessive heat or cold (operating temperature range:
5°C to 40°C (41°F to 104°F))
Remember that in summer or in warm climates the
temperature inside a car with the windows closed can
easily exceed 50 °C (122 °F).
• In damp or dusty locations
• Locations where the unit may be exposed to rain
• Locations subject to violent vibration
• Near strong magnetic fields
• Close to radio or TV transmitters producing strong
electromagnetic fields.
• In direct sunlight or close to heaters for extended periods
To prevent electromagnetic interference from
portable communications devices
The use of portable telephones and other communications
devices near this unit can result in malfunctions and
interference with audio and video signals.
It is recommended that the portable communications
devices near this unit be powered off.
Consumable parts
The life expectancy of the electrolytic capacitor is about
5 years under normal operating temperatures and normal
usage (8 hours per day; 25 days per month). If usage
exceeds the above normal usage frequency, the life
expectancy may be reduced correspondingly.
Periodic parts replacement
The battery and optical head are consumable parts that will
need periodic replacement.
When operating at room temperature, a normal
replacement cycle will be about 5 years.
However, this replacement cycle represents only a general
guideline and does not imply that the life expectancy of
these parts is guaranteed. For details on parts replacement,
contact your dealer.
About the LCD panel
The LCD panel fitted to this unit is manufactured with high
precision technology, giving a functioning pixel ratio of at
least 99.99%. Thus a very small proportion of pixels may
be “stuck”, either always off (black), always on (red,
112 Periodic Maintenance
Appendix
green, or blue), or flashing. In addition, over a long period
of use, because of the physical characteristics of the liquid
crystal display, such “stuck” pixels may appear
spontaneously. These problems are not a malfunction.
Note that any such problems have no effect on recorded
data.
Condensation
If the unit is suddenly taken from a cold to a warm location,
or if ambient temperature suddenly rises, moisture may
form on the outer surface of the unit and/or inside of the
unit. This is known as condensation. If condensation
occurs, turn off the unit and wait until the condensation
clears before operating the unit. Operating the unit while
condensation is present may damage the unit.
Periodic Maintenance
Operating hours meter
The operating hours meter can provide two items of
information about the operational history of the unit. The
information can be displayed by text superimposition on
the monitor connected to the unit. Use the information as a
guide in scheduling periodic maintenance.
For periodic maintenance, consult a Sony service
representative.
Display modes of the operating hours
meter
H01: OPERATION HOURS mode
Displays the total number of hours the unit has been
powered on in units of 1 hour.
H02: LASER PARAMETER 0 mode (not
resettable)
Of the two optical heads, this shows a counter of the
cumulative light output time by one optical head in units of
hours.1)
This can be used as a guide in determining when to replace
the optical head.
1) The counter advances at different rates during recording and playback. It
is also affected by the ambient temperature.
H11: OPERATION HOURS mode (resettable)
Same as H01 except that the count is resettable.
This can be used as a guide in determining when to replace
parts.
H13: SEEK RUNNING HOURS 0 mode (resettable)
Of the two optical heads, this shows the cumulative seek
operation time for one optical head in units of hours. The
count is resettable.
This can be used as a guide in determining when to replace
the seek motor.
H14: SPINDLE RUNNING HOURS mode
(resettable)
This shows the cumulative spindle rotation time, in units of
hours. The count is resettable.
This can be used as a guide in determining when to replace
the spindle motor.
H15: LOADING COUNTER mode (resettable)
Display the total number of times disc has been loaded in
the unit. The count is resettable.
113
Periodic Maintenance
Appendix
To display the operating hours meter
Press the MENU button to display the setup menu, then
turn the PUSH SET knob to display the required item on
the monitor connected to the unit.
To exit from the operating hours meter
Press the RETURN function button (F1) to return to the
setup menu.
Press the EXIT function button (F6) to return to the screen
that was displayed before you entered the setup menu.
114 Troubleshooting
Appendix
Troubleshooting
Alarms
An alarm (warning message) appears in the status display
area when an operation is attempted which is inappropriate
for the settings on this unit or the state of media. Both the
alarm message and the action to take to resolve the
problem appear on the video monitor screen.
If “display off: DISPLAY KEY” appears below the alarm
display, you can press the DISPLAY button to dismiss the
alarm display.
When an alarm is displayed, remove the alarm cause by
following the action to take. If the alarm display does not
disappear, contact your Sony representative.
When the unit is powered on
When a disc is inserted
Note
Example alarm in status display area
Example alarm on video monitor screen
Alarm message in status
display area
Alarm message on video monitor
screen
Description/action
ILL. SETUP! INVALID SETTINGS SELECTED IN
SETUP MENU.
SET ITEMS IN THE SETUP MENU TO
THE APPROPRIATE VALUES.
CONTACT SERVICE IF THIS ALARM
APPEARS AGAIN AFTER ABOVE
PROCEDURE.
Reset the settings in the setup menu (see page 85).
If the same message appears after you reset the
settings, contact your Sony representative.
Exchg batt! BATTERY NEEDS REPLACING.
PLEASE CONTACT SERVICE.
The battery of the internal clock is low or dead.
Contact your Sony service or sales representative.
Run Software Update
Program.
RUN SOFTWARE UPDATE PROGRAM. The software update is not properly performed.
Update the software version again. If the same
message appears after you update the software
version, contact your Sony representative.
Alarm message in status
display area
Alarm message on video monitor
screen
Description/action
Unknown FS! UNKNOWN FILE SYSTEM.
PLEASE FORMAT DISC OR EJECT.
Format the disc (see page 64) or eject it (see
page 43).
ILL. Index! INDEX FILE ERROR.
PLEASE FORMAT DISC OR EJECT.
No FS! NO FILE SYSTEM.
PLEASE EJECT DISC.
Eject the disc.
ILL. Disc! IRREGULAR DISC IS USED.
PLEASE EJECT DISC.
Use another disc.
115
Troubleshooting
Appendix
When a memory card is inserted a)
Over DUR! EXCESSIVE DURATION IS IN DISC. The total amount of recorded data exceeds the
capacity of the disc.
No Support! FORMAT NOT SUPPORTED.
RECORDING AND PLAYBACK IS NOT
POSSIBLE.
This appears when a disc recorded in an
unsupported recording format has been inserted. Use
a disc that is supported by this unit.
DISC frequency mismatch! RECORDING AND PLAYBACK IS NOT
POSSIBLE.
SYSTEM SETTINGS DIFFERENT FROM
DISC.
This appears when the system frequency setting of
this unit and the system frequency of the inserted
disc do not coincide.
Replace the disc with one that is compatible with the
system frequency setting of this unit, or change the
system frequency setting of this unit.
1080/23.98P DISC DISC CANNOT BE RECORDED.
SYSTEM SETTINGS DIFFERENT FROM
DISC.
This appears when the system frequency setting of
this unit and the system frequency of the inserted
disc do not coincide. Only pulldown playback is
possible.
Replace the disc with one that is compatible with the
system frequency setting of this unit, or change the
system frequency setting of this unit.
REC INH! AUTO FORMATTING WAS NOT
COMPLETED.
THE DISC WRITE PROTECT TAB IS SET
TO SAVE.
PLEASE EJECT DISC.
Set the Write Inhibit tab on the disc so as to enable
recording (see page 43).
FORMAT NG! AUTO FORMATTING WAS NOT
COMPLETED.
Eject the disc and then insert it again or insert
another disc.
DI read err CANNOT READ DISC INFORMATION.
PLEASE EJECT DISC.
DRV ADJ err CANNOT PERFORM AUTO DRIVE
ADJUSTMENT.
Read err CANNOT READ DISC DATA.
PLEASE EJECT DISC.
BCA Read Error! CANNOT READ DISC BCA AREA.
PLEASE EJECT DISC.
DISC Error! DISC CANNOT BE RESTORED.
PLEASE RESTORE IT USING THE
RECORDED EQUIPMENT.
The inserted disc requires to be restored.
Eject the disc, and restore it or format it on another
XDCAM device.
XDROOT needs
Restoring.
DISC USERDATA XDROOT NEEDS TO
BE RESTORED.
An abnormality has occurred with the UserData
>XDROOT folder, and data restoration is needed.
Restore the XDROOT folder.
BPAV Error! USERDATA BPAV ERROR. You cannot use clips in the UserData >BPAV folder.
File System FILE SYSTEM ON THE DISC INHIBITS
WRITING.
Writing is inhibited by the file system.
Exchange the disc or format the disc in order to
record.
U1/U2 Disc! DISC CANNOT BE RESTORED.
PLEASE EJECT AND RESTORE BY
PDW-U1/U2.
A disc was inserted that requires restoring.
Eject the disc and restore the disc using an PDW-U1/
U2 unit, or format the disc.
Alarm message in status
display area
Alarm message on video monitor
screen
Description/action
Unknown Media(A) UNKNOWN MEDIA(A).
PLEASE CHANGE.
The inserted memory card has been partitioned, or it
contains more clips that the maximum that can be
handled by this unit.
Insert a memory card that has not been partitioned,
or one that contains fewer than the maximum number
of clips.
Alarm message in status
display area
Alarm message on video monitor
screen
Description/action
116 Troubleshooting
Appendix
a) You can use SxS memory cards by connecting the optional SBAC-US20/
US30 SxS Memory Card USB Reader/Writer.
When a folder in external storage is being mounted
During front panel operations
Memory (A) needs
Restoring.
MEDIA ERROR.
MEDIA(A) NEEDS TO BE RESTORED.
A memory card must be restored because an error
has occurred in the card.
Memory(A) Error! MEDIA(A) CANNOT BE RESTORED.
PLEASE RESTORE IT USING THE
RECORDED EQUIPMENT.
An abnormality has occurred on the memory card,
and data restoration is needed.
Perform data restoration on the device that was used
to record to the memory card.
Unknown FS!(A) CANNOT USE MEDIA(A).
UNSUPPORTED FILE SYSTEM.
The inserted memory card is formatted with an
unsupported file system, or it is not formatted.
Format the memory card, or exchange the memory
card for one that is formatted with a file system
supported by this unit.
R/W Limit(A) MEDIA REACHED REWRITE LIMIT.
CHANGE MEDIA(A).
The memory card has reached its lifetime rewriting
limit.
Copy clips on the memory card to other media as
required, and then exchange the memory card.
Over DUR!(A) EXCESSIVE DURATION IS IN
MEDIA(A).
A clip with a duration that exceeds 24 hours is
recorded on a memory card.
This memory card cannot be used.
Repair Failed (A) REPAIR FAILED. The memory card may be damaged, and cannot be
used.
Replace the memory card.
Alarm message in status
display area
Alarm message on video monitor
screen
Description/action
Alarm message in status
display area
Alarm message on video monitor
screen
Description/action
USB DRV Error! USB DRIVE CANNOT BE RESTORED.
PLEASE RESTORE IT USING THE
RECORDED EQUIPMENT.
The operation target folder in external storage needs
data restoration.
Perform data restoration on the device that was used
to record to external storage originally.
USB DRV needs
Restoring.
MEDIA ERROR.
USB DRIVE NEEDS TO BE RESTORED.
An abnormality has occurred with the operation target
folder on external storage or the folder was edited by
another device, and data restoration is needed.
Perform data restoration on the external storage
device or format it.
Over DUR!(USB DRV) EXCESSIVE DURATION IS IN USB
DRIVE.
The total length of the clips stored in the operation
target folder in external storage exceeds 24 hours.
This operation target folder cannot be used.
USB Drive not mounted
due to limit of files or
unsupported sector size.
– The number of files exceeds 20,000 or external
storage with an unsupported sector size is connected.
Replace with other external storage.
Alarm message in status
display area
Description/action
KEY INHI.! This appears when the KEY INHI switch is “ON”.
Set the KEY INHI switch to “OFF”.
Not Open Clip! This appears when a clip operation is attempted with no clip selected.
Select a clip on the clip list screen and try the operation again.
Clip Top! During playback, this appears if you execute a reverse search when the unit is stopped at the first
frame of a clip. To move to another clip, press the PREV, NEXT, SHIFT + PREV, or SHIFT + NEXT
button, or perform a thumbnail search.
117
Troubleshooting
Appendix
During recording operations
Clip End! During playback, this appears if you execute a forward search when the unit is stopped at the last
frame of a clip. To move to another clip, press the PREV, NEXT, SHIFT + PREV, or SHIFT + NEXT
button, or perform a thumbnail search.
EDL Top! During EDL playback, this appears if you press the PREV button at the first frame of the first sub
clip of an EDL.
EDL End! During EDL playback, this appears if you press the NEXT button at the last frame of the last sub
clip of an EDL.
MAX # Clips No more clips can be recorded because the maximum number of recorded clips has been
reached.
Delete unneeded clips.
Media Full! Recording or copying is not possible because the media is full.
Delete unneeded clips.
TC EXT! This appears when TCG on page P4 TC of the function menu is set to “EXT”, and you try to preset
timecode or user bits by setting PRST/RGN to “PRESET”.
Set TCG to “INT” (see page 41).
REGEN mode! This appears when PRST/RGN on page P4 TC of the function menu is set to “TC” or “VITC”, and
you try to preset timecode or user bits.
Set PRST/RGN to “PRESET” (see page 41).
REC mode! Stop recording and try again.
Exit THUMBNAIL mode! This appears when an attempt is made to change media while the clip list screen is displayed.
Switch to the basic operation screen or the video monitor screen and try the operation again.
REMOTE! Press the REMOTE button, turning it off, to put this unit into local control mode.
No Disc! Insert a Professional Disc and try the operation again.
Media Top! An attempt has been made to execute a reverse search when the unit is stopped at the first frame
of the first clip during playback of a disc.
Media End! An attempt has been made to execute a forward search when the unit is stopped at the last frame
of the last clip during playback of a disc.
REC INHI.! Set the Write Inhibit tab on the disc so as to enable recording (see page 43).
No EM Space This appears when any essence mark was not recorded because there is no space before and
after the desired position.
Delete unneeded shot marks 0 to 9 on the chapter thumbnail screen.
EM Full! This appears when no more essence marks can be recorded.
Delete unneeded shot marks 0 to 9 on the chapter thumbnail screen.
Illegal Operation! This appears when an attempt is made to carry out an invalid operation.
Media is not Ready. The media is in the course of being mounted or has not been loaded.
Alarm message in status
display area
Alarm message on video monitor
screen
Description/action
Input Sig! VIDEO INPUT SIGNAL DOES NOT
MATCH SYSTEM SETUP.
This appears when the signal that does not
correspond to the system frequency or the number of
lines set in this unit is being input, or when HD-SDI is
selected as a video input signal while set for SD
signal recording.
Input a signal that matches the system frequency, or
change this unit’s system frequency setting (see
page 34).
REC INH! THE DISC WRITE PROTECT TAB IS SET
TO SAVE.
Set the write protect tab of the disc to allow recording
(see page 43).
ILL. REC! ENCODING DOES NOT SYNCHRONIZE
WITH REF VIDEO.
Check the signals being input to this unit.
Alarm message in status
display area
Description/action
118 Troubleshooting
Appendix
During playback operations
During operations on the clip list screen/thumbnail search/EDL editing/copy
MEM. Full! MEMORY FULL !! Recording on the disc is not possible because a
buffer overflow has occurred in the recording buffer
memory.
Verify ERR! DISC ERROR DETECTED. The Verify function detected an abnormality in signals
recorded on the disc.
Replace the disc.
Disc Damage DISC CANNOT BE RECORDED TO.
USE ANOTHER DISC FOR RECORDING.
Use another disc.
Index File! UNSUPPORT INDEX FILE.
DISC CANNOT BE RECORDED TO.
Disc Busy! – A copy operation is being performed, so simultaneous
recording is impossible at present.
REC STOP WITHIN 2MIN RECORDING IS TERMINATED WITHIN 2
MINUTES AUTOMATICALLY.
BECAUSE THE CLIP IS REACHED TO
MAXIMUM DURATION.
The length of the clip has reached the maximum limit
during recording. Recording will stop within the next
two minutes.
RECORDING IS TERMINATED WITHIN 2
MINUTES AUTOMATICALLY.
BECAUSE OF INTERNAL LIMITATION.
The total recording time has reached the maximum
limit during recording. Recording will stop within the
next two minutes.
Cache Full! CACHE FULL.
DATA IS BEING OVERWRITTEN.
This appears when the memory becomes full while
performing the disc exchange cache function.
Change the disc immediately.
Alarm message in status
display area
Alarm message on video monitor
screen
Description/action
ILL. PLAY! ILLEGAL PLAYBACK. Normal playback is not possible.
MEM. Empty! MEMORY EMPTY !! Playback is not possible because a buffer underflow
has occurred in the playback buffer memory.
Media Data Error! MEDIA DATA ERROR DETECTED. A disc error has been detected.
Replace the disc.
Backup Disc UNCORRECTABLE ERROR HAS BEEN
DETECTED ON THE DISC.
PLEASE BACK UP THE DATA
(IMMEDIATELY).
An error was detected in the record signal of the disc.
Back up the data.
This Clip cannot be Played
back.
– This clip cannot be played back because its format is
not supported by this unit.
No clips in the UserData folder can be played back.
No MEDIA! – Insert a disc and try the operation again.
Operation is not
Supported for EDL.
– An EDL cannot be played back.
Select a clip.
Disc Busy!
NETWORK
– The disc cannot be played as it is currently being
used on the network.
Alarm message on clip
list screen
Description/action
Clip is Locked. The clip is locked.
This appears when an attempt is made to delete a clip, or set or clear a clip flag when the clip is
locked.
Copy Running! A copy operation is being performed, so another copy operation is not allowed.
Operation Failed! The target operation failed because of generation of an internal error.
Alarm message in status
display area
Alarm message on video monitor
screen
Description/action
119
Troubleshooting
Appendix
Not Supported Format. The format is not supported by this unit, so copy operation is not possible.
Copy Aborted. The copy operation was aborted.
Some Clip(s) are Locked. Some of the selected clips are locked (protected).
Clip Error. The clip is defective, so the copy operation failed.
The Disc Protect TAB is
Set to Save.
You have attempted to format a disc whose Write Inhibit tab is set so as to disable recording.
To execute formatting, set the Write Inhibit tab on the disc so as to enable recording.
Irregular Disc is in Use.
Use Professional Disc.
The inserted disc cannot be recorded/played back on this unit.
Insert a disc that can be recorded/played back on this unit.
Set Appropriate IN/OUT
Points.
The settings of IN and OUT points for partial copy operation are invalid.
Check the IN and OUT point settings.
No Clip! The clip selected for expansion or chapter display has been deleted. Alternatively, the disc has
been ejected.
Cannot Expand Clip any
Further.
The selected clip cannot be divided any further to display the expanded thumbnails.
This alarm appears when the expanded thumbnails of a clip divided into the maximum number of
blocks are displayed or when the EXPAND function button has been pressed with the expanded
thumbnail screen displayed in which the duration of each block is one frame.
Delete is Prohibited.
This Clip is in Use.
The target clip is being used, so it cannot be deleted.
Delete is Prohibited.
Referring EDL is in Use.
The EDL which refers to the target clip is being used, so the clip cannot be deleted.
Delete is Prohibited. Deletion of the target clip has failed.
Lock/Unlock is Prohibited.
This Clip is in Use.
The target clip is being used, so it cannot be locked/unlocked.
Lock/Unlock is Prohibited. Locking/unlocking of the target clip has failed.
Set Clip Flag was not
Performed.
Set Clip Flag function has failed.
One Clip is being
Recorded.
Use Single Selection.
One of the selected clips was being recorded.
To copy a clip which is being recorded, make a single selection of the clip.
Operation is not
Supported for EDL.
You cannot select EDL to delete an essence mark or set a shot mark.
Operation is not
Supported for this Folder.
You cannot delete or lock/unlock any clip in the UserData >BPAV folder.
Adding EM was not
Performed.
Essence mark setting has failed.
Over DUR! A clip with a duration that exceeds six hours cannot be copied.
Copy to /Clip is not
Permitted.
Change Dest to
/UserData.
The selected clip cannot be copied to the Clip folder.
Change the copy destination to the UserData folder.
Dest was Changed to
/UserData.
Copy to /Clip is not
Permitted.
The selected clip was not permitted to be copied to the Clip folder, so it was copied to the UserData
folder.
Cannot Display Chapter of
this Clip.
Display of the selected clip on the chapter thumbnail screen has failed.
Stop recording of a clip if any in progress.
Chapter was Changed.
Display Again.
The chapter setting information has been updated.
Try again the chapter thumbnail display.
Disc Busy! The Professional Disc was being used, so copying was not possible.
Chapter does not Exist. Chapter thumbnail screen cannot be displayed because no chapters are set on the clip.
Cannot Expand this Clip. The clip cannot be expanded because it is being recorded.
Alarm message on clip
list screen
Description/action
120 Troubleshooting
Appendix
Alarms relating to audio and video signals
Alarms relating to sensors and drivers
Other alarms
Unable to Parse the EDL. The EDL cannot be copied due to the existence of an inhibiting condition, such as a missing sub
clip.
Writing this AV Format to
DISC is not Permitted.
This clip cannot be copied to the currently loaded Professional Disc because of its format.
Out of Remain Space! The remaining capacity of the copy destination media is not sufficient.
Alarm message in status
display area
Alarm message on video monitor
screen
Description/action
No INPUT! INPUT VIDEO IS NOT DETECTED.
CHECK THE VIDEO INPUT MODE AND
SUPPLY A VIDEO SIGNAL TO VIDEO
INPUT.
• Check the setting of V INPUT on page P1 INPUT of
the function menu (see page 40).
• Input an HDSDI signal.
EMPHASIS! INPUT AUDIO EMPHASIS IS NOT
SUPPORTED.
CHECK THE EMPHASIS OF THE AUDIO
INPUT SIGNAL.
Check the emphasis of the audio input signal.
REF Not Exist – Input a reference signal.
REF NON-STD A NON-STANDARD REF SIGNAL IS
BEING USED FOR REF VIDEO.
USE A STANDARD SIGNAL.
Input a standard reference signal.
Alarm message in status
display area
Alarm message on video monitor
screen
Description/action
MEM-138 Warning IT IS NESSESARY TO REPLACE MEM-
138.
PLEASE CONTACT SERVICE.
Contact your Sony representative.
Note
The unit will not stop operating, but if you continue to
use it in this state, it may fail, resulting in a total loss of
the information.
FAN(1/2/3) Error FAN1(1/2/3) ERROR. Contact your Sony representative.
Note
The unit will not stop operating, but if you continue to
use it in this state, temperatures inside the unit will
rise, possibly resulting in failure or fire.
FAN1 Warning FAN1 WARNING.
DR-FAN Stop DRIVE FAN MOTOR STOPPED.
High TEMP! HIGH TEMPERATURE IN DRIVE.
HIGH TEMPERATURE.
LASER 0 Lifetime DISC DRIVE LASER 0 LIFETIME HAS
ENDED.
PLEASE CONTACT SERVICE.
The lifetime of the Professional Disc drive laser has
come to an end.
Contact your Sony service or sales representative.
Alarm message in status
display area
Alarm message on video monitor
screen
Description/action
Turn off/on POWER!! SYSTEM CONFIGURATION WAS
CHANGED.
PLEASE TURN OFF/ON POWER.
The system frequency was changed.
Power off this unit and then power it on again.
Turn off/on POWER!! MENU CONFIG WAS CHANGED.
PLEASE TURN OFF/ON POWER.
Menu settings were changed.
To apply menu settings, power this unit off and then
power it on again.
Completed only XML file – Only the metadata file was updated, without updating
the metadata in the MXF file.
Alarm message on clip
list screen
Description/action
121
Troubleshooting
Appendix
Error messages
Error codes appear in the status display area when an error
(usually a hardware problem) occurs. In addition, both
error messages and error codes appear on the video
monitor screen.
When an error message appears, follow the instructions in
the error message to resolve the problem.
If “display off: DISPLAY KEY” appears below the error
display, you can press the DISPLAY button to dismiss the
error display. In this case, the error is displayed only in the
status display area, on the video monitor screen, and on a
PC monitor connected to the unit.
Format Media is
Prohibited.
Confirm Mainte Menu :
M395.
– An attempt was made to execute Format Media while
use of the Format Media command is prohibited by
maintenance menu item M395.
Check maintenance menu item M395.
Cannot finalize this Disc.
It is available for QL-WO
disc only.
– An attempt has been made to finalize a disc that
cannot be finalized.
Only quad-layer discs can be finalized.
Alarm message in status
display area
Alarm message on video monitor
screen
Description/action
Note
Error code
Example error code in status display area
Error code
Example error message on video monitor
122 Specifications
Appendix
Specifications
General
External dimensions (w/h/d, excluding projections)
210 × 132 × 420 mm
(8
3
/
8
× 5
1
/
4
× 16
5
/
8
inches)
Mass 6.6 kg (14 lb 8.8 oz)
Power requirements
100 V to 240 V AC, 50/60 Hz
12 V DC
Power consumption
AC operation: 100 W
DC operation: 7.5 A
Inrush current
(1) Maximum possible inrush current at
initial switch-on (Voltage changes
caused by manual switching):
47 A peak, 7.6 A r.m.s. (240 V AC)
(2) Inrush current after a mains
interruption of five seconds (Voltage
changes caused at zero-crossing):
12 A peak, 4 A r.m.s. (240 V AC)
Operating temperature
5 ºC to 40 ºC (41 ºF to 104 ºF)
Storage temperature
–20 ºC to +60 ºC (–4 ºF to +140 ºF)
Operating humidity
20% to 90% (relative humidity)
Storage humidity
5% to 80% (relative humidity)
System
Recording/playback format
XAVC (option)
Video MPEG-4 AVC/H.264, Intra CLASS 100
Max. 112 Mbps (for frame frequencies of
59.94i, 50i, 29.97P, 25P)
Max. 89 Mbps (for frame frequencies of
23.98P)
Audio 24-bit, 48 kHz, 8 channels
MPEG HD422
Video MPEG HD422: 50 Mbps
Proxy video MPEG-4
Audio 24-bit, 48 kHz, 8 channels
Proxy audio A-law 8-bit, 8 kHz, 8 channels
MPEG HD
Video MPEG HD: HQ35/SP25/LP18 Mbps 1)
Proxy video MPEG-4
Audio 16-bit, 48 kHz, 2/4 channels
Proxy audio A-law 8-bit, 8 kHz, 2/4 channels
MPEG IMX
Video MPEG IMX: 50/40/30 Mbps 2)
Proxy video MPEG-4
Audio 24/16-bit, 48 kHz, 4/8 channels
Proxy audio A-law 8-bit, 8 kHz, 4/8 channels
DVCAM
Video DVCAM: 25 Mbps
Proxy video MPEG-4
Audio 16-bit, 48 kHz, 4 channels
Proxy audio A-law 8-bit, 8 kHz, 4 channels
1) MPEG HD 18 Mbps can be used for playback only.
2) MPEG IMX 40 Mbps can be used for playback only.
Unit: mm (inches)
210 (8 3/8)
132 (5 1/4)
420 (16 5/8)
123
Specifications
Appendix
Recording/playback times
The actual recording and playback time may differ slightly
from the values shown here, depending on usage
conditions, etc.
Please take the following table on recording and playback
time as a guide.
a) When the optional XDBK-106 is installed.
Search speed
Jog mode –1 to +1 times normal speed
During remote control:
–2 to +2 times normal speed
(excluding XAVC)
–1 to +2 times normal speed (XAVC)
Variable mode –2 to +2 times normal speed (excluding
XAVC)
–1 to +2 times normal speed (XAVC)
Shuttle mode –20 to +20 times normal speed
During remote control: –50 to +50 times
normal speed
F. FWD mode +50 times normal speed
F. REV mode –50 times normal speed
Video performance
Sampling frequency
Y: 74.25 MHz, R–Y/B–Y: 37.125 MHz
Quantization MPEG HD422/MPEG HD: 8 bits/sample
XAVC: 10 bits/sample
Compression HD422 MPEG-2 422P@HL
HD: MPEG-2 MP@HL/H-14
XAVC: MPEG-4 AVC/H.264 Intra
Composite output
Frequency response
0.5 to 5.75 MHz +0.5/–2.0 dB
S/N (Y) 53 dB or more
Y/C delay ±20 ns or less
K-factor (K2T) 1.0% or less
Processor adjustment range
Video level –∞ to +3 dB
Chroma level –∞ to +3 dB
Set up/black level
±30 IRE/±210 mV
Chroma phase ±30°
System phase SYNC: ±15 µs
SC: 0 to +400 ns
Audio performance
Sampling frequency
48 kHz
Quantization 24 bits
Headroom –20/–18/–16/–12/–9 (EBU level)
(selectable)
Frequency response
20 Hz to 20 kHz +0.5/–1.0 dB (0 dB at
1kHz)
Dynamic range 90 dB or more
Distortion 0.05% or less (at 1 kHz)
Note
Recording formats
XAVC AI422 a) MPEG HD422 MPEG HD MPEG IMX DVCAM
Recording modes CLASS 100 50 Mbps HQ mode
(35 Mbps/VBR)
50 Mbps 25 Mbps
Number of audio
channels
882/44/84
Recording
and
playback
time
PFD23A Approx.
21 minutes
Approx.
43 minutes
Approx.
65 minutes
Approx.
45 minutes
Approx.
85 minutes
PFD50DLA Approx.
46 minutes
Approx.
95 minutes
Approx.
145 minutes
Approx.
100 minutes
Approx.
185 minutes
PFD100TLA Approx.
92 minutes
Approx.
190 minutes
Approx.
290 minutes
Approx.
200 minutes
Approx.
370 minutes
PFD128QLW Approx.
120 minutes
Approx.
240 minutes
Approx.
360 minutes
Approx.
240 minutes
Approx.
450 minutes
124 Specifications
Appendix
Input connectors
Digital video inputs
SD/HDSDI INPUT
BNC type, complying with SMPTE ST
259 (SD)/SMPTE ST 292-1 (HD)
Analog video inputs
REF.VIDEO INPUT
BNC type (2) (loop-through), HD Tri-
level sync (0.6 Vp-p, 75 Ω, sync
positive/negative), SD black burst, or
SD composite sync (0.286 Vp-p
(NTSC), 0.3 Vp-p (PAL), 75 Ω, sync
negative)
Digital audio inputs
DIGITAL AUDIO (AES/EBU) IN 1/2, 3/4
BNC type (2), channels 1/2, 3/4,
complying with AES-3id-1995
Analog audio inputs
ANALOG AUDIO INPUT 1, 2
XLR 3-pin, female (2), +4 dBu, high
impedance, balanced
ANALOG AUDIO INPUT 3, 4
XLR 3-pin, male (2), +4 dBu, high
impedance, balanced
ANALOG AUDIO OUTPUT switching
with maintenance menu item M374
ANALOG I/O
Timecode input
TIME CODE IN
BNC type, SMPTE timecode, 0.5 to
18 Vp-p, 3.3 kΩ, unbalanced
Output connectors
Digital video outputs
HDSDI OUTPUT 1, 2 (SUPER)
BNC type (2), complying with SMPTE
ST 292-1
SDSDI OUTPUT 1, 2 (SUPER)
BNC type (2), complying with SMPTE
ST 259
HDMI OUT Type A 19-pin
Video: 1080i, 720P, 480i, 480P, 576i,
576P
Audio: Linear PCM, 48kHz/16-bit,
2 channels
Analog video outputs
COMPOSITE OUTPUT 1, 2 (SUPER)
BNC type (2), 1.0 Vp-p, 75 Ω, sync
negative, complying with SMPTE ST
170
Digital audio outputs
DIGITAL AUDIO (AES/EBU) OUT 1/2, 3/4
BNC type (2), channels 1/2, 3/4,
complying with AES-3id-1995
Analog audio outputs
ANALOG AUDIO OUTPUT 1, 2
XLR 3-pin, male (2), +4 dBu, 600 Ω
load, low impedance, balanced
AUDIO MONITOR
XLR 3-pin, male (2), +4 dBu, 600 Ω
load, low impedance, balanced
PHONES Stereo phone jack, –∞ to –13 dBu, 8 Ω,
unbalanced
Timecode output
TIME CODE OUT
BNC type, SMPTE timecode, 1.0 Vp-p,
75 Ω, unbalanced
Remote control connectors
REMOTE (9P) D-sub 9-pin, female, complying with
RS-422A
REMOTE 4-pin, female
12 V DC, 7.5 W
(Network) RJ-45 type
1000BASE-T: complying with
IEEE802.3ab
100BASE-TX: complying with
IEEE802.3u
10BASE-T: complying with IEEE802.3
USB connectors
USB 3.0 (front)
Super Speed USB (USB 3.0) Type-A
MAINTENANCE (rear)
High Speed USB (USB 2.0) Type-A (2)
Accessories supplied
Operation Guide (1)
CD-ROM manual (1)
Accessories not supplied
AC power cord
• For the customers in the U.S.A and Canada
Part number 1-551-812-31 (125 V, 10 A, about 2.4 m)
• For the customers in the United Kingdom
Part number 1-833-259-12 (250 V, 10 A, about 2.0 m)
• For the customers in European countries other than the
United Kingdom
Part number 1-551-631-16 (250 V, 10 A, about 2.0 m)
RCC-5G 9-pin Remote Control Cable
RM-280 Remote Edit Controller
BP-FL75/FLX75 Battery Pack
125
Specifications
Appendix
BKP-L551 Battery Adaptor
PFD23A Professional Disc
PFD50DLA Dual-Layer Professional Disc
PFD100TLA Triple-Layer Professional Disc
PFD128QLW Quad-Layer Write-Once Professional Disc
XDBK-106 XAVC Codec Option
SBAC-US30 SxS Memory Card USB Reader/Writer
SxS memory cards
SxS PRO+ series
SxS PRO series
SxS-1 series
XQD memory card series
QDA-EX1 XQD Express Card Adapter
Design and specifications are subject to change without
notice.
SONY WILL NOT BE LIABLE FOR DAMAGES OF
ANY KIND RESULTING FROM A FAILURE TO
IMPLEMENT PROPER SECURITY MEASURES ON
TRANSMISSION DEVICES, UNAVOIDABLE
DATA LEAKS RESULTING FROM
TRANSMISSION SPECIFICATIONS, OR
SECURITY PROBLEMS OF ANY KIND.
Notes
• Always make a test recording, and verify that it was
recorded successfully.
SONY WILL NOT BE LIABLE FOR DAMAGES
OF ANY KIND INCLUDING, BUT NOT LIMITED
TO, COMPENSATION OR REIMBURSEMENT
ON ACCOUNT OF FAILURE OF THIS UNIT OR
ITS RECORDING MEDIA, EXTERNAL
STORAGE SYSTEMS OR ANY OTHER MEDIA
OR STORAGE SYSTEMS TO RECORD
CONTENT OF ANY TYPE.
• Always verify that the unit is operating properly
before use. SONY WILL NOT BE LIABLE FOR
DAMAGES OF ANY KIND INCLUDING, BUT
NOT LIMITED TO, COMPENSATION OR
REIMBURSEMENT ON ACCOUNT OF THE
LOSS OF PRESENT OR PROSPECTIVE PROFITS
DUE TO FAILURE OF THIS UNIT, EITHER
DURING THE WARRANTY PERIOD OR AFTER
EXPIRATION OF THE WARRANTY, OR FOR
ANY OTHER REASON WHATSOEVER.
• SONY WILL NOT BE LIABLE FOR CLAIMS OF
ANY KIND MADE BY USERS OF THIS UNIT OR
MADE BY THIRD PARTIES.
• SONY WILL NOT BE LIABLE FOR THE LOSS,
REPAIR, OR REPRODUCTION OF ANY DATA
RECORDED ON THE INTERNAL STORAGE
SYSTEM, RECORDING MEDIA, EXTERNAL
STORAGE SYSTEMS OR ANY OTHER MEDIA
OR STORAGE SYSTEMS.
• SONY WILL NOT BE LIABLE FOR THE
TERMINATION OR DISCONTINUATION OF
ANY SERVICES RELATED TO THIS UNIT THAT
MAY RESULT DUE TO CIRCUMSTANCES OF
ANY KIND.
126 Using UMID Data
Appendix
Using UMID Data
Metadata is additional information recorded on discs along
with audio-visual data. It is used to bring greater efficiency
to the flow of operations from material acquisition through
editing, and to make it easier to find and reuse material.
UMID has been internationally standardized as a specific
application using metadata.
What is a UMID?
A UMID (Unique Material Identifier) is a unique identifier
for audio-visual material defined by the SMPTE ST
330:2004 standard.
A UMID may be either a 32-byte Basic UMID or an
Extended UMID, which includes an additional 32 bytes of
Source Pack data to make a total 64 bytes.
For details, refer to SMPTE ST 330.
A globally unique ID is automatically recorded for every
clip.
The Extended UMID is metadata that provides additional
information such as location, time/date, company ID and
so on.
The UMID is applied as follows.
Using the Extended UMID
You have to enter a country code, organization code and
user code. Set the country code referring to the table in ISO
3166, and set the organization code and user code
according to the guidelines of your organization.
For details, see “Setting UMID ownership information”
(page 127).
Functions of UMID data
UMID data enables the following:
• Addition of a globally unique ID to every clip of audio-
visual material. The unique ID is used to detect the
material source and to link it with the original source
material.
• Distinguishing between original material and copied
material. 00 is added to the Instance Number for original
material.
Extended UMID (64 bytes)
Basic UMID (32 bytes) Source Pack (32 bytes)
Universal label L Instance
No. Material Number Time/Date Spatial
Coordinates
Country
Org User
12 bytes 13 bytes 16 bytes 8 bytes 12 bytes 4 bytes 4 bytes 4 bytes
Instance No.
Material No.
ID generated when
shooting
Same as the above
Source Pack
Shooting
information (when,
where and who)
Same as the above
Original material: 00 00 00
Copied material: generation number (1 byte)
+ random number (2 bytes)
Distinguish between the
original material and copied
material
Material source ID/
detecting material
Metadata pack that
identifies the source of
material unit by defining the
when, where and who of
the material unit with which
it is associated.
127
Using UMID Data
Appendix
• Recording with UTC time. UTC (coordinated universal
time) is used when recording the UMID. Use of a
universal time system enables uniform management of
source material recorded all over the world.
• Calculation of date differences. Source material is
recorded using modified Julian dates (MJD), which
enables easy calculation of date differences between
different source material items.
Setting UMID ownership information
Proceed as follows.
1
Set setup menu item 029 STORED OWNERSHIP to
“on” (see page 88).
See page 89 for more information about setup menu
operations.
The STORED OWNERSHIP (UMID ownership
information setting) screen appears.
COUNTRY: Sets the country code.
ORGANIZATION: Sets the organization code.
USER: Sets the user code
See “About UMID ownership information”
(page 127) for more information about these codes.
2
Use the PUSH SET knob to select the item to set and
the character input location, then press the knob.
3
Use the PUSH SET knob, – or + function button (F3 or
F4) to select characters to input at the selected
location.
To delete all input data
Press the RESET/RETURN button.
4
Press SAVE function button (F5).
The message “NOW SAVING...” appears, and the
ownership information is saved.
About UMID ownership information
COUNTRY (country code)
Set the country code by entering an abbreviated
alphanumeric string (4-byte alphanumeric string)
according to the values defined in ISO 3166-1.
There are about 240 country codes.
Find your own country code on the following web page.
Refer to ISO 3166-1:
http://www.iso.org/iso/country-codes/
iso_3166_code_lists.htm
When the country code is less than 4 bytes, the active part
of the code occupies the first part of the 4 bytes and the
remainder must be filled with the space character (20h).
Example: Japan
For Japan, the country code is JP, which is 2 bytes, or JPN,
which is 3 bytes.
Thus, enter the following:
JP_ _
or
JPN _
where _ represents a space.
ORGANIZATION (organization code)
Enter a 4-byte alphanumeric string for the organization
code.
• There are no problems in recording or playing back
audio-video signals, even if the ORGANIZATION is not
set.
• Organization codes must be acquired by applying to the
SMPTE registration office. When no organization code
has been acquired, it is forbidden to enter an arbitrary
string. As a rule, the code “00” must be entered.
Freelance operators who do not belong to an origination
should enter “˜”.
USER (user code)
Enter a 4-byte alphanumeric string to identify the user.
The user code is registered with each organization locally.
It is usually not registered centrally.
When the user code is less than 4 bytes, enter the user code
at the beginning of the 4 bytes and fill the remainder of the
string with the space characters (20h).
This user code is determined by the organization. The
methods used depend on the organization.
A user code cannot be entered when no organization code
has been entered.
Notes
Note
128 Ancillary Data
Appendix
Ancillary Data
This unit can play and record ancillary data superimposed
on the HDSDI signals. It can also input and output
ancillary data in MXF files when transferring files via
FTP/CIFS connections. Transferable auxiliary data
includes text data (captions and metadata) and control
signals.
Ancillary data in HDSDI/SDSDI
signals
This unit can record and play back closed captions
conforming to the EIA-708-B 1) standard and EIA-608-
B1) standard, and text data conforming to the ARIB TR
B-23 2) standard which comprise the VANC (Vertical
ancillary data) packets.
1) EIA: Electronic Industries Alliance
2) ARIB: Association of Radio Industries and Businesses
To record ancillary data
Set the lines where ancillary data is inserted, the DID (Data
Identifier word), and the SDID (Secondary Data Identifier
word) with maintenance menu item M3B VANC RX
PARAMETER.
For details, see maintenance menu item M3B (page 106).
To record and play back auxiliary data of the
specified line
Specify the line on which the auxiliary data is recorded
using maintenance menu item M3B1 and M3B2.
Auxiliary data is recorded and played back regardless of
the DID/SDID setting values.
To record and play back EIA-708-B standard
closed caption data in HDSDI signals
Configure the following settings using the sub items of
maintenance menu item M3B0 VANC RX PACKET.
Example: When specifying line 9
• LINE (line selection): 9LINE
• DID (data identifier word): 61h
• SDID (secondary data identifier word): 01h
To record EIA-608-B standard closed caption
data in HDSDI signals
Configure the following settings using the sub items of
maintenance menu item M3B0 VANC RX PACKET.
Example: When specifying line 9
• LINE (line selection): 9LINE
• DID (data identifier word): 61h
• SDID (secondary data identifier word): 02h
VANC packets
• The Japanese ARIB TR-B23 standard limits the number
of packets that can be superimposed on the HDSDI
signal to 4 packets per line.
• The number of VANC packets that can be recorded,
depending on the relevant maintenance menu settings, is
limited to 9 packets per frame for 50P or 59.94P mode
and 18 packets per frame for other modes.
• When VANC packets are not continuous from word 0
and there is unused area on the line, then information
about the packet position is not recorded. Packets are
output flush left.
• During input, if a parity error is detected in a VANC
packet, the packet is discarded and recorded flush left.
Ancillary data in MXF files
VANC ancillary data recorded from an HDSDI signal is
inserted to an MXF file as an ANC Frame Element
(conforming to the SMPTE ST 436:2006). This data can
also be recorded on the disc from an MXF file that has
been input via CIFS/FTP.
To insert ancillary data into MXF files for
output
In setup menu item 666 METADATA ITEM OUT, select
“on”.
HANC/VANC packets
Detection of HANC/VANC packets
When an MXF file has been input, HANC/VANC packets
are recorded on the disc if the DATA ITEM of the head
frame is identified as ANC Frame Elements conforming to
the SMPTE ST 436:2006.
129
Ancillary Data
Appendix
Closed caption data
This section explains the closed caption data that can be
recorded, played back, and output during EE output.
Normal EIA-708/608 recording and playback
Closed caption input data that complies with the EIA-708/
608 standards can be recorded, played back, and output
with no changes.
However, settings are required for recording of closed
caption data in HDSDI signals.
For details, see “To record and play back EIA-708-B
standard closed caption data in HDSDI signals”
(page 128) or “To record EIA-608-B standard closed
caption data in HDSDI signals” (page 128).
EIA-708/608 standard closed caption data recorded in HD
video is output as HDSDI signals, regardless of menu
settings.
EIA-608 standard closed caption data in SDSDI line 21
signals are recorded and played back (output as SDSDI or
composite signals), regardless of menu settings.
EIA-708/608 EE output
Closed caption input data that complies with the EIA-708/
608 standard can be output in EE mode.
However, settings are required for EE output of closed
caption data in HDSDI signals.
For details, see “To record and play back EIA-708-B
standard closed caption data in HDSDI signals”
(page 128) or “To record EIA-608-B standard closed
caption data in HDSDI signals” (page 128).
Closed caption data in SDSDI line 21 signals are output in
EE mode (output as SDSDI or composite signals),
regardless of menu settings.
EE output of closed caption data in HDSDI signals is
delayed by 1 frame with respect to EE output of the video
signals.
EIA-708/608 recording and playback
EIA-608 recording and playback
HDSDI (VANC) input
SDSDI (line 21) input
HDSDI (VANC) output
SDSDI (line 21) output
Composite (line 21) output
Note
HDSDI (VANC) input HDSDI (VANC) output
SDSDI (line 21) input SDSDI (line 21) output
Composite (line 21) output
130 Trademarks and Licenses
Appendix
Trademarks and Licenses
Trademarks
• XAVC™, XAVC logo, MPEG HD422, and DVCAM
are trademarks of Sony Corporation.
• Professional Disc is a trademark of Sony Corporation.
• SxS, SxS PRO, SxS PRO+, SxS-1, and XQD are
trademarks of Sony Corporation.
• MPEG HD and HDCAM are registered trademarks of
Sony Corporation.
• The terms HDMI and HDMI High-Definition
Multimedia Interface, and the HDMI Logo are
trademarks or registered trademarks of HDMI Licensing
LLC in the United States and other countries.
• The ExpressCard word mark and logo are owned by
Personal Computer Memory Card International
Association (PCMCIA) and licensed to Sony. Other
trademarks and trade names are properties of their
respective owners.
• Adobe, Acrobat, and Adobe Reader are trademarks of
Adobe Systems Incorporated in the United States and/or
other countries.
MPEG-4 visual patent portfolio
license
THIS PRODUCT IS LICENSED UNDER THE MPEG-4
VISUAL PATENT PORTFOLIO LICENSE FOR THE
PERSONAL AND NON-COMMERCIAL USE OF A
CONSUMER FOR
(i) ENCODING VIDEO IN COMPLIANCE WITH THE
MPEG-4 VISUAL STANDARD (“MPEG-4 VIDEO”)
AND/OR
(ii) DECODING MPEG-4 VIDEO THAT WAS
ENCODED BY A CONSUMER ENGAGED IN A
PERSONAL AND NON-COMMERCIAL ACTIVITY
AND/OR WAS OBTAINED FROM A VIDEO
PROVIDER LICENSED BY MPEG LA TO PROVIDE
MPEG-4 VIDEO.
NO LICENSE IS GRANTED OR SHALL BE IMPLIED
FOR ANY OTHER USE. ADDITIONAL
INFORMATION INCLUDING THAT RELATING TO
PROMOTIONAL, INTERNAL AND COMMERCIAL
USES AND LICENSING MAY BE OBTAINED FROM
MPEG LA, LLC. SEE HTTP://WWW.MPEGLA.COM
MPEG LA is offering licenses for (i) manufacturing/sales of any storage
media storing MPEG-4 Visual video information (ii) distribution/
broadcasting of MPEG-4 Visual video information in any manner (such as
online video distribution service, internet broadcasting, TV broadcasting).
Other usage of this product may be required to obtain license from
MPEGLA. Please contact MPEG LA for any further information. MPEG LA,
L.L.C., 250 STEELE STREET, SUITE 300, DENVER, COLORADO
80206, http://www.mpegla.com
About IJG (Independent JPEG
Group)
This software is based in part on the work of the
Independent JPEG Group.
Character display software “iType”
This product includes technology from Monotype Imaging
Inc., including iType® and certain fonts.
Open source software licenses
On the basis of license contracts between Sony and the
software copyright holders, this product uses open
software.
To meet the requirements of the software copyright
holders, Sony is obligated to inform you of the content of
these licenses.
For the content of these licenses, see the PDF files in the
“License” folder of the supplied CD-ROM.
Obtaining GPL/LGPL/GPL V3
licensed software
This product uses software licensed under GPL version 2 /
LGPL version 2.1 / GPL version 3. You have the right to
obtain, change, and distribute the source code of this
software.
You can download the source code of this software from
Sony Internet servers. Access the following URL, and
refer to “PDW-HD1550”.
http://oss.sony.net/Products/Linux/common/search.html
We cannot respond to inquiries regarding the content of
the source code.
131
Index
Index
Index
A
AC IN connector 21
ACCESS indicator 11
Accessories
not supplied 124
supplied 124
Alarms 114
ANALOG AUDIO
INPUT 1, 2 connectors 21
OUTPUT 1, 2 connectors 22
Analog audio signal input/output
section 21
Ancillary data 128
Appendix 111
Arrow buttons 12
Audio
input display 15
Audio level
adjustment section 11
meters 15
AUDIO MONITOR R, L connectors
22
B
Basic menu 85
changing settings 90
items 86
operations 89
returning to factory default
settings 91
Battery
attaching a battery pack 23
checking the remaining power 24
removing 24
C
CH-1/ALL CH, CH-2 to CH-4
adjustment knobs 12
Chapter thumbnail screen 62
CIFS file operations 84
Clip 69
continuous playback mode 52
copying 56
deleting 68
information 17
locking (write-protecting) 68
properties 61
searching with thumbnails 66
selecting 66
setting clip flags 67
setting the index picture frame 69
single clip playback mode 52
Clip F Menu 64
Clip list screens 59
chapter thumbnail screen 62
details view 60
expanded thumbnail screen 62
thumbnails view 60
Clip Menu 64
Clip Properties screen 61
Closed caption data 129
Command list 80
Communication speed and protocol
settings 110
COMPOSITE OUTPUT 1, 2 (SUPER)
connectors 21
Connections 27
cut editing system 28
editing control unit settings 29
for pool coverage 32
FTP connection 27
using the editing function of
recorder 31
Copying 56
Current EDL 70
D
DC IN 12V connector 21
DIGITAL AUDIO (AES/EBU)
IN 1/2, 3/4 connectors 22
OUT 1/2, 3/4 connectors 22
Digital audio signal input/output
section 22
Digital hours meter 112
display modes 112
displaying 113
exiting 113
Disc control section 11
Disc exchange cache
function 50
DISC IN indicator 11
Disc slot 11
Disc status indicator 16
Discs
finalizing 73
formatting 43
handling 43
information 73
loading/unloading 43
reconstructing 51
usable discs 42
write-protecting 43
Display 13, 15
basic operation screen 15
clip list screens 59
switching 59
video monitor screen 18
DISPLAY button 13
Display/menu control section 13
E
Editing
control unit 28
controller 30
EDL 69
EDL 69
creating and editing 70
previewing 70
EJECT button 11
Error messages 121
Essence mark
setting 49, 53
Expand
function 7
Expanded thumbnail screen 62
Extended menu 85
items 92
External storage 45
External synchronization 33
F
Features 6
File operations 75
Clip directory 76
directory structure 75
Edit directory 77
General directory 77
root directory 76
Sub directory 77
UserData directory 78
FOLDER SEL button 12
Front panel 10, 26
changing the angle 26
pulling out 26
returning to original position 26
FTP file operations 79
command list 80
logging in 79
logging out 80
making connections 79
preparations 79
Function buttons (F1 to F6) 13
Function menu 15, 39
HOME page 39
P1 INPUT page 40
P2 INPUT page 40
P3 AUDIO page 41
P4 TC page 41
G
Gigabit Ethernet 7
132 Index
Index
H
Handle 10
HDMI OUT connector 20
HDSDI
remote control function 49
HDSDI OUTPUT 1, 2 (SUPER)
connectors 20
HOME button 14
I
IN
button 12
indicator 12
Initial Setup 25
J
Jog
mode 53
Jog dial 13
Jog/shuttle transport indicators 13
K
KEY INHI switch 11
L
LEVEL adjustment knob 11
Loading/unloading disc 43
M
Maintenance
periodic 112
MAINTENANCE connector 21
Maintenance menu 104
items 104
network settings 109
operations 108
MARK1/MARK2 buttons 12
MEDIA SEL button 12
Menu
bank setting 89
changing settings 90
Clip F Menu 64
Clip Menu 64
configuration 85
function menu 39
maintenance menu 104
returning to default settings 91
setup menu 85
MENU button 13
Metadata 126
Microphone settings 22
N
Names and functions of parts 10
Network
assigning IP address automatically
109
setting IP address 109
settings 109
Network connector 21
NEXT button 14
Normal speed playback 53
O
On/standby button and indicator 10
OUT
button 12
indicator 12
P
PAGE button 14
PHONES jack 11
PLAY button 14
Playback 52
EDL 70
jog mode 53
normal speed 53
settings 52
shot mark settings 53
shuttle mode 54
start position 52
variable mode 54
Playback condition
display 38
mark 37
Power supply section 21
POWER switch 21
Preparation
Initial Setup 25
PREV button 14
Professional Discs 42
Proxy AV data 7
PUSH SET knob 13
R
Rear Panel 20
REC button 14
REC INHI indicator 14
Rec Start essence mark thumbnail
screen 63
Recording 48
HDSDI remote control function
49
level adjustment 49
salvage 50
settings 48
shot mark settings 49
Recording and playback control
section 14
Recording/playback format 17
REF.VIDEO INPUT connectors 21
Reference signal 16
REMOTE (9P) connector 20
REMOTE connector 21
Remote control switch 11
RESET/RETURN button 13
Returning to factory default settings
91
S
Salvage
function 50
SD/HDSDI INPUT connector 20
SDSDI OUTPUT 1, 2 (SUPER)
connectors 20
Setup menu
basic menu 86
extended menu 92
SHIFT button 13
SHTL/JOG button 12
Shuttle
mode 54
Shuttle dial 13
Shuttle/jog/variable control section 12
Specifications 122
STANDBY indicator 14
Status display area 18
Status indicator 17
STOP button 14
Sub clip 69
Superimposed text information 36
Supplying power 23
AC power supply 23
Battery power supply 23
DC power supply 23
SxS memory cards 44
write-protect switch 44
Synchronization reference signals 33
System frequency setting 34
System information 16
T
Text information 36
THUMBNAIL button 13
Thumbnail search 66
chapter thumbnail screen 66
expanded thumbnail screen 66
Tilt mechanism 26
TIME CODE
IN connector 22
OUT connector 22
Time data display area 17
Timecode 34
133
Index
Index
after setting initial value 34
recording external timecode
directly 36
recording sequentially upon the
last recorded timecode
35
recording with the internal
timecode generator
synchronized 35
setting to current time 35
Timecode input/output section 22
Troubleshooting 114
U
UMID Data 126
USB connector 11, 21
USB DRV OFF button 11
User bits
setting 35
V
VAR/JOG button 12
Variable
mode 54
VARIABLE switch 12
Video input indicator 16
W
Write-protecting discs 43
The material contained in this manual consists of information
that is the property of Sony Corporation and is intended solely
for use by the purchasers of the equipment described in this
manual.
Sony Corporation expressly prohibits the duplication of any
portion of this manual or the use thereof for any purpose
other than the operation or maintenance of the equipment
described in this manual without the express written
permission of Sony Corporation.
Sony Corporation
PDW-HD1550
(SYL)
4-542-273-17 (1) © 2014