Sony SNC-WR602C User Manual

Displayed below is the user manual for SNC-WR602C by Sony which is a product in the Security Cameras category. This manual has pages.

Related Manuals

Sony Sony Stativ VCT-SGR1 Manual

Sony Sony Bravia 85" X85K Manual

Sony MDR-E11LP Manual

Sony VPL-FX30 Manual

Sony VPL-FX35 Manual

Sony CLM-V55 Manual

Sony MDR-ZX100 Manual

Sony KDL-46EX720BAEP Manual

Network Camera

User’s Guide

Software Version 3.0

Before operating the unit, please read this manual thoroughly

and retain it for future reference.

SNC-WR630/WR632/WR632C/WR600/WR602/WR602C

A-EMG-100-17(1)

2Table of Contents

Table of Contents

Overview

Features .................................................................. 4

How to Use This User’s Guide .............................. 5

System Requirements ............................................ 5

Accessing the Camera Using the Web

Browser ................................................................... 6

Basic Configuration by the Administrator ......... 8

Precautions for Preventing Access to the Camera

by an Unintended Third Party ............................. 9

How to set up ..................................................... 9

Operating the Camera

Administrator and User ...................................... 10

Logging in to System ........................................... 11

Logging in as a user ......................................... 11

About Viewers .................................................. 11

Configuration of Live Viewer ............................. 12

Main menu ....................................................... 12

Control panel section ....................................... 12

Monitor image .................................................. 14

Plug-in free viewer ........................................... 14

Operating the Camera ........................................ 15

Controlling via the control panel (Operation

common to Area zoom mode and Vector

dragging mode) .............................................. 15

Panning and tilting by clicking the monitor image

(Area zoom mode only) ................................. 16

Panning, tilting and zooming by specifying the

area (Area zoom mode only) .......................... 16

Panning and tilting by dragging the screen (Vector

dragging mode only) ...................................... 16

Moving the camera to a preset position (Common

operations in Area zoom and Vector dragging

modes) ............................................................ 17

Using pan/tilt/zoom operations with the displayed

control bar (PTZ Control bar only) ................ 17

Controlling the Camera on a Panorama

Image .................................................................... 17

Facing the camera toward a specified point ..... 17

Switching Transmission Mode ........................... 18

Playback viewer ................................................... 19

Control panel section ....................................... 19

Monitor image .................................................. 20

Administrating the Camera

Basic Operations of the Administrator Menu ...21

How to set up the Administrator menu .............21

Configuration of the Administrator menu ........21

Configuring the System — System Menu ..........22

Information Tab ................................................22

Date & time Tab ................................................22

Installation Tab .................................................23

Initialize Tab .....................................................24

System log Tab .................................................25

Access log Tab ..................................................25

Service Tab .......................................................25

Setting the Camera Image and Audio

— Video / Audio Menu ........................................26

Picture Tab ........................................................26

Video codec Tab ...............................................28

Audio Tab .........................................................29

Superimpose Tab ..............................................30

Day/Night Tab ..................................................31

Privacy masking Tab .........................................32

Streaming Tab ...................................................34

Configuring the Network — Network Menu .....36

Network Tab .....................................................36

QoS Tab ............................................................37

UPnP Tab ..........................................................38

Setting the Security — Security Menu ...............39

User Tab ............................................................39

Access limit Tab ...............................................40

SSL Tab ............................................................40

How to install the CA certificate ......................43

To remove an installed CA certificate ..............44

To import the personal certificate .....................45

802.1X Tab .......................................................45

System configuration of 802.1X network ........46

Referrer check tab .............................................47

Setting the PTZF control — PTZF control

Menu .....................................................................48

PTZF control Tab ..............................................48

Preset position Tab — Saving pan/tilt/zoom

position ...........................................................49

Preset tour Tab — Setting a preset tour ............50

Serial Tab ..........................................................50

Setting the Sensor input/Camera tampering

detection/Motion detection — Action input

Menu .....................................................................51

Event condition Tab ..........................................51

Sensor input Tab — Set the sensor input

1/2/3/4 .............................................................52

Camera tampering detection Tab — Set the

camera tampering detection ............................52

Motion detection Tab — Set the motion/VMF

detection ..........................................................52

Table of Contents 3

What is VMF .................................................... 52

Setting items for motion detection ................... 53

VMF settings .................................................... 55

Face detection Tab — Set the face detection .... 57

Network disconnection Tab

— Monitoring the connection of a specified IP

address ............................................................ 58

Setting the Action output — Action output

Menu ..................................................................... 59

Execution Condition Tab .................................. 59

Mail Transfer Tab — Setting the e-Mail (SMTP)

Function .......................................................... 59

Alarm output Tab — Setting the Alarm

output .............................................................. 61

Edge Storage Tab — Setting the Edge Storage

movie and still image function ....................... 62

Voice alert Tab .................................................. 63

HTTP alarm notification Tab ........................... 64

FTP still image sending Tab ............................. 65

Setting the Schedule — Schedule Menu ............ 67

Schedule Tab .................................................... 67

Others

Glossary ................................................................ 68

Index ..................................................................... 70

Overview

Features

Overview

Features

• High-quality Full HD (1080P) real-time monitoring,

up to 60 fps. (SNC-WR630/WR632)

• High-quality HD (1280 × 720) live images from

camera can be monitored at a maximum frame rate of

60 fps. (SNC-WR600/WR602)

• Exmor CMOS sensor enables high-quality images for

streaming.

• Wide dynamic range (View-DR) and Visibility

Enhancer enable clearer images for streaming in the

high contrast environment.

• NR (XDNR) enables clearer images for streaming in

the low lightness environment.

• Two video compression modes (video codecs) JPEG/

H.264 are supported.

• The maximum triple codec mode is available.

• “Edge Storage” for recording of video or audio signal

based on alarm detection (such as network block), and

same protocol real-time image streaming.

• Motion detection and camera tampering detection

functions.

• Up to 20 users can view images from one camera at

the same time.

• Date/time can be superimposed on the image.

• IEEE802.3at standard of HPoE (High Power over

Ethernet) compliant. (SNC-WR630/WR600)

• HPoE+ 4 line power-supply compliant. (SNC-WR632/

WR602)

• A high-speed pan/tilt mechanism maximum 700°

rotation/second is equipped. This allows 360° panning

and 220° tilting operability.

• Optical zoom of 30× and digital zoom of 12× high-

magnification zoom functions are provided.

• Quick release function for easier installation or

maintenance is provided.

NOTICE TO USERS

manual or the software described herein, in whole or in

part, may not be reproduced, translated or reduced to

any machine readable form without prior written

approval from Sony Corporation.

SONY CORPORATION PROVIDES NO

WARRANTY WITH REGARD TO THIS MANUAL,

THE SOFTWARE OR OTHER INFORMATION

CONTAINED HEREIN AND HEREBY EXPRESSLY

DISCLAIMS ANY IMPLIED WARRANTIES OF

MERCHANTABILITY OR FITNESS FOR ANY

PARTICULAR PURPOSE WITH REGARD TO THIS

MANUAL, THE SOFTWARE OR SUCH OTHER

INFORMATION. IN NO EVENT SHALL SONY

CORPORATION BE LIABLE FOR ANY

INCIDENTAL, CONSEQUENTIAL OR SPECIAL

DAMAGES, WHETHER BASED ON TORT,

CONTRACT, OR OTHERWISE, ARISING OUT OF

OR IN CONNECTION WITH THIS MANUAL, THE

SOFTWARE OR OTHER INFORMATION

CONTAINED HEREIN OR THE USE THEREOF.

Sony Corporation reserves the right to make any

modification to this manual or the information

contained herein at any time without notice.

The software described herein may also be governed by

the terms of a separate user license agreement.

• is trademark of Sony Corporation.

• “Exmor” and are trademarks of Sony

Corporation.

• Microsoft, Windows, Internet Explorer and

Microsoft DirectX are registered trademarks of

Microsoft Corporation in the United States and/or

other countries.

• Java Script is a trademark of Sun Microsystems, Inc.

in the United States and other countries.

• Intel Core is a registered trademark of Intel

Corporation or its subsidiaries in the United States

and other countries.

• Adobe, Adobe Reader and Adobe Flash are

trademarks of Adobe Systems Incorporated in the

United States and/or other countries.

• SD and micorSD are trademarks of SD-3C and LLC,

registered in the United States and other countries.

All other company and product names are trademarks

or registered trademarks of the respective companies or

their respective makers.

Overview

How to Use This User’s Guide / System Requirements 5

How to Use This User’s

Guide

This User’s Guide explains how to operate the Network

Camera from a computer.

The User’s Guide is designed to be read on the computer

display.

This section gives tips on making the most of the User’s

Guide. Read it before you operate the camera.

Jumping to a related page

When you read the User’s Guide on the computer

display, you can click on a sentence to jump to a related

page.

Software display examples

Note that the displays shown in the User’s Guide are

explanatory examples. Some displays may be different

from the ones that appear in actual use.

The illustrations of the camera and menu display in the

User’s Guide show the SNC-WR630 as an example.

Printing the User’s Guide

Depending on your system, certain displays or

illustrations in the User’s Guide, when printed out, may

differ from those that appear on your screen.

Installation Manual (printed matter)

The supplied Installation Manual describes the names

and functions of parts and controls of the Network

Camera, connection examples, and how to set up the

camera. Be sure to read the Installation Manual before

hand.

Model names

The models below are omitted in this document as their

functions are equal to the relevant models.

• SNC-WR632C is described as SNC-WR632 on the

following pages.

• SNC-WR602C is described as SNC-WR602 on the

following pages.

System Requirements

The following computer environment is necessary for

the computer to display images and the controls of the

camera.

(August 2017)

Common

Microsoft Windows 7 (32-bit version, 64-bit version),

Windows 8.1 Pro (32-bit version, 64-bit version),

Windows 10 Pro (32-bit version, 64-bit version)*

Authorized editions:

Windows 7: Ultimate, Professional

Windows 8.1: Pro

Windows 10: Pro

Microsoft DirectX 9.0c or higher

Web Browser

Windows Internet Explorer Ver.11.0**

Firefox Ver. 54.0

Google Chrome Ver. 60.0

CPU

Intel Core i7, 2.8 GHz or higher

Memory

2 GB or more

Display

1600 × 1200 pixels or higher

* If you are on Windows 10, turn off tablet mode.

** If you are on Windows 8.1, use the Internet Explorer

desktop user interface (desktop UI) edition.

Overview

Accessing the Camera Using the Web Browser

Accessing the Camera

Using the Web Browser

After the IP address has been assigned to the camera,

check that you can actually access the camera using the

Web browser installed on your computer.

Start the Web browser on the computer and type the

IP address of the camera in the URL address bar.

The live viewer window is displayed.

Display sample

Note

The maximum of users on the network who can see a

viewer concurrently is 20. However, if the transmission

ability of the camera is overloaded, access to the camera

may not be possible, even if there are fewer than 20

users.

If monitoring with sound, the maximum number of users

is 10.

Using the SSL function

Note

The model on sale in China does not support the SSL

function.

When Internet Explorer is used

When you enter the camera IP address, “Certificate

Error” may appear according to the status of the

certificate set on the camera. In this case, click Continue

to this website (not recommended). to continue.

The live viewer window appears (in SSL

communication).

When “Allow HTTP connection for some

clients” (page 41) is checked

To use HTTP and SSL connections separately to access,

enter the following in the address box of the browser.

For HTTP connection

http://192.168.0.100/index.html?lang=en

For SSL connection

https://192.168.0.100/index.html?lang=en

When the live viewer of the camera is

displayed for the first time

“Security Warning” is displayed. When you click Ye s ,

ActiveX control is installed and the live viewer is

displayed.

Notes

• If Automatic configuration is enabled in the Local

Area Network (LAN) settings of Internet Explorer, the

image may not be displayed. In that case, disable

Automatic configuration and set the proxy server

manually. For the setting of the proxy server, consult

your network administrator.

• When you install ActiveX Control, you should be

logged in to the computer as Administrator.

Overview

Accessing the Camera Using the Web Browser 7

Tips

• The software is optimized for Internet Explorer using

medium font.

• In case a part of the image cannot fit the display,

configure the display setting (magnification

percentage) to 100%.

If you use a display with high pixel density, the

magnification percentage may be changed

automatically.

To display the viewer correctly

To operate the viewer correctly, set the security level of

Internet Explorer to Medium or lower, as follows:

Select Tools from the menu bar for Internet

Explorer, then select Internet Options and click

the Security tab.

Click the Internet icon (when using the camera via

the Internet), or Local intranet icon (when using

the camera via a local network).

Set the slider to Medium or lower. (If the slider is

not displayed, click Default Level.)

When using antivirus software, etc., on

the computer

• When you use antivirus software, security software,

personal firewall or pop-up blocker on your computer,

the camera performance may be reduced, for example,

the frame rate for displaying the image may be lower.

• The Web page displayed when you log in to the

camera uses JavaScript. The display of the Web page

may be affected if you use antivirus software or other

software described above on your computer.

Overview

Basic Configuration by the Administrator

Basic Configuration by

the Administrator

You can monitor the camera image by logging in with

the initial conditions set for this network camera. You

can also set various functions according to the installing

position, network conditions or purpose of the camera.

We recommend you configure the following items

before monitoring images from the camera.

Setting contents Setting menu

Set the format of the image sent from the camera. Video codec Tab (page 28)

Select the White balance mode according to the installation position. White balance (page 27)

Select the brightness of the image sent from the camera. Exposure (page 26)

Brightness (page 27)

Select the quality of the image sent from the camera. Video codec Tab (page 28)

Select the view size of the image. View size (page 12)

Select whether the audio from the external input is sent or not. Audio Tab (page 29)

Synchronize the date and time of the camera with those of the computer. Date & time Tab (page 22)

Make the setting for sending the monitor image attached to an e-mail. Mail Transfer Tab (page 59)

Set the user access right for the camera. User Tab (page 39)

Set a place to be watched beforehand. Preset position Tab (page 49)

Overview

Precautions for Preventing Access to the Camera by an Unintended Third Party 9

Precautions for

Preventing Access to

the Camera by an

Unintended Third Party

The camera may be accessed by an unintended third

party on the network, depending on the usage

environment. Changing the user name and password of

the camera administrator from the default settings is

highly recommended for security reasons. If the camera

is accessed by an unintended third party, there may be an

undesired effect, such as operations or settings to block

monitoring, etc.

The camera can be fraudulently accessed in a network

environment where a device is connected or connectable

to the network without the administrator's permission, or

a PC or other network device connected to the network

can be used without any permission. Connect to these

environments at your own risk. To prevent unauthorized

access to the camera, set it according to the following

steps.

Do not use the browser you use to set the camera to

access other websites while you set or after setting the

camera. You will remain logged in to the camera as long

as the browser is open, so to prevent an unintended third

party's use or execution of malicious programs, close the

browser after you finish setting the camera.

How to set up

Set the network address of the camera using SNC

toolbox.

For details about how to use SNC toolbox, refer to

the application guide.

After this step, do not use SNC toolbox to change

the network settings of the camera. Use SNC

toolbox to search for the camera only.

Start the web browser and set the SSL function to

Enable in the camera settings.

For details, refer to “Setting the Security — SSL tab

on the Security menu” in the Administrator menu

on page 40.

Restart the web browser and access the camera

again.

Set the user name and password of the

administrator of the camera.

For details, refer to “Setting the Security — User

tab on the Security menu” in the Administrator

menu on page 39.

Check the Referrer check checkbox.

For details, refer to “Setting the Security —

Referrer check tab on the Security menu” in the

Administrator menu on page 47.

Check the Viewer authentication box.

For details, refer to “Setting the Security — User

tab on the Security menu” in the Administrator

menu on page 39.

Hereafter, use the camera using the SSL connection. If

you use the FTP still image sending function, the SSL

function will be disabled, and communication content

will not be coded. Do not use the FTP still image

sending function if the camera is at risk of unauthorized

access.

Note

The model on sale in China does not support the SSL

function.

Operating the Camera

Administrator and User

Operating the Camera

This section explains how to monitor the image from the

camera using your Web browser.

The functions of the camera should be set by the

Administrator. For the setting of the camera, see

“Administrating the Camera” on page 21.

Administrator and User

This network camera identifies those who log in as the

Administrator or User.

The Administrator can use all the functions of this

network camera, including camera settings. The User

can use the functions for monitoring the image and

audio from the camera, and control the camera. The

Viewer mode setting is used to restrict the user’s access

rights. There are five types of users.

Each type of user can use the corresponding functions below.

zUsable function

– Not usable function

The access rights of the administrator and the user can

be set in “Setting the Security — Security Menu” of the

Administrator menu on page 39.

Function Administrator User

Full Pan/Tilt Light View

Monitor a live image zzzzz

View the date and time zzzzz

Control the frame rate (JPEG mode only) zz–––

Control the image view size zzzz–

Save a still image and movie in the computer zzzz–

Switch the TCP/UDP transmission mode (Available in

H.264 mode only) zz–––

Perform the pan/tilt/zoom operation zzz––

Receive audio zzzzz

Select the codec mode zzzz–

Control the setting menu z––––

Play the recorded file in the memory card zz–––

Delete the recorded file in the memory card z––––

Operating the Camera

Logging in to System 11

Logging in to System

Logging in as a user

Start the Web browser on your computer and type

the IP address of the camera you want to monitor.

The live viewer is displayed.

Display sample:

Note

If the live viewer does not start correctly, the security

level of the Internet Explorer may be set to higher than

Medium. See “To display the viewer correctly” on

page 7 and check the security level.

About Viewers

You can use the following viewers.

ActiveX viewer

This viewer can monitor the camera image in any of the

JPEG and H.264 video codecs. Two types of ActiveX

viewer are available: Live viewer and Playback viewer.

You must install this viewer when you access the viewer

for the first time.

When you display the viewer of the camera for

the first time

When you access the network camera using ActiveX

viewer for the first time, the Security Warning appears.

Click Ye s and install ActiveX Control. You can use all

the functions of the viewer with ActiveX Control.

Plug-in free viewer

This viewer enables a browser other than Internet

Explorer to display images.

Notes

• If Automatic configuration is enabled in the Local

Area Network (LAN) Settings of Internet Explorer,

the camera image may not be displayed. In that case,

disable Automatic configuration and set the proxy

server manually. For the setting of the proxy server,

consult your network administrator.

• When you install ActiveX Control, you should be

logged in to the computer as the Administrator.

Tips

• Every page of this software is optimized for Internet

Explorer in Medium font.

• In case a part of the image cannot fit the display,

configure the display setting (magnification

percentage) to 100%.

If you use a display with high pixel density, the

magnification percentage may be changed

automatically.

Operating the Camera

Configuration of Live Viewer

Configuration of Live

Viewer

This section explains the functions of the parts and

controls of the live viewer. For a detailed explanation on

each part or control, see the specified pages.

Live viewer using ActiveX viewer

Main menu

Live viewer

Displays the ActiveX viewer or the Plug-in free viewer.

Playback viewer

Click to play, save and delete the recorded movie in the

memory card. (page 19)

Setting

Click to display the Administrator menu. (page 21)

You can operate this function only when logging in as

the administrator.

License notice

Displays the software consent agreement, etc.

Language

Set language from pull-down.

Control panel section

You can drag the panels to the monitor screen and

configure them.

To return to the operation panel, drag the panel and

configure the operation panel.

Click the to hide the detail setting menu or click it

again to show the menu.

Information panel

Check the date and time here.

View panel

You can change the screen mode, view size of the image,

image codec mode and frame rate. Also, still images and

movies can be saved (movie saving can also be stopped)

from here. Microphone and audio output levels can be

adjusted.

Screen mode

Select Window or Full Screen.

View size

Selects the view size to be displayed.

Click View size list box to select the view size.

Select ×1/4 to display images, reduced to 1/4 of the size

set in Image size.

Select ×1/2 to display images, reduced to 1/2 of the size

set in Image size.

Select ×1 to display images set in Image size (page 28)

of the Video / Audio menu.

Select Full to display images according to the view size.

Select Fit to display images according to the view size,

with fixed aspect ratio.

Image codec

Select Image1, Image2 and Image3 of the video codec.

Frame rate

(Displayed only when the camera image is in JPEG.)

Selects the frame rate to transmit images.

Control panel section Monitor image section

Main menu

Operating the Camera

Configuration of Live Viewer 13

Capture

Click to capture a still image shot by the camera and to

store it in the computer. Click to open the folder to be

saved.

Note

When protection mode (Windows > Control panel >

Internet options > Security property) is enabled, still

images cannot be captured.

Run/ Stop Save Video

Runs and stops Save Video. Click to open the folder

to be saved.

Note

When protection mode (Windows > Control panel >

Internet options > Security property) is enabled, videos

cannot be saved.

Volume

Displays when Enable in the Audio tab of the Video /

Audio menu is checked.

Use the slide bar to adjust the volume for sound output

level.

When you click , the icon changes to and the

output from the speaker stops. To output sound from the

speaker, click again.

Mic volume

Displays when Audio upload (page 29) in the Audio tab

of the Video / Audio menu is set to Enable, and a user

with audio enabled in the User tab of the Security menu

accesses the device.

Use the slide bar to adjust the microphone volume.

When you click , the icon changes to and the

microphone input stops. To input the microphone, click

again.

Camera control panel

This panel allows you to control the camera’s pan/tilt/

home position and zoom (page 15).

Image action

Select the mode of operation from Off, Area zoom and

Vector dragging.

Pan/Tilt control

Click the arrow button the direction in which you want

to move the camera. Keep it pressed to move the camera

continuously.

To return to the home position, click .

Zoom control

Press to zoom out, and press to zoom in.

Zooming continues while the button remains pressed.

Focus control

To control the focus manually, set Focus mode of the

PTZF control menu to Manual (page 49).

To focus on a nearby object, press . To focus on a

distant object, press .

By pressing , focus is set to the optimum

position.

Panorama panel

Map view and Arctic view are displayed.

You can switch the display. Click to display Map

view and to display Arctic view.

Preset position panel

Displays only when one or more preset positions are

stored in memory.

The registered preset position is displayed.

Operating the Camera

Configuration of Live Viewer

If you select a thumbnail when registering a preset

position, it will be displayed with a thumbnail.

Select the Preset position name from the list. The camera

will move to the preset position that you have stored in

memory using the Preset position menu.

Other panel

The Other panel is displayed in the case of an H.264

image.

You can switch between TCP and UDP (Unicast/

Multicast).

Each click switches the transmission mode of the video/

audio data between TCP mode, Unicast mode, and

Multicast mode (page 18).

Monitor image

The image shot by the camera is shown here.

There are two modes for on-screen pan/tilt/zoom

operation using a mouse: Area zoom mode and Vector

dragging mode.

In the Area zoom mode, click to adjust the camera

direction to the center of the image.

The Area zoom will move the camera in the direction

that displays the area selected by the operator and zooms

in at the same time. The operator can choose a part of the

image to view and zoom in by surrounding an area with

a frame by dragging the mouse.

In the Vector dragging mode, the camera moves to the

dragged direction. How long you drag the mouse

determines the speed. Releasing the button on the mouse

after dragging stops the panning or tilting of the camera.

You can also use the camera control panel bar to change

the camera direction.

The zoom operation using the mouse wheel is available

in all modes.

Plug-in free viewer

Live viewer using Plug-in free viewer

Display sample:

Monitor screen

There are two modes for on-screen pan/tilt/zoom

operation using a mouse: Area zoom mode and Vector

dragging mode. A control bar is displayed on the screen.

In the Area zoom mode, click to adjust the camera

direction to the center of the image.

The Area zoom will move the camera in the direction

that displays the area selected by the operator and zooms

in at the same time. The operator can choose a part of the

image to view and zoom in by surrounding the area with

a frame by dragging the mouse.

In the Vector dragging mode, the camera moves to the

dragged direction. How long you drag the mouse

determines the speed. Releasing the button on the mouse

after dragging stops the panning or tilting of the camera.

You can also use the tool bar to change the camera

direction.

The zoom operation using the mouse wheel is available

in all modes.

Monitor screen

Control bar

Operating the Camera

Operating the Camera 15

Control bar

The following operation buttons are available. Operating the Camera

There are three modes of camera operation: Area zoom

mode, Vector dragging mode and PTZ Control bar.

You can control pan/tilt, zoom and focus in either mode.

The available functions for the camera operation modes

vary according to the live viewer display. The available

functions are as follows:

Controlling via the control panel

(Operation common to Area zoom

mode and Vector dragging mode)

You can operate the camera direction, zoom, and focus

by using the control panel for the monitor image

currently displayed.

Pan/Tilt control

Click the arrow button in the direction in which you

want to move the camera. Keep it pressed to move the

camera continuously.

To return to the home position, click .

Note

When Auto flip set to On (page 48), if you hold ,

or to make the direction of the camera pass through

the point where it faces the ground, the auto flip function

is activated, and the displayed picture is reversed.

Setting

You can set the streaming method, image size,

frame rate, PTZ operation mode and image codec.

Streaming stop button

Stops streaming. (Appears while streaming.)

Streaming start button

Starts streaming. (Appears while stops streaming.)

Save still image button

Captures still images taken by the camera and saves

them to the computer.

Preset

Select a preset position to move the camera to the

registered preset position.

(Displayed only when a camera preset position is

registered.)

ActiveX

viewer

Plug-in free viewer

JPEG JPEG/

Flash ActiveX

Operation from

control panel a×××

Area zoom aaaa

Vector dragging aaaa

PTZ control bar ×aa×

Operating the Camera

Zoom control

Click to zoom out, and click to zoom in.

Zooming continues while the button remains pressed.

Note

The four edges of the image may be dark depending on

the zoom position. This is a phenomenon related to the

structure of the camera, and does not cause a problem.

Focus control

To control the focus manually, set Focus mode of the

PTZF control menu to Manual (page 49).

To focus on a nearby object, click . To focus on a

distant object, click .

By clicking , the focus is set to the

optimum position.

Panning and tilting by clicking the

monitor image (Area zoom mode

only)

Click on the monitor image, and the camera moves so

that the clicked portion is positioned at the center of the

display.

Panning, tilting and zooming by

specifying the area (Area zoom

mode only)

Click and hold the left button of the mouse on the

monitor image, and drag the mouse diagonally to draw a

red frame around the portion you want to enlarge. The

camera moves so that framed portion is positioned at the

center of the display and is zoomed in.

Notes

• When Zoom mode in the PTZF control menu is set to

Full, zooming of the specified area stops at the T end

of the optical zoom. If you want to zoom in further

using the digital zoom, specify the area again.

• When the specified area is zoomed in, the center may

be shifted or some portion of the image may appear

out of the monitor image section. In this case, click the

point you want to move to the center or click the arrow

button on the camera control panel.

Panning and tilting by dragging the

screen (Vector dragging mode

only)

When you click on the starting point on the image and

drag to the end point, the camera pans/tilts in the

direction of the arrow from the starting point to the end

point. The speed of operation is determined by the

length of arrow. Releasing the button on the mouse stops

the panning/tilting of the camera.

Indicates the

available area of

optical zoom. Indicates the

available area of

digital zoom.

Operating the Camera

Controlling the Camera on a Panorama Image 17

Moving the camera to a preset

position (Common operations in

Area zoom and Vector dragging

modes)

Select a preset position name from the Preset position

panel. The camera will move to the preset position that

you have stored in memory using the Preset position tab

of the PTZF control menu (page 49).

Using pan/tilt/zoom operations with

the displayed control bar (PTZ

Control bar only)

Pan/Tilt operations

Click the arrow of the direction you wish to move the

camera. Continue clicking on the arrow to keep moving

the direction of the camera.

Zoom operation

Click to zoom out, click to zoom in. The zoom

operation continues while you are clicking on the

button.

Controlling the Camera

on a Panorama Image

In the panorama window, a 360° view around the camera

is displayed as a panorama image. When you click on

the displayed panorama image, the camera faces the

clicked area.

To create a panorama image

Create the panorama image with the SNC toolbox. For

details, refer the user’s guide of SNC toolbox.

Tip

The panorama image is a still picture converted from the

image taken when you were going to create it with SNC

toolbox. When the camera is moved or when the layout

around the camera is changed, you should create the

panorama image again.

Facing the camera toward a

specified point

Create a panorama image with SNC toolbox and

display it.

Two “Panorama Image” display formats are

available: Map view and Arctic view.

You can switch the display. Click to display

Map view and to display Arctic view.

(The Illustration above is a simulated screen image

of the panorama image. The displays may be

different from the ones that appear in actual use.)

Camera

Panorama window

Map View

Arctic View

Operating the Camera

Switching Transmission Mode

Click the point you want to watch in the panorama

window.

The camera is moved to face toward the clicked

point, and the present image at the point is

displayed in the monitor window.

To rotate the panorama image

To rotate the panorama image in accordance with the

camera’s panning direction, set Panorama mode to

Rotate in the PTZF control menu of the Administrator

menu (page 49). The mark on the panorama image

indicates the panning home position.

Note

The panorama image can be rotated only when a 360-

degree panorama image has been created using SNC

toolbox.

Switching Transmission

Mode

You can change the transmission mode for video/audio

data.

This function can be used when the video codec mode is

set to H.264 and the ActiveX viewer in the live viewer is

used.

Note

The function may not operate correctly if you use

personal firewall software or antivirus software on your

computer. In that case, disable the software or select the

TCP mode.

Select TCP, Unicast or Multicast from the

Connection drop-down list in the Other panel.

TCP: This is normally selected.

When TCP is selected, HTTP communication is

adopted for video/audio communications. HTTP is

the protocol used for reading the usual Web page. In

an environment capable of reading Web pages, you

can watch or listen to video/audio by selecting the

TCP port.

Unicast: When Unicast is selected, RTP (Real-

time Transport Protocol) is adopted for video/audio

communications. Since RTP is the protocol for

running video/audio data, the video/audio playback

is smoother than when TCP (HTTP) is selected. If

a firewall is installed between the camera and the

computer, or depending on the network

environment, video/audio may not play back

properly when Unicast is selected. In this case,

select TCP.

Multicast: This protocol is selectable when

Multicast streaming in the Streaming tab of the

Video / Audio menu is set to Enable. When

Multicast is selected as the transmission port, RTP

(Real-time Transport Protocol) and UDP multicast

techniques are adopted for video/audio

transmission. By selecting it, the network

transmission load of the camera can be reduced. If

a router that does not correspond to a multicast or

firewall is installed between the camera and the

computer, video/audio may not play back properly.

In this case, select TCP or Unicast.

Note

When connecting via a proxy server, neither Unicast nor

Multicast can be selected.

Operating the Camera

Playback viewer 19

Playback viewer

You can play, save or delete the movies recorded in the

memory card.

This function is available only in the following users.

• Administrator

•When Viewer mode is set to Full

Control panel section

View panel

You can change the screen mode or view size of the

image.

Screen mode

Select Window or Full Screen.

View size

Select the view size to be displayed.

Click the View size list box to select the view size.

Select ×1/4 to display images, reduced to 1/4 of the size

set in Image size.

Select ×1/2 to display images, reduced to 1/2 of the size

set in Image size.

Select ×1 to display images set in Image size (page 28)

of the Video / Audio menu.

Select Full to display images according to the view size.

Select Fit to display images according to the view size,

with fixed aspect ratio.

Search panel

Specify the search period.

Start

Select the start time for searching.

End

Select the end time for searching.

Maximum search number

You can specify the maximum number of the search

results.

Search for recorded movies in the specified period.

Search results list

Displays the search results from the search panel. You

can select the movie which you want to play, save or

delete.

You can select multiple files for deletion by clicking

those movies while pressing the control key.

Range of the search results displayed in the list

Indicates the list of the total search results that is

currently displayed.

Go to the next search result

Displays the next search results.

Go to the previous search result

Displays the previous search results.

Control panel

section

Monitor image

section

Operating the Camera

Playback viewer

Save recorded movie

Save the selected movie to your computer. Click to

open the folder in which the movie is to be saved.

Delete recorded movie

Delete the selected movie(s).

Note

Only the administrator can delete movies. Deleted

movies cannot be restored.

Control panel (Basic)

You can play, pause, stop, fast forward or jump the

selected movie on the search results list. Also you can

specify the start position for playback.

If you click the button, the control panel (detail) is

displayed.

Control panel (Detail)

You can play, pause, stop, fast forward or jump the

selected movie on the search results list. Also you can

specify the start position for playback, playback time,

save the movie or save the captured still image.

If you click the button, the control panel (basic) is

displayed.

Specify the start position for playback

Move the start position by dragging the slider.

Time

Specify the recorded date and time from which the

movie will start playback.

Previous record

Jump to the previous movie.

Stop button

Click this button to stop a movie playing.

Play button

Play the movie.

Click this button to play the movie at the normal speed

after pressing the fast forward button.

Pause button

Click this button to pause a movie playing.

Fast forward

Click this button to fast forward the moving being

played.

Next record

Jump to the next movie.

Still image capture

Save the capture of a recorded movie as a still image file

to your computer. Click to open the folder in which

the movie is to be saved.

Specify the playback time

Specify the start and end position of the movie by

moving the slider.

You can save the specified time to your computer.

You can also specify the start time to In and end time to

Out.

Save selected part of recorded movie

Save the part of movie which is specified by the

playback time to your computer. Click to open the

folder in which the movie is to be saved.

Monitor image

Play the selected movie from the search results list.

Specify the start position for playback

Specify the playback time

Administrating the Camera

Basic Operations of the Administrator Menu 21

Administrating the Camera

This section explains how to set the functions of the

camera by the Administrator.

For details about monitoring the camera image, see

“Operating the Camera” on page 10.

This section explains the basic operations and each

option of the Administrator menu.

Note on the display of menu options

The setting menus of this unit will clearly display only

the setting options that you can currently select. Grayed

out options cannot be selected.

Only supported functions are displayed.

Basic Operations of the

Administrator Menu

You can use the Administrator menu to set all functions

to suit the user’s needs.

Click Setting in the viewer to display the Administrator

menu.

How to set up the Administrator

For details, see “Logging in as a user” on page 11.

Click Setting on the main menu.

The authentication dialog appears. Enter the user

name and password for Administrator. The

Administrator menu appears.

The user name “admin” and password “admin” are

set at the factory for the Administrator.

For security, be sure to change the password from

the factory setting before using the camera.

Create a user name and password using half-width

characters that do not include “, (comma)”, “#”,

“&”, “:” or “(space)”.

Click the menu name (example: System) on the left

side of the Administrator menu.

The clicked menu appears.

Example: “System” menu

Select the required tab above the menu, and set each

setting option in the tab.

Example: “Date & time” tab of “System” menu

See page 22 for details of the menu tabs and setting

options.

After setting, click OK.

The settings you have made become active.

Click Cancel to nullify the set values and return to

the previous settings.

Buttons common to every menu

The following buttons are displayed on all the menus.

Click this button to confirm the settings.

Click this button to nullify the set values and return to

the previous settings.

General notes on menus

• Input characters (for usernames, for example) in half-

width characters on a computer. Half-width katakana

cannot be used.

• After changing a setting on a menu, wait at least 30

seconds before turning off the power of the camera.

If the power is turned off immediately, the new setting

may not be stored correctly.

• If the camera settings are changed while watching the

live viewer, some settings cannot be restored. To

reflect the change on the opening live viewer, click

Refresh on the Web browser.

Configuration of the Administrator

System

Displays the System menu. (“Configuring the System —

System Menu” on page 22)

Video / Audio

Displays the Video / Audio menu for setting the camera

image and audio. (“Setting the Camera Image and Audio

— Video / Audio Menu” on page 26)

Administrating the Camera

Configuring the System — System Menu

Network

Displays the Network menu for setting the network

connection. (“Configuring the Network — Network

Menu” on page 36)

Security

Displays the Security menu for setting the login user

name and password to specify which computer(s) can

connect to the camera. (“Setting the Security — Security

Menu” on page 39)

PTZF control

Displays the setting menu for pan, tilt, zoom and focus

control. (“Setting the PTZF control — PTZF control

Menu” on page 48)

Action input

Displays the setting menu for all built-in detection

functions. (“Setting the Sensor input/Camera tampering

detection/Motion detection — Action input Menu” on

page 51)

Action output

Displays the Action output menu for setting an action of

the functions such as e-Mail (SMTP) and Edge Storage.

(“Setting the Action output — Action output Menu” on

page 59)

Schedule

Displays the Schedule menu for the e-Mail (SMTP)

function, Alarm output function, Voice alert function,

etc. (“Setting the Schedule — Schedule Menu” on page

67)

Configuring the System

— System Menu

When you click in the Administrator menu, the

System menu appears.

Use this menu to perform the principal settings of the

software.

The System menu consists of the following tabs:

Information, Date & time, Installation, Initialize,

System log and Access log.

Information Tab

Model Name

The model name of the camera is displayed.

Serial number

The serial number of the camera is displayed.

Software version

The software version of the camera is displayed.

Date & time Tab

Current date & time

Displays the date and time set on the camera.

Note

After you have purchased the camera, be sure to check

the date and time of the camera and set as necessary.

PC clock

Displays the date and time set on your computer.

Date & time format

Select the format of date and time to be displayed in the

viewer from the drop-down list.

System

Administrating the Camera

Configuring the System — System Menu 23

You can select the format between yyyy-mm-dd

hh:mm:ss (year-month-day hour:minutes:seconds),

mm-dd-yyyy hh:mm:ss (month-day-year

hour:minutes:seconds), and dd-mm-yyyy hh:mm:ss

(day-month-year hour:minutes:seconds).

Time setting

Select how to set the day and time.

Keep current setting: Select if you do not need to set

the date and time.

Synchronize with PC: Select if you want to

synchronize the camera’s date and time with the

computer.

Manual setting: Select if you want to set the camera’s

date and time manually.

Select the year, month, date, hour, minutes and

seconds from each drop-down list.

Synchronize with NTP: Select if you want to

synchronize the camera’s date and time with those of

the time server called NTP server (Network Time

Protocol).

Set the NTP server when Synchronize with NTP is

selected.

NTP server

Synchronize with the selected NTP server address.

Time zone

Set the time difference from Greenwich Mean Time in

the area where the camera is installed.

Select the time zone in the area where the camera is

installed from the drop-down list.

Manual time zone

If you select Manual in Time zone, you can set a desired

time zone that is not included in the list box. The input

format is compliant with IEEE 1003.1 section 8.3

standard.

Format:

stdoffset[dst[offset][,start[/time],end[/time]]]

std: 3 to 100 character strings

offset: time difference (displayed in +-)

dst: name of summer time

offset: offset of summer time, default time is 1 hour

start: start date and time of summer time

end: end date and time of summer time

Values in [ ] can be omitted.

For example:

In case of (UTC-06:00) Central Standard Time (USA

and Canada);

CentralStandardTime6DaylightTime1,M3.2.0,M11.1.0

The name of the time zone is CentralStandardTime and

the time difference is 6 hours. The name of the summer

time is DaylightTime, and the summer time offset from

the time difference is 1 hour, starting from the second

week on Sunday in March until the first week on Sunday

in November.

Automatically adjust clock for daylight saving

time changes

When selected, the clock is automatically adjusted

according to the daylight saving time of the selected

time zone.

Note

If the time zone selected in Time zone is different from

that set on the computer, the time is adjusted using the

time zone difference and set on the camera.

OK/Cancel

See “Buttons common to every menu” on page 21.

Installation Tab

You can perform settings related to installation.

Stabilizer

Set the stabilizer function. Select the checkbox to

display steadier images when the camera is installed in

a place subject to vibration.

Notes

• When the stabilizer function is set, the angle of image

taken will be smaller than usual.

• The stabilizer may not respond, depending on the

amount of vibration.

• Be sure to set this function during the installation.

• Set the privacy masking position or the motion

detection area, before setting the stabilizer.

OK/Cancel

See “Buttons common to every menu” on page 21.

Administrating the Camera

Configuring the System — System Menu

Initialize Tab

Reboot

Used when rebooting the system.

Click Reboot, and the message “This System will be

rebooted. Are you sure?” appears. Click OK to reboot

the camera. It takes about two minutes to restart.

Factory default

Resets the camera to the factory settings.

Retain current network settings

When this item is checked, only the current network

settings will be retained after reset.

Click Factory default, and the message “This System

will be rebooted. Are you sure?” appears.

When you click OK, the network indicator on the

camera starts to blink. After adjustments of the default

settings have finished, the camera reboots automatically.

Do not turn off the camera until the camera reboots.

Tip

The camera can also be reset to the factory settings by

turning on the power of this unit while pressing the reset

button on the camera. For details, refer to the supplied

Installation Manual.

Format memory card

You can format a memory card (not supplied) inserted

into the card slot of the camera. When you click Format

memory card, a confirming message appears. Click

OK to start formatting. Any files and folders stored in

the memory card will be deleted.

Notes

• Before formatting, set Edge Storage movie and Edge

Storage still image in the Execution Condition tab of

the Action output menu to Off, to write-protect the

memory card.

• Do not activate the Format memory card function

when no card is inserted into the card slot.

Backup setting data

Saves the setting data of the camera in a file.

Click Save, and follow the instructions on the Web

browser to specify the folder and save the setting data of

the camera.

The file name preset at the factory is “snc-wr630.cfg”

for SNC-WR630.

Restore setting

Loads the stored setting data of the camera.

Click Browse... and select the file in which the setting

data is stored. Click OK, and the camera is adjusted

according to the loaded data.

Restore preset position and privacy masking

settings

If you select this, the stored setting data of the camera,

the preset position data and privacy masking data are

loaded.

Notes

•With Restore setting, some items in the Network

menu (page 36) cannot be restored.

• The following items cannot be stored or restored with

Backup setting data or Restore setting.

– audio files uploaded using the SNC toolbox

– a panorama image recorded in the camera using

Panorama Creator of SNC toolbox

– a certificate to be used in the 802.1X function

– a certificate to be used in the SSL function

– thumbnail

– superimpose logo

Video & PT drive refresh

Image distortion and misalignment of the pan/tilt

position may occur during extended periods of use. Use

this function to correct image distortion and pan/tilt

misalignment. Video & PT drive refresh takes about 20

seconds to complete. Pan/tilt operations for the camera

are performed automatically during the refresh

operation. After refresh is completed, the pan/tilt

position returns to that at the start of the refresh

operation.

Enable

Check to use the refresh operation.

Manual

Click Execute to perform the refresh operation.

Administrating the Camera

Configuring the System — System Menu 25

Schedule

Set time and date to perform the refresh operation

periodically.

Notes

• Camera operation will be canceled when you run

video & PT drive refresh while operating the camera.

• Position/shadow tours stops if video & PT drive

refresh is running while you are running position/

shadow tours.

After video & PT drive refresh has been completed,

the position/shadow tour restarts.

• The intelligent motion detection or camera tampering

detection stops immediately if you execute video &

PT drive refresh when the intelligent motion detection

or camera tampering detection is set.

After video & PT drive refresh is completed, the

motion detection or camera tampering detection

restarts.

Delete panorama image

Click Delete to delete panorama images set on this

camera.

Delete voice alert file

Click Delete to delete all the audio files stored in the

camera.

Notes

•Clicking Delete deletes all the stored audio files

simultaneously. To delete a specified audio file only,

perform deletion of the audio file in the corresponding

Execution Condition tab of the Action output menu

(page 59).

• Before deleting the audio file, set Voice alert to Off in

the Execution Condition tab of the Action output

menu (page 59).

Delete superimpose logo

Click Delete to delete the superimposed logo, specified

by Position in the Superimpose tab of the Video / Audio

menu, from the camera.

To set whether to show or hide the superimpose logo,

you need to configure the setting under the Superimpose

tab.

System log Tab

The data of the software activity of the camera is

recorded in this log. It includes data that is useful if a

problem occurs.

Click Reload to reload the latest data.

Click Log level in the list box to adjust the importance

of information to be recorded in the camera as a system

log. Set the maximum record number to be recorded in

the camera in Log size.

Log information can be saved as a file by clicking

Download of Download as file.

Access log Tab

The access record of the camera is displayed.

Click Reload to reload the latest data.

Click Log level in the list box to adjust the importance

of information to be recorded in the camera as an access

log. Set the maximum record number to be recorded in

the camera in Log size.

Log information can be saved as a file by clicking

Download of Download as file.

Service Tab

Downloads the device information data to use for

service. Select the I agree to download device

information. checkbox and click OK to allow

downloading. Click Download and follow the

instruction on the Web browser to specify the folder to

save the device information of the camera.

File will be saved in binary format data.

Administrating the Camera

Setting the Camera Image and Audio — Video / Audio Menu

Setting the Camera

Image and Audio

— Video / Audio Menu

When you click in the Administrator

menu, the Video / Audio menu appears.

Use this menu to set the functions of the camera.

The Video / Audio menu consists of the Picture, Video

codec, Audio, Superimpose, Day/Night, Privacy

masking and Streaming tabs.

Picture Tab

You can set the color conditions, exposure, etc., of the

camera.

Preview screen

Preview the image and adjust the picture setting.

Picture mode

Select the combination of image quality mode to suit the

camera scene.

You can set the scene to Standard, Situation Priority,

Flickerless.

When the dialog appears, click OK to apply the selected

picture mode. You can change the settings of image

quality individually.

Standard

Set the image quality to suit variable scenes.

Situation Priority

You can set the priority to Moving object or Low noise.

Priority level can also be set.

Moving object: Stabilizes images.

Low noise: Reduces noise on images especially dark

scenes.

Flickerless

Select when you want to reduce the flicker on images.

Set according to power frequency (50 Hz or 60 Hz) of

the lighting you use.

Exposure

Adjust the settings of exposure.

Full auto: The camera performs the gain, iris and

shutter speed adjustments automatically.

Shutter priority: The camera performs the gain and iris

adjustments automatically, and you can select the

shutter speed.

Iris priority: The camera performs the gain and shutter

speed adjustments automatically, and you can select

the iris.

Manual: Adjust the gain, iris and shutter speed

manually.

Wide dynamic range (View-DR)

In high-contrast scenes such as against a back light, this

function reduces overexposure and underexposure.

Select the checkbox to turn on the Wide dynamic range

(View-DR) function.

Visibility Enhancer

Using the Visibility Enhancer function will make the

darker part of a camera image brighter as well as

automatically correct brightness and contrast to show

bright parts clearly without overexposure.

Defog

The defog function improves visibility when there is

fog.

Backlight compensation

Select the checkbox to enable the backlight

compensation function.

Exposure compensation

Select the exposure correction value from the list box to

adjust the target brightness for the automatic exposure

setting. A larger value brightens the image, and a smaller

value darkens the image.

Auto gain Max. value

Limit the maximum value of gain-controlled automatic

exposure control.

Note

The value shown in the auto gain maximum rate is a

standard value, and may differ from the actual one.

Shutter speed

Select the shutter speed from the list box.

When Mode is set to Full auto, select from Fastest

(maximum) and Slowest (minimum).

Note

When Wide dynamic range (View-DR) is selected, the

exposure mode is Full auto and the shutter speed setting

is not reflected.

Iris

Select the iris from the list box.

Gain

Select the gain from the list box.

Video / Audio

Administrating the Camera

Setting the Camera Image and Audio — Video / Audio Menu 27

White balance

Mode

Select the White balance mode.

ATW: Eliminating the influences caused by

environmental illumination or lights, adjust the white

balance automatically to reproduce original colors of

the objects (approximately 2000 K to

10000 K).

ATW-PRO: Automatically adjusts the color to be

closest to the image you are viewing (approximately

2500 K to 6000 K).

Indoor: Sets a white balance suitable for indoor

photography.

Outdoor: Sets a white balance suitable for outdoor

photography.

Fluorescent lamp: Sets a white balance suitable for

photography under three-band fluorescent lighting

with a neutral white color.

Mercury lamp: Sets a white balance suitable for

photography under a mercury lamp.

Sodium vapour lamp: Sets a white balance suitable for

photography under a high-pressure sodium vapor

lamp.

Metal halide lamp: Sets a white balance suitable for

photography under a metal halide lamp.

White LED: Sets a white balance suitable for

photography under the light of white LEDs.

One push WB: The One push trigger button becomes

active. Click On to adjust the white balance instantly.

Manual: When this option is selected, R gain and B

gain become active. Selectable gain values are from

0 to 4095.

Picture

NR (XDNR)

Select the level to reduce image noise. When you select

Off, the NR function is not available.

Brightness

Set the brightness. Select high values to make the image

brighter, lower values to make the image darker.

Saturation

Set the saturation. Select high values to make the image

color stronger, lower values to make the image color

weaker.

Sharpness

Set the sharpness. Select high values to make the image

edges sharper, lower values to make the image edges

smoother.

Video out

Set a signal to output the analog video from the video

output terminal of the camera.

You can select NTSC or PAL.

When the video output mode is changed, the camera

returns to the home position.

Highlight Compensation

Automatically detects highlight areas and masks them.

Mask Level

Mask level from 0 to 15 can be selected.

0: No areas masked.

1: Masks bright areas.

15: Masking from less bright areas.

Notes

• Bright area is not filled by a plain color.

• Masked colors depend on Mask Level and brightness.

Compensation Level

Enhance the video level of dark parts to enhance

visibility.

Change the visibility of dark parts by selecting Low or

High in the Compensation Level.

Off: No effect.

Low: Enhances visibility of dark parts.

High: Further enhances visibility of dark parts. Image

noise of the dark parts may be conspicuous at the

same time.

Notes

• The differences may not be apparent between Low

and High depending on the shooting environment.

• The differences may not be apparent between Low

and High depending on the camera scene.

• The setting of Compensation Level does not affect

the Mask Level.

Tips

• The effect of Highlight Compensation is only to ease

eye strain for operators by masking highlight areas.

• When this function is executed, original white color

could be masked in gray.

• This function depends on high brightness. Highlight

areas can be masked in both Color and Monochrome

mode.

• In case of using View-DR ON, the effect of Highlight

Compensation is lessened because View-DR reduces

brightness of the highlight area.

OK/Cancel

See “Buttons common to every menu” on page 21.

Administrating the Camera

Setting the Camera Image and Audio — Video / Audio Menu

Video codec Tab

Use this tab to set the items for the video codec.

Full HD dual stream mode

Supported models: SNC-WR630/WR632

When you set this On, the highest resolution which can

be set on Image 2 will be 1920 × 1080.

When you set this Off, the highest resolution which can

be set on Image 2 will be 1280 × 720.

Note

When you set this mode On, High framerate mode

cannot be set to On.

High framerate mode

When the setting is set to On, set the maximum frame

rate to 60 fps (NTSC) or 50 fps (PAL).

When the setting is set to Off, the maximum frame rate

is 30 fps (NTSC) or 25 fps (PAL).

When the high framerate mode is changed, the camera

returns to the home position.

Notes

• When the setting is set to On, Image 2 may not be

available, and Image 3 is not available.

• When the high framerate mode setting is changed,

settings for Image 1, Image 2, and Image 3 are

returned to the default settings.

• When you set this On, Full HD dual stream mode

cannot be set to On. (SNC-WR630/WR632)

Image 1, Image 2, and Image 3

Up to three image codec modes can be set. Configure the

following setting for each image mode.

Image codec

Select H.264, JPEG, or Off. Note that Image 1 cannot

be set to Off.

Note

The selectable size of images and frame rate for Image

2 and Image 3 may be limited, depending on the setting

of codec type, image size, frame rate, and image quality

for Image 1.

• The total of frame rate for Image 1, Image 2, and

Image 3 should not exceed 60 fps.

• If you set the bitrate of Image 1 to 32000 kbps, set

Image 2 and Image 3 to Off.

• If you set the bitrate of Image 1 to 16000 kbps or

faster, set the bitrate of Image 2 and Image 3 below

4000 kbps.

If you set a value exceeding the standard, the following

symptoms may occur.

• The image delays more than usual.

• The frame is skipped when playing an image.

• The audio is broken.

• The response of the camera to commands is delayed.

Image size

You can select the size of images sent from the camera.

Notes

• Some parts of the screen may not be displayed

depending on the image size.

• If the image size is 720 × 574 or 720 × 480, the full

image is displayed but not in the 1:1 pixel aspect ratio.

Frame rate

Set the frame rate of the image.

“fps” is a unit indicating the number of frames

transmitted per second.

The frame rate of JPEG image can be changed by the

setting of Image quality.

I-picture interval

Set the I-picture insertion interval.

Select Time to set in seconds.

Select Frame to set in frames.

H.264 profile

Set the profile setting for H.264 video codec to high,

main, or baseline. The video compression efficiency is

high, main, and baseline in sequence. The specified

profile may not be available depending on the program

you use. Select the profile which is suitable for your

program.

Bit rate compression mode

Select CBR, VBR, or Adaptive rate control.

If you want to keep the bit rate fixed, select CBR. If you

want to keep the image quality fixed, select VBR.

If you select Adaptive rate control, the bit rate is

automatically optimized for unstable network

connections or wireless networks with a lot of

interference.

Notes

• The frame rate or bit rate that is actually transmitted

may be different from the set values depending on

image size, scene, network environment.

•The Adaptive rate control cannot operate when the

Plug-in free viewer is being used.

• If you want to use the Adaptive rate control, set the

connection method in the live viewer to Unicast. If

you set TCP as a connection method, the adaptive rate

control will be disabled. For details, refer to

“Switching Transmission Mode” in “Operating the

Camera” on page 18.

Administrating the Camera

Setting the Camera Image and Audio — Video / Audio Menu 29

Bit rate

When you set Image codec to H.264 and set Bit rate

compression mode to CBR, the bit rate of the image

transmission for a line can be set.

When the bit rate is set to a high level, a high image

quality can be enjoyed.

Maximum bit rate limit

Enable the check box when Bit rate compression mode

is set to VBR, to set the maximum value of the bit rate.

Max: Set the maximum value of the bit rate when the

camera is operated with VBR.

Accept frame skip: If you enable the checkbox, the

frame skip will be allowed for bit rate control.

Min, Max

Set the maximum and minimum bit rates that are

adjusted with the adaptive rate mode when Bit rate

compression mode is set to Adaptive rate control.

Image quality

If you set Image codec to JPEG, or Bit rate

compression mode to VBR when Image codec is set to

H.264, the image quality setting will be enabled.

Selectable values are from 1 to 10. When 10 is selected,

the best image quality is achieved.

Bandwidth control

Limits the network bandwidth for the JPEG image data

output from the camera when you set Image codec to

JPEG.

Note

Audio may be interrupted depending on the selected

bandwidth. In this case, select a wider bandwidth. This

function is not available when the setting is set to 0.

OK/Cancel

See “Buttons common to every menu” on page 21.

Audio Tab

Audio sending

Make settings for sending audio from the m

microphone input connector.

Enable

Select the checkbox if you want to send audio from the

network camera.

Note

When you change the Audio setting, click Refresh on

the Web browser to reflect the change on the opening

live viewer page.

Audio in

Select microphone input or line input.

Mic volume

When the Audio in is set to microphone input, set the

volume level of the audio input from the m microphone

input connector. It is adjustable from –10 to +10.

Audio codec

Select the codec type of audio from the m microphone

input connector. The bit rate may differ, depending on

the codec type.

Note

No audio is output if the Plug-in free viewer is used.

Audio upload

You can output audio that is input to your computer’s

audio input terminal from a powered speaker connected

to the line output jack of the camera.

Enable

Select the checkbox to enable the audio upload function.

Volume

Set the speaker volume level from –10 to +10.

OK/Cancel

See “Buttons common to every menu” on page 21.

Administrating the Camera

Setting the Camera Image and Audio — Video / Audio Menu

Superimpose Tab

Select whether or not to superimpose the custom string

and the character date & time on the image.

You can set the superimpose on/off, font sizes, and

display items to display for Image 1, Image 2, and

Image 3 separately in this camera.

Notes

• For setting the superimposing, set Image size1 in the

Video codec tab of the Video / Audio menu to the

maximum rate.

• Deselect the checkbox of Stabilizer in the Installation

tab of the System menu. After setting superimpose, set

the Stabilizer function again.

Preview screen

Preview the image, and adjust the superimposed image.

You can move the position of superimposed image

displayed on the preview screen by drag and drop.

Image

Select the video codec mode to set for the superimposed

image.

The setting for the superimposed image is available if

you select the checkbox next to the list box.

For details about the video codec mode, see the Video

codec tab in the Video / Audio menu.

Position

Select the number of the display position or logo, on the

preview screen. When Logo is selected, the logo file

setting is displayed.

Note

Permissible logo file specifications;

File format: PNG8 with alpha channel

Image size: 640 × 120 or smaller (Image 1, Image 2)

160 × 120 or smaller (Image 3)

Width (pixels): multiples of 16

When display position number 1, 2 or 3 is selected, the

following setting menus appear.

Type

Set the type of display information to Text, Date &

time, Event, Codec, Camera direction, Zoom ratio 1,

and Zoom ratio 2.

Text: Displays the custom string.

Date & time: Displays the date and time.

Event: Displays the event alarm information.

Codec: Displays the video codec information.

Zoom ratio 1: Displays the optical zoom ratio and the

digital zoom ratio.

Zoom ratio 2: Displays the zoom ratio that is multiplied

for the optical zoom ratio and the digital zoom ratio.

Camera direction: Displays the information of camera

direction.

When you set the preset position and/or operate the pan/

tilt/zoom, the display is refreshed. When Camera

direction is selected in Type, the information to be

displayed is Preset, Area title, and Azimuth.

It is enabled when each checkbox is selected.

Click OK to enable the setting.

The display is given priority in order of Preset position,

Area title, Azimuth.

Preset position

Select the Preset position tab to display the preset

positions and names currently set on the setting screen.

The preset name is set in the Preset position tab of the

PTZF control menu.

When you select the preset name from the Preset list and

click the Call button, the camera moves to the set preset

position and the preset name is displayed.

Area title

Select the Area title tab to display the setting menu of

the area title name to be displayed.

In the Area title, an area of camera direction can be set.

When the camera is directed to the set area, the area title

name is displayed.

You can set 64 positions for the area title, and the area

titles are displayed for the numbers that “Enable” is

checked.

Administrating the Camera

Setting the Camera Image and Audio — Video / Audio Menu 31

For example: How to set Area title;

Select the radio button of the area number to be set.

Enter the area name.

Check “Enable” of display.

Operate the pan/tilt/zoom or control the camera

direction clicking the panorama image, and click

Set button of Lower left.

Operate the pan/tilt/zoom or control the camera

direction clicking the panorama image, and click

Set button of Upper right.

Click the Call button to move the camera to the position

of Lower left or Upper right in the set area.

Click the Clear button to clear the position of Lower

left or Upper right. By clearing both Lower left or

Upper right positions, the setting can be cleared.

Azimuth

Select the Azimuth tab to display the setting screen of

azimuth display.

In the Azimuth, the camera direction is displayed as 4

directions or 8 directions.

The direction specified in North direction setting is set

as north, and the azimuth is displayed.

Azimuth mode: Select the azimuth to be displayed from

4 directions or 8 directions.

North direction setting: When you change the camera

direction to due north and click Set, the position is

set as due north. Click Call to change the camera

direction to the set due north.

Custom string

Describes the superimposed content for each position.

For Type setting, codec is displayed as <codecinfo>,

date & time is displayed as <datetime>, event is

displayed as <event>, camera direction is displayed as

<direction>, and you can add a custom string.

Use alphanumeric other than “#”, “&”, “(”, or “$”.

Text color

Select the font color of the superimposed text.

Background color

Select the background color of the superimposed text.

Alignment

Set the horizontal position of the superimposed text.

Transparent

Select the background color transparent of the

superimposed text. When you select Off, transparent is

not available.

Font size

You can select the font size of the superimposed text and

set the font size for Image 1, 2, and 3 separately. If Auto

is selected, the font size is adjusted to suit the image size

of the image number.

Events displayed

Displays in the menu when the type is set to Event.

Select the type of superimpose to be displayed for the

event.

OK/Cancel

See “Buttons common to every menu” on page 21.

Day/Night Tab

Use this tab to set the day/night function of the camera.

Mode

Select the day/night mode. This function has the

following modes.

Auto

Normally works in day mode; switches automatically to

night mode in a dark place.

Threshold

This mode is available when Auto is selected.

Set the brightness level when the day mode is set.

Manual

Switch the day/night mode manually.

When you select Manual and the checkbox of the night

mode is selected, the camera works in night mode.

Otherwise, the camera works in day mode.

Administrating the Camera

Setting the Camera Image and Audio — Video / Audio Menu

Timer

Normally the camera works in day mode. It switches to

night mode at the time you set in Timer of Day/Night in

the Schedule menu.

Sensor input

Controls the day/night mode by synchronizing it with

the sensor input.

Select the synchronized sensor from Sensor input 1,

Sensor input 2, Sensor input 3 and Sensor input 4.

While a sensor input is detected, the camera works in

night mode.

Status

Displays the day/night function status.

Near-IR compensation

Adjust background light when using the IR lamp or

where there is much near short infrared ray. Select the

checkbox to increase the accuracy of auto-focus in night

mode.

OK/Cancel

See “Buttons common to every menu” on page 21.

Privacy masking Tab

Using the privacy masking enables you to hide images

by masking specified parts of the images when

streaming.

Note

Perform the following before setting the privacy

masking.

• Deselect the checkbox of Stabilizer in the Installation

tab of the System menu. After setting the privacy

masking, set the Stabilizer function again.

Preview screen

This screen is for monitoring images and configuring

privacy masking.

You can move the position of the privacy mask displayed

on the preview screen by drag and drop.

Effect

Set the effect of privacy masks.

Color

Specify the color of privacy masks. This setting is

common to every privacy mask.

Position

Select the number corresponding to the display position

on the preview screen.

After completing the configuration, register by clicking

OK.

Clear

Click the button to delete the privacy mask set in

Position.

Do not display mask in wide zoom range

You can switch to display/hide the privacy mask at the

specified zoom position.

When the checkbox is checked, the privacy mask will

not be shown if the zoom position is on the Wide side

rather than the specified zoom position.

Display mask from current position

When you click the Set button, display/hide of the

privacy mask will be switched.

The privacy mask will not be shown if the zoom position

is on the Wide side rather than the specified zoom

position.

Mask range

Click on the bar to set the zoom position at where

display/hide of the privacy is switched.

This can be also set by inputting a number and clicking

the Set by value button.

Clear all

Click the button to delete all privacy mask.

Call

Click the button to move the privacy mask set in

Position to the center of the image.

Administrating the Camera

Setting the Camera Image and Audio — Video / Audio Menu 33

Setting a privacy mask

Operate according to the following procedure to set a

privacy mask in the position of your choice:

Select the number to register from the Position

drop-down list.

Specify the privacy mask area by dragging the

mouse on the preview screen.

Select the effect and color of the mask from the

Effect and Color drop-down list.

Note

The color is common to every privacy mask. The

color selected last is applied.

Click OK.

The mask is displayed on the preview screen.

Notes

• The mask cannot be set on the viewer by clicking OK

if the camera is tilted beyond +65°.

• If you change the direction of the camera, the mask

may not cover the object properly. Ensure the Privacy

masking area is sized sufficiently beforehand.

• The color is common to every privacy mask. The color

selected last is applied.

Set displaying/hiding the privacy mask by

linking with the zoom position

By following the steps below, you can hide the privacy

mask when the zoom position is at the Wide side than

the specified zoom position.

Select the Position of the set privacy mask.

Select the checkbox for Do not display mask in

wide zoom range.

To specify the zoom position, press Set under

Display mask from current position. It can also

be set by clicking the Mask area bar or inputting

numerics and pressing Set by value.

Press Set under Display mask from current position to

set the current zoom position value as the specified

zoom position.

Press Set after adjusting the specified zoom position by

operating the zoom position on the preview screen etc.

A specified zoom position can be set by clicking the

mask area bar.

Also, input the value and press Set by value to set the

specified zoom position in a more accurate way.

Note

The specified zoom position can be set within the optical

zoom area.

Click Set under Display mask from current position,

click the Mask area bar, or Set by value to specify the

zoom position.

Press the OK button to set the privacy mask on the

position where the frame is shown on the preview

screen.

Privacy mask setting range

The setting range of the privacy mask is limited as

follows:

Pan angle:

Tilt angle:

Notes

• The privacy mask area is a rectangle that is specified

with respect to the center of the camera image. The

privacy mask may not be set in areas close to the end

of tilt operation.

• You can set 24 privacy masks. However, only up to

eight privacy masks can be displayed in the screen at

one time. When nine or more privacy masks are set,

masks will be displayed by number in ascending order.

65°

20°

Administrating the Camera

Setting the Camera Image and Audio — Video / Audio Menu

OK/Cancel

See “Buttons common to every menu” on page 21.

Streaming Tab

Use this tab to set the items for the transmission by

unicast or multicast.

Unicast streaming

Specify the transmission port numbers of the H.264

video data and audio data to be used when Unicast is

selected from the Connection drop-down list in the

Other panel on the live viewer.

Video port number 1, 2, 3

Specify the transmission port number of the H.264 video

data. The default setting is 50000, 52000 or 54000.

Specify an even number from 1024 to 65534. Two port

numbers (the number specified here and an odd number

with 1 added to the specified number) are actually used

for video data communication and control. When

performing simultaneous multi-transmission, a different

port number will be used for every transmission, based

on the port number specified here.

The settings for Image 1, Image 2 and Image 3 apply to

Video port number 1, 2 and 3 respectively.

Audio port number

Specify the transmission port number of the audio data.

It is initially set to 56000. Specify an even number from

1024 to 65534. Three port numbers (the number

specified here and an odd number with 1 added to the

specified number) are used for audio data

communication and control. When operating multi-

transmission at the same time, a different port number

will be used in every transmission based on the port

number specified here.

Note

Specify different numbers for the video port number and

the audio port number.

RTSP video port number 1, 2, 3

Specify the H.264 video transmission port number used

for RTSP unicast streaming. The default setting is

51000, 53000 or 55000. Specify an even number from

1024 to 65534. Two port numbers (the number specified

here and an odd number with 1 added to the specified

number) are actually used for video data communication

and control. When performing simultaneous multi-

transmission, a different port number will be used for

every transmission, based on the port number specified

here.

The settings for Image 1, Image 2 and Image 3 apply to

RTSP video port number 1, 2 and 3 respectively.

RTSP audio port number

Specify the audio transmission port number used for

RTSP unicast streaming. The default setting is 57000.

Specify an even number from 1024 to 65534. Two port

numbers (the number specified here and an odd number

with 1 added to the specified number) are actually used

for audio data communication and control. When

performing simultaneous multi-transmission, a different

port number will be used for every transmission, based

on the port number specified here.

Multicast streaming

Set whether the camera uses multicast streaming for

H.264 video data and audio data or not. It reduces the

transmission load on the camera by having a computer

of the same segment network receive the same

transmitting data.

Enable

Select the checkbox to allow multicast sending.

When you select the checkbox, set Multicast address,

Video port number and Audio port number properly.

Multicast address 1, 2, 3

Type the multicast address used on the multicast

streaming.

Administrating the Camera

Setting the Camera Image and Audio — Video / Audio Menu 35

Video port number 1, 2, 3

Specify the H.264 video transmission port number used

for the multicast streaming. The default setting is 60000,

62000 or 64000. Specify an even number from 1024 to

65534. Two port numbers (the number specified here

and an odd number with 1 added to the specified

number) are used for video data communication and

control.

The settings for Image 1, Image 2 and Image 3 apply to

Video port number 1, 2 and 3 respectively.

Audio port number

Specify the audio transmission port number used for the

multicast streaming. It is initially set to 58000. Specify

an even number from 1024 to 65534. Two port numbers

(the number specified here and an odd number with 1

added to the specified number) are used for audio data

communication and control.

Note

Specify different numbers for the video port number and

the audio port number.

RTSP multicast address

Set the multicast address used on RTSP multicast

streaming.

RTSP multicast video port number 1, 2, 3

Specify the H.264 video transmission port number used

for RTSP multicast streaming. The default setting is

61000, 63000 or 65000. Specify an even number from

1024 to 65534. Two port numbers (the number specified

here and an odd number with 1 added to the specified

number) are actually used for video data communication

and control.

The settings for Image 1, Image 2 and Image 3 apply to

RTSP video port number 1, 2 and 3 respectively.

RTSP multicast audio port number

Specify the audio transmission port number used for

RTSP multicast streaming. The default setting is 59000.

Specify an even number from 1024 to 65534. Two port

numbers (the number specified here and an odd number

with 1 added to the specified number) are actually used

for audio data communication and control.

RTSP setting

Set the RTSP setting which cannot be set in the Unicast

streaming setting and Multicast streaming.

RTSP port No.

Set the port number used for RTSP streaming. The

default setting is 554.

If you change the setting, the RTSP server will be

rebooted.

RTSP time out

Specify the time out of the Keep-Alive command by

RTSP streaming. You can set the time out from 0 second

to 600 seconds.

At the 0 setting, time out of the Keep-Alive command is

not available.

OK/Cancel

See “Buttons common to every menu” on page 21.

Administrating the Camera

Configuring the Network — Network Menu

Configuring the Network

— Network Menu

When you click in the Administrator menu, the

Network menu appears.

Use this menu to configure the network to connect the

camera and the computer.

The Network menu consists of the Network, QoS and

UPnP tabs.

Network Tab

This section provides the menus for connecting the

camera through the network cable.

Status

MAC address

Displays the MAC address of the camera.

Ethernet status

Displays the current transmission rate.

Auto-MDI/MDIX

According to the port of the connected Ethernet

device, automatically switches the port of the unit

between MDI and MDI-X for transmission.

Displays the Ethernet port mode of the unit.

IP address

Displays the current IP address.

Subnet mask

Displays the current subnet mask.

Default gateway

Displays the current default gateway.

LinkLocal IP address

Displays the current link-local IP address.

Primary DNS server

Displays the current primary DNS server.

Secondary DNS server

Displays the current secondary DNS server.

IPv6 address 1, 2

Displays the current IPv6 address.

IPv6 default gateway

Displays the current IPv6 default gateway.

LinkLocal IPv6 address

Displays the current link-local IPv6 address.

IPv4 setting

Configure the IPv4 network setting.

To obtain the IP address automatically from

a DHCP server

Select Obtain an IP address automatically

(DHCP).

The IP address, subnet mask, default gateway are

assigned automatically.

Note

When you select Obtain an IP address

automatically (DHCP), make sure that a DHCP

server is operating on the network.

To specify the IP address manually

Deselect Obtain an IP address automatically

(DHCP). Type the address in the IP address,

Subnet mask and Default gateway boxes. Host

name and Domain suffix are not available.

IP address

Type the IP address of the camera.

Subnet mask

Type the subnet mask.

Default gateway

Type the default gateway.

Network

Administrating the Camera

Configuring the Network — Network Menu 37

Host name

Type the host name of the camera to be transmitted

to the DHCP server. This setting is valid only when

Obtain an IP address automatically (DHCP) is

selected.

Domain suffix

Type the domain suffix of the camera to be

transmitted to the DHCP server. This setting is valid

only when Obtain an IP address automatically

(DHCP) is selected.

Note

The domain suffix is sent to the DHCP server as

FQDN (Fully Qualified Domain Name)

information when Host name is set.

IPv6 setting

Configure the IPv6 network setting.

To obtain the IPv6 address automatically

Select Obtain IP address automatically.

The IP address, prefix length, default gateway are

assigned automatically.

Note

If you select Obtain IP address automatically, ask

the network administrator whether an IPv6 address

can be assigned.

This function is not available in a multi-prefix

environment. The transmission may not work

properly.

To specify the IPv6 address manually

Deselect Obtain IP address automatically. Type

the address in the IP address, Prefix length and

Default gateway boxes.

IP address

Type the IP address of the camera.

Prefix length

Type the prefix length value.

Default gateway

Type the default gateway.

Common setting

Configure the common setting for IPv4 and IPv6

network.

HTTP port number

Type the HTTP port number. Normally select 80.

MTU

Type the MTU value for the Ethernet port.

To obtain DNS server address

automatically

Select Obtain DNS server address automatically.

The Primary DNS server and Secondary DNS

server are assigned automatically.

Note

To obtain a DNS server address automatically, first

enable Obtain an IP address automatically

(DHCP) in the IPv4 setting, or Obtain IP address

automatically in the IPv6 setting.

Ask the network administrator whether a DNS

server address can be obtained automatically.

To specify the DNS server address

manually

Deselect Obtain DNS server address

automatically. Type the address in the Primary

DNS server and Secondary DNS server boxes.

Primary DNS server

Type the IP address of the primary DNS server.

Secondary DNS server

Type the IP address of the secondary DNS server, if

necessary.

OK/Cancel

See “Buttons common to every menu” on page 21.

QoS Tab

In this tab, you can mark the data traffic packets sent

from the device and configure the settings for QoS

control. Rules for the types of data traffic can be created

using IPv4 address, port number, protocol, etc. A

maximum of 10 rules can be registered.

Administrating the Camera

Configuring the Network — Network Menu

IPv4 QoS

Enable

Select the checkbox to configure the QoS setting for

IPv4.

Rule

Used to register, edit and delete QoS.

No.

Select the number to use when registering on the QoS

table.

When you select a registered number, the registered QoS

information is displayed.

Network address

Enter the network address of the target on which to

perform QoS.

Subnet

Enter the subnet mask values of the target on which to

perform QoS.

Tip

The subnet mask value represents the number of bits

from the left side of the network address.

Protocol

Select the protocol.

Port

Enter the port number for the data traffic of the device

(e.g. HTTP:80).

DSCP

Set a value to mark the data traffic (0 ~ 63).

This value is set in the DSCP field included in the IP

header of the data traffic.

Set

Used when registering on the QoS table.

QoS is set according to the following procedure:

Select No. from No. and enter the necessary

conditions for Network address, Subnet, Protocol

and/or Port No..

Enter values in DSCP.

Click Set and configure the QoS.

Delete

select No. to delete the setting and click Delete.

Move up

Increases the priority of the rule.

Select a rule from the QoS table to prioritize and click

Move up.

Move down

Decreases the priority of the rule.

Select a rule from the QoS table to lower its priority and

click Move down.

QoS table

Displays the list of registered QoS information. If

multiple conditions match, the rule with the smallest

number has priority.

OK/Cancel

See “Buttons common to every menu” on page 21.

UPnP Tab

Set UPnP (Universal Plug and Play).

Discovery

Enable

If the UPnP discovery function is enabled, you can

search the camera by using UPnP. If you want to disable

this function, deselect the checkbox for the UPnP

discovery function.

OK/Cancel

See “Buttons common to every menu” on page 21.

Administrating the Camera

Setting the Security — Security Menu 39

Setting the Security

— Security Menu

When you click in the Administrator menu, the

Security menu appears.

The Security menu consists of the User, Access limit,

SSL, 802.1X and Referrer check tabs.

User Tab

Set the user names and passwords of Administrator and

up to 9 types of user (User 1 to User 9), and the viewer

mode of each user.

Administrator, User 1 to 9

Specify User name, Password, Re-type password and

Viewer mode for each user ID.

User name

Type a user name between 5 and 16 characters.

Password

Type a password between 5 and 28 characters.

To enhance security, we strongly recommend you set a

password with 8 to 28 characters including both

numbers and letters.

Re-type password

To confirm the password, retype the password that you

typed in the Password box.

Audio

Set whether to enable the audio output from the speaker

of the camera. Select the checkbox to enable.

Note

Be sure to set Audio upload in the Audio tab of the

Video / Audio menu to Enable.

Playback

Set whether to enable using the playback viewer. Select

the checkbox to enable.

Viewer mode

When the user is authenticated for logging in the viewer,

select the viewer mode to be displayed after

authentication.

Administrator: The user can operate all functions in

this mode.

Full: The user can operate all functions except deleting

the recorded movie in the memory card.

Pan/Tilt: In addition to the Light mode, the user can

operate pan/tilt/zoom.

Light: In addition to the View mode, the user can select

the image size of the live viewer, select codec and

capture a still image.

View: The user can only monitor the camera image.

For the functions available for each viewer mode, see

“Administrator and User” on page 10.

Viewer authentication

Set whether the user is authenticated or not when the

viewer is displayed.

When the checkbox is selected, the viewer is displayed

in accordance with the viewer mode of the authenticated

user. When the checkbox is not selected, select the

viewer mode of the viewer which is displayed without

authentication from Full, Light or View.

Note

Setting viewer authentication can prevent unintended

third parties from viewing the video.

Without setting the viewer authentication, people can

view the video without inputting a user ID or password.

To prevent unintended third parties from viewing the

video, we strongly recommend for you to set viewer

authentication and change the password on a regular

basis.

Authentication mode

Set the authentication method for user authentication.

Basic authentication: Use the basic access

authentication.

Digest authentication: Use the digest access

authentication.

Note

If you change the settings in Authentication mode,

close the web browser and access again.

OK/Cancel

See “Buttons common to every menu” on page 21.

Security

Administrating the Camera

Setting the Security — Security Menu

Access limit Tab

This allows you to control which computers can have

access to the camera.

Likewise, when using IPv6, security settings can be

configured for each network.

Enable

Select the checkbox to enable the access limit.

Default policy

Select the basic policy of the limit from Allow and Deny

for the computers specified in the Network address/

Subnet 1 to Network address/Subnet 10 menus below.

Network address/Subnet 1 to Network

address/Subnet 10

Type the network addresses and subnet mask values that

you want to allow or deny access to the camera.

You can specify up to 10 network addresses and subnet

mask values. For a subnet mask, type 8 to 32.

(In the case of IPv6, enter a value between 8 and 128.)

Select Allow or Deny from the drop-down list on the

right for each network address/subnet mask.

Tip

The subnet mask value represents the bit number from

the left of the network address.

For example, the subnet mask value for “255.255.255.0”

is 24.

If you set 192.168.0.0/24 and Allow, you can allow

access from computers having an IP address between

“192.168.0.0” and “192.168.0.255”.

Note

You can access the camera even from a computer having

an IP address whose access right is set to Deny, if you

enter the user name and password set for the

Administrator boxes in the User menu.

OK/Cancel

See “Buttons common to every menu” on page 21.

SSL Tab

Configure the SSL or TLS function (called “SSL”

hereafter). The settings allow the camera to

communicate with the client PC by using SSL.

Notes

• The model on sale in China does not support the SSL

function.

Administrating the Camera

Setting the Security — Security Menu 41

• When using the SSL function, always configure the

settings after setting the date and time of the camera.

If the date and time are not correctly set, it may cause

browser connection problems.

• Reload the window when you change the SSL setting.

Press the F5 key on the keyboard to reload.

Common setting

SSL function

Select Enable to use the SSL function.

When Enable (Allow HTTP connection for some

clients) is selected, both HTTP and SSL connections are

allowed. When Enable is selected, only SSL connection

is allowed.

When Internet Explorer is used

When SSL session is established, appears in the right

of the address bar on your web browser.

When you use SSL connection for the first time

When you use SSL connection only with the SSL

function Enable, you cannot access the camera if the

SSL function does not work properly.

In this case, you must reset the camera to the factory

settings. (All settings will be initialized.)

To avoid this, check that SSL connection is possible by

performing the following steps.

Set the SSL function to Enable (Allow HTTP

connection for some clients).

Click OK to close the viewer and the setting

window.

Display the viewer in SSL connection.

Refer to “Using the SSL function” on page 6 for

connection.

After confirming that SSL connection is possible,

set the SSL function to Enable.

Even if the setting window or the browser is closed as

SSL connection is impossible, http connection will be

possible if Enable (Allow HTTP connection for some

clients) is selected. First check the setting contents of

SSL tab in http connection, then check the SSL

connection again.

If Enable (Allow HTTP connection for some clients)

is not selected, you will not be able to access the camera

if SSL connection becomes impossible. In this case, turn

on the power of the main unit while pressing the reset

switch on the camera to initialize. For details, refer to the

supplied Installation Manual.

Note

SSL connection will load the camera down; therefore,

not all images may be downloaded, and the mark

may appear when the camera accesses the setting

window from the browser. In this case, reload the

window. Press the F5 key on the keyboard to reload.

SSL server authentication

Certificate options

Select an installation mode of the certificate.

Use an external certificate: Uses the certificate

including private key information issued by a CA.

The PKCS#12 and PEM formats are supported.

Note

SSL is not available when Certificate options-Use an

external certificate is selected, or certificate and private

key password is not set properly even SSL is set to

“Enable”.

Use a self-signed certificate (For test use): This mode

uses the certificate and private key pair generated by

“Self-signed certificate generation” on page 42.

Private key information corresponding to the

certificate is stored in the camera.

You do not need to install an external certificate.

However, you cannot execute the existence proof that

is one of the SSL functions for the following reasons.

– The private key generated in the camera is self-

signed by the camera.

– A prepared value is set for a distinguished name

(Common name, etc).

– The certificate is not issued by a trusted CA.

For reasons of security, we recommend using this

mode only when there is no problem even if perfect

security is not saved.

Notes

•When Use a self-signed certificate (For test use) is

selected, the Security Alert dialog appears on the

SSL connection with a browser.

For details, refer to “Using the SSL function”

(page 6).

• SSL connection may be impossible due to the type of

certificate installed in the camera. In this case, refer to

“How to install the CA certificate” on page 43 and

install.

To import the certificate

Click Browse... to select the certificate to be imported.

Click the OK button appearing on the dialog when you

select the file, to import it to the camera.

Administrating the Camera

Setting the Security — Security Menu

Note

The import process becomes invalid if the selected file is

not a certificate or the imported certificate is not

allowed.

Self-signed certificate generation

A self-signed certificate can be generated in the camera

to be used when Use a self-signed certificate (For test

use) is selected from Certificate options.

Click Generate to generate a self-signed certificate in

the camera. Clicking Generate again after Generate

has been clicked once will update the self-signed

certificate stored in the camera.

Note

Make sure to set the date and time on the camera

correctly before performing this operation. If the date

and time are not correctly set, it may cause browser

connection problems. Before selecting Generate in

Self-signed certificate generation, click OK to select

Use a self-signed certificate (For test use) in

Certificate options.

To display certificate information

When the certificate has been set in the camera correctly,

its information appears on Status, Issuer DN, Subject

DN, Validity Period and Extended Key Usage.

Status

Shows if the status of the certificate is valid or invalid.

The following statuses are recognised.

Valid: The certificate is correctly stored and set.

Invalid: The certificate is not correctly stored and set.

Possible causes are as follows:

–Use an external certificate is selected and the

private key password included in the certificate is

not specified correctly.

–Use an external certificate is selected and the

private key password is specified in spite of the fact

that the key pair in the certificate is not encrypted.

–Use an external certificate is selected and the key

pair is not included in the certificate.

–Use a self-signed certificate (For test use) is

selected without the self-signed certificate being

generated.

Note

When the certificate to be imported is of PKCS#12

format and the private key password is not set correctly,

<Put correct private key password> is displayed in the

boxes of Issuer DN, Subject DN, Validity Period and

Extended Key Usage.

Specify the correct private key password to confirm the

information of the certificate.

To delete the imported certificate or self-signed

certificate

Click Delete to delete the certificate or self-signed

certificate imported to the camera.

Private key password

Type the password for the private key information

included in the certificate using up to 50 characters. This

text box is active only when Certificate options is set to

Use an external certificate.

Leave the text box blank if the private key information

included in the certificate is not encrypted.

If no private key password is set in the camera, an active

text field is displayed and this allows a password to be

entered.

If a private key password is already set, it is displayed as

an inactive text field.

Reset

To change the private key password, click this button.

The current password is cleared and the password text

box becomes active to allow a new password entry.

Note

Click Cancel at the bottom of the menu if you want to

cancel changing the private key password after clicking

Reset. Doing so restores the other setting items in the

Client certificate tab to the previous settings.

SSL client authentication

In this tab, you can manage the CA certificate needed for

the camera to use the client authentication of the SSL

function.

Notes

• When you use client authentication, the personal

certificate must be imported to your PC properly. For

details, see “To import the personal certificate” on

page 45.

If this preparation cannot be performed, do not

configure settings on this tab. Otherwise, you may not

be able to connect to the camera.

• The setting of SSL client authentication is available

only when SSL server authentication certificates are

uploaded.

Enable

You can configure whether to enable the client

authentication of the SSL function.

Trusted CA certificate 1 to 4

You can import a trusted CA certificate (route

certificate, etc.) to the camera.

Up to four certificates from trusted CAs can be imported

to the camera. Only PEM format is supported.

Administrating the Camera

Setting the Security — Security Menu 43

To import the CA certificate

Click Browse… to select the CA certificate to be

saved in the camera.

Click the OK button appearing on the dialog.

The selected file will be imported to the camera.

Note

Import process will be invalid if the selected file is not a

CA certificate.

To display the information of the CA certificate

When the CA certificate has been saved in the camera

correctly, its information appears on Issuer DN,

Subject DN, Validity Period, and Extended Key

Usage for your reference.

To delete the CA certificate

Click Delete to delete the selected CA certificate from

the camera.

Tip

To enable a client certificate, it is recommended that the

settings are configured following the procedure below:

1Import the necessary CA certificate.

2Select the SSL client authentication

checkbox and click OK.

Note

When you set SSL client authentication to Enable and

click OK, the camera will immediately operate to enable

client authentication. Make sure that the personal

certificate is imported to your PC in advance.

For details, see “To import the personal certificate” on

page 45.

OK/Cancel

See “Buttons common to every menu” on page 21.

How to install the CA certificate

The camera may not be connected because the browser

(Internet Explorer) does not display whether the

certificate will be accepted or not due to the type of

certificate. In this case, install the CA certificate as

follows.

Save in the PC the certificate of CA which has

signed the certificate to be installed in the camera.

The extension of the certificate file is normally

“.cer”. Double-click this file. The following

Certificate dialog appears.

Click Installation Certificate....

The Certificate Import Wizard appears.

Click Next.

Administrating the Camera

Setting the Security — Security Menu

Select Automatically selects the certificate store

based on the type of certificate and click Next.

Completing the Certificate Import Wizard

appears.

Check the contents, then click Finish.

The CA certificate will be installed.

To remove an installed CA

certificate

In Internet Explorer, click in the order Tools,

Internet options, Content tab and Certificates.

The Certificates dialog appears.

Select the certificate you want to remove.

The CA certificate is usually stored in Trusted

Root Certification Authorities.

Click Remove.

Do you want to delete the certificate appears to

confirm.

Click Ye s .

The certificate will be removed.

There may be a case that a certificate cannot be

removed by the steps above due to the type of

certificate. Check the installation condition and

remove it following the steps below.

Note

You need to log in as Administrator to perform these

steps.

Open Run... of the Windows menu, then enter mmc

and click OK.

Select File in the Console 1 window and Add/

Remove Snap-in... (when Windows XP

Professional is used).

Add/Remove Snap-in... dialog appears.

Select Certificates from the list, then click Add.

Certificate Snap-in is displayed.

Select Computer account as the certificate

administrated in this Snap-in, then click Next.

Select Local Computer as the computer

administrated in this Snap-in, then click Finish.

The items for administrating Certificates appears

in the Console Route window.

Confirm the relevant certificate, then remove it.

Administrating the Camera

Setting the Security — Security Menu 45

To import the personal certificate

To use client authentication, follow the steps below to

import the personal certificate.

Double click the personal certificate stored in your

PC.

Certificate Import Wizard is displayed.

Start importing by marking Enable this key as

exportable during the process.

Display sample: If the OS language is English

802.1X Tab

Configure the wired port-based authentication in

compliance with the 802.1X standard.

Notes

• To use the 802.1X authentication function, you need

knowledge of the 802.1X authentication and digital

certificate. To establish an 802.1X network, you need

to configure the authenticator, authentication server

and other elements. For details on these settings, refer

to the manual of the corresponding equipment.

Administrating the Camera

Setting the Security — Security Menu

• When using the 802.1X authentication function,

always configure the settings after setting the date and

time of the camera. If the date and time are incorrect,

port authentication may not be performed correctly.

System configuration of 802.1X

network

The following figure shows a general system

configuration of an 802.1X network.

Supplicant

A supplicant is a device that connects to the

authentication server to join the network. This camera

serves as a supplicant in the 802.1X network. The

supplicant can enter the 802.1X network after

appropriate authentication by the authentication server.

Authenticator

An authenticator forwards certificate request data or

response data that the supplicant or authentication server

issues to the other party. Normally a hub, router or

access point serves as an authenticator.

Authentication server

An authentication server has a database of connecting

users and verifies if the supplicant is a valid user or not.

It can also be called RADIUS server.

CA (Certificate Authority)

A CA issues and manages certificates of the

authentication server (CA certificates) and user

certificates. The CA is essential for certificate-based

user authentication. Normally a CA is located inside an

authentication server.

Note

This camera supports EAP mode in which the supplicant

and the server authenticate using the certificate. This

mode requires a CA to issue the certificate.

Common setting

Enable

Select the checkbox to enable the 802.1X authentication

function.

EAP identity

Type the user name to identify the client in the 802.1X

authentication server up to 250 characters.

EAP password

A supplicant EAP password is needed to be inputted

when PEAP is selected with EAP condition. The

password can contain half-width letters and the length

should be within 50 characters.

Reset

To change the once set EAP password, click Reset and

clear the current password. A new password can be

entered.

Note

After you click Reset, if you wish to cancel the EAP

password change, click Cancel at the bottom of the

screen. This will cancel other changes made to the

settings.

EAP method

You can select the authentication method used with the

authentication server. This device supports TLS and

PEAP.

TLS: By this method, the supplicant and the server

authenticate each other using a certificate. This

enables secure port authentication.

PEAP: By this method, an EAP password is used for the

supplicant authentication and a certificate is used for

server authentication.

Client certificate

When TLS is selected as the EAP method, the client

certificate is imported, displayed or deleted for the

camera authentication.

To import the client certificate

Click Browse… to select the client certificate to be

imported.

Click the OK button appearing on the dialog, and the

selected file will be imported to the camera.

Note

The import process becomes invalid if the selected file is

not a client certificate or the imported client certificate is

not allowed.

To display the information of the client

certificate

When the client certificate has been saved in the camera

correctly, its information appears on Status, Issuer DN,

Subject DN, Validity Period and Extended Key

Usage.

Supplicant

(camera)

Authenticator

(hub or router)

Authentication

server + CA

Administrating the Camera

Setting the Security — Security Menu 47

Status

Shows if the status of the client certificate is valid or

invalid.

Valid means the client certificate is correctly stored

and set.

Invalid means the client certificate is not correctly

stored and set.

Possible causes of Invalid are as follows:

– The private key password included in the client

certificate is not specified correctly.

– The private key password is specified in spite of

the fact that the key pair in the client certificate is

not encrypted.

– The key pair is not included in the client certificate.

Note

When the client certificate to be imported is of

PKCS#12 format and the private key password is not set

correctly, “<Put correct private key password>” is

displayed in the boxes of Issuer DN, Subject DN,

Validity Period and Extended Key Usage. Specify the

correct private key password to confirm the information

of the certificate.

To delete the client certificate

Click Delete, and the client certificate stored in the

camera will be deleted.

Private key password

Type the password for the private key information

included in the client certificate using up to

50 characters.

Leave the text box blank if the private key information

included in the client certificate is not encrypted.

If a private key password is already set, it is displayed as

turned letters.

Reset

To change the private key password, click this button.

The current password is cleared and the password text

box is actived to allow new password entry.

Note

Click at the bottom of the screen if you want to

cancel changing the private key password after clicking

Reset. Doing so restores the other setting items in the

Client certificate tab to their previous settings.

CA certificate

You can import a trusted CA certificate (server

certificate or route certificate) to the camera. Up to four

certificates from trusted CAs can be imported to the

camera. Only the PEM format is supported.

To import the CA certificate

Click Browse… to select the CA certificate to be

imported.

Click the OK button appearing on the dialog, and the

selected file will be imported to the camera.

Note

Import process becomes invalid if the selected file is not

a CA certificate.

To display the information of the CA certificate

When the CA certificate has been saved in the camera

correctly, its information appears on Issuer DN,

Subject DN, Validity Period and Extended Key

Usage.

To delete the CA certificate

Click Delete, and the CA certificate stored in the camera

will be deleted.

OK/Cancel

See “Buttons common to every menu” on page 21.

Referrer check tab

Referrer check checks if the web page which requires

access is authorized when the camera is accessed. If the

web page is not authorized, the camera denies access of

the web page to the camera.

If you want to access from web pages other than the one

that the camera provides, register their host names and

port numbers in the Exception list.

Referrer check

Select the checkbox for the Referrer check.

Exception list

check.

No.

Select the registered numbers of the Exception list.

Host name

Type the host name or IP address of the PC that supplies

the web page you want to register on the Exception list.

Port No.

Type the host name or the port number of the PC that

supplies the web page you want to register on the

Exception list.

Cancel

Administrating the Camera

Setting the PTZF control — PTZF control Menu

Set

typed to the list of the selected number.

Delete

Delete the contents of the list selected in No.

OK/Cancel

See “Buttons common to every menu” on page 21.

Setting the PTZF control

— PTZF control Menu

When you click in the Administrator menu,

the PTZF control menu appears.

The PTZF control menu consists of the PTZF control,

Preset position, Preset tour and Serial tabs.

PTZF control Tab

PTZ mode

Select the pan/tilt control mode using the 8-direction

arrow buttons (page 15) and the zoom control mode

using the / buttons (page 16).

Select Normal or Step.

Normal: When you click the mouse button, the camera

starts panning, tilting or zooming, and the operation

continues while you hold down the mouse button. To

stop the operation, release the mouse button.

Step: Each time you click the mouse button, the camera

moves (pans, tilts or zooms). If you keep the mouse

button held down for more than 1 second, the

operation mode is temporarily changed to Normal.

When you release the mouse button, camera

operation stops and the Step mode is restored.

When you select Step, Pan/Tilt level and Zoom level

are selectable.

Pan/Tilt level: Select the camera transition level from 1

to 10 by clicking the 8-direction arrow buttons for

panning/tilting. Selecting 10 provides the maximum

transition level.

Zoom level: Select the camera transition level from 1 to

10 by clicking / for zooming. Selecting 10

provides the maximum transition level.

Auto flip

This function automatically switches the tilt movement

of the camera downward to upward when the camera

tilts downward to the point where it faces the ground.

PTZF control

Administrating the Camera

Setting the PTZF control — PTZF control Menu 49

Enable

Select the checkbox to enable the auto flip function.

When you hold , or on the control panel to

make the direction of the camera pass through the point

where it faces the ground, the auto flip function is

activated, and the displayed picture is reversed.

When you deselect the checkbox, the direction of the

camera stops at the point where it faces the ground.

Latency

While Auto flip is set to On, set the time duration before

restarting tilt when the direction of the camera has tilted

completely downward.

Selectable values are 0 sec., 0.5 sec. are 0.75 sec.

Panorama mode

Select to rotate or not rotate the panorama image

displayed in the viewer in accordance with the pan

movement of the camera.

Rotate: The panorama image rotates as the camera

pans.

Fixed: The panorama image is fixed.

Zoom mode

Select the zoom mode.

Full: An image can be zoomed up to 30× optical zoom

and 12× digital zoom, 360× zoom in total.

Optical: An image can be zoomed up to 30× optical

zoom.

Focus mode

Select the focus mode.

Auto: The focus is automatically adjusted.

Manual: The focus can be adjusted by using the ,

and buttons of the control panel

displayed in the main viewer.

Horizontal tilt limit

Limit the tilting of the camera so the tilt does not lean

over the horizontal position to the camera side.

When Horizontal tilt limit is set to On, the camera does

not lean past the horizontal position on the camera side.

Focus near limit

Set the range at which to automatically focus. If a

subject is nearer than the set range, it will not be

focused.

Preset position Tab — Saving pan/

tilt/zoom position

You can set up camera pan, tilt and zoom positions to

256 positions.

Preview screen

This screen is for monitoring images and setting preset.

Set

Click to save a selected position, such as pan, tilt or

zoom positions in the preset. If Home is selected, the

position you saved will be assigned as the home

position.

Call

Move to the pan, tilt and zoom positions saved in the

selected preset.

Reset

If you click this when Home is selected, the home

position will be reset to the factory setting.

Add

Save the current pan, tilt and zoom positions as a new

preset.

Remove

Delete the selected preset.

Rename

Change the name of a selected preset.

Thumbnail

Check this checkbox to registers a thumbnail.

Select a radio button to determine whether to register the

current camera image as a thumbnail or to register with

a specified image.

To specify an image, click Browse.

Administrating the Camera

Setting the PTZF control — PTZF control Menu

Preset tour Tab — Setting a preset

tour

Up to 16 positions can be programmed, and the camera

moves to the programmed positions sequentially (Tour).

Up to five programs can be set as Tours A to E.

Preview screen

This screen is for monitoring images and configuring

preset tour settings.

Tour

Check to enable the tour function.

Resume time on inactivity

This item becomes active when Tour is set to On.

With this item, you can select whether you restart or stop

the tour after it has stopped by manual pan, tilt or zoom

operation or by camera movement to the preset position

triggered by an alarm.

Select the checkbox to set the resume time on inactivity.

Specify the wait time before the tour restarts, between 5

and 3600 seconds. The tour restarts automatically after

the specified time has elapsed.

Tour A to Tour E

Configure Tour A to Tour E respectively. Select the

checkbox to operate the tour.

Sequence

Set the sequence of the tour.

The preset positions saved using the Preset position tab

are displayed in the drop-down list at the bottom.

Select the preset position, then click Add. The selected

preset position is added in the Sequence list. Repeat this

procedure to specify the preset positions in sequence.

You can check the preset position by clicking Call.

To delete the preset position, click to select it in the list

and then click Delete.

To change the order in the list, select the preset position

and then click Move up or Move down.

To delete all preset position, click Delete All.

Speed

Select the speed of camera movement between 1 and 23,

or Fastest from the drop-down list. The camera moves

faster with a higher number setting. The fastest speed is

obtained with Fastest.

Stay time

Type a period of time during which the camera is to stay

at each preset position, between 1 and 3600 seconds.

Preview

Previews the order of movements of the selected tour.

The operation speed and stop time do not influence the

preview operation.

Stop

Stops the preview in action.

OK/Cancel

See “Buttons common to every menu” on page 21.

Serial Tab

Perform settings to control the camera according to data

which is input by peripheral devices via an external

serial interface. This unit complies with the Pelco-D

protocol. Make the settings according to the peripheral

devices connected to the network.

Standard

Select RS422, RS485 (half-duplex) or RS485 (full-

duplex).

Termination

Select the checkbox if you want to terminate it.

Camera ID

Specify the Camera ID of this unit.

OK/Cancel

See “Buttons common to every menu” on page 21.

Administrating the Camera

Setting the Sensor input/Camera tampering detection/Motion detection — Action input Menu 51

Setting the Sensor input/

Camera tampering

detection/Motion

detection

— Action input Menu

When you click in the Administrator menu,

the Action input Menu appears. The Action input Menu

consists of the Event condition, Sensor input, Camera

tampering detection, Motion detection, Face

detection and Network disconnection tabs.

When the Motion detection or Face

detection tab is displayed for the first

time

When you click Motion detection or Face detection,

“Security Warning” is displayed.

When you click Ye s , ActiveX control is installed and the

Motion detection or Face detection tab is displayed.

Notes

• If Automatic configuration is enabled in the Local

Area Network (LAN) settings of Internet Explorer, the

image may not be displayed. In that case, disable

Automatic configuration and set the proxy server

manually. For the setting of the proxy server, consult

your network administrator.

• When you install ActiveX control, you should be

logged in to the computer as Administrator.

Event condition Tab

Create event execute conditions for each action.

Event condition 1, 2, 3, 4, 5

Select the event condition.

You can combine the alarm using the following event

execute conditions.

and: detect when both conditions happen within a

specified interval regardless of the sequence.

or: detect when either condition happens.

then: detect when each of the conditions happen within

a specified interval in sequence.

If you set the event condition to None, the following

alarm 1, 2, 3 menus appear.

1, 2, 3

Select the alarm.

Selectable alarms are as follows;

Sensor input 1: The external sensor that is connected to

sensor input 1 of the camera I/O port.

Sensor input 2: The external sensor that is connected to

sensor input 2 of the camera I/O port.

Sensor input 3: The external sensor that is connected to

sensor input 3 of the camera I/O port.

Sensor input 4: The external sensor that is connected to

sensor input 4 of the camera I/O port.

Camera tampering detection: The alarm is triggered if

the camera detects tampering, such as direction

shifting or spray.

Motion detection: The alarm is triggered by the motion

detection function.

VMF: The alarm is triggered by the VMF function.

Face detection: The alarm is triggered by the face

detection function.

Network disconnection: The alarm is triggered by

disconnection to a specific IP address.

Note

You cannot set Camera tampering detection and

Network disconnection in the same event condition.

Interval

Specify the interval time used when condition is set to

and, then.

In the case the condition is set as 1 and 2, the system

sounds an alarm when either 1 or 2 happens, and the

other happens within the specified interval.

In the case the condition is set as 1 then 2, the system

sounds an alarm when 1 happens, and then 2 happens

within the specified interval.

If you select “or” condition, this setting will be ignored.

The maximum duration to be set is 7200 seconds.

Action input

Administrating the Camera

Setting the Sensor input/Camera tampering detection/Motion detection — Action input Menu

Sensor input Tab — Set the sensor

input 1/2/3/4

Sensor input mode

Set the direction of the detected input signal to the

sensor input terminal of the camera.

Normally open: Triggers an alarm when the sensor

input is short-circuited.

Normally closed: Triggers an alarm when the sensor

input is open-circuited.

Notes

• Allow at least two seconds for the input signal to be

detected; otherwise, some events may not be detected.

• When you use video streaming by SSL connection, set

as follows. Some events may not be detected if the

camera is not in the following conditions.

–Set the Bit rate below 1 Mbps.

–Set the Frame rate below 30 fps.

– Use the video streaming below two transmissions at

the same time.

OK/Cancel

See “Buttons common to every menu” on page 21.

Camera tampering detection Tab —

Set the camera tampering detection

Note

Deselect the checkbox of Stabilizer in the Installation

tab of the System menu. After setting the camera

tampering detection, set the Stabilizer function again.

Enable

Select the checkbox to activate the function to detect

camera tampering, such as direction shifting or spray.

Detection status

Display the tampering detection state of the time when

Camera tampering detection tab is opened. To clear the

detection status, click Clear button.

Auto clear

Clear the detection status automatically.

Select the checkbox to set the time to be cleared

automatically. When the checkbox is not selected, the

detection status will not be cleared unless the Clear

button is pressed.

Auto clear time

Set the time from when the camera tampering detection

is detected until the detection status is cleared

automatically.

OK/Cancel

See “Buttons common to every menu” on page 21.

Motion detection Tab — Set the

motion/VMF detection

Motion detection responds to moving objects in the

camera image and triggers an alarm.

In VMF, an alarm sounds when motion is detected under

the motion detection setting, entering or passing through

a specified area or inspection line. An alarm also sounds

when an object has been left or removed from a specified

area or inspection line.

The detected object will be displayed on the monitor in

the green frame. The removed object and left object will

be displayed in the magenta frame.

Note

Perform the following before setting the motion

detection.

• Deselect the checkbox of Stabilizer in the Installation

tab of the System menu.

What is VMF

VMF is a function for detecting an object entering or

passing through a specified area or inspection line, or

when an object has been left or removed from a specified

area or inspection line. Video/audio recording and/or

audio file playback can be synchronized with this alarm.

You can set the inspection methods to execute

independently. Intrusion and Passing can also be set to

execute in combination.

For example:

• An alarm sounds when an object enters areas A, B and

Administrating the Camera

Setting the Sensor input/Camera tampering detection/Motion detection — Action input Menu 53

• An alarm sounds when an object passes through area

A and enters area B.

• An alarm sounds when an object passes through areas

A and B, and enters area C.

• An alarm sounds when an object enters area A, and

passes through area B.

Intrusion

When a moving object enters the designated area, an

alarm sounds.

Passing

A passage line is determined, and when a moving object

passes the setting line, an alarm sounds.

Left object

When a moving object has been left in the designated

area, an alarm sounds.

Removed object

When a moving object has been removed from the

designated area, an alarm sounds.

Notes

• Before actual use, perform an operation test and

confirm that the motion detection function works

correctly.

• When the privacy masking is used, the motion

detection function is not available for the masked area

if Effect is set to Opaque.

Setting items for motion detection

Use the settings tab to set the conditions for the motion

detection function while observing camera images.

Target Image

Select All PTZ position or Preset position.

All PTZ position

This is a common setting for both VMD and VMF

settings regardless of the camera PTZ position.

Preset position

You can set the VMD and VMF settings for each preset

position.

Selected preset

Displays the registered preset positions. Click a preset

position to position the camera, then make the VMD and

VMF settings for that position.

VMD settings

Detection area

Specify the effective scope of motion detection.

Note

The frames shown on the monitor screen are not

displayed on the image files sent or recorded with

motion detection.

Configuring the detection area

The following procedure is used to configure the motion

detection area:

Use the following buttons to specify the active

area(s) and inactive area(s).

Add detection area

Clicking this button will add an active area window

in the center of the screen.

When you place the cursor on the area, the cursor

changes to a crossed arrow, which you can drag to

move the area.

Monitor screen

Setting item list Setting area

Administrating the Camera

Setting the Sensor input/Camera tampering detection/Motion detection — Action input Menu

When you place the cursor on the vertex of the area,

the cursor changes to n, which you can drag to

move the vertex.

Add non detection area

Clicking this button will add an inactive area

window in the center of the screen.

When you place the cursor on the area, the cursor

changes to a crossed arrow, which you can drag to

move the area.

When you place the cursor on the vertex of the area,

the cursor changes to n, which you can drag to

move the vertex.

Delete Area

Clicking this button will change the cursor to a

button. While the cursor is a button, click on a part

of the area to delete that area.

After the deletion, the cursor will return to its

original form. To exit this operation, click this

button again.

It is the same function as the button displayed under

VMF settings.

Add vertex

Clicking this button will change the cursor to a

button. In that state, when you click on a part of the

side of the area, a vertex is added to that point. After

the addition, the cursor will return its original form.

To exit this operation, click this button again.

It is the same function as the button displayed in

VMF settings.

Delete vertex

Clicking this button will change the cursor to a

button. In that state, when you click on a part of the

vertex of the area, the vertex added to that point is

deleted. After the deletion, the cursor will return its

original form. To exit this operation, click this

button again.

It is the same function as the button displayed in

VMF settings.

Note

The vertex can be moved in an outward direction

but cannot be moved toward the inside of an area.

Detection sensitivity

Set the sensitivity of motion detection.

A value from 1 to 256 can be specified.

Clicking Return to the default changes the value to the

default value.

Detection response

Set the response velocity of motion detection.

A value from 1 to 5 can be specified.

Clicking Return to the default changes the value to the

default value.

Detection size

Specify the minimum detection size and maximum

detection size for motion detection. To specify the

detection size, you can either enter values or drag the

vertexes of the area.

The area size is measured in pixels.

• When you place the cursor on the area, the cursor

changes to a crossed arrow, which you can drag to

move to the minimum detection size area and

maximum detection size area.

• When you place the cursor on the vertex of the area,

the cursor changes to n. Drag and move the vertex

to adjust the detection size.

Moving shadow exemption

Set ON/OFF for the moving shadow exemption function

of motion detection.

Selecting Do not respond to shadows will prevent the

shadows of a moving object from being recognized as

moving objects.

Deselect the checkbox to disable the shadow removal

function of motion detection.

Administrating the Camera

Setting the Sensor input/Camera tampering detection/Motion detection — Action input Menu 55

VMF settings

Set the alarm to sound when the specified conditions

(Intrusion, Passing, Left object, Removed object) of

the motion detection occur. You can also set the order for

Intrusion or Passing, and set the alarm to sound only

when the specified conditions occur in sequence.

Filter type

Select the filter type from Intrusion, Passing, Left

object, Removed object or Off.

Time until left/removed object is detected

Enter the time you want to elapse before the alarm is

triggered. This setting is available only when the filter

type is set to Left object or Removed object.

Filter settings

Settings for each filter can be edited here.

The inspection line and active window are set to default

values. Edit according to use.

x VMF status indicator of each filter

The filter is on when the set filter type conditions

(Intrusion, Passing, Left object, Removed object) are

met.

Tip

The buttons displayed on the edit screen for filter is used

in the same way as those for detection setting. See

page 53.

Intrusion

This criterion is for whether a moving object exists in

the trigger area.

Similar to an active window, a trigger area can also be

moved and vertexes can be moved, added or deleted.

Passing

Edit the pass inspection line according to the following

procedure:

Passing object trigger line

By default, one passing object trigger line is displayed.

The number of vertexes is 2.

Placing the cursor on the line will turn the cursor into a

cross, and when you drag the line, the whole line will

move.

Placing the cursor on the vertex will turn the cursor into

n, and when you drag the line, the vertex will move.

The arrow displayed in the center of the passing object

trigger line shows the direction of inspection. Trigger is

performed when an object passes the passing object

trigger position in this direction.

Trigger direction setting

Each time you click , the trigger direction toggles

among the directions left, right and both.

Passing object trigger position

Select the passing object trigger position from All sides,

Left side, Top side, Right side and Bottom side.

Administrating the Camera

Setting the Sensor input/Camera tampering detection/Motion detection — Action input Menu

Left object

This criterion is for whether a moving object has been

left in the trigger area.

Similar to an active window, a trigger area can also be

moved and vertexes can be moved, added or deleted.

Removed object

This criterion is for whether a moving object has been

removed from the trigger area.

Similar to an active window, a trigger area can also be

moved and vertexes can be moved, added or deleted.

Trigger size

Specify the minimum trigger size and maximum trigger

size of motion. To specify the size, you can either enter

values or drag the vertexes of the area.

The size of motion is measured in pixels.

• When you place the cursor on the area, the cursor

changes to a crossed arrow, which you can drag to

move the minimum trigger size area and maximum

trigger size area.

• Placing the cursor on the vertex of the minimum

trigger size area or maximum trigger size area will

change the cursor to n, then you can drag the vertex

to change the inspection size.

Tip

The minimum and maximum detection sizes configured

in the VMD setting are displayed, but the size of the area

cannot be modified from here.

Administrating the Camera

Setting the Sensor input/Camera tampering detection/Motion detection — Action input Menu 57

Trigger speed

Specify the minimum and maximum speeds to be

detected.

• Min. speed and Max. speed can be specified within a

scale of 100.

• The blue marker for minimum speed cannot be set to

the right of the red marker for maximum speed.

• The squares indicating Min. speed and Max. speed

move on the right and left sides of the preview screen.

Note

The set value is only valid under the conditions of

Intrusion or Passing.

Matching decision

Select the filter type you want to match and check Use

as matching condition.

Select Filter 1, Filter 2 and Filter 3 in the list box of

Matching decision.

Set the alarm to sound when the specified maximum 3

conditions occur in sequence. If the conditions occur in

a different order, the alarm will not sound. Select the

condition from Intrusion, Passing or None.

Filter order switching button

Clicking switches the order of filter between the

neighbouring methods.

e.g., If you click the button between 1 and 2, they will

switch order. If you click the button between 2 and 3,

they will switch order.

Specifying the time

Specify the reference interval in seconds between 1 and

2, or 2 and 3.

For example, if 1 and 2 are set and “3 seconds” is

specified, an alarm will sound when the inspection

conditions of 2 are met within 3 seconds from when the

inspection conditions of 1 are met.

x VMF status indicator of Matching

decision

The indicator is on when the set filter type conditions are

met.

Full-screen display button

Click to display the ActiveX area in full screen.

Clicking again will show the normal display.

Stretch bar

Click to hide the menu list on the left and enlarge the

preview screen.

Clicking again will show the menu list as it was before.

OK/Cancel

Click OK to finalize any changes made to the settings

and send them to the camera.

If you click Cancel, changes made to the settings will be

discarded and the screen will be reloaded with the

current camera settings.

Face detection Tab — Set the face

detection

Face detection responds to faces in the camera image

and triggers an alarm.

Notes

• Before actual use, perform an operation test and

confirm that the face detection function works

correctly.

Monitor screen

Setting item list Setting area

Administrating the Camera

Setting the Sensor input/Camera tampering detection/Motion detection — Action input Menu

• Perform the following before setting the face

detection.

– Deselect the checkbox of Stabilizer in the

Installation tab of the System menu.

• An inactive area cannot be specified.

• A horizontal face (leaning too far sideways) cannot be

detected.

• Vertexes cannot be added or deleted. They are for

specifying a rectangular area only.

• When the privacy masking is used, the motion

detection function is not available for the mask areas.

Target Image

Select All PTZ position or Preset position.

All PTZ position

This is a common setting for the face detection settings

regardless of the camera PTZ position.

Preset position

You can set the face detection settings for each preset

position.

Selected preset

Displays the registered preset positions. Click a preset

position to position the camera, then make the face

detection settings for that position.

Detection area

Specify the effective scope of face detection. You can set

the area in the same way as the detection area setting in

VMD settings. (page 53)

A maximum of ten detection areas can be set. Similar to

the detection area setting in VMD settings, a trigger area

and vertexes can also be moved.

Detection sensitivity

Set the sensitivity of face detection. A value from 0 to 64

can be specified. Select low values to limit detection to

the human face, or high values to also detect subjects

that are similar the human face. This makes detection

easier when the subject is far from the camera.

Clicking Return to the default changes the value to the

default value.

Detection size

Specify the minimum and maximum size of face

detection. You can specify the size by specifying values

or by dragging vertexes to choose the area.

OK/Cancel

Click OK to finalize any changes made to the settings

and send them to the camera.

If you click Cancel, changes made to the settings will be

discarded and the screen will be reloaded with the

current camera settings.

Network disconnection Tab

— Monitoring the connection of a

specified IP address

Monitored IP address

Set the specific IP address of which the network

connection status is to be monitored.

IP address monitoring is not available for IPv6.

OK/Cancel

See “Buttons common to every menu” on page 21.

Administrating the Camera

Setting the Action output — Action output Menu 59

Setting the Action

output — Action output

When you click in the Administrator

menu, the Action output menu appears.

The Action output menu consists of the Execution

Condition, Mail Transfer, Alarm output, Edge

Storage, Voice alert, HTTP alarm notification and

FTP still image sending tabs.

Execution Condition Tab

Set execute conditions for each action.

Set the action output execute conditions when the

condition created in the Event condition tab is

implemented.

Mail Transfer: Set the condition of mail transfer.

Alarm output 1: Set the condition to control alarm

output of the I/O port on the rear of the camera.

Alarm output 2: Set the condition to control alarm

output of the I/O port on the rear of the camera.

Edge Storage movie: Set the condition to record

movies using the Edge Storage function.

Edge Storage still image: Set the condition to record

still images using the Edge Storage function.

Voice alert 1: Set the condition of Voice alert 1 recorded

in the camera.

Voice alert 2: Set the condition of Voice alert 2 recorded

in the camera.

Voice alert 3: Set the condition of Voice alert 3 recorded

in the camera.

Preset call: Set the condition of preset call and the

preset call number.

HTTP alarm notification 1: Set the condition for the

HTTP alarm notification to recipient 1.

HTTP alarm notification 2: Set the condition for the

HTTP alarm notification to recipient 2.

HTTP alarm notification 3: Set the condition for the

HTTP alarm notification to recipient 3.

FTP still image sending: Set the condition for sending

with the FTP still image sending function.

Mail Transfer Tab — Setting the

e-Mail (SMTP) Function

SMTP Server

Notes

• You cannot send an audio file by using the e-mail

sending function.

• The frame rate and operability on the viewer may be

reduced while a file is being transmitted by the e-Mail

(SMTP) function.

SMTP server name

Type the SMTP server name using up to 64 characters,

or the IP address of the SMTP server.

SMTP port number

Enter a port number from 1 to 65535.

The standard port number is 25.

The standard port number of SMTPs is 465, if the TLS

function is enabled.

Use TLS

When using the encryption function of the TLS, select

the checkbox.

Action output

Administrating the Camera

Setting the Action output — Action output Menu

Note

Models sold in China do not support the TLS function.

Authentication

Select whether authentication is required when you send

an e-mail.

None: No authentication is required when an e-mail is

sent.

SMTP: Select when SMTP authentication is required.

POP before SMTP: Select when POP before SMTP

authentication is required.

Combination of POP before SMTP and SMTP:

Select when both SMTP authentication and POP

before SMTP authentication is required.

POP mode

Select POP3 or APOP as the authentication method for

POP authentication.

Note

The model on sale in China does not support the APOP

authentication.

Wait time after POP

Set the waiting time in POP before SMTP before

SMTP authentication after POP authentication is

completed. Timeout can be set from 0 to 10,000 msec.

POP server name

This is necessary when POP before SMTP is selected

for Authentication.

Type the POP (receiving mail) server name using up to

64 characters, or type the IP address of the POP server.

This setting is necessary when the SMTP server that

sends e-mails performs authentication using the POP

user account.

POP port number

Enter a port number from 1 to 65535.

The standard port number is 110.

POPs standard port number is 995, when the TLS is

enabled.

Authentication mode

Select Login or CRAM-MD5 as the authentication

method for SMTP authentication.

Note

The model on sale in China does not support the CRAM-

MD5 authentication.

User name, Password

Type the user name and password of the user who owns

the mail account using up to 64 characters. This setting

is necessary when the SMTP server that sends e-mails

performs authentication.

Address

Recipient e-mail address 1, 2, 3

Type the recipient e-mail address using up to 64

characters.

You can specify up to three recipient e-mail addresses.

Administrator e-mail address

Type the Administrator e-mail address using up to 64

characters.

This address is used for reply e-mails and sending

system messages from the mail server.

Content

Subject

Type the subject/title of the e-mail.

The length for entering letters should be within

64 characters.

An e-mail sent in response to alarm detection will

indicate the type of alarm in the subject. (Sensor1) is

added for sensor input 1 detection, (Sensor2) for sensor

input 2 detection, (Sensor3) for sensor input 3 detection,

(Sensor4) for sensor input 4 detection, (Tampering) for

camera tampering detection, (VMD) for motion

detection, (VMF) for VMF detection, (Disconnected)

for network disconnection detection, (Face Detection)

for face detection. (Event1 (Condition1)) is additionally

available for event condition detection.

Message

Type the text of the e-mail.

The length for entering letters should be within 384

characters.

Event triggered execution

File attachment

Set whether an image file (JPEG file) is to be attached to

the e-mail or not.

When the checkbox is selected, the image file made

using the settings below is attached. When the checkbox

is deselected, only the message is sent.

Image file name

Type the file name you want to assign to the image to be

attached to an e-mail. You can use up to 10

alphanumeric characters, – (hyphen) and _ (underscore)

for naming.

Administrating the Camera

Setting the Action output — Action output Menu 61

The actual image file name will be the specified image

file name with a suffix and the extension .jpg.

Suffix

Select a suffix to be added to the file name used when the

e-mail is sent.

None: The name of the sent file will be the image file

name.

Date & time: The date & time suffix is added to the

image file name.

The date & time suffix consists of last two-digits of

the year (2 digits), month (2 digits), date (2 digits),

hour (2 digits), minute (2 digits), second (2 digits),

and sequential number (2 digits), thus adding 14-

digit number to the image file name.

Periodical execution

You can set to send e-mails periodically.

Image file name

Type the file name you want to assign to the image to be

attached to an e-mail. You can use up to 10

alphanumeric characters, – (hyphen) and _ (underscore)

for naming.

The actual image file name will be the specified image

file name with a suffix and the extension .jpg.

Suffix

Select a suffix to be added to the file name used when the

e-mail is sent.

None: The name of the sent file will be the image file

name.

Date & time: The date & time suffix is added to the

image file name.

The date & time suffix consists of last two-digits the

year (2 digits), month (2 digits), date (2 digits), hour

(2 digits), minutes (2 digits) and seconds (2 digits),

and sequential number (2 digits), thus adding a 14-

digit number to the image file name.

Trouble sending

Set to send an e-mail when a memory card problem or

fan problem is detected.

Enable

Select the checkbox to enable the sending of problem

reports.

Continuous sending

Set whether to enable continuous e-mail sending.

When the checkbox is selected, an e-mail will be sent

once an hour.

Recipient e-mail address

Type the recipient's e-mail address within 64 characters.

OK/Cancel

See “Buttons common to every menu” on page 21.

Alarm output Tab — Setting the

Alarm output

You can perform setting in this menu to control the

alarm output of the I/O port on the rear of the camera

linked to alarm detection function.

Tip

For details on connection of peripheral devices to the

alarm output of the I/O port, refer to the supplied

Installation Manual.

Duration

Duration 1, 2

Enter the duration for which the alarm is output,

between 1 sec. and 60 sec.

Memory card trouble detection

Set to output the alarm when trouble of the memory card

is detected.

Output port 1, 2

Check the I/O port number that outputs the alarm when

the trouble of memory card is detected.

OK/Cancel

See “Buttons common to every menu” on page 21.

Administrating the Camera

Setting the Action output — Action output Menu

Edge Storage Tab — Setting the

Edge Storage movie and still image

function

With Edge Storage, video or audio signal can be

recorded from the alarm detection results, such as

network block, recorded video and audio can be

streamed with the same protocol as the real-time

streaming.

Notes

• The frame rate and operability on the viewer may be

reduced during movie or still image recording.

• The actual interval of recording a still image may be

longer than the interval you set.

• Stop the Edge Storage recording before you turn off

the power of the camera with a memory card inserted.

• Before you remove or insert a memory card, stop the

Edge Storage recording and turn off the power of the

camera.

• Before using a memory card, format it by Format

memory card in the Initialize tab of the System menu

(page 24).

• A maximum of 4000 movie records can be saved to an

memory card. If the checkbox of Overwrite is not

selected when the number of records reaches 4000,

new recordings cannot be made. If the checkbox of

Overwrite is selected when the number of records

reaches 4000, the unit will begin to overwrite old

records in ascending chronological order.

• Overwrite is not available for a memory card of less

than 4 GB.

• When recording H.264, the recorded data may

become very large and the video/audio may be

interrupted if the Adaptive rate control is set and other

image codec except CBR is selected. Therefore,

selecting CBR is recommended.

If you select CBR, set the video codec as follows:

–Set the

Bit rate

below 2000 kbps.

–Set the

Frame rate

below 30 fps.

–Set the

I-picture interval

to 1 second.

• When you record the JPEG with image size 1280 ×

720 or above, set the video codec as follows:

– SNC-WR630/WR632: Set the Image quality below

– SNC-WR600/WR602: Set the Image quality below

–Set the

Frame rate

to 1 fps.

• When you record, set the

Image codec 2

and

Image

codec 3

of the

Video codec

tab in the Video / Audio

menu to

Off

Common setting

Memory card

Display the available free space of external memory.

Maintenance information

Displays the status of the memory card if you are using

the memory card that corresponds to displaying

Maintenance information.

Overwrite

Select On to overwrite the file when there is insufficient

memory space.

When you select the checkbox, overwrite is enabled.

Old records will be overwritten in chronological order.

When you deselect the checkbox, overwrite is

prohibited, and no recording will be performed.

Note

Records are overwritten in chronological order,

regardless of whether they are movies or still images.

Edge Storage still image

Recording data

You can refer to still image files recorded in the memory

card. These files will be saved in a folder tree as follows.

/sdcard/EdgeStoragePicture/00000000-999999999/

00000000-99999999/

(Prefix)YYYYMMDDhhmmss00000001.jpg

Administrating the Camera

Setting the Action output — Action output Menu 63

Path: Displays the path name of the recording still

image file.

When you select a file, a still image will be displayed.

Delete: Click Delete to delete the selected folder or file.

If you select a folder, any files in the folder will also

be deleted.

Refresh: Click Refresh to reload the latest data.

Recording target

Select the video codec mode you want to record.

For detailed settings of video codec mode, see the Video

codec tab in the Video / Audio menu.

Notes

• You can record still images even if the video is

specified with an image codec set to H.264.

• Image quality setting for a still image can be changed

only when the image codec is set to JPEG.

• If you want to change the image quality of recorded

still images, change the image codec to JPEG.

• A folder containing no still image files may appear.

Image file name

The file name consists of three parts: a prefix, a file

number and an extension.

Set the prefix of up to 30 alphanumeric characters. You

can include - (hyphen) and _ (underscore) in the prefix.

The file number and extension are assigned

automatically by the camera.

The file number consists of the year (4 digits), month (2

digits), date (2 digits), hour (2 digits), minutes (2 digits),

seconds (2 digits), and a sequential number (8 digits).

Greenwich Mean Time will be included in the file name.

The extension is .jpg.

Edge Storage movie

Recording status

Display the current recording status.

The recording status will not be updated until the screen

is refreshed.

Use the Start Recording and Stop Recording button to

start or stop the recording manually.

Note

When recording manually, do not set Edge Storage

movie in the Execution Condition tab of the Action

output menu to Off.

Recording target

Video: Select the video codec mode you want to record.

For detailed settings of video codec mode, see the

Video codec tab in the Video / Audio menu.

Audio: Set whether to record the audio signals input

from the camera.

Select the checkbox to record.

Note

Set Audio sending (page 29) in the Audio tab of the

Video / Audio menu to Enable.

Recording capacity

Displays the maximum recording time in the current

camera setting of the video mode, image size, bit rate

and frame rate.

Pre-alarm period: Displays the maximum recording

time before the alarm is triggered.

Post-alarm period: Displays the maximum recording

time after the alarm is triggered.

Note

Maximum recording time varies depending on the

image size and quality setting in the Video / Audio

menu.

Recording time

Set the recording time for the Pre-alarm image/audio

and Post alarm image/audio.

Pre-alarm period: Type the recording time of the

image/audio before alarm detection.

Post-alarm period: Type the recording time of the

image/audio after alarm detection.

OK/Cancel

See “Buttons common to every menu” on page 21.

Voice alert Tab

Set the voice alert function, to output audio from the

speaker connected to the line output jack of the camera,

when an alarm is triggered by the sensor input or

detection functions.

Administrating the Camera

Setting the Action output — Action output Menu

Note

Before using the voice alert function, you need to save

the audio file to the camera using the SNC toolbox. You

can download SNC toolbox and application guides from

the download site.

Voice alert 1, 2, 3

Up to three voice alerts can be set. Configure the

following setting for each voice.

File

Displays the name of the audio file saved in the camera.

“Not uploaded” is displayed dimly if no audio file is

saved.

To delete the audio file saved in the camera, click

Delete.

Note

Before deleting an audio file, set Voice alert to Off.

Voice alert is included in the Execution Condition tab of

the Action output menu.

Test

When an audio file is saved in the camera, you can check

it by playing it back.

Click Play to play back the audio file.

Repeat

Select playback repeat time from 1 to 3.

Notes

• If voice alert is actively linked with a different alarm

type while another voice alert is occurring, the first

voice alert is cancelled and the second one is output.

• When you play back a test, do not set Voice alert in

the Execution Condition tab of the Action output

menu to Off.

• If two or three audio files are set to be output

simultaneously linked with the same alarm type,

priority is given in the order Voice alert 1, 2 then 3.

OK/Cancel

See “Buttons common to every menu” on page 21.

HTTP alarm notification Tab

Set to notify a specified URL of an alarm when an event

is detected.

HTTP alarm notification 1, 2, 3

Set up to 3 recipients who you want to notify of the

alarm.

User name

Type the user name for authentication using up to 64

characters.

Password

Type the password for authentication using up to 64

characters.

Notification at the beginning of event detection

Select the checkbox for the alarm notification when the

event detection starts.

URL

Type the recipient of the alarm.

Test

If you click Execute, the alarm will be notified

manually regardless of whether an event is detected.

Notification at the end of event detection

Select the checkbox for the alarm notification when the

event detection ends.

Note

If the VMF, Camera tampering detection, Face

detection, HTTP alarm notification, Event condition

are set as conditions for executing HTTP alarm

notification, the Notification at the end of event

detection cannot be set.

URL

Type the recipient of the alarm.

Test

If you click Execute, the alarm will be notified

manually regardless of whether an event is detected.

Use Proxy

Select the check box if you use a proxy server.

Address

Type the address of the proxy server using up to 255

characters.

Port No.

Type the port number of the proxy server using up to

255 characters.

User name

Type the user name for proxy server authentication

using up to 64 characters.

Password

Type the password for proxy server authentication

using up to 64 characters.

Administrating the Camera

Setting the Action output — Action output Menu 65

OK/Cancel

See “Buttons common to every menu” on page 21.

FTP still image sending Tab

Set the items for the still file images that are recorded at

alarm detection or recorded periodically and sent to the

FTP server.

Note

While transferring the files with FTP still image

sending, the frame rate and operability of the main

viewer decrease.

FTP server

Set the items for the FTP server where files will be sent.

Server name

Type the FTP server name of the FTP server where you

want to upload the files using up to 64 characters or type

the IP address of the FTP server.

User name

Type the user name for the FTP server using up to 64

characters.

Password

Type the password for the FTP server using up to 64

characters.

Passive mode

Set whether to use the passive mode of the FTP server

when you connect to the FTP sever. If you select the

checkbox, you can connect to FTP sever in passive

mode.

Alarm sending

Image to be sent

Select the video codec mode for the image of alarm

sending.

For detailed settings of video codec mode, see the Video

codec tab in the Video / Audio menu.

Remote path

Type the path where the files will be sent using up to 64

characters.

Image file name

Type the file name of the image that you want to send to

the FTP server using up to 10 alphanumeric characters,

- (hyphen) and _ (underscore).

Suffix

Select a suffix to be added to the file name used when the

image is sent.

Date & time: The date & time suffix is added to the

image file name.

The date & time suffix consists of last two-digits of

the year (2 digits), month (2 digits), date (2 digits),

hour (2 digits), minute (2 digits), second (2 digits),

and sequential number (2 digits), thus adding 14-

digit number to the image file name.

Sequence number: A sequential 10-digit number

0000000001-4294967295 and a sequential 2-digit

number are added to the image file name to be sent.

Sequence number clear

If you click Clear, the suffix of the Sequence number

returns 1.

Test

If you click Execute, the image will be sent to the FTP

server once for testing according to the settings of alarm

sending.

Periodical sending

Image to be sent

Select the video codec mode of the image of periodical

sending.

For detailed settings of video codec mode, see the Video

codec tab in the Video / Audio menu.

Remote path

Type the path where the files will be sent using up to 64

characters.

Image file name

Type the file name of the image that you want to send to

the FTP server using up to 10 alphanumeric characters,

- (hyphen) and _ (underscore).

Suffix

Select a suffix to be added to the file name used when the

image is sent.

None: The name of the sent file will be the image file

name.

Date & time: The date & time suffix is added to the

image file name.

The date & time suffix consists of last two-digits of

the year (2 digits), month (2 digits), date (2 digits),

hour (2 digits), minute (2 digits), second (2 digits),

and sequential number (2 digits), thus adding 14-

digit number to the image file name.

Sequence number: A sequential 10-digit number

0000000001-4294967295 and a sequential 2-digit

number are added to the image file name to be sent.

Administrating the Camera

Setting the Action output — Action output Menu

Sequence number clear

If you click Clear, the suffix of the Sequence number

returns 1.

Test

If you click Execute, the image will be sent to the FTP

server once for testing according to the settings of

periodical sending.

Tour sync sending

Tour

Select the checkbox to sync the tour.

Image to be sent

Select the video codec mode for the image of tour sync

sending.

For detailed settings of video codec mode, see the Video

codec tab in the Video / Audio menu.

Remote path

Type the path where the files will be sent using up to 64

characters.

Image file name

Type the file name of the image that you want to send to

the FTP server using up to 10 alphanumeric characters,

- (hyphen) and _ (underscore).

Suffix

Select a suffix to be added to the file name used when the

image is sent.

None: The name of the sent file will be the image file

name.

Date & time: The date & time suffix is added to the

image file name.

The date & time suffix consists of last two-digits of

the year (2 digits), month (2 digits), date (2 digits),

hour (2 digits), minute (2 digits), second (2 digits),

and sequential number (2 digits), thus adding 14-

digit number to the image file name.

Sequence number: A sequential 10-digit number

0000000001-4294967295 and a sequential 2-digit

number are added to the image file name to be sent.

Preset: A preset name is added to the image file name to

be sent.

Sequence number clear

If you click Clear, the suffix of the Sequence number

returns 1.

Test

If you click Execute, the image will be sent to the FTP

server once for testing according to the settings of tour

sync sending.

Manual sending

Image to be sent

Select the video codec mode of the image of manual

sending.

For detailed settings of video codec mode, see the Video

codec tab in the Video / Audio menu.

Remote path

Type the path where the files will be sent using up to 64

characters.

Image file name

Type the file name of the image that you want to send to

the FTP server using up to 10 alphanumeric characters,

- (hyphen) and _ (underscore).

Suffix

Select a suffix to be added to the file name used when the

image is sent.

None: The name of the sent file will be the image file

name.

Date & time: The date & time suffix is added to the

image file name.

The date & time suffix consists of last two-digits of

the year (2 digits), month (2 digits), date (2 digits),

hour (2 digits), minute (2 digits), second (2 digits),

and sequential number (2 digits), thus adding 14-

digit number to the image file name.

Sequence number: A sequential 10-digit number

0000000001-4294967295 and a sequential 2-digit

number are added to the image file name to be sent.

Sequence number clear

If you click Clear, the suffix of the Sequence number

returns 1.

Send

If you click Execute, the image will be sent to the FTP

server once for testing according to the settings of

manual sending.

OK/Cancel

See “Buttons common to every menu” on page 21.

Administrating the Camera

Setting the Schedule — Schedule Menu 67

Setting the Schedule

— Schedule Menu

When you click in the Administrator menu,

the Schedule menu appears.

The Schedule menu consists of the Schedule tab.

Schedule Tab

When you click the Schedule tab, the setting menu for

each action is displayed. You can set the schedule of the

following actions; Mail Transfer (Event), Mail

Transfer (Periodical), Alarm output (Event), Alarm

output (Timer), Edge Storage movie, Edge Storage

still image (Event), Edge Storage still image

(Periodical), Day/Night, Voice alert, HTTP alarm

notification (Event), Preset tour and FTP still image

sending (Periodical).

Action

Displays an action name to set the schedule.

Always

Select the checkbox to always enable the specified

condition for each action.

Always is not available for Day/Night.

Interval

You can set the interval of the action which is set to

execute periodically.

Setting the schedule

You can set the schedule by arranging the schedule area

of each action. Click on the area you want to set the

schedule; 1 block for 1 hour. When you double-click on

a selected area, the dialog of setting the start time and

duration appears, and you can set the details.

If you want to delete a schedule you have set, select the

schedule and press the delete key on your keyboard.

Note

When the execution condition of Mail Transfer is set to

Periodical, the interval can be set from 30 minutes to 24

hours.

OK/Cancel

See “Buttons common to every menu” on page 21.

Schedule

Others

Glossary

Others

Glossary

ActiveX control

A component program object that can be used with web

pages or other application programs. The technology for

creating ActiveX control is part of software developed

by Microsoft.

Bandwidth control

To limit the amount of transmitted data.

Bit rate

The rate at which data bits are transmitted.

Capture

To send audio and video converted to digital data from

video devices to a computer.

CBR

CBR stands for Constant Bit Rate control. When you

select this setting, bits will be consumed at a constant

rate.

Codec

Software/hardware for coding/decoding video and audio

data.

Contrast

The difference in tone between the lightest and darkest

portions of the image.

Default gateway

Device that can be used to access another network.

DHCP server

Acronym for Dynamic Host Configuration Protocol

server. The IP address of a terminal without an

individual IP address can be automatically distributed by

the Dynamic Host Configuration Protocol (DHCP). The

DHCP server assigns the IP addresses to the terminals.

Digital certificate

An electronic certificate that a CA (Certificate

Authority) attests that a public key to cancel a secret

code is issued by an authentic publisher.

DNS server

Acronym for Domain Name System server. As an IP

address required for connecting to the device on an IP

network is numerical and difficult to remember, the

Domain Name System was established. A domain name

is alphabetic and is easier to remember. When a client

computer uses a domain name to connect to another

computer, it asks a DNS server to translate the name into

the corresponding IP address. The client computer can

then obtain the IP address of the computer to be

connected.

Frame rate

The number of frames of a moving image that can be

transmitted per a second.

HTTP port

A port used to communicate between the web server and

the web client, such as a web browser.

H.264

An image compression format. The standard written by

the JVT (Joint Video Team) a joint organization for

standardization (composed of ISO and ITU-T), is

capable of transmitting video data at a higher

compression rate than that of MPEG4.

IP address

Acronym for Internet Protocol Address. An individual

IP address is basically assigned to each piece of

equipment connected to the Internet.

JPEG

Acronym for Joint Photographic Expert Group. The still

image compression technology or standards of ISO

(International Organization for Standardization) and

ITU-T. Popularly used as an image compression format

on the Internet, etc.

MAC address

A network address that uniquely identifies each LAN

card.

Multicast

The class D IP address assigned between 224.0.0.0 and

239.255.255.255. Using this IP address enables you to

transmit the same data to multiple equipment.

Network address

The portion that identifies the local network (subnet) in

an IP address.

Others

Glossary 69

Network bandwidth

Bit rate that can be used for networking.

NTP server

Network time server that transmits and receives time

information over the networks.

Primary DNS server

One of the DNS servers that can first reply to a request

by connected devices or other DNS servers.

Proxy server

A server or software that acts as an intermediary

between a local network and the Internet so that it can

connect to the Internet in place of a computer on a local

network.

Saturation

The degree to which a color is pure.

Secondary DNS server

Subsidiary DNS server used when a primary DNS server

cannot be used.

Sharpness

The degree to which the boundary of two portions is

clearly distinguished.

SMTP Server

A server for sending or relaying e-mail messages

between servers.

SSL

Acronym for Secure Sockets Layer. This is a protocol

developed by Netscape Communications Corporation to

be used for communications of encrypted data on the

Internet.

Subnet mask

32-bit stream used to distinguish the subnet address

from an IP address.

TCP

Acronym for Transmission Control Protocol. A standard

protocol used for Internet connection. Compared with

the other protocol, UDP, TCP provides reliable

communication but communication speed is slower.

UDP

Acronym for User Datagram Protocol. A standard

protocol used for Internet connection. Compared with

the other protocol, TCP, UDP can transmit data faster,

but reliable communication is not guaranteed.

Unicast

Transmission of data to specified equipment on a

network by specifying a single address.

VBR

VBR stands for Variable Bit Rate control. When you

select this setting, the bit rate will be adjusted to suit the

camera scene.

Others

Index

Numerics

802.1X Tab .....................................45

Access limit Tab .............................40

Access log Tab ...............................25

Access rights ..................................10

Action.............................................67

Action input Menu .........................51

Action output Menu .......................59

ActiveX control ..........................6, 68

ActiveX viewer.........................11, 12

Add.................................................49

Address...........................................60

Administrator .................................10

Administrator e-mail address .........60

Administrator menu .......................21

Administrator, User 1 to 9..............39

Alarm output Tab ...........................61

Alarm sending ................................65

Alignment.......................................31

Always............................................67

Area title.........................................30

Area zoom ......................................15

Audio sending ................................29

Audio Tab .......................................29

Audio upload..................................29

Authentication ................................60

Authentication mode ......................39

Auto clear .......................................52

Auto clear time...............................52

Auto flip .........................................48

Azimuth..........................................31

Background color ...........................31

Backup setting data ........................24

Bandwidth control..........................68

Bit rate............................................68

CA certificate .................................47

Call .................................................49

Camera control panel .....................13

Camera ID ......................................50

Camera tampering detection Tab....52

Cancel button..................................21

Capture .....................................13, 68

CBR................................................68

Clear ...............................................32

Clear all ..........................................32

Client certificate .............................46

Codec..............................................68

Color...............................................32

Common setting ...........37, 41, 46, 62

Content ...........................................60

Contrast ..........................................68

Control bar......................................15

Control panel..................................15

Control panel (Basic) .....................20

Control panel (Detail).....................20

Control panel section................12, 19

Current date & time........................22

Custom string .................................31

Date & time format ........................22

Date & time Tab .............................22

Day/Night Tab ................................31

Daylight saving time ......................23

Default gateway..............................68

Default policy .................................40

Delete .............................................48

Delete superimpose logo ................25

Delete voice alert file......................25

Detection area.................................58

Detection sensitivity .......................58

Detection size .................................58

Detection status ..............................52

DHCP server...................................68

Digital certificate............................68

DNS server .....................................68

Duration..........................................61

Edge Storage movie........................63

Edge Storage still image.................62

Edge Storage Tab............................62

Effect ..............................................32

Enable.......................................40, 52

Event condition...............................51

Event condition Tab........................51

Event triggered execution...............60

Events displayed.............................31

Exception list..................................47

Execution Condition Tab................59

Exposure.........................................26

Face detection Tab..........................57

Factory default................................24

File..................................................64

File attachment ...............................60

Filter settings ..................................55

Filter type .......................................55

Focus ........................................13, 16

Focus mode.....................................49

Focus near limit ..............................49

Format memory card ......................24

Frame rate...........................12, 28, 68

FTP server ......................................65

FTP still image sending Tab...........65

Full-screen display button ..............57

Glossary..........................................68

Greenwich Mean Time ...................23

H.264 ..............................................68

High framerate mode......................28

Highlight Compensation.................27

Horizontal tilt limit.........................49

Host name.......................................47

HTTP alarm notification 1, 2, 3 .....64

HTTP alarm notification Tab..........64

HTTP port.......................................68

Image..............................................30

Image 1, Image 2 and Image 3 .......28

Image codec....................................12

Image file name..............................63

Image size.......................................28

Information panel ...........................12

Information Tab ..............................22

Initialize Tab...................................24

Installation Tab ...............................23

Internet Explorer...............................7

Interval............................................67

Intrusion..........................................53

IP address .................................11, 68

IPv4 QoS ........................................38

Others

Index 71

IPv4 setting .................................... 36

IPv6 setting .................................... 37

JPEG .............................................. 68

Language........................................ 12

Latency........................................... 49

Left object ...................................... 53

License notice ................................ 12

Live viewer..................................... 12

Logging in.................................. 9, 11

MAC address.................................. 68

Mail Transfer Tab........................... 59

Main menu ..................................... 12

Manual sending.............................. 66

Matching decision.......................... 57

Memory card.................................. 62

Memory card trouble detection...... 61

Mic volume .................................... 29

Mode .............................................. 31

Mode of operation.......................... 13

Model Name .................................. 22

Monitor image.......................... 14, 20

Monitor screen ............................... 14

Monitored IP address ..................... 58

Motion detection Tab ..................... 52

Multicast ........................................ 68

Multicast streaming........................ 34

Near-IR compensation ................... 32

Network address............................. 68

Network address/Subnet ................ 40

Network bandwidth........................ 69

Network disconnection Tab ........... 58

Network Menu ............................... 36

Network Tab................................... 36

No................................................... 47

NTP server ..................................... 69

OK button....................................... 21

Overwrite ....................................... 62

Pan/Tilt............................... 13, 15, 17

Panorama image............................. 17

Panorama mode.............................. 49

Passing ........................................... 53

Password .................................. 39, 60

PC clock......................................... 22

Periodical execution....................... 61

Periodical sending.......................... 65

Picture ............................................ 27

Picture mode .................................. 26

Picture Tab ..................................... 26

Playback viewer ............................. 19

Plug-in free viewer................... 11, 14

POP server name............................ 60

Port No........................................... 47

Position .................................... 30, 32

Preset position.......................... 17, 30

Preset position Tab ......................... 49

Preset tour Tab ............................... 50

Primary DNS server....................... 69

Privacy masking Tab ...................... 32

Private key password...................... 47

Proxy server ................................... 69

PTZ mode....................................... 48

PTZF control Menu........................ 48

PTZF control Tab ........................... 48

QoS Tab.......................................... 37

Reboot............................................ 24

Recipient e-mail address................ 60

Recording capacity......................... 63

Recording data ............................... 62

Recording status............................. 63

Recording target............................. 63

Recording time............................... 63

Referrer check................................ 47

Referrer check tab .......................... 47

Remove .......................................... 49

Removed object.............................. 53

Rename .......................................... 49

Reset............................................... 49

Restore setting................................ 24

Resume time on inactivity.............. 50

Re-type password........................... 39

RTSP setting................................... 35

Saturation ....................................... 69

Schedule Menu............................... 67

Schedule Tab ..................................67

Screen mode...................................12

Search panel ...................................19

Search results list ........................... 19

Secondary DNS server ...................69

Security Menu................................ 39

Security Warning........................ 6, 51

Sensor input mode.......................... 52

Sensor input Tab.............................52

Serial number .................................22

Serial Tab .......................................50

Service Tab..................................... 25

Set.............................................48, 49

Setting ...................................... 12, 21

Sharpness ....................................... 69

SMTP Server............................59, 69

SMTP server name......................... 59

Software version............................. 22

SSL client authentication ............... 42

SSL server authentication .............. 41

SSL Tab..........................................40

SSL................................................. 69

Stabilizer ........................................ 23

Standard ......................................... 50

Status........................................32, 36

Streaming Tab ................................ 34

Stretch bar ...................................... 57

Subnet mask ................................... 69

Superimpose Tab............................ 30

System log Tab...............................25

System Menu.................................. 22

Target Image.............................53, 58

TCP .......................................... 18, 69

Termination .................................... 50

Text color ....................................... 31

Thumbnail ...................................... 49

Time setting.................................... 23

Time zone.......................................23

Tour ................................................ 50

Tour A to Tour E ............................50

Tour sync sending .......................... 66

Transmission Mode........................ 18

Transparent..................................... 31

Trigger size..................................... 56

Others

Index

Trigger speed..................................57

Trouble sending..............................61

UDP................................................69

Unicast............................................69

Unicast streaming...........................34

UPnP ..............................................38

User ................................................10

User name.................................39, 60

User Tab ......................................... 39

VBR................................................69

Vector dragging ..............................15

Video / Audio Menu.......................26

Video codec Tab .............................28

View panel................................12, 19

View size ........................................12

Viewer authentication.....................39

Viewer mode ............................10, 39

VMD settings .................................53

VMF ...............................................52

VMF settings..................................55

Voice alert.......................................64

Voice alert Tab................................63

Volume ...........................................13

White balance.................................27

Wide dynamic range (View-DR)....26

Zoom ..................................13, 16, 17

Zoom mode ....................................49

Sony Corporation