Table of Contents
- Table of Contents
- Location of Controls
- Connections and Preparations
- Projecting
- Using the Menus
- Using Network Features
- Error Handling
- Others
Sony VPL-VW570ES User Manual
Displayed below is the user manual for VPL-VW570ES by Sony which is a product in the Data Projectors category. This manual has pages.
Related Manuals
Operating Instructions
Before operating the unit, please read this manual and supplied Quick
Reference Manual thoroughly and retain them for future reference.
VPL-VW570ES
4-743-476-01 (1)
Video Projector
2
Table of Contents
Location of Controls
Front/Right Side ................................ 3
Rear/Left Side/Bottom ...................... 4
Remote Control ................................. 5
Connections and
Preparations
Installing the Unit .............................. 6
Adjusting the Picture Position ........... 7
Connecting to Video Equipment or a
Computer ...................................... 12
Projecting
Projecting the Picture ...................... 14
Turning Off the Power ............... 14
Watching 3D Video Images ............. 15
Using the 3D Glasses ................. 15
Using the Picture Position ............... 16
Selecting the Aspect Ratio According
to the Video Signal ....................... 18
Selecting the Picture Viewing
Mode ............................................ 21
Using the Menus
Operation through the Menus .......... 22
Picture Menu ................................... 24
Advanced Picture Menu .................. 30
Screen Menu .................................... 31
Setup Menu ...................................... 33
Function Menu ................................ 35
Items Locked by Settings
Lock ........................................ 37
Installation Menu ............................. 38
Information Menu ............................ 41
About the Preset Memory .......... 41
Using Network Features
Displaying the Control Window of
the Unit with a Web Browser ........42
Operating the Control Window ........ 43
Switching the Page .....................43
Setting the Access Limitation ....43
Confirming the Information
Regarding the Unit ..................44
Error Handling
Troubleshooting ...............................45
Warning Indicators ...........................48
Message Lists ...................................49
Others
Updating the Software .....................50
About HDR (high dynamic range) ... 50
About the simulated 3D feature ....... 50
NOTICES AND LICENSES FOR
SOFTWARE USED IN THIS
PRODUCT ....................................50
Replacing the Lamp .........................51
Cleaning ...........................................54
Specifications ...................................55
Preset Signals .............................56
Input Signals and Adjustable/
Setting Items ...........................58
Compatible 3D Signals ...............59
3D Signals and Adjustable/
Setting Items ...........................59
Aspect Mode ..............................61
Motionflow .................................62
Storage Conditions of Adjustable/
Setting Items ...........................62
Projection Distance and Lens Shift
Range ............................................64
Dimensions ......................................68
Index .................................................72
3
Front/Right Side
Warning indicators
aON/STANDBY indicator
(page 48)
bWARNING indicator (page 48)
Connectors
cLAN connector (page 42)
dHDMI 1/HDMI 2 connector
(page 12)
eTRIGGER 1/TRIGGER 2
connector (page 38)
fIR IN connector
Inputs signals to control the unit.
gREMOTE connector
Connects to a computer, etc. for remote
control.
hUSB connector (page 50)
Others
iLamp cover (page 51)
jVentilation holes (exhaust)
kVentilation holes (intake)
(page 53)
lRemote control detector
(page 7)
Location of Controls
Warning indicators
4
Rear/Left Side/Bottom
The buttons on the control panel have the same names as those on the remote control.
Control panel
a?/1 (ON/STANDBY) button
(page 7)
bINPUT button (page 14)
cMENU button (page 22)
dM/m/</, (arrow)/ (enter)
button (page 22)
eLENS button (page 7)
Others
fRemote control detector
(page 7)
gVentilation holes (intake)
(page 53)
hAC IN socket (page 7)
iProjector suspension support
attaching hole (page 69)
j Front feet (adjustable) (page 10)
Control panel
5
Remote Control aLIGHT button
Illuminates the buttons on the remote
control.
bInfrared transmitter
c?/1 (ON/STANDBY) button
(page 7)
dINPUT button (page 14)
eCALIBRATED PRESET buttons
(page 21)
fLENS ADJUSTMENT buttons
(page 8)
gPOSITION button (page 16)
hRESET button (page 23)
iM/m/</, (arrow)/ (enter)
buttons (page 22)
jMENU button (page 22)
kMOTIONFLOW button (page 26)
lASPECT button (page 18)
mCOLOR SPACE button (page 29)
nCOLOR TEMP button (page 27)
oGAMMA CORRECTION button
(page 28)
p3D button (page 15)
qREALITY CREATION button
(page 25)
rADVANCED IRIS button
(page 25)
sCONTRAST ENHANCER button
(page 25)
tSHARPNESS +/– button
(page 27)
uCONTRAST +/– button (page 26)
vBRIGHTNESS +/– button
(page 26)
6
Installing the Unit
The installation distance between the unit
and a screen varies depending on the size of
the screen or whether or not you use the lens
shift features. Install this unit so that it fits
the size of your screen. For details on the
distance between the unit and the screen (the
projection distance) and the size of projected
video, see “Projection Distance and Lens
Shift Range” (page 64).
1Position the unit so that the lens is
parallel to the screen.
Top view
2Project an image on the screen and
adjust the picture so that it fits the
screen (page 7).
When using a screen with an uneven surface,
stripes pattern may rarely appear on the screen
depending on the distance between the screen
and the unit or the zooming magnifications.
This is not a malfunction of the unit.
Connections and Preparations
Screen
Note
7
Adjusting the Picture
Position
Project an image on the screen and then
adjust the picture position.
Tips
• The ?/1 (ON/STANDBY), INPUT, MENU,
and M/m/</,/ (joystick) buttons on
the side panel of the unit function the same as
those on the remote control. The LENS
button functions in the same way as the
LENS ADJUSTMENT (FOCUS, ZOOM,
SHIFT) buttons of the remote control.
• When adjusting the lens, each time you press
the LENS button on the unit, the lens
adjustment function switches between “Lens
Focus,” “Lens Zoom” and “Lens Shift.”
Depending on the installation location of the
unit, you may not be able to control it with the
remote control. In this case, point the remote
control at the remote control detector of the
unit or the screen.
1After connecting the AC power cord to
the unit, plug the AC power cord into
a wall outlet.
The ON/STANDBY indicator lights in
red and the unit goes into standby mode.
2Press the ?/1 (ON/STANDBY) button
to turn on the unit.
The ON/STANDBY indicator flashes in
green, and then lights in green.
Remote control
detector
Note
Lights in red.
Flashes in green for
tens of seconds and
then lights in green.
8
3Adjust the focus.
Press the LENS ADJUSTMENT
(FOCUS) button to display the Lens
Focus adjustment window (test pattern).
Then adjust the focus of the picture by
pressing the M/m/</, buttons.
Tips
• When “Lens Control” is set to “Off” on the
Installation menu, you cannot adjust the
focus, the picture size or the proper position
by pressing the FOCUS, ZOOM or SHIFT
buttons (page 38).
• When “Test Pattern” is set to “Off” on the
Function menu, the test pattern is not
displayed (page 36).
Adjust the lens by using buttons on the remote
control or the control panel of the unit. Never
make adjustments by directly turning the lens
with your hands, which may cause damage or
malfunction to the unit.
4Adjust the picture size.
Press the LENS ADJUSTMENT
(ZOOM) button to display the Lens
Zoom adjustment window (test pattern).
Then adjust the size of the picture by
pressing the M/m/</, buttons.
To make the picture larger, press M/,.
To make the picture smaller, press m/
<.
Note
9
5Adjust the picture position.
Press the LENS ADJUSTMENT
(SHIFT) button to display the Lens Shift
adjustment window (test pattern). Then
adjust to the proper position of the
picture by pressing the M/m/</,
buttons.
Tip
Whenever you press the button, the test
pattern disappears.
When adjusting the window position, do not
touch the lens unit, otherwise your fingers may
be pinched by the moving parts.
To adjust the horizontal position
Press </,.
The picture projected on the screen moves
right or left by a maximum of 31% of the
screen width from the center of the lens.
Top view
Press the RESET button on the remote
control while the Lens Shift adjustment
window is displayed, the horizontal position
returns to the center of the lens (factory
default position). The zoom and focus are
not changed.
Note
31% 31%1 screen width
: Picture position when moving the
picture to the left at maximum
: Picture position when moving the
picture to the right at maximum
10
To adjust the vertical position
Press M/m.
The picture projected on the screen moves
up by a maximum of 85% or moves down by
a maximum of 80% of the screen height
from the center of the lens.
Side view
The range to move the picture projected on the
screen can be adjusted only within the octagon
area illustrated below. For details, see
“Projection Distance and Lens Shift Range”
(page 64).
Range of movement of the projected
picture
To adjust the tilt of the installation
surface
If the unit is installed on an uneven surface,
use the front feet (adjustable) to keep the unit
level.
• If the unit is tilted up or down, the projected
image may be trapezoidal.
• Be careful not to catch your finger when
turning the front feet (adjustable).
Note
85%
80%
1 screen
height
: Picture position when moving the
picture upward at maximum
: Picture position when moving the
picture downward at maximum
Notes
0.85V
0.31H
H: Width of the projected picture
V: Height of the projected picture
0.31H
0.8V
Projected Picture
Front feet (adjustable)
Tur n to
adjust.
11
Lens adjustment window (test
pattern)
1.78:1 (16:9)
2.35:1
1.85:1
1.33:1 (4:3)
The dashed lines show the screen sizes of each
aspect ratio.
12
Connecting to Video Equipment or a
Computer
You can enjoy high picture quality by connecting a DVD player/recorder, Blu-ray Disc player/
recorder, or PlayStation® equipped with HDMI output to the HDMI input of the unit.
When making connections, be sure to do the following:
• Turn off all equipment before making any connections.
• Use the proper cables for each connection.
• Insert the cable plugs properly; poor connection at the plugs may cause a malfunction or poor
picture quality. When pulling out a cable, be sure to pull it out from the plug, not the cable
itself.
• Refer to the operating instructions of the connected equipment.
Right side of the unit
AV amplifier Speakers
Equipment with HDMI
output connectors
Computer
to HDMI output
HDMI cable (not supplied)
: Video signal flow Use a Premium High Speed HDMI cable on which the cable
type logo is specified.
13
• Use a Premium High Speed HDMI cable. If you use other types of cables, 4K video may not be
displayed appropriately.
• When connecting an HDMI cable to the unit, make sure the V mark on the upper part of the HDMI
input of the unit and the v mark on the connector of the cable is set at the same position.
• If the picture from equipment connected to the unit with an HDMI cable is not correct, check the
settings of the connected equipment.
• If you set your computer, such as a notebook type, to output the signal to both computer’s display
and this equipment, the picture of the equipment may not appear properly. Set your computer to
output the signal to only the external monitor. For details, refer to the computer’s operating
instructions supplied with your computer. For settings of the computer, consult with the
manufacturer of the computer.
Notes
14
Projecting the
Picture
1Turn on both the unit and the
equipment connected to the unit.
2Press INPUT to display the input
palette on the screen.
3Select the equipment from which you
want to display images.
Press INPUT repeatedly or press M/m/
(enter) to select the equipment from
which to project.
Tip
When “Status” is set to “Off” on the Setup
menu, the input palette does not appear. Press
the INPUT button to switch between input
terminals in sequence.
1Press the ?/1 (ON/STANDBY)
button.
A message “POWER OFF?” appears on
the screen.
2Press the ?/1 (ON/STANDBY) button
again before the message disappears.
The ON/STANDBY indicator flashes in
green and the fan continues to run to
reduce the internal heat.
The fan stops and the ON/STANDBY
indicator changes from flashing green to
remaining red.
The power is turned off completely, and you
can disconnect the AC power cord.
Never disconnect the AC power cord while the
indicator is flashing.
Tip
You can turn off the unit by holding the ?/1
(ON/STANDBY) button for about 1 second,
instead of performing the above steps.
Projecting
Turning Off the Power
Example: To view the picture from the
video equipment connected to the HDMI
1 connector of this unit.
Note
15
Watching 3D Video
Images
You can enjoy powerful 3D video images,
such as from 3D games and 3D Blu-ray
Discs, using the optional Active 3D Glasses
(TDG-BT500A).
1Turn on the HDMI equipment for 3D
compatibility connected to the unit,
then play the 3D content.
For details on how to play 3D content,
refer to the operating instructions for the
connected equipment.
2Turn on the unit and project the 3D
video image onto the screen.
For details on how to project the image,
see “Projecting the Picture” (page 14).
3Turn on the 3D glasses, and then put
them on so that they fit comfortably.
For details on how to use the 3D glasses,
see “Using the 3D Glasses” (page 15).
Tip
The factory default setting for ”2D-3D Display
Sel.” is “Auto” to allow projecting 3D video
images automatically when the unit detects 3D
signals.
• It may not be possible to display 3D video
image, depending on the type of signal. Set
the “2D-3D Display Sel.” to “3D,” and “3D
Format” to “Side-by-Side” or “Over-Under”
to suit the format of the 3D content you want
to watch (page 35).
• Use the 3D glasses within the
communication range (page 15).
• There are differences in perception of 3D
video images among individuals.
• When the temperature of the usage
environment is low, the 3D effect may be
diminished.
Adjusting/Setting the 3D functions
You can adjust/set the 3D functions by
pressing the 3D button on the remote control
or with the “3D Settings” of the Function
menu. For details, see “3D Settings”
(page 35).
1Turn on the 3D glasses, and register
them on the unit.
For details on how to register the 3D
glasses, refer to the operating
instructions supplied with the 3D
glasses.
2Put on the 3D glasses.
3Turn toward the screen.
Precautions for use
Misoperation may occur if:
• The viewing position is too far from the
projector
• There are other communication devices,
such as a wireless LAN (IEEE802.11 b/g/
n) or a microwave with a bandwidth of 2.4
GHz, near the unit
3D glasses communication range
Figure below indicate the communication
range of the 3D glasses. If you try to watch
3D video images from a distance greater
than the communication range or install the
unit outside the communication range, the
3D glasses may not be able to display the
images properly. Also, the distance varies
depending on the environment of the room
and installation environment of the unit.
Notes
Using the 3D Glasses
16
Top or side view Using the Picture
Position
You can store up to five combinations of lens
settings (focus, picture size, picture
position), aspect ratio, and blanking. These
settings can be recalled.
In the factory preset setting, the Picture
Position is not stored.
1Press POSITION.
The Picture Position selecting palette is
displayed.
2Press POSITION repeatedly, or press
M/m/ to select the position.
The settings of the position selected is
recalled.
Store or delete lens settings, aspect ratio,
and blanking in the “Picture Position” of
the Screen menu (page 31).
The position where the lens settings,
aspect ratio, and blanking are not stored
is displayed as “---.”
Projector
10 m 10 m
10 m
10 m
17
Image of the lens moving
In the example below, the images with
aspect ratio of 1.78:1 (16:9) and 2.35:1 are
projected on a 2.35:1 screen.
• After you have selected and confirmed the
lens position, the lens starts to move. Do not
touch, or place anything near, the lens,
otherwise it may cause injury or a
malfunction.
• If you press any button on the remote control
or the unit while the lens is moving, the lens
stops. In this case, select the lens position
again or adjust the lens manually.
• The Picture Position function is not
guaranteed to reproduce the lens settings
precisely.
• When you use the subtended screen angle of
two or more aspects using lens zoom, install
the unit within the specified parameters
referring to “Projection distance” (page 65).
With some setting positions, the range of lens
shift may be restricted, even though the unit
is installed within the specified parameters.
Notes
When a 1.78:1 (16:9) image is input
When a 2.35:1 image is input
Press the POSITION
button.
The 2.35:1 image expands to fill the screen.
18
Selecting the Aspect Ratio According to the
Video Signal
You can select an aspect ratio best suited for
the video signal received.
Press ASPECT.
Each time you press the button, you can
select the “Aspect” setting.You can also
select it using the menu (page 32).
ASPECT
button
Original image Recommended setting and resultant images
1.85:1
Squeezed 1.85:1
1.85:1 Zoom
2.35:1
Squeezed 2.35:1
2.35:1 Zoom
19
Original image Recommended setting and resultant images
1.78:1 (16:9)
1.33:1 (4:3)
1.33:1 (4:3) with side panels
Normal
2.35:1
V Stretch
When using an anamorphic lens
16:9
Squeeze
When using an anamorphic lens
20
• Selectable aspect modes vary depending on
the input signal (page 61).
• The aspect modes cannot be selected when a
computer signal is input.
Notes on switching the “Aspect”
setting
• Select the aspect mode taking into account
that changing the aspect ratio of the
original picture will provide a different
look from that of the original image.
• Note that if the unit is used for profit or for
public viewing, modifying the original
picture by switching the aspect may
constitute an infringement of the rights of
authors or producers, which are legally
protected.
Original image Recommended setting and resultant images
Squeezed
Stretch
Notes
21
Selecting the Picture Viewing Mode
You can select the picture viewing mode that
best suits the type of video source or room
conditions.
You can save and use different preset modes
for 2D/3D respectively.
Press one of the CALIBRATED PRESET
buttons.
CALIBRATED
PRESET buttons
Setting items Description
CINEMA FILM 1 Picture quality suited to reproducing the highly dynamic and
clear images typical of master positive film.
CINEMA FILM 2 Picture quality suited to reproducing the rich tone and color
typical of a movie theater, based on the Cinema Film 1.
REF A picture quality setup suitable for when you want to reproduce
faithfully the original image quality, or for enjoying image
quality, without any adjustment.
TV Picture quality suited for watching TV programs, sports,
concerts, and other video images.
PHOTO Ideal for projecting still images taken with a digital camera.
GAME Picture quality suited to gaming, with well-modulated colors
and fast response.
BRT CINE Picture quality suited for watching movies in a bright
environment, such as a living room.
BRT TV Picture quality suited for watching TV programs, sports,
concerts, and other video images in a bright environment, such
as a living room.
USER Adjusts the picture quality to suit your taste then saves the
setting. The factory default setting is the same as “REF.”
22
The menu displays used for the explanation may be different from the actual menu display.
Operation through
the Menus
The unit is equipped with an on-screen menu
for making various adjustments and settings.
If you select an item name followed by an
arrow (B), the next menu window with
setting items appears.
1Press MENU.
The menu window appears.
2Press M/m to select a menu item, and
press , or .
The items that can be set or adjusted
with the selected menu appear. The item
presently selected is shown in white.
3Press M/m to select an item you want
to set or adjust and press , or .
The setting items are displayed in a pop-
up menu, in a setting menu, in an
adjustment menu or in the next menu
window.
Pop-up menu
Setting menu
Adjustment menu
Using the Menus
Note
Setting items
23
Next menu window
4Make the setting or adjustment of an
item.
When changing the adjustment
level
Press M/, to increase the value, and
press m/< to decrease the value.
Press to store the setting and restore
the original menu screen.
When changing the setting
Press M/m to change the setting.
Press to restore the original screen.
You can restore the original screen using
< depending on the selected item.
To clear the menu
Press MENU.
To reset the picture that has been
adjusted
Select “Reset” from the Picture menu.
When the screen display appears, select
“Yes” using < and press .
All of the following settings are reset to its
factory preset value:
“Reality Creation,” “Cinema Black Pro,”
“Motionflow,” “Contrast,” “Brightness,”
“Color,” “Hue,” “Color Temp.,”
“Sharpness,” and “Expert Setting” on the
Picture menu
To reset the items that have been
adjusted
Select an item in the menu screen, and
display the pop-up menu, the setting menu,
or the adjustment menu.
Press RESET on the remote control to reset
only the selected settings to its factory preset
value.
The RESET button on the remote control is
available only when the adjustment menu or
the setting menu is selected.
Setting items
Note
24
Picture Menu
The Picture menu is used for adjusting the picture.
These items may not be adjustable or configurable, depending on the type of input signal. For details,
see “Input Signals and Adjustable/Setting Items” (page 58).
Item names in brackets represent those printed on the remote control.
Note
Setting items Description
Calib. Preset
[CALIBRATED
PRESET]
You can select the picture viewing mode that best suits the type of video
source or the environment.
You can save and use different preset modes for 2D/3D respectively.
Cinema Film 1: Picture quality suited to reproducing the highly
dynamic and clear images typical of master positive film.
Cinema Film 2: Picture quality suited to reproducing the rich tone and
color typical of a movie theater, based on the Cinema Film 1.
Reference: A picture quality setup suitable for when you want to
reproduce faithfully the original image quality, or for enjoying image
quality, without any adjustment.
TV: Picture quality suited for watching TV programs, sports, concerts,
and other video images.
Photo: Ideal for projecting still images taken with a digital camera.
Game: Picture quality suited to gaming, with well-modulated colors and
fast response.
Bright Cinema: Picture quality suited for watching movies in a bright
environment, such as a living room.
Bright TV: Picture quality suited for watching TV programs, sports,
concerts, and other video images in a bright environment, such as a
living room.
User: You can adjust the picture quality to suit your taste, and save the
setting. The factory default setting is the same as “Reference.”
Tip
Any adjustments to picture quality settings are saved for each input.
Reset Resets all currently selected Calib. Preset mode settings to their default
values (page 23).
Tip
Reset does not affect settings saved for items of “Color Temp.”
25
Reality Creation
[REALITY
CREATION]
Adjusts the detail and noise processing of images. (Super-resolution
function)
On: Adjusts the settings of “Reality Creation.”
Database: Select “Normal” or “Mastered in 4K.”
“Mastered in 4K” provides image quality suitable for Blu-ray Disc™
“Mastered in 4K” releasing from Sony Pictures Home Entertainment.
Resolution: When you increase the setting value, the texture and detail
of the picture become sharper.
Noise Filtering: When you increase the setting value, the noise
(picture roughness) becomes less prominent.
Test: On/Off: Changes “On” and “Off” at a certain frequency to check
the effect of “Reality Creation.”
Tip
The display position of status during the test works together with the
“Menu Position” setting (page 33).
Off: The “Reality Creation” function is not applied.
Cinema Black Pro
Advanced Iris
[ADVANCED
IRIS]
Dynamic Control: Adjusts the range of movement of the iris (aperture).
Full: Automatically optimizes the iris (aperture) and signal processing
according to the brightness level of the input source. This results in a
bright and high contrast image.
Limited: Provides a slower movement of the iris (aperture) and lower
brightness than “Full,” making the picture quality suitable for viewing
in a dark room.
Off: The “Dynamic Control” function is not applied.
Brightness: The higher the setting, the brighter the picture. The lower
the setting, the darker the picture.
Tip
After adjusting “Brightness,” set “Dynamic Control” according to the
brightness of the room and the picture itself.
Contrast Enhancer
[CONTRAST
ENHANCER]
Corrects the level of bright and dark parts automatically to optimize
contrast according to a scene.
Increases image sharpness and makes image dynamic.
High/Middle/Low: You can adjust the contrast enhancer.
Off: The contrast enhancer function is not applied.
Lamp Control Switches the lamp output.
High: Increases the brightness, and projects brighter images.
Low: Decreases the brightness, and enhances blacks by minimizing
brightness.
Tip
Setting “Low” reduces fan noise, while also reducing energy
consumption for longer lamp life.
Setting items Description
26
Motionflow
[MOTIONFLOW]
Impulse: Reproduces original picture quality. Provides cinema-like
picture, which may flicker.
Combination: Reduces motion blur while maintaining brightness for
high-speed picture content.
Smooth High: Provides smoother picture movement; especially
effective for film-based content.
Smooth Low: Provides smoother picture movement for standard use.
True Cinema: Images, such as a movie created in 24 frames per second,
are reproduced at the original framerate.
Off: The “Motionflow” function is not applied.
Tips
• Select “Off” if the selected “Smooth High,” “Smooth Low,” “Impulse,”
“Combination,” or “True Cinema” results in a distorted picture.
• Depending on the picture content, you may not see the effect visually
even if you have changed the settings.
Contrast
[CONTRAST]
Adjusts the contrast.
Higher values increase the sharpness in images, while lower values
decrease the sharpness.
You can make adjustments by pressing the CONTRAST +/- on the
remote control.
When the HDR signal is input with “HDR10,” “HDR Reference,”
“HLG,” or “Auto” set for “HDR,” “Contrast(HDR)” appears instead of
“Contrast.”
Brightness
[BRIGHTNESS]
Adjusts the brightness of the picture.
The higher the setting, the brighter the picture. The lower the setting, the
darker the picture.
You can make adjustments by pressing the BRIGHTNESS +/- on the
remote control.
Color Adjusts the color density.
The higher the setting, the greater the intensity. The lower the setting, the
lower the intensity.
Hue Adjusts the color tone.
The higher the setting, the more greenish the picture becomes. The lower
the setting, the more reddish the picture becomes.
Setting items Description
27
Color Temp.
[COLOR TEMP]
Adjusts the color temperature.
D93: Equivalent to 9,300 K color temperature normally used in TVs.
Gives white colors a blue tint.
D75: Equivalent to 7,500 K color temperature used as an ancillary
standard illuminant. Gives a neutral tint between “D93” and “D65.”
D65: Equivalent to 6,500 K color temperature used as a standard
illuminant. Gives white colors a red tint.
D55: Equivalent to 5,500 K color temperature used as an ancillary
standard illuminant. Gives white colors an even redder tint.
Custom 1 to 5: Enables you to adjust, set, and store your favorite color
temperature.
The factory default settings are as follows.
Custom 1: Same as “D93” color temperature setting.
Custom 2: Same as “D75” color temperature setting.
Custom 3: Same as “D65” color temperature setting.
Custom 4: Same as “D55” color temperature setting.
Custom 5: Setting that prioritizes brightness.
Tip
You can adjust each item to a color temperature according to your
preference.
Sharpness
[SHARPNESS]
Sharpens the outline of the picture, or reduces the noise.
The higher the setting, the sharper the picture. The lower the setting, the
softer the picture, thus reducing the noise.
You can make adjustments by pressing the SHARPNESS +/- on the
remote control.
Expert Setting
NR (Noise
Reduction)
Reduces the roughness or noise of the picture.
Auto: Detects the noise level to reduce the roughness or noise of the
picture automatically.
High/Middle/Low: Select a setting according to the roughness or noise
of the input signal source.
Off: The NR (noise reduction) function is not applied.
Tip
The noise level may not be detected accurately with “Auto” depending
on the input signal source. If the picture is unacceptable with “Auto,”
select a setting from among “High,” “Middle,” “Low” or “Off.”
MPEG NR
(MPEG Noise
Reduction)
Reduces block noise and mosquito noise, in particular in digital signals.
Auto: Detects the noise level to reduce the block noise and mosquito
noise of the picture automatically.
High/Middle/Low: Select a setting according to the block noise and
mosquito noise of the input signal source.
Off: The MPEG NR (MPEG noise reduction) function is not applied.
Tip
The noise level may not be detected accurately with “Auto” depending
on the input signal source. If the picture is unacceptable with “Auto,”
select a setting from among “High,” “Middle,” “Low” or “Off.”
Smooth Gradation Smooths the gradation of the flat parts of images.
High/Middle/Low: You can adjust the smooth gradation effect.
Off: The smooth gradation function is not applied.
Setting items Description
28
Film Mode According to the film source you have selected, make a setting for
playback.
Auto: Suitable for reproducing the original picture movement.
Normally, set this to “Auto.”
Off: Plays back the picture in progressive format without detecting
video signals automatically.
Gamma
Correction
[GAMMA
CORRECTION]
Adjusts the response characteristics of the tone of the picture.
Select a favorite tone from 10 options.
1.8: Bright Produces a brighter picture overall.
2.0
2.1
2.2
2.4
2.6: Dark Produces a darker picture overall.
Gamma 7: Produces a sharper picture by emphasizing darker parts.
Gamma 8: Produces a brighter picture than Gamma 7. Select this when
you watch in a bright environment, such as a living room.
Gamma 9: Produces a brighter picture than Gamma 8.
Gamma 10: Increases the sharpness in images. Select this when you
watch TV programs, etc., in a bright environment, such as a living room.
Off: The “Gamma Correction” function is not applied.
Color Correction On: Adjusts Hue, Saturation or Brightness of the selected colors.
Repeat steps 1 and 2 described below to specify the target color.
1Press M/m to select “Color Select,” then press </, to select the
color you want to adjust among “Red,” “Yellow,” “Green,” “Cyan,”
“Blue” and “Magenta.”
2Press M/m to select “Hue,” “Saturation” or “Brightness,” then adjust
them to suit your taste using </, while watching the projected
picture.
Off: The “Color Correction” effect is not applied.
Clear White Emphasizes vivid whites.
High/Low: You can adjust the “Clear White” effect.
Off: The “Clear White” effect is not applied.
x.v.Color Set this item when connecting the unit with equipment that supports
x.v.Color and playing back an x.v.Color video signal.
On: You can play back an x.v.Color video signal.
Off: The “x.v.Color” function is not applied.
Tip
Setting x.v.Color to “On” disables gamma adjustment.
Setting items Description
29
HDR Sets how to play back HDR content.
Auto: Distinguishes HDR content automatically and applies the optimal
picture quality.
When an input signal supports BT.2020, the “Color Space” is set to
“BT.2020” automatically. When a signal other than BT.2020 is input, the
mode set in “Color Space” is applied. (“BT.2020” is not available in this
case.)
HDR10: Set when playing back HDR10-compatible content.
HDR Reference: This mode is suitable for playing back HDR10-
compatible content with a maximum brightness of 1,000 nit.
HLG: Set when playing back HLG-compatible content.
Off: Set when playing back content other than HDR content.
All of the modes of “Color Space” are selectable when “HDR10,” “HDR
Reference,” “HLG,” or “Off” is selected.
• If the setting is not correct for the input content, the bright and dark
areas of the video may appear too bright or too dark.
• When setting “HDR10” or “HDR Reference,” compare the picture
quality in both modes, and select the one that optimally displays the
average brightness and tone of the bright parts.
Color Space
[COLOR SPACE]
Converts the color space.
BT.709: An ITU-R BT.709 color space, which is used for high-
definition television broadcast or Blu-ray Disc. The color space is
equivalent to sRGB.
BT.2020: The color space is wider than BT.709. Use this setting when
playing back HDR content.
Color Space 1: The color space suited for watching TV programs and
video images, such as sport, concerts, etc.
Color Space 2: The color space suited for watching TV programs, sport,
concerts, and other video images in a bright environment, such as a
living room.
Color Space 3: The color space suited for watching movies in a bright
environment, such as a living room.
Custom: You can adjust the color space setting.
When “HDR” is set to “Auto,” the selectable mode changes according to
the signal type (page 29).
Input Lag
Reduction
Reduces the delay of the display for a video.
On: Shortens the time to display the input video image; effective for
increasing the performance of the display reaction speed when using an
external controller, etc.
Off: Turns the Input Lag Reduction function off.
Tip
When “Input Lag Reduction” is set to “On,” “Motionflow” (settings other
than “Impulse”), “NR,” and “MPEG NR” cannot be set.
Setting items Description
Notes
Note
30
Advanced Picture Menu
You can adjust the gaps in color that have occurred after a long period of use.
• Auto Calibration results in relatively coarse calibration. No warranty is given for the color settings
to be the same as the factory default values.
• While performing “Pre Check” or “Adjust,” the colors are projected automatically. This is not a
malfunction.
• Do not turn off the power or operate the remote control or control panel during “Pre Check” or
“Adjust”, as the process may be canceled.
Tips
• dE is an indicator of changing color. The smaller the value of dE, the fewer the changes caused by
the color.
• Perform the calibration after the power has been on for more than 30 minutes.
• It takes a few minutes for “Pre Check” or “Adjust” to complete.
• When “Pre Check” or “Adjust” starts, the screen position may shift, as the lens returns to its factory
default position. After completion, the screen returns to its previous position automatically.
• If the environment changes, such as the brightness of the room, while performing “Pre Check” or
“Adjust”, measurement may be affected.
• If the “Pre Check” or “Adjust” function fails, try it once again.
Notes
Setting items Description
Auto Calibration Pre Check: Checks the color difference against the factory default
settings, before calibration starts.
Adjust: Performs Auto Calibration.
Before/After: Toggles the factory default setting and the setting after the
calibration at a certain frequency. You can check the effect of the
calibration by monitoring the actual image.
Reset: Resets the calibration results, and returns to the factory default
settings.
31
Screen Menu
You can set the picture size, aspect mode, etc.
These items may not be available, depending on the type of input signal. For details, see “Input
Signals and Adjustable/Setting Items” (page 58).
Item names in brackets represent those printed on the remote control.
Note
Setting items Description
Picture Position
[POSITION]
You can store up to five combinations of lens settings, aspect ratio, and
blanking.
After setting the lens, aspect, and blanking, select from “1.85:1,”
“2.35:1,” “Custom 1,” “Custom 2,” or “Custom 3” depending on the
subtended screen angle, and after confirming, continue by selecting
“Save,” “Delete,” or “Select.”
Save: Stores the current lens settings (focus, window size, window
position) in the selected position. If a setting is already stored in that
position, it is overwritten.
Delete: Deletes the stored setting. After the setting is deleted, “1.85:1,”
“2.35:1,” “Custom 1,” “Custom 2,” or “Custom 3” in the display change
to “---.”
Select: Recalls the settings of the selected position.
Tips
• The optimal aspect ratio is preset for each picture position. The aspect
ratio can be changed and saved for each picture position.
• When saving the Picture Position, temporarily move the picture from the
saving point down 5 cm or more. Move the picture up again and save.
This improves the precision of the Picture Position when calling it.
• After you have selected and confirmed the lens position, the lens starts
to move. Do not touch the lens and the area around the lens, otherwise
it may cause injury or a malfunction.
• If you press any button on the unit while the lens is moving, the lens stops.
In this case, select the lens position again or adjust the lens manually.
• When you use a 2.35:1 or a 16:9 subtended screen angle with the
Picture Position function, make sure that the installation position is
suitable (page 16).
• The Picture Position function is not guaranteed to reproduce the lens
settings precisely.
Notes
32
Aspect
[ASPECT]
You can set the aspect ratio of the picture to be displayed for the current
input signal (page 18).
You can set the function only when a video signal is input.
1.85:1 Zoom: A 1.85:1 aspect ratio picture is displayed in its original
aspect ratio, enlarged so that black bands do not appear at the top and
bottom of the screen.
2.35:1 Zoom: A 2.35:1 aspect ratio picture is displayed in its original
aspect ratio, enlarged so that black bands at the top and bottom of the
screen are as small as possible.
When you select “2.35:1 Zoom” from “Trigger Select 1/2” on the
Installation menu, a 12 V signal is output from the TRIGGER 1 or
TRIGGER 2 connector (page 38).
Normal: Input video is displayed in its original aspect ratio, enlarged to
fill the screen. This mode is suitable for viewing 1.78:1 (16:9) and 1.33:1
(4:3) video.
V Stretch: This is the most suitable mode for using a 2.35:1 screen to
view 2.35:1 video with a commercially available anamorphic lens.
When you select “V Stretch” from “Trigger Select 1/2” on the
Installation menu, a 12 V signal is output from the TRIGGER 1 or
TRIGGER 2 connector (page 38).
Squeeze: With this setting, 1.78:1 (16:9) and 1.33:1 (4:3) video will be
displayed in their correct aspect ratios when you use a commercially
available anamorphic lens.
Stretch: Displays video that has been squeezed to 1.33:1 (4:3) as 1.78:1
(16:9) aspect ratio.
Tips
• When you select “V Stretch” or “Squeeze,” select the anamorphic lens
type from “Anamorphic Lens” in the Installation menu.
• Selectable aspect modes vary depending on the input signal (page 61).
• The aspect cannot be selected for an input signal from a computer, or
an input signal with a resolution of 4096 × 2160 (pages 56, 57, 61).
Blanking This feature allows you to adjust the displayable region within the four
directions of the screen.
On: Select the edge to adjust by highlighting Left, Right, Top, or Bottom
using the M/m buttons.
Adjust the amount of blanking using the </, buttons.
Off: Turns off the Blanking function.
Tip
Depending on the aspect ratio setting, right/left blanking may not be
available.
Setting items Description
33
Setup Menu
The Setup menu is used to change the factory preset settings, etc.
Setting items Description
Status Sets whether or not the on-screen display is displayed.
Set to “Off” to turn off the on-screen displays except for certain menus,
message when turning off the power, and warning messages.
Language Selects the language used in the menu and on-screen displays.
Menu Position You can change the position to display the menu on the screen.
Bottom Left: Displays the menu on the bottom left area of the screen.
Center: Displays the menu on the center of the screen.
High Altitude Mode Sets the unit to operate at the prevailing atmospheric pressure.
On: Use this setting when using the unit at an altitude of 1,500 m
(approx. 4,900 ft) or higher.
Off: Use this setting when using the unit at normal altitudes.
Tip
When this item is set to “On,” the fan noise becomes slightly louder
since the fan speed increases.
Remote Start Sets the Remote Start settings.
On: You can turn on the power from a PC or a terminal which is
connected to a network.
Off: Turns off the Remote Start function.
Tips
• To use the function, the unit should be connected to the network in
advance (page 40).
• To turn on the power with the Remote Start function, a special
command should be sent from a PC or a terminal. For details, consult
with qualified Sony personnel.
When Remote Start is set to “On,” the standby power requirement will
increase. When Network Management is set to “On,” the Remote Start
setting is set to “On” automatically, and you cannot change the setting.
Also, this is not displayed on the menu.
Note
34
Network Management On: Set when connected to the network and continuously
communicating with the projector control equipment.
When Network Management is set to “On,” the network function is
continuously enabled. Set Network Management to “Off” when the unit
is not continuously connected to the network. If you set to “On,” the
power consumption increases.
Power Saving Sets the power saving mode.
Standby: If no signal is input for 10 minutes, power is turned off
automatically and the projector goes into standby mode.
Off: Disables the power saving function.
Lamp Setting When replacing the lamps, set the desired lamp setting
(page 51).
All Reset All settings are initialized to their factory preset values.
The “Lamp Timer” in the Information menu is not reset.
Setting items Description
Note
35
Function Menu
The Function menu is used for changing the settings of the various functions of the unit.
Setting items Description
3D Settings You can change the settings of the 3D function.
2D-3D Display
Sel.
For Switching the video images to “2D” or “3D.”
Auto: Displays 3D video images when HDMI signals with 3D
information* are input. Displays 2D video images when other signals
are input.
3D: Displays 3D video images according to the 3D system selected in
“3D Format.” However, when HDMI signals with 3D information are
input to the unit, displays 3D video images according to the 3D system
of those HDMI signals.
* The 3D information is additional information to discriminate 3D.
Some HDMI signals have additional information to discriminate 3D
and some HDMI signals have none.
3D Format: Set the 3D system when the input HDMI signals do not
include 3D information.
Simulated 3D: Converts 2D video images to 3D video images. The
setting can be made only for input the HD signals.
The simulated 3D feature may have limited effect, depending on the
video source.
There are differences in perception of 3D video images among
individuals.
Side-by-Side: Select this to display 3D images as two similar images,
side-by-side.
Over-Under: Select this to display 3D images as two similar images,
one above the other.
Tips
• “2D-3D Display Sel.” cannot be set to “3D” for some video sources.
For available 3D signals, see “Compatible 3D Signals” (page 59).
• The simulated 3D feature may have limited effect, depending on the
screen size (100 to 120 inches recommended) and the video source.
• The menu display has a ghost while a 3D video image is displayed and
is best viewed with the 3D glasses.
36
3D Depth Adjust For adjusting the depth of the 3D video images on the screen. The
setting can be made only when a 3D Format other than “Simulated 3D”
is selected.
We recommend that “3D Depth Adjust” be set to “0.” The 3D video
images may be difficult to perceive, depending on the setting of “3D
Depth Adjust.”
Simulated 3D
Effect
For adjusting the 3D effect when 2D content is converted to 3D video
images. You can select the effect from among “High,” “Middle,” and
“Low.”
Tip
There are differences in perception of 3D video images converted by the
simulated 3D function among individuals.
Dynamic Range Sets the video input level for HDMI 1 and HDMI 2 connectors.
Auto: Sets the video input level automatically.
Limited: The video input level is set for signals that are equivalent to
16-235.
Full: The video input level is set for signals that are equivalent to 0-255.
If the video output setting of the connected HDMI device is not set
correctly, light and dark parts of the video may appear too light or too
dark.
HDMI Signal Format Switches the video signal formats for 4K.
Standard Format: Displays a picture in the standard HDMI format.
Enhanced Format: Displays a picture in a more detailed HDMI format.
Tips
• A picture or sound may not be output normally when “Enhanced
Format” is selected. In this case, set to “Standard Format.”
• It may take time to display a picture after switching the video signal
formats.
Test Pattern Displays a test pattern according to the setting.
On: A test pattern appears on the screen to be used when adjusting the
lens with “Lens Focus,” “Lens Zoom,” and “Lens Shift.”
Off: A test pattern does not appear.
Tip
While the test pattern is displayed, it is only displayed in green to allow
you to adjust the focus easily.
Settings Lock Locks menu item settings to prevent operational error (page 37).
Off: Cancels the Settings Lock.
Level A: Group 1 items (below) are not displayed on the menu, and are
not available.
Level B: Group 1 and Group 2 items (below) are not displayed on the
menus, and are not available.
Setting items Description
Depth
NormalFront Depth
Note
37
Group 1 Group 2
Items Locked by Settings Lock
Picture menu
Reset
Reality Creation
Advanced Iris
Contrast Enhancer
Lamp Control
Motionflow
Contrast
Brightness
Color
Hue
Color Temp.
Sharpness
NR
MPEG NR
Smooth Gradation
Film Mode
Gamma Correction
Color Correction
Clear White
x.v.Color
HDR
Color Space
Input Lag Reduction
Advanced Picture menu
Auto Calibration
Setup menu
Status
Language
Menu Position
High Altitude Mode
Remote Start
Network Management
Power Saving
Lamp Setting
Function menu
Dynamic Range
Test Pattern
Installation menu
Image Flip
Lens Control
Anamorphic Lens
Trigger Select
IR Receiver
Panel Alignment
Network Setting
38
Installation Menu
The Installation menu is used for changing the installation settings.
Setting items Description
Image Flip Flips the picture on the screen horizontally and/or vertically.
HV: Flips the picture horizontally and vertically.
H: Flips the picture horizontally.
V: Flips the picture vertically.
Off: The picture does not flip.
Use this item for installation for the backside projection or ceiling
installation.
Lens Control Avoids any operation of the lens such as “Lens Focus,” “Lens Zoom,”
and “Lens Shift,” by mistake.
On: Enables adjustment of the lens.
Off: Prevents any adjustment of the lens.
Anamorphic Lens Select a setting to match the anamorphic lens conversion ratio.
1.24x: Select this when you use an anamorphic lens with a horizontal
rate of 1.24×.
1.32x: Select this when you use an anamorphic lens with a horizontal
rate of 1.32×.
Trigger Select Switches the output function of the TRIGGER 1/TRIGGER 2 connector.
Off: Turns off the TRIGGER connector function.
Power: Outputs 12 V signals from the TRIGGER 1/TRIGGER 2
connectors when the unit is on. The TRIGGER 1/TRIGGER 2
connectors do not output any signals when the unit is in standby.
V Stretch: Works with the “Aspect” setting’s “V Stretch”
(page 32) and outputs a 12 V signal from the TRIGGER 1 or TRIGGER
2 connector.
2.35:1 Zoom: Works with the “Aspect” setting’s “2.35:1 Zoom”
(page 32) and outputs a 12 V signal from the TRIGGER 1 or TRIGGER
2 connector.
IR Receiver Selects the remote control detectors (IR Receiver) on the front and rear
of the unit.
Front & Rear: Activates both the front and rear detectors.
Front: Activates the front detector only.
Rear: Activates the rear detector only.
39
Panel Alignment This feature allows you to adjust the gaps in the color of characters or
the picture on the screen.
Adjust: Adjusts the gaps in the colors selecting “Adjust Color” or
“Adjust Item.”
Adjust Item: Selects how to make adjustments from below.
Shift: Shifts the whole picture and makes adjustments.
Zone: Selects the desired range and makes adjustments.
Adjust Color: Assigns the desired color to adjust the gaps in color.
Select “R” (Red) or “B” (Blue) to make adjustments based on “G”
(Green).
Pattern Color: Select “R/G” (Red and Green) or “R/G/B” (White, all
colors) when “Adjust Color” is “R” (Red). Select “B/G” (Blue and
Green) or “R/G/B” (White, all colors) when the “Adjust Color” is “B”
(Blue).
Adjust: The shift adjustment and zone adjustment of the color selected
in “Adjust Color” can be made with </,, M/m buttons.
When “Shift” is selected: Assign the settings of the horizontal
direction (H) with </, buttons and the vertical direction (V) with
M/m buttons on the shift adjustment screen.
When “Zone” is selected: Select the position to adjust with </,
buttons for the horizontal position (H position) and M/m buttons for
the vertical position (V position), then press .
Set the amount to adjust with </, buttons for the horizontal
direction (H direction) and with M/m buttons for the vertical
direction (V direction). You can select the position to adjust again by
pressing .
Reset: Returns to the factory settings.
Preset: The optimized data has been preset.
Depending on the adjustments made above, colors may become uneven
or the resolution may change.
Setting items Description
Note
40
Network Setting Perform internet protocol settings.
IPv4 Setting IP Address Setup: Selects the IP address setting method.
Auto (DHCP): The IP address is assigned automatically from the
DHCP server such as a router.
Manual: Specifies the IP address manually.
When “Manual” is selected for “IP Address Setup,” input “IP
Address,” “Subnet Mask,” and “Default Gateway.” Select each item
with the M/m buttons, then press button. Select the frame to input
with the </, buttons and input the value with the M/m buttons.
When all items are entered, select “Apply,” and then press the
button. The entered settings will be registered.
IP Address: Sets the unit’s IP address.
Subnet Mask: Sets the unit’s subnet mask.
Default Gateway: Sets the unit’s default gateway.
MAC Address: Displays the unit’s MAC address. This cannot be
changed.
Apply: Enables the IP address that is set manually.
IPv6 Information Displays the IPv6 information.
When you set the IPv6 IP address, set it on a Web browser (page 42).
Setting items Description
41
Information Menu
The Information menu displays the model name, serial number, input signal type/format,
software version and the cumulated hours of usage of the lamp.
You cannot adjust or change the displays listed above.
This unit has default image data to adjust preset data for input signals appropriately according
to the signals shown in “Preset Signals” (page 56) (the preset memory). When the preset signal
is input, the unit automatically detects the signal type and recalls the data for the signal from
the preset memory to adjust it to an optimum picture. The signal type is displayed in the
Information menu.
Depending on the computer input signal, parts of screen may be hidden or displayed incorrectly.
Items Description
Model Name Displays the model name
Serial No. Displays the serial number.
Signal type Displays the resolution of the input signal which you are selecting.
When input signals with 3D information are input, the type of input
signals and the 3D format are displayed.
Color Format Displays the color format of the input signal which you are selecting.
Color Space Displays the color space of the input signal which you are selecting
(“BT.601,” “BT.709,” or “BT.2020”).
HDR Format When the input signal is compatible with HDR, “HDR10” or “HLG” is
displayed according to the input signal.
Software Version Displays the software version.
Lamp Timer Indicates how long the lamp has been turned on (total usage).
Note
About the Preset Memory
Note
Signal type
42
Connection to the network allows you to
operate the following features:
• Checking the current status of the unit
via a Web browser.
• Making the network settings for the
unit.
• Network monitoring and controlling
with control protocol (Advertisement,
ADCP, AMX DDDP (Dynamic Device
Discovery Protocol), Crestron
RoomView, Control4).
• When connecting this projector with the
network, consult with the person who sets up
the network. The network must be secured.
• When using this projector connected with the
network, access the Control window via a
Web browser and change the access
limitation of the factory preset values
(page 44). It is recommended to change the
password regularly.
• When the setting on the Web browser is
completed, close the Web browser to log out.
• The menu displays used for the explanation
below may be different depending on the
model you are using.
• Supported Web browsers are Internet
Explorer 8/9/10/11.
• The menu displays only English.
• If the browser of your computer is set to [Use
a proxy server] when you have access to the
unit from your computer, click the check
mark to set accessing without using a proxy
server.
• AMX DDDP is not compatible with IPv6.
• These network functions are available when
the unit is turned on.
Displaying the
Control Window of
the Unit with a Web
Browser
1Connect the LAN cable.
2Set the network settings for the unit
using “Network Setting” on the
Installation menu
(page 40).
3Start a Web browser on the computer,
enter the following in the address field,
then press the Enter key on your
computer.
http://xxx.xxx.xxx.xxx
(xxx.xxx.xxx.xxx: IP address for the
unit)
When connecting by the IPv6
address
http://[xxxx:xxxx:- xxxx]
You can confirm the IP address of the
unit under “Network Setting” on the
Installation menu.
The following window appears in the
Web browser:
Using Network Features
Notes LAN
Connector
LAN cable
(straight type)
(not supplied)
Hub, router, etc.
43
Once you make the network settings,
you can open the Control window only
by performing step 3 of this procedure.
Operating the
Control Window
Click one of the Page Switching buttons to
display the desired setting page.
You can limit a user for accessing any
particular page.
Administrator: Allowed access to all
pages
User: Allowed access to all pages
except the Setup page
When you access the Setup page for the first
time, input “root” as the user name and
“Projector” as the password in the
authentication dialog.
When you log in for the first time, the
window that prompts you to change the
password is displayed. Follow the
instructions on the screen to change the
password.
The name of the administrator is preset to
“root.”
Switching the Page
Setting the Access Limitation
Page Switching buttons
44
The password can be changed in the
Password page in the Setup page.
When you change the password, enter a new
password.
The password of the administrator and user
should be 8 to 16 characters that includes
both alphabet and numeric characters.
Alphabet is case-sensitive.
The default password “Projector” cannot be
set as a new password.
If you forget your password, consult with
qualified Sony personnel.
The password will be reset with your
permission.
You can confirm the current settings for the
unit on the Information page.
Note
Confirming the Information
Regarding the Unit
Entry area for [Administrator]
Entry area for [User]
Information area
45
Troubleshooting
If the unit appears to be operating erratically, try to diagnose and correct the problem using the
following instructions. If the problem persists, consult with qualified Sony personnel.
Power
Picture
Error Handling
Symptom Cause and Remedy Page
The power is not turned
on.
The power may not turn on if you turn the power off with ?/
1 (ON/STANDBY) button and turn it on again in a short
time. After about 1 minute, turn the power on.
–
Close the lamp cover securely, then tighten the screws
securely.
52
Check warning indicators. 48
The power is suddenly
turned off.
Check that “Power Saving” in the Setup menu is set to
“Standby.”
34
Set “Power Saving” to “Off.” 34
Symptom Cause and Remedy Page
No picture. Check that the connecting cable is connected to the external
equipment properly.
12
Select the input source correctly using the INPUT button. 14
Check that the computer signal is set for output to an
external monitor.
If the notebook computer, etc., signal is output to its display
and an external monitor, the external monitor’s image may
not be displayed correctly. Set your computer to output the
signal to only an external monitor.
–
The picture has ghosts. Video images are displayed in 3D. Watch the 3D video
images using the 3D glasses, and set “2D-3D Display Sel.”
to “3D.”
15, 35
Bright or dark area of the
video appears too bright
or too dark.
This symptom may occur when signal level other than those
of HDMI standard is input. Switch the output level of the
connected equipment, or switch the Dynamic Range on the
Function menu of the unit.
36
The picture is too dark. Adjust “Contrast” or “Brightness” on the Picture menu
properly.
26
The picture is not clear. Adjust the focus. 8
If the lens is clouded with dew condensation, leave the unit
for about 2 hours with the power on.
–
The color of characters or
the picture is not
appropriate.
Select the desired color registration in “Panel Alignment” of
the Installation menu.
39
46
On-screen display
Remote control
Image is left on the
screen. (image retention)
When high contrast non-moving images are displayed for a
long period of time, there may be some image retention on
the screen. This is only a temporary condition. Turning off
the power for a while will eliminate the retained image.
–
Pink or green coloring
appears on parts of the
picture about 1 to
3 minutes after startup.
This may be due to the usage environment.
Wait for about 5 minutes with the power on. The color will
disappear on its own.
–
Symptom Cause and Remedy Page
On-screen display does
not appear.
Set “Status” on the Setup menu to “On.” 33
Check if the ON/STANDBY indicator should light in green.
When the ON/STANDBY indicator blinks in green, the unit
is starting up. Wait until it stops blinking and remains lit in
green.
7
The model name does not
disappear from the
screen.
The display mode of the unit may be set at the time of
purchase. Consult with your local dealer or qualified Sony
personnel.
–
Symptom Cause and Remedy Page
The remote control does
not work.
Batteries could be weak. Replace them with new batteries. –
Insert the batteries with the correct polarities. –
If there is a fluorescent lamp near the remote control
detector, the unit may work improperly or inadvertently.
–
Confirm the position of the remote control detector on the
unit.
3, 4
Set “IR Receiver” to “Front & Rear” on the Installation
menu.
38
Make sure that the cable is not connected to the IR IN
connector.
3
Symptom Cause and Remedy Page
47
3D video images
Others
Symptom Cause and Remedy Page
The video image does not
seem like 3D video
images.
Check if the 3D glasses are turned on. 15
Make sure that the battery in the 3D glasses could be weak
or is sufficiently charged.
–
Set “2D-3D Display Sel.” to “Auto” or “3D.” 35
Check if the input signals are compatible 3D signals. 59
The 3D signals may not be input depending on the
specifications of the connected AV selector/AV amplifier/
external equipment. If the 3D signal is not input, confirm
the specifications and/or settings of the AV selector/AV
amplifier/external equipment.
–
When the viewing position is too far from the unit, the 3D
glasses may not be able to display the images properly.
15
The screen size is not appropriate. Set the zooming
magnification to low or watch the image from farther away
from the screen.
64
For details, see “Precautions for use” of “Using the 3D
Glasses.”
15
Symptom Cause and Remedy Page
The fan is noisy. Check the setting of “High Altitude Mode” on the Setup
menu.
33
Make sure that the room temperature is not too high. –
Check the installation requirements of the unit.
Fan speed increases to maintain the product reliability of the
projector’s components in a room, where the temperature is
higher than normal. The fan noise becomes slightly louder.
The approximate normal temperature is 25°C (77°F).
–
The lens shift cannot be
adjusted.
The lens shift cannot be adjusted over the range of
movement. Adjust the lens shift within the range of
movement.
10, 64
48
Warning Indicators
The ON/STANDBY or WARNING indicator lights up or flashes if there is any trouble with
your projector.
If the symptom persists even after carrying out the above methods, consult with qualified Sony
personnel.
If the indicator starts flashing in a way of other than the above, turn off, and then turn on the power
with the [/1 (On/Standby) button on the remote control or control panel of the unit.
If the symptom is shown again, consult with qualified Sony personnel.
Flashing/Lighting indicators The number of
flashes
Cause and Remedy
Twice Close the lamp cover securely, then tighten
the screws securely (page 52).
Three times The temperature of lamp is unusually high.
Turn off the power and wait for the lamp to
cool, then turn on the power again.
If the symptom persists, the lamp may be at
the end of its service life. In this case,
replace the lamp with a new one (page 51).
Twice The internal temperature is unusually high.
Check to ensure that if nothing is blocking
the ventilation holes or whether or not the
unit is being used at high altitudes.
Three times The fan is broken. Consult with qualified
Sony personnel.
Note
ON/STANDBY
indicator WARNING
indicator
(Flashes in red)(Lights in red)
(Flashes in red) (Flashes in red)
Both indicators flash
49
Message Lists
Warning messages
Caution messages
Symptom Cause and Remedy Page
High temp.! Lamp off in
1 min.
Turn off the power. –
Check to ensure that nothing is blocking the ventilation
holes.
3, 4
Frequency is out of
range!
Frequency is out of range. Input a signal that is within the
acceptable frequency range of the unit.
56
Please replace the Lamp. It is time to replace the lamp. Replace the lamp.
If this message appears again after you replace the lamp, the
lamp replacement process is not complete. Check the lamp
replacement process.
To clear this message, press any button either on the remote
control or the control panel of the unit once.
51
Projector temperature is
high. High Altitude
Mode should be “On” if
projector is being used at
high altitude.
Check to ensure that nothing is blocking the ventilation
holes.
3, 4
When using the unit at high altitude, set “High Altitude
Mode” to “On.”
When temperature inside the unit remains high, “High
Altitude Mode” is switched to “On” in 1 minute, then the
fan speed increases.
33
Power Saving Mode is
set. Projector will
automatically enter
Standby Mode in 1
minute.
“Power Saving” is set to “Standby.”
If no signal is input, the power turns off after 1 minute, and
the projector goes into standby mode.
34
Symptom Cause and Remedy Page
No signal is input in the selected input. Check connections. 12
Not applicable! Press the appropriate button.
The operation to be activated by the button is currently
prohibited.
–
Settings Lock enabled. “Settings Lock” is set to “Level A” or “Level B.” 36
Note
Note
Note
x
50
Updating the
Software
You can download files to update the
software of the unit. Copy the downloaded
files to your USB memory, insert the USB
memory to the USB terminal of the unit,
then perform the update.
To use the features updated, insert a USB
memory device into a PC connected to the
internet.
Download the update files from the
following Sony website:
http://www.pro.sony.eu/
The website also explains how to install the
update.
Some USB memories may not be supported
for use. For details, refer to the website
above.
About HDR (high
dynamic range)
HDR is a video expression which improves
the ability to express dark places and bright
places compared to previous video
expressions.
About the simulated
3D feature
• Use the simulated 3D function taking into
account that the picture will provide a
different look from the original images,
because this function converts the video
images.
• Note that if the unit is used for profit or for
public viewing, displaying 2D video
images as 3D video images by converting
to the simulated 3D may constitute an
infringement of the rights of authors or
producers, which are legally protected.
NOTICES AND
LICENSES FOR
SOFTWARE USED IN
THIS PRODUCT
Refer to “Software License Information”
supplied separately.
Others
Note
51
Replacing the Lamp
The lamp used for the light source has a
certain lifespan. When the lamp dims, the
color balance of the picture becomes
strange, or “Please replace the Lamp.”
appears on the screen, the lamp may be
exhausted. Replace the lamp with a new one
(not supplied) without delay.
Tip
The lifespan of the lamp used for the light
source changes depending on the installation
environment or use conditions. You can use the
lamp longer by avoiding turning the lamp off
until several minutes pass after turning the
lamp on.
Tools you need to get started:
• Projector Lamp LMP-H280 (Optional)
• Standard Phillips screwdriver
• Cloth (for scratch protection)
Caution
• The lamp remains hot after the unit is
turned off with the ?/1 (ON/STANDBY)
button. If you touch the lamp, you may
burn your fingers. When you replace the
lamp, wait for at least 1 hour for the lamp
to cool.
• Do not touch the surface of the lamp. If
you touch it, wipe off the fingerprints with
a soft cloth.
• Pay special attention to replacing the lamp
when the unit is installed on the ceiling.
• When replacing the lamp of a unit which is
on the ceiling, do not stand directly under
the lamp cover. When removing the lamp
door (inner cover), avoid twisting it. If the
lamp explodes, fragments may cause
injury.
• When removing the lamp unit, make sure
it remains horizontal, then pull straight up.
Do not tilt the lamp unit. If you pull out the
lamp unit while tilted and if the lamp
breaks, the pieces may scatter, causing
injury.
• Be sure to use an LMP-H280 Projector Lamp
for replacement. If you use lamps other than
the LMP-H280, the unit may malfunction.
• Be sure to turn off the unit and unplug the
power cord before replacing the lamp, then
check the ON/STANDBY indicator has
already been turned off.
1Turn off the unit and unplug the AC
power cord.
2When setting the unit on a flat surface
such as a desk etc., put a cloth to
prevent the surface from being
scratched. Place the unit on the cloth.
Be sure that the unit is placed on a stable
surface.
3While pressing the part indicated
in the lamp cover illustration, slide 1
and then open 2 the lamp cover.
4Loosen the lamp door (inner cover)
screw with a Phillips screwdriver, and
then open the lamp door.
Notes
Note
52
5Loosen the 3 screws on the lamp with
the Phillips screwdriver. Hold up the
handle, then pull the lamp straight out.
• Do not loosen other screws except the 3
specified screws.
• Hold the lamp by the handle to remove
and attach it.
6Push in the new lamp by the handle
securely until it reaches the end, and
then tighten the 3 screws.
Be careful not to touch the optical block
inside the unit.
7Close the lamp door (inner cover), and
then tighten the screw.
8Close the lamp cover.
Notes
Handle
Note
53
9Wipe dust off the ventilation holes
(intake) with a soft cloth.
10Turn on the unit, then select the lamp
setting item on the Setup menu.
The menu screen below will be
appeared.
Tip
If “Settings Lock” is set to “Level B,” set to
“Off” once.
11Select “Yes.”
Caution
Do not put your hands into the lamp
replacement slot, and do not allow any liquid
or other objects into the slot to avoid
electrical shock or fire.
• The unit will not turn on unless the lamp is
securely installed in place.
• The unit will not turn on unless the lamp
cover are securely closed.
• To clear a message displayed on the screen,
press any button either on the remote control
or the control panel of the unit once.
Note on replacing the lamp when
broken, in the case of a ceiling
installation
If the lamp breaks, broken lamp pieces may
scatter and cause injury.
When the unit is on the ceiling, remove the
lamp door (inner cover) by sliding it
horizontally slowly after raising it with 30
degree opened. Avoid twisting the lamp door
(inner cover).
Notes
Ventilation holes
(intake)
Note
The lamp contains mercury. The disposal
rules for used fluorescent tubes depend on
where you live. Follow the waste disposal
policy in your area.
54
Cleaning
Cleaning the cabinet
• To remove dust from the cabinet, wipe
gently with a soft cloth. If dust is
persistent, wipe with a soft cloth slightly
moistened with a diluted mild detergent
solution.
• Never use any type of abrasive pad,
alkaline/acid cleaner, scouring powder, or
volatile solvent, such as alcohol, benzene,
thinner or insecticide.
• Clean the unit with a cleaning cloth.
Wiping with a dirty cloth may scratch the
unit.
• Using such materials or maintaining
prolonged contact with rubber or vinyl
materials may result in damage to the
screen surface and cabinet material.
55
Specifications
Item Description
Display system SXRD panel, projection system
Display device Size of effective
display area
0.74-inch (18.8 mm) SXRD
Number of pixels 26,542,080 pixels (8,847,360 pixels × 3)
Projection lens 2.06 times zoom lens (motorized)
f = 21.7 mm to 44.7 mm
F3.0 to F4.0
Light source Ultra High Pressure Lamp 280 W type
Screen size 60 inches to 300 inches (1,524 mm to 7,620 mm)
(measured diagonally)
Accepted digital signals See “Preset Signals” (page 56).
HDMI (2 inputs), HDCP compliant RGB
Y PB/CB PR/CR
Other inputs/
outputs
TRIGGER
(2 connectors)
Minijack, DC 12 V Max. 100 mA
REMOTE RS-232C: D-sub 9-pin (male)
LAN RJ45, 10BASE-T/100BASE-TX
IR IN Minijack
USB DC 5 V, Max. 500 mA
Outside dimensions (w/h/d) 495.6 mm × 205.3 mm × 463.6 mm (19 1/2 × 8 3/32 ×
18 1/4 inches) (without protrusions)
Mass Approx. 14 kg (31 lb)
Power requirements AC 100 V to 240 V, 4.6 A to 2.0 A, 50/60 Hz
Power consumption 460 W
Power consumption Standby 0.4 W (when “Remote Start” is set to “Off”)
Networked
Standby
1.0 W (LAN) (when “Remote Start” is set to “On”)
When a LAN terminal is not connected, it becomes a
low power consumption mode (0.5 W).
Operating temperature 5°C to 35°C (41°F to 95°F)
Operating humidity 35% to 85% (no condensation)
Storage temperature –20°C to +60°C (–4°F to +140°F)
Storage humidity 10% to 90%
Supplied accessories See “Checking the Supplied Accessories” in the
supplied Quick Reference Manual.
Optional accessories Projector Lamp: LMP-H280 (for replacement)
Projector Suspension Support: PSS-H10
Active 3D Glasses: TDG-BT500A
56
• The values for mass and dimensions are approximate.
• Not all optional accessories are available in all countries and area. Please check with your local
Sony Authorized Dealer.
• Information on accessories in this manual is current as of September 2018.
Design and specifications of this unit and its optional accessories are subject to change without
notice.
The following table shows the signals and video formats which you can project using this unit.
When a signal other than the preset signal shown below is input, the picture may not be
displayed properly.
Notes
Preset Signals
Preset
memory no. Preset signal (resolution) fH (kHz) fV (Hz) Sync
5 480/60p 480/60p
(Progressive NTSC)
(720 × 480p)
31.470 60.000 –
6 576/50p 576/50p
(Progressive PAL)
(720 × 576p)
31.250 50.000 –
7 1080/60i 1080/60i
(1920 × 1080i)
33.750 60.000 –
8 1080/50i 1080/50i
(1920 × 1080i)
28.130 50.000 –
10 720/60p 720/60p
(1280 × 720p)
45.000 60.000 –
11 720/50p 720/50p
(1280 × 720p)
37.500 50.000 –
12 1080/60p 1080/60p
(1920 × 1080p)
67.500 60.000 –
13 1080/50p 1080/50p
(1920 × 1080p)
56.260 50.000 –
14 1080/24p 1080/24p
(1920 × 1080p)
26.973 23.976 –
18 720/60p
(Frame packing)
720/60p
(1280 × 720p)
90.000 60.000 –
19 720/50p
(Frame packing)
720/50p
(1280 × 720p)
75.000 50.000 –
20 1080/24p
(Frame packing)
1080/24p
(1920 × 1080p)
53.946 23.976 –
26 640 × 480 VESA 60 31.469 59.940 H-NEG, V-NEG
32 800 × 600 VESA 60 37.879 60.317 H-POS, V-POS
37 1024 × 768 VESA 60 48.363 60.004 H-NEG, V-NEG
45 1280 × 960 VESA 60 60.000 60.000 H-POS, V-POS
47 1280 × 1024 VESA 60 63.974 60.013 H-POS, V-POS
50 1400 × 1050 SXGA+ 65.317 59.978 H-NEG, V-POS
55 1280 × 768 1280 × 768/60 47.776 59.870 H-NEG, V-POS
71 1920 × 1080/60i
(Frame packing)
1080/60i
(1920 × 1080i)
67.500 60.000 –
57
Preset memory numbers for each input signal
Digital signal
* Some digital signals input from computers may be displayed as preset memory number of
Component or Video GBR signal.
72 1920 × 1080/50i
(Frame packing)
1080/50i
(1920 × 1080i)
56.250 50.000 –
74 3840 × 2160/60p 3840×2160/60p
(3840 × 2160)
135.000 60.000 –
75 3840 × 2160/50p 3840 × 2160/50p
(3840 × 2160)
112.500 50.000 –
76 4096 × 2160/60p 4096 × 2160/60p
(4096 × 2160)
135.000 60.000 –
77 4096 × 2160/50p 4096 × 2160/50p
(4096 × 2160)
112.500 50.000 –
78 4096 × 2160/30p 4096 × 2160/30p
(4096 × 2160)
67.500 30.000 –
79 4096 × 2160/25p 4096 × 2160/25p
(4096 × 2160)
56.250 25.000 –
93 3840 × 2160/24p 3840 × 2160/24p
(3840 × 2160)
53.946 23.976 –
94 3840 × 2160/25p 3840 × 2160/25p
(3840 × 2160)
56.250 25.000 –
95 3840 × 2160/30p 3840 × 2160/30p
(3840 × 2160)
67.433 29.970 –
96 4096 × 2160/24p 4096×2160/24p
(4096 × 2160)
54.000 24.000 –
Signal Preset memory number
Component signal (HDMI 1, 2 connectors) 5 to 8, 10 to 14, 18 to 20, 71, 72, 74 to 79, 93 to
96
Video GBR signal (HDMI 1, 2 connectors) 5 to 8, 10 to 14, 18 to 20, 71, 72, 74 to 79, 93 to
96
Computer signal (HDMI 1, 2 connectors) 10*, 12*, 26, 32, 37, 45, 47, 50, 55
Preset
memory no. Preset signal (resolution) fH (kHz) fV (Hz) Sync
58
The items in the menus available to adjust differ depending on the input signal. The following
tables indicate them. The items that cannot be adjusted/set are not displayed in the menu.
Picture menu
z: Adjustable/can be set
–: Not adjustable/cannot be set
*1: For further details, refer to the tables in “Motionflow” (page 62).
Input Signals and Adjustable/Setting Items
Item Input signal
Component signal Video GBR signal Computer signal
Reality Creation zz–
Advanced Iris zzz
Contrast Enhancer zz–
Lamp Control zzz
Motionflow*1zz –
Contrast zzz
Brightness zzz
Color zz–
Hue zz–
Color Temp. zzz
Sharpness zz–
NR z (excluding preset
memory numbers 18
to 20, 71, and 72)
z (excluding preset
memory numbers 18
to 20, 71, and 72)
–
MPEG NR z (excluding preset
memory numbers 18
to 20, 71, and 72)
z (excluding preset
memory numbers 18
to 20, 71, and 72)
–
Smooth Gradation z (excluding preset
memory numbers 18
to 20, 71 and 72)
z (excluding preset
memory numbers 18
to 20, 71 and 72)
–
Film Mode z (excluding preset
memory numbers 5,
6, 10 to 14, 18 to 20,
74 to 79, and 93 to
96)
z (excluding preset
memory numbers 5,
6, 10 to 14, 18 to 20,
74 to 79, and 93 to
96)
–
Gamma Correction zzz
Color Correction zzz
Clear White zzz
x.v.Color z––
HDR z (preset memory
numbers 74 to 79 and
93 to 96 only)
z (preset memory
numbers 74 to 79 and
93 to 96 only)
–
Color Space zzz
59
Screen menu
z: Adjustable/can be set
–: Not adjustable/cannot be set
*1: For further details, refer to the tables in “Aspect Mode” (page 61).
When connecting a cable such as an HDMI cable, etc., check the type of the signal in the Information
menu (page 41) and “Digital signal” (page 57), and check items that are adjustable/can be set.
This unit accepts the following types of 3D signals.
*: Mandatory 3D format of the HDMI standards.
Some items on the menus may not be available to adjust/set, depending on the 3D signals.
The items that cannot be adjusted are not displayed on the menu. The following tables indicate
those items.
Item Input signal
Component signal Video GBR signal Computer signal
Aspect*1z z –
Note
Compatible 3D Signals
Resolution 3D signal format
720/60p, 720/50p Side-by-Side format
Over-Under format*
Frame packing*
1080/60i, 1080/50i Side-by-Side format*
Frame packing
1080/24p Side-by-Side format
Over-Under format*
Frame packing*
1080/60p, 1080/50p Side-by-Side format
Over-Under format
3D Signals and Adjustable/Setting Items
Item
3D signals
720/60p,
720/50p
1080/60i,
1080/50i
1080/24p 1080/60p,
1080/50p
Reality Creation zzzz
Advanced Iris – – – –
Lamp Control zzzz
Motionflow zzzz
NR ––––
MPEG NR ––––
Smooth Gradation – – – –
60
z: Adjustable/can be set
–: Not adjustable/cannot be set
*1: For further details, refer to the tables in “Aspect Mode” (page 61).
When the unit is set to convert 2D video images to 3D video images, some items on the menus
may be not available to adjust/set, depending on the “3D Format” settings on the Function
menu. The items that cannot be adjusted are not displayed on the menu. The following tables
indicate these items.
z: Adjustable/can be set
–: Not adjustable/cannot be set
*1: This item is available only when the 1080/60i or 1080/50i signal is input.
*2: For further details, refer to the tables in “Aspect Mode” (page 61).
Film Mode – z––
x.v.Color zzzz
HDR – – – –
Aspect*1zzzz
Item 3D signals
Over-Under Side-by-Side Simulated 3D
Reality Creation zzz
Advanced Iris – – –
Lamp Control zzz
Motionflow zzz
NR – – z
MPEG NR – – z
Smooth Gradation zzz
Film Mode*1–zz
x.v.Color zzz
HDR – – –
Aspect*2zzz
Item
3D signals
720/60p,
720/50p
1080/60i,
1080/50i
1080/24p 1080/60p,
1080/50p
61
Selectable items vary depending on the type of input signal or 3D format.
For details, see the tables below. Items that cannot be selected are not displayed in the menu.
2D
*1: Not displayed in the menu as fixed at Normal.
3D
Aspect Mode
Acceptable signals 4096 × 2160 3840 × 2160 1920 × 1080
1280 × 720
720 × 480
720 × 576 Others
Preset memory
number (page 56) 76 to 79, 96 74, 75, 93 to
95 7, 8, 10 to 14 5, 6 26, 32, 37, 45,
47, 50, 55
1.85:1 Zoom – zzz –
2.35:1 Zoom – zzz –
Normal zzzzz*1
V Stretch zzzz –
Squeeze zzzz –
Stretch – – – z–
Acceptable signals 1920 × 1080, 1280 × 720
3D format Side-by-Side Over-Under Frame packing Simulated 3D
Preset memory number
(page 56) 7, 8, 10 to 14 10 to 14 18 to 20, 71, 72 7, 8, 10 to 14
1.85:1 Zoom zzzz
2.35:1 Zoom zzzz
Normal zzzz
V Stretch zzzz
Squeeze zzzz
Stretch – – – –
62
Selectable items vary depending on the type of input signal or 3D format.
For details, see the tables below. Items that cannot be selected are not displayed in the menu.
2D
3D
Each adjustable/setting item is individually stored for each input connector. For further details,
see the tables below.
Preset memory numbers for each input signal
Motionflow
Acceptable signals
1920 × 1080
1280 × 720
720 × 480
720 × 576
3840 × 2160 4096 × 2160 Others
Preset memory number (page 56) 5 to 8, 10 to 14 74, 75, 93 to 95 76 to 79, 96 26, 32, 37, 45,
47, 50, 55
Impulse zzz –
Combination zz––
Smooth High zz––
Smooth Low zz––
True Cinema zz––
Acceptable
signals 1920 × 1080, 1280 × 720
3D format Frame packing Over-Under Side-by-Side Simulated 3D
Preset memory
number (page 56) 18 19 20, 71,
72 10, 12 11, 13 14 7, 8, 10 to 14 7, 8, 10 to 14
Impulse –––––– – –
Combination–––––– – –
Smooth High – – z––zz z
Smooth Low – zz–zz z z
True Cinema –––––– – –
Storage Conditions of Adjustable/Setting Items
Input Preset memory numbers
HDMI 1 (2D) 5 to 8, 10 to 14, 26, 32, 37, 45, 47, 50, 55, 74 to 79, 93 to 96
HDMI 2 (2D)
HDMI 1 (3D) 7, 8, 10 to 14, 18 to 20, 71, 72
HDMI 2 (3D)
63
Picture menu
Screen menu
Item Storage conditions
Calib. Preset For each input connector
Reset For each input connector and Calib. Preset
Reality Creation
Advanced Iris
Contrast Enhancer
Lamp Control
Motionflow
Contrast
Brightness
Color
Hue
Color Temp.
D93-D55
Custom 1-5
Gain R For each Color Temp., D93-D55 and Custom 1-5
Gain G
Gain B
Bias R
Bias G
Bias B
Sharpness For each input connector and Calib. Preset
NR
MPEG NR
Smooth Gradation
Film Mode
Gamma Correction
Color Correction
Clear White
x.v.Color
HDR
Color Space
Cyan - Red For each Color Space
Magenta - Green
Input Lag Reduction For each input connector and Calib. Preset
Item Storage conditions
Aspect For Picture Position 1.85:1, 2.35:1, or Custom 1-3
Blanking
64
Projection Distance and Lens Shift Range
The projection distance refers to the distance between the front of the lens and the projected
surface.
The lens shift range represents the distance in percent (%) by which the lens can be shifted from
the center of the projected image. The lens shift range is regarded as 0% when the point A in
the illustration (point where a line drawn from the center of the lens and the projected image
cross at right angles) is aligned with the center of the projected image and full width or full
height of the projected image is regarded as 100%.
VS +: Vertical lens shift range (up) [%]
VS –: Vertical lens shift range (down) [%]
HS +: Horizontal lens shift range (right) [%]
HS –: Horizontal lens shift range (left) [%]
Projection distance L
Projected image Front of the lens
Lens shift range
Projected image
Center of the lens
50%
50%
Center of the
projected image
Side of the unit
A
Center of the lens
Projected image
VS +
VS –
HS – HS +
Shaded region: Lens shift range
Lens shift range
Projected image
Center of the lens
50%
50%
Center of the
projected image
Top of the unit
A
65
When projecting in 1.90:1 (Native Full Display 17:9) format
Projection distance
Unit: m (inches)
Projection distance formula
D: Projected image size (Diagonal) Unit: m (inches)
Lens shift range
Projection image size Projection distance L
Diagonal Width × Height
80" (2.03 m) 1.80 × 0.95 (71 × 37) 2.32 – 4.77 (91 – 187)
100" (2.54 m) 2.25 × 1.18 (88 × 47) 2.90 – 5.97 (115 – 235)
120" (3.05 m) 2.70 × 1.42 (106 × 56) 3.49 – 7.18 (138 – 282)
150" (3.81 m) 3.37 × 1.78 (133 × 70) 4.38 – 8.98 (173 – 353)
200" (5.08 m) 4.49 × 2.37 (177 × 93) 5.85 – 11.99 (231 – 472)
Projection distance L (minimal length) Projection distance L (maximal length)
L = 0.029432 × D – 0.0434
(L = 1.158727 × D – 1.7084)
L = 0.060197 × D – 0.0420
(L = 2.369978 × D – 1.6545)
1.90
1
85%
80%
31% 31%
VS + = 85 – 2.742 × (HS + or HS –) [%]
VS – = 80 – 2.742 × (HS + or HS –) [%]
HS + = HS – = 31 – 0.365 × (VS + or VS –) [%]
66
When projecting in 1.78:1 (16:9) format
Projection distance
Unit: m (inches)
Projection distance formula
D: Projected image size (Diagonal) Unit: m (inches)
Lens shift range
Projection image size Projection distance L
Diagonal Width × Height
80" (2.03 m) 1.77 × 1.00 (70 × 39) 2.44 – 5.01 (96 – 197)
100" (2.54 m) 2.21 × 1.25 (87 × 49) 3.05 – 6.28 (121 – 247)
120" (3.05 m) 2.66 × 1.49 (105 × 59) 3.67 – 7.55 (145 – 297)
150" (3.81 m) 3.32 × 1.87 (131 × 74) 4.60 – 9.44 (181 – 371)
200" (5.08 m) 4.43 × 2.49 (174 × 98) 6.15 – 12.61 (242 – 496)
Projection distance L (minimal length) Projection distance L (maximal length)
L = 0.030934 × D – 0.0434
(L = 1.217856 × D – 1.7084)
L = 0.063269 × D – 0.0420
(L = 2.490916 × D – 1.6545)
1.78
1Video display area
Projection area
85%
80%
33% 33% VS + = 85 – 2.576 × (HS + or HS –) [%]
VS – = 80 – 2.576 × (HS + or HS –) [%]
HS + = HS – = 33 – 0.388 × (VS + or VS –) [%]
67
When projecting in 2.35:1 format
Projection distance
Unit: m (inches)
Projection distance formula
D: Projected image size (Diagonal) Unit: m (inches)
Lens shift range
Projection image size Projection distance L
Diagonal Width × Height
80" (2.03 m) 1.87 × 0.80 (74 × 31) 2.41 – 4.96 (95 – 195)
100" (2.54 m) 2.34 × 0.99 (92 × 39) 3.02 – 6.22 (119 – 244)
120" (3.05 m) 2.80 × 1.19 (110 × 47) 3.64 – 7.47 (143 – 294)
150" (3.81 m) 3.51 × 1.49 (138 × 59) 4.55 – 9.35 (180 – 368)
200" (5.08 m) 4.67 × 1.99 (184 × 78) 6.08 – 12.48 (240 – 491)
Projection distance L (minimal length) Projection distance L (maximal length)
L = 0.030617 × D – 0.0434
(L = 1.205377 × D – 1.7084)
L = 0.062621 × D – 0.0420
(L = 2.465393 × D – 1.6545)
2.35
1
Video display area
Projection area
105%
99%
31% 31% VS + = 105 – 3.387× (HS + or HS –) [%]
VS – = 99 – 3.387 × (HS + or HS –) [%]
HS + = HS – = 31 – 0.295 × (VS + or VS –) [%]
68
Dimensions
Front
Unit: mm (inches)
Bottom
Unit: mm (inches)
495.6 (19
1
/
2
)
Center of the
lens
247.8 (9
3
/
4
) 247.8 (9
3
/
4
)
212.3 (8
11
/
32
)
205.3 (8
3
/
32
)
118
(4
21
/
32
)
463.6 (18
1
/
4
)
Front of the cabinet
142.9 (5
5
/
8
) 150.6 (5
15
/
16
)
187.9 (7
13
/
32
)
81.5
(3
7
/
32
)
187.9 (7
13
/
32
)
7.5 (
9
/
32
)
98 (3
27
/
32
)
87.4 (3
7
/
16
)
81.5
(3
7
/
32
)
98 (3
27
/
32
)
409.3 (16
1
/
8
)
69
The distance between the front of the lens and the front of the cabinet
Unit: mm (inches)
Attaching the PSS-H10 projector suspension support
Front view
Unit: mm (inches)
36.8 (1
7
/
16
)
Front of the lens
Front of the cabinet
150 (5
29
/
32
)
75
(2
15
/
16
)
8
(
5
/
16
)
Ceiling
Center of the
supporting pole
The bottom
surface of the
mount bracket
Center of the lens
175 (6
7
/
8
)118 (4
21
/
32
)
70
Side view
Unit: mm (inches)
Top view
Unit: mm (inches)
Front of the cabinet
463.6 (18
1
/
4
)
258.4 (10
3
/
16
)
213.4 (8
13
/
32
) 130 (5
1
/
8
)
Front of the cabinet
213.4 (8
13
/
32
) 130 (5
1
/
8
)
Upper ceiling mount bracket
Center of the supporting pole (The center of the
supporting pole is different from that of the unit.)
45 (1
25
/
32
)
71
Holes for the ceiling mount
Use the screws with a length of 5.3 mm (7/32 inches, minimum) to 7.6 mm (5/16 inches,
maximum) for the ceiling mount.
Recommended tightening torque (tension when turning a screw towards the direction of
rotation): 1.4 ± 0.2 N-m
Unit: mm (inches)
Unit
Insert nut (M5)
Screw hole
The maximum
length of screw
The minimum
length of screw
72
Index
Numerics
3D glasses
3D glasses communication range ....... 15
Using the 3D glasses ........................... 15
3D Settings
2D-3D Display Sel. (Select) ............... 35
3D Depth Adjust ................................. 36
3D Format ........................................... 35
Simulated 3D Effect ............................ 36
3D video ................................................. 15
A
Advanced Iris .......................................... 25
All Reset ................................................. 34
Anamorphic Lens ................................... 38
Aspect
1.85:1 Zoom .................................. 18, 32
2.35:1 Zoom .................................. 18, 32
Normal .......................................... 19, 32
Squeeze ......................................... 19, 32
Stretch ........................................... 20, 32
V Stretch ....................................... 19, 32
Auto Calibration ..................................... 30
B
Blanking .................................................. 32
Brightness ............................................... 26
C
Calib. Preset
Bright Cinema ..................................... 24
Bright TV ............................................ 24
Cinema Film 1 .................................... 24
Cinema Film 2 .................................... 24
Game ................................................... 24
Photo ................................................... 24
Reference ............................................ 24
TV ....................................................... 24
User ..................................................... 24
Cinema Black Pro ................................... 25
Cleaning .................................................. 54
Clear White ............................................. 28
Color ....................................................... 26
Color Correction ..................................... 28
Color Format ........................................... 41
Color Space ....................................... 29, 41
Color Temp. (Temperature) .................... 27
Compatible 3D signals ............................ 59
Connecting to Video equipment or a
computer ..........................................12
Connectors .................................................3
Contrast ...................................................26
Contrast Enhancer ...................................25
Control panel ............................................. 4
D
Dimensions .............................................. 68
Dynamic Range .......................................36
E
Expert Setting ..........................................27
F
Film Mode ...............................................28
G
Gamma Correction ..................................28
H
HDMI Signal Format .............................. 36
HDR ........................................................ 29
HDR Format ............................................41
High Altitude Mode ................................ 33
Hue ..........................................................26
I
Image Flip ...............................................38
Input Lag Reduction ................................29
Input signals and adjustable/setting
items ...............................................58
IR Receiver ..............................................38
L
Lamp Control ..........................................25
Lamp Setting ...........................................34
Lamp Timer ............................................. 41
LAN connector ....................................3, 42
Language .................................................33
Lens adjustment window .........................11
Lens Control ............................................ 38
Location of controls
Front/Right side .....................................3
Rear/Left side/Bottom ...........................4
73
M
Menu
Advanced Picture ................................ 30
Function .............................................. 35
Information ......................................... 41
Installation .......................................... 38
Operation ............................................ 22
Picture ................................................. 24
Screen .................................................. 31
Setup ................................................... 33
Menu Position ......................................... 33
Messages
Caution ................................................ 49
Warning ............................................... 49
Motionflow ............................................. 26
MPEG NR (MPEG Noise Reduction) .... 27
N
Network Management ............................ 34
Network Setting ...................................... 40
NR (Noise Reduction) ............................ 27
P
Panel Alignment ..................................... 39
Picture Position
Picture Position ................................... 31
Using the Picture Position ................... 16
Picture position adjustment ...................... 7
Power Saving .......................................... 34
Preset memory number ........................... 41
Preset mode
BRT CINE ........................................... 21
BRT TV ............................................... 21
CINEMA FILM 1 ............................... 21
CINEMA FILM 2 ............................... 21
GAME ................................................. 21
PHOTO ............................................... 21
REF ..................................................... 21
TV ....................................................... 21
USER .................................................. 21
Preset signals .......................................... 56
Projecting the Picture .............................. 14
Projection distance ...................... 65, 66, 67
Projection distance and lens shift
range ............................................... 64
R
Reality Creation ...................................... 25
Remote control ......................................... 5
Remote control detector ........................ 3, 4
Remote Start ........................................... 33
Replacing the lamp ..................................51
Reset ........................................................24
Resetting the items ..................................23
S
Settings Lock ...........................................36
Sharpness .................................................27
Signal type ............................................... 41
Smooth Gradation ...................................27
Software Version ..................................... 41
Specifications ..........................................55
Status .......................................................33
T
Test Pattern ..............................................36
Trigger Select ..........................................38
Troubleshooting ...................................... 45
Turning off ..............................................14
Turning on .................................................7
U
Updating the software .............................50
W
Warning indicators .............................. 3, 48
X
x.v.Color ..................................................28
Trademark Information
• “PlayStation” is a registered trademark
of Sony Interactive Entertainment Inc.
• The terms HDMI and HDMI High-
Definition Multimedia Interface, and the
HDMI Logo are trademarks or registered
trademarks of HDMI Licensing
Administrator, Inc. in the United States
and other countries.
• “Blu-ray” and “Blu-ray Disc” are
trademarks of Blu-ray Disc Association.
• “x.v.Color (x.v.Colour),” “Motionflow,”
and their respective logos are trademarks
of Sony Corporation.
........................................................................
This projector supports DeepColor,
x.v.Color, LipSync, computer input signal,
3D signal and 4K signal of HDMI standards.
It also supports HDCP.
© 2018 Sony Corporation