Table of Contents
- Compliance Statements
- Warning Statements
- Safety Statements
- Product Diagram
- Product Dimensions
- Product Dimension
- Product Information
- Specifications
- Package Contents
- Installation
- Using the Grommet Mount
- Using the C-Clamp
- Attaching the Monitor Mount
- Attaching a Monitor Using the VESA Mount
- Attaching the Monitor Mount
- Removing the Monitor Mount
- Adjusting the Monitor Tilt
- Routing the Cables
StarTech.com ARMDUALPS User Manual
Displayed below is the user manual for ARMDUALPS by StarTech.com which is a product in the Monitor Mounts & Stands category. This manual has pages.
Related Manuals
1
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Compliance Statements
Use of Trademarks, Registered Trademarks, and other
Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and
other protected names and/or symbols of third-party companies not related in
any way to StarTech.com. Where they occur these references are for illustrative
purposes only and do not represent an endorsement of a product or service
by StarTech.com, or an endorsement of the product(s) to which this manual
applies by the third-party company in question. Regardless of any direct
acknowledgement elsewhere in the body of this document, StarTech.com
hereby acknowledges that all trademarks, registered trademarks, service marks,
and other protected names and/or symbols contained in this manual and
related documents are the property of their respective holders.
2
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Warning Statements
• Make sure that you assemble this product according to the instructions.
• Do not exceed the weight capacity of this product. Overloading this product
might result in injury or property damage. This product can support the
following weight: 44.09 lb. (20 kg).
• This product is intended for indoor use only and should not be used
outdoors.
Varningsmeddelanden
• Se till att du monterar produkten i enlighet med instruktionerna.
• Överskrid inte produktens viktkapacitet. Överbelastning av produkten kan
orsaka skada på person eller egendom. Denna produkt har stöd för följande
vikter: 20 kg.
• Produkten är endast avsedd för användning inomhus och ska inte användas
utomhus.
Avertissements
• Assemblez ce produit conformément aux instructions.
• Ne dépassez pas la capacité pondérale du produit. Une surcharge du produit
peut entraîner des blessures ou des dommages matériels. Ce produit peut
supporter 20 kg.
• Ce produit est uniquement destiné à une utilisation en intérieur et ne doit
pas être utilisé à l’extérieur.
Warnhinweise
• Beachten Sie bei der Montage dieses Produkts die Montageanweisungen.
• Überschreiten Sie nicht die Tragkraft dieses Produkts. Ein Überladen dieses
Produkts kann zu Verletzungen oder zur Beschädigung des Produkts führen.
Dieses Produkt ist für folgendes Gewicht geeignet: 20 kg.
• Dieses Produkt ist nur zum Gebrauch in Innenräumen vorgesehen und sollte
nicht im Freien verwendet werden.
Dichiarazioni di avvertenza
• Assicurarsi di Assemblare il prodotto secondo le istruzioni.
• Non superare la capacità di carico del prodotto. Il sovraccarico del prodotto
potrebbe causare danni o lesioni. Il prodotto è in grado di supportare i
seguenti pesi: 20 kg.
• Il prodotto è destinato all’uso in ambienti interni. Se ne sconsiglia l’impiego
in ambienti esterni.
3
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Mensagens de aviso
• Certique-se de que monta este produto de acordo com as instruções.
• Não exceda a capacidade de peso deste produto. Sobrecarregar este produto
pode resultar em ferimentos ou danos de propriedade. Este produto pode
suportar o seguinte peso: 20 kg.
• Este produto destina-se apenas a uma utilização no interior e não deve ser
utilizado no exterior.
Advertencias de uso
• Asegúrese de ensamblar este producto según las instrucciones.
• Asegúrese de no exceder la capacidad de peso de este producto. La
sobrecarga de este producto puede causar lesiones personales o daños en la
propiedad. Este producto tiene capicidad para el siguiente peso: 20 kg.
• El uso de este producto es solo para interiores y no debe utilizarse en
exteriores.
Waarschuwingen
• Zorg dat u dit product volgens de instructies in elkaar zet.
• Overschrijd de maximale capaciteit van dit product niet. Overbelasting
van dit product kan letsel of materiële schade veroorzaken. Dit product
ondersteunt het volgende gewicht: 20 kg.
• Dit product is alleen bedoeld voor binnengebruik en mag niet buiten
worden gebruikt.
注意
• 必ず取扱説明書に従って本製品の組み立てを行って下さい。
• 本製品で定められた最大積載重量を超えないようにして下さい。最大積載重量をオーバーした
場合、怪我をする恐れや器物破損の恐れがあります。
本製品は、モニター1台あたり20kgまで支
持できます。
• 本製品は、室内での使用を想定しています。戸外では使用しないで下さい。
4
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Safety Statements
Safety Measures
• Cables (including power and charging cables) should be placed and routed
to avoid creating electric, tripping or safety hazards.
Mesures de sécurité
• Les câbles (y compris les câbles d’alimentation et de chargement) doivent
être placés et acheminés de façon à éviter tout risque électrique, de chute ou
de sécurité
安全対策
• ケーブル（電源ケーブルと充電ケーブルを含む）は、適切な配置と引き回し
を行い、電気障害やつまづきの危険性など、安全上のリスクを回避するよう
にしてください。
Misure di sicurezza
• I cavi (inclusi i cavi di alimentazione e di ricarica) devono essere posizionati
e stesi in modo da evitare pericoli di inciampo, rischi di scosse elettriche o
pericoli per la sicurezza.
Säkerhetsåtgärder
• Kablar (inklusive elkablar och laddningskablar) ska dras och placeras på så
sätt att risk för snubblingsolyckor och andra olyckor kan undvikas.
5
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Table of Contents
Compliance Statements ........................................................................1
Warning Statements ..............................................................................2
Safety Statements ..................................................................................4
Product Diagram ....................................................................................6
Product Dimensions ..............................................................................7
Product Dimension ................................................................................8
Product Information .............................................................................9
Specications.............................................................................................................................................. 9
Package Contents .....................................................................................................................................10
Installation ..............................................................................................12
Using the Grommet Mount ................................................................................................................... 12
Using the C-Clamp .................................................................................................................................... 14
Attaching the Monitor Mount ..............................................................18
Attaching a Monitor Using the VESA Mount ................................................................................... 21
Attaching the Monitor Mount .............................................................................................................. 22
Removing the Monitor Mount .............................................................23
Adjusting the Monitor Tilt ....................................................................24
Routing the Cables .................................................................................24
6
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Product Diagram
1Monitor Mount (x 2) 4Support Pole
2Swivel Arm (x 4) 5C-Clamp
3Monitor Shoulder 6 Cable-Management
Clip
1
6
4
2
3
5
7
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Product Dimensions
8
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Product Dimension
9
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Product Information
Specications
Type of measurement Measurement
VESA mounting hole pattern 75x75
100x100
Tilt +90 to -15
Screen size Maximum 30 in. (762 mm)
Rotate 360
Swivel 360
Weight/Load Capacity 44.09 lb. (20 kg)
Lift 6.3 in. (160 mm)
10
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Package Contents
Swivel Arms
Qty: Four
VESA Monitor Mounts
Qty: Two
Monitor Shoulder
Qty: One
Support Pole w/ C-Clamp
Qty: One
11
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
M3 Hex Key
Qty: Two
EVA Cushion
Qty: One
Thumb Screws
Qty: Eight
12
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Installation
Using the Grommet Mount
1. Turn the Desk Mount over so that the Support Pole faces
downwards. Use the M3 Hex Keys to remove the four Hex
Screws that are holding the base of the Support Pole to the
C-Clamp.
Removing the Four Hex Screws
2. Use a Phillips Screwdriver (not included) to remove the
Screw from the Plate on the C-Clamp.
3. Remove the Plate, Two Washers, and the Knob from the
bottom of the C-Clamp.
13
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Removing the Plate from the C-Clamp
4. Remove the backing from the EVA Cushion and attach it to
the bottom of the Support Pole. Make sure that you line up
the hole on the Support Pole with the corresponding hole
on the EVA Cushion.
5. Position the Support Pole over the Grommet Hole.
6. Slide the Plate (removed in step 3) through the Threaded
Rod on the Knob.
7. Place the Knob through the Grommet Hole in the desk or
table and into the Support Pole.
8. Turn the Knob clockwise to tighten it.
14
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Using the C-Clamp
By default, the Desk Mount comes with the C-Clamp pre-
assembled. If you assembled the Grommet mount and want to
switch back to a C-Clamp.
Skip to step 5 if you do not have to reassemble the C-Clamp.
1. Insert the Knob through the hole in the C-Clamp.
Attaching the Knob to the C-Clamp
2. Place a Washer onto the Knob.
3. Place a Phillips Screw through a Round Washer, Plate, and
into the Washer on the Knob.
15
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Assembling the C-Clamp
4. Turn the Desk Mount over and use one of the M3 Hex Keys
to insert four Hex Screws through the C-Clamp and into the
base of the Mount.
Attaching the Hex Screws to the C-Clamp
5. Remove the backing from the EVA Cushion.
6. Align the adhesive side of the EVA Cushion with the bottom
of the Support Pole.
16
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Installing the EVA Cushion
7. While applying pressure x the EVA Cushion to the bottom
of the Support Pole.
8. Using your hand, tighten the Knob until the C-Clamp is
pressed tightly against the mounting surface.
17
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Securing the C-Clamp to the Mounting Surface
Note: You can adjust the size of the C-Clamp by removing
the two screws holding the upper and lower portions of the
clamp together and re-installing the screws into the lower
two screw holes.
Adjusting the C-Clamp
18
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Attaching the Monitor Mount
Once the Desk Mount has been mounted to the mounting
surface either by using the C-Clamp or Grommet.
1. Slide the Monitor Shoulder onto the Support Pole, so that
it is resting on the Cable-Management Clip.
Installing the Swivel Arm
2. Tighten the Mounting Shoulder using the Adjustment
Screw located on the side of the Monitor Shoulder, using
the M3 Hex Key. Be careful not to over-tighten the Monitor
Shoulder.
19
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Tightening the Monitor Shoulder
3. Align the Mounting Hole on Swivel Arm 1 with the
Mounting Peg on the top of the Monitor Shoulder.
4. Slide the Mounting Hole on Swivel Arm 1 over the
Mounting Peg until it clicks into place.
Sliding the Swivel Arm into Place
20
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
5. Repeat steps 8 - 9 to install Swivel Arm 2.
6. Align the Mounting Hole on Swivel Arm 3 with the
Mounting Peg on the top of Swivel Arm 1.
7. Slide the Mounting Hole on Swivel Arm 3 over the
Mounting Peg until it clicks into place.
Attaching the Swivel Arm
8. Repeat steps 11 - 12 to install Swivel Arm 4.
21
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Attaching a Monitor Using the VESA Mount
1. Align the Mounting Holes (x 4) on the Monitor Mount with
the mounting holes on the back of the Monitor.
Note: When mounting the VESA mount the orientation of
the Monitor is important.
2. Insert the Thumb Screws through the Monitor Mount and
into the back of the Monitor.
Mounting the Monitor Using the VESA Mount
3. Using your ngers, tighten the Thumb Screws.
Warning! Do not over-tighten the Thumb Screws. If you
encounter resistance while you’re tightening the Thumb
Screws, stop tightening. Failure to do so could result in dam-
age to the monitor.
22
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Attaching the Monitor Mount
Notes: Attaching the Monitor Mount may require two
people.
The Monitor Mount supports up to a maximum of 44.09 lb.
(20 kg).
1. While supporting the weight of the Monitor, carefully
align the Mounting Hole on the Monitor Mount with the
Mounting Peg on the top Swivel Arm.
2. Slide the Mounting Hole on the Monitor Mount over the
Mounting Peg until it clicks into place.
3. Using the Hex Keys, adjust the swivel tension of the
Monitor Mount by loosening or tightening the Hex Screws
located on the Monitor Mount next to the Mounting Hole.
4. Repeat Steps 1 - 3 to attached the second Monitor Mount.
23
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Removing the Monitor Mount
1. Slide the Thumb Clip towards the Monitor Mount,
disengaging the locking mechanism.
Sliding the Thumb Clip towards the Monitor Mount
2. While holding the Thumb Clip and the weight of the
Monitor Mount, lift the Monitor Mount up, sliding the
Mounting Peg out of the Mounting Hole.
24
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Adjusting the Monitor Tilt
• While supporting the weight of the Monitor, use the Hex
Key (included) to loosen or tighten the Hex Screw on the
side of the Monitor Mount, until the tension can hold the
weight of the Monitor but it is still adjustable.
Note: The screw cap located on the opposite side of the Hex
Screw is not used for tilt adjustments.
Routing the Cables
The Desk Mount comes with a Cable-Management System
that can be used to run the monitor cables down the mounting
arms.
Note: Make sure that the cables are unplugged before you
route them through the Cable-Management System.
1. Thread the Cable through the hole in the Swivel Arm.
2. Run the Cable through the Cable-Management Clip on the
side of the Support Pole.
3. Repeat steps 1 - 2 for any additional monitors.
25
Warranty Information
This product is backed by a ten-year warranty.
For further information on product warranty terms and conditions, please refer
to www.startech.com/warranty.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or
their ocers, directors, employees or agents) for any damages (whether direct
or indirect, special, punitive, incidental, consequential, or otherwise), loss of
prots, loss of business, or any pecuniary loss, arising out of or related to the use
of the product exceed the actual price paid for the product.
Some states do not allow the exclusion or limitation of incidental or
consequential damages. If such laws apply, the limitations or exclusions
contained in this statement may not apply to you.
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
25
Hard-to-nd made easy. At StarTech.com, that isn’t a slogan.
It’s a promise.
StarTech.com is your one-stop source for every connectivity part you need.
From the latest technology to legacy products — and all the parts that bridge
the old and new — we can help you nd the parts that connect your solutions.
We make it easy to locate the parts, and we quickly deliver them wherever they
need to go. Just talk to one of our tech advisors or visit our website. You’ll be
connected to the products you need in no time.
Visit www.startech.com for complete information on all StarTech.com products
and to access exclusive resources and time-saving tools.
StarTech.com is an ISO 9001 Registered manufacturer of connectivity and
technology parts. StarTech.com was founded in 1985 and has operations in the
United States, Canada, the United Kingdom and Taiwan servicing a worldwide
market.
Reviews
Share your experiences using StarTech.com products, including product
applications and setup, what you love about the products, and areas for
improvement.
StarTech.com Ltd.
45 Artisans Cres.
London, Ontario
N5V 5E9
Canada
StarTech.com LLP
2500 Creekside Pkwy.
Lockbourne, Ohio
43137
U.S.A.
StarTech.com Ltd.
Unit B, Pinnacle
15 Gowerton Rd.,
Brackmills
Northampton
NN4 7BW
United Kingdom
FR: startech.com/fr
DE: startech.com/de
ES: startech.com/es
NL: startech.com/nl
IT: startech.com/it
JP: startech.com/jp
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support